Professional Documents
Culture Documents
Koyo DL 05 User Manual
Koyo DL 05 User Manual
Table of Contents
Getting Started
i
12 12 12 12 12 13 13 14 14 15 15 15 15 16 16 17 17 18 19 19 110 110 110 111 111 111 111 111 111 112 112 112 113
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Purpose of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where to Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplemental Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Key Topics for Each Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DL05 Micro PLC Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The DL05 Micro PLC Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programming Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DirectSOFT Programming for WindowsE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handheld Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Selection Quick Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick Start for PLC Checkout and Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 1: Unpack the DL05 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 2: Connect Switches to Input Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 3: Connect the Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 4: Connect the Programming Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 5: Switch on the System Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 6: Initialize Scratchpad Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 7: Enter a Ladder Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steps to Designing a Successful System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 1: Review the Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 2: Understand the PLC Setup Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 3: Review the I/O Selection Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 4: Choose a System Wiring Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 5: Understand the System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 6: Review the Programming Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 7: Choose the Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 8: Understand the Maintenance and Troubleshooting Procedures . . . . . . . . . . . . . . . . . . . . Questions and Answers about DL05 Micro PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
Table of Contents Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Panel Layout & Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Mounting Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Input Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Protection for Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planning the Wiring Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Protection for Input and Output Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Point Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Wiring Strategies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLC Isolation Boundaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Operator Interface Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Programming Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sinking / Sourcing Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Common Terminal Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting DC I/O to Solid State Field Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solid State Input Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solid State Output Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Relay Output Wiring Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surge Suppresion For Inductive Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prolonging Relay Contact Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Input Wiring Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Output Wiring Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High-Speed I/O Wiring Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary of Specification Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Diagrams and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AR I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AR General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Input Specifications X0 X7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Relay Output Specifications Y0 Y5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005DR I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005DR General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Relay Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AD I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AD General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005DD I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005DD General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AA I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005AA General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC InputSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 26 26 27 28 28 29 210 210 210 211 211 212 212 213 213 214 214 215 216 217 217 217 219 220 221 222 223 224 225 226 226 227 227 227 228 229 229 229 230 231 231 231 232 233 233 233 234 235 235 235
iii
Table of Contents D005DA I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D005DA General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 237 237 237
iv
Table of Contents Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interfacing to Drive Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motion Profile Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Physical I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logical I/O Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup for Mode 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Profile / Velocity Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Profile Parameter Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trapezoidal Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registration Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Velocity Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Choosing the Profile Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trapezoidal Profile Defined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registration and Home Search Profiles Defined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Velocity Profile Defined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trapezoidal Profile Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trapezoidal Profile Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trapezoidal Profile Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Example Contd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preload Position Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registration Profile Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registration Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Registration Profile Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Example Contd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Home Search Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Velocity Profile Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Velocity Profile Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Velocity Profile Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Example Contd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse Output Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Guide for Mode 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 40: High-Speed Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup for Mode 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupts and the Ladder Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Interrupt Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timed Interrupt Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Input / Timed INT Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Independent Timed Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Interrupt Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timed Interrupt Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 50: Pulse Catch Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse Catch Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup for Mode 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse Catch Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 60: Discrete Inputs with Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 326 327 327 327 328 328 329 329 329 329 330 330 330 330 331 331 332 333 333 334 334 335 336 337 339 339 340 341 342 342 344 344 344 345 345 346 346 346 346 347 348 349 349 349 349 350 350 351 352 352
v
Table of Contents Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Filter Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup for Mode 60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filtered Inputs Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 352 353 353 354
vi
Table of Contents Input Points (X Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Points (Y Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Relays (C Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timers and Timer Status Bits (T Data type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Current Values (V Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counters and Counter Status Bits (CT Data type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counter Current Values (V Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Word Memory (V Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stages (S Data type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Relays (SP Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DL05 System V-memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Parameters and Default Data Locations (V Data Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . DL05 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Input Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Y Output Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stage Control / Status Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Relay Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Status Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counter Status Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Configuration and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the DL05s Comm Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Networking DL05 to DL05 RS232C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Networking PC to DL05s RS422 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Networking DL05 Master to Other PLCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MODBUS Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DirectNET Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Slave Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MODBUS Function Codes Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Determining the MODBUS Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If Your Host Software Requires the Data Type and Address... . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 1: V2100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 2: Y20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 3: T10 Current Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 4: C54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If Your MODBUS Host Software Requires an Address ONLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 1: V2100 584/984 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 2: Y20 584/984 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 3: T10 Current Value 484 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Example 4: C54 584/984 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Determining the DirectNET Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Master Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 1: Identify Master Port # and Slave # . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 2: Load Number of Bytes to Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 3: Specify Master Memory Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 4: Specify Slave Memory Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications from a Ladder Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiple Read and Write Interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423 423 423 423 424 424 424 425 425 425 426 426 428 429 429 429 430 431 431 432 432 432 433 433 434 435 436 436 436 437 438 438 438 438 439 440 440 440 440 440 441 442 442 443 443 444 444
vii
Table of Contents Using Boolean Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . END Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Simple Rungs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normally Closed Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contacts in Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Midline Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parallel Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Joining Series Branches in Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Joining Parallel Branches in Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Combination Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Comparative Boolean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boolean Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Immediate Boolean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boolean Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store (STR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Not (STRN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or (OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Not (ORN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And (AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Not (ANDN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Store (AND STR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Store (OR STR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out (OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Out (OR OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Not (NOT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positive Differential (PD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Positive Differential (STRPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Negative Differential (STRND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Positive Differential (ORPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Negative Differential (ORND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Positive Differential (ANDPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Negative Differential (ANDND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set (SET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pause (PAUSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Comparative Boolean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store If Equal (STRE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store If Not Equal (STRNE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or If Equal (ORE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or If Not Equal (ORNE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And If Equal (ANDE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And If Not Equal (ANDNE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store (STR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Not (STRN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or (OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Not (ORN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And (AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Not (ANDN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Immediate Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Immediate (STRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Store Not Immediate (STRNI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 54 54 54 55 55 55 56 56 56 56 57 58 59 59 59 510 510 511 511 512 512 513 513 514 514 515 515 516 516 517 517 518 518 519 520 520 520 521 521 522 522 523 523 524 524 525 525 526 526 526
viii
Table of Contents Or Immediate (ORI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Not Immediate (ORNI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OR Immediate Instructions Contd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Immediate (ANDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Not Immediate (ANDNI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out Immediate (OUTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Out Immediate (OROUTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Immediate (SETI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Immediate (RSTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer, Counter and Shift Register Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer (TMR) and Timer Fast (TMRF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Example Using Discrete Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer Example Using Comparative Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulating Timer (TMRA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulating Fast Timer (TMRAF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulating Timer Example using Discrete Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulator Timer Example Using Comparative Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counter (CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counter Example Using Discrete Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Counter Example Using Comparative Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stage Counter (SGCNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stage Counter Example Using Discrete Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stage Counter Example Using Comparative Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up Down Counter (UDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up / Down Counter Example Using Discrete Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up / Down Counter Example Using Comparative Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shift Register (SR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulator / Stack Load and Output Data Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copying Data to the Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the Accumulator Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Accumulator Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Pointers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load (LD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load Double (LDD ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load Formatted (LDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load Address (LDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out (OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out Double (OUTD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Out Formatted (OUTF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pop (POP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pop Instruction Continued . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logical Instructions (Accumulator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And (AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . And Double (ANDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or (OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Or Double (ORD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exclusive Or (XOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exclusive Or Double (XORD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526 526 527 527 527 528 528 529 529 530 530 531 532 532 533 533 534 534 535 536 537 537 538 539 539 540 541 541 542 543 543 543 544 545 546 548 549 550 551 552 552 553 553 554 555 555 556 557 558 559 560
ix
Table of Contents Compare (CMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compare Double (CMPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Math Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add (ADD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add Double (ADDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subtract (SUB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subtract Double (SUBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiply (MUL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiply Double (MULD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Divide (DIV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Divide Double (DIVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Increment (INC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decrement (DEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Increment Binary (INCB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decrement Binary (DECB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add Binary (ADDB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subtract Binary (SUBB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multiply Binary (MULB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Divide Binary (DIVB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bit Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sum (SUM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shift Left (SHFL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shift Right (SHFR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Encode (ENCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decode (DECO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Number Conversion Instructions (Accumulator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Binary (BIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Binary Coded Decimal (BCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Invert (INV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASCII to HEX (ATH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HEX to ASCII (HTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gray Code (GRAY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shuffle Digits (SFLDGT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shuffle Digits Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Move (MOV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Move Memory Cartridge / Load Label (MOVMC), (LDLBL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copy Data From a Data Label Area to V Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CPU Control Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No Operation (NOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . End (END) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop (STOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Watch Dog Timer (RSTWT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Control Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For / Next (FOR) (NEXT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Goto Subroutine (GTS) (SBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subroutine Return (RT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subroutine Return Conditional (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master Line Set (MLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master Line Reset (MLR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561 562 563 563 564 565 566 567 568 569 570 571 571 572 572 573 574 575 576 577 577 577 579 580 581 582 582 583 584 585 586 588 589 589 591 591 592 593 594 594 594 594 595 596 596 598 598 598 5101 5101
x
Table of Contents Understanding Master Control Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLS/MLR Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt (INT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Return (IRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Return Conditional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (IRTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable Interrupts (ENI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disable Interrupts (DISI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Interrupt Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timed Interrupt Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Independent Timed Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Message Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fault (FAULT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fault Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Label (DLBL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASCII Constant (ACON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Numerical Constant (NCON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Label Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Print Message (PRINT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read from Network (RX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Write to Network (WX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5101 5102 5103 5103 5103 5103 5103 5103 5104 5104 5105 5105 5106 5106 5106 5107 5107 5107 5108 5109 5113 5113 5115
xi
Table of Contents
xii
Table of Contents
Auxiliary Functions
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose of Auxiliary Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing AUX Functions via DirectSOFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing AUX Functions via the Handheld Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 2* RLL Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 21 Check Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 22 Change Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 23 Clear Ladder Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 24 Clear Ladders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 3* V-memory Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 31 Clear V Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 4* I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 41 Show I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 5* CPU Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 51 Modify Program Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 53 Display Scan Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 54 Initialize Scratchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 55 Set Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 56 CPU Network Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 57 Set Retentive Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 58 Test Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 59 Bit Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 5B Counter Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 5D Select PLC Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 6* Handheld Programmer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 61 Show Revision Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 62 Beeper On / Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 65 Run Self Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 7* EEPROM Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transferrable Memory Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 71 CPU to HPP EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 72 HPP EEPROM to CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 73 Compare HPP EEPROM to CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 74 HPP EEPROM Blank Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 75 Erase HPP EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 76 Show EEPROM Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 8* Password Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUX 81 Modify Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2 A2 A3 A3 A4 A4 A4 A4 A4 A4 A4 A4 A4 A5 A5 A5 A5 A5 A5 A6 A6 A6 A7 A7 A8 A8 A8 A8 A8 A8 A8 A9 A9 A9 A9 A9 A9 A9
xiii
Table of Contents AUX 82 Unlock CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10 AUX 83 Lock CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10
Special Relays
DL05 PLC Special Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Startup and Real-Time Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CPU Status Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulator Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSIO Pulse Catch Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSIO Pulse Output Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communication Monitoring Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equal Relays for HSIO Mode 10 Counter Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2 D2 D2 D3 D3 D4 D4 D4 D4
xiv
Table of Contents Equipotential Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications and Shielded Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Analog and RS232 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multidrop Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shielded Cables within Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6 E6 E7 E7 E7 E7
1
Manual Revisions
If you contact us in reference to this manual, remember to include the revision number.
Title: DL05 Micro PLC User Manual Manual Number: D0USERM Issue Original Date 12/98 Effective Pages Description of Changes Original Issue
1
Index
A
Accumulating Fast Timer instruction, 533 Accumulating Timer instruction, 533 Accumulator Stack Load Instructions, 543 Add Binary instruction, 572, 574 Add Double instruction, 564 Add instruction, 563 Agency approvals, 28 And Double instruction, 556 And If Equal instruction, 522 And If Not Equal instruction, 522 And Immediate instruction, 527 And instruction, 511, 555 comparative, 525 And Negative Differential instruction, 517 And Not Immediate instruction, 527 And Not instruction, 511 comparative, 525 And Positive Differential instruction, 517 And Store instruction, 512 ASCII Constant instruction, 5106, 5108 ASCII TO HEX instruction, 586 Auxiliary Functions, 48 Auxiliary functions, A2
C
Cables operator interfaces, 214 programming, 19 programming devices, 214 Calculating Program Execution Time, 419 Common terminals, 216 Communication Port Specifications, 432 Communication ports, 114 pinout diagrams, 44 Communications problems, 87 Comparative Boolean, 520 Compare Double instruction, 562 Compare instruction, 561 Components, 17 Connections operator interface, 214 power input, 19 programming devices, 19, 214, 45 Solid State field devices, 217 toggle switches, 18 Connector common terminals, 216 diagram, 216 removal, 25 Control Relay Bit Map, 430 Converge Jump instruction, 723 Converge Stage instruction, 723 Convergence Stages, 719 Converting Number Formats ASCII TO HEX, 586
B
Binary Coded Decimal instruction, 582, 584 Binary instruction, 583 Bit Operation Instructions, 578
Index2
Hex to ASCII, 587 Counter instruction, 536 Counter Instructions, 530 Counter Status Bit Map, 431 CPU changing modes, 47 configuration, A5 features, 42 hardware setup, 44 indicators, 86 instruction list, 52 Mode switch, 46 specifications, 43 status indicators, 46 CPU Indicator, 87 CPU Operation, 411 CPU Scan Time, 418
E
Emergency stop, 23 Enable Interrupt instruction, 5104 Encode instruction, 577, 579, 581 End Instruction, 54 Environmental specifications, 28 Equal relays, 39, D3, D5 Error codes code locations, 83 listing, B2B9 pulse output errors, 343 European Directives, E2 Exclusive Or Double instruction, 560 Exclusive Or instruction, 559 Execution Times, C3
D
Data Label instruction, 5106, 5108 Decrement Binary instruction, 571 Diagnostics, 82 Dimensions, 26 DIN rail mounting, 29 DirectNET, 435 Divide Double instruction, 570 Divide instruction, 569 DL05 Micro PLC front panel, 24 mounting guidelines, 26 unit dimensions, 26 Drum instruction, 62, 612 chart representation, 63 counter assignments, 66 drum control techniques, 610 EDRUM (Event Drum), 614 handheld programmer mnemonics, 616 overview of drum operation, 68 powerup state, 69 selfresetting, 611 step transition, 64 Drum sequencer programming, 112
F
Fatal Errors, 82 Fault instruction, 5107 For instruction, 597 Fuse protection, 210
G
Goto Subroutine instruction, 599 Gray Code instruction, 589
H
Handheld programmer, A6 EEPROM operations, A7 HEX TO ASCII instructions, 587 Highspeed I/O configuration, 35 discrete inputs with filter, 353 features, 32 highspeed counter, 36 highspeed interrupts, 345 I/O Point Usage, 34 modes, 34 programming, 311, 322, 341 pulse catch input, 350 pulse output, 325
Index3
Home search profile, 338 Load Formatted instruction, 550 Load instruction, 548 Load Label instruction, 591, 593 Logical Instructions, 555
I
I/O Response Time, 415 I/O Type Selection, 16 Increment Binary instruction, 571 Initial Stage instruction, 722 Initial Stages, 75 Instructions accumulator / stack Load, 543 bit operation, 578 boolean, 59 capable of run time edits, 814 comparative boolean, 520 drum, 62, 612 execution times, C2, C3, C6 immediate, 526 interrupt, 5104 list of, 52 logical, 555 math, 563 message, 5107 network, 5114 number conversion, 583 program control, 597 stage, 721 stage programming, 72 table, 592 timer, counter, and shift register, 530 Interrupt Instructions, 5104 Interrupt Return Conditional instruction, 5104 Interrupt Return instruction, 5104 Interrupts external, 347 HSIO input, 345 timed, 347 Invert instruction, 585
M
Maintenance, 82 Manual, organization, 14 Master Line Reset instruction, 5102 Master Line Set instruction, 5102 Math Instructions, 563 Memory EEPROM, 113 FLASH, 113 Memory Map, 422, 428 Message Instructions, 5107 MODBUS, 434, 441 Mode switch, 46 Modes at powerup, 47 changing, 47 Motion control profile, 325 Mounting guidelines, 26 DIN rail, 29 Move instruction, 592 Move Memory Cartridge instruction, 591, 593 Multiply Binary instruction, 576 Multiply Double instruction, 568 Multiply instruction, 567
N
Network Configuration and Connections, 432 Network Diagrams, 432, 433 Network Instructions, 5114 Network master operation, 441 Network slave operation, 436 Next instruction, 597 NonFatal Errors, 82 Normally Closed Contact, 54
J
Jump instruction, 77, 722
L
Load Address instruction, 551 Load Double instruction, 549
Index4
Not instruction, 514 Not Jump instruction, 722 Number Conversion Instructions, 583 Numbering Systems, 420 Numerical Constant instruction, 5106, 5108 starting location, 39 Print Message instruction, 5110 Profiles home search, 338 motion control, 325 registration, 330, 335 trapezoidal, 330, 332 velocity, 330, 340 Program Control Instructions, 597 Program Execution Time, 419 Program Mode, 412 Programming, concepts, 112 Programming Methods, 15 examples, 110
O
Or Double instruction, 558 Or If Equal instruction, 521 Or If Not Equal instruction, 521 Or Immediate instruction, 526 Or instruction, 510, 557 comparative, 524 Or Negative Differential instruction, 516 Or Not Immediate instruction, 526 Or Not instruction, 510 comparative, 524 Or Out Immediate instruction, 528 Or Out instruction, 513 Or Positive Diffential instruction, 516 Or Store instruction, 512 Out Double instruction, 552 Out Formatted instruction, 553 Out Immediate instruction, 528 Out instruction, 513, 552 Output Data Instructions, 543
Q
Quick Start, 17
R
Read from Network instruction, 5114 Registration profile, 330, 335 Relay wiring, 219 prolonging contact life, 221 Reset Immediate instruction, 529 Reset instruction, 518 Retentive Memory Ranges, 49 Run Indicator, 87 Run Mode, 412 Run time edits, 814
P
Panel layout, 27 Part Numbers, 15, 16 Password, 410, A8 Pause instruction, 519 PLC Numbering Systems, 420 Pop instruction, 553 Positive Differential instruction, 514 Power indicator, 86 Power wiring, 19 Presets, 38 calculating values, 310
S
Safety guidelines, 22 Scratchpad memory, 110 Set Immediate instruction, 529 Set instruction, 518 Shift Register instruction, 542 Shift Register Instructions, 530 Shift Right instruction, 580 Shuffle Digits instruction, 590
Index5
Sinking / sourcing I/O, 215 Special relays, 38, D2 corresponding to error codes, 83 Specifications CPU, 43 D005AA, 234 D005AD, 230 D005AR, 226 D005DA, 236 D005DD, 232 D005DR, 228 environmental, 28 input power, 211 motion profiles, 328 Stage Control / Status Bit Map, 429 Stage Counter instruction, 538, 716 Stage instructions, 721 Stage programming, 112, 72 convergence, 719 emergency stop, 714 four steps to writing a stage program, 79 garage door opener example, 710 initial stages, 75 introduction, 72 jump instruction, 77 mutually exclusive transitions, 714 parallel processes, 712 parallel processing concepts, 719 power flow transition, 718 program organization, 715 questions and answers, 725 stage instruction characteristics, 76 stage view, 718 state transition diagrams, 73 supervisor process, 717 timer inside stage, 713 Standard RLL Programming, 112 Status Indicators, 46, 86 Store If Equal instruction, 520 Store If Not Equal instruction, 520 Store immediate instruction, 526 Store instruction, 59 comparative, 523 Store Negative Differential instruction, 515 Store Not Immediate instruction, 526 Store Not instruction, 59 comparative, 523 Store Positive Differential instruction, 515 Subroutine Return Conditional instruction, 599 Subroutine Return instruction, 599 Subtract Binary instruction, 573, 575 Subtract double instruction, 566 Subtract instruction, 565 Sum instruction, 578 System design, 111 System Vmemory, 426
T
Table Instructions, 592 Technical support, 12 Timer Fast instruction, 531 Timer instruction, 531 Timer Instructions, 530 Timer Status Bit Map, 431 Trapezoidal profile, 330, 332 Troubleshooting, 82 communications, 87 electrical noise, 810 error codes, B2 I/O points, 88 program debug, 811 Troubleshooting guide HSIO Mode 20, 324 HSIO Mode 30, 343
U
Up Down Counter instruction, 540
V
Vmemory, 426 Velocity profile, 330, 340
Index6
W
Web site, 12 Wiring counter input, 37 counter outputs, 37 DC inputs, 222 emergency stop, 23 encoder, 33 fuse protection, 212 High Speed I/O, 224 power input, 19, 210, 211 pulse output, 327 relay outputs, 219 prolonging contact life, 221 Solid State field devices, 217 strategies, 213 system power disconnect, 23 I/O Point Numbering, 212 DC Outputs, 223 drive inputs, 327 Wiring Guidelines, 210, 211 Write to Network instruction, 5116
X
X Input Bit Map, 429
Y
Y Output Bit Map, 429
Getting Started
11
In This Chapter. . . .
Introduction Conventions Used DL05 Micro PLC Components Programming Methods I/O Selection Quick Chart Quick Start for PLC Checkout and Programming Steps to Designing a Successful System Questions and Answers about DL05 Micro PLCs
12
Getting Started
Getting Started
Introduction
The Purpose of this Manual Thank you for purchasing a DL05 Micro PLC. This manual shows you how to install, program, and maintain all the Micro PLCs in the DL05 family. It also helps you understand how to interface them to other devices in a control system.This manual contains important information for personnel who will install DL05 PLCs, and for the PLC programmer. If you understand PLC systems our manuals will provide all the information you need to get and keep your system up and running. If you already understand the DL05 Micro PLC please read Chapter 2, Installation, Wiring, and Specifications, and proceed on to other chapters as needed. Be sure to keep this manual handy for reference when you run into questions. If you are a new DL05 customer, we suggest you read this manual completely so you can understand the wide variety of features in the DL05 family of products. We believe you will be pleasantly surprised with how much you can accomplish with PLCDirect products. If you have purchased operator interfaces or Direct SOFT, you will need to supplement this manual with the manuals that are written for these products. We realize that even though we strive to be the best, we may have arranged our information in such a way you cannot find what you are looking for. First, check these resources for help in locating the information: Table of Contents chapter and section listing of contents, in the front of this manual S Quick Guide to Contents chapter summary listing on page 14. S Appendices reference material for key topics, near the end of this manual You can also check our online resources for the latest product support information: S Internet the address of our Web site is http://www.plcdirect.com If you still need assistance, please call us at 8006330405. Our technical support group is glad to work with you in answering your questions. They are available Monday through Friday from 9:00 A.M. to 6:00 P.M. Eastern Standard Time. If you have a comment or question about any of our products, services, or manuals, please fill out and return the Suggestions card that was shipped with this manual. S
Where to Begin
Getting Started
13
Conventions Used
Getting Started When you see the light bulb icon in the left-hand margin, the paragraph to its immediate right will give you a special tip. The word TIP: in boldface will mark the beginning of the text. When you see the notepad icon in the left-hand margin, the paragraph to its immediate right will be a special note. The word NOTE: in boldface will mark the beginning of the text. When you see the exclamation mark icon in the left-hand margin, the paragraph to its immediate right will be a warning. This information could prevent injury, loss of property, or even death (in extreme cases). The word WARNING: in boldface will mark the beginning of the text. Key Topics for Each Chapter The beginning of each chapter will list the key topics that can be found in that chapter. 1
14
Getting Started
Getting Started
Chapters
The main contents of this manual are organized into the following eight chapters:
1 2 3 4 5 6 7 8
Appendices
Getting Started Installation, Wiring, and Specifications High-Speed Input and Pulse Output Features CPU Specifications and Operation Standard RLL Instructions Drum Instruction Programming RLL Plus Stage Programming Maintenance and Troubleshooting
introduces the six models in the DL05 Micro PLC family and the available I/O types. Also includes tips on getting started and how to design a successful system. shows how to prepare for system installation, and gives safety guidelines to help protect your personnel and machinery. It includes system and I/O wiring diagrams, including specifications for each of the six DL05 versions. teaches you how to configure the High-Speed I/O operation to provide counting functions, motion control profiles, input filtering, interrupt capability, and much more. We recommend studying Chapters 2 and 3 together. explains how the DL05 internal CPU controls the PLC system operation. This includes information on I/O point updates, application program execution, and memory structure. describes how each of the DL05s standard instructions operate. Example programs for both DirectSOFT and the Handheld Programmer are included. describes the powerful drum sequencer operation, including detailed theory of operation and control techniques. It reveals how drums solve sequential processes problems. ideal for the beginning programmer it shows how to develop simple state transition diagrams for your process, and then convert them to stage programs. This programming method is a real time-saver for programming and debug. is a guide designed to aid you in diagnosing, repairing and avoiding system problems. It includes tips for finding I/O circuit problems, ladder program errors, etc.
Additional reference information on the DL05 is in the following five appendices: Reference Appendices S S S S S A Auxiliary Functions B DL05 Error Codes C Instruction Execution Times D Special Relays E European Union Directives (CE)
AB CD E
Getting Started
15
Programming Methods
Two programming methods are available: RLL (Relay Ladder Logic) and RLL PLUS. RLL PLUS combines the added feature of flow chart programming (Staget) to the standard RLL language. Both the Direct SOFT programming package and the handheld programmer support RLL PLUS as well as standard RLL instructions. The DL05 Micro PLC can be programmed with one of the most advanced programming packages in the industry Direct SOFT, a Windows-based software package that supports familiar features such as cut-and-paste between applications, point-and-click editing, viewing and editing multiple application programs at the same time, etc.
16
Getting Started
Getting Started
Direct SOFT universally supports the Direct LOGIC CPU families. This means you can use the full version of Direct SOFT to program DL05, DL105, DL205, DL305, DL405 or any new CPUs we may add to our product line. (Upgrade software may be required for new CPUs as they become available.). A separate manual discusses Direct SOFT programming software. Direct SOFT version 2.4 or later is needed to program the DL05.
Handheld Programmer All DL05 Micro PLCs have built-in programming ports for use with the handheld programmer (D2HPP), the same programmer used with the DL105 and DL205 families. The handheld programmer can be used to create, modify and debug your application program. A separate manual discusses the Handheld Programmer. Only D2HPPs with firmware version 1.09 or later will program the DL05.
OUTPUTS
I/O type / Sink / commons Source
Voltage Ranges 90 120 VAC 12 24 VDC 90 120 VAC 12 24 VDC 90 120 VAC 12 24 VDC
Voltage / Current Ratings 6 27 VDC, 2A * 6 240 VAC, 2A * 6 27 VDC, 2A * 6 240 VAC, 2A * 6 27 VDC, 0.5A (Y0Y2) 6 27 VDC, 1.0A (Y3Y5) 6 27 VDC, 0.5A (Y0Y2) 6 27 VDC, 1.0A (Y3Y5) 17 240 VAC, 47 63 Hz 0.5A * 17 240 VAC, 47 63 Hz 0.5A *
AC / 2 DC / 2 AC / 2 DC / 2 AC / 2 DC / 2
Getting Started
17
18
Getting Started
Getting Started
WARNING: DO NOT wire the toggle switches as shown to 240VAC-powered units. The discrete inputs will only accept 120VAC nominal. Also, remove power and unplug the DL05 when wiring the switches. Only use UL-approved switches rated for at least 250VAC, 1A for AC inputs. Firmly mount the switches before using.
Getting Started
19
LG N 95 240 VAC
(cable comes with HPP) For replacement cable, use part # DV1000CBL
110
Getting Started
Getting Started
AUX
ENT
ENT
CLR
NEXT
$ STR
A 0
ENT
END
GX OUT A 0 ENT
SHFT
E 4
N TMR
D 3
ENT
After entering the simple example program put the PLC in Run mode by using the Mode key on the Handheld Programmer. The RUN indicator on the PLC will illuminate indicating the CPU has entered the Run mode. If not, repeat this step, ensuring the program is entered properly or refer to the troubleshooting guide in chapter 8. After the CPU enters the run mode, the output status indicator for Y0 should follow the switch status on input channel X0. When the switch is on, the output will be on.
Getting Started
111
The PLC is the heart of your automation system. Make sure you take time to understand the various features and setup requirements.
There are many considerations involved when you select your I/O type and field devices. Take time to understand how the various types of sensors and loads can affect your choice of I/O type.
Input + Common
PLC
Input Sensing
It is important to understand the various system design options that are available before wiring field devices and field-side power supplies to the Micro PLC.
+24 VDC +
Power Input
6 Outputs 8 Inputs
Commons Commons
Before you begin to enter a program, it is very helpful to understand how the DL05 system processes information. This involves not only program execution steps, but also involves the various modes of operation and memory layout characteristics.
112
Getting Started
Getting Started
The DL05 PLC instruction set provides for three main approaches to solving the application program, depicted in the figure below. S S S RLL diagram-style programming is the best tool for solving boolean logic and general CPU register/accumulator manipulation. It includes dozens of instructions, which will also be needed to augment drums and stages. The Timer/Event Drum Sequencer features up to 16 steps and offers both time and/or event-based step transitions. The DRUM instruction is best for a repetitive process based on a single series of steps. Stage programming (also called RLL Plus) is based on state-transition diagrams. Stages divide the ladder program into sections which correspond to the states in a flow chart you draw for your process.
Timer/Event Drum Sequencer (see Chapter 6) Stage Programming (see Chapter 7)
PushUP RAISE
X0
SP62
Y0 OUT
LOWER
Push DOWN
After reviewing the programming concepts above, youll be equipped with a variety of tools to write your application program. Step 7: Choose the Instructions Once you have installed the Micro PLC and understand the main programming concepts, you can begin writing your application program. At that time you will begin to use one of the most powerful instruction sets available in a small PLC.
TMR K30 CNT K10 CT3 T1
Sometimes equipment failures occur when we least expect it. Switches fail, loads short and need to be replaced, etc. In most cases, the majority of the troubleshooting and maintenance time is spent trying to locate the problem. The DL05 Micro PLC has many built-in features such as error codes that can help you quickly identify problems.
Getting Started
113
114
Getting Started
Getting Started
Q. Which devices can I connect to the communication ports of the DL05? A. Port 1: The port is RS-232C, fixed at 9600 baud, and uses the proprietary K-sequence protocol. The DL05 can also connect to MODBUS and DirectNET networks as a slave device through port 1. The port communicates with the following devices: S DV-1000 Data Access Unit or Optimation Operator interface panels S DirectSOFT (running on a personal computer) S D2-HPP handheld programmer S Other devices which communicate via K-sequence protocol should work with the DL05 Micro PLC. Contact the vendor for details. A. Port 2: The port is RS-232C, with selective baud rates (300-38,400bps), address and parity.It also supports the proprietary K-sequence protocol as well as DirectNet and Modbus and non-sequence/print protocols. Q. Can the DL05 accept 5VDC inputs? A. No, 5 volts is lower than the DC input ON threshold. However, many TTL logic circuits can drive the inputs if they are wired as open collector (sinking) inputs. See Chapter 2 for I/O wiring guidelines.
12
2-2
Safety Guidelines
NOTE: Products with CE marks perform their required functions safely and adhere to relevant standards as specified by CE directives provided they are used according to their intended purpose and that the instructions in this manual are adhered to. The protection provided by the equipment may be impaired if this equipment is used in a manner not specified in this manual. A listing of our international affiliates is availble on our Web site: http://www.plcdirect.com WARNING: Providing a safe operating environment for personnel and equipment is your responsibility and should be your primary goal during system planning and installation. Automation systems can fail and may result in situations that can cause serious injury to personnel or damage to equipment. Do not rely on the automation system alone to provide a safe operating environment. You should use external electromechanical devices, such as relays or limit switches, that are independent of the PLC application to provide protection for any part of the system that may cause personal injury or damage. Every automation application is different, so there may be special requirements for your particular application. Make sure you follow all national, state, and local government requirements for the proper installation and use of your equipment. Plan for Safety The best way to provide a safe operating environment is to make personnel and equipment safety part of the planning process. You should examine every aspect of the system to determine which areas are critical to operator or machine safety. If you are not familiar with PLC system installation practices, or your company does not have established installation guidelines, you should obtain additional information from the following sources. S NEMA The National Electrical Manufacturers Association, located in Washington, D.C., publishes many different documents that discuss standards for industrial control systems. You can order these publications directly from NEMA. Some of these include: ICS 1, General Standards for Industrial Control and Systems ICS 3, Industrial Systems ICS 6, Enclosures for Industrial Control Systems S NEC The National Electrical Code provides regulations concerning the installation and use of various types of electrical equipment. Copies of the NEC Handbook can often be obtained from your local electrical equipment distributor or your local library. S Local and State Agencies many local governments and state governments have additional requirements above and beyond those described in the NEC Handbook. Check with your local Electrical Inspector or Fire Marshall office for information. The publications mentioned provide many ideas and requirements for system safety. At a minimum, you should follow these regulations. Also, you should use the following techniques, which provide three levels of system control. S Orderly system shutdown sequence in the PLC control program S Mechanical disconnect for output module power S Emergency stop switch for disconnecting system power Installation, Wiring, and Specifications Three Levels of Protection
2-3
The first level of fault detection is ideally the PLC control program, which can identify machine problems. You must analyze your application and identify any shutdown sequences that must be performed. These types of problems are usually things such as jammed parts, etc. that do not pose a risk of personal injury or equipment damage. WARNING: The control program must not be the only form of protection for any problems that may result in a risk of personal injury or equipment damage.
Jam Detect
Emergency Stop
You should also use electromechanical devices, such as master control relays and/or limit switches, to prevent accidental equipment startup at an unexpected time. These devices should be installed in such a manner to prevent any machine operations from occurring. For example, if the machine has a jammed part the PLC control program can turn off the saw blade and retract the arbor. However, since the operator must open the guard to remove the part, you should also include a bypass switch that disconnects all system power any time the guard is opened. The machinery must provide a quick manual method of disconnecting all system power. The disconnect device or switch must be clearly labeled Emergency Stop .
Use E-Stop and Master Relay E STOP Power On Guard Limit Master Relay
Emergency Stop
Saw Arbor
After an Emergency shutdown or any other type of power interruption, there may be requirements that must be met before the PLC control program can be restarted. For example, there may be specific register values that must be established (or maintained from the state prior to the shutdown) before operations can resume. In this case, you may want to use retentive memory locations, or include constants in the control program to ensure a known starting point.
2-4
Mounting tab External Power Inputs Discrete Input Discrete Output Output Circuit Power Input Terminals Terminals (for DC output versions only)
The upper section of the connector accepts external AC line and neutral (L, N) connections on the two left-most terminals. From left to right, the next five terminals are one of the input commons (C0) and input connections X1, X3, X4, and X6. The remaining four connections are an output common (C2) and output terminals Y1, Y3, and Y5. The lower section of the connector has the chassis ground (G) and the logic ground (LG) on the two left-most terminals. The next two terminals are for the inputs X0 and X2. Next is the other input common (C1) followed by inputs X5 and X7. The last four terminals are for outputs Y0, Y2, Y4, and the second output common (C3). On DC output units, the end terminal on the right accepts power for the output stage.
WARNING: For some applications, field device power may still be present on the terminal block even though the Micro PLC is turned off. To minimize the risk of electrical shock, check all field device power before you expose or remove either connector
2-5
All of the terminals for the DL05 are contained on one connector block. In some instances, it may be desireable to remove the connector block for easy wiring. The connector is designed for easy removal with just a small screwdriver. The drawing below shows the procedure for removal at one end. Connector Removal
2. From the center of the connector block, pry upward with the screwdriver
until the connector is loose. The terminal block connector on DL05 PLCs have regular screw terminals, which will accept either standard or #1 Philips screwdriver tips. You can insert one 16 AWG wire under a terminal, or two 18 AWG wires (one on each side of the screw). Be careful not to overtighten; maximum torque is 6 inch/ounces. Spare terminal block connectors and connector covers may be ordered by individual part numbers:
Part Number D0--IOCON D0--IOCVR Qty Per Package 2 2 Description
2-6
Mounting Guidelines
In addition to the panel layout guidelines, other specifications can affect the definition and installation of a PLC system. Always consider the following: S Environmental Specifications S Power Requirements S Agency Approvals S Enclosure Selection and Component Dimensions Unit Dimensions Installation, Wiring, and Specifications The following diagram shows the outside dimensions and mounting hole locations for all versions of the DL05. Make sure you follow the installation guidelines to allow proper spacing from other components.
4.72 120mm 2.56 65mm
3.74 95mm
3.34 85mm
Enclosures
Your selection of a proper enclosure is important to ensure safe and proper operation of your DL05 system. Applications of DL05 systems vary and may require additional features. The minimum considerations for enclosures include: S Conformance to electrical standards S Protection from the elements in an industrial environment S Common ground reference S Maintenance of specified ambient temperature S Access to equipment S Security or restricted access S Sufficient space for proper installation and maintenance of equipment
2-7
There are many things to consider when designing the panel layout. The following items correspond to the diagram shown. Note: there may be additional requirements, depending on your application and use of other components in the cabinet. 1. Mount the PLCs horizontally as shown below to provide proper ventilation. You cannot mount the DL05 units vertically, upside down, or on a flat horizontal surface. If you place more than one unit in a cabinet, there must be a minimum of 7.2(183mm) between the units.
OK
Installation, Wiring, and Specifications
Airflow
2. Provide a minimum clearance of 2(50mm) between the unit and all sides of the cabinet. Note, remember to allow for any operator panels or other items mounted in the door. 3. There should also be at least 3(78mm) of clearance between the unit and any wiring ducts that run parallel to the terminals.
Temperature Probe
2 50mm min.
BUS Bar
2 50mm min.
2 50mm min.
Panel
Note: there is a minimum of 2(30mm) clearance between the panel door or any devices mounted in the panel door and the nearest DL05 component.
Not to Scale
4. The ground terminal on the DL05 base must be connected to a single point ground. Use copper stranded wire to achieve a low impedance. Copper eye lugs should be crimped and soldered to the ends of the stranded wire to ensure good surface contact. 5. There must be a single point ground (i.e. copper bus bar) for all devices in the panel requiring an earth ground return. The single point of ground must be connected to the panel ground termination. The panel ground termination must be connected to earth ground. Minimum wire sizes, color coding, and general safety practices should comply with appropriate electrical codes and standards for your area.
2-8
Installation, Wiring, and Specifications 6. A good common ground reference (Earth ground) is essential for proper operation of the DL05. One side of all control and power circuits and the ground lead on flexible shielded cable must be properly connected to Earth ground. There are several methods of providing an adequate common ground reference, including: a) Installing a ground rod as close to the panel as possible. b) Connection to incoming power system ground. 7. Evaluate any installations where the ambient temperature may approach the lower or upper limits of the specifications. If you suspect the ambient temperature will not be within the operating specification for the DL05 system, measures such as installing a cooling/heating source must be taken to get the ambient temperature within the range of specifications. 8. The DL05 systems are designed to be powered by 95-240 VAC. Isolation transformers and noise suppression devices are not normally necessary, but may be helpful in eliminating/reducing suspected power problems. NOTE: If you are using other components in your system, make sure you refer to the appropriate manual to determine how those units can affect mounting dimensions.
Agency Approvals Some applications require agency approvals for particular components. The DL05 Micro PLC submission status for agency approval is listed below: S UL (UnderwritersLaboratories, Inc.) pending (1st Qtr., 1999) S CUL (Canadian UnderwritersLaboratories, Inc.) pending (1st Qtr., 1999) S CE (European Economic Union) pending (1st Qtr., 1999) The following table lists the environmental specifications that generally apply to DL05 Micro PLCs. The ranges that vary for the Handheld Programmer are noted at the bottom of this chart. Certain output circuit types may have derating curves, depending on the ambient temperature and the number of outputs ON. Please refer to the appropriate section in this chapter pertaining to your particular DL05 PLC.
Specification Storage temperature Ambient operating temperature* Ambient humidity** Vibration resistance Shock resistance Noise immunity Atmosphere Rating --4F to 158F (--20C to 70C) 32F to 131F (0C to 55C) 5% -- 95% relative humidity (non--condensing) MIL STD 810C, Method 514.2 MIL STD 810C, Method 516.2 NEMA (ICS3--304) No corrosive gases
* Operating temperature for the Handheld Programmer and the DV--1000 is 32to 122F (0to 50C) Storage temperature for the Handheld Programmer and the DV--1000 is --4to 158F (--20to70C). **Equipment will operate down to 5% relative humidity. However, static electricity problems occur much more frequently at low humidity levels (below 30%). Make sure you take adequate precautions when you touch the equipment. Consider using ground straps, anti-static floor coverings, etc. if you use the equipment in low-humidity environments.
2-9
DL05 Micro PLCs can also be secured to a cabinet by using mounting rails. We recommend rails that conform to DIN EN standard 50 022. They are approximately 35mm high, with a depth of 7mm. If you mount the Micro PLC on a rail, do consider using end brackets on each side of the PLC. The end bracket helps keep the PLC from sliding horizontally along the rail, reducing the possibility of accidentally pulling the wiring loose. On the bottom of the PLC is a small retaining clip. To secure the PLC to a DIN rail, place it onto the rail and gently push up on the clip to lock it onto the rail. To remove the PLC, pull down on the retaining clip, lift up on the PLC slightly, then pulling it away from the rail. DIN Rail Dimensions
DIN Rail slot. Use 35mm x 7mm rail conforming to DIN EN 50022.
7mm
35 mm
Retaining Clip NOTE: Refer to our catalog for a complete listing of DINnector connection systems.
2-10
Wiring Guidelines
Power Input Wiring The diagram below shows the external power connection for DL05 Micro PLCs. The terminals can accept up to 16 AWG wire. You may be able to use larger wiring depending on the wire type, but 16 AWG is the recommended size.
110/220 VAC Power Input
LG N 95 -- 240 VAC
NOTE: You can connect either 115 VAC or 220 VAC to the DL05. Special wiring or jumpers are not required as with some of the other DirectLOGIC products. WARNING: Once the power wiring is connected, secure the terminal block cover in the closed position. When the cover is open there is a risk of electrical shock if you accidentally touch the connection terminals or power wiring. Fuse Protection for Input Power There are no internal fuses for the input power circuits, so external circuit protection is needed to ensure the safety of service personnel and the safe operation of the equipment itself. To meet UL/CUL specifications, the input power must be fused. Depending on the type of input power being used, follow these fuse protection recommendations: 208/240 VAC Operation When operating the unit from 208/240 VAC, whether the voltage source is a step-down transformer or from two phases, fuse both the line (L) and neutral (N) leads. The recommended fuse size is 0.375A. 110/125 VAC Operation When operating the unit from 110/125 VAC, it is only necessary to fuse the line (L) lead; it is not necessary to fuse the neutral (N) lead. The recommended fuse size is 0.5A.
2-11
The power source must be capable of suppling voltage and current complying with individual Micro PLC specifications, according to the following specifications:
Item Input Voltage Range Maximum Inrush Current Maximum Power Voltage Withstand (dielectric) Insulation Resistance Specifications 95--240 VAC 13 A, 1ms (95--240 VAC) 15 A, 1ms (240--264 VAC) 30 VA 1 minute @ 1500 VAC between primary, secondary, field ground > 10 MO at 500 VDC
The following guidelines provide general information on how to wire the I/O connections to DL05 Micro PLCs. For specific information on wiring a particular PLC refer to the corresponding specification sheet further in this chapter. 1. Each terminal connection of the DL05 PLC can accept one 16 AWG wire or two 18 AWG size wires. Do not exceed this recommended capacity. 2. Always use a continuous length of wire. Do not splice wires to attain a needed length. 3. Use the shortest possible wire length. 4. Use wire trays for routing where possible. 5. Avoid running wires near high energy wiring. 6. Avoid running input wiring close to output wiring where possible. 7. To minimize voltage drops when wires must run a long distance , consider using multiple wires for the return line. 8. Avoid running DC wiring in close proximity to AC wiring where possible. 9. Avoid creating sharp bends in the wires.
2-12
Installation, Wiring, and Specifications Input and Output circuits on DL05 Micro PLCs do not have internal fuses. In order to protect your Micro PLC, we suggest you add external fuses to your I/O wiring. A fast-blow fuse, with a lower current rating than the I/O bank s common current rating can be wired to each common. Or, a fuse with a rating of slightly less than the maximum current per output point can be added to each output. Refer to the Micro PLC specification sheets further in this chapter to find the maximum current per output point or per output common. Adding the external fuse does not guarantee the prevention of Micro PLC damage, but it will provide added protection.
All DL05 Micro PLCs have a fixed I/O configuration. It follows the same octal numbering system used on other DirectLogic family PLCs, starting at X0 and Y0. The letter X is always used to indicate inputs and the letter Y is always used for outputs. The I/O numbering always starts at zero and does not include the digits 8 or 9. The addresses are typically assigned in groups of 8 or 16, depending on the number of points in an I/O group. For the DL05 the eight inputs use reference numbers X0 -- X7. The six output points use references Y0 -- Y5.
2-13
Field Side
Discrete Inputs
CPU
Output Circuit
Discrete Outputs
Isolation Boundary
Isolation Boundary
The next figure shows the internal layout of DL05 PLCs, as viewed from the front panel.
To Programming Device or Operator Interface
DL05 PLC
CPU
Main Power Supply Input Circuit
Power Input
2 Comm. Ports
Output Circuit
2-14
Installation, Wiring, and Specifications Operator interfaces require data and power connections. Operator interfaces with a large CRT usually require separate AC power. However, small operator interface devices like the popular DV-1000 Data Access Unit and the Optimation panels may be powered directly from the DL05 Micro PLC. Connect the DV-1000 to either communication port on the DL05 Micro PLC using the cable shown below. A single cable contains transmit/receive data wires and +5V power.
DL05 Micro PLC
RJ12 phone style RJ12 phone style
DV-1000
Optimation operator interface panels require separate power and communications connections. Connect the DL05 to the proper D-shell connector on the rear of the Optimation panel using the cable shown below. Optimation panels require 8--30VDC power.
DL05 Micro PLC
RJ12 phone style 15-pin D-shell male
Optimation Panel
DL05 Micro PLCs can be programmed with either a handheld programmer or with DirectSOFT on a PC. Connect the DL05 to a PC using the cable shown below.
DL05 Micro PLC
RJ12 phone style 9-pin D-shell female
The D2-HPP Handheld Programmer comes with a communications cable. For a replacement part, use the cable shown below.
DL05 Micro PLC
RJ12 phone style RJ12 phone style
D2--HPP
(cable comes with HPP) For replacement cable, use part no. DV--1000CBL
2-15
Sinking / Sourcing Before going further in our study of wiring strategies, we must have a solid understanding of sinking and sourcing concepts. Use of these terms occurs Concepts frequently in input or output circuit discussions. It is the goal of this section to make these concepts easy to understand, further ensuring your success in installation. First we give the following short definitions, followed by practical applications.
Sinking = Path to supply ground (-) Sourcing = Path to supply source (+)
First you will notice that these are only associated with DC circuits and not AC, because of the reference to (+) and (--) polarities. Therefore, sinking and sourcing terminology only applies to DC input and output circuits. Input and output points that are either sinking or sourcing can conduct current in only one direction. This means it is possible to connect the external supply and field device to the I/O point with current trying to flow in the wrong direction, and the circuit will not operate. However, we can successfully connect the supply and field device every time by understanding sourcingand sinking . For example, the figure to the right depicts a sinkinginput. To properly connect the external supply, we just have to connect it so the the input provides a path to ground (--). So, we start at the PLC input terminal, follow through the input sensing circuit, exit at the common terminal, and connect the supply (--) to the common terminal. By adding the switch, between the supply (+) and the input, we have completed the circuit. Current flows in the direction of the arrow when the switch is closed.
Input (sinking) + -Common Input Sensing PLC
By applying the circuit principle above to the four possible combinations of input/output sinking/sourcing types, we have the four circuits as shown below. DL05 Micro PLCs provide all except the sourcing output I/O circuit types.
Sinking Input
Input + -Common PLC Input Sensing
Sinking Output
PLC Output Switch Output Load + Common --
Sourcing Input
Common + -Input PLC Input Sensing
Sourcing Output
PLC Output Switch Common + Output Load --
2-16
I/O Common In order for a PLC I/O circuit to operate, Terminal Concepts current must enter at one terminal and exit at another. This means at least two terminals are associated with every I/O point. In the figure to the right, the Input or Output terminal is the main path for the current. One additional terminal must provide the return path to the power supply. If we had unlimited space and budget for I/O terminals, then every I/O point could have two dedicated terminals just as the figure above shows. However, providing this level of flexibility is not practical or even necessary for most applications. So, most Input or Output point groups on PLCs share the return path among two or more I/O points. The figure to the right shows a group (or bank) of 4 input points which share a common return path. In this way, the four inputs require only five terminals instead of eight.
Field Device + --
Return Path
Note: In the circuit above, the current in the common path is 4 times any channel s input current when all inputs are energized. This is especially important in output circuits, where heavier gauge wire is sometimes necessary on commons. Most DL05 input and output circuits are grouped into banks that share a common return path. The best indication of I/O common grouping is on the wiring label. The I/O common grouping bar, labeled at the right, occurs in the section of wiring label below it. It indicates X0, X1, X2, and X3 share the common terminal located to the left of X1. The following complete label shows two banks of four inputs and two banks of three outputs. One common is provided for each bank.
The following label is for DC output versions. One common is provided for all of the outputs and the terminal on the bottom right accepts power for the output stage.
2-17
Connecting DC I/O In the previous section on Sourcing and Sinking concepts, we explained that DC I/O circuits sometimes will only allow current to flow one way. This is also true for many of to Solid State the field devices which have solid-state (transistor) interfaces. In other words, field Field Devices devices can also be sourcing or sinking. When connecting two devices in a series DC circuit, one must be wired as sourcing and the other as sinking. Solid State The DL05 s DC inputs are flexible in that they detect current flow in either direction, Input Sensors so they can be wired as either sourcing or sinking. In the following circuit, a field device has an open-collector NPN transistor output. It sinks current from the PLC input point, which sources current. The power supply can be the FA-24PS +24 VDC power supply or another supply (+12 VDC or +24VDC), as long as the input specifications are met. Installation, Wiring, and Specifications
Field Device Output (sinking) Supply Ground Input (sourcing) PLC DC Input
--
Common
In the next circuit, a field device has an open-emitter PNP transistor output. It sources current to the PLC input point, which sinks the current back to ground. Since the field device is sourcing current, no additional power supply is required.
Field Device +V Input Output (sourcing) Ground (sinking) Common PLC DC Input
Sometimes an application requires connecting a PLC output point to a solid state input on a device. This type of connection is usually made to carry a low-level signal, not to send DC power to an actuator. The DL05 s DC outputs are sinking-only. This means that each DC output provides a path to ground when it is energized. Also, remember that all six outputs have the same electrical common, even though there are two common terminal screws. Finally, recall that the DC output circuit requires power (20 -- 28 VDC) from an external power source. In the following circuit, the PLC output point sinks current to the output common when energized. It is connected to a sourcing input of a field device input.
PLC DC Output +DC pwr Power Input + -(sourcing) 20-28 VDC Ground Field Device +V
2-18
Installation, Wiring, and Specifications In the next example we connect a PLC DC output point to the sinking input of a field device. This is a bit tricky, because both the PLC output and field device input are sinking type. Since the circuit must have one sourcing and one sinking device, we add sourcing capability to the PLC output by using a pull-up resistor. In the circuit below, we connect Rpull-up from the output to the DC output circuit power input.
PLC DC Output +DC pwr Power
R pull-up
(sinking) Output
(sourcing)
R input
Common
NOTE: DO NOT attempt to drive a heavy load (>25 mA) with this pull-up method. NOTE 2: Using the pull-up resistor to implement a sourcing output has the effect of inverting the output point logic. In other words, the field device input is energized when the PLC output is OFF, from a ladder logic point-of-view. Your ladder program must comprehend this and generate an inverted output. Or, you may choose to cancel the effect of the inversion elsewhere, such as in the field device. It is important to choose the correct value of R pull-up. In order to do so, we need to know the nominal input current to the field device (I input) when the input is energized. If this value is not known, it can be calculated as shown (a typical value is 15 mA). Then use I input and the voltage of the external supply to compute R pull-up. Then calculate the power Ppull-up (in watts), in order to size R pull-up properly.
input
input (turn--on)
R pull-up =
-- R input
pull-up
V supply R pullup
The drawing below shows the actual wiring of the DL05 Micro PLC to the supply and pull-up resistor.
2-19
The D0--05AR and the D0--05DR models feature relay outputs. Relays are best for the following applications: S Loads that require higher currents than the solid-state DL05 outputs can deliver S Cost-sensitive applications S Some output channels need isolation from other outputs (such as when some loads require AC while others require DC) Some applications in which NOT to use relays: S Loads that require currents under 10 mA S Loads which must be switched at high speed and duty cycle Assuming relays are right for your application, we re now ready to explore various ways to wire relay outputs to the loads. Note that there are six normally-open SPST relays available. They are organized with three relays per common. The figure below shows the relays and the internal wiring of the PLC. Note that each group is isolated from the other group of outputs.
Y0 Com Y1 Y2 Y3 Y4 Com Y5
In the circuit below, all loads use the same AC power supply which powers the DL05 PLC. In this example, all commons are connected together.
In the circuit on the following page, loads for Y0 -- Y2 use the same AC power supply which powers the DL05 PLC. Loads for Y3 -- Y5 use a separate DC supply. In this example, the commons are separated according to which supply powers the associated load.
2-20
Inductive load devices (devices with a coil) generate transient voltages when de-energized with a relay contact. When a relay contact is closed it bounces , which energizes and de-energizes the coil until the bouncing stops. The transient voltages generated are much larger in amplitude than the supply voltage, especially with a DC supply voltage. When switching a DC-supplied inductive load the full supply voltage is always present when the relay contact opens (or bounces ). When switching an AC-supplied inductive load there is one chance in 60 (60 Hz) or 50 (50 Hz) that the relay contact will open (or bounce ) when the AC sine wave is zero crossing. If the voltage is not zero when the relay contact opens there is energy stored in the inductor that is released when the voltage to the inductor is suddenly removed. This release of energy is the cause of the transient voltages. When inductive load devices (motors, motor starters, interposing relays, solenoids, valves, etc.) are controlled with relay contacts, it is recommended that a surge suppression device be connected directly across the coil of the field device. If the inductive device has plug-type connectors, the suppression device can be installed on the terminal block of the relay output. Transient Voltage Suppressors (TVS or transorb) provide the best surge and transient suppression of AC and DC powered coils, providing the fastest response with the smallest overshoot. Metal Oxide Varistors (MOV) provide the next best surge and transient suppression of AC and DC powered coils. For example, the waveform in the figure below shows the energy released when opening a contact switching a 24 VDC solenoid. Notice the large voltage spike.
+24 VDC
+24 VDC
--24 VDC
2-21
This figure shows the same circuit with a transorb (TVS) across the coil. Notice that the voltage spike is significantly reduced.
+24 VDC +24 VDC --42 VDC Module Relay Contact --24 VDC
Relay contacts wear according to the amount of relay switching, amount of spark created at the time of open or closure, and presence of airborne contaminants. There are some steps you can take to help prolong the life of relay contacts, such as switching the relay on or off only when it is necessary, and if possible, switching the load on or off at a time when it will draw the least current. Also, take measures to suppress inductive voltage spikes from inductive DC loads such as contactors and solenoids. For inductive loads in DC circuits we recommend using a suppression diode as shown in the following diagram (DO NOT use this circuit with an AC power supply). When the load is energized the diode is reverse-biased (high impedance). When the load is turned off, energy stored in its coil is released in the form of a negative-going voltage spike. At this moment the diode is forward-biased (low impedance) and shunts the energy to ground. This protects the relay contacts from the high voltage arc that would occur just as the contacts are opening. Place the diode as close to the inductive field device as possible. Use a diode with a peak inverse voltage rating (PIV) at least 100 PIV, 3A forward current or larger. Use a fast-recovery type (such as Schottky type). DO NOT use a small-signal diode such as 1N914, 1N941, etc. Be sure the diode is in the circuit correctly before operation. If installed backwards, it short-circuits the supply when the relay energizes.
PLC Relay Output Output Supply Common Inductive Field Device
Input
--
Common
2-22
DL05 Micro PLCs with DC inputs are particularly flexible because they can be either sinking or sourcing. The dual diodes (shown to the right) allow current to flow in either direction. The inputs accept 10.8 -- 26.4 VDC. The target applications are +12 VDC and +24 VDC. You can actually wire half of the inputs as DC sinking and the other half as DC sourcing. Inputs grouped by a common must be all sinking or all sourcing.
Common
In the first and simplest example below, all commons are connected together and all inputs are sinking.
-+24 VDC +
In the next example, the first four inputs are sinking, and the last four are sourcing.
+24 VDC
-+
+ --
+12 VDC
2-23
DL05 DC output circuits are high-performance transistor switches with low on-resistance and fast switching times. Please note the following characteristics which are unique to the DC output type: S There is only one electrical common for all six outputs. All six outputs belong to one bank. S The output switches are current-sinking only. However, you can still use different DC voltages from one load to another. S The output circuit inside the PLC requires external power. The supply (--) must be connected to a common terminal, and the supply (+) connects the the right-most terminal on the upper connector. In the example below, all six outputs share a common supply.
+24 VDC
-+
Output Point Wiring
In the next example below, the outputs have splitsupplies. The first three outputs are using a +5 VDC supply, and the last three are using a +24 VDC supply. However, you can split the outputs among any number of supplies, as long as: S all supply voltages are within the specified range S all output points are wired as sinking S all source (--) terminals are connected together
+5 VDC
-+
Output Point Wiring
-+
+24 VDC
2-24
Installation, Wiring, and Specifications DL05 versions with DC type input or output points contain a dedicated High-Speed I/O circuit (HSIO). The circuit configuration is programmable, and it processes select I/O points independently from the CPU scan. Chapter 3 discusses the programming options for HSIO. While the HSIO circuit has six modes, we show wiring diagrams for two of the most popular modes in this chapter. The high-speed input interfaces to points X0 -- X2. Properly configured, the DL05 can count quadrature pulses at up to 5 kHz from an incremental encoder as shown below.
Phase A
12 - 24 VDC
Encoder
DL05 versions with DC type output points can use the High Speed I/O Pulse Output feature. It can generate high-speed pulses for specialized control such as stepper motor / intelligent drive systems. Output Y0 and Y1 can generate pulse and direction signals, or it can generate CCW and CW pulse signals respectively. See Chapter 3 on high-speed input and pulse output options.
+
Signal Common Motor Amplifier
--
+24 VDC
Pulse Direction
Power Input
2-25
Discrete Output
I/O Common
Input Voltage Range Maximum Voltage ON Voltage Level OFF Voltage Level Input Impedance
Maximum OFF Current The maximum current for the input circuit to operate reliably in the OFF state. OFF to ON Response ON to OFF Response Status Indicators The time the module requires to process an OFF to ON state transition. The time the module requires to process an ON to OFF state transition. The LEDs that indicate the ON/OFF status of an input or output point. All LEDs on DL05 Micro PLCs are electrically located on the logic side of the input or output circuit.
2-26
Fuse or C.B.
2A
Y0 - Y5
+V
Common
To LED
The eight AC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has a common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent input circuit shows one channel of a typical bank.
2-27
The six relay output channels use terminals on the right side of the connector. Outputs are organized into two banks of three normally-open relay contacts. Each bank has a common terminal. The wiring example on the last page shows all commons connected together, but separate supplies and common circuits may be used. The equivalent output circuit shows one channel of a typical bank. The relay contacts can switch AC or DC voltages. D0-05AR General Specifications
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge 95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence / print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing) No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum 80 - 132 VAC, 47 - 63 Hz 90 - 120 VAC, 47 -63 Hz 8 mA @ 100 VAC at 50 Hz 10 mA @ 100 VAC at 60 Hz 12 mA @ 132 VAC at 50 Hz 15 mA @ 132 VAC at 60 Hz 14KO @50 Hz, 12KO @60 Hz >6 mA @ 75 VAC <2 mA @ 20 VAC < 40 mS < 40 mS Logic Side 4 channels / common x 2 banks 5- 264 VAC (47 -63 Hz), 5 - 30 VDC 6- 240 VAC (47 -63 Hz), 6 - 27 VDC 2A / point, 6A / common 0.1 mA @264VAC 5 mA @5 VDC < 15 mS < 10 mS Logic Side 3 channels / common x 2 banks None (external recommended)
AC Input Specifications X0 - X7
Input Voltage Range (Min. - Max.) Operating Voltage Range Input Current Max. Input Current Input Impedance ON Current/Voltage OFF Current/Voltage OFF to ON Response ON to OFF Response Status Indicators Commons
Output Voltage Range (Min. - Max.) Operating Voltage Range Output Current Max. leakage current Smallest Recommended Load OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
2-28
D0-05DR These micro PLCs feature eight DC inputs and six relay contact outputs. The I/O Wiring Diagram following diagram shows a typical field wiring example. The AC external power connection uses four terminals at the left as shown.
Fuse or C.B.
+V
+ Common
To LED
The eight DC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has an isolated common terminal, and may be wired as either sinking or sourcing inputs. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent circuit for standard inputs is shown above, and the high-speed input circuit is shown to the left.
The six output channels use terminals on the right side of the connector. Outputs are organized into two banks of three normally-open relay contacts. Each bank has a common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent output circuit shows one channel of a typical bank. The relay contacts can switch AC or DC voltages.
2-29
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge
95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence / print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing) No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum
DC Input Specifications
Parameter
Min. - Max. Voltage Range Operating Voltage Range Peak Voltage Minimum Pulse Width ON Voltage Level OFF Voltage Level Input Impedance Max. Input Current Minimum ON Current Maximum OFF Current OFF to ON Response ON to OFF Response Status Indicators Commons
High-Speed Inputs, X0 - X2
10.8 - 26.4 VDC 12 -24 VDC 30 VDC (5 kHz maximum frequency) 100 s > 10 VDC < 2.0 VDC 1.8 kO @ 12 - 24 VDC 6mA @12VDC 13mA @24VDC >5 mA < 0.5 mA <100 s < 100 s Logic side 4 channels / common x 2 bank
Standard DC Inputs X3 - X7
10.8 - 26.4 VDC 12 -24 VDC 30 VDC N/A > 10 VDC < 2.0 VDC 2.8 kO @ 12 - 24 VDC 4mA @12VDC 8.5mA @24VDC >4 mA <0.5 mA 2- 8 mS, 4 mS typical 2- 8 mS, 4 mS typical Logic side
Output Voltage Range (Min. - Max.) Operating Voltage Output Current Maximum Voltage Max leakage current Smallest Recommended Load OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
5 -264 VAC (47 -63 Hz), 5 - 30 VDC 6 -240 VAC (47 -63 Hz), 6 - 27 VDC 2A / point 6A / common 264 VAC, 30 VDC 0.1 mA @264 VAC 5 mA < 15 mS < 10 mS Logic Side 3 channels / common x 2 banks None (external recommended)
2-30
D0-05AD The D0--05AD Micro PLC features eight AC inputs and six DC outputs. The following I/O Wiring Diagram diagram shows a typical field wiring example. The AC external power connection uses four terminals at the left as shown.
Fuse or C.B.
-+
Input Point Wiring Output Point Wiring
+24 VDC
1A
Y0 - Y5
OUTPUT
Optical Isolator
Common
To LED
0 32
The eight AC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has an isolated common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent input circuit shows one channel of a typical bank. The six current sinking DC output channels use terminals on the right side of the connector. All outputs actually share the same electrical common. Note the requirement for external power on the end (right-most) terminal. The equivalent output circuit shows one channel of the bank of six.
2-31
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge
95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence / print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing) No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum 80 - 132 VAC, 47 - 63 Hz 90 - 120 VAC, 47 - 63 Hz 8 mA @ 100 VAC (50Hz) 10 mA @ 100 VAC (60Hz) 12 mA @ 132 VAC (50Hz) 15 mA @ 132 VAC (60Hz) 14KO @50 Hz, 12KO @60 Hz >6 mA @ 75 VAC <2 mA @ 20 VAC < 40 mS < 40 mS Logic Side 4 channels / common x 2 banks
AC Input Specifications
Input Voltage Range (Min. - Max.) Operating Voltage Range Input Current Max. Input Current Input Impedance ON Current/Voltage OFF Current/Voltage OFF to ON Response ON to OFF Response Status Indicators Commons
DC Output Specifications
Parameter
Min. - Max. Voltage Range Operating Voltage Peak Voltage On Voltage Drop Max Current (resistive) Max leakage current Max inrush current Extenal DC power required OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
Pulse Outputs, Y0 - Y1
5- 30 VDC 6- 27 VDC < 50 VDC (7 kHz max. frequency) 0.3 VDC @ 1A 0.5 A / pt. (1A / point for standard pt.) 15 A @ 30 VDC 2 A for 100 mS 20 - 28 VDC max 150mA <10 S <30 S Logic Side 6 channels / common x 1 banks None
Standard Outputs, Y2 - Y5
5- 30 VDC 6- 27 VDC < 50 VDC 0.3 VDC @ 1A 1.0 A / point 15 A @ 30 VDC 2 A for 100 mS 20 - 28 VDC max 150mA < 10 S < 60 S Logic Side None
2-32
D0-05DD These micro PLCs feature eight DC inputs and six DC outputs. The following I/O Wiring Diagram diagram shows a typical field wiring example. The AC external power connection uses four terminals at the left as shown.
Fuse or C.B.
-+
Input Point Wiring Output Point Wiring
+24 VDC
1A
Y0 - Y5
OUTPUT
Optical Isolator
+ Common
To LED
The eight DC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has an isolated common terminal, and may be wired as either sinking or sourcing inputs. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent circuit for standard inputs is shown above, and the high-speed input circuit is shown to the left.
The six current sinking DC output channels use terminals on the right side of the connector. All outputs actually share the same electrical common. Note the requirement for external power on the end (right-most) terminal. The equivalent output circuit shows one channel of the bank of six.
2-33
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge
95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence / print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing)
No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum High- Speed Inputs, X0 - X2 10.8 - 26.4 VDC 12 - 24 VDC 30 VDC (5 kHz maximum frequency) 100 s > 9.0 VDC < 2.0 VDC 6mA @12VDC, 13mA @24VDC 1.8 kO @ 12 - 24 VDC >5 mA < 0.5 mA <100 S < 100 S Logic side 4 channels / common x 2 banks Standard DC Inputs X3 - X7 10.8 - 26.4 VDC 12 - 24 VDC 30 VDC N/A > 9.0 VDC < 2.0 VDC 4mA @12VDC, 8.5mA @24VDC 2.8 kO @ 12 - 24 VDC >4 mA <0.5 mA 2- 8 mS, 4 mS typical 2- 8 mS, 4 mS typical Logic side
DC Input Specifications
Parameter Min. - Max. Voltage Range Operating Voltage Range Peak Voltage Minimum Pulse Width ON Voltage Level OFF Voltage Level Max. Input Current Input Impedance Minimum ON Current Maximum OFF Current OFF to ON Response ON to OFF Response Status Indicators Commons
DC Output Specifications
Parameter
Min. - Max. Voltage Range Operating Voltage Peak Voltage On Voltage Drop Max Current (resistive) Max leakage current Max inrush current External DC power required OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
Pulse Outputs, Y0 - Y1
5- 30 VDC 6- 27 VDC < 50 VDC (7 kHz max. frequency) 0.3 VDC @ 1 A 0.5 A / pt., 1A / pt. as standard pt. 15 A @ 30 VDC 2 A for 100 mS 20 - 28 VDC < 10 s < 30 s Logic Side 6 channels / common x 1 banks None (external recommended) Max 150mA
Standard Outputs, Y3 - Y5
5- 30 VDC 6- 27 VDC < 50 VDC 0.3 VDC @ 1 A 1.0 A / point 15 A @ 30 VDC 2 A for 100 mS 20 - 28 VDC < 10 s < 60 s Logic Side Max 150mA
2-34
D0-05AA The D0--05AA Micro PLC features eight AC inputs and six AC outputs. The following I/O Wiring Diagram diagram shows a typical field wiring example. The AC external power connection uses four terminals at the left as shown.
Fuse or C.B.
0.5 A
Y0 - Y5
+V
L
OUTPUT
Optical Isolator
COM
6--240 VAC
Line
COM
To LED
The eight AC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has an isolated common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent input circuit shows one channel of a typical bank. The six output channels use terminals on the right side of the connector. Outputs are organized into two banks of three triac switches. Each bank has a common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent output circuit shows one channel of a typical bank.
2-35
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge
95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence / print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing) No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum 80 - 132 VAC, 47 - 63 Hz 90 - 120 VAC, 47 - 63 Hz 8 mA @100 VAC at 50 Hz 10 mA @100 VAC at 60 Hz 12 mA @132 VAC at 50 Hz 15 mA @132 VAC at 60 Hz 14KO @50 Hz, 12KO @60Hz > 6 mA @ 75 VAC < 2 mA @ 20 VAC < 40 mS < 40 mS Logic Side 4 channels / common x 2 banks 15 - 264 VAC, 47 - 63 Hz 17 - 240 VAC, 47 - 63 Hz 1.5 VAC (>50mA) 4.0 VAC (<50mA) 0.5 A / point, 1.5 A / common <4 mA @ 264 VAC 10 A for 10 mS 10 mA 1 mS 1 mS +1/2 cycle Logic Side 3 channels / common x 2 banks None (external recommended)
AC Input Specifications
Input Voltage Range (Min. - Max.) Operating Voltage Range Input Current Max. Input Current Input Impedance ON Current/Voltage OFF Current/Voltage OFF to ON Response ON to OFF Response Status Indicators Commons
AC Output Specifications
Output Voltage Range (Min. - Max.) Operating Voltage On Voltage Drop Max Current Max leakage current Max inrush current Minimum Load OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
2-36
D0-05DA The D0--05DA Micro PLC features eight DC inputs and six AC outputs. The following I/O Wiring Diagram diagram shows a typical field wiring example. The AC external power connection uses four terminals at the left as shown.
Fuse or C.B.
0.5 A
Y0 - Y5
+V
L
OUTPUT
Optical Isolator
+ Common
COM
6--240 VAC
Line
To LED
The eight DC input channels use terminals in the middle of the connector. Inputs are organized into two banks of four. Each bank has an isolated common terminal, and may be wired as sinking or sourcing inputs. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent circuit for standard inputs is shown above, and the high-speed input circuit is shown to the left.
The six output channels use terminals on the right side of the connector. Outputs are organized into two banks of three triac switches. Each bank has a common terminal. The wiring example above shows all commons connected together, but separate supplies and common circuits may be used. The equivalent output circuit shows one channel of a typical bank.
2-37
External Power Requirements Communication Port 1 9600 baud (Fixed), 8 data bits, 1 stop bit, odd parity Communication Port 2 9600 baud (default), 8 data bits, 1 stop bit, odd parity Programming cable type Operating Temperature Storage Temperature Relative Humidity Environmental air Vibration Shock Noise Immunity Terminal Type Wire Gauge
95 - 240 VAC, 30 VA maximum, K-Sequence (Slave) DirectNET (Slave) MODBUS (Slave) K-Sequence (Slave) DirectNET (Master/Slave) MODBUS (Master/Slave) Non-sequence/print D2-DSCBL 32 to 131F (0 to 55_C) -4 to 158F (-20 to 70_C) 5 to 95% (non-condensing) No corrosive gases permitted MIL STD 810C 514.2 MIL STD 810C 516.2 NEMA ICS3-304 Removable One AWG16 or two AWG18, AWG24 minimum
DC Input Specifications
Parameter
Input Voltage Range Operating Voltage Range Maximum Voltage Minimum Pulse Width ON Voltage Level OFF Voltage Level Input Impedance Minimum ON Current Maximum OFF Current OFF to ON Response ON to OFF Response Status Indicators Commons
High-Speed Inputs, X0 - X2
10.8 - 26.4 VDC 12 - 24 VDC 30 VDC (5 kHz maximum frequency) 100 S > 10 VDC < 2.0 VDC 1.8 kO @ 12 - 24 VDC >5 mA < 0.5 mA <100 S < 100 S Logic side 4 channels / common x 2 bank
Standard DC Inputs X3 - X7
10.8 - 26.4 VDC 12 - 24 VDC 30 VDC N/A > 10 VDC < 2.0 VDC 2.8 kO @ 12 - 24 VDC >4 mA <0.5 mA 2- 8 mS, 4 mS typical 2- 8 mS, 4 mS typical Logic side
15 - 264 VAC, 47 - 63 Hz 17 - 240 VAC, 47 - 63 Hz 1.5 VAC @> 50mA, 4 VAC @< 50mA 0.5 A / point, 1.5 A / common < 4 mA @ 264 VAC, 60Hz 10 A for 10 mS 10 mA 1 mS 1 mS +1/2 cycle Logic Side 3 channels / common x 2 banks None (external recommended)
AC Output Specifications
Operating Voltage On Voltage Drop Max Current Max leakage current Max inrush current Minimum Load OFF to ON Response ON to OFF Response Status Indicators Commons Fuses
13
32
Introduction
Built-in Motion Control Solution Many machine control applications require various types of simple high-speed monitoring and control. These applications usually involve some type of motion control, or high-speed interrupts for time-critical events. The DL05 Micro PLC solves this traditionally expensive problem with built-in CPU enhancements. Lets take a closer look at the available high-speed I/O features. The available high-speed input features are: S High Speed Counter (5 kHz max.) with up to 24 counter presets and built-in interrupt subroutine, counts up only, with reset S Quadrature encoder inputs to measure counts and clockwise or counter clockwise direction (5 kHz max.), counts up or down, with reset S High-speed interrupt input for immediate response to critical or time-sensitive tasks S Pulse catch feature to monitor one input point, having a pulse width as small as 100mS (0.1ms) S Programmable discrete filtering (both on and off delay up to 99ms) to ensure input signal integrity (this is the default mode for inputs X0X2) The available pulse output features are: S Single-axis programmable pulse output (7 kHz max.) with three profile types, including trapezoidal moves, registration, and velocity control IMPORTANT: Please note the following restrictions on availability of features: S High-speed input options are available only on DL05s with DC inputs. S Pulse output options are available only on DL05s with DC outputs. S Only one HSIO feature may be in use at one time. You cannot use a highspeed input feature and the pulse output at the same time.
DL05 Part Number D005AR D005DR D005AD D005DD D005AA D005DA Discrete Input Type AC DC AC DC AC DC Discrete Output Type Relay Relay DC DC AC AC High-Speed Input No Yes No Yes No Yes Pulse Output No No Yes Yes No No
33
The internal CPUs main task is to execute the ladder program and read/write all I/O points during each scan. In order to service high-speed I/O events, the DL05 includes a special circuit which is dedicated to a portion of the I/O points. Refer to the DL05 block diagram in the figure below.
6 Discrete Outputs
DL05 PLC
CPU
X3- X7
8 Discrete Inputs
The high-speed I/O circuit (HSIO) is dedicated to the first three inputs (X0 X2) and the first two outputs (Y0 Y1). We might think of this as a CPU helper. In the default operation (called Mode 60) the HSIO circuit just passes through the I/O signals to or from the CPU, so that all eight inputs behave equally and all six outputs behave equally. When the CPU is configured in any other HSIO Mode, the HSIO circuit imposes a specialized function on the portion of inputs and outputs shown. The HSIO circuit operates independently of the CPU program scan. This provides accurate measurement and capturing of high-speed I/O activity while the CPU is busy with ladder program execution. Wiring Diagrams for Each HSIO Mode After choosing the appropriate HSIO mode for your application, youll need to refer to the section in this chapter for that specific mode. Each section includes wiring diagram(s) to help you connect the High-Speed I/O points correctly to field devices. An example of the quadrature counter mode diagram is shown below.
Phase A
12 24 VDC
34
In choosing one of the six high-speed I/O modes, the I/O points listed in the table below operate only as the function listed. If an input point is not specifically used to support a particular mode, it usually operates as a filtered input by default. Similarly, output points operate normally unless Pulse Output mode is selected. Physical I/O Point Usage
DC Input Points Mode High-Speed Counter Quadrature Counter High-Speed Interrupt Pulse Catch Pulse Output X0 Counter clock Phase A Input Interrupt Input Pulse Input Filtered Input X1 Filtered Input Phase B Input Filtered Input Filtered Input Filtered Input X2 Filtered Input or Reset Cnt Filtered Input or Reset Cnt Filtered Input Filtered Input Filtered Input, DC Output Points Y0 Regular Output Regular Output Regular Output Regular Output Pulse or CW Pulse Regular Output Y1 Regular Output Regular Output Regular Output Regular Output Direction or CCW Pulse Regular Output
Filtered Input
Filtered Input
Filtered Input
Filtered Input
Default Mode
Mode 60 (Filtered Inputs) is the default mode. The DL05 is initialized to this mode at the factory, and any time you reset V-memory scratchpad. In the default condition, X0X2 are filtered inputs (10 mS delay) and Y0Y1 are standard outputs.
35
If you have chosen a mode suited to the high-speed I/O needs of your application, were ready to proceed to configure the PLC to operate accordingly. In the block diagram below, notice the V-memory detail in the expanded CPU block. V-memory location V7633 determines the functional mode of the high-speed I/O circuit. This is the most important V-memory configuration value for HSIO functions!
DL05 PLC
Output Circuit
Y0, Y1 Y2 - Y5
CPU
Vmemory V7633
X3- X7
xxxx
Input Circuit
The contents of V7633 is a 16-bit word, to be entered in binarycoded decimal. The figure below defines what each 4-bit BCD digit of the word represents. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
1 5
0 0
Bits 0 7 define the mode number 00, 10.. 60 previously referenced in this chapter. The example data 2050 shown selects Mode 50 Pulse Catch (BCD = 50). The DL05 PLC ignores bits 8 - 15 in V7633. Configuring Inputs X0 X2 In addition to configuring V7633 for the HSIO mode, youll need to program the next three locations in certain modes according to the desired function of input points X0 X2. Other memory locations may require configuring, depending on the HSIO mode (see the corresponding section for particular HSIO modes).
Vmemory Mode X0 X1 X2 V7633 V7634 V7635 V7636 xxxx xxxx xxxx xxxx
36
DL05 PLC
Output Circuit
Y0, Y1 Y2 - Y5
Reset
X2
Mode Select
0010
Input Circuit
Instead of using X2 as a dedicated reset input, you can configure X2 as a normal filtered input. In this way, the counter reset must be generated in ladder logic.
DL05 PLC
Output Circuit
Y0, Y1 Y2 - Y5
Reset
Mode Select
0010
Input Circuit
Next, we will discuss how to program the high-speed counter and its presets.
37
Wiring Diagram
A general wiring diagram for counters/encoders to the DL05 in HSIO Mode 10 is shown below. Many types of pulse-generating devices may be used, such as proximity switches, single-channel encoders, magnetic or optical sensors, etc. Devices with sinking outputs (NPN open collector) are probably the best choice for interfacing. If the counter sources to the inputs, it must output 12 to 24 VDC. Note that devices with 5V sourcing outputs will not work with DL05 inputs.
Signal
Signal Common
The DL05s DC inputs are flexible in that they detect current flow in either direction, so they can be wired to a counter with either sourcing or sinking outputs. In the following circuit, a counter has open-collector NPN transistor outputs. It sinks current from the PLC input point, which sources current. The power supply can be the FA24PS or another supply (+12VDC or +24VDC), as long as the input specifications are met.
Counter Output Output (sinking) 1224 VDC Supply Ground Input (sourcing) X0 Input
Common
In the next circuit, an encoder has open-emitter PNP transistor outputs. It sources current to the PLC input point, which sinks the current back to ground. Since the encoder sources current, no additional power supply is required. However, note that the encoder output must be 12 to 24 volts (5V encoder outputs will not work).
Counter Output +12 to 24VDC Output (sourcing) Ground X0 Input Input (sinking) Common
38
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 10 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
0 1
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor or Data View S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. The goal of counting is to do a special action when the count reaches a preset value. Refer to the figure below. The counter features 24 presets, which you can program. A preset is a number you derive and store so that the counter will constantly compare the current count with the preset. When the two are equal, a special relay contact is energized and program execution jumps to the interrupt routine. We recommend using the special relay(s) in the interrupt service routine to cause any immediate action you desire. After the interrupt service routine is complete, the CPU returns to the ladder program, resuming program execution from the point of interruption. The compare function is ready for the next preset event.
CPU Scan Counter Current Value Input Update Ladder Program Execution Current instruction Output Update INT HSIO Interrupt Routine Program SPxxx IRT
Reset Does Count = Preset? V2320 V2322 V2324 V2326 0000 0000 0000 0000 1000 2000 2500 3175 =
V2376
0921
0000
39
V7630 is a pointer location which points to the beginning of the Preset Data Table. The default starting location for the Preset Data Table is V2320 (default after initializing scratchpad V-memory). However, you may change this by programming a different value in V7630. Use the LDA and OUT instructions as shown:
LDA O2000 OUT V7630
Load the octal address, convert to hex, leave result in accumulator.
Preset Table Pointer V7630 2000 Preset Data V2000 V2002 V2004 V2006 0000 0000 0000 0000 1000 2000 2500 3175
Output this address to V7630, the location of the pointer to the Preset data.
V2076
0000
0000
When using fewer than 24 preset registers, the HSIO looks for 0000 FFFF (use LDD Kffff) in the next preset location to indicate the last preset has been reached. The example to the right uses four presets. The 0000 FFFF in V2331-V2330 indicates the previous preset was the last.
Preset Data V2320 V2322 V2324 V2326 V2330 0000 0000 0000 0000 0000 1000 2000 2500 3175 FFFF
NOTE: Each successive preset must be greater than the previous preset value. If a preset value is less than a lower-numbered preset value, the CPU cannot compare for that value, since the counter can only count upwards. Equal Relay Numbers The following table lists all 24 preset register default locations. Each occupies two 16-bit V-memory registers. The corresponding special relay contact number is in the next column. We might also call these equal relay contacts, because they are true (closed) when the present high-speed counter value is equal to the preset value. Each contact remains closed until the counter value equals the next preset value.
Preset Preset V-memory Register V2321 / V2320 V2323 / V2322 V2325 / V2324 V2327 / V2326 V2331 / V2330 V2333 / V2332 V2335 / V2334 V2337 / V2336 V2341 / V2340 V2343 / V2342 V2345 / V2344 V2347 / V2346 Special Relay Number SP540 SP541 SP542 SP543 SP544 SP545 SP546 SP547 SP550 SP551 SP552 SP553 Preset Preset V-memory Register V2351 / V2350 V2353 / V2352 V2355 / V2354 V2357 / V2356 V2361 / V2360 V2363 / V2362 V2365 / V2364 V2367 / V2366 V2371 / V2370 V2373 / V2372 V2375 / V2374 V2377 / V2376 Special Relay Number SP554 SP555 SP556 SP557 SP560 SP561 SP562 SP563 SP564 SP565 SP566 SP567
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
310
The preset values occupy two data words each. They can range in value from 0000 0000 to 9999 9999, just like the high-speed counter value. All 24 values are absolute values, meaning that each one is an offset from the counter zero value. The preset values must be individually derived for each application. In the industrial lathe diagram below, the PLC monitors the position of the lead screw by counting pulses. At points A, B, and C along the linear travel, the cutter head pushes into the work material and cuts a groove. PLC A Industrial Lathe B C
Counter Device
Motor
Start
The timing diagram below shows the duration of each equal relay contact closure. Each contact remains on until the next one closes. All go off when the counter resets. High-Speed Input and Pulse Output Features Equal Relays
SP540 SP541 SP542
NOTE: Each successive preset must be two numbers greater than the previous preset value. In the industrial lathe example, B>A+1 and C>B+1. X Input Configuration The configurable discrete input options for High-Speed Counter Mode are listed in the table below. Input X0 is dedicated for the counter clock input. Input X1 can be a normal or filtered input. The section on Mode 60 operation at the end of this chapter describes programming the filter time constants. Input X2 can be configured as the counter reset, with or without the interrupt option. The interrupt option allows the reset input (X2) to cause an interrupt like presets do, but there is no SP relay contact closure (instead, X2 will be on during the interrupt routine, for 1 scan). Or finally, X2 may be left simply as a filtered input.
311
Input X0 X1 X2
Function Counter Clock Filtered Input Counter Reset (no interrupt) Counter Reset (with interrupt) FIltered Input 0001
xx06, xx = filter time 0 - 99 ms (BCD) 0007* (default) 0207* 0107* 0307* xx06, xx = filter time 0 - 99 ms (BCD)
*With the counter reset, you have the option of a normal reset or a faster reset. However, the fast reset does not recognize changed preset values during program execution. When 0007 or 0107 are set in V7636 and preset values are changed during program execution, the DL05 recognizes the changed preset values at the time of the reset. When 0207 or 0307 are set in V7636 the CPU does not check for changed preset values, so the DL05 has a faster reset time. High-Speed Input and Pulse Output Features Writing Your Control Program You may recall that the counter instruction is a standard instruction in the DL05 instruction set. Refer to the figure below. The mnemonic for the counter is UDC (up-down counter).The DL05 can have up to 128 counters, labeled CT0 through CT177. The high speed counter in the HSIO circuit is accessed in ladder logic by using UDC CT76. It uses counter registers CT76 and CT77 exclusively when the HSIO mode 10 is active (otherwise, CT76 and CT77 are available for standard counter use). The HSIO counter needs two registers because it is a double-word counter. It has three inputs as shown. The first input (Enable) allows counting when active. The middle input is a dummy and has no fuction other than it is required by the built-in compiler. The bottom signal is the reset. The Dummy Input must be off while the counter is counting. Standard Counter Function
UP Count DOWN Count Reset Input Kxxxxxxxx UDC CTxx
D Counts UP and DOWN D Preload counter by write to value D Reset input is internal only
D Counts UP only D Can use Dummy Input to change count D Reset may be internal or external
312
The next figure shows how the HSIO counter will appear in a ladder program. Note that the Enable Interrupt (ENI) command must execute before the counter value reaches the first preset value. We do this at powerup by using the first scan relay. When using the counter but not the presets and interrupt, we can omit the ENI.
DirectSOFT
SP1 ENI XX Enable Input XX XX Dummy Input Reset Input UDC CT76
Required
Kxxxxxxxx
Preset Range: 1-99999999
When the enable input is energized, the high-speed counter will respond to pulses on X0 and increment the counter at CT76 CT77. The reset input contact behaves in a logical OR fashion with the physical reset input X2 (when selected). So,the high speed counter can receive a reset form either the contact(s) on the reset rung in the ladder, OR the external reset X2 if you have configured X2 as an external reset. Program Example: The following example is the simplest way to use the high-speed counter, which does not use the presets and special relays in the interrupt routine. The program Counter Without configures the HSIO circuit for Mode 10 operation, so X0 is automatically the counter Preset clock input. It uses the Compare-double (CMPD) instruction to cause action at certain count values. Note that this allows you to have more than 24 presets.Then it configures X2 to be the external reset of the counter.
313
DirectSOFT
Mode 10
Configure Inputs
Load the current count of the HSIO counter in V1076 and V1077 into the accumulator Use the Compare-double instruction to compare the double word in the accumulator to the constant K309482 The execution of the above CMPD instruction turns on special relay contact SP62 if the current count is greater than the comparison number (K309482). END coil marks the end of the main program.
SP62
Y0 OUT
END
The compare double instruction above uses the current count of the HSIO counter to turn on Y0. This technique can make more than 24 comparisons, but it is scan-time dependent. However, use the 24 built-in presets with the interrupt routine if your application needs a very fast response time, as shown in the next example.
314
The following example shows how to program the HSIO circuit to trigger on three preset values. You may recall the industrial lathe example from the beginning of this chapter. This example program shows how to control the lathe cutter head to make three grooves in the work-piece at precise positions. When the lead screw turns, the counter device generates pulses which the DL05 can count. The three preset variables A, B, and C represent the positions (number of pulses) corresponding to each of the three grooves.
1500 3780 4850 FFFF
Preset Data
Industrial Lathe A B C
I/O Assignments
X3 X4 Y0 Y1
Cutter head extended Cutter head retracted Lead screw motor Cutter head solenoid
DirectSOFT
SP0
Counter Device
Start
Cutter head
Lead screw
ENI
Enable Interrupts before reaching a preset generates an interrupt. Special Relay SP0 is on during the first CPU scan. Load constant K10 into the accumulator. This selects Mode 10 as the HSIO mode. Output this address to V7633, the location of HSIO Mode select register. Load the constant required to configure X0 as the counter clock. Output the constant K1 to V7634, the location of the setup parameter for X0. Load the constant required to configure X2 as an external reset with interrupt. Output the constant to V7636, the location of the setup parameter for X2. Load the octal address O2320 into the accumulator. This instruction automatically converts the address into hex. Output this address to V7630, the location of the pointer to the Preset Table. Load the preset A value into the accumulator.
SP0
Select Mode 10
SP0
Load Presets
Output the accumulator contents to the memory location for preset 1. Load the preset B value into the accumulator.
315
LDD K4850 OUTD V2324 LDD Kffff OUTD V2326 SP1 UDC SP1 Kxxxxxxxx SP1 SP0 CT76
Output the accumulator contents to the memory location for preset 3. Load the constant Kffff into the accumulator. This value represents the end of the preset list. Output the accumulator contents to the memory location for preset 4 (end of preset marker).
CT76 is the HSIO counter. The first rungs SP1 always enables the counter. The dummy input in the middle is off (unused in this example).
The third rungs Reset input is normally off, because we will use the external reset. You can optionally reset the counter value on each powerup using the SP0 contact.
X3
Y1 RST Y0 SET
Input X3 energizes when the groove has finished cutting. So, we retract the cutter head. Turn lead screw on again, after cutter head has retracted. END coil marks the end of the main program. The INT label marks the beginning of the interrupt service routine program.
X4
Preset 1
Y0 RST
Inside the interrupt service routine, we turn OFF the lead screw motor immediately. These special equal relays turn on individually as the corresponding preset is reached. In this application, each results in the cutting of a groove (Y1), so they are logically ORed together.
SP541
Preset 2
SP542
Y1 SET
Preset 3
X2 C10 SET IRT
Input X2 will be energized inside the interrupt routine if X2 external interrupt was the source. Return from the interrupt service routine.
Some applications will require a different type of action at each preset. It is possible for the interrupt routine to distinguish one preset event from another, by turning on a unique output for each equal relay contact SPxxx. We can determine the source of the interrupt by examining the equal relay contacts individually, as well as X2. The X2 contact will be on (inside the interrupt routine only) if the interrupt was caused by the external reset, X2 input.
316
The following example shows how you can preload the current count with another value. When the preload command input (X4 in this example) is energized, we disable the counter from counting with C0. Then we write the value K3000 to the count register (V1076-V1077). We preload the current count of the counter with K3000. When the preload command (X4) is turned off, the counter resumes counting any pulses, but now starting from K3000.
DirectSOFT
SP0 LD K10 OUT V7633 LD K1 OUT V7634 LD K107 OUT V7636 C0 SET UDC C1 K99999999 C2 SP0 X4
The third rungs Reset input is normally off, because we will use the external reset. You can optionally reset the counter value on each powerup using the SP0 contact. Load constant K10 into the accumulator. This selects Mode 10 as the HSIO mode. Output this address to V7633, the location of HSIO Mode select register. Load the constant required to configure X0 as the counter clock. Output the constant K1 to V7634, the location of the setup parameter for X0. Load the constant required to configure X2 as an external reset with interrupt. Output the constant to V7636, the location of the setup parameter for X2.
Select Mode 10
Set C0 on at powerup to enable counting. CT76 is the HSIO counter. The first rungs C0 contact enables the counter. The dummy input is in the middle.
C0
CT76
When the preload request is made, the user turns on X4. First we disable counting by resetting C0, the counters enable input. Load the BCD value K3000 into the accumulator. Output the constant to V1076/V1077, the location of the accumulated count for CT76. Generate a preload counter input pulse, which causes the counter to preload from V1076-V1077. Enable the counter by setting C0, when the preolad pulse on C1 has occurred (C1 is off). END coil marks the end of the main program.
C0
C1
C0 SET END
317
If youre having trouble with Mode 10 operation, please study the following symptoms and possible causes. The most common problems are listed below.
Symptom: The counter does not count. Possible causes: 1. Field sensor and wiring Verify that the encoder, proximity switch,or counter actually turns on and illuminates the status LED for X0. The problem could be due to sinking-sourcing wiring problem, etc. Remember to check the signal ground connection. Also verify that the pulse on-time is long enough for the PLC to recognize it. 2. Configuration use the Data View window to check the configuration parameters. V7633 must be set to 10, and V7634 must be set to 1 to enable the HSIO counter mode. 3. Stuck in reset check the input status of the reset input, X2. If X2 is on, the counter will not count because it is being held in reset. 4. Ladder program make sure you are using counter CT76 in your program. The top input is the enable signal for the counter. It must be on before the counter will count. The middle input is the dummy input. The bottom input is the counter reset, and must be off during counting. High-Speed Input and Pulse Output Features Symptom: The counter counts but the presets do not function. Possible causes: 1. Configuration Ensure the preset values are correct. The presets are 32-bit BCD values having a range of 0 to 99999999. Make sure you write all 32 bits to the reserved locations by using the LDD and OUTD instructions. Use only evennumbered addresses, from V2320 to V2376. If using less than 24 presets, be sure to place 0000FFFF in the location after the last preset used. 2. Interrupt routine Only use Interrupt #0. Make sure the interrupt has been enabled by executing an ENI instruction prior to needing the interrupt. The interrupt routine must be placed after the main program, using the INT label and ending with an interrupt return IRT. 3. Special relays Check the special relay numbers in your program. Use SP540 for Preset 1, SP541 for Preset 2, etc. Remember that only one special equal relay contact is on at a time. When the counter value reaches the next preset, the SP contact which is on now goes off and the next one turns on. Symptom: The counter counts up but will not reset. Possible causes: 1. Check the LED status indicator for X2 to make sure it is active when you want a reset. Or, if you are using an internal reset, use the status mode of DirectSOFT to monitor the reset input to the counter.
318
DL05 PLC
Output Circuit
Y0, Y1 Y2 - Y5
CPU
Vmemory V7633 0020
Phase Reset B
X1 X2
X3- X7
Input Circuit
Quadrature encoder signals contain position and direction information, while their frequency represents speed of motion. Phase A and B signals shown below are phase-shifted 90 degrees, thus the quadrature name. When the rising edge of Phase A precedes Phase Bs leading edge (indicates clockwise motion by convention), the HSIO counter counts UP. If Phase Bs rising edge precedes Phase As rising edge (indicates counter-clockwise motion), the counter counts DOWN.
Leading Edge Signal 90 phase shift
Clockwise sequence
Phase A Phase B
Counterclockwise sequence
Phase A Phase B Leading Edge Signal one cycle
319
Wiring Diagram
A general wiring diagram for encoders to the DL05 in HSIO Mode 20 is shown below. Encoders with sinking outputs (NPN open collector) are probably the best choice for interfacing. If the encoder sources to the inputs, it must output 12 to 24 VDC. Note that encoders with 5V sourcing outputs will not work with DL05 inputs.
Phase A
12 24 VDC
The DL05s DC inputs are flexible in that they detect current flow in either direction, so they can be wired to an encoder with either sourcing or sinking outputs. In the following circuit, an encoder has open-collector NPN transistor outputs. It sinks current from the PLC input point, which sources current. The power supply can be the +24VDC auxiliary supply or another supply (+12VDC or +24VDC), as long as the input specifications are met.
Encoder Output, (one phase) Output (sinking) 1224 VDC Supply Ground Input (sourcing) Phase A or B Input
Common
In the next circuit, an encoder has open-emitter PNP transistor outputs. It sources current to the PLC input point, which sinks the current back to ground. Since the encoder sources current, no additional power supply is required. However, note that the encoder output must be 12 to 24 volts (5V encoder outputs will not work).
Encoder Output, (one phase) +12 to 24VDC Output (sourcing) Ground Phase A or B Input Input (sinking) Common
320
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 20 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
0 2
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. X Input Configuration The configurable discrete input options for High-Speed Counter Mode are listed in the table below. Input X0 is dedicated for Phase A, and input X1 is for Phase B. Input X2 is the reset input to the quadrature counter, but it does not cause an interrupt. The section on Mode 60 operation at the end of this chapter describes programming the filter time constants. Input X0 Configuration Register V7634 Phase A Function Hex Code Required 0002 (default) quadrature, absolute 0 to 99999999 0012 quadrature, absolute -8388608 to 8388607 X1 X2 V7635 V7636 Phase B Counter Reset (no interrupt) Discrete filtered input 0000 0007 1006
321
You may recall that the Up-Down counter instruction is standard in the DL05 instruction set. Refer to the figure below. The mnemonic for the counter is UDC (up-down counter).The DL05 can have up to 128 counters, labeled CT0 through CT177. The quadrature counter in the HSIO circuit is accessed in ladder logic by using UDC CT76. It uses counter registers CT76 and CT77 exclusively when the HSIO mode 20 is active (otherwise, CT76 and CT77 are available for standard counter use). The HSIO counter needs two registers because it is a double-word counter. It also has three inputs as shown, but they are redefined. The first input is the enable signal, the middle is a preload (write), and the bottom is the reset. The enable input must be on before the counter will count. The enable input must be off during a preload. Standard Counter Function
UP Count DOWN Count Reset Input Kxxxxxxxx UDC CTxx
D Counts UP and DOWN D Preload counter by write to value D Reset input is internal only
D Counts UP and DOWN (from X0, X1) D Can use Dummy Input to change count D Reset may be internal or external
The next figure shows the how the HSIO quadrature counter will appear in a ladder program.
UDC
CT76
Kxxxxxxxx
Preset Range: 1-99999999
When the enable input is energized, the counter will respond to quadrature pulses on X0 and X1, incrementing or decrementing the counter at CT76 CT77. The reset input contact behaves in a logical OR fashion with the physical reset input X2. This means the quadrature counter can receive a reset from either the contact(s) on the reset rung in the ladder, OR the external reset X2. Quadrature Since presets are not available in quadrature counting, this mode is best suited for Counter w/Preload simple counting and measuring. The example program on the following page shows Program Example how to configure the quadrature counter. The program configures the HSIO circuit for Mode 20 operation, so X0 is Phase A and X1 is Phase B clock inputs.
322
DirectSOFT SP0
LD K20 OUT V7633 LD K2 OUT V7634 LD K0 OUT V7635 LD K7 OUT V7636 C0 SET
Load constant K20 into the accumulator. This selects Mode 20 as the HSIO mode. Output this address to V7633, the location of the HSIO Mode select register. Load the constant required to configure X0 as Phase A input. Output the constant to V7634, the location of the setup register for X0. Load the constant required to configure X1 as Phase B input. Output the constant to V7635, the location of the setup register for X1. Load the constant required to configure X2 as an external reset. Output the constant to V7636, the location of the setup register for X2.
Select Mode 20
CT76
CT76 is the HSIO quadrature counter. The first rungs SP1 always enables the counter. The dummy input is used by the built-in compiler.
SP1
Load the current value of the counter into the accumulator on each scan. Compare the value in the accumulator with the constant K44292. If they are equal, the SP61 contact will be turned on.
Select Mode 20
SP61
Set Y0 to ON when the counter reaches our comparison value. END coil marks the end of the main program..
* Note: You can reset Y0 later in the program by using the RST insturuction.
To preload the counter, just add the following example rungs to the program above.
323
X4
When the preload request is made, the user turns on X4. First we disable counting by resetting C0, the counters enable input. Load the BCD value K3000 into the accumulator. Output the constant to V1076/V1077, the location of the accumulated pulse count. Generate a preload counter input pulse, which causes the counter to preload from V1076-V1077. Enable the counter by setting C0, when the preload pulse on C1 has occurred (C1 is off).
Preload counter
C0
C1
C0 SET
If youre having trouble with Mode 20 operation, please study the following symptoms and possible causes. The most common problems are listed below.
Symptom: The counter does not count. Possible causes: 1. Field sensor and wiring Verify that the encoder or other field device inputs actually turn on and illuminates the status LEDs for X0 and X1. A standard incremental encoder will visibly, alternately turn on the LEDs for X0 and X1 when rotating slowly (1 RPM). Or, the problem could be due to a sinking-sourcing wiring problem, etc. Remember to check the signal ground connection. Also verify that the pulse on-time, duty cycle, voltage level, and frequency are within the input specifications. 2. Configuration make sure all of the configuration parameters are correct. V7633 must be set to 20, and V7634 must be set to 0002 to enable the Phase A input, and V7635 must be set to 0000 to enable the Phase B input. 3. Stuck in reset check the input status of the reset input, X2. If X2 is on, the counter will not count because it is being held in reset. 4. Ladder program make sure you are using counter CT76 in your program. The top input is the enable signal for the counter. It must be on before the counter will count. The middle input is the dummy input and must be off for the counter to count. The bottom input is the counter reset, and must be off during counting. Symptom: The counter counts in the wrong direction (up instead of down, and visa-versa). Possible causes: 1. Channel A and B assignment Its possible that Channel A and B assignments of the encoder wires is backwards from the desired rotation/counting orientation. Just swap the X0 and X1 inputs, and the counting direction will be reversed. Symptom: The counter counts up and down but will not reset. Possible causes: 1. Check the LED status indicator for X2 to make sure it is active when you want a reset. Also verify the configuration register V7636 for X2 is set to 7. Or, if you are using an internal reset, use the status mode of DirectSOFT to monitor the reset input to the counter.
324
Trapezoidal Profile
Accel
Decel
Time
Trapezoidal Accel Slope to Target Velocity to Decel Slope Registration Velocity to Position Control on Interrupt (also used for home search moves) S Velocity Control Speed and Direction only The HSIO circuit becomes a high-speed pulse generator (up to 7 kHz) in Mode 30. By programming acceleration and deceleration values, position and velocity target values, the HSIO function automatically calculates the entire motion profile. The figure below shows the DL05 generating pulse and direction signals to the drive amplifier of a stepper positioning system. The pulses accomplish the profile independently and without interruption to ladder program execution in the CPU.
Stepper Motor
Direction
In the figure above, the DL05 generates pulse and direction signals. Each pulse represents the smallest increment of motion to the positioning system (such as one step or micro-step to a stepper system). Alternatively, the HSIO Pulse Output Mode may be configured to deliver counter clock-wise (CCW) and clock-wise (CW) pulse signals as shown to the right.
CCW Pulse
CW Pulse
Drive Amplifier
NOTE: The pulse output is designed for open loop stepper motor systems. This, plus its minimum velocity of 40 pps make it unsuitable for servo motor control.
325
The diagram below shows HSIO functionality in Mode 30. When the lower byte of HSIO Mode register V7633 contains a BCD 30, the pulse output capability in the HSIO circuit is enabled. The pulse outputs use Y0 and Y1 terminals on the output connector. Remember that the outputs can only be DC type to operate.
DL05 PLC
Output Circuit
Y0 (Pulse / CW) Y1 (Direction / CCW) Y2 - Y5
HSIO SP 104 Profile Complete PULSE GEN. Y0 Start Profile Y1 Preload Position Value Interrupt FILTER X1 Filtered Input Mode Select Vmemory V7633 xx30
CPU
X0, X1, X2
X3- X7
Input Circuit
IMPORTANT NOTE: In Pulse Output Mode, Y0 and Y1 references are redefined or are used differently in two ways. Physical references refer to terminal screws, while logical references refer to I/O references in the ladder program. Please read the items below to understand this very crucial point. Notice the I/O point assignment and usage in the above diagram: S X0 and X1 can only be filtered inputs in Pulse Output Mode, and they are available as an input contacts to the ladder program. S X2 behaves as an external interrupt to the pulse generator for registration profiles. In other profile modes, it can be used as a filtered input just like X1 (registration mode configuration shown above). S References Y0 and Y1 are used in two different ways. At the discrete output connector, Y0 and Y1 terminals deliver the pulses to the motion system. The ladder program uses logical references Y0 and Y1 to initiate Start Profile and Load Position Value HSIO functions in Mode 30. Hopefully, the above discussion will explain why some I/O reference names have dual meanings in Pulse Output Mode. Please read the remainder of this section with care, to avoid confusion about which actual I/O function is being discussed.
326
Wiring Diagram
The generalized wiring diagram below shows pulse outputs Y0 and Y1 connected to the drive amplifier inputs of a motion control system.
+
Signal Common Motor Amplifier
+24 VDC
Pulse Direction
The pulse signals from Y0 and Y1 outputs will typically go to drive input circuits as shown above. Remember that the DL05s DC outputs are sinking-only. It will be helpful to locate equivalent circuit schematics of the drive amplifier. The following diagram shows how to interface to a sourcing drive input circuit.
Y0, Y1 Pulse Output Power +DC pwr Output (sinking) Common + Input (sourcing) Ground Drive Input +V
The following circuit shows how to interface to a sinking drive input using a pullup resistor. Please refer to Chapter 2 to learn how to calculate and install Rpullup.
Y0, Y1 Pulse Output +DC pwr Power
R pullup
Drive Input
R input
Common
327
The motion control profiles generated in Pulse Output Mode have the following specifications: Parameter Profiles Specification Trapezoidal Accel Slope / Target Velocity / Decel Slope Registration Velocity to Position Control on Interrupt Velocity Control Speed and Direction only Position Range Positioning Velocity Range V-memory registers Current Position 88388608 to 88388607 Absolute / relative command 40 Hz to 7 kHz V2320 to V2325 (Profile Parameter Table) CT76 and CT77 (V1076 and V1077)
The configurable discrete I/O options for Pulse Output Mode are listed in the table below. The CPU uses SP 104 contact to sense profile complete. V7637 is used to select pulse/direction or CCW/CW modes for the pulse outputs. Input X2 is dedicated as the external interrupt for use in registration mode. Physical Input Configuration Register V7637 Function Y0 = Pulse Y1 = Direction Y0 = CW Pulse Y1 = CCW Pulse X0 X1 X2 V7634 V7635 V7636 Discrete filtered input Discrete filtered input Discrete filtered input 0103 0003 xx06, xx = filter time 0 - 99 ms (BCD) Hex Code Required
The following logical I/O references define functions that allow the HSIO to communicate with the ladder program. Logical I/O SP 104 Y0 Function Profile Complete the HSIO turns on SP104 to the CPU when the profile completes. Goes back off when Start Profile (Y0) turns on. Start Profile the ladder program turns on Y0 to start motion. If turned off before the move completes, motion stops. Turning it on again will start another profile, unless the current position equals the target position. Preload Position Value if motion is stopped and Start Profile is off, you can load a new value in CT76/CT77, and turn on Y1. At that transition, the value in CT76/CT77 becomes the current position.
Y1
328
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 30 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
0 3
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. Profile / Velocity Select Register The first location in the Profile Parameter Table stores two key pieces of information. The upper four bits (1215) select the type of profile required. The lower 12 bits (011) select the Target Velocity. Memory Location V2320 (default)
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
1 7
0 0
0 0
The ladder program must program this location before initiating any of the three profiles. The LD and OUT instruction will write all 16 bits, so be sure to fully specify the full four-digit BCD value for the Position / Velocity Select Register each time. The absolute and relative selection determines how the HSIO circuit will interpret your specified target position. Absolute position targets are referenced to zero. Relative position targets are referenced to the current position (previous target position). You may choose whichever reference method that is most convenient for your application.
329
V7630 is a pointer location which points to the beginning of the Profile Parameter Table. The default starting location for the profile parameter table is V2320. However, you may change this by programming a different value in V7630. Remember to use the LDA (load address) instruction, converting octal into hex. The HSIO uses the next V-memory register past the bottom of the profile parameter table to indicate profile errors. See the error table at the end of this section for error code definitions.
V-Memory V2320, bits 1215 V2320, bits 011 V2321/ 2322 V2323 V2324 V2325 V2326 Function Trapezoidal Profile Target Velocity Value Target Position Value Starting Velocity Acceleration Time Deceleration Time Error Code
Trapezoidal Profile
Range 0=absolute, 8=relative 4 to 700 8388608 to 8388607 4 to 100 1 to 100 1 to 100 (see end of section)
Registration Profile
V-Memory V2320, bits 1215 V2320, bits 011 V2321/ 2322 V2323 V2324 V2325 V2326
Function Registration Profile Target Velocity Value Target Position Value Starting Velocity Acceleration Time Deceleration Time Error Code
Range 9=relative 4 to 700 8388608 to 8388607 4 to 100 1 to 100 1 to 100 (see end of section)
Velocity Profile
330
Pulse Output Mode generates three types of motion profiles. Most applications use one type for most moves. However, each move can be different if required. S Trapezoidal Accel Slope to Target Velocity to Decel Slope S Registration Velocity to Position Control on Interrupt S Velocity Control Speed and Direction only The trapezoidal profile is the most Trapezoidal Profile common positioning profile. It moves the Velocity load to a pre-defined target position by Fixed Velocity creating a move profile. The acceleration slope is applied at the starting position. Accel Decel The deceleration slope is applied backwards from the target position. The remainder of the move in the middle is Time spent traveling at a defined velocity. Start position Target position Trapezoidal profiles are best for simple point-to-point moves, when the distance between the starting and ending positions of the move is known in advance.
Registration profiles solve a class of motion control problems. In some applications, product material in work Scrap moves past a work tool such as a drill Finished part area Area station. Shown to the right, registration marks on the scrap area of the work-piece allow a machine tool to register its position relative to the rectangle, to drill properly. Home search moves allow open-loop direction of motion motion systems to re-calibrate (preload) Registration marks the current position value at powerup. Registration profiles are a combination of Registration Profile velocity and position control modes. The Velocity Position move begins by accelerating to a Control Control programmed velocity. The velocity is Velocity sustained and the move is of indefinite duration. When an external interrupt Accel Decel signal occurs (due to registration sensing), the profile switches from velocity to position control. The move ends by continuing motion a pre-defined distance past the interrupt point (such as a drill hole Target position location). The deceleration ramp is applied in advance of the target position. Interrupt The velocity profile controls only the direction and speed of motion. There is no target position specified, so the move can be of indefinite length. Only the first velocity value needs to be defined. The remaining velocity values can be created while motion in in progress. Arrows in the profile shown indicate velocity changes.
Velocity
Velocity Profile
Time
331
SP104
The time line of signal traces below the profile indicates the order of events. The HSIO uses logical output Y0 as the Start input to the HSIO, which starts the profile. Immediately the HSIO turns off the Profile Complete signal (SP104), so the ladder program can monitor the progress of the move. Typically a ladder program will monitor this bit so it knows when to initiate the next profile move. If you are familiar with motion control, youll notice that we do not have to specify the direction of the move. The HSIO function examines the target position relative to the current position, and automatically outputs the correct direction information to the motor drive. Notice that the motion accelerates immediately to the starting velocity. This segment is useful in stepper systems so we can jump past low speed areas when low-torque problems or a resonant point in the motor might cause a stall. (When a stepper motor stalls, we have lost the position of the load in open-loop positioning systems). However, is is preferable not to make the starting velocity too large, because the stepper motor will also slip some pulses due to the inertia of the system. When you need to change the current position value, use logical Y1 output coil to load a new value into the HSIO counter. If the ladder program loads a new value in CT76/CT77 (V1076/V1077), then energizing Y1 will copy that value into the HSIO circuit counter. This must occur before the profile begins, because the HSIO ignores Y1 during motion.
332
Trapezoidal Profile The trapezoidal profile we want to perform is drawn and labeled in the following Program Example figure. It consists of a non-zero starting velocity, and moderate target velocity. Trapezoidal Profile
Velocity Target Velocity = 1 kHz Accel = 2 sec Starting Velocity = 40 Time Start position Target position = 5000 Decel = 4 sec
The following program will realize the profile drawn above, when executed. The beginning of the program contains all the necessary setup parameters for Pulse Output Mode 30. We only have to do this once in the program, so we use first-scan contact SP0 to trigger the setup.
DirectSOFT
SP0
Load constant K30 into the accumulator. This selects Mode 30 as the HSIO mode. Output the constant to V7633, the location of the HSIO Mode select register. Load the octal address of the beginning of the Profile Parameter Table. The LDA instruction converts this to a hex number in the accumulator. Output this address to V7630, the location of the pointer to the Profile Parameter Table. Load the constant K103 which is required to select pulse and direction for physical Y0 and Y1 functions, respectively (use K3 if your application needs CCW and CW). Output this constant to V7634, configuring the pulse output type. Load the constant K1006 which is required to select filtered inputs with a 10 mS filter time constant. Output this constant to V7635, configuring X1.
Mode 30
Filtered Inputs
333
SP0
Load the constant K100 which is required to select Trapzoidal Profile, absolute positioning, and a target velocity of 1 kHz. Output this constant to V2320, the location of the Profile Select / Starting Velocity setup register. Load the constant K5000 which selects a target position of 5000 pulses. Dont forget to use double word size (8-digit BCD position value). Output this constant to V2321 and V2322, the location of the Target Position double-word register. Load the constant K4 which is required to select a starting velocity of 40 Hz (4 x 10 pps). Output this constant to V2323, the location of the starting velocity parameter register. Load the constant K20 which is required to select an acceleration time of 2 seconds (20 x 100 mS). Output this constant to V2324, the location of the acceleration parameter register. Load the constant K40 which is required to select a deceleration time of 4 seconds (40 x 100 mS). Output this constant to V2325, the location of the deceleration parameter register. We use a spare filtered input to allow the operator to start the profile. When the operator turns X3 ON, then OFF, logical output Y0 starts the profile. SP104 is the logical output of the HSIO to indicate the move is complete. We use Y2 to energize an annunciator that the profile has finished.
Starting Velocity
LD K4 OUT V2323
Acceleration
Deceleration
Start Profile
X3
Profile Complete
SP 104
At any time you can write (preload) a new position into the current position value. This often done after a home search (see the registration example programs).
SP0
Load the constant K1000 as the new current position value. Output this constant to V1076/V1077 (CTA76/CTA77). the location of the current position value.
Turn on Y1 for 1 scan. The off-to-on transition causes the HSIO to preload the current position with the value in
334
1.
Scrap Area
2. In other examples of registration, the work piece is stationary and the tool moves. A drill bit may approach the surface of a part in work, preparing to drill a hole of precise depth. However, the drill bit length gradually decreases due to tool wear. A method to overcome this is to detect the moment of contact with the part surface on each drill, moving the bit into the part a constant distance after contact.
High-Speed Input and Pulse Output Features
direction of motion
Registration marks
Detect contact
3.
The home search move allows a motion system to calibrate its position on startup. In this case, the positioning system makes an indefinite move and waits for the load to pass by a home limit switch. This creates an interrupt at the moment when the load is in a known position. We then stop motion and preload the position value with a number which equates to the physical home position. The registration profile begins with only velocity control. When an interrupt pulse occurs on physical input X2, the starting position is declared to be the present count (current load position). The velocity control switches to position control, moving the load to the target position. Note that the minimum starting velocity is 40 pps. This instantaneous velocity accommodates stepper motors that can stall at low speeds.
Velocity
Registration Profile
Target Velocity Accel Decel
The time line of signal traces below the profile indicates the order of events. The CPU uses logical output Y0 to start the profile. Immediately the HSIO turns off the Profile Complete signal (SP104), so the ladder program can monitor the moves completion by sensing the signals on state.
335
Registration Profile The registration profile we want to perform is drawn and labeled in the following Program Example figure. It consists of a non-zero starting velocity, and moderate target velocity. Registration Profile
Velocity Target Velocity = 1 kHz Accel = 2 sec Starting Velocity = 40 Time Start position Target position = 5000 Decel = 4 sec
The following program will realize the profile drawn above, when executed. The first program rung contains all the necessary setup parameters. We only have to do this once in the program, so we use first-scan contact SP0 to trigger the setup.
DirectSOFT
SP0 LD K30 OUT V7633 LDA O2320 OUT V7630
Load constant K30 into the accumulator. This selects Mode 30 as the HSIO mode. Output this constant to V7633, the location of the HSIO Mode select register. Load the octal address of the beginning of the Profile Parameter Table. The LDA instruction converts this to a hex number in the accumulator. Output this address to V7630, the location of the pointer to the Profile Parameter Table. Load the constant K103 which is required to select pulse and direction for physical Y0 and Y1 functions, respectively (your application may use CCW and CW). Output this constant to V7634, configuring the pulse output type. Load the constant K2006 which is required to select X1 as a filtered input with a 20 mS filter time constant. Output this constant to V7635, configuring X1.
Filtered Inputs
Load the constant K1006 which is required to select the external interrupt. Output this constant to V7636, configuring X2, the registration interrupt input.
336
Starting Velocity
LD K4 OUT V2323
Acceleration
Deceleration
Start Profile
X3 Y0 SET
We use an input to allow the operator to start the profile. X3 is a momentary Start switch. When the operator turns X3 ON, logical output Y0 starts the profile. SP104 is the logical output of the HSIO to indicate the move is complete. We use Y2 to energize an annunciator that the profile has finished. This wont occur until after the interrupt from X2 has occurred and the profile is complete.
Profile Complete
SP104 Y2 OUT C0 PD C0 Y0 RST
The profile will begin when the start input (X3) is given. Then the motion begins an indefinite move, which lasts until an external interrupt on X2 occurs. Then the motion continues on for 5000 more pulses before stopping.
337
One of the more challenging aspects of motion control is the establishment of actual position at powerup. This is especially true for open-loop systems which do not have a position feedback device. However, a simple limit switch located at an exact location on the positioning mechanism can provide position feedback at one point. For most stepper control systems, this method is a good and economical solution.
Load Positioning System Motor
CW limit (X3)
-3000
-2000
-1000
1000
2000
3000
In the drawing above, the load moves left or right depending on the CCW/CW direction of motor rotation. The PLC ladder program senses the CCW and CW limit switches to stop the motor, before the load moves out-of-bounds and damages the machine. The home limit switch is used at powerup to establish the actual position. The numbering system is arbitrary, depending on a machines engineering units. At powerup, we do not know whether the load is located to the left or to the right of the home limit switch. Therefore, we will initiate a home search profile, using the registration mode. The home limit switch is wired to X2, causing the interrupt. We choose an arbitrary initial search direction, moving in the CW (left-to-right) direction. S If the home limit switch closes first, then we stop and initialize the position (this value is typically 0, but it may be different if preferred). S However, if the CW limit switch closes first, we must reverse the motor and move until the home limit switch closes, stopping just past it. In the latter case, we repeat the first move, because we always need to make the final approach to the home limit switch from the same direction, so that the final physical position is the same in either case!
DirectSOFT
SP0 LD K30 OUT V7633 LDA O2320 OUT V7630
Configure the address of the parameter table. Selects Mode 30 as the HSIO mode.
Filtered Inputs
LD K2006 OUT V7635 OUT V7637
The constant K2006 selects a 20 mS filter time constant. Output this constant to V7635, configuring X1. Output this constant to V7637, configuring X3. The constant K1006 selects a 10 mS filter time constant. Output this constant to V7636, configuring X2, the registration interrupt input.
Configure the Y0 and Y1 pulse outputs for pulse and direction, respectively.
338
C1
T0
The constant K4 selects a starting velocity of 40 Hz (4 x 10 pps).
Starting Velocity
LD K4 OUT V2323
C3
X2
CCW past home Load a small positive position count (go CW).
Acceleration
Deceleration
OUT V2325 X10
C10 SET
Search in CW direction
C10 C0 LDD K50 OUTD V2321 Y0 SET C0 SET
Turn on Start Profile, searching for either the home limit or the CW limit (depends on our starting position). Set C0 to indicate the CW home search has begun. The constant K50 selects a target position of 50 pulses (CW direction).
C4
Target Position
T1
CW delay done.
CW Limit found
C0 C1 X3 Y0 RST LDD K80000200 OUTD V2321 C1 SET
Turn off Start Profile. The constant K200 selects a target position of 200 pulses, which is in the CCW direction.
C5
The home search profile will execute specific parts of the program, based on the order of detection of the limit switches. Ladder logic sets C0 to initiate a home search in the CW direction. If the CW limit is encountered, the program searches for home in the CCW direction, passes it slightly, and does the final CW search for home. After reaching home, the last ladder rung preloads the current position to 0.
339
The time line of signal traces below the profile indicates the order of events. Assuming the velocity is set greater than zero, motion begins when the Start input (Y0) energizes. Since there is no end position target, the profile is considered in progress as long as the Start input remains active. The profile complete logical input to ladder logic (X0) correlates directly to the Start input status when velocity profiles are in use. While the Start input is active, the ladder program can command a velocity change by writing a new value to the velocity register (V2323 by default). The full speed range of 40 Hz to 7 kHz is available. Notice from the drawing that there are no acceleration or deceleration ramps between velocity updates. This is how velocity profiling works with the HSIO. However, the ladder program can command more gradual velocity changes by incrementing or decrementing the velocity value more slowly. A counter or timer can be useful in creating your own acceleration/deceleration ramps. Unless the load must do a very complex move, it is easier to let the HSIO function generate the accel/decel ramps by selecting the trapezoidal or registration profiles instead. Unlike the trapezoidal and registration profiles, you must specify the desired direction of travel with velocity profiles. Load the direction select register (V2321/V2322 by default) with 8000 0000 hex for CCW direction, or 0 for CW direction.
340
The velocity profile we want to perform is drawn and labeled in the following figure. Each velocity segment is of indefinite length. The velocity only changes when ladder logic (or other device writing to V-memory) updates the velocity parameter. Velocity Profile
Velocity
Time
The following program uses dedicated discrete inputs to load in new velocity values. This is a fun program to try, because you can create an infinite variety of profiles with just two or three input switches. The intent is to turn on only one of X1, X2, or X3 at a time. The beginning of the program contains all the necessary setup parameters for Pulse Output Mode 30. We only have to do this once in the program, so we use first-scan contact SP0 to trigger the setup. High-Speed Input and Pulse Output Features
DirectSOFT
SP0 LD K30 OUT V7633 LDA O2320 OUT V7630
Load constant K30 into the accumulator. This selects Mode 30 as the HSIO mode. Output this constant to V7633, the location of the HSIO Mode select register. Load the octal address of the beginning of the Profile Parameter Table. The LDA instruction converts this to hex number in the accumulator. Output this address to V7630, the location of the pointer to the Profile Parameter Table. Load the constant K103 which is required to select pulse and direction for physical Y0 and Y1 functions, respectively (your application may use CCW and CW). Output this constant to V7634, configuring the pulse output type. Load the constant K1006 which is required to select filtered inputs with a 10 mS filter time constant. Output this constant to V7635, configuring X1.
Mode 30
Filtered Inputs
341
Set Velocity
Start Profile
X1 Y0 OUT
We use a spare filtered input to allow the operator to start the profile. When the operator turns X1 ON and leaves it on, logical output Y0 starts the profile. Load the constant K50 which is required to select a velocity of 500 pps when the operator closes X2. Output this constant to V2323, the location of the velocity parameter register. The speed will change immediately.
Go Slow
X2 LD K50 OUT V2323
Go Moderately
X3 LD K200 OUT V2323 LD K600 OUT V2323
Load the constant K200 which is required to select a velocity of 2000 pps when the operator closes X3. Output this constant to V2323, the location of the velocity parameter register. The speed will change immediately. Load the constant K600 which is required to select a velocity of 6000 pps when the operator closes X4. Output this constant to V2323, the location of the velocity parameter register. The speed will change immediately.
Go Fast
X4
342
Pulse Output Error The Profile Parameter Table starting at V2320 (default location) defines the profile. Certain numbers will result in a error when the HSIO attempts to use the parameters Codes to execute a move profile. When an error occurs, the HSIO writes an error code in V2326. Error Code 0000 0010 0020 0021 0022 0030 0040 0041 0042 0050 High-Speed Input and Pulse Output Features 0051 0052 0060 0061 0062 No error Requested profile type code is invalid (must use 0, 1, 2, 8, or 9) Target Velocity is not in BCD Target Velocity is specified to be less than 40 pps Target Velocity is specified to be greater than 7,000 pps Target Position value is not in BCD Starting Velocity is not in BCD Starting Velocity is specified to be less than 40 pps Starting Velocity is specified to be greater than 1,000 pps Acceleration Time is not in BCD Acceleration Time is zero Acceleration Time is greater than 10 seconds Deceleration Time is not in BCD Deceleration Time is zero Deceleration Time is greater than 10 seconds Error Description
Most errors can be corrected by rechecking the Profile Parameter Table values. The error is automatically cleared at powerup and at Program-to-Run Mode transitions. Troubleshooting Guide for Mode 30 If youre having trouble with Mode 30 operation, please study the following symptoms and possible causes. The most common problems are listed below:
Symptom: The stepper motor does not rotate. Possible causes: 1. Configuration Verify that the HSIO actually generates pulses on outputs Y0 and Y1. Watch the status LEDs for Y0 and Y1 when you start a motion profile. If the LEDs flicker on and off or are steadily on, the configuration is probably correct. 2. Programming error If there are no pulses on Y0 or Y1 you may have a programming error. Check the contents of V2326 for an error code that may be generated when the PLC attempts to do the move profile. Error code descriptions are given above. 3. Check target value The profile will not pulse if the count value is equal to the target value (ex. count =0, target=0)
343
4. Wiring Verify the wiring to the stepper motor is correct. Remember the signal ground connection from the PLC to the motion system is required. 5. Motion system Verify that the drive is powered and enabled. To verify the motion system is working, you can use Mode 60 operation (normal PLC inputs/outputs) as shown in the test program below. With it, you can manually control Y0 and Y1 with X0 and X1, respectively. Using an input simulator is ideal for this type of manual debugging. With the switches you can single-step the motor in either direction. If the motor will not move with this simple control, Mode 30 operation will not be possible until the problem with the motor drive system or wiring is corrected.
DirectSOFT
SP0 LD K60 OUT V7633 LD K1006 OUT V7634 OUT V7635 OUT V7636 X0 Y0 OUT Y1 OUT END
Load constant K60 into the accumulator. This selects Mode 60 as the HSIO mode. Output the constant to V7633, the location of the HSIO Mode select register. Load the constant K1006 which is required to configure filtered inputs with a time constant of 10 mS. Output this constant to V7634, configuring X0.
X1
Use a switch on X1 input to manually control output Y1. END coil marks the end of the main program..
6. Memory Error HSIO configuration parameters are stored in the CPU system memory. Corrupted data in this memory area can sometimes interfere with proper HSIO operation. If all other corrective actions fail, initializing the scratchpad memory may solve the problem. With DirectSOFT, select the PLC menu, then Setup, then Initialize Scratchpad. Symptom: The motor turns in the wrong direction. Possible causes: 1. Wiring If you have selected CW and CCW type operation, just swap the wires on Y0 and Y1 outputs. 2. Direction control If you have selected Pulse and Direction type operation, just change the direction bit to the opposite state.
344
DL05 PLC
Y0, Y1
Output Circuit
Y2 - Y5
HSIO
Interrupt FILTER
X0 X1, X2
CPU
Vmemory V7633
X3- X7
0040
Input Circuit
Alternately, you may configure the HSIO circuit to generate interrupts based on a timer, as shown below. In this configuration, inputs X0 through X2 are filtered inputs.
DL05 PLC
Output Circuit
Y0, Y1 Y2 - Y5
CPU
Vmemory V7633
X3- X7
0040
X0, X1, X2
Input Circuit
345
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 40 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
1 4
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. Refer to the drawing below. The source of the interrupt may be external (X0), or the HSIO timer function. The setup parameter in V7634 serves a dual purpose:, S It selects between the two interrupt sources, external (X0) or an internal timer. S In the case of the timer interrupt, it programs the interrupt timebase between 5 and 999 mS. The resulting interrupt uses label INT 0 in the ladder program. Be sure to include the Enable Interrupt (ENI) instruction at the beginning of your program. Otherwise, the interrupt routine will not be executed.
CPU Scan Input Update Ladder Program Execution current instruction Input Update INT Interrupt Routine Program IRT
346
External Interrupt Signal pulses at X0 must meet certain timing criteria to guarantee an interrupt will Timing Parameters result. Refer to the timing diagram below. The input characteristics of X0 are fixed (it is not a programmable filtered input). The minimum pulse width is 0.1 mS. There must be some delay before the next interrupt pulse arrives, such that the interrupt period cannot be smaller than 0.5 mS.
0.5 mS minimum 0.1 mS minimum External Interrupt X0 Time
When the timed interrupt is selected, the HSIO generates the interrupt to ladder logic. There is no interrupt pulse width in this case, but the interrupt period can be adjusted from 5 to 999 mS.
5 mS to 999 mS Timed Interrupt Time
The configurable discrete input options for High-Speed Interrupt Mode are listed in the table below. Input X0 is the external interrupt when 0004 is in V7634. If you need a timed interrupt instead, then V7634 contains the interrupt time period, and input X0 becomes a filtered input (uses X1s filter time constant by default). Inputs X1, and X2, can only be filtered inputs, having individual configuration registers and filter time constants. However, X0 will have the same filter time constant as X1 when the timed interrupt is selected. Input X0 Configuration Register V7634 Function External Interrupt Hex Code Required 0004 (default) xxx4, xxx = INT timebase 5 - 999 ms (BCD) xx06 (xx = filter time) 0 - 99 ms (BCD) xx06 (xx = filter time) 0 - 99 ms (BCD)
Uses X1s time Filtered Input (when setting in V7635 timed interrupt is in use) X1 X2 V7635 V7636 Filtered Input Filtered Input
Independent Timed Interrupt O1 is also available as an interrupt. This interrupt is independent of the HSIO features. Interrupt O1 uses an internal timer that is configured in V memory Interrupt location V7647. The interrupt period can be adjusted from 5 to 9999 mS. Once the interrupt period is set and the interrupt is enabled in the program, the CPU will continuously call the interrupt routine based on the time setting in V7647. Input Configuration Register V7647 Function High-Speed Timed Interrupt Hex Code Required xxxx (xxxx = timer setting) 5 - 9999 mS (BCD)
347
The following program selects Mode 40, then selects the external interrupt option. Inputs X1 and X2 are configured as filtered inputs with a 10 mS time constant. The program is otherwise generic, and may be adapted to your application.
DirectSOFT
SP0 LD K40 OUT V7633 LD K4 OUT V7634
Load constant K40 into the accumulator. This selects Mode 40 as the HSIO mode. Output this constant to V7633, the location of the HSIO Mode select register. Load the constant K4 which is required to select the external interrupt option. X0 is the interrupt input. Output this constant to V7634, configuring the external interrupt option for X0. Load the constant K1006 which is required to select filtered inputs with a 10 mS filter time constant. Output this constant to V7635, configuring X1.
Filtered Inputs
Reset output Y0. Enable Interrupts at the beginning of the program. Insert Main Program rungs here for your application.
ENI
END INT O0
END coil marks the end of the main program.. The INT label marks the beginning of the interrupt service routine program. Insert interrupt service routine rungs here for your application.
Interrupt Routine
SP1 Y5 SET IRT
348
The following program selects Mode 40, then selects the timed interrupt option, with an interrupt period of 100 mS.
100 mS Timed Interrupt Time
Inputs X0, X1, and X2, are configured as filtered inputs with a 10 mS time constant. Note that X0 uses the time constant from X1. The program is otherwise generic, and may be adapted to your application.
DirectSOFT
SP0 LD K40 OUT V7633 LD K1004 OUT V7634
Load constant K40 into the accumulator. This selects Mode 40 as the HSIO mode. Output this constant to V7633, the location of the HSIO Mode select register. Load the constant K1004 which is required to select the timed interrrupt option, with a period of 100 mS. Output this constant to V7634, configuring the timed interrupt for 100 mS period. Load the constant K1006 which is required to select filtered inputs with a 10 mS filter time constant. Output this constant to V7635, configuring X1 and X0
Filtered Inputs
INT Enable
ENI
Enable Interrupts at the beginning of the program. Insert Main Program rungs here for your application.
Main Program
END INT O0
END coil marks the end of the main program.. The INT label marks the beginning of the interrupt service routine program. Insert interrupt service routine rungs here for your application.
Interrupt Routine
SP1 LD K1 ADD V2000 OUT V2000 IRT
Add the value in the accumulator with the value in memory location V2000. Output the result into memory location V2000.
349
DL05 PLC
Y0, Y1
Output Circuit
Y2 - Y5
CPU
Vmemory V7633
X3- X7
Reset scan
Mode Select
0050
Input Circuit
Signal pulses at X0 must meet certain timing criteria to guarantee a pulse capture Pulse Catch Timing Parameters will result. Refer to the timing diagram below. The input characteristics of X0 are fixed (it is not a programmable filtered input). The minimum pulse width is 0.1 mS. There must be some delay before the next pulse arrives, such that the pulse period cannot be smaller than 0.5 mS. If the pulse period is smaller than 0.5 mS, the next pulse will be considered part of the current pulse.
0.5 mS minimum 0.1 mS minimum Pulse Input X0 Time
Note that the pulse catch and filtered input functions are opposite in nature. The pulse catch feature on X0 seeks to capture narrow pulses, while the filter input feature on X1 and X2 seeks to reject narrow pulses.
350
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 50 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
1 5
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. X Input Configuration The configurable discrete input options for Pulse Catch Mode are listed in the table below. Input X0 is the pulse input, and must have 0005 loaded into it configuration register V7634. Inputs X1 and X2 can only be filtered inputs. Each input has its own configuration register and filter time constant. Input X0 X1 X2 Configuration Register V7634 V7635 V7636 Function Pulse Catch Input Filtered Input Filtered Input 0005 xx06 (xx = filter time) 0 - 99 ms (BCD) xx06 (xx = filter time) 0 - 99 ms (BCD) Hex Code Required
351
The following program selects Mode 50, then programs the pulse catch code for X0. Inputs X1 and X2 are configured as filtered inputs with 10 and 30 mS time constants respectively. The program is otherwise generic, and may be adapted to your application.
DirectSOFT
SP0 LD K50 OUT V7633 LD K5 OUT V7634
Load constant K50 into the accumulator. This selects Mode 50 as the HSIO mode. Output this constant to V7633, the location of the HSIO Mode select register. Load the constant K5 which is required to configure X0 as the pulse catch input. Output this constant to V7634, configuring the pulse catch option for X0. Load the constant K1006 which is required to select filtered inputs with a 10 mS filter time constant. Output this constant to V7635, configuring X1.
Filtered Inputs
Load the constant K3006 which is required to select filtered inputs with a 30 mS filter time constant. Output this constant to V7636, configuring X2.
Main Program
SP100 Y0 SET END
Use the pulse catch input to set output Y0 on. This will work even for a very short pulse on X0. END coil marks the end of the main program..
352
DL05 PLC
Y0, Y1
Output Circuit
Y2 - Y5
HSIO
CPU
Vmemory V7633
X3- X7
FILTERS
0060
X0
X1
X2
Input Circuit
Input Filter Signal pulses at inputs X0 X2 are filtered by using a delay time. In the figure below, Timing Parameters the input pulse on the top line is longer than the filter time. The resultant logical input to ladder is phase-shifted (delayed) by the filter time on both rising and falling edges. In the bottom waveforms, the physical input pulse width is smaller than the filter time. In this case, the logical input to the ladder program remains in the OFF state (input pulse was filtered out).
Filter Time Physical Input Logical Input X0 X0 Time Physical Input Logical Input X0 X0 Filter Time
353
Recall that V7633 is the HSIO Mode Select register. Refer to the diagram below. Use BCD 60 in the lower byte of V7633 to select the High-Speed Counter Mode. The DL05 does not use bits 8 - 15 in V7633. Memory Location V7633
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
0 0
1 6
0 0
Choose the most convenient method of programming V7633 from the following: S Include load and out instructions in your ladder program S DirectSOFTs memory editor S Use the Handheld Programmer D2HPP We recommend using the first method above so that the HSIO setup becomes an integral part of your application program. An example program later in this section shows how to to this. X Input Configuration The configurable discrete input options for Discrete Filtered Inputs Mode are listed in the table below. The filter time constant (delay) is programmable from 0 to 99 mS (the input acts as a normal discrete input when the time constant is set to 0). The code for this selection occupies the upper byte of the configuration register in BCD. We combine this number with the required 06 in the lower byte to get xx06, where xx = 0 to 99. Input X0, X1, and X2 can only be filtered inputs. Each input has its own configuration register and filter time constant. Input X0 X1 X2 Configuration Register V7634 V7635 V7636 Function Filtered Input Filtered Input Filtered Input Hex Code Required xx06 (xx = filter delay time) 0 - 99 ms (BCD) xx06 (xx = filter delay time) 0 - 99 ms (BCD) xx06 (xx = filter delay time) 0 - 99 ms (BCD)
354
The following program selects Mode 60, then programs the filter delay time constants for inputs X0, X1, and X2. Each filter time constant is different, for illustration purposes. The program is otherwise generic, and may be adapted to your application.
DirectSOFT
SP0 LD K60 OUT V7633 LD K1006 OUT V7634 LD K2006 OUT V7635 LD K5006 OUT V7636
Load constant K60 into the accumulator. This selects Mode 60 as the HSIO mode. Output the constant to V7633, the location of the HSIO Mode select register. Load the constant K1006 which is required to configure filtered inputs with a time constant of 10 mS. Output this constant to V7634, configuring X0.
Load the constant K2006 which is required to select filtered inputs with a 20 mS filter time constant. Output this constant to V7635, configuring X1.
Load the constant K5006 which is required to select filtered inputs with a 50 mS filter time constant. Output this constant to V7636, configuring X2.
Main Program
END
Insert Main Program rungs here for your application. END coil marks the end of the main program..
14
42
Introduction
The Central Processing Unit (CPU) is the heart of the Micro PLC. Almost all PLC operations are controlled by the CPU, so it is important that it is set up correctly. This chapter provides the information needed to understand: S Steps required to set up the CPU S Operation of ladder programs S Organization of Variable Memory
To Programming Device or Operator Interface
DL05 PLC
CPU
Main Power Supply Input Circuit
Power Input
2 Comm. Ports
Output Circuit
NOTE: The High-Speed I/O function (HSIO) consists of dedicated but configurable hardware in the DL05. It is not considered part of the CPU, because it does not execute the ladder program. For more on HSIO operation, see Chapter 3. CPU Specifications and Operation
The DL05 Micro PLC which has 6K words of memory comprised of 2.0K of ladder memory and 4K words of V-memory (data registers). Program storage is in the FLASH memory which is a part of the CPU board in the PLC. In addition, there is RAM with the CPU which will store system parameters, V-memory, and other data which is not in the application program. The RAM is backed up by a super-capacitor, storing the data for several hours in the event of a power outage. The capacitor automatically charges during powered operation of the PLC. The DL05 supports fixed I/O which includes eight discrete input points and six output points. No provision for expansion beyond these fourteen I/O points is available in the DL05 model PLCs. Over 120 different instructions are available for program development as well as extensive internal diagnostics that can be monitored from the application program or from an operator interface. Chapters 5, 6, and 7 provide detailed descriptions of the instructions. The DL05 provides two built-in RS232C communication ports, so you can easily connect a handheld programmer, operator interface, or a personal computer without needing any additional hardware.
43
CPU Specifications
Feature Total Program memory (words) Ladder memory (words) Total V-memory (words) User V-memory (words) Non-volatile V Memory (words) Contact execution (boolean) Typical scan (boolean) RLL Ladder style Programming RLL and RLL PLUS Programming DL05 6K 2048 4096 3968 128 2.0uS 2.73.2mS Yes Yes Yes Variable / fixed Yes Yes Yes Standard on CPU 14 None Yes, 2 8 inputs, 6 outputs 129 512 512 256 SOFT programming for Windows
Direct
Built-in communication ports (RS232C) FLASH Memory Local Discrete I/O points available Local Analog input / output channels maximum High-Speed I/O (quad., pulse out, interrupt, pulse catch, etc.) I/O Point Density Number of instructions available (see Chapter 5 for details) Control relays Special relays (system defined) Stages in Timers Counters Immediate I/O Interrupt input (external / timed) Subroutines For/Next Loops Math Drum Sequencer Instruction Time of Day Clock/Calendar Internal diagnostics Password security System error log User error log Battery backup RLL PLUS
128 128 Yes Yes Yes Yes Integer Yes No Yes Yes No No No (uses super-cap.)
44
1 2 3 4 5 6
0V 5V RXD TXD 5V 0V
Power () connection (GND) Power (+) conection Receive Data (RS232C) Transmit Data (RS232C Power (+) conection Power () connection (GND)
Top View
45
If youre using a Personal Computer with the Direct SOFT programming package, you can connect the computer to either of the DL05s programming ports. For an engineering office environment (typical during program development), this is the preferred method of programming.
The Handheld programmer is connected to the CPU with a handheld programmer cable. This device is ideal for maintaining existing installations or making small program changes. The handheld programmer is shipped with a cable, which is approximately 6.5 feet (200 cm) long.
Even if you have years of experience using PLCs, there are a few things you need to do before you can start entering programs. This section includes some basic things, such as changing the CPU mode, but it also includes some things that you may never have to use. Heres a brief list of the items that are discussed. S Selecting and Changing the CPU Modes S Using Auxiliary Functions S Clearing the program (and other memory areas) S How to initialize system memory S Setting retentive memory ranges The following paragraphs provide the setup information necessary to get the CPU ready for programming. They include setup instructions for either type of programming device you are using. The D2HPP Handheld Programmer Manual provides the Handheld keystrokes required to perform all of these operations. The Direct SOFT Manual provides a description of the menus and keystrokes required to perform the setup procedures via Direct SOFT.
46
Mode Switch
Status Indicators
Status Indicators
The status indicator LEDs on the CPU front panels have specific functions which can help in programming and troubleshooting.
Indicator PWR Status ON OFF RUN ON OFF CPU ON OFF TX1 ON OFF RX1 ON OFF TX2 ON OFF RX2 ON OFF Meaning Power good Power failure CPU is in Run Mode CPU is in Stop or program Mode CPU self diagnostics error CPU self diagnostics good Data is being transmitted by the CPU - Port 1 No data is being transmitted by the CPU - Port 1 Data is being received by the CPU - Port 1 No data is being received by the CPU - Port 1 Data is being transmitted by the CPU - Port 2 No data is being transmitted by the CPU - Port 2 Data is being received by the CPU - Port 2 No data is being received by the CPU - Port 2
The mode switch on the DL05 PLC provides positions for enabling and disabling program changes in the CPU. Unless the mode switch is in the TERM position, RUN and STOP mode changes will not be allowed by any interface device, (handheld programmer, Direct SOFT programing package or operator interface). Programs may be viewed or monitored but no changes may be made. If the switch is in the TERM position and no program password is in effect, all operating modes as well as program access will be allowed through the connected programming or monitoring device.
47
CPU Action CPU is forced into the RUN mode if no errors are encountered. No changes are allowed by the attached programming/monitoring device. RUN, PROGRAM and the TEST modes are available. Mode and program changes are allowed by the programming/monitoring device. CPU is forced into the STOP mode. No changes are allowed by the programming/monitoring device.
Changing Modes in There are two ways to change the CPU mode. You can use the CPU mode switch to select the operating mode, or you can place the mode switch in the TERM position the DL05 PLC and use a programming device to change operating modes. With the switch in this position, the CPU can be changed between Run and Program modes. You can use either DirectSOFT or the Handheld Programmer to change the CPU mode of operation. With DirectSOFT you use a menu option in the PLC menu. With the Handheld Programmer, you use the MODE key.
Menu Options
MODE Key
Mode of Operation The DL05 CPU will normally power-up in the mode that it was in just prior to the power interruption. For example, if the CPU was in Program Mode when the power at Power-up was disconnected, the CPU will power-up in Program Mode (see warning note below). WARNING: Once the super capacitor has discharged, the system memory may not retain the previous mode of operation. When this occurs, the PLC can power-up in either Run or Program Mode if the mode switch is in the term position. There is no way to determine which mode will be entered as the startup mode. Failure to adhere to this warning greatly increases the risk of unexpected equipment startup.
48
Auxiliary Functions Many CPU setup tasks involve the use of Auxiliary (AUX) Functions. The AUX Functions perform many different operations, ranging from clearing ladder memory, displaying the scan time, copying programs to EEPROM in the handheld programmer, etc. They are divided into categories that affect different system parameters. Appendix A provides a description of the AUX functions. You can access the AUX Functions from Direct SOFT or from the D2HPP Handheld Programmer. The manuals for those products provide step-by-step procedures for accessing the AUX Functions. Some of these AUX Functions are designed specifically for the Handheld Programmer setup, so they will not be needed (or available) with the Direct SOFT package. The following table shows a list of the Auxiliary functions for the Handheld Programmer.
AUX 2* RLL Operations 21 22 23 24 Check Program Change Reference Clear Ladder Range Clear All Ladders 61 62 65 5B 5D HSIO Configuration Scan Control Setup AUX 6* Handheld Programmer Configuration Show Revision Numbers Beeper On / Off Run Self Diagnostics AUX 7* EEPROM Operations 71 72 73 74 75 76 Copy CPU memory to HPP EEPROM Write HPP EEPROM to CPU Compare CPU to HPP EEPROM Blank Check (HPP EEPROM) Erase HPP EEPROM Show EEPROM Type (CPU and HPP)
AUX 5* CPU Configuration 51 53 54 55 Modify Program Name Display Scan Time Initialize Scratchpad Set Watchdog Timer Set Communication Port 2 Set Retentive Ranges Test Operations Override Setup
56 57 58 59
Before you enter a new program, be sure to always clear ladder memory. You can use AUX Function 24 to clear the complete program. You can also use other AUX functions to clear other memory areas. S S S AUX 23 Clear Ladder Range AUX 24 Clear all Ladders AUX 31 Clear V Memory
The DL05 Micro PLC maintain system parameters in a memory area often referred to as the scratchpad. In some cases, you may make changes to the system setup that will be stored in system memory. For example, if you specify a range of Control Relays (CRs) as retentive, these changes are stored in system memory. AUX 54 resets the system memory to the default values.
49
WARNING: You may never have to use this feature unless you want to clear any setup information that is stored in system memory. Usually, youll only need to initialize the system memory if you are changing programs and the old program required a special system setup. You can usually load in new programs without ever initializing system memory. Remember, this AUX function will reset all system memory. If you have set special parameters such as retentive ranges, etc. they will be erased when AUX 54 is used. Make sure you that you have considered all ramifications of this operation before you select it. Setting Retentive Memory Ranges The DL05 PLCs provide certain ranges of retentive memory by default. The default ranges are suitable for many applications, but you can change them if your application requires additional retentive ranges or no retentive ranges at all. The default settings are:
Memory Area Control Relays V Memory Timers Counters Stages DL05 Default Range C400 C777 V1400 V7777 None by default CT0 CT177 None by default Available Range C0 C777 V0 V7777 T0 T177 CT0 CT177 S0 S377
You can use AUX 57 to set the retentive ranges. You can also use Direct SOFT menus to select the retentive ranges. Appendix A contains detailed information about auxiliary WARNING: The DL05 PLCs do not have battery back-up. The super capacitor will retain the values in the event of a power loss, but only for a short period of time, depending on conditions.
410
Using a Password
The DL05 PLCs allow you to use a password to help minimize the risk of unauthorized program and/or data changes. Once you enter a password you can lock the PLC against access. Once the CPU is locked you must enter the password before you can use a programming device to change any system parameters. You can select an 8-digit numeric password. The Micro PLCs are shipped from the factory with a password of 00000000. All zeros removes the password protection. If a password has been entered into the CPU you cannot just enter all zeros to remove it. Once you enter the correct password, you can change the password to all zeros to remove the password protection. WARNING: Make sure you remember your password. If you forget your password you will not be able to access the CPU. The Micro PLC must be returned to the factory to have the password removed. You can use the D2HPP Handheld Programmer or Direct SOFT to enter a password. The following diagram shows how you can enter a password with the Handheld Programmer.
DirectSOFT
Select AUX 81
CLR CLR I 8 B 1 AUX ENT
D2HPP
PASSWORD 00000000
PASSWORD XXXXXXXX
Press CLR to clear the display There are three ways to lock the CPU once the password has been entered. 1. If the CPU power is disconnected, the CPU will be automatically locked against access. 2. If you enter the password with Direct SOFT, the CPU will be automatically locked against access when you exit Direct SOFT. 3. Use AUX 83 to lock the CPU. When you use Direct SOFT, you will be prompted for a password if the CPU has been locked. If you use the Handheld Programmer, you have to use AUX 82 to unlock the CPU. Once you enter AUX 82, you will be prompted to enter the password.
411
CPU Operation
Achieving the proper control for your equipment or process requires a good understanding of how DL05 CPUs control all aspects of system operation. There are four main areas to understand before you create your application program: S CPU Operating System the CPU manages all aspects of system control. A quick overview of all the steps is provided in the next section. S CPU Operating Modes The two primary modes of operation are Program Mode and Run Mode. S CPU Timing The two important areas we discuss are the I/O response time and the CPU scan time. S CPU Memory Map DL05 CPUs offer a wide variety of resources, such as timers, counters, inputs, etc. The memory map section shows the organization and availability of these data types. CPU Operating System At powerup, the CPU initializes the internal electronic hardware. Memory initialization starts with examining the retentive memory settings. In general, the contents of retentive memory is preserved, and non-retentive memory is initialized to zero (unless otherwise specified). After the one-time powerup tasks, the CPU begins the cyclical scan activity. The flowchart to the right shows how the tasks differ, based on the CPU mode and the existence of any errors. The scan time is defined as the average time around the task loop. Note that the CPU is always reading the inputs, even during program mode. This allows programming tools to monitor input status at any time. The outputs are only updated in Run mode. In program mode, they are in the off state. Error detection has two levels. Non-fatal errors are reported, but the CPU remains in its current mode. If a fatal error occurs, the CPU is forced into program mode and the outputs go off.
Power up Initialize hardware Initialize various memory based on retentive configuration
Mode?
Do diagnostics
OK
YES
NO
412
Program Mode
In Program Mode, the CPU does not execute the application program or update the output points. The primary use for Program Mode is to enter or change an application program. You also use program mode to set up the CPU parameters, such as HSIO features, retentive memory areas, etc. You can use a programming device, such as DirectSOFT or the D2HPP Handheld Programmer to place the CPU in Program Mode.
Download Program
Run Mode
In Run Mode, the CPU executes the application program and updates the I/O system. You can perform many operations during Run Mode. Some of these include: S Monitor and change I/O point status S Update timer/counter preset values S Update Variable memory locations Run Mode operation can be divided into several key areas. For the vast majority of applications, some of these execution segments are more important than others. For example, you need to understand how the CPU updates the I/O points, handles forcing operations, and solves the application program. The remaining segments are not that important for most applications. You can use DirectSOFT or the D2HPP Handheld Programmer to place the CPU in Run Mode.
You can also edit the program during Run Mode. The Run Mode Edits are not bumpless to the outputs. Instead, the CPU maintains the outputs in their last state while it accepts the new program information. If an error is found in the new program, then the CPU will turn all the outputs off and enter the Program Mode. This feature is discussed in more detail in Chapter 8. WARNING: Only authorized personnel fully familiar with all aspects of the application should make changes to the program. Changes during Run Mode become effective immediately. Make sure you thoroughly consider the impact of any changes to minimize the risk of personal injury or damage to equipment.
413
Read Inputs
The CPU reads the status of all inputs, then stores it in the image register. Input image register locations are designated with an X followed by a memory location. Image register data is used by the CPU when it solves the application program. Of course, an input may change after the CPU has just read the inputs. Generally, the CPU scan time is measured in milliseconds. If you have an application that cannot wait until the next I/O update, you can use Immediate Instructions. These do not use the status of the input image register to solve the application program. The Immediate instructions immediately read the input status directly from the I/O modules. However, this lengthens the program scan since the CPU has to read the I/O point status again. A complete list of the Immediate instructions is included in Chapter 5.
Service Peripherals After the CPU reads the inputs from the input modules, it reads any attached peripheral devices. This is primarily a communications service for any attached and Force I/O devices. For example, it would read a programming device to see if any input, output, or other memory type status needs to be modified. There are two basic types of forcing available with the DL05 CPUs. S Forcing from a peripheral not a permanent force, good only for one scan S Bit Override holds the I/O point (or other bit) in the current state. Valid bits are X, Y, C, T, CT, and S. (These memory types are discussed in more detail later in this chapter). Regular Forcing This type of forcing can temporarily change the status of a discrete bit. For example, you may want to force an input on, even though it is really off. This allows you to change the point status that was stored in the image register. This value will be valid until the image register location is written to during the next scan. This is primarily useful during testing situations when you need to force a bit on to trigger another event. Bit Override Bit override can be enabled on a point-by-point basis by using AUX 59 from the Handheld Programmer or, by a menu option from within Direct SOFT. Bit override basically disables any changes to the discrete point by the CPU. For example, if you enable bit override for X1, and X1 is off at the time, then the CPU will not change the state of X1. This means that even if X1 comes on, the CPU will not acknowledge the change. So, if you used X1 in the program, it would always be evaluated as off in this case. Of course, if X1 was on when the bit override was enabled, then X1 would always be evaluated as on. There is an advantage available when you use the bit override feature. The regular forcing is not disabled because the bit override is enabled. For example, if you enabled the Bit Override for Y0 and it was off at the time, then the CPU would not change the state of Y0. However, you can still use a programming device to change the status. Now, if you use the programming device to force Y0 on, it will remain on and the CPU will not change the state of Y0. If you then force Y0 off, the CPU will maintain Y0 as off. The CPU will never update the point with the results from the application program or from the I/O update until the bit override is removed. The following diagram shows a brief overview of the bit override feature. Notice the CPU does not update the Image Register when bit override is enabled. CPU Specifications and Operation
414
Input Update
Input Update
X128 OFF Y128 OFF C377 OFF ... ... ... ... ... ... X2 ON Y2 ON C2 ON X1 ON Y1 ON C1 OFF X0 OFF Y0 OFF C0 OFF
Bit Override ON
WARNING: Only authorized personnel fully familiar with all aspects of the application should make changes to the program. Make sure you thoroughly consider the impact of any changes to minimize the risk of personal injury or damage to equipment.
Update Special There are certain V-memory locations that contain Special Relays and other Relays and Special dedicated register information. This portion of the execution cycle makes sure these locations get updated on every scan. Also, there are several different Special Registers Relays, such as diagnostic relays, etc., that are also updated during this segment. Solve Application Program The CPU evaluates each instruction in the application program during this segment of the scan cycle. The instructions define the relationship between the input conditions and the desired output response. The CPU uses the output image register area to store the status of the desired action for the outputs. Output image register locations are designated with a Y followed by a memory location. The actual outputs are updated during the write outputs segment of the scan cycle. There are immediate output instructions available that will update the output points immediately instead of waiting until the write output segment. A complete list of the Immediate instructions is provided in Chapter 5. The internal control relays (C), the stages (S), and the variable memory (V) are also updated in this segment.
You may recall that you can force various types of points in the system. (This was discussed earlier in this chapter.) If any I/O points or memory data have been forced, the output image register also contains this information.
415
Write Outputs
Once the application program has solved the instruction logic and constructed the output image register, the CPU writes the contents of the output image register to the corresponding output points. Remember, the CPU also made sure that any forcing operation changes were stored in the output image register, so the forced points get updated with the status specified earlier. During this part of the scan, the CPU performs all system diagnostics and other tasks such as calculating the scan time and resetting the watchdog timer. There are many different error conditions that are automatically detected and reported by the DL05 PLCs. Appendix B contains a listing of the various error codes. Probably one of the more important things that occurs during this segment is the scan time calculation and watchdog timer control. The DL05 CPU has a watchdog timer that stores the maximum time allowed for the CPU to complete the solve application segment of the scan cycle. If this time is exceeded the CPU will enter the Program Mode and turn off all outputs. The default value set from the factory is 200 ms. An error is automatically reported. For example, the Handheld Programmer would display the following message E003 S/W TIMEOUT when the scan overrun occurs. You can use AUX 53 to view the minimum, maximum, and current scan time. Use AUX 55 to increase or decrease the watchdog timer value.
Diagnostics
416
Scan
Solve Program
Write Outputs
Solve Program
Solve Program
Field Input
CPU Reads Inputs CPU Writes Outputs
In this case, you can calculate the response time by simply adding the following items: Input Delay + Scan Time + Output Delay = Response Time Normal Maximum I/O Response The I/O response time is longest when the input changes just after the Read Inputs portion of the execution cycle. In this case the new input status is not read until the following scan. The following diagram shows an example of the timing for this situation.
Scan Solve Program
Read Inputs
Scan
Solve Program
Write Outputs
Solve Program
Solve Program
Field Input
CPU Reads Inputs CPU Writes Outputs
In this case, you can calculate the response time by simply adding the following items: Input Delay +(2 x Scan Time) + Output Delay = Response Time
417
There are a few things you can do the help improve throughput. S You can choose instructions with faster execution times S You can use immediate I/O instructions (which update the I/O points during the program execution) S You can use the HSIO Mode 50 Pulse Catch features designed to operate in high-speed environments. See the Chapter 3 for details on using this feature. Of these three things the Immediate I/O instructions are probably the most important and most useful. The following example shows how an immediate input instruction and immediate output instruction would affect the response time.
Scan
Scan
Solve Program
Normal Read Input Read Input Immediate
Solve Program
Write Output Immediate
Solve Program
Normal Write Outputs
Solve Program
Field Input
In this case, you can calculate the response time by simply adding the following items. CPU Specifications and Operation Input Delay + Instruction Execution Time + Output Delay = Response Time The instruction execution time would be calculated by adding the time for the immediate input instruction, the immediate output instruction, and any other instructions in between the two. NOTE: Even though the immediate instruction reads the most current status from I/O, it only uses the results to solve that one instruction. It does not use the new status to update the image register. Therefore, any regular instructions that follow will still use the image register values. Any immediate instructions that follow will access the I/O again to update the status.
418
Do diagnostics
OK
YES
NO
The time required during each scan to read the input status is 40 mS. Dont confuse this with the I/O response time that was discussed earlier. The time required to write the output status is 629 mS. Dont confuse this with the I/O response time that was discussed earlier.
Writing Outputs
419
Application The CPU processes the program from address 0 to the END instruction. The CPU Program Execution executes the program left to right and top to bottom. As each rung is evaluated the appropriate image register or memory location is updated. The time required to solve the application program depends on the type and number of instructions used, and the amount of execution overhead. Just add the execution times for all the instructions in your program to determine to total execution time. Appendix C provides a complete list of the instruction execution times for the DL05 Micro PLC. For example, the execution time for running the program shown below is calculated as follows: Instruction STR X0 OR C0 ANDN X1 OUT Y0 STRN C100 LD K10 STRN C101 OUT V2002 STRN C102 LD K50 STRN C103 OUT V2006 STR X5 ANDN X10 OUT Y3 END SUBTOTAL Overhead Minimum Maximum DL05 0.66 mS 2.5 ms Time 2 ms 1.6 ms 1.6 ms 6.8 ms 2.3 ms 42.7 ms 2.3 ms 16.6 ms 2.3 ms 42.7 ms 2.3 ms 16.6 ms 2 ms 1.6 ms 6.8 ms 24 ms 174.2 ms
X0 X1 Y0 OUT
C0
C100
LD K10
C101
OUT
V2002
C102
LD K50
C103
OUT
V2006
X5
X10
Y3 OUT
END
TOTAL TIME = (Program execution time + Overhead) x 1.1 The program above takes only 174.2 ms to execute during each scan. The DL05 spends 0.1ms, on internal timed interrupt management, for every 1ms of instruction time. The total scan time is calculated by adding the program execution time to the overhead (shown above)and multiplying the result (ms) by 1.1. Overhead includes all other housekeeping and diagnostic tasks. The scan time will vary slightly from one scan to the next, because of fluctuation in overhead tasks. Program Control Instructions the DL05 PLCs have an interrupt routine feature that changes the way a program executes. Since this instruction interrupts normal program flow, it will have an effect on the program execution time. For example, a timed interrupt routine with a 10 mS period interrupts the main program execution (before the END statement) every 10 mS, so the CPU can execute the interrupt routine. Chapter 5 provides detailed information on interrupts.
420
binary
0402 ? 7 961428 ASCII hexadecimal 1001011011 177 1011 ? decimal A 72B ? 300124 3A9
PLC Resources
As any good computer does, PLCs store and manipulate numbers in binary form: just ones and zeros. So why do we have to deal with numbers in so many different forms? Numbers have meaning, and some representations are more convenient than others for particular purposes. Sometimes we use numbers to represent a size or amount of something. Other numbers refer to locations or addresses, or to time. In science we attach engineering units to numbers to give a particular meaning. PLCs offer a fixed amount of resources, depending on the model and configuration. We use the word resources to include variable memory (V-memory), I/O points, timers, counters, etc. Most modular PLCs allow you to add I/O points in groups of eight. In fact, all the resources of our PLCs are counted in octal. Its easier for computers to count in groups of eight than ten, because eight is an even power of 2. Octal means simply counting in groups of eight things at a time. In the figure to the right, there are eight circles. The quantity in decimal is 8, but in octal it is 10 (8 and 9 are not valid in octal). In octal, 10 means 1 group of 8 plus 0 (no individuals). Decimal 1 2 3 4 5 6 7 8
Octal
1 2 3 4 5 6 7 10
In the figure below, we have two groups of eight circles. Counting in octal we have 20 items, meaning 2 groups of eight, plus 0 individuals Dont say twenty, say twozero octal. This makes a clear distinction between number systems. Decimal 1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16
Octal
2 3 4
7 10
11 12 13 14 15 16 17 20
After counting PLC resources, its time to access PLC resources (theres a difference). The CPU instruction set accesses resources of the PLC using octal addresses. Octal addresses are the same as octal quantities, except they start counting at zero. The number zero is significant to a computer, so we dont skip it. Our circles are in an array of square containers to the right. To access a resource, our PLC instruction will address its location using the octal references shown. If these were counters, CT14 would access the black circle location.
X= 0 X 1X 2X 1 2 3 4 5 6 7
421
VMemory
Variable memory (called V-memory) stores data for the ladder program and for configuration settings. V-memory locations and V-memory addresses are the same thing, and are numbered in octal. For example, V2073 is a valid location, while V1983 is not valid (9 and 8 are not valid octal digits). Each V-memory location is one data word wide, meaning 16 bits. For configuration registers, our manuals will show each bit of a V-memory word. The least significant bit (LSB) will be on the right, and the most significant bit (MSB) on the left. We use the word significant, referring to the relative binary weighting of the bits. V-memory address (octal)
V2017
MSB
LSB
0 1 0 0 1 1 1 0 0 0 1 0 1 0 0 1
V-memory data is 16-bit binary, but we rarely program the data registers one bit at a time. We use instructions or viewing tools that let us work with decimal, octal, and hexadecimal numbers. All these are converted and stored as binary for us. A frequently-asked question is How do I tell if a number is octal, BCD, or hex? The answer is that we usually cannot tell just by looking at the data... but it does not really matter. What matters is: the source or mechanism which writes data into a V-memory location and the thing which later reads it must both use the same data type (i.e., octal, hex, binary, or whatever). The V-memory location is just a storage box... thats all. It does not convert or move the data on its own. Since humans naturally count in decimal (10 fingers, 10 toes), we prefer to enter and view PLC data in decimal as well. However, computers are more efficient in using pure binary numbers. A compromise solution between the two is Binary-Coded Decimal (BCD) representation. A BCD digit ranges from 0 to 9, and is stored as four binary bits (a nibble). This permits each V-memory location to store four BCD digits, with a range of decimal numbers from 0000 to 9999.
BCD number V-memory storage
4
0 1 0 0
9
1 0 0 1
3
0 0 1 1
6
0 1 1 0 CPU Specifications and Operation
In a pure binary sense, a 16-bit word can represent numbers from 0 to 65535. In storing BCD numbers, the range is reduced to only 0 to 9999. Many math instructions use Binary-Coded Decimal (BCD) data, and DirectSOFT and the handheld programmer allow us to enter and view data in BCD. Hexadecimal Numbers Hexadecimal numbers are similar to BCD numbers, except they utilize all possible binary values in each 4-bit digit. They are base-16 numbers so we need 16 different digits. To extend our decimal digits 0 through 9, we use A through F as shown.
Decimal Hexadecimal 0 1 2 3 0 1 2 3 4 5 4 5 6 6 7 7 8 9 10 11 12 13 14 15 8 9 A B C D E F
A 4-digit hexadecimal number can represent all 65536 values in a V-memory word. The range is from 0000 to FFFF (hex). PLCs often need this full range for sensor data, etc. Hexadecimal is just a convenient way for humans to view full binary data.
Hexadecimal number V-memory storage
A
1 0 1 0
7
0 1 1 1
F
1 1 1 1
4
0 1 0 0
422
Memory Map
With any PLC system, you generally have many different types of information to process. This includes input device status, output device status, various timing elements, parts counts, etc. It is important to understand how the system represents and stores the various types of data. For example, you need to know how the system identifies input points, output points, data words, etc. The following paragraphs discuss the various memory types used in DL05 Micro PLCs. A memory map overview for the CPU follows the memory descriptions. Octal Numbering System All memory locations and resources are numbered in Octal (base 8). For example, the diagram shows how the octal numbering system works for the discrete input points. Notice the octal system does not contain any numbers with the digits 8 or 9.
X0 X1 X2 X3 X4 X5 X6 X7
X10 X11
As you examine the different memory types, youll notice two types of memory in the DL05, discrete and word memory. Discrete memory is one bit that can be either a 1 or a 0. Word memory is referred to as V memory (variable) and is a 16-bit location normally used to manipulate data/numbers, store data/numbers, etc. Some information is automatically stored in V memory. For example, the timer current values are stored in V memory.
The discrete memory area is for inputs, outputs, control relays, special relays, stages, timer status bits and counter status bits. However, you can also access the bit data types as a V-memory word. Each V-memory location contains 16 consecutive discrete locations. For example, the following diagram shows how the X input points are mapped into V-memory locations.
8 Discrete (X) Input Points
X7 X6 X5 X4 X3 X2 X1 X0
Bit # 15
14
13
12
11
10
V40400
These discrete memory areas and their corresponding V memory ranges are listed in the memory area table for DL05 Micro PLCs on the following pages.
423
Y0 OUT
The discrete input points are noted by an X data type. There are 8 discrete input points and 256 discrete input addresses available with DL05 CPUs. In this example, the output point Y0 will be turned on when input X0 energizes. The discrete output points are noted by a Y data type. There are 6 discrete outputs and 256 discrete output addresses available with DL05 CPUs. In this example, output point Y1 will be turned on when input X1 energizes. Control relays are discrete bits normally used to control the user program. The control relays do not represent a real world device, that is, they cannot be physically tied to switches, output coils, etc. They are internal to the CPU. Because of this, control relays can be programmed as discrete inputs or discrete outputs. These locations are used in programming the discrete memory locations (C) or the corresponding word location which contains 16 consecutive discrete locations. In this example, memory location C5 will energize when input X6 turns on. The second rung shows a simple example of how to use a control relay as an input. Timer status bits reflect the relationship between the current value and the preset value of a specified timer. The timer status bit will be on when the current value is equal or greater than the preset value of a corresponding timer. When input X0 turns on, timer T1 will start. When the timer reaches the preset of 3 seconds (K of 30) timer status contact T1 turns on. When T1 turns on, output Y12 turns on. Turning off X0 resets the timer.
X0
X1
Y1 OUT
X6
C5 OUT
C5
X0
TMR K30
T1
T1
Y12 OUT
424
As mentioned earlier, some information is automatically stored in V memory. This is true for the current values associated with timers. For example, V0 holds the current value for Timer 0, V1 holds the current value for Timer 1, etc. The primary reason for this is programming flexibility. The example shows how you can use relational contacts to monitor several time intervals from a single timer.
X0
V1
V1
K50
V1
K75
Y4 OUT
Counter status bits that reflect the relationship between the current value and the preset value of a specified counter. The counter status bit will be on when the current value is equal to or greater than the preset value of a corresponding counter.
X0 X1
CNT K10
CT3
CT3
Y2 OUT
Each time contact X0 transitions from off to on, the counter increments by one. (If X1 comes on, the counter is reset to zero.) When the counter reaches the preset of 10 counts (K of 10) counter status contact CT3 turns on. When CT3 turns on, output Y2 turns on. Counter Current Values (V Data Type) CPU Specifications and Operation Just like the timers, the counter current values are also automatically stored in V memory. For example, V1000 holds the current value for Counter CT0, V1001 holds the current value for Counter CT1, etc. The primary reason for this is programming flexibility. The example shows how you can use relational contacts to monitor the counter values.
X0 X1
CNT K10
CT3
V1003
K1
V1003
K3
V1003
K5
Y4 OUT
425
Word memory is referred to as V memory (variable) and is a 16-bit location normally used to manipulate data/numbers, store data/numbers, etc. Some information is automatically stored in V memory. For example, the timer current values are stored in V memory. The example shows how a four-digit BCD constant is loaded into the accumulator and then stored in a V-memory location.
X0
LD K1345
OUT
V2000
Stages are used in RLL PLUS programs to create a structured program, similar to a flowchart. Each program Staget denotes a program segment. When the program segment, or Staget, is active, the logic within that segment is executed. If the Staget is off, or inactive, the logic is not executed and the CPU skips to the next active Staget. (See Chapter 7 for a more detailed description of RLL PLUS programming.) Each Staget also has a discrete status bit that can be used as an input to indicate whether the Staget is active or inactive. If the Staget is active, then the status bit is on. If the Staget is inactive, then the status bit is off. This status bit can also be turned on or off by other instructions, such as the SET or RESET instructions. This allows you to easily control stages throughout the program. Special relays are discrete memory locations with pre-defined functionality. There are many different types of special relays. For example, some aid in program development, others provide system operating status information, etc. Appendix D provides a complete listing of the special relays. In this example, control relay C10 will energize for 50 ms and de-energize for 50 ms because SP5 is a predefined relay that will be on for 50 ms and off for 50 ms.
Ladder Representation
ISG S0000 Start X0 S500 JMP SG S0001
Wait forStart
S1 JMP
SG S0002
Part Locked X2
SP5
C10 OUT
426
V7620 Sets the V-memory location that contains the value. V7621 Sets the V-memory location that contains the message. V7622 Sets the total number (1 16) of V-memory locations to be displayed. V7623 Sets the V-memory location that contains the numbers to be displayed. V7624 Sets the V-memory location that contains the character code to be displayed. V7625 Contains the function number that can be assigned to each key. V7626 Powerup operational mode. V7627 Change preset value. V7630 Starting location for the multistep presets for channel 1. The default value is 2320, which indicates the first value should be obtained from V2320. Since there are 24 presets available, the default range is V2320 V2377. You can change the starting point if necessary. Reserved Sets the desired function code for the high speed counter, interrupt, pulse catch, pulse train, and input filter. Location is also used for setting the power-up in Run Mode option.
V7631V7632 V7633
N/A Default: 0060 Lower Byte Range: Range: 10 Counter 20 Quadrature 30 Pulse Out 40 Interrupt 50 Pulse Catch 60 Filtered discrete In. Upper Byte Range: Bits 8 12, 14,15: Unused Bit 13: Power-up in Run (only applies if mode switch is in term position)
X0 Setup Register for High-Speed I/O functions X1 Setup Register for High-Speed I/O functions X2 Setup Register for High-Speed I/O functions Reserved Timed Interrupt
Default: 1006 Default: 1006 Default: 1006 N/A Default: 0000 Range: 000303E7h (39999ms) N/A Default: 00E0 Default: 8501
Reserved Port 2: Setup for the protocol, time-out, and the response delay time. Port 2: Setup for the station number, baud rate, STOP bit, and parity.
427
System V-memory V7657 V7660 V7661 V7662V7717 V7720V7722 V7720 V7721 V7722 V7723V7750 V7751 V7752V7754 V7755 V7756 V7757 V7760V7762 V7763 V7764 V7765 V7766V7774 V7775 V7776 V7777
Description of Contents Port 2: Setup completion code used to notify the completion of the parameter setup. Scan contro setup: Keeps the scan control mode. Setup timer over counter: Counts the times the actual scan time exceeds the user setup time. Reserved Locations for DV1000 operator interface parameters. Titled Timer preset value pointer Title Counter preset value pointer HiByte-Titled Timer preset block size, LoByte-Titled Counter preset block size Reserved Fault Message Error Code stores the 4-digit code used with the FAULT instruction when the instruction is executed. Reserved Error code stores the fatal error code. Error code stores the major error code. Error code stores the minor error code. Reserved Program address where syntax error exists Syntax error code Scan stores the total number of scan cycles that have occurred since the last Program Mode to Run Mode transition. Reserved Scan stores the current scan time (milliseconds). Scan stores the minimum scan time that has occurred since the last Program Mode to Run Mode transition (milliseconds). Scan stores the maximum scan time that has occurred since the last Program Mode to Run Mode transition (milliseconds).
Default Values / Ranges Default: 0A00 Default: 0000 N/A N/A N/A N/A N/A N/A N/A N/A N/A
N/A
428
Input Points (See note 1) Output Points (See note 1) Control Relays
X0
Y0 Y377
V40500 V40517
256
Y0
C0 C777
V40600 - V40637
512
C0
C0
Special Relays
SP0 SP777
V41200 V41237
512
SP0
Timers
T0 T177
V41100 V41107
128
TMR K100
T0
None
V0 V177
128
V0
K100
V41100 V41107
128
T0
Counters
CT0 CT177
V41140 V41147
128
Counter Current Values Counter Status Bits Data Words Data Words Nonvolatile Stages
None
V1000 V1177
128
V1000
K100
CT0 CT177
V41140 V41147
128
CT0
None specific, used with many instructions None specific, used with many instructions
SG S 001
S0
System parameters
None
V7600 V7777
128
1 The DL05 systems are limited to 8 discrete inputs and 6 discrete outputs with the present available hardware, but 256 point addresses exist.
429
LSB 5
005
15
14
13
12
11
10
7
007
6
006
4
004
3
003
2
002
1
001
0
000
Address
V40400
LSB 5
005
15
14
13
12
11
10
4
004
3
003
2
002
1
001
0
000
Address
V40500
LSB 5
005 025 045 065 105 125 145 165 205 225 245 265 305 325 345 365
15
015 035 055 075 115 135 155 175 215 235 255 275 315 335 355 375
14
014 034 054 074 114 134 154 174 214 234 254 274 314 334 354 374
13
013 033 053 073 113 133 153 173 213 233 253 273 313 333 353 373
12
012 032 052 072 112 132 152 172 212 232 252 272 312 332 352 372
11
011 031 051 071 111 131 151 171 211 231 251 271 311 331 351 371
10
010 030 050 070 110 130 150 170 210 230 250 270 310 330 350 370
7
007 027 047 067 107 127 147 167 207 227 247 267 307 327 347 367
6
006 026 046 066 106 126 146 166 206 226 246 266 306 326 346 366
4
004 024 044 064 104 124 144 164 204 224 244 264 304 324 344 364
3
003 023 043 063 103 123 143 163 203 223 243 263 303 323 343 363
2
002 022 042 062 102 122 142 162 202 222 242 262 302 322 342 362
1
001 021 041 061 101 121 141 161 201 221 241 261 301 321 341 361
0
000 020 040 060 100 120 140 160 200 220 240 260 300 320 340 360
Address
V41000 V41001 V41002 V41003 V41004 V41005 V41006 V41007 V41010 V41011 V41012 V41013 V41014 V41015 V41016 V41017
430
LSB 5
005 025 045 065 105 125 145 165 205 225 245 265 305 325 345 365 405 425 445 465 505 525 545 565 605 625 645 665 705 725 745 765
15
015 035 055 075 115 135 155 175 215 235 255 275 315 335 355 375 415 435 455 475 515 535 555 575 615 635 655 675 715 735 755 775
14
014 034 054 074 114 134 154 174 214 234 254 274 314 334 354 374 414 434 454 474 514 534 554 574 614 634 654 674 714 734 754 774
13
013 033 053 073 113 133 153 173 213 233 253 273 313 333 353 373 413 433 453 473 513 533 553 573 613 633 653 673 713 733 753 773
12
012 032 052 072 112 132 152 172 212 232 252 272 312 332 352 372 412 432 452 472 512 532 552 572 612 632 652 672 712 732 752 772
11
011 031 051 071 111 131 151 171 211 231 251 271 311 331 351 371 411 431 451 471 511 531 551 571 611 631 651 671 711 731 751 771
10
010 030 050 070 110 130 150 170 210 230 250 270 310 330 350 370 410 430 450 470 510 530 550 570 610 630 650 670 710 730 750 770
7
007 027 047 067 107 127 147 167 207 227 247 267 307 327 347 367 407 427 447 467 507 527 547 567 607 627 647 667 707 727 747 767
6
006 026 046 066 106 126 146 166 206 226 246 266 306 326 346 366 406 426 446 466 506 526 546 566 606 626 646 666 706 726 746 766
4
004 024 044 064 104 124 144 164 204 224 244 264 304 324 344 364 404 424 444 464 504 524 544 564 604 624 644 664 704 724 744 764
3
003 023 043 063 103 123 143 163 203 223 243 263 303 323 343 363 403 423 443 463 503 523 543 563 603 623 643 663 703 723 743 763
2
002 022 042 062 102 122 142 162 202 222 242 262 302 322 342 362 402 422 442 462 502 522 542 562 602 622 642 662 702 722 742 762
1
001 021 041 061 101 121 141 161 201 221 241 261 301 321 341 361 401 421 441 461 501 521 541 561 601 621 641 661 701 721 741 761
0
000 020 040 060 100 120 140 160 200 220 240 260 300 320 340 360 400 420 440 460 500 520 540 560 600 620 640 660 700 720 740 760
Address
V40600 V40601 V40602 V40603 V40604 V40605 V40606 V40607 V40610 V40611 V40612 V40613 V40614 V40615 V40616 V40617 V40620 V40621 V40622 V40623 V40624 V40625 V40626 V40627 V40630 V40631 V40632 V40633 V40634 V40635 V40636 V40637
431
LSB 5
005 025 045 065 105 125 145 165
15
015 035 055 075 115 135 155 175
14
014 034 054 074 114 134 154 174
13
013 033 053 073 113 133 153 173
12
012 032 052 072 112 132 152 172
11
011 031 051 071 111 131 151 171
10
010 030 050 070 110 130 150 170
7
007 027 047 067 107 127 147 167
6
006 026 046 066 106 126 146 166
4
004 024 044 064 104 124 144 164
3
003 023 043 063 103 123 143 163
2
002 022 042 062 102 122 142 162
1
001 021 041 061 101 121 141 161
0
000 020 040 060 100 120 140 160
Address
V41100 V41101 V41102 V41103 V41104 V41105 V41106 V41107
LSB 5
005 025 045 065 105 125 145 165
15
015 035 055 075 115 135 155 175
14
014 034 054 074 114 134 154 174
13
013 033 053 073 113 133 153 173
12
012 032 052 072 112 132 152 172
11
011 031 051 071 111 131 151 171
10
010 030 050 070 110 130 150 170
7
007 027 047 067 107 127 147 167
6
006 026 046 066 106 126 146 166
4
004 024 044 064 104 124 144 164
3
003 023 043 063 103 123 143 163
2
002 022 042 062 102 122 142 162
1
001 021 041 061 101 121 141 161
0
000 020 040 060 100 120 140 160
Address
V41140 V41141 V41142 V41143 V41144 V41145
V41146 V41147
432
Communication Port 1 Com 1 Connects to HPP, DirectSOFT, operator interfaces, etc. 6-pin, RS232C 9600 Baud (Fixed) Parity - odd (default), even, none Station address 1 (fixed) 8 data bits 1 start, 1 stop bit Asynchronous, Half-duplex, DTE Protocol: (Auto-Select) K sequence (Slave only)
DirectNET (Slave only) MODBUS (Slave only)
You will need to make sure the network connection is a 3-wire RS232 type. Normally, the RS232 signals are used for for communications between two devices with distances up to a maximum of 15 meters. CPU Specifications and Operation Networking DL05 to DL05 RS232C
1234 5 6
DL05 PORT 1 or 2
433
1234 5 6
F2UNICON
0V RXD TXD RTS 0V 1 RXD 3 TXD 4 RTS 5
GND TXD+ TXD RXD RXD+ GND RXD+ RXD TXD TXD+
DL05
1 0V 3 RXD 4 TXD 5 RTS 0V 1 PORT 2 RXD 3 TXD 4 RTS 5
FAISONET
Note: When using the DL05 on a multi-drop network, the RTS ON Delay time must be set to at least 5ms and the RTS OFF Delay time must be set to at least 2ms. If you encounter problems, the time can be increased.
F2UNICON
GND RXD+ RXD TXD
DL05
1 0V 3 RXD 4 TXD 5 RTS 0V 1 PORT 2 RXD 3 TXD 4 RTS 5
TXD+
DL05 PORT 2
1 0V 3 RXD 4 TXD 5 RTS 0V 1 RXD 3 TXD 4 RTS 5
F2UNICON
GND TXD+ TXD RXD RXD+ GND RXD+ RXD TXD TXD+
DL05
1 0V 3 RXD 4 TXD 5 RTS 0V 1 PORT 2 RXD 3 TXD 4 RTS 5
FAISONET
F2UNICON
GND RXD+ RXD TXD TXD+
DL240
1 0V 3 RXD 4 TXD 5 RTS 0V 1 PORT 2 RXD 3 TXD 4 RTS 5
434
In DirectSOFT, choose the PLC menu, then Setup, then Secondary Comm Port. S Port: From the port number list box at the top, choose Port 2. S Protocol: Click the check box to the left of MODBUS (use AUX 56 on the HPP, andselect MBUS), and then youll see the dialog box below.
Setup Communication Ports Port: Port 2 Protocol: K-sequence DirectNET MODBUS Non-sequence Timeout: 800 mS RTS ON Delay Time: 5 mS RTS OFF Delay Time: 2 mS Station Number: Baud Rate: Stop Bits: 1 38400 1 Close
Help
Parity: None
S S
S S
Timeout: amount of time the port will wait after it sends a message to get a response before logging an error. RTS ON / OFF Delay Time: The RTS ON Delay Time specifies the time the DL05 waits to send the data after it has raised the RTS signal line. The RTS OFF Delay Time specifies the time the DL05 waits to release the RTS signal line after the data has been sent. When using the DL05 on a multi-drop network, the RTS ON Delay time must be set to at least 5ms and the RTS OFF Delay time must be set to at least 2ms. If you encounter problems, the time can be increased. Station Number: For making the CPU port a MODBUSR master, choose 1. The possible range for MODBUS slave numbers is from 1 to 247, but the DL05 network instructions used in Master mode will access only slaves 1 to 99. Each slave must have a unique number. At powerup, the port is automatically a slave, unless and until the DL05 executes ladder logic network instructions which use the port as a master. Thereafter, the port reverts back to slave mode until ladder logic uses the port again. Baud Rate: The available baud rates include 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400 baud. Choose a higher baud rate initially, reverting to lower baud rates if you experience data errors or noise problems on the network. Important: You must configure the baud rates of all devices on the network to the same value. Refer to the appropriate product manual for details. Stop Bits: Choose 1 or 2 stop bits for use in the protocol. Parity: Choose none, even, or odd parity for error checking. Then click the button indicated to send the Port configuration to the CPU, and click Close.
435
In DirectSOFT, choose the PLC menu, then Setup, then Secondary Comm Port. S Port: From the port number list box, choose Port 2 . S Protocol: Click the check box to the left of DirectNET (use AUX 56 on the HPP, then select DNET), and then youll see the dialog box below.
Setup Communication Ports Port: Port 2 Protocol: K-sequence DirectNET MODBUS Non-sequence Timeout: 800 mS RTS ON Delay Time: 5 mS RTS OFF Delay Time: 2 mS Station Number: Baud Rate: Stop Bits: 1 38400 1 Close
Help
S S
S S S
Timeout: amount of time the port will wait after it sends a message to get a response before logging an error. RTS ON / OFF Delay Time: The RTS ON Delay Time specifies the time the DL05 waits to send the data after it has raised the RTS signal line. The RTS OFF Delay Time specifies the time the DL05 waits to release the RTS signal line after the data has been sent. When using the DL05 on a multi-drop network, the RTS ON Delay time must be set to at least 5ms and the RTS OFF Delay time must be set to at least 2ms. If you encounter problems, the time can be increased. Station Number: For making the CPU port a DirectNET master, choose 1. The allowable range for DIrectNET slaves is from 1 to 90 (each slave must have a unique number). At powerup, the port is automatically a slave, unless and until the DL05 executes ladder logic instructions which attempt to use the port as a master. Thereafter, the port reverts back to slave mode until ladder logic uses the port again. Baud Rate: The available baud rates include 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400 baud. Choose a higher baud rate initially, reverting to lower baud rates if you experience data errors or noise problems on the network. Important: You must configure the baud rates of all devices on the network to the same value. Stop Bits: Choose 1 or 2 stop bits for use in the protocol. Parity: Choose none, even, or odd parity for error checking. Format: Choose between hex or ASCII formats. Then click the button indicated to send the Port configuration to the CPU, and click Close.
436
There are typically two ways that most host software conventions allow you to specify a PLC memory location. These are: S By specifying the MODBUS data type and address S By specifying a MODBUS address only.
437
If Your Host Software Many host software packages allow you to specify the MODBUS data type and the Requires the Data MODBUS address that corresponds to the PLC memory location. This is the easiest Type and Address... method, but not all packages allow you to do it this way.
The actual equation used to calculate the address depends on the type of PLC data you are using. The PLC memory types are split into two categories for this purpose. Discrete X, SP, Y, CR, S, T, C (contacts) S Word V, Timer current value, Counter current value In either case, you basically convert the PLC octal address to decimal and add the appropriate MODBUS address (if required). The table below shows the exact equation used for each group of data.
DL05 Memory Type QTY (Dec.) PLC Range (Octal) + MODBUS Address Range (Decimal) Start of Range 2048 3072 2048 3072 6144 6400 5120 + 0 512 640 3968 127 639 3839 4095 2303 3583 2303 4583 6271 6527 5375 MODBUS Data Type + Data Type Input Input Coil Coil Coil Coil Coil Data Type Input Register Input Register S
For Discrete Data Types .... Convert PLC Addr. to Dec. Inputs (X) Special Relays (SP) Outputs (Y) Control Relays (CR) Timer Contacts (T) Counter Contacts (CT) Stage Status Bits (S) For Word Data Types .... Timer Current Values (V) Counter Current Values (V) V Memory, user data (V) 256 512 256 512 128 128 256 X0 SP0 Y0 C0 T0 CT0 S0 X377 SP777 Y377 C777 T177 CT177 S377
Convert PLC Addr. to Dec. 128 128 3968 V0 V1000 V1200 V7600 V177 V1177 V7377 V7777
438
The following examples show how to generate the MODBUS address and data type for hosts which require this format.
Example 1: V2100
Find the MODBUS address for User V location V2100. 1. Find V memory in the table. 2. Convert V2100 into decimal (1088). 3. Use the MODBUS data type from the table.
V Memory, user data (V) 3200 V1200
PLC Address (Dec.) + Data Type V2100 = 1088 decimal 1088 + Hold. Reg. = Holding Reg. 1088
V7377
640
3839
Holding Register
Example 2: Y20
Find the MODBUS address for output Y20. PLC Addr. (Dec) + Start Addr. + Data Type 1. Find Y outputs in the table. Y20 = 16 decimal 2. Convert Y20 into decimal (16). 16 + 2048 + Coil = Coil 2064 3. Add the starting address for the range (2048). 4. Use the MODBUS data type from the table.
Outputs (Y) 256 Y0 Y377 2048 2303 Coil
Example 3: T10 Current Find the MODBUS address to obtain the current value from Timer T10. Value
PLC Address (Dec.) + Data Type T10 = 8 decimal 8 + Input Reg. = Input Reg. 8
1. Find Timer Current Values in the table. 2. Convert T10 into decimal (8). 3. Use the MODBUS data type from the table.
128
V0
V177
127
Input Register
Example 4: C54
Find the MODBUS address for Control Relay PLC Addr. (Dec) + Start Addr. +Data Type C54. C54 = 44 decimal 1. Find Control Relays in the table. 44 + 3072 + Coil = Coil 3116 2. Convert C54 into decimal (44). 3. Add the starting address for the range (3072). 4. Use the MODBUS data type from the table.
Control Relays (CR) 512 C0 C777 3072 3583 Coil
439
Some host software does not allow you to specify the MODBUS data type and address. Instead, you specify an address only. This method requires another step to determine the address, but its still fairly simple. Basically, MODBUS also separates the data types by address ranges as well. So this means an address alone can actually describe the type of data and location. This is often referred to as adding the offset. One important thing to remember here is that two different addressing modes may be available in your host software package. These are: S 484 Mode S 584/984 Mode We recommend that you use the 584/984 addressing mode if your host software allows you to choose. This is because the 584/984 mode allows access to a higher number of memory locations within each data type. If your software only supports 484 mode, then there may be some PLC memory locations that will be unavailable. The actual equation used to calculate the address depends on the type of PLC data you are using. The PLC memory types are split into two categories for this purpose. S Discrete X, SP, Y, CR, S, T, C (contacts) S Word V, Timer current value, Counter current value In either case, you basically convert the PLC octal address to decimal and add the appropriate MODBUS addresses (as required). The table below shows the exact equation used for each group of data.
QTY (Dec.) PLC Range (Octal) MODBUS Address Range (Decimal) Start of Range 2048 3072 2048 3072 6144 6400 5120 0 512 768 3840 3968 + 127 639 3839 3967 4095 2303 3583 2303 3583 6271 6527 5375 484 Mode Address 584/984 Mode Address 10001 10001 1 1 1 1 1 30001 30001 40001 40001 40001 MODBUS Data Type
For Discrete Data Types ... Convert PLC Addr. to Dec. + Inputs (X) Special Relays (SP) Outputs (Y) Control Relays (CR) Timer Contacts (T) Counter Contacts (CT) Stage Status Bits (S) Timer Current Values (V) Counter Current Values (V) V Memory, user data (V) V Memory, system (V) 256 512 256 512 128 128 256 128 128 3200 256 X0 SP0 Y0 C0 T0 CT0 S0 V0 V1000 V1400 V7400 V7600 X377 SP777 Y377 C777 T177 CT177 S377 V377 V1177 V7377 V7577 V7777
+ Appropriate Mode Address 1001 1001 1 1 1 1 1 3001 3001 4001 4001 4001 Input Input Coil
Coil Coil Coil Coil Input Reg. Input Reg Hold Reg. Hold Reg. Hold Reg.
440
The following examples show how to generate the MODBUS addresses for hosts which require this format.
Example 1: V2100 584/984 Mode
Find the MODBUS address for User V location V2100. 1. Find V memory in the table. 2. Convert V2100 into decimal (1088). 3. Add the MODBUS starting address for the mode (40001).
128 V1200 V7377
PLC Address (Dec.) + Mode Address V2100 = 1088 decimal 1088 + 40001 = 41089
3480
3735
4001
40001
Hold Reg.
Find the MODBUS address for output Y20. 1. Find Y outputs in the table. 2. Convert Y20 into decimal (16). 3. Add the starting address for the range (2048). 4. Add the MODBUS address for the mode (1).
Outputs (Y) 256 Y0 Y377
PLC Addr. (Dec) + Start Addr. + Mode Y20 = 16 decimal 16 + 2048 + 1 = 2065
2048
2303
Coil
Example 3: T10 Current Find the MODBUS address to obtain the current value from Timer T10. Value 484 Mode 1. Find Timer Current Values in the table.
2. Convert T10 into decimal (8). 3. Add the MODBUS starting address for the mode (3001).
Timer Current Values (V) 128 V0 V177 0 127 3001 30001 Input Reg.
Find the MODBUS address for Control Relay PLC Addr. (Dec) + Start Address + Mode C54. C54 = 44 decimal 1. Find Control Relays in the table. 44 + 3072 + 1 = 3117 2. Convert C54 into decimal (44). 3. Add the starting address for the range (3072). 4. Add the MODBUS address for the mode (1).
Control Relays (CR) 512 C0 C777 3072 3583 1 1 Coil
Addressing the memory types for DirectNET slaves is very easy. Use the ordinary native address of the slave device itself. To access a slave PLCs memory address V2000 via DirectNET, for example, the network master will request V2000 from the slave.
441
Slave #1
Slave #2
Slave #3
Master
When using the DL05 PLC as the master station, simple RLL instructions are used to initiate the requests. The WX instruction initiates network write operations, and the RX instruction initiates network read operations. Before executing either the WX or RX commands, we will need to load data related to the read or write operation onto the CPUs accumulator stack. When the WX or RX instruction executes, it uses the information on the stack combined with data in the instruction box to completely define the task, which goes to the port. CPU Specifications and Operation
Network
Master
The following step-by-step procedure will provide you the information necessary to set up your ladder program to receive data from a network slave.
442
The first Load (LD) instruction identifies the communications port number on the network master (DL05) and the address of the slave station. This instruction can address up to 99 MODBUS slaves, or 90 DirectNET slaves. The format of the word is shown to the right. The F2 in the upper byte indicates the use of the right port of the DL05 PLC, port number 2. The lower byte contains the slave address number in BCD (01 to 99). The second Load (LD) instruction determines the number of bytes which will be transferred between the master and slave in the subsequent WX or RX instruction. The value to be loaded is in BCD format (decimal), from 1 to 128 bytes.
(BCD)
# of bytes to transfer
LD K128
The number of bytes specified also depends on the type of data you want to obtain. For example, the DL05 Input points can be accessed by V-memory locations or as X input locations. However, if you only want X0 X27, youll have to use the X input data type because the V-memory locations can only be accessed in 2-byte increments. The following table shows the byte ranges for the various types of Direct LOGIC products. DL 05 / 205 / 350 / 405 Memory CPU Specifications and Operation V memory T / C current value Inputs (X, SP) Outputs (Y, C, Stage, T/C bits) Scratch Pad Memory Diagnostic Status DL330 / 340 Memory Data registers T / C accumulator I/O, internal relays, shift register bits, T/C bits, stage bits Scratch Pad Memory Diagnostic Status(5 word R/W) Bits per unit 16 16 8 8 8 8 Bits per unit 8 16 1 8 16 Bytes 2 2 1 1 1 1 Bytes 1 2 1 1 10
443
The third instruction in the RX or WX sequence is a Load Address (LDA) instruction. Its purpose is to load the starting address of the memory area to be transferred. Entered as an octal number, the LDA instruction converts it to hex and places the result in the accumulator. For a WX instruction, the DL05 CPU sends the number of bytes previously specified from its memory area beginning at the LDA address specified. For an RX instruction, the DL05 CPU reads the number of bytes previously specified from the slave, placing the received data into its memory area beginning at the LDA address specified.
(octal)
MSB 15 MSB 15
V40600
LSB 0
V40601
LSB 0
NOTE: Since V memory words are always 16 bits, you may not always use the whole word. For example, if you only specify 3 bytes and you are reading Y outputs from the slave, you will only get 24 bits of data. In this case, only the 8 least significant bits of the last word location will be modified. The remaining 8 bits are not affected. Step 4: Specify Slave Memory Area The last instruction in our sequence is the WX or RX instruction itself. Use WX to write to the slave, and RX to read from the slave. All four of our instructions are shown to the right. In the last instruction, you must specify the starting address and a valid data type for the slave.
SP116 LD KF201 LD K128 LDA O40600
RX Y0
S S S
DirectNET slaves specify the same address in the WX and RX instruction as the slaves native I/O address MODBUS DL405, DL205, or DL05 slaves specify the same address in the WX and RX instruction as the slaves native I/O address MODBUS 305 slaves use the following table to convert DL305 addresses to MODBUS addresses
DL305 Series CPU Memory TypetoMODBUS Cross Reference (excluding 350 CPU)
PLC Memory type TMR/CNT Current Values I/O Points Data Registers Stage Status Bits (D3330P only) PLC base address R600 IO 000 R401, R400 S0 MODBUS base addr. V0 GY0 V100 GY200 PLC Memory Type TMR/CNT Status Bits Control Relays Shift Registers PLC base address CT600 CR160 SR400 MODBUS base addr. GY600 GY160 GY400
444
Typically network communications will last longer than 1 scan. The program must wait for the communications to finish before starting the next transaction.
Port Communication Error
SP117
SP116
Port Busy
Port 2, which can be a master, has two Special Relay contacts associated with it (see Appendix D for comm port special relays).One indicates Port busy(SP116), and the other indicates Port Communication Error(SP117). The example above shows the use of these contacts for a network master that only reads a device (RX). The Port Busy bit is on while the PLC communicates with the slave. When the bit is off the program can initiate the next network request. The Port Communication Error bit turns on when the PLC has detected an error. Use of this bit is optional. When used, it should be ahead of any network instruction boxes since the error bit is reset when an RX or WX instruction is executed. Multiple Read and Write Interlocks If you are using multiple reads and writes in the RLL program, you have to interlock the routines to make sure all the routines are executed. If you dont use the interlocks, then the CPU will only execute the first routine. This is because each port can only handle one transaction at a time. In the example to the right, after the RX instruction is executed, C0 is set. When the port has finished the communication task, the second routine is executed and C0 is reset. If youre using RLL PLUS Stage Programing, you can put each routine in a separate program stage to ensure proper execution and switch from stage to stage allowing only one of them to be active at a time.
Interlocking Relay
SP116 C100 LD KF201 LD K0003 LDA O40600 RX Y0 C100 SET LD KF201 LD K0003 LDA O40400 WX Y0 C100 RST
Interlocking Relay
SP116 C100
15
Boolean Instructions Comparative Boolean Immediate Instructions Timer, Counter and Shift Register Instructions Accumulator / Stack Load and Output Data Instructions Logical Instructions (Accumulator) Math Instructions Bit Operation Instructions (Accumulator) Number Conversion Instructions (Accumulator) Table Instructions CPU Control Instructions Program Control Instructions Interrupt Instructions Message Instructions
52
Introduction
DL05 Micro PLCs offer a wide variety of instructions to perform many different types of operations. This chapter shows you how to use each standard Relay Ladder Logic (RLL) instruction. In addition to these instructions, you may also need to refer to the Drum instruction in Chapter 6, or the Stage programming instructions in Chapter 7. There are two ways to quickly find the instruction you need. S S
Instruction ACON ADDB ADD ADDD AND AND STR ANDD ANDE ANDI ANDN ANDND ANDNE ANDNI ANDPD ATH BCD BIN CMP CMPD CNT CV CVJMP DEC DECB Page 5107 573 563 564 511, 555 512 556 522 527 511, 525 517 522 527 517 585 583 582 561 562 536 723 723 571 572 581 5104 569 576 570 5107 612 62, 614 525,
If you know the instruction category (Boolean, Comparative Boolean, etc.) just use the title at the top of the page to find the pages that discuss the instructions in that category. If you know the individual instruction name, use the following table to find the page(s) that discusses the instruction.
Instruction ENCO END ENI FAULT FOR GRAY GTS HTA INC INCB INT INV IRT IRTC ISG JMP LD LDA LDD LDF LDLBL MLR MLS MOV MOVMC MUL MULB MULD NCON NEXT NJMP NOP NOT 580 594 5103 5106 596 588 598 586 571 572 5103 584 5103 5103 722 722 548 551 549 550 592 5101 5101 591 592 567 575 568 5107 596 722 594 514 OR OUT ORE ORI ORN ORND ORNE OR OUTI OR STR ORD ORNI OROUTI ORPD OUT OUTD OUTF OUTI PAUSE PD POP PRINT RST RSTI RSTWT RT RTC RX SBR SET SETI SFLDGT SG SGCNT Page OR Instruction Page 510, 557 513 521 526 510, 524 516 521 528 512 558 526 528 516 513, 552 552 553 528 519 514 553 5109 518 529 595 598 598 5113 598 518 529 589 721 538 524,
Instruction Set
53
Page
Instruction SHFL SHFR SR STOP STR STRE STRI STRN 577 579 542 594
Page
Instruction STRND STRNE STRNI STRPD SUB SUBB SUBD SUM 515 520 526 515 565 574 566 577
Page TMR
Instruction 531 533 533 531 540 TMRA TMRAF TMRF UDC WX XOR XORD
54
END Statement
OUT
END
Simple Rungs
You use a contact to start rungs that contain both contacts and coils. The boolean instruction that does this is called a Store or, STR instruction. The output point is represented by the Output or, OUT instruction. The following example shows how to enter a single contact and a single output coil.
DirectSOFT Example
X0 Y0 OUT Handheld Mnemonics STR X0 OUT Y0 END
END
Normally closed contacts are also very common. This is accomplished with the Store Not or, STRN instruction. The following example shows a simple rung with a normally closed contact.
DirectSOFT Example
X0 Y0 OUT Handheld Mnemonics STRN X0 OUT Y0 END
END
55
Contacts in Series
Use the AND instruction to join two or more contacts in series. The following example shows two contacts in series and a single output coil. The instructions used would be STR X0, AND X1, followed by OUT Y0.
DirectSOFT Example
X0 X1 Y0 OUT Handheld Mnemonics STR X0 AND X1 OUT Y0 END
END
Midline Outputs
Sometimes it is necessary to use midline outputs to get additional outputs that are conditional on other contacts. The following example shows how you can use the AND instruction to continue a rung with more conditional outputs.
DirectSOFT Example
X0 X1 Y0 OUT X2 Y1 OUT X3 Y2 OUT Handheld Mnemonics STR X0 AND X1 OUT Y0 AND X2 OUT Y1 AND X3 OUT Y2 END
END
Parallel Elements
You also have to join contacts in parallel. The OR instruction allows you to do this. The following example shows two contacts in parallel and a single output coil. The instructions would be STR X0, OR X1, followed by OUT Y0.
DirectSOFT Example
X0 Y0 OUT X1 Handheld Mnemonics STR X0 OR X1 OUT Y0 END
END
56
Quite often it is necessary to join several groups of series elements in parallel. The Or Store (ORSTR) instruction allows this operation. The following example shows a simple network consisting of series elements joined in parallel.
DirectSOFT Example
X0 X1 Y0 OUT X2 X3 Handheld Mnemonics STR X0 AND X1 STR X2 AND X3 ORSTR OUT Y0 END
END
You can also join one or more parallel branches in series. The And Store (ANDSTR) Joining Parallel Branches in Series instruction allows this operation. The following example shows a simple network with contact branches in series with parallel contacts.
DirectSOFT Example
X0 X1 Y0 OUT X2 Handheld Mnemonics STR X0 STR X1 OR X2 ANDSTR OUT Y0 END
END
Combination Networks
You can combine the various types of series and parallel branches to solve most any application problem. The following example shows a simple combination network.
X0 X2 X5 Y0 OUT X1 X3 X4
X6
END
Some PLC manufacturers make it really difficult to do a simple comparison of two numbers. Some of them require you to move the data all over the place before you can actually perform the comparison. The DL05 Micro PLCs provide Comparative Boolean instructions that allow you to quickly and easily solve this problem. The Comparative Boolean provides evaluation of two 4-digit values using boolean contacts. The valid evaluations are: equal to, not equal to, equal to or greater than, and less than. In the following example when the value in V-memory location V1400 is equal to the constant value 1234, Y3 will energize.
V1400 K1234 Y3 OUT
57
Boolean Stack
There are limits to how many elements you can include in a rung. This is because the DL05 PLCs use an 8-level boolean stack to evaluate the various logic elements. The boolean stack is a temporary storage area that solves the logic for the rung. Each time the program encounters a STR instruction, the instruction is placed on the top of the stack. Any other STR instructions already on the boolean stack are pushed down a level. The ANDSTR, and ORSTR instructions combine levels of the boolean stack when they are encountered. An error will occur during program compilation if the CPU encounters a rung that uses more than the eight levels of the boolean stack. The following example shows how the boolean stack is used to solve boolean logic.
X0
STR
STR
X1
ORSTR
AND X4
Y0 OUT
Output
X2
STR
X5
AND X3
ANDSTR
OR
STR X2
1 2 3 4 5 6 7 8 STR X2 STR X1 STR X0
STR X0
1 2 3 4 5 6 7 8 STR X0
STR X1
1 2 3 4 5 6 7 8 STR X1 STR X0
AND X3
1 2 3 4 5 6 7 8 X2 AND X3 STR X1 STR X0
ORSTR
1 2 3
S S
AND X4
1 2 3
S S
ORNOT X5
1 2 3
S S
ANDSTR
1 2 3
S S
58
Immediate Boolean The DL05 Micro PLCs can usually complete an operation cycle in a matter of milliseconds. However, in some applications you may not be able to wait a few milliseconds until the next I/O update occurs. The DL05 PLCs offer Immediate input and outputs which are special boolean instructions that allow reading directly from inputs and writing directly to outputs during the program execution portion of the CPU cycle. You may recall that this is normally done during the input or output update portion of the CPU cycle. The immediate instructions take longer to execute because the program execution is interrupted while the CPU reads or writes the I/O point. This function is not normally done until the read inputs or the write outputs portion of the CPU cycle. NOTE: Even though the immediate input instruction reads the most current status from the input point, it only uses the results to solve that one instruction. It does not use the new status to update the image register. Therefore, any regular instructions that follow will still use the image register values. Any immediate instructions that follow will access the I/O again to update the status. The immediate output instruction will write the status to the I/O and update the image register.
CPU Scan
Read Inputs
X11 OFF ... X2 X1 X0 ... ON OFF OFF Input Image Register The CPU reads the inputs from the local base and stores the status in an input image register.
OFF OFF
X0 X1
Immediate instruction does not use the input image register, but instead reads the status from the module immediately.
59
Boolean Instructions
Store (STR) The Store instruction begins a new rung or an additional branch in a rung with a normally open contact. Status of the contact will be the same state as the associated image register point or memory location. The Store Not instruction begins a new rung or an additional branch in a rung with a normally closed contact. Status of the contact will be opposite the state of the associated image register point or memory location.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter Special Relay X Y C S T CT SP DL05 Range aaa 0377 0377 0777 0377 0177 0177 0777
Aaaa
Aaaa
In the following Store example, when input X1 is on, output Y2 will energize.
DirectSOFT
X1 Y2 OUT Handheld Programmer Keystrokes $ STR GX OUT C 2 B 1 ENT ENT
In the following Store Not example, when input X1 is off output Y2 will energize.
DirectSOFT
X1 Y2 OUT Handheld Programmer Keystrokes SP STRN GX OUT B 1 C 2 ENT ENT
510
Or (OR)
The Or instruction logically ors a normally open contact in parallel with another contact in a rung. The status of the contact will be the same state as the associated image register point or memory location. The Or Not instruction logically ors a normally closed contact in parallel with another contact in a rung. The status of the contact will be opposite the state of the associated image register point or memory location.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter Special Relay X Y C S T CT SP DL05 Range aaa 0377 0377 0777 0377 0177 0177 0777
Aaaa
Or Not (ORN)
Aaaa
In the following Or Not example, when input X1 is on or X2 is off, output Y5 will energize.
DirectSOFT
X1 Y5 OUT X2 Handheld Programmer Keystrokes $ STR R ORN GX OUT C 2 F 5 B 1 ENT ENT ENT
511
And (AND)
The And instruction logically ands a normally open contact in series with another contact in a rung. The status of the contact will be the same state as the associated image register point or memory location. The And Not instruction logically ands a normally closed contact in series with another contact in a rung. The status of the contact will be opposite the state of the associated image register point or memory location.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter Special Relay X Y C S T CT SP DL05 Range aaa 0377 0377 0777 0377 0177 0177 0777
Aaaa
Aaaa
In the following And example, when input X1 and X2 are on output Y5 will energize.
DirectSOFT
X1 X2 Y5 OUT Handheld Programmer Keystrokes $ STR V AND GX OUT C 2 F 5 B 1 ENT ENT ENT
In the following And Not example, when input X1 is on and X2 is off output Y5 will energize.
DirectSOFT
X1 X2 Y5 OUT Handheld Programmer Keystrokes $ STR W ANDN GX OUT C 2 F 5 B 1 ENT ENT ENT
512
The And Store instruction logically ands two branches of a rung in series. Both branches must begin with the Store instruction.
OUT
The Or Store instruction logically ors two branches of a rung in parallel. Both branches must begin with the Store instruction.
OUT
In the following And Store example, the branch consisting of contacts X2, X3, and X4 have been anded with the branch consisting of contact X1.
DirectSOFT
X1 X2 X3 Y5 OUT $ X4 STR V AND Q OR L ANDST GX OUT ENT F 5 ENT D 3 E 4 Handheld Programmer Keystrokes $ STR C 2 B 1 ENT ENT ENT ENT
In the following Or Store example, the branch consisting of X1 and X2 have been ored with the branch consisting of X3 and X4.
DirectSOFT
X1 X2 Y5 OUT X3 X4 Handheld Programmer Keystrokes $ STR V AND $ STR V AND M ORST GX OUT ENT F 5 ENT E 4 C 2 D 3 B 1 ENT ENT ENT ENT
513
Out (OUT)
The Out instruction reflects the status of the rung (on/off) and outputs the discrete (on/off) state to the specified image register point or memory location.
Aaaa OUT
Multiple Out instructions referencing the same discrete location should not be used since only the last Out instruction in the program will control the physical output point. Instead, use the next instruction, the Or Out.
Operand Data Type A Inputs Outputs Control Relays X Y C DL05 Range aaa 0377 0377 0777
In the following Out example, when input X1 is on, output Y2 and Y5 will energize.
DirectSOFT
X1 Y2 OUT Y5 OUT Handheld Programmer Keystrokes $ STR GX OUT GX OUT C 2 F 5 B 1 ENT ENT ENT
The Or Out instruction allows more than one rung of discrete logic to control a single output. Multiple Or Out instructions referencing the same output coil may be used, since all contacts controlling the output are logically ORed together. If the status of any rung is on, the output will also be on.
Operand Data Type A Inputs Outputs Control Relays X Y C DL05 Range aaa 0177 0177 0777
A aaa OR OUT
In the following example, when X1 or X4 is on, Y2 will energize. Standard RLL Instructions
DirectSOFT
X1 Y2 OR OUT Handheld Programmer Keystrokes $ STR O INST# $ STR X4 Y2 OR OUT O INST# D 3 F 5 D 3 E 4 F 5 B 1
514
Not (NOT)
The Not instruction inverts the status of the rung at the point of the instruction.
In the following example when X1 is off, Y2 will energize. This is because the Not instruction inverts the status of the rung at the Not instruction.
DirectSOFT
X1 Y2 OUT SHFT GX OUT Handheld Programmer Keystrokes $ STR N TMR B 1 O INST# C 2 ENT T MLR ENT ENT
NOTE: DirectSOFT Release 1.1i and later supports the use of the NOT instruction. The above example rung is merely intended to show the visual representation of the NOT instruction. The rung cannot be created or displayed in DirectSOFT versions earlier than 1.1i. Positive Differential (PD) The Positive Differential instruction is typically known as a one shot. When the input logic produces an off to on transition, the output will energize for one CPU scan.
A aaa PD
In the following example, every time X1 makes an off to on transition, C0 will energize for one scan.
DirectSOFT
X1 C0 PD SHFT Handheld Programmer Keystrokes $ STR P CV B 1 SHFT ENT D 3 A 0 ENT
515
The Store Positive Differential instruction begins a new rung or an additional branch in a rung with a normally open contact. The contact closes for one CPU scan when the state of the associated image register point makes an Off-to-On transition. Thereafter, the contact remains open until the next Off-to-On transition (the symbol inside the contact represents the transition). This function is sometimes called a one-shot. The Store Negative Differential instruction begins a new rung or an additional branch in a rung with a normally closed contact. The contact closes for one CPU scan when the state of the associated image register point makes an On-to-Off transition. Thereafter, the contact remains open until the next On-to-Off transition (the symbol inside the contact represents the transition).
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter X Y C S T CT DL05 Range aaa 0377 0377 0777 0377 0177 0177
Aaaa
Aaaa
In the following example, each time X1 is makes an Off-to-On transition, Y4 will energize for one scan.
DirectSOFT
X1 Y4 OUT Handheld Programmer Keystrokes $ STR GX OUT SHFT P CV E 4 D 3 ENT B 1 ENT
In the following example, each time X1 is makes an On-to-Off transition, Y4 will energize for one scan. Standard RLL Instructions
DirectSOFT
X1 Y4 OUT Handheld Programmer Keystrokes $ STR GX OUT SHFT N TMR E 4 D 3 ENT B 1 ENT
516
The Or Positive Differential instruction logically ors a normally open contact in parallel with another contact in a rung. The status of the contact will be open until the associated image register point makes an Off-to-On transition, closing it for one CPU scan. Thereafter, it remains open until another Off-to-On transition. The Or Negative Differential instruction logically ors a normally open contact in parallel with another contact in a rung. The status of the contact will be open until the associated image register point makes an On-to-Off transition, closing it for one CPU scan. Thereafter, it remains open until another On-to-Off transition.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter X Y C S T CT DL05 Range aaa 0377 0377 0777 0377 0177 0177
Aaaa
Aaaa
In the following example, Y 5 will energize whenever X1 is on, or for one CPU scan when X2 transitions from Off to On.
DirectSOFT
X1 Y5 OUT X2 Handheld Programmer Keystrokes $ STR Q OR GX OUT SHFT P CV F 5 B 1 ENT D 3 ENT C 2 ENT
In the following example, Y 5 will energize whenever X1 is on, or for one CPU scan when X2 transitions from On to Off.
DirectSOFT
X1 Y5 OUT Handheld Programmer Keystrokes $ STR Q OR GX OUT SHFT B 1 N TMR F 5 ENT D 3 ENT C 2 ENT
X2
517
The And Positive Differential instruction logically ands a normally open contact in parallel with another contact in a rung. The status of the contact will be open until the associated image register point makes an Off-to-On transition, closing it for one CPU scan. Thereafter, it remains open until another Off-to-On transition. The And Negative Differential instruction logically ands a normally open contact in parallel with another contact in a rung. The status of the contact will be open until the associated image register point makes an On-to-Off transition, closing it for one CPU scan. Thereafter, it remains open until another On-to-Off transition.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter X Y C S T CT DL05 Range aaa 0377 0377 0777 0377 0177 0177
Aaaa
Aaaa
In the following example, Y5 will energize for one CPU scan whenever X1 is on and X2 transitions from Off to On.
DirectSOFT
X1 X2 Y5 OUT Handheld Programmer Keystrokes $ STR Q OR GX OUT SHFT P CV F 5 B 1 ENT D 3 ENT C 2 ENT
In the following example, Y5 will energize for one CPU scan whenever X1 is on and X2 transitions from On to Off.
DirectSOFT
X1 X2 Y5 OUT Handheld Programmer Keystrokes $ STR Q OR GX OUT SHFT B 1 N TMR F 5 ENT D 3 ENT C 2 ENT
518
Set (SET)
The Set instruction sets or turns on an image register point/memory location or a consecutive range of image register points/memory locations. Once the point/location is set it will remain on until it is reset using the Reset instruction. It is not necessary for the input controlling the Set instruction to remain on. The Reset instruction resets or turns off an image register point/memory location or a range of image registers points/memory locations. Once the point/location is reset it is not necessary for the input to remain on.
Operand Data Type A Inputs Outputs Control Relays Stage Timer Counter X Y C S T CT DL05 Range aaa 0377 0377 0777 0377 0177 0177
Reset (RST)
519
Pause (PAUSE)
The Pause instruction disables the output update on a range of outputs. The ladder program will continue to run and update the image register. However, the outputs in the range specified in the Pause instruction will be turned off at the output points.
Operand Data Type DL05 Range aaa Outputs Y 0377
In the following example, when X1 is ON, Y3Y5 will be turned OFF. The execution of the ladder program will not be affected.
DirectSOFT
X1 Y5 Y7
PAUSE
Since the D2HPP Handheld Programmer does not have a specific Pause key, you can use the corresponding instruction number for entry (#960), or type each letter of the command.
Handheld Programmer Keystrokes $ STR O INST# J 9 G 6 B 1 ENT A 0 ENT ENT D 3 F 5 ENT
In some cases, you may want certain output points in the specified pause range to operate normally. In that case, use Aux 58 to over-ride the Pause instruction.
520
Comparative Boolean
Store If Equal (STRE) The Store If Equal instruction begins a new rung or additional branch in a rung with a normally open comparative contact. The contact will be on when Vaaa =Bbbb . The Store If Not Equal instruction begins a new rung or additional branch in a rung with a normally closed comparative contact. The contact will be on when Vaaa Bbbb.
Operand Data Type B V memory Pointer Constant V P K aaa All (See page 428) All (See page 428) DL05 Range bbb All (See page 428) All (See page 428) 09999
V aaa
B bbb
V aaa
B bbb
In the following example, when the value in V memory location V2000 = 4933 , Y3 will energize.
DirectSOFT
V2000 K4933 Y3 OUT Handheld Programmer Keystrokes $ STR SHFT E 4 GX OUT D 3 E 4 J 9 D 3 ENT D 3 C 2 A 0 ENT A 0 A 0
In the following example, when the value in V memory location V2000 5060, Y3 will energize.
DirectSOFT
V2000 K5060 Y3 OUT Handheld Programmer Keystrokes SP STRN SHFT F 5 GX OUT D 3 E 4 A 0 G 6 ENT A 0 C 2 A 0 ENT A 0 A 0
521
Or If Equal (ORE)
The Or If Equal instruction connects a normally open comparative contact in parallel with another contact. The contact will be on when Vaaa = Bbbb.
V aaa
B bbb
The Or If Not Equal instruction connects a normally closed comparative contact in parallel with another contact. The contact will be on when Vaaa Bbbb.
V aaa
B bbb
DL05 Range bbb All (See page 428) All (See page 428) 09999
In the following example, when the value in V memory location V2000 = 4500 or V2002 = 2345 , Y3 will energize.
DirectSOFT
V2000 K4500 Y3 OUT Handheld Programmer Keystrokes $ STR E 4 V2002 K2345 Q OR C 2 GX OUT SHFT F 5 SHFT D 3 D 3 E 4 E 4 F 5 ENT E 4 A 0 A 0 C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
In the following example, when the value in V memory location V2000 = 3916 or V2002 050, Y3 will energize.
DirectSOFT
V2000 K3916 Y3 OUT Handheld Programmer Keystrokes $ STR D 3 V2002 K2500 R ORN C 2 GX OUT SHFT J 9 SHFT F 5 D 3 E 4 A 0 A 0 ENT E 4 B 1 G 6 C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
522
The And If Equal instruction connects a normally open comparative contact in series with another contact. The contact will be on when Vaaa = Bbbb.
V aaa
B bbb
The And If Not Equal instruction connects a normally closed comparative contact in series with another contact. The contact will be on when Vaaa Bbbb
V aaa
B bbb
DL05 Range bbb All (See page 428) All (See page 428) 09999
In the following example, when the value in V memory location V2000 = 5000 and V2002 = 2345, Y3 will energize.
DirectSOFT
V2000 K5000 V2002 K2345 Y3 OUT Handheld Programmer Keystrokes $ STR F 5 V AND C 2 GX OUT SHFT A 0 SHFT D 3 D 3 E 4 E 4 F 5 ENT E 4 A 0 A 0 C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
In the following example, when the value in V memory location V2000 = 2550 and V2002 050, Y3 will energize.
DirectSOFT
V2000 K2550 V2002 K2500 Y3 OUT Handheld Programmer Keystrokes $ STR C 2 W ANDN C 2 GX OUT SHFT F 5 SHFT F 5 D 3 E 4 A 0 A 0 ENT E 4 F 5 A 0 C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
523
Store (STR)
The Comparative Store instruction begins a new rung or additional branch in a rung with a normally open comparative contact. The contact will be on when Aaaa Bbbb. The Comparative Store Not instruction begins a new rung or additional branch in a rung with a normally closed comparative contact. The contact will be on when Aaaa < Bbbb.
Operand Data Type A/B V memory Pointer Constant Timer Counter V P K T CT aaa All (See page 428) All (See page 428) 0177 0177 DL05 Range bbb All (See page 428) All (See page 428) 09999
A aaa
B bbb
A aaa
B bbb
In the following example, when the value in V memory location V2000 1000, Y3 will energize.
DirectSOFT
V2000 K1000 Y3 OUT Handheld Programmer Keystrokes $ STR B 1 GX OUT D 3 SHFT A 0 V AND A 0 ENT C 2 A 0 A 0 ENT A 0 A 0
In the following example, when the value in V memory location V2000 < 4050, Y3 will energize.
DirectSOFT
V2000 K4050 Y3 OUT Handheld Programmer Keystrokes SP STRN E 4 GX OUT D 3 SHFT A 0 V AND F 5 ENT C 2 A 0 A 0 ENT A 0 A 0
524
Or (OR)
The Comparative Or instruction connects a normally open comparative contact in parallel with another contact. The contact will be on when Aaaa Bbbb. The Comparative Or Not instruction connects a normally open comparative contact in parallel with another contact. The contact will be on when Aaaa < Bbbb.
A aaa
B bbb
Or Not (ORN)
A aaa
B bbb
Operand Data Type A/B V memory Pointer Constant Timer Counter V P K T CT aaa
DL05 Range bbb All (See page 428) All (See page 428) 09999
All (See page 428) All (See page 428) 0177 0177
In the following example, when the value in V memory location V2000 = 6045 or V2002 2345, Y3 will energize.
DirectSOFT
V2000 K6045 Y3 OUT Handheld Programmer Keystrokes $ STR G 6 V2002 K2345 Q OR C 2 GX OUT D 3 D 3 SHFT A 0 E 4 E 4 SHFT E 4 F 5 V AND F 5 ENT C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
In the following example when the value in V memory location V2000 = 1000 or V2002 < 050, Y3 will energize.
DirectSOFT
V2000 K1000 Y3 OUT Handheld Programmer Keystrokes $ STR B 1 V2002 K2500 R ORN C 2 GX OUT F 5 D 3 SHFT A 0 E 4 A 0 SHFT A 0 A 0 V AND A 0 ENT C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
525
And (AND)
The Comparative And instruction connects a normally open comparative contact in series with another contact. The contact will be on when Aaaa Bbbb. The Comparative And Not instruction connects a normally open comparative contact in parallel with another contact. The contact will be on when Aaaa < Bbbb.
Operand Data Type A/B V memory Pointer Constant Timer Counter V P K T CT aaa All (See page 428) All (See page 428) 0177 0177 DL05 Range bbb All (See page 428) All (See page 428) 09999
A aaa
B bbb
A aaa
B bbb
In the following example, when the value in V memory location V2000 = 5000, and V2002 2345, Y3 will energize.
DirectSOFT
V2000 K5000 V2002 K2345 Y3 OUT Handheld Programmer Keystrokes $ STR F 5 V AND C 2 GX OUT D 3 D 3 SHFT A 0 E 4 A 0 SHFT E 4 A 0 V AND F 5 ENT C 2 ENT C 2 ENT A 0 A 0 C 2 A 0 A 0 A 0
In the following example, when the value in V memory location V2000 = 7000 and V2002 < 050, Y3 will energize.
DirectSOFT
V2000 K7000 V2002 K2500 Y3 OUT Handheld Programmer Keystrokes $ STR H 7 W ANDN C 2 GX OUT F 5 SHFT A 0 E 4 A 0 SHFT A 0 SHFT A 0 V AND A 0 Y AND C 2 ENT C 2 ENT D 3 ENT A 0 A 0 C 2 A 0 A 0 A 0
526
Immediate Instructions
Store Immediate (STRI) The Store Immediate instruction begins a new rung or additional branch in a rung. The status of the contact will be the same as the status of the associated input point at the time the instruction is executed. The image register is not updated. The Store Not Immediate instruction begins a new rung or additional branch in a rung. The status of the contact will be opposite the status of the associated input point at the time the instruction is executed. The image register is not updated.
Operand Data Type DL05 Range aaa Inputs X 0377
X aaa
X aaa
Or Immediate (ORI)
The Or Immediate connects two contacts in parallel. The status of the contact will be the same as the status of the associated input point at the time the instruction is executed. The image register is not updated. The Or Not Immediate connects two contacts in parallel. The status of the contact will be opposite the status of the associated input point at the time the instruction is executed. The image register is not updated.
X aaa
X aaa
527
Inputs
0377
The And Immediate connects two contacts in series. The status of the contact will be the same as the status of the associated input point at the time the instruction is executed. The image register is not updated. The And Not Immediate connects two contacts in series. The status of the contact will be opposite the status of the associated input point at the time the instruction is executed. The image register is not updated.
Operand Data Type DL05 Range aaa Inputs X 0377
X aaa
X aaa
528
The Out Immediate instruction reflects the status of the rung (on/off) and outputs the discrete (on/off) status to the specified module output point and the image register at the time the instruction is executed. If multiple Out Immediate instructions referencing the same discrete point are used it is possible for the module output status to change multiple times in a CPU scan. See Or Out Immediate. The Or Out Immediate instruction has been designed to use more than 1 rung of discrete logic to control a single output. Multiple Or Out Immediate instructions referencing the same output coil may be used, since all contacts controlling the output are ored together. If the status of any rung is on at the time the instruction is executed, the output will also be on.
Operand Data Type DL05 Range aaa Outputs Y 0377
Y aaa OUTI
Y aaa OROUTI
In the following example, when X1 is on, output point Y2 on the output module will turn on. For instruction entry on the Handheld Programmer, you can use the instruction number (#350) as shown, or type each letter of the command.
DirectSOFT
X1 Y2 OUTI Handheld Programmer Keystrokes $ STR O INST# D 3 C 2 F 5 ENT B 1 ENT A 0 ENT ENT
X4
Y2 OR OUTI
529
The Set Immediate instruction immediately sets, or turns on an output or a range of outputs in the image register and the corresponding output point(s) at the time the instruction is executed. Once the outputs are set it is not necessary for the input to remain on. The Reset Immediate instruction can be used to reset the outputs. The Reset Immediate instruction immediately resets, or turns off an output or a range of outputs in the image register and the output point(s) at the time the instruction is executed. Once the outputs are reset it is not necessary for the input to remain on.
Operand Data Type DL05 Range aaa Outputs Y 0377
In the following example, when X1 is on, Y2 through Y5 will be set on in the image register and on the corresponding output points.
DirectSOFT
X1 Y2 Y5 SETI Handheld Programmer Keystrokes $ STR X SET SHFT I 8 B 1 ENT C 2 F 5 ENT
In the following example, when X1 is on, Y5 through Y22 will be reset (off) in the image register and on the corresponding output module(s).
DirectSOFT
X1 Y2 Y5 RSTI Handheld Programmer Keystrokes $ STR S RST SHFT I 8 B 1 ENT C 2 F 5 ENT
530
0 X1
Timer preset
Y0 OUT
There are those applications that need an accumulating timer, meaning it has the ability to time, stop, and then resume from where it previously stopped. The accumulating timer works similarly to the regular timer, but two inputs are required. The start/stop input starts and stops the timer. When the timer stops, the elapsed time is maintained. When the timer starts again, the timing continues from the elapsed time. When the reset input is turned on, the elapsed time is cleared and the timer will start at 0 when it is restarted. There is a tenth of a second and a hundredth of a second timer available with a maximum time of 9999999.9 and 999999.99 seconds respectively. The timing diagram below shows the relationship between the timer input, timer reset, associated discrete bit, current value, and timer preset.
0 X1 1 2 3 Seconds 4 5 6 7 8 X1 TMRA K30 T0
Start/Stop
X2
X2
Reset Input
T0 Current Value 0 10 10 20 30 1/10 Seconds 40 50 0
531
The Timer instruction is a 0.1 second single input timer that times to a maximum of 999.9 seconds. The Timer Fast instruction is a 0.01 second single input timer that times up to a maximum of 99.99 seconds. These timers will be enabled if the input logic is true (on) and will be reset to 0 if the input logic is false (off). Instruction Specifications Timer Reference (Taaa): Specifies the timer number. Preset Value (Bbbb): Constant value (K) or a V memory location. Current Value: Timer current values are accessed by referencing the associated V or T memory location*. For example, the timer current value for T3 physically resides in V-memory location V3. Discrete Status Bit: The discrete status bit is referenced by the associated T memory location. Operating as a timer done bit, it will be on if the current value is equal to or greater than the preset value. For example, the discrete status bit for Timer 2 is TA2.
TMR B bbb
T aaa
Preset
Timer #
Preset
Timer #
The timer discrete status bit and the current value are not specified in the timer instruction.
NOTE: Timer preset constants (K) may be changed by using a handheld programmer, even when the CPU is in Run Mode. Therefore, a V-memory preset is required only if the ladder program must change the preset.
Operand Data Type A/B Timers V memory for preset values Pointers (preset only) Constants (preset only) Timer discrete status bits Timer current values T V P K aaa 0177 DL05 Range bbb 12007377 74007577 12007377 74007577 09999
T/V V /T*
NOTE: * With the HPP, both the Timer discrete status bits and current value are accessed with the same data reference. DirectSOFT uses separate references, such as T2 for discrete status bit for Timer T2, and TA2 for the current value of Timer T2. You can perform functions when the timer reaches the specified preset using the discrete status bit. Or, use comparative contacts to perform functions at different time intervals, based on one timer. The examples on the following page show these two methods of programming timers.
532
In the following example, a single input timer is used with a preset of 3 seconds. The timer discrete status bit (T2) will turn on when the timer has timed for 3 seconds. The timer is reset when X1 turns off, turning the discrete status bit off and resetting the timer current value to 0.
Timing Diagram
TMR K30 T2 X1 0 1 2 3 Seconds 4 5 6 7 8
T2
Y0 OUT
T2
Handheld Programmer Keystrokes $ STR N TMR $ STR GX OUT C 2 SHFT A 0 T MLR ENT C 2 B 1 ENT D 3 A 0 ENT ENT
Timer Example In the following example, a single input timer is used with a preset of 4.5 seconds. Using Comparative Comparative contacts are used to energize Y3, Y4, and Y5 at one second intervals respectively. When X1 is turned off the timer will be reset to 0 and the comparative Contacts contacts will turn off Y3, Y4, and Y5.
DirectSOFT
X1 TMR K45 TA20 K10 Y3 OUT X1 Y3 Y4 Y5 TA20 K30 Y5 OUT T2 Current Value Handheld Programmer Keystrokes $ STR N TMR $ STR GX OUT C 2 SHFT D 3 SHFT E 4 SHFT F 5 B 1 ENT A 0 T MLR ENT T MLR ENT T MLR ENT C 2 A 0 D 3 A 0 ENT C 2 A 0 C 2 A 0 ENT C 2 A 0 E 4 F 5 ENT B 1 A 0 ENT 0 10 20 30 1/10 Seconds 40 50 60 0 T20
Timing Diagram
Seconds 0 1 2 3 4 5 6 7 8
TA20
K20
Y4 OUT
533
The Accumulating Timer is a 0.1 second two input timer that will time to a maximum of 9999999.9. The Accumulating Fast Accumulating Fast Timer is a 0.01 second two-input timer that will time to a maximum of 99999.99. Each Timer (TMRAF) one uses two timer registers in V-memory. These timers have two inputs, an enable and a reset. The timer starts timing when the enable is on and stops when the enable is off (without resetting the count). The reset will reset the timer when on and allow the timer to time when off. Instruction Specifications Timer Reference (Taaa): Specifies the timer number. Preset Value (Bbbb): Constant value (K) or a V memory location. Current Value: Timer current values are accessed by referencing the associated V or T memory location*. For example, the timer current value for T3 resides in V-memory location V3. Discrete Status Bit: The discrete status bit is accessed by referencing the associated T memory location. Operating as a timer done bit ,it will be on if the current value is equal to or greater than the preset value. For example the discrete status bit for timer 2 would be T2.
Enable
Reset
Preset
Timer #
Enable
Reset
Preset
Timer #
The timer discrete status bit and the current value are not specified in the timer instruction.
NOTE: The accumulating type timer uses two consecutive V-memory locations for the 8-digit value, and therefore two consecutive timer locations. For example, if TMR 1 is used, the next available timer number is TMR 3.
Operand Data Type A/B Timers V memory for preset values Pointers (preset only) Constants (preset only) Timer discrete status bits Timer current values T V P K aaa 0176 DL05 Range bbb 12007377 74007577 12007377 74007577 099999999
T/V V /T*
NOTE: * With the HPP, both the Timer discrete status bits and current value are accessed with the same data reference. DirectSOFT uses separate references, such as T2 for discrete status bit for Timer T2, and TA2 for the current value of Timer T2. The following examples show two methods of programming timers. One performs functions when the timer reaches the preset value using the discrete status bit, or use comparative contacts to perform functions at different time intervals.
534
In the following example, a two input timer (accumulating timer) is used with a preset of 3 seconds. The timer discrete status bit (T6) will turn on when the timer has timed for 3 seconds. Notice in this example that the timer times for 1 second , stops for one second, then resumes timing. The timer will reset when C10 turns on, turning the discrete status bit off and resetting the timer current value to 0.
Timing Diagram
TMRA K30 T6 X1 C10 0 1 2 3 Seconds 4 5 6 7 8
C10
T6
Y7 OUT
T6 Current Value 0 10 10 20 1/10 Seconds Handheld Programmer Keystrokes (cont) D 3 A 0 ENT SHFT B 1 T MLR A 0 G 6 ENT ENT 30 40 50 0
Handheld Programmer Keystrokes $ STR $ STR N TMR SHFT B 1 SHFT A 0 ENT C 2 G 6 B 1 A 0 ENT
$ STR GX OUT
Accumulator Timer In the following example, a single input timer is used with a preset of 4.5 seconds. Comparative contacts are used to energized Y3, Y4, and Y5 at one second intervals Example Using respectively. The comparative contacts will turn off when the timer is reset. Comparative Contacts
DirectSOFT X1
TMRA K45 C10 C10 Y3 T20 X1 0 1 2 3
Timing Diagram
Seconds 4 5 6 7 8
TA20
K10
Y3 OUT
Y4 TA20 K20 Y4 OUT T20 TA20 K30 Y5 OUT Current Value 0 10 10 20 1/10 Seconds Handheld Programmer Keystrokes (cont) GX OUT B 2 C 0 SHFT D 3 SHFT T MLR ENT T MLR C 2 A 0 C 2 A 0 ENT C 2 2 A 0 1 A 0 B 1 A 0 ENT E 4 A 0 F 5 ENT ENT $ STR D 3 GX OUT A 0 E 4 SHFT ENT F 5 ENT ENT T MLR C 2 A 0 30 40 50 0 Y5
Handheld Programmer Keystrokes $ STR $ STR N TMR $ STR GX OUT $ STR SHFT B 1 SHFT A ENT C
535
Using Counters
Counters are used to count events . The counters available are up counters, up/down counters, and stage counters (used with RLL PLUS programming). The up counter has two inputs, a count input and a reset input. The maximum count value is 9999. The timing diagram below shows the relationship between the counter input, counter reset, associated discrete bit, current value, and counter preset.
X1 CNT CT1 K3
The up down counter has three inputs, a count up input, count down input and reset input. The maximum count value is 99999999. The timing diagram below shows the relationship between the counter input, counter reset, associated discrete bit, current value, and counter preset.
X1 X1 X2 X3 CT2 Current Value 1 2 1 Counts 2 3 0 X2 UDC CT2 K3
Up Down
X3
The stage counter has a count input and is reset by the RST instruction. This instruction is useful when programming using the RLL PLUS structured programming. The maximum count value is 9999. The timing diagram below shows the relationship between the counter input, associated discrete bit, current value, counter preset and reset instruction.
X1 CT2 Current Value RST CT2 1 2 Counts 3 4 0 X1
Up
SGCNT K3
CT2
536
Counter (CNT)
The Counter is a two input counter that increments when the count input logic transitions from off to on. When the counter reset input is on the counter resets to 0. When the current value equals the preset value, the counter status bit comes on and the counter continues to count up to a maximum count of 9999. The maximum value will be held until the counter is reset. Instruction Specifications Counter Reference (CTaaa): Specifies the counter number. Preset Value (Bbbb): Constant value (K) or a V memory location. Current Values: Counter current values are accessed by referencing the associated V or CT memory locations*. The V-memory location is the counter location + 1000. For example, the counter current value for CT3 resides in V memory location V1003.
Reset
Preset
The counter discrete status bit and the current value are not specified in the counter instruction.
Discrete Status Bit: The discrete status bit is accessed by referencing the associated CT memory location. It will be on if the value is equal to or greater than the preset value. For example the discrete status bit for counter 2 would be CT2. NOTE: Counter preset constants (K) may be changed by using a programming device, even when the CPU is in Run Mode. Therefore, a V-memory preset is required only if the ladder program must change the preset.
Operand Data Type A/B Counters V memory (preset only) Pointers (preset only) Constants (preset only) Counter discrete status bits Counter current values CT V P K aaa 0177
CT/V V/CT*
NOTE: * With the HPP, both the Counter discrete status bits and current value are accessed with the same data reference. DirectSOFT uses separate references, such as CT2 for discrete status bit for Counter CT2, and CTA2 for the current value of Counter CT2.
537
In the following example, when X1 makes an off to on transition, counter CT2 will increment by one. When the current value reaches the preset value of 3, the counter status bit CT2 will turn on and energize Y7. When the reset C10 turns on, the counter status bit will turn off and the current value will be 0. The current value for counter CT2 will be held in V memory location V1002.
Counting diagram
CNT K3 CT2 X1
DirectSOFT
X1
C10 C10
CT2
Y7 OUT
Handheld Programmer Keystrokes $ STR $ STR GY CNT B 1 SHFT C 2 ENT C 2 D 3 B 1 A 0 ENT ENT
Handheld Programmer Keystrokes (cont) $ STR GX OUT SHFT B 1 C 2 A 0 SHFT ENT T MLR C 2 ENT
Counter Example In the following example, when X1 makes an off to on transition, counter CT2 will Using Comparative increment by one. Comparative contacts are used to energize Y3, Y4, and Y5 at different counts. When the reset C10 turns on, the counter status bit will turn off and Contacts the counter current value will be 0, and the comparative contacts will turn off.
DirectSOFT
X1 CNT K3 C10 C10 CT2 X1
Counting diagram
CTA2
K1
Y3 OUT
Y3
CTA2
K3
Y5 OUT
Handheld Programmer Keystrokes $ STR $ STR GY CNT $ STR B 1 GX OUT B 1 SHFT C 2 SHFT ENT D 3 ENT C 2 ENT C 2 D 3 SHFT B 1 A 0 ENT T MLR C 2 ENT
Handheld Programmer Keystrokes (cont) $ STR C 2 GX OUT $ STR D 3 GX OUT SHFT ENT E 4 SHFT ENT F 5 ENT ENT C 2 SHFT T MLR C 2 C 2 SHFT T MLR C 2
538
The Stage Counter is a single input counter that increments when the input logic transitions from off to on. This counter differs from other counters since it will hold its current value until reset using the RST instruction. The Stage Counter is designed for use in RLL PLUS programs but can be used in relay ladder logic programs. When the current value equals the preset value, the counter status bit turns on and the counter continues to count up to a maximum count of 9999. The maximum value will be held until the counter is reset. Instruction Specifications Counter Reference (CTaaa): Specifies the counter number. Preset Value (Bbbb): Constant value (K) or a V memory location. Current Values: Counter current values are accessed by referencing the associated V or CT memory locations*. The V-memory location is the counter location + 1000. For example, the counter current value for CT3 resides in V memory location V1003. Discrete Status Bit: The discrete status bit is accessed by referencing the associated CT memory location. It will be on if the value is equal to or greater than the preset value. For example the discrete status bit for counter 2 would be CT2.
Operand Data Type A/B Counters V memory (preset only) Pointers (preset only) Constants (preset only) Counter discrete status bits Counter current values CT V P K aaa 0177 DL05 Range bbb 12007377 74007577 12007377 74007577 09999
The counter discrete status bit and the current value are not specified in the counter instruction.
CT/V V/CT*
NOTE: * With the HPP, both the Counter discrete status bits and current value are accessed with the same data reference. DirectSOFT uses separate references, such as CT2 for discrete status bit for Counter CT2, and CTA2 for the current value of Counter CT2.
539
In the following example, when X1 makes an off to on transition, stage counter CT7 will increment by one. When the current value reaches 3, the counter status bit CT7 will turn on and energize Y7. The counter status bit CT7 will remain on until the counter is reset using the RST instruction. When the counter is reset, the counter status bit will turn off and the counter current value will be 0. The current value for counter CT7 will be held in V memory location V1007.
Counting diagram
SGCNT K3 CT7 X1 Y10 Current Value RST CT7
DirectSOFT
X1
CT7
Y7 OUT
C5
CT7 RST
Handheld Programmer Keystrokes $ STR SHFT H 7 $ STR S RST B 1 SHFT D 3 SHFT ENT G 6 ENT C 2 SHFT T MLR H 7 ENT SHFT GY CNT
Handheld Programmer Keystrokes (cont) GX OUT $ STR S RST B 1 SHFT SHFT C 2 C 2 A 0 ENT F 5 SHFT ENT T MLR H 7 ENT
In the following example, when X1 makes an off to on transition, counter CT2 will increment by one. Comparative contacts are used to energize Y3, Y4, and Y5 at different counts. Although this is not shown in the example, when the counter is reset using the Reset instruction, the counter status bit will turn off and the current value will be 0. The current value for counter CT2 will be held in V memory location V1002.
Counting diagram
SGCNT CT2 K10 X1
CT2
K1
Y3 OUT Y3
CT2
K3
Y5 OUT
Handheld Programmer Keystrokes $ STR SHFT C 2 $ STR B 1 GX OUT S RST G 6 B 1 SHFT ENT D 3 ENT C 2 B 1 ENT SHFT A 0 GY CNT ENT SHFT T MLR C 2
Handheld Programmer Keystrokes (cont) $ STR C 2 GX OUT $ STR D 3 GX OUT SHFT ENT E 4 SHFT ENT F 5 ENT ENT C 2 SHFT T MLR C 2 C 2 SHFT T MLR C 2
540
This Up/Down Counter counts up on each off to on transition of the Up input and counts down on each off to on transition of the Down input. The counter is reset to 0 when the Reset input is on. The count range is 099999999. The count input not being used must be off in order for the active count input to function. Instruction Specification Counter Reference (CTaaa): Specifies the counter number. Preset Value (Bbbb): Constant value (K) or two consecutive V memory locations. Current Values: Current count is a double word value accessed by referencing the associated V or CT memory locations*. The V-memory location is the counter location + 1000. For example, the counter current value for CT5 resides in V memory location V1005 and V1006. Discrete Status Bit: The discrete status bit is accessed by referencing the associated CT memory location. Operating as a counter done bit it will be on if the value is equal to or greater than the preset value. For example the discrete status bit for counter 2 would be CT2.
Operand Data Type A/B Counters V memory (preset only) Pointers (preset only) Constants (preset only) Counter discrete status bits Counter current values CT V P K aaa 0176 DL05 Range bbb 12007377 74007577 12007377 74007577 099999999
Up
UDC
Down
Reset
Preset
Caution: The UDC uses two V memory locations for the 8 digit current value. This means that the UDC uses two consecutive counter locations. If UDC CT1 is used in the program, the next available counter is CT3.
The counter discrete status bit and the current value are not specified in the counter instruction.
CT/V V/CT*
NOTE: * With the HPP, both the Counter discrete status bits and current value are accessed with the same data reference. DirectSOFT uses separate references, such as CT2 for discrete status bit for Counter CT2, and CTA2 for the current value of Counter CT2.
541
In the following example if X2 and X3 are off ,when X1 toggles from off to on the counter will increment by one. If X1 and X3 are off the counter will decrement by one when X2 toggles from off to on. When the count value reaches the preset value of 3, the counter status bit will turn on. When the reset X3 turns on, the counter status bit will turn off and the current value will be 0.
Counting Diagram UDC K3 CT2 X1
X2 X2 X3 X3
CT2
Handheld Programmer Keystrokes $ STR $ STR $ STR SHFT U ISG D 3 D 3 C 2 B 1 ENT ENT ENT C 2 C 2
Handheld Programmer Keystrokes (cont) D 3 $ STR GX OUT ENT SHFT B 1 C 2 A 0 SHFT ENT T MLR C 2 ENT
In the following example, when X1 makes an off to on transition, counter CT2 will increment by one. Comparative contacts are used to energize Y3 and Y4 at different counts. When the reset (X3) turns on, the counter status bit will turn off, the current value will be 0, and the comparative contacts will turn off.
Counting Diagram
UDC V2000 CT2 X1
X2 X2 X3 X3
CTA2
K1
Y3 OUT
Y3
Handheld Programmer Keystrokes $ STR $ STR $ STR SHFT SHFT $ STR U ISG V AND C 2 SHFT C 2 D 3 A 0 D 3 C 2 B 1 ENT ENT ENT C 2 A 0 SHFT A 0 T MLR C 2 ENT C 2
D 3 SHFT ENT E 4
ENT
542
The Shift Register instruction shifts data through a predefined number of control relays. The control ranges in the shift register block must start at the beginning of an 8 bit boundary use 8-bit blocks. The Shift Register has three contacts. S Data determines the value (1 or 0) that will enter the register S Clock shifts the bits one position on each low to high transition S Reset resets the Shift Register to all zeros.
DATA
SR From A aaa
With each off to on transition of the clock input, the bits which make up the shift register block are shifted by one bit position and the status of the data input is placed into the starting bit position in the shift register. The direction of the shift depends on the entry in the From and To fields. From C0 to C17 would define a block of sixteen bits to be shifted from left to right. From C17 to C0 would define a block of sixteen bits, to be shifted from right to left. The maximum size of the shift register block depends on the number of available control relays. The minimum block size is 8 control relays.
Operand Data Type A/B Control Relay C aaa 0777 DL05 Range bbb 0777 Handheld Programmer Keystrokes $ Data Input SR $ X2 From Clock Input To Reset Input C17 C0 $ STR SHFT S RST B 1 STR D 3 SHFT H 7 STR C 2 B 1 ENT ENT ENT R ORN ENT SHFT A 0
DirectSOFT
X1
X3
0 0 0 0 0 1
0 0 1 0 0
- indicates on
- indicates off
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
543
X1
OUT V2010 Copy data from the lower 16 bits of the accumulator to V2010 8 9 3 5 V2010
Since the accumulator is 32 bits and V memory locations are 16 bits the Load Double and Out Double (or variations thereof) use two consecutive V-memory locations or 8 digit BCD constants to copy data either to the accumulator from a V-memory address or from a V-memory address to the accumulator. For example if you wanted to copy data from V2000 and V2001 to V2010 and V2011 the most efficient way to perform this function would be as follows:
X1 LDD V2000 Copy data from V2000 and V2001 to the accumulator Acc. 6 7 3 9 5 0 2 6 6 V2001 7 3 9 5 V2000 0 2 6
OUTD V2010 Copy data from the accumulator to V2010 and V2011 6 7 3 9 5 0 2 6
V2011
V2010
544
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
Instructions that manipulate data also use the accumulator. The result of the manipulated data resides in the accumulator. The data that was being manipulated is cleared from the accumulator. The following example loads the constant value 4935 into the accumulator, shifts the data right 4 bits, and outputs the result to V2010.
X1
Constant
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0
8 1
7 0
6 5 0 1
4 3 1 0
2 1
1 0
0 1
The upper 16 bits of the accumulator will be set to 0 S S S S Shifted out of accumulator
SHFR K4 Shift the data in the accumulator 4 bits (K4) to the right Acc.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
8 0
7 1
6 5 0 0
4 3 1 0
2 0
1 1
0 1
V2010
Some of the data manipulation instructions use 32 bits. They use two consecutive V memory locations or an 8 digit BCD constant to manipulate data in the accumulator. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is added with the value in V2006 and V2007 using the Add Double instruction. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
V2001 X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 6 ADDD V2006 Add the value in the accumulator with the value in V2006 and V2007 OUTD + 2 Acc. 8 7 0 7 3 0 3 9 0 9 5 4 9 0 0 0 2 4 7 6 6 2 (Accumulator) (V2006 and V2007) 6 7 3 9 5 V2000 0 2 6
V2011
V2010
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
545
The accumulator stack is used for instructions that require more than one parameter Using the Accumulator Stack to execute a function or for user defined functionality. The accumulator stack is used when more than one Load instruction is executed without the use of an Out instruction. The first load instruction in the scan places a value into the accumulator. Every Load instruction thereafter without the use of an Out instruction places a value into the accumulator and the value that was in the accumulator is placed onto the accumulator stack. The Out instruction nullifies the previous load instruction and does not place the value that was in the accumulator onto the accumulator stack when the next load instruction is executed. Every time a value is placed onto the accumulator stack the other values in the stack are pushed down one location. The accumulator is eight levels deep (eight 32 bit registers). If there is a value in the eighth location when a new value is placed onto the stack, the value in the eighth location is pushed off the stack and cannot be recovered.
X1
LD K3245 Load the value 3245 into the accumulator Constant Current Acc. value Acc. 0 0 0 0 3 2 4 5 Level 1 Previous Acc. value Acc. X X X X X X X X Level 2 Level 3 Level 4 Level 5 Level 6 LD K5151 Load the value 5151 into the accumulator, pushing the value 3245 onto the stack Constant Current Acc. value Acc. 0 0 0 0 5 1 5 1 Accumulator Stack 0 3 2 4 5 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 LD K6363 Load the value 6363 into the accumulator, pushing the value 5151 to the 1st stack location and the value 3245 to the 2nd stack location Constant Current Acc. value Acc. 0 0 0 0 6 3 6 3 Accumulator Stack 0 5 1 5 1 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 5 3 X X X X X X 1 2 X X X X X X 5 4 X X X X X X 1 5 X X X X X X Bucket 6 3 6 3 Level 7 Level 8 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 3 X X X X X X X 2 X X X X X X X 4 X X X X X X X 5 X X X X X X X 5 1 5 1 Level 7 Level 8 Accumulator Stack X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 3 2 4 5
Bucket
Bucket
The POP instruction rotates values upward through the stack into the accumulator. When a POP is executed the value which was in the accumulator is cleared and the value that was on top of the stack is in the accumulator. The values in the stack are shifted up one position in the stack.
546
X1
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
POP
Previous Acc. value Acc. X X X X X X X X Accumulator Stack 0 4 5 4 5 Level 1 Level 2 Level 3 Level 4 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 3 7 X X X X X X 7 9 X X X X X X 9 3 X X X X X X 2 0 X X X X X X
POP the 1st value on the stack into the accumulator and move stack values up one location
POP
Previous Acc. value Acc. 0 0 0 0 4 5 4 5 Accumulator Stack 0 3 7 9 2 Level 1 Level 2 Level 3 Level 4 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 7 X X X X X X X 9 X X X X X X X 3 X X X X X X X 0 X X X X X X X
POP the 1st value on the stack into the accumulator and move stack values up one location
Previous Acc. value POP Acc. 0 0 0 0 3 7 9 2 Accumulator Stack X 7 9 3 0 Level 1 Level 2 Level 3 Level 4 Level 5 OUT V2002 Copy data from the accumulator to V2002 V2002 7 9 3 0 Level 6 Level 7 Level 8 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Current Acc. value POP the 1st value on the stack into the accumulator and move stack values up one location Acc. X X X
Using Pointers
Many of the DL05 series instructions will allow V-memory pointers as a operand (commonly known as indirect addressing). Pointers allow instructions to obtain data from V-memory locations referenced by the pointer value. NOTE: DL05 V-memory addressing is in octal. However, the pointers reference a V-memory location with values viewed as HEX. Use the Load Address (LDA) instruction to move an address into the pointer location. This instruction performs the Octal to Hexadecimal conversion automatically.
In the following simple example we are using a pointer operand in a Load instruction. V-memory location 2000 is being used as the pointer location. V2000 contains the value 440 which the CPU views as the Hex equivalent of the Octal address V-memory location V2100. The CPU will copy the data from V2100 which in this example contains the value 2635 into the lower word of the accumulator.
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
547
X1
LD P2000 V1400 (P1400) contains the value 440 HEX. 440 HEX. = 2100 Octal which contains the value 2635. V2000 0 4 4 0
X X 2 X X X X X
X X 6 X X X X X S S
X X 3 X X X X X
X X 5 X X X X X
Accumulator
2 6 3 5
OUT V2200 Copy the data from the lower 16 bits of the accumulator to V2200. 2 X 6 X
V2200 V2201
3 X
5 X
The following example is identical to the one above with one exception. The LDA (Load Address) instruction automatically converts the Octal address to Hex.
X1 LDA O 2100 Load the lower 16 bits of the accumulator with Hexadecimal equivalent to Octal 2100 (440) 2 Unused accumulator bits are set to zero Acc. 0 0 0 0 0 4 4 0 1 0 0 2100 Octal is converted to Hexadecimal 440 and loaded into the accumulator
OUT V 2000
Copy the data from the lower 16 bits of the accumulator to V2000
V2000 S S V2076 V2077 LD P 2000 V2000 (P2000) contains the value 440 Hex. 440 Hex. = 2100 Octal which contains the value 2635 V2100 0 4 4 0 V2100 V2101 V2102 V2103 V2104 V2105 X X 2 X X X X X X X 6 X X X X X S S V2200 V2201 2 X 6 X 3 X 5 X X X 3 X X X X X X X 5 X X X X X 0 0
Accumulator
0 0 2 6 3 5
OUT V 2200
Copy the data from the lower 16 bits of the accumulator to V2200
548
Load (LD)
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
The Load instruction is a 16 bit instruction that loads the value (Aaaa), which is either a V memory location or a 4 digit constant, into the lower 16 bits of the accumulator. The upper 16 bits of the accumulator are set to 0.
Operand Data Type A V memory Pointer Constant V P K DL05 Range aaa All (See page 428) All V mem. (See page 428) 0FFFF
LD A aaa
Description on when the pointer is outside of the available range. on when the value loaded into the accumulator by any instruction is zero. on when the result in the accumulator is negative.
NOTE: Two consecutive Load instructions will place the value of the first load instruction onto the accumulator stack. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator and output to V2010.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT C 2 GX OUT L ANDST A 0 D 3 A 0 SHFT A 0 V AND ENT C 2 A 0 B 1 A 0 ENT B 1 X SET 8 8
V2000 9 3 5
V2010
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
549
The Load Double instruction is a 32 bit instruction that loads the value (Aaaa), which is either two consecutive V memory locations or an 8 digit constant value, into the accumulator.
LDD A aaa
DL05 Range aaa All (See page 428) All V mem. (See page 428) 0FFFFFFFF
Description on when the pointer is outside of the available range. on when the value loaded into the accumulator by any instruction is zero. on when the value loaded into the accumulator by any instruction is zero.
NOTE: Two consecutive Load instructions will place the value of the first load instruction onto the accumulator stack. In the following example, when X1 is on, the 32 bit value in V2000 and V2001 will be loaded into the accumulator and output to V2010 and V2011.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the 32 bit accumulator Acc. 6 7 3 9 5 0 2 6 V2001 6 7 3 9 5 V2000 0 2 6
OUTD V2010 Copy the value in the 32 bit accumulator to V2010 and V2011 Handheld Programmer Keystrokes $ STR SHFT C 2 GX OUT C 2 L ANDST A 0 SHFT A 0 D 3 B 1 A 0 ENT D 3 A 0 A 0 B 1 ENT D 3 ENT
V2011
V2010
550
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
The Load Formatted instruction loads 132 consecutive bits from discrete memory locations into the accumulator. The instruction requires a starting location (Aaaa) and the number of bits (Kbbb) to be loaded. Unused accumulator bit locations are set to zero.
Operand Data Type A Inputs Outputs Control Relays Stage Bits Timer Bits Counter Bits Special Relays Constant X Y C S T CT SP K aaa 0377 0377 0777 0377 0177 0177 0777 DL05 Range bbb 132
LDF K bbb
A aaa
Description on when the value loaded into the accumulator by any instruction is zero. on when the value loaded into the accumulator by any instruction is zero.
NOTE: Two consecutive Load instructions will place the value of the first load instruction onto the accumulator stack. In the following example, when C0 is on, the binary pattern of C10C16 (7 bits) will be loaded into the accumulator using the Load Formatted instruction. The lower 7 bits of the accumulator are output to Y0Y6 using the Out Formatted instruction.
DirectSOFT
C0 LDF K7 Load the status of 7 consecutive bits (C10C16) into the accumulator C10 Location C10 Constant K7 C16 C15 C14 C13 C12 C11 C10 OFF OFF OFF ON ON ON OFF
OUTF K7
Y0 Location Y0 Constant K7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
Copy the value from the specified number of bits in the accumulator to Y0 Y6
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT A 0 L ANDST C 2 SHFT F 5 H 7 ENT SHFT D 3 B 1 A 0 C 2 F 5 H 7 ENT A 0 ENT
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
551
The Load Address instruction is a 16 bit instruction. It converts any octal value or address to the HEX equivalent value and loads the HEX value into the accumulator. This instruction is useful when an address parameter is required since all addresses for the DL05 system are in octal.
Operand Data Type DL05 Range aaa Octal Address O All V mem. (See page 428)
LDA O aaa
Description on when the value loaded into the accumulator by any instruction is zero. on when the value loaded into the accumulator by any instruction is zero.
NOTE: Two consecutive Load instructions will place the value of the first load instruction onto the accumulator stack. In the following example when X1 is on, the octal number 40400 will be converted to a HEX 4100 and loaded into the accumulator using the Load Address instruction. The value in the lower 16 bits of the accumulator is copied to V2000 using the Out instruction.
DirectSOFT
X1 LDA O 40400 Load The HEX equivalent to the octal number into the lower 16 bits of the accumulator 4 0 Octal 4 0 0 Hexadecimal 4 1 0 0
OUT V2000 Copy the value in lower 16 bits of the accumulator to V2000 Handheld Programmer Keystrokes $ STR SHFT E 4 GX OUT L ANDST A 0 D 3 E 4 SHFT A 0 V AND C 2 B 1 ENT A 0 A 0 ENT
V2000
A 0
A 0
A 0
ENT
552
Out (OUT)
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
The Out instruction is a 16 bit instruction that copies the value in the lower 16 bits of the accumulator to a specified V memory location (Aaaa).
Operand Data Type A V memory Pointer Discrete Bit Flags SP53 V P DL05 Range aaa All (See page 428) All V mem. (See page 428) Description on when the pointer is outside of the available range.
OUT A aaa
In the following example, when X1 is on, the value in V2000 will be loaded into the lower 16 bits of the accumulator using the Load instruction. The value in the lower 16 bits of the accumulator are copied to V2010 using the Out instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 8 9 3 5 8 The unused accumulator bits are set to zero Acc. 0 0 0 0 8 9 3 5 V2000 9 3 5 Handheld Programmer Keystrokes $ STR SHFT C 2 GX OUT L ANDST A 0 D 3 A 0 SHFT A 0 V AND ENT C 2 A 0 B 1 A 0 ENT B 1 ENT
V2010
The Out Double instruction is a 32 bit instruction that copies the value in the accumulator to two consecutive V memory locations at a specified starting location (Aaaa).
Operand Data Type A V memory Pointer Discrete Bit Flags SP53 V P DL05 Range aaa All (See page 428) All V mem. (See page 428) Description on when the pointer is outside of the available range.
OUTD A aaa
In the following example, when X1 is on, the 32 bit value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is output to V2010 and V2011 using the Out Double instruction. Standard RLL Instructions
DirectSOFT
6 X1 LDD V2000 SHFT Load the value in V2000 and V2001 into the accumulator OUTD V2010 Copy the value in the accumulator to V2010 and V2011 6 7 3 9 5 0 2 6 Acc. 6 7 3 9 5 0 2 6 C 2 GX OUT C 2 V2001 7 3 9 5 V2000 0 2 6 Handheld Programmer Keystrokes $ STR L ANDST A 0 SHFT A 0 D 3 B 1 A 0 ENT D 3 A 0 A 0 B 1 ENT D 3 ENT
V2011
V2010
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
553
The Out Formatted instruction outputs 132 bits from the accumulator to the specified discrete memory locations. The instruction requires a starting location (Aaaa) for the destination and the number of bits (Kbbb) to be output.
Operand Data Type A Inputs Outputs Control Relays Constant X Y C K aaa 0377 0377 0777 DL05 Range bbb 132
In the following example, when C0 is on, the binary pattern of C10C16 (7 bits) will be loaded into the accumulator using the Load Formatted instruction. The lower 7 bits of the accumulator are output to Y0Y6 using the Out Formatted instruction.
DirectSOFT
C0 LDF K7 Load the status of 7 consecutive bits (C10C16) into the accumulator C10 Location C10 Constant K7 C16 C15 C14 C13 C12 C11 C10 OFF OFF OFF ON ON ON OFF
OUTF K7
Y0
Accumulator
Copy the value of the specified number of bits from the accumulator to Y20Y26 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT A 0 L ANDST C 2 SHFT F 5 H 7 ENT SHFT D 3 B 1 A 0 C 2 F 5 H 7 ENT A 0 ENT
Location Y0
Constant K7
Y26 Y25 Y24 Y23 Y22 Y21 Y20 OFF OFF OFF ON ON ON OFF
Pop (POP)
The Pop instruction moves the value from the first level of the accumulator stack (32 bits) to the accumulator and shifts each value in the stack up one level.
POP
Description on when the result of the instruction causes the value in the accumulator to be zero.
554
Standard RLL Instructions Accumulator / Stack Load and Output Data Instructions
In the example below, when C0 is on, the value 4545 that was on top of the stack is moved into the accumulator using the Pop instruction The value is output to V2000 using the Out instruction. The next Pop moves the value 3792 into the accumulator and outputs the value to V2001. The last Pop moves the value 7930 into the accumulator and outputs the value to V2002. Please note if the value in the stack were greater than 16 bits (4 digits) the Out Double instruction would be used and 2 V memory locations for each Out Double must be allocated.
Previous Acc. value POP Acc. X X X X X X X X Accumulator Stack 0 4 5 4 5 Level 1 Level 2 Level 3 OUT V2000 V2000 4 5 4 5 Level 4 Level 5 Level 6 Level 7 Level 8 POP Previous Acc. value Acc. 0 0 0 0 4 5 4 5 Accumulator Stack 0 3 7 9 2 Level 1 Level 2 OUT V2001 Level 3 Level 4 Level 5 V2001 3 7 9 2 Level 6 Level 7 POP Level 8 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 0 X X X X X X X 7 X X X X X X X 9 X X X X X X X 3 X X X X X X X 0 X X X X X X X 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 0 0 X X X X X X 3 7 X X X X X X 7 9 X X X X X X 9 3 X X X X X X 2 0 X X X X X X
DirectSOFT
C0
Current Acc. value Pop the 1st. value on the stack into the accumulator and move stack values up one location Acc. 0 0 0
Pop the 1st. value on the stack into the accumulator and move stack values up one location
Pop the 1st. value on the stack into the accumulator and move stack values up one location
Previous Acc. value Acc. 0 0 0 0 3 7 9 2 Accumulator Stack 0 7 9 3 0 Level 1 Level 2 Level 3 Level 4 Level 5 V2002 7 9 3 0 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Current Acc. value OUT V2002 Copy the value in the lower 16 bits of the accumulator to V2002 Acc. 0 0 0
Handheld Programmer Keystrokes $ STR SHFT GX OUT P CV SHFT SHFT SHFT P CV SHFT SHFT P CV SHFT SHFT C 2 O INST# V AND O INST# V AND O INST# V AND P CV C 2 P CV C 2 P CV C 2 A 0 ENT ENT A 0 ENT A 0 ENT A 0 A 0 C 2 ENT A 0 B 1 ENT A 0 A 0 ENT
555
AND A aaa
Description Will be on if the result in the accumulator is zero on when the value loaded into the accumulator by any instruction is zero.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in the accumulator is anded with the value in V2006 using the And instruction. The value in the lower 16 bits of the accumulator is output to V2010 using the Out instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator Acc. AND V2006 AND the value in the accumulator with the value in V2006 Acc. 6A38 AND (V2006) Acc. OUT V2010 Copy the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT V AND GX OUT L ANDST D 3 SHFT SHFT V AND V AND C 2 C 2 A 0 B 1 ENT C 2 A 0 B 1 A 0 A 0 A 0 A 0 G 6 A 0 ENT ENT ENT 2 8 3 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 1 1 1 1 1 1 1 1 1 0 0 0 1 0 0 0 0 0 0 0 0 The upper 16 bits of the accumulator will be set to 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 8 0 7 0 6 5 1 1 4 3 1 1 2 0 1 1 0 0 V2000 2 8 7 A
V2010
556
The And Double is a 32 bit instruction that logically ands the value in the accumulator with two consecutive V memory locations or an 8 digit (max.) constant value (Aaaa). The result resides in the accumulator. Discrete status flags indicate if the result of the And Double is zero or a negative number (the most significant bit is on).
Operand Data Type DL05 Range aaa V memory Pointer Constant V P K All (See page 428) All (See page 428) 0FFFFFFFF
ANDD K aaa
Description Will be on if the result in the accumulator is zero Will be on is the result in the accumulator is negative
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is anded with 36476A38 using the And double instruction. The value in the accumulator is output to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator Acc. ANDD K36476A38 AND the value in the accumulator with the constant value 36476A38 Acc. AND 36476A38 Acc. 0 0 0 1 0 0 0 1 0 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 0 0 0 0 1 1 0 1 1 0 0 1 0 0 1 0 0 1 1 0 1 1 1 0 1 0 1 0 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 1 1 1 1 1 1 1 1 1 0 0 0 1 0 0 0 0 0 5 V2001 4 7 E 2 V2000 8 7 A
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 1 0 1 0 1 0 0 0 1 1 1 1 1 1 0 0 0 1 0 1 0 0
8 0
7 0
6 5 1 1
4 3 1 1
2 0
1 1
0 0
OUTD V2010 Copy the value in the accumulator to V2010 and V2011 1 4 4 6 2 8 3 8
V2011
V2010
Handheld Programmer Keystrokes $ STR SHFT V AND GX OUT L ANDST SHFT SHFT D 3 D 3 D 3 B 1 ENT D 3 SHFT C 2 C 2 K JMP A 0 D 3 B 1 A 0 A 0 G 6 A 0 E 4 ENT A 0 ENT H 7 G 6 SHFT A 0 SHFT D 3 I 8 ENT
557
Or (OR)
The Or instruction is a 16 bit instruction that logically ors the value in the lower 16 bits of the accumulator with a specified V memory location (Aaaa). The result resides in the accumulator. The discrete status flag indicates if the result of the Or is zero.
Operand Data Type A V memory Pointer V P DL05 Range aaa All (See page 428) All (See page 428)
OR A aaa
Description Will be on if the result in the accumulator is zero on when the value loaded into the accumulator by any instruction is zero.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in the accumulator is ored with V2006 using the Or instruction. The value in the lower 16 bits of the accumulator are output to V2010 using the Out instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator Acc. OR V2006 Or the value in the accumulator with the value in V2006 Acc. 6A38 OR (V2006) Acc. OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT Q OR GX OUT L ANDST D 3 SHFT SHFT V AND V AND C 2 C 2 A 0 B 1 ENT 6 A 7 A 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 1 0 1 0 0 0 0 0 0 The upper 16 bits of the accumulator will be set to 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 8 0 7 0 6 5 1 1 4 3 1 1 2 0 1 1 0 0 V2000 2 8 7 A
V2010
C 2
A 0 A 0
A 0 A 0 B 1
A 0 G 6 A 0
558
Or Double (ORD)
The Or Double is a 32 bit instruction that ors the value in the accumulator with the value (Aaaa), which is either two consecutive V memory locations or an 8 digit (max.) constant value. The result resides in the accumulator. Discrete status flags indicate if the result of the Or Double is zero or a negative number (the most significant bit is on).
Operand Data Type DL05 Range aaa V memory Pointer Constant V P K All (See page 428) All (See page 428) 0FFFFFFFF
ORD K aaa
Description Will be on if the result in the accumulator is zero Will be on is the result in the accumulator is negative
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is ored with 36476A38 using the Or Double instruction. The value in the accumulator is output to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into accumulator 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Acc. ORD K36476A38 OR the value in the accumulator with the constant value 36476A38 OUTD V2010 7 6 7 F 6 A 7 A Acc. OR 36476A38 Acc. 0 0 0 1 0 0 1 0 1 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 1 0 0 0 0 0 0 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 1 1 0 1 0 1 0 1 0 0 0 0 1 1 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 1 0 1 0 0 0 0 1 0 1 0 1 0 0 0 1 1 1 1 1 1 0 0 0 1 0 1 0 0 8 0 7 0 6 5 1 1 4 3 1 1 2 0 1 1 0 0 V2001 5 4 7 E 2 V2000 8 7 A
Copy the value in the accumulator to V2010 and V2011 Handheld Programmer Keystrokes $ STR SHFT Q OR GX OUT L ANDST SHFT SHFT D 3 D 3 D 3 B 1 ENT D 3 SHFT C 2 C 2 K JMP A 0 D 3 B 1 A 0 A 0 G 6 A 0 E 4 ENT A 0 ENT H 7
V2011
V2010
G 6
SHFT
A 0
SHFT
D 3
I 8
ENT
559
Exclusive Or (XOR)
The Exclusive Or instruction is a 16 bit instruction that performs an exclusive or of the value in the lower 16 bits of the accumulator and a specified V memory location (Aaaa). The result resides in the in the accumulator. The discrete status flag indicates if the result of the XOR is zero.
Operand Data Type A V memory Pointer V P DL05 Range aaa All (See page 428) All (See page 428)
XOR A aaa
Description Will be on if the result in the accumulator is zero on when the value loaded into the accumulator by any instruction is zero.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in the accumulator is exclusive ored with V2006 using the Exclusive Or instruction. The value in the lower 16 bits of the accumulator are output to V2010 using the Out instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator Acc. XOR V2006 XOR the value in the accumulator with the value in V2006 Acc. 6A38 XOR (V2006) Acc. OUT V2010 Copy the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes 4 2 4 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 0 1 0 1 1 1 0 1 1 0 1 1 0 0 0 0 1 0 1 0 0 0 0 0 0 The upper 16 bits of the accumulator will be set to 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 8 0 7 0 6 5 1 1 4 3 1 1 2 0 1 1 0 0 V2000 2 8 7 A
V2010
X SET
B 1 SHFT
Q OR V AND C 2
560
The Exclusive OR Double is a 32 bit instruction that performs an exclusive or of the value in the accumulator and the value (Aaaa), which is either two consecutive V memory locations or an 8 digit (max.) constant. The result resides in the accumulator. Discrete status flags indicate if the result of the Exclusive Or Double is zero or a negative number (the most significant bit is on).
Operand Data Type A V memory Pointer Constant Discrete Bit Flags SP63 SP70 V P K DL05 Range aaa All (See page 428) All (See page 428) 0FFFFFFFF Description Will be on if the result in the accumulator is zero Will be on is the result in the accumulator is negative
XORD K aaa
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is exclusively ored with 36476A38 using the Exclusive Or Double instruction. The value in the accumulator is output to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator XORD K36476A38 XORD the value in the accumulator with the constant value 36476A38 OUTD V2010 Copy the value in the accumulator to V2010 and V2011 Acc. XORD 36476A38 Acc. 0 0 0 1 0 0 1 0 1 0 1 1 1 0 0 0 0 1 1 1 0 0 1 0 1 0 0 0 0 0 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 1 0 0 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 0 1 0 1 1 1 0 1 1 0 1 1 0 0 0 0 1 0 1 0 0 0 Acc. 5 V2001 4 7 E 2 V2000 8 7 A
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 1 0 1 0 1 0 0 0 1 1 1 1 1 1 0 0 0 1 0 1 0 0
8 0
7 0
6 5 1 1
4 3 1 1
2 0
1 1
0 0
Handheld Programmer Keystrokes $ STR SHFT SHFT D 3 GX OUT L ANDST X SET G 6 SHFT D 3 D 3 Q OR E 4 B 1 ENT D 3 SHFT H 7 C 2 D 3 G 6 SHFT A 0 C 2 A 0 SHFT A 0 B 1 A 0 K JMP SHFT A 0 D 3 ENT I 8 A 0 ENT
V2011
V2010
ENT
561
Compare (CMP)
The compare instruction is a 16 bit instruction that compares the value in the lower 16 bits of the accumulator with the value in a specified V memory location (Aaaa). The corresponding status flag will be turned on indicating the result of the comparison.
Operand Data Type A V memory Pointer Discrete Bit Flags SP60 SP61 SP62 V P DL05 Range aaa All (See page 428) All (See page 428) Description On when the value in the accumulator is less than the instruction value. On when the value in the accumulator is equal to the instruction value. On when the value in the accumulator is greater than the instruction value.
CMP A aaa
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example when X1 is on, the constant 4526 will be loaded into the lower 16 bits of the accumulator using the Load instruction. The value in the accumulator is compared with the value in V2000 using the Compare instruction. The corresponding discrete status flag will be turned on indicating the result of the comparison. In this example, if the value in the accumulator is less than the value specified in the Compare instruction, SP60 will turn on energizing C30.
DirectSOFT
X1 LD K4526 Load the constant value 4526 into the lower 16 bits of the accumulator The unused accumulator bits are set to zero Acc. 0 0 0 0 4 5 2 6 4 Constant 5 2 6
CMP V2000 Compare the value in the accumulator with the value in V2000 SP60 C30 8
Compared with 9 4 5
V2000
Handheld Programmer Keystrokes $ STR SHFT SHFT $ STR GX OUT L ANDST C 2 D 3 SHFT SHFT SHFT M ORST SP STRN C 2 B 1 ENT SHFT P CV G 6 D 3 A 0 A 0 K JMP E 4 C 2 ENT ENT A 0 F 5 A 0 C 2 A 0 G 6 ENT ENT
562
The Compare Double instruction is a 32bit instruction that compares the value in the accumulator with the value (Aaaa), which is either two consecutive V memory locations or an 8digit (max.) constant. The corresponding status flag will be turned on indicating the result of the comparison.
Operand Data Type A V memory Pointer Constant Discrete Bit Flags SP60 SP61 SP62 V P K DL05 Range aaa All (See page 428) All (See page 428) 0FFFFFFFF Description On when the value in the accumulator is less than the instruction value. On when the value in the accumulator is equal to the instruction value. On when the value in the accumulator is greater than the instruction value.
CMPD A aaa
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is compared with the value in V2010 and V2011 using the CMPD instruction. The corresponding discrete status flag will be turned on indicating the result of the comparison. In this example, if the value in the accumulator is less than the value specified in the Compare instruction, SP60 will turn on energizing C30.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator Acc. 4 5 2 6 7 2 9 9 V2001 4 5 2 6 7 V2000 2 9 9
CMPD V2010 Compare the value in the accumulator with the value in V2010 and V2011 SP60 C30 6 7 3
Compared with 9 5 0 2 6
V2011
V2010
Handheld Programmer Keystrokes $ STR SHFT SHFT $ STR GX OUT L ANDST C 2 D 3 SHFT SHFT SHFT B 1 ENT D 3 M ORST SP STRN C 2 P CV G 6 D 3 A 0 A 0 D 3 ENT ENT C 2 A 0 C 2 A 0 A 0 A 0 ENT B 1 A 0 ENT
563
Math Instructions
Add (ADD) Add is a 16 bit instruction that adds a BCD value in the accumulator with a BCD value in a V memory location (Aaaa). The result resides in the accumulator.
Operand Data Type A V memory Pointer V P DL05 Range aaa All (See page 428) All (See page 428)
ADD A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit addition instruction results in a carry. On when the 32 bit addition instruction results in a carry. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in the lower 16 bits of the accumulator are added to the value in V2006 using the Add instruction. The value in the accumulator is copied to V2010 using the Out instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator ADD V2006 Add the value in the lower 16 bits of the accumulator with the value in V2006 OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST A 0 D 3 D 3 SHFT D 3 V AND C 2 A 0 B 1 ENT C 2 C 2 B 1 A 0 A 0 A 0 A 0 A 0 A 0 ENT G 6 ENT ENT 7 4 3 5 The unused accumulator bits are set to zero 0 0 0 0 4 + Acc. 2 7 4 V2000 9 3 5
9 5 4
3 0 3
5 0 5
(Accumulator) (V2006)
V2010
564
Add Double is a 32 bit instruction that adds the BCD value in the accumulator with a BCD value (Aaaa), which is either two consecutive V memory locations or an 8digit (max.) BCD constant. The result resides in the accumulator.
Operand Data Type A V memory Pointer Constant V P K DL05 Range aaa All (See page 428) All (See page 428) 099999999
ADDD A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit addition instruction results in a carry. On when the 32 bit addition instruction results in a carry. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is added with the value in V2006 and V2007 using the Add Double instruction. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT X1
V2001 LDD V2000 Load the value in V2000 and V2001 into the accumulator 6 ADDD V2006 Add the value in the accumulator with the value in V2006 and V2007 OUTD V2010 8 7 3 9 9 0 7 2 + 2 Acc. 8 7 0 7 3 0 3 9 0 9 5 4 9 0 0 0 2 4 7 6 6 2 (Accumulator) (V2006 and V2007) 6 7 3 9 5 V2000 0 2 6
Copy the value in the accumulator to V2010 and V2011 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST A 0 SHFT D 3 D 3 D 3 D 3 B 1 ENT D 3 D 3 SHFT V AND C 2 C 2 C 2 A 0 A 0 A 0 A 0
V2011
V2010
A 0 A 0 B 1
565
Subtract (SUB)
Subtract is a 16 bit instruction that subtracts the BCD value (Aaaa) in a V memory location from the BCD value in the lower 16 bits of the accumulator. The result resides in the accumulator.
SUB A aaa
DL05 Range aaa All (See page 428) All (See page 428)
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit subtraction instruction results in a borrow. On when the 32 bit subtraction instruction results in a borrow. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in V2006 is subtracted from the value in the accumulator using the Subtract instruction. The value in the accumulator is copied to V2010 using the Out instruction.
DirectSOFT
X1 2 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator SUB V2006 Acc. Subtract the value in V2006 from the value in the lower 16 bits of the accumulator OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST D 3 U ISG SHFT B 1 V AND C 2 B 1 ENT C 2 A 0 SHFT A 0 A 0 V AND B 1 C 2 A 0 A 0 ENT A 0 ENT A 0 G 6 ENT 0 8 8 3 The unused accumulator bits are set to zero 0 0 0 0 y V2000 4 7 5
2 1 0
4 5 8
7 9 8
5 2 3
(Accumulator) (V2006)
V2010
566
Subtract Double is a 32 bit instruction that subtracts the BCD value (Aaaa), which is either two consecutive V memory locations or an 8-digit (max.) constant, from the BCD value in the accumulator. The result resides in the accumulator.
Operand Data Type A V memory Pointer Constant V P K DL05 Range aaa All (See page 428) All (See page 428) 099999999
SUBD A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit subtraction instruction results in a borrow. On when the 32 bit subtraction instruction results in a borrow. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in V2006 and V2007 is subtracted from the value in the accumulator. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 0 LDD V2000 Load the value in V2000 and V2001 into the accumulator SUBD V2006 The in V2006 and V2007 is subtracted from the value in the accumulator OUTD V2010 Copy the value in the accumulator to V2010 and V2011 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST SHFT D 3 SHFT D 3 U ISG C 2 B 1 ENT D 3 B 1 A 0 D 3 B 1 A 0 C 2 A 0 C 2 A 0 A 0 ENT A 0 ENT A 0 G 6 ENT 0 0 3 9 0 8 9 9 y ACC. 0 0 V2001 1 0 6 3 V2000 2 7 4
0 6 3
6 7 9
3 2 0
2 3 8
7 7 9
4 5 9
V2011
V2010
567
Multiply (MUL)
Multiply is a 16 bit instruction that multiplies the BCD value (Aaaa), which is either a V memory location or a 4digit (max.) constant, by the BCD value in the lower 16 bits of the accumulator The result can be up to 8 digits and resides in the accumulator.
Operand Data Type A V memory Pointer Constant V P K DL05 Range aaa All (See page 428) All (See page 428) 09999
MUL A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in V2006 is multiplied by the value in the accumulator. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator MUL V2006 The value in V2006 is multiplied by the value in the accumulator 0 OUTD V2010 Copy the value in the accumulator to V2010 and V2011 0 0 2 5 0 0 0 The unused accumulator bits are set to zero 0 Acc. 0 0 0 2 5 0 0 0 0 1 0 0 2 0 0 5 0 (Accumulator) (V2006) 1 V2000 0 0 0
V2010
V2010
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST M ORST SHFT D 3 U ISG D 3 L ANDST C 2 B 1 ENT C 2 C 2 A 0 B 1 A 0 A 0 A 0 A 0 A 0 A 0 ENT G 6 ENT ENT
568
Multiply Double is a 32 bit instruction that multiplies the 8-digit BCD value in the accumulator by the 8-digit BCD value in the two consecutive V-memory locations specified in the instruction. The lower 8 digits of the results reside in the accumulator. Upper digits of the result reside in the accumulator stack.
Operand Data Type A Vmemory Pointer Discrete Bit Flags SP63 SP70 SP75 V P DL05 Range aaa All (See p. 428) All (See page 428) Description
MULD A aaa
On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the constant Kbc614e hex will be loaded into the accumulator. When converted to BCD the number is 12345678. That numberis stored in V1400 and V1401. After loading the constant K2 into the accumulator, we multiply it times 12345678, which is 24691356.
DirectSOFT Display
X1 LDD Kbc614e Load the hex equivalent of 12345678 decimal into the accumulator. Convert the value to BCD format. It will occupy eight BCD digits (32 bits). Output the number to V1400 and V1401 using the OUTD instruction. Load the constant K2 into the accumulator. 2 4 6 9 1 3 5 6 Acc. 2 4 6 9 1 3 5 V1401 1 2 3 4 5 V1400 6 7 8 1 2 3 4 5 6 7 8 (Accumulator)
BCD
OUTD V1400
2 6
(Accumulator)
LD K2
MULD V1400
Multiply the accumulator contents (2) by the 8-digit number in V1400 and V1401. Move the result in the accumulator to V1402 and V1403 using the OUTD instruction. SHFT B L ANDST E 1 B E 1 SHFT 4 K JMP C 2 B 3 B E 1 4 A 0 1 C 2 4 D 3 ENT A 0 D 3 SHFT A 0 ENT E 4 A 0 ENT B 1 ENT
V1403
V1500
B 1 SHFT D 3 D 3 U ISG D 3
ENT G 6
SHFT C 2
K JMP D 3
SHFT ENT
L ANDST
A 0
569
Divide (DIV)
Divide is a 16 bit instruction that divides the BCD value in the accumulator by a BCD value (Aaaa), which is either a V memory location or a 4-digit (max.) constant. The first part of the quotient resides in the accumulator and the remainder resides in the first stack location.
Operand Data Type A V memory Pointer Constant Discrete Bit Flags SP53 SP63 SP70 SP75 V P K Description DL05 Range aaa All (See page 428) All (See page 428) 19999
DIV A aaa
On when the value of the operand is larger than the accumulator can work with. On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, the value in V2000 will be loaded into the accumulator using the Load instruction. The value in the accumulator will be divided by the value in V2006 using the Divide instruction. The value in the accumulator is copied to V2010 using the Out instruction.
DirectSOFT
X1 5 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator DIV V2006 The value in the accumulator is divided by the value in V2006 Acc. 1 The unused accumulator bits are set to zero 0 0 0 0 5
V2000 0 0 0
0 4 0
0 9 2
(Accumulator) (V2006) 0 0 0 0 0 0 0 2
OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST D 3 D 3 I 8 SHFT V AND V AND C 2 B 1 ENT C 2 C 2 A 0 B 1 A 0 A 0 A 0 A 0 A 0 A 0 ENT G 6 ENT
V2010
ENT
570
Divide Double is a 32 bit instruction that divides the BCD value in the accumulator by a BCD value (Aaaa), which must be obtained from two consecutive V memory locations. (You cannot use a constant as the parameter in the box.) The first part of the quotient resides in the accumulator and the remainder resides in the first stack location.
Operand Data Type A Vmemory Pointer V P DL05 Range aaa All (See p. 428) All (See p. 428)
DIVD A aaa
Description On when the value of the operand is larger than the accumulator can work with. On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. On when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the value in V1400 and V1401 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is divided by the value in V1420 and V1421 using the Divide Double instruction. The first part of the quotient resides in the accumulator an the remainder resides in the first stack location. The value in the accumulator is copied to V1500 and V1501 using the Out Double instruction.
DirectSOFT Display
X1 LDD V1400 Load the value in V1400 and V1401 into the accumulator The unused accumulator bits are set to zero 0 DIVD V1420 The value in the accumulator is divided by the value in V1420 and V1421
0 Acc. 0 1 0 0 5 0 0 0 0 3 0 0 0 0 0 0 0 5 0 0 0 0 (Accumulator) (V1421 and V1420) 0 0 0 0 0 0 0 0 0 V1401 1 5 0 0 V1400 0 0 0
OUTD V1500 0 0 0 3 0 0 0 0
Copy the value in the accumulator to V1500 and V1501 Handheld Programmer Keystrokes $ STR B 1 B 1 B 1 F 5 E 4 E 4 A 0 A 0 C 2 A 0 B 1 ENT A 0 SHFT ENT A 0 L ANDST SHFT ENT ENT D 3 D 3 GX OUT I 8 SHFT D 3
V1501
V1500
V AND D 3
571
Increment (INC)
The Increment instruction increments a BCD value in a specified V memory location by 1 each time the instruction is executed.
INC A aaa
Decrement (DEC)
The Decrement instruction decrements a BCD value in a specified V memory location by 1 each time the instruction is executed.
DEC A aaa
Description on when the result of the instruction causes the value in the accumulator to be zero. on when a BCD instruction is executed and a NONBCD number was encountered.
NOTE: Status flags are valid only until another instruction uses the same flag.
In the following increment example, when C5 is on the value in V1400 increases by one.
DirectSOFT Display
C5 8 INC V1400 Increment the value in V1400 by 1. 8 Handheld Programmer Keystrokes $ STR SHFT I 8 C 2 N TMR C 2 F 5 ENT B 1 E 4 A 0 A 0 V1400 9 3 6 V1400 9 3 5
In the following decrement example, when C5 is on the value in V1400 is decreased by one.
DirectSOFT Display
C5 DEC V1400 Decrement the value in V1400 by 1. V1400 Handheld Programmer Keystrokes $ STR SHFT D 3 E 4 C 2 C 2 F 5 ENT B 1 E 4 A 0 A 0 8 9 3 4 8 V1400 9 3 5
572
The Increment Binary instruction increments a binary value in a specified V memory location by 1 each time the instruction is executed.
INCB A aaa
DL05 Range aaa All (See page 428) All (See page 428) Description on when the result of the instruction causes the value in the accumulator to be zero.
In the following example when C5 is on, the binary value in V2000 is increased by 1.
DirectSOFT
C5 INCB V2000 Increment the binary value in the accumulator by1 4 4 V2000 A 3 C Handheld Programmer Keystrokes $ STR SHFT V2000 A 3 D I 8 SHFT N TMR C 2 C 2 B 1 F 5 ENT C 2 A 0 A 0 A 0 ENT
The Decrement Binary instruction decrements a binary value in a specified V memory location by 1 each time the instruction is executed.
DECB A aaa
DL05 Range aaa All (See page 428) All (See page 428) Description on when the result of the instruction causes the value in the accumulator to be zero.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example when C5 is on, the value in V2000 is decreased by 1. Standard RLL Instructions
DirectSOFT
C5 4 DECB V2000 Decrement the binary value in the accumulator by1 4 V2000 A 3 B V2000 A 3 C Handheld Programmer Keystrokes $ STR SHFT D 3 SHFT E 4 C 2 C 2 B 1 F 5 ENT C 2 A 0 A 0 A 0 ENT
573
Add Binary is a 16 bit instruction that adds the unsigned 2s complement binary value in the lower 16 bits of the accumulator with an unsigned 2s complement binary value (Aaaa), which is either a V memory location or a 16-bit constant. The result can be up to 32 bits (unsigned 2s complement) and resides in the accumulator.
Operand Data Type A Vmemory Pointer Constant V P K DL05 Range aaa All (See p. 428) All V mem (See p. 428) 0FFFF
ADDB A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit addition instruction results in a carry. On when the 32 bit addition instruction results in a carry. On anytime the value in the accumulator is negative. On when a signed addition or subtraction results in a incorrect sign bit.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the value in V1400 will be loaded into the accumulator using the Load instruction. The binary value in the accumulator will be added to the binary value in V1420 using the Add Binary instruction. The value in the accumulator is copied to V1500 and V1501 using the Out instruction.
DirectSOFT Display
X1 0 LD V1400 Load the value in V1400 into the lower 16 bits of the accumulator The unused accumulator bits are set to zero 0 0 0 0 0 + V1420 The binary value in the accumulator is added to the binary value in V1420 Acc. 1 C C 9 1 V1400 A 0 5
A 2
0 C
5 4
(Accumulator) (V1420)
ADDB
OUTD V1500 Copy the value in the lower 16 bits of the accumulator to V1500 and V1501
C C V1500
Handheld Programmer Keystrokes $ STR B 1 B 1 E 4 E 4 C 2 A 0 A 0 B 1 ENT A 0 SHFT ENT ENT L ANDST SHFT GX OUT D 3 A 0 SHFT D 3 D 3 D 3 B 1 B 1 F 5 A 0 A 0 ENT
574
Subtract Binary is a 16 bit instruction that subtracts the unsigned 2s complement binary value (Aaaa), which is either a V memory location or a 16-bit 2s complement binary value, from the binary value in the accumulator. The result resides in the accumulator.
SUBB A aaa
DL05 Range aaa All (See p. 428) All (See p. 428) 0FFFF
Description On when the result of the instruction causes the value in the accumulator to be zero. On when the 16 bit subtraction instruction results in a borrow. On when the 32 bit subtraction instruction results in a borrow. On anytime the value in the accumulator is negative.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the value in V1400 will be loaded into the accumulator using the Load instruction. The binary value in V1420 is subtracted from the binary value in the accumulator using the Subtract Binary instruction. The value in the accumulator is copied to V1500 using the Out instruction.
DirectSOFT Display
X1 1 LD V1400 Load the value in V1400 into the lower 16 bits of the accumulator The unused accumulator bits are set to zero 0 0 0 0 1 y V1420 The binary value in V1420 is subtracted from the value in the accumulator Acc. 0 6 1 9 0 V1400 0 2 4
0 A
2 0
4 B
(Accumulator) (V1420)
SUBB
OUT V1500 Copy the value in the lower 16 bits of the accumulator to V1500
V1500
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST SHFT D 3 SHFT D 3 U ISG B 1 B 1 F 5 B 1 ENT B 1 B 1 A 0 A 0 E 4 A 0 B 1 A 0 ENT E 4 ENT C 2 A 0 ENT
575
Multiply Binary is a 16 bit instruction that multiplies the unsigned 2s complement binary value (Aaaa), which is either a V memory location or a 16-bit unsigned 2s complement binary constant, by the16-bit binary value in the accumulator The result can be up to 32 bits and resides in the accumulator.
Operand Data Type A Vmemory Pointer Constant Discrete Bit Flags SP63 SP70 V P K DL05 Range aaa All (See p. 428) All (See p. 428) 1FFFF Description
MULB A aaa
On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the value in V1400 will be loaded into the accumulator using the Load instruction. The binary value in V1420 is multiplied by the binary value in the accumulator using the Multiply Binary instruction. The value in the accumulator is copied to V1500 using the Out instruction.
DirectSOFT Display
X1 LD V1400 Load the value in V1400 into the lower 16 bits of the accumulator The unused accumulator bits are set to zero 0 0 0 0 0 Acc. The binary value in V1420 is multiplied by the binary value in the accumulator 0 0 0 1 0 C 0 V1400 A 0 1
A 0 C
0 2 2
1 E E
(Accumulator) (V1420)
MULB V1420
OUTD V1500 Copy the value in the lower 16 bits of the accumulator to V1500 and V1501
V1501
V1500
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST M ORST SHFT D 3 U ISG D 3 L ANDST B 1 B 1 F 5 A 0 B 1 ENT
B 1
E 4
A 0 B 1
A 0 E 4 A 0
576
Divide Binary is a 16 bit instruction that divides the unsigned 2s complement binary value in the accumulator by a binary value (Aaaa), which is either a V memory location or a 16-bit unsigned 2s complement binary constant. The first part of the quotient resides in the accumulator and the remainder resides in the first stack location.
Operand Data Type A Vmemory Pointer Constant V P K DL05 Range aaa All (See p. 428) All (See p. 428) 0FFFF
DIVB A aaa
Description On when the value of the operand is larger than the accumulator can work with. On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
NOTE: Status flags are valid only until another instruction uses the same flag. In the following example, when X1 is on, the value in V1400 will be loaded into the accumulator using the Load instruction. The binary value in the accumulator is divided by the binary value in V1420 using the Divide Binary instruction. The value in the accumulator is copied to V1500 using the Out instruction.
DirectSOFT Display
X1 F LD V1400 Load the value in V1400 into the lower 16 bits of the accumulator The unused accumulator bits are set to zero 0 DIVB V1420 The binary value in the accumulator is divided by the binary value in V1420 Acc. 0
0 0 0 F 0
V1400 A 0 1
A 0 3
0 5 2
1 0 0
(Accumulator) (V1420) 0 0 0 0 0 0 0 0
OUT V1500 Copy the value in the lower 16 bits of the accumulator to V1500
V1500
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST D 3 SHFT D 3 D 3 I 8 U ISG B 1 B 1 F 5 A 0 B 1 ENT B 1 E 4 B 1 A 0 A 0 E 4 A 0 ENT C 2 ENT A 0 ENT
577
In the following example, when X1 is on, the value formed by discrete locations X10X17 is loaded into the accumulator using the Load Formatted instruction. The number of bits in the accumulator set to 1 is counted using the Sum instruction. The value in the accumulator is copied to V1500 using the Out instruction.
Discrete Bit Flags SP63 Description On when the result of the instruction causes the value in the accumulator to be zero.
DirectSOFT Display
X1 LDF K8 Load the value represented by discrete locations X10X17 into the accumulator Acc. X10 The unused accumulator bits are set to zero
X17 X16 X15 X14 X13 X12 X11 X10 ON ON OFF OFF ON OFF ON ON
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
8 0
7 1
6 5 1 0
4 3 0 1
2 0
1 1
0 1
SUM
Acc. 0
OUT V1500 Copy the value in the lower 16 bits of the accumulator to V1500
V1500
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST D 3 SHFT B 1 U ISF F 5 B 1 ENT F 5 M ORST A 0 B 1 ENT A 0 ENT A 0 I 8 ENT
Shift Left is a 32 bit instruction that shifts the bits in the accumulator a specified number (Aaaa) of places to the left. The vacant positions are filled with zeros and the bits shifted out of the accumulator are discarded.
SHFL A aaa
578
Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The bit pattern in the accumulator is shifted 2 bits to the left using the Shift Left instruction. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 SHFL K2 The bit pattern in the accumulator is shifted 2 bit positions to the left Acc. 0 1 1 0 0 1 1 1 0 0 0 0 0 1 0 1 0 0 1 1 0 0 0 8 1 7 0 6 5 0 0 4 3 0 0 2 0 1 0 0 1 6 V2001 7 0 5 3 V2000 1 0 1
S S
S S
OUTD V2010 Copy the value in the accumulator to V2010 and V2011 Acc. 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 1 0 0 0 1 0 1 1 0 0 0 0 0 0 1 0 0 1 0 0 1 1 0 0 0 1 0 8 0 7 0 6 5 0 0 4 3 0 0 2 1 1 0 0 0
9 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST SHFT D 3 SHFT D 3 H 7 C 2 B 1 ENT D 3 F 5 C 2 L ANDST A 0 B 1 A 0 C 2 A 0 A 0 A 0 ENT ENT ENT
V2011
V2010
579
Shift Right is a 32 bit instruction that shifts the bits in the accumulator a specified number (Aaaa) of places to the right. The vacant positions are filled with zeros and the bits shifted out of the accumulator are lost.
Operand Data Type A V memory Constant V K DL05 Range aaa All (See page 428) 132
SHFR A aaa
Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The bit pattern in the accumulator is shifted 2 bits to the right using the Shift Right instruction. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 SHFR K2 The bit pattern in the accumulator is shifted 2 bit positions to the right Acc. 0 1 1 0 0 1 1 1 0 0 0 0 0 1 0 1 0 0 1 1 0 0 0 8 1 7 0 6 5 0 0 4 3 0 0 2 0 1 0 0 1 Constant 6 V2001 7 0 5 3 V2000 1 0 1
S S
S S
OUTD V2010 Copy the value in the accumulator to V2010 and V2011 Acc. 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 1 0 1 1 0 0 0 1 0 1 0 1 0 0 0 0 0 0 1 0 1 0 0 1 1 0 8 0 7 0 6 5 1 0 4 3 0 0 2 0 1 0 0 0
V2011 Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST S RST SHFT D 3 SHFT D 3 H 7 C 2 B 1 ENT
V2010
D 3 F 5
C 2 R ORN A 0
A 0
A 0 C 2
A 0 ENT ENT
ENT
B 1
A 0
580
Encode (ENCO)
The Encode instruction encodes the bit position in the accumulator having a value of 1, and returns the appropriate binary representation. If the most significant bit is set to 1 (Bit 31), the Encode instruction would place the value HEX 1F (decimal 31) in the accumulator. If the value to be encoded is 0000 or 0001, the instruction will place a zero in the accumulator. If the value to be encoded has more than one bit position set to a 1, the least significant 1 will be encoded and SP53 will be set on.
Discrete Bit Flags SP53 Description
ENCO
On when the value of the operand is larger than the accumulator can work with.
NOTE: The status flags are only valid until another instruction that uses the same flags is executed. In the following example, when X1 is on, The value in V2000 is loaded into the accumulator using the Load instruction. The bit position set to a 1 in the accumulator is encoded to the corresponding 5 bit binary value using the Encode instruction. The value in the lower 16 bits of the accumulator is copied to V2010 using the Out instruction.
DirectSOFT
X1 1 LD V2000 Load the value in V2000 into the lower 16 bits of the accumulator V2000 0 0 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Acc. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
8 0
7 0
6 5 0 0
4 3 0 0
2 0
1 0
0 0
Bit postion 12 is converted to binary ENCO 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Encode the bit position set to 1 in the accumulator to a 5 bit binary value Acc. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 0 7 0 6 5 0 0 4 3 0 1 2 1 1 0 0 0
V2010
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST E 4 D 3 N TMR SHFT C 2 V AND B 1 ENT C 2 O INST# C 2 A 0 ENT A 0 B 1 A 0 ENT A 0 A 0 ENT
581
Decode (DECO)
The Decode instruction decodes a 5 bit binary value of 031 (01F HEX) in the accumulator by setting the appropriate bit position to a 1. If the accumulator contains the value F (HEX), bit 15 will be set in the accumulator. If the value to be decoded is greater than 31, the number is divided by 32 until the value is less than 32 and then the value is decoded.
DECO
In the following example when X1 is on, the value formed by discrete locations X10X14 is loaded into the accumulator using the Load Formatted instruction. The five bit binary pattern in the accumulator is decoded by setting the corresponding bit position to a 1 using the Decode instruction.
DirectSOFT
X1 LDF K5 Load the value in represented by discrete locations X10X14 into the accumulator Acc. X10 X14 X13 X12 X11 X10 OFF ON OFF ON ON
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
8 0
7 0
6 5 0 0
4 3 0 1
2 0
1 1
0 1
DECO 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Decode the five bit binary pattern in the accumulator and set the corresponding bit position to a 1 Handheld Programmer Keystrokes $ STR SHFT SHFT L ANDST D 3 D 3 E 4 C 2 B 1 ENT F 5 O INST# B 1 ENT A 0 F 5 ENT Acc. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 8 0 7 0 6 5 0 0
582
BIN
In the following example, when X1 is on, the value in V2000 and V2001 is loaded into the accumulator using the Load Double instruction. The BCD value in the accumulator is converted to the binary (HEX) equivalent using the BIN instruction. The binary value in the accumulator is copied to V2010 and V2011 using the Out Double instruction. (The handheld programmer will display the binary value in V2010 and V2011 as a HEX value.)
Discrete Bit Flags SP63 SP70 SP75 Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. on when a BCD instruction is executed and a NONBCD number was encountered.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 8 Acc. 0 4 0 2 0 1 0 8 0 4 0 2 0 1 0 8 0 4 0 2 0 1 0 8 0 0
V2001 0 0 2 8
V2000 5 2 9
4 0
2 1
1 0
8 1
4 0
2 0
1 0
8 0
4 1
2 0
1 1
8 0
4 0
2 1
1 0
8 1
4 0
2 0
1 1
BCD Value
28529 = 16384 + 8192 + 2048 + 1024 + 512 + 256 + 64 + 32 + 16 + 1 Binary Equivalent Value 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Convert the BCD value in the accumulator to the binary equivalent value Acc. 0 2 1 4 7 4 4 8 3 6 4 8 0 1 0 7 3 7 4 1 8 2 4 0 5 3 6 8 7 0 9 1 2 0 2 6 8 4 3 5 4 5 6 0 1 3 4 2 1 7 7 2 8 0 6 7 1 0 8 8 6 4 0 3 3 5 5 4 4 3 2 0 1 6 7 7 7 2 1 6 0 8 3 8 8 6 0 8 0 4 1 9 4 3 0 4 0 2 0 9 7 1 5 2 0 1 0 4 8 5 7 6 0 5 2 4 2 8 8 0 2 6 2 1 4 4 0 1 3 1 0 7 2 0 6 5 5 3 6 0 3 2 7 6 8 1 1 6 3 8 4 1 8 1 9 2 0 4 0 9 6 1 2 0 4 8 1 1 0 2 4 1 5 1 2 8 1 2 5 6 7 0 6 5 1 1 3 2 4 3 1 0 2 0 4 1 0 2 0 1 1
BIN
1 6 2 4 8
1 8 6
OUTD V2010 Copy the binary value in the accumulator to V2010 and V2011
Handheld Programmer Keystrokes 0 $ STR SHFT SHFT GX OUT L ANDST B 1 SHFT D 3 D 3 I 8 B 1 ENT D 3 N TMR ENT C 2 A 0 B 1 A 0 ENT C 2 A 0 A 0 A 0 ENT 0 0 0 6 F 7 1 V2011 V2010
583
The Binary Coded Decimal instruction converts a binary value in the accumulator to the equivalent BCD value. The result resides in the accumulator.
BCD
In the following example, when X1 is on, the binary (HEX) value in V2000 and V2001 is loaded into the accumulator using the Load Double instruction. The binary value in the accumulator is converted to the BCD equivalent value using the BCD instruction. The BCD value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
Discrete Bit Flags SP63 SP70 Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative. V2001 LDD V2000 Load the value in V2000 and V2001 into the accumulator 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Acc. 0 2 1 4 7 4 4 8 3 6 4 8 0 1 0 7 3 7 4 1 8 2 4 0 5 3 6 8 7 0 9 1 2 0 2 6 8 4 3 5 4 5 6 0 1 3 4 2 1 7 7 2 8 0 6 7 1 0 8 8 6 4 0 3 3 5 5 4 4 3 2 0 1 6 7 7 7 2 1 6 0 8 3 8 8 6 0 8 0 4 1 9 4 3 0 4 0 2 0 9 7 1 5 2 0 1 0 4 8 5 7 6 0 5 2 4 2 8 8 0 2 6 2 1 4 4 0 1 3 1 0 7 2 0 6 5 5 3 6 0 3 2 7 6 8 1 1 6 3 8 4 1 8 1 9 2 0 4 0 9 6 1 2 0 4 8 1 1 0 2 4 1 5 1 2 8 1 2 5 6 7 0 6 5 1 1 3 2 4 3 1 0 2 0 4 1 0 2 0 1 1 Binary Value 0 0 0 0 6 V2000 F 7 1
DirectSOFT
X1
1 6 2 4 8
1 8 6
BCD
16384 + 8192 + 2048 + 1024 + 512 + 256 + 64 + 32 + 16 + 1 = 28529 BCD Equivalent Value 8 Acc. 0 4 0 2 0 1 0 8 0 4 0 2 0 1 0 8 0 4 0 2 0 1 0 8 0 4 0 2 1 1 0 8 1 4 0 2 0 1 0 8 0 4 1 2 0 1 1 8 0 4 0 2 1 1 0 8 1 4 0 2 0 1 1
Convert the binary value in the accumulator to the BCD equivalent value
OUTD V2010 Copy the BCD value in the accumulator to V2010 and V2011 0 0 0 2 8 5 2 9 The BCD value copied to V2010 and V2011
V2011
V2010
584
Invert (INV)
The Invert instruction inverts or takes the ones complement of the 32 bit value in the accumulator. The result resides in the accumulator.
INV
In the following example, when X1 is on, the value in V2000 and V2001 will be loaded into the accumulator using the Load Double instruction. The value in the accumulator is inverted using the Invert instruction. The value in the accumulator is copied to V2010 and V2011 using the Out Double instruction.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Acc. 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 1 8 0 7 0 6 5 1 0 4 3 1 0 2 0 1 0 0 0 0 V2001 4 0 5 0 V2000 2 5 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 0 1 1 1 1 1 1 0
8 1
7 1
6 5 0 1
4 3 0 1
2 1
1 1
0 1
OUTD V2010 Copy the value in the accumulator to V2010 and V2011
V2011
V2010
Handheld Programmer Keystrokes $ STR SHFT SHFT GX OUT L ANDST I 8 SHFT D 3 N TMR D 3 B 1 ENT D 3 V AND ENT C 2 A 0 B 1 A 0 ENT C 2 A 0 A 0 A 0 ENT
585
The ASCII TO HEX instruction converts a ATH table of ASCII values to a specified table of V aaa HEX values. ASCII values are two digits and their HEX equivalents are one digit. This means an ASCII table of four V memory locations would only require two V memory locations for the equivalent HEX table. The function parameters are loaded into the accumulator stack and the accumulator by two additional instructions. Listed below are the steps necessary to program an ASCII to HEX table function. The example on the following page shows a program for the ASCII to HEX table function. Step 1: Load the number of V memory locations for the ASCII table into the first level of the accumulator stack. Step 2: Load the starting V memory location for the ASCII table into the accumulator. This parameter must be a HEX value. Step 3: Specify the starting V memory location (Vaaa) for the HEX table in the ATH instruction. Helpful Hint: For parameters that require HEX values when referencing memory locations, the LDA instruction can be used to convert an octal address to the HEX equivalent and load the value into the accumulator.
Vmemory
Description On when the value of the operand is larger than the accumulator can work with.
In the example on the following page, when X1 is ON the constant (K4) is loaded into the accumulator using the Load instruction and will be placed in the first level of the accumulator stack when the next Load instruction is executed. The starting location for the ASCII table (V1400) is loaded into the accumulator using the Load Address instruction. The starting location for the HEX table (V1600) is specified in the ASCII to HEX instruction. The table below lists valid ASCII values for ATH conversion.
ASCII Values Valid for ATH Conversion
ASCII Value 30 31 32 33 34 35 36 37 Hex Value 0 1 2 3 4 5 6 7 ASCII Value 38 39 41 42 43 44 45 46 Hex Value 8
9 A B C D E F
586
X1
DirectSOFT Display
ASCII TABLE LD K4 Load the constant value into the lower 16 bits of the accumulator. This value defines the number of V memory location in the ASCII table Convert octal 1400 to HEX 300 and load the value into the accumulator V1401 ATH V1600 V1600 is the starting location for the HEX table
Hexadecimal Equivalents
V1400
33 34 1234 31 32
V1600
LDA O 1400
V1402
37 38 5678
V1601
Handheld Programmer Keystrokes $ STR SHFT SHFT SHFT L ANDST L ANDST A 0 D 3 D 3 T MLR H 7 A 0 B 1 B 1 ENT SHFT K JMP B 1 G 6 E 4 E 4 A 0 ENT A 0 A 0 A 0 ENT ENT V1403
35 36
The HEX to ASCII instruction converts a table of HEX values to a specified table of ASCII values. HEX values are one digit and their ASCII equivalents are two digits.
HTA V aaa
This means a HEX table of two V memory locations would require four V memory locations for the equivalent ASCII table. The function parameters are loaded into the accumulator stack and the accumulator by two additional instructions. Listed below are the steps necessary to program a HEX to ASCII table function. The example on the following page shows a program for the HEX to ASCII table function. Step 1: Load the number of V memory locations in the HEX table into the first level of the accumulator stack. Step 2: Load the starting V memory location for the HEX table into the accumulator. This parameter must be a HEX value. Step 3: Specify the starting V memory location (Vaaa) for the ASCII table in the HTA instruction. Standard RLL Instructions Helpful Hint: For parameters that require HEX values when referencing memory locations, the LDA instruction can be used to convert an octal address to the HEX equivalent and load the value into the accumulator.
587
All (See p. 428) Description On when the value of the operand is larger than the accumulator can work with.
In the following example, when X1 is ON the constant (K2) is loaded into the accumulator using the Load instruction. The starting location for the HEX table (V1500) is loaded into the accumulator using the Load Address instruction. The starting location for the ASCII table (V1400) is specified in the HEX to ASCII instruction.
DirectSOFT Display
X1 LD K2 Load the constant value into the lower 16 bits of the accumulator. This value defines the number of V locations in the HEX table. V1500 LDA O 1500 Convert octal 1500 to HEX 340 and load the value into the accumulator Hexadecimal Equivalents ASCII TABLE
33 34 1234 31 32
V1400
V1401
HTA V1400 V1400 is the starting location for the ASCII table. The conversion is executed by this instruction. Handheld Programmer Keystrokes $ STR SHFT SHFT SHFT L ANDST L ANDST H 7 D 3 D 3 T MLR A 0 A 0 B 1 B 1 ENT SHFT K JMP B 1 E 4 E 4 F 5 A 0 ENT A 0 A 0 A 0 ENT ENT V1501
37 38 5678 35 36
V1402
V1403
The table below lists valid ASCII values for HTA conversion.
ASCII Values Valid for HTA Conversion
Hex Value 0 1 2 3 4 5 6 7 ASCII Value 30 31 32 33 34 35 36 37 Hex Value 8 9 A B C D E F ASCII Value 38
39 41 42 43 44 45 46
588
The Gray code instruction converts a 16 bit gray code value to a BCD value. The BCD conversion requires 10 bits of the accumulator. The upper 22 bits are set to 0. This instruction is designed for use with devices (typically encoders) that use the grey code numbering scheme. The Gray Code instruction will directly convert a gray code number to a BCD number for devices having a resolution of 512 or 1024 counts per revolution. If a device having a resolution of 360 counts per revolution is to be used you must subtract a BCD value of 76 from the converted value to obtain the proper result. For a device having a resolution of 720 counts per revolution you must subtract a BCD value of 152.
GRAY
In the following example, when X1 is ON the binary value represented by X10X27 is loaded into the accumulator using the Load Formatted instruction. The gray code value in the accumulator is converted to BCD using the Gray Code instruction. The value in the lower 16 bits of the accumulator is copied to V2010.
Discrete Bit Flags SP63 SP70 Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
DirectSOFT
X1 LDF X10 Load the value represented by X10X27 into the lower 16 bits of the accumulator Acc. GRAY K16
S S
S S
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
8 0
7 0
6 5 0 0
4 3 0 0
2 1
1 0
0 1
Convert the 16 bit grey code value in the accumulator to a BCD value Acc. OUT V2010 Copy the value in the lower 16 bits of the accumulator to V2010 Handheld Programmer Keystrokes $ B STR SHFT SHFT GX OUT L ANDST G 6 D 3 R ORN SHFT A 0 V AND 1 ENT F 5 Y MLS C 2 B 1 ENT A 0 B 1 A A 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
8 0
7 0
6 5 0 0
4 3 0 0
2 1
1 1
0 0
Gray Code 0000000000 0000000001 0000000011 0000000010 B 1 G 6 ENT 0000000110 0000000111 0000000101 0000000100 0 ENT S S S 1000000001 1000000000
BCD 0000 0001 0002 0003 0004 0005 0006 0007 S S S 1022 1023 0 0 0 6
V2010
589
The Shuffle Digits instruction shuffles a maximum of 8 digits rearranging them in a specified order. This function requires parameters to be loaded into the first level of the accumulator stack and the accumulator with two additional instructions. Listed below are the steps necessary to use the shuffle digit function. The example on the following page shows a program for the Shuffle Digits function.
SFLDGT
Step 1: Load the value (digits) to be shuffled into the first level of the accumulator stack. Step 2: Load the order that the digits will be shuffled to into the accumulator. Note: If the number used to specify the order contains a 0 or 9F, the corresponding position will be set to 0. See example on the next page. Note:If the number used to specify the order contains duplicate numbers, the most significant duplicate number is valid. The result resides in the accumulator. See example on the next page. Step 3: Insert the SFLDGT instruction.
Discrete Bit Flags SP63 SP70 Description On when the result of the instruction causes the value in the accumulator to be zero. On anytime the value in the accumulator is negative.
There are a maximum of 8 digits that can be shuffled. The bit positions in the first level of the accumulator stack defines the digits to be shuffled. They correspond to the bit positions in the accumulator that define the order the digits will be shuffled. The digits are shuffled and the result resides in the accumulator.
Bit Positions
8 B
7 C
6 E
5 F
4 0
3 D
2 A
1 9
Result (accumulator)
590
In the following example when X1 is on, The value in the first level of the accumulator stack will be reorganized in the order specified by the value in the accumulator. Example A shows how the shuffle digits works when 0 or 9 F is not used when specifying the order the digits are to be shuffled. Also, there are no duplicate numbers in the specified order. Example B shows how the shuffle digits works when a 0 or 9F is used when specifying the order the digits are to be shuffled. Notice when the Shuffle Digits instruction is executed, the bit positions in the first stack location that had a corresponding 0 or 9F in the accumulator (order specified) are set to 0. Example C shows how the shuffle digits works when duplicate numbers are used specifying the order the digits are to be shuffled. Notice when the Shuffle Digits instruction is executed, the most significant duplicate number in the order specified is used in the result.
DirectSOFT
X1 LDD V2000 Load the value in V2000 and V2001 into the accumulator 9 V2001 A B C D
A
V2000 E F 0 0 V2001 F E D
B
V2000 C B A 9 9 V2001 A B C
C
V2000 D E F 0
4 D
3 E
2 F
1 0 Acc.
8 7 6 5 0 F E D
4 C
3 B
2 A
1 9
8 Acc. 9
7 A
6 B
5 C
4 D
3 E
2 F
1 0 Acc.
LDD V2006 Load the value in V2006 and V2007 into the accumulator 1
V2006 7 3 6 5 4 0
V2007 0 4 3 0
V2006 0 2 1 4
V2007 3 2 1 4
V2006 3 2 1
Specified order
8 1
7 2
6 8
5 7
4 3
3 6
2 5
1 4 Acc.
8 0
7 0
6 4
5 3
4 0
3 0
2 2
1 1 Acc.
8 4
7 3
6 2
5 1
4 4
3 3
2 2
1 1 Acc.
SFLDGT
8 B
7 C
6 E
5 F
4 0
3 D
2 A
1 9 Acc.
8 7 6 5 0 0 0 0
4 E
3 D
2 A
1 9
8 Acc. 0
7 0
6 0
5 0
4 9
3 A
2 B
1 C Acc.
Shuffle the digits in the first level of the accumulator stack based on the pattern in the accumulator. The result is in the accumulator. OUTD V2010 V2011 Copy the value in the accumulator to V2010 and V2011 V2010 V2011 V2010 V2011 V2010 B C E F 0 D A 9 0 0 0 0 E D A 9 0 0 0 0 9 A B C
Handheld Programmer Keystrokes $ STR B 1 L ANDST L ANDST S RST SHFT D 3 D 3 SHFT D 3 F 5 D 3 L ANDST C 2 D 3 A 0 B 1 ENT D 3 C 2 G 6 C 2 A 0 A 0 A 0 T MLR A 0 A 0 G 6 ENT ENT A 0 ENT ENT
591
Table Instructions
Move (MOV) The Move instruction moves the values from a V memory table to another V memory table the same length. The function parameters are loaded into the first level of the accumulator stack and the accumulator by two additional instructions. Listed below are the steps necessary to program the Move function. S S S
MOV V aaa
Step 1: Load the number of V memory locations to be moved into the first level of the accumulator stack. This parameter is a HEX value (K40 max, 100 octal). Step 2: Load the starting V memory location for the locations to be moved into the accumulator. This parameter is a HEX value. Step 3: Insert the MOVE instruction which specifies starting V memory location (Vaaa) for the destination table.
Helpful Hint: For parameters that require HEX values when referencing memory locations, the LDA instruction can be used to convert an octal address to the HEX equivalent and load the value into the accumulator.
Operand Data Type DL05 Range aaa V memory Pointer Discrete Bit Flags SP53 V P All (See page 428) All (See page 428) Description On when the value of the operand is larger than the accumulator can work with.
In the following example, when X1 is on, the constant value (K6) is loaded into the accumulator using the Load instruction. This value specifies the length of the table and is placed in the first stack location after the Load Address instruction is executed. The octal address 2000 (V2000), the starting location for the source table is loaded into the accumulator. The destination table location (V2030) is specified in the Move instruction.
DirectSOFT
X1 LD K6 LDA O 2000 MOV V2030 Handheld Programmer Keystrokes $ STR SHFT SHFT SHFT L ANDST L ANDST M ORST D 3 D 3 O INST# A 0 V AND C 2 B 1 ENT SHFT K JMP C 2 A 0 G 6 A 0 D 3 ENT A 0 A 0 A 0 ENT ENT Load the constant value 6 (HEX) into the lower 16 bits of the accumulator Convert octal 2000 to HEX 400 and load the value into the accumulator Copy the specified table locations to a table beginning at location V2030 0 0 9 3 8 1 X X 1 5 9 0 9 0 X X S S S S 2 0 9 7 8 1 X X 3 V2000 0 V2001 9 V2002 4 V2003 9 V2004 0 V2005 X V2006 X V2007 X X 0 0 9 3 8 1 X X X X 1 5 9 0 9 0 X X S S S S X X 2 0 9 7 8 1 X X X V2026 X V2027 3 V2030 0 V2031 9 V2032 4 V2033
592
The Move Memory Cartridge and the Load Label instructions are used to copy data from program ladder memory to V memory. The Load Label instruction is used with the MOVMC instruction when copying data from program ladder memory to V memory. To copy data from the program ladder memory to V memory, the function parameters are loaded into the first two levels of the accumulator stack and the accumulator by two additional instructions. Listed below are the steps necessary to program the Move Memory Cartridge and Load Label functions. S S S S
MOVMC V aaa
LDLBL K aaa
Step 1: Load the number of words to be copied into the second level of the accumulator stack. Step 2: Load the offset for the data label area in ladder memory and the beginning of the V memory block into the first level of the stack. Step 3: Load the source data label (LDLBL Kaaa) into the accumulator when copying data from ladder memory to V memory. This is the source location of the value. Step 4: Insert the MOVMC instruction which specifies destination in V-memory (Vaaa). This is the copy destination.
DL05 Range A aaa All (See page 428)
V memory
593
In the example to the right, data is copied from a Data Label Area to V memory. When X1 is on, the constant value (K4) is loaded into the accumulator using the Load instruction. This value specifies the length of the table and is placed in the second stack location after the next Load and Load Label (LDLBL) instructions are executed. The constant value (K0) is loaded into the accumulator, specifying the offset for the source and destination data. It is placed in the first stack location after the LDLBL instruction is executed. The source address where data is being copied from is loaded into the accumulator using the LDLBL instruction. The MOVMC instruction specifies the destination starting location and executes the copying of data from the Data Label Area to V memory.
Data Label Area Programmed After the END Instruction
DirectSOFT X1
S S 1 2 5 1 8 X S S 3 3 5 4 X 4 2 1 5 X V2000
LD K4 Load the value 4 into the accumulator specifying the number of locations to be copied. LD K0
DLBL K1
N K N K N K N K C O N 1 4 6 8 2 5 1 8 3 3 5 4 4 4 2 6 1 8 5 X C O N C O N C O N
V2001
V2002
V2003
Load the value 0 into the accumulator specifying the offset for source and destination locations LDLBL
V2004
K1 Load the value 1 into the accumulator specifying the Data Label Area K1 as the starting address of the data to be copied. MOVMC
Handheld Programmer Keystrokes $ STR SHFT SHFT SHFT SHFT L ANDST L ANDST L ANDST M ORST D 3 D 3 D 3 O INST# L ANDST V AND B 1 ENT SHFT SHFT B 1 M ORST K JMP K JMP L ANDST C 2 E 4 A 0 ENT ENT B 1 C 2 ENT A 0 A 0 A 0 ENT V2000 V2000 is the destination starting address for the data to be copied.
594
DirectSOFT
End (END)
The End instruction marks the termination point of the normal program scan. An End instruction is required at the end of the main program body. If the End instruction is omitted an error will occur and the CPU will not enter the Run Mode. Data labels, subroutines and interrupt routines are placed after the End instruction. The End instruction is not conditional; therefore, no input contact is allowed.
DirectSOFT
Handheld Programmer Keystrokes SHFT END E 4 N TMR D 3 ENT
END
Stop (STOP)
The Stop instruction changes the operational mode of the CPU from Run to Program (Stop) mode. This instruction is typically used to stop PLC operation in an error condition.
STOP
In the following example, when C0 turns on, the CPU will stop operation and switch to the program mode. Standard RLL Instructions
DirectSOFT
C0 STOP SHFT Handheld Programmer Keystrokes $ STR S RST SHFT SHFT C 2 T MLR A 0 O INST# ENT P CV ENT
Description On when the DL05 goes into the TERM_PRG mode. On when the DL05 goes into the PRG mode.
595
The Reset Watch Dog Timer instruction resets the CPU scan timer. The default setting for the watch dog timer is 200ms. Scan times very seldom exceed 200ms, RSTWT but it is possible. For/next loops, subroutines, interrupt routines, and table instructions can be programmed such that the scan becomes longer than 200ms. When instructions are used in a manner that could exceed the watch dog timer setting, this instruction can be used to reset the timer. A software timeout error (E003) will occur and the CPU will enter the program mode if the scan time exceeds the watch dog timer setting. Placement of the RSTWT instruction in the program is very important. The instruction has to be executed before the scan time exceeds the watch dog timers setting. If the scan time is consistently longer than the watch dog timers setting, the timeout value may be permanently increased from the default value of 200ms by AUX 55 on the HPP or the appropriate auxiliary function in your programming package. This eliminates the need for the RSTWT instruction. In the following example the CPU scan timer will be reset to 0 when the RSTWT instruction is executed. See the For/Next instruction for a detailed example.
DirectSOFT
Handheld Programmer Keystrokes SHFT RSTWT R ORN S RST T MLR W ANDN T MLR ENT
596
A aaa FOR
NEXT
597
In the following example, when X1 is on, the application program inside the For / Next loop will be executed three times. If X1 is off the program inside the loop will not be executed. The immediate instructions may or may not be necessary depending on your application. Also, The RSTWT instruction is not necessary if the For / Next loop does not extend the scan time larger the Watch Dog Timer setting. For more information on the Watch Dog Timer, refer to the RSTWT instruction.
DirectSOFT X1
K3 FOR 1 2 3
RSTWT
X20
Y5 OUT
NEXT
Handheld Programmer Keystrokes $ STR SHFT SHFT $ STR GX OUT SHFT N TMR F 5 R ORN SHFT B 1 O INST# S RST I 8 F 5 E 4 ENT X SET T MLR ENT ENT R ORN T MLR W ANDN C 2 D 3 T MLR A 0 ENT ENT ENT
598
The Goto Subroutine instruction allows a section of ladder logic to be placed outside the main body of the program execute only when needed. There can be a maximum of 64 GTS instructions and 64 SBR instructions used in a program. The GTS instructions can be nested up to 8 levels. An error E412 will occur if the maximum limits are exceeded. Typically this will be used in an application where a block of program logic may be slow to execute and is not required to execute every scan. The subroutine label and all associated logic is placed after the End statement in the program. When the subroutine is called from the main program, the CPU will execute the subroutine (SBR) with the same constant number (K) as the GTS instruction which called the subroutine. By placing code in a subroutine it is only scanned and executed when needed since it resides after the End instruction. Code which is not scanned does not impact the overall scan time of the program.
Operand Data Type DL05 Range aaa Constant K 1FFFF
K aaa GTS
SBR
K aaa
When a Subroutine Return is executed in the subroutine the CPU will return to the point in the main body of the program from which it was called. The Subroutine Return is used as termination of the subroutine which must be the last instruction in the subroutine and is a stand alone instruction (no input contact on the rung). The Subroutine Return Conditional instruction is a optional instruction used with a input contact to implement a conditional return from the subroutine. The Subroutine Return (RT) is still required for termination of the Subroutine.
RT
RTC
599
In the following example, when X1 is on, Subroutine K3 will be called. The CPU will jump to the Subroutine Label K3 and the ladder logic in the subroutine will be executed. If X35 is on the CPU will return to the main program at the RTC instruction. If X35 is not on Y0Y17 will be reset to off and then the CPU will return to the main body of the program.
DirectSOFT Display
X1 C0 LD K10 S S S END SBR K3 K3 GTS
X20
X21
RT
Handheld Programmer Keystrokes $ STR SHFT S S SHFT SHFT $ STR GX OUT $ STR GX OUT $ STR SHFT SP STRN S RST SHFT E 4 S RST SHFT SHFT SHFT SHFT SHFT R ORN SHFT SHFT R ORN N TMR SHFT I 8 I 8 I 8 I 8 I 8 T MLR I 8 I 8 T MLR ENT A 0 C 2 D 3 ENT D 3 F 5 ENT B 1 H 7 ENT B 1 F 5 C 2 A 0 F 5 D 3 B 1 ENT R ORN C 2 A 0 ENT B 1 ENT ENT ENT D 3 ENT ENT G 6 B 1 T MLR ENT S RST D 3 ENT
5100
In the following example, when X1 is on, Subroutine K3 will be called. The CPU will jump to the Subroutine Label K3 and the ladder logic in the subroutine will be executed. The CPU will return to the main body of the program after the RT instruction is executed.
DirectSOFT
X1 K3 GTS
S S S END
SBR
K3
X20
Y5 OUT
X21
Y10 OUT
RT
Handheld Programmer Keystrokes $ STR SHFT S S SHFT SHFT $ STR GX OUT $ STR GX OUT SHFT E 4 S RST SHFT N TMR SHFT I 8 F 5 I 8 B 1 R ORN T MLR A 0 ENT ENT C 2 ENT B 1 ENT D 3 B 1 ENT R ORN C 2 A 0 D 3 ENT ENT G 6 B 1 T MLR ENT S RST D 3 ENT
SHFT
5101
The Master Line Set instruction allows the program to control sections of ladder logic by forming a new power rail controlled by the main left power rail. The main left rail is always master line 0. When a MLS K1 instruction is used, a new power rail is created at level 1. Master Line Sets and Master Line Resets can be used to nest power rails up to seven levels deep.
Operand Data Type DL05 Range aaa Constant K 17
K aaa MLS
The Master Line Reset instruction marks the end of control for the corresponding MLS instruction. The MLR reference is one less than the corresponding MLS.
K aaa MLR
Constant
07
The Master Line Set (MLS) and Master Line Reset (MLR) instructions allow you to quickly enable (or disable) sections of the RLL program. This provides program control flexibility. The following example shows how the MLS and MLR instructions operate by creating a sub power rail for control logic.
X0 MLS K1 When contact X0 is on, logic under the first MLS will be executed.
X1
Y7 OUT
X2
MLS K2
When contact X2 and X0 is on, logic under the second MLS will be executed. X3
MLR K0
MLR K1
The MLR instructions note the end of the Master Control area. (They will be entered in adjacent addresses.)
X10
5102
MLS/MLR Example In the following MLS/MLR example logic between the first MLS K1 (A) and MLR K0 (B) will function only if input X0 is on. The logic between the MLS K2 (C) and MLR K1 (D) will function only if input X10 and X0 is on. The last rung is not controlled by either of the MLS coils.
DirectSOFT
X0 K1 MLS X1 C0 OUT X2 C1 OUT X3 Y0 OUT X10 K2 MLS X5 Y1 OUT X4 Y2 OUT K1 MLR X5 C2 OUT X6 Y3 OUT K0 MLR X7 Y4 OUT B D C A Handheld Programmer Keystrokes $ STR Y MLS $ STR GX OUT $ STR GX OUT $ STR GX OUT $ STR Y MLS $ STR GX OUT $ STR GX OUT T MLR $ STR GX OUT $ STR GX OUT T MLR $ STR GX OUT E 4 D 3 A 0 H 7 C 2 B 1 F 5 SHFT G 6 B 1 E 4 C 2 F 5 A 0 B 1 B 1 B 1 SHFT C 2 SHFT D 3 A 0 ENT ENT ENT C 2 ENT C 2 ENT ENT A 0 ENT ENT ENT ENT ENT ENT ENT C 2 ENT ENT ENT ENT C 2 ENT C 2 ENT ENT B 1 ENT A 0 ENT
5103
Interrupt Instructions
Interrupt (INT) The Interrupt instruction allows a section of ladder logic to be placed below the main body of the program and executed only when needed. High-Speed I/O Modes 10, 20, and 40 can generate an interrupt. With Mode 40, you may select an external interrupt (input X0), or a time-based interrupt (5999 mS).
INT
INT
Typically, interrupts are used in an application when a fast response to an input is needed or a program section must execute faster than the normal CPU scan. The interrupt label and all associated logic must be placed after the End statement in the program. When an interrupt occurs, the CPU will complete execution of the current instruction it is processing in ladder logic, then execute the interrupt routine. After interrupt routine execution, the ladder program resumes from the point at which it was interrupted. See Chapter 3, the section on Mode 40 (Interrupt) Operation for more details on interrupt configuration. In the DL05, only one hardware interrupt is available.
Operand Data Type Constant O DL05 Range 0, 1
An Interrupt Return is normally executed as the last instruction in the interrupt routine. It returns the CPU to the point in the main program from which it was called. The Interrupt Return is a stand-alone instruction (no input contact on the rung). The Interrupt Return Conditional instruction is a optional instruction used with an input contact to implement a condtional return from the interrupt routine. The Interrupt Return is required to terminate the interrupt routine.
IRT
IRTC
The Enable Interrupt instruction is placed in the main ladder program (before the End instruction), enabling the interrupt. The interrupt remains enabled until the program executes a Disable Interrupt instruction.
ENI
5104
A Disable Interrupt instruction in the main body of the application program (before the End instruction) will disable the interupt (either extenal or timed). The interrupt remains disabled until the program executes an Enable Interrupt instruction.
DISI
In the following example, we do some initialization on the first scan, using the first-scan contact SP0. The interrupt feature is the HSIO Mode 40. Then we configure X0 as the external interrupt by writing to its configuration register, V7634. See Chapter 3, Mode 40 Operation for more details. During program execution, when X2 is on the interrupt is enabled. When X2 is off the interrupt will be disabled. When an interrupt signal (X0) occurs the CPU will jump to the interrupt label INT O 0. The application ladder logic in the interrupt routine will be performed. The CPU will return to the main body of the program after the IRT instruction is executed.
DirectSOFT LD
K40 OUT V7633 LD K4 OUT V7634 Handheld Programmer Keystrokes Load the constant value (K40) into the lower 16 bits of the accumulator Copy the value in the lower 16 bits of the accumulator to V7633 Load the constant value (K4) into the lower 16 bits of the accumulator Copy the value in the lower 16 bits of the accumulator to V7634 $ STR SHFT GX OUT SHFT GX OUT $ STR ENI SHFT SP STRN SHFT D 3 E 4 L ANDST L ANDST SHFT D 3 SHFT D 3 SHFT C 2 N TMR C 2 I 8 I 8 ENT S RST I 8 ENT V AND ENT ENT V AND SP STRN A 0 SHFT H 7 SHFT H 7 ENT K JMP G 6 K JMP G 6 E 4 D 3 E 4 D 3 D 3 ENT E 4 ENT A 0 ENT ENT
SP0
X2
X2 DISI
S S S END
S S SHFT SHFT E 4 I 8 SHFT SHFT SHFT SHFT I 8 N TMR N TMR I 8 I 8 I 8 I 8 R ORN T MLR H 7 ENT D 3 F 5 D 3 T MLR B 1 ENT A 0 ENT ENT ENT ENT ENT
INT
X3
IRT
5105
In the following example, we do some initialization on the first scan, using the first-scan contact SP0. The interrupt feature is the HSIO Mode 40. Then we configure the HSIO timer as a 10 mS interrupt by writing K104 to the configuration register for X0 (V7634). See Chapter 3, Mode 40 Operation for more details. When X4 turns on, the interrupt will be enabled. When X4 turns off, the interrupt will be disabled. Every 10 mS the CPU will jump to the interrupt label INT O 0. The application ladder logic in the interrupt routine will be performed. If X3 is not on Y0Y7 will be reset to off and then the CPU will return to the main body of the program.
Handheld Programmer Keystrokes LD K40 Load the constant value (K40) into the lower 16 bits of the accumulator $ STR SHFT OUT V7633 Copy the value in the lower 16 bits of the accumulator to V7633 GX OUT SHFT LD K104 Load the constant value (K10) into the lower 16 bits of the accumulator GX OUT $ STR OUT V7634 Copy the value in the lower 16 bits of the accumulator to V7634 SHFT SP STRN SHFT S S DISI SHFT SHFT END $ E 4 I 8 SHFT SHFT SHFT SHFT I 8 N TMR N TMR I 8 I 8 I 8 I 8 R ORN T MLR A 0 ENT D 3 F 5 D 3 T MLR C 2 ENT A 0 ENT ENT ENT H 7 ENT ENT D 3 E 4 L ANDST L ANDST D 3 SHFT D 3 SHFT E 4 N TMR E 4 I 8 I 8 ENT S RST I 8 ENT V AND ENT ENT V AND B 1 ENT SHFT H 7 SHFT H 7 K JMP G 6 K JMP G 6 B 1 D 3 E 4 E 4 D 3 A 0 D 3 A 0 ENT ENT E 4 ENT ENT
DirectSOFT
X1
X4 ENI X4
S S
INT
O0
STR X SET
X2
Y5 SETI
X3
Y0 RSTI
IRT
Independent Timed Interrupt O1 is also available as an interrupt. This interrupt is independent of the HSIO features. Interrupt O1 uses an internal timer that is configured in V memory Interrupt location V7647. The interrupt period can be adjusted from 5 to 9999 mS. Once the interrupt period is set and the interrupt is enabled in the program, the CPU will continuously call the interrupt routine based on the time setting in V7647. Input Configuration Register V7647 Function High-Speed Timed Interrupt Hex Code Required xxxx (xxxx = timer setting) 5 - 9999 mS (BCD)
5106
Message Instructions
Fault (FAULT) The Fault instruction is used to display a message on the handheld programmer or in the DirectSOFT status bar. The message has a maximum of 23 characters and can be either V memory data, numerical constant data or ASCII text.
FAULT A aaa
To display the value in a V memory location, specify the V memory location in the instruction. To display the data in ACON (ASCII constant) or NCON (Numerical constant) instructions, specify the constant (K) value for the corresponding data label area.
Operand Data Type A V memory Constant V K DL05 Range aaa All (See page 428) 1FFFF
Fault Example
In the following example when X1 is on, the message SW 146 will display on the handheld programmer. The NCONs use the HEX ASCII equivalent of the text to be displayed. (The HEX ASCII for a blank is 20, a 1 is 31, 4 is 34 ...)
Handheld Programmer Keystrokes
SW 146
DirectSOFT S S X1
FAULT K1
B 1 A 0
S S
DLBL K1 ACON A SW
N TMR L ANDST C 2 C 2 C 2
ENT L ANDST N TMR N TMR N TMR B 1 S RST C 2 D 3 E 4 ENT W ANDN A 0 D 3 ENT D 3 G 6 B 1 ENT ENT
SHFT SHFT
NCON K 2031
SHFT SHFT
NCON K 3436
5107
The Data Label instruction marks the beginning of an ASCII / numeric data area. DLBLs are programmed after the End statement. A maximum of 64 DLBL instructions can be used in a program. Multiple NCONs and ACONs can be used in a DLBL area.
Operand Data Type DL05 Range aaa Constant K 1FFFF
DLBL
K aaa
The ASCII Constant instruction is used with the DLBL instruction to store ASCII text for use with other instructions. Two ASCII characters can be stored in an ACON instruction. If only one character is stored in a ACON a leading space will be inserted.
Operand Data Type DL05 Range aaa ASCII A 09 AZ
ACON A aaa
The Numerical Constant instruction is used with the DLBL instruction to store the HEX ASCII equivalent of numerical data for use with other instructions. Two digits can be stored in an NCON instruction.
NCON K aaa
Constant
0FFFF
5108
In the following example, an ACON and two NCON instructions are used within a DLBL instruction to build a text message. See the FAULT instruction for information on displaying messages. The DV-1000 Manual also has information on displaying messages.
DirectSOFT
S S S END
DLBL K1
ACON A SW
NCON K 2031
NCON K 3436
Handheld Programmer Keystrokes S S SHFT SHFT SHFT SHFT SHFT E 4 D 3 A 0 N TMR N TMR C 2 C 2 N TMR L ANDST C 2 D 3 B 1 O INST# O INST# O INST# ENT L ANDST N TMR N TMR N TMR B 1 S RST C 2 D 3 E 4 ENT W ANDN A 0 D 3 ENT D 3 G 6 B 1 ENT ENT
5109
The Print Message instruction prints the embedded text or text/data variable message to the specified communications port (Port 2 on the DL05 CPU), which must have the communications port configured.
A aaa
You may recall from the CPU specifications in Chapter 3 that the DL05s ports are capable of several protocols. Port 1 cannot be configured for the non-sequence portocol. To configure port 2 using the Handheld Programmer, use AUX 56 and follow the prompts, making the same choices as indicated below on this page. To configure a port in DirectSOFT, choose the PLC menu, then Setup, then Setup Secondary Comm Port. S Port: From the port number list box at the top, choose Port 2. S Protocol: Click the check box to the left of Non-sequence, and then youll see the dialog box shown below.
Setup Communication Ports Port: Protocol: Port 2 K-sequence DirectNET MODBUS Non-sequence Remote I/O V2000 7 9600 1 Close
Help
Parity: Odd
S S S
Memory Address: Choose a V-memory address for DirectSOFT to use to store the port setup information. You will need to reserve 9 words in V-memory for this purpose. Select Always use for printing if it applies. Baud Rate: Choose the baud rate that matches your printer. Stop Bits, Parity: Choose number of stop bits and parity setting to match your printer. Then click the button indicated to send the Port 2 configuration to the CPU, and click Close. Then see Chapter 3 for port wiring information, in order to connect your printer to the DL05.
5110
Port 2 on the DL05 has standard RS232 levels, and should work with most printer serial input connections. Text element this is used for printing character strings. The character strings are defined as the character (more than 0) ranged by the double quotation marks. Two hex numbers preceded by the dollar sign means an 8-bit ASCII character code. Also, two characters preceded by the dollar sign is interpreted according to the following table:
# 1 2 3 4 5 6 7 Character code $$ $ $L or $l $N or $n $P or $p $R or $r $T or $t Description Dollar sign ($) Double quotation () Line feed (LF) Carriage return line feed (CRLF) Form feed Carriage return (CR) Tab
The following examples show various syntax conventions and the length of the output to the printer. Example: Length 0 without character A Length 1 with character A Length 1 with blank $ Length 1 with double quotation mark $R$L Length 2 with one CR and one LF $0D$0A Length 2 with one CR and one LF $$ Length 1 with one $ mark In printing an ordinary line of text, you will need to include double quotation marks before and after the text string. Error code 499 will occur in the CPU when the print instruction contains invalid text or no quotations. It is important to test your PRINT instruction data during the application development. The following example prints the message to port 2. We use a PD contact, which causes the message instruction to be active for just one scan. Note the $N at the end of the message, which produces a carriage return / line feed on the printer. This prepares the printer to print the next line, starting from the left margin.
X1 PRINT K2 Hello, this is a PLC message.$N Print the message to Port 2 when X1 makes an off-to-on transition.
5111
V-memory element this is used for printing V-memory contents in the integer format or real format. Use V-memory number or V-memory number with : and data type. The data types are shown in the table below. The Character code must be capital letters. NOTE: There must be a space entered before and after the V-memory address to separate it from the text string. Failure to do this will result in an error code 499.
# 1 2 3 4 Character code none :B :D :DB 4 digit BCD 32-bit binary (decimal number) 8 digit BCD Description 16-bit binary (decimal number)
Print binary data in V2000 for decimal number Print BCD data in V2000 Print binary number in V2000 and V2001 for decimal number Print BCD data in V2000 and V2001
Example: The following example prints a message containing text and a variable. The reactor temperature labels the data, which is at V2000. You can use the : B qualifier after the V2000 if the data is in BCD format, for example. The final string adds the units of degrees to the line of text, and the $N adds a carriage return / line feed.
X1 PRINT K2 Reactor temperature = V2000 deg. $N Message will read: Reactor temperature = 0156 deg Print the message to Port 2 when X1 makes an off-to-on transition. represents a space
V-memory text element this is used for printing text stored in V-memory. Use the % followed by the number of characters after V-memory number for representing the text. If you assign 0 as the number of characters, the print function will read the character count from the first location. Then it will start at the next V-memory location and read that number of ASCII codes for the text from memory. Example: V2000 % 16 16 characters in V2000 to V2007 are printed. V2000 % 0 The characters in V2001 to Vxxxx (determined by the number in V2000) will be printed.
5112
Bit element this is used for printing the state of the designated bit in V-memory or a relay bit. The bit element can be assigned by the designating point (.) and bit number preceded by the V-memory number or relay number. The output type is described as shown in the table below.
# 1 2 3 Data format none : BOOL : ONOFF Description Print 1 for an ON state, and 0 for an OFF state Print TRUE for an ON state, and FALSE for an OFF state Print ON for an ON state, and OFF for an OFF state
Prints the status of bit 15 in V2000, in 1/0 format Prints the status of C100 in 1/0 format Prints the status of C100 in TRUE/FALSE format Prints the status of C00 in ON/OFF format Prints the status of bit 15 in V2000 in TRUE/FALSE format
The maximum numbers of characters you can print is 128. The number of characters for each element is listed in the table below:
Element type Text, 1 character 16 bit binary 32 bit binary 4 digit BCD 8 digit BCD Floating point (real number) Floating point (real with exponent) V-memory/text Bit (1/0 format) Bit (TRUE/FALSE format) Bit (ON/OFF format) Maximum Characters 1 6 11 4 8 12 12 2 1 5 3
The handheld programmers mnemonic is PRINT, followed by the DEF field. Special relay flags SP116 and SP117 indicate the status of the DL05 CPU ports (busy, or communications error). See the appendix on special relays for a description. NOTE: You must use the appropriate special relay in conjunction with the PRINT command to ensure the ladder program does not try to PRINT to a port that is still busy from a previous PRINT or WX or RX instruction.
5113
Network Instructions
Read from Network The Read from Network instruction is used (RX) by the master device on a network to read a block of data from another CPU. The RX function parameters are loaded into the A aaa first and second level of the accumulator stack and the accumulator by three additional instructions. Listed below are the steps necessary to program the Read from Intelligent module function. Step 1: Load the slave address (090 BCD) into the first byte and F2 into the second byte of the second level of the accumulator stack. Step 2: Load the number of bytes to be transferred into the first level of the accumulator stack. Step 3: Load the address of the data to be read into the accumulator. This parameter requires a HEX value. Step 4: Insert the RX instruction which specifies the starting V memory location (Aaaa) where the data will be read from in the slave. Helpful Hint: For parameters that require HEX values, the LDA instruction can be used to convert an octal address to the HEX equivalent and load the value into the accumulator.
Operand Data Type A V memory Pointer Inputs Outputs Control Relays Stage Timer Counter Special Relay Program Memory V P X Y C S T CT SP $ DL05 Range aaa All (See page 428) All V mem. (See page 428) 01777 01777 03777 01777 0377 0377 0137 320717 02047 (2K program mem.)
5114
In the following example, when X1 is on and the port busy relay SP116 (see special relays) is not on, the RX instruction will access port 2 operating as a master. Ten consecutive bytes of data (V2000 V2004) will be read from a CPU at station address 5 and copied into V memory locations V2300V2304 in the CPU with the master port.
DirectSOFT
X1 SP116 LD KF205 The constant value K0205 specifies the slot number (2) and the slave address (5) LD K10 The constant value K10 specifies the number of bytes to be read LDA O 2300 Octal address 2300 is converted to 4C0 HEX and loaded into the accumulator. V2300 is the starting location for the Master CPU where the specified data will be read into RX V2000 V2000 is the starting location in the for the Slave CPU where the specified data will be read from V2277 V2300 V2301 V2302 V2303 V2304 V2305 X 3 8 1 9 1 X X 4 5 9 5 4 X S S
Master CPU
S S X 5 3 3 7 2 X X 7 4 6 1 3 X
Slave CPU
S S X 3 8 1 9 1 X X 4 5 9 5 4 X S S X 5 3 3 7 2 X X V1777 7 4 6 1 3 V2000 V2001 V2002 V2003 V2004
X V2005
Handheld Programmer Keystrokes $ STR W ANDN SHFT SHFT SHFT SHFT L ANDST L ANDST L ANDST R ORN B 1 SHFT D 3 D 3 D 3 X SET A 0 C 2 A 0 ENT SP STRN B 1 SHFT SHFT B 1 K JMP K JMP C 2 A 0 C 2 B 1 D 3 A 0 A 0 A 0 G 6 ENT A 0 F 5 ENT A 0 ENT ENT ENT
5115
The Write to Network instruction is used to write a block of data from the master device to a slave device on the same WX network. The function parameters are A aaa loaded into the first and second level of the accumulator stack and the accumulator by three additional instructions. Listed below are the steps necessary to program the Write to Network function. Step 1: Load the slave address (090 BCD) into the first byte and the number of the master port into the second byte of the second level of the accumulator stack. Step 2: Load the number of bytes to be transferred into the first level of the accumulator stack. Step 3: Load the address of the data in the master that is to be written to the network into the accumulator. This parameter requires a HEX value. Step 4: Insert the WX instruction which specifies the starting V memory location (Aaaa) where the data will be written to the slave. Helpful Hint: For parameters that require HEX values, the LDA instruction can be used to convert an octal address to the HEX equivalent and load the value into the accumulator.
Operand Data Type A V memory Pointer Inputs Outputs Control Relays Stage Timer Counter Special Relay Program Memory V P X Y C S T CT SP $ DL05 Range aaa All (See page 428) All V mem. (See page 428) 01777 01777 03777 01777 0377 0377 0137 320717 02048 (2K program mem.)
5116
In the following example when X1 is on and the module busy relay SP116 (see special relays) is not on, the RX instruction will access port 2 operating as a master. Ten consecutive bytes of data is read from the CPU at station address 5 and copied to V memory locations V2000V2004 in the slave CPU.
DirectSOFT
X1 SP116 LD K205 The constant value K0205 specifies the slot number (2) and the slave address (5) LD K10 The constant value K10 specifies the number of bytes to be read LDA O 2300 Octal address 2300 is converted to 4C0 HEX and loaded into the accumulator. V2300 is the starting location for the Master CPU where the specified data will be read from. V2277 V2300 V2301 V2302 V2303 V2304 V2305 X 3 8 1 9 1 X X 4 5 9 5 4 X S S
Master CPU
S S X 5 3 3 7 2 X X 7 4 6 1 3 X
Slave CPU
S S X 3 8 1 9 1 X X 4 5 9 5 4 X S S X 5 3 3 7 2 X X V1777 7 4 6 1 3 V2000 V2001 V2002 V2003 V2004
X V2005
WX V2000 V2000 is the starting location in the for the Slave CPU where the specified data will be written to Handheld Programmer Keystrokes $ STR W ANDN SHFT SHFT SHFT SHFT L ANDST L ANDST L ANDST W ANDN B 1 SHFT D 3 D 3 D 3 X SET A 0 SHFT ENT SP STRN B 1 SHFT SHFT C 2 K JMP K JMP SHFT V AND C 2 B 1 O INST# C 2 C 2 A 0 A 0 A 0 E 4 ENT A 0 F 5 ENT D 3 A 0 A 0 A 0 ENT ENT ENT
16
62
Drum Instruction Programming
Introduction
The Event Drum (EDRUM) instruction in the DL05 CPU electronically simulates an electro-mechanical drum sequencer. The instruction offers enhancements to the basic principle, which we describe first. Drum Terminology Drum instructions are best suited for repetitive processes that consist of a finite number of steps. They can do the work of many rungs of ladder logic with elegant simplicity. Therefore, drums can save a lot of programming and debugging time. We introduce some terminology associated with the drum instruction by describing the original mechanical drum shown below. The mechanical drum generally has pegs on its curved surface. The pegs are populated in a particular pattern, representing a set of desired actions for machine control. A motor or solenoid rotates the drum a precise amount at specific times. During rotation, stationary wipers sense the presence of pegs (present = on, absent = off). This interaction makes or breaks electrical contact with the wipers, creating electrical outputs from the drum. The outputs are wired to devices on a machine for On/Off control. Drums usually have a finite number of positions within one rotation, called steps. Each step represents some process step. At powerup, the drum resets to a particular step. The drum rotates from one step to the next based on a timer, or on some external event. During special conditions, a machine operator can manually increment the drum step using a jog control on the drums drive mechanism. The contact closure of each wiper generates a unique on/off pattern called a sequence, designed for controlling a specific machine. Because the drum is circular, it automatically repeats the sequence once per rotation. Applications vary greatly, and a particular drum may rotate once per second, or as slowly as once per week. Purpose
Pegs
Wipers Drum
Outputs
Electronic drums provide the benefits of mechanical drums and more. For example, they have a preset feature that is impossible for mechanical drums: The preset function lets you move from the present step directly to any other step on command!
63
Drum Instruction Programming
For editing purposes, the electronic drum is presented in chart form in DirectSOFT and in this manual. Imagine slicing the surface of a hollow drum cylinder between two rows of pegs, then pressing it flat. Now you can view the drum as a chart as shown below. Each row represents a step, numbered 1 through 16. Each column represents an output, numbered 0 through 15 (to match word bit numbering). The solid circles in the chart represent pegs (On state) in the mechanical drum, and the open circles are empty peg sites (Off state).
OUTPUTS STEP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 f F f F f f F f f f F f f F f f 2 f F f F F f F f f f f F f f F f 3 f F F F F f F F f f f f f f f f 4 F F f F F f F f F f f f f f f F 5 f f f F f f F f F f F f F f f F 6 f f f F f f F f F f F f F F f F 7 F f f F f f F F F F f F F F f F 8 F f F f f F f F F f f f F f f F 9 f f f f f f f F F f f f F f f f 10 f f f f f f f F F F f f f f f f 11 F f f f F f f f f F f f f f F f 12 f F f f F F f f F f F F f F F f 13 f f F f f f f f f f f F F f F f 14 f f f f f f f F f f f F F f F F 15 F f f f f F f F f F f F f f F F 16 f f F f f f f F f F f F F f f F
Output Sequences The mechanical drum sequencer derives its name from sequences of control changes on its electrical outputs. The following figure shows the sequence of On/Off controls generated by the drum pattern above. Compare the two, and you will find that they are equivalent! If you can see their equivalence, you are well on your way to understanding drum instruction operation.
Step Output 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
64
Drum Instruction Programming
Step Transitions
Drum Instruction Types There are two types of Drum instructions in the DL05 CPU: S Timed Drum with Discrete Outputs (DRUM) S Time and Event Drum with Discrete Outputs (EDRUM) The two drum instructions include time-based step transitions, and the EDRUM includes event-based transitions as well. Each drum has 16 steps, and each step has 16 outputs. Refer to the figure below. Each output can be either an X, Y, or C coil, offering programming flexibility. We assign Step 1 an arbitrary unique output pattern (f= Off, F= On) as shown. When programming a drum instruction, you also determine both the output assignment and the On/Off state (pattern) at that time. All steps use the same output assignment, but each step may have its own unique output pattern. Drums move from one step to another based on time and/or an external event (input). Each step has its own transition condition which you assign during the drum instruction entry. The figure below shows how timer-only transitions work.
Step 1 Outputs:
F f f f F f F f f f f F F f f f
Timer-Only Transitions
No
Step 2
Outputs:
f f f F f f f f F F f F f f F F
The drum stays in Step 1 for a specific duration (user-programmable). The timebase of the timer is programmable, from 0.01 seconds to 99.99 seconds. This establishes the resolution, or the duration of each tick of the clock. Each step uses the same timebase, but has its own unique counts per step, which you program. When the counts for Step 1 have expired, then the drum moves to Step 2. The outputs change immediately to match the new pattern for Step 2. The drum spends a specific amount of time in each step, given by the formula: Time in step = 0.01 seconds X Timebase x Counts per step
65
Drum Instruction Programming
For example, if you program a 5 second time base and 12 counts for Step 1, then the drum will spend 60 seconds in Step 1. The maximum time for any step is given by the formula: Max Time per step = 0.01 seconds X 9999 X 9999 = 999,800 seconds = 277.7 hours = 11.6 days NOTE: When first choosing the timebase resolution, a good rule of thumb is to make it about 1/10 the duration of the shortest step in your drum. Then you will be able to optimize the duration of that step in 10% increments. Other steps with longer durations allow optimizing by even smaller increments (percentage-wise). Also, note that the drum instruction executes once per CPU scan. Therefore, it is pointless to specify a drum timebase that is much faster than the CPU scan time.
Step transitions may also occur based on time and/or external events. The figure below shows how step transitions work in these cases.
Step 1 Outputs:
F f f f F f F f f f f F F f f f
No
No
Step 2
Outputs:
f f f F f f f f F F f F f f F F
When the drum enters Step 1, it sets the output pattern as shown. Then it begins polling the external input programmed for that step. You can define event inputs as X, Y, or C discrete point types. Suppose we select X0 for the Step 1 event input. If X0 is off, then the drum remains in Step 1. When X0 is On, the event criteria is met and the timer increments. The timer increments as long as the event (X0) remains true. When the counts for Step 1 have expired, then the drum moves to Step 2. The outputs change immediately to match the new pattern for Step 2.
66
Drum Instruction Programming
Event-Only Transitions
Step transitions do not require both the event and the timer criteria programmed for each step. You have the option of programming just one of the two, and even mixing transition types among all the steps of the drum. For example, you might want Step 1 to transition on an event, Step 2 to transition on time only, and Step 3 to transition on both time and an event. Furthermore, you may elect to use only part of the 16 steps, and only part of the 16 outputs.
Step 1 Outputs:
F f f f F f F f f f f F F f f f
No
Step 2
Outputs:
f f f F f f f f F F f F f f F F
Counter Assignments
Each drum instruction uses the resources of four counters in the CPU. When programming the drum instruction, you select the first counter number. The drum also uses the next three counters automatically. The counter bit associated with the first counter turns on when the drum has completed its cycle, going off when the drum is reset. These counter values and the counter bit precisely indicate the progress of the drum instruction, and can be monitored by your ladder program. Suppose we program a timer drum to have 8 steps, and we select CT10 for the counter number (remember, counter numbering is in octal). Counter usage is shown to the right. The right column holds typical values, interpreted below.
Counter Assignments
CT10 Counts in step V1010 CT11 Timer Value CT12 Preset Step CT13 Current Step V1011 V1012 V1013 1528 0200 0001 0004
CT10 shows that we are at the 1528th count in the current step, which is step 4 (shown in CT13). If we have programmed step 4 to have 3000 counts, then the step is just over half completed. CT11 is the count timer, shown in units of 0.01 seconds. So, each least-significant-digit change represents 0.01 seconds. The value of 200 means that we have been in the current count (1528) for 2 seconds (0.01 x 100). Finally, CT12 holds the preset step value which was programmed into the drum instruction. When the drums Reset input is active, it presets to step 1 in this case. The value of CT12 changes only if the ladder program writes to it, or the drum instruction is edited and the program is restarted. Counter bit CT10 turns on when the drum cycle is complete, and turns off when the drum is reset.
67
Drum Instruction Programming
The last step in a drum sequence may be any step number, since partial drums are valid. Refer to the following figure. When the transition conditions of the last step are met, the drum sets the counter bit corresponding to the counter named in the drum instruction box (such as CT0). Then it moves to a final drum complete state. The drum outputs remain in the pattern defined for the last step. Having finished a drum cycle, the Start and Jog inputs have no effect at this point. The drum leaves the drum complete state when the Reset input becomes active (or on a program-torun mode transition). It resets the drum complete bit (such as CT0), and then goes directly to the appropriate step number defined as the preset step.
Last step Outputs:
F F F f f f F f f F f F F F f F
No
Complete
Outputs:
F F F f f f F f f F f F F F f F
No
Reset Input Active? Yes Reset CT0 = 0 Reset Drum Complete bit
Go to Preset Step
68
Drum Instruction Programming
Outputs
Counter Assignments
CT0 CT1 CT2 CT3
The drum instruction accepts several inputs for step control, the main control of the drum. The inputs and their functions are: S Start The Start input is effective only when Reset is off. When Start is on, the drum timer runs if it is in a timed transition, and the drum looks for the input event during event transitions. When Start is off, the drum freezes in its current state (Reset must remain off), and the drum outputs maintain their current on/off pattern. Jog The jog input is only effective when Reset is off (Start may be either on or off). The jog input increments the drum to the next step on each off-to-on transition (only EDRUM supports the jog input). Reset The Reset input has priority over the Start input. When Reset is on, the drum moves to its preset step. When Reset is off, then the Start input operates normally. Preset Step A step number from 1 to 16 that you define (typically is step 1). The drum moves to this step whenever Reset is on, and whenever the CPU first enters run mode.
S S S
69
Drum Instruction Programming
Counts/Step The number of timer counts the drum spends in each step. Each step has its own counts parameter. However, programming the counts/step is optional. Timer Value the current value of the counts/step timer. Counter # The counter number specifies the first of four consecutive counters which the drum uses for step control. You can monitor these to determine the drums progress through its control cycle. The DL05 has 128 counters (CT0 CT177 in octal). Events Either an X, Y, C, S, T, or CT type discrete point serves as step transition inputs. Each step has its own event. However, programming the event is optional.
WARNING: The outputs of a drum are enabled any time the CPU is in Run Mode. The Start Input does not have to be on, and the Reset input does not disable the outputs. Upon entering Run Mode, drum outputs automatically turn on or off according to the pattern of the current step of the drum. This initial step number depends on the counter memory configuration: non-retentive versus retentive. Powerup State of Drum Registers The choice of the starting step on powerup and program-to-run mode transitions are important to consider for your application. Please refer to the following chart. If the counter memory is configured as non-retentive, the drum is initialized the same way on every powerup or program-to-run mode transition. However, if the counter memory is configured to be retentive, the drum will stay in its previous state.
Counter Number CT(n) CT(n + 1) CT(n + 2) CT(n + 3) Function Initialization on Powerup Non-Retentive Case Current Step Count Counter Timer Value Preset Step Current Step # Initialize = 0 Initialize = 0 Initialize = Preset Step # Initialize = Preset Step # Retentive Case Use Previous (no change) Use Previous (no change) Use Previous (no change) Use Previous (no change)
Applications with relatively fast drum cycle times typically will need to be reset on powerup, using the non-retentive option. Applications with relatively long drum cycle times may need to resume at the previous point where operations stopped, using the retentive case. The default option is the retentive case. This means that if you initialize scratchpad V-memory, the memory will be retentive.
610
Drum Instruction Programming
Setup Info.
Outputs
The timing diagram below shows an arbitrary timer drum input sequence and how the drum responds. As the CPU enters Run mode it initializes the step number to the preset step number (typically it is Step 1). When the Start input turns on the drum begins running, waiting for an event and/or running the timer (depends on the setup). After the drum enters Step 2, Reset turns On while Start is still On. Since Reset has priority over Start, the drum goes to the preset step (Step 1). Note that the drum is held in the preset step during Reset, and that step does not run (respond to events or run the timer) until Reset turns off. After the drum has entered step 3, the Start input goes off momentarily, halting the drums timer until Start turns on again.
Start drum Inputs Start Jog Reset Drum Status Step # Drum Complete (CT0) Outputs (x 16)
1 0 1 0 1 1 2 1 1 2 3 3 4 ... 15 16 16 16 1 1
Reset drum
Hold drum
Resume drum
1 0 1 0 1 0
When the drum completes the last step (Step 16 in this example), the Drum Complete bit (CT0) turns on, and the step number remains at 16. When the Reset input turns on, it turns off the Drum Complete bit (CT0), and forces the drum to enter the preset step. NOTE: The timing diagram shows all steps using equal time durations. Step times can vary greatly, depending on the counts/step programmed.
611
Drum Instruction Programming
In the figure below, we focus on how the Jog input works on event drums. To the left of the diagram, note that the off-to-on transitions of the Jog input increments the step. Start may be either on or off (however, Reset must be off). Two jogs takes the drum to step three. Next, the Start input turns on, and the drum begins running normally. During step 6 another Jog input signal occurs. This increments the drum to step 7, setting the timer to 0. The drum begins running immediately in step 7, because Start is already on. The drum advances to step 8 normally. As the drum enters step 14, the Start input turns off. Two more Jog signals moves the drum to step 16. However, note that a third Jog signal is required to move the drum through step 16 to drum complete. Finally, a Reset input signal arrives which forces the drum into the preset step and turns off the drum complete bit.
Jog drum Inputs Start Jog Reset Drum Status Step # Drum Complete (CT0) Outputs (x 16)
1 0 1 0 1 2 3 3 3 4 5 6,7 8 ... 14 15 16 16 16 1
Reset drum
Jog drum
Jog drum
Drum Complete
1 0 1 0 1 0
Self-Resetting Drum
Applications often require drums that automatically start over once they complete a cycle. This is easily accomplished, using the drum complete bit. In the figure to the right, the drum instruction setup is for CT0, so we logically OR the drum complete bit (CT0) with the Reset input. When the last step is done, the drum turns on CT0 which resets itself to the preset step, also resetting CT0. Contact X2 still works as a manual reset.
X0 X1
Outputs
f f f F F F F F F f f f F F f F f f f F f f f f f f f f F f F f F f F F F F f F
X2 CT0
The outputs of a drum are enabled any time the CPU is in run mode. On program-to-run mode transitions, the drum goes to the preset step, and the outputs energize according to the pattern of that step. If your application requires all outputs to be off at powerup, make the preset step in the drum a reset step, with all outputs off. Each event-based transition accepts only one contact reference for the event. However, this does not limit events to just one contact. Just use a control relay contact such as C0 for the step transition event. Elsewhere in ladder logic, you may use C0 as an output coil, making it dependent on many other events (contacts).
612
Drum Instruction Programming
Drum Instruction
The DL05 drum instructions may be programmed using DirectSOFT or for the EDRUM instruction only you can use a handheld programmer (firmware version v1.8 or later. This section covers entry using DirectSOFT for all instructions plus the handheld mnemonics for the EDRUM instruction. The Timed Drum with Discrete Outputs is the most basic of the DL05s drum instructions. It operates according to the principles covered on the previous pages. Below is the instruction in chart form as displayed by DirectSOFT.
Counter Number
DRUM ms/Count Step # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CT aaa K cccc Counts Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd Kdddd
15
Start
Control Inputs
Step Preset K bb
(Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff) (Fffff)
Reset
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
The Timed Drum features 16 steps and 16 outputs. Step transitions occur only on a timed basis, specified in counts per step. Unused steps must be programmed with counts per step = 0 (this is the default entry). The discrete output points may be individually assigned as X, Y, or C types, or may be left unused. The output pattern may be edited graphically with DirectSOFT. Whenever the Start input is energized, the drums timer is enabled. It stops when the last step is complete, or when the Reset input is energized. The drum enters the preset step chosen upon a CPU program-to-run mode transition, and whenever the Reset input is energized.
Drum Parameters Counter Number Preset Step Timer base Counts per step Discrete Outputs Field aaa bb cccc dddd Fffff Data Types K K K X, Y, C Ranges 0 174 1 16 0 99.99 seconds 0 9999 see page 428
613
Drum Instruction Programming
Drum instructions use four counters in the CPU. The ladder program can read the counter values for the drums status. The ladder program may write a new preset step number to CT(n+2) at any time. However, the other counters are for monitoring purposes only.
Counter Number CT(n) CT( n+1) CT( n+2) CT( n+3) Ranges of (n) 0 174 1 175 2 176 3 177 Function Counts in step Timer value Preset Step Current Step Counter Bit Function CTn = Drum Complete CT(n+1) = (not used) CT(n+2) = (not used) CT(n+3) = (not used)
The following ladder program shows the DRUM instruction in a typical ladder program, as shown by DirectSOFT. Steps 1 through 10 are used, and twelve of the sixteen output points are used. The preset step is step 1. The timebase runs at 100 mS per count. Therefore, the duration of step 1 is (25 x 0.1) = 2.5 seconds. In the last rung, the Drum Complete bit (CT0) turns on output Y0 upon completion of the last step (step 10). A drum reset also resets CT0.
DirectSOFT Display
X0
Start Reset
CT 0 K 100 Counts K0025 K0020 K1500 K0045 K0180 K0923 K1200 K8643 K1200 K4000
15 ( ) ( ) ( ) ( )
0 (C14) (Y10) (C4) (Y5) (Y13) (C7) (C30) (Y20) (C2) (Y6) (Y42) (C10)
Step Preset K 1
X1
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
F F f f f F F f F f f f f f f f
f f F f F f f F F F f f f f f f
f F f F f f F f F f f f f f f f
F f F f f F f f F F f f f f f f
F f f F f f F F F f f f f f f f
f F F f F f f f F F f f f f f f
f f f f f F F F F f f f f f f f
F f f F f f f f F F f f f f f f
f f F f f f f f F f f f f f f f
f f f f F F f f F F f f f f f f
f F f F f f F F F f f f f f f f
F f F f f F f F F f f f f f f f
CT0
Drum Complete
Y0 OUT
614
Drum Instruction Programming
The Event Drum (EDRUM) features time-based and event-based step transitions. It operates according to the general principles of drum operation covered in the beginning of this chapter. Below is the instruction as displayed by DirectSOFT.
Counter Number Step Preset Timebase
Start EDRUM ms/Count Step # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CT aa K cccc
15
EDRUM2
Control Inputs
Jog Reset
Step Preset K bb Counts Event Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee Kdddd Eeeee
(Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff) (Ffff)
Step Number Counts per Step Event per step Output Pattern
f= Off, F= On
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
f f f f f f f f f f f f f f f f
The Event Drum features 16 steps and 16 discrete outputs. Step transitions occur on timed and/or event basis. The jog input also advances the step on each off-to-on transition. Time is specified in counts per step, and events are specified as discrete contacts. Unused steps must be programmed with counts per step = 0, and event = K0000. The discrete output points may be individually assigned. Whenever the Start input is energized, the drums timer is enabled. As long as the event is true for the current step, the timer runs during that step. When the step count equals the counts per step, the drum transitions to the next step. This process stops when the last step is complete, or when the Reset input is energized. The drum enters the preset step chosen upon a CPU program-to-run mode transition, and whenever the Reset input is energized.
Drum Parameters Counter Number Preset Step Timer base Counts per step Event Discrete Outputs Field aa bb cccc dddd eeee ffff Data Types K K K X, Y, C, S, T, CT X, Y, C Ranges 0 174 1 16 0.01 99.99 seconds 0 9999 see page 428 see page 428
615
Drum Instruction Programming
Drum instructions use four counters in the CPU. The ladder program can read the counter values for the drums status. The ladder program may write a new preset step number to CT(n+2) at any time. However, the other counters are for monitoring purposes only.
Counter Number CT(n) C( n+1) CT( n+2) CT( n+3) Ranges of (n) 0 174 1 175 2 176 3 177 Function Counts in step Timer value Preset Step Current Step Counter Bit Function CTn = Drum Complete CT(n+1) = (not used) CT(n+2) = (not used) CT(n+3) = (not used)
The following ladder program shows the EDRUM instruction in a typical ladder program, as shown by DirectSOFT. Steps 1 through 11 are used, and all sixteen output points are used. The preset step is step 1. The timebase runs at 100 mS per count. Therefore, the duration of step 1 is (5 x 0.1) = 0.5 seconds. Note that step 1 is time-based only (event = K0000). And, the output pattern for step 1 programs all outputs off, which is a typically desirable powerup condition. In the last rung, the Drum Complete bit (CT4) turns on output Y0 upon completion of the last step (step 10). A drum reset also resets CT4.
DirectSOFT Display
X0 X1 X2
CT 4 K 100
15
Step Preset K 1 Counts Event K0005 K0000 K0020 Y4 K0150 X1 K0048 X2 K0180 C0 K0923 C1 K0120 X0 K0864 X5 K1200 X3 K0400 Y7 K0000 C20 K0000 Eeeee K0000 Eeeee K0000 Eeeee K0000 Eeeee K0000 Eeeee
(C34) (Y6) (C14) (Y0) (C4) (Y5) (Y1) (C7) (Y3) (Y7) (C30) (Y2) (C2) (Y6) (Y4) (C10)
f F f f f F f F f f F f f f f f
f f f F F f F f f F f f f f f f
f f F f f f f f f f f f f f f f
f F f f F F f F f F f f f f f f
f F F f f f f f f F f f f f f f
f f f F f f F f f f F f f f f f
f f f f f F f F F f f f f f f f
f f f f F F f f F f f f f f f f
f f F f f f F f F f f f f f f f
f f f F F F f F f F F f f f f f
f f f F F f f f f F f f f f f f
f F F F f f f F f f f f f f f f
f f f f F f f F F f f f f f f f
f f F F f f F f f F F f f f f f
Y0 OUT
f F f F f F F f F f F f f f f f
f f f f F F f F f f F f f f f f
CT4
Drum Complete
616
Drum Instruction Programming
The EDRUM instruction may be programmed using either DirectSOFT or a handheld programmer. This section covers entry via the handheld programmer (Refer to the DirectSOFT manual for drum instruction entry using that tool). First, enter Store instructions for the ladder rungs controlling the drums ladder inputs. In the example to the right, the timer drums Start, Jog, and Reset inputs are controlled by X0, X1 and X2 respectively. The required keystrokes are listed beside the mnemonic. These keystrokes precede the EDRUM instruction mnemonic. Note that the ladder rungs for Start, Jog, and Reset inputs are not limited to being singlecontact rungs.
X0 X1 X2
Outputs Mask
f f f F F F F F F f f f F F f F f f f F f f f f f f f f F f F f F f F F F F f F
Store X0
$ STR
A 0
ENT
After the Store instructions, enter the EDRUM (using Counter CT0) as shown:
Handheld Programmer Keystrokes
EDRUM CNT0
SHFT
E 4
D 3
R ORN
U ISG
M ORST
A 0
ENT
After entering the EDRUM mnemonic as above, the handheld programmer creates an input form for all the drum parameters. The input form consists of approximately fifty or more default mnemonic entries containing DEF (define) statements. The default mnemonics are already input for you, so they appear automatically. Use the NXT and PREV keys to move forward and backward through the form. Only the editing of default values is required, thus eliminating many keystrokes. The entries required for the basic timer drum are in the chart below.
Drum Parameters Start Input Jog Input Reset Input Drum Mnemonic Preset Step Timer base Output points Counts per step Events Output pattern Multiple Entries 1 1 16 16 16 16 Mnemonic / Entry STR (plus input rung) STR (plus input rung) STR (plus input rung) DRUM CNT aa bb cccc ffff dddd dddd gggg DEF K0000 DEF K0000 DEF 0000 DEF K0000 DEF K0000 DEF K0000 Default Mnemonic Valid Data Types CT K K X, Y, C * K X, Y, C, S, T, CT K Ranges 0 174 1 16 1 9999 see page 428 0 9999 see page 428 0 FFFF
NOTE: Default entries for output points and events are DEF 0000, which means they are unassigned. If you need to go back and change an assigned output as unused again, enter K0000. The entry will again show as DEF 0000.
617
Drum Instruction Programming
Using the DRUM entry chart (two pages before), we show the method of entry for the basic time/event drum instruction. First, we convert the output pattern for each step to the equivalent hex number, as shown in the following example.
Step 1 Outputs:
f f f f F f f F f f f F F f F f
converts to:
15
The following diagram shows the method for entering the previous EDRUM example on the HHP. The default entries of the form are in parenthesis. After the drum instruction entry (on the fourth row), the remaining keystrokes over-write the numeric portion of each default DEF statement. NOTE: Drum editing requires Handheld Programmer firmware version 1.7 or later.
Handheld Programmer Keystrokes
A 0 B 1 C 2 D 3
ENT ENT ENT R ORN NEXT G 6 SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT C 2 C 2 Y MLS Y MLS Y MLS Y MLS C 2 C 2 Y MLS Y MLS C 2 C 2 Y MLS Y MLS C 2 Y MLS B 1 G 6 H 7 D 3 D 3 A 0 C 2 B 1 A 0 NEXT NEXT E 4 NEXT NEXT C 2 B 1 E 4 F 5 G 6 E 4 B 1 E 4 U ISG M ORST A 0 ENT
NOTE: You may use the NXT and PREV keys to skip past entries for unused outputs or steps.
( DEF K0001) ( DEF K0000 ) ( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 )
Handheld Programmer Keystrokes contd NEXT H 7 NEXT A 0 NEXT NEXT NEXT NEXT NEXT NEXT NEXT NEXT E 4 NEXT NEXT NEXT 1 ( DEF K0000 ) ( DEF K0000 ) F 5 C 2 B 1 E 4 B 1 J 9 B 1 I 8 B 1 E 4 NEXT NEXT NEXT NEXT NEXT NEXT A 0 C 2 A 0 G 6 A 0 C 2 E 4 C 2 A 0 I 8 D 3 F 5 F 5 NEXT A 0 NEXT A 0 NEXT A 0 NEXT NEXT NEXT NEXT A 0 NEXT NEXT NEXT
Outputs
( DEF 0000 ) ( DEF 0000 )
Counts/ Step
( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 )
( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 ) 16 ( DEF 0000 )
16 ( DEF K0000 )
618
Drum Instruction Programming
Handheld Programmer Keystrokes contd 1 ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 )
NEXT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT NEXT NEXT NEXT NEXT NEXT Y MLS X SET X SET C 2 C 2 X SET X SET X SET Y MLS C 2
( DEF 0000 )
Events
( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 ) ( DEF 0000 )
Output Pattern
( DEF K0000 )
( DEF K0000 )
( DEF K0000 ) A 0 NEXT ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) ( DEF K0000 ) 16 ( DEF K0000 ) $
unused steps
Last rung
STR SHFT
NEXT NEXT
NOTE: You may use the NXT and PREV keys to skip past entries for unused outputs or steps.
17
Introduction to Stage Programming Learning to Draw State Transition Diagrams Using the Stage Jump Instruction for State Transitions Stage Program Example: Toggle On/Off Lamp Controller Four Steps to Writing a Stage Program Stage Program Example: A Garage Door Opener Stage Program Design Considerations RLL PLUS (Stage) Instructions Questions and Answers about Stage Programs
72
73
PLC Scan
1) Read 2) Read 3) Read Execute Execute (etc....) Write Write
Most manufacturing processes consist of a series of activities or conditions , each lasting for several seconds. minutes, or even hours. We might call these process states, which are either active or inactive at any particular time. A challenge for RLL programs is that a particular input event may last for just a brief instant. We typically create latching relays in RLL to preserve the input event in order to maintain a process state for the required duration. We can organize and divide ladder logic into sections called stages, representing process states. But before we describe stages in detail, we will reveal the secret to understanding stage programming: state transition diagrams. The Need for State Sometimes we need to forget about the scan nature of PLCs, and focus our thinking toward the states of the process we need to identify. Clear thinking and concise Diagrams analysis of an application gives us the best chance at writing efficient, bug-free programs. State diagrams are just a tool to help us draw a picture of our process! Youll discover that if we can get the picture right, our program will also be right! A 2State Process Consider the simple process shown to the Inputs Outputs right, which controls an industrial motor. On X0 We will use a green momentary SPST Motor pushbutton to turn the motor on, and a red Ladder Y0 one to turn it off. The machine operator will Program Off X1 press the appropriate pushbutton for just a second or so. The two states of our process are ON and OFF. Transition condition The next step is to draw a state transition State diagram, as shown to the right. It shows X0 the two states OFF and ON, with two transition lines in-between. When the OFF ON event X0 is true, we transition from OFF to X1 ON. When X1 is true, we transition from Output equation: Y0 = ON ON to OFF. If youre following along, you are very close to grasping the concept and the problem-solving power of state transition diagrams. The output of our controller is Y0, which is true any time we are in the ON state. In a boolean sense, Y0=ON state. Next, we will implement the state diagram first as RLL, then as a stage program. This will help you see the relationship between the two methods in problem solving.
74
The state transition diagram to the right is a picture of the solution we need to create. The beauty of it is this: it expresses the problem independently of the programming language we may use to realize it. In other words, by drawing the diagram we have already solved the control problem!
X0
OFF
X1
ON
Output equation: Y0 = ON
First, well translate the state diagram to traditional RLL. Then well show how easy it is to translate the diagram into a stage programming solution. RLL PLUS Stage Programming RLL Equivalent The RLL solution is shown to the right. It consists of a self-latching control relay, C0. When the On pushbutton (X0) is pressed, output coil C0 turns on and the C0 contact on the second row latches itself on. So, X0 sets the latch C0 on, and it remains on after the X0 contact opens. The motor output Y0 also has power flow, so the motor is now on. When the Off pushbutton (X1) is pressed, it opens the normally-closed X1 contact, which resets the latch. Motor output Y0 turns off when the latch coil C0 goes off. The stage program solution is shown to the right. The two inline stage boxes S0 and S1 correspond to the two states OFF and ON. The ladder rung(s) below each stage box belong to each respective stage. This means that the PLC only has to scan those rungs when the corresponding stage is active! For now, lets assume we begin in the OFF State, so stage S0 is active. When the On pushbutton (X0) is pressed, a stage transition occurs. The JMP S1 instruction executes, which simply turns off the Stage bit S0 and turns on Stage bit S1. So on the next PLC scan, the CPU will not execute Stage S0, but will execute stage S1! In the On State (Stage S1), we want the motor to always be on. The special relay contact SP1 is defined as always on, so Y0 turns the motor on.
Set
X0
Reset
X1
Latch
C0 OUT
Latch
C0
Output
Y0 OUT
Stage Equivalent
SG S0
SG S1
ON State Output
SP1 Always on Y0 OUT
Transition
X1 S0 JMP
When the Off pushbutton (X1) is pressed, a transition back to the Off State occurs. The JMP S0 instruction executes, which simply turns off the Stage bit S1 and turns on Stage bit S0. On the next PLC scan, the CPU will not execute Stage S1, so the motor output Y0 will turn off. The Off state (Stage 0) will be ready for the next cycle.
75
Lets Compare
Right now, you may be thinking I dont see the big advantage to Stage Programming... in fact, the stage program is longer than the plain RLL program. Well, now is the time to exercise a bit of faith. As control problems grow in complexity, stage programming quickly out-performs RLL in simplicity, program size, etc. For example, consider the diagram below. Notice how easy it is to correlate the OFF SG and ON states of the state transition OFF State S0 diagram below to the stage program at the S1 X0 right. Now, we challenge anyone to easily identify the same states in the RLL JMP program on the previous page! RLL PLUS Stage Programming
SG S1 SP1
ON State
Y0 OUT S0 JMP
X0
X1
OFF
X1
ON
Initial Stages
At powerup and Program-to-Run Mode transitions, the PLC always begins with all normal stages (SG) off. So, the stage programs shown so far have actually had no way to get started (because rungs are not scanned unless their stage is active). Assume that we want to always begin in the Off state (motor off), which is how the RLL program works. The Initial Stage (ISG) is defined to be active at powerup. In the modified program to the right, we have changed stage S0 to the ISG type. This ensures the PLC will scan contact X0 after powerup, because Stage S0 is active. After powerup, an Initial Stage (ISG) works just like any other stage! We can change both programs so that the motor is ON at powerup. In the RLL below, we must add a first scan relay SP0, latching C0 on. In the stage example to the right, we simply make Stage S1 an initial stage (ISG) instead of S0.
Powerup in ON State
X0 X1 C0 OUT Y0 OUT
Initial Stage
S1 JMP
Powerup in ON State
SG S0 X0 S1 JMP ISG S1 SP1
Initial Stage
Y0 OUT S0 JMP
C0
SP0
X1
First Scan
76
We can mark our desired powerup state as shown to the right, which helps us remember to use the appropriate Initial Stages when creating a stage program. It is permissible to have as many initial stages as the process requires.
Powerup
X0
OFF
X1
ON
What Stage Bits Do You may recall that a stage is just a section of ladder program which is either active or inactive at a given moment. All stage bits (S0 to S377) reside in the PLCs image register as individual status bits. Each stage bit is either a boolean 0 or 1 at any time. Program execution always reads ladder rungs from top to bottom, and from left to right. The drawing below shows the effect of stage bit status. The ladder rungs below the stage instruction continuing until the next stage instruction or the end of program belong to stage 0. Its equivalent operation is shown on the right. When S0 is true, the two rungs have power flow. S If Stage bit S0 = 0, its ladder rungs are not scanned (executed). S If Stage bit S0 = 1, its ladder rungs are scanned (executed).
Actual Program Appearance Functionally Equivalent Ladder
SG S0
S0
The inline stage boxes on the left power rail divide the ladder program rungs into stages. Some stage rules are: S Execution Only logic in active stages are executed on any scan. S Transitions Stage transition instructions take effect on the next occurrence of the stages involved. S Octal numbering Stages are numbered in octal, like I/O points, etc. So S8 is not valid. S Total Stages The DL05 offers up to 256 stages (S0 to S377 in octal). S No duplicates Each stage number is unique and can be used just once. S Any order You can skip numbers and sequence the stage numbers in any order. S Last Stage the last stage in the ladder program includes all rungs from its stage box until the end coil.
SG S0
SG S1
SG S2
END
77
S0
SG S0 X0 S1 JMP
S1
SG S0
Equivalent
X0
S0 RST S1 SET
Please Read Carefully The jump instruction is easily misunderstood. The jump does not occur immediately like a GOTO or GOSUB program control instruction when executed. Heres how it works: S The jump instruction resets the stage bit of the stage in which it occurs. All rungs in the stage still finish executing during the current scan, even if there are other rungs in the stage below the jump instruction! S The reset will be in effect on the following scan, so the stage that executed the jump instruction previously will be inactive and bypassed. S The stage bit of the stage named in the Jump instruction will be set immediately, so the stage will be executed on its next occurrence. In the left program shown below, stage S1 executes during the same scan as the JMP S1 occurs in S0. In the example on the right, Stage S1 executes on the next scan after the JMP S1 executes, because stage S1 is located above stage S0.
Executes on next scan after Jmp
S1 Y0 OUT SG S0 X0 S1 JMP
SG S0 X0 S1 JMP SG S1 S1
SG S1
Note: Assume we start with Stage 0 active and stage 1 inactive for both examples.
78
Powerup
X0
OFF
X0
ON
Output equation: Y0 = ON
Note that this example differs from the motor example, because now we have just one pushbutton. When we press the pushbutton, both transition conditions are met. We would just transition around the state diagram at top speed. If implemented in Stage, this solution would flash the light on or off each scan (obviously undesirable)! The solution is to make the the push and the release of the pushbutton separate events. Refer to the new state transition diagram below. At powerup we enter the OFF state. When switch X0 is pressed, we enter the Press-ON state. When it is released, we enter the ON state. Note that X0 with the bar above it denotes X0 NOT.
Powerup X0
PushON
X0
ISG S0
OFF State
X0 S1 JMP
OFF
PushOFF
ON
X0 Output equation: Y0 = ON
SG S1
X0
PushOn State
X0 S2 JMP
When in the ON state, another push and release cycle similarly takes us back to the OFF state. Now we have two unique states (OFF and ON) used when the pushbutton is released, which is what was required to solve the control problem. The equivalent stage program is shown to the right. The desired powerup state is OFF, so we make S0 an initial stage (ISG). In the ON state, we add special relay contact SP1, which is always on. Note that even as our programs grow more complex, it is still easy to correlate the state transition diagram with the stage program!
SG S2 SP1
ON State Output
Y0 OUT S3 JMP
X0
SG S3 X0
PushOff State
S0 JMP
79
710
In order to identify the inputs and outputs of the system, its sometimes helpful to sketch its main components, as shown in the door side view to the right. The door has an up limit and a down limit switch. Each limit switch closes only when the door has reach the end of travel in the corresponding direction. In the middle of travel, neither limit switch is closed. The motor has two command inputs: raise and lower. When neither input is active, the motor is stopped. The door command is just a simple pushbutton. Whether wall-mounted as shown, or a radio-remote control, all door control commands logical OR together as one pair of switch contacts. Draw the Block Diagram
The block diagram of the controller is Inputs shown to the right. Input X0 is from the pushbutton door control. Input X1 Toggle X0 energizes when the door reaches the full up position. Input X2 energizes when the Up limit door reaches the full down position. When X1 the door is positioned between fully up or down, both limit switches are open. Down limit The controller has two outputs to drive the X2 motor. Y1 is the up (raise the door) command, and Y2 is the down (lower the door) command.
Outputs
Raise Lower
Y2
711
Now we are ready to draw the state transition diagram. Like the previous light bulb controller example, this application also has just one switch for the command input. Refer to the figure below. S When the door is down (DOWN state), nothing happens until X0 energizes. Its push and release brings us to the RAISE state, where output Y1 turns on and causes the motor to raise the door. S We transition to the UP state when the up limit switch (X1) energizes, and turns off the motor. S Then nothing happens until another X0 press-release cycle occurs. That takes us to the LOWER state, turning on output Y2 to command the motor to lower the door. We transition back to the DOWN state when the down limit switch (X2) energizes.
X0
PushUP
Powerup
X0
RAISE
X1
ISG S0 X0
DOWN State
S1 JMP
DOWN
UP
SG S1
PushUP State
X0 S2 JMP
X2
LOWER
X0
PushDOWN
X0
The equivalent stage program is shown to the right. For now, we will assume the door is down at powerup, so the desired powerup state is DOWN. We make S0 an initial stage (ISG). Stage S0 remains active until the door control pushbutton activates. Then we transition (JMP) to Push-UP stage, S1. A push-release cycle of the pushbutton takes us through stage S1 to the RAISE stage, S2. We use the always-on contact SP1 to energize the motors raise command, Y1. When the door reaches the fully-raised position, the up limit switch X1 activates. This takes us to the UP Stage S3, where we wait until another door control command occurs. In the UP Stage S3, a push-release cycle of the pushbutton will take us to the LOWER Stage S5, where we activate Y2 to command the motor to lower the door. This continues until the door reaches the down limit switch, X2. When X2 closes, we transition from Stage S5 to the DOWN stage S0, where we began. NOTE: The only special thing about an initial stage (ISG) is that it is automatically active at powerup. Afterwards, it is just like any other.
SG S2 SP1
RAISE State
Y1 OUT S3 JMP
X1
SG S3 X0
UP State
S4 JMP
SG S4 X0
PushDOWN State
S5 JMP
SG S5 SP1
LOWER State
Y2 OUT S0 JMP
X2
712
Next we will add a safety light feature to the door opener system. Its best to get the main function working first as we have done, then adding the secondary features. The safety light is standard on many commercially-available garage door openers. It is shown to the right, mounted on the motor housing. The light turns on upon any door activity, remaining on for approximately 3 minutes afterwards. This part of the exercise will demonstrate the use of parallel states in our state diagram. Instead of using the JMP instruction, well use the set and reset commands.
Safety light
Modify the To control the light bulb, we add an output Inputs Block Diagram and to our controller block diagram, shown to Toggle the right, Y3 is the light control output. State Diagram X0 In the diagram below, we add an additional state called LIGHT. Whenever the garage owner presses the door control Up limit X1 switch and releases, the RAISE or LOWER state is active and the LIGHT state is simultaneously active. The line to Down limit the Light state is dashed, because it is not X2 the primary path.
Outputs
Y1 Raise
Ladder Program Y2
Lower
Y3
Light
We can think of the Light state as a parallel process to the raise and lower state. The paths to the Light state are not a transition (Stage JMP), but a State Set command. In the logic of the Light stage, we will place a three-minute timer. When it expires, timer bit T0 turns on and resets the Light stage. The path out of the Light stage goes nowhere, indicating the Light stage just becomes inactive, and the light goes out!
Output equations: X0 X0
PushUP
RAISE
X0
X1
DOWN
LIGHT
T0
UP
X0 X2
LOWER
X0
PushDOWN
X0
713
The finished modified program is shown to the right. The shaded areas indicate the program additions. In the Push-UP stage S1, we add the Set Stage Bit S6 instruction. When contact X0 opens, we transition from S1 and go to two new active states: S2 and S6. In the Push-DOWN state S4, we make the same additions. So, any time someone presses the door control pushbutton, the light turns on. Most new stage programmers would be concerned about where to place the Light Stage in the ladder, and how to number it. The good news is that it doesnt matter! S Just choose an unused Stage number, and use it for the new stage and as the reference from other stages. S Placement in the program is not critical, so we place it at the end. You might think that each stage has to be directly under the stage that transitions to it. While it is good practice, it is not required (thats good, because our two locations for the Set S6 instruction make that impossible). Stage numbers and how they are used determines the transition paths. In stage S6, we turn on the safety light by energizing Y3. Special relay contact SP1 is always on. Timer T0 times at 0.1 second per count. To achieve 3 minutes time period, we calculate: 3 min. x 60 sec/min K= 0.1 sec/count K=1800 counts The timer has power flow whenever stage S6 is active. The corresponding timer bit T0 is set when the timer expires. So three minutes later, T0=1 and the instruction Reset S6 causes the stage to be inactive. While Stage S6 is active and the light is on, stage transitions in the primary path continue normally and independently of Stage 6. That is, the door can go up, down, or whatever, but the light will be on for precisely 3 minutes.
ISG S0 X0
DOWN State
S1 JMP
SG S1 X0
PushUP State
S2 JMP S6 SET
SG S2 SP1
RAISE State
Y1 OUT S3 JMP
X1
SG S3 X0
UP State
S4 JMP
SG S4 X0
PushDOWN State
S5 JMP S6 SET
SG S5 SP1
LOWER State
Y2 OUT S0 JMP
X2
SG S6 SP1
LIGHT State
Y3 OUT TMR T0 K1800 T0 S6 RST
714
Some garage door openers today will detect an object under the door. This halts further lowering of the door. Usually implemented with a photocell (electric-eye), a door in the process of being lowered will halt and begin raising. We will define our safety feature to work in this way, adding the input from the photocell to the block diagram as shown to the right. X3 will be on if an object is in the path of the door. Next, we make a simple addition to the state transition diagram, shown in shaded areas in the figure below. Note the new transition path at the top of the LOWER state. If we are lowering the door and detect an obstruction (X3), we then jump to the Push-UP State. We do this instead of jumping directly to the RAISE state, to give the Lower output Y2 one scan to turn off, before the Raise output Y1 energizes.
X0 X0
PushUP
Inputs
Toggle Up limit X0 X1
Outputs
Y1 Raise Lower Light
Ladder Y2 Program
Y3
RAISE
X0
X1
DOWN
X3
LIGHT
T0
UP
X2 and X3
X0
LOWER
X0
PushDOWN
X0
Exclusive Transitions
It is theoretically possible that the down limit (X2) and the obstruction input (X3) could energize at the same moment. In that case, we would jump to the Push-UP and DOWN states simultaneously, which does not make sense. Instead, we give priority to the obstruction by changing the transition condition to the SG LOWER State DOWN state to [X2 AND NOT X3]. This S5 ensures the obstruction event has the SP1 Y2 priority. The modifications we must make OUT to the LOWER Stage (S5) logic are shown to the right. The first rung remains S0 X2 X3 to Push-UP unchanged. The second and third rungs JMP implement the transitions we need. Note S2 X3 the opposite relay contact usage for X3, to DOWN which ensures the stage will execute only JMP one of the JMP instructions.
715
Status
In a typical application, the separate stage sequences above operate as follows: S Powerup Initialization This stage contains ladder rung tasks done just once at powerup. Its last rung resets the stage, so this stage is only active for one scan (or only as many scans that are required). S Main Process this stage sequence controls the heart of the process or machine. One pass through the sequence represents one part cycle of the machine, or one batch in the process. S E-Stop and Alarm Monitoring This stage is always active because it is watching for errors that could indicate an alarm condition or require an emergency stop. It is common for this stage to reset stages in the main process or elsewhere, in order to initialize them after an error condition. S Operator Interface this is another task that must always be active and ready to respond to an operator. It allows an operator interface to change modes, etc. independently of the current main process step. Although we have separate processes, there can be coordination among them. For example, in an error condition, the Status Stage may want to automatically switch the operator interface to the status mode to show error information as shown to the right. The monitor stage could set the stage bit for Status and Reset the stages Control and Recipe.
Operator Interface Control Recipe
Monitor
Set
Status
716
How Instructions We can think of states or stages as simply dividing up our ladder program as Work Inside Stages depicted in the figure below. Each stage contains only the ladder rungs which are needed for the corresponding state of the process. The logic for transitioning out of a stage is contained within that stage. Its easy to choose which ladder rungs are active at powerup by using an initial stage type (ISG).
Stage 0 Stage 1
Stage 2
Most all instructions work just like they do in standard RLL. You can think of a stage just like a miniature RLL program which is either active or inactive. Output Coils As expected, output coils in active stages will turn on or off outputs according to power flow into the coil. However, note the following: S Outputs work as usual, provided each output reference (such as Y3) is used in only one stage. S An output can be referenced from more than one stage, as long as only one of the stages is active at a time. S If an output coil is controlled by more than one stage simultaneously, the active stage nearest the bottom of the program determines the final output status during each scan. Therefore, use the OROUT instruction instead when you want multiple stages to have a logical OR control of an output. One-Shot or PD coils Use care if you must use a Positive Differential coil in a stage. Remember that the input to the coil must make a 01 transition. If the coil is already energized on the first scan when the stage becomes active, the PD coil will not work. This is because the 01 transition did not occur. PD coil alternative: If there is a task which you want to do only once (on 1 scan), it can be placed in a stage which transitions to the next stage on the same scan. Counter In using a counter inside a stage, the stage must be active for one scan before the input to the counter makes a 01 transition. Otherwise, there is no real transition and the counter will not count. The ordinary Counter instruction does have a restriction inside stages: it may not be reset from other stages using the RST instruction for the counter bit. However, the special Stage counter provides a solution (see next paragraph). Stage Counter The Stage Counter has the benefit that its count may be globally reset from other stages by using the RST instruction. It has a count input, but no reset input. This is the only difference from a standard counter. Drum Realize that the drum sequencer is its own process, and is a different programming method than stage programming. If you need to use a drum with stages, be sure to place the drum instruction in an ISG stage that is always active.
717
Using a Stage as a You may recall the light bulb on-off controller example from earlier in this Supervisory chapter. For the purpose of illustration, Toggle X0 Process suppose we want to monitor the productivity of the lamp process, by counting the number of on-off cycles which occurs. This application will require the addition of a simple counter, but the key decision is in where to put the counter.
Powerup
Ladder Program
Y0
ISG S0 Supervisor
OFF State
X0 S1 JMP
Supervisor Process
Powerup
X0
PushON
X0
SG S1 X0
PushOn State
S2 JMP
OFF
Main Process
ON
X0
SG S2 SP1
X0
PushOFF
ON State
Y0 OUT S3 JMP
New stage programming students will typically try to place the counter inside one the the stages of the process they are trying to monitor. The problem with this approach is that the stage is active only part of the time. In order for the counter to count, the count input must transition from off to on at least one scan after its stage activates. Ensuring this requires extra logic that can be tricky. In this case, we only need to add another supervisory stage as shown above, to watch the main process. The counter inside the supervisor stage uses the stage bit S1 of the main process as its count input. Stage bits used as a contact let us monitor a process! Note that both the Supervisor stage and the OFF stage are initial stages. The supervisor stage remains active indefinitely. Stage Counter
X0
SG S3 X0
PushOff State
S0 JMP
ISG S4 S1
Supervisor State
SGCNT K5000 CT0
The counter in the above example is a special Stage Counter. Note that it does not have a reset input. The count is reset by executing a Reset instruction, naming the counter bit (CT0 in this case). The Stage Counter has the benefit that its count may be globally reset from other stages. The standard Counter instruction does not have this global reset capability. You may still use a regular Counter instruction inside a stage... however, the reset input to the counter is the only way to reset it.
718
Our discussion of state transitions has shown how the Stage JMP instruction makes the current stage inactive and the next stage (named in the JMP) active. As an alternative way to enter this in DirectSOFT, you may use the power flow method for stage transitions. The main requirement is that the current stage be located directly above the next (jump-to) stage in the ladder program. This arrangement is shown in the diagram below, by stages S0 and S1, respectively. S0
X0
S1
SG S0 X0 S1 JMP
SG S0
Equivalent
SG S1
Recall that the Stage JMP instruction may occur anywhere in the current stage, and the result is the same. However, power flow transitions (shown above) must occur as the last rung in a stage. All other rungs in the stage will precede it. The power flow transition method is also achievable on the handheld programmer, by simply following the transition condition with the Stage instruction for the next stage. The power flow transition method does eliminate one Stage JMP instruction, its only advantage. However, it is not as easy to make program changes as using the Stage JMP. Therefore, we advise using Stage JMP transitions for most programmers. Stage View in DirectSOFT The Stage View option in DirectSOFT will let you view the ladder program as a flow chart. The figure below shows the symbol convention used in the diagrams. You may find the stage view useful as a tool to verify that your stage program has faithfully reproduced the logic of the state transition diagram you intend to realize.
Reference to a Stage Transition Logic J Jump S R Set Stage Reset Stage
SG
Stage
The following diagram is a typical stage view of a ladder program containing stages. Note the left-to-right direction of the flow chart.
ISG S0 SG S1 SG S2 SG S3 SG S4 SG S5
719
S3
SG S1 X0
PushOn State
S2 JMP
Process B
S4
S5
S4 JMP
Converging Processes
Note that if we want Stages S2 and S4 to energize exactly on the same scan, both stages must be located below or above Stage S1 in the ladder program (see the explanation at the bottom of page 77). Overall, parallel branching is easy! Now we consider the opposite case of parallel branching, which is converging processes. This simply means we stop doing multiple things and continue doing one thing at a time. In the figure below, processes A and B converge when stages S2 and S4 transition to S5 at some point in time. So, S2 and S4 are Convergence Stages.
Process A S1 S2 S5 Process B S3 S4 S6
= Convergence Stage
While the converging principle is simple enough, it brings a new complication. As parallel processing completes, the multiple processes almost never finish at the same time. In other words, how can we know whether Stage S2 or S4 will finish last? This is an important point, because we have to decide how to transition to Stage S5. The solution is to coordinate the transition condition out of convergence stages. We accomplish this with a stage type designed for this purpose: the Convergence Stage (type CV). In the example to the right, convergence stages S2 and S4 are required to be grouped together as shown. No logic is permitted between CV stages! The transition condition (X3 in this case) must be located in the last convergence stage. The transition condition only has power flow when all convergence stages in the group are active.
CV S2
Convergence Stages
CV S4 X3 S5 CVJMP
SG S5
720
Convergence Jump Recall the last convergence stage only has power flow when all CV stages in the (CVJMP) group are active. To complement the convergence stage, we need a new jump instruction. The Convergence Jump (CVJMP) shown to the right will transition to Stage S5 when X3 is active (as one might expect), but it also automatically resets all convergence stages in the group. This makes the CVJMP jump a very powerful instruction. Note that this instruction may only be used with convergence stages.
CV S2
Convergence Jump
CV S4 X3 S5 CVJMP
SG S5
The following summarizes the requirements in the use of convergence stages, including some tips for their effective application: S A convergence stage is to be used as the last stage of a process which is running in parallel to another process or processes. A transition to the convergence stage means that a particular process is through, and represents a waiting point until all other parallel processes also finish. The maximum number of convergence stages which make up one group is 16. In other words, a maximum of 16 stages can converge into one stage. Convergence stages of the same group must be placed together in the program, connected on the power rail without any other logic in between. Within a convergence group, the stages may occur in any order, top to bottom. It does not matter which stage is last in the group, because all convergence stages have to be active before the last stage has power flow. The last convergence stage of a group may have ladder logic within the stage. However, this logic will not execute until all convergence stages of the group are active. The convergence jump (CVJMP) is the intended method to be used to transition from the convergence group of stages to the next stage. The CVJMP resets all convergence stages of the group, and energizes the stage named in the jump. The CVJMP instruction must only be used in a convergence stage, as it is invalid in regular or initial stages. Convergence Stages or CVJMP instructions may not be used in subroutines or interrupt routines.
S S S
S S
S S
721
SG S aaa
The following example is a simple RLL PLUS program. This program utilizes an initial stage, stage, and jump instructions to create a structured program.
DirectSOFT
ISG S0
Handheld Programmer Keystrokes U ISG $ STR X0 Y0 OUT X1 S2 SET X5 S1 JMP K JMP 2 SG B 1 B 1 C STR GX OUT X2 Y1 OUT $ STR GX OUT $ STR X6 V AND K JMP 2 SG G 6 C 2 H 7 SHFT A 0 B 1 C 2 2 ENT ENT ENT ENT ENT ENT ENT ENT S RST ENT B 1 ENT GX OUT $ STR X SET $ STR A 0 B 1 SHFT F 5 A 0 A 0 ENT ENT ENT ENT S RST ENT C 2 ENT
SG
S1
SG
S2
Y2 OUT
X7
S1
S0 JMP
722
The Initial Staget instruction is normally used as the first segment of an RLL PLUS program. Multiple Initial Stages are allowed in a program. They will be active when the CPU enters the Run mode allowing for a starting point in the program.
Operand Data Type DL05 Range aaa Stage S 0377
ISG S aaa
Initial Stages are also activated by transitional logic, a jump or a set stage executed from an active stage. JUMP (JMP) The Jump instruction allows the program to transition from an active stage containing the jump instruction to another stage (specified in the instruction). The jump occurs when the input logic is true. The active stage containing the Jump will deactivate 1 scan later.
Operand Data Type DL05 Range aaa Stage S 0377
S aaa JMP
The Not Jump instruction allows the program to transition from an active stage which contains the jump instruction to another which is specified in the instruction. The jump will occur when the input logic is off. The active stage that contains the Not Jump will be deactivated 1 scan after the Not Jump instruction is executed.
Operand Data Type DL05 Range aaa Stage S 0377
S aaa NJMP
In the following example, only stage ISG0 will be active when program execution. begins. When X1 is on, program execution will jump from Initial Stage 0 to Stage 1.
723
DirectSOFT
ISG S0
Handheld Programmer Keystrokes U ISG $ X1 S1 JMP STR K JMP 2 SG $ X2 Y5 OUT S2 JMP S3 NJMP S S S STR GX OUT $ STR K JMP SHFT N TMR C 2 SHFT F 5 H 7 C 2 B 1 B 1 B 1 A 0 ENT ENT ENT ENT ENT ENT ENT ENT K JMP D 3 ENT
SG
S1
X7
X7
Converge Stage The Converge Stage instruction is used to (CV) and Converge group certain stages together by defining them as Converge Stages. Jump (CVJMP) When all of the Converge Stages within a group become active, the CVJMP instruction (and any additional logic in the final CV stage) will be executed. All preceding CV stages must be active before the final CV stage logic can be executed. All Converge Stages are deactivated one scan after the CVJMP instruction is executed. Additional logic instructions are only allowed following the last Converge Stage instruction and before the CVJMP instruction. Multiple CVJUMP instructions are allowed. Converge Stages must be programmed in the main body of the application program. This means they cannot be programmed in Subroutines or Interrupt Routines.
Operand Data Type DL05 Range aaa Stage S 0377
CV S aaa
S aaa CVJMP
724
In the following example, when Converge Stages S10 and S11 are both active the CVJMP instruction will be executed when X4 is on. The CVJMP will deactivate S10 and S11, and activate S20. Then, if X5 is on, the program execution will jump back to the initial stage, S0.
DirectSOFT Display
Handheld Programmer Keystrokes U ISG $ STR A 0 A 0 B STR K JMP K JMP 2 SG $ STR K JMP SHFT SHFT C 2 C 2 B 1 V AND V AND D STR GX OUT D 3 E STR SHFT C 2 4 V AND C SG 2 F STR K JMP A 0 5 3 ENT ENT ENT SHFT A 0 ENT ENT K JMP ENT C 2 A 0 ENT C 2 B 1 B 1 B 1 1 A 0 ENT ENT ENT ENT ENT A 0 ENT ENT B 1 ENT B 1 B 1 B 1 A 0 ENT ENT ENT
ISG
S0
GX OUT
X0
X1
SG
S1
X2
S11 JMP
CV
S10
CV
S11
2 $
X3
X4
SG
S20
X5
S0 JMP
725
726
Q. Isnt a Stage JMP just like a regular GOTO instruction used in software? A. No, it is very different. A GOTO instruction sends the program execution immediately to the code location named by the GOTO. A Stage JMP simply resets the Stage Bit of the current stage, while setting the Stage Bit of the stage named in the JMP instruction. Stage bits are 0 or 1, determining the inactive/active status of the corresponding stages. A stage JMP has the following results: S When the JMP is executed, the remainder of the current stages rungs are executed, even if they reside past(under) the JMP instruction. On the following scan, that stage is not executed, because it is inactive. S The Stage named in the Stage JMP instruction will be executed upon its next occurrence. If located past (under) the current stage, it will be executed on the same scan. If located before (above) the current stage, it will be executed on the following scan. Q. How can I know when to use stage JMP, versus a Set Stage Bit or Reset Stage Bit? A. These instructions are used according to the state diagram topology you have derived: S Use a Stage JMP instruction for a state transition... moving from one state to another. S Use a Set Stage Bit instruction when the current state is spawning a new parallel state or stage sequence, or when a supervisory state is starting a state sequence under its command. S Use a Reset Bit instruction when the current state is the last state in a sequence and its task is complete, or when a supervisory state is ending a state sequence under its command. Q. What is an initial stage, and when do I use it? A. An initial stage (ISG) is automatically active at powerup. Afterwards, it works just like any other stage. You can have multiple initial stages, if required. Use an initial stage for ladder that must always be active, or as a starting point. Q. Can I have place program ladder rungs outside of the stages, so they are always on? A. It is possible, but its not good software design practice. Place ladder that must always be active in an initial stage, and do not reset that stage or use a Stage JMP instruction inside it. It can start other stage sequences at the proper time by setting the appropriate Stage Bit(s). Q. Can I have more than one active stage at a time? A. Yes, and this is a normal occurrence for many programs. However, it is important to organize your application into separate processes, each made up of stages. And a good process design will be mostly sequential, with only one stage on at a time. However, all the processes in the program may be active simultaneously.
18
Hardware System Maintenance Diagnostics CPU Indicators Communications Problems I/O Point Troubleshooting Noise Troubleshooting Machine Startup and Program Troubleshooting
82
Diagnostics
Diagnostics Maintenabce and Troubleshooting Your DL05 Micro PLC performs many pre-defined diagnostic routines with every CPU scan. The diagnostics can detect various errors or failures in the PLC. The two primary error classes are fatal and non-fatal. Fatal errors are errors which may cause the system to function improperly, perhaps introducing a safety problem. The CPU will automatically switch to Program Mode if it is in Run Mode. (Remember, in Program Mode all outputs are turned off.) If the fatal error is detected while the CPU is in Program Mode, the CPU will not allow you to transition to Run Mode until the error has been corrected. Some examples of fatal errors are: S Power supply failure S Parity error or CPU malfunction S Particular programming errors Non-fatal errors are errors that need your attention, but should not cause improper operation. They do not cause or prevent any mode transitions of the CPU. The application program can use special relay contacts to detect non-fatal errors, and even take the system to an orderly shutdown or switch the CPU to Program Mode if desired. An example of a non-fatal error is: S Particular programming errors
Fatal Errors
Non-fatal Errors
Finding Diagnostic The programming devices will notify you of an error if one occurs while online. Information S Direct SOFT provides the error number and an error message. S The handheld programmer displays error numbers and short descriptions of the error. Appendix B has a complete list of error messages in order by error number. Many error messages point to supplemental V-memory locations which contain related information. Special relays (SP contacts) also provide error indications.
83
The following table names the specific memory locations that correspond to certain types of error messages.
Error Class User-Defined System Error Error Category Error code used with FAULT instruction Fatal Error code Major Error code Minor Error code Grammatical Address where syntax error occurs Diagnostic V-memory V7751 V7755 V7756 V7757 V7763
Error Code found during syntax check V7764 CPU Scan Number of scans since last Program to Run Mode transition Current scan time (ms) Minimum scan time (ms) Maximum scan time (ms) V7765 V7775 V7776 V7777
Special Relays (SP) The special relay table also includes status indicators which can indicate errors. For Corresponding to a more detailed description of each of these special relays refer to Appendix D. Error Codes
CPU Status Relays SP11 SP12 SP13 SP15 SP16 SP17 SP20 SP22 SP36 SP37 SP40 SP41 SP42 SP44 SP45 SP46 SP50 SP51 Forced Run mode Terminal Run mode Test Run mode Test stop mode Terminal Program mode Forced stop STOP instruction was executed Interrupt enabled Override setup Scan control error Critical error Non-critical error Diagnostics error Program memory error I/O error Communications error Fault instruction was executed Watchdog timeout SP52 SP53 SP54 SP56 Syntax error Cannot solve the logic Communication error Table instruction overrun
Accumulator Status Relays SP60 SP61 SP62 SP63 SP64 SP65 SP66 SP67 SP70 SP71 SP73 SP75 SP76 Acc. is less than value Acc. is equal to value Acc. is greater than value Acc. result is zero Half borrow occurred Borrow occurred Half carry occurred Carry occurred Result is negative (sign) Pointer reference error Overflow Data is not in BCD Load zero
84
These errors can be generated by the CPU or by the Handheld Programmer, depending on the actual error. Appendix B provides a more complete description of the error codes. The errors can be detected at various times. However, most of them are detected at power-up, on entry to Run Mode, or when a Handheld Programmer key sequence results in an error or an illegal request.
Error Code E525 E526 E527 E528 E540 E541 E542 E601 E602 E604 E620 E621 E622 E624 E625 E627 E628 E640 E650 E651 E652 Description Mode Switch not in Term position Unit is offline Unit is online CPU mode CPU locked Wrong password Password reset Memory full Instruction missing Reference missing Out of memory EEPROM Memory not blank No Handheld Programmer EEPROM V memory only Program only Bad write operation Memory type error (should be EEPROM) Mis-compare Handheld Programmer system error Handheld Programmer ROM error Handheld Programmer RAM error
Error Code E003 E004 E104 E151 E311 E312 E313 E316
Description Software time-out Invalid instruction (RAM parity error in the CPU) Write failed Invalid command Communications error 1 Communications error 2 Communications error 3 Communications error 6 Time out Communications error HP Peripheral port time-out Bad entry Bad address Bad command Bad reference / value Invalid instruction Invalid operation Bad operation CPU in Run Bad operation CPU in Test Run Bad operation CPU in Test Program Bad operation CPU in Program
85
The following table lists program syntax and runtime error codes. Error detection occurs during a Program-to-Run mode transition, or when you use AUX 21 Check Program. The CPU will also turn on SP52 and store the error code in V7755. Appendix B provides a more complete description of the error codes.
Description Error Code E438 E440 E441 E451 E453 E454 E455 E456 E461 E462 E463 E464 E471 E472 E473 E499 Description Invalid IRT address Invalid Data Address ACON/NCON Bad MLS/MLR Missing T/C Bad TMRA Bad CNT Bad SR Stack Overflow Stack Underflow Logic Error
Error Code E4** E401 E402 E403 E404 E405 E406 E412 E421 E422 E423 E431 E433 E434 E435 E436 E437
No Program in CPU Missing END statement Missing LBL HP Peripheral port time-out HP Peripheral port time-out HP Peripheral port time-out Missing IRT SBR / LBL >64 Duplicate stage reference Duplicate SBR/LBL reference HP Peripheral port time-out Invalid ISG/SG address Invalid ISG / SG address Invalid RTC Invalid RT Invalid INT address Invalid IRTC
Missing Circuit Duplicate coil reference Duplicate TMR reference Duplicate CNT reference Print instruction
86
CPU Indicators
The DL05 Micro PLCs have indicators on the front to help you determine potential problems with the system. In normal runtime operation only, the RUN and PWR indicators are on. The table below is a quick reference to potential problems. Indicator Status Potential Problems PWR (LED off) 1. System voltage incorrect 2. PLC power supply faulty RUN (LED off) 1. CPU programming error 2. (CPU in program mode) CPU (LED on) 1. Electrical noise interference 2. Internal CPU defective
PWR Indicator
In general there are three reasons for the CPU power status LED (PWR) to be OFF: 1. Power to the unit is incorrect or is not applied. 2. PLC power supply is faulty. 3. Other component(s) have the power supply shut down. If the voltage to the power supply is not correct, the PLC may not operate properly or may not operate at all. Use the following guidelines to correct the problem. WARNING: To minimize the risk of electrical shock, always disconnect the system power before inspecting the physical wiring. 1. First, disconnect the external power. 2. Verify that all external circuit breakers or fuses are still intact. 3. Check all incoming wiring for loose connections. If youre using a separate termination block, check those connections for accuracy and integrity. 4. If the connections are acceptable, reconnect the system power and verify the voltage at the DL05 power input is within specification. If the voltage is not correct shut down the system and correct the problem. 5. If all wiring is connected correctly and the incoming power is within the specifications, the PLC internal supply may be faulty. The best way to check for a faulty PLC is to substitute a known good one to see if this corrects the problem. The removable connectors on the DL05 make this relatively easy. If there has been a major power surge, it is possible the PLC internal power supply has been damaged. If you suspect this is the cause of the power supply damage, consider installing an AC line conditioner to attenuate damaging voltage spikes in the future.
87
RUN Indicator
If the CPU will not enter the Run mode (the RUN indicator is off), the problem is usually in the application program, unless the CPU has a fatal error. If a fatal error has occurred, the CPU LED should be on. (You can use a programming device to determine the cause of the error.) Both of the programming devices, Handheld Programmer and Direct SOFT, will return an error message describing the problem. Depending on the error, there may also be an AUX function you can use to help diagnose the problem. The most common programming error is Missing END Statement. All application programs require an END statement for proper termination. A complete list of error codes can be found in Appendix B. If the CPU indicator is on, a fatal error has occurred in the CPU. Generally, this is not a programming problem but an actual hardware failure. You can power cycle the system to clear the error. If the error clears, you should monitor the system and determine what caused the problem. You will find this problem is sometimes caused by high frequency electrical noise introduced into the CPU from an outside source. Check your system grounding and install electrical noise filters if the grounding is suspected. If power cycling the system does not reset the error, or if the problem returns, you should replace the CPU.
CPU Indicator
Communications Problems
If you cannot establish communications with the CPU, check these items. S S S S S S S S The cable is disconnected. The cable has a broken wire or has been wired incorrectly. The cable is improperly terminated or grounded. The device connected is not operating at the correct baud rate (9600 baud). The device connected to the port is sending data incorrectly. A grounding difference exists between the two devices. Electrical noise is causing intermittent errors. The PLC has a bad communication port and should be replaced.
For problems in communicating with DirectSOFT on a personal computer, refer to the DirectSOFT manual. It includes a troubleshooting section that can help you diagnose PC problems in communications port setup, address or interrupt conflicts, etc.
88
89
Output points can be set on or off in the DL05 series CPUs. If you want to do an I/O check out independent of the application program, follow the procedure below: Step 1 2 3 4 5 6 7 Action Use a handheld programmer or Direct SOFT to communicate online to the PLC. Change to Program Mode. Go to address 0. Insert an END statement at address 0. (This will cause program execution to occur only at address 0 and prevent the application program from turning the I/O points on or off). Change to Run Mode. Use the programming device to set (turn) on or off the points you wish to test. When you finish testing I/O points delete the END statement at address 0.
WARNING: Depending on your application, forcing I/O points may cause unpredictable machine operation that can result in a risk of personal injury or equipment damage. Make sure you have taken all appropriate safety precautions prior to testing any I/O points. Handheld Programmer Keystrokes Used to Test an Output Point
END
X0 X1
X2 X3 X4
X5
X7
Y2
Insert an END statement at the beginning of the program. This disables the remainder of the program.
END
10
Use arrow keys to select point, then use ON and OFF to change the status
SHFT ON INS
Y2 is now on
10
810
Noise Troubleshooting
Electrical Noise Problems Noise is one of the most difficult problems to diagnose. Electrical noise can enter a system in many different ways and they fall into one of two categories, conducted or radiated. It may be difficult to determine how the noise is entering the system but the corrective actions for either of the types of noise problems are similar. S Conducted noise is when the electrical interference is introduced into the system by way of a attached wire, panel connection ,etc. It may enter through an I/O circuit, a power supply connection, the communication ground connection, or the chassis ground connection. S Radiated noise is when the electrical interference is introduced into the system without a direct electrical connection, much in the same manner as radio waves. While electrical noise cannot be eliminated it can be reduced to a level that will not affect the system. S Most noise problems result from improper grounding of the system. A good earth ground can be the single most effective way to correct noise problems. If a ground is not available, install a ground rod as close to the system as possible. Ensure all ground wires are single point grounds and are not daisy chained from one device to another. Ground metal enclosures around the system. A loose wire can act as a large antenna, introducing noise into the system. Therefore, tighten all connections in your system. Loose ground wires are more susceptible to noise than the other wires in your system. Review Chapter 2 Installation, Wiring, and Specifications if you have questions regarding how to ground your system. S Electrical noise can enter the system through the power source for the PLC and I/O circuits. Installing an isolation transformer for all AC sources can correct this problem. DC sources should be well-grounded good quality supplies. S Separate input wiring from output wiring. Never run low-voltage I/O wiring close to high voltage wiring.
811
(You may not get the busy display if the program is not very long.)
BUSY
Maintenance and Troubleshooting
Syntax OK display
NO SYNTAX ERROR ?
See the Error Codes Section for a complete listing of programming error codes. If you get an error, just press CLR and the Handheld will display the instruction where the error occurred. Correct the problem and continue running the Syntax check until the NO SYNTAX ERROR message appears.
812
Special Instructions
There are several instructions that can be used to help you debug your program during machine startup operations. S END S PAUSE S STOP END Instruction: If you need a way to quickly disable part of the program, just insert an END statement prior to the portion that should be disabled. When the CPU encounters the END statement, it assumes that is the end of the program. The following diagram shows an example.
Normal Program X0 X1 X10 X2 X3 X4 Y1
END
X10
END
Y1
END
PAUSE Instruction: This instruction provides a quick way to allow the inputs (or other logic) to operate while disabling selected outputs. The output image register is still updated, but the output circuits are not. For example, you could make this conditional by adding an input contact or CR to control the instruction with a switch or a programming device. Or, you could just add the instruction without any conditions so the selected outputs would be disabled at all times.
Normal Program PAUSE disables Y0 and Y1 Y0 X4 Y1 X0 X1 X10
END Y0 Y1 PAUSE
X0 X1 X10
X2 X3
X2 X3 X4
Y0
Y1
END
STOP Instruction: Sometimes during machine startup you need a way to quickly turn off all the outputs and return to Program Mode. You can use the STOP instruction. When this instruction is executed the CPU automatically exits Run Mode and enters Program Mode. Remember, all outputs are turned off during Program Mode. The following diagram shows an example of a condition that returns the CPU to Program Mode.
813
Normal Program X0 X1 X5 X2 X3 X4 Y1 Y0
X0 X1 X5
END
X2 X3 X4
Y0
Y1
END
In the example shown above, you could trigger X10 which would execute the STOP instruction. The CPU would enter Program Mode and all outputs would be turned off. You can also check for multiple uses of the same output coil. Both programming devices offer a way to check for this condition.. For example, you can AUX 21, CHECK PROGRAM to check for duplicate references from a Handheld Programmer, or you can use the PLC Diagnostics menu option within DirectSOFT. The following example shows how to perform the duplicate reference check with a Handheld Programmer. Use AUX 21 to perform syntax check
CLR C 2 B 1 AUX ENT
(You may not get the busy display if the program is not very long.)
BUSY
Maintenance and Troubleshooting
One of two displays will appear Error Display (example) (shows location in question)
Syntax OK display
NO DUP REFS ?
If you get an error, just press CLR and the Handheld will display the instruction where the error occurred. Correct the problem and continue running the Duplicate Reference check until no duplicate references are found. NOTE: You can use the same coil in more than one location, especially in programs containing Stage instructions and / or OROUT instructions. The Duplicate Reference check will find occurrences, even though they are acceptable.
814
The DL05 Micro PLC allows you to make changes to the application program during Run Mode. These edits are not bumpless. Instead, CPU scan is momentarily interrupted (and the outputs are maintained in their current state) until the program change is complete. This means if the output is off, it will remain off until the program change is complete. If the output is on, it will remain on. WARNING: Only authorized personnel fully familiar with all aspects of the application should make changes to the program. Changes during Run Mode become effective immediately. Make sure you thoroughly consider the impact of any changes to minimize the risk of personal injury or damage to equipment. There are some important operational changes during Run Time Edits. 1. If there is a syntax error in the new instruction, the CPU will not enter the Run Mode. 2. If you delete an output coil reference and the output was on at the time, the output will remain on until it is forced off with a programming device. 3. Input point changes are not acknowledged during Run Time Edits. So, if youre using a high-speed operation and a critical input comes on, the CPU may not see the change. Not all instructions can be edited during a Run Time Edit session. The following list shows the instructions that can be edited.
Mnemonic TMR TMRF TMRA TMRAF CNT UDC SGCNT STR, STRN AND, ANDN OR, ORN STRE, STRNE ANDE, ANDNE ORE, ORNE STR, STRN AND, ANDN
Description Timer Fast timer Accumulating timer Accumulating fast timer Counter Up / Down counter Stage counter Store, Store not And, And not Or, Or not Store equal, Store not equal And equal, And not equal Or equal, Or not equal Store greater than or equal Store less than And greater than or equal And less than
Mnemonic OR, ORN LD LDD ADDD SUBD MUL DIV CMPD ANDD ORD XORD LDF OUTF SHFR SHFL NCON
Description Or greater than or equal Or less than Load data (constant) Load data double (constant) Add data double (constant) Subtract data double (constant) Multiply (constant) Divide (constant) Compare accumulator (constant) And accumulator (constant) Or accumulator (constant) Exclusive or accumulator (constant) Load discrete points to accumulator Output accumulator to discrete points Shift accumulator right Shift accumulator left Numeric constant
815
Well use the program logic shown to describe how this process works. In the example, well change X0 to C10. Note, the example assumes you have already placed the CPU in Run Mode.
X0
X1
Y0 OUT
C0
(Note, the RUN LED on the D2HPP Handheld starts flashing to indicate Run Time Edits are enabled.)
Find the instruction you want to change (X0) Maintenance and Troubleshooting
SHFT X SET A 0 SHFT FD REF FIND
$00000 STR X0
Press the arrow key to move to the X. Then enter the new contact (C10).
SHFT C 2 B 1 A 0 ENT
OR C0
816
There are many times, especially during machine startup and troubleshooting, that you need the capability to force an I/O point to be either on or off. Before you use a programming device to force any data type it is important you understand how the DL05 CPUs process the forcing requests. WARNING: Only authorized personnel fully familiar with the application should make program changes. Do thoroughly consider the impact of any changes to minimize the risk of personal injury or damage to equipment. Bit Forcing Bit forcing temporarily changes the status of a discrete bit. For example, you may want to force an input on even though the program has turned it off. This allows you to change the point status stored in the image register. The forced value will be valid until the CPU writes to the image register location during the next scan. This is useful you just need to force a bit on to trigger another event. The following diagrams show a brief example of how you could use the D2HPP Handheld Programmer to force an I/O point. The example assumes you have already placed the CPU into Run Mode.
X0 Y0 OUT
C0
Use the PREV or NEXT keys to select the Y data type. (Once the Y appears, press 0 to start at Y0.)
NEXT A 0 ENT
10
Use arrow keys to select point, then use ON and OFF to change the status
SHFT ON INS
Y2 is now on
10
BIT FORCE Y7
No fill indicates point is off.
BIT FORCE Y7
Auxiliary Functions
1A
In This Appendix. . . .
Introduction AUX 2* RLL Operations AUX 3* Vmemory Operations AUX 4* I/O Configuration AUX 5* CPU Configuration AUX 6* Handheld Programmer Configuration AUX 7* EEPROM Operations AUX 8* Password Operations
A2
Appendix A Auxiliary Functions
Auxiliary Functions
Introduction
Many CPU setup tasks involve the use of Auxiliary (AUX) Functions. The AUX Purpose of Auxiliary Functions Functions perform many different operations, including clearing ladder memory, displaying the scan time, and copying programs to EEPROM in the handheld programmer. They are divided into categories that affect different system resources. You can access the AUX Functions from Direct SOFT or from the D2HPP Handheld Programmer. The manuals for those products provide step-by-step procedures for accessing the AUX Functions. Some of these AUX Functions are designed specifically for the Handheld Programmer setup, so they will not be needed (or available) with the Direct SOFT package. Even though this Appendix provides many examples of how the AUX functions operate, you should supplement this information with the documentation for your choice of programming device. Note, the Handheld Programmer may have additional AUX functions that are not supported with the DL05 PLCs.
AUX Function and Description AUX 2* RLL Operations 21 22 23 24 31 41 51 53 54 55 56 57 58 59 5B 5D m Check Program Change Reference Clear Ladder Range Clear All Ladders Clear V Memory Show I/O Configuration Modify Program Name Display Scan Time Initialize Scratchpad Set Watchdog Timer Set Communication Port 2 Set Retentive Ranges Test Operations Override Setup HSIO Interface Configuration Scan Control Setup m m m m m m m m m m m m m m m m DL05 AUX Function and Description DL05
AUX 6* Handheld Programmer Configuration 61 62 65 71 72 73 74 75 76 Show Revision Numbers Beeper On / Off Run Self Diagnostics Copy CPU memory to HPP EEPROM Write HPP EEPROM to CPU Compare CPU to HPP EEPROM Blank Check (HPP EEPROM) Erase HPP EEPROM Show EEPROM Type (CPU and HPP) Modify Password Unlock CPU Lock CPU m HP HP HP HP HP HP HP HP
Auxilliary Functions
A3
Appendix A Auxiliary Functions
Direct SOFT provides various menu options during both online and offline programming. Some of the AUX functions are only available during online programming, some only during offline programming, and some during both online and offline programming. The following diagram shows and example of the PLC operations menu available within Direct SOFT.
Menu Options
You can also access the AUX functions by using a Handheld Programmer. Plus, remember some of the AUX functions are only available from the Handheld. Sometimes the AUX name or description cannot fit on one display. If you want to see the complete description, just press the arrow keys to scroll left and right. Also, depending on the current display, you may have to press CLR more than once.
CLR AUX
You can also enter the exact AUX number to go straight to the sub-menu. Enter the AUX number directly
D 3 B 1
CLR
AUX
A4
Appendix A Auxiliary Functions
Auxiliary Functions
Auxilliary Functions
A5
Appendix A Auxiliary Functions
AUX 53 displays the current, minimum, and maximum scan times. The minimum AUX 53 Display Scan Time and maximum times are the ones that have occurred since the last Program Mode to Run Mode transition. You can also perform this operation from within Direct SOFT by using the PLC/Diagnostics sub-menu. AUX 54 Initialize Scratchpad The CPU maintains system parameters in a memory area often referred to as the scratchpad. In some cases, you may make changes to the system setup that will be stored in system memory. For example, if you specify a range of Control Relays (CRs) as retentive, these changes are stored. NOTE: You may never have to use this feature unless you have made changes that affect system memory. Usually, youll only need to initialize the system memory if you are changing programs and the old program required a special system setup. You can usually change from program to program without ever initializing system memory. AUX 54 resets the system memory to the default values. You can also perform this operation from within Direct SOFT by using the PLC/Setup sub-menu. AUX 55 Set Watchdog Timer DL05 PLCs have a watchdog timer that is used to monitor the scan time. The default value set from the factory is 200 ms. If the scan time exceeds the watchdog time limit, the CPU automatically leaves RUN mode and enters PGM mode. The Handheld displays the following message E003 S/W TIMEOUT when the scan overrun occurs. Use AUX 55 to increase or decrease the watchdog timer value. You can also perform this operation from within Direct SOFT by using the PLC/Setup sub-menu. Since the DL05 CPU has an additional communication port, you can use the Handheld to set the network address for port 2 and the port communication parameters. The default settings are: S Station address 1 S HEX mode S Odd parity You can use this port with either the Handheld Programmer, Direct SOFT, or, as a communication port for DirectNET and MODBUS. Refer to Direct NET and MODBUS manuals for additional information about communication settings required for network operation.
A6
Appendix A Auxiliary Functions
Auxiliary Functions
NOTE: You will only need to use this procedure if you have port 2 connected to a network. Otherwise, the default settings will work fine. Use AUX 56 to set the network address and communication parameters. You can also perform this operation from within Direct SOFT by using the PLC/Setup sub-menu. AUX 57 Set Retentive Ranges DL05 CPUs provide certain ranges of retentive memory by default. Some of the retentive memory locations are backed up by a super-capacitor, and others are in non-volatile FLASH memory. The FLASH memory locations are V7400 to V7577. The default ranges are suitable for many applications, but you can change them if your application requires additional retentive ranges or no retentive ranges at all. The default settings are:
DL05 Memory Area Control Relays V Memory Timers Counters Stages Default Range C400 C777 V1400 V7777 CT0 CT177 Available Range C0 C777 V0 V7777 CT0 CT177
Use AUX 57 to change the retentive ranges. You can also perform this operation from within Direct SOFT by using the PLC/Setup sub-menu. WARNING: The DL05 CPUs do not have battery-backed RAM. The super-capacitor will retain the values in the event of a power loss, but only up to 3 weeks. (The retention time may be as short as 4 1/2 days in 60 degree C operating temperature.) AUX 58 Test Operations AUX 59 Bit Override AUX 58 is used to override the output disable function of the Pause instruction. Use AUX 58 to program a single output or a range of outputs which will operate normally even when those points are within the scope of the pause instruction. Bit override can be enabled on a point-by-point basis by using AUX 59 from the Handheld Programmer or, by a menu option from within Direct SOFT. Bit override basically disables any changes to the discrete point by the CPU. For example, if you enable bit override for X1, and X1 is off at the time, then the CPU will not change the state of X1. This means that even if X1 comes on, the CPU will not acknowledge the change. So, if you used X1 in the program, it would always be evaluated as off in this case. Of course, if X1 was on when the bit override was enabled, then X1 would always be evaluated as on. There is an advantage available when you use the bit override feature. The regular forcing is not disabled because the bit override is enabled. For example, if you enabled the Bit Override for Y0 and it was off at the time, then the CPU would not change the state of Y0. However, you can still use a programming device to change the status. Now, if you use the programming device to force Y0 on, it will remain on and the CPU will not change the state of Y0. If you then force Y0 off, the CPU will maintain Y0 as off. The CPU will never update the point with the results from the application program or from the I/O update until the bit override is removed from the point.
Auxilliary Functions
A7
Appendix A Auxiliary Functions
The following diagram shows a brief overview of the bit override feature. Notice the CPU does not update the Image Register when bit override is enabled.
Bit Override OFF
Input Update Force from Programmer Result of Program Solution
X128 OFF Y128 OFF C377 OFF ... ... ... ... ... ... X2 ON Y2 ON C2 ON X1 ON Y1 ON C1 OFF X0 OFF Y0 OFF C0 OFF
Bit Override ON
Input Update Force from Programmer Result of Program Solution
AUX 5B is used with the High-Speed I/O (HSIO) function to select the configuration. You can choose the type of counter, set the counter parameters, etc. See Chapter 3 for a complete description of how to select the various counter features. The DL05 CPU has two program scan modes: fixed and variable. In fixed mode, the scan time is lengthened to the time you specify (in milliseconds). If the actual scan time is longer than the fixed scan time, then the error code E504 BAD REF/VAL is displayed. In variable scan mode, the CPU begins each scan as soon as the previous scans activities complete.
A8
Appendix A Auxiliary Functions
Auxiliary Functions
AUX 71 copies information from the CPU memory to an EEPROM installed in the Handheld Programmer.You can copy different portions of EEPROM (HP) memory to the CPU memory as shown in the previous table.
Auxilliary Functions
A9
Appendix A Auxiliary Functions
AUX 72 copies information from the EEPROM installed in the Handheld Programmer to CPU memory in the DL05. You can copy different portions of EEPROM (HP) memory to the CPU memory as shown in the previous table.
AUX 73 Compare HPP EEPROM to CPU AUX 74 HPP EEPROM Blank Check
AUX 73 compares the program in the Handheld programmer (EEPROM) with the CPU program. You can compare different types of information as shown previously.
AUX 74 allows you to check the EEPROM in the handheld programmer to make sure it is blank. Its a good idea to use this function anytime you start to copy an entire program to an EEPROM in the handheld programmer.
AUX 75 allows you to clear all data in the EEPROM in the handheld programmer. You should use this AUX function before you copy a program from the CPU.
You can use AUX 76 to quickly determine what size EEPROM is installed in the Handheld Programmer.
A10
Appendix A Auxiliary Functions
Auxiliary Functions You can also enter or modify a password from within Direct SOFT by using the PLC/Password sub-menu. This feature works slightly differently in Direct SOFT. Once youve entered a password, the CPU is automatically locked when you exit the software package. It will also be locked if the CPU is power cycled. WARNING: Make sure you remember the password before you lock the CPU. Once the CPU is locked you cannot view, change, or erase the password. If you do not remember the password, you have to return the CPU to the factory for password removal.
AUX 82 can be used to unlock a CPU that has been password protected. Direct SOFT will automatically ask you to enter the password if you attempt to communicate with a CPU that contains a password. AUX 83 can be used to lock a CPU that contains a password. Once the CPU is locked, you will have to enter a password to gain access. Remember, this is not necessary with Direct SOFT since the CPU is automatically locked whenever you exit the software package.
1B
In This Appendix. . . .
Error Code Table
B2
DL05 Error Code E003 SOFTWARE TIME-OUT E004 INVALID INSTRUCTION Appendix B Error Codes E104 WRITE FAILED
Description If the program scan time exceeds the time allotted to the watchdog timer, this error will occur. SP51 will be on and the error code will be stored in V7755. To correct this problem use AUX 55 to extend the time allotted to the watchdog timer. The CPU attempted to execute an instruction code, but the RAM contents had a parity error. Performing a program download to the CPU in an electrically noisy environment can corrupt a programs contents. Clear the CPU program memory, and download the program again. A write to the CPU was not successful. Disconnect the power, remove the CPU, and make sure the EEPROM is not write protected. If the EEPROM is not write protected, make sure the EEPROM is installed correctly. If both conditions are OK, replace the CPU. A parity error has occurred in the application program. SP44 will be on and the error code will be stored in V7755 .This problem may possibly be due to electrical noise. Clear the memory and download the program again. Correct any grounding problems. If the error returns replace the Micro PLC. A request from the handheld programmer could not be processed by the CPU. Clear the error and retry the request. If the error continues replace the CPU. SP46 will be on and the error code will be stored in V7756. A data error was encountered during communications with the CPU. Clear the error and retry the request. If the error continues check the cabling between the two devices, replace the handheld programmer, then if necessary replace the CPU. The error code will be stored in V7756. An address error was encountered during communications with the CPU. Clear the error and retry the request. If the error continues check the cabling between the two devices, replace the handheld programmer, then if necessary replace the CPU. The error code will be stored in V7756. A mode error was encountered during communications with the CPU. Clear the error and retry the request. If the error continues replace the handheld programmer, then if necessary replace the CPU. The error code will be stored in V7756. The CPU did not respond to the handheld programmer communication request. Check to insure cabling is correct and not defective. Power cycle the system if the error continues replace the CPU first and then the handheld programmer if necessary. A data error was encountered during communication with the CPU. Check to insure cabling is correct and not defective. Power cycle the system and if the error continues replace the CPU first and then the handheld programmer if necessary. The device connected to the peripheral port did not respond to the handheld programmer communication request. Check to insure cabling is correct and not defective. The peripheral device or handheld programmer could be defective.
E311 HP COMM ERROR 1 E312 HP COMM ERROR 2 E313 HP COMM ERROR 3 E316 HP COMM ERROR 6 E320 HP COMM TIME-OUT E321 COMM ERROR
B3
Appendix A DL405 Error Codes
Description A syntax error exists in the application program. The most common is a missing END statement. Run AUX21 to determine which one of the E4** series of errors is being flagged. SP52 will be on and the error code will be stored in V7755. All application programs must terminate with an END statement. Enter the END statement in appropriate location in your program. SP52 will be on and the error code will be stored in V7755. A MOVMC or LDLBL instruction was used without the appropriate label. Refer to the Chapter 5 for details on these instructions. SP52 will be on and the error code will be stored in V7755. A subroutine in the program does not end with the RET instruction. SP52 will be on and the error code will be stored in V7755. A NEXT instruction does not have the corresponding FOR instruction. SP52 will be on and the error code will be stored in V7755. A FOR instruction does not have the corresponding NEXT instruction. SP52 will be on and the error code will be stored in V7755. An interrupt routine in the program does not end with the IRT instruction. SP52 will be on and the error code will be stored in V7755. There is greater than 64 SBR or DLBL instructions in the program. This error is also returned if there is greater than 2 INT instructions used in the program. SP52 will be on and the error code will be stored in V7755. Two or more SG or ISG labels exist in the application program with the same number. A unique number must be allowed for each Stage and Initial Stage. SP52 will be on and the error code will be stored in V7755. Two or more LBL instructions exist in the application program with the same number. A unique number must be allowed for each and label. SP52 will be on and the error code will be stored in V7755. Nested loops (programming one FOR/NEXT loop inside of another) are not allowed. SP52 will be on and the error code will be stored in V7755. An ISG or SG instruction must not be placed after the end statement (such as inside a subroutine). SP52 will be on and the error code will be stored in V7755.
E401 MISSING END STATEMENT E402 MISSING LBL E403 MISSING RET E404 MISSING FOR E405 MISSING NEXT E406 MISSING IRT E412 SBR/LBL>64 E421 DUPLICATE STAGE REFERENCE E422 DUPLICATE LBL REFERENCE E423 NESTED LOOPS E431 INVALID ISG/SG ADDRESS
B4
Description A SBR must be programmed after the end statement, not in the main body of the program or in an interrupt routine. SP52 will be on and the error code will be stored in V7755. A RTC must be programmed after the end statement, not in the main body of the program or in an interrupt routine. SP52 will be on and the error code will be stored in V7755. A RT must be programmed after the end statement, not in the main body of the program or in an interrupt routine. SP52 will be on and the error code will be stored in V7755. An INT must be programmed after the end statement, not in the main body of the program. SP52 will be on and the error code will be stored in V7755. An IRTC must be programmed after the end statement, not in the main body of the program. SP52 will be on and the error code will be stored in V7755. An IRT must be programmed after the end statement, not in the main body of the program. SP52 will be on and the error code will be stored in V7755. Either the DLBL instruction has been programmed in the main program area (not after the END statement), or the DLBL instruction is on a rung containing input contact(s). An ACON or NCON must be programmed after the end statement, not in the main body of the program. SP52 will be on and the error code will be stored in V7755. MLS instructions must be numbered in ascending order from top to bottom. A timer or counter contact is being used where the associated timer or counter does not exist. One of the contacts is missing from a TMRA instruction. One of the contacts is missing from a CNT or UDC instruction. One of the contacts is missing from the SR instruction.
E435 INVALID RT ADDRESS Appendix B Error Codes E436 INVALID INT ADDRESS
E437 INVALID IRTC ADDRESS
E438 INVALID IRT ADDRESS E440 INVALID DATA ADDRESS E441 ACON/NCON E451 BAD MLS/MLR E453 MISSING T/C E454 BAD TMRA E455 BAD CNT E456 BAD SR
B5
Appendix A DL405 Error Codes
DL05 Error Code E461 STACK OVERFLOW E462 STACK UNDERFLOW E463 LOGIC ERROR E464 MISSING CKT E471 DUPLICATE COIL REFERENCE E472 DUPLICATE TMR REFERENCE E473 DUPLICATE CNT REFERENCE E499 PRINT INSTRUCTION
Description More than nine levels of logic have been stored on the stack. Check the use of OR STR and AND STR instructions. An unmatched number of logic levels have been stored on the stack. Insure the number of AND STR and OR STR instructions match the number of STR instructions. A STR instruction was not used to begin a rung of ladder logic. A rung of ladder logic is not terminated properly. Two or more OUT instructions reference the same I/O point.
Invalid PRINT instruct usage. Quotations and/or spaces were not entered or entered incorrectly.
B6
DL05 Error Code E501 BAD ENTRY E502 BAD ADDRESS E503 BAD COMMAND E504 BAD REF/VAL Appendix B Error Codes E505 INVALID INSTRUCTION E506 INVALID OPERATION E520 BAD OPRUN E521 BAD OPTRUN E523 BAD OPTPGM E524 BAD OPPGM E525 MODE SWITCH E526 OFF LINE E527 ON LINE E528 CPU MODE E540 CPU LOCKED E541 WRONG PASSWORD E542 PASSWORD RESET E601 MEMORY FULL E602 INSTRUCTION MISSING
Description An invalid keystroke or series of keystrokes was entered into the handheld programmer. An invalid or out of range address was entered into the handheld programmer. An invalid command was entered in the handheld programmer. An invalid value or reference number was entered with an instruction. An invalid instruction was entered into the handheld programmer.
An operation which is invalid in the RUN mode was attempted by the handheld programmer. An operation which is invalid in the TEST RUN mode was attempted by the handheld programmer. An operation which is invalid in the TEST PROGRAM mode was attempted by the handheld programmer. An operation which is invalid in the PROGRAM mode was attempted by the handheld programmer. An operation was attempted by the handheld programmer while the CPU mode switch was in a position other than the TERM position. The handheld programmer is in the OFFLINE mode. To change to the ONLINE mode use the MODE the key. The handheld programmer is in the ON LINE mode. To change to the OFF LINE mode use the MODE the key. The operation attempted is not allowed during a Run Time Edit. The CPU has been password locked. To unlock the CPU use AUX82 with the password. The password used to unlock the CPU with AUX82 was incorrect.
The CPU powered up with an invalid password and reset the password to 00000000. A password may be re-entered using AUX81. Attempted to enter an instruction which required more memory than is available in the CPU. A search function was performed and the instruction was not found.
B7
Appendix A DL405 Error Codes
DL05 Error Code E603 DATA MISSING E604 REFERENCE MISSING E620 OUT OF MEMORY E621 EEPROM NOT BLANK E622 NO HPP EEPROM E623 SYSTEM EEPROM E624 V-MEMORY ONLY E625 PROGRAM ONLY E626 PROM MC E627 BAD WRITE E628 EEPROM TYPE ERROR E640 COMPARE ERROR E641 VOLUME LEVEL
Description A search function was performed and the data was not found. A search function was performed and the reference was not found.
An attempt to transfer more data between the CPU and handheld programmer than the receiving device can hold. An attempt to write to a non-blank EEPROM in the handheld programmer was made. Erase the EEPROM and then retry the write. A data transfer was attempted with no EEPROM (or possibly a faulty EEPROM) installed in the handheld programmer. A function was requested with an EEPROM in the handheld programmer which contains system information only. A function was requested with an EEPROM in the handheld programmer which contains V-memory data only. A function was requested with an EEPROM in the handheld programmer which contains program data only. An attempt to transfer data from a tape to a UVPROM Memory Cartridge. This transfer must be made using a CMOS RAM Cartridge. An attempt to write to a write-protected or faulty EEPROM in the handheld programmer was made. Check the write protect jumper and replace the EEPROM if necessary. The wrong size EEPROM is being used in the handheld programmer. This error occurs when the program size is larger than what the HPP can hold. A compare between the EEPROM handheld programmer and the CPU was found to be in error. The volume level of the cassette player is not set properly. Adjust the volume and retry the operation. Appendix B Error Codes
E642 An error was detected while data was being transferred to the handheld CHECKSUM ERROR programmers Memory Cartridge. Check cabling and retry the operation. E650 HPP SYSTEM ERROR E651 HPP ROM ERROR E652 HPP RAM ERROR E653 MC BATTERY LOW A system error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. A ROM error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. A RAM error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. The battery in the CMOS RAM cartridge is low and should be replaced.
1C
C2
Instruction Execution Times
Introduction
This appendix contains several tables that provide the instruction execution times for DL05 Micro PLCs. Many of the execution times depend on the type of data used with the instruction. Registers may be classified into the following types: S Data (word) Registers S Bit Registers V-Memory Data Registers Some V-memory locations are considered data registers, such as timer or counter current values. Standard user V memory is classified as a V-memory data register. Note that you can load a bit pattern into these types of registers, even though their primary use is for data registers. The following locations are data registers:
Data Registers Timer Current Values Counter Current Values User Data Words DL05 V0 - V177 V1000 - V1177 V1200 - V7377 V7400 - V7577
You may recall that some of the discrete points such as X, Y, C, etc. are automatically mapped into V memory. The following bit registers contain this data:
Bit Registers Input Points (X) Output Points (Y) Control Relays (C) Stages (S) Timer Status Bits Counter Status Bits Special Relays (SP) DL05 V40400 - V40417 V40500 - V40517 V40600 - V40637 V41000 - V41017 V41100 - V41107 V41140 - V41147 V41200 - V41237
Some instructions can have more than one parameter. For example, the SET instruction shown in the ladder program to the right can set a single point or a range of points.
In these cases, execution times that depend on the amount and type of parameters. The execution time tables list execution times for both situations, as shown below:
SET RST 1st #: 2nd #: 1st #: 2nd #: X, Y, C, S X, Y, C, S X, Y, C, S X, Y, C, S (N pt) (N pt) 32.2 ms 14ms+3.1msxN 34.4 ms 16+3.2xN
Execution depends on numbers of locations and types of data used
C3
Instruction Execution Times
Boolean Instructions
Instruction STR STRN OR ORN AND ANDN ANDSTR ORSTR OUT OROUT NOT PD STRPD STRND ORPD ORND ANDPD ANDND SET RST Legal Data Types X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP None None X, Y, C X, Y, C None X, Y, C X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP X, Y, C, T, CT, S, SP 1st #: 2nd #: 1st #: 2nd #: 1st #: 2nd #: PAUSE 1wd: Y 2wd: Y (N points) X, Y, C, S X, Y, C, S X, Y, C, S X, Y, C, S (N pt) T, CT T, CT (N pt) (N pt) Execute 2.0 ms 2.3 ms 1.6 ms 1.9 ms 1.4 ms 1.6 ms 1.3 ms 1.3 ms 6.8 ms 6.7 ms 1.6 ms 52.3 ms 20.2 ms 20.1 ms 20.0 ms 19.8 ms 20.0 ms 19.9 ms 32.2 ms
DL05 Not Execute 2.0 ms 2.3 ms 1.6 ms 1.9 ms 1.4 ms 1.6 ms 1.3 ms 1.3 ms 6.8 ms 6.7 ms 1.6 ms 53.0 ms 12.9 ms 13.0 ms 12.6 ms 12.7 ms 12.6 ms 12.8 ms 3.7 ms 4.7 ms 3.7 ms 4.7 ms 3.7 ms 4.9 ms 23.0 ms 19.5+1.4xN
C4
Instruction Execution Times Comparative Boolean Instructions
DL05 Not Execute 16.8 ms 16.8 ms 11.6 ms 42.7 ms 42.7 ms 16.8 ms 16.8 ms 11.6 ms 42.7 ms 42.7 ms 42.7 ms 42.7 ms 38.0 ms 66.7 ms 66.7 ms 42.7 ms 42.7 ms 38.0 ms 66.7 ms 66.7 ms 17.3 ms 17.3 ms 12.0 ms 43.1 ms 43.1 ms 17.3 ms 17.3 ms 12.0 ms 43.1 ms 43.1 ms 43.1 ms 43.1 ms 38.4 ms 67.1 ms 67.1 ms 43.1 ms 43.1 ms 38.4 ms 67.1 ms 67.1 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
STRNE
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C5
Instruction Execution Times
DL05 Not Execute 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 37.6 ms 37.6 ms 42.5 ms 66.4 ms 66.4 ms 37.6 ms 37.6 ms 42.5 ms 66.4 ms 66.4 ms 16.8 ms 16.8 ms 11.7 ms 42.9 ms 42.9 ms 16.8 ms 16.8 ms 11.7 ms 42.9 ms 42.9 ms 42.8 ms 42.8 ms 38.0 ms 66.7 ms 66.7 ms 42.8 ms 42.8 ms 38.0 ms 66.7 ms 66.7 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
ORNE
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C6
Instruction Execution Times
DL05 Not Execute 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 42.5 ms 42.5 ms 37.6 ms 66.3 ms 66.3 ms 42.5 ms 42.5 ms 37.6 ms 66.3 ms 66.3 ms 16.8 ms 16.8 ms 11.7 ms 42.9 ms 42.9 ms 16.8 ms 16.8 ms 11.7 ms 42.9 ms 42.9 ms 42.9 ms 42.9 ms 38.1 ms 66.8 ms 66.8 ms 42.9 ms 42.9 ms 38.1 ms 66.8 ms 66.8 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
ANDNE
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C7
Instruction Execution Times
DL05 Not Execute 16.9 ms 16.9 ms 11.6 ms 42.7 ms 42.7 ms 16.9 ms 16.9 ms 11.6 ms 42.7 ms 42.7 ms 16.9 ms 16.9 ms 11.6 ms 42.7 ms 42.7 ms 42.8 ms 42.8 ms 38.0 ms 66.7 ms 66.7 ms 42.8 ms 42.8 ms 38.0 ms 66.7 ms 66.7 ms 17.2 ms 17.2 ms 12.0 ms 43.1 ms 43.1 ms 17.2 ms 17.2 ms 12.0 ms 43.1 ms 43.1 ms 17.2 ms 17.2 ms 12.0 ms 43.1 ms 43.1 ms 43.1 ms 43.1 ms 38.4 ms 67.1 ms 67.1 ms 43.1 ms 43.1 ms 38.4 ms 67.1 ms 67.1 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
STRN
1st T, CT
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C8
Instruction Execution Times
DL05 Not Execute 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 16.5 ms 16.5 ms 11.4 ms 42.5 ms 42.5 ms 42.5 ms 42.5 ms 37.6 ms 66.4 ms 66.4 ms 42.5 ms 42.5 ms 37.6 ms 66.4 ms 66.4 ms 15.8 ms 15.8 ms 10.8 ms 41.9 ms 41.9 ms 15.8 ms 15.8 ms 10.8 ms 41.9 ms 41.9 ms 15.8 ms 15.8 ms 10.8 ms 41.9 ms 41.9 ms 41.8 ms 41.8 ms 37.1 ms 65.9 ms 65.9 ms 41.8 ms 41.8 ms 37.1 ms 65.9 ms 65.9 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
ORN
1st T, CT
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C9
Instruction Execution Times
DL05 Not Execute 15.6 ms 15.6 ms 10.9 ms 41.6 ms 41.6 ms 15.6 ms 15.6 ms 10.9 ms 41.6 ms 41.6 ms 15.6 ms 15.6 ms 10.9 ms 41.6 ms 41.6 ms 41.6 ms 41.6 ms 36.9 ms 65.6 ms 65.6 ms 41.6 ms 41.6 ms 36.9 ms 65.6 ms 65.6 ms 15.7 15.7 10.8 41.9 41.9 15.7 ms 15.7 ms 10.8 ms 41.9 ms 41.9 ms 15.7 ms 15.7 ms 10.8 ms 41.9 ms 41.9 ms 41.8 ms 41.8 ms 37.8 ms 65.9 ms 65.9 ms 41.8 ms 41.8 ms 37.8 ms 65.9 ms 65.9 ms
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
ANDN
1st T, CT
V: Bit Reg.
P:Indir. (Data)
P:Indir. (Bit)
C10
Instruction Execution Times Immediate Instructions
Immediate Instructions
Instruction STRI STRNI ORI ORNI ANDI ANDNI OUTI OROUTI SETI RSTI X X X X X X Y Y 1st #: 2nd #: 1st #: 2nd #: Y Y Y Y (N pt) (N pt) Legal Data Types Execute 38.2 ms 38.5 ms 37.7 ms 38.2 ms 37.7 ms 38.1 ms 77.5 ms 85.7 ms 68.0 ms
DL05 Not Execute 38.2 ms 38.5 ms 37.7 ms 38.2 ms 37.7 ms 38.1 ms 77.5 ms 85.7 ms 3.2 ms 4.3 ms 3.3 ms 4.4 ms
108.5ms+1.6msxN 66.9 10.8ms+1.7msxN DL05 Execute 64.0 ms 64.0 ms 58.1 ms 91.0 ms 91.0 ms 64.8 ms 64.8 ms 59.5 ms 92.5 ms 92.5 ms 72.2 ms 72.2 ms 65.7 ms 99.2 ms 99.2 ms 71.4 ms 71.4 ms 65.2 ms 98.9 ms 98.9 ms 79.5 ms 79.5 ms 73.7 ms 107.0 ms 107.0 ms
Not Execute 59.0 ms 59.0 ms 53.1 ms 86.0 ms 86.0 ms 57.3 ms 57.3 ms 52.0 ms 85.0 ms 85.0 ms 66.5 ms 66.5 ms 60.0 ms 93.5 ms 93.5 ms 65.6 ms 65.6 ms 59.5 ms 93.1 ms 93.1 ms 66.9 ms 66.9 ms 61.1 ms 94.4 ms 94.4 ms
TMRF
1st T
TMRA
1st T
TMRAF
1st T
CNT
1st CT
C11
Instruction Execution Times
DL05 Not Execute 75.3 ms 75.3 ms 69.6 ms 105.4 ms 105.4 ms 101.1 ms 101.1 ms 94.6 ms 128.0 ms 128.0 ms 31.4 ms
UDC
1st CT
SR
43.4ms+25.6msxN DL05
Not Execute 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 4.9 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.8 ms 3.8 ms 3.8 ms 3.8 ms 4.7 ms 2.7 ms
LDD
LDF
65.8ms+13.9msxN 42.7 ms 16.6 ms 16.6 ms 41.8 ms 41.8 ms 18.1 ms 18.1 ms 43.3 ms 43.3 ms
O: (Octal constant for address) V:Data Reg. V:Bit Reg. P:Indir. (Data) P:Indir. (Bit) V:Data Reg. V:Bit Reg. P:Indir. (Data) P:Indir. (Bit) 1st X, Y, C 2nd K:Constant (N pt)
OUTD
OUTF
61.9ms+22msxN 41.1 ms
POP
None
C12
Instruction Execution Times Logical Instructions
DL05 Not Execute 3.9 ms 3.9 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.9 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.8 ms 3.8 ms 3.8 ms 3.8 ms 3.7 ms 3.7 ms 3.7 ms 3.9 ms 3.9 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.9 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.9 ms 3.9 ms 3.7 ms 3.8 ms 3.8 ms DL05 Execute 140.7 ms 140.7 ms 185.1 ms 185.1 ms 152.4 ms 152.4 ms 123.2 ms 193.5 ms 193.5 ms 148.1 ms 148.1 ms 192.7 ms 192.7 ms Not Execute 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms
ANDD
OR
ORD
XOR
XORD
CMP
CMPD
Math Instructions
ADDD
SUB
C13
Instruction Execution Times
DL05 Not Execute 3.9 ms 3.9 ms 3.9 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.8 ms 3.8 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.7 ms 3.8 ms 3.8 ms 3.7 ms 3.7 ms 3.4 ms 3.4 ms 3.4 ms 3.4 ms 3.3 ms 3.3 ms 3.3 ms 3.3 ms 3.3 ms 3.3 ms 3.3 ms 3.6 ms 3.6 ms 3.3 ms 3.3 ms 3.5 ms 3.2 ms 3.2 ms 3.2 ms 3.2 ms 3.3 ms 3.2 ms 3.2 ms 3.3 ms 3.3 ms 3.3 ms 3.2 ms 3.2 ms
MUL
MULD
DIV
DIVD
INC
DEC
ADDB
SUBB
MULB
DIVB
C14
Instruction Execution Times
DL05 Not Execute 3.4 ms 3.4 ms 3.3 ms 3.3 ms 2.5 ms 2.5 ms 3.4 ms 3.4 ms DL05 Execute 19.2 ms 23.0 ms 23.0 ms 20.3 ms 29.7 ms 29.7 ms 20.4 ms 12.6 ms 20.3 ms DL05 Not Execute 2.3 ms 3.4 ms 3.4 ms 3.3 ms 3.4 ms 3.4 ms 3.3 ms 2.3 ms 2.3 ms
DECB
Bit Instructions
SHFL
ENCO DECO
Table Instructions
MOV MOVMC
Table Instructions
Instruction Legal Data Types V:Data Reg. / V:Bit Reg. P:Indir. (Data) / P:Indir. (Bit) Move from E2 to V:Data Reg. Move from E2 to V:Bit Reg. N= #of words K Execute
63ms+16msxN
50ms+15msxN 33.5 ms
3.3 ms 4.2 ms
LDLBL
C15
Instruction Execution Times CPU Control Instructions
DL05 Not Execute 14.5 ms 64.4 ms 14.8 ms 1.5 ms 12.1 ms 21.2 ms 35.2 ms 30.9 ms
Interrupt Instructions
Interrupt Instructions
Instruction ENI DISI INT IRTC IRT None None O(0,1) None None Legal Data Types Execute 24.2 ms 9.4 ms 7.5 ms 0.9 ms 6.6 ms
Network Instructions
Network Instructions
Instruction RX Legal Data Types X, Y, C, T, CT, SP, S, $ V:Data Reg. V:Bit Reg. P:Indir. (Data) P:Indir. (Bit) X, Y, C, T, CT, SP, S, $ V:Data Reg. V:Bit Reg. P:Indir. (Data) P:Indir. (Bit) Execute 852.0 ms 852.0 ms 852.0 ms 868.2 ms 868.2 ms 1614.0 ms 1614.0 ms 1614.0 ms 1630.0 ms 1630.0 ms
DL05 Not Execute 4.4 ms 4.4 ms 4.4 ms 4.2 ms 4.2 ms 4.4 ms 4.4 ms 4.4 ms 4.4 ms 4.4 ms
WX
C16
Instruction Execution Times Message Instructions
Message Instructions
Instruction FAULT Legal Data Types V:Data Reg. V:Bit Reg. K:Constant K K A ASCII Execute 65.0 ms 65.0 ms 204.7 ms 631.0 ms
Drum Instructions
Drum Instructions
Instruction DRUM EDRUM CT CT Legal Data Types Execute 840.0 ms 753.2 ms
Special Relays
1D
In This Appendix. . . .
D2
Special Relays
Always ON 1 minute clock 1 second clock 100 ms clock 50 ms clock Alternate scan
Forced run mode Terminal run mode Test run mode Test stop mode Terminal PGM mode Forced stop Forced stop mode
on when the mode switch is in the run position and the CPU is running. on when the CPU is in the run mode. on when the CPU is in the test run mode. on when the CPU is in the test stop mode. on when the mode switch is the the TERM position and the CPU is in program mode. on when the mode switch is in the STOP position. on when the STOP instruction is executed.
Interrupt enabled on when interrupts have been enabled using the ENI instruction.
D3
Special Relays System Monitoring
SP36 SP37 SP40 SP41 SP42 SP44 SP45 SP46 SP50 SP51 SP52 Override setup relay Scan control error Critical error Warning on when the override function is used. on when the actual scan time runs over the prescribed scan time. on when a critical error such as I/O communication loss has occurred. on when a non critical error has occurred.
Diagnostics error on when a diagnostics error or a system error occurs. Program memory error I/O error Communications error Fault instruction Watch Dog timeout Grammatical error Solve logic error Communication error Table instuction overrun Value less than Value equal to Greater than Zero Half borrow Borrow Half carry Carry Sign Pointer reference error Overflow Data error Load zero on when a memory error such as a memory parity error has occurred. on when an I/O error such as a blown fuse occurs. on when a communication error occurs on any of the CPU ports. on when a Fault Instruction is executed. on if the CPU Watch Dog timer times out. on if a grammatical error has occurred either while the CPU is running or if the syntax check is run. V7755 will hold the exact error code. on if CPU cannot solve the logic. on whent RX, WX, RD, WT instructions are executed with the wrong parameters. on if a table instruction with a pointer is executed and the pointer value is outside the table boundary. on when the accumulator value is less than the instruction value. on when the accumulator value is equal to the instruction value. on when the accumulator value is greater than the instruction value. on when the result of the instruction is zero (in the accumulator.) on when the 16 bit subtraction instruction results in a borrow. on when the 32 bit subtraction instruction results in a borrow. on when the 16 bit addition instruction results in a carry. when the 32 bit addition instruction results in a carry. on anytime the value in the accumulator is negative. on when the V-memory specified by a pointer (P) is not valid. on if overflow occurs in the accumulator when a signed addition or subtraction results in an incorrect sign bit. on if a BCD number is expected and a nonBCD number is encountered. on when any instruction loads a value of zero into the accumulator.
Accumulator Status
SP60 SP61 SP62 SP63 SP64 SP65 SP66 SP67 SP70 SP71 SP73 SP75 SP76
D4
Special Relays HSIO Pulse Catch Relay Appendix A HSIO Pulse Output Relay Communication Monitoring Relays
SP100 X0 is on X0 on for 1 scan after a pulse on X0 occurs.
SP116 SP117
Communications on when port 2 is the master and has a communication error. error Port 2
SP540 Current = target value SP541 Current = target value SP542 Current = target value SP543 Current = target value SP544 Current = target value SP545 Current = target value SP546 Current = target value SP547 Current = target value SP550 Current = target value SP551 Current = target value
on when the counter current value equals the value in V2320 / V2321. on when the counter current value equals the value in V2322 / V2323. on when the counter current value equals the value in V2324 / V2325. on when the counter current value equals the value in V2326 / V2327. on when the counter current value equals the value in V2330 / V2331. on when the counter current value equals the value in V2332 / V2333. on when the counter current value equals the value in V2334 / V2335. on when the counter current value equals the value in V2336 / V2337. on when the counter current value equals the value in V2340 / V2341. on when the counter current value equals the value in V2342 / V2343. on when the counter current value equals the value in V2344 / V2345. on when the counter current value equals the value in V2346 / V2347 on when the counter current value equals the value in V2350 / V2351. on when the counter current value equals the value in V2352 / V2353. on when the counter current value equals the value in V2354 / V2355. on when the counter current value equals the value in V2356 / V2357.
SP552 Current = target value SP553 Current = target value SP554 Current = target value SP555 Current = target value SP556 Current = target value SP557 Current = target value
D5
Special Relays
SP560 Current = target value SP561 Current = target value SP562 Current = target value SP563 Current = target value SP564 Current = target value SP565 Current = target value SP566 Current = target value SP567 Current = target value on when the counter current value equals the value in V2360 / V2361. on when the counter current value equals the value in V2362 / V2363. on when the counter current value equals the value in V2364 / V2365. on when the counter current value equals the value in V2366 / V2367. on when the counter current value equals the value in V2370 / V2371. on when the counter current value equals the value in V2372 / V2373. on when the counter current value equals the value in V2374 / V2375. on when the counter current value equals the value in V2376 / V2377.
1E
E2
Member Countries
Applicable Directives
E3
The end user of the products must comply with any Directives that may cover maintenance, disposal, etc. of equipment or various components. Although we strive to provide the best assistance available, it is impossible for us to test all possible configurations of our products with respect to any specific Directive. Because of this, it is ultimately your responsibility to ensure that your machinery (as a whole) complies with these Directives and to keep up with applicable Directives and/or practices that are required for compliance. As of January 1, 1999, the DL05, DL205, DL305, and DL405 PLC systems manufactured by Koyo Electronics Industries or FACTS Engineering, when properly installed and used, conform to the Electromagnetic Compatibility (EMC), Low Voltage Directive, and Machinery Directive requirements of the following standards. S EMC Directive Standards Revelant to PLCs EN500811 Generic emission standard for residential, commercial, and light industry EN500812 Generic emission standard for industrial environment. EN500821 Generic immunity standard for residential, commercial, and light industry EN500822 Generic immunity standard for industrial environment. S Low Voltage Directive Standards Applicable to PLCs EN610101 Safety requirements for electrical equipment for measurement, control, and laboratory use. S Product Specific Standard for PLCs EN611312 Programmable controllers, equipment requirements and tests. This standard replaces the above generic standards for immunity and safety. However, the generic emissions standards must still be used in conjunction with the following standards: EN 61000-3-2 Harmonics EN 61000-3-2 Fluctuations PLCDirect is currently in the process of changing their testing procedures from the generic standards to the product specific standards. Special Installation The installation requirements to comply with the requirements of the Machinery Directive, EMC Directive and Low Voltage Directive are slightly more complex than Manual the normal installation requirements found in the United States. To help with this, we have published a special manual which you can order: S DAEUM EU Installation Manual that covers special installation requirements to meet the EU Directive requirements. Order this manual to obtain the most up-to-date information.
Appendix E EU Directives
E4
Although the EMC Directive gets the most attention, other basic Directives, such as the Machinery Directive and the Low Voltage Directive, also place restrictions on the control panel builder. Because of these additional requirements it is recommended that the following publications be purchased and used as guidelines: S BSI publication TH 42073: February 1996 covers the safety and electrical aspects of the Machinery Directive S EN 602041:1992 General electrical requirements for machinery, including Low Voltage and EMC considerations S IEC 100052: EMC earthing and cabling requirements S IEC 100051: EMC general considerations It may be possible for you to obtain this information locally; however, the official source of applicable Directives and related standards is: The Office for Official Publications of the European Communities L2985 Luxembourg; quickest contact is via the World Wide Web at http://euroop.eu.int/indexn.htm Another source is: British Standards Institution Sales Department Linford Wood Milton Keynes MK14 6LE United Kingdom; the quickest contact is via the World Wide Web at http://www.bsi.org.uk
Appendix E EU Directives
E5
AC Mains Filters
DL05, DL205 and DL305 AC powered base power supplies require extra mains filtering to comply with the EMC Directive on conducted RF emissions. All PLC equipment has been tested with filters from Schaffner, which reduce emissions levels if the filters are properly grounded (earth ground). A filter with a current rating suitable to supply all PLC power supplies and AC input modules should be selected. We suggest the FN2010 for DL05/DL205 systems and the FN2080 for DL305 systems. DL405 systems do not require extra filtering.
Filter
Schaffner FN2010
To AC Input Circuitry
Earth Terminal
NOTE: Very few mains filters can reduce problem emissions to negligible levels. In some cases, filters may increase conducted emissions if not properly matched to the problem emissions. Suppression and Fusing
In order to comply with the fire risk requirements of the Low Voltage and Machinery
Directive electrical standards EN 610101, and EN 602041, by limiting the power into unlimited mains circuits with power leads reversed, it is necessary to fuse both AC and DC supply inputs. You should also install a transient voltage suppressor across the power input connections of the PLC. Choose a suppressor such as a metal oxide varistor, with a rating of 275VAC working voltage for 230V nominal supplies (150VAC working voltage for 115V supplies) and high energy capacity (eg. 140 joules). Transient suppressors must be protected by fuses and the capacity of the transient suppressor must be greater than the blow characteristics of the fuses or circuit breakers to avoid a fire risk. A recommended AC supply input arrangement for Koyo PLCs is to use twin 3 amp TT fused terminals with fuse blown indication, such as DINnectors DNF10L terminals, or twin circuit breakers, wired to a Schaffner FN2010 filter or equivalent, with high energy transient suppressor soldered directly across the output terminals of the filter. PLC system inputs should also be protected from voltage impulses by deriving their power from the same fused, filtered, and surge-suppressed supply. Appendix E EU Directives
A heavy-duty star earth terminal block should be provided in every cubicle for the connection of all earth ground straps, protective earth ground connections, mains filter earth ground wires, and mechanical assembly earth ground connections. This should be installed to comply with safety and EMC requirements, local standards, and the requirements found in IEC 100052.The Machinery Directive also requires that the common terminals of PLC input modules, and common supply side of loads driven from PLC output modules should be connected to the protective earth ground terminal.
E6
Key
Adequate site earth grounding must be provided for equipment containing modern electronic circuitry. The use of isolated earth electrodes for electronic systems is forbidden in some countries. Make sure you check any requirements for your particular destination. IEC 100052 covers equi-potential bonding of earth grids adequately, but special attention should be given to apparatus and control cubicles that contain I/O devices, remote I/O racks, or have inter-system communications with the primary PLC system enclosure. An equi-potential bond wire must be provided alongside all serial communications cables, and to any separate items of the plant which contain I/O devices connected to the PLC. The diagram shows an example of four physical locations connected by a communications cable.
Screened Cable
Appendix E EU Directives
Good quality 24 AWG minimum twisted-pair shielded cables, with overall foil and braid shields are recommended for analog cabling and communications cabling outside of the PLC enclosure. To date it has been a common practice to only provide an earth ground for one end of the cable shield in order to minimize the risk of noise caused by earth ground loop currents between apparatus. The procedure of only grounding one end, which primarily originated as a result of trying to reduce hum in audio systems, is no longer applicable to the complex industrial environment. Shielded cables are also efficient emitters of RF noise from the PLC system, and can interact in a parasitic manner in networks and between multiple sources of interference.
E7
Multidrop Cables
The recommendation is to use shielded cables as electrostatic pipes between apparatus and systems, and to run heavy gauge equi-potential bond wires alongside all shielded cables. When a shielded cable runs through the metallic wall of an enclosure or machine, it is recommended in IEC 100052 that the shield should be connected over its full perimeter to the wall, preferably using a conducting adapter, and not via a pigtail wire connection to an earth ground bolt. Shields must be connected to every enclosure wall or machine cover that they pass through. Providing an earth ground for both ends of the shield for analog circuits provides the perfect electrical environment for the twisted pair cable as the loop consists of signal and return, in a perfectly balanced circuit arrangement, with connection to the common of the input circuitry made at the module terminals. RS232 cables are handled in the same way. RS422 twin twisted pair, and RS485 single twisted pair cables also require a 0V link, which has often been provided in the past by the cable shield. It is now recommended that you use triple twisted pair cabling for RS422 links, and twin twisted pair cable for RS485 links. This is because the extra pair can be used as the 0V inter-system link. With loop DC power supplies earth grounded in both systems, earth loops are created in this manner via the inter-system 0v link. The installation guides encourage earth loops, which are maintained at a low impedance by using heavy equi-potential bond wires. To account for nonEuropean installations using single-end earth grounds, and sites with far from ideal earth ground characteristics, we recommend the addition of 100 ohm resistors at each 0V link connection in network and communications cables.
Last Slave
TXD 0V RXD + + 100W 100W 100W Termination Termination
Slave n
TXD 0V RXD + +
Master
RXD 0V TXD + +
When you run cables between PLC items within an enclosure which also contains Shielded Cables within Enclosures susceptible electronic equipment from other manufacturers, remember that these cables may be a source of RF emissions. There are ways to minimize this risk. Standard data cables connecting PLCs and/or operator interfaces should be routed well away from other equipment and their associated cabling. You can make special serial cables where the cable shield is connected to the enclosures earth ground at both ends, the same way as external cables are connected. For safety reasons, it is a specific requirement of the Machinery Directive that a keyswitch Network Isolation must be provided that isolates any network input signal during maintenance, so that remote commands cannot be received that could result in the operation of the machinery. The FAISONET does not have a keyswitch! Use a keylock and switch on your enclosure which when open removes power from the FAISONET. To avoid the introduction of noise into the system, any keyswitch assembly should be housed in its own earth grounded steel box and the integrity of the shielded cable must be maintained. Again, for further information on EU directives we recommend that you get a copy of our EU Installation Manual (DAEUM). Also, if you are connected to the World Wide Web, you can check the EU Commisions official site at: http://europ.eu.int/
Appendix E EU Directives