Professional Documents
Culture Documents
Ogata Root Locus
Ogata Root Locus
Notice that the pade approximation depends o n the dead time T a n d the desired order for t h e approximating transfer function.
1 . Locate the open-loop poles and zeros on the complex plane. Root loci exist on the negative real axis between 0 and -1 and between -2 and -3. 2. The number of open-loop poles and that of finite zeros are the same.This means that there are no asymptotes in the complex region of the s plane.
(2)
3. Determine the breakaway and break-in points.The characteristic equation for the system IS
dK rls
(2s + l ) ( s + 2 ) ( s + 3 )
s(s
+ 1 ) ( 2 >+ 5 )
[ ( s + 2 ) ( s + 3)12
as follows:
Notice that both points are on root loci. Therefore, they are actual breakaway or break-in points. At point s = -0.634, the value of K is
Similarly, at s
-2.36h,
(Because points = -0.634 lies between two poles,it is a breakaway point, and because point
s = -2.366 lies between two zeros, it is a break-in point.)
4. Determine a sufficient number of points t h d satisfy the angle condition. (It can he found
that the root loci involve a circle with center at -1.5 that passes through the breakaway and break-in points.) The root-locus plot for this system is shown in Figure 6-3Y(h). Note that this system is stable for m y positive value of K since all the root loci lie in the lefthalf s plane. Small kalues of I*: (0 c K < 0.0718) correspond to an overdampcd system. Medium value\ 01' I< (0.0718 .-: K . ; 14) correspond to an underdamped system. Finally. large values ol K ( 14 = K ) correspond to an overdamped systern. With a large value of K , the steady state can be I-eachcdin much shorter time than with a \mall value o f I<. The value of K should be adjusted so thal system performance is optimum according to ;I given performance index. Example Problems and Solutions
385
A-6-2.
Sketch the root loci of the control system shown in Figure 6-40(a).
Solution. The open-loop poles are located at s = 0, s = -3 + j4, and s = -3 - j4. A root locus branch exists on the real axis between the origin and -oo.There are three asymptotes for the root 1oci.The angles of asymptotes are
Angles of asymptotes
Referring to Equation (6-13), the intersection of the asymptotes and the real axis is obtained as
Next we check the breakaway and break-in points. For this system we have
K = -s(s2
Now we set
+ 6s + 25)
which yields
Notice that at points s = -2 ~2.0817 the ang!e condition is not satisfied. Hence, they are neither breakaway nor break-in points. In fact, if we calculate the value of K, we obtain
(To be an actual breakaway or break-in point, the corresponding value of K must be real and positive.) The angle of departure from the complex pole in the upper half s plane is
The points where root-locus branches cross the imaginary axis may be found by substituting s = j w into the characteristic equation and solving the equation for w and K as follows: Noting that the characteristic equation is
we have
which yields
Root-locus branches cross the imaginary axis at w = 5 and w = -S.The value of gain K at the crossing points is 150. Also, the root-locus branch on the real axis touches the imaginary axis at w = 0. Figure 6-40(b) shows a root-locus plot for the svstern. It is noted that if the order of the numerator of G ( s ) H ( s )is lower than that of the denominator by two or more, and if some of the closed-loop poles move on the root locus toward the right as gain K is increased, then other closed-loop poles must move toward the left as gain K is increased.This fact can be seen clearly in this problem. If the gain K is increased from K = 34 to K = 68, the complex-conjugate closed-loop poles are moved from s = -2 + 13.65 to s = -1 j4: the third pole is moved from s = -2 (which corresponds to K = 34) to s = -4 (which corresponds to K = 68).Thus, the movements of two complex-conjugate closed-loop poles to the right by one unit cause the remaining closed-loop pole (real pole in this case) to move to the left by two units.
A-6-3.
Consider the system shown in Figure 6-41(a). Sketch the root loci for the system. Observe that for small or large values of K the system is underdamped and for medium values of K it is overdamped.
Solution. A root locus exists on the real axis between the origin and -m. The angles of asymptotes of the root-locus branches are obtained as
Angles of asymptotes
=
+180(2k
3
+ 1)
=
The intersection of the asymptotes and the real axis is located on the real axis at
(b)
The breakaway and break-in points are found from d K / d s = 0. Since the characteristic equation is s3 + 49' + 5s + K = 0 we have K = -( s3 + 4s2 + 5s) . Now we set
which yields s = -1.6667 s = -1, Since these points are on root loci, they are actual breakaway or break-in points. (At points = -1, the value of K is 2, and at point s = -1.6667, the value of K is 1.852.) The angle of departure from a complex pole in the upper half s plane is obtained from
+ 5(jw) + K
Root-locus branches cross the imaginary axis at w = fiand w = -fl. The root-locus branch on the real axis touches the jw axis at w = 0. A sketch of the root loci for the system is shown in Figure 641(b). Note that since this system is of third order, there are three closed-loop poles. The nature of the system response to a given input depends on the locations of the closed-loop poles. For 0 < K < 1.852, there are a set of complex-conjugate closed-loop poles and a real closedloop pole. For 1.852 5 K < 2 , there are three real closed-loop poles. For example, the closedloop poles are located at
s = -1.667, s = -1.667, s = -1, s = -0.667, s = -2,
s = -1,
For 2 < K , there are a set of complex-conjugate closed-loop poles and a real closed-loop pole Thus, small values of K ( 0 < K < 1.852) correspond to an underdamped system. (Since the real closed-loop pole dominates, only a small ripple may show up in the transient response.) Medium values of K (1.852 5 K < 2 ) correspond to an overdamped system. Large values of K ( 2 < K ) correspond to an underdamped system. With a large value of K , the system responds much faster than with a smaller value of K . Sketch the root loci for the system shown in Figure 6-42(a).
Solution. The open-loop poles are located at s = 0 , s = -1, s = -2 + j3, and s = -2 - j3. A root locus exists on the real axis between points s = 0 and s = -1. The angles of the asymptotes are found as follows:
Angles of asymptotes
=
+180(2k 4
+ 1)
(4
Figure 6-42 (a) Control system; (b) root-locus plot.
Example Problems and Solutions
The intersection of the asymptotes and the real axis is found from
The breakaway and break-in points are found from d K / d s = 0. Noting that
K
=
-s(s
we have
it is an actual breakaway point.The gain values K Point s = -0.467 is o n a root locus.Tl~erefore, corresponding to points s = -1.642 f 12.067 are complex quantities. Since the gain values are not real positive, these points are neither breakaway nor break-in points. The angle of departure from the complex pole in the upper half s plane is
Next we shall find the points where root loci may cross the jw axis. Since the characteristic equation is
K = 37.44
or
w =
0,
K =0
The root-locus branches that extend to the right-half s plane cross the imaginary axis at w = 11.6125. Also, the root-locus branch o n the real axis touches the imaginary axis at w = 0. Figure 6-42(b) shows a sketch of the root loci for the system. Notice that each root-locus branch that extends to the right half s plane crosses its own asymptote.
Chapter 6 /
Root-Locus Analysis
Ad-5.
Sketch the root loci for the system shown in Figure 6-43(a).
Solution. A root locus exists on the real axis between points s = -1 and s = -3.6. The asymptotes can be determined as follows:
Angles of asymptotes =
+180(2k
+ 1)
3-1
90, -90"
The intersection of the asymptotes and the real axis is found from
The breakaway and break-in points are found from (3s' + 7.2s)(s + 1) - ( s 3 + 3.6s') dK
-
ds
(S
from which we get Point s = 0 corresponds to the actual breakaway point. But points s = 1.65 f j0.9367 are neither breakaway nor break-in points, because the corresponding gain values K become complex quantities. To check the points where root-locus branches may cross the imaginary axis, substitute s = jw into the characteristic equation, yielding. ( j ~ +) 3~ . 6 ( j ~+ )~ Kjw
+K
Notice that this equation can be satisfied only if w = 0, K = 0. Because of the presence of a double pole at the origin, the root locus is tangent to the jw axis at o = 0. The root-locus branches do not cross the jw axis. Figure 6-43(b) is a sketch of the root loci for this system. A-6-6. Sketch the root loci for the system shown in Figure 6-44(a).
Solution. A root locus exists on the real axis between point s = -0.4 and s asymptotes can be found as follows:
Angles of asymptotes
=
*180(2k 3-1
+ 1)
= 90, -90"
The intersection of the asymptotes and the real axis is obtained from
Next we shall find the breakaway points. Since the characteristic equation is
we have
Thus, the breakaway or break-in points are at s = 0 and s = -1.2. Note that s = -1.2 is a double root. When a double root occurs in dK/ds = 0 at point s = -1.2, d2K/(ds2) = 0 at this point.The value of gain K at point s = -1.2 is
This means that with K = 4.32 the characteristic equation has a triple root at points = -1.2.This can be easily verified as follows:
Hence, three root-locus branches meet at point s = -1.2. The angles of departures at point s = -1.2 of the root locus branches that approach the asymptotes are f180/3, that is, 60" and
-60". (See Problem A-6-7.) Finally, we shall examine if root-locus branches cross the imaginary axis. By substituting s = jw into the characteristic equation, we have
This equation can be satisfied only if w = 0, K = 0. A t point w = 0, the root locus is tangent to the j o axis because of the presence of a double pole at the origin. There are no points that rootlocus branches cross the imaginary axis. A sketch of the root loci for this system is shown in Figure 6-44(b).
Example Problems and Solutions
A-6-7.
Referring to Problem A-6-6, obtain the equations for the root-locus branches for the system shown in Figure 6-44(a). Show that the root-locus branches cross the real axis at the breakaway point at angles f60".
Solution. The equations for the root-locus branches can be obtained from the angle condition
/s
+ 0.4
2 b - /s
+ 3.6 = *180(2k + 1)
By substituting s
+ jw, we obtain
By rearranging, we have
tan-'
(-)u + 0.4
W
- tan-'
):(
= tan-'
):(
*l8O0(2k
+ 1)
Taking tangents of both sides of this last equation, and noting that
we obtain
The equation w = 0 represents the real axis. The root locus for 0 5 K 5 co is between points s = -0.4 and s = -3.6. (The real axis other than this line segment and the origin s = 0 corresponds to the root locus for -w 5 K < 0.) The equations
represent the complex branches for 0 5 K 5 m.These two branches lie between a = -1.6 and u = 0. [See Figure 6-44(b).] The slopes of the complex root-locus branches at the breakaway point ( a = -1.2) can be found by evaluating d o l d a of Equation (6-21) at point a = -1.2.
Since tan-'
A-6-8.
60, the root-locus branches intersect the real axis with angles +60
Consider the system shown in Figure 6-45(a), which has an unstable feedforward transfer function. Sketch the root-locus plot and locate the closed-loop poles. Show that, although the closedloop poles lie on the negative real axis and the system is not oscillatory, the unit-step response curve will exhibit overshoot. Solution. The root-locus plot for this system is shown in Figure 6-45(b).The closed-loop poles are located at s = -2 and s = -5. The closed-loop transfer function becomes
Closed-loop zero
(a)
Figure 6-46 Unit-step response curve for the system shown in Figure 6-45 (a). The unit-step response of this system is
fort
The unit-step response curve is shown in Figure 6-46. Although the system is not oscillatory, the unit-step response curve exhibits overshoot. (This is due to the presence of a zero at s = -1.)
A-6-9.
Sketch the root loci of the control system shown in Figure &47(a). Determine the range of gain K for stability.
Solution. Open-loop poles are located at s = 1,s = -2 + j d , and s = -2 - j d . A root locus exists on the real axis between points s = 1 and s = -03. The asymptotes of the root-locus branches are found as follows:
Angles of asymptotes
=
*180(2k 3
+ 1)
0. Since
-( r - l ) ( s 2 + 4s
+ 7) = -(s3 + 3s2 + 3s - 7)
which yields
(s
+I
) = ~0
(a)
Thus the equation d K / d s = 0 has a double root at 3 = -1. (This means that the characteristic equation has a triple root at s = -1.) The breakaway point is located at s = -1. Three root-locus branches meet at this breakaway point.The angles of departure of the branches at the breakaway point are ilX0/3, that is. 60" and -60". We shall next determine the points where root-locus branches may cross the imaginary axis. Noting that the characteristic equation is
(.r
-
l)(.s2
+ 4s + 7 ) + K
+K
-
or
.r +
we substitute s
=
3 ,+ ~3~ .~ - 7
+3
-
( j ~ ) ~ 3(jw)
+K
(K
This equation is satisfied when
=
3w2) + ,043
w2) = 0
K=7+3w"l6
or
w=0,
The root-locus branches cross the imaginary axis at w = h d (where K = 16) and w = 0 (where K = 7). Since the value of gain K at the origin is 7, the range of gain value K for stability is
Figure 6-47(b) shows a sketch of the root loci for the system. Notice that all branches consist of parts of straight lines. The fact that the root-locus branches consist of straight lines can be verified as follows: Since the angle condition is
we have -1s
-
1 - /s +2
+j f l -
/s + 2
jd=h180(2k
+ 1)
By substituting s = a
+ jw
/u
+ 2 + j(w + d) + / a + 2 + j(w
tan
d) = -/a
+ jw
f 180(2k
+ 1)
(w
+ a
)+t
w - v 3
) = -tan-'(*)
* LW(2k + 1)
+ 2)
w a - 1
q2+4CT+4-w2+3
+ 2 ) ( u - 1 ) = -w(a2 + 4 a + 7 - W 2 )
w(3a2 + 6 u
+ 3 - w2) = 0
398
Chapter 6 /
Root-i.o<cis Analysis
Thus the root-locus branches consist of three lines. Note that the root loci for K > 0 consist of portions of the straight lines as shown in Figure 6-47(b). (Note that each straight line starts from an open-loop pole and extends to infinity in the direction of 180, 60, or -60" measured from the real axis.) The remaining portion of each straight line corresponds to K < 0.
A-6-10.
Consider the system shown in Figure 6-48(a). Sketch the root loci
Solution. The open-loop zeros of the system are located at s = fj. The open-loop poles are located at s = 0 and s = -2. This system involves two poles and two zeros. Hence, there is a possibility that a circular root-locus branch exists. In fact, such a circular root locus exists in this case, as shown in the following. The angle condition is
By substituting s
we obtain
which is equivalent to
These two equations are equations for the root 1oci.The first equation corresponds to the root locus on the real axis. (The segment between s = 0 and s = -2 corresponds to the root locus for 0 5 K < m.The remaining parts of the real axis correspond to the root locus for K < 0.) The second equation is an equation for a circle. Thus, there exists a circular root locus with center at u = i, w = 0 and the radius equal to a / 2 . The root loci are sketched in Figure 6-48(b). [That part of the circular locus to the left of the imaginary zeros corresponds to K > 0. The portion of the circular locus not shown in Figure 6-48(b) corresponds to K < 0.1
A-6-11.
Consider the control system shown in Figure 6-49. Plot the root loci with MATLAB.
Solution. MATLAB Program 6-11 generates a root-locus plot as shown in Figure 6-50.The root loci must be symmetric about the real axis. However, Figure 6-50 shows otherwise. MATLAB supplies its own set of gain values that are used to calculate a root-locus plot. It does so by an internal adaptive step-size routine. However, in certain systems, very small changes in the gain cause drastic changes in root locations within a certain range of gains.Thus,MATLAB takes too big a jump in its gain values when calculating the roots, and root locations change by a relatively large amount. When plotting, MATLAB connects these points and causes a strange-looking graph at the location of sensitive gains. Such erroneous root-locus plots typically occur when the loci approach a double pole (or triple or higher pole), since the locus is very sensitive to small gain changes.
num = [O 0 1 0.41; den = [ I 3.6 0 01; rlocus(num,den); v = [-5 1 -3 31; axis(v) grid title('Root-Locus Plot of G(s) = K(s + 0.4)/[sA2(s+ 3.6))')
Real Axis
In the problem considered here, the critical region of gain K is between 4.2 and 4.4.Thus we need to set the step size small enough in this region. We may divide the region for K as tollows:
Entering MATLAB Program 6-12 into the computer, we obrain the plot as shown in Figure 6-51, If we change the plot command plot(r,'o') in MATLAB P r ~ g r a m 6-12 to plot(r,'-'1, we obtain Figure 6-52. Figures 6-51 and 6-52 respectively, show satisfa~tc~ry root-locus plots.
MATLAB Program 6-1 2 "A, - - - - - . - - - - Root-locus plot ---------num = [O 0 I 0.41; den = [ I 3.6 0 01; K1 = [0:0.2:4.21; K2 = [4.2:0.002:4.4]; K3 = [4.4:0.2:10]; K4 = [ I 0:5:200]; K = [KI K2 K3 K4]; r = rlocus(num,den,K); plot(r,'ol) v = [-5 1 -5 51; axis(v) grid titIe('Root-Locus Plot of G(s) = K(s + 0.4)/[sA2(s xlabel('Rea1 Axis') ylabel('lmag Axis')
Example Problems and Solutions
-5
-5
0
6
-4
-3
-2 Real A X I S
-1
Real Axis
Solution. We shall plot the root loci and asymptotes on one diagram. Since the open-loop transfer function is given by K G ( s ) H ( s )= s(s + l ) ( s + 2 ) K s3 + 3s2 + 2s the equation for the asymptotes may be obtained as follows: Noting that K K K == lim lim 3+m s3 + 3~~ + 2~ S-'m S~ 3 ~+ 2 3~ + 1 ( S + q3
num = [O O O 11 den = [ I 3 2 01
the number of rows of r and that of a must be the same. To ensure this, we include the gain constant K in the commands. For example,
MATLAB Program 6-1 3 num = [O O O I ] ; den = [ I 3 2 01; numa = [O 0 0 1 I; dena = [ I 3 3 1I; K1 = 0:0.1:0.3; K2 = 0.3:0.005:0.5; K3 = 0.5:0.5:10; K4 = 1O:S:I 00; K = [Kl K2 K3 K4]; r = rlocus(num,den,K); a = rlocus(numa,dena,K); y = [r a]; plot(y,'-'1 v = [-4 4 -4 41; axis(v) grid title('Root-Locus Plot of G(s) = K/[s(s + 1 )(s + 2)) and Asymptotes') xlabel('Rea1 Axis') ylabeU1lmagAxis') ***** Manually draw open-loop poles in the hard copy *****
Example Problems and Solutions
Real Axis
Including gain K in rlocus command ensures that the r matrix and a matrix have the same number of rows. MATLAB Program 6-13 will generate a plot of root loci and their asymptotes. See Figure 6-53. Drawing two or more plots in one diagram can also be accomplished by using the hold command. MATLAB Program 6-14 uses the hold command. The resulting root-locus plot is shown in Figure 6-54.
MATLAB Program 6-1 4 01~ ---- - ---- - -- Root-Locus Plots -----------num = [O 0 0 1 I; den = [ I 3 2 01; numa = [O 0 0 11; dena = (1 3 3 1 I; K1 = 0:0.1:0.3; K2 = 0.3:O.OOS:O.S; K3 = O.5:0.5:10; K4 = 10:5:100; K = [ K l K2 K3 K4]; r = rlocus(num,den,K); a = rlocus(numa,dena,K); plot(r,'ol) hold Current plot held plot(a,'-'1 v = [-4 4 -4 41; axis(v) grid title('Root-Locus Plot of G(s) = K/[s(s+l )(s+2)1 and Asymptotes') xlabel('Rea1 Axis') ylabel('lmag Axis')
Chapter 6 / Root-Locus Analysis
Figure 6-54
Root-locus plot. Real Axis Consider a unity-feedback system with the following feedforward transfer function G ( s ) :
K(s + 2 ) ' C(s)= (s' + 4 ) ( s + 5)' Plot root loci for the system with MATLAB.
Solution. A MATLAB program to plot the root loci is given as MATLAB Program 6-15. The resulting root-locus plot is shown in Figure 6-55. Notice that this is a special case where no root locus exists on the real axis.This means that for any value of K > 0 the closed-loop poles of the system are two sets of complex-conjugate poles. ( N o real closed-loop poles exist.) For example, with K = 25, the characteristic equation for the system becomes
+ 10s' + 54s' + 140s + 200 = ( s L + 4s + 10)(s2 + 6s + 20) = (S + 2 + j2.4495)(s + 2 - j2.44!X)(s + 3 + ;3.3166)(s + 3 - j3.3166)
s4
Real Axis
Since no closed-loop poles exist in the right-half s plane, the system is stable for all values of K > 0.
A-6-14.
Consider a unity-feedback control system with the following feedforward transfer function:
Plot a root-locus diagram with MATLAB. Superimpose on the s plane constant 5 lines and constant w , circles.
Solution. MATLAB Program 6-16 produces the desired plot as shown in Figure 6-56.
--
Figure 6-56 Root-locus plot with constant 6 lilies and constant w,, c:ircles.
Real Axis
A-6-15.
Consider a unity-feedback control system with the following feedforward transfer function:
Plot root loci for the system with MATLAB. Show that the system is stable for all values of K > 0.
Solution. MATLAB Program 6-17 gives a plot of root loci as shown in Figure 6-57. Since the root loci are entirely in the left-half s plane, the system is stable for all K > 0.
num = [O 1 0 25 01; den = [ I 0 404 0 16001; K = 0:0.4:1000; rlocus(num,den,K) v = [-30 20 -25 251; axis(v); axis('square') grid title('Root-Locus Plot of G(s) = K(sA2+ 25)s/(sA4+ 404sA2 + 1600)')
A-6-16.
A simplified form of the open-loop transfer function of an airplane with an autopilot in the longitudinal mode is
Such a system involving an open-loop pole in the right-half s plane may be conditionally stable. Sketch the root loci when a = b = 1, (' = 0.5, and w,, = 4. Find the range of gain K for stability.
Example Problems and Solutions
407
Real Axis
2. Determine the asymptotes of the root loci.There are three asymptotes whose angles can be determined as
Angles of asymptotes
=
Referring to Equation (6-13), the abscissa of the intersection of the asymptotes and the real axis is
3. Determine the breakaway and break-in points. Since the characteristic equation is
we obtain
+ 24s -
16
Points s = 0.45 and s = -2.26 are on root loci on the real axis. Hence, these points are actual breakaway and break-in points, respectively. Points s = -0.76 f 12.16 d o not satisfy the angle condition. Hence, they are neither breakawav nor break-in points.
4. Using Routh's stability criterion, determine the value of K at which the root loci cross the imaginary axis. Since the characteristic equation is
The values of K that make the s' term in the first column equal zero are K = 35.7 and K = 23.3. The crossing points on the imaginary axis can be found by solving the auxiliary equation obtained from the s2row, that is, by solving the following equation for s:
kj2.56, ij1.56,
for K for K
= =
35.7 23.3
~tj2.56 and s
=
ij1.56.
5. Find the angles of departure of the root loci from the complex poles. For the open-loop pole at s = -2 + j 2 d , the angle of departure 8 is
or
H = -54.5"
s =
-2
12fl is 54S0.)
6. Choose a test point in the broad neighborhood of the jw axis and the origin, and apply the angle condition. If the test point does not satisfy the angle condition, select another test point until it does. Continue the same process and locate a sufficient number of points that satisfy the angle condition.
Example Problems and Solutions
409
Hence
Using this approximation, determine the critical value of K (where K > 0) for stability.
+ 1 + Ke-"
Applying the Routh stability criterion, we get the Routh table as follows:
-6K2
which can be written as (K or
36K
+ 114 > 0
+ 8.2915)(K
- 2.2915)
<0
Consider the system shown in Figure 6-60.The plant involves the dead time of T sec. Design a suitable controller G,(s) for the system.
Solution. We shall present the Smith predictor approach to design a controller. The first step to design the controller G,(s) is to design a suitable controller G, ( s ) when the system has no dead time. Otto J. M. Smith designed an innovative controller scheme, now called the "Smith predictor,"
Example Problems and Solutions
41 1
Hence, the block diagram of Figure 6-61(a) can be modified to that of Figure 6-61(b).The closedloop response of the system with dead time e-TJis the same as the response of the system without dead time c - ~ ' , except that the response is delayed by T sec. Typical step-response curves of the system without dead time controlled by the controller &,(s) and of the system with dead time controlled by the Smith predictor type controller are shown in Figure 6-62. It is noted that implementing the Smith predictor in digital form is not difficult, because dead time can be handled easily in digital control. However, implementing the Smith predictor in an analog form creates some difficulty.
Step Response
0.5
1.5
3.5
4.5
PROBLEMS
B-6-1. Plot the root loci for the closed-loop control system with
B-6-3. Plot the root loci for the closed-loop control system with
. .
B-6-2. Plot the root loci for the closed-loop control system with
Problems
413
B-6-12. Consider the system whose open-loop transfer function G ( s ) H ( s )is given by
Determine the exact points where the root loci cross the jw axis.
8-64. Show that the root loci for a control system with
are arcs of the circle centered at the origin with radius equal to
m.
8-6-7. with
B-6-8. with
Using MATLAB, plot the root loci and asymptotes for the svstem.
B-6-9. with
Locate the closed-loop poles on the root loci such that the dominant closed-loop poles have a damping ratio equal to 0.5. Determine the corresponding value of gain K.
B-6-10. Plot the root loci for the system shown in Figure 6-63. Determine the range of gain K for stability.
B-6-15. Consider the system shown in Figure 6-64. Plot the root loci with MATLAB. Locate the closed-loop poles when the gain K is set equal to 2.
Figure 6-63 Control system.
R-6-11. Consider a unity-feedback control system with the following feedforward transfer function:
u
Plot the root loci for the system. If the value of gain K is set equal to 2, where are the closed-loop poles located?
414
B-6-16. Plot root-locus diagrams for the nonminimumphase systems shown in Figures 6-65(a) and (b), respectively.
Figure 6-66
Control system.
Figure 4-65
(a) and (b) Nonminimum-phase systems.
Problems