Cb-Olx425 Electrical Mechanical Data Sheet: Document Revision
Cb-Olx425 Electrical Mechanical Data Sheet: Document Revision
Copyright 2012 connectBlue AB. The contents of this document can be changed by connectBlue AB without prior notice and do not constitute any binding undertakings from connectBlue AB. connectBlue AB is not responsible under any circumstances for direct, indirect, unexpected damage or consequent damage that is caused by this document. All rights reserved. All brand and product names are trademarks or service marks of their respective owners.
Page 1 of 44
connectBlue
1 Table of Content
1 Table of Content 2 Introduction 2.1 Product Variants 2.2 Block Diagram 2.3 Bluetooth Stack and Application software 3 Electrical Interface and Connectors 3.1 Interfaces 3.2 Peripherals 3.3 Pin Numbering 3.4 Pin Description 3.5 Characteristics 3.6 Hardware Reset 4 Antennas 4.1 Surface Mounted Antennas (Internal) 4.2 External antennas 5 Mechanics 5.1 Module Outlines 5.2 Antenna Issues 6 Bluetooth Information 6.1 General information 7 Regulatory Information 7.1 Declaration of Conformity 7.2 Safety Compliance 7.3 FCC and IC Compliance 7.4 UL listing information 7.5 Compliance with RoHS directive 8 Guidelines for Efficient and Safe Use 8.1 General 8.2 Product Care 8.3 Radio Frequency Exposure 8.4 Electronic Equipment 8.5 Potentially Explosive Atmospheres 8.6 Power Supply
Page 2 of 44
connectBlue
2 Introduction
The license could not be verified: There is no license certificate installed for CustomWare Scaffolding Plugin for Confluence.
The connectBlue OLP425 is a Bluetooth low energy platform module with a unique set of features and functionality that provides customers with a turnkey complete solution. The OLP425 can either be delivered as is with digital and analog GPIOs or complete with battery holder, temperature sensor, 3-axis motion sensor/accelerometer, switch. There are also 4x1 through holes for solder wires or through hole components. Using the IAR Embedded Workbench, the customer embeds their own software and application in the OLP425 module. Such possible software includes Bluetooth low energy profiles/services/attributes and customer application such as machine/device access and asset management, data conversion, data acquisition, logic etc.
The hardware of the cB-OLP425 product is referred as cB-0950 and the module is Type Approved with the type name cB-0950. The module is available in different configuration (see Product Variants) with internal antennas or a U.FL. connector for connecting an external antenna.
Page 3 of 44
connectBlue
Page 4 of 44
connectBlue
cB-OLP425i-26***
OEM Low Energy Platform 425 with internal antenna, JST connector, LEDs, Temperature Sensor, Accelerometer and CR1632 battery holder.
cB-OLP425x-04
OEM Low Energy Platform 425 with external antenna. No battery holder, no sensors, no JST connector, no LEDs.
Page 5 of 44
connectBlue
cB-OLP425x-26*** cB-0950 PVH0950 5325A-0950 Bluetooth Low Energy Output power: 3 to 6 dBm EIRP** Sensitivity: TBD to TBD dBm EIRP** OEM Low Energy Platform 425 with external antenna, JST connector, LEDs, Temperature Sensor, Accelerometer and CR1632 battery holder.
The license could not be verified: There is no license certificate installed for CustomWare Scaffolding Plugin for Confluence.
* EIRP is including antenna gain. ** EIRP is including antenna gain and cable loss and thus depends on the antenna selection. *** The JST connector is specified down to -25 C. See #E nvironmental for more information.
Please contact connectBlue for discussion about customer specific mounting options. Components that are available for optional mountings are: CR1632 coin cell battery holder 3-axis motion sensor / accelerometers Temperature sensor Pushbutton JST connector 2x LEDs Internal antenna or u.fl. connector for external antenna Through hole mounted analog or digital discrete sensors (4x1 through holes at 1.27 mm pitch) PCB wings/flaps with holes for mounting of the module (module size including wings 16x36 mm) Voltage regulator for 3.0-6.0 VDC power supply
Page 6 of 44
connectBlue
Page 7 of 44
connectBlue
TIP For higher quantity orders the customer developed software/firmware may be loaded to the module during the production at connectBlue.
Page 8 of 44
connectBlue
Figure 3: The solder pads J6 are available on the long edges of the bottom side of the PCB.
Figure 4: The JST connector J8 mounted on the component side of the PCB.
Page 9 of 44
connectBlue
3.2 Peripherals
The OEM Low Energy Platform can be customized to suit an end application e.g. with the on board 3 axes motion sensor, the temperature sensor and two LEDs. There are also a 4x1 through holes (1.27mm pitch) available for solder wires or through holes components to the board (see Pin Numbering for more info).
3.2.2 Accelerometer
A ST Microelectronics LIS3DH 2/4/8/16 g accelerometer is available on board. The communication is via IC with the device address 0x19. The communication interface is an software implemented IC: Signal SDA SCL Interrupt1 CC2540 port P1-6 P1-5 P1-3 Description Serial Data Clock Interrupt signal (optional)
3.2.3 LEDs
One green and one red LED are available on board: LED Green Red CC2540 port P1-4 P1-7 Description Active Low green signal Active low red signal
Page 10 of 44
connectBlue
CMOS
In
Hardware reset
3.0 V
Out
3, 25 4, 27
4 -
1 2
Ground 3.0 V In
2.0 - 3.6 VDC power supply. The module does not have an external voltage regulator mounted by default, but can be mounted for 3.0-6.0 VDC supply. Please contact connectBlue for more information. Reserved, do not connect.
14-17, 19-22
CMOS
In
CMOS
Out
CMOS
In/Out
CMOS
Out
10
CMOS
In
UART0 (alt1) Clear To Send. Hardware flow control. Active low (multiplexed/connected with SPI-CS). UART0 (alt1) Transmit Data. "0" : Low, "1" : High (multiplexed/connected with SPI-MOSI).
11
16 / P0_3
CMOS
Out
Page 11 of 44
connectBlue
12 14 / P0_5 CMOS Out UART0 (alt1) Request To Send. Hardware flow control. Active low (multiplexed/connected with SPI-CLK) UART0 (alt1) Receive Data. "0" : Low, "1" : High (multiplexed/connected with SPI-MISO) Data Terminal Ready. Active low/ CC2540 Debug Data. Data Set Ready. Active low/ CC2540 Debug Clock. SPI interrupt signal.
13
17 / P0_2 35 / P2_1 34 / P2_2 36 / P2_0 17 / P0_2 14 / P0_5 16 / P0_3 15 / P0_4 35 / P2_1 19 / P0_0
CMOS
In
CMOS
Out/ In/Out In
18
CMOS
23
CMOS
In
24
CMOS
Master In/ Slave Out Master Out/ Slave In Master Out/ Slave In Master Out/ Slave In In/Out
SPI0 (alt2) master input slave output (multiplexed/connected with UART-RxD) SPI0 (alt2) clock (multiplexed/connected with UART-RTS) SPI0 (alt2) master output slave input (multiplexed/connected with UART-TxD) SPI0 (alt2) chip select (multiplexed/connected with UART-CTS) CC2540 Debug Data (multiplexed/connected with UART-DTR). Analog input.
26
CMOS
28
CMOS
29
CMOS
30
CMOS
31
Analog (0-VCC)
In
32
In
Analog input.
33
In
Analog input.
34
In
Analog input.
35
Out
IC-SCL: IC clock.
36
CMOS
Out / Bidirectional
Page 12 of 44
connectBlue
The license could not be verified: There is no license certificate installed for CustomWare Scaffolding Plugin for Confluence.
Page 13 of 44
connectBlue
3.5 Characteristics
3.5.1 Power supply
NOTE Read the Guidelines for Efficient and Safe Use before using the modules.
Table 3: Power supply Symbol VCC Parameter Power supply Min Max Value 2.0* 3.6* Unit VDC VDC
* The module does not have an external voltage regulator mounted by default but can be mounted for 3.0-6.0 VDC supply. Please contact connectBlue for more info.
Table 4: Current consumption Symbol ICC@ VCC = 3.0V Peak Not connected, stop mode enabled Not connectable, not discoverable Average TBD TBD mA mA Mode Not connected Connectable, discoverable Average Value TBD Unit mA
TBD TBD
mA mA
Peak Connectable, discoverable Average Peak Connected Idle or Receiving Average Peak
mA mA mA mA mA
Page 14 of 44
connectBlue
Transmitting @TBD kbit/s Average Peak TBD TBD mA mA
) internal pull-up
Min
3.5.3 Environmental
Table 6: Temperatures characteristics Parameter Storage temperature Min Model Without JST connector With JST connector Max Without JST connector With JST connector Value -40 -25 +125 +85 Unit C C C C
Page 15 of 44
connectBlue
Operating temperature Min Without JST connector With JST connector Max All -40 -25 +85 C C C
source must be open drain collector, see section #Reset for design examples. The pulled-up with 15kOhm.
Page 16 of 44
connectBlue
The license could not be verified: There is no license certificate installed for CustomWare Scaffolding Plugin for Confluence.
4 Antennas
This chapter gives a quality overview of the different antenna options. There are 2 different antenna options available: Internal surface mounted (SMD) antenna. An U.FL. connector for external antennas. Different types of external antennas are available. The sections below lists the antennas that are included in the radio type approvals of the module. For each antenna the "Approvals" field defines in which test reports the antenna is included. Definitions of the "Approvals" field are: FCC - The antenna is included in the FCC test reports, and thus approved for use in countries that accept the FCC radio approvals, primarily US. IC - The antenna is included in the IC (Industrie Canada) test reports, and thus approved for use in countries that accept the IC radio approvals, primarily Canada. R&TTE - The antenna is included in the R&TTE test reports, and thus approved for use in countries that accept the R&TTE radio approvals, primarily the European countries. In general, antennas with SMD antenna, Reverse Polarity SMA connector or U.FL connector are included in FCC, IC and R&TTE radio tests. Antennas with SMA connector are in general included in R&TTE radio tests but not FCC or IC due to FCC/IC regulations.
The antenna gain is very dependent of the mounting of the module. See section Antenna Issues for mounting the module considering the antenna.
Page 17 of 44
connectBlue
Approval FCC, IC and R&TTE
Page 18 of 44
connectBlue
U.FL and SMA jack (outer thread and pin receptacle) 120 mm Less than 0.5dB The SMA connector may be mounted in a panel. R&TTE
Connector
U.FL and reverse polarity SMA jack (outer thread and pin) 120 mm Less than 0.5dB The reverse polarity SMA connector may be mounted in a panel.
Page 19 of 44
connectBlue
Approval FCC, IC and R&TTE
Page 20 of 44
connectBlue
ProAnt Vertical +3.0 dBi 12.0 x 28.0 mm Reverse Polarity SMA plug (inner thread and pin receptacle) To be mounted on the U.FL to Reverse Polarity SMA adapter cable (cB-ACC-38). An SMA version antenna is also available but not recommended to use (Ex-IT 2400 SMA 28-001). FCC, IC and R&TTE
Approval
Page 21 of 44
connectBlue
Connector Comment Approval U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
Page 22 of 44
connectBlue
ProAnt Vertical +3.0 dBi 10 x 83 mm Reverse Polarity SMA plug (inner thread and pin receptacle) To be mounted on the U.FL to Reverse Polarity SMA adapter cable (cB-ACC-38). An SMA version antenna is also available but not recommended to use (Ex-IT 2400 SMA 70-002). FCC, IC and R&TTE
Comment
Approval
Manufacture Polarization
ProAnt Vertical
Page 23 of 44
connectBlue
Gain Size Cable length Connector Comment +3.0 dBi 9.4 x 70.5 mm 100 mm U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
Approval
Page 24 of 44
connectBlue
cB-ACC-57 InSide-2400
ProAnt +3.0 dBi 27 x 12 mm (triangular) 100 mm U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
cB-ACC-66 FlatWhip-2400
ProAnt +3.0 dBi 50.0 x 30.0 mm SMA plug (inner thread and pin) To be mounted on the U.FL to SMA adapter cable. R&TTE
Page 25 of 44
connectBlue
Page 26 of 44
connectBlue
cB-ACC-67 Outside-2400
ProAnt +3.0 dBi 36.0 x 18.0 x 16.0 mm 70 mm U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
Page 27 of 44
connectBlue
Laird Technologies/ Centurion Vertical +2.0 dBi 100 mm (Straight) cB-ACC-16: SMA plug (inner thread and pin) cB-ACC-36: Reverse Polarity SMA plug (inner thread and pin receptacle) cB-ACC-16 is to be used together with the U.FL to SMA adapter cable (cB-ACC-18 or cB-ACC-48). cB-ACC-36 is to be used together with the U.FL to Reverse Polarity SMA adapter cable (cB-ACC-38). cB-ACC-36: FCC, IC and R&TTE cB-ACC-16: R&TTE
Comment
Approval
Page 28 of 44
connectBlue
Size Cable length 108 mm (Straight) cB-ACC-27: 100 mm cB-ACC-29: 250 mm U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
Page 29 of 44
connectBlue
cB-ACC-23 PSTG0-2400HS
Mobile Mark Communications Antennas Vertical 0 dBi 9.5 x 26 mm SMA plug (inner thread and pin) To be used together with the U.FL to SMA adapter cable (cB-ACC-18 or cB-ACC-48). An alternative Reverse Polarity SMA version antenna is available (PSTG0-2400HRS). R&TTE
Approval
cB-ACC-28 NanoBlue-IP04
Page 30 of 44
connectBlue
Connector Comment Approval U.FL. connector To be mounted on the U.FL connector on the PCB. FCC, IC and R&TTE
Page 31 of 44
connectBlue
REEL +1.0 dBi 75 x 20 mm M16 x 13.6 mm cB-ACC-17: SMA plug (inner thread and pin) cB-ACC-37: Reverse Polarity SMA plug (inner thread and pin receptacle) 300 cm. Other cable lengths are available on request. cB-ACC-17 is to be used together with the U.FL to SMA adapter cable (cB-ACC-18 or cB-ACC-48). cB-ACC-37 is to be used together with the U.FL to Reverse Polarity SMA adapter cable (cB-ACC-38). cB-ACC-37: FCC, IC and R&TTE. cB-ACC-17: R&TTE.
Approval
cB-ACC-21 R380.500.127
Manufacture Polarization
Pulse Vertical
Page 32 of 44
connectBlue
Gain Size Connector Comment +2.0 dBi 14.3 x 61.4 mm SMA plug (inner thread and pin) To be mounted on the U.FL to SMA adapter cable (cB-ACC-18 or cB-ACC-48). A Reverse Polarity SMA version is also available (R380.500.125). R&TTE
Approval
Page 33 of 44
connectBlue
R380.500.139
Pulse Vertical +2.0 dBi 14.3 x 61.1 mm Reverse Polarity SMA plug (inner thread and pin receptacle) The difference compared to the R380.500.125 antenna is that the R380.500.139 antenna has a seal ring. To be mounted on the U.FL to Reverse Polarity SMA adapter cable (cB-ACC-38). An SMA version antenna is also available (R380.500.124). FCC, IC and R&TTE
Approval
IHF-242
Page 34 of 44
connectBlue
Size Cable length Connector Comment Approval 9.2 x 82.5 mm 150 cm MCX male connector To be mounted on a MCX to U.FL adapter cable. FCC, IC and R&TTE
Page 35 of 44
connectBlue
5 Mechanics
5.1 Module Outlines
5.1.1 Module dimensions
Figure 8: cB-OLx425 dimensions with mounting wings (optional) and CR1632 battery holder. Weight: <1 g
Page 36 of 44
connectBlue
Page 37 of 44
connectBlue
6 Bluetooth Information
6.1 General information
In the tables below you can find information about Bluetooth properties. The conducted output power of the cB-OLx425 device is ~3 dBm (2mW). Table 10: Bluetooth information cB-OLx425 Parameter Bluetooth Low Energy radio RF output power (conducted - excluding antenna gain) Receive sensitive level Output frequency Bluetooth standard Data Texas Instrument CC2540F256 ~3dBm
TBD dBm 2.402 - 2.480 GHz, ISM band. 4.0 (single mode / Bluetooth Smart)
Page 38 of 44
connectBlue
7 Regulatory Information
WARNING Radio type approvals and certifications are currently in progress and not yet completed. The information in this section is provided only for reference of what approvals are to be available when the approval process is completed.
We, connectBlue AB, of Norra Vallgatan 64 3V SE-211 22 Malm, Sweden declare under our sole responsibility that our products: cB-OLP425 and cB-OLS425 (cB-0950), OEM Module Adapter III (cB-0068). to which this declaration relates, conforms to the following product specifications: R&TTE Directive 1999/5/EC: Effective use of frequency spectrum: EN 300 328 V1.7.1 (2006-10) EMC: EN 301 489-1 V1.8.1 (2008-04) EN 301 489-17 V2.1.1 (2009-05) EN 61000-6-2 (2005) Health and safety: EN 50371:2002 EN 60950-1:2006 + A11:2009 and/or IEC 60950-1:2005 (2nd Edition) Medical Electrical Equipment IEC 60601-1-2 (2007) The license could not be verified: There is no license certificate installed for CustomWare Scaffolding Plugin for Confluence.
Page 39 of 44
connectBlue
7.3.1.2 Antenna
Our module type cB-0950 is for OEM integrations only. The end-user product will be professionally installed in such a manner that only the authorized antennas are used.
7.3.1.3 Caution
Any changes or modifications NOT explicitly APPROVED by connectBlue AB could cause the module to cease to comply with FCC rules part 15, and thus void the user's authority to operate the equipment.
7.3.1.4 IC Compliance
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
Page 40 of 44
connectBlue
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device has been designed to operate with an antenna having a maximum gain of 3.5 dBi. Having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb
The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. In accordance with 47 CFR 15.19 the end product shall bear the following statement in a conspicuous location on the device: "This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation." When the device is so small or for such use that it is not practicable to place the statement above on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC ID label must be displayed on the device. In case, where the final product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual.
Page 41 of 44
connectBlue
All products based on the PCB cB-0950 are produced according to the RoHS (Restriction of the use of certain Hazardous substances in electrical and electronic equipment) directive and complies with the directive.
Page 42 of 44
connectBlue
Page 43 of 44
connectBlue
Page 44 of 44