TM 5-3805-254-20-2 Ihc F-5070 Dump Truck
TM 5-3805-254-20-2 Ihc F-5070 Dump Truck
TECHNICAL MANUAL
VOLUME 2 OF 2
ORGANIZATIONAL
MAINTENANCE
INSTRUCTIONS -
CONTINUED
PAGE 2-664
MAINTENANCE
ALLOCATION
CHART (MAC)
PAGE B-1
INDEX
PAGE Index-1
JANUARY 1988
CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 1 Washington D.C., 25 February 1993
2. New or changed material is indicated by a vertical bar in the margin and by a vertical bar adjacent to the TA number.
1
TM 5-3805-254-20-2
WARNING
Exhaust gas is without color or smell, but can kill you. Breathing exhaust gas produces symptoms of headache, dizziness,
loss of muscular control, a sleepy feeling, and coma. Brain damage or death can result from heavy exposure of exhaust
fumes of fuel-burning internal combustion engines. Exhaust gases can become dangerously concentrated under
conditions of no air movement. Precautions must be followed to ensure crew safety when the engine of any vehicle is
operated for any purpose.
1. DO NOT operate vehicle engine inside building unless ample ventilation is available.
2. DO NOT idle engine for long periods without ventilator blower operating.
3. DO NOT drive any vehicle with inspection plates, cover plates, or engine compartment doors removed unless
necessary for maintenance purposes.
4. BE ALERT at all times during vehicle operation for exhaust odors and exposure symptoms. If either is present,
IMMEDIATELY VENTILATE personnel compartments. If symptoms persist, remove affected crew to fresh air; keep
warm; DO NOT PERMIT PHYSICAL EXERCISE; and, if necessary, give artificial respiration.
6. BE AWARE; the field protective mask for chemical-biological-radiological (CBR) protection will not protect you from
exhaust gas fumes.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use only in a well-
ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do not use near open flame or
excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C) and for type #2 is 138°F (59°C). If you
become dizzy while using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is made,
flush your eyes with water and get medical aid immediately.
WARNING
Diesel fuel burns easily. Do not smoke or allow flames nearby. Disconnect batteries when working on fuel system.
Failure to observe these precautions could cause serious injury or death to personnel.
WARNING
Naphtha and its fumes are harmful and flammable. Do not use near open flame. Do not smoke while using naphtha. Use
only in well-ventilated area. Naphtha can catch fire, and fumes can explode causing injury.
a
TM 5-3805-254-20-2
WARNING
Do not let positive wire touch metal surfaces at any time. Personal injury and equipment damage will
occur.
WARNING
Edges of exhaust system components are sharp. Care must be taken to prevent personal injury.
WARNING
Metal edges of air cleaner housing are sharp. Care must be taken to prevent personal injury.
WARNING
Do not drain rear axle housing oil when hot. Hot oil can burn you.
WARNING
Do not drain interaxle differential oil when hot. Hot oil can burn you.
WARNING
Hot transmission oil can burn you. Care must be taken to prevent personal injury.
WARNING
Do not check rear axle housing oil level when hot. Hot oil can burn you.
WARNING
Support blocks must be used to support dump body weight. Death or serious injury could result if
personnel fail to observe this warning.
WARNING
Make sure all personnel are clear of dump body before lowering, to prevent injury.
WARNING
Do not operate engine after removing turbocharger piping. Foreign matter could enter turbocharger air
inlet pipe causing injury to personnel and damage to turbocharger.
WARNING
Do not touch heat shrinkable tubing for at least 30 seconds after heating. Hot tubing can burn you.
WARNING
Do not smoke or allow open flames or sparks into areas where alcohol is being used. Failure to observe
this precaution could cause death or serious injury to personnel.
b
TM 5-3805-254-20-2
WARNING
Care must be taken when taking off canister to prevent spilling alcohol. Injury to personnel could occur.
WARNING
Electrical parts solvent cleaning compound is flammable, and reacts violently with certain metals. Boiling
point is 114°F (46°C). Do not wear jewelry. Wear safety goggles, rubber gloves, and use only in well
ventilated area. Avoid contact with skin, eyes, and clothes and don’t breathe vapors. Do not use near
open flame or excessive heat. If you become dizzy while using cleaning compound, get fresh air
immediately and get medical aid. If contact with eyes is made, wash your eyes with water and get medical
aid immediately.
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
WARNING
Parts of brake assembly will be coated with asbestos dust. Breathing this dust may be hazardous to your
health. Use filter mask approved for use against asbestos dust. Never use compressed air or dry brush
to clean these assemblies. Dust shall be removed using industrial type vacuum cleaner equipped with
high efficiency filter system. Clean dirt or mud from brake assemblies with bristle brush or cloth, and
water.
WARNING
Due to excessive weight, assistance will be needed to prevent personal injury when lifting heavy parts.
WARNING
Due to excessive weight, assistance will be needed to lift and remove pintle hook assembly from rear
chassis cross-member. Serious injury to personnel could result.
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
WARNING
Hot engine oil could burn you. Care must be taken to prevent personal injury.
WARNING
Safety goggles must be worn when working with air lines to prevent personal injury.
WARNING
Safety goggles must be worn, when using chisel or drill, to prevent eye injury caused by flying steel chips.
c
TM 5-3805-254-20-2
WARNING
Safety goggles must be worn to prevent eye injury from flying metal chips when using compressed air, or
striking metal surfaces.
WARNING
Safety goggles must be worn when using wire brush. Flying rust or metal particles could cause eye injury.
WARNING
Safety goggles must be worn when using a portable electric drill. Flying metal particles could cause eye
injury.
WARNING
Brake springs under tension can injure or kill. Use extreme care to prevent injury. Safety goggles must
be worn.
WARNING
Disconnect battery ground cable before cleaning or replacing parts. This will keep you from getting
shocked or damaging parts.
WARNING
Batteries must be disconnected before working near electrical components. Failure to observe this
precaution could cause serious injury to personnel or damage to equipment.
WARNING
Drain air from airbrake system before removing lines or fittings to avoid injury to personnel from
compressed air.
WARNING
Particles blown by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent personal injury.
WARNING
Stand to side of axle flange while striking to prevent injury from flying lock collars.
WARNING
Due to excessive weight and size, assistance will be needed when handling dry air reservoir. Failure to
observe this precaution could cause injury to personnel.
d
TM 5-3805-254-20-2
WARNING
Assistant must support muffler to prevent falling and causing personal injury.
WARNING
Assistance will be needed to support hood panel to prevent falling and causing personal injury.
WARNING
WARNING
Assistant must support fuel tank support to prevent falling and causing injury.
WARNING
When jacking vehicle, be sure vehicle is on level ground. Put blocks in front and behind each wheel to
prevent vehicle from moving, and support vehicle with trestle stands to prevent personnel injury.
WARNING
Do not operate engine after removing air cleaner housing. Foreign matter could enter turbocharger air
inlet pipe causing injury to personnel and damage to turbocharger.
WARNING
Due to excessive weight, care must be taken to prevent front hub and brakedrum assembly from falling.
Do not pull out too far on spindle. Serious injury to personnel could result.
WARNING
Due to excessive weight, assistance will be needed to lift hub and brakedrum assembly. Failure to
observe this precaution could cause serious injury to personnel.
WARNING
Remove all jewelry, prior to performing any electrical troubleshooting, to prevent accidental short circuits
and/or electric shock.
WARNING
Starter motor solenoid battery terminal is capable of delivering high voltage. Do not touch or let tools or
metal parts touch starter motor solenoid battery terminal or ground. Severe personal injury or death could
occur.
WARNING
Do not smoke, use open flame, or allow sparks near batteries. Mixture of oxygen and hydrogen gases
released from batteries is highly flammable and can explode causing injury to personnel.
e
TM 5-3805-254-20-2
WARNING
Due to excessive weight, assistance will be needed to lift and take off exhaust diverter.
WARNING
When removing battery cables, disconnect ground cable first. When installing battery cables, connect
ground cable last. When two ground cables are used, both cables must be disconnected prior to working
on equipment where shorting of cables can occur. In correct cable replacement sequence is extremely
dangerous. Accidental contact of tools with vehicle causes direct short, resulting in arcing and instant
heating of tool and causing painful burns. Shorted battery may explode, causing injury to personnel.
WARNING
When removing battery cables, disconnect negative (-) cable first. Failure to observe this precaution
could cause injury to personnel or damage to equipment.
WARNING
When installing battery cables, connect negative (-) cable last. Failure to observe this precaution could
cause injury to personnel or damage to equipment.
WARNING
Do not operate engine after removing air filter element. Foreign matter could enter turbocharger air inlet
pipe and could cause damage to turbocharger or injury to personnel.
WARNING
Do not touch heater coil of glow plug when testing. Severe personal injury could occur.
WARNING
Safety props and support blocks must be used to support dump body to prevent falling and causing injury
to personnel.
WARNING
Be careful when removing radiator cap. If engine is hot, escaping steam could burn you. Use a rag to
cover radiator cap. Unscrew cap just enough to allow any built-up pressure to escape. When all pressure
has been relieved, unscrew cap and take off.
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with batteries. Failure to
observe this precaution could cause serious injury to personnel.
WARNING
Although KEY SWITCH must be on and battery ground cable connected to test electrical circuit voltage,
turn off KEY SWITCH and disconnect battery ground cable before doing resistance tests or replacing
parts. This will keep you from getting shocked and prevent damage to parts and equipment.
f
TM 53805-25420-2
WARNING
Care must be taken when working under hood while engine is running. Hands must be kept away from
belts, fan, and other moving parts. Failure to observe this precaution could cause serious injury to
personnel.
WARNING
Do not attempt to disconnect hydraulic lines and fittings while engine is running or before hydraulic system
pressure has been released. When engine is running, hydraulic system is under pressure. Hydraulic
system pressure should be 0 psi (0 kPa) before lines are disconnected. A line or fitting disconnected
under pressure will blow off with great force and can cause injury to personnel.
WARNING
When increasing air pressure in tires, be careful not to exceed recommended pressure, to prevent
personal injury or damage to equipment.
WARNING
Draining hot cooling system is not recommended. If coolant must be drained with engine hot, use gloves
to protect against hot coolant. Severe burns could result.
WARNING
Ensure that vehicle is on level ground and that rear wheels are chocked to prevent vehicle from moving or
severe injury to personnel may result.
WARNING
When performing parking brake troubleshooting, follow procedure exactly. Release of trapped air inside
brake chamber can cause brakes to apply suddenly, causing injury to personnel.
WARNING
Do not operate dump truck with tires of different construction. Injury to personnel and equipment could
occur.
WARNING
No welding, grinding or use of heat producing devices permitted near fuel tank unless fuel tank has been
cleaned and purged of all flammable liquids and vapors. Failure to observe these precautions could
cause serious injury to personnel.
WARNING
Exhaust system parts become very hot when engine is running. Allow time for parts to cool before
working on exhaust system. Hot exhaust system parts will cause serious burns.
g
TM 5-3805-254-20-2
WARNING
Be careful when bleeding torque converter cooler. Escaping steam and coolant could burn you. Open
draincock just enough to allow any built up pressure to escape.
WARNING
Cab floor boards have sharp edges. Care must be taken to prevent injury to personnel.
WARNING
Use care when removing damaged headlight assembly, broken glass or sharp metal could cut you.
WARNING
Due to excessive weights, assistance will be needed to support battery box, to prevent personal injury.
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
WARNING
Do not drain steering system when hot. Hot oil can burn you.
WARNING
Do not drain oil reservoir when hot. Hot oil can burn you.
WARNING
WARNING
To prevent injury, make sure all personnel are clear of tailgate when body is in raised position.
WARNING
Drain air from air tank system before removing lines or fittings to avoid injury to personnel from
compressed air.
h
TM 5-3805-254-20-2
You can help improve this manual. If you find any mistakes, or if you know of a way to
improve the procedures, please let us know. Mail your letter, DA Form 2028
(Recommended Changes to Publications and Blank Forms), or DA Form 2028-2 located
in the back of this manual directly to: Commander, U.S. Army Tank-Automotive
Command, ATTN: AMSTA-MBS, Warren, MI 48397-5000. A reply will be sent to you.
TABLE OF CONTENTS
VOLUME 2 OF 2
Page
* This manual supersedes organizational portion of TM 5-3805-254-14&P1 dated August 1980 and TM 5-3805-254-14&P2
dated June 1980 including all changes.
i
TM 5-3805-254-20-2
Page
TABLE OF CONTENTS - CONTINUED
VOLUME 2 OF 2 - CONTINUED
INDEX ...............................................................................................................................................Index-1
This manual is designed to help you maintain the IHC Model F-5070 (CCE) dump truck.
The front cover table of contents is provided for quick reference to important information. There is
also an index, located in the back of this manual, for use in locating specific items of information.
Measurements in this manual are given in both US standard and metric units. A metric to US
standard conversion chart can be found on the inside back cover.
Read all preliminary information found at the beginning of each task. It has important information
and safety instructions you must follow before beginning the task.
Equipment locator illustrations are also provided throughout the maintenance procedures. These
illustrations are for use in locating components and assemblies of the overall equipment. It should
be noted that the locator illustrations do not always reflect the equipment condition listed in the
initial setup at the beginning of each task.
Warning pages are located in the front of this manual. You should read the warnings before
operating or doing maintenance on the equipment.
A subject index appears at the beginning of each chapter listing sections that are included in that
chapter. A more specific subject index is located at the beginning of each section to help you find
the exact paragraph you’re looking for.
ii
TM 5-3805-254-20-2
Page Page
Change 1 2-664
TM 5-3805-254-20-2
Page Page
GENERATOR DRIVEBELTS
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Mounting bracket (1) Screw (2) and Using two 3/4-inch box-end wrenches,
nut (3) loosen one turn.
TA244127
2-665
TM 5-3805.254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Adjusting strap (1) Screw (2) Using 314-inch box-end wrench, loosen
one turn.
3. Mounting bracket (3) Generator (4) Using 16-inch pry bar, push generator
toward crankshaft pulley (5) to loosen
drivebelts (6).
INSTALLATION
CAUTION
6. Mounting bracket (3) Generator (4) Pull generator away from crankshaft pulley
(5), to seat drivebelts (6) in pulley
grooves, and hold.
7. Adjusting strap (1) Screw (2) Screw in until snug, using 3/4-inch box-end
wrench, to hold drivebelts (6) in pulley
grooves.
ADJUSTMENT
9. Mounting bracket (3) Screw (8) and Screw in and tighten using two 3/4-inch
nut (9) box-end wrenches.
2-666
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
TA244128
2-667
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Generator pulley (1) Two drivebelts (3) Take off (page 2-665).
and crankshaft
pulley (2)
2. Generator (4) Screw (5), lock- a. Using 1/2-inch open-end wrench, un-
washer (6), and screw and take out.
clamp (7) b. Get rid of lockwasher.
6. Adjusting strap (13) Screw (14) and a. Using 314-inch box-end wrench, un-
lockwasher (15) screw and take out.
b. Get rid of lockwasher.
CAUTION
Use care when performing steps 8 and 9. Damage to generator could occur.
INSTALLATION
10. Mounting Screw (17), nut Screw in until snug using 314-inch box-end
bracket (16) (18), and new lock- wrench.
washer (19)
11. Adjusting strap (13) Screw (14) and new Screw in until snug using 3/4-inch box-end
lockwasher (15) wrench.
2-668
TM 5-3805-254.20-2
ACTION
LOCATION ITEM REMARKS
13. Wire connector (11), Screw on and tighten using 7/16-inch open-
new lockwasher (10), end wrench.
and nut (9)
15. Screw (5), new Screw in and tighten using 1/2-inch open-
lockwasher (6), and end wrench.
clamp (7)
16. Generator pulley (1) Two drivebelts (3) a. Put on (page 2-665).
and crankshaft b. Adjust (page 2-665).
pulley (2)
TA244129
2-669
TM 5-3805-254.20-2
ACTION
LOCATION ITEM REMARKS
ADJUSTMENT
NOTE
Adjust generator if ampere output is not within 10 percent of rated output stamped on generator.
Go to Troubleshooting (page 2-43).
NOTE
FOLLOW-ON MAINTENANCE:
TA244130
2-670
TM 5-3805-254-20-2
GENERATOR PULLEY
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Generator pulley (1) Nut (3) and flat Using 5/16-inch socket head screw key,
and armature (2) washer (4) 15/16-inch 1/2-inch drive flare socket, and
ratchet handle, unscrew and take off.
TA244131
2-671
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Armature (1) Generator pulley (2) Using mechanical puller, pull off.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 100°F (38°C) and for type #2 is 138°F (59°C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
Parts must be cleaned thoroughly. For more information on how to clean parts, go to General
Maintenance Instructions (page 2-424).
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed away
from user and other personnel in the area. Compressed air used for cleaning purposes shall not
exceed 30 psi (207 kPa). User must wear safety goggles or face shield to prevent injury to
personnel.
4. All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
Replace all damaged or defective parts. For more information on how to inspect parts, go to
General Maintenance Instructions (page 2-424).
2-672
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
TA244132
2-673
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Engine oil pres- Five wires (2) and a. Tag wires (page 2-424).
sure switch (1) three screws (3) b. Using 3/16-inch flat-tip screwdriver,
unscrew and take out.
c. Move wires aside.
2. Elbow (4) Engine oil pres- Using 7/16-inch open-end wrench, un-
sure switch (1) screw and take out.
INSTALLATION
3. Elbow (4) Engine oil pres- a. Wipe pipe threads clean using wiping
sure switch (1) rag.
b. Wrap pipe threads with antiseizing tape
(page 2-424).
c. Screw in and tighten using 7/16-inch
open-end wrench.
4. Engine oil pres- Five wires (2) and a. Put wires in correct position.
sure switch (1) three screws (3) b. Screw in and tighten using 3/16-inch
flat-tip screwdriver.
c. Get rid of tags.
2-674
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
TA244133
2-675
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Engine water temper- Three wires (2), a. Tag wires (page 2-424).
ature switch (1) three nuts (3),and b. Using 1/4-inch box-end wrench, un-
three lockwashers (4) screw and take out.
c. Move wires aside.
d. Get rid of lockwashers.
2. Water manifold (5) Engine water temper- Using 1-inch open-end wrench, unscrew
ature switch (1) and take out.
INSTALLATION
3. Water manifold (5) Engine water temper- a. Wipe pipe threads clean using wiping
ature switch (1) rag.
b. Wrap pipe threads with antiseizing tape
(page 2-424).
c. Screw in and tighten using 1-inch open-
end wrench.
4. Engine water temper- Three wires (2), a. Put wires in correct position.
ature switch (1) three new lock- b. Screw on and tighten using 1/4-inch
washers (4), and box-end wrench.
three nuts (3) c. Get rid of tags.
TA244134
2-676
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-677
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Transmission oil Two wires (2) and a. Tag wires (page 2-424).
pressure switch (1) two screws (3) b. Using 3/16-inch flat-tip screwdriver,
unscrew and take out.
c. Move wires aside.
INSTALLATION
3. Adapter (4) Transmission oil a. Clean pipe threads using wiping rag.
pressure switch (1) b. Wrap pipe threads with antiseizing tape
(page 2-424).
c. Screw in and tighten using 5/8-inch
and 11/16-inch open-end wrenches.
4. Transmission oil Two wires (2) and a. Put wires in correct position.
pressure switch (1) two screws (3) b. Screw in and tighten using 3/16-inch
flat-tip screwdriver.
c. Get rid of tags.
TA244135
2-678
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
2-679
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
1. Left brake Two screws (2), two a. Tag wires (page 2-424).
light switch (1) lockwashers (3), and b. Using 1/4-inch flat-tip screwdriver,
two wires (4) unscrew and take out.
c. Get rid of lockwashers.
d. Move wires aside.
2. Adapter (5) Left brake light Using 9/16-inch and 11/16-inch open-end
switch (1) wrenches, unscrew and take out.
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
3. Adapter (5) Left brake light a. Clean pipe threads with wiping rag.
switch (1) b. Wrap pipe threads with antiseizing tape
(page 2-424).
c. Screw in and tighten using 9116-inch
and 11/16-inch open-end wrenches.
4. Left brake Two wires (4), two a. Put wires in correct position.
light switch (1) new lockwashers (3), b. Screw in and tighten using 1/4-inch flat-
and two screws (2) tip screwdriver.
c. Get rid of tags.
2-680
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Materials/Parts
TA244136
2-681
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
1 Right brake Two screws (2), two a Tag wires (page 2-424).
light switch (1) lockwashers (3), and b Using 114-inch flat-tip screwdriver, un-
two wires (4) screw and take out.
c Get rid of lockwashers.
d Move wires aside.
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
4 Right brake Two wires (4), two a Put wires in correct position.
light switch (1) new lockwashers (3), b Screw in and tighten using 1/4-inch flat-
and two screws (2) tip screwdriver.
c Get rid of tags.
2-682
TM 5-3805-254-20-2
RIGHT BRAKE LIGHT SWITCH - CONTINUED
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Materials/Parts
TA244137
2-683
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Engine Compression Two wires (2) and a Tag wires (page 2-424).
brake pressure two screws (3) b Using 3/16-inch flat-tip screwdriver,
switch (1) unscrew and take out.
c Move wires aside.
INSTALLATION
3 Torque converter Engine Compression a Clean pipe threads using wiping rag.
housing (4) brake pressure b Wrap pipe threads with antiseizing tape
switch (1) (page 2-424).
c Screw in and tighten using 7/16-inch
open-end wrench.
4 Engine Compression Two screws (3) and a Put wires in correct position.
brake pressure two wires (2) b Screw in and tighten using 3/16-inch
switch (1) flat-tip screwdriver.
c Get rid of tags.
2-684
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Materials/Parts
Lockwasher, switch
Rags, wiping (item 15, appendix C)
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Transmission oil Nut (2), lockwasher a Using 3/8-inch box-end wrench, un-
temperature (3), and wire (4) screw and take off.
sender (1) b Get rid of lockwasher.
TA244139
2-685
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSTALLATION
3 Torque converter Transmission oil a Clean pipe threads using wiping rag.
housing (1) temperature b Screw in and tighten using 15/16-inch
sender (2) open-end wrench.
NOTE
TA244140
2-686
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
Lockwasher, sender
Rags, wiping (item 15, appendix C)
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Transmission oil Nut (2), lockwasher a Using 3/8-inch box-end wrench, un-
temperature (3), and wire (4) screw and take off.
switch (1) b Get rid of lockwasher.
TA244141
2-687
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSTALLATION
3 Adapter (1) Transmission oil a Clean pipe threads using wiping rags.
temperature b Screw in and tighten using 15/16-inch
switch (2) and 1-inch open-end wrenches.
NOTE
TA244142
TASK ENDS HERE
2-688
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA244143
2-689
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
3. Transmission (1) Backup light a Clean pipe threads with wiping rag.
switch (2) b Wrap pipe threads with antiseizing tape
(page 2-424).
c Screw in and tighten using 1-inch open-
end wrench.
NOTE
TA244144
2-690
TM 5-380-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA244145
2-691
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
3. Transmission (1) Neutral safety a Clean pipe threads with wiping rag.
switch (2) b Wrap pipe threads with antiseizing tape
(page 2-424).
c Screw in and tighten using 7/18-inch
open-end wrench.
NOTE
2-692
TM 5-3805-254-20-2
INITIAL SETUP
Flashlight One
Screwdriver, cross-tip, number one
Screwdriver, flat-tip, 3/16-inch Equipment Condition
Wrench, open-end, 7/8-inch
Left cab door opened (page 2-424).
Materials/Parts
Lockwasher, switch
Rags, wiping (item 15, appendix C)
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA244147
2-693
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2 Cab floor (1) Power take off cover Using number one cross-tip screwdriver,
plate (2) and two unscrew and take out.
screws (3)
WARNING
Cab floor boards have sharp edges Care must be taken to prevent injury to personnel.
3 Power take off Screw (5), lock- a Using 3/16-inch flat-tip screwdriver and
light switch (4) washer (6), and flashlight, unscrew and take out.
wire (7) b Get rid of lockwashers.
4 Power take off (8) Power take off Using 7/8-inch open-end wrench and
light switch (4) flashlight, unscrew and take out.
INSTALLATION
WARNING
Cab floor boards have sharp edges Care must be taken to prevent injury to personnel.
5 Power take off (8) Power take off a Clean pipe threads with wiping rag.
light switch (4) b Screw in and tighten using 7/8-inch
open-end wrench and flashlight.
6 Power take off Wire (7), new lock- Screw in and tighten using 3/16-inch flat-tip
light switch (4) washer (6), and screwdriver.
screw (5)
2-694
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
TA244148
2-695
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
2. Fuel pump (3) Engine compression a. Using 7116-inch box-end wrench, un-
brake throttle switch screw and take out.
(1), two screws (4), b. Get rid of lockwashers.
and two lock-
washers (5)
INSTALLATION
3. Fuel pump (3) Engine compression Screw in and tighten using 7116-inch box-
brake throttle end wrench.
switch (1), two new
lockwashers (5), and
two screws (4)
ADJUSTMENT
NOTE
Engine compression brake throttle switch adjustment must be performed with throttle control pedal in idle position.
5. Adjusting screw (6) Jamnut (7) Using two 1/2-inch open-end wrenches,
loosen one turn.
6. Actuator arm (8) Adjusting screw (6) a. Screw in until engine compression
brake
throttle switch button (9) opens.
Listen for click to open.
b. Screw out until engine compression
brake throttle switch button (9) closes.
Listen for click to close.
7. Adjusting screw (6) Jamnut (7) Screw on and tighten using two 1/2-inch
open-end wrenches.
2-696
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Tools Materials/Parts
TA244149
2-697
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
2. Left manifold (5) Low air-pressure Using 8-inch slip-joint pliers, unscrew and
warning light take out.
switch (1)
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
3. Left manifold (5) Low air-pressure a. Clean pipe threads with wiping rag.
warning light b. Screw in and tighten using 8-inch slip-
switch (1) joint pliers.
2-698
TM 5-3805-254.20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools Materials/Parts
TA244150
2-699
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
2. Right manifold (5) Low air-pressure Using 8-inch slip-joint pliers, unscrew and
warning buzzer take out.
switch (1)
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
3. Right manifold (5) Low air-pressure a. Clean pipe threads with wiping rag.
warning buzzer b. Screw in and tighten using 8-inch slip-
switch (1) joint pliers.
2-700
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
TA244151
2-701
TM 5-3805-254-20-2
Equipment Condition
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Primary magnetic Two nuts (2), two a. Tag wires (page 2-424).
switch (1) lockwashers (3), b. Using 3/8-inch box-end wrench, un-
and two wires (4) screw and take out.
c. Get rid of lockwashers.
INSTALLATION
5. Primary magnetic Two screws (8) and Screw in and tighten using number two
switch (1) two new lock- cross-tip screwdriver.
washers (9)
2-702
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA244152
2-703
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
1. Secondary magnetic Nut (2), wire (3), a. Tag wire (page 2-424).
switch (1) and two lock- b. Using 11/32-inch box-end wrench, un-
washers (4) screw and take out.
c. Get rid of lockwashers.
INSTALLATION
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
2-704
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5. Secondary magnetic Two screws (8), two Screw in and tighten using 7/16-inch box-
switch (1) new lockwashers (9), end and 7116-inch open-end wrenches.
and two nuts (10)
NOTE
FOLLOW-ON MAINTENANCE:
TA244153
2-705
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Frequency sensing Two screws (2) and a. Tag wires (page 2-424).
relay switch (1) two wires (3) b. Using 3/16-inch flat-tip screwdriver,
unscrew and take off.
INSTALLATION
3. Firewall (5) and Two screws (4) Screw in and tighten using 7/16-inch box-
frequency sensing end wrench.
relay switch (1)
2-706
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
HORN RELAY
INITIAL SETUP
Tools Personnel Required
TA244154
2-707
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
INSTALLATION
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
3. Firewall (6) and Two screws (3), two Screw in and tighten using 7/16-inch box-
horn relay (1) new lockwashers (4), end and open-end wrenches.
and two nuts (5)
TA244155
2-708
TM 5-3805-254-20-2
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Equipment Condition
Materials/Parts
Battery ground cable disconnected
Lockwasher, mounting (two required) (page 2-424).
Instrument panel pad removed (page 2-424).
Right cab door opened (page 2-424).
2-709
LOW AIR-PRESSURE WARNING BUZZER - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
INSTALLATION
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
3. Firewall (6) and Two screws (3), two Screw in and tighten using 7/16-inch open-
low air-pressure new lockwashers (4), end and 7/16-inch box-end wrenches.
warning buzzer (1) and two nuts (5)
TA244156
2-710
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP:
2-711
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
INSTALLATION
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
3. Firewall (4) and Two screws (3) Screw in and tighten using number two
turn signal and cross-tip screwdriver.
hazard flasher (1)
TA244157
2-712
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
HORN BUTTON
INITIAL SETUP:
Personnel Required
One
2-713
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Steering wheel (1) Horn button (2) Turn counterclockwise and take out.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
10. Steering wheel (1) Three screws (5) Screw in and tighten using number two
and horn plate (6) cross-tip screwdriver.
2-714
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13. Horn button (2) Put in place and turn clockwise to lock.
NOTE
FOLLOW-ON MAINTENANCE:
HORN
TA244158
2-715
TM 5-3805-254-20-2
HORN - CONTINUED
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
2. Mounting bracket (3) Screw (4) and a. Using two 1/2-inch open-end
lockwasher (5) wrenches, unscrew and take out.
b. Get rid of lockwasher.
INSTALLATION
3. Mounting bracket (3) Screw (4) and new Screw in and tighten using two 1/2-inch
and fan shroud (6) lockwasher (5) open-end wrenches.
2-716
TM 5-3805-2542-02
HORN - CONTINUED
NOTE
ALARM BELL
INITIAL SETUP:
2-717
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
1. Alarm bell (1) Three screws (2), a Using 3/8-inch box-end wrench and
three nuts (3), number two cross-tip screwdriver, un-
three lockwashers screw and take out.
(4), and three b. Get rid of lockwashers.
spacers (5)
INSTALLATION
CAUTION
Use care when working behind instrument panel pad to prevent breaking or disconnecting wires.
3. Alarm bell (1) Two wires (7) and a. Put wires in place.
two screws (6) b. Screw in and tighten using 3/16-inch
flat-tip screwdriver.
c. Get rid of tags.
2-718
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
DOME LIGHT
INITIAL SETUP:
Tools Materials/Parts
TA244160
2-719
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Dome light base (1) Dome light lens (2) Using 3116-inch flat-tip screwdriver, pry
out.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
2-720
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
10. Dome light base (1) Two wires (5) a. Push on.
b. Get rid of tags.
TA244161
2-721
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
11. Dome light base (1) Two screws (2) Screw in and tighten using number one
cross-tip screwdriver.
NOTE
TA244162
2-722
TM 5-3805-254-20-2
INITIAL SETUP:
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
2-723
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Dome/panel lamp Two screws (2) Using number one cross-tip screwdriver,
switch (1) unscrew and take out.
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
4. Dome/panel lamp Two screws (2) Screw in and tighten using number one
switch (1) cross-tip screwdriver.
TA244164
2-724
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
LIGHTS SWITCH
INITIAL SETUP:
Personnel Required
One
2-725
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
1. LIGHTS switch (1) Eight connectors (2) a. Tag wires (page 2-424).
b. Pull off.
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
5. LIGHTS switch (1) Nut (3) Screw in and tighten using 9/16-inch open-
end wrench.
2-726
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
FUEL GAGE
INITIAL SETUP:
Tools MaterialslParts
TA244165
2-727
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
3. Mounting bracket (6) Two nuts (7) and a. Using 318-inch box-end wrench, un-
two lockwashers (8) screw and take out.
b. Get rid of lockwashers.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-728
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
11. Mounting bracket (6) Two new lockwashers Screw on and tighten using 3/8-inch
(8) and two nuts (7) box-end wrench.
TA244166
2-729
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
12. Fuel gage (1) Two wires (2), two a. Put wires in correct position.
new lockwashers (3), b. Screw in and tighten using 5/16-incl
and two nuts (4) box-end wrench.
c. Get rid of tags.
NOTE
FOLLOW-ON MAINTENANCE:
AMMETER
TA244167
2-730
TM 5-3805-254-20-2
AMMETER - CONTINUED
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
TA244168
2-731
TM 5-3805-254-20-2
AMMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
2-732
TM 5-3805-254-20-2
AMMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
11. Wire (7), two new a. Screw on and tighten using 318-inch
lockwashers (6), and box-end wrench.
two nuts (5) b. Get rid of tags.
12. Wire (4), new lock- a. Screw on and tighten using 5/16-inch
washer (3), and box-end wrench.
nut (2) b. Get rid of tags.
NOTE
FOLLOW-ON MAINTENANCE:
TA244169
2-733
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
5. Glow plug switch (1) Two screws (3) Screw in and tighten using number one
cross-tip screwdriver.
2-734
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA244170
2-735
TM 5-3805-254-20-2
INITIAL SETUP:
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
2-736
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
6. Engine compression Nut (6) Screw on completely and then unscrew one
brake switch (1) turn.
NOTE
FOLLOW-ON MAINTENANCE:
TA244171
2-737
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
3. Instrument panel (5) Engine start Carefully move back behind right instrument
button (1) panel (6).
4. Engine start Two nuts (7), two a. Tag wires (page 2-424).
button (1) lockwashers (8), and b. Using 5/16-inch box-end wrench, un-
three wires (9) screw and take off.
c. Get rid of lockwashers.
2-738
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
7. Engine start New lockwasher (4) Screw on and tighten using 3/4-inch box-
button (1) and nut (3) end wrench.
TA244172
2-739
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
KEY SWITCH
INITIAL SETUP:
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
2-740
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
2. Key switch (1) Nut (3) Using 1 18-inch open-end wrench, un-
screw and take off.
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
5. Key switch (1) Nut (3) Screw in and tighten using 1 118-inch open-
end wrench.
TA244173
2-741
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
2-742
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
6. Headlight beam Two screws (5) and Screw in and tighten using number three
selector switch (3) two new lock- cross-tip screwdriver.
washers (6)
NOTE
TA244174
2-743
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
4. Instrument panel (6) Screw (7), flat Using two 9/16-inch open-end wrenches,
washer (9), clamp unscrew and take out.
(10), and nut (11)
5. Steering column (1) Turn signal switch a. Using number one cross-tip screw-
(12), bracket (13), driver, unscrew and take out.
three screws (14), b. Get rid of lockwashers.
and three lock-
washers (15)
2-744
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
7. Turn signal Bracket (13) and Using number one cross-tip screwdriver,
switch (12) two screws (18) unscrew and take off.
TA244175
2-745
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
8. Turn signal Bracket (2) and Screw in and tighten using number one
switch (1) two screws (3) cross-tip screwdriver.
10. Steering column (7) Turn signal switch Screw in and tighten using number one
(1), bracket (2), cross-tip screwdriver.
three screws (8),
and three new
lockwashers (9)
11. Instrument Screw (11), flat Screw in and tighten using two 9/16-inch
panel (10) washer (12), clamp open-end wrenches.
(13), and nut (14)
12. Instrument Jamnut (15) Screw on and tighten using two 9/16-inch
panel (10) and open-end wrenches.
screw (11)
2-746
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
TA2441 76
2-747
TM 5-3805-254-20-2
INITIAL SETUP
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
2-748
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad, to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Two flat washers (5) Screw on and tighten using 3/8-inch box-
and two nuts (4) end wrench.
T244177
2-749
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
2-750
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 318-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244178
2-751
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wires (page 2-424).
and two wires (3) b. Using 318-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-752
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 3/8-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244179
2-753
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
2-754
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 318-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244180
2-755
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wires (page 2-424).
and two wires (3) b. Using 318-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-756
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 3/8 inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244181
2-757
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wires (page 2-424).
and two wires (3) b. Using 3/8-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-758
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 3/8-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244182
2-759
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wire (page 2-424).
and wire (3) b. Using 3/8-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-760
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 318-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244183
2-761
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wire (page 2-424).
and wire (3) b. Using 318-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-762
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 3/8-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244184
2-763
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
1. Circuit breaker (1) Self-locking nut (2) a. Tag wires (page 2-424).
and two wires (3) b. Using 3/8-inch box-end wrench, un-
screw and take off.
c. Get rid of self-locking nut.
2-764
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind right instrument panel pad to prevent breaking or disconnecting wires.
5. Circuit breaker (1) Flat washer (6), two Screw on and tighten using 3/8-inch box-
new lockwashers (5), end wrench.
and two nuts (4)
TA244185
2-765
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
FUSE BLOCK
INITIAL SETUP
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
2-766
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244186
2-767
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
9. Fuse block (1) Two screws (4) Screw in and tighten using number two
cross-tip screwdriver.
TA244187
2-768
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-769
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
1. Mounting Two screws (2), two a. Using two 7/16-inch box-end wrenches,
bracket (1) lockwashers (3), and unscrew and take out.
two nuts (4) b. Get rid of lockwashers.
2. Circuit breaker (5) Rubber boot (6) Pull off and slide back.
INSTALLATION
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
6. Circuit breaker (5) Two wires (7), two a. Put wires in correct position.
screws (8), and two b. Screw in and tighten using 38-inch flat-
new lockwashers (9) tip screwdriver.
c. Take off tags.
d. Get rid of tags.
8. Mounting Two screws (2), two Screw in and tighten using two 7116-inch
bracket (1) new lockwashers (3), box-end wrenches.
and two nuts (4)
2-770
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools Materials/Parts
TA244188
2-771
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Junction box (1) Two wingscrews (2) Unscrew and take out.
and cover (3)
3. Firewall (6) Two screws (7), two Using number two cross-tip screwdriver,
cover mounting unscrew and take out.
brackets (8), and
junction box (1)
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-772
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
7. Firewall (6) Junction box (1), Screw in and tighten using number two
two cover mounting cross-tip screwdriver.
brackets (8), and
two screws (7)
8. Junction box (1) Thirty wires (4) a. Put wires in place. See table below.
and sixteen new b. Screw on and tighten using 3/8-inch
self-locking nuts (5) box-end wrench.
c. Take off tags.
d. Get rid of tags.
TA244189
2-773
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Junction box (1) Two wingnuts (2) Unscrew and take off.
and cover (3)
2-774
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
3. Junction box (1) Two wires (6) a. Tag wires (page 2-424).
and nut (7) b. Using 7/16-inch box-end wrench, un-
screw and take off.
4. Firewall (8) Two nuts (9) and Using 7/16-inch open-end wrench and
junction box (1) 7/16-inch box-end wrench, unscrew and
take off.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244190
2-775
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
9. Junction box (2) Two wires (4) a. Put wires in place. See table below.
and nut (5) b. Screw on and tighten using 7/16-inch
box-end wrench.
c. Take off tags.
d. Get rid of tags.
2-776
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-777
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Junction box (1) Two wingnuts (2) Unscrew and take off.
and cover (3)
4. Firewall (8) Two nuts (9) and Using 7116-inch open-end wrench and
junction box (1) 7/16-inch box-end wrench, unscrew and
take off.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
2-778
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Junction box (1) Two wires (6) and a. Put wires in place.
nut (7) b. Screw on and tighten using 7/16-inch
box-end wrench.
c. Take off tags.
d. Get rid of tags.
10. Nine wires (4) a. Put wires in place. See table below.
and eight new b. Screw on and tighten using 7/16-inch
self-locking nuts (5) box-end wrench.
c. Take off tags.
d. Get rid of tags.
TA244192
2-779
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Driver seat valve Line nut (2) and Using 9/16-inch open-end wrench, un-
assembly (1) air line (3) screw and take off.
2. Left lower rear Eight screws (5) Using number two cross-tip screwdriver,
molding (4) and eight flat unscrew and take out.
washers (6)
3. Left side rear cab Air line (3) and a. Push air line through hole in molding.
wall (7) left lower rear b. Take out molding.
molding (4)
2-780
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Junction box (8) Nineteen wires (9) a. Tag wires (page 2-424).
and twelve self- b. Using 3/8-inch box-end wrench, un-
locking nuts (10) screw and take off.
c. Get rid of self-locking nuts.
5. Junction box Two nuts (12) and Using 7/16-inch box-end wrench, unscrew
support (11) junction box (8) and take off.
TA244193
2-781
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
8. Junction box Junction box (1) a. Put junction box in place. See table
support (2) and two nuts (3) below.
b. Screw on and tighten using 7116-inch
box-end wrench.
10. Left side rear cab Air line (7) and a. Push air line through hole in molding.
wall (6) left lower rear b. Put molding in place.
molding (8)
11. Left lower rear Eight flat washers Screw in and tighten using number two
molding (8) (9) and eight cross-tip screwdriver.
screws (10)
12. Driver seat valve Air line (7) and a. Put line in place.
assembly (11) line nut (12) b. Screw on and tighten using 9/16-inch
open-end wrench.
2-782
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
2-783
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Driver seat valve Line nut (2) and Using 9/16-inch open-end wrench, un-
assembly (1) air line (3) screw and take off.
2. Left lower rear Eight screws (5) Using number two cross-tip screwdriver,
molding (4) and eight flat unscrew and take out.
washers (6)
3. Left side rear cab Air line (3) and a. Push air line through hole in molding.
wall (7) left lower rear b. Take out molding.
molding (4)
4. Junction box (8) Eleven wires (9) and a. Tag wires (page 2-424).
eight self-locking b. Using 3/8-inch box-end wrench, un-
nuts (10) screw and take off.
c. Get rid of self-locking nuts.
5. Junction box Two nuts (12) and Using 7/16-inch box-end wrench, unscrew
support (11) junction box (8) and take off.
2-784
TM 5-3805-254-20-2
TA244195
2-785
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
9. Junction box (1) Eleven wires (4) a. Put wires in place. See table below.
and eight new b. Screw on and tighten using 3/8-inch
self-locking nuts (5) box-end wrench.
c. Take off tags.
d. Get rid of tags.
10. Left side rear Air line (7) and a. Push air line through hole in molding.
cab wall (6) left lower rear b. Put molding in place.
molding (8)
11. Left lower rear Eight flat washers Screw in and tighten using number two
molding (8) (9) and eight cross-tip screwdriver.
screws (10)
12. Driver seat valve Air line (7) and a. Put line in place.
assembly (11) line nut (12) b. Screw on and tighten using 9/16-inch
open-end wrench.
2-786
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
2-787
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
DISASSEMBLY
2-788
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244197
2-789
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
9. Stoplight/taillight Backup lamp (2) a. Aline pins on lamp with slots in stoplight/
assembly (1) taillight assembly.
b. Push in, turn clockwise, and release.
10. Tail, turn, and a. Aline pins on lamp with slot in stoplight/
stop lamp (3) taillight assembly.
b. Push in, turn clockwise, and release.
If lamp will not turn, take out, turn 180
degrees, and repeat a and b.
INSTALLATION
NOTE
Taillight and bracket mating surfaces must be free of paint, dirt, and grease to ensure proper ground.
13. Stoplight/ Seven wires (10) a. Put wires in correct position and push
taillight (1) on.
b. Take off tags.
c. Get rid of tags.
2-790
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
TA244198
2-791
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
DISASSEMBLY
INSPECTIONIREPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-792
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
9. Stoplight/taillight Backup lamp (12) a. Aline pins on lamp with slot in stoplight/
assembly (1) taillight assembly.
b. Push in, turn clockwise, and release.
10. Tail, turn, and a. Aline pins on lamp with slot in stoplight/
stop lamp (11) taillight assembly.
b. Push in, turn clockwise, and release.
If lamp will not turn, take out, turn 180
degrees, and repeat a and b.
TA244199
2-793
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Stoplight/taillight assembly and bracket mating surfaces must be free of paint, dirt, and grease to ensure proper
ground.
13. Stoplight/taillight Three wires (5) a. Put wires in correct position and push
assembly (2) on.
b. Take off tags.
c. Get rid of tags.
2-794
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for both left and right front turn signals.
1. Front fender (1) Four nuts (2), four a. Using two 1/2-inch open-end
lockwashers (3), four wrenches, unscrew and take off.
flat washers (4), b. Get rid of lockwashers.
two screws (5), and
clamp (6)
TA244201
2-795
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
DISASSEMBLY
10. Marker lamp (16) Push in, turn counterclockwise and take
out.
INSPECTIONIREPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-796
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
13. Turn signal (1) Marker lamp (16) a. Aline pins on lamp with slot in turn
signal.
b. Push in, turn clockwise and release.
TA244202
2-797
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
16. Turn signal (1) Red lens (2), new a. Put gasket in place.
gasket (3), and b. Put lens in place.
four screws (4) c. Screw in and tighten using number one
cross-tip screwdriver.
TA244203
2-798
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for both left and right front turn signals.
20. Front fender (10) Turn signal (1) Put in place and hold.
and guard (9)
2-799
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
Gasket, lens
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for both left and right front marker lights.
1. Turn signal (1) Four screws (2), a. Using number one cross-tip screw-
lens (3), and driver, unscrew and take out.
gasket (4) b. Get rid of gasket.
INSPECTION/REPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-800
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for both left and right front marker lights.
6. Turn signal (1) Marker lamp (5) a. Aline pins on lamp with slot in turn
signal.
b. Push in, turn clockwise and release.
TA244205
2-801
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
Gasket, lens
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for both marker lights and clearance lights.
1. Cab ceiling (1) Cover (2) and Using number one cross-tip screwdriver,
six screws (3) unscrew and take out.
7. Marker light Rear screw (11) Using number two cross-tip screwdriver,
body (5) unscrew and take out.
2-802
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Marker light Front screw (12) Using number two cross-tip screwdriver,
body (5) unscrew and take out.
10. Cab roof (10) Marker light body Pull up and take out.
(5), pad (13), and
wire (14)
TA244206
2-803
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
NOTE
Steps given are typical for both marker lights and clearance lights.
14. Cab roof (3) Marker light body a. Put wire through hole in pad.
(2), pad (4), and b. Put wire through hole in roof.
wire (5) c. Put marker light in place.
18. Marker light Front screw (10) Screw in and tighten using number two
body (1) cross-tip screwdriver.
20. Marker light Rear screw (11) Screw in and tighten using number two
body (1) cross-tip screwdriver.
21. Cab roof (3) Marker light body a. Bend light into position.
(1) and adjustment b. Tighten adjustment screw using 3/16-
screw (12) inch flat-tip screwdriver.
2-804
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
22. Marker light Lamp (13) a. Aline pins on lamp with slots in marker
body (1) light body.
b. Push in, turn clockwise and release.
2-805
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
1. Dump body (1) Marker light (2) Using 3/16-inch flat-tip screwdriver, pry
out.
INSTALLATION
NOTE
2-806
TM 5-3805-254-20-2
HEADLIGHT ASSEMBLY
INITIAL SETUP
Tools Materials/Parts
TA244208
2-807
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Use care when removing damaged headlight assembly, broken glass or sharp metal could cut you.
NOTE
Steps given are typical for both left and right headlight assemblies.
1. Fender (1) Bezel (2) and a. Using number one cross-tip screw-
screw (3) driver, unscrew and take out screw.
b. Lift up and take off bezel.
NOTE
Hold retaining ring, lamp, and adjustment basket in place when performing step 2.
2. Ring (4) Spring (5) Using 6-inch longnose pliers, unhook and
take off.
3. Fender basket (6) Ring (4), lamp (8), a. Lift up from fender basket recess.
and two adjustment and adjustment b. Take out and hold.
screws (7) basket (9) c. Lift up and take off retaining ring.
4. Connector (10) Lamp (8) and ad- a. Pull apart and take out lamp.
justment basket (9) b. Take out adjustment basket.
6. Fender basket (6) Harness (13) Using 3/16-inch flat-tip screwdriver, pry
out.
2-808
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8. Fender (1) Four screws (14), a. Using number one cross-tip screw-
fender basket (6), driver, unscrew and take out.
and gasket (15) b. Get rid of gasket.
TA244209
2-809
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
10. Fender basket (4) Spring (5) a. Look for loose rivet.
b. Look for straightened or broken coils.
13. Adjustment Adjustment tabs (8) Look for bends, breaks or corrosion.
basket (3) and tongue (9)
14. Harness (10) Grommet (11) Look for cracks, tears or worn groove.
15. Two connectors (12) Look for cracks, breaks or corroded ends.
and (13)
INSTALLATION
NOTE
Steps given are typical for both left and right headlight assemblies.
2-810
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
16. Fender (14) New gasket (15), Screw in and tighten using number one
fender basket (4), cross-tip screwdriver.
and four screws (16)
17. Fender basket (4) Two adjustment Screw in five turns using number one cross-
screws (7) tip screwdriver.
TA244210
2-811
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
21. Adjustment basket Ring (3) Aline tongue of adjustment basket with slot of
(1) and lamp (2) ring, push down and snap in place.
22. Fender basket (4) Ring (3), lamp (2), Put adjustment basket tabs into adjustment
and two adjustment and adjustment screw slots, push down and hold.
screws (5) basket (1)
24. Fender (7) Bezel (8) a. Put tongue of bezel into slot of fender
and screw (9) basket (4), push down and hold.
b. Screw in and tighten using number one
cross-tip screwdriver.
ALINEMENT
NOTE
This procedure should only be performed when alinement tool or screen is not available.
Headlight alinement must be performed on level surface with wall at one end and in
shaded area.
TA244211
2-812
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
The purpose of steps 25, 26, and 27 is to make sure that both left and right headlights are
equally 25 feet (7.6 meters) from wall or screen.
25. Level area Floor (11) a. Using chalk, make mark (12) where wall
and wall (10) meets floor.
b. Using 50-foot tape measure and chalk,
measure 6 feet 5 1/2 inches (1.97 m) to
left of mark (12) and make mark (13)
where wall meets floor.
c. Using carpenter’s square, 50-foot tape
measure and chalk, measure straight
out from mark (13) 27 feet 11 1/2 inches
(8.52 m) on floor and draw line (14).
d. Make mark (15) at end of line (14).
e. Using carpenter’s square, 50-foot tape
measure and chalk, measure straight
out from mark (12) 27 feet 11 1/2 inches
(8.52 m) on floor and draw line (16).
f. Make mark (17) at end of line (16).
g. Using 50-foot tape measure and chalk,
draw line (18) between mark (15) and
mark (17) and extend line (18) 3 feet
(.91 m) at both ends.
TA244212
2-813
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ALINEMENT - CONTINUED
NOTE
26. Lines (1, 2, and 3) Truck (4) Using lines (1 and 2) to guide driver, park
truck so the center of each front wheel is
directly over line (3) and tires are evenly
placed on lines (1 and 2).
27. Wall (5) Lamps (6 and 7) Using 50-foot tape measure, check dis-
tance between lamps and wall.
Move truck to plus or minus 1/2-inch
(1.27 cm).
28. Truck (4) Ten tires (8) Check for correct inflation (page 1-20).
29. Wall (5) Lines (9 and 10) a. Using chalk and carpenter’s square,
draw lines (9 and 10) 3-feet 9 1/4-
inches (1.15 m) straight up from marks
(11 and 12) and make marks (13 and
14) at end of lines (9 and 10).
b. Using chalk and 50-foot tape measure,
extend lines (9 and 10) 1-foot (.3 m).
30. Line (15) Using chalk and 50-foot tape measure, draw
line (15) between marks (13 and 14) and
extend 1-foot (.3 m) at both ends.
2-814
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
32. Cab floor (18) Headlight selector Push in and release to select highbeam.
switch (19)
TA244213
2-815
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ALINEMENT - CONTINUED
33. Under right Connector (2) Pull apart to disconnect lamp (3).
fender (1)
34. Left fender Bezel (5) and a. Using number one cross-tip screw-
basket (4) screw (6) driver, unscrew and take out screw.
b. Lift up and take off bezel.
35. Wall (7) Two adjustment Using number one cross-tip screwdriver,
screws (8) turn until center of brightest part of headlight
is where lines (9 and 10) cross.
37. Left fender Bezel (5) and a. Put tongue of bezel into slot of fender
basket (4) screw (6) basket, push down and hold.
b. Screw in and tighten using number one
cross-tip screwdriver.
TA244214
2-816
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
38. Under left Connector (12) Pull apart to disconnect lamp (13).
fender (11)
39. Right fender Bezel (15) and a. Using number one cross-tip screw-
basket (14) screw (16) driver, unscrew and take out screw.
b. Lift up and take off bezel.
40. Wall (17) Two adjustment Using number one cross-tip screwdriver,
screws (18) turn until center of brightest part of headlight
is where lines (19 and 20) cross.
42. Right fender Bezel (15) and a. Put tongue of bezel into slot of fender
basket (14) screw (16) basket, push down and hold.
b. Screw in and tighten using number one
cross-tip screwdriver.
TA244215
2-817
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ALINEMENT - CONTINUED
43. Cab floor (1) Headlight selector Push in and release to select lowbeam.
switch (2)
2-818
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
2-819
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with
batteries. Failure to observe this precaution could cause serious injury to personnel.
Do not smoke, use open flame, or allow sparks near batteries. Mixture of oxygen and
hydrogen gases released from batteries is highly flammable and can explode causing
injury to personnel.
NOTE
1. Two hooks (1) Two latches (2) Lift up and take off.
4. Post (8) Terminal (5) Using battery terminal puller, pull off.
6. Post (12) Terminal (9) Using battery terminal puller, pull off and
and cable (13) take out.
DISASSEMBLY
NOTE
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can
injure personnel and cause damage to equipment. Refer to TM 9-247.
2-820
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
2-821
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
Steps given are typical for both battery positive-to-negative connector cables.
ASSEMBLY
NOTE
15. Cable (1) Two terminals (2 Screw in and tighten using two 9/16-inch
and 3), two screws open-end wrenches.
(4), and two
nuts (5)
16. Two terminals Two screws (6) Screw in two turns using two 1/2-inch open-
(2 and 3) and two nuts (7) end wrenches.
Do not tighten.
INSTALLATION
NOTE
2-822
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
19. Cable (1) and two Two screws (6) Screw in and tighten using two 1/2-inch
terminals (2 and 3) and two nuts (7) open-end wrenches.
20. Two batteries (10) Two posts (8 and 9) Apply GAA grease.
and two terminals
(2 and 3)
22. Two hooks (13) Two latches (14) Lift up, put in place and release.
NOTE
TA244218
2-823
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with
batteries. Failure to observe this precaution could cause serious injury to personnel.
Do not smoke, use open flame, or allow sparks near batteries. Mixture of oxygen and
hydrogen gases released from batteries is highly flammable and can explode causing
injury to personnel.
REMOVAL
1. Two hooks (1) Two latches (2) Lift up and take off.
3. Left frame Cable (6), screw Using 3/4-inch 1/2-inch drive socket, 6-
rail (5) (7), and nut (8) inch extension, ratchet handle and 3/4-inch
box-end wrench, unscrew and take off.
2-824
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5. Post (12) Terminal (9) Using battery terminal puller, lift up and take
off.
7. Post (16) Terminal (13) Using battery terminal puller, lift up and take
and cable (6) out.
TA244219
2-825
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
8. Two terminals (1) Two screws (2) and Using two 1/2-inch open-end wrenches,
two nuts (3) unscrew and take out.
9. Two cables (4) Two terminals (1), Using two 9/16-inch open-end wrenches,
two screws (5), unscrew and take out.
and two nuts (6)
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can
injure personnel and cause damage to equipment. Refer to TM 9-247.
NOTE
WARNING
Safety goggles must be worn when using wire brush. Flying rust or metal particles could
cause eye injury.
13. Left frame Cable ground a. Using pocket knife, scrape clean.
rail (8) area (9) b. Using wire brush, clean.
2-826
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
14. Two terminals (1) Look for cracks, breaks or corroded mating
surfaces.
15. Two cables (4) Look for corroded ends or worn cable
coverings.
ASSEMBLY
17. Two cables (4) Two terminals (1), Screw in and tighten using two 9/16-inch
two screws (5), open-end wrenches.
and two nuts (6)
18. Two terminals (1) Two screws (2) Screw in two turns using two 1/2-inch open-
and two nuts (3) end wrenches.
Do not tighten.
TA244220
2-827
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
20. Two terminals (1) Two screws (2) a. Screw in and tighten using two 1/2-inch
and two nuts (3) open-end wrenches.
b. Apply GAA grease.
21. Left frame Cable (4), screw Screw in and tighten using 3/4-inch 1/2-
rail (8) (9), and nut (10) inch drive socket, 6-inch extension, ratchet
handle, and 3/4-inch box-end wrench.
23. Two hooks (13) Two latches (14) Lift up, put in place, and release.
TA244221
2-828
TM 5-3805-254-20-2
INITIAL SETUP
2-829
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with
batteries. Failure to observe this precaution could cause serious injury to personnel.
Do not smoke, use open flame, or allow sparks near batteries. Mixture of oxygen and
hydrogen gases released from batteries is highly flammable and can explode causing
injury to personnel.
1. Two hooks (1) Two latches (2) Lift up and take off.
4. Post (8) Terminal (5) Using battery terminal puller, pull off.
TA244222
2-830
TM 5-3805-254-20-2
BATTERY POSITIVE CABLE - CONTINUED
ACTION
LOCATION ITEM REMARKS
NOTE
5 Bracket (13) Two screws (14), two a Using two 7116-inch box-end wrenches,
nuts (15), two lock- unscrew and take out.
washers (16), and b Get rid of lockwashers.
four clamps (17)
2-831
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
8 Two terminals (1) Two screws (2) Using two 1/2-inch open-end wrenches,
and two nuts (3) unscrew and take out.
9 Two cables (4) Two terminals (1), Using two 9/16-inch open-end wrenches,
two screws (5), unscrew and take out.
and two nuts (6)
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and cause
damage to equipment Refer to TM 9-247.
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-832
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244224
2-833
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
21 Two terminals (3) Two screws (6) Screw in two turns, using two 1/2-inch
and two nuts (7) open-end wrenches.
Do not tighten.
INSTALLATION
NOTE
TA244663
2-834
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244225
2-835
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
CAUTION
Do not overtighten terminals, failure to observe this precaution could cause damage to terminals or posts.
26 Terminal (2) Screw (3) Screw in and tighten using two 1/2-inch
and nut (4) open-end wrenches.
29 Terminal (7) Screw (8) Screw in and tighten using two 1/2-inch
and nut (9) open-end wrenches.
32 Two hooks (13) Two latches (14) Lift up, put in place and release.
2-836
TM 5-3805-254-20-2
NOTE
TA244226
2-837
TM 5-3805-254-20-2
STORAGE BATTERIES
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with batteries Failure to observe this
precaution could cause serious injury to personnel.
Do not smoke, use open flame, or allow sparks near batteries Mixture of oxygen and hydrogen gases released from
batteries is highly flammable and can explode causing injury to personnel.
TESTING
Change 1 2-838
TM 5-3805-254-2.2
ACTION
LOCATION ITEM REMARKS
REMOVAL
2 Two battery hold- Two nuts (3), Using 9/16-inch, box-end wrench, un-
down bolts (2) two gaskets (4), screw and take off.
and two flat
washers (5)
TA244227
2-839
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-840
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
WARNING
Do not smoke, use open flame, or allow sparks near batteries Mixture of oxygen and hydrogen gases released from
batteries is highly flammable and can explode causing serious injury or death.
12 Battery tray (1) Four storage Put in place using storage battery
batteries (3) carrier.
15 Two battery hold- Two nuts (6), two Screw on and tighten using 9/16-inch
down bolts (4) gaskets (7), and two box-end wrench.
flat washers (8)
NOTE
FOLLOW-ON MAINTENANCE: Connect battery cables (page 2-424)
TA244228
2-841
TM 5-3805-254-20-2
BATTERY BOX
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Rubber apron, safety gloves, and safety goggles must be worn when working with batteries Failure to observe
this precaution could cause serious injury.
2-842
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
1 Frame rail (1) Battery box (2) a Using weak solution of bicarbonate
soda, water, and wiping rags, clean.
b Using wiping rags, dry.
2 Battery box (2) Six screws (3) and Using 314-inch box-end wrench, and 3/4-
six nuts (4) inch open-end wrench, unscrew and take
out.
WARNING
Due to excessive weights, assistance will be needed to support battery box, to prevent personal injury.
2-843
TM 5-3805-254.20-2
BATTERY BOX - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
NOTE
4 Frame rail (1) Two screws (2), two a Using 314-inch box-end wrench and
nuts (3), and front 3/4-inch open-end wrench, unscrew
bracket (4) and take out.
b Take off front bracket.
NOTE
TA244230
2-844
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
NOTE
6 Battery box (9) Four screws (10), a Using 9116-inch, 1/2-inch drive
four lockwashers socket and ratchet handle and 9116-inch
(11), four nuts (12), box-end wrench, unscrew and take off.
and four support b Get rid of lockwashers.
straps (13) c Take off support straps.
TA244231
2-845
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY - CONTINUED
8 Battery box (1) Screw (2), lock- a Using 9/16-inch, 1/2-inch drive socket
washer (3), nut (4), and ratchet handle and 9/16-inch box-
and side panel (5) end wrench, unscrew and take off.
b Get rid of lockwasher.
c Take off side panel.
9 Side panel (5) Two nuts (6), two a Using 318-inch open-end wrench, un-
lockwashers (7), and screw and take off.
battery retainer (8) b Get rid of lockwashers.
c Take off battery retainer.
10 Battery box (1) Three screws (9), a Using 9/16-inch, 1/2-inch drive socket
three lockwashers and ratchet handle and 9/16-inch box-
(10), three nuts end wrench, unscrew and take off.
(11), and side b Get rid of lockwashers.
panel (12) c Take off side panel.
11 Side panel (12) Two nuts (13), two a Using 3/8-inch open-end wrench,
lockwashers (14), unscrew and take off.
and battery b Get rid of lockwashers.
retainer (15) c Take off battery retainer.
12 Center panel (16) Two trays (17) and a Using 9/16-inch, 112-inch drive socket
(18), three screws and ratchet handle and 9/16-inch box-
(19), three lock- end wrench, unscrew and take off.
washers (20), and b Get rid of lockwashers.
three nuts (21) c Take apart two trays and center
panel (16).
2-848
TM 5-3805-254-20-2
TA244232
2-847
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY - CONTINUED
13 Cover (1) Four nuts (2), four a Using 1/2-inch open-end wrench, un-
lockwashers (3), and screw and take off.
upper step (4) b Get rid of lockwashers.
c Take off upper step.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get
medical aid immediately.
TA244233
2-448
TM 5-3805-254-20.2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
16 Cover (1) and Clean, using liquid detergent with water and
two battery wiping rags.
retainers (9)
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
18 Two side panels (10) Two hooks (11) Pull up and check for spring tension and
release.
Hook should be under spring tension
and return when released.
TA244234
2-849
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT- CONTINUED
ASSEMBLY
TA244235
2-850
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
Position trays with five holes towards center panel Position center panel as shown.
23 Center panel (9) Two trays (10) and a Aline center panel and two trays.
(11), three screws b Screw in and tighten using 9/16-inch,
(12), three new 112-inch drive socket and ratchet handle
lockwashers (13), and 9116-inch box-end wrench.
and three nuts (14)
TA244236
2-581
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
NOTE
NOTE
TA244237
2-852
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
NOTE
TA244238
2-853
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
NOTE
NOTE
2-854
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
If battery box mounting brackets were removed perform steps 30 and 31.
TA244240
2-855
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
WARNING
Due to excessive weight, assistance will be needed to support battery box to prevent personal injury.
32 Three brackets (1) Battery box (2), a With assistance put on.
three screws (3), b Screw on and tighten, using 314-inch
and three nuts (4) box-end wrench and 3/4-inch open-end
wrench.
33 Six screws (5) and Screw on and tighten, using 3/4-inch box-
three nuts (6) end wrench and 3/4-inch open-end
wrench.
NOTE
FOLLOW-ON MAINTENANCE:
2-856
TM 5-3805-2520-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
INSTALLATION
4 Optical light Socket (2) a Aline tabs (4) on socket with slots (5) on
assembly (1) light assembly.
b Put in and turn clockwise.
TA244242
2-857
TM 5-3805-2520-2
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
2 Lower instrument Two screws (4) and a Using number one cross-tip screw-
panel (3) bracket (5) driver, unscrew and take out.
b Take off bracket.
DISASSEMBLY
3 Bracket (5) and Screw (6), flat a Using 3/16-inch flat-tip screwdriver and
optical light washer (7), lock- 1/4-inch box-end wrench, unscrew and
assembly (1) washer (8), and take off.
nut (9) b Get rid of lockwasher.
2-858
TM 5-3805-254-20-2
OPTICAL LIGHT ASSEMBLY - CONTINUED
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
INSTALLATION
6 Optical light Socket (2) a Aline tabs (10) on socket with slots (11)
assembly (1) on optical light assembly.
b Put in and turn clockwise.
NOTE
FOLLOW-ON MAINTENANCE:
2-859
TM 5-3805-254-20-2
RIGHT INSTRUMENT PANEL OPTICAL RIBBON
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for removal of four identification tabs from four bezels.
1 Rear of instrument Bezel (2) and iden- a Using 1/8-inch flat-tip screwdriver, pry
panel (1) tification tab (3) rear of bezel back and take out identifi-
cation tab.
b Take out bezel.
c Repeat step a until all four identification
tabs and bezels have been removed.
2 Lower center instru- Power take off a Using two 7/16-inch box-end wrenches,
ment panel (4) control (5), two unscrew and take off.
screws (6), two b Take off power take off control.
flat washers (7), Do not remove screws from lower
two lockwashers (8), center instrument panel.
and two nuts (9) c Get rid of lockwashers.
2-860
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Optical light Optical ribbon (13) Using 1/4-inch, flat-tip screwdriver, lift up
assembly (12) plastic tab and pull out optical ribbon.
TA244244
2-861
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for the installation of four identification tabs into four bezels.
When installing optical ribbon be sure to start at end farthest away from optical light assembly.
7. Lower center instru- Two screws (7) and a. Put bracket in place.
ment panel (6) bracket (8) b. Screw in and tighten using number one
cross-tip screwdriver.
TA244245
2-862
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA244245
2-863
TM 5-3805-254-202
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for removal of three identification tabs from three bezels.
1. Rear of instrument Bezel (2) and iden- a. Using 1/8-inch flat-tip screwdriver, pry
panel (1) tification tab (3) rear of bezel back and take out identifi-
cation tab.
b. Take out bezel.
c. Repeat step a until all three identification
tabs and bezels have been removed.
2. Lower center instru- Power take off a. Using two 7/16-inch box-end wrenches,
ment panel (4) control (5), two unscrew and take off.
screws (6), two flat b. Take off power take off control.
washers (7), two Do not remove screws from lower
lockwashers (8), and center instrument panel.
two nuts (9) c. Get rid of lockwashers.
2-864
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Optical light Optical ribbon (13) Using 1/4-inch flat-tip screwdriver, lift up
assembly (12) plastic tab and pull out optical ribbon.
TA244245
2-865
TM 5-3805-254-20-2
LOWER INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for the installation of three identification tabs into three bezels.
When installing optical ribbon be sure to start at end farthest away from optical light assembly.
7. Lower center instru- Two screws (7) and a. Put bracket in place.
ment panel (6) bracket (8) b. Screw in and tighten using number one
cross-tip screwdriver.
TA244248
2-866
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8. Power take off con- a. Put power take off control in place.
trol (9), two screws b. Screw in and tighten using two 7/16-
(10), two flat wash- inch box-end wrenches.
ers (11), two new
lockwashers (12), and
two nuts(1
NOTE
FOLLOW-ON MAINTENANCE:
TA244249
2-867
TM 5-3805254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Step 1 is typical for removal of three identification tabs from three bezels.
1. Rear of instrument Bezel (2) and iden- a. Using 1/8-inch flat-tip screwdriver, pry
panel (1) tification tab (3) rear of bezel back and take out identi-
fication tab.
b. Take out bezel.
c. Repeat step a until all three identification
tabs and bezels have been removed.
2. Lower center instru- Power take off a. Using two 7116-inch box-end wrenches,
ment panel (4) control (5), two unscrew and take off.
screws (6), two flat b. Take off power take off control.
washers (7), two Do not remove screws from lower
lockwashers (8), and center instrument panel.
two nuts (9) c. Get rid of lockwashers.
2-868
TM 5-3805-254-20-2
LEFT INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
4. Optical light Optical ribbon (13) Using 114-inch flat-tip screwdriver, lift up
assembly (12) plastic tab and pull out optical ribbon.
TA244245
2-869
TM 5-3805-254-20-2
LEFT INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Step 5 is typical for installation of three identification tabs into three bezels.
When installing optical ribbon be sure to start at end farthest away from optical light assembly.
7. Lower center instru- Two screws (7) and a. Put bracket in place.
ment panel (6) bracket (8) b. Screw in and tighten using number one
cross-tip screwdriver.
TA244251
2-870
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA244252
2-871
TM 5-3805-254-20-2
INITIAL SETUP
(two required)
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Cover plate (1) to Six screws (3) Using number one cross-tip screwdriver,
front trim panel unscrew and take out.
head retainer (2)
Steps given are typical for removal of two identification tabs from two bezels.
3. Cover plate (1) Bezel (4) and iden- a. Using 118-inch flat-tip screwdriver, pry
tification tab (5) rear of bezel back and take out identifi-
cation tab.
b. Take out bezel.
c. Repeat step a until two identification tabs
and bezels have been removed.
2-872
TM 5-3805-254-20-2
UPPER INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
4. Optical ribbon (6) Two identification a. Using 5-inch scissors cut off.
tabs (5) b. Tape new optical ribbon to old optical
ribbon.
5. Lower center instru- Power take off a. Using two 7/16-inch box-end
wrenches,
ment panel (7) control (8), two unscrew and take off.
screws (9), two b. Take off power take off control.
flat washers (10), Do not remove screws from lower
two lockwashers (11), center instrument panel.
and two nuts (12) c. Get rid of lockwashers.
TA244253
2-873
TM 5-3805-254-20-2
UPPER INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
6. Lower center instru- Two screws (2) a Using number one cross-tip screw-
ment panel (1) bracket (3) driver, unscrew and take out.
b. Take out bracket.
7. Optical light Optical ribbon (5) Using 114-inch flat-tip screwdriver, lift up
assembly (4) plastic tab and pull out optical ribbon.
CAUTION
Care must be taken when pulling optical ribbon through tube to prevent damage or breaking.
8. Tube (6) Optical ribbon (7) Pull through until new optical ribbon comes
through.
CAUTION
Care must be taken when removing tape holding optical ribbons together, to prevent damage to new
optical ribbon.
9. Optical ribbon (7) Remove old optical ribbon from new optical
ribbon.
TA244254
2-874
TM 5-3805-254-20-2
UPPER INSTRUMENT PANEL OPTICAL RIBBON - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for installation of two identification tabs into two bezels.
10. Cover plate (8) Bezel (9) and iden- a. Put in place.
tification tab (10) b. Push identification tab into bezel.
c. Repeat step b until two identification tabs
are installed in bezels.
TA244245
2-875
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
12. Cover plate (2) to Six screws (3) Screw in and tighten using number one
front trim panel cross-tip screwdriver.
head retainer (1)
14. Lower center instru- Two screws (7) and a. Put bracket in place.
ment panel (6) bracket (8) b. Screw in and tighten using number one
cross-tip screwdriver.
TA244256
2-876
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools Materials/Parts
TA244257
2-877
TM 5-3805-254-202
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2. Support (4) Two screws (5), a. Using number three cross-tip screw-
automatic override driver, unscrew and take out two
module (1), and two screws.
flat washers (6) b. Take off automatic override module.
c. Take off two flat washers.
INSTALLATION
2-878
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
TA244258
2-879
TM 5-3805254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
CAUTION
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
2-880
TM 53805-254-20-2
NOTE
TA244259
2-881
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
NOTE
Steps given are typical for removal of five upper instrument panel gage lamps.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
Steps given are typical for installation of five upper instrument panel gage lamps.
2-882
TM 5-3805254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
TA244260
2-883
TM 5-3805-254-20-2
UPPER INSTRUMENT PANEL INDICATOR LAMPS - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
NOTE
Steps given are typical for removal of two upper instrument panel indicator lamps.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
Steps given are typical for installation of two upper instrument panel indicator lamps.
TA244245
2-884
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-885
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
FOLLOW-ON MAINTENANCE:
2-886
TM 264-20-2 2-887
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
NOTE
REMOVAL
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
2-887
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Personnel Required Equipment Condition
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
NOTE
Steps given are typical for removal of both turn signal indicator lamps.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
Steps given are typical for installation of both turn signal indicator lamps.
2-888
TM 5-3805254-20-2
TURN SIGNAL INDICATOR LAMPS - CONTINUED
ACTION
LOCATION ITEM REMARKS
NOTES
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Personnel Required Equipment Condition
TA244264
2-889
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
NOTE
Steps given are typical for removal of three right instrument panel gage lamps.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
Steps given are typical for installation of three right instrument panel gage lamps.
TA244265
2-890
TM 5-380525420-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-891
TM 5-3805-254.20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Care must be taken when removing lamp that is cracked or gray in color to prevent personal injury.
NOTE
Steps given are typical for removal of two right instrument panel indicator lamps.
2. Socket (2) Lamp (3) Push in, turn counterclockwise, and pull
out.
INSTALLATION
NOTE
Steps given are typical for installation of two right instrument panel indicator lamps.
2-892
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
TA244266
2-893
TM 5-3805-254-20-2
INITIAL SETUP
Screwdriver, cross-tip, number-one Left side cab door opened (page 2-424).
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
3 Socket (4) Lamp (5) Push in, turn counterclockwise, and pull
out.
INSTALLATION
4. Socket (4) Lamp (5) Put in place, push in, turn clockwise, and
release.
Care must be used when tightening screws. Overtightening screws can cause plastic position strip lens to
crack.
2-894
TM 5-3805.254-20-2
NOTE
TA244267
2-895
TM 5-3805-254-20-2
SLAVE RECEPTACLE
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Starter solenoid (1) Nut (2), lockwasher a. Using 3/4-inch box-end wrench, unscrew, and
(3), slave receptacle take off.
cable (4), and cable (5) b. Get rid of lockwasher.
3. Left splash plate Four nuts (11), a. Using two 1/2-inch box-end wrenches, unscrew,
(10) lockwashers (12), and and take out.
screws (13) b. Get rid of lockwashers.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-895.0
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702130 I
Change 1 2-895.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION _
7. Four screws (3), new Screw on and tighten using two 1/2-inch, box-end
lockwashers (4), and wrenches.
nuts (5)
8. Left side of engine Slave receptacle Screw on and tighten using 3/4-inch box-end
(6) cable (7), new wrench.
lockwasher (8), and
screw (9)
NOTE
FOLLOW-ON MAINTENANCE:
Change 1 2-895.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702131
Change 1 2-895.3
TM 5-3805-254-20-2
STARTER MOTOR
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2-896
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
2-897
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
Due to excessive weight, care must be taken to prevent personal injury or damage to equipment.
NOTE
INSTALLATION
Due to excessive weight, care must be taken to prevent personal injury or damage to equipment.
10 Starter motor (1) Screw (2) and new a With assistance, put starter motor in
lockwasher (3) lace.
b Screw in and tighten using 9/16-inch
half-moon wrench.
11. Two screws (4) and Screw in and tighten using 15/16-inch box-
two new lock- end wrench.
washers (5)
12. Nut (9), new lock- a Put ground wire and two ground straps in
washer (10), ground place.
wire (7), and two b Screw on and tighten using 3/4-inch
ground straps (11) box-end wrench.
2-898
TM 5-3805254-20-2
STARTER MOTOR - CONTINUED
NOTE
FOLLOW-ON MAINTENANCE:
TA244269
2-899
TM 5-380254-20-2
Page Page
INITIAL SETUP
2-900
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DRAINING
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
Hot transmission oil can burn you. Care must be taken to prevent personal injury.
NOTE
Transmission oil must be warm and engine shut down (TM 5-3805-254-10) before draining transmission.
TA244269
2-901
TM 5.3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
4 Transmission Two screws (6), two a Using 112-inch, 112-inch drive socket,
oil pan (5) lockwashers (7), shift 10-inch extension, and ratchet handle,
cable bracket (8), and unscrew and take out.
two spacers (9) Move shift cable bracket out of way.
b Get rid of lockwashers.
NOTE
Care must be taken not to tilt transmission oil pan to prevent oil from spilling.
2-902
TM 5-3805-254-20 2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-903
TM 5-3805254.20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
2-904
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244269
2-905
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
FILLING
19. Oil filler tube (1) Dipstick (2) Turn handle counterclockwise and pull out.
20. Oil filler tube (1) Add proper amount and grade of trans-
mission oil (LO 53805-254-12).
TA244269
2-906
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Materials/Parts
2-907
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Internal oil Screw (2) and flat Using 1/2-inch, 1/2-inch drive socket,
filter (1) washer (3) 3-inch extension, and ratchet handle,
unscrew and take out.
INSTALLATION
5. Internal oil Screw (2) and flat Screw in and torque to 10 to 13 ft lb (14 to 18
filter (1) washer (3) N.m) using 1/2-inch, 1/2-inch drive
socket, 3-inch extension, and 0 to 175 ft lb
(0 to 245 N.m) torque wrench.
TA244274
2-908
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Extension, 10-inch, 1/2-inch drive Lockwasher, shift cable bracket (two required)
Gloves, safety Lockwasher, side cover (four required)
Goggles, safety Lockwasher, U-bolt (two required)
Handle, ratchet, 1/2-inch drive Nut, self-locking, shift control
Pen, marking Rags, wiping (item 15, appendix C)
Pliers, roundnose, 8-inch Solvent, drycleaning (item 19, appendix C)
Socket, 1/2-inch, 1/2-inch drive
Wrench, box-end, 3/8-inch Personnel Required
Wrench, box-end, 7116-inch
Wrench, box-end, 1/2-inch One
Wrench, torque, 0 to 175 ft lb
(0 to 245 N.m) Equipment Condition
2-909
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 Shift control swivel Cotter pin (2) a Using 8-inch roundnose pliers,
lever (1) straighten ends and pull out.
b Get rid of.
3 Transmission oil Two screws (6), two a Using 112-inch, 1/2-inch drive socket,
pan (5) lockwashers (7), shift 10-inch extension, and ratchet handle,
cable bracket (8), and unscrew and take out.
two spacers (9) Move shift cable bracket out of way.
b Get rid of lockwashers.
4. Transmission shift Four screws (11), a. Using 7/16-inch box-end wrench, un-
control stand (10) four lockwashers screw and take out.
(12), and side b. Get rid of lockwashers.
cover (13) c. Take off side cover.
TA244275
2-910
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244276
2-911
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
9 Adapter plate (1) Two nuts (2), two a Using 318-inch box-end wrench, un-
lockwashers (3), two screw and take off.
flat washers (4), b Get rid of lockwashers.
U-bolt (5), spacer c Take off U-bolt and spacer.
(6), and shift d Take off shift control cable.
control cable (7) Do not let shift control cable fall
through hole in floor.
TA244277
2-912
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEAN ING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
11. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-913
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
16 Shift cable New self-locking Screw on and tighten using 112-inch box-
swivel (5) nut (6) end wrench.
17 Adapter plate (7) Shift control cable a Put shift control cable in position.
(8), spacer (9), b Put in spacer and U-bolt.
U-bolt (10), two c Screw on and tighten using 38-inch
flat washers (11), box-end wrench.
two new lockwashers Make sure shift control cable is not
(12), and two being forced to one side If shift
nuts (13) control cable is being forced to one
side, loosen two nuts, adjust, and
retighten.
19 Four screws (16) and Screw in and tighten using 7/16-inch box-
four new lock- end wrench.
washers (17)
2-914
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-913
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
16 Shift cable New self-locking Screw on and tighten using 112-inch box-
swivel (5) nut (6) end wrench.
17 Adapter plate (7) Shift control cable a Put shift control cable in position.
(8), spacer (9), b Put in spacer and U-bolt.
U-bolt (10), two c Screw on and tighten using 3/8-inch
flat washers (11), box-end wrench.
two new lockwashers Make sure shift control cable is not
(12), and two being forced to one side If shift
nuts (13) control cable is being forced to one
side, loosen two nuts, adjust, and
retighten.
19 Four screws (16) and Screw in and tighten using 7/16-inch box-
four new lock- end wrench.
washers (17)
2-914
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244278
2-915
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
26. Shift cable Flat washer (9) and a. Put on flat washer.
swivel (6) new cotter pin (10) b. Put in cotter pin and bend back ends
using 8-inch roundnose pliers.
NOTE
2-916
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts References
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Transmission shift Four screws (2) Using 7/16-inch, 1/2-inch drive socket, 6-
control stand (1) inch extension, and ratchet handle, un-
screw and take out.
2. Cab floor (3) Transmission shift a. Take off.
control stand (1) b. Get rid of grommet.
and grommet (4)
Change 1 2-917
TM 53805254202
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTIONIREPLACEMENT
NOTE
2-918
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
9. Transmission shift Four screws (4) Screw in and tighten using 7/16-inch, 112-
control stand (1) inch drive socket, 6-inch extension, and
ratchet handle.
NOTE
TA244281
2-919
TM 5-3805254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
Equipment condition leaves transmission shift cable disconnected and ready to be pulled out of truck.
Assistance will be needed to remove transmission shift cable from under truck.
DISASSEMBLY
3. Transmission shift Shift cable swivel a. Using 12-inch slip-joint pliers and 7/16-
cable (2) (4) and jamnut (5) inch open-end wrench, loosen.
b. Screw off shift cable swivel.
c. Screw off jamnut.
2-920
TM 5-3805254-20-2
ACTION
LOCATION ITEM REMARKS
5. Shift cable Two nuts (9), two a. Using 3/8-inch box-end wrench, un-
bracket (8) lockwashers (10), screw and take off.
two flat washers b. Get rid of lockwashers.
(11), U-bolt (12), c. Take off U-bolt and spacer.
and spacer (13) d. Get rid of transmission shift cable.
TA244282
2-921
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page
2-424).
INSPECTION/REPLACEMENT
NOTE
ASSEMBLY
2-922
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244283
2-923
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Assistance will be needed under truck to push and guide transmission shift cable up
through hole in cab floor.
ADJUSTMENT
NOTE
Transmission shift cable adjustments are performed with shift control lever and shift
control swivel lever in N (neutral) position. Perform steps 16 thru 19 only if transmission
shift cable is already connected to shift control swivel lever.
TA244284
2-924
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244285
2-925
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ADJUSTMENT - CONTINUED
21. Shift cable New cotter Put in and bend back ends using 8-inch
swivel (2) pin (4) roundnose pliers.
2-926
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
2-927
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
Hot transmission oil can burn you. Care must be taken to prevent personal injury.
1. Transmission oil Oil filler tube (2) a. Place 12-gallon container underneath.
pan (1) b. Using 1 1/16-inch open-end wrench,
slowly loosen and take off.
c. Allow oil to drain.
d. Get rid of drained oil (page 2-424).
2. Bracket (3) Screw (4), flat a. Using 7/16-inch box-end and 7/16-inch
washer (5), lock- open-end wrenches, unscrew and take
washer (6), nut (7), out.
and clamp (8) b. Get rid of lockwasher.
c. Take clamp off oil filler tube (2).
d. Take out oil filler tube (2).
3. Oil fillertube(9) Dipstick (10) Turn handle counterclockwise and pull out.
TA244287
2-928
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent PD680 is toxic and flammable. Wear protective safety goggles and gloves and
use only in a well ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe
vapors. Do not use near open flame or excessive heat. The flashpoint for type #1 drycleaning
solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning
solvent, get fresh air immediately, and get medical aid. If contact with eyes is made, flush your
eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
TA244288
2-929
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
9. Bracket (4) Clamp (3), screw a. Aline clamp and bracket holes.
(5), flat washer b. Screw on and tighten using 7/16-inch
(6), new lockwasher box-end and 7/16-inch open-end
(7), and nut (8) wrenches.
TA244289
2-930
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
10. Transmission oil Oil filler tube (1) Screw on and tighten using 1 1/16-inch
pan (9) open-end wrench.
NOTE
FOLLOW-ON MAINTENANCE:
2-931
TM 5-3805-254-20-2
AUXILIARY TRANSMISSION
INITIAL SETUP
Materials/Parts References
ACTION
LOCATION ITEM REMARKS
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
Do not check oil level when hot. Hot oil can burn you.
1. Auxiliary Filler plug (2) a. Wipe filler plug and area around it, clean
transmission (1) using wiping rag.
b. Using 15/16-inch open-end wrench,
unscrew and take out.
2-932
TM 5-3805-254-20-2
AUXILIARYTRANSMISSION - CONTINUED
ACTION
LOCATION ITEM REMARKS
DRAINING
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
Do not drain oil when hot. Hot oil can burn you.
NOTE
Auxiliary transmission oil must be warm and engine shut down (TM 5-3805-254-10).
TA244291
2-933
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
FILLING
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-934
TM 5-3805-254-20-2
INITIAL SETUP
2-935
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
Hot transmission oil can burn you. Care must be taken to prevent personal injury.
NOTE
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
Safety goggles must be worn when using wire brush. Flying rust and metal particles can cause
eye injury.
2-936
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
TA244293
2-937
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded
parts from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions
(page 2-424).
11. Oil filter Drainplug (6) a. Wrap pipe threads with antiseizing tape.
canister (1) b. Screw in and tighten using 7/16-inch
box-end wrench.
12. Dump truck Transmission a. Start engine and check transmission oil
level (TM 5-3805-254-10).
b. Check for leaks.
2-938
TM 5-3805-254-20-2
For propeller shaft and universal joint maintenance refer to Preventative Maintenance checks and Services (PMCS) page
2-34 and Lubrication Order (LO 5380525412). The intervals specified are based on operation under normal conditions.
Modification of the recommended intervals may be required under unusual operating conditions.
TA244294
2-939
TM 5-3805-254-20-2
Page Page
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for both rear axle housing breathers.
1. Rear axle Rear axle housing Using 3/4-inch open-end wrench, unscrew
housing (1) breather (2) and take out.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves
and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not
breathe vapors. Do not use near open flame or excessive heat. The flashpoint for type #1
drycleaning solvent is 1000F (380C) and for type #2 is 138°F (59°0C). If you become dizzy while
using cleaning solvent, get fresh air immediately, and get medical aid. If contact with eyes is
made, flush your eyes with water and get medical aid immediately.
Change 1 2-940
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed away
from user and other personnel in the area. Compressed air used for cleaning purposes shall not
exceed 30 psi (207 kPa). User must wear safety goggles or face shield to prevent personnel injury.
INSPECTION/REPLACEMENT
NOTE
INSTALLATION
CAUTION
Overtightening rear axle breather could cause damage to axle housing or breather.
4. Rear axle Rear axle housing Screw in and tighten using 3/4-inch open-
housing (1) breather (2) end wrench.
2-941
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
WARNING
Do not check rear axle housing oil level when hot. Hot oil can burn you.
NOTE
1. Rear axle Filler plug (2) Using wiping rag, wipe filler plug and area
housing (1) around it clean.
2-942
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
DRAINING
WARNING
Do not drain rear axle housing oil when hot. Hot oil can burn you.
NOTE
Rear axle housing oil must be warm and engine shut down (TM 5-3805-254-10) before draining.
6. Rear axle Filler plug (2) and a. Using wiping rag, wipe filler plug,
housing (1) magnetic drain magnetic drainplug, and area around it
plug (3) clean.
b. Place 10-gallon container underneath.
c. Using 1/2-inch square key, unscrew
and take out.
d. Allow oil to drain.
e. Get rid of drained oil (page 2-424).
TA244296
2-943
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
FILLING
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions
(page 2-424).
7. Rear axle Magnetic drain a. Using wiping rag, wipe magnetic drain
housing (1) plug (2) plug clean.
b. Using antiseizing tape wrap threads.
c. Screw in and tighten using 1/2-inch
square key.
TA244297
2-944
TM 5-3805-254-20-2
INTERAXLE DIFFERENTIAL
INITIAL SETUP
2-945
TM 5-3805-254-20-2
INTERAXLE DIFFERENTIAL - CONTINUED
ACTION
LOCATION ITEM REMARKS
DRAINING
WARNING
Do not drain interaxle differential oil when hot. Hot oil can burn you.
1 Interaxle Filler plug (2) a Using wiping rag, wipe filler plug and
differential (1) area around it clean.
b Using 5/8-inch open-end wrench, un-
screw and take out.
FILLING
2-946
TM 5-3805-254-20-2
INITIAL SETUP
Lower center instrument panel opened (page Tags, marking (item 21, appendix C)
2-438) Lockwasher, cab floor
Upper center instrument panel opened (page Lockwasher, front crossmember (two required)
2-439) Lockwasher, drop elbow
Change 1 2-946.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires. NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2 Elbow (4) Line nut (5) Using 9/16-inch open-end wrench, unscrew, and
take off.
3 Power divider control Elbow (4) Using 9/16-inch open-end wrench, unscrew, and
valve (1) take off.
4 Cab floor adapter (2) Line nut (6), tube a Using 9/16-inch open-end wrench, unscrew, and
(3), and elbow (7) take off.
b Take out tube.
7 Cab floor adapter (2) Elbow (8) Using 9/16-inch open-end wrench, unscrew, and
take off.
8 Cab floor (11) Nut (12), washer a Using 1-inch open-end wrench, unscrew, and
(13), cab floor take off.
adapter (2), and b Get rid of lockwasher.
lockwasher (14)
Change 1 2-946.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702132
Change 1 2-946.3
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
9 Adapter (1) Line nut (2) Using 9/16-inch open-end wrench, unscrew, and
take off.
10 Drop elbow (3) Adapter (1) Using 9/16-inch open-end wrench, unscrew, and
take off.
12 Adapter (6) Line nut (7) Using 9/16-inch open-end wrench, unscrew, and
take off.
13 Drop elbow (3) Adapter (6) Using 9/16-inch open-end wrench, unscrew, and
take off.
14 Frame (8) Screw (9), lockwasher a Using 7/16-inch box-end wrench, unscrew, and
(10), and washer (11) take off.
b. Get rid of lockwasher.
16 Two extension clips Two clamps (13), nuts a Using two 7/16-inch box-end
wrenches,
(12) (14), lockwashers unscrew, and take off.
(15), and screws (16) b Get rid of lockwashers.
18 Frame crossmember Two extension clips Using two 3/4-inch box-end wrenches, unscrew,
(18) (12), nuts (19), and take off.
screws (20)
20 Elbow (22) Line nut (23) Using 9/16-inch open-end wrench, unscrew, and
takeoff.
22 Power divider (4) Elbow (22) Using 9/16-inch open-end wrench, unscrew, and
take off.
Change 1 2-946.4
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
Replace all damaged or defective parts For more information on how to inspect parts,
go to General Maintenance Instructions (page 2-424).
23 Hose (5) and tube (17) Look for cracks, breaks, and wear.
24 All threaded parts Look for damaged threads or rounded heads.
25 All metal parts Look for cracks and breaks.
TA702133
Change 1 2-946.5
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
26 Power divider (1) Elbow (2) Screw on and tighten using 9/16-inch open-end
wrench.
30 Frame crossmember (7) Two extension clips Screw on and tighten using two 3/4-inch box-end
(8), nuts (9), and wrenches.
screws (10)
32 Two extension clips Two clamps (11), nuts Screw on and tighten using two 7/16-inch box-end
(8) (12), new lockwashers wrenches.
(13), and screws (14)
35 Drop elbow (16) Adapter (20) Screw on and tighten using 9/16-inch open-end
wrench.
36 Adapter (20) Line nut (21) a Screw on and tighten using 9/16-inch open-
end wrench.
b Get rid of tags.
37 Drop elbow (16) Adapter (22) Screw on and tighten using 9/16-inch open-end
wrench.
38 Adapter (22) Line nut (23) Screw on and tighten using 9/16-inch open-
end wrench.
Change 1 2-946.6
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702134
Change 1 2-946.7
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
39 Cab floor (1) Nut (2), washer (3), Screw on and tighten using 1-inch open-end
wrench.
cab floor adapter
(4), and new
lockwasher (5)
40 Cab floor adapter (4) Elbow (6) Screw on and tighten using 9/16-inch open-end
wrench.
41 Elbow (6) Line nut (7) and Screw on and tighten using 9/16-inch open-end
tube (8) wrench.
42 Cab floor adapter (4) Line nut (9), tube a Put tube in place.
(10), and elbow (11) b Screw on and tighten using 9/16-inch open-end
wrench.
43 Power divider control Elbow (13) Screw on and tighten using 9/16-inch open-end
valve (12) wrench.
44 Elbow (13) Line nut (14) a Screw on and tighten using 9/16-inch open-end
wrench.
b Get rid of tags.
NOTE
FOLLOW-ON MAINTENANCE:
Change 1 2-946.8
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
Page Page
Airbrake Cylinder Control Valve .................... 2-1034.1 Front Brakes .................................................. 2-947
Airbrake System Draining.............................. 2-1034 Front Brake Limiting and Quick
Air Compressor Governor to Air Release Valve ................................................ 2-1084.1
Dryer Lines and Fittings............................ 2-1040 Front Brake Limiting and Quick
Air Compressor Governor to Wet Release Valve to Brake Teadle
Air Reservoir Lines and Valve Hose..................................................... 2-1084
Fittings ........................................................... 2-1046 Front Brake Limiting Control Valve
Air Compressor to Air Dryer Hoses and Fittings ......................................... 2-1159
Hose and Lines......................................... 2-1035 Front Rear Quick Release Valve ................... 2-1088.1
Air Dryer ........................................................ 2-1002 Front Rear Quick Release Valve to
Air Dryer Cartridge......................................... 2-1014 Parking Airbrake Chamber
Alcohol Evaporator ........................................ 2-995 Hoses ............................................................. 2-1088.3
Brake Pedal ................................................... 2-1021 Front Rear T-Fitting........................................ 2-1093.0
Brake Treadle Valve to Double Front Rear T-Fitting to Service
Check Valve T-Fitting Hose...................... 2-1062 Airbrake Chamber Hoses............................... 2-1093.1
Brake Treadle Valve and Right Front Relay Valve........................................... 2-1098.1
Manifold Hoses......................................... 2-1052 Front Relay Valve T-Fitting to
Brake Treadle Valve to T-Mani- Rear Relay Valve Hose.................................. 2-1105
fold Hoses................................................. 2-1067 Front Relay Valve to Front Rear
Cab Floor Through Connector to T-Fitting Hose................................................. 2-1099
Double Check Valve Hose........................ 2-1108 Front Relay Valve to Rear Relay
Chassis 90-Degree Elbow............................. 2-1151.0 Valve Hose..................................................... 2-1101
Chassis T-Fitting ........................................... 2-1151.2 Left Front Wheel to Front Brake
Chassis T-Fitting to Chassis Limiting and Quick Release Valve
90-Degree Elbow Hose ............................ 2-1151.3 Hoses ............................................................. 2-1115
Chassis T-Fitting to Double Parking Brake Control Valve .......................... 2-1024.1
Check Valve Hose .................................... 2-1143 Parking Brake Lines ....................................... 2-1025
Chassis T-Fitting to Front Rear Rear Brakes ................................................... 2-955
Quick Release Valve Hose....................... 2-1146 Rear Rear Quick Release Valve .................... 2-1130.1
Chassis 90-Degree Elbow to Rear Rear Rear Quick Release Valve to
Rear Quick Release Valve Parking Airbrake Chamber
Hose ......................................................... 2-1157 Hoses ............................................................. 2-1131
Double Check Valve...................................... 2-1148.1 Rear Rear Quick Release Valve to
Double Check Valve T-Fitting to Service Airbrake Chamber
Front Relay Valve T-Fitting Hoses ............................................................. 2-1136
Hose ......................................................... 2-1149 Rear Relay Valve ........................................... 2-1140.1
Double Check Valve to Double Check Rear Relay Valve to Rear Rear
Valve T-Fitting Hose ................................. 2-1071 Quick Release Valve Hose ............................ 2-1140.3
Dry Air Reservoir ........................................... 2-975 Right Front Wheel to Front Brake
Dry Air Reservoir to Front Relay Limiting and Quick Release Valve
Valve Hose ............................................... 2-1080 Hoses ............................................................. 2-1122
Dry Air Reservoir to T-Manifold T-Manifold ...................................................... 2-1077.0
Hoses ....................................................... 2-1074 Wet Air Reservoir ........................................... 2-986
Dry Air Reservoir to Wet Air Wet Air Reservoir to Air Dryer
Reservoir Hoses ....................................... 2-1077.2 Hose............................................................... 2-1154
Change 1 2-947
TM 5-3805-254-20-2
FRONT BRAKES
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Parts of the service brake assembly will be coated with asbestos dust. Breathing this dust may be hazardous
to your health. Use a filter mask approved for use against asbestos dust. Never use compressed air or dry
brush to clean these assemblies. Dust shall be removed using an industrial-type vacuum cleaner with a high-
efficiency filter system.
NOTE
Steps given are typical for right side and left side front brakes.
1 Dust shield (1) Two brakeshoes (2) Using industrial type vacuum, clean
and brake spider (3) asbestos dust and dirt.
Change 1 2-948
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Brake springs under tension can injure or kill Use extreme care to prevent injury Safety goggles must be worn.
2 Two brakeshoes (2) Two brake Using brake repair pliers, take off.
springs (4)
TA244299
2-949
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only
in a well-ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use
near open flame or excessive heat The flashpoint for type #1 drycleaning solvent is 1000F (380C) and for
type #2 is 138°F (590C) If you become dizzy while using cleaning solvent, get fresh air immediately, and get
medical aid If contact with eyes is made, flush your eyes with water and get medical aid immediately.
Parts of the service brake assembly will be coated with asbestos dust Breathing this dust may be
hazardous to your health Use a filter mask approved for use against asbestos dust Never use compressed
air or dry brush to clean these assemblies Dust shall be removed using an industrial-type vacuum cleaner
with a high-efficiency filter system.
NOTE
INSPECTION/REPLACEMENT
NOTE
2-950
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244300
2-951
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for right and left front brakes.
8 Brake spider (1) Four brakeshoe Coat with thin layer of grease.
rest pads (2) Wipe off excess.
Make sure hands are free of grease when handling brakeshoes to prevent grease from getting on linings.
NOTE
Position brakeshoes on brake spider with DRUM ROTATION stamping facing out and arrows facing forward
direction of wheels.
10 Brake spider (1) Upper brakeshoe (4) Position behind upper holddown clip (5) and
into slots of both adjusting screw rings (3).
Brake springs under tension can injure or kill Use extreme care to prevent injury Safety goggles must be worn.
NOTE
Hold upper and lower brakeshoes together when performing next step.
2-952
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
12 Upper brakeshoe (4) Two brake a Hook into holes in upper brakeshoe.
and lower brake- springs (8) b Connect to holes in lower brakeshoe
shoe (6) using brake repair pliers.
TA244301
2-953
TM 5-3805-254-20-2
FRONT BRAKES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
ADJUSTMENT
NOTE
Steps given are typical for adjusting upper and lower brakeshoes on right and left front wheels.
14 Dust shield (2) Cover (3) Pry out using 3/8-inch flat-tip screwdriver.
NOTE
2-954
TM 5-3805-254-20-2
REAR BRAKES
INITIAL SETUP
Materials/Parts - Continued
Tools
Locknut, airbrake chamber (two required)
Brush, cleaning Locknut, brake spider (eight required)
Brush, wire Lockwasher, brake spider (eight required)
Gage, depth, tire tread Lockwasher, camshaft bracket (four required)
Gloves, safety Packing, anchor pin (four required)
Goggles, safety Packing, brake camshaft
Hammer, ball-peen, 2-pound Rags, wiping (item 15, appendix C)
Hammer, plastic-face Ring, slack adjuster (one required)
Handle, ratchet, 1/2-inch drive Ring, anchor pin (four required)
Mask, filter Screw, dust shield (six required)
Pliers, brake repair Solvent, drycleaning (item 19, appendix C)
Pliers, retaining ring
Pliers, roundnose, 8-inch Personnel Required
Press, anchor pin
Screwdriver, flat-tip, 1/8-inch Two
Socket, 3/4-inch, 112-inch drive
Socket, 15/16-inch, 1/2-inch drive Equipment Condition
Vacuum, industrial-type
Wrench, box-end, 9/16-inch Rear hub and brakedrum assembly removed
Wrench, box-end, 15116-inch (page 2-1188).
Wrench, open-end, 15/16-inch
References
Materials/Parts
TM 5-3805-254-10 (Operator’s Manual)
Compound, antiseizing (item 4,
appendix C)
Cotter pin, clevis
Grease, GAA (item 10, appendix C)
2-955
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Parts of the service brake assembly will be coated with asbestos dust Breathing this dust may be
hazardous to your health Use a filter mask approved for use against asbestos dust Never use compressed air
or dry brush to clean these assemblies Dust shall be removed using an industrial-type vacuum cleaner with a
high-efficiency filter system.
NOTE
Steps given are typical for right and left front rear and rear rear brakes.
2 Slack adjuster (2) Adjusting screw Using 9/16-inch box-end wrench, push in
(3) and locking on locking sleeve and turn until brake cam-
sleeve (4) shaft S-head (5) is horizontal and slack
adjuster is loose.
2-956
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5 Upper anchor Two rings (9), two a Using 1/8-inch flat-tip screwdriver, pry
pin (8) packing retainers off rings.
(10), and two b Take off packing retainers and packings.
packings (11) c Get rid of rings and packings.
6 Brake spider (12) Upper anchor pin (8) Using anchor pin press, press out.
WARNING
Brake springs under tension can injure or kill Use extreme care to prevent injury Safety goggles must be
worn.
TA244303
2-957
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
9 Lower dust Three screws (2) a Using 9/16-inch box-end wrench, un-
shield (1) screw and take out.
b Get rid of.
11 Lower anchor Two rings (4), two a Using 1/8-inch flat-tip screwdriver, pry
pin (3) packing retainers off rings.
(5), and two b Take off packing retainers and packings.
packings (6) c Get rid of rings and packings.
12 Brake spider (7) Lower anchor pin (3) a Using anchor pin press, press out
and lower brake- anchor pin.
shoe (8) b Take off lower brakeshoe.
TA244304
2-958
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
If slack adjuster is being replaced, perform steps 14, 15, and 16.
14 Clevis (11) Cotter pin (12) and a Using 8-inch roundnose pliers, take out
yoke pin (13) cotter pin.
b Get rid of cotter pin.
c Take out yoke pin.
15 Slack adjuster (14) Ring (15) and two a Using retaining ring pliers, take off ring.
flat washers (16) b Get rid of ring.
c Take off flat washers.
16 Brake camshaft (17) Slack adjuster (14) Using 2-pound ball-peen hammer, tap
gently and pull off.
TA244305
2-959
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
20 Airbrake chamber (7) Two locknuts (8) a Using 15/16-inch box-end wrench, un-
and two flat screw and take off.
washers (9) b Get rid of locknuts.
CAUTION
Do not allow airbrake chamber to hang by airbrake hoses Damage to airbrake hoses could result.
24 Brake spider (13) Six screws (14), six a Using 15/16-inch, 1/2-inch drive
lockwashers (15),and socket, ratchet handle, and 15/16-inch
six locknuts (16) box-end wrench, unscrew and take off.
b Get rid of lockwashers and locknuts.
2-960
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only in
a well-ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use near
open flame or excessive heat The flashpoint for type #1 drycleaning solvent is 100°F (380C) and for type #2 is
138°F (590C) If you become dizzy while using cleaning solvent, get fresh air immediately, TA244306 and get
medical aid If contact with eyes is made, flush your eyes with water and get 2-961 medical aid immediately.
TA244306
2-961
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Parts of the service brake assembly will be coated with asbestos dust Breathing this dust may be hazardous to your health
Use a filter mask approved for use against asbestos dust Never use compressed air or dry brush to clean these
assemblies Dust shall be removed using an industrial-type vacuum cleaner with a high-efficiency filter system.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Safety goggles must be worn when using wire brush Flying rust and metal particles can cause eye injury.
29 Upper and lower a Clean off rust and scale using wire
anchor pins (5) and brush.
brake rollers (6) b Wipe clean using drycleaning solvent
and wiping rag.
2-962
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
Replace all damaged or defective parts.
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Steps given are typical for both brakeshoes and their components.
TA244307
2-963
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT- CONTINUED
TA244308
2-964
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
TA244309
2-965
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
39. Rear axle Brake spider (2) Put in place and aline holes.
housing (1)
40. Brake spider (2) Two screws (3), two Put in holes from front of brake spider.
new lockwashers Do not tighten.
(4), and two new
locknuts (5)
41. Six screws (6), six Put in remaining six holes from rear of brake
new lockwashers spider.
(7), and six new Do not tighten.
locknuts (8)
42. Two screws (3) and Tighten on alternate sides using 15/16-
six screws (6) inch, 1/2-inch drive socket, ratchet
handle, and 15/16-inch box-end wrench.
43. Brake spider (2) Camshaft bracket (9) Put in place and aline holes.
TA24431 0
2-966
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
44. Four screws (10) Screw in and tighten using 3/4-inch, 112-
and four new inch drive socket and ratchet handle.
lockwashers (11)
45. Camshaft bracket (9) Airbrake Aline two studs (13) with holes and push into
chamber (12) place.
46. Two studs (13) Two flat washers Screw on and tighten using 15116-inch box-
(14) and two new end wrench.
locknuts (15)
TA244311
2-967
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
49. Brake camshaft (1) Two flat washers (2) Put on.
NOTE
50. Brake camshaft (1) Slack adjuster (3) a. Coat splines with antiseizing compound.
b. Put on.
Position lower hole as close as
possible to clevis (4).
52. New ring (6) Put into groove using retaining ring pliers.
Make sure entire ring is in groove.
53. Slack adjuster (3) Clevis (4), new a. Aline lower hole in slack adjuster with
cotter pin (7), and clevis.
yoke pin (8) b. Put in yoke pin.
c. Put cotter pin through yoke pin and bend
ends enough to prevent falling out.
TA244312
2-968
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
54. Brake spider (9) Lower anchor a. Coat lower anchor pin and brake spider
pin (10) and lower bore with antiseizing compound.
brakeshoe (11) b. Place lower brakeshoe in position.
c. Push lower anchor pin into place.
If necessary, tap in using plastic-
face hammer.
TA244313
2-969
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
57. Brake spider (1) Upper anchor pin (2) a. Coat upper anchor pin and brake spider
and upper brake- bore with antiseizing compound.
shoe (3) b. Place upper brakeshoe in position.
c. Push upper anchor pin into place.
If necessary, tap in using plastic-
face hammer.
58. Upper anchor pin (2) Two new packings (4) Put on.
and two packing
retainers (5)
59. Two new rings (6) Put in groove using retaining ring pliers.
Make sure rings are In grooves.
60. Upper brakeshoe (3) Brake roller (7) and a. Coat brake roller and brake camshaft S-
clip (8) head (9) with a thin layer of GAA
grease.
b. Put brake roller in position.
c. Position clip around brake roller and
connect to upper brakeshoe.
TA244314
2-970
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
61. Lower brakeshoe (10) Brake roller (11) a. Coat brake roller with a thin layer of
GAA and clip (12)grease.
b. Hold brake roller in place.
c. Position clip around brake roller and
connect to lower brakeshoe.
62. Upper brakeshoe (3) Brake spring (13) Hook onto upper brakeshoe and connect to
and lower brake- lower brakeshoe using brake repair pliers.
shoe (10)
TA244315
2-971
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
63. Brake spider (1) Lower dust Put in place and aline.
shield (2)
64. Lower dust Three new screws (3) Screw in and tighten using 9116-inch box-
shield (2) end wrench.
65. Brake spider (1) Upper dust Put in place and aline.
shield (4)
66. Upper dust Three new screws (5) Screw in and tighten using 9/16-inch box-
shield (4) end wrench.
TA244316
2-972
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ADJUSTMENT
NOTE
Steps given are typical for right and left front rear and rear rear brakes.
68. Slack adjuster (7) Adjusting screw (8) While slowly turning rear hub, push in
and locking locking sleeve and adjust until a heavy drag
sleeve (9) is felt, then back off to allow a slight drag
using 9116-inch box-end wrench.
69. Airbrake Push rod (11) and a. Start engine to build up air pressure
chamber (10) slack adjuster (7) (TM 5-3805254-10).
b. Have assistant hold down brake pedal.
c. Check for 90-degree angle between
push rod and slack adjuster.
See illustration.
If angle Is correct, shut down
engine(TM 5-3805254-10) and task
ends here.
If angle Is less than 90-degrees,
have assistant release brake pedal
and perform steps 70 thru 74.
TA244317
2-973
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ADJUSTMENT - CONTINUED
70. Push rod (1) Nut (2) and Using 15/16-inch open-end wrench,
clevis (3) loosen and move nut away from clevis.
71. Clevis (3) Cotter pin (4) and a. Using 8-inch roundnose pliers, take out
yoke pin (5) cotter pin.
b. Take out yoke pin.
72. Push rod (1) Clevis (3) Turn to adjust to position needed.
73. Clevis (3) Nut (2) Turn toward clevis and tighten using 15116-
inch open-end wrench.
74. Slack adjuster (6) Clevis (3), cotter a. Aline lower hole in slack adjuster with
pin (4), and yoke clevis.
pin (5) b. Put in yoke pin.
c. Put cotter pin through yoke pin.
d. Bend back ends of cotter pin using 8-
inch roundnose pliers.
e. Perform step 69 again.
NOTE
TA244318
2-974
TM 5-3805-254-20-2
INITIAL SETUP:
Tools Materials/Parts
Change 1 2-975
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Drain air from airbrake system before removing lines or fittings to avoid injury to personnel from
compressed air.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
7. Two cable Two nuts (14), two a. Using 9/16-inch, 1/2-inch drive deep
assemblies (13) lockwashers (15), and socket, 6-inch extension, and ratchet
two flat washers (16) handle, unscrew and take off.
b. Get rid of lockwashers.
8. Bracket (17) Two cable Pull out and move out of way.
assemblies (13)
2-976
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Due to excessive weight and size, assistance will be needed when handling dry air reservoir. Failure to
observe this precaution could cause injury to personnel.
CAUTION
Care must be taken not to drop dry air reservoir. Damage to fittings or draincocks could occur.
9. Bracket (17) Dry air With assistance, lift up and pull out.
reservoir (1)
TA244319
2-977
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
10. Dry air 90-degree elbow (2) Using 13/16-inch open-end wrench, un-
reservoir (1) screw and take out.
13. Check valve (5) 90-degree elbow (6) Using 1 318-inch and 13/16-inch open-end
wrenches, unscrew and take out.
14. 45-degree elbow (7) Check valve (5) Using 1 318-inch open-end wrench, un-
screw and take out.
15. Dry air 45-degree elbow (7) Using 1-inch open-end wrench, unscrew
reservoir (1) and take out.
16. Check valve (8) 90-degree elbow (9) Using 1 318-inch and 13/16-inch open-end
wrenches, unscrew and take out.
17. 45-degree elbow (10) Check valve (8) Using 1 3/8-inch open-end wrench, un-
screw and take out.
18. Dry air 45-degree elbow (10) Using 1-inch open-end wrench, unscrew
reservoir (1) and take out.
19. Four step Four locknuts (12) a. Using 9/16-inch box-end wrench, un-
studs (11) and four flat screw and take out.
washers (13) b. Get rid of locknuts.
NOTE
2-978
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
21. 90-degree elbow (15) Draincock (16) Using 9/16-inch open-end wrench, un-
screw and take out.
22. Dry air 90-degree elbow (15) Using 11/16-inch open-end wrench, un-
reservoir (1) screw and take out.
TA244320
2-979
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
Safety goggles must be worn when using wire brush. Flying rust and metal particles can cause eye injury.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
2-980
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244321
2-981
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
29. Dry air 45-degree elbow (2) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 1-inch open-
end wrench.
30. 45-degree elbow (2) Check valve (3) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 318-inch
open-end wrench.
31. Check valve (3) 90-degree elbow (4) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 3/8-inch
and 13/16-inch open-end wrenches.
32. Dry air 45-degree elbow (5) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 1-inch open-
end wrench.
33. 45-degree elbow (5) Check valve (6) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 3/8-inch
open-end wrench.
34. Check valve (6) 90-degree elbow (7) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 3/8-inch
and 13/16-inch open-end wrenches.
35. Dry air 90-degree elbow (8) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 7/8-inch
open-end wrench.
36. 45-degree elbow (9) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 3/4-inch
open-end wrench.
37. 90-degree elbow (10) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 13/16-inch
open-end wrench.
2-982
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
38. 90-degree elbow (11) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 11/16-inch
open-end wrench.
Position facing rear of dry air
reservoir.
39. 90-degree elbow (11) Draincock (12) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 9/16-inch
open-end wrench.
c. Turn to close.
40. Dry air Five plugs (13) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 38-inch,
1/2-inch drive square socket and
ratchet handle.
42. Four new locknuts Screw on and tighten using 9/16-inch box-
(16) and four flat end wrench.
washers (17)
TA244322
2-983
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
WARNING
Due to excessive weight and size, assistance will be needed when handling dry air reservoir. Failure to
observe this precaution could cause injury to personnel.
CAUTION
Care must be taken not to drop dry air reservoir. Damage to fittings or draincocks could occur.
44. Two cable Put over dry air reservoir (2) and through
assemblies (3) bracket.
45. Two cable Two nuts (4), two Screw on and tighten using 9/16-inch, 112-
assemblies (3) new lockwashers (5), inch drive deep socket, 6inch extension,
and two flat and ratchet handle.
washers (6)
46. Dry air 90-degree elbow (7) Wrap pipe threads with antiseizing tape.
reservoir (2)
47. 90-degree elbow (7) Airhose to wet air a. Screw on and tighten using 7/8-inch
reservoir rear (8)open-end wrench.
b. Take off tag.
c. Get rid of tag.
48. Dry air 90-degree elbow (9) Wrap pipe threads with antiseizing tape.
reservoir (2)
49. 90-degree elbow (9) Airhose to wet air a. Screw on and tighten using 7/8-inch
reservoir front (10) open-end wrench.
b. Take off tag.
c. Get rid of tag.
50. Dry air 90-degree elbow (11) Wrap pipe threads with antiseizing tape.
reservoir (2)
51. 90-degree elbow (11) Airhose to relay a. Screw on and tighten using 1 1/4-inch
valve (12) open-end wrench.
b. Take off tag.
c. Get rid of tag.
2-984
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
52. Dry air 45-degree elbow (13) Wrap pipe threads with antiseizing tape.
reservoir (2)
53. 45-degree elbow (13) Airhose to tee (14) a. Screw on and tighten using 1-inch open-
end wrench.
b. Take off tag.
c. Get rid of tag.
54. Dry air 90-degree elbow (15) Wrap pipe threads with antiseizing tape.
reservoir (2)
55. 90-degree elbow (15) Airhose to tee (16) a. Screw on and tighten using 1-inch open-
end wrench.
b. Takeoff tag.
c. Get rid of tag.
TA244323
2-985
TM 5-3805-254-20-2
INITIAL SETUP:
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Drain air from airbrake system before removing lines or fittings to avoid injury to personnel from
compressed air.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-986
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5. Fitting (10) Air line to compres- Using 11/16-inch and 9/16-inch open-end
sor governor (11) wrenches, unscrew and take off.
6. Two clamps (12) Two screws (13) and a. Using two 9/16-inch box-end wrenches,
two locknuts (14) unscrew and take off.
b. Get rid of locknuts.
CAUTION
Care must be taken not to drop wet air reservoir. Damage to fittings or automatic drain valve could occur.
TA244324
2-987
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
8. Wet air 90-degree elbow (2) Using 13/16-inch open-end wrench, un-
reservoir (1) and 45-degree elbows screw and take out.
(3 and 4)
10. Fitting (7) Fitting (5) Using 7/8-inch and 11/16-inch open-end
wrenches, unscrew and take out.
11. Wet air Fitting (7) Using 7/8-inch open-end wrench, unscrew
reservoir (1) and take out.
12. Fitting (8) Automatic drain Using 1 1/8-inch and 11/16-inch open-end
valve (9) wrenches, unscrew and take out.
13. Tee fitting (10) Fitting (8) Using 314-inch and 11/16-inch open-end
wrenches, unscrew and take out.
15. Fitting (12) T-fitting (10) Using two 3/4-inch open-end wrenches,
unscrew and take off.
16. Wet air Fitting (12) Using 3/4-inch open-end wrench, unscrew
reservoir (1) and take out.
17. Fitting (13) Pressure relief Using 7/8-inch and 5/8-inch open-end
valve (14) wrenches, unscrew and take out.
18. Wet air Fitting (13) Using 7/8-inch open-end wrench, unscrew
reservoir (1) and take out.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
2-988
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Safety goggles must be worn when using wire brush. Flying rust and metal particles can cause eye injury.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
TA244325
2-989
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
TA244326
2-990
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
25. Wet air 90-degree elbow (10) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 13116-inch
open-end wrench.
26. 45-degree elbow (11) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 13116-inch
open-end wrench.
27. 45-degree elbow (12) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 13/16-inch
open-end wrench.
TA244327
2-991
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
28. Wet air Fitting (2) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 7/8-inch
open-end wrench.
29. Fitting (2) Fitting (3) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 7/8-inch and
11/16-inch open-end wrenches.
30. Fitting (3) Fitting (4) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 11/16-inch
and 9/16-inch open-end wrenches.
31. Wet air Fitting (5) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 3/4-inch
open-end wrench.
32. Fitting (5) T-fitting (6) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 3/4-inch
open-end wrench.
Put in vertical position.
33. T-fitting (6) Plug (7) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 3/8-inch
open-end wrench.
35. Fitting (8) Automatic drain Screw on and tighten using 1 1/8-inch
valve (9) open-end wrench.
36. Wet air Fitting (10) a. Wrap pipe threads with antiseizing tape.
reservoir (1) b. Screw in and tighten using 7/8-inch
open-end wrench.
2-992
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
37. Fitting (10) Pressure relief a. Wrap pipe threads with antiseizing tape.
valve (11) b. Screw in and tighten using 7/8-inch and
5/8-inch open-end wrenches.
TA244328
2-993
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Care must be taken not to drop wet air reservoir. Damage to fittings or automatic drain valve could occur.
Antiseizing tape must be used on all pipe threads to provide a good seal and prevent threaded parts from
seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
39. Two screws (3) and Screw in and tighten using two 9/16-inch
two new locknuts (4) box-end wrenches.
40. Wet air 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
reservoir (2)
41. 90-degree elbow (5) Airhose to air a. Screw on and tighten using 1-inch open-
dryer (6)end wrench.
b. Take off tag.
c. Get rid of tag.
42. Wet air 45-degree elbow (7) Wrap pipe threads with antiseizing tape.
reservoir (2)
43. 45-degree elbow (7) Airhose to dry air a. Screw on and tighten using 7/8-inch
reservoir rear (8)open-end wrench.
b. Take off tag.
c. Get rid of tag.
44. Wet air 45-degree elbow (9) Wrap pipe threads with antiseizing tape.
reservoir (2)
45. 45-degree elbow (9) Airhose to dry air a. Screw on and tighten using 718-inch
reservoir front (10)open-end wrench.
b. Take off tag.
c. Get rid of tag.
46. Wet air Fitting (11) Wrap pipe threads with antiseizing tape.
reservoir (2)
2-994
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
47. Fitting (11) Air line to Screw on and tighten using 11/16-inch and
compressor 9/16-inch open-end wrenches.
governor (12)
ALCOHOL EVAPORATOR
INITIAL SETUP:
Tools Materials/Parts
TA244329
Change 1 2-995
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not smoke or allow open flames or sparks into areas where alcohol is being used. Failure to observe
this precaution could cause death or serious injury to personnel.
Care must be taken when taking off canister to prevent spilling alcohol. Injury to personnel could result.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
4. Bracket (7) Three screws (8), a. Using 7/16-inch open-end and 716-
three lockwashers inch box-end wrenches, unscrew and
(9), and three take off.
nuts (10) b. Get rid of lockwashers.
5.1. Two screws (10.1), a. Using 1/2-inch open-end and 1/2-inch box-
two lockwashers (10.2), end wrenches, unscrew, and take off.
and two nuts (10.3) b. Get rid of lockwashers.
DISASSEMBLY
6. Housing (1) 90-degree elbow (3) Using 1/2-inch open-end wrench, unscrew
and take out.
7. Fitting (11) 90-degree elbow (5) Using 5/8-inch and 1/2-inch open-end
wrenches, unscrew and take out.
Change 1 2-996
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
10. Air tube (13) and a. Using 7/16-inch open-end wrench, un-
rubber washer (14) screw and take out.
b. Get rid of rubber washer.
TA702136
Change 1 2-997
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
12. Cannister (2) Wipe inside and outside clean using dry-
cleaning solvent and wiping rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-
424).
2-998
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244331
2-999
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
17. Housing (1) Fitting (2) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 5/8-inch
open-end wrench.
18. Fitting (2) 90-degree elbow (3) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 5/8-inch and
1/2-inch open-end wrenches.
19. Housing (1) 90-degree elbow (4) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1/2-inch
open-end wrench.
20. Air tube (5) and new Screw in and tighten using 7116-inch open-
rubber washer (6) end wrench.
Do not overtighten.
TA244332
2-1000
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
21.2. Two screws (7.3), Screw on and tighten using 1/2-inch box-end
two new lockwashers and 1/2-inch open-end wrenches.
(7.4), and two nuts (7.5)
23. Three screws (9), Screw on and tighten using 7116-inch box-
three new lock- end and 7/16-inch open-end wrenches.
washers (10), and
three nuts (11)
24. Housing (1) 90-degree elbow (3) Wrap pipe threads with antiseizing tape.
25. 90-degree elbow (3) Airhose (12) Screw on and tighten using 9/16-inch open-
end wrench.
26. Housing (1) 90-degree elbow (4) Wrap pipe threads with antiseizing tape.
27. 90-degree elbow (4) Vacuum hose (13) Screw on and tighten using 9/16-inch open-
end wrench.
TA702137
Change 1 2-1001
TM 5-3805-254-20-2
AIR DRYER
INITIAL SETUP:
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Drain air from airbrake system before removing lines or fittings to avoid injury to personnel from
compressed air.
Change 1 2-1002
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
6. Heater wire (12) Nut (13) Using 3/8-inch open-end wrench, unscrew
and take off.
TA244334
2-1003
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
WARNING
Assistance will be needed to support air dryer when performing steps 8 thru 10 to prevent injury to
personnel.
8. Right bracket (1) Two screws (2) Using 3/4-inch,1/2-inch drive socket,
and two nuts (3) 3-inch extension, ratchet handle, and
3/4-inch box-end wrench, unscrew and
take out.
9. Left bracket (4) Two screws (5) Using 3/4-inch, 1/2-inch drive socket,
and two nuts (6) 3-inch extension, ratchet handle, and
3/4-inch box-end wrench, unscrew and
take out.
10. Frame rail (7) Air dryer (8) With assistance, take off.
DISASSEMBLY
11. Top clamp (9) Two screws (10), two a. Using two 9/16-inch box-end wrenches,
flat washers (11), two unscrew and take out.
lockwashers (12), b. Get rid of lockwashers.
and two nuts (13)
TA244335
2-1004
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13. Air dryer (8) Top clamp (9) Open and slide off.
14. Bottom clamp (17) Two screws (18), a. Using two 9116-inch box-end wrenches,
two flat washers unscrew and take off.
(19), two lock- b. Get rid of lockwashers.
washers (20), and
two nuts (21)
17. Air dryer (8) Bottom clamp (17) Open and slide off.
TA244336
2-1005
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY - CONTINUED
18. Air dryer (1) Two plugs (2) Using 7/8-inch box-end wrench, unscrew
and take out.
20. Check valve (4) 90-degree elbow (5) Using 1 1/4-inch and 13/16-inch open-end
wrenches, unscrew and take out.
21. Air dryer (1) Check valve (4) Using 1 1/4-inch open-end wrench, un-
screw and take out.
22. 90-degree elbow (6) Pressure relief Using 3/4-inch open-end wrench, unscrew
valve (7) and take out.
23. Air dryer (1) 90-degree elbow (6) Using 13/16-inch open-end wrench, un-
screw and take out.
24. Head assembly (8) 45-degree elbow (9) Using 5/8-inch open-end wrench, unscrew
and take out.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
Safety goggles must be worn when using wire brush. Flying rust or metal particles could cause eye injury.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-1006
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
25. Air dryer (1) a. Clean rust, scale, and corrosion from
outside surfaces using wire brush.
b. Wipe clean using drycleaning solvent
and wiping rag.
c. To touch-up or repaint, refer to
TM 43-0139.
26. Two brackets (10) a. Clean rust, scale, and corrosion using
and two clamps (11)wire brush.
b. Wipe clean using drycleaning solvent
and wiping rag.
c. To touchup or repaint, refer to
TM 43-0139.
TA244337
2-1007
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page
2-424).
TA244338
2-1008
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
32. Head assembly (7) 45-degree elbow (10) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 5/8-inch
open-end wrench.
33. Air dryer (1) 90-degree elbow (11) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 13116-inch
open-end wrench.
34. 90-degree elbow (11) Pressure relief a. Wrap pipe threads with antiseizing tape.
valve (12) b. Screw in and tighten using 3/4-inch
open-end wrench.
35. Airdryer (1) Two plugs (13) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 7/8-inch
box-end wrench.
TA244339
2-1009
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
36. Air dryer (1) Check valve (2) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 1/4-inch
open-end wrench.
37. Check valve (2) 90-degree elbow (3) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1 1/4-inch
and 13/16-inch open-end wrenches.
38. Air dryer (1) 90-degree elbow (4) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 3/4-inch
open-end wrench.
40. Bottom clamp (5) Cap screw (6), new Put in place.
lockwasher (7), and Do not tighten.
nut (8)
TA244340
2-1010
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
43. Bottom clamp (5) Right bracket (13) Put into position.
and top clamp (9) and left bracket (14)
44. Bottom clamp (5) Two screws (15), two Screw in and tighten using two 9/16-inch
flat washers (16), box-end wrenches.
two new lockwashers
(17), and two
nuts (18)
45. Top clamp (9) Two screws (19), two Screw in and tighten using two 9/16-inch
flat washers (20), box-end wrenches.
two new lockwashers
(21), and two
nuts (22)
TA244341
2-1011
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
WARNING
Assistance will be needed to support air dryer while performing steps 46, 47, and 48. Failure to observe
this precaution could cause injury to personnel.
46. Frame rail (1) Air dryer (2), right Put in place alining holes in right and left
bracket (3), and brackets with holes in frame rail.
left bracket (4)
47. Right bracket (3) Two screws (5) and Screw in and tighten using 3/4-inch, 112-
two nuts (6) inch drive socket, 3-inch extension, ratchet
handle, and 3/4-inch box-end wrench.
48. Left bracket (4) Two screws (7) and Screw in and tighten using 3/4-inch, 1/2-
two nuts (8) inch drive socket, 3-inch extension, ratchet
handle, and 3/4-inch box-end wrench.
49. Air dryer (2) Pressure relief Turn air dryer to position pressure relief
valve (9) valve toward front of dump truck.
NOTE
50. Clamp (10) Pinch screw (11) Tighten using two 1/2-inch box-end
and nut (12) wrenches.
51. Air dryer (2) 90-degree elbow (13) Wrap pipe threads with antiseizing tape.
TA244342
2-1012
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
52. 90-degree elbow (13) Outlet airhose (14) a. Screw on and tighten using 1-inch open-
end wrench.
b. Take off tag.
c. Get rid of tag.
53. Air dryer (2) 90-degree elbow (15) Wrap pipe threads with antiseizing tape.
54. 90-degree elbow (15) Inlet air line (16) a. Screw on and tighten using 15/16-inch
open-end wrench.
b. Takeoff tag.
c. Get rid of tag.
55. Head assembly (17) 45-degree elbow (18) Wrap pipe threads with antiseizing tape.
56. 45-degree elbow (18) Governor line (19) a. Screw on and tighten using 5/8-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
TA244343
2-1013
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
3. Terminal (5) Nut (6) and heater Using 3/8-inch open-end wrench, unscrew
wire (7) and take off.
2-1014
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Head assembly (3) Three screws (8), a. Using 7/16-inch box-end wrench, un-
three lockwashers screw and take off.
(9), and three b. Get rid of lockwashers.
clips (10)
CAUTION
Care must be taken not to strike heater wire terminal or 45-degree elbow.
5. Air dryer (11) Head assembly (3) Using plastic-face hammer, strike gently to
push up.
TA244344
2-1015
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
CAUTION
Position cartridge with cartridge locknut facing up to prevent beads from spilling.
10. Cartridge (1) Cartridge locknut a. Using 3/4-inch 1/2-inch drive deep
(2) and cartridge socket, ratchet handle, and 11/16-inch
screw (3) box-end wrench, unscrew and take off
cartridge locknut.
b. Get rid of cartridge locknut.
Do not take out cartridge screw.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
2-1016
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
16. Air dryer (12) Wipe inside clean using drycleaning solvent
and wiping rag.
18. Head assembly (13) Clean using drycleaning solvent and wiping
rag.
19. Washer (5) and Clean using drycleaning solvent and wiping
spring (6) rag.
TA244345
2-1017
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-
424).
20. Air dryer (1) a. Look for bent or broken retaining ring
flange (2).
b. Look inside for excessive rust, scale, or
corrosion.
If excessive rust or corrosion is found,
replace air dryer (page 2-1002).
TA244346
2-1018
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Position new cartridge with cartridge locknut facing up to prevent beads from spilling.
25. Plate (3) New ball check a. Drop in ball check valve.
valve (8) and b. Put retaining clip in position.
clip (9)
26. Screw (10) and new Screw in and tighten using number two
lockwasher (11) cross-tip screwdriver.
NOTE
Hold cartridge screw from being pushed out when performing next step.
30. Cartridge screw (15) New cartridge Screw on and tighten using 3/4-inch 112-
locknut (16) inch drive deep socket, ratchet handle, and
11/16-inch box-end wrench.
TA244347
2-1019
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
31. Air dryer (1) New cartridge (2) Screw in and tighten using 314-inch 1/2-
inch drive deep socket and ratchet handle.
32. Head assembly (3) New ring (4) a. Coat with lubricating oil.
b. Put on up to lip (5).
NOTE
NOTE
35. Head assembly (3) Three clips (7) Put into position.
36. Three screws (8) Screw in and tighten using 7/16-inch box-
and three new end wrench.
lockwashers (9)
NOTE
For more information on antiseizing tape, go to General Maintenance Instructions (page 2-424).
37. 45-degree elbow (10) Wrap pipe threads with antiseizing tape.
38. 45-degree elbow (10) Governor line (11) a. Screw on and tighten using 518-inch
open-end wrench.
b. Get rid of tag.
2-1020
TM 5-3805-254-20-2
NOTE
BRAKE PEDAL
INITIAL SETUP:
Tools Materials/Parts
One
TA244348
2-1021
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Brake pin (1) Cotter pin (2) a. Using 6-inch long-nose pliers, bend
back ends and pull out.
b. Get rid of.
2. Brake pedal (3) Brake pin (1) Using 6-inch long-nose pliers, pull out.
DISASSEMBLY
4. Roller pin (4) Cotter pin (5) a. Using 6-inch long-nose pliers, bend
back ends and pull out.
b. Get rid of.
5. Brake pedal (3) Roller pin (4) Using 6-inch long-nose pliers, pull out.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
Safety goggles must be worn when using wire brush. Flying rust or metal particles could cause eye injury.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-1022
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page
2-424).
10. Brake pedal (3) a. Look for cracks or breaks near brake pin
bosses (7) and roller pin bosses (8).
b. Look for worn or distorted brake pin (1)
and roller pin (4) holes.
11. Brake pin (1) and Look for cracks, breaks, bends, or
roller pin (4) grooves.
TA244349
2-1023
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
13. Brake pedal (1) Roller (2) a. Coat with thin layer of GAA grease.
b. Put in.
14. Roller pin (3) a. Coat with thin layer of GAA grease.
b. Put in.
15. Roller pin (3) New cotter pin (4) Put in and bend back ends using 6-inch
long-nose pliers.
INSTALLATION
17. Brake pedal (1) Brake pin (6) a. Coat with thin layer of GAA grease.
b. Put in.
18. Brake pin (6) New cotter pin (7) Put in and bend back ends using 6-inch
long-nose pliers.
TA244350
2-1024
TM 5-3805-254-20-2
INITIAL SETUP:
Lower center instrument panel removed (page Lockwasher, control valve (two required)
2-424).
Parking brake lines and fittings removed (page Personnel Required
2-1025).
One
Tools/Test Equipment
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA702138
Change 1 2-1024.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
3. Instrument panel (1) Two screws (2) and a. Using number one cross-tip screwdriver,
lockwashers (3) unscrew, and take off.
b. Get rid of lockwashers.
4. Parking brake Take off.
control valve (4)
INSTALLATION
6. Two screws (2) and Screw in and tighten using number one cross-tip
new lockwashers (3) screwdriver.
7. Parking brake Nut (5) Using 7/16-inch open-end wrench, screw on.
control valve (4) Do not tighten.
NOTE
FOLLOW-ON MAINTENANCE:
1. Install parking brake lines and fittings (page 2-1025).
2. Install lower center instrument panel (page 2-424).
TA702139
Change 1 2-1024.2
TM 5-3805-254-20-2
INITIAL SETUP:
2-1025
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Care must be taken when working behind instrument panel to prevent damaging wires or components.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
5. T-fitting (10) Line nut (11) Using 9/16-inch open-end wrench, un-
screw and take off.
6. Power divider Line nut (13), air line a. Using 9/16-inch open-end wrench, un-
control valve (8) (9), and 90-degree screw and take off.
elbow (12) b. Take out air line.
Change 1 2-1026
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8. Parking brake Line nut (16), Using 518-inch and 9/16-Inch open-end
control valve (1) T-fitting (10), wrenches, unscrew and take off.
and 45-degree
elbow (17)
TA702140
Change 1 2-1027
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
9. Driver’s side Screw (2) and a. Using 3/8-inch box-end wrench, un-
firewall (1) clamp (3) screw and take out.
b. Take off clamp.
10. Driver’s seat Line nut (5) and Using 9/16-inch open-end wrench, un-
valve assembly (4) air line (6) screw and take off.
11. Left side cab Fourteen screws a. Using number two cross-tip screw-
floor (7) (8) and left scuff driver, unscrew and take out.
plate (9) b. Take off left scuff plate.
12. Left side rear Eight screws (11), a. Using number two cross-tip screw-
cab wall (10) eight flat washers driver, unscrew and take out.
(12), and left lower b. Push air line (6) through hole while tak-
rear molding (13) ing off left lower rear molding.
Be careful not to bend or crimp air
line.
13. Cab floor through- Line nut (15) and a. Using 5/8-inch open-end wrench, un-
connector 90-degree air line (16) screw and take off.
elbow (14) b. Take out air line.
TA244352
2-1028
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page
2-424).
TA244353
2-1029
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
16. Cab rear Cab floor through Wrap pipe threads with antiseizing tape.
floor (1) connector 90-degree
elbow (2)
17. Cab floor through Line nut (3) and a. Screw on and tighten using 5/8-inch
connector 90-degree air line (4) open-end wrench.
elbow (2) b. Route air line as shown.
18. Left side rear Air line (6) and a. Push air line through hole.
cab wall (5) left lower rear b. Put left lower rear molding in position.
molding (7)
19. Left lower rear Eight screws (8) Screw in and tighten using number two
molding (7) and eight flat cross-tip screwdriver.
washers (9)
20. Left side Left scuff plate a. Put left scuff plate in position.
cab floor (10) (11) and fourteen b. Screw in and tighten using number two
screws (12)cross-tip screwdriver.
2-1030
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
22. Driver’s side Air line (4), clamp a. Put clamp around air line.
firewall (13) (14), and screw (15) b. Screw in and tighten using 318-inch
box-end wrench.
23. Driver’s seat valve Air line (17) Screw on and tighten using 9/16-inch
assembly (16) open-end wrench.
CAUTION
Care must be taken when working behind instrument panel to prevent damaging wires or components.
TA244355
2-1031
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
NOTE
24. Parking brake 45-degree elbow (1.1) Wrap pipe threads with antiseizing tape.
control valve (1) and T-fitting (2)
26. Air line (4) Screw on and tighten using 9/16-inch open-
end wrench.
27. Power divider 90-degree elbow (6) Wrap pipe threads with antiseizing tape.
control valve (5)
29. Parking brake 45-degree elbow (7) Wrap pipe threads with antiseizing tape.
control valve (1)
31. Double check Fitting (10) Wrap pipe threads with antiseizing tape.
valve (9)
Change 1 2-1032
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
TA702141
Change 1 2-1033
TM 5-3805-254-20-2
INITIAL SETUP:
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
WARNING
Drain air from airbrake system before removing hoses, lines or fittings to avoid injury to personnel from
compressed air.
1. Dry air Two draincocks (2) a. Turn counterclockwise to open and allow
reservoir (1) compressed air to drain.
b. Turn clockwise to close.
TA244357
2-1034
TM 5-3805-254-20-2
INITIAL SETUP:
Front brake limiting control valve hoses and fit- Wrench, box-end, 7/16-inch
tings disconnected (page 2-1159). Wrench, open-end, 1-inch
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA702142
Change 1 2-1034.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
6. Airbrake cylinder Nut (3) Screw on and tighten using 1 -inch open-end
control valve (2) wrench.
NOTE
FOLLOW-ON MAINTENANCE: Connect front brake limiting control valve hoses and fittings
(page 2-1159).
TA702143
Change 1 2-1034.2
TM 5-3805-254-20-2
INITIAL SETUP:
Materials/Parts One
2-1035
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
Air line is in three sections. Tag sections from front to rear of truck as section 1, section 2, and section 3.
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2. Air line (2) Line nut (3) Using 1-inch open-end wrench, unscrew
and take off.
3. Three clamps (4) Screw (5), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (6), and open-end wrenches, unscrew and take
nut (7) out.
b. Get rid of lockwasher.
c. Take clamps off air line (2).
4. Air line (2) and Line nut (9) and a. Using 1-inch and 15/16-inch open-end
airhose (8) line nut (10) wrenches, unscrew and take off.
b. Take out air line (2).
6. Airhose (8) and Line nut (12) and a. Using 1-inch and 15116-inch open-end
air line (11) line nut (13) wrenches, unscrew and take off.
b. Take out airhose (8).
NOTE
8. Air line (11) Screw (14), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (15), nut open-end wrenches, unscrew and take
(16), clamp (17), out.
and clamp (18) b. Get rid of lockwasher.
c. Take clamp (17) off air line.
9. Air dryer (19) and Line nut (21) and a. Using 15/16-inch open-end wrench,
90-degree elbow (20) air line (11) unscrew and take off.
b. Take out air line.
2-1036
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
10. Airhose (8) Clean using liquid detergent and wiping rag.
11. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page
2-424).
12. Air lines (2 and 11) a. Look for cracks, breaks, kinks, or
and airhose (8) chafing.
b. Look for excessive rust or corrosion.
TA244358
2-1037
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
14. Air dryer (1) 90-degree elbow (2) Wrap pipe threads with antiseizing tape.
15. 90-degree elbow (2) Air line (3) a. Screw on and tighten using 15/16-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
NOTE
16. Clamp bracket (4) Clamp (5), clamp a. Put clamp (5) around air line and
and air line (3) (6), screw (7), new position with clamp (6) on clamp
lockwasher (8), and bracket.
nut (9) b. Screw in and tighten using 7/16inch
box-end and 7/16-inch open-end
wrenches.
18. Air line (3) and Line nut (11) and a. Screw on and tighten using 1-inch and
airhose (10) line nut (12) 15/16-inch open-end wrenches.
b. Take tag off air hose.
c. Get rid of tag.
19. Airhose (10) and Line nut (14) and a. Screw on and tighten using 1-inch and
air line (13) line nut (15) 15/16-inch open-end wrenches.
b. Take tag off air line.
c. Get rid of tag.
2-1038
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
20. Air line (13) Clamp (16) Put on and aline with holes in two clamps.
21. Clamp (16) and Screw (18), new Screw in and tighten using 7/16-inch box-
two clamps (17) lockwasher (19), and end and 7/16-inch open-end wrenches.
nut (20)
22. Air compressor (21) 90-degree elbow (22) Wrap pipe threads with antiseizing tape.
23. 90-degree elbow (22) Air line (13) Screw on and tighten using 1-inch open-
end wrench.
NOTE
TA244359
2-1039
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
Air line is in three sections. Tag sections from front to rear of truck as section 1, section 2, and section 3.
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2. Air line (2) Line nut (3) Using 5/8-inch open-end wrench, unscrew
and take off.
2-1040
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
3. Three clamps (4) Screw (5), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (6), and open-end wrenches, unscrew and take
nut (7) out.
b. Get rid of lockwasher.
c. Take clamp off air line (2).
4. Adapter (8) Line nut (9) a. Using 5/8-inch and 9116-inch open-
end wrenches, unscrew and take off.
b. Take out air line (2).
6. Line nut (11) Connector (10) Using 9/16-inch and 7/16-inch open-end
wrenches, unscrew and take off.
TA244360
2-1041
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
8. Air line (1) Line nut (2) and a. Using 9/16-inch and 7/16-inch open-
connector (3) end wrenches, unscrew and take off.
b. Take out air line.
10. Line nut (5) Adapter (4) Using 5/8-inch and 9/16-inch open-end
wrenches, unscrew and take off.
12. Air line (6) Screw (7), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (8), nut (9), open-end wrenches, unscrew and take
and clamp (10) out.
b. Get rid of lockwasher.
c. Take off clamp.
13. 45-degree elbow (11) Line nut (12) a. Using 5/8-inch open-end wrench, un-
screw and take off.
b. Take out air line (6).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
14. All metal parts Clean using drycleaning solvent and wiping
rag.
2-1042
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-
424).
TA244361
2-1043
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
17. Air dryer (1) 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
18. 45-degree elbow (2) Air line (3) a. Screw on and tighten using 518-inch
and line nut (4) open-end wrench.
b. Take off tag.
c. Get rid of tag.
19. Clamp bracket (5) Clamp (6), clamp a. Put clamp (6) around air line and posi-
and air line (3) (7), screw (8), new tion with clamp (7) on clamp bracket.
lockwasher (9), and b. Screw in and tighten using 7/16-inch
nut (10) box-end and 7/16-inch open-end
wrenches.
21. Adapter (11) Line nut (12) Screw on and tighten using 5/8-inch and
9/16-inch open-end wrenches.
24. Connector (13) Air line (14) and a. Screw on and tighten using 5/8-inch and
line nut (15) 9/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
26. Air line (14) Connector (16) and Screw on and tighten using 9/16-inch and
line nut (17) 7/16-inch open-end wrenches.
27. Connector (16) Adapter (18) Screw on and tighten using 9/16-inch and
7/16-inch open-end wrenches.
2-1044
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
29. Air line (19) Adapter (18) and a. Screw on and tighten using 5/8-lnch and
line nut (20) 9/16-inch open-end wrenches.
b. Take tag off air line.
c. Get rid of tag.
30. Clamp (21) Put on and aline holes in two clamps (22).
31. Clamps (21 and 22) Screw (23), new Screw in and tighten using 7/16-inch box-
lockwasher (24), end and 7116-inch open-end wrenches.
and nut (25)
32. Air compressor 90-degree elbow (27) Wrap pipe threads with antiseizing tape.
governor (26)
33. 90-degree elbow (27) Line nut (28) Screw on and tighten using 5/8-inch open-
end wrench.
NOTE
TA244362
2-1045
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
Air line is in three sections. Tag sections from front to rear of truck as section 1, section 2, and
section 3.
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2. Air line (2) Line nut (3) and Using 5/8-inch open-end wrench, unscrew
adapter (3.1) and take off.
Change 1 2-1046
TM 5-3805-254-20-2
AIR COMPRESSOR GOVERNOR TO WET AIR RESERVOIR LINES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
3. Three clamps (4) Screw (5), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (6), and open-end wrenches, unscrew and take
nut (7) out.
b. Get rid of lockwasher.
c. Take clamp off air line (2).
4. Adapter (8) Line nut (9) a. Using 5/8-inch and 9/16-inch open-
end wrenches, unscrew and take off.
b. Take out air line (2).
6. Line nut (11) Connector (10) Using 9/16-inch and 7/16-inch open-end
wrenches, unscrew and take off.
TA702144
Change 1 2-1047
TM 5-3805-254-20-2
AIR COMPRESSOR GOVERNOR TO WET AIR RESERVOIR LINES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
8. Air line (1) Line nut (2) and a. Using 9/16-inch and 7/16-inch open-
connector (3) end wrenches, unscrew and take off.
b. Take out air line.
10. Line nut (5) Adapter (4) Using 11/16-inch and 9/16-inch open-end
wrenches, unscrew and take off.
12. Wet air reservoir Line nut (9) and a. Using 11/16-inch and 9/16-inch open-
(7) fitting (8) end wrenches, unscrew and take off.
b. Take out air line (6).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
13. All metal parts Clean using drycleaning solvent and wiping
rag.
Change 1 2-1048
TM 5-3805-254-20-2
AIR COMPRESSOR GOVERNOR TO WET AIR RESERVOIR LINES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-
424).
TA244364
2-1049
TM 5-3805-254-20-2
AIR COMPRESSOR GOVERNOR TO WET AIR RESERVOIR LINES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
16. Wet air Fitting (2) Wrap pipe threads with antiseizing tape.
reservoir (1)
19. Adapter (5) Line nut (6) Screw on and tighten using 11/16-inch and
9/16-inch open-end wrenches.
21. Adapter (5) Connector (7) Screw on and tighten using 9/16-inch and
7/16-inch open-end wrenches.
22. Connector (7) Air line (8) and a. Screw on and tighten using 5/8-inch and
line nut (9) 9/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
24. Air line (8) Connector (10) and Screw on and tighten using 9/16-inch and
line nut (11) 7/16-inch open-end wrenches.
Change 1 2-1050
TM 5-3805-254-20-2
AIR COMPRESSOR GOVERNOR TO WET AIR RESERVOIR LINES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
25. Connector (10) Adapter (12) Screw on and tighten using 9/16-inch and
7/16-inch open-end wrenches.
27. Air line (13) Adapter (12) and a. Screw on and tighten using 5/8-inch and
line nut (14) 9/16-inch open-end wrenches.
b. Take tag off air line.
c. Get rid of tag.
28. Clamp (15) Put on and aline holes in two clamps (16).
29. Clamps (15 and 16) Screw (17), new Screw on and tighten using 7/16-inch box-
lockwasher (18), end and 7/16-inch open-end wrenches.
and nut (19)
30. Air compressor Adapter (21) Wrap pipe threads with antiseizing tape.
governor (20)
31. Adapter (21) and Screw on and tighten using 5/8-inch open-
line nut (22) end wrench.
NOTE
TA244365
Change 1 2-1051
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2-1052
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Two clamp Two screws (11), a. Using 7/16-inch box-end and 7116-inch
brackets (10) two lockwashers open-end wrenches, unscrew and take
(12), and two out.
nuts (13) b. Get rid of two lockwashers.
TA244366
2-1053
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
11. Top of cab floor (1) Brake pedal Remove (page 2-1021).
12. Brake treadle valve Six screws (3) and a. Using 1/2-inch, 1/2-inch drive socket,
mounting plate (2) six lockwashers (4) 3-inch extension, and ratchet handle,
unscrew and take out.
b. Get rid of six lockwashers.
13. Top of cab floor (1) Brake treadle valve Take out.
mounting plate (2)
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
2-1054
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244367
2-1055
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
34. Four airhoses Clean using liquid detergent and wiping rag.
35. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1056
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
38. Engine side of Four airhoses (2) Push through hole until visible from under
firewall (1) cab floor (3).
NOTE
TA244368
2-1057
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
40. Brake treadle 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
valve (1)
41. 45-degree elbow (2) Airhose tagged a. Screw on and tighten using 7/8-inch
no. 4 (3) open-end wrench.
b. Take off tag.
c. Get rid of tag.
42. Brake treadle 45-degree elbow (4) Wrap pipe threads with antiseizing tape.
valve (1)
43. 45-degree elbow (4) Airhose tagged a. Screw on and tighten using 3/4-inch
no. 1 (5) open-end wrench.
b. Take off tag.
c. Get rid of tag.
44. Brake treadle 90-degree elbow (6) Wrap pipe threads with antiseizing tape.
valve (1)
45. 90-degree elbow (6) Airhose tagged a. Screw on and tighten using 7/8-inch
no. 3 (7) open-end wrench.
b. Take off tag.
c. Get rid of tag.
48. Brake treadle Fitting (8) Wrap pipe threads with antiseizing tape.
valve (1)
47. Fitting (8) Airhose tagged a. Screw on and tighten using 3/4-inch and
no. 2 (9) 11/16-inch open-end wrenches.
b. Takeoff tag.
c. Get rid of tag.
48. Brake treadle 45-degree elbow (10) Wrap pipe threads with antiseizing tape.
valve (1)
49. 45-degree elbow (10) Airhose (11) a. Screw on and tighten using 7/8-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
50. Brake treadle 45-degree elbow (12) Wrap pipe threads with antiseizing tape.
valve (1)
2-1058
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
51. 45-degree elbow (12) Airhose (13) a. Screw on and tighten using 7/8-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
52. Brake treadle Fitting (14) Wrap pipe threads with antiseizing tape.
valve (1)
53. Fitting (14) Airhose (15) a. Screw on and tighten using 1-inch and
7/8-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
54. Brake treadle 90-degree elbow (16) Wrap pipe threads with antiseizing tape.
valve (1)
55. 90degree elbow (16) Airhose (17) a. Screw on and tighten using 1-inch open-
end wrench.
b. Take off tag.
c. Get rid of tag.
TA244369
2-1059
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
WARNING
Safety gogles must be worn when working under truck to prevent eye injury.
57. Under cab floor (1) Brake treadle Have assistant push into hole and hold in
valve (2) position.
58. Top of cab Brake treadle valve Put in position and aline with holes on brake
floor (3) mounting plate (4) treadle valve (2).
59. Brake treadle valve Three screws (5) Screw in until snug, by hand.
mounting plate (4) and three new
lockwashers (6)
63. Engine side of Four airhoses (10) Put clamps around airhoses as shown.
firewall (9) and four clamps (11)
64. Two clamp Four clamps (11) Put in position and aline holes in clamps with
brackets (12) holes in clamp brackets.
65. Two screws (13), Screw in and tighten using 7/16-inch box-
two new lockwashers end and 7/16-inch open-end wrenches.
(14), and two
nuts (15)
66. Right manifold (16) 45-degree elbow (17) Wrap pipe threads with antiseizing tape.
67. 45-degree elbow (17) Airhose tagged a. Screw on and tighten using 3/4-inch
no. 1 (18) open-end wrench.
b. Take off and get rid of tag.
68. Right manifold (16) 45-degree elbow (19) Wrap pipe threads with antiseizing tape.
69. 45-degree elbow (19) Airhose tagged a. Screw on and tighten using 3/4-inch
no. 2 (20) open-end wrench.
b. Take off and get rid of tag.
2-1060
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
70. Right manifold (16) 45-degree elbow (21) Wrap pipe threads with antiseizing tape.
71. 45-degree elbow (21) Airhose tagged a. Screw on and tighten using 7/8-inch
no. 3 (22) open-end wrench.
b. Take off tag.
c. Get rid of tag.
72. Right manifold (16) 45-degree elbow (23) Wrap pipe threads with antiseizing tape.
73. 45-degree elbow (23) Airhose tagged a. Screw on and tighten using 7/8-inch
no. 4 (24) open-end wrench.
b. Take off tag.
c. Get rid of tag.
FOLLOW-ON MAINTENANCE:
TA244370
2-1061
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
2-1062
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
9. Left frame rail (13) Clamp (14), screw a. Using 7/16-inch box-end and 7/16-inch
and airhose (11) (15), lockwasher open-end wrenches, unscrew and take
(16), and nut (17) out.
b. Get rid of lockwasher.
c. Take clamp off airhose.
10. Double check valve Line nut (19) a. Using 7/8-inch and 13/16-inch open-
T-fitting (18) end wrenches, unscrew and take off.
b. Take out airhose (11).
TA244371
2-1063
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
12. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1064
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
15. Left frame rail (1) Double check valve Wrap pipe threads with antiseizing tape.
T-fitting (2)
16. Double check valve Airhose (3) Screw on and tighten using 718-inch and
T-fitting (2) 13/16-inch open-end wrenches.
NOTE
18. Clamp bracket (5) Clamp (4), screw a. Aline holes in clamp and clamp bracket.
(6), new lock- b. Screw in and tighten using 7/16-inch
washer (7), and box-end and 7/16-inch open-end
nut (8) wrenches.
TA244372
2-1065
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
20. Brake treadle 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
valve (1)
21. 45-degree elbow (2) Airhose (3) a. Screw on and tighten using 7/8-inch
open-end wrench.
b. Takeoff tag.
c. Get rid of tag.
22. Brake treadle 45-degree elbow (4) Wrap pipe threads with antiseizing tape.
valve (1)
23. 45-degree elbow (4) Airhose (5) a. Screw on and tighten using 7/8-inch
open-end wrench.
b. Takeoff tag.
c. Get rid of tag.
24. Brake treadle Fitting (6) Wrap pipe threads with antiseizing tape.
valve (1)
25. Fitting (6) Airhose (7) a. Screw on and tighten using 1-inch and
7/8-inch open-end wrenches.
b. Takeoff tag.
c. Get rid of tag.
26. Brake treadle 90-degree elbow (8) Wrap pipe threads with antiseizing tape.
valve (1)
27. 90-degree elbow (8) Airhose (9) a. Screw on and tighten using 1-inch open-
end wrench.
b. Takeoff tag.
c. Get rid of tag.
2-1066
TM 5-3805-254-20-2
BRAKE TREADLE VALVE TO DOUBLE CHECK VALVE T-FITTING HOSE - CONTINUED TM 5-3805-254-20-2
INITIAL SETUP:
TA244373
2-1067
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
5. T-manifold (6.1) Line nut (8) and Using 1-inch open-end wrench, unscrew
45-degree elbow (7) and take off.
7. Undercab floor (11) Screw (12), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (13), nut open-end wrenches, unscrew and take
(14), and clamp (15) out.
b. Take clamp off airhoses (2 and 5).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
Change 1 2-1068
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more Information on how to clean parts, go to General Maintenance Instructions (page 2-424).
10. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA702145
Change 1 2-1069
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
13. T-manifold (1) 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
14. 45-degree elbow (2) Screw on and tighten using 1-inch open-
and airhose (3) end wrench.
15. T-manifold (1) 45-degree elbow (4) Wrap pipe threads with antiseizing tape.
16. 45-degree elbow (4) Screw on and tighten using 1-inch open-
and airhose (5) end wrench.
17. Brake treadle Fitting (7) Wrap pipe threads with antiseizing tape.
valve (6)
18. Fitting (7) Airhose (3) a. Screw on and tighten using 1-inch and
7/8-inch open-end wrenches.
b. Takeoff tag.
c. Get rid of tag.
19. Brake treadle 90-degree elbow (8) Wrap pipe threads with antiseizing tape.
valve (6)
20. 90-degree elbow (8) Airhose (5) a. Screw on and tighten using 1-inch open-
end wrench.
b. Take off tag.
c. Get rid of tag.
21. Under cab floor (9) Clamp (10), screw a. Put clamp around air hoses (3 and 5)
(11), new lockwasher and put in position.
(12), and nut (13) b. Screw in and tighten using 7/16-inch
box-end and 7/16-inch open-end
wrenches.
Change 1 2-1070
TM 5-3805-254-20-2
INITIAL SETUP:
TA244375
2-1071
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Double check valve (7) Line nut (2) and Using 3/4-inch open-end wrench, unscrew
45-degree elbow (1) and take off.
2. Fitting (3) Line nut (4) and a. Using 3/4-inch and 5/8-inch open-end
airhose (5) wrenches, unscrew and take off.
b. Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
Change 1 2-1072
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Double check Fitting (3) Wrap pipe threads with antiseizing tape.
valve tee (6)
7. Fitting (3) Airhose (5) Screw on and tighten using 3/4-inch and
5/8-inch open-end wrenches.
8. Double check 45-degree elbow (1) Wrap pipe threads with antiseizing tape.
valve (7)
TA244376
TASK ENDS HERE
Change 1 2-1073
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. 90-degree elbow (1) Line nut (2) Using 1-inch open-end wrench, unscrew
and take off.
2. 45-degree elbow (3) Line nut (4) Using 1-inch open-end wrench, unscrew
and take off.
3. T-manifold (4.1) Line nut (6), airhose (7), a. Using 1-inch open-end wrench, un-
and 90-degree elbow (5) screw and take off.
b. Take out airhose.
4. Line nut (9), airhose (10), a. Using 1-inch open-end wrench, un-
and 90-degree elbow (8) screw and take off.
b. Take out airhose.
Change 1 2-1074
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
5. Airhoses (7 and 10) Clean using liquid detergent and wiping rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA702146
Change 1 2-1075
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
8. T-manifold (1) 90-degree elbow (2) Wrap pipe threads with antiseizing tape.
10. T-manifold (1) 90-degree elbow (4) Wrap pipe threads with antiseizing tape.
12. Dry air 45-degree elbow (7) Wrap pipe threads with antiseizing tape.
reservoir (6)
13. 45-degree elbow (7) Airhose (5) Screw on and tighten using 1-inch open-end
wrench.
14. Dry air 90-degree elbow (8) Wrap pipe threads with antiseizing tape.
reservoir (6)
15. 90-degree elbow (8) Airhose (3) Screw on and tighten using 1-inch open-end
wrench.
Change 1 2-1076
TM 5-3805-254-20-2
TA244378
Change 1 2-1077
TM 5-3805-254-20-2
T-MANIFOLD
INITIAL SETUP:
Dry air reservoir to T-manifold hoses disconnected Lockwasher, T-manifold (four required)
(page 2-1074).
Brake treadle valve to T-manifold hoses discon- Personnel Required
nected (page 2-1067).
One
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. T-manifold (1) Two nuts (2), a. Using7/16-inch open-end wrench and 7/16-inch
lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b. Get rid of lockwashers.
3. Cab floor (6) Two nuts (7), a. Using 7/16-inch open-end wrench and 7/16-inch
lockwashers (8), box-end wrench, unscrew, and take off.
and screws (9) b. Get rid of lockwashers.
INSTALLATION
6. Two nuts (7), new Screw in and tighten using 7/16-inch box-end
lockwashers (8), wrench and 7/16-inch open-end wrench.
and screws (9)
Change 1 2-1077.0
TM 5-3805-254-20-2
T-MANIFOLD - CONTINUED
ACTION
LOCATION ITEM REMARKS
8. T-manifold (1) Two nuts (2), new Screw in and tighten using 7/16-inch box-end wrench
lockwashers (3), and 7/16-inch open-end wrench.
and screws (4)
NOTE
FOLLOW-ON MAINTENANCE:
TA702147
Change 1 2-1077.1
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. 90-degree elbow (1) Line nut (2) Using 7/8-inch open-end wrench, unscrew
and take off.
2. 90degree elbow (3) Line nut (4) Using 7/8-inch open-end wrench, unscrew
and take off.
3. 45-degree elbow (5) Line nut (6) and a. Using 7/8-inch open-end wrench, un-
airhose (7) screw and take off.
b. Take out airhose.
4. 45-degree elbow (8) Line nut (9) and a. Using 718-inch open-end wrench, un-
airhose (10) screw and take off.
b. Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
5. Airhoses (7 and 10) Clean using liquid detergent and wiping rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1078
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
8. Wet air 45-degree elbow (8) Wrap pipe threads with antiseizing tape.
reservoir (11)
9. 45-degree elbow (8) Airhose (10) Screw on and tighten using 7/8-inch open-
end wrench.
10. Wet air 45-degree elbow (5) Wrap pipe threads with antiseizing tape.
reservoir (11)
11. 45-degree elbow (5) Airhose (7) Screw on and tighten using 7/8-inch open-
TA244380
2-1079
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
12. Dry air 90-degree elbow (2) Wrap pipe threads with antiseizing tape.
reservoir (1)
13. 90-degree elbow (2) Airhose (3) Screw on and tighten using 7/8-inch open-
end wrench.
14. Dry air 90-degree elbow (4) Wrap pipe threads with antiseizing tape.
reservoir (1)
15. 90-degree elbow (4) Airhose (5) Screw on and tighten using 7/8-inch open-
end wrench.
TA244379
2-1080
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
2-1081
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
NOTE
2. Left frame rail (1) Clamp (3), screw a. Using 7/16-inch box-end and 7/16-inch
and airhose (2) (4), lockwasher (5), open-end wrenches, unscrew and take
and nut (6) out.
b. Get rid of lockwasher.
c. Take clamp off airhose.
3. Front relay valve Line nut (8), airhose (2), a. Using 1 1/4-inch and 1 1/16-inch open-
(9) and fitting (7) end wrenches, unscrew and take off.
b. Take out airhose.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1082
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
8. Front relay Fitting (7) Wrap pipe threads with antiseizing tape.
valve (9)
NOTE
TA244381
Change 1 2-1083
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
11. Clamp bracket (1) Clamp (2), screw a. Aline holes in clamp and clamp bracket.
(3), new lockwasher b. Screw in and tighten using 7/16-inch
(4), and nut (5) box-end and 7/16-inch open-end
wrenches.
12. Dry air 90-degree elbow (7) Wrap pipe threads with antiseizing tape.
reservoir (6)
13. 90-degree elbow (7) Airhose (8) Screw on and tighten using 1 1/4-inch
open-end wrench.
TA703049
Change 1 2-1084
TM 5-3805-254-20-2
INITIAL SETUP:
Front brake limiting and quick release valve to Lockwasher, quick release valve (two required)
brake treadle valve hose disconnected (page
2-1084) Tools/Test Equipment
Left front wheel to front brake limiting and quick re-
lease valve hose disconnected (page 2-1115) Goggles, safety
Right front wheel to front brake limiting and quick Wrench, box-end, 7/16-inch
release valve hose disconnected (page Wrench, open-end, 7/16-inch
1-1122).
Front brake limiting control valve hose and fitting Personnel Required
disconnected (page 2-1159).
One
Change 1 2-1084.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front brake limiting Two nuts (2), a. Using 7/16-inch open-end wrench and 7/16-inch
and quick release lockwashers (3), box-end wrench, unscrew, and take off.
valve (1) washers (4), and b. Get rid of lockwashers.
screws (5)
INSTALLATION
4. Front brake limiting Two nuts (2), new Screw in and tighten using 7/16-inch box-end
and quick release lockwashers (3), wrench and 7/16-inch open-end wrench.
valve (1) washers (4), and
screws (5)
TA702148
Change 1 2-1084.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
FRONT BRAKE LIMITING AND QUICK RELEASE VALVE TO BRAKE TREADLE VALVE HOSE
FRONT BRAKE LIMITING AND QUICK RELEASE VALVE TO BRAKE TREADLE VALVE HOSE -
CONTINUED
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front brake limiting Airhose (2) and Using 7/8-inch open-end wrench, unscrew
and quick release 90-degree elbow (3) and take off.
valve (1)
TA702149
Change 1 2-1085
TM 5-3805-254-20-2
FRONT BRAKE LIMITING AND QUICK RELEASE VALVE TO BRAKE TREADLE VALVE HOSE -
CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Left frame rail (1) Clamp (3), screw a. Using 7/16-inch box-end and 716-inch
and airhose (2) (4), lockwasher (5), open-end wrenches, unscrew and take
and nut (6) out.
b. Get rid of lockwasher.
c. Take clamp off airhose.
3. Engine side of Clamp (8), screw a. Using 7/16-inch box-end and 7/16-inch
firewall (7) and (9), lockwasher open-end wrenches, unscrew and take
airhose (2) (10), and nut (11) out.
b. Get rid of lockwasher.
c. Take clamp off airhose.
4. Brake treadle Line nut (13) and a. Using 7/8-inch open-end wrench, un-
valve (12) airhose (2) screw and take off.
b. Take out airhose.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1086
TM 5-3805-254-20-2
FRONT BRAKE LIMITING AND QUICK RELEASE VALVE TO BRAKE TREADLE VALVE HOSE -
CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
9. Brake treadle 45-degree elbow (14) Wrap pipe threads with antiseizing tape.
valve (12)
10. 45-degree elbow (14) Airhose (2) Screw on and tighten using 7/8-inch open-
end wrench.
11. Clamp bracket (15) Clamp (8), screw a. Put clamp on airhose (2).
(9), new lockwasher b. Aline holes in clamp and clamp bracket.
(10), and nut (11) c. Screw in and tighten using 7/16-inch
box-end and 7/16-inch open-end
wrenches.
TA244384
2-1087
TM 5-3805-254-20-2
FRONT BRAKE LIMITING AND QUICK RELEASE VALVE TO BRAKE TREADLE VALVE HOSE -
CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
12. Left frame rail (1) Clamp (2), screw a. Put clamp on airhose (6).
(3), new lockwasher b. Aline holes in clamp and left frame rail.
(4), and nut (5) c. Screw in and tighten using 7116-inch
box-end and 7/16-inch open-end
wrenches.
13. Front brake limit- 90-degree elbow (8) Wrap pipe threads with antiseizing tape.
ing and quick re-
lease valve (7)
NOTE
TA244385
Change 1 2-1088
TM 5-3805-254-20-2
INITIAL SETUP:
Front rear quick release valve to parking airbrake Lockwasher, quick release valve (two required)
chamber disconnected (page 2-1088.3).
Chassis T-fitting to front rear quick release valve Personnel Required
hose disconnected page 2-1146).
One
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
Change 1 2-1088.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front rear quick Two nuts (2), a Using 7/16-inch open-end wrench and 7/16-inch
release valve (1) lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b Get rid of lockwashers.
Front rear T-fitting (5) is also removed.
INSTALLATION
4. Front rear quick Two nuts (2), new Screw in and tighten using 7/16-inch box-end
release valve (1) lockwashers (3), wrench and 7/16-inch open-end wrench.
and screws (4) Front rear quick release valve (5) Is also
installed.
TA702150
Change 1 2-1088.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
FRONT REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
TA702151
Change 1 2-1089
TM 5-3805-254-20-2
FRONT REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Front rear quick Line nut (2) and Using 3/4-inch and 11/16-inch open-end
release valve (0.1) fitting (1) wrenches, unscrew and take off.
4. Right parking air- Line nut (7) and Using 3/4-inch and 5/8-inch open-end
brake chamber (5) fitting (6) wrenches, unscrew and take off.
5. Left parking air- Line nut (10), fitting a. Using 3/4-inch and 5/8-inch open-end
brake chamber (8) (9), and left airhose (11) wrenches, unscrew and take off.
b. Take out left airhose.
6. Clamp bracket (12) Screw (13), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (14), nut open-end wrenches, unscrew and take
(15), and two out.
clamps (16) b. Get rid of lockwasher.
c. Take clamp off right airhose (17) only.
d. Take out right airhose (17).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1090
TM 5-3805-254-20-2
FRONT REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA702152
Change 1 2-1091
TM 5-3805-254-20-2
FRONT REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
11. Left parking air- Fitting (2) Wrap pipe threads with antiseizing tape.
brake chamber (1)
12. Fitting (2) and left Screw on and tighten using 3/4-inch and
airhose (3) 5/8-inch open-end wrenches.
13. Right parking air- Fitting (5) Wrap pipe threads with antiseizing tape.
brake chamber (4)
14. Fitting (5) and Screw on and tighten using 3/4-inch and
right airhose (6) 5/8-inch open-end wrenches.
15. Front rear quick 45-degree elbow (8) Wrap pipe threads with antiseizing tape.
release valve (7)
18. Fitting (9) and left a. Screw on and tighten using 314-inch and
airhose (3) 11/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
Change 1 2-1092
TM 5-3805-254-20-2
FRONT REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
20. Clamp bracket (11) Clamp (10), clamp a. Allne holes In clamps and clamp
(12), screw (13), bracket.
new lockwasher (14), b. Screw In and tighten using 7/16-Inch
and nut (15) box-end and 7/16-Inch open-end
wrenches.
TA244388
Change 1 2-1093
TM 5-3805-254-20-2
INITIAL SETUP:
Front rear T-fitting to service airbrake chamber Lockwasher, T-manifold (two required)
hoses disconnected (page 2-1093.1).
Front relay valve to front rear T-fitting hose discon- Personnel Required
nected (page 2-1099).
One
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front rear Two nuts (2), a Using 7/16-inch open-end wrench and
7/16-inch
T-fitting (1) lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b Get rid of lockwashers.
Front rear quick release valve (5)
is also removed.
INSTALLATION
4. Front rear Two nuts (2), new Screw in and tighten using 7/16-inch box-end
T-fitting (1) lockwashers (3), wrench and 7/16-inch open-end wrench.
and screws (4) Front rear quick release valve (5)
is also Installed.
Change 1 2-1093.0
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA702153
Change 1 2-1093.1
TM 5-3805-254-20-2
INITIAL SETUP:
Materials/Parts One
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
4. Right service air- Line nut (10) and Using 3/4-inch and 5/8-inch open-end
brake chamber (8) fitting (9) wrenches, unscrew and take off.
Change 1 2-1094
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5. Left service air- Line nut (13) and a. Using 3/4-inch and 5/8-inch open-end
brake chamber (11) fitting (12) wrenches, unscrew and take off.
b. Take out left airhose (3).
6. Clamp bracket (14) Screw (15), lock- a. Using 7/16-inch box-end and 7116-inch
washer (16), nut open-end wrenches, unscrew and take
(17), and two out.
clamps (18) b. Get rid of lockwasher.
c. Take clamp off right airhose (2) only.
d. Take out right airhose (2).
TA244389
Change 1 2-1095
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1096
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
11. Left service air- Fitting (2) Wrap pipe threads with antiseizing tape.
brake chamber (1)
12. Fitting (2) and Screw on and tighten using 3/4-inch and
left airhose (3) 5/8-inch open-end wrenches.
13. Right service air- Fitting (5) Wrap pipe threads with antiseizing tape.
brake chamber (4)
14. Fitting (5) and Screw on and tighten using 3/4-inch and
right airhose (6) 5/8-inch open-end wrenches.
TA244390
Change 1 2-1097
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
15. Front rear 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
T-fitting (1)
17. 45-degree elbow (4) Wrap pipe threads with antiseizing tape.
20. Clamp bracket (7) Clamp (6), clamp a. Aline holes in clamps and clamp
(8), screw (9), new bracket.
lockwasher (10), b. Screw in and tighten using 7/16-inch
and nut (11) box-end and 7/16-inch open-end
wrenchs.
TA244391
Change 1 2-1098
TM 5-3805-254-20-2
INITIAL SETUP:
Double check valve T-fitting to front relay valve Tape, antiseizing (item 22, appendix C)
T-fitting hose disconnected (page 2-1149) Lockwasher, relay valve (two required)
Front relay valve to front rear T-fitting hose discon-
nected (page 2-1099) Personnel Required
Dry air reservoir to front relay valve hose discon-
nected (page 2-1080) One
Front relay valve T-fitting to rear relay valve hose
disconnected (page 2-1105).
Front relay valve to rear relay valve hose discon-
nected (page 2-1101).
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
Wrench, open-end, 3/4-inch
Change 1 2-1098.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front relay valve Two nuts (2), a Using 7/16-inch open-end wrench and 7/16-inch
(1) lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b Get rid of lockwashers.
3. Front relay valve T-fitting (6) Using 3/4-inch open-end wrench, unscrew, and take
(1) off.
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
4. Front relay valve T-fitting (6) a Wrap pipe threads with antiseizing tape (page
(1) 2-424).
b Screw in and tighten using 3/4-inch open-end
wrench.
6. Front relay valve Two nuts (2), new Screw in and tighten using 7/16-inch box-end wrench
(1) lockwashers (3), and 7/16-inch open-end wrench.
and screws (4)
Change 1 2-1098.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
1. Connect front relay valve to front rear relay valve hose (page
2-1101).
2. Connect front relay valve T-fitting to rear relay valve hose
(page 2-1105).
3. Connect dry air reservoir to front relay valve hose (page
2-1080).
4. Connect front relay valve to front rear T-fitting hose (page
2-1099).
5. Connect double check valve T-fitting to front relay valve
T-fitting hose (page 2-1149).
TA702154
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front relay valve (0.1) Line nut (2) and Using 7/8-inch open-end wrench, unscrew
90-degree elbow (1) and take off.
2. Front rear T-fitting Line nut (4) and a. Using 7/8-inch open-end wrench, unscrew,
(2.1) 45-degree elbow (3) and take off.
b. Take out airhose (5).
TA702155
Change 1 2-1099
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Front rear 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
T-fltting (1)
8. Front relay 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
valve (4)
Change 1 2-1100
TM 5-3805-254-20-2
INITIAL SETUP:
Materials/Parts One
TA244393
2-1101
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front relay valve (0.1) Line nut (2) and Using 1 1/4-inch open-end wrench, un-
45-degree elbow (1) screw and take off.
2. Rear relay valve Line nut (4) and Using 1 1/4-inch open-end wrench, un-
(2.1) 45-degree elbow (3) screw and take off.
NOTE
3. Clamp bracket (5) Screw (6), lock- a. Using 7/16-inch box-end and 7/16-inch
washer (7), nut (8), open-end wrenches, unscrew and take
and clamp (9) out.
b. Get rid of lockwasher.
c. Take clamps off airhose (10).
d. Take out airhose (10).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1102
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
TA702156
Change 1 2-1103
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
8. Rear relay 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
valve (1)
10. Front relay 45-degree elbow (5) Wrap pipe threads with antiseizing tape.
valve (4)
NOTE
13. Clamp bracket (9) Clamp (8), screw a. Aline holes in clamp and clamp bracket.
(10), new lock- b. Screw in and tighten using 7/16-inch
washer (11), and box-end and 7/16-inch open-end
nut (12) wrenches.
TA244395
Change 1 2-1104
TM 5-3805-254-20-2
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front relay valve Line nut (2) and Using 7/8-inch and 3/4-inch open-
T-fitting (1) fitting (3) end wrenches, unscrew and take
off.
TA702157
Change 1 2-1105
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Rear relay valve (9) Line nut (2) and Using 7/8-inch open-end wrench, unscrew
90-degree elbow (1) and take off.
NOTE
3. Clamp bracket (3) Screw (4), lock- a. Using 7/16-inch box-end and 7116-inch
washer (5), nut (6), open-end wrenches, unscrew and take
and clamp (7) out.
b. Get rid of lockwasher.
c. Take clamp off airhose (8).
d. Take out airhose (8).
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1106
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
8. Rear relay valve (9) 90-degree elbow (1) Wrap pipe threads with antiseizing tape.
9. 90-degree elbow (1) 90-degree elbow (1) Screw on and tighten using 7/8-inch open-
and line nut (2) end wrench.
10. Front relay Front relay valve T-fitting Wrap pipe threads with antiseizing tape.
valve (10) (11) and fitting (11.1)
11. Front relay valve T-fitting Screw on and tighten using 718-inch and
(11), fitting (11.1), and line 3/4-inch open-end wrenches.
nut (12)
Change 1 2-1107
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
NOTE
13. Clamp bracket (3) Clamp (2), a. Aline holes in clamp and clamp bracket.
screw (4), new b. Screw in and tighten using 7/16-inch
lockwasher (5), box-end and 7/16-inch open-end
and nut (6) wrenches.
TA244398
2-1108
TM 5-3805-254-20-2
INITIAL SETUP:
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Cab floor through- Line nut (2) Using 3/4-inch open-end wrench,
connector 45-degree unscrew
elbow (1) and take off.
2. Double check valve (5) Line nut (4) and Using 3/4-inch open-end wrench,
90-degree elbow (3) unscrew
and take off.
TA702159
Change 1 2-1109
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
NOTE
4. Driver’s seat Line nut (7) and a. Using 9/16-inch open-end wrench, un-
valve assembly (6) air line (8) screw and take off.
b. Move air line out of way.
5. Left side rear Eight screws (10), a. Using number two cross-tip screw-
cab wall (9) eight flat washers driver, unscrew and take out.
(11), and left b. Push air line (8) through hole while
lower rear taking off left lower rear molding.
molding (12) Be careful not to bend or crimp
air line.
6. Cab floor through- Line nut (14) and a. Using 5/8-inch open-end wrench, un-
connector 90-degree air line (15) screw and take off.
elbow (13) b. Move air line out of way.
TA244400
2-1110
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8. Under cab floor (16) Cab floor through- Using 9/16-inch open-end wrench, un-
connector 45-degree screw and take off.
elbow (17)
NOTE
9. Top of cab floor Anchor coupling Using 1 1/8-inch and 1-inch open-end
(18) and under cab (19), flat washer wrenches, unscrew and take out.
floor (16) (20), and nut (21)
TA244401
2-1111
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
11. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1112
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
14. Top of cab floor (1) Anchor coupling (2) Put in.
NOTE
15. Anchor coupling (2) Flat washer (3) and Screw on and tighten using 1 1/8-inch and
nut (4) 1-inch open-end wrenches.
16. Cab floor through- a. Wrap both male pipe threads with anti-
connector 90-degree seizing tape.
elbow (5) b. Screw in and tighten using 9/16-inch
open-end wrench.
Position to face left cab door.
17. Cab floor through- Air line (6) Screw on and tighten using 5/8-inch open-
connector 90-degree end wrench.
elbow (5)
18. Left side rear cab Air line (8) and a. Push air line through hole in left lower
wall (7) left lower rear rear molding.
molding (9) b. Put left lower rear molding in position.
19. Left lower rear Eight screws (10) Screw in and tighten using number two
molding (9) and eight flat cross-tip screwdriver.
washers (11)
TA244402
2-1113
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
WARNING
Safety gogles must be worn when working under truck to prevent eye injury.
20. Anchor coupling (1) Cab floor through- a. Wrap both male pipe threads with anti-
connector 45-degree seizing tape.
elbow (2) b. Screw in and tighten using 9/16-inch
open-end wrench.
Position to face left side cab door.
21. Cab floor through Airhose (3) Screw on and tighten using 3/4-inch open-
connector 45-degree end wrench.
elbow (2)
22. Double check 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
valve (4)
NOTE
25. Clamp bracket (7) Clamp (6), screw a. Aline holes in clamp and clamp bracket.
(8), new lockwasher b. Screw in and tighten using 7/16-inch
(9), and nut (10) box-end and 7/16-inch open-end
wrenches.
Change 1 2-1114
TM 5-3805-254-20-2
NOTE
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES
INITIAL SETUP:
2-1115
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
3. T-fitting (5) Line nut (6) and a. Using 3/4-inch open-end wrench, un-
airhose (2) screw and take off.
b. Take out airhose.
6. T-fitting (5) Line nut (11) and a. Using 3/4-inch open-end wrench, un-
airhose (8) screw and take off.
b. Take out airhose.
8. Fitting (14) Line nut (15) Using 3/4-inch and 5/8-inch open-end
wrenches, unscrew and take off.
9. Fitting (16) Line nut (17) and a. Using 3/4-inch and 11/16-inch open-
airhose (13) end wrenches, unscrew and take off.
b. Take out airhose.
12. Front brake limiting Line nut (22), fitting a. Using 1-inch and 7/8-inch open-end
and quick release (21), and airhose wrenches, unscrew and take off.
valve (20.1) (19) b. Take out airhose.
Change 1 2-1116
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
13. Anchor coupling (23) Fitting (14) Using 1-inch and 5/8-inch open-end
wrenches, unscrew and take out.
15. Bracket (12) Anchor coupling a. Using 1 1/8-inch and 1-inch open-end
(23), lockwasher wrenches, unscrew and take out.
(24), and nut (25) b. Get rid of lockwasher.
16. Anchor coupling (26) Fitting (16) Using 1 18-inch and 11/16-inch open-end
wrenches, unscrew and take out.
18. Left frame Anchor coupling a. Using 1 7/16-inch and 1 1/8-inch open-
rail (27) (26), lockwasher end wrenches, unscrew and take out.
(28), and nut (29) b. Get rid of lockwasher.
TA702160
Change 1 2-1117
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for type #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
19. Four airhoses Clean using liquid detergent and wiping rag.
20. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1118
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
24. Anchor coupling (2) New lockwasher (3) Screw on and tighten using 1 7/16-inch and
and nut (4) 1 1/8-inch open-end wrenches.
25. 90-degree elbow (5) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 3/4-inch
open-end wrench.
Position to face front of truck.
28. Anchor coupling (8) New lockwasher (9) Screw on and tighten using 1 1/8-inch and
and nut (10) 1-inch open-end wrenches.
TA244405
2-1119
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
31. Front brake limiting Fitting (2) Wrap pipe threads with antiseizing tape.
and quick release
valve (1)
32. Fitting (2) and Screw on and tighten using 1-inch and 7/8-
airhose (3) inch open-end wrenches.
33. Left frame rail (4) 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
34. 90-degree elbow (5) Airhose (3) a. Screw on and tighten using 1-inch open-
end wrench.
b. Take off tag.
c. Get rid of tag.
35. Left frame rail (4) Fitting (6) Wrap pipe threads with antiseizing tape.
36. Fitting (6) Airhose (7) Screw on and tighten using 3/4-inch and
11/16-inch open-end wrenches.
37. Bracket (8) Fitting (9) Wrap pipe threads with antiseizing tape.
38. Fitting (9) Airhose (7) a. Screw on and tighten using 314-inch and
5/8-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
39. Front airbrake Fitting (11) Wrap pipe threads with antiseizing tape.
chamber (10)
40. Fitting (11) and Screw on and tighten using 3/4-inch and
airhose (12) 5/8-inch open-end wrenches.
41. Bracket (8) T-fitting (13) Wrap pipe threads with antiseizing tape.
42. T-fitting (13) Airhose (12) a. Screw on and tighten using 3/4-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
43. Rear airbrake 45-degree elbow (15) Wrap pipe threads with antiseizing tape.
chamber (14)
Change 1 2-1120
TM 5-3805-254-20-2
LEFT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
45. Bracket (8) T-fitting (13) Wrap pipe threads with antiseizing tape.
46. T-fitting (13) Airhose (16) a. Screw on and tighten using 3/4-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
NOTE
FOLLOW-ON MAINTENANCE:
TA702161
Change 1 2-1121
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES
INITIAL SETUP:
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1122
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
3. T-fitting (5) Line nut (6) and a. Using 3/4-inch open-end wrench, un-
airhose (2) screw and take off.
b. Take out airhose.
6. T-fitting (5) Line nut (11) and a. Using 3/4-inch open-end wrench, un-
airhose (8) screw and take off.
b. Take out airhose.
8. Fitting (14) Line nut (15) Using 3/4-inch and 518-inch open-end
wrenches, unscrew and take off.
9. Fitting (16) Line nut (17) and a. Using 3/4-inch and 11/16-inch open-
airhose (13) end wrenches, unscrew and take off.
b. Take out airhose.
TA244407
Change 1 2-1123
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
12. Front brake limiting Line nut (5) and Using 1-inch and 7/8-inch open-end
and quick release fitting (4) wrenches, unscrew and take off.
valve (3.1)
NOTE
13. Front cross- Screw (7), lock- a. Using 7/16-inch box-end and 7/16-inch
member (6) washer (8), nut (9), open-end wrenches, unscrew and take
and clamp (10) out.
b. Get rid of lockwasher.
c. Take clamp off airhose (2).
14. Right frame Screw (12), lock- a. Using 7/16-inch box-end and 7/16-inch
rail (11) washer (13), nut (14), open-end wrenches, unscrew and take
and clamp (15) out.
b. Get rid of lockwasher.
c. Take clamp off airhose (2).
d. Take out airhose.
TA702162
Change 1 2-1124
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
15. Anchorcoupling (16) Fitting (17) Using 1-inch and 5/8-inch open-end
wrenches, unscrew and take out.
17. Bracket (19) Anchor coupling a. Using 1 1/8-inch and 1-inch open-end
(16), lockwasher wrenches, unscrew and take out.
(20), and nut (21) b. Get rid of lockwasher.
18. Anchor coupling (22) Fitting (23) Using 1 11/8-inch and 11/16-inch open-end
wrenches, unscrew and take out.
20. Right frame Anchor coupling a. Using 1 7/16-inch and 1 118-inch open-
rail (11) (22), lockwasher end wrenches, unscrew and take out.
(24), and nut (25) b. Get rid of lockwasher.
TA244409
2-1125
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F (38°C)
and for typo #2 is 138°F (59°C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
21. Four airhoses Clean using liquid detergent and wiping rag.
22. All metal parts Clean using drycleaning solvent and wiping
rag.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1126
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
WARNING
Safety gogles must be worn when working under truck to prevent eye injury.
25. Right frame rail (1) Anchor coupling (2) Put in.
26. Anchor coupling (2) New lockwasher (3) Screw on and tighten using 1 7/16-inch and
and nut (4) 1 1/8-inch open-end wrenches.
27. 90-degree elbow (5) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 3/4-inch
open-end wrench.
Position to face front of truck.
30. Anchor coupling (8) New lockwasher (9) Screw on and tighten using 1 1/8-inch and
and nut (10) 1-inch open-end wrenches.
TA244410
2-1127
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
33. Front brake limiting Fitting (2) Wrap pipe threads with antiseizing tape.
and quick release
valve (1)
34. Fitting (2) and Screw on and tighten using 1-inch and 7/8-
airhose (3) inch open-end wrenches.
36. Right frame rail (5) 90-degree elbow (6) Wrap pipe threads with antiseizing tape.
37. 90-degree elbow (6) Airhose (3) a. Screw on and tighten using 1-inch open-
end wrench.
b. Takeoff tag.
c. Get rid of tag.
NOTE
39. Right frame rail (5) Clamp (7), screw a. Aline holes.
and front cross- (9), new lockwasher b. Screw in and tighten using 7116-inch
member (8) (10), and nut (11) box-end and 7/16-inch open-end
wrenches.
40. Right frame rail (5) Fitting (12) Wrap pipe threads with antiseizing tape.
41. Fitting (12) Airhose (13) Screw on and tighten using 3/4-inch and
11/16-inch open-end wrenches.
42. Bracket (14) Fitting (15) Wrap pipe threads with antiseizing tape.
Change 1 2-1128
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES -
CONTINUED
ACTION
LOCATION ITEM REMARKS
43. Fitting (15) Airhose (13) a. Screw on and tighten using 3/4-inch and
5/8-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
44. Front airbrake 45-degree elbow (17) Wrap pipe threads with antiseizing tape.
chamber (16)
45. 45-degree elbow (17) Screw on and tighten using 3/4-inch open-
and airhose (18) end wrench.
46. Bracket (15) T-fitting (19) Wrap pipe threads with antiseizing tape.
47. T-fitting (19) Airhose (18) a. Screw on and tighten using 3/4-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag.
TA244411
Change 1 2-1129
TM 5-3805-254-20-2
RIGHT FRONT WHEEL TO FRONT BRAKE LIMITING AND QUICK RELEASE VALVE HOSES CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
48. Rear airbrake Fitting (2) Wrap pipe threads with antiseizing tape.
chamber (1)
49. Fitting (2) and Screw on and tighten using 3/4-inch open-
airhose (3) end wrench.
50. Bracket (4) T-fitting (5) Wrap pipe threads with antiseizing tape.
51. T-fitting (5) Airhose (3) a. Screw on and tighten using 3/4-inch
open-end wrench.
b. Take off tag.
c. Get rid of tag
NOTE
FOLLOW-ON MAINTENANCE:
Change 1 2-1130
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
Steps 1 and 2 are typical to remove only one or both quick release valves.
1. Rear rear quick Two nuts (2), a. Using 7/16-Inch open-end wrench and 7/16-inch
release valve (1) lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b. Get rid of lockwashers.
TA702163
Change 1 2-1130.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSTALLATION
NOTE
Steps 3 and 4 are typical to install only one or both quick release valves.
4. Rear rear quick Two nuts (3), new Screw in and tighten using 7/16-inch box-end
release valve (2) lockwashers (4), wrench and 7/16-inch open-end wrench.
and screws (5)
NOTE
FOLLOW-ON MAINTENANCE: Connect parking and service airbrake hoses as required (page 2-1131, 2-
1136, 2-1140.3, and 2-1157).
TA702164
Change 1 2-1130.2
TM 5-3805-254-20-2
INITIAL SETUP
2-1131
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
4. Right parking air- Fitting (9), line Using 3/4-inch and 518-inch open-end
brake chamber (8) nut (10), and right wrenches, unscrew and take off.
airhose (2)
5. Left parking air- Fitting (12), line Using 3/4-inch and 5/8-inch open-end
brake chamber (11) nut (13), and left wrenches, unscrew and take off.
airhose (3)
NOTE
6. Right airhose (2) Two clamps (14), a. Using 7/16-inch box-end and 7/16-inch
and left airhose (3) screw (15), lock- open-end wrenches, unscrew and take
washer (16), and out.
nut (17) b. Get rid of lockwasher.
c. Take clamps off right airhose (2) and left
airhose (3).
d. Take out right airhose (2) and left
airhose (3).
Change 1 2-1132
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent PD680 is toxic and flammable. Wear protective safety goggles and gloves and use
only In a well ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
TA244413
2-1133
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
11. Left parking air- Fitting (2) Wrap pipe threads with antiseizing tape.
brake chamber (1)
12. Fitting (2) Left airhose (3) Screw on and tighten using 3/4-inch and
5/8-inch open-end wrenches.
13. Right parking air- Fitting (5) Wrap pipe threads with antiseizing tape.
brake chamber (4)
14. Fitting (5) Right airhose (6) Screw on and tighten using 3/4-inch and
5/8-inch open-end wrenches.
15. Rear rear quick Fitting (8) Wrap pipe threads with antiseizing tape.
release valve (7)
16. Fitting (8) and a. Screw on and tighten using 3/4-inch and
left airhose (3) 11/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
Change 1 2-1134
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO PARKING AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
18. Fitting (9) and a. Screw on and tighten using 3/4-inch and
right airhose (6) 11/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
NOTE
19. Left airhose (3) and Two clamps (10) Put on.
right airhose (6)
20. Clamp bracket (11) Two clamps (10), a. Aline holes in clamps and clamp
screw (12), new bracket.
lockwasher (13), b. Screw in and tighten using 7/16-inch
and nut (14) box-end and 7/16-inch open-end
wrenches.
TA244414
Change 1 2.1135
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1136
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO SERVICE AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
4. Right service air- Fitting (9), line Using 3/4-inch and 5/8-inch open-end
brake chamber (8) nut (10), and wrenches, unscrew and take off.
right airhose (2)
5. Left service air- Fitting (12), line Using 3/4-inch and 5/8-inch open-end
brake chamber (11) nut (13), and left wrenches, unscrew and take off.
airhose (3)
NOTE
6. Right airhose (2) Two clamps (14), a. Using 7/16-inch box-end and 7/16-inch
and left airhose (3) screw (15), lock- open-end wrenches, unscrew and take
washer (16), and out.
nut (17) b. Get rid of lockwasher.
c. Take clamps off right airhose (2) and left
airhose (3).
d. Take out right airhose (2) and left
airhose (3).
TA702165
Change 1 2-1137
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO SERVICE AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1138
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO SERVICE AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
11. Left service air- Fitting (2) Wrap pipe threads with antiseizing tape.
brake chamber (1)
12. Fitting (2) Left airhose (3) Screw on and tighten using 3/4-inch and
5/8-inch open-end wrenches.
13. Right service air- Fitting (5) Wrap pipe threads with antiseizing tape.
brake chamber (4)
14. Fitting (5) Right airhose (6) Screw on and tighten using 314-inch and
5/8-inch open-end wrenches.
15. Rear rear quick Fitting (8) Wrap pipe threads with antiseizing tape.
release valve (7)
16. Fitting (8) and a. Screw on and tighten using 3/4-inch and
left airhose (3) 11/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
18. Fitting (9) and a. Screw on and tighten using 3/4-inch and
right airhose (6) 11/16-inch open-end wrenches.
b. Take off tag.
c. Get rid of tag.
TA244416
Change 1 2.1139
TM 5-3805-254-20-2
REAR REAR QUICK RELEASE VALVE TO SERVICE AIRBRAKE CHAMBER HOSES - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
NOTE
19. Left airhose (1) and Two clamps (3) Put on.
right airhose (2)
20. Clamp bracket (4) Two clamps (3), a. Aline holes in clamps and clamp
screw (5), new lock- bracket.
washer (6), and b. Screw in and tighten using 7/16-inch
nut (7) box-end and 7/16-inch open-end
wrenches.
TA244417
Change 1 2-1140
TM 5-3805-254-20-2
INITIAL SETUP
Front relay valve T-fitting to rear relay valve hose Lockwasher, relay valve (two required)
disconnected (page 2-1105).
Rear relay valve to rear rear quick release valve Personnel Required
hose disconnected (page 2-1140.3).
Front relay valve to rear relay valve hose discon- One
nected (page 2-1101).
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
Change 1 2-1140.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Rear relay valve (1) Two nuts (2), a. Using 7/16-inch open-end wrench and 7/16-inch
lockwashers (3), box-end wrench, unscrew, and take off.
and screws (4) b. Get rid of lockwashers.
INSTALLATION
4. Rear relay valve (1) Two nuts (2), new Screw in and tighten using 7/16-inch box-end
lockwashers (3), wrench and 7/16-inch open-end wrench.
and screws (4)
TA702166
Change 1 2-1140.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
REAR RELAY VALVE TO REAR REAR QUICK RELEASE VALVE HOSE - CONTINUED
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Rear relay valve (1) Line nut (2) and Using 7/8-inch open-end wrench, unscrew
45-degree elbow (2.1) and take off.
2. Rear rear quick Line nut (4), airhose a. Using 7/8-inch open-end wrench, un-
release valve (3) (5), 90-degree elbow screw and take off.
(6), and adapter (7) b. Take out airhose.
Change 1 2-1141
TM 5-3805-254-20-2
REAR RELAY VALVE TO REAR REAR QUICK RELEASE VALVE HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Rear rear quick 90-degree elbow (2) and Wrap pipe threads with antiseizing tape.
release valve (1) adapter (2.1)
Change 1 2-1142
TM 5-3805-254-20-2
REAR RELAY VALVE TO REAR REAR QUICK RELEASE VALVE HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
8. Rear relay valve (4) 45-degree elbow (5) Wrap pipe threads with antiseizing tape.
INITIAL SETUP
Tools Materials/Parts
TA702168
Change 1 2-1143
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Chassis T-fitting (7) Line nut (2) and Using 3/4-inch and 5/8-inch open-end
fitting (1) wrenches, unscrew and take off.
2. Double check valve Line nut (4), airhose a. Using 3/4-inch open-end wrench, un-
(6) (5), and 45-degree screw and take off.
elbow (3) b. Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1144
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Double check 45-degree elbow (3) Wrap pipe threads with antiseizing tape.
valve (6)
TA244420
Change 1 2-1145
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Chassis T-fitting (0.1) Line nut (2) and Using 3/4-inch and 5/8-inch open-end
fitting (1) wrenches, unscrew and take off.
2. Front rear quick release Line nut (4), airhose a. Using 3/4-inch open-end wrench, un-
valve (2.1) (5), and 45-degree screw and take off.
elbow (3) b. Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1146
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA702169
Change 1 2-1147
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Front rear quick 45-degree elbow (2) Wrap pipe threads with antiseizing tape.
release valve (1)
9. Fitting (5) and line Screw on and tighten using 3/4-inch and
nut (6) 5/8-inch open-end wrenches.
TA244658
Change 1 2-1148
TM 5-3805-254-20-2
INITIAL SETUP
Chassis T-fitting to double check valve hose dis- Tape, antiseizing (item 22, appendix C)
connected (page 2-1143). Lockwasher, double check valve
Cab floor through connector to double check
valve hose disconnected (page 2-1108). Personnel Required
Goggles, safety
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch
Wrench, open-end, 3/4-inch (two required)
Change 1 2-1148.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Fitting (1) Line nut (2) and a. Using two 3/4-inch open-end wrenches,
air hose (3) unscrew, and take off.
b. Move air hose out of way.
2. Double check valve (4) Fitting (1) Using 3/4-inch open-end wrench, unscrew, and take
off.
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Double check valve Nut (5), lockwasher Screw in and tighten using 7/16-inch box-end wrench
(4) (6), and screw (7) and 7/16-inch open-end wrench.
8. Fitting (1) Line nut (2) Screw on and tighten using two 3/4-inch open-end
and air hose (3) wrenches.
Change 1 2-1148.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1. Front relay valve Line nut (2) and Using 7/8-inch open-end wrench,
T-fitting (1) 45-degree elbow (3) unscrew
and take off.
TA702171
Change 1 2-1149
TM 5-3805-254-20-2
DOUBLE CHECK VALVE T-FITTING TO FRONT RELAY VALVE T-FITTING HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Double check valve Line nut (2) and a. Using 7/8-inch open-end wrench, un-
T-fitting (1) airhose (3) screw and take off.
b. Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
6. Front relay valve 45-degree elbow Wrap pipe threads with antiseizing tape.
T-fitting (5) (5.1)
Change 1 2-1150
TM 5-3805-254-20-2
DOUBLE CHECK VALVE T.FITTING TO FRONT RELAY VALVE T-FITTING HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
7 Front relay valve 45-degree elbow (5.1) Screw on and tighten using 7/8-inch open-
T-fitting (5) and line nut (6) end wrench.
9 Double check valve Line nut (2) Screw on and tighten using 7/8-inch open-
T-fitting (1) end wrench.
Change 1 2-1151
TM 5-3805-254-20-2
INITIAL SETUP
Goggles, safety
Wrench, box-end, 7/16-inch
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 Left frame rail (1) Screw (2) and a Using 7/16-inch box-end wrench, unscrew, and
lockwasher (3) take off.
b Get rid of lockwasher.
INSTALLATION
3 Left frame rail (1) Chassis 90-degree Put in place.
elbow (4)
4 Screw (2) and new Screw in and tighten using 7/16-inch box-end
lockwasher (3) wrench.
Change 1 2-1151.0
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA702173
Change 1 2-1151.1
TM 5-3805-254-20-2
CHASSIS T-FITTING
INITIAL SETUP
Tools/Test Equipment
Goggles, safety
Wrench, box-end, 7/16-inch
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 Left frame rail (1) Screw (2) and a Using 7/16-inch box-end wrench, unscrew, and
lockwasher (3) take off.
b Get rid of lockwasher.
INSTALLATION
3 Left frame rail (1) Spacer (4) and Put in place.
chassis T-fitting (5)
4 Screw (2) and new Screw in and tighten using 7/16-inch box-end
lockwasher (3) wrench.
Change 1 2-1151.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE:
TA702174
Change 1 2-1151.3
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 Chassis T-fitting (7) Line nut (2) and Using 3/4-inch open-end wrench, unscrew
45-degree elbow (1) and take off.
2 Chassis 90-degree Line nut (4), airhose a Using 3/4-inch and 11/16-inch open-
(6) (5), and fitting (3) end wrenches, unscrew and take off.
b Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1152
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-424).
8 Chassis 90-degree Fitting (3) Wrap pipe threads with antiseizing tape.
elbow (6)
8 Chassis 45-degree elbow (1) Wrap pipe threads with antiseizing tape.
T-fitting (7)
Change 1 2-1153
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 90-degree elbow (1) Line nut (2) Using 1-inch open-end wrench, unscrew
and take off.
2 90-degree elbow (3) Line nut (4) and a Using 1-inch open-end wrench, un-
airhose (5) screw and take off.
b Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-1154
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244425
2-1155
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from
seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-424).
6 Air dryer (1) 90-degree elbow (2) Wrap pipe threads with antiseizing tape.
7 90-degree elbow (2) Line nut (3) Screw on and tighten using 1-inch open-
end wrench.
8 Wet air 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
reservoir (4)
9 90-degree elbow (5) Line nut (6) Screw on and tighten using 1-inch open-
end wrench.
TA244426
2-1156
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
1 Chassis 90-degree Line nut (2) and Using 3/4-inch and 11/16-inch open-end
elbow (0.1) fitting (1) wrenches, unscrew and take off.
TA702175
2-1157
TM 5-3805-254-20-2
CHASSIS 90-DEGREE ELBOW TO REAR REAR QUICK RELEASE VALVE HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2 Rear rear quick Line nut (2), a Using 3/4-inch open-end wrench, un-
release valve (4) 90-degree elbow (1), screw and take off.
and adapter (4.1) b Take out airhose.
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from
seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-424).
6 Rear rear quick 90-degree elbow (1) Wrap pipe threads with antiseizing tape.
release valve (4) and adapter (4.1)
Change 1 2-1158
TM 5-3805-254-202
CHASSIS 90-DEGREE ELBOW TO REAR REAR QUICK RELEASE VALVE HOSE - CONTINUED
ACTION
LOCATION ITEM REMARKS
9 Fitting (6) Line nut (7) Screw on and tighten using 3/4-inch and
11/16-inch open-end wrenches.
TA702176
Change 1 2-1159
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn when working under truck to prevent eye injury.
NOTE
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
Change 1 2-1160
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8 90-degree elbow (14) Line nut (15) Using 9/16inch open-end wrench, un-
screw and take off.
9 Front brake limiting Line nut (17) and Using 9/16-inch open-end wrench, un-
and quick release 90-degree elbow (16) screw and take off.
valve (12)
10 Two clamp Two screws (19), two a Using 7/16-inch box-end and 7/16-inch
brackets (18) lockwashers (20), two open-end wrenches, unscrew and take
nuts (21), and two out.
clamps (22) b Get rid of lockwashers.
TA244429
Change 1 2-1161
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED -_
13 Engine side of 90-degree elbow (4) Using 1/2-inch open-end wrench, unscrew
firewall (3) and take out.
NOTE
14 Driver’s side of Nut (5), two lock- a Using 1 1/8-inch and 1-inch open-end
firewall (1) and washers (6), and wrenches, unscrew and take out.
engine side of anchor coupling (7) b Get rid of lockwashers.
firewall (3)
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only in a well-
ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use near open flame or
excessive heat The flashpoint for type #1 drycleaning solvent is 1000F (380C) and for type #2 is 138°F (590C) If you
become dizzy while using cleaning solvent, get fresh air immediately, and get medical aid If contact with eyes is made,
flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
2-1162
TM 5-3805-254-20-2
FRONT BRAKE LIMITING CONTROL VALVE HOSES AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
Replace all damaged or defective parts.
For more Information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244430
2-1163
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-424).
20 Engine side of 90-degree elbow (6) a Wrap pipe threads with antiseizing tape.
firewall (1) b Screw in and tighten using 1/2-inch
open-end wrench.
Position to face up.
21 Driver’s side of Fitting (7) a Wrap pipe threads with antiseizing tape.
firewall (2) b Screw in and tighten using 7116-inch
box-end wrench.
22 Engine side of 90-degree elbow (6) Wrap pipe threads with antiseizing tape.
firewall (1)
23 90-degree elbow (6) Airhose (8) Screw on and tighten using 9116-inch open-
end wrench.
24 Front brake limit- 90-degree elbow (10) Wrap pipe threads with antiseizing tape.
ing and quick re-
lease valve (9)
Change 1 2-1164
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
27 Two clamp Two clamps (11), two a Aline holes in clamps and clamp
brackets (12) screws (13), two new brackets.
lockwashers (14), b Screw in and tighten using 7/16-inch
and two nuts (15) box-end and 7/16-inch open-end
wrenches.
28 Driver’s side of Fitting (7) Wrap pipe threads with antiseizing tape.
firewall (2)
29 Fitting (7) Airhose (16) Screw on and tighten using 9116-inch and
7116-inch open-end wrenches.
30 Front brake 90-degree elbow (18) Wrap pipe threads with antiseizing tape.
limiting control
valve (17)
Change 1 2-1165
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
32 Right manifold (1) T-fitting (2) Wrap pipe threads with antiseizing tape.
33 T-fitting (2) Airhose (3) Screw on and tighten using 9/16-inch open-
end wrench.
34 Front brake 90-degree elbow (5) Wrap pipe threads with antiseizing tape.
limiting control
valve (4)
NOTE
FOLLOW-ON MAINTENANCE:
Page Page
FRONT WHEEL
INITIAL SETUP
Handle, hinged, 3/4-inch drive If air pressure gage shows less than normal
Socket, 1 112-inch, 3/4-inch drive pressure, start dump truck to build up
Truck, wheel, lift air pressure Shut down when air
Wrench, torque, 0 to 600 ft lb pressure builds up to between 90 and
(0 to 814 N.m) 125 psi (TM 5-3805-254-10).
Dump truck jacked and supported
Personnel Required (page 2-424).
Two References
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for right and left front wheels.
Assistant must apply dump truck brakes to allow loosening of lug nuts.
Lug nuts on right side of dump truck have right-hand threads and lug nuts on left side of
dump truck have left-hand threads.
Change 1 2-1168
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
1 Ten hub studs (1) Ten lug nuts (2) Using 1 1/2-inch, 3/4-inch drive socket
and hinged handle, unscrew and take off.
NOTE
2 Front hub (3) Wheel (4) a Position wheel lift truck underneath.
b Raise wheel lift truck to support weight of
wheel.
c Using wheel lift truck, pull off wheel.
d Lower wheel lift truck and take off wheel.
DISASSEMBLY/REPAIR/ASSEMBLY
NOTE
INSTALLATION
NOTE
INSTALLATION Steps given are typical for right and left front wheels.
TA244433
Change 1 2-1169
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
NOTE
3 Ten hub studs (1) Wheel (2) a Put on wheel lift truck.
b Raise wheel lift truck and put in position.
c Aline holes in wheel with ten hub studs
and push into place.
d Lower wheel lift truck.
NOTE
Assistant must apply dump truck brakes to allow tightening of lug nuts.
Lug nuts on right side of dump truck have right-hand threads and lug nuts on left side of dump truck have left-
hand threads.
NOTE
FOLLOW-ON MAINTENANCE: Dump truck lowered and supports removed (page 2-424).
TA244434
2-1170
TM 5-3805-254-20-2
REAR WHEEL
INITIAL SETUP
Handle, hinged, 3/4-inch drive If air pressure gage shows less than normal
Socket, square, 13/16-inch, 3/4- pressure, start dump truck to build up air
inch drive pressure Shut down when air pressure
Wrench, torque, 0 to 600 ft lb builds up to between 90 and 125 psi.
(0 to 814 N.m) (TM 5-3805-254-10).
Socket, 1 1/2-inch, 314-inch drive Dump truck jacked and supported
Truck, lift, wheel (page 2-424).
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for right and left front rear and rear rear wheels.
Engage parking brake (TM 5-3805-254-10) or have assistant apply dump truck brakes to allow loosening of lug nuts
and wheel studs.
Lug nuts and wheel studs on right side of dump truck have right-hand threads and lug nuts and wheel studs on left
side of dump truck have left-hand threads.
Change 1 2-1171
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
NOTE
1 Ten wheel studs (1) Ten lug nuts (2) Using 1 1/2-inch, 3/4-inch drive socket
and hinged handle, unscrew and take off.
NOTE
2 Rear hub (3) Outer wheel (4) a Position wheel lift truck underneath.
b Raise wheel lift truck to support weight of
wheel.
c Using wheel lift truck, pull off wheel.
d Lower wheel lift truck and take off
wheel.
3 Ten hub studs (5) Ten wheel studs (1) Using 13/16-inch, 3/4-inch drive square
socket and hinged handle, unscrew and take
off.
NOTE
4 Rear hub (3) Inner wheel (6) a Position wheel lift truck underneath.
b Raise wheel lift truck to support weight of
wheel.
c Using wheel lift truck, pull off wheel.
d Lower wheel lift truck and take off wheel.
Change 1 2-1172
TM 5-3805-254-20-2
REAR WHEEL - CONTINUED
INSTALLATION
NOTE
Steps given are typical for right and left front rear and rear rear wheels.
Engage parking brake (TM 5-3805-254-10) or have assistant apply dump truck brakes to allow tightening
of lug nuts and wheel studs.
Lug nuts and wheel studs on right side of dump truck have right-hand threads and lug
nuts and wheel studs on left side of dump truck have left-hand threads.
TA244435
2-1173
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
5 Ten hub studs (1) Inner wheel (2) a Put on wheel lift truck.
b Raise wheel lift truck and put in position.
c Aline holes in wheel with ten hub studs
and push into place.
d Lower wheel lift truck.
CAUTION
Always tighten the inner nuts 50 foot pounds (68 N.m) more than the outer nuts and never let the outer nuts
get below 400 foot pounds (542 N.m).
7 Ten wheel studs (3) Outer wheel (4) a Put on wheel truck.
b Raise wheel lift truck and put in position.
c Aline holes in wheel with ten wheel studs
and push into place.
d Lower wheel lift truck.
2-1174
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE: Dump truck lowered and supports removed (page 2-424).
INITIAL SETUP
TA244436
2-1175
TM 5-3805-254-20-2
REMOVAL
NOTE
Steps given are typical for right and left front hubs.
1 Front hub (1) Turn and check for drag caused by binding
brakes.
If drag is felt, perform steps 2, 3,
and 4.
If no drag is felt, go to step 5.
NOTE
Both front and rear brake adjusters must be taken out of adjustment.
Steps given are typical for front and rear brake adjusters.
2 Dust shield (2) Cover (3) Using 3/8-inch flat-tip screwdriver, pry
out.
3 Adjuster slot (4) Brake adjuster (5) Using brake adjusting tool, loosen enough
to allow front hub to move freely.
5 Grease cap (6) Plug (7) a Turn front hub to position plug at bottom.
b Place drain pan underneath.
c Using 5/16-inch hex wrench, unscrew
and take out.
d Allow oil to drain.
e Screw in hand tight.
f Get rid of drained oil (page 2-424).
2-1176
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
8 Adjusting nut (11) Cotter pin (12) a Using 8-inch roundnose pliers, bend
back ends and take out.
b Get rid of.
9 Front hub (1) Adjusting nut (11) Using adjustable wrench, unscrew and take
and washer (13) off.
TA24437
2-1177
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
WARNING
Due to excessive weight, care must be taken to prevent front hub and brakedrum assembly from falling Do not
pull out too far on spindle Serious injury to personnel could result.
NOTE
10 Spindle (1) Front hub (2) and a Pull front hub out enough to free outer
outer bearing (3) bearing.
b Push front hub back in.
c Take out outer bearing.
WARNING
Due to excessive weight, assistance will be needed to lift hub and brakedrum assembly. Failure to observe
this precaution could cause serious injury to personnel.
DISASSEMBLY
12 Front hub (2) Grease seal (5) a Using 3/8-inch flat-tip screwdriver, pry
out.
b Get rid of.
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only
in a well-ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use
near open flame or excessive heat The flashpoint for type #1 drycleaning solvent is 1000F (380C) and for
type #2 is 138°F (590C) If you become dizzy while using cleaning solvent, get fresh air immediately, and get
medical aid If contact with eyes is made, flush your eyes with water and get medical aid immediately.
2-1178
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to clean parts, go to General Maintenance Instructions, (page 2-424).
14 Front hub (2) and a Clean outside, inside, and bearing cups
brakedrum (4) using drycleaning solvent and cleaning
brush.
b Wipe clean using wiping rag.
15 Outer bearing (3) a Clean using drycleaning solvent and
and inner cleaning brush.
bearing (6) b Wipe clean using wiping rag.
TA2444378
2-1179
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions, (page 2-424).
18 Front hub (6) Inner bearing cup a Look for cracks, pits, scores, or
(7) and outer blueing.
bearing cup (8) Replace if damaged, steps 26 thru 29.
b Check for looseness in front hub.
If loose, replace front hub, steps 22
thru 25.
19 Front hub (6) and a Look for cracks across face or near
brakedrum (9) bearing cups (7 and 8).
b Look for stripped, bent, or broken hub
studs (10).
Replace if damaged, steps 22 thru 25.
c Look for damaged grease capscrew
holes (11).
d Look for cracks, heat spots, pitting deep
grooves, or out-of-round in brakedrum.
Replace if damaged, steps 22 thru 25.
If minor grooves or pitting is
found, notify higher category of
maintenance.
2-1180
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Due to excessive weight, assistance will be needed to lift hub and breakdrum assembly. Failure to
observe this precaution could cause serious injury to personnel.
NOTE
TA244439
2-1181
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
Safety goggles must be worn to prevent eye injury from flying metal chips when using compressed air, or
striking metal surfaces.
23 Front hub (2) Hub stud (3) Using 3-pound cross-peen hammer, drive
out.
NOTE
25 Brakedrum (1) Hub stud (3) a Put into hub stud hole.
b Drive in using 3-pound cross-peen
hammer and brass driftpin punch.
Make sure hub stud is flush against
brakedrum
TA244440
2-1182
TM 5-3805-25420-2
ACTION
LOCATION ITEM REMARKS
26 Front hub (2) Inner bearing a Position rear hub on wood blocks.
cup (4) b Using puller, pull out.
c Get rid of.
TA244441
2-1183
TM 53805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
30 Front hub (1) Inner bearing (2) Soak inner bearing and coat inner bearing
and inner bearing cup with lubricating oil
cup (3) (LO 5-3805-254-12).
32 Front hub (1) New grease seal (4) a Position level and square.
b Tap in until flush with top of front hub us-
ing wood block and 3-pound cross-peen
hammer.
Make sure grease seal Is level.
INSTALLATION
WARNING
Due to excessive weight, assistance will be needed to lift hub and breakdrum assembly. Failure to observe
this precaution could cause serious injury to personnel
TA244442
2-1184
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
Steps given are typical for right and left front hubs.
33 Spindle (5) Front hub (1) and a Coat spindle with lubricating oil.
brakedrum (6) b With assistance, put on.
Make sure inner bearing is seated on
inner race (7) on spindle.
34 Outer bearing (8) a Soak outer bearing and coat outer bear-
ing cup (9) and inner race (7) on
spindle with lubricating oil
(LO 5-3805-254-12).
b Put on.
35 Washer (10) and a Put on washer.
adjusting nut (11) b Screw on adjusting nut until snug.
TA244443
2-1185
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
36 Spindle (1) Front hub (2) Push onto spindle as far as possible.
38 Spindle (1) New cotter pin (4) Put in and bend back ends using 8-inch
roundnose pliers.
40 Grease cap (6) Three screws (7) Screw in and tighten using 7/16-inch box-
and three new end wrench.
lockwashers (8)
If brakes were taken out of adjustment or need to be adjusted, perform steps 43, 44, and 45.
2-1186
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
43 Dust shield (10) Cover (11) Using 3/8-inch flat-tip screwdriver, pry
out.
44 Brake adjuster (12) While slowly turning front hub, adjust each
brake adjuster, until a slight drag is felt,
using brake adjusting tool.
TA244444
NOTE
FOLLOW-ON MAINTENANCE: Install front wheels (page 2-1168).
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps given are typical for right and left front rear and rear rear hubs.
2-1188
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
1 Air brake Cover (2) Using 26-inch pinch bar, pry off.
chamber (1) Cover will hang from air chamber.
Safety goggles must be worn to prevent eye injury from flying metal chips when using compressed air, or
striking metal surfaces.
Stand to side of axle flange while striking to prevent injury from flying lock collars.
CAUTION
4 Axle flange (4) Eight lock a Place 1-gallon drain pan underneath.
collars (6) b Using 12-pound cross-peen hammer,
strike sharply on edge of axle flange to
loosen.
c Take out lock collars.
d Get rid of drained oil (page 2-424).
TA244445
2-1189
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
5 Rear hub (1) Axle (2) and axle a Pull out axle.
flange gasket (3) b Take off gasket.
c Get rid of gasket.
7 Spindle (6) Locknut (7) Using 4-inch, 3/4-inch drive socket and
hinged handle, unscrew and take off.
Due to excessive weight, care must be taken to prevent rear hub and brakedrum assembly from falling Do
not pull out too far on spindle Serious injury to personnel could result.
NOTE
10 Rear hub (1) and a Pull rear hub out enough to free outer
outer bearing (10) bearing.
b Push rear hub back in.
c Take off outer bearing.
WARNING
Due to excessive weight, assistance will be needed to lift hub and brakedrum assembly. Failure to observe
this precaution could cause serious injury to personnel.
2-1190
TM 5-3805-254.20-2
ACTION
LOCATION ITEM REMARKS
11 Spindle (6) Rear hub (1) and With two assistants, take off.
brakedrum (11)
DISASSEMBLY
12 Rear hub (1) Inner seal (12) a Using 26-inch pinch bar, pry out.
b Get rid of.
TA244446
2-1191
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do not
use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F (380C) and
for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air immediately, and
get medical aid. If contact with eyes is made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
14 Rear hub (1) and a Clean outside, inside, and bearing cups
brakedrum (2) using drycleaning solvent and cleaning
brush.
b Wipe clean using wiping rag.
INSPECTION/REPLACEMENT
NOTE
2-1192
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
18 Rear hub (1) Inner bearing cup a Look for cracks, pits, scores, or
(9) and outer bearing blueing.
cup (10) Replace If damaged, steps 27 thru 30.
b Check for looseness in rear hub.
If loose, replace rear hub, steps 23
thru 26
TA244447
2-1193
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
19 Rear hub (1) and a Look for cracks across face or near
brakedrum (2) bearing cups (3 and 4).
b Look for stripped, bent, or broken hub
studs (5).
Replace if damaged, steps 23 thru 26.
c Look for stripped, bent, or broken axle
flange studs (6).
If damaged, notify higher category of
maintenance.
d Look for cracks, heat spots, pitting,
deep grooves, or out-of-round in
brakedrum.
Replace if damaged, steps 23 thru 26.
If minor grooves or pitting is found,
notify higher category of
maintenance.
TA244448
2-1194
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Due to excessive weight, assistance will be needed to lift hub and breakdrum
assembly. Failure to observe this precaution could cause serious injury to
personnel.
NOTE
Safety goggles must be worn to prevent eye injury from flying metal chips.
24 Rear hub (1) Hub stud (5) Using 3-pound cross-peen hammer, drive
out.
NOTE
TA244449
2-1195
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
25 Rear hub (1) and a Position rear hub on wood blocks with
brakedrum (2) axle flange studs (3) facing down.
b Position brakedrum on rear hub facing
up.
c Aline hub stud holes.
26 Brakedrum (2) Hub stud (4) a Put into hub stud hole.
b Drive in using 3-pound cross-peen
hammer and brass driftpin punch.
Make sure hub stud is flush against
brakedrum.
27 Rear hub (1) Inner bearing a Position rear hub on wood blocks with
cup (5) axle flange studs (3) facing down.
b Using puller, pull out.
c Get rid of.
TA244450
2-1196
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244451
2-1197
TM 5-3805-25420-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
31 Rear hub (1) Inner bearing (2) Pack inner bearing and coat inner bearing
and inner bearing cup with grease (LO 5-3805-254-12).
cup (3)
33 Rear hub (1) New inner seal (4) a Position level and square.
b Tap in until flush with top of rear hub
using wood block and 1-pound ball-peen
hammer.
Make sure inner grease seal Is level.
WARNING
Due to excessive weight, assistance will be needed to lift hub and brake drum assembly. Failure to observe
this precaution could cause serious injury to personnel.
TA244452
2-1198
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
Steps given are typical for right and left front rear and rear rear hubs.
34 Spindle (5) Rear hub (1) and a Coat spindle with grease
brakedrum (6) (LO 5-3805-254-12).
b With assistance, put on.
Make sure inner bearing is seated on
inner race (7) on spindle.
36 Adjusting nut (10) a Position with pin (11) facing out and
screw on and tighten until snug.
b While slowly turning rear hub (1),
torque to 50 ft lb (70 N.m) using 4-inch,
3/4-inch drive socket and 0 to 600 ft lb
(0 to 814 N.m) torque wrench.
c Loosen one-quarter turn using 4-inch,
3/4-inch drive socket and hinged
handle
TA244453
2-1199
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
37 Spindle (1) Adjusting nut Put on and aline hole in adjusting nut lock
lock (2) with pin (3) on adjusting nut (4).
If hole and pin do not aline, tighten
adjusting nut to nearest hole and push
adjusting nut lock into place.
39 Rear hub (6) New outer seal Put in position on axle flange studs (9).
gasket (7) and new
outer seal (8)
41 Spindle (1) Axle (11) a Push in and aline axle flange (12) holes
with axle flange studs (9) on rear
hub (6).
b Push into position.
43 Air brake Caging bolt (16) Tighten fully using 3/4-inch, 1/2-inch drive
chamber (15) deep socket and ratchet handle.
2-1200
TM 5-3805-254-20-2
NOTE
FOLLOW ON MAINTENANCE:
TA244454
Change 1 2-1201
TM 5-3805-254-20-2
Page Page
Draining Steering System .................................... 2-1207 Pump Bypass Hose and Fittings ......................... 2-1232
Filling Steering System ........................................ 2-1243 Pump-to-Left Steering Gear
Filter ..................................................................... 2-1202 Hose and Fittings ................................................ 2-1228
Left Steering Gear-to-Reservoir Reservoir-to-Pump Hose and
Hose and Fittings ................................................. 2-1212 Fittings ................................................................. 2-1224
Left Steering Gear-to-Right Steering Right Steering Gear-to-Left
Gear Hose and Fittings ....................................... 2-1215 Steering Gear Hose and
Oil Reservoir ........................................................ 2-1237 Fittings.................................................................. 2-1220
FILTER
This task covers:
INITIAL SETUP
2-1202
TM 5-3805-254-20-2
FILTER - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA244455
2-1203
TM 5-3805-254-20-2
FILTER - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only
in a well-ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use near
open flame or excessive heat The flashpoint for type #1 drycleaning solvent is 1000F (380C) and for type #2 is
138°F (590C) If you become dizzy while using cleaning solvent, get fresh air immediately, and get medical aid
If contact with eyes is made, flush your eyes with water and get medical aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user
and other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa) User must wear safety goggles or face shield to prevent injury to personnel.
9 All parts Using air blow gun and air hose assembly,
blow dry.
2-1204
TM 5-3805-254-20-2
FILTER - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
TA244456
2-1205
TM 5-3805-254-20-2
FILTER - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
16 Reservoir (2) Drainplug (1) Screw in and tighten using 7/16-inch open-
end wrench.
Start engine (TM 5-3805-254-10) and allow engine to idle Turn wheels to full left and full right three times Shut
down engine (TM 5-3805-254-10).
2-1206
TM 5-3805-254-20-2
FILTER - CONTINUED
NOTE
FOLLOW-ON MAINTENANCE:
Draining (2-1207)
INITIAL SETUP
Tools Materials/Parts
Equipment Condition
TA244457
2-1207
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Do not drain steering system when hot Hot oil can burn you.
2-1208
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244458
2-1209
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9 Elbow (1) Hose (2) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
10 Elbow (3) Hose (4) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from
seizing.
NOTE
For more information on how to use antiseizing tape go to General Maintenance Instructions (page 2-424).
12 Left frame Clamp (8), screw Screw in and tighten using two 7/16-inch
rail (7) (9), new lockwasher open-end wrenches.
(10), and nut (11)
13 Elbow (12) Hose (4) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
14 Elbow (13) Hose (2) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
2-1210
TM 5-3805-254-20-2
CAUTION
NOTE
FOLLOW-ON MAINTENANCE:
TA244459
2-1211
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
2-1212
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa) User
must wear safety goggles or face shield to prevent injury to personnel.
6 All parts Using air blow gun and air hose assembly,
blow dry.
TA244460
2-1213
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
INSTALLATION
10 Left steering Elbow (1) Wrap pipe threads with antiseizing tape
gear (4) (page 2-424).
12 Elbow (1) Hose (3) Screw on and tighten using 3/4-inch and 1-
inch open-end wrenches.
13 Reservoir (6) Elbow (2) Wrap pipe threads with antiseizing tape
(page 2-424).
15 Elbow (2) Hose (3) Screw on and tighten using 3/4-inch and 1-
inch open-end wrench.
2-1214
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Tools Materials/Parts
TA244461
2-1215
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
4 Four clamps (5) Four screws (6), a Using two 7/16-inch box-end wrenches,
four nuts (7), and unscrew and take out.
four lockwashers (8) b Get rid of lockwashers.
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
2-1216
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa)
User must wear safety goggles or face shield to prevent injury to personnel.
9 All parts Using air blow gun and air hose assembly,
blow dry.
TA244462
2-1217
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
INSTALLATION
13 Right steering Elbow (3) a Wrap pipe threads with antiseizing tape
gear (5) (page 2-424).
b Screw in and tighten using 11/16-inch
open-end wrench.
14 Elbow (3) Hose (4) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
2-1218
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
19 Elbow (1) Hose (4) Screw on and tighten using 11/16-inch and
7/8-inch open-end wrenches.
NOTE
FOLLOW-ON MAINTENANCE: Close right side hood panel (page 2-424).
TASK ENDS HERE
TA244463
2-1219
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
3 Four clamps (4) Four screws (5), a Using two 7/16-inch box-end wrenches,
four nuts (6), and unscrew and take out.
four lockwashers (7) b Get rid of lockwashers.
2-1220
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
TA244464
2-1221
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa) User
must wear safety goggles or face shield to prevent injury to personnel.
9 Elbow (1), hose (2), Using air blow gun and air hose assembly,
elbow (3), and blow dry.
adapter (4)
INSPECTION/REPLACEMENT
NOTE
INSTALLATION
13 Left steering Adapter (4) a Wrap pipe threads with antiseizing tape
gear (5) (page 2-424).
b Screw in and tighten using 3/4-inch
open-end wrench.
14 Adapter (4) Elbow (1) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 11/16-inch
and 3/4-inch open-end wrenches.
15 Elbow (1) Hose (2) Screw on and tighten using 11/16-inch and
718-inch open-end wrenches.
2-1222
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
18 Right steering Elbow (3) a Wrap pipe threads with antiseizing tape
gear (10) (page 2-424).
b Screw in and tighten using 11/16-inch
open-end wrench.
19 Elbow (3) Hose (2) Screw on and tighten using 11116-inch and
718-inch open-end wrenches.
2-1223
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
2-1224
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
TA244466
2-1225
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa) User
must wear safety goggles or face shield to prevent injury to personnel.
6 Elbow (1) and Using air blow gun and air hose assembly,
hose (2) blow dry.
INSPECTIONIREPLACEMENT
NOTE
INSTALLATION
10 Elbow (3) Hose (2) Screw on and tighten using two 1 1/2-inch
open-end wrenches.
11 Reservoir (4) Elbow (1) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 5/16-inch
open-end wrench.
12 Elbow (1) Hose (2) Screw on and tighten using 1 1/2-inch and
1 5/16-inch open-end wrenches.
13 Reservoir (4) Drainplug (5) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 7/16-inch
open-end wrench.
2-1226
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
FOLLOW-ON MAINTENANCE: Close left side hood panel (page 2-424) 2-1227
2-1227
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
5 Pump (7) Elbow (6) and a Using 7/8-inch open-end wrench, un-
Ring (8) screw and take out.
b Get rid of ring.
2-1228
TM 5-3805-254-20-2
PUMP-TO-LEFT STEERING GEAR HOSE AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
TA244468
2-1229
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa)
User must wear safety goggles or face shield to prevent injury to personnel.
7 Elbow (1), hose (2), Using air blow gun and air hose assembly,
elbow (3), and blow dry.
drainplug (4)
INSPECTION/REPLACEMENT
NOTE
INSTALLATION
12 Pump (6) Elbow (1) and new Screw on and tighten using two 718-inch
ring (5) open-end wrenches.
13 Elbow (1) Hose (2) Screw on and tighten using two 7/8-inch
open-end wrenches.
14 Left steering Elbow (3) a Wrap pipe threads with antiseizing tape
gear (7) (page 2-424).
b Screw in and tighten using 13/16-inch
open-end wrench.
2-1230
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
15 Elbow (3) Hose (2) Screw on and tighten using 13116-inch and
7/8-inch open-end wrenches.
16 Reservoir (8) Drainplug (4) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 7/16-inch
open-end wrench.
NOTE
FOLLOW-ON MAINTENANCE: Close left side hood panel (page 2-424).
TASK ENDS HERE
TA244469
2-1231
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
2-1232
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244470
2-1233
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable Wear protective safety goggles and gloves and use only
in a well-ventilated area Avoid contact with skin, eyes, and clothes and do not breathe vapors Do not use
near open flame or excessive heat The flashpoint for type #1 drycleaning solvent is 1000F (380C) and for
type #2 is 138°F (590C) If you become dizzy while using cleaning solvent, get fresh air immediately, and get
medical aid If contact with eyes is made, flush your eyes with water and get medical aid immediately.
Improper cleaning methods and use of unauthorized cleaning liquids or solvent can injure personnel Refer to
TM 9-247.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa)
User must wear safety goggles or face shield to prevent injury to personnel.
10 All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
Change 1 2-1234
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
14 Pump (6) Elbow (2) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1-inch open-
end wrench.
15 Elbow (2) Elbow (3) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 13116-inch
and 1-inch open-end wrenches.
16 Elbow (3) Hose (1) Screw on and tighten using 1-inch and
13/16-inch open-end wrenches.
17 Pump (6) Elbow (4) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 1/2-inch
open-end wrench.
TA244471
2-1235
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
18 Elbow (1) Hose (2) Screw on and tighten using two 1 1/2-inch
open-end wrenches.
20 Elbow (3) Hose (4) Screw on and tighten using 3/4-inch and 1-
inch open-end wrenches.
21 Reservoir (5) Drainplug (6) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 7/16-inch
open-end wrench.
TA244472
2-1236
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
OIL RESERVOIR
INITIAL SETUP
Tools Materials/Parts
Change 1 2-1237
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not drain oil reservoir when hot. Hot oil can burn you.
6. Bracket (7) Four screws (8) a. Using 9/16-inch open-end wrench, un-
and four screw and take out.
lockwashers (9) b. Get rid of lockwashers.
TA244473
2-1238
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
7.1. Support (10) Four screws (11) Using two 3/4-inch open-end wrenches,
and nuts (12) unscrew, and take out.
7.2. Engine mount Two screws (14) and Using two 3/4-inch open-end wrenches,
bracket (13) nuts (15) unscrew, and take out.
7.4. Two screws (16) and Using two 3/4-inch open-end wrenches,
nuts (17) unscrew, and take out.
TA702177
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
NOTE
8. Strap (10) Two screws (11), two a. Using two 1/2-inch open-end
lockwashers (12), and wrenches, unscrew and take out.
two nuts (13) b. Get rid of lockwashers.
TA244474
2-1239
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and
gloves and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes
and do not breathe vapors. Do not use near open flame or excessive heat. The
flashpoint for type #1 drycleaning solvent is 100°F (38°C) and for type #2 is 138°F (59°C).
If you become dizzy while using cleaning solvent, get fresh air immediately, and get
medical aid. If contact with eyes is made, flush your eyes with water and get medical aid
immediately.
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can
injure personnel and cause damage to equipment. Refer to TM 9-247.
NOTE
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed
away from user and other personnel in the area. Compressed air used for cleaning
purposes shall not exceed 30 psi (207 kPa). User must wear safety goggles or face
shield to prevent injury to personnel.
11. All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
2-1240
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
19. Two screws (6), two Screw in and tighten using two 1/2-inch
new lockwashers (7), open-end wrenches.
and two nuts (8)
TA702178
Change 1 2-1241
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
21. Two screws (3) and Screw in and tighten using two 3/4-inch
nuts (4) open-end wrenches.
21.2. Two screws (6) and Screw in and tighten using two 3/4-inch
nuts (7) open-end wrenches.
21.3. Support (2) Four screws (8) and Screw in and tighten using two 3/4-inch
nuts (9) open-end wrenches.
21.5. Four screws (11) and Screw in and tighten using 9/16-inch open-end
four new lockwashers wrench.
(12)
Change 1 2-1241.0
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702179
Change 1 2-1241.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
22. Reservoir (1) Elbow (2) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 1 5/16-inch
open-end wrench.
23. Elbow (2) Hose (3) Screw on and tighten using 1 5/16-inch and
1 1/2-inch open-end wrenches.
24. Reservoir (1) Elbow (4) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 3/4-inch
open-end wrench.
25. Elbow (4) Hose (5) Screw on and tighten using 3/4-inch and 1-
inch open-end wrenches.
NOTE
2-1242
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
TA244477
2-1243
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
2. Reservoir (1) Filler neck (2) Fill with lubricating oil to 4 inches (10.16
cm) below top of filler neck using 6-inch
machinist scale.
CAUTION
Failure to perform the following steps could cause serious damage to equipment.
5. Steering wheel (6) Slowly turn to full left and to full right three
times.
10. Steering wheel (6) Slowly turn to full left and to full right
for three minutes.
NOTE
Steps 13, 14, and 15 are typical for both left and right steering arms.
2-1244
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13. Left steering arm Cotter pin (9) a. Using 8-inch roundnose pliers,
(7) and link end (8) straighten ends and take out.
b. Get rid of.
15. Left steering Link end (8) Using 8-inch mechanical puller, screw in
arm (7) and take out.
16. Right steering Link end (12) Repeat steps 13, 14, and 15.
arm (11)
TA244478
2-1245
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
FILLING - CONTINUED
WARNING
Stand clear of steering arms while performing step 18. Failure to observe this precaution
could cause serious injury to personnel.
CAUTION
Do not move steering arms by hand. Air could be pulled back into system.
NOTE
Steps 18 thru 22 are typical for both left and right steering arms.
18. Steering wheel (3) a. Have assistant turn steering wheel to full
left and hold until right steering arm
moves to stop.
b. Turn to full right and hold until right
steering arm moves to stop.
c. Repeat a and b three times.
d. Turn to aline left steering arm with link
end.
21. Link end (5) Nut (6) Screw on and tighten using 1 5/16-inch
open-end wrench.
Aline hole in link end with slot In nut.
22. Link end (5) New cotter pin (7) Put in and bend ends back using 8-inch
and nut (6) roundnose pliers (page 2-424).
24. Dump truck (1) Steering wheel (3) Repeat step 18.
and right steering
arm (8)
2-1246
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
26. Right steering Link end (9), nut Repeat steps 20, 21, and 22.
arm (8) (10), and new cotter
pin (11)
NOTE
FOLLOW-ON MAINTENANCE:
2-1247
TM 5-3805-254-20-2
Page
PINTLE HOOK
INITIAL SETUP
Tools Personnel
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Due to excessive weight, assistance will be needed to lift and remove pintle hook
assembly from rear chassis cross-member. Serious injury to personnel could result.
Safety goggles must be worn when working under truck to prevent eye injury.
1. Rear chassis Four screws (2), a. Using 1/2-inch drive 6-inch extension,
cross-member (1) four nuts (3), and ratchet handle, 1 1/8-inch socket and
four lockwashers (4) 1 1/8-inch box-end wrench, with
assistance, unscrew and take off.
b. Get rid of lockwashers.
2-1248
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
WARNING
Due to excessive weight, assistance will be needed to lift and remove pintle hook
assembly from rear chassis cross-member. Serious injury to personnel could result.
Safety goggles must be worn when working under truck to prevent injury.
NOTE
2-1249(2-1250 blank)
TM 5-3805-254-20-2
Page Page
HOOD
INITIAL SETUP
Handle, ratchet, 1/2-inch drive Nut, self-locking, center hood rod retainer
Pliers, slip-joint, 8-inch to cowl (two required)
Screwdriver, cross-tip, number two Nut, self-locking, center hood rod retainer
Screwdriver, cross-tip, number three to fire wall bracket (two required)
Socket, 7/16-inch, 1/2-inch drive Nut, self-locking, hood rest to hood (two
Socket, 1/2-inch, 1/2-inch drive required)
Wrench, box-end, 7/16-inch
Wrench, box-end, 1/2-inch Personnel Required
Wrench, open-end, 7/16-inch
Wrench, open-end, 1/2-inch Three
Cotter pin, anchor pin (four required) Left and right side hood panels opened
Lockwasher, hood handle (four required) (page 2-424).
Change 1 2-1251
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Assistance is needed to support hood panel to prevent falling and causing personal injury.
1. Right hood rest (1) Screw (2) and self- a. Using 1/2-inch drive, 7/16-inch
locking nut (3) socket, ratchet handle, and 7/16-inch
box-end wrench, unscrew and take off.
b. Get rid of self-locking nut.
c. Place right side hood panel on top of left
hood panel.
2. Center hood rod Two screws (5) and a. Using number three cross-tip screw-
retainer (4) two self-locking driver and 1/2-inch open-end wrench,
nuts (6) unscrew and take off.
b. Get rid of self-locking nuts.
c. With two assistants, close right side
hood panel.
3. Left hood rest (7) Screw (8) and self- a. Using 1/2-inch drive, 7/16-inch
locking nut (9) socket, ratchet handle, and 7/16-inch
box-end wrench, unscrew and take off.
b. Get rid of self-locking nut.
c. Place left side hood panel on top of right
side hood panel.
4. Center hood rod Two screws (10) and a. Using number three cross-tip screw-
retainer (4) two self-locking driver and 1/2-inch open-end wrench,
nuts (11) unscrew and take off.
b. Get rid of self-locking nuts.
c. With two assistants, close left side hood
panel.
2-1252
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
WARNING
Due to excessive weight, assistance is needed to prevent personal injury when lifting
heavy parts.
5. Cowl (12) and Hood assembly (14) With two assistants, take off.
radiator shell (13)
TA244481
2-1253
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
7. Right side hood Hood handle (2), a. Using number three cross-tip screw-
panel (1) two screws (3), and driver, unscrew and take out.
two lockwashers (4) b. Get rid of lockwashers.
8. Hood rest (5) Shoulder bolt (6) Using 1/2-inch drive, 1/2-inch socket,
and nut (7) ratchet handle, and 1/2-inch box-end
wrench, unscrew and take out.
9. Hood brackets (8) Two screws (9) and Using number two cross-tip screwdriver and
two nuts (10) 1/2-inch box-end wrench, unscrew and
take off.
TA702180
Change 1 2-1254
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
11. Left side hood Hood handle (16), a. Using number three cross-tip screw-
panel (15) two screws (17), and driver, unscrew and take out.
two lockwashers (18) b. Get rid of lockwashers.
12. Hood rest (19) Shoulder bolt (20) Using 1/2-inch drive, 1/2-inch socket,
and nut (21) ratchet handle, and 1/2-inch box-end
wrench, unscrew and take out.
13. Hood brackets (22) Two screws (23) and Using number two cross-tip screwdriver and
two nuts (24) 1/2-inch box-end wrench, unscrew and
take off.
14. Air intake deflector Four bolts (27) Using 7/16-inch open-end wrench, un-
(25) and intake and four flat screw and take out.
cover plate (26) washers (28)
TA244483
2-1255
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
15. Hood latch hooks (1) Look for cracks, brittleness, and broken
pieces.
16. Anchor pins (2) Look for cracks, breaks, and wear.
TA244484
2-1256
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
18. Hood panels (4) Check welded and riveted areas for cracks
or breaks.
TA244485
2-1257
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
22. Right side hood Hood handle (2), two Screw in and tighten using number three
panel (1) screws (3), and two cross-tip screwdriver.
new lockwashers (4)
23. Hood rest (5) Shoulder bolt (6) Screw in and tighten using 1/2-inch drive,
and nut (7) 1/2-inch socket, ratchet handle, and
1/2-inch box-end wrench.
24. Hood brackets (8) Two screws (9) and Screw in and tighten using number two
two nuts (10) cross-tip screwdriver and 1/2-inch box-end
wrench.
Change 1 2-1258
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
26. Left side hood Hood handle (16), Screw in and tighten using number three
panel (15) two screws (17), cross-tip screwdriver.
and two new
lockwashers (18)
27. Hood rest (19) Shoulder bolt (20) Screw in and tighten using 1/2-inch drive,
and nut (21) 1/2-inch socket, ratchet handle, and
1/2-inch box-end wrench.
28. Hood brackets (22) Two screws (23) and Screw in and tighten using number two
two nuts (24) cross-tip screwdriver and 1/2-inch box-end
wrench.
29. Air intake deflector Four bolts (27) Screw in and tighten using 7/16-inch open-
(25) and intake and four flat end wrench.
cover plate (26) washers (28)
TA244487
2-1259
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
WARNING
Due to excessive weight, assistance is needed to prevent personal injury when lifting
heavy parts.
31. Cowl and radiator Hood assembly (4) With two assistants, place in position and
shell (3) aline boltholes.
WARNING
Assistance is needed to support hood panel to prevent falling and causing personal injury.
32. Left side center Two screws (5) a. Place left side hood panel on top of right
hood rod and two new self- side hood panel.
retainer (2) locking nuts (6) b. Screw in and tighten using number three
cross-tip screwdriver and 1/2-inch
open-end wrench.
33. Hood rest (7) Screw (8) and new a. With two assistants, support hood in
self-locking nut (9) open position.
b. Screw in and tighten using 1/2-inch
drive, 7/16-inch socket, ratchet
handle, and 7/16-inch box-end
wrench.
c. With two assistants, close left side hood
panel.
34. Right side center Two screws (11) and a. Place right side hood panel on top of left
hood rod two new self-locking side hood panel.
retainer (10) nuts (12) b. Screw in and tighten using number three
cross-tip screwdriver and 1/2-inch
open-end wrench.
2-1260
TM 5-3805-254-20-2
HOOD - CONTINUED
ACTION
LOCATION ITEM REMARKS
35. Hood rest (13) Screw (14) and new a. With two assistants, support hood in
self-locking nut (15) open position.
b. Screw in and tighten using 1/2-inch
drive, 7/16-inch socket, ratchet
handle, and 7/16-inch box-end
wrench.
c. With two assistants, close right side
hood panel.
NOTE
FOLLOW-ON MAINTENANCE: Close left and right side hood panels (page 2-424).
TA244488
PASSENGER SEAT
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Seat frame (1) Seat cushion (2) Lift up and take off.
2. Seat frame (1) to Four screws (4), a. Using 1/2-inch drive, 9/16 inch socket
heater box (3) four lockwashers and ratchet handle, unscrew and take
(5), and four flat out.
washers (6) b. Get rid of lockwashers.
4. Seat frame (1) Back cushion (7) and a. Using number two cross-tip screw-
four screws (8) driver, unscrew and take out.
b. Take off back cushion.
INSPECTION/REPLACEMENT
NOTE
2-1272
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
7. Seat cushion support Staples (10), seat a. Using 1/4-inch flat-tip screwdriver,
(9) cushion (2) and pry staples away from seat cushion.
cover (11) b. Get rid of staples.
c. Take cover off seat cushion.
8. Back cushion support Staples (13), back a. Using 1/4-inch flat-tip screw driver, pry
(12) cushion (7) and staples away from back cushion.
cover (14) b. Get rid of staples.
c. Take cover off back cushion.
TA244661
2-1273
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
9. Back cushion support Cover (2), and back Put cover on back cushion.
(1) cushion (3)
10. Back cushion (3) Back cushion support Using staple gun and 3/8-inch staples,
(1), cover (2) and attach cover to back cushion support.
staples (4).
11. Seat cushion support Cover (6) and seat Put cover on seat cushion.
(5) cushion (7)
12. Seat cushion (7) Seat cushion support Using staple gun and 3/4-inch staples,
(5), cover (6) and attach cover to seat cushion support.
staples (8).
INSTALLATION
13. Seat frame (9) Back cushion (3) and a. Put back cushion in place.
four screws (10) b. Screw in and tighten using number two
cross-tip screwdriver.
15. Seat frame (9) to Four screws (12), Screw in and tighten using 1/2-inch drive,
heater box (11) four new lockwashers 9/16 socket and ratchet handle.
(13) and four flat
washers (14)
16. Seat frame (9) Seat cushion (7) Put in position and push down until cushion
snaps into place.
NOTE
FOLLOW-ON MAINTENANCE: Close right cab door (page 2-424).
TASK ENDS HERE TA244497
2-1274
TM 5-3805-254-20-2
DRIVER’S SEAT
INITIAL SETUP
Airbrake system drained (page 2-1034). Lockwasher, driver’s seat (four required)
Lockwasher, seat riser (four required)
Tools/Test Equipment
Personnel Required
Handle, ratchet, 3/8-in drive
Socket, 1/2-inch, 3/8-Inch drive One
Extension, 3-inch, 3/8-inch drive
Wrench, open-end, 7/16-inch
Wrench, open-end, 9/16-inch
Change 1 2-1274.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Drain air from airbrake system before removing fittings to avoid injury to personnel from
compressed air.
1. Pipe nipple (1) Air hose (2) Using 7/16-inch and 9/16-inch open-end
wrenches, unscrew, and take off.
2. Seat riser (3) Four nuts (4) and a. Using 1/2-inch, 3/8-inch drive socket, 3-inch
lockwashers (5) extension, and ratchet handle, unscrew, and
take out.
b. Get rid of lockwashers.
4. Floorboards (7) Four screws (8), a. Using 1/2-inch, 3/8-inch drive socket, 3-inch
lockwashers (9), extension, and ratchet handle, unscrew, and
and washers (10) take out.
b. Get rid of lockwashers.
INSTALLATION
7. Four screws (8), new Screw in and tighten using 1/2-inch, 3/8-inch
lockwashers (9), and drive socket, 3-inch extension, and ratchet
washers (10) handle.
9. Four nuts (4) and Screw in and tighten, using 1/2-inch, 3/8-inch
new lockwashers (5) drive socket, 3-inch extension, and ratchet
handle.
10. Pipe nipple (1) Air hose (2) Screw on and tighten using 7/16-inch and 9/16-
inch open-end wrenches.
Change 1 2-1274.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA702182
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
NOTE
Steps given are typical for seat and back cushion covers.
REMOVAL
1. Cushion pan (1) Eight clips (2), a. Using 1/4-inch flat-tip screwdriver, pry clips
cushion (3), and away from cushion.
cover (4) b. Take cushion off cushion pan.
c. Pull cover off cushion.
TA702183
Change 1 2-1275
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
3. Driver’s seat (1) Four screws (2) Put on and tighten using 7/16-inch box-end
and cushion pan (3) wrench.
4. Cushion pan (3) Cover (4), cushion (5), a. Put cover on cushion.
and eight clips (6) b. Put cushion on cushion pan and pry clips
over cushion using 1/4-inch flat-tip
screwdriver.
NOTE
TA702184
Change 1 2-1275.0
TM 5-3805-254-20-2
SPLASH GUARDS
INITIAL SETUP
Materials/Parts
REMOVAL
NOTE
1. Mounting bracket (1) Four bolts (2), four Using 9/16-inch and 1/2-inch box-end
lockwashers (3), and wrenches, unscrew and take out.
four nuts (4)
INSTALLATION
2-1280
TM 5-3805-254-20-2
SPLASH GUARDS
ACTION
LOCATION ITEM REMARKS
4. Four bolts (2), four Screw in and tighten using 9/16-inch and
new lockwashers (3), 1/2-inch box-end wrenches.
and four nuts (4)
TA244501
2-1281
TM 5-3805-254-20-2
SEAT BELTS
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Right side rear Two bolts (2) and a. Using 3/4-inch box-end wrench, un-
cab wall (1) seat belts (3) screw bolts and take out.
b. Take off seat belts.
2. Driver’s seat (4) Two bolts (5), two a. Using 1/2-inch drive 5/16-inch socket,
nuts (6), and seat ratchet handle, and 11/16-inch open-
belts (7) end wrench, unscrew bolts and nuts and
take out.
b. Take off seat belts.
INSTALLATION
WARNING
3. Drivers seat (4) Two bolts (5), two a. Put seat belts in place.
nuts (6), and seat b. Position seat belt at 45-degree angle.
belts (7) c. Screw in and tighten bolts and nuts using
1/2-inch drive 15/16-inch socket,
ratchet handle, and 11/16-inch open-
end wrench.
2-1282
TM 5-3805-254-20-2
TA244502
2-1283
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Right side rear Two bolts (2) and a. Put seat belts in place.
cab wall (1) seat belts (3) b. Position seat belt at 45-degree angle on
right side rear cab wall.
c. Screw in and tighten bolts using
3/4-inch box-end wrench.
NOTE
2-1284
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Top of body (1) Four nuts (2), Using 9/16-inch, 1/2-inch drive deep socket,
washers (3), and ratchet handle, and 9/16-inch box-end wrench,
screws (4) unscrew, and take off.
TA702185
Change 1 2-1284.1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSTALLATION
5. Top of body (3) Tool rack (1) With assistance, put on.
TA702186
Change 1 2-1284.2
TM 5-3805-254-20-2
RADIATOR GRILLE
INITIAL SETUP
Personnel Required
One
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Radiator shell (1) Seven screws (2) Using 1/2-inch, 3/8-inch drive socket and 3/8-
and radiator grille inch drive ratchet handle, unscrew and take off.
(3)
TA702187
Change 1 2-1284.3
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSTALLATION
3. Radiator shell (2) Seven speed nuts (1) Put into position on radiator shell.
Change 1 2-1284.4
TM 5-3805-254-20-2
Page Page
INITIAL SETUP
Change 1 2-1290
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Except as noted, the steps in this task are the same for both right and left rearview mirror
assemblies. The left rearview mirror assembly is used as the example.
1. Mirror head (1) Nut (3) and a. Using 1/2-inch box-end wrench, hold-
to upper mirror lockwasher (4) ing mirror head, unscrew and take off.
clamp (2) b. Get rid of lockwasher.
2. Mirror head (1) Nut (6) and a. Using 1/2-inch box-end wrench, hold-
to lower mirror lockwasher (7) ing mirror head, unscrew and take off.
clamp (5) b. Get rid of lockwasher.
TA244509
2-1291
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
4. Rearview mirror arm Dome nut cap (4) Unscrew and take off by hand.
(1) to support bar
(2) and upper mirror
mounting bracket (3)
7. Rearview mirror Dome nut cap (11) Unscrew and take off by hand.
arm (1) to lower
mirror mounting
bracket (10)
11. Support bar (2) to Dome nut cap (18) Unscrew and take off by hand.
lower mirror mount-
ing bracket (10)
2-1292
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
14. Weld screw (20) Nut (21), lockwasher a. Using 7/16-inch, 3/8-inch drive deep-
(22), and flat well socket and ratchet handle, unscrew
washer (23) and take off.
b. Get rid of lockwasher.
15. Upper mirror mount- Two screws (25) Using number two cross-tip screwdriver,
ing bracket (3) to unscrew and take out.
door (24)
17. Lower mirror mount- Two screws (25) Using number two cross-tip screwdriver,
ing bracket (10) to unscrew and take out.
door (24)
TA244510
2-1293
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
20. Lower mirror mount- Two screws (3) Screw in and tighten using number two
ing bracket (2) to cross-tip screwdriver.
door (1)
22. Upper mirror mount- Two screws (5) Screw in and tighten using number two
ing bracket (4) to cross-tip screwdriver.
door (1)
23. Weld screw (6) Flat washer (7), new Screw on and tighten using 7/16-inch, 3/8-
lockwasher (8), and inch drive deep-well socket and ratchet
nut (9) handle.
25. Support bar (10) to Nut (11) Screw on and tighten using 7/16-inch, 3/8-
lower mirror mount- inch drive deep-well socket and ratchet
ing bracket (2) handle.
29. Rearview mirror Bolt (15), new lock- Screw in and tighten using 7/16-inch, 3/8-
arm (13) to lower washer (16), flat inch drive deep-well socket and ratchet
mirror mounting washer (17), nut handle.
bracket (2) (18), and mirror
index spring (19)
2-1294
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
30. Rearview mirror Dome nut cap (20) Screw on and tighten.
arm (13) to lower
mirror mounting
bracket (2)
32. Rearview mirror arm Bolt (22), new lock- Screw in and tighten using 7/16-inch, 3/8-
(13) to support bar washer (23), flat inch drive deep-well socket and ratchet
(10) and upper washer (24), and handle.
mirror mounting nut (25)
bracket (4)
TA244511
2-1295
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
34. Upper mirror clamp Mirror head (3) Place in position and hold.
(1) to lower mirror
clamp (2)
35. Mirror head (3) Nut (4) and new Screw on and tighten using 1/2-inch box-
to lower mirror lockwasher (5) end wrench.
clamp (2)
36. Mirror head (3) Nut (6) and new Screw on and tighten using 1/2-inch box-
to upper mirror lockwasher (7) end wrench.
clamp (1)
ADJUSTMENT
NOTE
Steps given are typical for adjusting right and left rear view mirrors.
37. Rearview mirror Two dome nut caps Unscrew and take off by hand.
arm (8) to mirror (11 and 12)
mounting brackets
(9 and 10)
TA244512
2-1296
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
38. Two nuts (13) and Loosen using two 7/16-inch box-end
two screws (14) wrenches.
39. Mirror head (3) Two nuts (4 and 6) Loosen using 1/2-inch box-end wrench.
to mirror clamps
(1 and 2)
TA244513
2-1297
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ADJUSTMENT - CONTINUED
41. Rearview mirror Two nuts (4) and Tighten using 7/16-inch box-end wrench.
arm (1) to mirror two screws (5)
mounting brackets
(2 and 3)
43. Mirror head (7) Two nuts (10) Tighten using 1/2-inch box-end wrench.
to mirror clamps
(8 and 9)
TA244514
2-1298
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
INSPECTION
NOTE
The steps in this task are typical for both left and right windshield wiper blades.
1. Wiper arm (1) Wiper blade (2) a. Inspect for cracked, chipped, torn, or
and support (3) worn rubber.
b. Inspect support for cracks or broken
springs.
TA244515
2-1299
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
2. Wiper arm (1) to Screw (3) and Using 1/4-inch, 1/4-inch drive socket and
wiper blade (2) nut (4) ratchet handle and 1/8-inch flat-tip screw-
driver, unscrew and take off.
INSTALLATION
5. Wiper arm (1) to Screw (3) and Screw in and tighten using 1/4-inch, 1/4-
wiper blade (2) nut (4) inch drive socket and ratchet handle and
1/8-inch flat-tip screwdriver.
TA244516
2-1300
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
The steps in this task are typical for both left and right wiper arm and blade.
1. Wiper arm assembly Acorn nut (3) Using 5/8-inch box-end wrench, unscrew
(1) to driver shaft (2) and take off.
TA244517
2-1301
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2. Driver shaft (1) Acorn nut (2) and a. Using 5/8-inch box-end wrench, un-
wiper arm (3) screw and take off.
b. Using 12-inch pinch bar, pry off.
3. Wiper arm (3) Driver nut (4) Using 3/8-inch flat-tip punch and 12-ounce
hammer, tap out.
4. Wiper arm (3) to Screw (6) and Using 1/4-inch, 1/4-inch drive socket and
wiper blade (5) nut (7) ratchet handle and 1/8-inch flat-tip screw-
driver, unscrew and take off.
INSTALLATION
7. Wiper arm (3) to Screw (6) and Screw on and tighten using 1/4-inch, 1/4-
wiper blade (5) nut (7) inch drive socket and ratchet handle and
1/8-inch flat-tip screwdriver.
10. Wiper arm (3) to Acorn nut (2) Screw on and tighten using 5/8-inch box-
driver shaft (1) end wrench.
]
ADJUSTMENT
NOTE
Make sure air pressure is approximately 70 psi (482.3 kPa) for correct adjustment.
11. Wiper arm (3) to Acorn nut (2) Using 5/8-inch box-end wrench, unscrew
driver shaft (1) and take off.
12. Driver shaft (1) Wiper arm (3) Using 12-inch pinch bar, pry off.
13. Wiper arm (3) Driver nut (4) Using 3/8-inch flat-tip punch and 12-
ounce hammer, tap out.
2-1302
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For proper adjustment of windshield wipers, windshield wiper switch must be turned to the
left to place windshield wipers in the park position.
14. Driver shaft (1) Driver nut (4) Place into position.
16. Wiper arm (3) to Acorn nut (2) Screw on and tighten using 5/8-inch box-
driver shaft (1) end wrench.
NOTE
Repeat steps 11 thru 16 until wiper blades stop 1 inch away from top of windshield.
NOTE
TA244518
2-1303
TM 5-3805-254-20-2
INITIAL SETUP
2-1304
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Steps 1, 2, and 3 are typical for removal of both inlet and outlet hoses.
2. Water pump (3) Shutoff valve (4) Using 8-inch slip-joint pliers, turn clock-
wise to close.
3. Water manifold (5) Shutoff valve (6) Using 8-inch slip-joint pliers, turn clock-
wise to close.
TA244519
2-1305
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Inlet hose (7) Hose clamp (8) Using 1/4-inch flat-tip screwdriver,
loosen.
6. Screw (9) Clamp (10), lock- a. Using 1/2-inch box-end wrench, un-
washer (11), and screw and take off.
nut (12) b. Take off clamp.
c. Get rid of lockwasher.
TA244520
2-1306
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
7. Support bracket (1) Screw (2), lock- a. Using two 7/16-inch box-end wrenches,
washer (3), and unscrew and take off.
nut (4) b. Get rid of lockwasher.
9. Under cab floor (7) Screw (8), lock- Using two 7/16-inch box-end wrenches,
washer (9), and unscrew and take off.
nut (10)
TA244521
2-1307
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
11. Inlet hose (5) Hose clamp (12) Using 1/4-inch flat-tip screwdriver,
loosen.
13. Preformed inlet Hose clamp (15) Using 1/4-inch flat-tip screwdriver,
hose (14) loosen.
15. Preformed inlet Hose clamp (17) Using 1/4-inch flat-tip screwdriver,
hose (14) loosen.
TA244522
2-1308
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
17. Outlet hose (1) Hose clamp (2) Using 1/4-inch flat-tip screwdriver,
loosen.
18. Shutoff valve (3) Outlet hose (1) and Take off.
hose clamp (2)
19. Screw (4) Clamp (5), lock- a. Using 1/2-inch box-end wrench, un-
washer (6), and screw and take off.
nut (7) b. Take off clamp.
c. Get rid of lockwasher.
TA244523
2-1309
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
20. Support bracket (8) Screw (9), lock- a. Using two 7/16-inch box-end wrenches,
washer (10), and unscrew and take off.
nut (11) b. Get rid of lockwasher.
22. Under cab Screw (14), lock- a. Using two 7/16-inch box-end wrenches,
floor (13) washer (15), and unscrew and take off.
nut (16) b. Get rid of lockwasher.
TA244524
2-1310
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
24. Outlet hose (1) Hose clamp (2) Using 1/4-inch flat-tip screwdriver,
loosen.
26. Preformed outlet Hose clamp (5) Using 1/4-inch flat-tip screwdriver,
hose (4) loosen.
28. Preformed outlet Hose clamp (7) Using 1/4-inch flat-tip screwdriver,
hose (4) loosen.
CLEANING
NOTE
2-1311
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and
gloves and use only in a well-ventilated area. Avoid contact with skin, eyes, and clothes
and do not breathe vapors. Do not use near open flame or excessive heat. The
flashpoint for type #1 drycleaning solvent is 100°F (38°C) and for type #2 is 138°F (59°C).
If you become dizzy while using cleaning solvent, get fresh air immediately, and get
medical aid. If contact with eyes is made, flush your eyes with water and get medical aid
immediately.
INSPECTION/REPLACEMENT
NOTE
32. All rubber parts Look for cracks, breaks, chafing, and
hardness.
34. All threaded parts Look for damaged threads and rounded
heads.
TA244526
2-1312
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps 60, 61, and 62 are typical for installation of both inlet and outlet hoses.
TA244527
2-1313
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
41. Support bracket (14) Clamp (13), screw a. Put clamp in place.
(15), new lock- b. Screw in and tighten using two 7/16-inch
washer (16), and box-end wrenches.
nut (17)
TA244528
2-1314
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
43. Stud (3) Clamp (2), new lock- a. Put clamp in place.
washer (4), and b. Screw on and tighten using 1/2-inch,
nut (5) box-end wrench.
44. Shutoff valve (6) Outlet hose (1) and Put on.
hose clamp (7)
45. Outlet hose (1) Hose clamp (7) Tighten using 1/4-inch flat-tip screwdriver.
TA244529
2-1315
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
47. Preformed inlet Hose clamp (10) Tighten using 1/4-inch flat-tip screwdriver.
hose (9)
49. Preformed inlet Hose clamp (12) Tighten using 1/4-inch flat-tip screwdriver.
hose (9)
51. Inlet hose (13) Hose clamp (14) Tighten using 1/4-inch flat-tip screwdriver.
TA244530
2-1316
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
53. Under cab floor (3) Clamp (2), screw a. Put clamp in place.
(4), new lockwasher b. Screw in and tighten using two 7/16-
(5), and nut (6) inch box-end wrenches.
55. Support bracket (8) Clamp (7), screw a. Put clamp in place.
(9), new lockwasher b. Screw in and tighten using two 7/16-
(10), and nut (11) inch box-end wrenches.
TA244531
2-1317
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
58. Shutoff valve (16) Inlet hose (1) and Put on.
hose clamp (17)
59. Inlet hose (1) Hose clamp (17) Tighten using 1/4-inch flat-tip screwdriver.
TA244532
2-1318
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
60. Water manifold (1) Shutoff valve (2) Turn counterclockwise to open using 8-inch
slip-joint pliers.
61. Water pump (3) Shutoff valve (4) Turn counterclockwise to open using 8-inch
slip-joint pliers.
NOTE
FOLLOW-ON MAINTENANCE:
TA244533
2-1319
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
1. Amber reflector (1) Screw (3) and Using number one cross-tip screwdriver and
to front fender (2) nut (4) 3/8-inch box-end wrench, unscrew and
take off.
INSTALLATION
4. New amber reflector Screw (3) and Screw in and tighten using number one
(1) to front nut (4) cross-tip screwdriver and 3/8-inch box-end
fender (2) wrench.
2-1320
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
2-1321
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Safety goggles must be worn, when using chisel and drill, to prevent eye injury caused by
flying steel chips.
NOTE
There are six reflectors on the dump body. The two front reflectors are amber; the four
rear reflectors are red. The four rear reflectors are initially installed with rivets.
TA244535
2-1322
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
4. New reflector (4) Two screws (5) Screw in and tighten using number two
to body (2) cross-tip screwdriver.
2-1323
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
NOTE
Tag all line fittings before removing for correct identification when installing.
For more information on how to tag parts, go to General Maintenance Instructions (page
2-424).
2-1324
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
4. Cover plate (6) to Six screws (8) Using number one cross-tip screwdriver,
front trim panel unscrew and take out.
head retainer (7)
TA244537
2-1325
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
7. Wiper mount bracket Two screws (5) Using number one cross-tip screwdriver,
(3) to front trim unscrew and take out.
panel head retainer (4)
9. Windshield wiper Two tee fittings (6) Using 1/2-inch open-end wrench, unscrew
motor (1) and take off.
12. Wiper mount bracket Two screws (9) Using number one cross-tip screwdriver,
(3) to windshield unscrew and take out.
wiper motor (1)
2-1326
TM 5-3805-254-20-2
TA244538
2-1327
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
16. Wiper mount bracket Two screws (3) Screw in and tighten using number one
(2) to windshield cross-tip screwdriver.
wiper motor (1)
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent
threaded parts from seizing.
NOTE
17. Windshield wiper Fitting (4) a. Wrap pipe threads with antiseizing tape.
motor (1) b. Screw in and tighten using 1/2-inch
open-end wrench.
18. Windshield wiper Adapter fitting (5) a. Wrap pipe threads with antiseizing tape.
motor(1) b. Screw in and tighten using 7/16-inch
box-end wrench.
19. Two tee fittings (6) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 1/2-inch
open-end wrench.
22. Wiper mount bracket Two screws (9) Screw in and tighten using number one
(2) to front trim cross-tip screwdriver.
panel head retainer (8)
23. Windshield wiper Five line a. Screw on and tighten using 9/16-inch
motor (1) fittings (10) open-end wrench.
b. Take tags off.
2-1328
TM 5-3805-254-20-2
TA244539
2-1329
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
25. Cover plate (2) to Six screws (3) Screw in and tighten using number one
front trim panel cross-tip screwdriver.
head retainer (1)
TA244540
2-1330
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244541
2-1331
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
32. Cover plate (1) to Six screws (3) Using number one cross-tip screwdriver,
front trim panel unscrew and take out.
head retainer (2)
34. Windshield wiper Three line a. Using 9/16-inch open-end wrench, un-
motor (4) fittings (5) screw and take off.
b. Tag line fittings.
35. Wiper mount bracket Two screws (8) Using number one cross-tip screwdriver,
(6) to front trim unscrew and take out.
panel head
retainer (7)
TA244542
2-1332
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
37. Windshield wiper Three elbow Using 1/2-inch open-end wrench, unscrew
motor (4) fittings (9) and take off.
TA244543
2-1333
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
40. Wiper mount bracket Two screws (4) Using number one cross-tip screwdriver,
(1) to windshield unscrew and take out.
wiper motor (3)
43. Wiper mount bracket Two screws (4) Screw in and tighten using number one
(1) to windshield cross-tip screwdriver.
wiper motor (3)
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal to prevent
threaded parts from seizing.
NOTE
44. Windshield wiper Fitting (5) a. Wrap pipe threads with antiseizing tape.
motor (3) b. Screw in and tighten using 1/2-inch
open-end wrench.
45. Windshield wiper Three elbow a. Wrap pipe threads with antiseizing tape.
motor (3) fittings (6) b. Screw in and tighten using 1/2-inch
open-end wrench.
2-1334
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
48. Wiper mount bracket Two screws (8) Screw in and tighten using number one
(1) to front trim cross-tip screwdriver.
panel head
retainer (7)
49. Windshield wiper Three line a. Screw on and tighten using 9/16-inch
motor (3) fittings (9) open-end wrench.
b. Take tags off.
TA244544
2-1335
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
51. Cover plate (2) to Six screws (3) Screw in and tighten using number one
front trim panel cross-tip screwdriver.
head retainer (1)
TA244545
2-1336
TM 5-3805-25420-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools Materials/Parts
TA244546
2-1337
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Cover plate (1) Six screws (2) Using number one cross-tip screwdriver,
unscrew and take out.
NOTE
Tag all line fittings before removing for correct identification when installing.
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
4 Fitting (4) Line fitting (5) a Using 5/8-inch open-end wrench, un-
screw and take off.
b Tag line fitting.
5 Elbow fitting (6) Line fitting (7) a Using 9/16-inch open-end wrench, un-
screw and take off.
b Tag line fitting.
6 T-fitting (8) Line fitting (9) a Using 9/16-inch open-end wrench, un-
screw and take off.
b Tag line fitting.
7 Adapter fitting (10) Line fitting (11) a Using 9/16-inch open-end wrench, un-
screw and take off.
b Tag line fitting.
2-1338
TM 5-3805-254-202
ACTION
LOCATION ITEM REMARKS
15 Windshield wiper Adapter fitting (10) Using 7/16-inch open-end wrench, un-
control (14) screw and take out.
16 Elbow fitting (18) Elbow fitting (6) Using 1/2-inch open-end wrench, unscrew
and take off.
17 Windshield wiper Elbow fitting (18) Using 9/16-inch open-end wrench, un-
control (14) screw and take out.
TA244547
2-1339
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
19 Windshield wiper Elbow fitting (2) a Wrap pipe threads with antiseizing tape.
control (1) b Screw in and tighten using 9/16-inch
open-end wrench.
20 Elbow fitting (2) Elbow fitting (3) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 1/2-inch
open-end wrench.
21 Windshield wiper Adapter fitting (4) a Wrap pipe threads with antiseizing tape.
control (1) b Screw in and tighten using 7/16-inch
open-end wrench.
23 T-fitting (5) Fitting (6) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 1/2-inch
open-end wrench.
24 T-fitting (5) to Fitting (7) a Wrap pipe threads with antiseizing tape.
windshield wiper b Screw in and tighten using 9/16-inch
control (1) open-end wrench.
2-1340
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
30 Adapter fitting (4) Line fitting (13) a Screw on and tighten using 9/16-inch
open-end wrench.
b Take off tag.
31 T-fitting (5) Line fitting (14) a Screw on and tighten using 9/16-inch
open-end wrench.
b Take off tag.
32 Elbow fitting (3) Line fitting (15) a Screw on and tighten using 9/16-inch
open-end wrench.
b Take off tag.
33 Fitting (7) Line fitting (16) a Screw on and tighten using 5/8-inch
open-end wrench.
b Take off tag.
36 Cover plate (9) Six screws (18) Screw in and tighten using number one
cross-tip screwdriver.
TA244548
2-1341
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Cover plate (1) Six screws (2) a Using number one cross-tip screw-
driver, unscrew and take out.
b Take down cover plate.
8 Elbow fitting (9) Line fitting (10) Using 9/16-inch open-end wrench, un-
to windshield washer screw and take off.
control (6)
2-1342
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9 Windshield washer Elbow fitting (9) Using 1/2-inch open-end wrench, unscrew
control (6) and take off.
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
13 Elbow fitting (9) to Line fitting (10) Screw on and tighten using 9/16-inch open-
windshield washer end wrench.
control (6)
TA244549
2-1343
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
16 Windshield washer Nut (4) Screw on and tighten using 5/8-inch open-
control (1) end wrench.
18 Windshield washer Setscrew (6) Screw in and tighten using 5/64-inch hex-
control knob (5) head wrench.
to cover plate (3)
TA244550
2-1344
TM 5-3805-254-20-2
INITIAL SETUP
Right side hood panel opened (page 2-424) Lockwasher, reservoir mounting bracket
(four required)
Tools
Personnel Required
Wrench, box-end, 7/16-inch
Wrench, open-end, 7/16-inch One
removed (page 2-424).
ACTION
LOCATION ITEM REMARKS
REMOVAL
TA702189
2-1344.1 Change 1
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
5 Strap (9) Four locknuts (10), a Using 7/16-inch open-end wrench and
lockwashers (11), 7/16-inch box-end wrench, unscrew, and
take off.
washers (12), and b Get rid of lockwashers.
bolts (13)
INSTALLATION
8 Strap (9) Four locknuts (10), Screw in and tighten, using 7/16-inch box-end
new lockwashers wrench and 7/16-inch open-end wrench.
(11), washers (12),
and bolts (13)
Change 1 2-1344.2
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
AIR HORN
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Molding (1) to Fourteen screws (3) Using number two cross-tip screwdriver,
head lining (2) unscrew and take out.
TA244551
2-1345
TM 5-3805-25420-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
6 Fitting (5) Line fitting (6) Using 9/16-inch open-end wrench, un-
screw and take off.
7 Air horn (7) Fitting (5) Using 9/16-inch open-end wrench, un-
screw and take out.
8 Air horn (7) to Two screws (8), two a Using number three cross-tip screw-
cab ceiling (3) nuts (9), and two driver and 7/16-inch open-end wrench,
lockwashers (10) with assistance, unscrew and take off.
b Get rid of lockwashers.
12 Yoke (13) to cab Screw (14), nut a Using number three cross-tip screw-
ceiling (3) (15), and lock- driver and 7/16-inch open-end wrench,
washer (16) with assistance, unscrew and take off.
b Get rid of lockwasher.
2-1346
TM 53805254-20-2
TA244552
2-1347
TM 5-3805-254-22
ACTION
LOCATION ITEM REMARKS
INSTALLATION
18 Nut (6) and new With assistance, using number three cross-
lockwasher (7) tip screwdriver and 7/16-inch open-end
wrench, screw on and tighten.
23 Air horn (8) to Two nuts (12) and With assistance, using number three cross-
cab ceiling (1) two new lock- tip screwdriver and 7/16-inch open-end
washers (13) wrench, screw on and tighten.
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
24 Air horn (8) Fitting (14) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 9/16-inch
open-end wrench.
25 Fitting (14) Line fitting (15) Screw on and tighten using 9116-inch open-
end wrench.
2-1348
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
30 Molding (19) to Fourteen screws (20) With assistance, using number two cross-
head lining (17) tip screwdriver, screw in and tighten.
TA244553
TASK ENDS HERE
2-1349
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
NOTE
Step 1 is typical for the removal of all data and instruction plates attached with adhesive.
1. Automatic override Four nuts (2) and a. Tag wires.
WARNING
Safety goggles must be worn when using a portable electric drillFlying metal particles can cause eye
injury.
NOTE
Steps 2 and 3 are typical for the removal of all data and instruction plates attached with rivets.
2-1350
TM 5-3805-254-20-2
2 Door frame (3) Four rivets (4) and a Using 1/8-inch drill bit and 1/4-inch
data plate (5) portable electric drill, drill out rivets.
b Take off data plate.
3 Right side kick Nine screws (7) a Using number two cross-tip screw-
panel (6) driver, unscrew and take out.
b Take off right side kick panel.
TA244554
2-1351
TM 5-3805-25420-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
4 Heater box (1) Five rivets (2) and a Using 5/32-inch drill bit and 1/4-inch
wiring circuit portable electric drill, drill out rivets.
diagram plate (3) b Take off wiring circuit diagram plate.
CLEANING
WARNING
Naphtha and its fumes are harmful and flammable. Do not use near open flame. Do not smoke while
using naphtha. Use only in well-ventilated area. Naphtha can catch fire, and fumes can explode causing
injury.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
5 Inside driver’s Old adhesive (5) Using naptha and rag, clean off old
door (4) adhesive.
TA244555
2-1352
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
NOTE
Steps given are typical for installation of all data and instruction plates attached with adhesive and screws.
8 New data plate (9) Four self-tapping Screw in and tighten using number one
screws (10) cross-tip screwdriver.
2-1353 TA244556
TM 5-3805.254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
10 Right side kick Nine screws (4) a Put right side kick panel in place.
panel (3) b Screw in and tighten using number two
cross-tip screwdriver.
NOTE
FOLLOW-ON MAINTENANCE: Close right and left cab doors (page 2-424).
2-1354
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1 Lever (1) Cotter pin (2) and a Using 6-inch slip-joint pliers take out
pull chain (3) cotter pin.
b Take off pull chain.
c Get rid of cotter pin.
TA244558
2-1355
TM 5-3805-254-20.2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
2 Head panel (1) Screw (2) and pull Using number one cross-tip screwdriver,
chain (3) unscrew and take off.
3 Panel (4) Two screws (5) and Using number one cross-tip screwdriver,
cover (6) unscrew and take off.
4 Air horn control Two screws (8) Using number one cross-tip screwdriver,
valve (7) unscrew and take out.
5 Panel (9) Two screws (10) Using number one cross-tip screwdriver,
unscrew and take out.
CAUTION
Use care when removing bracket, damage to air lines may result.
For more information on how to tag parts, go to General Maintenance Instructions (page 2-424).
9 Air line (19) Line nut (20) and a Tag air line.
air horn control b Using 1/2-inch and 5/8-inch open-end
valve (7) wrenches, unscrew and take off.
c Take out air horn control valve.
2-1356
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
10 Air horn Control Elbow Fitting (21) Using 1/2-inch open-end wrench, unscrew
valve (7) and take off.
TA244559
2-1357
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
ASSEMBLY
NOTE
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
For more information on how to use antiseizing tape, go to General Maintenance Instructions.
2-1358
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
16 Air horn control Elbow fitting (2) a Wrap pipe threads with antiseizing tape.
valve (1) b Screw on and tighten using 1/2-inch
open-end wrench.
17 Locknut (4) and tee a Wrap pipe threads with antiseizing tape.
fitting (5) b Screw locknut on to tee fitting until
locknut reaches end of threads.
c Screw in tee fitting until snug, and
tighten 2 turns using 1/2-inch open-
end wrench.
d Tighten locknut using 13/16-inch and
1/2-inch open-end wrenches.
TA244560
2-1359
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
19 Access hole (1) and Bracket (3) and two a Put in bracket and aline holes in bottom
panel (2) screws (4) of bracket with holes in panel (2).
b Screw in two screws using number one
cross-tip screwdriver.
Do not tighten.
20 Elbow fitting (5) Line nut (6) a Screw on using 9/16-inch open-end
wrench.
Do not tighten.
b Take off tag.
c Get rid of tag.
21 Elbow fitting (7) Line nut (8) a Screw on using 5/8-inch open-end
wrench.
Do not tighten.
b Take off tag.
c Get rid of tag.
22 Tee fitting (9) Line nut (10) a Screw on using 5/8-inch open-end
wrench.
Do not tighten.
b Take off tag.
c Get rid of tag.
23 Bracket (3) Air horn control a Put in while alining lever (13) with hole
valve (11), and in lever (14).
two screws (12) b Screw in two screws and tighten
using number one cross-tip screw-
driver.
24 Panel (2) Two screws (4) Tighten, using number one cross-tip
screwdriver.
25 Elbow fitting (5) Line nut (6) Tighten, using 9/16-inch and 1/2-inch
open-end wrenches.
26 Elbow fitting (7) Line nut (8) Tighten, using 5/8-inch and 11/16-inch
open-end wrenches.
2-1360
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
27 Tee fitting (9) Line nut (10) Tighten, using 518-inch and 1/2-inch
open-end wrenches.
29 Head panel (18) Pull chain (19) a Put pull chain in position.
and screw (20) b Screw in and tighten using number one
cross-tip screwdriver.
30 Lever (1) Pull chain (19) and a Put pull chain in place.
new cotter pin (21) b Put in and bend ends back using 6-inch
slip-joint pliers
TA244561
TASK ENDS HERE
2-1361
TM 5-3805-254-20-2
Page Page
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not drain hydraulic oil when hot. Hot oil can burn you.
2-1362
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
2 Filter housing (3) Drainplug (4) Using 7/16-inch open-end wrench, un-
screw and take out.
3 Filter head (5) to Four screws (6) Using 5/8-inch 1/2-inch drive socket, 10-
filter housing (3) inch extension, and ratchet handle, un-
screw and take out.
TA244562
2-1363
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
WARNING
Particles blown by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
7 All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1364
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
12 Filter head (4) to Four screws (5) Screw in and tighten using 5/8-inch 1/2-
filter housing (1) inch drive socket, 10-inch extension, and
ratchet handle.
TA244563
2-1365
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
13 Filter housing (1) Drainplug (2) a. Wrap pipe threads with antiseizing tape.
b. Screw in and tighten using 7/16-inch
open-end wrench.
TA244564
TASK ENDS HERE
2-1366
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
1. Clevis (1) Nut (2) Using 3/4-inch open-end wrench and 8-
inch slip-joint pliers, loosen one turn.
TA244565
2-1367
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
NOTE
Count threads on rod before removing clevis, for correct adjustment when installing.
2. Rod (1) Clevis (2) Using two 8-inch slip-joint pliers, unscrew
and take off.
4. Clamp (4) Two nuts (5) and a. Using 7/16-inch box-end wrench, un-
two lockwashers (6) screw and take off.
b. Get rid of lockwashers.
6. Control valve (8) Cotter pin (10) a. Using 6-inch long-nose pliers,
and clevis pin (9) straighten ends and take out.
b. Get rid of.
7. Control valve (8) Clevis pin (9) Using 8inch slip-joint pliers, take out.
TA244566
2-1368
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
two lockwashers (13) screw and take off.
b. Get rid of lockwashers.
11. Clamp (14) Two nuts (15) and a. Using 7/16-inch box-end wrench, un-
two lockwashers (16) screw and take off.
b. Get rid of lockwashers.
TA244567
2-1369
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
18 Pin (3) New cotter pin (4) Put in and bend back ends using 6-inch long
nose pliers.
19. Rod (2) Nut (5) Screw on com pletely using 3/4-inch open-
end wrench and 8-inch slip-joint pliers.
22. Pin (7) Cotter pin (8) a. Using 6-inch long-nose pliers,
straighten ends and take out.
b. Get rid of.
23. Clevis (6) Nut (5) Using 3/4-inch open-end wrench and 8-
inch slip-joint pliers, loosen four turns.
24. Cab floor (9) Dump body control Have assistant put in and hold in neutral
lever (10) position.
2-1370
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
25. Dump body control Pin (7) and a. Put pin through clevis and dump body
lever arm (11) clevis (6) control lever arm (11).
b. Check that pin moves freely.
c. If pin does not move freely, take out pin
and turn clevis in or out to adjust.
d. Put pin back in.
27. Clevis (6) Nut (5) Tighten using 3/4-inch open-end wrench
and 8-inch slip-joint pliers.
TA244568
2-1371
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
28. Eye (1) Cable (2) Put through and bend over.
30. Clamp (3) Two new lockwashers Screw on and tighten using 7/16-inch box-
(4) and two nuts (5) end wrench.
TA244569
2-1372
TM 5-3805-254-20-2
WARNING
To prevent injury, make sure all personnel are clear of tailgate when body is in raised position.
CAUTION
Do not hold dump body control lever in back position for any length of time when hydraulic cylinder is fully
extended.
NOTE
32. Dump truck (7) Dump body (8) a. Raise (page 2-424).
b. Measure from cylinder top pin using 25
foot steel tape measure.
c. Lower 6 inches (15.24 cm).
d. Block in lowered 6-inch position.
e. Hold dump body control lever in neutral
position.
TA244570
2-1373
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
33. Eye (1) Cable (2) Pull to rear and bend over.
35. Clamp (3) Two new lockwashers Screw on and tighten using 7/16-inch box-
(4) and two nuts (5) end wrench.
39. Clamp (9) Two new lockwashers Screw on and tighten using 7/16-inch box-
(10) and two end wrench.
nuts (11)
TA244571
2-1374
TM 5-3805-254-20-2
NOTE
INITIAL SETUP
Tools Materials/Parts
2-1375
TM 5-3805-254-20-2
REMOVAL
7. Two straps (10) and Two nuts (11) and a. Using 20-ton hydraulic floor jack, have
eservoir (1) two lockwashers (12) two assistants hold reservoir.
b. Using 15/16-inch open-end wrench,
unscrew and take off.
c. Get rid of lockwashers.
CAUTION
Use care when removing reservoir and fittings, damage could occur.
8. Two straps (10) Reservoir (1) With assistance, using 20-ton hydraulic
floor jack, take down and out.
2-1376
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY
9. Reservoir (1) Cap (13) Take off.
10. Valve (2) Nipple (5) Using 1 7/8-inch open-end and 18-inch
pipe wrenches, unscrew and take out.
11. Nipple (14) Valve (2) Using 1 7/8-inch open-end and 18-inch
pipe wrenches, unscrew and take off.
12. Elbow (15) Nipple (14) Using two 18-inch pipe wrenches, unscrew
and take out.
13. Reservoir (1) Elbow (15) Using 18-inch pipe wrench, unscrew and
take out.
TA244572
2-1377
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
DISASSEMBLY - CONTINUED
14. Two elbows (1) Two nuts (2) and Using 9/16-inch and 5/8-inch open-end
sight glass (3) wrenches, unscrew and take out.
16. Reservoir (4) Two elbows (1) Using 9/16-inch open-end wrench, un-
screw and take out.
17. Bushing (5) Union (6) Using 1 1/2-inch and 1 3/4-inch open-end
wrenches, unscrew and take out.
18. Elbow (7) Bushing (5) Using 1 3/4-inch open-end and 18-inch
pipe wrenches, unscrew and take out.
19. Filter housing (8) Elbow (7) Using 18-inch pipe wrench, unscrew and
take out.
21. Reservoir (4) Filter housing (8), a. Using 5/16-inch hex key, unscrew and
four hex-head take out.
screws (10), and b. Get rid of ring.
ring (11) c. Set filter housing aside for assembly.
22. Nipple (12 Filter housing Using 18-inch pipe wrench, unscrew and
flange (13) take off.
23. Reservoir (4) Nipple (12) Using 18-inch pipe wrench, unscrew and
take out.
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
2-1378
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do not
use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F (380C)
and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
24. All metal parts Using drycleaning solvent and wiping rag,
clean thoroughly.
TA244573
2-1379
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
25. All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
26. Reservoir (1) a. Look for holes or large dents.
b. Look for cracks in welded areas.
c. Look for pitted areas inside.
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
2-1380
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
30. Reservoir (1) Two elbows (4) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 9/16-inch
open-end wrench.
32. Two elbows (4) Sight glass (2) and a. Put in place.
two nuts (5) b. Screw in and tighten using 9/16-inch
and 5/8-inch open-end wrenches.
33. Reservoir (1) Nipple (6) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 18-inch pipe
wrench.
34. Nipple (6) Filter housing Screw on and tighten using 18-inch pipe
flange (7) wrench.
TA244574
2-1381
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
36. Filter housing (1) Two screws (2) Screw in and tighten using 3/4-inch open-
end wrench.
38. Elbow (3) Bushing (4) a. Wrap pipe threads with antiseizing tape
(page 2424).
b. Screw in and tighten using 1 3/4-inch
open-end and 18-inch pipe wrench.
39. Bushing (4) Union (5) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 1 11/2-inch
and 1 3/4-inch open-end wrenches.
40. Reservoir (6) Elbow (7) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 18-inch pipe
wrench.
41. Elbow (7) Nipple (8) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using two 18-inch
pipe wrenches.
42. Nipple (8) Valve (9) Screw in and tighten using 1 7/8-inch open-
end and 18-inch pipe wrenches.
43. Valve (9) Nipple (10) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 1 7/8-inch
open-end and 18-inch pipe wrenches.
44. Filter housing (1) Drainplug (11) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 7/16-inch
open-end wrench.
2-1382
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when installing reservoir, damage to reservoir or fittings could occur.
NOTE
45 Two straps (12) Reservoir (6) With two assistants, put in place and hold
using 20-ton hydraulic floor jack.
47 Union (5) Hose (15) Screw in and tighten using 1 3/8-inch and
1 1/2-inch open-end wrenches.
2-1383
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
50 Reservoir (3) Filler neck (4) a Fill with lubricating oil until sight
and cap (5) glass (6) is full.
b. Put cap on reservoir.
TA24576
TASK ENDS HERE
2-1384
TM 53805-254-20-2
INITIAL SETUP
2-1385
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not drain hydraulic oil when hot. Hot oil could burn you.
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do not
use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F (380C)
and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
2-1386
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Particles blown by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
8. All parts Using blow gun and air hose assembly, blow
dry.
TA244577
2-1387
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
12. Valve (5) Bushing (3) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 1 3/8-inch
open-end wrench.
13. Bushing (3) Elbow (1) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 1 1/4-inch
and 1 3/8-inch open-end wrenches.
14. Elbow (1) Hose (4) Screw in and tighten using two 1 114-inch
open-end wrenches.
15. Pump (6) Elbow (2) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using two 1 114-
inch open-end wrenches.
16. Elbow (2) Hose (4) Screw in and tighten using two 1 1/4-inch
open-end wrenches.
18. Reservoir (8) Cap (9) Turn counterclockwise and take off.
19. Filler neck (10) Fill with lubricating oil until sight glass (11)
is full.
2-1388
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244578
2-1389
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not drain hydraulic oil when hot. Hot oil could burn you.
2-1390
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
6. Elbow (8) Nipple (7) Using two 18-inch pipe wrenches, unscrew
and take out.
7. Elbow (9) Elbow (8) Using two 18-inch pipe wrenches, unscrew
and take out.
TA244579
2-1391
TM 5-3805-254-2-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do not
use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F (380C)
and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
WARNING
Particles blow by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning pruposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
11. All parts Using blow gun and air hose assembly, blow
dry.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1392
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
15. Pump (6) Elbow (2) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using 18-inch pipe
wrench.
16. Elbow (2) Elbow (3) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using two 18-inch
pipe wrenches.
17. Elbow (3) Nipple (5) a. Wrap pipe threads with antiseizing tape
(page 2-424).
b. Screw in and tighten using two 18-inch
pipe wrenches.
2-1393
RESERVOR-TO-PUMP SUCTION HOSE AND FITTINGS - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
24. Filler neck (8) Fill with lubricating oil (LO 5-3805-254-12)
until sight glass (10) is full.
26. Reservoir (5) Cap (7) Put in place and turn clockwise.
TA244581
TASK ENDS HERE
2-1394
TM 5-3805-254-20-2
INITIAL SETUP
Tools
Brush, cleaning
Container, 6-gallon Materials/Parts - Continued
Gloves, safety
Goggles, safety Rags, wiping (item 15, appendix C)
Gun, blow, air Solvent, drycleaning (item 19, appendix C)
Hose, air assembly Tape, antiseizing (item 22, appendix C)
Wrench, box-end, 1 5/8-inch
Wrench, open-end, 1 38-inch Personnel Required
Wrench, open-end, 111/2-inch
One
Materials/Parts
References
Detergent, liquid, GP (item 7,
appendix C) LO 5-3805-254-12 (Lubrication Order)
Oil, lubricating (item 14, appendix C)
2-1395
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
REMOVAL
WARNING
Do not drain hydraulic oil when hot. Hot oil could burn you.
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 1000F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
2-1396
TM 5-3805-254.20-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
NOTE
For more information on how to clean parts, go to General Maintenance Instructions(page 2-424).
TA244564
2-1397
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING - CONTINUED
WARNING
Particles blown by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
7 All parts Using blow gun and air hose assembly, blow
dry.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
11 Valve (4) Bushing (2) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 5/8-inch
box-end wrench.
12 Bushing (2) Elbow (1) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 1/2-inch
and 1 5/8-inch open-end wrenches.
13 Elbow (1) Hose (3) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 3/8-inch
and 1 1/2-inch open-end wrenches.
2-1398
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
16 Filler neck (8) Fill with lubricating oil until sight glass (9) is
full.
TA244583
2-1399
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts - Continued
Materials/Parts References
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Do not drain hot hydraulic oil Hot oil could burn you.
2 Elbow (3) Union (1) Using 1 1/2-inch open-end wrench and 18-
inch pipe wrench, unscrew and take out.
2-1400
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
3 Fitting (4) Elbow (3) Using 1 3/8-inch open-end wrench and 18-
inch pipe wrench, unscrew and take out.
6 Elbow (7) Elbow (6) Using 1 1/2-inch open-end wrench and 18-
inch pipe wrench, unscrew and take out.
7 Nipple (8) Elbow (7) Using 18-inch pipe wrench, unscrew and
take out.
TA244584
2-1401
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
9 Elbow (3) Elbow (1) Using 1 1/2-inch open-end wrench and 18-
inch pipe wrench, unscrew and take out.
10 Nipple (4) Elbow (3) Using 18-inch pipe wrench, unscrew and
take out.
TA244585
2-1402
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
9. Clamp (11) Two nuts (12) and a. Using 7/16-inch box-end wrench, un-
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Wear protective safety goggles and gloves and use
only in a well-ventilated area. Avoid contact with skin, eyes, and clothes and do not breathe vapors. Do
not use near open flame or excessive heat. The flashpoint for type #1 drycleaning solvent is 100°F
(380C) and for type #2 is 138°F (590C). If you become dizzy while using cleaning solvent, get fresh air
immediately, and get medical aid. If contact with eyes is made, flush your eyes with water and get medical
aid immediately.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Particles blown by compressed are hazardous Make certain the airstream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa)
User must wear safety goggles or face shield to prevent injury to personnel.
2-1403
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTIONIREPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions.
18 Union (1) Hose (2) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 3/8-inch
and 1 1/2-inch open-end wrenches.
19 Nipple (3) Elbow (4) Screw in and tighten using 18-inch pipe
wrench.
20 Elbow (4) Elbow (5) a Wrap pipe threads with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 1/2-inch
open-end wrench and 18-inch pipe
wrench.
21 Elbow (5) Hose (2) a Wrap pipe thread with antiseizing tape
(page 2-424).
b Screw in and tighten using 1 3/8-inch
and 1 1/2-inch open-end wrenches.
22 Nipple (3) Elbow (6) Screw in and tighten using 18-inch pipe
wrench.
2-1404
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
23 Elbow (6) Elbow (7) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 1 11/2-inch
open-end wrench and 18-inch pipe
wrench.
24 Elbow (7) Hose (8) a Wrap pipe threads with antiseizing tape
b Screw in and tighten using 1 3/8-inch
and 1 1/2-inch open-end wrenches.
25Valve (9)Fitting (10)aWrap pipe threads
with antiseizing tape.
b Screw in and tighten using 1 3/8-inch
box-end wrench.
27 Elbow (11) Union (12) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 1 1/2-inch
open-end wrench and 18-inch pipe
wrench.
28 Union (12) Hose (8) a Wrap pipe threads with antiseizing tape.
b Screw in and tighten using 1 318-inch
and 1 1/2-inch open-end wrenches.
TA244586
2-1405
TM 53805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
31 Filler neck (3) Fill with lubricating oil until sight glass (4) is
full.
TA244587
2-1406/(2-1407 blank)
TM 5-3805-254-20-2
Page Page
SPEEDOMETER
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
2-1408
TM 5-3805.254-20-2
SPEEDOMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
Hold speedometer against lower center instrument panel when performing steps 4 and 5.
4 Mounting bracket (5) Two nuts (6) and a Using 3/8-inch open-end wrench, un-
two lockwashers (7) screw and take off.
b Get rid of lockwashers.
TA244588
2-1409
TM 5380525420-2
SPEEDOMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSPECTIONIREPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
11 Mounting bracket (2) Two new lockwashers Screw on and tighten using 3/8-inch open-
(4) and two nuts (5) end wrench.
2-1410
TM 5-3805-254-20-2
SPEEDOMETER - CONTINUED
NOTE
FOLLOW-ON MAINTENANCE:
TACHOMETER
INITIAL SETUP
Tools Personnel Required
TA244589
2-1411
TM 5-3805-254-20-2
TACHOMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
Hold tachometer against lower center instrument panel when performing steps 4 and 5.
4 Mounting bracket (5) Two nuts (6) and a Using 3/8-inch open-end wrench, un-
two lockwashers (7) screw and take off.
b Get rid of lockwashers.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1412
TM 5-3805-254-20-2
TACHOMETER - CONTINUED
ACTION
LOCATION ITEM REMARKS
INSTALLATION
11 Mounting bracket (5) Two new lockwashers Screw on and tighten using 3/8-inch open-
(7) and two nuts (6) end wrench.
NOTE
FOLLOW-ON MAINTENANCE:
1.Close lower center instrument panel (page 2-424)
2.Close left side cab door (page 2-424).
TA244590
2-1413
TM 53805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
3. Two extensions (5) Two clips (6), two a Using two 7/16-inch box-end wrenches,
nuts (7), two lock- unscrew and take out.
washers (8), and two b Get rid of lockwashers.
screws (9)
2-1414
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
5. Left frame rail (10) Speedometer drive Push up over automatic transmission
cable (4) harness.
Make sure automatic transmission
harness is clear of speedometer drive
cable.
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
TA244591
2-1415
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
10 Extension (6) Clip (7), nut (8), a Using two 7/16-inch box-end wrenches,
lockwasher (9), and unscrew and take out.
screw (10) b Get rid of lockwasher.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instruction (page 2-424).
INSTALLATION
16 Engine side of Speedometer drive Put small end through speedometer drive
firewall (4) cable (3) cable hole.
2-1416
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
TA244592
2-1417
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
22 Extension (6) Clip (5), screw (7), Screw in and tighten using two 7/16-inch
new lockwasher (8), box-end wrenches.
and nut (9)
TA244593
2-1418
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
24. Extension (1) Two clips (2), two Screw in and tighten using two 7116-inch
screws (3), two new box-end wrenches.
lockwashers (4), and
two nuts (5)
NOTE
FOLLOW-ON MAINTENANCE:
1. Close lower center instrument panel (page 2-424).
2. Close left side cab door (page 2-424).
3. Close left side hood panel (page 2-424).
4. Install air cleaner housing panel (page 2-452).
2-1419 TA244594
TM 53805254-20-2
INITIAL SETUP
Tools Personnel Required
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
2-1420
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244595
2-1421
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
16 Fuel filter Tachometer drive Put large end through grommet hole.
bracket (4) cable (2)
2-1422
TM 5.3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244596
2-1423
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
21 Engine side of Tachometer drive Push through tachometer drive cable hole.
firewall (4) cable (2)
23 Engine side of Grommet retainer Screw in and tighten using number two
firewall (4) halves (6), two cross-tip screwdriver.
new lockwashers
(7), and two
screws (8)
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
2-1424
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
TA244597
2-1425
TM 53805-2520-2
INITIAL SETUP
Tools Personnel Required
ACTION
LOCATION ITEM REMARKS
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
2-1426
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
TA244598
2-1427
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
12. Mounting bracket (3) Two new lockwashers Screw on and tighten using 3/8-inch open-
(4) and two nuts (5) end wrench.
13. Gage (2) Adapter (6) Screw on and tighten using 9/16-inch open-
end wrench.
14. Adapter (6) Line (7) Screw on and tighten using two 9/16-inch
open-end wrenches.
NOTE
FOLLOW-ON MAINTENANCE:
2-1428
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
2-1429
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
NOTE
Tag all light sockets, wires, lines and cables before removing, for correct identification when installing.
2-1430
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244601
2-1431
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
13. Gage (3) Adapter (1) Using 9/16-inch open-end wrench, un-
screw and take off.
14. 90-degree elbow (4) Line (2) Using 1/2-inch and 9/16-inch open-end
wrenches, unscrew and take off.
15. Bulkhead fitting (5) 90-degree elbow (4) Using 1/2-inch open-end wrench, unscrew
and take out.
17. Lower left side of 90-degree elbow (6) Using 1/2-inch open-end wrench, unscrew
cylinder block (8) and take out.
TA244602
2-1432
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
18. Airhose (9), fuel Electrical tiedown a. Using 6-inch diagonal-cutting pliers,
hose (10), and strap (11) cut and take off.
line (7) b. Get rid of strap.
19. Bracket (12) Nut (13), lockwasher a. Using two 7116-inch open-end
(14), clamp (15), and wrenches, unscrew and take out.
screw (16) b. Get rid of lockwasher.
20. 90-degree elbow (17) Line (7) Using 1/2-inch and 9/16-inch open-end
wrenches, unscrew and take off.
TA244603
2-1433
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
22. 45-degree elbow (4) Oil pressure Using 7/16-inch open-end wrench, un-
switch (1) screw and take out.
NOTE
23. Bulkhead fitting Nut (7) Using 1-inch open-end wrench, hold nut
(5) engine side of from turning.
firewall (6)
TA244604
2-1434
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
24. Bulkhead fitting (5) Nut (9) and flat Using 1/2-inch drive, 1 118-inch deep
and driver’s side of washer (10) socket, 10-inch extension, and ratchet
firewall (8) handle, unscrew and take off.
TA244605
2-1435
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
CAUTION
Use care when removing fittings and flat washer, to prevent damage.
NOTE
Before removing fittings and flat washer, make sure to note location and position of 45 and 90-degree
elbows, for correct assembly.
DISASSEMBLY
26. T-fitting (3) 45-degree elbow (2) Using two 9/16-inch open-end wrenches,
unscrew and take out.
2-1436
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
30. Bulkhead fitting (7) Straight pipe Using 7/16-inch and 1-inch open-end
fitting (5) wrenches, unscrew and take out.
31. Small nut (8) and Using 1-inch and 1 1/8-inch open-end
large nut (6) wrenches, unscrew and take off.
TA244607
2-1437
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
WARNING
Particles blown by compressed air are hazardous. Make certain the airstream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
33. All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
36. Lines (1) and Flare seats Look for cracks, bends, or dents.
elbow (9)
2-1438
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts
from seizing.
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
38. Bulkhead Small nut (6) Screw on and tighten using 1-inch and
fitting (5) and large nut (7) 1 1/8-inch open-end wrenches.
40. Large nut (7) Unscrew and take off using 1-inch and
1 1/8-inch open-end wrenches.
41. Straight pipe T-fitting (8) Screw on and tighten using 7/16-inch and
fitting (4) 9/16-inch open-end wrenches.
42. 90-degree elbow (9) Wrap pipe threads with antiseizing tape.
and 45-degree
elbow (10)
2-1439
2-1439
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
ASSEMBLY - CONTINUED
NOTE
Make sure 45 and 90-degree elbows are assembled in same position and location as noted in removal.
43. T-fitting (1) 90-degree Screw in and tighten using 1/2-inch and
elbow (2) 9/16-inch open-end wrenches.
46. Small nut (6) Turn small nut until a few threads can be
seen on T-fitting side of bulkhead.
INSTALLATION
47. Engine side of Bulkhead fitting Put into bulkhead fitting hole.
firewall (7) (4), small nut (6),
flat washer (5),
straight pipe fitting
(8), T-fitting (1),
45-degree elbow (3),
and 90-degree
elbow (2)
TA244609
2-1440
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
48. Engine side of Small nut (6) Hold nut from turning using 1-inch open-
firewall (7) end wrench.
50. Large nut (11) Screw on and tighten using 1/2-inch drive,
1 1/8-inch deep socket, 10-inch extension
and ratchet handle.
TA244610
2-1441
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
52. 45-degree elbow (2) Oil pressure Screw in and tighten using 7/16-inch open-
switch (1) end wrench.
53. Oil pressure Five wires (3) Put wires under correct screw heads.
switch (1)
55. 90-degree elbow (5) Line (6) Screw on and tighten using 112-inch and
9/16-inch open-end wrenches.
57. Bracket (8) Screw (9), clamp Screw in and tighten using two 7/16-inch
(7), new lockwasher open-end wrenches.
(10. and nut (11)
TA244611
2-1442
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
59. 90-degree elbow (15) Wrap pipe threads with antiseizing tape
(page 2-424).
60. Lower left side of 90-degree elbow (15) Screw in and tighten using 1/2-inch open-
cylinder block (16) end wrench.
61. 90-degree elbow (15) Line (6) a. Screw on and tighten using 1/2-inch and
9/16-inch open-end wrenches.
b. Get rid of tone
TA244612
2-1443
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
62. 90-degree elbow (1) Wrap pipe threads with antiseizing tape.
63. Driver’s side 90-degree elbow (1) Screw in and tighten using 1/2-inch open-
of firewall (2) end wrench.
and bulkhead
fitting (3)
64. 90-degree elbow (1) Line (4) Screw on and tighten using 1/2-inch and
9/16-inch open-end wrenches.
65. Gage (5) Adapter (6) Screw on and tighten using 9/16-inch open-
end wrench.
66. Adapter (6) Line (4) a. Screw on and tighten using two 9/16-
inch open-end wrenches.
b.Get rid of tag.
TA244613
2-1444
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244614
2-1445
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
TA244615
2-1446
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
2-1447
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
INSTALLATION
2-1448
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13. Two new lockwashers Screw on and tighten using 3/8-inch open-
(6) and two nuts (5) end wrench.
14. Gage (1) Elbow (3) Screw on and tighten using 9/16-inch open-
end wrench.
Position as shown.
15. Elbow (3) Line (4) Screw on and tighten using two 9/16-inch
open-end wrenches.
NOTE
FOLLOW-ON MAINTENANCE:
2-1449
TM 5-3805-254-20-2
INITIAL SETUP
Tools Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind lower center instrument panel to prevent breaking or disconnecting wires.
NOTE
Tag all light sockets, lines, wires, and cables before removing for correct identification when installing.
For more information on how to tag parts, go to General Maintenance Instructions {page 2-424).
2-1450
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244617
2-1451
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
13. Gage (11) 90-degree elbow (9) Using 9/16-inch open-end wrench, un-
screw and take off.
TA244618
2-1452
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
14. 90-degree elbow (12) Line (10) Using 1/2-inch and 9/16-inch open-end
wrenches, unscrew and take off.
15. Bulkhead 90-degree elbow (12) Using 1/2-inch open-end wrench, unscrew
fitting (13) and take out.
16. 45-degree elbow(14) Line (15) Using 7/16-inch and 9/16-inch open-end
wrenches, unscrew and take off.
TA244619
2-1453
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
17. Bulkhead 45-degree elbow (2) Using 7/16-inch open-end wrench, un-
fitting (1) screw and take out.
NOTE
18. Bulkhead fitting (1) Nut (4) Using 1-inch open-end wrench, hold nut
on engine side of from turning.
firewall (3)
19. Bulkhead fitting (1) Nut (6) and Using 1/2-inch drive, 1 1/8-inch deep
on driver’s side of flat washer (7) socket, 10-inch extension, and ratchet
TA244620
2-1454
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
21. Bracket (9) Nut (10), lockwasher a. Using two 7/16-inch open-end
(11), clamp (12), wrenches, unscrew and take out.
and screw (13) b. Get rid of lockwasher.
22. Brackets (14) Nuts (15), lock- a. Using two 7/16-inch open-end
washers (16), wrenches, unscrew and take out.
clamps (17), and b. Get rid of lockwashers.
screws (18)
TA244621
2-1455
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
23. Straight pipe Line (2) Using 7/16-inch and 9/16-inch open-end
fitting (1) wrenches, unscrew and take off.
24. T-fitting (3) Straight pipe Using 7/16-inch and 9/16-inch open-end
fitting (1) wrenches, unscrew and take out.
27. T-fitting (3) Oil pressure Using two 9/16-inch open-end wrenches,
switch (4) unscrew and take out.
28. Straight pipe T-fitting (3) Using 7/16-inch and 9/16-inch open-end
fitting (7) wrenches, unscrew and take off.
29. Torque converter Straight pipe Using 7/16-inch open-end wrench, un-
housing (8) fitting (7) screw and take out.
TA244622
2-1456
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
Particles blown by compressed air are hazardous Make certain the airstream is directed away from user
and other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa) User must wear safety goggles or face shield to prevent injury to personnel.
31 All parts Using air blow gun and air hose assembly,
blow dry.
INSPECTION/REPLACEMENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
2-1457
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
34 Lines (1) and Flare seats (3) Look for cracks, bends, or dents.
fittings (2)
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from
seizing.
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-424).
36 Torque converter Straight pipe Screw in and tighten using 7/16-inch open-
housing (4) fitting (3) end wrench.
TA244623
2-1458
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
37 Straight pipe T-fitting (5) Screw on and tighten using 7/16-inch and
fitting (3) 9/16-inch open-end wrenches.
39 T-fitting (5) Oil pressure Screw in and tighten using two 9/16-inch
switch (6) open-end wrenches.
NOTE
40 Oil pressure Two wires (7) and a Screw in and tighten using 3/16-inch
switch (6) two screws (8) flat-tip screwdriver.
b Get rid of tags.
42 T-fitting (5) Straight pipe Screw in and tighten using 7/16-inch and
fitting (9) 9/16-inch open-end wrenches.
43 Straight pipe Line (10) Screw on and tighten using 7/16-inch and
fitting (9) 9/16-inch open-end wrenches.
TA244626
2-1459
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
45 Brackets (3) Nuts (4), new Screw in and tighten using two 7/16-inch
lockwashers (5), open-end wrenches.
clamps (2), and
screws (6)
47 Bracket (8) Nut (9), new Screw in and tighten using two 7/16-inch
lockwasher (10), open-end wrenches.
clamp (7), and
screw (11)
48 Bulkhead Small nut (13) Screw on until a few threads can be seen at
fitting (12) one end.
2-1460
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
51 Small nut (13) Hold nut from turning using 1-inch open-
end wrench.
TA244626
2-1461
TA244626
2-1461
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
55 Bulkhead fitting 45-degree elbow (1) Screw in and tighten using 7/16-inch open-
(2) on engine side end wrench.
of firewall (3) Position elbow toward line.
56 45-degree elbow (1) Line (4) Screw on and tighten using 7/16-inch and
9/16-inch open-end wrenches.
Use care when working behind instrument panel to prevent breaking or disconnecting wires.
58 Bulkhead fitting 90-degree elbow (5) Screw in and tighten using 1/2-inch open-
(3) on driver’s end wrench.
side of firewall (6)
TA244627
2-1462
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
59 90-degree elbow (5) Line (4) Screw on and tighten using 1/2-inch and
9/16-inch open-end wrenches.
62 90-degree elbow (8) Line (4) a Screw on and tighten using two 9116-
inch open-end wrenches.
b Get rid of tag.
TA244628
2-1463
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
TA244629
2-1464
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
FOLLOW-ON MAINTENANCE:
2-1465
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel to prevent breaking or disconnecting wires.
4 a Hold gage.
Two nuts (5) and b Using 3/8-inch open-end wrench, un-
two lockwashers (6) screw and take off.
c Get rid of lockwashers.
5 Take off.
Mounting bracket (7)
2-1466
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTIONIREPLACEMENT
NOTE
TA244631
2-1467
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION
13 Two nuts (4) and two Screw on and tighten using 318-inch open-
new lockwashers (5) end wrench.
16 Adapter (6) Elbow (7) Screw in and tighten using 9/16-inch and
3/4-inch open-end wrenches.
Position as shown.
17 Elbow (7) Line (8) Screw on and tighten using two 9/16-inch
open-end wrenches.
TA244632
2-1468
TM 5-3805-254-20-2
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools
Personnel Required
Piers, diagonal-cutting, 6-inch One
Wrench, open-end, 31/8-inch
Wrench, open-end, 5/8-inch Equipment Condition
Wrench, open-end, 7/8-inch
Materials/Parts Left side cab door opened (page 2-424).
Upper center instrument panel opened
Lockwasher, gage (two required) (page 2-424).
Strap, tiedown (item 20, appendix C) Right and left side hood panels opened
(page 2-424)
Cooling system drained (page 2-628).
2-1469
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
Make sure water temperature gage is not disconnected from line Damage to gage will occur.
TA244633
2-1470
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CAUTION
Use care when performing steps 6 and 7 to prevent damage to water temperature gage and line.
INSPECTION/REPLACEMENT
NOTE
TA244634
2-1471
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
INSTALLATION
CAUTION
Make sure water temperature gage is not disconnected from line Damage to gage will occur.
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
Use care when performing steps 12 and 13 to prevent damage to water temperature gage and line.
TA244635
2-1472
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244636
2-1473
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
NOTE
FOLLOW-ON MAINTENANCE:
TA244637
2-1474
TM 5-3805-254-20-2
INITIAL SETUP
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel to prevent breaking or disconnecting wires.
TA244638
2-1475
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
Line (2) Using two 9116-inch open-end wrenches,
2 Elbow (1) unscrew and take off.
INSPECTION/REPLACEMENT
NOTE
CAUTION
Use care when working behind right instrument panel to prevent breaking or disconnecting wires.
2-1476
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13 Gage (3) Two new lockwashers Screw on and tighten using 3/8-inch open-
(5) and two nuts (4) end wrench.
NOTE
Position elbow so that male threads are pointing toward hinge in instrument panel.
15 Elbow (1) Line (2) Screw on and tighten using two 9/16-inch
open-end wrenches.
TA244639
2-1477
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
Tools One
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
Pull out.
1 Gage (1) Light socket (2)
a Tag (page 2-424).
2 Two adapters (3) Two lines (4) b Using 1/2-inch and 9/16-inch open-
end wrenches, unscrew and take off.
2-1478
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
3 Gage (1) Two adapters (3) Using 1/2-inch and 9/16-inch open-end
wrenches, unscrew and take off.
INSPECTION/REPLACEMENT
NOTE
TA244640
2-1479
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT - CONTINUED
INSTALLATION
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
end wrench.
14 Screw on and tighten using 1/2-inch and
9/16-inch open-end wrenches.
2-1480
TM 5-3805-254-20-2
NOTE
FOLLOW-ON MAINTENANCE:
INITIAL SETUP
Tools Materials/Parts
TA244641
2-1481
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL
CAUTION
Use care when working behind right instrument panel to prevent breaking or disconnecting wires.
TA244642
2-1482
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
TA244643
2-1483
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment Refer to TM 9-247.
NOTE
TA244644
2-1484
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
Particles blown by compressed air are hazardous Make certain the air stream is directed away from user and
other personnel in the area Compressed air used for cleaning purposes shall not exceed 30 psi (207 kPa)
User must wear safety goggles or face shield to prevent injury to personnel.
11 Line (2), fittings Using air blow gun and air hose assembly,
(1 and 5), and blow dry.
coupling (3)
TA244645
2-1485
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEMENT
NOTE
13 Line (1) and Flare seats Look for cracks, bends, or dents.
fittings (2)
INSTALLATION
CAUTION
Antiseizing tape must be used on all pipe threads to provide a good seal and to prevent threaded parts from
seizing.
TA244646
2-1486
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
NOTE
For more information on how to use antiseizing tape, go to General Maintenance Instructions (page 2-
424).
18. Coupling (4) Straight pipe Screw in and tighten using 7/16-inch and
fitting (5) 1/2-inch open-end wrenches.
19. Straight pipe Line (1) Screw on and tighten using 7/16inch and
fitting (5) 9/16-inch open-end wrenches.
TA244647
2-1487
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
Use care when working behind right instrument panel to prevent breaking or disconnecting wires.
TA244648
2-1488
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
27. Elbow (7) Line (2) Screw on and tighten using two 9116-inch
open-end wrenches.
NOTE
FOLLOW-ON MAINTENANCE:
2-1489
TM 5-3805-254-20-2
INITIAL SETUP
Materials/Parts
ACTION
LOCATION ITEM REMARKS
REMOVAL
WARNING
Drain air from air tank system before removing lines or fittings to avoid injury to personnel from
compressed air.
2-1490
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
4. Gage (3) Two adapters (5) Using 1/2-inch and 9/16-inch open-end
wrenches, unscrew and take off.
CAUTION
Use care when performing steps 5, 6, and 7 to prevent damage to air pressure switches, wires, and lines.
TA244651
2-1491
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
REMOVAL - CONTINUED
6. Air manifold (3) Straight pipe Using 9/16-inch open-end wrench, un-
fitting (1) screw and take out.
TA244652
2-1492
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
CLEANING
WARNING
Improper cleaning methods and use of unauthorized cleaning liquids or solvents can injure personnel and
cause damage to equipment. Refer to TM 9-247.
NOTE
For more information on how to clean parts, go to General Maintenance Instructions (page 2-424).
WARNING
Particles blown by compressed air are hazardous. Make certain the air stream is directed away from user
and other personnel in the area. Compressed air used for cleaning purposes shall not exceed 30 psi (207
kPa). User must wear safety goggles or face shield to prevent injury to personnel.
9. Lines (2 and 5) and Using air blow gun and air assembly, blow
fittings (1 and 6) dry.
TA244653
2-1493
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSPECTION/REPLACEM ENT
NOTE
For more information on how to inspect parts, go to General Maintenance Instructions (page 2-424).
11. Lines (1) and Flare seats (3) Look for cracks, dents, or bends.
fittings (2)
12. All threaded parts Look for damaged threads or rounded nuts.
INSTALLATION
CAUTION
Use care when performing steps 13 thru 16 to prevent damage to air pressure switches, wires, and lines.
TA244654
2-1494
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
13. T-fitting (3) Line (4) Screw on and tighten using 7/16-inch and
9/16-inch open-end wrenches.
15. Air manifold (6) Straight pipe Screw in and tighten using 9/16-inch open-
fitting (5) end wrench.
16. Straight pipe Line (7) Screw on and tighten using two 9116-inch
fitting (5) open-end wrenches.
2-1495
TM 5-3805-254-20-2
ACTION
LOCATION ITEM REMARKS
INSTALLATION - CONTINUED
17. Two adapters (1) Wrap pipe threads with antiseizing tape
(page 2-424).
CAUTION
Use care when working behind upper center instrument panel to prevent breaking or disconnecting wires.
18. Gage (2) Two adapters (1) Screw on and tighten using 1/2-inch and
9/16-inch open-end wrenches.
19. Two adapters (1) Two lines (3) a. Screw on and tighten using 112-inch and
9/16inch open-end wrenches.
b. Get rid of tags.
NOTE
FOLLOW-ON MAINTENANCE:
2-1496
TM 5-3805-254-20-2
APPENDIX A
REFERENCES
A-1. SCOPE.
This appendix lists all forms, technical bulletins, technical manuals, and miscellaneous publications referenced in this
manual.
The following indexes should be consulted frequently for latest changes or revisions and for new publications relating to
material covered in this technical manual.
A-3. FORMS.
Change 1 A-1
TM 5-3805-254-20-2
Change 1 A-2
TM 5-3805-254-20-2
APPENDIX B
Section I. INTRODUCTION
B-1. GENERAL.
a. This section provides a general explanation of all maintenance and repair functions authorized at the various
maintenance levels.
b. The Maintenance Allocation Chart (MAC) in Section II designates overall authority and responsibility for the
performance of maintenance functions on the identified end item or component. The application of the maintenance
functions to the end item or component will be consistent with the capacities and capabilities of the designated
maintenance levels.
c. Section III lists the tools and test equipment (both special tools and common tool sets) required for each
maintenance function as referenced from Section II.
d. Section IV contains supplemental instructions and explanatory notes for a particular maintenance function.
a. Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical
characteristics with established standards through examination (e.g., by sight, sound, or feel).
c. Service. Operations required periodically to keep an item in proper operating condition, i.e., to clean
(includes decontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants, chemical fluids, or
gases.
d. Adjust. To maintain or regulate, within prescribed limits, by bringing into proper or exact position, or by
setting the operating characteristics to specified parameters.
e. Aline. To adjust specified variable elements of an item to bring about optimum or desired performance.
g. Remove/Install. To remove and install the same Item when required to perform service or other
maintenance functions. Install may be the act of emplacing, seating, or fixing Into position a spare, repair part, or module
(component or assembly) in a manner to allow the proper functioning of an equipment or system.
h. Replace. To remove an unserviceable item and install a serviceable counterpart in its place. "Replace" is
authorized by the MAC and is shown as the third position of the SMR code.
Change 1 B-1
TM 5-3805-254-20-2
J. Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely service
able/operational condition as required by maintenance standards in appropriate technical publications (I.e., DMWR).
Overhaul Is normally the highest degree of maintenance performed by the Army. Overhaul does not normally return an
item to like new condition.
k. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a
like new condition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel
maintenance applied to Army equipment. The rebuild operation includes the act of returning to zero those age
measurements (hours/miles, etc.) considered in classifying Army equipment/components.
a. Column 1, Group Number. Column 1 lists functional group code numbers, the purpose of which is to
identify maintenance significant components, assemblies, subassemblies, and modules with the next higher assembly.
End item group number shall be "00."
c. Column 3, Maintenance Function. Column 3 lists the functions to be performed on the item listed in Column
2. (For a detailed explanation of these functions, see paragraph C-2.)
d. Column 4, Maintenance Level. Column 4 specifies, by the listing of a work time figure in the appropriate
subcolumn(s), the level of maintenance authorized to perform the function listed in Column 3. This figure represents the
active time required to perform that maintenance function at the indicated level of maintenance. If the number or
complexity of the tasks within the listed maintenance function vary at different maintenance levels, appropriate work time
figures will be shown for each level. The work time figure represents the average time required to restore an item
(assembly, subassembly, component, module, end item, or system) to a serviceable condition under typical field operating
conditions. This time includes preparation time (including any necessary disassembly/assembly time), troubleshooting/
fault location time, and quality assurance/quality control time in addition to the time required to perform the specific tasks
identified for the maintenance functions authorized in the Maintenance Allocation Chart.
The symbol designations for the various maintenance levels are as follows:
e. Column 5, Tools and Equipment. Column 5 specifies, by code, those common tool sets (not individual
tools) and special tools, TMDE, and support equipment required to perform the designated function.
f. Column 6, Remarks. This column shall, when applicable, contain a letter code, in alphabetic order, which
shall be keyed to the remarks contained in Section IV.
B-4. EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS, Section III.
a. Column 1, Tool or Test Equipment Reference Code. The tool and test equipment reference code correlates
with a code used in the MAC, Section II, Column 5.
b. Column 2, Maintenance Level. The lowest level of maintenance authorized to use the tool or test
equipment.
Change 1 B-2
TM 5-3805-254-20-2
B-4. EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS, Section III
CONTINUED.
d. Column 4, National/NATO Stock Number. The National or NATO Stock Number of the tool or test
equipment.
b. Column 2, Remarks. This column lists information pertinent to the maintenance function being performed
as indicated in the MAC, Section II.
01 ENGINE
Change 1 B-3
TM 5-3805-254-20-2
0102 Crankshaft
Crankshaft and Main Replace 6.0 1,4
Bearings Repair 17.3 1,4 B
Main Seals Replace 20.0 1,4
Vibration Damper Replace 1.3 1,4
Crankshaft Groove Pulley Replace 1.0 1,4
Change 1 B-4
TM 5-3805-254-20-2
0108 Manifolds
Intake Replace 2.2 1
Exhaust Replace 2.8 1
Change 1 B-5
TM 5-3805-254-20-2
03 FUEL SYSTEM
Change 1 B-6
TM 5-3805-254-20-2
04 EXHAUST SYSTEM
05 COOLING SYSTEM
Change 1 B-7
TM 5-3805-254-20-2
06 ELECTRICAL SYSTEM
Change 1 B-8
TM 5-3805-254-20-2
0609 Lights
Headlights Inspect 0.1
Adjust 0.3 1
Replace 1.0 1
Tail and Signal Lights Inspect 0.1
Replace 1.0 1
Repair 0.5 1 F
Lamps Replace 0.5 1
Domelight Inspect 0.1
Replace 0.5 1
Change 1 B-9
TM 5-3805-254-20-2
Change 1 B-10
TM 5-3805-254-20-2
07 TRANSMISSION
Change 1 B-11
TM 5-3805-254-20-2
09 PROPELLER, PROPEL-
LER SHAFTS, UNIVER-
SAL JOINTS, COUPLER,
AND CLAMP ASSEM-
BLY
Change 1 B-12
TM 5-3805-254-20-2
10 FRONT AXLE
11 REAR AXLE
1102 Differential
Front and Rear Differential Replace 8.0 1,4
Repair 2.0 1,4
Interaxle Differential Service 0.4 2
Replace 6.5 1,4
Repair 1.5 1,4
Change 1 B-13
TM 5-3805-254-20-2
12 BRAKES
1201 Handbrakes
Parking Brake Housing Replace 4.5 1,2
Change 1 B-14
TM 5-3805-254-20-2
Change 1 B-15
TM 5-3805-254-20-2
14 STEERING
Change 1 B-16
TM 5-3805-254-20-2
1601 Springs
Front Spring Inspect 0.1
Replace 3.0 1,4
Rear Spring Inspect 0.1
Replace 6.0 1,4
Change 1 B-17
TM 5-3805-254-20-2
Change 1 B-18
TM 5-3805-254-20-2
Change 1 B-19
TM 5-3805-254-20-2
Change 1 B-20
TM 5-3805-254-20-2
47 GAGES (NONELECTRI-
CAL), WEIGHING AND
MEASURING DEVICES
4701 Instruments
Change 1 B-21
TM 5-3805-254-20-2
Change 1 B-22
TM 5-3805-254-20-2
REFERENCE REMARKS
CODE
A Inspection limited to visual checks for leaks, fluid levels, loose components, and listening
for unusual noises.
B Overhaul of crankshaft includes metalizing, grinding, and alining.
C Replacement of connecting rod includes alinement.
D Repair limited to removing and installing new gasket.
E Adjust includes rotating adjustment cap.
F Repair of taillights and signal lights limited to lens, gasket, and lamp replacement.
G Item requires special handling or condemnation procedures. Refer to TM 9-6140-200-14 for
lead-acid storage battery procedures.
H Repair of wiring harness limited to terminal and hardware replacement.
I Inspection limited to checking fluid level.
J Refer to TM 9-2610-200-14 for tire and tube repair.
K Repair consists of welding, straightening, and reconditioning the damaged part or parts.
Refer to TB 9-2300-247-40.
APPENDIX C
C-1. SCOPE.
This appendix lists expendable supplies and materials you will need to operate and maintain the F-5070 Dump Truck.
a. Column 1, Item number. This number is assigned to the entry in the listing and is referenced in the narrative
instructions to identify the material.
b. Column 2, Level. This column identifies the lowest level of maintenance that requires the listed item.
C - Operator/Crew
O - Organizational
c. Column 3, National Stock Number. This national stock number is assigned to an item. Use it to request or
requisition the item.
d. Column 4, Description. Indicates Federal item name and a description if necessary. The last line for each item
indicates the Federal Supply Code for Manufacturer (FSCM) in parentheses followed by the part number.
e. Column 5, Unit of Measure (U/M). Indicates measure used in performing actual maintenance functions. This
measure is expressed by a two-character alphabetical abbreviation.
C-1
TM 5-3805-254-20-2
C-2
TM 5-3805-254-20-2
C-3
TM 5-3805-254-20-2
25 O Tape, Masking
28 O Wire, Mechanics
C4
TM 5-3805-254-20-2
APPENDIX D
TORQUE LIMITS
If replacement capscrews are of a higher grade than originally supplied, use torque speci-fications for that placement.
This will prevent equipment damage due to overtorquing.
D-1
TM 5-3805-254-20-2
NOTE
Always use the torque values listed above when specific torque values are not available.
Do not use above values in place of those specified in other sections of this manual; special attention should be observed
when using SAE Grade 6, 7, and 8 capscrews.
Capscrews threaded into aluminum may require reductions in torque of 30 percent or more of Grade 5 capscrews torque
and must attain two capscrew diameters of thread engagement.
D-2
TM 5-3805-254-20-2
INDEX
Subject Page
A
Index-1
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
A - CONTINUED
Change 1 Index-2
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
B - CONTINUED
Index 3
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
B - CONTINUED
Index 4
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
B - CONTINUED
Index 5
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
B - CONTINUED
Cab floor through connector to double check valve hose .................................................................................. 2-1108
Cleaning....................................................................................................................................................... 2-1112
Inspection/Replacement .............................................................................................................................. 2-1112
Installation.................................................................................................................................................... 2-1112
Removal....................................................................................................................................................... 2-1109
Cab roof marker light and clearance light........................................................................................................... 2-801
Inspection/Replacement .............................................................................................................................. 2-804
Installation.................................................................................................................................................... 2-804
Removal....................................................................................................................................................... 2-802
Cable, battery negative....................................................................................................................................... 2-824
Assembly ..................................................................................................................................................... 2-827
Cleaning....................................................................................................................................................... 2-826
Disassembly................................................................................................................................................. 2-826
Inspection/Replacement .............................................................................................................................. 2-827
Installation.................................................................................................................................................... 2-828
Removal....................................................................................................................................................... 2-824
Cable, battery positive........................................................................................................................................ 2-829
Assembly ..................................................................................................................................................... 2-834
Cleaning....................................................................................................................................................... 2-832
Disassembly................................................................................................................................................. 2-832
Inspection/Replacement .............................................................................................................................. 2-833
Installation.................................................................................................................................................... 2-834
Removal....................................................................................................................................................... 2-830
Cable, connector, battery positive-to-negative ................................................................................................... 2-819
Assembly ..................................................................................................................................................... 2-822
Cleaning....................................................................................................................................................... 2-820
Disassembly................................................................................................................................................. 2-820
Inspection/Replacement .............................................................................................................................. 2-822
Installation.................................................................................................................................................... 2-822
Removal....................................................................................................................................................... 2-820
Cable, speedometer drive .................................................................................................................................. 2-1414
Inspection/Replacement .............................................................................................................................. 2-1416
Installation.................................................................................................................................................... 2-1416
Removal....................................................................................................................................................... 2-1414
Cable, tachometer drive ..................................................................................................................................... 2-1420
Inspection/Replacement .............................................................................................................................. 2-1422
Installation.................................................................................................................................................... 2-1422
Removal....................................................................................................................................................... 2-1420
Index 6
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
C - CONTINUED
Change 1 Index-7
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
C - CONTINUED
Change 1 Index 8
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
D - CONTINUED
Double check valve hose, to, cab floor through connector................................................................................. 2-1108
Cleaning....................................................................................................................................................... 2-1112
Inspection/Replacement .............................................................................................................................. 2-1112
Installation.................................................................................................................................................... 2-1112
Removal....................................................................................................................................................... 2-1109
Double check valve hose, to, chassis t-fitting..................................................................................................... 2-1143
Cleaning....................................................................................................................................................... 2-1144
Inspection/Replacement .............................................................................................................................. 2-1144
Installation.................................................................................................................................................... 2-1145
Removal....................................................................................................................................................... 2-1144
Double check valve to double check valve t-fitting hose .................................................................................... 2-1071
Cleaning....................................................................................................................................................... 2-1072
Inspection/Replacement .............................................................................................................................. 2-1072
Installation.................................................................................................................................................... 2-1072
Removal....................................................................................................................................................... 2-1072
INDEX - CONTINUED
Subject Page
D - CONTINUED
Double check valve t-fitting hose, to, brake treadle valve .................................................................................. 2-1062
Cleaning....................................................................................................................................................... 2-1064
Inspection/Replacement .............................................................................................................................. 2-1064
Installation.................................................................................................................................................... 2-1064
Removal....................................................................................................................................................... 2-1062
Double check valve t-fitting to front relay valve t-fitting hose.............................................................................. 2-1149
Cleaning....................................................................................................................................................... 2-1150
Inspection/Replacement .............................................................................................................................. 2-1150
Installation.................................................................................................................................................... 2-1150
Removal....................................................................................................................................................... 2-1149
Draining steering system.................................................................................................................................... 2-1207
Draining........................................................................................................................................................ 2-1208
Driver’s seat........................................................................................................................................................ 2-1274.1
Installation.................................................................................................................................................... 2-1274.2
Removal....................................................................................................................................................... 2-1274.2
Driver’s seat covers and pan.............................................................................................................................. 2-1275
Installation.................................................................................................................................................... 2-1275
Removal....................................................................................................................................................... 2-1275
Dry air reservoir .................................................................................................................................................. 2-975
Assembly ..................................................................................................................................................... 2-982
Cleaning....................................................................................................................................................... 2-980
Disassembly................................................................................................................................................. 2-978
Inspection/Replacement .............................................................................................................................. 2-980
Installation.................................................................................................................................................... 2-984
Removal....................................................................................................................................................... 2-976
Dry air reservoir to front relay valve hose........................................................................................................... 2-1080
Cleaning....................................................................................................................................................... 2-1082
Inspection/Replacement .............................................................................................................................. 2-1082
Installation.................................................................................................................................................... 2-1083
Removal....................................................................................................................................................... 2-1081
Dry air reservoir to t-manifold hoses .................................................................................................................. 2-1074
Cleaning....................................................................................................................................................... 2-1075
Inspection/Replacement .............................................................................................................................. 2-1075
Installation.................................................................................................................................................... 2-1076
Removal....................................................................................................................................................... 2-1074
Dry air reservoir to wet air reservoir hoses......................................................................................................... 2-1077.2
Cleaning....................................................................................................................................................... 2-1078
Inspection/Replacement .............................................................................................................................. 2-1078
Installation.................................................................................................................................................... 2-1079
Removal....................................................................................................................................................... 2-1078
Dryer, air............................................................................................................................................................. 2-1002
Assembly ..................................................................................................................................................... 2-1009
Cleaning....................................................................................................................................................... 2-1006
Disassembly................................................................................................................................................. 2-1004
Inspection/Replacement .............................................................................................................................. 2-1008
Installation.................................................................................................................................................... 2-1012
Removal....................................................................................................................................................... 2-1002
Dump body maintenance ................................................................................................................................... 2-1251
Change 1 Index 9
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
D - CONTINUED
Change 1 Index 10
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
E - CONTINUED
Index 11
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
F - CONTINUED
Change 1 Index 12
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
F - CONTINUED
Front brake limiting and quick release valve hoses, to, right front
wheel ............................................................................................................................................................. 2-1122
Cleaning....................................................................................................................................................... 2-1126
Inspection/Replacement .............................................................................................................................. 2-1126
Installation.................................................................................................................................................... 2-1126
Removal....................................................................................................................................................... 2-1122
Front brake limiting and quick release valve to brake treadle valve
hose............................................................................................................................................................... 2-1084
Cleaning....................................................................................................................................................... 2-1086
Inspection/Replacement .............................................................................................................................. 2-1086
Installation.................................................................................................................................................... 2-1087
Removal....................................................................................................................................................... 2-1085
Front brake limiting control valve hoses and fittings........................................................................................... 2-1159
Cleaning....................................................................................................................................................... 2-1162
Inspection/Replacement .............................................................................................................................. 2-1163
Installation.................................................................................................................................................... 2-1164
Removal....................................................................................................................................................... 2-1160
Front brakes ....................................................................................................................................................... 2-947
Adjustment ................................................................................................................................................... 2-954
Cleaning....................................................................................................................................................... 2-950
Inspection/Replacement .............................................................................................................................. 2-950
Installation.................................................................................................................................................... 2-952
Removal....................................................................................................................................................... 2-948
Front fender reflectors ........................................................................................................................................ 2-1320
Installation.................................................................................................................................................... 2-1320
Removal....................................................................................................................................................... 2-1320
Front hub and brakedrum assembly and wheel bearings .................................................................................. 2-1175
Assembly ..................................................................................................................................................... 2-1184
Cleaning....................................................................................................................................................... 2-1178
Disassembly................................................................................................................................................. 2-1178
Inspection/Replacement .............................................................................................................................. 2-1180
Installation.................................................................................................................................................... 2-1184
Removal....................................................................................................................................................... 2-1176
Front marker light ............................................................................................................................................... 2-799
Inspection/Replacement .............................................................................................................................. 2-800
Installation.................................................................................................................................................... 2-801
Removal....................................................................................................................................................... 2-800
Front rear of cab junction box............................................................................................................................. 2-780
Inspection/Replacement .............................................................................................................................. 2-782
Installation.................................................................................................................................................... 2-782
Removal....................................................................................................................................................... 2-780
Front rear quick release valve ............................................................................................................................ 2-1088.1
Installation.................................................................................................................................................... 2-1088.2
Removal....................................................................................................................................................... 2-1088.2
Front rear quick release valve hose, to, chassis t-fitting .................................................................................... 2-1146
Cleaning....................................................................................................................................................... 2-1146
Inspection/Replacement .............................................................................................................................. 2-1147
Installation.................................................................................................................................................... 2-1148
Removal....................................................................................................................................................... 2-1146
Change 1 Index 13
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
F - CONTINUED
Front rear quick release valve to parking airbrake chamber hoses ................................................................... 2-1088.3
Cleaning....................................................................................................................................................... 2-1090
Inspection/Replacement .............................................................................................................................. 2-1091
Installation.................................................................................................................................................... 2-1092
Removal....................................................................................................................................................... 2-1089
Front rear t-fitting ................................................................................................................................................ 2-1093.0
Installation.................................................................................................................................................... 2-1093.0
Removal....................................................................................................................................................... 2-1093.0
Front rear t-fitting hose, to, front relay valve....................................................................................................... 2-1099
Cleaning....................................................................................................................................................... 2-1100
Inspection/Replacement .............................................................................................................................. 2-1100
Installation.................................................................................................................................................... 2-1100
Removal....................................................................................................................................................... 2-1099
Front rear t-fitting to service air brake chamber hoses....................................................................................... 2-1093.1
Cleaning....................................................................................................................................................... 2-1096
Inspection/Replacement .............................................................................................................................. 2-1096
Installation.................................................................................................................................................... 2-1096
Removal....................................................................................................................................................... 2-1094
Front relay valve ................................................................................................................................................. 2-1098.1
Installation.................................................................................................................................................... 2-1098.2
Removal....................................................................................................................................................... 2-1098.2
Front relay valve t-fitting hose, to, double check valve t-fitting........................................................................... 2-1149
Cleaning....................................................................................................................................................... 2-1150
Inspection/Replacement .............................................................................................................................. 2-1150
Installation.................................................................................................................................................... 2-1150
Removal....................................................................................................................................................... 2-1149
Front relay valve t-fitting to rear relay valve hose............................................................................................... 2-1105
Cleaning....................................................................................................................................................... 2-1106
Inspection/Replacement .............................................................................................................................. 2-1106
Installation.................................................................................................................................................... 2-1107
Removal....................................................................................................................................................... 2-1105
Front relay valve to front rear t-fitting hose......................................................................................................... 2-1099
Cleaning....................................................................................................................................................... 2-1100
Inspection/Replacement .............................................................................................................................. 2-1100
Installation.................................................................................................................................................... 2-1100
Removal....................................................................................................................................................... 2-1099
Front relay valve to rear relay valve hose........................................................................................................... 2-1101
Cleaning....................................................................................................................................................... 2-1102
Inspection/Replacement .............................................................................................................................. 2-1103
Installation.................................................................................................................................................... 2-1103
Removal....................................................................................................................................................... 2-1102
Front turn signal.................................................................................................................................................. 2-795
Assembly ..................................................................................................................................................... 2-797
Disassembly................................................................................................................................................. 2-796
Inspection/Replacement .............................................................................................................................. 2-796
Installation.................................................................................................................................................... 2-799
Removal....................................................................................................................................................... 2-795
Front wheel......................................................................................................................................................... 2-1168
Disassembly/Repair/Assembly .................................................................................................................... 2-1169
Installation.................................................................................................................................................... 2-1169
Removal....................................................................................................................................................... 2-1168
Change 1 Index 14
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
F - CONTINUED
Index 15
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
G - CONTINUED
Change 1 Index 16
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
H - CONTINUED
Index 17
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
H - CONTINUED
Hose, t-fitting, double check valve, to, double check valve ................................................................................ 2-1071
Cleaning....................................................................................................................................................... 2-1072
Inspection/Replacement .............................................................................................................................. 2-1072
Installation.................................................................................................................................................... 2-1072
Removal....................................................................................................................................................... 2-1072
Hoses and fittings, front brake limiting control valve .......................................................................................... 2-1159
Cleani ng...................................................................................................................................................... 2-1162
Inspection/Replacement .............................................................................................................................. 2-1163
Installation.................................................................................................................................................... 2-1164
Removal....................................................................................................................................................... 2-1160
Hoses, tubes, and fittings, power divider............................................................................................................ 2-946.1
Inspection/Replacement .............................................................................................................................. 2-946.5
Installation.................................................................................................................................................... 2-946.6
Removal....................................................................................................................................................... 2-946.2
Hoses, right manifold, and brake treadle valve .................................................................................................. 2-1052
Cleani ng...................................................................................................................................................... 2-1056
Inspection/Replacement .............................................................................................................................. 2-1056
Installlation ................................................................................................................................................... 2-1057
Removal....................................................................................................................................................... 2-1052
Hoses, t-manifold, to, brake treadle valve .......................................................................................................... 2-1067
Cleaning....................................................................................................................................................... 2-1068
Inspection/Replacement .............................................................................................................................. 2-1069
Installation.................................................................................................................................................... 2-1070
Removal....................................................................................................................................................... 2-1068
Hoses, t-manifold, to, dry air reservoir ............................................................................................................... 2-1074
Cleaning....................................................................................................................................................... 2-1075
Inspection/Replacement .............................................................................................................................. 2-1075
Installation.................................................................................................................................................... 2-1076
Removal....................................................................................................................................................... 2-1074
Hoses, wet air reservoir, to, dry air reservoir...................................................................................................... 2-1077.2
Cleaning....................................................................................................................................................... 2-1078
Inspection/Replacement .............................................................................................................................. 2-1078
Installation.................................................................................................................................................... 2-1079
Removal....................................................................................................................................................... 2-1078
Housing, and, hydraulic filter .............................................................................................................................. 2-1362
Cleaning....................................................................................................................................................... 2-1364
Inspection/Replacement .............................................................................................................................. 2-1364
Installation.................................................................................................................................................... 2-1365
Removal....................................................................................................................................................... 2-1362
Housing, rear axle .............................................................................................................................................. 2-942
Draining........................................................................................................................................................ 2-943
Filling............................................................................................................................................................ 2-944
Oil level check.............................................................................................................................................. 2-942
How to use this manual ...................................................................................................................................... ii
Hydraulic filter and housing ................................................................................................................................ 2-1362
Cleaning....................................................................................................................................................... 2-1364
Inspection/Replacement .............................................................................................................................. 2-1364
Installation.................................................................................................................................................... 2-1365
Removal....................................................................................................................................................... 2-1362
Hydraulic oil reservoir ......................................................................................................................................... 2-1375
Assembly ..................................................................................................................................................... 2-1380
Cleaning....................................................................................................................................................... 2-1378
Change 1 Index 18
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
H - CONTINUED
Disassembly................................................................................................................................................. 2-1377
Inspection/Replacement .............................................................................................................................. 2-1380
Installation.................................................................................................................................................... 2-1383
Removal....................................................................................................................................................... 2-1376
Installation
Airbrake cylinder control valve ..................................................................................................................... 2-1034.2
Air cleaner vacuum gage ............................................................................................................................. 2-1468
Air cleaner vacuum gage line and fittings .................................................................................................... 2-1486
Air compressor governor to wet air reservoir lines and fitting...................................................................... 2-1050
Air compressor to air dryer hose and lines .................................................................................................. 2-1038
Air dryer........................................................................................................................................................ 2-1012
Air dryer cartridge ........................................................................................................................................ 2-1020
Air horn ........................................................................................................................................................ 2-1348
Air pressure gage......................................................................................................................................... 2-1480
Air pressure gage lines and fittings.............................................................................................................. 2-1486
Alarm bell ..................................................................................................................................................... 2-718
Alcohol evaporator ....................................................................................................................................... 2-1001
Ammeter ...................................................................................................................................................... 2-732
Automatic override module .......................................................................................................................... 2-878
Backup light 20 amp circuit breaker............................................................................................................. 2-751
Backup light switch ...................................................................................................................................... 2-690
Battery box................................................................................................................................................... 2-855
Battery negative cable.................................................................................................................................. 2-828
Battery positive cable................................................................................................................................... 2-834
Battery positive-to-negative connector cable............................................................................................... 2-822
Brake pedal.................................................................................................................................................. 2-1024
Brake treadle valve and right manifold hoses.............................................................................................. 2-1057
Brake treadle valve to double check valve t-fitting hose.............................................................................. 2-1064
Brake treadle valve to t-manifold hoses....................................................................................................... 2-1070
Change 1 Index 19
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
I - CONTINUED
Installation - Continued
Cab floor through connector to double check valve hose............................................................................ 2-1112
Cab roof marker light and clearance light .................................................................................................... 2-804
Center engine side of firewall junction box .................................................................................................. 2-773
Chassis 90-degree elbow ............................................................................................................................ 2-1151.0
Chassis 90-degree elbow to rear rear quick release valve hose ................................................................. 2-1158
Chassis t-fitting ............................................................................................................................................ 2-1151.2
Chassis t-fitting to chassis 90-degree elbow hose....................................................................................... 2-1153
Chassis t-fitting to double check valve hose................................................................................................ 2-1145
Chassis t-fitting to front rear quick release valve hose ................................................................................ 2-1148
Data and instruction plates .......................................................................................................................... 2-1353
Dome light.................................................................................................................................................... 2-721
Dome/panel lamp switch.............................................................................................................................. 2-724
Double check valve...................................................................................................................................... 2-1148.2
Double check valve t-fitting to front relay valve t-fitting hose....................................................................... 2-1150
INDEX - CONTINUED
Subject Page
I - CONTINUED
Installation - Continued
Double check valve to double check valve t-fitting hose ............................................................................. 2-1072
Driver’s seat ................................................................................................................................................. 2-1274.2
Driver’s seat covers and pan ....................................................................................................................... 2-1275
Dry air reservoir ........................................................................................................................................... 2-984
Dry air reservoir to front relay valve hose .................................................................................................... 2-1083
Dry air reservoir to t-manifold hoses ............................................................................................................ 2-1076
Dry air reservoir to wet air reservoir hoses .................................................................................................. 2-1079
Dump body control lever and linkage........................................................................................................... 2-1370
Dump body marker light............................................................................................................................... 2-806
Dump body reflectors................................................................................................................................... 2-1323
Engine compression brake 15 amp circuit breaker ..................................................................................... 2-749
Engine compression brake switch ............................................................................................................... 2-736
Engine compression brake pressure switch ................................................................................................ 2-684
Engine compression brake throttle switch ................................................................................................... 2-696
Change 1 Index 20
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
I - CONTINUED
Installation - Continued
Front relay valve........................................................................................................................................... 2-1098.2
Front relay valve t-fitting to rear relay valve hose ........................................................................................ 2-1107
Front relay valve to front rear t-fitting hose .................................................................................................. 2-1100
Front relay valve to rear relay valve hose.................................................................................................... 2-1103
Front turn signal ........................................................................................................................................... 2-799
Front wheel .................................................................................................................................................. 2-1169
Fuel gage ..................................................................................................................................................... 2-729
Fuel pressure gage ...................................................................................................................................... 2-1476
Fuse block.................................................................................................................................................... 2-768
Generator and regulator............................................................................................................................... 2-668
Generator drive belts ................................................................................................................................... 2-666
Generator pulley........................................................................................................................................... 2-673
Glow plug and cigar lighter 40 amp circuit breaker...................................................................................... 2-757
Glow plug switch .......................................................................................................................................... 2-734
Headlight assembly...................................................................................................................................... 2-810
INDEX - CONTINUED
Subject Page
I - CONTINUED
Installation - Continued
Headlight beam selector switch ................................................................................................................... 2-743
Headlight 20 amp circuit breaker ................................................................................................................. 2-763
Heater 40 amp circuit breaker ..................................................................................................................... 2-753
Hood ............................................................................................................................................................ 2-1260
Horn ............................................................................................................................................................. 2-716
Horn button .................................................................................................................................................. 2-714
Horn relay..................................................................................................................................................... 2-708
Horn 20 amp circuit breaker ........................................................................................................................ 2-755
Hydraulic filter and housing.......................................................................................................................... 2-1365
Hydraulic oil reservoir................................................................................................................................... 2-1383
Ign system starter circuit breaker................................................................................................................. 2-770
Internal oil filter............................................................................................................................................. 2-908
Key switch.................................................................................................................................................... 2-741
Left brakelight switch ................................................................................................................................... 2-680
Left engine side of firewall junction box ....................................................................................................... 2-778
Left front wheel to front brake limiting and quick release valve
hoses ..................................................................................................................................................... 2-1118
Left instrument panel optical ribbon ............................................................................................................. 2-870
Left side lower instrument panel indicator lamp........................................................................................... 2-886
Left steering gear-to-right steering gear hose and fittings ........................................................................... 2-1218
Left steering gear-to-resevoir hose and fittings ........................................................................................... 2-1214
Left taillight................................................................................................................................................... 2-790
Lights switch ................................................................................................................................................ 2-726
Low air-pressure warning buzzer................................................................................................................. 2-710
Low air-pressure warning buzzer switch...................................................................................................... 2-700
Low air-pressure warning light switch .......................................................................................................... 2-698
Lower center instrument panel gage lamps................................................................................................. 2-887
Lower instrument panel optical ribbon ......................................................................................................... 2-866
Marker light 30 amp circuit breaker ............................................................................................................. 2-765
Neutral safety switch.................................................................................................................................... 2-692
Oil filler tube and dipstick ............................................................................................................................. 2-930
Oil reservoir.................................................................................................................................................. 2-1241.0
Optical light assembly .................................................................................................................................. 2-859
Optical light lamp ......................................................................................................................................... 2-857
Parking brake control valve.......................................................................................................................... 2-1024.2
Passenger seat ............................................................................................................................................ 2-1274
Pintle hook ................................................................................................................................................... 2-1249
Pioneer tool rack .......................................................................................................................................... 2-1284.2
Power divider hoses, tubes, and fittings ...................................................................................................... 2-946.6
Power take-off light switch ........................................................................................................................... 2-694
Power take-off (PTO) indicator lamp ........................................................................................................... 2-880
Change 1 Index 21
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
I - CONTINUED
Installation - Continued
Primary magnetic switch .............................................................................................................................. 2-702
Pump by-pass hose and fitting..................................................................................................................... 2-1235
Pump-to-left steering gear hose and fittings ................................................................................................ 2-1230
Pump-to-valve pressure hose and fittings ................................................................................................... 2-1388
Radiator grille............................................................................................................................................... 2-1284.4
Rear axle housing breather.......................................................................................................................... 2-941
Rear brakes ................................................................................................................................................. 2-965
Rear hub and brake drum assembly and wheel bearings ........................................................................... 2-1198
Rear rear of cab junction box....................................................................................................................... 2-786
Rear rear quick release valve ...................................................................................................................... 2-1130.2
Rear rear quick release valve to parking airbrake chamber hoses ............................................................. 2-1134
Rear relay valve ........................................................................................................................................... 2-1140.2
Rear relay valve to rear rear quick release valve hose................................................................................ 2-1142
INDEX - CONTINUED
Subject Page
I - CONTINUED
Index 23
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
L - CONTINUED
Index 24
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
L - CONTINUED
Index 25
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
Index 26
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
Change 1 Index-27
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
P - CONTINUED
INDEX - CONTINUED
Subject Page
R - CONTINUED
Change 1 Index 29
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
P - CONTINUED
INDEX - CONTINUED
Subject Page
R - CONTINUED
Change 1 Index 31
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
R - CONTINUED
Removal - Continued
Front turn signal ........................................................................................................................................... 2-795
Front wheel .................................................................................................................................................. 2-1168
Fuel gage ..................................................................................................................................................... 2-728
Fuel pressure gage ...................................................................................................................................... 2-1475
Fuse block.................................................................................................................................................... 2-766
Generator and regulator............................................................................................................................... 2-668
Generator drive belts ................................................................................................................................... 2-665
Generator pulley........................................................................................................................................... 2-671
Glow plug and cigar lighter 40 amp circuit breaker...................................................................................... 2-756
Glow plug switch .......................................................................................................................................... 2-734
Headlight assembly...................................................................................................................................... 2-808
Headlight beam selector switch ................................................................................................................... 2-742
Headlight 20 amp circuit breaker ................................................................................................................. 2-762
Heater 40 amp circuit breaker ..................................................................................................................... 2-752
Hood ............................................................................................................................................................ 2-1252
Horn ............................................................................................................................................................. 2-716
Horn button .................................................................................................................................................. 2-714
Horn relay..................................................................................................................................................... 2-708
Horn 20 amp circuit breaker ........................................................................................................................ 2-754
INDEX - CONTINUED
Subject Page
R - CONTINUED
Removal - Continued
Hydraulic filter and housing.......................................................................................................................... 2-1362
Hydraulic oil reservoir................................................................................................................................... 2-1376
Ign system starter circuit breaker................................................................................................................. 2-770
Internal oil filter............................................................................................................................................. 2-908
Key switch.................................................................................................................................................... 2-740
Left brake light switch .................................................................................................................................. 2-680
Left engine side of firewall junction box ....................................................................................................... 2-778
Left front wheel to front brake limiting and quick release valve
hoses ..................................................................................................................................................... 2-1115
Left instrument panel optical ribbon ............................................................................................................. 2-868
Left side lower instrument panel indicator lamp........................................................................................... 2-886
Left steering gear-to-right steering gear hose and fittings ........................................................................... 2-1216
Left steering gear-to-reservoir hose and fittings .......................................................................................... 2-1212
Left taillight................................................................................................................................................... 2-788
Lights switch ................................................................................................................................................ 2-726
Low air-pressure warning buzzer................................................................................................................. 2-710
Low air-pressure warning buzzer switch...................................................................................................... 2-700
Low air-pressure warning light switch .......................................................................................................... 2-698
Lower center instrument panel gage lamps................................................................................................. 2-887
Lower instrument panel optical ribbon ......................................................................................................... 2-864
Marker light 30-amp circuit breaker ............................................................................................................. 2-764
Neutral safety switch.................................................................................................................................... 2-691
Oil filter tube and dipstick............................................................................................................................. 2-928
Oil reservoir.................................................................................................................................................. 2-1238
Optical light assembly .................................................................................................................................. 2-858
Optical light lamp ......................................................................................................................................... 2-857
Parking brake control valve.......................................................................................................................... 2-1024.1
Passenger seat ............................................................................................................................................ 2-1272
Pintle hook ................................................................................................................................................... 2-1248
Pioneer tool rack .......................................................................................................................................... 2-1284.1
Power divider hoses, tubes, and fittings ...................................................................................................... 2-946.2
Power take-off light switch ........................................................................................................................... 2-693
Power take-off (PTO) indicator lamp ........................................................................................................... 2-880
Primary magnetic switch .............................................................................................................................. 2-702
Pump by-pass hose and fitting..................................................................................................................... 2-1232
Pump-to-left steering gear hose and fittings ................................................................................................ 2-1228
Pump-to-valve pressure hose and fittings ................................................................................................... 2-1386
Radiator grille............................................................................................................................................... 2-1284.3
Rear axle housing breather.......................................................................................................................... 2-940
Change 1 Index 32
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
R - CONTINUED
Removal - Continued
Rear brakes ................................................................................................................................................. 2-956
Rear hub and brake drum assembly and wheel bearings ........................................................................... 2-1188
Rear rear of cab junction box....................................................................................................................... 2-784
Rear rear quick release valve ...................................................................................................................... 2-1130.1
Rear rear quick release valve to parking airbrake chamber hoses ............................................................. 2-1132
Rear relay valve ........................................................................................................................................... 2-1140.2
Rear relay valve to rear rear quick release valve hose................................................................................ 2-1141
Rear view mirror assembly .......................................................................................................................... 2-1291
Rear wheel................................................................................................................................................... 2-1171
Remote oil filter cartridge ............................................................................................................................. 2-936
Reservoir-to-pump hose and fittings ............................................................................................................ 2-1224
Reservoir-to-pump suction hose and fittings ............................................................................................... 2-1390
Right brake light switch ................................................................................................................................ 2-682
Right engine side of firewall junction box..................................................................................................... 2-774
INDEX - CONTINUED
Subject Page
R - CONTINUED
Removal - Continued
Right front wheel to front brake limiting and quick release valve
hoses ..................................................................................................................................................... 2-1122
Right instrument panel gage lamps ............................................................................................................. 2-890
Right instrument panel indicator lamps........................................................................................................ 2-892
Right instrument panel optical ribbon........................................................................................................... 2-860
Right steering gear-to-left steering gear hose and fittings ........................................................................... 2-1220
Right taillight................................................................................................................................................. 2-792
Seat belts ..................................................................................................................................................... 2-1282
Secondary magnetic switch ......................................................................................................................... 2-704
Slave receptacle .......................................................................................................................................... 2-895.0
Speedometer ............................................................................................................................................... 2-1408
Speedometer drive cable ............................................................................................................................. 2-1414
Splash guards .............................................................................................................................................. 2-1280
Stop and dome light 30 amp circuit breaker ................................................................................................ 2-758
Storage batteries.......................................................................................................................................... 2-839
Starter motor ................................................................................................................................................ 2-896
T-manifold .................................................................................................................................................... 2-1077.0
Tachometer.................................................................................................................................................. 2-1412
Tachometer drive cable ............................................................................................................................... 2-1420
Tail and panel light 20 amp circuit breaker .................................................................................................. 2-760
Transmission oil pan .................................................................................................................................... 2-902
Transmission oil pressure gage ................................................................................................................... 2-1448
Transmission oil pressure gage line and fittings.......................................................................................... 2-1450
Transmission oil pressure switch ................................................................................................................. 2-678
Transmission oil temperature sender .......................................................................................................... 2-685
Transmission oil temperature switch ........................................................................................................... 2-687
Transmission position indicator lamp........................................................................................................... 2-894
Transmission shift cable .............................................................................................................................. 2-920
Transmission shift control ............................................................................................................................ 2-910
Transmission shift control stand .................................................................................................................. 2-917
Turn signal and hazard flashers................................................................................................................... 2-712
Turn signal indicator lamps .......................................................................................................................... 2-888
Turn signal switch ........................................................................................................................................ 2-744
Upper instrument panel indicator lamps ...................................................................................................... 2-883
Upper instrument panel gage lamps ............................................................................................................ 2-882
Upper instrument panel optical ribbon ......................................................................................................... 2-872
Change 1 Index 33
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
R - CONTINUED
Removal - Continued
Valve-to-cylinder pressure hose and fittings................................................................................................ 2-1400
Valve-to-reservoir return hose and fittings................................................................................................... 2-1396
Water temperature gage and line ................................................................................................................ 2-1470
Wet air reservoir .......................................................................................................................................... 2-986
Wet air reservoir to air dryer hose ............................................................................................................... 2-1154
Windshield washer reservoir and pump....................................................................................................... 2-1344.1
Windshield wiper blade ................................................................................................................................ 2-1300
Windshield wiper control .............................................................................................................................. 2-1338
Windshield wiper motor ............................................................................................................................... 2-1324
Wiper blade and arm ................................................................................................................................... 2-1301
Reporting errors and recommending improvements .......................................................................................... i
Reservoir, dry air ................................................................................................................................................ 2-975
Assembly ..................................................................................................................................................... 2-982
Cleaning....................................................................................................................................................... 2-980
Disassembly................................................................................................................................................. 2-978
Index 34
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
R - CONTINUED
Change 1 Index 35
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
S - CONTINUED
Secondary magnetic switch................................................................................................................................ 2-703
Installation.................................................................................................................................................... 2-704
Removal....................................................................................................................................................... 2-704
Sender, temperature, transmission oil................................................................................................................ 2-685
Installation.................................................................................................................................................... 2-686
Removal....................................................................................................................................................... 2-685
Service airbrake chamber hoses, to, front rear t-fitting ...................................................................................... 2-1093.1
Cleaning....................................................................................................................................................... 2-1096
Inspection/Replacement .............................................................................................................................. 2-1096
Installation.................................................................................................................................................... 2-1096
Removal....................................................................................................................................................... 2-1094
Service airbrake chamber hoses, to, rear rear quick release valve ................................................................... 2-1136
Cleaning....................................................................................................................................................... 2-1138
Inspection/Replacement .............................................................................................................................. 2-1138
Installation.................................................................................................................................................... 2-1138
Removal....................................................................................................................................................... 2-1136
Signal, front turn ................................................................................................................................................. 2-795
Assembly ..................................................................................................................................................... 2-797
Disassembly................................................................................................................................................. 2-796
Inspection/Replacement .............................................................................................................................. 2-796
Installation.................................................................................................................................................... 2-799
Removal....................................................................................................................................................... 2-795
Slave receptacle ................................................................................................................................................. 2-895.0
Cleaning....................................................................................................................................................... 2-895.0
Installation.................................................................................................................................................... 2-895.2
Removal....................................................................................................................................................... 2-895.0
Speedometer ...................................................................................................................................................... 2-1408
Inspection/Replacement .............................................................................................................................. 2-1410
Installation.................................................................................................................................................... 2-1410
Removal....................................................................................................................................................... 2-1408
Speedometer drive cable ................................................................................................................................... 2-1414
Inspection/Replacement .............................................................................................................................. 2-1416
Installation.................................................................................................................................................... 2-1416
Removal....................................................................................................................................................... 2-1414
Splash guards..................................................................................................................................................... 2-1280
Installation.................................................................................................................................................... 2-1280
Removal....................................................................................................................................................... 2-1280
Starter motor ...................................................................................................................................................... 2-896
Installation.................................................................................................................................................... 2-898
Removal....................................................................................................................................................... 2-896
Steering system maintenance ............................................................................................................................ 2-1202
Steering system, filling........................................................................................................................................ 2-1243
Filling............................................................................................................................................................ 2-1243
Stop and dome light 30 amp circuit breaker....................................................................................................... 2-758
Installation.................................................................................................................................................... 2-759
Removal....................................................................................................................................................... 2-758
Storage batteries ................................................................................................................................................ 2-838
Cleaning....................................................................................................................................................... 2-840
Inspection/Replacement .............................................................................................................................. 2-840
Installation.................................................................................................................................................... 2-841
Removal....................................................................................................................................................... 2-839
Testing 2-838
Change 1 Index 36
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
S - CONTINUED
Index 37
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
S - CONTINUED
Change 1 Index-38
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
T - CONTINUED
Index 39
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
T - CONTINUED
Index 40
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
V - CONTINUED
Valve-to-reservoir return hose and fittings ......................................................................................................... 2-1395
Cleaning....................................................................................................................................................... 2-1396
Inspection/Replacement .............................................................................................................................. 2-1398
Installation.................................................................................................................................................... 2-1398
Removal....................................................................................................................................................... 2-1396
W
Warnings ............................................................................................................................................................ a
Water temperature gage and line....................................................................................................................... 2-1469
Inspection/Replacement .............................................................................................................................. 2-1471
Installation.................................................................................................................................................... 2-1472
Removal....................................................................................................................................................... 2-1470
Wet air reservoir ................................................................................................................................................. 2-986
Assembly ..................................................................................................................................................... 2-991
Cleaning....................................................................................................................................................... 2-988
Disassembly................................................................................................................................................. 2-988
Inspection/Replacement .............................................................................................................................. 2-990
Installation.................................................................................................................................................... 2-994
Removal....................................................................................................................................................... 2-986
Wet air reservoir to air dryer hose ...................................................................................................................... 2-1154
Cleaning....................................................................................................................................................... 2-1154
Inspection/Replacement .............................................................................................................................. 2-1155
Installation.................................................................................................................................................... 2-1156
Removal....................................................................................................................................................... 2-1154
Wheel bearings, and, front hub and brakedrum assembly ................................................................................ 2-1175
Assembly ..................................................................................................................................................... 2-1184
Cleaning....................................................................................................................................................... 2-1178
Disassembly................................................................................................................................................. 2-1178
Inspection/Replacement .............................................................................................................................. 2-1180
Installation.................................................................................................................................................... 2-1184
Removal....................................................................................................................................................... 2-1176
Wheel bearings, and, rear hub and brakedrum assembly ................................................................................. 2-1188
Assembly ..................................................................................................................................................... 2-1198
Cleaning....................................................................................................................................................... 2-1192
Disassembly................................................................................................................................................. 2-1191
Inspection/Replacement .............................................................................................................................. 2-1192
Installation.................................................................................................................................................... 2-1198
Removal....................................................................................................................................................... 2-1188
Wheel, front ............................................................................................................................................. 2-1168 2-1168
Disassembly/Repair/Assembly .................................................................................................................... 2-1169
Installation.................................................................................................................................................... 2-1169
Removal....................................................................................................................................................... 2-1168
Wheel, rear ......................................................................................................................................................... 2-1171
Disassembly/Repair/Assembly .................................................................................................................... 2-1172
Installation.................................................................................................................................................... 2-1173
Removal....................................................................................................................................................... 2-1171
Wheel, tire, hub and drum maintenance ............................................................................................................ 2-1168
Windshield washer reservoir and pump ............................................................................................................. 2-1344.1
Installation.................................................................................................................................................... 2-1344.2
Removal....................................................................................................................................................... 2-1344.1
Change 1 Index-41
TM 5-3805-254-20-2
INDEX - CONTINUED
Subject Page
W - CONTINUED
Index-42
By Order of the Secretary of the Army:
CARL E. VUONO
General, United States Army
Chief of Staff
Official:
R.L. DILWORTH
Brigadier General, United States Army
The Adjutant General
Distribution:
To be distributed in accordance with DA Form 12-25A, Unit Maintenance requirements for Truck, Dump, 20T, 6x4
On-Off Highway, 71,000 GVW, Model F5070 (CCE)