Yamaha RX-V661 Navodila
Yamaha RX-V661 Navodila
RX-V661
AV Receiver Ampli-tuner audio-vido
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by MASTER ON/OFF. In this state, this unit is designed to consume a very small quantity of power.
This symbol mark is according to the EU directive 2002/96/EC. This symbol mark means that electrical and electronic equipment, at their endof-life, should be disposed of separately from your household waste. Please act according to your local rules and do not dispose of your old products with your normal household waste.
En
Contents
INTRODUCTION INTRODUCTION
Notice ....................................................................... 2 Features ................................................................... 3
Supplied accessories .................................................. 3
ADVANCED OPERATION
Advanced sound configurations...........................59
Changing sound field parameter settings................. 59 Selecting decoders ................................................... 64
PREPARATION
Connections ........................................................... 11 Optimizing the speaker setting for your listening room ................................................................... 28
Using AUTO SETUP .............................................. 28
PREPARATION
BASIC OPERATION
Selecting the SCENE templates........................... 33
Selecting the desired SCENE template.................... 33 Creating your original SCENE templates................ 36
BASIC OPERATION
Playback ................................................................ 37
Basic procedure ....................................................... 37 Selecting the MULTI CH INPUT component......... 38 Selecting the front speaker set ................................. 38 Selecting audio input jacks (AUDIO SELECT).............................................. 39 Displaying the current status of this unit on a video monitor ................................................................ 39 Using your headphones............................................ 40 Muting the audio output........................................... 40 Playing video sources in the background of an audio source................................................................... 40 Displaying the input source information ................. 40 Using the sleep timer ............................................... 41
Advanced setup......................................................98
Using the advanced setup ........................................ 98
ADDITIONAL INFORMATION
Troubleshooting...................................................102 Resetting the system............................................109 Glossary................................................................110 Sound field program information......................112 Parametric equalizer information .....................113 Specifications .......................................................114 Index .....................................................................116
ADVANCED OPERATION
ADDITIONAL INFORMATION
APPENDIX
Using iPod.......................................................... 56
Controlling iPod................................................... 56
1 SPEAKERS or A DVD (example) indicates the name of the parts on the front panel or the remote control. Refer to the attached sheet or the pages at the end of this manual for the information about each position of the parts.
English
Recording .............................................................. 58
1 En
NOTICE
Notice
About this manual
y indicates a tip for your operation. Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses. This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority. 1 SPEAKERS or A DVD (example) indicates the name of the parts on the front panel or the remote control. Refer to the attached sheet or the pages at the end of this manual for the information about each position of the parts. The symbol with page number(s) indicates the corresponding reference page(s). Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
DTS-ES | NEO:6 | 96/24. Product DTS and DTS-ES | NEO:6 are registered trademarks of DTS, Inc. 96/24 is a trademark of DTS, Inc.
iPodTM
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
2 En
Features
Features
Built-in 7-channel power amplifier
Minimum RMS output power (20 Hz to 20 kHz, 0.06% THD, 8 ) Front: 90 W + 90 W Center: 90 W Surround: 90 W + 90 W Surround back: 90 W + 90 W
INTRODUCTION
SCENE function
17 preset SCENE templates for various situations 4 original SCENE templates for customizing capability Controlling Yamaha SCENE control signal support component (some models only) working with the SCENE function
Other features
YPAO (Yamaha Parametric Room Acoustic Optimizer) for automatic speaker setup 192-kHz/24-bit D/A converter OSD (on-screen display) menus that allow you to optimize this unit to suit your individual audiovisual system 5.1 or 7.1-channel additional input jacks for discrete multichannel input S-video signal input/output capability Component video input/output capability includes (3 COMPONENT VIDEO INs and 1 MONITOR OUT) Digital video signal conversion (composite video S-video component video) capability for monitor out Optical and coaxial digital audio signal jacks Pure Direct mode for pure hi-fi sound for all sources Cinema and music night listening modes Remote control with preset remote control codes capability Zone 2 custom installation facility Zone switching capability between the main zone and Zone 2 using ZONE CONTROL Bi-amplification connection capability Sleep timer
Supplied accessories
Check that you received all of the following parts.
Remote control
POWER POWER
AM loop antenna
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
SELECT
AMP
+
TV VOL
+
TV CH
+
SOURCE
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
A/B/C/D/E
STRAIGHT
RETURN
DISPLAY
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
8
SLEEP
Optimizer microphone
Indoor FM antenna
+ 10
ENT
REC
FREQ/TEXT EON
MACRO
OFF
ON
RENAME
English
Note
The form of the supplied accessories varies depending on the models.
3 En
GETTING STARTED
Getting started
Installing batteries in the remote control VOLTAGE SELECTOR (Asia and General models only)
Caution The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. Rotate the VOLTAGE SELECTOR clockwise or counterclockwise to the correct position using a straight slot screwdriver. Voltages are as follows: Asia model ...................................... 220/230240 V AC, 50/60 Hz General model ........................110/120/220/230240 V AC, 50/60 Hz
VOLTAGE SELECTOR 230240V
2 1 3
1 2
Press the part and slide the battery compartment cover off. Insert the four supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ and ) on the inside of the battery compartment. Slide the cover back until it snaps into place.
Voltage indication
Notes
Change all of the batteries if you notice the following conditions: the operation range of the remote control decreases. the transmit indicator (X) does not flash or its light becomes dim. Do not use an old battery together with a new one. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations. If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the remote control code and program any acquired functions that may have been cleared.
4 En
INTRODUCTION
Center speaker
Surround back right speaker Surround back left speaker Surround left speaker
The following items are not included in the package of this unit. Speakers Front speakers .................................... 2 Center speaker ................................... 1 Surround speakers ............................. 4 Select magnetically shielded speakers. The minimum required speakers are two front speakers. The priority of the requirement of other speakers is as follows: 1. Two surround speakers 2. Center speaker 3. One (or two) surround back speaker(s) Active subwoofer .................................... 1 Select an active subwoofer equipped with an RCA input jack. Speaker cables ........................................ 7 Subwoofer cable ..................................... 1 Select a monaural RCA cable. DVD player ............................................... 1 Select DVD player equipped with coaxial digital audio output jack and composite video output jack. Video monitor........................................... 1 Select a TV monitor, video monitor or projector equipped with a composite video input jack.
DVD player
P. 6
P. 7
Video cable .............................................. 1 Select an RCA composite video cable. Digital coaxial audio cable ..................... 1
P. 9
Enjoy DVD playback!
English
5 En
Be sure to connect the left channel (L), right channel (R), + (red) and (black) properly. Front speakers and center speaker
MULTI CH INPUT
L
CENTER
ZONE 2 OUT
PRE OUT
SINGLE
CENTER
VIDEO
VIDEO
GND
R R
S VIDEO
IN OUT IN OUT
PHONO
CD
DVD
DTV/CBL
IN
DVR
OUT
IN
VCR
OUT
FRONT(6CH)
SB(8CH)
SURROUND
SUB WOOFER
FRONT
SURROUND
SUR. BACK
SUB WOOFER
DVD
DTV/CBL
DVR
VCR
MONITOR OUT
DOCK
HDMI
PR
A PB DVD
COMPONENT VIDEO
PR
DTV/CBL B P B Y
Loosen
Insert
Tighten
MD/CD-R
1
MD/CD-R
2
DVD
3
DTV/CBL
4
CD
5
DVD
6
ANTENNA
DIGITAL OUTPUT
OPTICAL
COAXIAL
DVD IN1
DTV/CBL IN2
OUT
MONITOR OUT
SURROUND SURROUND BACK/BI-AMP
L R L
DVR
CENTER
R
AC OUTLETS
AM GND
IN
OUT
PRESENCE
SINGLE
1 2
Place your speakers and subwoofer in the room. Connect speaker cables to each speaker.
Center speaker
Connect each speaker cable to the corresponding speaker terminal of this unit.
1 2 3 4
To the surround right speaker To the surround back left speaker To the surround left speaker To the surround back right speaker
1 Make sure that this unit and the subwoofer are unplugged from the AC wall outlets. 2 Twist the exposed wires of the speaker cables together to prevent short circuits. 3 Do not let the bare speaker wires touch each other. 4 Do not let the bare speaker wires touch any metal part of this unit.
Connect the subwoofer cable to the SUBWOOFER PRE OUT jack of this unit and the input jack of the subwoofer.
Subwoofer AV receiver
6 En
Connect the video cable to the composite video output jack of your DVD player and DVD VIDEO jack of this unit.
INTRODUCTION
MULTI CH INPUT
L
CENTER
ZONE 2 OUT
PRE OUT
SINGLE
CENTER
VIDEO
VIDEO
GND
R R
S VIDEO
IN OUT IN OUT
PHONO
CD
DVD
DTV/CBL
IN
DVR
OUT
IN
VCR
OUT
FRONT(6CH)
SB(8CH)
SURROUND
SUB WOOFER
FRONT
SURROUND
SUR. BACK
SUB WOOFER
DVD
DTV/CBL
DVR
VCR
MONITOR OUT
DOCK
HDMI
PR
A PB DVD
COMPONENT VIDEO
PR
DTV/CBL B P B Y
MD/CD-R
1
MD/CD-R
2
DVD
3
DTV/CBL
4
CD
5
DVD
6
ANTENNA
DIGITAL OUTPUT
OPTICAL
COAXIAL
DVD IN1
DTV/CBL IN2
OUT
MONITOR OUT
SURROUND SURROUND BACK/BI-AMP
L R L
DVR
CENTER
R
AC OUTLETS
AM GND
IN
OUT
PRESENCE
SINGLE
Make sure that this unit and the DVD player are unplugged from the AC wall outlets.
Video cable
3 1
Connect the digital coaxial audio cable to the digital coaxial audio output jack of your DVD player and the DVD COAXIAL jack of this unit.
DVD player AV receiver
Connect the video cable to the VIDEO MONITOR OUT jack of this unit and the video input jack of your video monitor.
Video monitor AV receiver
Video input jack Digital coaxial audio output jack Digital coaxial audio cable Video cable DVD DIGITAL INPUT coaxial jack VIDEO MONITOR OUT jack
English
7 En
Connect the supplied AM loop antenna and indoor FM antenna to this unit. See page 24 for the connection information.
AM loop antenna
P. 18 Connecting a DVD player via various ways of the connection P. 19 Connecting a DVD recorder or a digital video recorder P. 20 Connecting a set-top box
Indoor FM antenna
P. 20
Close the lever
Insert
Connecting a CD player, an MD recorder or a turntable P. 21 Connecting an external amplifier P. 22 Connecting a DVD player via analog multichannel audio connection P. 22 Connecting a Yamaha iPod universal dock P. 23 Using the REMOTE IN/OUT jacks P. 23 Using the VIDEO AUX jacks on the front panel P. 23 Connecting an outdoor FM/AM antenna P. 24
y
The wire of the AM loop antenna does not have any polarity and you can connect either end of the wire to AM or GND terminal
5
y
Connect the power plug of this unit and other components into the AC wall outlet.
This unit is equipped with AC OUTLET(S) for the power supply of the other components (except Korea model). See page 24 for details.
Note
The type of the power plug is different depending on the models.
8 En
INTRODUCTION
1 2
Turn on the video monitor connected to this unit. Press B MASTER ON/OFF inward to the ON position on the front panel.
Note
When you change the input source or sound field program, the SCENE mode is deactivated, and the indicator on the selected SCENE button turns off.
Press F SCENE1 button. DVD Movie Viewing appears in the front panel display, and this unit automatically optimize own status for the DVD playback.
In the following cases, try pressing the corresponding SCENE button to enjoy the playback of the desired sources. Case A: I want to listen to a music disc from the connected DVD player... Press F SCENE2 (or A SCENE2) to select Music Disc Listening. Case B: I want to watch a TV program... Press F SCENE3 (or A SCENE3) to select TV Viewing. Case C: I want to listen to a music program of the FM/AM radio station... Press F SCENE4 (or A SCENE4) to select Radio Listening.
English
y
The indicator on the selected SCENE button lights up while this unit is in the SCENE mode.
9 En
Notes
To use the TV Viewing template (Case B), you must connect a satellite receiver, a cable TV receiver or an HDTV decoder to this unit in advance. See page 20 for details. To use the Radio Listening template (Case C), you have to tune into the desired radio station. See pages 50 to 52 for the tuning information. To achieve the best possible reception, orient the connected AM loop antenna, or adjust the position of the end of the indoor FM antenna.
y
If you cannot find the desired situation, you can select and change the assigned SCENE template for the SCENE buttons. See page 33 for details.
Additional features
Automatically turning off this unit P. 41
10 En
CONNECTIONS
Connections
Rear panel
AUDIO jacks Connect the analog audio cable plugs. P. 18-21 ZONE 2 OUT jacks Connect the amplifier in Zone 2. P. 95 Video jacks Connect the video cable plugs. P. 18-20
PREPARATION
MULTI CH INPUT jacks Connect the input source component equipped with the multi-channel output jacks. P. 22
AUDIO
L
MULTI CH INPUT
L
CENTER
ZONE 2 OUT
PRE OUT
SINGLE
CENTER
VIDEO
VIDEO
GND
R R
S VIDEO
IN OUT IN OUT
PHONO
CD
DVD
DTV/CBL
IN
DVR
OUT
IN
VCR
OUT
FRONT(6CH)
SB(8CH)
SURROUND
SUB WOOFER
FRONT
SURROUND
SUR. BACK
SUB WOOFER
DVD
DTV/CBL
DVR
VCR
MONITOR OUT
DOCK
HDMI
PR
A PB DVD
COMPONENT VIDEO
PR
DTV/CBL B P B Y
MD/CD-R
1
MD/CD-R
2
DVD
3
DTV/CBL
4
CD
5
DVD
6
ANTENNA
DIGITAL OUTPUT
OPTICAL
COAXIAL
DVD IN1
DTV/CBL IN2
OUT
MONITOR OUT
SURROUND SURROUND BACK/BI-AMP
L R L
DVR
CENTER
R
AC OUTLETS
AM GND
IN
OUT
PRESENCE
SINGLE
DIGITAL INPUT/ OUTPUT jacks Connect the digital audio cable plugs. P. 19-21
AC OUTLET(S) P. 24 P. 16
Connect the FM and AM antenna. P. 24 REMOTE IN/OUT jacks Connect the remote control input and output jacks of the Yamaha components. P. 23
AM GND
IN
OUT
English
11 En
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multichannel audio sources.
PL
C
FL FR
PR
PR PL FR SW C SBL SL SR SBR
30
FL
SL
60
SR
80
SL
SR
SBR
SBL
Front left and right speakers (FL and FR) The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same. Center speaker (C) The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Surround left and right speakers (SL and SR) The surround speakers are used for effect and surround sounds. Surround back left and right speakers (SBL and SBR) The surround back speakers supplement the surround speakers and provide more realistic front-to-back transitions. Presence left and right speakers (PL and PR) The presence speakers supplement the sound from the front speakers with extra ambient effects produced by the sound field programs (see page 42). To use the presence speakers, connect the speakers to EXTRA SP terminals and then set EXTRA SP ASSIGN to PRESENCE (see pages 29 and 70).
0.5 to 1 m (1 to 3 ft) 0.5 to 1 m (1 to 3 ft)
PL
PR
1.8 m (6 ft)
FL
FR
1.8 m (6 ft)
Subwoofer (SW) The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.
12 En
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), + (red) and (black) properly. If the connections are faulty, this unit cannot reproduce the input sources accurately. Caution Before connecting the speakers, make sure that this unit is turned off (see page 25). Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage this unit and/or the speakers. If the speaker wires are short-circuited, CHECK SP WIRES appears in the front panel display. Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the speakers away from the monitor. If you are to use 6 ohm speakers, be sure to set SP IMP. to 6 MIN before using this unit (see page 25). 4 ohm speakers can be also used as the front speakers (see page 99).
PREPARATION
Note
A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the + (red) terminals of this unit and your speaker. Connect the plain cable to the (black) terminals. EXTRA SP terminals Connect the alternative front speaker system (FRONT B), presence speakers or Zone 2 speakers. To select the function of the speakers connected to the EXTRA SP terminals, set the EXTRA SP ASSIGN parameter in SOUND MENU (see page 70). y You can also select the function of the speakers connected to the EXTRA SP terminals in AUTO SETUP (see page 29).
Subwoofer
PRE OUT
SUB WOOFER
SPEAKERS
FRONT B/ZONE2/ R EXTRA SP L FRONT A
R L
CENTER
R
SURROUND
L
SURROUND BACK/BI-AMP
R L
PRESENCE
SINGLE
Left Right Surround speakers Left Right Surround back speakers Left Right Front speakers (FRONT A)
Center speaker
When you use single surround back speaker, connect the speaker to the left SURROUND BACK terminal (SINGLE).
English
13 En
Connections
Connecting the banana plug (except Europe, Asia and Korea models) Tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.
Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits.
10 mm (0.4 in)
Insert one bare wire into the hole on the side of each terminal.
FRONT A
R L
SINGLE L
This unit
Note
When you make the conventional connection, make sure that the shorting bars are put into the terminals appropriately. Refer to the instruction manuals of the speakers for details.
14 En
Connections
DIGITAL
COAXIAL
VIDEO
S VIDEO
COMPONENT VIDEO Y PB PR
(White)
(Red)
(Orange)
(Yellow)
(Green)
(Blue)
(Red)
PREPARATION
PB
PR
Audio jacks
This unit has three types of audio jacks. Connection depends on the availability of audio jacks on your other components. AUDIO jacks For conventional analog audio signals transmitted via left and right analog audio cables. Connect red plugs to the right jacks and white plugs to the left jacks. DIGITAL COAXIAL jacks For digital audio signals transmitted via coaxial digital audio cables. DIGITAL OPTICAL jacks For digital audio signals transmitted via optical digital audio cables. Notes
You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the signals input at the COAXIAL jack. All digital input jacks are compatible with digital signals with up to 96 kHz of sampling frequency. Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.
Video jacks
This unit has three types of video jacks. Connection depends on the availability of input jacks on your video monitor. VIDEO jacks For conventional composite video signals transmitted via composite video cables. S VIDEO jacks For S-video signals, separated into the luminance (Y) and chrominance (C) video signals transmitted on separate wires of S-video cables. COMPONENT VIDEO jacks For component video signals, separated into the luminance (Y) and chrominance (PB, PR) video signals transmitted on separate wires of component video cables. y
This unit is equipped with the video conversion function. See pages 17 and 79 for details.
English
15 En
Connections
Information on HDMI
HDMI compatibility with this unit
Audio signal types 2ch Linear PCM Multi-ch Linear PCM DSD Bitstream Audio signal formats 2ch, 32-192 kHz, 16/20/24 bit 8ch, 32-192 kHz, 16/20/24 bit 2/5.1ch, 2.8224 MHz, 1 bit Dolby Digital, DTS Compatible HDMI components CD, DVD-Video, DVD-Audio, etc. DVD-Audio, etc.
HDMI
y
SACD, etc. DVD-Video, etc. We recommend using an HDMI cable shorter than 5 meters (16 feet) with the HDMI logo printed on it. Use a conversion cable (HDMI jack DVI-D jack) to connect this unit to other DVI components.
This units HDMI interface is based on the following standards: HDMI Version 1.2a (High-Definition Multimedia Interface Specification Version 1.2a) licensed by HDMI Licensing, LLC. HDCP Revision 1.1 (High-bandwidth Digital Content Protection System Revision 1.1) licensed by Digital Content Protection, LLC.
Notes
Do not disconnect or connect the cable or turn off the power of the HDMI components connected to the HDMI OUT jack of this unit while data is being transferred. Doing so may disrupt playback or cause noise. Audio signals input at input jacks other than the HDMI IN 1 or HDMI IN 2 jack of this unit cannot be digitally output at the HDMI OUT jack. If you turn off the power of the video monitor connected to the HDMI OUT jack via a DVI connection, this unit may fail to establish the connection to the component.
Notes
When CPPM copy-protected DVD audio is played back, video and audio signals may not be output depending on the type of the DVD player. This unit is not compatible with HDCP-incompatible HDMI or DVI components. You can check the potential problem about the HDMI connection (see page 41).
16 En
Connections
Input
Output
PREPARATION
AUDIO
S VIDEO
VIDEO
Digital output Through Analog output Video conversion ON (see page 79)
Notes
2-channel as well as multi-channel PCM, Dolby Digital and DTS signals input at the HDMI IN 1 or HDMI IN 2 jack can be output at the HDMI OUT jack only when SUPPORT AUDIO is set to OTHER (see page 75). Audio signals input at the HDMI IN jacks are not output at the AUDIO output and DIGITAL OUTPUT jacks.
Notes
When the analog video signals are input at the COMPONENT VIDEO, S VIDEO and VIDEO jacks, the priority order of the input signals is as follows: 1. COMPONENT VIDEO 2. S VIDEO 3. VIDEO Digital video signals input at the HDMI IN 1 or HDMI IN 2 jack cannot be output from analog video output jacks. This unit does not accept analog component video signals with 1080p of resolution. The OSD signal is not output at the VCR OUT, DVR OUT and HDMI MONITOR OUT jacks and is not recorded. This unit does not deinterlace any analog video signals.
English
17 En
Connections
y
You can choose to play back HDMI audio signals on this unit or on another HDMI component connected to the HDMI OUT jack of this unit. Use the SUPPORT AUDIO parameter in SOUND MENU to select the component to play back HDMI audio signals (see page 75).
VIDEO
VIDEO
S VIDEO
MONITOR OUT
HDMI
COMPONENT VIDEO
PR
PB
OUT
MONITOR OUT
PR
PB
HDMI in
Component video in
S V
18 En
Connections
Notes
When VIDEO CONV. is set to OFF (see page 79), be sure to make the same type of video connections as those made for your TV (see page 18). For example, if you connected your TV to the VIDEO MONITOR OUT jack of this unit, connect your other components to the VIDEO jacks.
PREPARATION
DVD player
PR
PB
AUDIO
VIDEO
VIDEO
S VIDEO
DVD
DVD
HDMI
PR
A PB DVD
COMPONENT VIDEO
DVD
3
DVD
6
OPTICAL
COAXIAL
DVD IN1
DIGITAL INPUT
English
19 En
Connections
S-video out
V S V S
AUDIO
VIDEO
VIDEO
S VIDEO
IN OUT IN OUT
IN
DVR
OUT
IN
VCR
OUT
DVR
VCR
COMPONENT VIDEO
PR
PB
DVR
PR
PB
S-video out
S-video in
Video out
Video in
L R L R
Audio out
HDMI out
PR
PB
VIDEO
S VIDEO
DTV/CBL
DTV/CBL
HDMI
COMPONENT VIDEO
PR
DTV/CBL B P B Y
DTV/CBL
4
OPTICAL
DTV/CBL IN2
DIGITAL INPUT
20 En
Connections
PREPARATION
Turntable
CD player
Audio out
Coaxial out
Ground
L
Audio out
AUDIO
GND
R
PHONO
CD
MD/CD-R
1
MD/CD-R
2
CD
5
DIGITAL OUTPUT
COAXIAL
DIGITAL INPUT
Optical out
Audio out
Optical in
Audio in
English
21 En
Connections
5
PRE OUT
SINGLE
CENTER
3 SUR.BACK PRE OUT jacks Surround back channel output jacks. When you only connect one external amplifier for the surround back channel, connect it to the SINGLE jack. Notes
FRONT
SURROUND
SUR. BACK
SUB WOOFER
1 FRONT PRE OUT jacks Front channel output jacks. 2 SURROUND PRE OUT jacks Surround channel output jacks.
When BI-AMP is set to ON, this unit outputs the front channel audio signals at the SUR.BACK PRE OUT jacks. The audio signals output at the SUR.BACK PRE OUT jacks differ depending on the EXTRA SP ASSIGN setting (see page 70).
4 SUBWOOFER PRE OUT jack Connect a subwoofer with a built-in amplifier. 5 CENTER PRE OUT jack Center channel output jack.
CENTER
MULTI CH INPUT
L
CENTER
R
FRONT(6CH)
*1
R
SB(8CH)
SURROUND
SUB WOOFER
FRONT(6CH)
SB(8CH)
SURROUND
SUB WOOFER
Surround out
Surround out
Subwoofer out
Center out
Front out
Subwoofer out
Center out
Front out
The analog audio input jacks assigned as FRONT in MULTI CH SET (see page 78).
22 En
Connections
y
If the components have the capability of the SCENE control signals, this unit can automatically activate the corresponding components and start the playback when you use one of the SCENE buttons. Refer to the owners manuals for details about the capability of the SCENE control signals of the components. Connect the REMOTE OUT jack of this unit and the remote control input jack of the components to control the components by using the SCENE feature. If the component connected to the REMOTE OUT jack is not the Yamaha product, set SCENE IR in the advanced setup menu to OFF (see page 101).
PREPARATION
DOCK
Notes
Yamaha iPod universal dock (such as the YDS-10, sold separately)
The audio signals input at the DOCK terminal on the rear panel take priority over the ones input at the VIDEO AUX jacks. To reproduce the source signals input at these jacks, select V-AUX as the input source.
SPEAKERS
FM/AM
A/B/C/D/E
PRESET/TUNING
MEMORY
TUNING AUTO/MAN'L
SCENE
SILENT CINEMA
EFFECT
S VIDEO
VIDEO
AUDIO
OPTICAL
REMOTE
S VIDEO VIDEO L AUDIO R OPTICAL
IN
OUT
Remote control in
S-Video output
Video output
Audio output
Optical output
English
23 En
Connections
AC OUTLETS
Notes
The AM loop antenna should be placed away from this unit. The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas.
AM loop antenna (supplied) To the AC wall outlet
AC OUTLET(S) (SWITCHED)
Indoor FM antenna (supplied)
ANTENNA
U.K. and Australia models..................................... 1 outlet Korea model............................................................... None Other models......................................................... 2 outlets Use these outlet(s) to supply power to any connected components. Connect the power cable of your other components to these outlet(s). Power to these outlet(s) is supplied when the main zone or Zone 2 is turned on. However, power to these outlet(s) is cut off when the main zone and Zone 2 are turned off or when B MASTER ON/ OFF on the front panel is pressed and released outward to the OFF position. For information on the maximum power or the total power consumption of the components that can be connected to these outlet(s), see Specifications on page 114. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, the stored data will be lost in case the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than one week.
AM GND
FM
Outdoor AM antenna
Use a 5 to 10 m (16 to 33 ft) vinyl-covered wire extended outdoors from a window.
24 En
Connections
1 2
Make sure this unit is turned off. Refer to the right column for details. Press and hold C TONE CONTROL on the front panel and then press B MASTER ON/ OFF inward to the ON position to turn on this unit. This unit turns on, and the advanced setup menu appears in the front panel display.
TONE CONTROL
PREPARATION
Turning off this unit Press B MASTER ON/OFF on the front panel again to release it outward to the OFF position to turn off this unit.
Notes
A MAIN ZONE ON/OFF on the front panel as well as I POWER and H STANDBY on the remote control are operational only when B MASTER ON/OFF is pressed inward to the ON position. As usual, we recommend using the standby mode to turn off this unit.
MASTER
ON
OFF
Rotate the D PROGRAM selector on the front panel to select SP IMP.. SP IMP. and the current speaker impedance setting (8 MIN) appear in the front panel display. Press C TONE CONTROL on the front panel repeatedly to select 6 MIN. Press B MASTER ON/OFF on the front panel to release it outward to the OFF position to save the new setting and turn off this unit. Note
The setting you made is reflected next time you turn on this unit.
Set the main zone to the standby mode Press A MAIN ZONE ON/OFF (or H STANDBY) to set the main zone to the standby mode.
In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control.
4 5
Turning on the main zone from the standby mode Press A MAIN ZONE ON/OFF (or I POWER) to turn on the main zone.
y
You can also turn on the main zone by pressing F SCENE (or A SCENE) buttons. When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound. These buttons are operational only when B MASTER ON/ OFF is pressed inward to the ON position.
English
25 En
Connections
4
VCR
VIRTUAL
5
DVR
6
V-AUX
DOCK
7
DTV/CBL
8
DVD MD/CD-R
9
TUNER
0
CD
MUTE
A
PHONO
VOLUME
dB
t
q EX
HiFi DSP
96/24 LFE ft
PCM
mS dB
L C R SL SB SR
L ........ Europe model only 1B Input signal indicators Lights up when this unit is reproducing DSD (Direct Stream Digital) or PCM (Pulse Code Modulation) digital audio signals. 2C Decoder indicators The respective indicator lights up when any of the decoders of this unit function. 3 ENHANCER indicator Lights up when the Compressed Music Enhancer mode is selected (see page 46). 4 HDMI indicator Lights up when the signal of the selected input source is input at HDMI IN 1 or HDMI IN 2 jacks (see page 16). 5 SILENT CINEMA indicator Lights up when headphones are connected and a sound field program is selected (see page 46). 6 DOCK indicator Lights up when you station your iPod in a Yamaha iPod universal dock (such as the YDS-10, sold separately) connected to the DOCK terminal of this unit (see page 23) and V-AUX is selected as the input source. The DOCK indicator also lights up when this unit is charging the battery of the stationed iPod in the standby mode. 7 Input source indicators The corresponding cursor lights up to show the currently selected input source. 8 YPAO indicator Lights up when you run AUTO SETUP and when the speaker settings set in AUTO SETUP are used without any modifications (see page 28). 9 Tuner indicators Lights up when this unit is in the FM or AM tuning mode (see pages 50 to 52). 0 MUTE indicator Flashes while the MUTE function is on (see page 40). A VOLUME level indicator Indicates the current volume level. D Sound field indicators Light up to indicate the active DSP sound fields. E VIRTUAL indicator Lights up when Virtual CINEMA DSP is active (see page 46). F Headphones indicator Lights up when headphones are connected (see page 40). G SP A B indicators Light up according to the set of front speakers selected. H ZONE2 indicator Lights up when Zone 2 is turned on (see page 96). I NIGHT indicator Lights up when you select a night listening mode (see page 49). J DSP indicators The respective indicator lights up when any of the DSP sound field programs are selected (see page 42). K Multi-information display Shows the name of the current sound field program and other information when adjusting or changing settings.
26 En
Connections
L Radio Data System indicators (Europe model only) PS, PTY, RT and CT Light up according to the selected Radio Data System display mode. EON Lights up when the EON data service is being received. PTY HOLD Lights up while searching for the Radio Data System stations in the PTY SEEK mode. M SLEEP indicator Lights up while the sleep timer is on (see page 41). N 96/24 indicator Lights up when a DTS 96/24 signal is input to this unit. O Input channel and speaker indicators
PREPARATION
30
30
LFE
L C R SL SB SR
LFE indicator Presence speaker indicators Input channel indicators Surround back speaker indicators
Infrared window (Y) Outputs infrared control signals. Aim this window at the component you want to operate. Transmit indicator (X) Flashes while the remote control is sending infrared signals. Display window (J) Shows the name of the selected input source that you can control. Operation mode selector (L) The function of some buttons depends on the operation mode selector position. AMP Operates the amplifier function of this unit. SOURCE Operates the component selected with an input selector button (see page 84). TV Operates the TV assigned to either DTV/CBL or PHONO (see page 83). Notes
Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following types of conditions: places of high humidity, such as near a bath places of high temperatures, such as near a heater or stove places of extremely low temperatures dusty places To set the remote control codes for other components, see page 85.
LFE indicator Lights up when the input signal contains the LFE signal. Input channel indicators Indicate the channel components of the current digital input signal. Presence and surround back speaker indicators Light up according to the number of presence and surround back speakers set for EXTRA SP ASSIGN (see page 70) and SUR. B L/R SP (see page 71) in SOUND MENU when this unit is in the auto setup (see page 28) or the speaker level setting in SOUND MENU (see page 72) procedure. y
You can make settings for surround back speakers automatically by running AUTO SETUP (see page 28) or manually by adjusting settings for SUR. B L/R SP (see page 71) in SOUND MENU. To use the presence speakers, set EXTRA SP ASSIGN to PRESENCE (see page 29 or 70).
English
27 En
Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel.
OPTIMIZER MIC VIDEO AUX
S VIDEO
VIDEO
AUDIO
OPTICAL
y
You can run AUTO SETUP using the system menu that appears in the OSD or in the front panel display. This manual uses the OSD illustrations to explain the AUTO SETUP procedure. Before performing operations, set the operation mode selector on the remote control to L AMP. This unit uses the speakers connected to the FRONT A speaker terminals as the front speakers for the adjustment.
Omni-directional microphone
Make sure of the following check points before starting the AUTO SETUP operations. Speakers are connected appropriately. Headphones are disconnected from this unit. This unit and the video monitor are turned on. The connected subwoofer is turned on and the volume level is set to about half way (or slightly less). The crossover frequency controls of the connected subwoofer is set to the maximum. The room is sufficiently quiet.
Place the optimizer microphone at your normal listening position on a flat level surface with the omni-directional microphone heading upward.
Optimizer microphone
y
It is recommended that you use a tripod (etc.) to affix the optimizer microphone at the same height as your ears would be when you are seated in your listening position. You can use the attached screw of a tripod (etc.) to fix the optimizer microphone to the tripod (etc.).
28 En
Press D l / h to select the desired setting for EXTRA SP ASSIGN and then press D n. Extra speaker assignment EXTRA SP ASSIGN Selects the function of the speakers connected to the EXTRA SP terminals. Choices: FRONT B, ZONE2, PRESENCE, NONE When you use the alternative front speaker system (see page 38) Select FRONT B. When you use the Zone 2 speakers (see page 96) Select ZONE2 to set the function of the speakers to the Zone 2 speakers. This unit drives the Zone 2 speakers by using the internal amplifier. When you use the presence speakers (see page 12) Select PRESENCE to set the function of the speakers to the presence speakers. When you do not use the EXTRA SP terminals Select NONE to deactivate the EXTRA SP terminals. Note
If you select ON in BI-AMP (see page 101), you cannot select PRESENCE or ZONE2 in EXTRA SP ASSIGN.
Press D l / h to select the desired setting of EQ and then press D n. Parametric equalizer type EQ Parametric equalizer adjusts the level of the specified frequency bands. This unit automatically selects the crucial frequency bands for the listening room and adjusts the level of the selected frequency bands to create a cohesive sound field in the room. You can select the type of the parametric equalizer adjustment from the following choices. Choices: NATURAL, FLAT, FRONT Select NATURAL to average out the frequency response of all speakers with higher frequencies being less emphasized. Recommended if the FLAT setting sounds a little harsh. Select FLAT to average the frequency response of all speakers. Recommended if all of your speakers are of similar quality. Select FRONT to adjust the frequency response of each speaker in accordance with the sound of your front speakers. Recommended if your front speakers are of much higher quality than your other speakers.
PREPARATION
Press D n to select START and then press D ENTER to start the setup procedure. This unit starts the auto setup procedure. Loud test tones are output from each speaker during the auto setup procedure. Once all items are set, the AUTO:RESULT display appears in the OSD. Notes
During the auto setup procedure, do not perform any operation on this unit. We recommend getting out of the room while this unit is in the auto setup procedure. It takes approximately 3 minutes for this unit to complete the auto setup procedure.
Press D l / h to select SETUP. Choices: AUTO, RELOAD, UNDO, DEFAULT Select AUTO to automatically run the entire AUTO SETUP procedure. Select RELOAD to reload the last AUTO SETUP settings and override the previous settings. Select UNDO to undo the last AUTO SETUP settings and restore the previous settings. Select DEFAULT to reset the AUTO SETUP parameters to the initial factory settings. Notes
RELOAD or UNDO is available only when you have previously run AUTO SETUP and confirmed the results. RELOAD or UNDO is not available when you change the setting of BI-AMP in the advanced setup (see page 101) or EXTRA SP ASSIGN in SOUND MENU (see page 70).
English
29 En
This unit performs the following checks: Speaker wiring WIRING Checks which speakers are connected and the polarity of each speaker. Speaker size SIZE Checks the frequency response of each speaker and sets the appropriate low-frequency crossover for each channel. Speaker distance DISTANCE Checks the distance of each speaker from the listening position and adjusts the timing of each channel. Equalizing EQUALIZING Checks and adjusts the tonal characteristics of all the speakers by the setting of EQ. Speaker level LEVEL Checks and adjusts the volume level of each speaker. The display changes as follows.
AUTO:MENU EXTRA SP ASSIGN ZONE2 >FRONT B PRESENCE NONE SETUP;;;;;;;AUTO EQ;;;;;;;NATURAL . START
The results displayed under RESULT are as follows. Number of speakers SP Displays the number of speakers connected to this unit in the following order: Front/Back/Subwoofer Speaker distance DIST Displays the speaker distance from the listening position in the following order: Closest speaker distance/Farthest speaker distance Speaker level LVL Displays the speaker output level in the following order: Lowest speaker output level/Highest speaker output level Notes
If E-10:INTERNAL ERROR appears during the testing procedure, restart from step 4. If you selected RELOAD in step 4, no test tones are output. If an error occurs during the AUTO:CHECK procedure, the setup procedure is canceled and an error screen appears. For details, see If an error screen appears on page 32. When this unit detects potential problems during the AUTO SETUP procedure, WARNING and the number of warning messages appears in the above of RESULT (see page 32). Depending on the listening environment, SWFR PHASE:REV appears during the AUTO:CHECK procedure and SUBWOOFER PHASE in SOUND MENU (see page 72) is automatically set to REVERSE.
AUTO:CHECK INITIALIZING . WIRING SIZE/DISTANCE EQUALIZING LEVEL CHECK CH=CENTER |||||;;;;;;;; [ ]:Exit
AUTO:RESULT . RESULT SP : 3/4/0.1 DIST: 4.50/5.30m LVL : -9.0/+6.5dB > SET CANCEL [ ]/[ ]:Up/Down [ENTER]:Enter
[[]/[[]:Select [ENTER]:Return
30 En
10
PREPARATION
11
Make sure the pointer is pointing at SET and CANCEL and then press D l / h to select SET or CANCEL.
AUTO:RESULT RESULT SP : 3/4/0.1 DIST: 4.50/5.30m LVL : -9.0/+6.5dB . > SET CANCEL
Choices: SET, CANCEL Select SET to confirm the AUTO SETUP results. Select CANCEL to cancel the AUTO SETUP results.
Results of the speaker output level
12
y
If you are not satisfied with the results or want to manually adjust each parameter, run MANUAL SETUP (see page 67).
Press D ENTER to confirm your selection. The top SET MENU display appears in the OSD.
SET MENU . ;AUTO SETUP ;MANUAL SETUP .A;SIGNAL INFO [ ]/[ ]:Up/Down [ENTER]:Enter
Notes
The distances displayed in the DISTANCE results may be longer than the actual distance depending on the characteristics of your subwoofer. In the EQ results, different values may be set for the same frequency to provide finer adjustments.
13 14
Press N SET MENU to exit from SET MENU. Disconnect the optimizer microphone from this unit. The optimizer microphone is sensitive to heat. Keep it away from direct sunlight and do not place it on top of this unit. y
If you change speakers, speaker positions, or the layout of your listening environment, run AUTO SETUP again to recalibrate your system.
English
31 En
[[]/[[]:Select [ENTER]:Enter
y
For details about each warning message, see the AUTO SETUP section in Troubleshooting on page 107. When the corresponding warning message is not applicable to a speaker, is displayed instead.
Choices: RETRY, EXIT Select RETRY to retry the AUTO SETUP procedure. Select EXIT to exit from the AUTO SETUP procedure.
If WARNING appears
When this unit detects potential problems during the AUTO SETUP procedure, WARNING appears in the AUTO:RESULT display. Check the warning messages to correct your speaker settings. Note
Warnings differ from errors in that warnings do not cancel the AUTO SETUP procedure.
Make sure the pointer is pointing at WARNING and then press D ENTER to display the detailed information about the warning. The number on the right of WARNING indicates the number of warning messages.
AUTO:RESULT . WARNING(3) RESULT SP : 3/4/0.1 DIST: 4.50/5.30m LVL : -9.0/+6.5dB >SET CANCEL [ ]/[ ]:Up/Down [ENTER]:Enter
32 En
Rotate the I INPUT selector (or set the operation mode selector to L AMP and then press D l / h) to select the desired template.
DVD Viewing
3
Press the F SCENE (or A SCENE) button again to confirm the selection. The selected SCENE template is assigned to the SCENE button. BASIC OPERATION
or
Front panel
Remote control
Notes
If you do not carry out any operation within 30 seconds from the last operation in these steps, this procedure is automatically canceled. Once the desired SCENE templates are assigned to the corresponding SCENE buttons, you need to set the input source of the SCENE template on the remote control. See page 82 for details.
Front panel
Remote control
Flashes
English
33 En
SCENE templates DVD Viewing DVD Movie Viewing DVD Live Viewing
DVR Viewing Disc Hifi Listening Music Disc Listening Disc Listening
2
CD
Radio programs
TUNER (FM/AM)
Radio Listening
iPod
*
DOCK
iPod Listening
To listening to the iPod, you need to connect a Yamaha iPod universal dock (sold separately) to this unit (see page 56).
TV programs
DTV/CBL
Video games
V-AUX
Vinyl records
PHONO
LP Record Listening
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 36 for details.
34 En
DVD Live Viewing DVR Viewing Disc Hifi Listening Music Disc Listening
2
ENTERTAINMENT Music Video MOVIE Drama PURE DIRECT STEREO 2ch STEREO
Select this SCENE template when you enjoy the music live video on your DVD player. Select this SCENE template when you play back movies on your digital video recorder. Select this SCENE template when you enjoy the high fidelity sound of the music discs on your DVD player. Select this SCENE template when you play back music discs on your DVD player.
BASIC OPERATION
STEREO 7ch STEREO PURE DIRECT STEREO 2ch STEREO STEREO 7ch STEREO MUSIC ENHANCER 7ch Enhancer MUSIC ENHANCER 7ch Enhancer STRAIGHT
Select this SCENE template when you play back music sources on your DVD player as the background music. Select this SCENE template when you enjoy the high fidelity sound of the music discs on your CD player. Select this SCENE template when you play back music discs on your CD player. Select this SCENE template when you play back music source on your CD player as the background music. Select this SCENE template when you enjoy FM or AM radio programs.
iPod Listening
DOCK (V-AUX)
Select this SCENE template when you play back music on your iPod stationed in a Yamaha iPod universal dock.
TV Viewing
3
DTV/CBL
Select this SCENE template when you enjoy general programs on your TV.
DTV/CBL V-AUX*2
ENTERTAINMENT Sports ENTERTAINMENT Action Game ENTERTAINMENT Roleplaying Game PURE DIRECT
*2
Select this SCENE template when you enjoy sports programs on your TV. Select this SCENE template when you play action games such as car racing and FPS games. Select this SCENE template when you play role-playing games. Select this SCENE template when you play back vinyl records on your turntable.
V-AUX*2 PHONO
When the connected DVD player or CD player has the capability of the SCENE control signals and is connected to the REMOTE OUT jack of this unit, this unit operates the DVD player or CD player worked with the SCENE features.
You can select V-AUX as the input source even if your iPod is stationed in the Yamaha Universal Dock connected to this unit.
English
35 En
Press D k / n to select the desired parameter of the SCENE template and then D l / h to select the desired value of the selected parameter. You can adjust the following parameters for a SCENE template: INPUT: MODE: The input source component. The active sound field programs, STRAIGHT or Pure Direct mode. NIGHT: The night listening mode (see page 49). SYSTEM: Keeps the current night listening mode. CINEMA: Sets the night listening mode to the CINEMA mode. MUSIC: Sets the night listening mode to the MUSIC mode.
4
y
An asterisk mark (*) appears by the name of the original SCENE template.
1 2
Turn on the video monitor connected to this unit. Set the operation mode selector to L AMP and then press and hold the desired A SCENE button for 3 seconds. The SCENE template customizing screen appears on the video monitor.
SCENE1 .p DVD Viewing [ INPUT: DVD MODE: STRAIGHT NIGHT: SYSTEM [ENTER]:Rename [SCENE1]:SET [RETURN]:STATUS
Notes
Once the desired SCENE templates are assigned to the corresponding A SCENE buttons, you need to set the input source of the SCENE template on the remote control. See page 82 for details. You can create a customized SCENE template for each SCENE button, and if you create another customized SCENE template, this unit overwrites the old customized SCENE template with the new one. The newly created template is only available for the assigned SCENE button.
Note
When the SCENE template you want to customize is not assigned to any of the A SCENE buttons, press D l / h repeatedly to recall the desired SCENE template on the menu screen.
36 En
PLAYBACK
Playback
Caution Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS. y
To play DTS-encoded CDs when using a digital audio connection, set DECODER MODE in INPUT MENU to DTS before the playback (see page 78).
Start playback on the selected source component or select a broadcast station. Refer to the operating instructions for the source component. See page 50 for details about tuning instructions. Rotate 0 VOLUME (or press K VOLUME +/) to adjust the volume to the desired output level. y
See page 48 to adjust the level of each speaker. This does not affect the AUDIO OUT (REC) level. You can set the initial volume level and maximum volume level (see page 75).
y
Before performing operations, set the operation mode selector on the remote control to L AMP.
BASIC OPERATION
Basic procedure
1
Turn on the video monitor connected to this unit. y
See page 40 to display the input source information.
Rotate the D PROGRAM selector (or press one of the sound field program selector buttons (U) repeatedly) to select the desired sound field program. The name of the selected sound field program appears in the front panel display. See page 42 for details about sound field programs.
Rotate the I INPUT selector (or press one of the input selector buttons (B)) to select the desired input source. The name of the currently selected input source appears in the front panel display for a few seconds.
Available input sources
VCR DVR V-AUX DTV/CBL DVD MD/CD-R TUNER CD PHONO
Sci-Fi
Currently selected sound field program
Note
Sound field programs cannot be selected when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 38).
INPUT: DVD
Currently selected input source
y
Choose a sound field program based on your listening preference, not merely on the name of the program. When you select an input source, this unit automatically selects the last sound field program used with the corresponding input source. To display information about the currently selected sound field program in the OSD, see page 59 for details.
y
The corresponding input selector button on the remote control for the currently selected input source lights up for approximately 5 seconds after you press any buttons on the remote control, showing which source component is currently being operated.
English
37 En
Playback
Use this feature to turn the front speaker system (FRONT A and/or FRONT B) on or off. Press 1 SPEAKERS on the front panel repeatedly to turn on or off the set of front speakers connected to the FRONT A and/or EXTRA SP speaker terminals. The active front speaker set changes as follows:
FRONT A FRONT B
Notes
FRONT A and B or FRONT B setting is not available when EXTRA SP ASSIGN is set to PRESENCE, ZONE 2 or NONE (see page 70). Turn off the volume level of this unit when you switch the front speaker setting.
Note
Sound field programs and the night listening mode cannot be selected when the component connected to the MULTI CH INPUT jacks is selected as the input source.
38 En
Playback
1 2
Turn on the video monitor connected to this unit. Set the operation mode selector to L AMP and then press R DISPLAY on the remote control. The current status screen appears in the OSD.
STATUS VOL:-40.0dB MOVIE Sci-Fi INPUT: A.SEL: DVD HDMI
Press H AUDIO SELECT (or O AUDIO) repeatedly to select the desired audio input jack select setting.
Available input sources
VCR DVR V-AUX DTV/CBL DVD MD/CD-R TUNER CD PHONO
BASIC OPERATION
NIGHT: OFF
A.SEL: AUTO
Currently selected audio input jack select setting
y
You can select the amount of time that the current status is displayed in the OSD by using the OSD-AMP parameter in OPTION MENU (see page 79).
AUTO
Automatically selects input signals in the following order: (1) HDMI (2) Digital signals (3) Analog signals Selects only HDMI signals. When HDMI signals are not input, no sound is output. Automatically selects input signals in the following order: (1) Digital signals input at the COAXIAL jack. (2) Digital signals input at the OPTICAL jack. When no signals are input, no sound is output. Selects only analog signals. If no analog signals are input, no sound is output.
Note
The OSD signal is not output at the VIDEO output jacks and will not be recorded.
HDMI COAX/OPT
ANALOG
Note
This feature is not available when no digital input jacks (OPTICAL, COAXIAL and HDMI) are assigned. Use I/O ASSIGNMENT in INPUT MENU to reassign the respective input jack (see page 76).
English
39 En
Playback
VOLUME
SPEAKERS
EDIT PRESET/TUNING
FM/AM
A/B/C/D/E
PRESET/TUNING
MEMORY
TUNING AUTO/MAN'L
ZONE 2 ON/OFF
ZONE CONTROL
SCENE
SILENT CINEMA
EFFECT
S VIDEO
VIDEO
AUDIO
PHONO
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
y y
When you select a sound field program, SILENT CINEMA mode activates automatically (see page 46). Set the BGV parameter in the MULTI CH SET menu to the desired setting to select the default background video input source of the MULTI CH INPUT sources (see page 78).
Notes
When you connect headphones, no signals are output at the speaker terminals. All Dolby Digital and DTS audio signals are mixed down to the left and right headphone channels.
Set the operation mode selector to L AMP and then press N SET MENU on the remote control. The top SET MENU display appears in the OSD.
SET MENU . ;AUTO SETUP ;MANUAL SETUP .A;SIGNAL INFO [ ]/[ ]:Up/Down [ENTER]:Enter
Press D n repeatedly to select SIGNAL INFO and then press D ENTER. The audio information about the input source appears in the OSD. Press D l / h to toggle between the audio and video information displays.
40 En
Playback
Press N SET MENU on the remote control again to exit from SET MENU.
Audio information
FORMAT
Signal format. When this unit cannot detect a digital signal, it automatically switches to analog input. The number of samples per second taken from a continuous signal to make a discrete signal. The number of source channels in the input signal (front/surround/LFE). For example, a multi-channel soundtrack with 3 front channels, 2 surround channels and LFE, is displayed as 3/2/0.1. The number of bits passing a given point per second. Flag data encoded in DTS, Dolby Digital, or PCM signals that cue this unit to automatically switch decoders.
SAMPLING CHANNEL
BITRATE FLAG
SLEEP OFF
SLEEP 30min
Note
--- appears when this unit cannot display the corresponding information.
The SLEEP indicator flashes while you are switching the amount of time for the sleep timer. Once the sleep timer is set, the SLEEP indicator lights up in the front panel display, and the display returns to the selected sound field program.
Flashes
BASIC OPERATION
Video information
SLEEP
HDMI RES.
Resolution of the HDMI signals input or output at the HDMI IN/OUT jacks of this unit. Error message for HDMI sources or connected HDMI devices. See page 107 for details.
SLEEP 120min
Lights up
HDMI ERROR
SLEEP
STRAIGHT
Canceling the sleep timer
Press S SLEEP on the remote control repeatedly until SLEEP OFF appears in the front panel display.
Disappears
SLEEP OFF
The SLEEP indicator turns off, and SLEEP OFF disappears from the front panel display after a few seconds. y
The sleep timer setting can also be canceled by pressing H STANDBY (or A MAIN ZONE ON/OFF) to set the main zone to the standby mode.
English
41 En
MOVIE
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest science fiction and special effects-featuring movies. You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation between dialog, sound effects and background music.
Program description
42 En
Notes
The available sound field parameters differ depending on the settings of the speakers. DIALG.LIFT is available only when EXTRA SP ASSIGN in SPEAKER SET is set to PRESENCE (see page 70).
CLASSICAL ENTERTAIN
1 3
CLASSICAL
Hall in Munich
HiFi DSP
This sound field simulates a concert hall with approximately 2500 seats in Munich, using stylish wood for the interior finishing as normal standards for European concert halls. Fine, beautiful reverberations spread richly, creating a calming atmosphere. The listener's virtual seat is at the center left of the arena.
DIALG.LIFT
1 3
CLASSICAL
Hall in Vienna
HiFi DSP
This is an approximately 1700-seated, middle-sized concert hall with a shoebox shape that is traditional in Vienna. Pillars and ornate carvings create extremely complex reflections from all around the audience, producing a very full, rich sound.
BASIC OPERATION
DIALG.LIFT
CLASSICAL
Chamber
HiFi DSP
This program creates a relatively wide space with a high ceiling like an audience hall in a palace. It offers pleasant reverberations that are suitable for courtly music and chamber music.
LIVENESS REV.TIME
DIALG.LIFT
LIVE/CLUB
Cellar Club
HiFi DSP
This program simulates a live house with a low ceiling and homey atmosphere. A realistic, live sound field features powerful sound as if the listener is in a row in front of a small stage.
DIALG.LIFT
LIVE/CLUB
HiFi DSP
This is the sound field of a rock music live house in Los Angeles, with approximately 460 seats. The listener's virtual seat is at the center left of the hall.
REV.TIME REV.DELAY
LIVE/CLUB
HiFi DSP
This is the sound field at stage front in The Bottom Line, a famous New York jazz club. The floor can seat 300 people to the left and right in a sound field offering real and vibrant sound.
DIALG.LIFT
English
43 En
ENTERTAINMENT
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live feeling. In sports broadcasts, the voices of the commentator and sportscaster are positioned clearly at the center while the atmosphere of the stadium expands in an optimum space to offer the listeners with a feeling of presence in the stadium.
ENTERTAINMENT
Action Game
This sound field has been suitable for action games such as car racing and FPS games. It uses the reflection data that limits the effects range per channel in order to offer a powerful playing environment with a being-there feeling by enhancing various effects tones while maintaining a clear sense of directions.
ENTERTAINMENT
Roleplaying Game
This sound field has been suitable for role-playing and adventure games. It combines the sound field effects for movies and the sound field designs for Action Game to represent the depth and 3D feeling of the field during play, while offering movie-like surround effects in the movie scenes in the game.
2 3
ENTERTAINMENT
Music Video
HiFi DSP
This sound field offers an image of a concert hall for live performance of pop, rock and jazz music. The listener can indulge oneself in a hot live space thanks to the presence sound field that emphasizes the vividness of vocals and solo play and the beat of rhythm instruments, and to the surround sound field that reproduces the space of a big live hall.
44 En
Notes
The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit. DIALG.LIFT is available only when EXTRA SP ASSIGN in SPEAKER SET is set to PRESENCE (see page 70).
MOVIE
MOVIE
Standard
This program creates a sound field emphasizing the surrounding feeling without disturbing the original acoustic positioning of multi-channel audio such as Dolby Digital and DTS. It has been designed with the concept of an ideal movie theater, in which the audience is surrounded by beautiful reverberations from the left, right and rear.
SB LIVENESS DIALG.LIFT
MOVIE
Spectacle
This program represents the spectacular feeling of large-scale movie productions. It reproduces a broad theater sound field matching the cinemascope and wider-screen movies with an excellent dynamic range from very small to extremely large sound.
BASIC OPERATION
MOVIE
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest science fiction and special effects-featuring movies. You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation between dialog, sound effects and background music.
MOVIE
Adventure
This program is ideal for precisely reproducing the sound design of action and adventure movies. The sound field restrains reverberations but puts emphasis on reproducing a powerful space expanded widely to the left and right. The reproduced depth is also restrained relatively to ensure the separation between audio channels and the clarity of the sound.
MOVIE
Drama
This sound field features stable reverberations that match a wide range of movie genres from serious dramas to musicals and comedies. The reverberations are modest but offer an optimum 3D feeling, reproducing effects tones and background music softly but cubically around clear words and center positioning in a way that does not fatigue the listener even after long hours of viewing.
MOVIE
Mono Movie
This program is provided for reproducing monaural video sources such as a classic movie in an atmosphere of a good old movie theater. The program produces the optimum expansion and reverberation to the original audio to create a comfortable space with a certain sound depth.
English
REV.TIME REV.DELAY
45 En
Stereo playback
Note
The available parameters differ depending on the input sources and the settings of this unit.
STEREO
STEREO
2ch STEREO
Use this program to mix down multi-channel sources to 2 channels. See page 49 for details.
DIRECT
STEREO
STEREO
7ch STEREO
HiFi DSP
Use this program to output sound from all speakers. When you play back multi-channel sources, this unit downmixes the source to 2 channels, and then outputs the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties, etc.
CT LEVEL SL LEVEL
SR LEVEL SB LEVEL
PL LEVEL PR LEVEL
MUSIC ENHANCER
2ch Enhancer
The Compressed Music Enhancer feature of this unit enhances your listening experience by regenerating the missing harmonics in a compression artifact. As a result, flattened complexity due to the loss of high-frequency fidelity as well as lack of bass due to the loss of lowfrequency bass is compensated, providing improved performance of the overall sound system. Use this program to play back compression artifacts in 2-channel stereo.
Effect level
ENHANCER
MUSIC ENHANCER
7ch Enhancer
Effect level
Using sound field programs without surround speakers (Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA DSP programs without surround speakers. It creates virtual speakers to reproduce the natural sound field. When you set SUR. L/R SP to NONE (see page 71), Virtual CINEMA DSP activates automatically whenever you select a CINEMA DSP or HiFi DSP sound field program (see page 42). Note
Virtual CINEMA DSP will not activate even when SUR. L/R SP is set to NONE (see page 71) in the following cases: when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 38). when headphones are connected to the PHONES jack. when this unit is in the 7ch Stereo mode.
Enjoying multi-channel sources and sound field programs with headphones (SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel music or movie sound, including Dolby Digital and DTS sources, through ordinary headphones. SILENT CINEMA activates automatically whenever you connect headphones to the PHONES jack while listening to CINEMA DSP or HiFi DSP sound field programs (see page 42). When activated, the SILENT CINEMA indicator lights up in the front panel display. Notes
SILENT CINEMA does not activate when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 38). SILENT CINEMA is not effective when the Pure Direct (see page 48) or 2ch Stereo mode (see page 49) is selected, or when this unit is in the STRAIGHT mode (see page 47).
46 En
STRAIGHT
Deactivating the STRAIGHT mode
Press E STRAIGHT (or Q STRAIGHT) so that STRAIGHT disappears from the front panel display. The sound effect is turned back on. BASIC OPERATION English
47 En
Press C LEVEL on the remote control repeatedly to select the speaker you want to adjust.
Display Adjusted speaker Front left speaker Front right speaker Center speaker Subwoofer Surround left speaker Surround right speaker Surround back left speaker Surround back right speaker Presence left speaker Presence right speaker
FRONT L FRONT R CENTER SWFR SUR. L SUR. R SUR.B.L SUR.B.R PRNS L PRNS R y
y
The front panel display turns on momentarily when an operation is performed.
Press C TONE CONTROL on the front panel repeatedly to select the high-frequency response (TREBLE) or the low-frequency response (BASS). Rotate the D PROGRAM selector to adjust the high-frequency response (TREBLE) or the low-frequency response (BASS).
Once you press C LEVEL on the remote control, you can also select the speaker by pressing D k / n. Instead of SUR.B.L and SUR.B.R, SUR.B is displayed if SUR. B L/R SP is set to either SMLx1 or LRGx1 (see page 71). The available speaker channels differ depending on the setting of the speakers.
Notes
If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality of the surround speakers may not match. TONE CONTROL is not effective when PURE DIRECT is selected, or when MULTI CH INPUT is selected as the input source.
Press D l / h to adjust the speaker output level. Press D h to increase the value. Press D l to decrease the value. Control range: 10.0 dB to +10.0 dB
48 En
Notes
You cannot use the night listening modes in the following cases: when the Pure Direct mode (see page 48) is selected. when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 38). when headphones are connected to the PHONES jack. The night listening modes may vary in effectiveness depending on the input source and surround sound settings you use.
Press W NIGHT on the remote control repeatedly to select NIGHT:CINEMA or NIGHT:MUSIC. Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF Select NIGHT:CINEMA when watching films to reduce the dynamic range of film soundtracks and make dialog easier to hear at lower volumes. Select NIGHT:MUSIC when listening to music sources to preserve ease-of-listening for all sounds. Select OFF if you do not want to use this feature. y
When a night listening mode is selected, the NIGHT indicator lights up in the front panel display.
Press D l / h to adjust the effect level while NIGHT:CINEMA or NIGHT:MUSIC is displayed in the front panel display.
Effect.Lvl:MID
Choices: MIN, MID, MAX Select MIN for minimum compression. Select MID for standard compression. Select MAX for maximum compression. y
NIGHT:CINEMA and NIGHT:MUSIC adjustments are stored independently.
English
49 En
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use the automatic and manual preset tuning features to store up to 40 stations (A1 to E8: 8 preset station numbers in each of the 5 preset station groups). Furthermore, you can recall any preset stations and exchange the assignment of two preset stations with each other. Note
Orient the connected FM and AM antennas for the best reception.
Automatic tuning
Automatic tuning is effective when station signals are strong and there is no interference.
Manual tuning
If the signal received from the station you want to select is weak, tune into it manually. Note
Manually tuning into an FM station automatically switches the tuner to monaural reception to increase the signal quality.
1 2 3
Rotate the I INPUT selector on the front panel to select TUNER as the input source. Press 3 FM/AM to select the reception band. FM or AM appears in the front panel display. Press 7 TUNING AUTO/MANL so that the AUTO indicator lights up in the front panel display.
Lights up
1 2 3
Rotate the I INPUT selector on the front panel to select TUNER as the input source. Press 3 FM/AM to select the reception band. FM or AM appears in the front panel display. Press 7 TUNING AUTO/MANL so that the AUTO indicator disappears from the front panel display.
AUTO
FM 89.10MHz A FM 89.10MHz
No colon (:)
No colon (:)
If a colon (:) appears in the front panel display, tuning is not possible. Press 2 PRESET/TUNING to turn the colon (:) off.
Press 5 PRESET/TUNING l / h once to begin automatic tuning. When this unit is tuned into a station, the TUNED indicator lights up and the frequency of the received station is shown in the front panel display. Press 5 h to tune into a higher frequency. Press 5 l to tune into a lower frequency.
If a colon (:) appears in the front panel display, tuning is not possible. Press 2 PRESET/TUNING to turn the colon (:) off.
50 En
FM/AM tuning
Notes
Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. If the number of received stations does not reach 40 (E8), automatic preset tuning automatically stops after searching for all the available stations. Only FM stations with sufficient signal strength are stored automatically by automatic preset tuning. If the station you want to store is weak in signal strength, tune into it manually and store it as described in Manual preset tuning below. Only Radio Data System broadcasting station are stored automatically by automatic preset tuning (Europe model only).
1 2
Rotate the I INPUT selector on the front panel to select TUNER as the input source. Press 3 FM/AM to select FM as the reception band. FM appears in the front panel display. Press and hold 6 MEMORY for more than 3 seconds. The preset station number as well as the MEMORY and AUTO indicators flashes. After approximately 5 seconds, automatic presetting starts from the current frequency and proceeds toward higher frequencies.
Flashes
1 2
Tune into a station. See page 50 for tuning instructions. Press 6 MEMORY on the front panel. The MEMORY indicator flashes in the front panel display for approximately 10 seconds.
MEMORY
AUTO
MEMORY
A1:FM 89.10MHz
Flashes
When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station. y
You can specify the preset number from which this unit stores FM stations. Press 4 A/B/C/D/E and then 5 PRESET/TUNING l / h repeatedly after you perform step 3 to select the preset station number under which the first station will be stored. You can begin tuning toward lower frequencies to store FM stations automatically. Press 2 PRESET/TUNING so that the colon (:) disappears from the front panel display and then press 5 PRESET/TUNING l after pressing and holding 6 MEMORY for more than 3 seconds.
Flashes
Press 4 A/B/C/D/E repeatedly to select a preset station group (A to E) while the MEMORY indicator is flashing. The selected preset station group letter appears. Check that the colon (:) appears in the front panel display.
Flashes
MEMORY
A :FM 89.10MHz
Preset station group Colon (:)
English
51 En
FM/AM tuning
Press 5 PRESET/TUNING l / h to select a preset station number (1 to 8) while the MEMORY indicator is flashing. Press 5 h to select a higher preset station number. Press 5 l to select a lower preset station number.
Flashes
Press 5 PRESET/TUNING l / h on the front panel (or D PRESET/CH k / n on the remote control) to select the desired preset station number (1 to 8). The preset station group and number appear in the front panel display along with the station band and frequency.
MEMORY
A1:FM 89.10MHz
Preset station number
A1:FM 89.10MHz
Press 6 MEMORY while the MEMORY indicator is flashing. The station band and frequency appear in the front panel display with the preset station group and number you have selected. The MEMORY indicator disappears from the front panel display.
Select preset station E1 using 4 A/B/C/D/E and 5 PRESET/TUNING l / h on the front panel. See Selecting preset stations on the left column. Press and hold 2 EDIT for more than 3 seconds. E1 and the MEMORY indicator flash in the front panel display.
Flashes
A1:FM 89.10MHz
The displayed station has been stored as A1.
Notes
Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. The reception mode (stereo or monaural) is stored along with the station frequency.
MEMORY
E1:FM 89.10MHz
Flashes
Select preset station A5 using 4 A/B/C/D/ E and 5 PRESET/TUNING l / h. A5 and the MEMORY indicator flash in the front panel display. See Selecting preset stations on the left column.
Flashes
MEMORY
Press 4 A/B/C/D/E (or press D A/B/C/D/E l / h) to select the desired preset station group (A to E). The preset station group letter appears in the front panel display and changes each time you press the button.
A5:FM 89.10MHz
Flashes
Press 2 EDIT again. EDIT E1A5 appears in the front panel display and the assignments of the two preset stations are exchanged.
52 En
Tune into the desired Radio Data System broadcasting station. We recommend using the automatic preset tuning to tune into the Radio Data System broadcasting stations (see page 51). You can also use PTY SEEK mode to tune into the desired Radio Data System broadcasting station from the preset ones. Press G FREQ/TEXT on the remote control repeatedly to select the desired Radio Data System display mode.
PS PTY RT CT
BASIC OPERATION
Frequency display
Select PS to display the name of the Radio Data System program currently being received. Select PTY to display the type of the Radio Data System program currently being received. Select RT to display the information on the Radio Data System program currently being received. Select CT to display the current time.
English
53 En
Selecting the Radio Data System program type (PTY SEEK mode)
Use this feature to select the desired radio program by program type from the all preset Radio Data System broadcasting stations. y
Use the automatic preset tuning feature to preset Radio Data System broadcasting stations (see page 51).
Press D PRESET/CH k / n on the remote control to select the desired program type. The name of the selected program type appears in the front panel display.
POP M
Lights up
Set the operation mode selector to L SOURCE and then press B TUNER on the remote control to select TUNER as the input source. Press C BAND repeatedly to select FM as the reception band. Press G PTY SEEK MODE on the remote control to set this unit to the PTY SEEK mode. The name of the program type or NEWS flashes in the front panel display.
Program type
Descriptions News Current affairs General information Sports Education Drama Culture Science Light entertainment Popular music Rock music Middle-of-the-road music (easylistening) Light classics Serious classics Other music
2 3
NEWS
Flashes
y
To cancel the PTY SEEK mode, press G PTY SEEK MODE on the remote control again.
54 En
Press G PTY SEEK START on the remote control to start searching for all the available Radio Data System preset stations. The name of the selected program type flashes and the PTY HOLD indicator lights up in the front panel display while this unit is searching for stations.
POP M
Flashes
PTY HOLD
Lights up
y
To stop searching for stations, press G PTY SEEK START on the remote control again.
Notes
This unit stops searching for stations when a station broadcasting the selected program type is found. If the station found is not the one you desire, press G PTY SEEK START again to resume searching for another station broadcasting the same program type.
BASIC OPERATION
1 2
Tune into the desired Radio Data System broadcasting station. Make sure the EON indicator is lit in the front panel display. If the EON indicator is not lit in the front panel display, select another Radio Data System program so that the EON indicator lights up.
EON
Press G EON on the remote control repeatedly to select one of the 4 Radio Data System program types (NEWS, AFFAIRS, INFO or SPORT). The name of the selected program type appears in the front panel display.
NEWS
Lights up
y
To cancel the EON feature, press EON on the remote control repeatedly until the name of the program type disappears and EON OFF appears in the front panel display.
English
55 En
USING IPOD
Using iPod
Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-10, sold separately) connected to the DOCK terminal of this unit (see page 23), you can enjoy playback of your iPod using the supplied remote control. You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts (such as the MP3 format) stored on your iPod (see page 46). Notes
Only iPod (Click and Wheel), iPod nano, and iPod mini are supported. Some features may not be compatible depending on the model or the software version of your iPod.
y
For a complete list of the remote control functions used to control your iPod, see the iPod column in Controlling other components on page 84. For a complete list of status messages that appear in the front panel display and in the OSD, see the iPod section in Troubleshooting on page 107. Once the connection between your iPod and this unit is complete, iPod connected appears in the front panel display and the DOCK indicator lights up in the front panel display. Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the analog AUDIO OUT (REC) jacks for recording. Your iPod battery is automatically charged when your iPod is stationed in a Yamaha iPod universal dock connected to the DOCK terminal of this unit as long as this unit is turned on. You can also select whether this unit charges the battery of the stationed iPod or not when this unit is in the standby mode by selecting the STANDBY CHARGE parameter in OPTION MENU (see page 81). The DOCK indicator turns on while this unit charges the battery of the connected iPod when this unit is in the standby mode.
Controlling iPod
You can control your iPod when V-AUX is selected as the input source. The operations of your iPod can be done with the aid of the OSD of this unit (menu browse mode) or without it (simple remote mode).
Notes
Operations cannot be done with the controls on your iPod. The YAMAHA logo appears in the display window of your iPod. There are some characters that cannot be displayed in the front panel display or in the OSD of this unit. Those characters are replaced with underscores _. The Settings parameters can be changed or adjusted only in the OSD. Press ENTER on the remote control to toggle between the Settings parameter settings. You cannot browse the photos or video clips stored on your iPod in the OSD. Use the simple remote mode to enjoy watching the photos or video clips stored on your iPod.
56 En
Using iPod
Set the operation mode selector to L SOURCE and then press R DISPLAY on the remote control. The following display appears in the OSD.
iPod Playlists Artists Albums Songs Genres Composers Settings Top > > > > > > >
Press D k / n / l / h to navigate the iPod menu and then press D ENTER to begin playback of the selected song. Choices: Playlists (playlists), Artists (artists), Albums (albums), Songs (songs), Genres (genres), Composers (composers), Settings (settings) Playlists > Songs Artists > Albums > Songs Albums > Songs Songs Genres > Artists > Albums > Songs Composers > Albums > Songs Settings > Shuffle, Repeat
3 Name of the album 4 Name of the song 5 Progress bar 6 Elapsed time 7 Shuffle and repeat icons 8 h (playback), e (pausing), f (search forward) and w (search backward) 9 Remaining time BASIC OPERATION
Shuffle Shuffle Use this feature to set this unit to play songs or albums in random order. Choices: Off, Songs, Albums Select Off to deactivate this feature. Select Songs to set this unit to play songs in random order. Select Albums to set this unit to play albums in random order. y
When Shuffle is set to a setting other than Off , appears in the top right corner while songs or albums are being shuffled.
Repeat Repeat Use this feature to set this unit to repeat one song or a sequence of songs. Choices: Off, One, All Select Off to deactivate this feature. Select One to set this unit to repeat one song. Select All to set this unit to repeat a sequence of songs. y
When Repeat is set to a setting other than Off , or appears in the top right corner while one song or a sequence of songs are being repeated.
1 All
English
57 En
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components. Caution The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the following considerations and adjustments need to be made. To play DTS-encoded DVDs and CDs (when using a digital audio connection) on your DTS-compatible player, follow its operating instructions to make a setting so that the analog signal will be output from the player. Notes
When this unit is set to the standby mode, you cannot record between other components connected to this unit. TONE CONTROL (see page 48) and VOLUME settings, the speaker level (see page 72) and the sound field programs (see page 42) do not affect recorded material. The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded. Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Likewise, analog signals input at the AUDIO IN jacks are not output at the DIGITAL OUTPUT jack. Therefore, if your source component is connected to provide only digital or analog signals, you can only record digital or analog signals. A given input source is not output on the same OUT (REC) channel. S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing video signals input from a video source component that provides only an S-video or a composite video signal, you can only record an S-video or a composite video signal on your VCR. The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording. Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals.
1 2
Turn on all the connected components. Rotate the I INPUT selector (or press one of the input selector buttons (B)) to select the source component you want to record from.
3 4
Start playback on the selected source component or select a broadcast station. Start recording on the recording component.
58 En
Press D k / n to select the desired sound field parameter and then D l / h to change the selected sound field parameter value.
PARAMETER
Cursor
MOVIE Sci-Fi 1/2 PRO LOGIC DSP LEVEL;;;;0dB P.INIT.DLY;;16ms P.ROOM.SIZE;;1.0 S.INIT.DLY;;20ms [RETURN]:STATUS
y
For details about the function and control range of each sound field parameter, see page 61. When you set a sound field parameter to a value other than the initial factory settings, an asterisk mark (*) appears by the sound field parameter name in the OSD. The available sound field parameters for some of the sound field programs may be displayed on more than one page in the OSD. In this case, press D k / n to scroll through pages. If you press and hold D l / h to change the sound field parameter value, the initial factory settings are shown momentarily in the front panel display. Use the PARAM. INI feature in OPTION MENU to initialize the parameters of each sound field program within a sound field program group (see page 80). You can select the amount of time that the current status is displayed in the OSD by using the OSD-AMP parameter in OPTION MENU (see page 79).
1 2
Turn on the video monitor connected to this unit. Set the operation mode selector to L AMP and then press R DISPLAY on the remote control. The following status screen appears in the OSD.
STATUS VOL:-40.0dB MOVIE Sci-Fi INPUT: A.SEL: DVD HDMI
ADVANCED OPERATION
NIGHT: OFF
5 3
Press one of the sound field program selector buttons (U) repeatedly to select the desired sound field program you want to adjust.
English
59 En
Adjusting the vertical dialogue position (DIALG.LIFT) Use this feature to adjust the vertical position of the dialogues in movies. The ideal position of the dialogues is at the center of the video monitor screen.
Each sound field program has some parameters defining the characteristics of the program. To customize the selected sound field program, adjust DSP LEVEL and/ or DIALG.LIFT first, and then try other parameters. Adjusting the effect sound level of the sound field programs (DSP LEVEL) Sound field programs add effect sounds (DSP effect sounds) to the original source sound to create sound field in the listening room. Use the DSP LEVEL parameter to adjust the level of the effect sounds.
The ideal dialogue position.
If the dialogues are heard at the lower position of the video monitor screen, increase the value of DIALG.LIFT.
Move up to the ideal dialogue position. The DSP effect sound level is low. The DSP effect sound level is high.
Adjust DSP LEVEL as follows: Increase the value of DSP LEVEL when The effect sound of the selected sound field program is too weak. You cannot recognize any difference between the sound field programs. Decrease the value of DSP LEVEL when The sound is vague. You feel that the additional sound effect is excessive. Control range: 6 dB to +3 dB
Choices: 0, 1, 2, 3, 4, 5 0 (initial setting) is the lowest position, and 5 is the highest position. Notes
DIALG.LIFT is only available only EXTRA SP ASSIGN is set to PRESENCE (see page 72). You cannot move the dialogue position down from the initial dialogue position.
60 En
Time Delay
Time
ADVANCED OPERATION
Reflection face
Small value = 1 ms
Large value = 99 ms
English
61 En
Features Room size. Presence, surround, and surround back room size. Adjusts the apparent size of the surround sound field. The larger the value, the larger the surround sound field becomes. As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between the original reflected sound and the subsequent reflections. By controlling the time between the reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from one to two doubles the apparent length of the room. y When you adjust the room size parameters, we also recommend adjusting the corresponding initial delay parameters likewise. This adjustment is especially effective for the CINEMA DSP programs. Control range: 0.1 to 2.0
Source sound Early reflections Time
Level
Level
Level
Time
Liveness. Surround and surround back sound field liveness. Adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the early reflections decay. The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces is referred to as dead, while a room with highly reflective surfaces is referred to as live. This parameter lets you adjust the early reflection decay rate and thus the liveness of the room. Control range: 0 to 10
Source sound Live Level Level Level Time Dead Time
Time
Small value = 0
Large value = 10
62 En
Features Reverberation time. Adjusts the amount of time taken for the dense, subsequent reverberation sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment over an extremely wide range. Set a longer reverberation time for dead sources and listening room environments, and a shorter time for live sources and listening room environments. Control range: 1.0 to 5.0 s
REV.TIME
Reverberation
Reverberation
60 dB
60 dB
60 dB
REV.TIME
REV.DELAY
Reverberation delay. Adjusts the time difference between the beginning of the direct sound and the beginning of the reverberation sound. The larger the value, the later the reverberation sound begins. A later reverberation sound makes you feel as if you are in a larger acoustic environment.
ADVANCED OPERATION
(dB)
Level
Source sound
REV.LEVEL
Reverberation level. Adjusts the volume of the reverberation sound. The larger the value, the stronger the reverberation becomes. Control range: 0 to 100%
Level
Source sound
REV. LEVEL
English
Time
63 En
Features 2-channel stereo direct. Bypasses the decoders and the DSP processors of this unit for pure hi-fi stereo sound when playing 2-channel analog sources. Choices: AUTO, OFF y Select AUTO to bypass the decoders, the DSP processors and the tone control circuitry only when BASS and TREBLE are set to 0 dB (see page 48). Select OFF not to bypass the decoders, the DSP processors and the tone control circuitry when BASS and TREBLE are set to 0 dB. When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2 channels and output from the front left and right speakers. The low-frequency signals input from the front left and right speakers are redirected to the subwoofer in the following cases: LFE/BASS OUT is set to BOTH (see page 70). FRONT SP is set to SMALL (see page 71) and LFE/BASS OUT is set to SWFR (see page 70).
7ch Stereo CT LEVEL SL LEVEL SR LEVEL SB LEVEL PL LEVEL PR LEVEL 2ch Enhancer 7ch Enhancer
7-channel stereo center, surround left, surround right, surround back, presence left and presence right levels. Adjusts the volume level of each channel in the 7-channel stereo mode. The available parameters differ depending on the setting of the speakers. Control range: 0 to 100%
2-channel and 7-channel Compressed Music Enhancer effect level. The high-frequency signals of some sources may be emphasized too much. In this case, set the effect level to LOW. Choices: HIGH, LOW Select HIGH for a high effect level. Select LOW for a low effect level.
Selecting decoders
Selecting decoders for 2-channel sources (surround decode mode)
Use this feature to play back sources with selected decoders. You can play back 2-channel sources on multichannels. Set the operation mode selector to L AMP and then press U SUR. DECODE repeatedly on the remote control to select the desired surround decoder. You can select from the following modes depending on the type of source you are playing and your personal preference. y
You can change the decoder parameter settings. Press DISPLAY and then D k / n repeatedly on the remote control to select the desired decoder parameter. You can change the value of the selected parameter by pressing D l / h repeatedly on the remote control.
PRO LOGIC
64 En
Decoder descriptions
Remote control button Category of the program Name of the program
SUR.DECODE
SURROUND DECODE
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx decoder is not
available when SUR. B L/R SP is set to NONE (see page 71).
PANORAMA DIMENSION CENTER WIDTH
Program description
SUR.DECODE
SURROUND DECODE
PRO LOGIC
SURROUND DECODE
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for movie sources. The Pro Logic IIx decoder is not available when
SUR. B L/R SP is set to NONE (see page 71).
SUR.DECODE
SURROUND DECODE
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx decoder is not available when
SUR. B L/R SP is set to NONE (see page 71).
PANORAMA
SUR.DECODE
DIMENSION
CENTER WIDTH
SURROUND DECODE
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for game sources. The Pro Logic IIx decoder is not available when
SUR. B L/R SP is set to NONE (see page 71).
SUR.DECODE
SURROUND DECODE
Neo:6 Cinema
SURROUND DECODE
Neo:6 Music
y
When you select the surround decode mode for Dolby Digital, DTS or DTS 96/24 sources, this unit automatically selects SURROUND DECODE Dolby Digital, SURROUND DECODE DTS or SURROUND DECODE DTS 96/24 program.
English
65 En
PRO LOGIC IIx Music PRO LOGIC II Music PANORAMA PRO LOGIC IIx Music PRO LOGIC II Music DIMENSION
Pro Logic IIx Music and Pro Logic II Music center width. Moves the center channel output completely towards the center speaker or towards the front left and right speakers. A larger value moves the center channel output towards the front left and right speakers. Control range: 0 (center channel sound is output only from the center speaker) to 7 (center channel sound is output only from the front left and right speakers) Initial setting: 3
DTS Neo:6 Music center image. Adjusts the front left and right channel output relative to the center channel to make the center channel more or less dominant as necessary. Control range: 0.0 to 1.0 Initial setting: 0.3
66 En
Auto setup AUTO SETUP Use this feature to automatically adjust speaker and system parameters (see page 28). Manual setup MANUAL SETUP Use this feature to manually adjust speaker and system parameters.
Sound menu 1 SOUND MENU Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or compensate for video signal processing delays when using LCD monitors or projectors.
Parameter Features
Selects the size of each speaker, the speakers for low-frequency signal output, the crossover frequency, and the assignment of the EXTRA SP terminal. Adjusts the output level of each speaker. Adjusts the distance of each speaker. Adjusts the tonal quality of the center speaker. Adjusts the output level of the LFE channel for Dolby Digital or DTS signals. Adjusts the dynamic range of Dolby Digital or DTS signals. Adjusts the muting level, audio delay, maximum volume level and initial volume level. Selects the component to play back HDMI audio signals. Selects the mode of the decoders for the 6.1/7.1-channel playback.
Page 70 72 73 73 74 74 74 75 75
A)SPEAKER SET B)SPEAKER LEVEL C)SP DISTANCE D)EQUALIZER E)LFE LEVEL F)DYNAMIC RANGE G)AUDIO SET H)HDMI SET I)EXTD SUR.
ADVANCED OPERATION
Input menu 2 INPUT MENU Use this menu to manually reassign the input/output jacks, select the input mode or rename the input source.
Parameter Features
Assigns the input/output jacks of this unit according to the component to be used. Changes the name of the input source. Adjusts the output volume of each input source. Selects the input mode for the sources connected to the DIGITAL INPUT jacks on the rear panel of this unit. Sets the input channel numbers and other parameters of the input multi channel.
Page 76 77 78 78 78
A)I/O ASSIGNMENT B)INPUT RENAME C)VOLUME TRIM D)DECODER MODE E)MULTI CH SET
English
67 En
Option menu 3 OPTION MENU Use this menu to manually adjust the optional system parameters.
Parameter Features
Adjusts the brightness of the display and converts video signals. Locks sound field program parameters and other SET MENU settings. Designates the default audio input jack select setting mode for the input sources when you turn on the power of this unit. Initializes the parameters of a group of sound field programs. Adjusts the Zone 2 parameters. Selects whether this unit charges the battery of the connected iPod or not when this unit is in the standby mode.
Page 79 80 80 80 80 81
A)DISPLAY SET B)MEMORY GUARD C)AUDIO SELECT D)PARAM.INI E)ZONE 2 SET F)DOCK SET
68 En
Press D k / n repeatedly and then press D ENTER to select and enter the desired menu. The following displays are examples where SOUND MENU is selected.
MANUAL SETUP 1 SOUND MENU . A)SPEAKER SET B)SPEAKER LEVEL C)SP DISTANCE D)EQUALIZER E)LFE LEVEL [ ]/[ ]:Up/Down [ENTER]:Enter 1/2 MANUAL SETUP 1 SOUND MENU . F)DYNAMIC RANGE G)AUDIO SET H)HDMI SET I)EXTD SUR. [ ]/[ ]:Up/Down [ENTER]:Enter 2/2
Set the operation mode selector to L AMP and then press N SET MENU to enter SET MENU. The top SET MENU display appears in the OSD.
SET MENU . ;AUTO SETUP ;MANUAL SETUP .A;SIGNAL INFO [ ]/[ ]:Up/Down [ENTER]:Enter
Press D k / n repeatedly and then press D ENTER to select and enter the desired submenu. The following display is an example where LFE LEVEL is selected.
SOUND MENU E)LFE LEVEL
Press D k / n to select MANUAL SETUP and then D ENTER to enter MANUAL SETUP. The MANUAL SETUP display appears in the OSD.
ADVANCED OPERATION
5
MANUAL SETUP . 1 SOUND MENU 2 INPUT MENU 3 OPTION MENU
Press D k / n to select the desired parameter and then D l / h to change the parameter settings. Press N SET MENU to exit from SET MENU.
6
[ ]/[ ]:Up/Down [ENTER]:Enter
English
69 En
1 SOUND MENU
Use this feature to manually adjust speaker settings or compensate for video signal processing delays when using LCD monitors or projectors. Most of the SOUND MENU parameters are set automatically when you run AUTO SETUP (see page 28).
MANUAL SETUP 1 SOUND MENU . A)SPEAKER SET B)SPEAKER LEVEL C)SP DISTANCE D)EQUALIZER E)LFE LEVEL [ ]/[ ]:Up/Down [ENTER]:Enter 1/2 MANUAL SETUP 1 SOUND MENU . F)DYNAMIC RANGE G)AUDIO SET H)HDMI SET I)EXTD SUR. [ ]/[ ]:Up/Down [ENTER]:Enter 2/2
FRONT B speakers setting FRONT B The FRONT B parameter is available only when you set EXTRA SP ASSIGN to FRONT B. Use this feature to select the location of the FRONT B speakers. Choices: FRONT, ZONE B Select FRONT to turn FRONT A and B on or off when the FRONT B speakers are set in the main room. Select ZONE B if the FRONT B speakers are set in another room. If FRONT A is turned off and FRONT B is turned on, all the speakers including the subwoofer in the main room are muted and this unit outputs sound at the FRONT B terminals only. Notes
If you connect headphones to the PHONES jack of this unit, the sound is output from both the headphones and the EXTRA SP terminals when FRONT B is set to ZONE B. If a DSP program is selected when FRONT B is set to ZONE B, this unit automatically enters the Virtual CINEMA DSP mode (see page 46).
Extra speakers assignment EXTRA SP ASSIGN Selects the function of the speakers connected to the EXTRA SP terminals. Choices: FRONT B, ZONE2, PRESENCE, NONE When you use the alternative front speaker system (see page 38) Select FRONT B. When you use the Zone 2 speakers (see page 96) Select ZONE2 to set the function of the speakers to the Zone 2 speakers. When you use the presence speakers (see page 12) Select PRESENCE to set the function of the speakers to the presence speakers. When you do not use the EXTRA SP terminals Select NONE to deactivate the EXTRA SP terminals. Notes
This parameter shares the value with the EXTRA SP ASSIGN parameter in AUTO SETUP. If you select ON in BI-AMP (see page 101), you cannot select PRESENCE or ZONE2 in EXTRA SP ASSIGN. After changing the EXTRA SP ASSIGN setting, carry out AUTO SETUP again (see page 28).
70 En
Presence/Surround back channel priority PRIORITY The PRIORITY parameter is available only when you set EXTRA SP ASSIGN to PRESENCE. Use this feature to prioritize either the presence or the surround back speakers when playing sources that contain surround back channel signals using the CINEMA DSP sound field programs. Choices: PRNS, SUR. B Select PRNS to use the presence speakers even when surround back channel signals are input. The signals for the surround back channels will be output from the surround speakers. Select SUR. B to use the surround back speakers when surround back channel signals are detected in a CINEMA DSP program. The presence channel signals are output from the front speakers.
Woofer section of a speaker is 16 cm (6.5 in) or larger: large Woofer section of a speaker is smaller than 16 cm (6.5 in): small Front speakers FRONT SP Choices: SMALL, LARGE
SOUND MENU FRONT SP
SMALL
>LARGE
NONE >SML
LRG
When the front speakers are large Select LARGE (large). When the front speakers are small Select SMALL (small). Note
When LFE/BASS OUT is set to FRNT (see page 70), you can select only LARGE in FRONT SP. If the value of FRONT SP is set to a setting other than LARGE in advance, this unit automatically changes the value to LARGE.
When the surround speakers are large Select LRG (large). When the surround speakers are small Select SML (small). When you do not use the surround speakers Select NONE (none). This unit is set to the Virtual CINEMA DSP mode (see page 46), and SUR. B L/R SP is automatically set to NONE. Surround back left/right speakers SUR. B L/R SP Choices: NONE, SMLx1, SMLx2, LRGx1, LRGx2
SOUND MENU
ADVANCED OPERATION
SUR.B L/R SP
LRGx1
When the center speaker is large Select LRG (large). When the center speaker is small Select SML (small). When you do not use the center speaker Select NONE (none). The center channel signals are directed to the front left and right speakers.
When the surround back left and right speakers are large Select LRGx2 (large x 2). When the single surround back speaker is large Select LRGx1 (large x 1). When the surround back left and right speakers are small Select SMLx2 (small x 2). When the single surround back speaker is small Select SMLx1 (small x 1). When you do not use the surround back speakers Select NONE (none). The surround back channel signals are directed to the surround left and right speakers. English
71 En
LFE/Bass out LFE/BASS OUT Use this feature to select the speakers that output the LFE (low-frequency effect) and the low-frequency signals. Choices: SWFR, FRNT, BOTH
SOUND MENU LFE/BASS OUT
Subwoofer phase SUBWOOFER PHASE Use this feature to switch the phase of your subwoofer if bass sounds are lacking or unclear. Choices: NORMAL, REVERSE
SOUND MENU SUBWOOFER PHASE
SWFR FRNT>BOTH
>NORMAL
REVERSE
When a subwoofer is connected to this unit and you want to get natural bass sound Select SWFR (subwoofer). The LFE signals as well as the low-frequency signals of other speakers set to SML (or SMALL) are directed to the subwoofer. When a subwoofer is connected to this unit and you want to get rich bass sound Select BOTH (both). The low-frequency signals of any source are output from the subwoofer. The LFE signals as well as the low-frequency signals of other speakers set to SML (or SMALL) are directed to the subwoofer. The low-frequency signals of the front left and right channels are directed to the front left and right speakers and the subwoofer regardless of the FRONT SP setting. When you do not use a subwoofer Select FRNT (front). The LFE signals, the low-frequency signals of the front left and right channels, and the low-frequency signals of other speakers set to SML (or SMALL) are all directed to the front left and right speakers regardless of the FRONT SP setting. Bass crossover CROSSOVER Use this feature to select the crossover frequency of all the speakers set to SML (or SMALL) or to NONE in SPEAKER SET (see page 71). All frequencies below the selected frequency will be sent to the subwoofer or to the speakers set to LRG (or LARGE) in SPEAKER SET (see page 71). Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz, 120Hz, 160Hz, 200Hz
SOUND MENU CROSSOVER
Select NORMAL if you do not want to reverse the phase of your subwoofer. Select REVERSE to reverse the phase of your subwoofer.
Speaker level
B)SPEAKER LEVEL Use this feature to manually adjust the output level of each speaker. Control range: 10.0 to +10.0 dB Control step: 0.5 dB Initial setting: 0.0 dB
SOUND MENU B)SPEAKER LEVEL 1/2 -__________+ FL;;;;;;;;;; FR;;;;;;;;;; C;;;;;;;;;; SWFR;;;;;;;;;;
SPEAKER LEVEL
Adjusted speaker Front left speaker Front right speaker Center speaker Subwoofer Surround left speaker Surround right speaker Surround back right speaker Surround back left speaker Presence left speaker Presence right speaker
FREQ;;;80Hz
The available speaker channels differ depending on the setting of the speakers. Instead of SBL and SBR, SB is displayed if SUR. B L/R SP is set to either SMLx1 or LRGx1 (see page 71).
72 En
Equalizer D)EQUALIZER
Use this feature to select the parametric equalizer or the graphic equalizer. Equalizer type select EQ TYPE SELECT Use this feature to select the type of equalizer. Choices: AUTO PEQ, CENTER GEQ, EQ OFF
SOUND MENU D)EQUALIZER . EQ TYPE SELECT CENTER GEQ
Unit UNIT Choices: meters (m), feet (ft) Initial setting: [U.S.A. and Canada models]: feet (ft) [Other models]: meters (m) Select meters to adjust speaker distances in meters. Select feet to adjust speaker distances in feet. Speaker distances Control range: 0.30 to 24.00 m (1.0 to 80.0 ft) Control step: 0.10 m (0.5 ft) Initial setting: FRONT L/FRONT R/CENTER/SWFR/SUR. L/SUR. R/ PRNS L/PRNS R: 3.00 m (10.0 ft) SB L/SB R: 2.10 m (7.0 ft)
SP DISTANCE Adjusted speaker Front left speaker Front right speaker Center speaker Subwoofer Surround left speaker Surround right speaker Surround back left speaker Surround back right speaker Presence left speaker Presence right speaker
Select AUTO PEQ to use the parametric equalizer adjusted in AUTO SETUP (see page 28). Select CENTER GEQ to adjust the built-in 5-frequency band graphic equalizer so that the tonal quality of the center speaker matches that of the front left and right speakers. Press D k / n to display the graphic equalizer screen. Select EQ OFF to deactivate the equalizing feature. Note
When you carry out AUTO SETUP in advance (see page 28), AUTO PEQ is automatically selected as the default setting.
ADVANCED OPERATION
Use this feature to make adjustments for CENTER GEQ while listening to a test tone. Choices: OFF, ON Select OFF to stop test tones and output the currently selected source component. Select ON to output test tones from the center and front left speakers.
The available speaker channels differ depending on the setting of the speakers. Instead of SB L and SB R, SB is displayed if SUR. B L/ R SP is set to either SMLx1 or LRGx1 (see page 71).
English
73 En
Center graphic equalizer CENTER GEQ Use to match the tonal quality of the center speaker with that of the front left and right speakers. You can adjust 5 frequency bands (100 Hz, 300 Hz, 1 kHz, 3 kHz and 10 kHz). Control range: 6.0 to +6.0 dB Control step: 0.5 dB
SOUND MENU TEST >OFF ON -______+ . 100Hz ;;;;;; 300Hz ;;;;;; 1kHz ;;;;;; 3kHz ;;;;;; 10kHz ;;;;;; [ ]/[ ]:Up/Down [p]/[[]:Adjust
Dynamic range F)DYNAMIC RANGE Use this feature to select the amount of dynamic range compression to be applied to your speakers or headphones. This setting is effective only when this unit is decoding Dolby Digital and DTS signals. Choices: MIN, STD, MAX Select MIN (minimum) if you regularly listen at low volume levels. Select STD (standard) for general use. Select MAX (maximum) to preserve the greatest amount of dynamic range.
SOUND MENU F)DYNAMIC RANGE
y
Press D k / n to select a frequency band and D l / h to adjust the selected frequency band.
Note
The CENTER GEQ parameter can be adjusted only when CENTER GEQ is selected in EQ TYPE SELECT.
Speaker SP Adjusts the speaker compression. Headphone HP Adjusts the headphone compression.
Audio settings G)AUDIO SET Use this feature to adjust the overall audio settings of this unit.
SOUND MENU G)AUDIO SET . MUTING TYPE;FULL A.DELAY;;;;;;0ms MAX VOL.;+16.5dB INI.VOL.;;;;;OFF [ ]/[ ]:Up/Down [p]/[[]:Select
Speaker SPEAKER Adjusts the speaker LFE level. Headphone HEADPHONE Adjusts the headphone LFE level. Note
Depending on the settings of LFE/BASS OUT (see page 70), some signals may not be output at the SUBWOOFER OUTPUT jack.
Muting type MUTING TYPE Use this feature to adjust how much the mute function reduces the output volume (see page 40). Choices: FULL, 20dB Select FULL to completely mute all the audio output. Select 20dB to reduce the current volume by 20 dB. Audio delay AUDIO DELAY Use this feature to delay the sound output and synchronize it with the video image. This may be necessary when using certain LCD monitors or projectors. Control range: 0 to 160 ms Control step: 1 ms
74 En
Maximum volume MAX VOL. Use this feature to set the maximum volume level in the main zone. This feature is useful to avoid the unexpected loud sound by mistake. For example, the original volume range is 16.5 dB to 80.0 dB. However, when MAX VOL. is set to 5.0 dB, the volume range becomes 5.0 dB to 80.0 dB. Control range: 16.5 dB, 15.0 dB to 30.0 dB Control step: 5.0 dB Notes
When this unit is in the auto setup procedure, the volume level is automatically set to 0 dB regardless of the current MAX VOL. setting. The MAX VOL. setting takes priority over the Initial Volume setting. For example, if INI VOL. is set to 20.0 dB and MAX VOL. is set to 30.0 dB, the volume level is automatically set to 30.0 dB when you turn on the power of this unit next time. Use MAX VOL. in ZONE2 SET to set the initial volume level in Zone 2 (see page 81).
Note
The HDMI video signals input at the HDMI IN 1 or HDMI IN 2 jack of this unit are always output at the HDMI OUT jack of this unit.
[p]/[[]:Select
Initial volume INI VOL. Use this feature to set the volume level of the main zone when the power of this unit is turned on. Choices: Off, 80.0 dB to +16.5 dB Control step: 0.5 dB Notes
The MAX VOL. setting takes priority over the INI VOL. setting. Use INI VOL. in ZONE2 SET to set the initial volume level in Zone 2 (see page 81).
Mode MODE Use this feature to select the mode of the decoder driving. Choices: AUTO, ON, OFF Select AUTO to activate the optimum decoder to play back the signal in 6.1/7.1 channels when a signal flag that can be recognized by this unit is input. Select ON to play back multi-channel sources using the selected decoder type in TYPE. Select OFF not to use the decoders to create 6.1/7.1 channels. Decoder type TYPE
SOUND MENU I)EXTD SUR. . MODE;;;;;;;;;;ON TYPE;;;PLI IxMovie [ ]/[ ]:Up/Down [p]/[[]:Select
ADVANCED OPERATION
Use this feature to select the decoders used to play back multi-channel sources when you select ON in MODE. Choices: PLIIxMovie, PLIIxMusic, EX/ES, EX Select PLIIxMovie to play back Dolby Digital or DTS signals in 7.1 channels using the Pro Logic IIx movie decoder. Select PLIIx Music to play back Dolby Digital or DTS signals in 6.1/7.1 channels using the Pro Logic IIx music decoder. Select EX/ES to play back Dolby Digital or DTS signals in 6.1/7.1 channels using the Dolby Digital EX or DTS-ES decoder. Select EX to play back Dolby Digital or DTS signals in 6.1/7.1 channels using the Dolby Digital EX decoder.
Support audio SUPPORT AUDIO Use this feature to select whether to play back HDMI audio signals on this unit or on another HDMI component connected to the HDMI OUT jack on the rear panel of this unit. Choices: RX-V661, OTHER Select RX-V661 to play back HDMI audio signals on this unit. The HDMI audio signals input at the HDMI IN jacks of this unit are not output to the HDMI component connected to the HDMI OUT jack on the rear panel of this unit. Select OTHER to play back HDMI audio signals on another HDMI component connected to the HDMI OUT jack.
English
75 En
y
Use this feature to activate the desired decoder manually when this unit cannot detect the signal flag encoded to the input sources correctly.
2 INPUT MENU
Use this menu to reassign the input/output jacks, select the input mode or rename the input source.
MANUAL SETUP 2 INPUT MENU . A)I/O ASSIGNMENT B)INPUT RENAME C)VOLUME TRIM D)DECODER MODE E)MULTI CH SET [ ]/[ ]:Up/Down [ENTER]:Enter
Notes
The available decoders vary depending on the setting of the speakers and the input sources. 6.1/7.1-channel playback is not possible in the following cases: when SUR. L/R SP (see page 71) or SUR. B L/R SP (see page 71) is set to NONE. when the component connected to the MULTI CH INPUT jacks is being played. when the source being played does not contain surround left and right channel signals. when a Dolby Digital KARAOKE source is being played. when the stereo playback, Compressed Music Enhancer (see page 46) or Pure Direct (see page 48) mode is selected. when BI-AMP is set to ON (see page 101). When this unit is turned off, this setting will be reset to AUTO.
Input/output assignment
A)I/O ASSIGNMENT Use this feature to assign the input/output jacks according to the component to be used if the initial settings of this unit do not correspond to your needs. Change the following parameters to reassign the respective jacks and effectively connect more components. Once the input/output jacks are reassigned, you can select the corresponding component by using the INPUT selector on the front panel (or the input selector buttons on the remote control). y
The input source name in parentheses indicates the default assigned input source.
For COMPONENT VIDEO jacks A, B and C CMPNT-V INPUT Choices: [A] DVD, DTV/CBL, V-AUX, DVR, VCR [B] DVD, DTV/CBL, V-AUX, DVR, VCR [C] DVD, DTV/CBL, V-AUX, DVR, VCR
INPUT MENU CMPNT-V INPUT . [A];;;;; DVD ( DVD ) [B];;;;;DTV/CBL (DTV/CBL)) [C];;;;; DVR ( DVR )
76 En
For OPTICAL OUTPUT jack 1 OPTICAL OUT Choices: (1) PHONO, CD, MD/CD-R, DVD, DTV/CBL, V-AUX, VCR, DVR
INPUT MENU OPTICAL OUT . (1);;;;;MD/CD-R (MD/CD-R )
For HDMI IN jacks 1 and 2 HDMI IN Choices: [IN1] DVD, DTV/CBL, V-AUX, DVR, VCR [IN2] DVD, DTV/CBL, V-AUX, DVR, VCR
INPUT MENU HDMI IN . [IN1];;; DVD ( DVD ) [IN2];;;DTV/CBL (DTV/CBL))
Use this feature to change the name of the input source that appears in the OSD and in the front panel display.
INPUT MENU B)INPUT RENAME DVD -> MY DVD
For OPTICAL INPUT jacks 2, 3 and 4 OPTICAL IN Choices: (2) PHONO, CD, MD/CD-R, DVD, DTV/CBL, DVR, VCR (3) PHONO, CD, MD/CD-R, DVD, DTV/CBL, DVR, VCR (4) PHONO, CD, MD/CD-R, DVD, DTV/CBL, DVR, VCR
INPUT MENU OPTICAL IN . (2);;;;;MD/CD-R (MD/CD-R ) (3);;;;; DVD ( DVD ) (4);;;;;DTV/CBL (DTV/CBL )
y
This feature is useful when you change the input or output assignment for digital jacks and component video input jacks. You can only rename DOCK when iPod is stationed in the Yamaha Universal Dock connected to this unit.
ADVANCED OPERATION
Press one of the input selector buttons (B) on the remote control to select the input source you want to change the name of. Press D l / h to place the _ (underscore) under the space or the character you want to edit. Press D k / n to select the character you want to use and then press D l / h to move to the next space. Notes
For COAXIAL INPUT jacks 5 and 6 COAXIAL IN Choices: (5) PHONO, CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR, VCR (6) PHONO, CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR, VCR
INPUT MENU COAXIAL IN . (5);;;;; CD ( CD ) (6);;;;; DVD ( DVD ) (4);;;;;DTV/CBLTA
You can use up to 8 characters for each input. Press D n to change the character in the following order, or press D k to go in the reverse order: A to Z, 0 to 9, a to z, symbols (#, *, , +, etc.), space.
4 5
Repeat steps 1 through 3 to rename each input source. Press D ENTER on the remote control to exit from INPUT RENAME.
English
77 En
Volume Trim C)VOLUME TRIM Use this feature to adjust the output level of each input source. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. Choices: TUNER, PHONO, CD, MD/CD-R, DVD, DTV/ CBL, VCR, DVR, V-AUX, DOCK, MULTI CH Control range: 6.0 to +6.0 dB Control step: 0.5 dB Initial setting: 0.0 dB
INPUT MENU C)VOLUME TRIM MY DVD DVD -> 0.0dB [[]/[[]:Adjust [RETURN]:Exit
y
You can adjust the value for DOCK only when iPod is stationed to the Yamaha Universal Dock connected to this unit. The default name (DVD in the display example above) and the new name (MY DVD) of the selected input source appears in the OSD.
BGV BGV Use this feature to select the video source played in the background of the sources input from the MULTI CH INPUT jacks. Choices: DVD, DTV/CBL, V-AUX, DVR, VCR, LAST, OFF Select LAST to set this unit to automatically select the last selected video source as the background video source. Select OFF to set this unit not to play the video source in the background. Input channels INPUT CH Use this setting to select the number of channels input from an external decoder. Choices: 6CH, 8CH Select 6CH if you input 6-channel signals. Select 8CH if you input 8-channel signals. Front input FRONT
INPUT MENU E)MULTI CH SET
Decoder select mode Use this feature to designate the default decoder mode for the input sources connected to the DIGITAL INPUT jacks when you turn on the power of this unit. Choices: AUTO, LAST Select AUTO to if you want this unit to automatically detect the type of input signals and select the appropriate decoder mode. Select LAST to if you want this unit to automatically select the last decoder mode used for the connected input source. DTS decoder prioritize setting Choices: AUTO, DTS Select AUTO if you want this unit to automatically detect input signal types and select the appropriate input mode. Select DTS if you want this unit to select DTS as the input mode.
If you selected 8CH in INPUT CH, you can select the analog jacks at which the front signals from an external decoder will be input. Choices: CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR, VCR y
See page 22 for the connection information.
Note
The FRONT parameter appears only when you set INPUT CH to 8CH.
78 En
3 OPTION MENU
Use this menu to adjust the optional system parameters.
MANUAL SETUP 3 OPTION MENU . A)DISPLAY SET B)MEMORY GUARD C)AUDIO SELECT D)PARAM. INI [ ]/[ ]:Up/Down [ENTER]:Enter 1/2 MANUAL SETUP 3 OPTION MENU . E)ZONE2 SET F)DOCK SET 2/2
OSD shift OSD SHIFT Use this feature to adjust the vertical position of the OSD. Control range: 5 (upward) to +5 (downward) Control step: 1 Initial setting: 0 Press D l to raise the position of the OSD. Press D h to lower the position of the OSD. Source feature OSD display time OSD-SOURCE Use this feature to set the amount of time to display the iPod menu in the OSD after you perform a certain operation. Choices: ON, 10s, 30s Select ON to display the OSD continuously during an operation. Select 10s to turn off the OSD 10 seconds after you perform a certain operation. Select 30s to turn off the OSD 30 seconds after you perform a certain operation. Amplifier function OSD display time OSD-AMP Use this feature to set the amount of time to display the status and sound field parameters information screen after you perform a certain operation. Choices: ON, 10s, 30s Select ON to display the OSD constantly during an operation. Select 10s to turn off the OSD 10 seconds after you perform a certain operation. Select 30s to turn off the OSD 30 seconds after you perform a certain operation. Front panel display scroll FL SCROLL Use this feature to set whether to display the information (such as a song title or a channel name) in the front panel display in a continuous manner or by the first 14 alphanumeric characters after scrolling all characters once when DOCK is selected as the input source. Choices: CONT, ONCE Select CONT to display the operation status in the front panel display in a continuous manner. Select ONCE to display the operation status in the front panel display by the first 14 alphanumeric characters after scrolling all characters once.
Dimmer DIMMER Use this feature to adjust the brightness of the front panel display. Control range: 4 to 0 Control step: 1 Press D l to make the front panel display dimmer. Press D h to make the front panel display brighter. Video conversion VIDEO CONV. Use this feature to set whether to convert the video signals input at the VIDEO, S VIDEO and COMPONENT VIDEO jacks. Choices: ON, OFF Select ON to convert composite, S-video and component video signals interchangeably. Select OFF not to convert any signals. Notes
This unit does not convert 480 line video signals and 576 line video signals interchangeably. The converted video signals are only output at the MONITOR OUT jacks. When recording a video source, you must make the same type of video connections between each component. When composite video or S-video signals from a VCR are converted to component video signals, the picture quality may suffer depending on your VCR. Unconventional signals input at the composite video or S-video jacks cannot be converted or may be output abnormally. In such cases, set VIDEO CONV. to OFF. When non-standard video signals (such as video signals from a game console) are input, this unit may not convert the signals even if you set VIDEO CONV. to ON.
79 En
Memory guard B)MEMORY GUARD Use this feature to prevent accidental changes to DSP program parameter values and other system settings. Choices: OFF, ON
OPTION MENU B)MEMORY GUARD >OFF ON
[[]/[[]:Select [ENTER]:Return
Select OFF to turn off the MEMORY GUARD feature. Select ON to protect: sound field program parameters all SET MENU items all speaker levels SCENE template parameters Note
When MEMORY GUARD is set to ON, you cannot select and adjust any other SET MENU items.
Audio select
C)AUDIO SELECT Use this feature to designate the default audio input jack select setting for the input sources when you turn on the power of this unit. Choices: AUTO, LAST
OPTION MENU C)AUDIO SELECT >AUTO LAST
Notes
You cannot automatically revert to the previous parameter settings once you initialize a sound field program group. You cannot separately initialize individual sound field programs. You cannot initialize any sound field program groups when MEMORY GUARD is set to ON.
[[]/[[]:Select [ENTER]:Return
Select AUTO if you want this unit to automatically detect the type of input signals and select the appropriate audio input jack select setting. Select LAST if you want this unit to automatically select the last audio input jack select setting used for the connected input source.
Zone 2 Maximum volume MAX VOL. Use this feature to set the maximum volume level in the Zone 2. Control range: 16.5 dB, 15.0 dB to 30.0 dB Control step: 5.0 dB Notes
The MAX VOL. setting takes priority over the INI VOL. setting. For example, when INI VOL. is set to 20.0 dB and then MAX VOL. is set to 30.0 dB, the volume level is automatically set to 30.0 dB when you turn on the power of this unit next time. The MAX VOL. setting does not affect the output level at the ZONE 2 OUT jacks.
80 En
Zone 2 Initial volume INI VOL. Use this feature to set the volume level of Zone 2 when the power of this unit is turned on. Choices: Off, 80.0 dB to +16.5 dB Control step: 0.5 dB Notes
The MAX VOL. setting takes priority over the INI VOL. setting. When you select FRONT B, PRNS or NONE in EXTRA SP ASSIGN (see page 70), Zone 2 SP Not Assigned appears in the OSD and the ZONE2 SET parameter is not available. The INI VOL. setting does not affect the output level at the ZONE 2 OUT jacks.
[[]/[[]:Select [ENTER]:Return
Charge on standby STANDBY CHARGE Use this feature to select whether this unit charges the battery of the stationed iPod or not when this unit is in the standby mode (see page 56). Choices: AUTO, OFF Select AUTO to charge the battery of the stationed iPod when this unit is turned on and in the standby mode. Select OFF to charge the battery of the stationed iPod only when this unit is turned on.
81 En
Setting the input source of the customized SCENE template on the remote control
If you customize the input source of the selected SCENE template, you must set the input source of the SCENE template on the remote control to operate the input source component correctly.
1 2
Press the desired A SCENE button on the remote control. Press the desired buttons in the * area below to control the input source component of the selected SCENE template.
POWER POWER
Press and hold the A SCENE button and the desired input selector button (A). The transmit indicator (X) flashes twice. Keep holding down the buttons pressed in step 2 until OK appears in the display window (J) on the remote control. Note
If the setting of the input source is not successful, NG appears in the display window (J). In this case, repeat the setting procedure.
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
SCENE buttons
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
SELECT
AMP
+
TV VOL
+
TV CH
+
SOURCE
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
Set to SOURCE
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
A/B/C/D/E
STRAIGHT
RETURN
DISPLAY
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
8
SLEEP
+ 10
ENT
REC
FREQ/TEXT EON
MACRO
OFF
ON
RENAME
Note
*
These buttons control the input source component. See page 84 for details of the function of each button.
82 En
Controlling a TV
Set the operation mode selector to LTV to control your TV. To control your TV, you must set the appropriate remote control code for DTV/CBL or PHONO (see page 85). When you set the remote control codes for both DTV/CBL and PHONO, priority is given to the one set for DTV/CBL.
*2
POWER POWER
STANDBY
POWER
TV
AV
SCENE
*1
3 4
CD DVD
*1
POWER
POWER
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
1
PHONO
2
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DTV/CBL
DVR
VCR
DVD
SELECT
SELECT
AMP
AMP
+
TV VOL
+
TV CH
+
SOURCE
+
TV CH
+
SOURCE
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
*1
AUDIO
PURE DIRECT
*1
TV VOL
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
TITLE
BAND
MENU
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
ENTER
A/B/C/D/E
STRAIGHT
*1
A/B/C/D/E
STRAIGHT
*2
RETURN
DISPLAY
RETURN
DISPLAY
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
1
STEREO
4
NIGHT
*2
ADVANCED OPERATION
8
SLEEP
8
SLEEP
+ 10
ENT
+ 10
ENT
REC
FREQ/TEXT EON
MACRO
REC
MODE- PTY SEEK- START
LEARN CLEAR
FREQ/TEXT
EON
MACRO
OFF
ON
RENAME
OFF
ON
RENAME
Notes
*1
Notes
*1
These buttons always control this unit regardless of the operation mode selector position. *2 These buttons control this unit only when the component operation mode selector is set to L AMP.
These buttons always control your TV regardless of the operation mode selector position. Remote control
TV POWER TV VOL +/ TV CH +/ TV MUTE TV INPUT
Digital TV/Cable TV
Turns on or off the power. Increases or decreases the volume level. Changes the channel number. Mutes the audio output. Changes the input source.
*2
These buttons control your TV only when the operation mode selector is set to LTV. For details, see the TV column on page 84.
English
83 En
POWER
POWER
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
2 3 4 5 6
LEVEL
PRESET/CH
SET MENU
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
A/B/C/D/E
STRAIGHT
7 8 9 0
RETURN
DISPLAY
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
8
SLEEP
9
SELECT
+ 10
ENT
AMP
+
TV VOL
+
TV CH
+
SOURCE
REC
FREQ/TEXT EON
MACRO
VOLUME
OFF
ON
RENAME
TV MUTE
TV INPUT
MUTE
TV
TV
VCR power
*2
LD player
Power *1
CD player
Power *1
Tuner
Power *1 Band
iPod
1 2 3
AV POWER Power *1 TITLE ENTER Title Menu enter Menu up Menu down Menu left Menu right Return Numeric buttons Search backward Search forward Skip backward Skip forward
Title Menu select Menu up Menu down Menu left Menu right Return Numeric buttons DVR search backward *2 DVR search forward *2 DVR skip backward DVR skip forward DVR rec *2 DVR stop
*2
Subsequent menu Preset up (1 to 8) Preset down (1 to 8) Preset down (A to E) Direction A/B Preset up (A to E) Up Down Previous menu Subsequent menu
4 5 6
Return Numeric buttons DVR search backward *2 DVR search forward *2 DVR skip backward DVR skip forward DVR rec *2 DVR stop
*2
Numeric buttons Search backward Search forward Chapter/Skip backward Chapter/Skip forward
Numeric buttons Search backward Search forward Skip backward Skip forward Disc skip
Numeric buttons Search backward Search forward Skip backward Skip forward Rec Stop Pause Play Search backward Search forward Direction back Direction forward Rec Stop Pause Play Stop Pause (Play/Pause) *4 Play (Play/Pause) *4 Previous menu Search backward *3 Search forward *3 Skip backward Skip forward
Disc skip (player) Rec Rec (recorder) Stop Pause Play Menu Audio Display Enter Stop Pause Play
Stop
DVR pause *2 DVR pause *2 Pause DVR play *2 Menu DVR play *2 Menu Audio Display Enter/recall Display Enter Display Play
7 8 0 A
Display
Display
Display
Notes
*1 *2
This button is operational only when the original remote control supplied with the component has a POWER button. These buttons operate your VCR or DVR when you set the appropriate remote control code for DVR (see page 85). *3 Press and hold to search backward or forward. *4 Simple remote mode (see page 56).
84 En
ADVANCED OPERATION
Note
You cannot set a remote control code for the optional area. See page 87 to program buttons operated within this component control area.
DVD
Note
You may not be able to operate your Yamaha component even if a YAMAHA remote control code is preset as listed above. In this case, try setting another YAMAHA remote control code.
Set the operation mode selector to L SOURCE and then press an input selector button (B), or to select the input area you want to set up.
PHONO MULTI CH IN
AMP
V-AUX/DOCK
SOURCE TV
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
English
85 En
Press and hold T LEARN for about 3 seconds using a ballpoint pen or similar object. The library name (ex. L;DVD) and the name of the selected input area (ex. DVD) appear alternately in the display window (J) on the remote control.
Press the numeric buttons (F) to enter the four-digit remote control code for the component you want to use. For a complete list of available remote control codes, refer to List of remote control codes at the end of this manual.
CLASSICAL
LIVE/CLUB ENTERTAIN MOVIE
1
STEREO
LEARN
2
SUR. DECODE
3
SELECT
4
EXTD SUR.
y
You can set a remote control code of a different type of component to an input area. Press D l / h repeatedly to change the library (component category). Library choices: L;DVD, L;DVR, L;LD, L;CD, L;CDR, L;MD, L;TAP (tape), L;TUN (tuner), L;AMP, L;TV, L;CAB (cable), L;SAT (satellite), L;VCR If you want to setup for another input area, press the input selector button, or , or press J SELECT k / n repeatedly to select the input area.
Press D ENTER to set the number. OK appears in the display window (J) on the remote control if setting was successful. NG appears in the display window (J) on the remote control if the setting was unsuccessful. In this case, start over from step 3. y
If you continuously want to set up another code for another component, press the input selector button (B) or , or J SELECT k / n repeatedly to select the component, then repeat steps 2 through 5.
Notes
Be sure to press and hold T LEARN for at least 3 seconds, otherwise the learning process will start. If you do not complete each of the following steps within 30 seconds, the setting mode will be automatically canceled. In this case, start over from step 2.
Press D ENTER. The four-digit code set for the selected component appears in the display window (J). Note
0000 appears in the display window (J) if no code has been set.
Press p or AV POWER to confirm whether you can control your component using the remote control.
POWER
or
AV
y
If operation is not possible and the manufacturer of your component has more than one code, try each of them until you find the correct one.
Notes
ERROR appears in the display window (J) on the remote control if you press a button not indicated in the respective step, or when you press more than one button simultaneously. The supplied remote control does not contain all possible codes for commercially available audio and video components (including Yamaha components). If operation is not possible with any of the remote control codes, program the new remote control function using the learn feature (see Programming codes from other remote controls on page 87) or use the remote control supplied with the component. Functions programmed using the learn feature take priority over remote control code functions.
86 En
Place this remote control about 5 to 10 cm (2 to 4 in) apart from the other remote control on a flat surface so that their infrared transmitters are aimed at each other.
V-AUX/DOCK
DTV/CBL DVR POWER PHONO MULTI CH IN
TV
POWER
TUNER
AV
2
SCENE
MD/CD-R
STANDBY
VCR
POWER
SELECT
DVD
CD
POWER
POWER
STANDBY
POWER
TITLE
BAND
MENU
AUDIO
TV
AV
SCENE
PURE DIRECT
ENTER
5 to 10 cm
1
PHONO
2
MULTI CH IN
4
RETURN
A/B/C/D/E
STRAIGHT
DISPLAY
V-AUX/DOCK
TUNER
MD/CD-R
CD
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
DTV/CBL DVR
4
NIGHT
VCR
DVD
STEREO
8
SLEEP
9
SELECT
+ 10
ENT
AMP
+
TV VOL
+
TV CH
+
SOURCE
REC
FREQ/TEXT EON
MACRO
VOLUME
Press T LEARN using a ballpoint pen or similar object. LEARN and the name of the selected input area (ex. DVD) appear alternately in the display window (J) on the remote control.
TV MUTE
TV INPUT
MUTE
TV
OFF
ON
RENAME
LEARN
Notes
Do not press and hold T LEARN. If you hold it down for more than 3 seconds, the remote enters the remote control code setting mode. If you do not complete each of the following steps within 30 seconds, the learning mode will be automatically canceled. In this case, start over from step 3.
Set the operation mode selector to L SOURCE and then press an input selector button(B), or to select a an input area.
Note
Make sure that the operation mode selector is set to L SOURCE. When you set the operation mode selector to L AMP and program a remote control codes from other remote controls, the programmed key cannot operate the amplifier function of this unit.
Press the button for which you want to program the new function. LEARN appears in the display window (J) on the remote control.
English
87 En
Press and hold the button you want to program on the other remote control until OK appears in the display window (J) on the remote control. NG appears in the display window (J) on the remote control if learning was unsuccessful. In this case, start over from step 4.
V-AUX/DOCK
DTV/CBL DVR
Set the operation mode selector to L AMP or L SOURCE and then press an input selector button (B), or to select the input area you want to rename. The name of the selected input area appears in the display window (J).
AMP SOURCE TV
PHONO MULTI CH IN
POWER
PHONO MULTI CH IN
TV
POWER
TUNER
AV
2
SCENE
MD/CD-R
STANDBY
VCR
POWER
SELECT
DVD
CD
y
If you want to program another function, repeat steps 4 and 5. If you continuously want to program another function for another component, press J SELECT k / n to select the component, and then repeat steps 4 and 5.
V-AUX/DOCK
TUNER
MD/CD-R
CD
or
DTV/CBL DVR VCR DVD
AMP SOURCE TV
2
Notes
ERROR appears in the display window (J) on the remote control if you press a button not indicated in the respective step, or when you press more than one button simultaneously. This remote control can learn approximately 200 functions. However, depending on the signals learned, FULL may appear in the display before you program 200 functions. In this case, clear unnecessary programmed functions to make room for further learning. Learning may not be possible in the following cases: when the batteries in the remote control for this unit or other components are weak. when the distance between the two remote controls is too great or too small. when the remote control infrared windows are not facing each other at the appropriate angle. when the remote control is exposed to direct sunlight. when the function to be programmed is continuous or uncommon.
Note
If you do not complete each of the following steps within 30 seconds, the renaming mode will be automatically canceled. In this case, start over from step 2.
88 En
Press D k / n to select and enter a character. Pressing D n changes the character as follows: A to Z, 1 to 9, 0, + (plus), (hyphen), ; (semicolon), / (slash), and space. Pressing D k changes the characters in reverse order.
PRESET/CH
ENTER
A/B/C/D/E
MACRO operations
Macro buttons
POWER
POWER
STANDBY
POWER
TV
AV
SCENE
REC
1
PHONO
2
MULTI CH IN
FREQ/TEXT
EON
MACRO
OFF
ON
RENAME
V-AUX/DOCK
TUNER
MD/CD-R
CD
ENTER
DTV/CBL
DVR
VCR
DVD
A/B/C/D/E
MACRO ON/OFF
MACRO
y
Press D l to move the cursor to the previous position.
ADVANCED OPERATION
Press D ENTER to set the new name. OK appears in the display window (J) on the remote control if renaming was successful. NG appears in the display window(J) on the remote control if renaming was unsuccessful. In this case, start over from step 3. y
If you continuously want to rename another input area, press the input selector button (B), , or , or press J SELECT k / n repeatedly to select the component, then repeat steps 3 through 5.
2 3
Press the desired macro button. Set the T MACRO ON/OFF selector to OFF when you finish to using the macro programming operation.
OFF
ON
MACRO LEARN CLEAR
Notes Note
ERROR appears in the display window (J) on the remote control if you press a button not indicated in the respective step, or when you press more than one button simultaneously. While the remote control is running a macro program, it does not accept any other operation until it has completed running the program (the transmission indicator stops flashing). Continue to aim the remote control at the component the macro is operating until the macro operation is complete.
y
This feature is useful when you change the input or output assignment for digital jacks and component video input jacks. Refer to Input rename on page 77.
English
89 En
(*2)
POWER
POWER
(*1)
POWER
TV
PHONO
PHONO
MULCH CH IN
MULCH CH IN
V-AUX/DOCK
V-AUX/DOCK
(*3) (MD/CD-R area) (*4) (CD area) (*4) (DVR area) (*4) (VCR area) (*4)
TUNER
POWER
TUNER
MD/CD-R
(*1)
MD/CD-R
CD
CD
DTV/CBL
DTV/CBL
DVR
DVR
VCR
VCR
DVD
DVD
You can turn on some components (including Yamaha components) connected to this unit by connecting them to the AC OUTLETS on the rear panel of this unit. Power control may not be synchronized with this unit depending on the component. For details, refer to the operating instructions for the connected component. *2 When the remote control code for your TV is set up for either DTV/CBL or PHONO (see page 85), you can turn on the power of your TV without selecting an input source. The remote control code set up for DTV/CBL takes priority over the one for PHONO. *3 When TUNER is selected as the input source, this unit plays the last station received before the unit was set in the standby mode. *4 Playback can be started for any Yamaha remote control-compatible CD player, CD recorder, DVD player, or DVD recorder. When using macros to operate other components, you will need to program the play button on the input area of that component (see page 87) or set a remote control code (see page 85).
90 En
Note
AGAIN appears in the display window (J) if you press a button other than a macro button.
Set the operation mode selector to L AMP or L SOURCE and then press T MACRO using a ballpoint pen or similar object. MCR ? appears in the display window (J) on the remote control.
AMP SOURCE
Press the buttons for the functions you want to include in the macro operation in sequence. You can set up to 10 steps (10 functions). After you have set 10 steps, FULL appears and the remote control automatically exits the macro mode. The following example is for programming the following procedure: Step 1 (MCR 1): Press POWER. Step 2 (MCR 2): Press DVD. Step 3 (MCR 3): Press STRAIGHT.
MCR 1: POWER
POWER POWER
STANDBY
POWER
TV
AV
SCENE
1
3 4
LEVEL
PRESET/CH
SET MENU
1
PHONO
2
MULTI CH IN
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
V-AUX/DOCK
TUNER
MD/CD-R
CD
A/B/C/D/E
STRAIGHT
DTV/CBL DVR
VCR
DVD
RETURN
DISPLAY
TV
MCR 3: STRAIGHT
or
AMP SOURCE TV
MACRO
MCR 2: DVD
ADVANCED OPERATION
Note
If you do not complete each of the following steps within 30 seconds, the macro programming mode will be automatically canceled. In this case, start over from step 1.
Flashes alternately so you can set the next step
Press the macro button you want to use to operate the macro. The macro button name (ex. M;DVD) and the selected component name (ex. DVD) appear alternately in the display window (J) on the remote control.
STANDBY
POWER
Note
To change the selected input area, press J SELECT k / n. Pressing the input selector buttons will program a macro step, whereas J SELECT k / n only changes the selected input area.
Press T MACRO again using a ballpoint pen or similar object when the operation sequence you want to program is complete. Note
PHONO
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
ERROR appears in the display window (J) if you press more than one button simultaneously.
English
91 En
Clearing configurations
You can clear all changes made in each function set, such as learned functions, macros, renamed input area names and setup remote control ID.
Press and hold T CLEAR again for about 3 seconds. WAIT appears in the display window (J). If clearing was successful, C;OK appears in the display window (J) on the remote control.
CLEAR
Set the operation mode selector to L AMP or L SOURCE and then press T CLEAR by using a ballpoint pen or similar object. CLEAR appears in the display window (J).
AMP SOURCE TV
y
Once you have cleared a learned function for a button, the button reverts to the factory setting (or to the manufacturer setting, if you have set remote control codes).
or
AMP SOURCE TV
CLEAR
Notes
L;ALL and FCTRY may take about 30 seconds to complete. C;NG appears in the display window (J) if clearing was unsuccessful. In this case start over from step 2. ERROR appears in the display window (J) if you press a button not indicated in the respective step, or if you press more than one button simultaneously.
Note
If you do not complete each of the following steps within 30 seconds, the clearing mode will be automatically canceled. In this case, start over from step 1.
92 En
Set the operation mode selector to L AMP or L SOURCE and then press an input selector button(B), or to select the input area containing the function you want to clear. The selected component name appears in the display window (J).
AMP SOURCE TV
PHONO MULTI CH IN
Press and hold T CLEAR using a ballpoint pen or similar object and then press the button you want to clear for about 3 seconds. C;OK appears in the display window (J) if clearing was successful. Once C;OK appears in the display window (J) on the remote control, release the ballpoint pen or similar object used to press T CLEAR to exit the clearing mode. The remote control returns to the learning mode.
or
AMP SOURCE TV
V-AUX/DOCK
TUNER
MD/CD-R
CD
RENAME
DTV/CBL
DVR
VCR
DVD
y
If you continuously want to clear another function, repeat step 3. If you continuously want to clear another function for another component, press J SELECT k / n to select the input area, then repeat step 3. Once you clear a learned function, the button reverts to the factory setting (or to the manufacturer setting if you have set remote control codes).
Press T CLEAR using a ballpoint pen or similar object. LEARN and the selected component name (ex. DVD) appear alternately in the display window (J).
ADVANCED OPERATION
Notes
C;NG appears in the display window (J) on the remote control if clearing was unsuccessful. In this case, start over from step 2. ERROR appears in the display window (J) on the remote control if you press more than one button simultaneously.
LEARN
Notes
Do not press and hold T LEARN. If you hold it down for more than 3 seconds, the remote control enters the remote control code setting mode. If you do not complete each of the following steps within 30 seconds, the learning mode will be automatically canceled. In this case, start over from step 2.
English
93 En
Set the operation mode selector to L AMP or L SOURCE and then press T MACRO using a ballpoint pen or similar object. MCR ? appears in the display window (J) on the remote control.
AMP SOURCE TV
Press and hold T CLEAR using a ballpoint pen or similar object, then press the macro button you want to clear for about 3 seconds. C;OK appears in the display window (J) on the remote control if clearing was successful.
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
OFF
ON
MACRO
LEARN
CLEAR
RENAME
or
AMP SOURCE TV
MACRO
y
If you continuously want to clear another function, repeat step 2. Once you clear a programmed function, the button reverts to the factory setting (or to the manufacturer setting if you have set remote control codes).
Note
If you do not complete each of the following steps within 30 seconds, the macro programming mode will be automatically canceled. In this case, start over from step 1.
Notes
C;NG appears in the display window (J) on the remote control if clearing was unsuccessful. In this case, start over from step 2. ERROR appears in the display window (J) on the remote control if you press more than one button simultaneously.
94 En
Connecting Zone 2
You need the following additional equipment to use the multi-zone functions of this unit: An infrared signal receiver in the second zone. An infrared signal emitter in the main zone. This emitter transmits the infrared signals from the remote control via the infrared signal receiver in the second zone to a CD player or a DVD player, etc. in the main zone. An amplifier and speakers in the second zone. y
Since there are many possible ways to connect and use this unit in a multi-zone configuration, we recommend that you consult with your nearest authorized Yamaha dealer or service center about the Zone 2 connections that best meet your requirements. Some Yamaha models are able to connect directly to the REMOTE jacks of this unit. If you own these products, you may not need to use an infrared signal emitter. Up to 6 Yamaha components can be connected as shown below.
REMOTE IN
REMOTE OUT IN
REMOTE OUT IN
REMOTE
ADVANCED OPERATION
OUT
This unit
Yamaha component
Yamaha component
Amplifier Main zone Second zone (Zone 2) Infrared signal receiver Remote control DVD player This unit Infrared signal emitter
English
Note
To avoid unexpected noise, DO NOT USE the Zone 2 feature with CDs encoded in DTS.
95 En
y
You can use the FRONT B speakers as the front speaker system of another zone. Set EXTRA SP ASSIGN to FRONT B and then FRONT B to ZONE B (see page 70). When you use the internal amplifiers for the Zone 2 speakers, you can adjust the volume level and set the initial volume level and maximum volume level of the Zone 2 speakers (see page 80).
Controlling Zone 2
You can select and control Zone 2 by using the control buttons on the front panel or on the remote control. The available operations are as follows: Selecting the input source of Zone 2 Tuning into FM or AM when TUNER is selected as the input source of Zone 2 (see page 50) Enjoying music stored on your iPod stationed in a Yamaha iPod universal dock (such as YDS-10 sold separately) connected to the DOCK terminal of this unit when V-AUX is selected as the input source (see page 56) Note
You must complete each step while the ZONE2 indicator is flashing in the front panel display. Otherwise, the Zone 2 mode is automatically canceled and this unit returns to the normal operation mode. In this case, repeat the Zone 2 selection procedure.
Activating the Zone 2 operation mode Press 9 ZONE CONTROL to control Zone 2. The ZONE2 indicator flashes in the front panel display for approximately 10 seconds.
ZONE2
Flashes
96 En
Operate the following operations after activating the Zone 2 operation mode.
Turning on or off Zone 2 using the remote control I POWER and H STANDBY on the remote control work differently depending on the selected zone that appears in the display window (J) on the remote control. When the main zone, Zone 2 mode is selected, you can turn on the main zone or Zone 2 or set them to the standby mode individually. When the all mode is selected, pressing I POWER turns on the main zone and Zone 2 simultaneously and pressing H STANDBY sets them to the standby mode simultaneously.
Control mode Display window (J) Name of the selected input area ZONE 2 or 2;name of the selected input area POWER and STANDBY Turns on the main zone only or sets it to the standby mode. Turns on Zone 2 or sets it to the standby mode.
Operating Zone 2 Rotate the I INPUT selector to select the desired input source while the ZONE2 indicator is flashing in the front panel display. Select TUNER as the input source to use the TUNER features in Zone 2. For details about the TUNER operations, see FM/AM tuning on page 50. Select V-AUX as the input source to use iPod features in Zone 2. For details about the iPod operations, see Using iPod on page 56. y
You must complete this step within 10 seconds while the selected zone flashes in the front panel display. Otherwise, the currently selected zone mode is automatically canceled. In this case, press 9 ZONE CONTROL on the front panel again.
I POWER: turns Set Zone 2 to the standby mode Press 8 ZONE 2 ON/OFF to set Zone 2 to the standby mode.
All mode
ALL on the main zone and Zone 2. H STANDBY: sets the main zone and Zone 2 to the standby mode.
ADVANCED OPERATION
Notes
When the remote control is in the main zone mode, MAIN appears for a few seconds when I POWER or H STANDBY is pressed. ALL appears in the display window (J) on the remote control only when SELECT n is pressed.
Selecting the input source of Zone 2 Press one of the input selector buttons (B) to select the input source of the selected zone. If the remote control is used to select the input source, 2; name of the selected input area is displayed in the display window (J) on the remote control when Zone 2 is selected respectively. Note
The selected input source is shared across all zones.
SELECT
TV
English
97 En
ADVANCED SETUP
Advanced setup
This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. Notes
The settings you make are reflected next time you press B MASTER ON/OFF inward to the ON position to turn on this unit (see page 25). Only B MASTER ON/OFF, C TONE CONTROL and the D PROGRAM selector are effective while you are using the advanced setup menu. No other operations can be made while you are using the advanced setup menu. The advanced setup menu is only available in the front panel display.
4 5
Press C TONE CONTROL repeatedly to change the selected parameter setting. Press B MASTER ON/OFF to release it outward to the OFF position to save the new setting and turn off this unit. y
The settings you made are reflected next time you turn on this unit.
MASTER
ON
OFF
Rotate the D PROGRAM selector to select the parameter you want to adjust. The name of the selected parameter appears in the front panel display. See page 99 for a complete list of available parameters.
SP IMP.-8 MIN
Currently selected parameter Currently selected parameter setting
98 En
Advanced setup
Speaker impedance SP IMP. Use this feature to set the speaker impedance of this unit so that it matches that of your speakers. Choices: 8 MIN, 6 MIN Select 8 MIN to set the speaker impedance to 8 . Select 6 MIN to set the speaker impedance to 6 .
SP IMP. Speaker Impedance level
If you use one set (A or B), the impedance of each speaker must be 8 or higher. Front If you use two sets (A and B), the impedance of each speaker must be 16 or higher.* Center Surround Surround back If you use one set (A or B), the impedance of each speaker must be 4 or higher. Front If you use two sets (A and B), the impedance of each speaker must be 8 or higher. Center Surround Surround back
*
1 2
Set the operation mode selector to L AMP or L SOURCE. Press and hold T LEARN for about 3 seconds using a ballpoint pen or similar object and then press D l / h repeatedly until L;AMP appears in the display window (J) on the remote control.
PRESET/CH
8 MIN
LEARN
ENTER
ADVANCED OPERATION
A/B/C/D/E
6 MIN
Notes
Be sure to press and hold T LEARN for at least 3 seconds, otherwise the learning process will start. If you do not complete each of the following steps within 30 seconds, the setting mode will be automatically canceled. In this case, start over from step 1.
The Canada model cannot use two separate speaker systems (A and B) simultaneously when SP IMP. is set to 8 MIN.
User presets PRESET Use this feature to reset all the parameters of this unit to the initial factory settings (see page 109). Choices: CANCEL, RESET Select CANCEL not to reset any parameters of this unit. Select RESET to reset the parameters of this unit.
Notes
This setting completely resets all the parameters of this unit including the SET MENU parameters. The initial factory settings are activated next time you turn on this unit.
Press D ENTER. The four-digit code set for the selected input area appears in the display window (J) on the remote control.
English
99 En
Y H
POWER
POWER
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
SELECT
J K L M N O P Q R
CLASSICAL
AMP
+
TV VOL
+
CH
+
SOURCE
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
C D E F
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
A/B/C/D/E
STRAIGHT
RETURN
DISPLAY
LIVE/CLUB
ENTERTAIN
MOVIE
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
1
STEREO
4
NIGHT
8
SLEEP
+ 10
ENT
S V W
APPENDIX
REC
FREQ/TEXT EON
MACRO
OFF
ON
RENAME
ii
List of remote control codes Liste des codes de commande Liste der Fernbedienungscodes Lista ver fjrrstyrningskoder Lijst met afstandsbedieningscodes
CABLE
ABC 0030, 0035 AMERICAST 0926 BELL SOUTH 0926 BIRMINGHAM CABLE COMMUNICATIONS 0303 BRITISH TELECOM 0030 CABLE & WIRELESS 1095 DAERYUNG 0035, 0504, 0904, 1904 DIRECTOR 0503 FILMNET 0470 GENERAL INSTRUMENT 0030, 0303, 0503, 0837, GOLDSTAR 0171 HAMLIN 0036, 0300 JERROLD 0030, 0303, 0503, 0837 LG 0171 MNET 0470 MEMOREX 0027 MOTOROLA 0303, 0503, 0837, 1133 NTL 1095 NOOS 0844 ONO 1095 PVP STEREO VISUAL MATRIX 0030 PACE 0264, 1087, 1095 PANASONIC 0027, 0035, 0134 PARAGON 0027 PHILIPS 0332, 0344 PIONEER 0171, 0560, 0904, 1904 PULSAR 0027 QUASAR 0027 REGAL 0300, 0306 RUNCO 0027 SAGEM 0844 SAMSUNG 0027, 0171 SCIENTIFIC ATLANTA 0035, 0504, 0904, 1904 SONY 1033 STARCOM 0030 SUPERCABLE 0303 TS 0030 TELE+1 0470 TELEWEST 1095 TORX 0030 TOSHIBA 0027 TRANS PX 0303 UNITED CABLE 0030 ZENITH 0027, 0552, 0926
CD PLAYER
AIWA 0184 ARCAM 0184 AUDIO RESEARCH 0184 AUDIO TON 0184 AUDIOLAB 0184 AUDIOMECA 0184 CAIRN 0184 CALIFORNIA AUDIO LABS 0056 CARVER 0184, 0206 CYRUS 0184 DKK 0027 DMX ELECTRONICS 0184 DENON 0900 DYNAMIC BASS 0206 EMERSON 0332 FISHER 0206 GENEXXA 0059, 0332 GOODMANS 0332 GRUNDIG 0184 HARMAN/KARDON 0184, 0200 HITACHI 0059 JVC 0099 KENWOOD 0055, 0064 KRELL 0184 LXI 0332 LINN 0184 MCS 0056 MAGNAVOX 0184, 0332 MARANTZ 0056, 0184 MATSUI 0184 MEMOREX 0332 MERIDIAN 0184 MICROMEGA 0184 MIRO 0027 MISSION 0184 MYRYAD 0184 NAD 0027 NSM 0184 NAIM 0184 OPTIMUS 0027, 0059, 0064, 0206, 0332 PANASONIC 0056 PHILIPS 0184 PIONEER 0059, 0332 POLK AUDIO 0184 PROTON 0184 QED 0184 QUAD 0184 QUASAR 0056 RCA 0059, 0206, 0332 REALISTIC 0206 REVOX 0184 ROTEL 0184
SAE 0184 SANSUI 0184, 0332 SANYO 0206 SCOTT 0332 SEARS 0332 SHARP 0064 SIMAUDIO 0184 SONIC FRONTIERS 0184 SONY 0027 SYMPHONIC 0332 TAG MCLAREN 0184 TANDY 0059 TECHNICS 0056 THORENS 0184 THULE 0184 UNIVERSUM 0184 VICTOR 0099 WARDS 0184 YAMAHA 2300, 2301
HITEKER JVC KLH KENWOOD KOSS LG LIMIT MAGNAVOX MARANTZ MEMOREX MICO MICROSOFT MINTEK MITSUBISHI MUSTEK NESA ONKYO ORITRON PALSONIC PANASONIC PHILIPS
CD RECORDER
KENWOOD MARANTZ PHILIPS YAMAHA 0653 0653 0653 2400
DVD PLAYER
ACOUSTIC SOLUTIONS 0757 ALBA 0744 AMSTRAD 0740 APEX DIGITAL 0699, 0744, 0782, 0821, 0823, 0857, 1127 BLAUPINKT 0744 BLUE PARADE 0598 BUSH 0740 CENTREX 0699 CLATRONIC 0815 CYBERHOME 0741 DVD2000 0548 DAEWOO 0811, 0797 DANSAI 0797 DECCA 0797 DENON 0517 DIAMOND 0795 DIGITREX 0699 EMERSON 0618 ENTERPRISE 0618 FISHER 0697 GE 0549, 0744 GO VIDEO 0742 GOLDSTAR 0768 GRADIENTE 0678 GREENHILL 0744 GRUNDIG 0566 HITACHI 0600, 0691
0699 0585, 0650 0744 0517, 0561 0678 0768 0795 0530, 0702 0566 0858 0750 0549 0744 0548 0757 0744 0530 0678 0699 0517, 0659, 1389 0530, 0566, 0673, 0881 PIONEER 0552, 0598, 0658, 0659 POLK AUDIO 0566 PROSCAN 0549 QWESTAR 0678 RCA 0549, 0598, 0744 ROTEL 0650 SM ELECTRONIC 0757 SAMSUNG 0600 SANYO 0697 SHARP 0657 SHERWOOD 0797 SHINSONIC 0560 SLIM ART 0811 SONY 0560, 0891 SYLVANIA 0702 TATUNG 0797 TEAC 0598, 0744 TECHNICS 0517 THETA DIGITAL 0598 THOMSON 0549 TOSHIBA 0530 URBAN CONCEPTS 0530 XBOX 0549 YAMAHA 0517, 0566, 0572, 2100 ZENITH 0530, 0618, 0768 ZEUS 0811
DVD RECORDER
HITACHI PANASONIC PHILIPS PIONEER TOSHIBA YAMAHA 2815 2800 2808 2804 2803 2807
iii
LD PLAYER
CARVER DENON MARANTZ MITSUBISHI NAD NAGSMI OPTIMUS PHILIPS PIONEER SALORA SONY TELEFUNKEN YAMAHA 0091 0086 0091 0086 0086 0086 0086 0091 0086 0091 0228 0086 2200
MD RECORDER
KENWOOD ONKYO SHARP SONY YAMAHA 0708 0895 0888 0517 2500, 2501, 2502
RECEIVER (TUNER)
ADC AIWA 0558 0185, 1116, 1415, 1432, 1668 ALCO 1417 ANAM 1636 APEX DIGITAL 1284 AUDIOLAB 1216 AUDIOTRONIC 1216 AUDIOVOX 1417 BOSE 1256 CAMBRIDGE SOUNDWORKS 1397 CAPETRONIC 0558 CARVER 1116, 1216 CENTREX 1284 DENON 1387 FERGUSON 0558 FINE ARTS 1216 GRUNDIG 1216 HARMAN/KARDON 0137, 1331 INTEGRA 0162, 1325 JBL 0137, 1333 JVC 0101, 0558, 1401, 1522 KLH 1417, 1439 KENWOOD 1054, 1340 MCS 0066 MAGNAVOX 0558, 1116, 1216, 1296, MARANTZ 0066, 1116, 1216, 1316 MICROMEGA 1216 MUSICMAGIC 1116 MYRYAD 1216 NAD 0347 NORCENT 1416 ONKYO 0162, 0869, 1325 OPTIMUS 0558, 1050 PANASONIC 0066, 1315, 1545, 1790
1116, 1216, 1293, 1295, 1296, 1310, 1316 PIONEER 0041, 0558, 1050, 1411 POLK AUDIO 1316 PROSCAN 1281 QUASAR 0066 RCA 0558, 1050, 1281, 1417, 1636, SABA 0558 SANSUI 1116 SCHNEIDER 0558 SONY 0185, 1085, 1185, 1685, 1785 STEREOPHONICS 1050 SUNFIRE 1340 TEAC 1417 TECHNICS 0066, 1335, 1336, 1545 TELEFUNKEN 0558 THOMSON 1281 THORENS 1216 UHER 0558 VENTURER 1417 VICTOR 0101 WARDS 0041, 0185 YAMAHA 0203, 1203, 1358, 2601 (TUNER ID1) 2602 (TUNER ID2) 2603 (iPod) 2606
PHILIPS
SATELLITE TUNER
@SAT 1327 ABSAT 0150 ALBA 0482 ALPHASTAR 0799 AMSTRAD 0874 ASTON 0169, 1156 ASTRO 0200 ATSAT 1327 AVALON 0423 BLAUPUNKT 0200 BRITISH SKY BROADCASTING 0874, 1202 CANAL DIGITAL 0880 CANAL SATELLITE 0880 CANAL+ 0880 CHAPARRAL 0243 CITYCOM 1203 CONNEXIONS 0423 CROSSDIGITAL 1136 CYRUS 0227 D-BOX 0750, 1154 DMT 1102 DNT 0227, 0423 DAERYUNG 0423 DAEWOO 1323 DIGENIUS 0326 DIRECTV 0274, 0419, 0593, 0666, 0751, 0776, 0846, 1103, 1136, 1169, 1776, 1883 DISH NETWORK SYSTEM 0802, 1032
DISHPRO 0802, 1032 DISTRATEL 0111 DREAM MULTIMEDIA 1264 ECHOSTAR 0194, 0423, 0637, 0802, 0880, 0898, 1032, 1113 ENGEL 1044 EXPRESSVU 0802 FTE 0890 FINLUX 0482 FRACARRO 0898 FUBA 0423 GE 0593 GOI 0802 GALAXIS 0890, 1138 GENERAL INSTRUMENT 0896 GOLD BOX 0880 GRUNDIG 0200, 0874 HTS 0802 HIRSCHMANN 0200, 0423 HITACHI 0482, 0846 HUGHES NETWORK SYSTEM 0776, 1169, 1776 HUMAX 0890, 1203 INVIDEO 0898 JVC 0802 KATHREIN 0150, 0200, 0227, 0276, 0685, 1248 KREISELMEYER 0200 LABGEAR 1323 LOGIX 1044 LORENZEN 0326 MAGNAVOX 0749, 0751 MANHATTAN 0482, 1044, 1110 MARANTZ 0227 MEDIASAT 0880 MEMOREX 0751 METRONIC 0111 MITSUBISHI 0776 MOTOROLA 0896 MYRYAD 0227 NEXT LEVEL 0896 NOKIA 0482, 0750, 0778, 1154, 1250, 1750 OCTALTV 1032 ORBITECH 1127 PACE 0482, 0874, 1202, 1350 PANASONIC 0274, 0728, 0874, 1347 PANDA 0482 PAYSAT 0751 PHILIPS 0160, 0227, 0482, 0749, 0751, 0776, 0880, 1103, 1169, 1776 PIONEER 0880 PROMAX 0482 PROSCAN 0419, 0593 RCA 0170, 0419, 0593, 0882 RFT 0227 RADIOSHACK 0896 RADIOLA 0227 RADIX 0423 SKY 0874, 0883, 1202
SM ELECTRONIC 1227 SABRE 0482 SAGEM 0847, 1141, 1280 SAMSUNG 1044, 1136, 1303, 1319 SAT CONTROL 1327 SATSTATION 1110 SCHWAIGER 1138 SEEMANN 0423 SIEMENS 0200 SONY 0666, 0874, 1666 STAR CHOICE 0896 STRONG 1327 TPS 0847, 1280 TANTEC 0482 TECHNISAT 1126, 1127 TELESTAR 1127 THOMSON 0482, 0880, 1073, 1318 TOPFIELD 1233 TOSHIBA 0776, 0817, 1776 ULTIMATETV 0419, 0666 UNIDEN 0749, 0751 UNIVERSUM 0200 VENTANA 0227 WISI 0200, 0423, 0482 XSAT 0150 ZEHNDER 1102 ZENITH 0883, 1883
TAPE DECK
AIWA 0056 CARVER 0056 GRUNDIG 0056 HARMAN/KARDON 0056 MAGNAVOX 0056 MARANTZ 0056 MYRYAD 0056 OPTIMUS 0054 PHILIPS 0056 PIONEER 0054 POLK AUDIO 0056 RCA 0054 REVOX 0056 SANSUI 0056 SONY 0270 THORENS 0056 WARDS 0054 YAMAHA 2700,2701
TV
AGB AOC 0543 0036, 0057, 0087, 0119, 0120, 0135, 0205, 0207, 0478 0131 0036 0036 0119, 0135, 0680 0120, 0190, 0490 0788 0119 0036, 0057, 0235, 0388, 0543, 0729, 0839 0291 0036, 0064, 0398, 0695
APPENDIX
AKURA ALBA
iv
AMERICA ACTION 0207 AMPRO 0778 AMSTRAD 0036, 0064, 0198, 0398, 0439, 0460, 0543 ANAM 0036, 0207, 0277 ANAM NATIONAL 0277, 0677 ANITECH 0036 APEX DIGITAL 0775, 0792, 0794 AUDIOSONIC 0064, 0136 BANG & OLUFSEN 0592 BASIC 0036 BAUR 0064, 0388, 0539 BAYSONIC 0207 BEAUMARK 0205 BEKO 0397, 0513, 0741, 0742 BELL & HOWELL 0181 BEON 0064 BLAUPUNKT 0222 BLUE SKY 0695, 1064 BONDSTEC 0274 BRADFORD 0207 BRANDT 0136, 0362 BROKSONIC 0263, 0490 BUSH 0036, 0064, 0398, 0401, 0695, 1064 CCE 0064 CGE 0274 CTC 0274 CXC 0207 CANDLE 0057 CARNIVALE 0057 CARVER 0081, 0197 CASCADE 0036 CATHAY 0064 CELEBRITY 0027 CELERA 0792 CENTURION 0064 CHANGHONG 0792 CHING TAI 0036, 0119 CHUN YUN 0027, 0036, 0119, 0207 CHUNG HSIN 0080, 0135, 0207 CIMLINE 0036 CINERAL 0119, 0478 CITIZEN 0057, 0087, 0119 CLARION 0207 CLARIVOX 0064 CLATRONIC 0274, 0397 CONDOR 0347, 0397 CONRAC 0835 CONTEC 0036, 0207 CRAIG 0207 CROSLEY 0081 CROWN 0036, 0064, 0207, 0397, 0445 CURTIS MATHES 057, 0074, 0081, 0087, 0120, 0172, 0181, 0193, 0478, 0729, 1174, 1374 DAEWOO 0036, 0057, 0064, 0119, 0135, 0181, 0197, 0205, 0207, 0401, 0478, 0650, 0661, 1688 DANSAI 0064 DAYTON 0036 DE GRAAF 0235, 0575
DECCA 0064, 0543 DENON 0172 DIGATRON 0064 DIXI 0036, 0064 DUMONT 0044 DWIN 0747, 0801 ECE 0064 ELBE 0286 ELECTROBAND 0027 ELIN 0064, 0575 ELITE 0347 ELTA 0036 EMERSON 0181, 0205, 0207, 0263, 0388, 0490, 0650 ENVISION 0057,0840 EPSON 0860 ERRES 0064 ETHER 0036, 0057 ETRON 0036 EUROPHON 0543 FERGUSON 0064, 0100, 0136, 0265, 0314, 0362, 0587 FIDELITY 0388 FINLANDIA 0235, 0373 FINLUX 0064, 0131, 0132, 0373, 0543 FIRSTAR 0036, 0263 FIRSTLINE 0036, 0274, 0695 FISHER 0131, 0181, 0235, 0397 FLINT 0482 FORMENTI 0064, 0347 FORTRESS 0120 FRONTECH 0190, 0274, 0291 FUJITSU 0710, 0836 FUNAI 0207, 0198, 0291 FUTURETECH 0207 GE 0057, 0074, 0078, 0119, 0205, 0207, 0478, 0587, 1174, 1374, 1481 GEC 0064, 0543 GATEWAY 1782, 1783 GELOSO 0036 GENEXXA 0190 GIBRALTER 0044, 0057 GOLDSTAR 0057, 0064, 0136, 0181, 0205, 0404 GOODMANS 0064, 0398, 0401, 0661 GOREMJE 0397 GRADIENTE 0080, 0197 GRAETZ 0190, 0388 GRANADA 0064, 0235, 0366, 0543 GRANDIN 0637 GRUNDIG 0064, 0222, 0514, 0583, 0614 GRUNPY 0207 HCM 0036, 0439 HALLMARK 0205 HANKOOK 0057, 0205, 0207 HANSEATIC 0064, 0347, 0388, 0455, 0583 HANTAREX 0543 HARMAN/KARDON 0081 HARVARD 0207 HAVERMY 0120 HELLO KITTY 0478
HUA TUN HUANYU HYPSON ICE ITS ITT IMPERIAL INDIANA INFINITY INGELEN INNO HIT INNOVA INTEQ INTERFUNK INTERVISION
0036, 0064 0482 0036, 0057, 0119, 0132, 0136, 0172, 0190, 0205, 0252, 0383, 0508, 0575, 0605, 1172, 1283 0036 0401 0064, 0291 0291, 0398 0398 0190, 0388, 0575 0274, 0397, 0445 0064 0081 0190 0543 0064 0044 0064, 0190, 0274, 0388, 0539
0695, 0835, 1064 0172, 0205 0036, 0177, 0181, 0205, 0277, 0490, 1064 0474
0064, 0291, 0404 0081 0027 0080, 0398, 0490, 0680, 0710 JEAN 0036, 0078, 0119, 0183, 0263 JENSEN 0788 KEC 0207 KTV 0057, 0207 KAISUI 0036 KAPSCH 0190 KARCHER 0637 KATHREIN 0583 KENDO 0064 KENWOOD 0057 KNEISSEL 0286, 0462 KOLIN 0080, 0135, 0207 KORPEL 0064 KOYODA 0036 L&S ELECTRONIC 0835 LG 0057, 0064, 0087, 0135, 0205, 0741 LXI 0074, 0081, 0181, 0183, 0205 LEYCO 0064, 0291 LIESENK & TTER 0064 LOEWE 0539 LUXOR 0383, 0388 M ELECTRONIC 0036, 0064, 0131, 0132, 0136, 0190, 0314, 0373, 0401, 0507 MGA 0057, 0177, 0205 MTC 0057, 0087, 0539 MAGNADYNE 0274, 0543 MAGNAFON 0543 MAGNAVOX 0057, 0081, 1281, 1481 MANESTH 0291, 0347 MARANTZ 0057, 0064, 0081, 0583 MARK 0064 MATSUI 0036, 0064, 0235, 0398, 0514, 0543 MATSUSHITA 0277, 0677 MEDIATOR 0064 JBL JCB JVC
0835 0835 0044, 0074, 0078 0514 0439 0057, 0120, 0135, 0177, 0181, 0205, 0207, 0263, 0277, 0539, 0863, 1277 MIVAR 0318,0319, 0543, 0636 MOTOROLA 0120 MULTITECH 0036, 0207 MYRYAD 0583 NAD 0183, 0205, 0388, 0893 NEC 0036, 0057, 0078, 0181, 0183, 0197, 0205, 0482, 0524, 1731 NEI 0064 NTC 0119 NECKERMANN 0064, 0583 NETSAT 0064 NEWAVE 0036, 0119, 0120, 0205 NIKKAI 0064, 0291 NIKKO 0057, 0119, 0205 NOKIA 0388, 0500, 0507, 0575, 0658 NORCENT 0775, 0851 NORDMENDE 0136, 0314, 0587 OCEANIC 0190, 0388 ONWA 0207, 0460 OPTIMUS 0181, 0193, 0277, 0677 OPTONICA 0120 ORION 0064, 0263, 0347, 0490, 0543 OSAKI 0291, 0439 OTTO VERSAND 0064, 0347, 0539, 0583 PALLADIUM 0397, 0445 PANAMA 0291 PANASONIC 0064, 0078, 0081, 0190, 0277, 0677, 1437 PATHE CINEMA 0265, 0347 PAUSA 0036 PENNEY 0057, 0074, 0078, 0087, 0183, 0205, 1374 PERDIO 0347 PHILCO 0057, 0064, 0081, 0172, 0205, 0207, 0274, 0490, 1688 PHILIPS 0027, 0057, 0064, 0078, 0081, 0119, 0135, 0205, 0401, 0583, 0717, 1481 PHONOLA 0064 PILOT 0057
PIONEER
0136, 0190, 0193, 0314, 0706, 0787, 0893 PORTLAND 0119 PRANDONI-PRINCE 0543 PRIMA 0788 PRISM 0078 PROFEX 0036, 0388 PROSCAN 0074 PROTECH 0036, 0064, 0274, 0291, 0445, 0695 PROTON 0036, 0057, 0205 PULSAR 0044 QUASAR 0078, 0277, 0677 QUELLE 0064, 0131, 0388, 0539 R-LINE 0064 RCA 0027, 0057, 0074, 0117, 0119, 0205, 0706, 1074, 1174, 1274, 1374, 1474, 1481, 1574 RFT 0455 RADIOSHACK 0057, 0074, 0181, 0205, 0207 RADIOLA 0064 RADIOMARELLI 0543 REALISTIC 0057, 0181, 0205, 0207 REDIFFUSION 0388 REOC 0741 REVOX 0064 REX 0190, 0286, 0291 ROADSTAR 0036, 0291, 0445 RUNCO 0044, 0057, 0524, 0630 SBR 0064 SEG 0291, 0695 SEI 0543 SKY 0064 SSS 0207 SABA 0136, 0190, 0314, 0362 SACCS 0265 SAGEM 0637 SAISHO 0036, 0291, 0543 SALORA 0190, 0380, 0388, 0575 SAMBERS 0543 SAMPO 0036, 0057, 0119, 0120, 0181, 0198, 0205, 0677, 1782 SAMSUNG 0036, 0057, 0064, 0087, 0117, 0119, 0181, 0205, 0291, 0397, 0583, 0614, 0645, 0729, 0793, 0839, 0841 SANSEI 0478 SANSUI 0490 SANYO 0131, 0181, 0207, 0235, 0366, 0826 SCHAUB LORENZ 0388 SCHNEIDER 0064, 0274, 0398, 0695 SCOTCH 0205 SCOTT 0205, 0207, 0263 SEARS 0074, 0081, 0181, 0183, 0198, 0205 SELECO 0190, 0286
SEMIVOX SEMP SHARP SHEN YING SHENG CHIA SIAREM SIEMENS SINUDYNE SKANTIC SKYGIANT SKYWORTH SOLAVOX SONITRON SONOKO SONOLOR SONTEC SONY SOUNDESIGN
0207 0183 0057, 0120, 0677 0036, 0119 0036, 0120, 0263 0543 0064, 0222 0543 0383 0207 0064 0190 0235 0036, 0064 0190, 0235 0064 0027, 0677, 0861, 1127, 1532, 1678 0205, 0207
SOUNDWAVE SOWA SQUAREVIEW STANDARD STARLITE STERN SUPREME SYLVANIA SYMPHONIC SYNCO SYSLINE T+A TCM TMK TNCI TVS TACICO TAI YI TANDY TASHIKO TATUNG 0198 0036 0207 0190, 0286 0027 0057, 0081, 0198 0198, 0207 0027, 0087, 0119, 0120, 0205, 0478 0064 0474 0835 0205 0044 0490 0036, 0119, 0205 0036 0120, 0190 0119, 0677 0036, 0064, 0078, 0081, 0087, 0181, 0183, 0543 0036, 0064, 0291, 0439, 0445, 0482, 0695, 1064 0274 0347 0078, 0277, 0677 0078 0036, 0078, 0119, 0120, 0205, 0291, 0680 0081, 0087, 0119, 0177, 0207 0136, 0289, 0362, 0652, 0729 TELEMEISTER TELETECH TENSAI TERA THOMSON THORN TOSHIBA 0347 0036 0347 0057 0136, 0314, 0587, 0652, 1474 0064, 0131, 0388, 0539 0087, 0181, 0183, 0535, 0645, 0677, 0859, 1283, 1383, 1683, 1731 0064, 0445 0078, 0087, 0119, 0183, 0205
0543 0036, 0057, 0119 0347 0064, 0131, 0132, 0291, 0373, 0397, 0519 VECTOR RESEARCH 0057 VESTEL 0064 VICTOR 0080, 0277, 0677, 0680 VIDEOSAT 0274 VIDIKRON 0081 VIDTECH 0205 VIEWSONIC 1782 VISION 0347 VOXSON 0190 WALTHAM 0383 WARDS 0057, 0081, 0205, 0893 WATSON 0064, 0347 WAYCON 0183 WHITE WESTINGHOUSE 0064, 0347, 0490, 0650 YAMAHA 0057, 0172, 0677, 0796, 0860, 2900 (projector), 2901 (projector), 2903, 2904 (projector) YAPSHE 0277 YOKO 0064, 0291 ZENITH 0044, 0119, 0205, 0490
VCR
ASA ADMIRAL ADVENTURA AIKO AIWA 0064, 0108 0075 0027 0305 0027, 0064, 0334, 0375, 0379 AKAI 0068, 0342 AKIBA 0099 ALBA 0099, 0305, 0342, 0379 AMERICA ACTION 0305 AMERICAN HIGH 0062 AMSTRAD 0027 ANAM 0064, 0253, 0267, 0305, 0507 ANAM NATIONAL 0253, 1589 ANITECH 0099 ASHA 0267 ASUKA 0064 AUDIOVOX 0064, 0305 BAIRD 0027, 0068, 0131 BASIC LINE 0099, 0305 BEAUMARK 0267 BELL & HOWELL 0131 BLAUPUNKT 0253 BRANDT 0347 BRANDT ELECTRONIC 0068 BROKSONIC 0211, 0375, 1506 BUSH 0099, 0305, 0379 CCE 0099, 0305 CGE 0027 CALIX 0064
TEAC
TEKNIKA TELEFUNKEN
0062 0108 0099 0305 0064, 0305, 1305 0099 0379 0064, 0074, 0099, 0267 CROWN 0099, 0305 CURTIS MATHES 0062, 0068, 0087, 1062 CYBERNEX 0267 CYRUS 0108 DAEWOO 0072, 0131, 0305, 0669, 1305 DANSAI 0099 DE GRAAF 0069 DECCA 0027, 0108 DENON 0069 DUAL 0068 DUMONT 0027, 0108, 0131 DYNATECH 0027 ESC 0267, 0305 ELCATECH 0099 ELECTROHOME 0064 ELECTROPHONIC 0064 EMEREX 0059 EMERSON 0027, 0062, 0064, 0070, 0072, 0211, 0267, 0305, 1305, 1506 FERGUSON 0068, 0347 FIDELITY 0027 FINLANDIA 0108, 0131 FINLUX 0027, 0069, 0108, 0131 FIRSTLINE 0064, 0070, 0072, 0099 FISHER 0074, 0131 FUJI 0060, 0062 FUJITSU 0027, 0072 FUNAI 0027 GE 0062, 0087, 0267, 0834, 1062, 1087 GEC 0108 GARRARD 0027 GENERAL 0072 GO VIDEO 0459 GOLDHAND 0099 GOLDSTAR 0064, 0252, 0507, 1264 GOODMANS 0027, 0064, 0099, 0305 GRADIENTE 0027 GRAETZ 0068, 0131, 0267 GRANADA 0108, 0131 GRANDIN 0027, 0064, 0099 GRUNDIG 0099, 0108, 0253, 0374 HCM 0099 HI-Q 0074 HANSEATIC 0064 HARLEY DAVIDSON 0027 HARMAN/KARDON 0108 HARWOOD 0099 HINARI 0099, 0267, 0379 HITACHI 0027, 0064, 0068, 0069, 0267
APPENDIX
vi
HUGHES NETWORK SYSTEMS 0069 HYPSON 0099 ITT 0068, 0131, 0267 ITV 0064, 0305 IMPERIAL 0027 INTERFUNK 0108 JVC 0068, 0072, 0094 JENSEN 0068 KEC 0064, 0305 KLH 0099 KAISUI 0099 KENWOOD 0068, 0094 KODAK 0062, 0064 KOLIN 0068, 0070 KORPEL 0099 LG 0064, 0069, 0072, 0507 LXI 0064 LENCO 0305 LEYCO 0099 LLOYDS 0027 LOEWE 0064, 0108, 1589 LOGIK 0099, 0267 LUXOR 0070, 0075, 0131 M ELECTRONIC 0027 MEI 0062 MGA 0070, 0267 MGN TECHNOLOGY 0267 MTC 0027, 0267 MAGNASONIC 1305 MAGNAVOX 0027, 0062, 0066, 0108, 1808 MAGNIN 0267 MANESTH 0072, 0099 MARANTZ 0062, 0108 MARTA 0064 MATSUI 0375, 0379 MATSUSHITA 0062 MEDION 0375 MEMOREX 0027, 0062, 0064, 0066, 0074, 0075, 0131, 0267, 0334, 0375, 1264 MEMPHIS 0099 METZ 0064, 0374, 1589
MINOLTA MITSUBISHI
0069 0068, 0070, 0094, 0108, 0834 MOTOROLA 0062, 0075 MULTITECH 0027, 0099 MURPHY 0027 MYRYAD 0108 NAD 0131 NEC 0062, 0064, 0068, 0075, 0094, 0131 NATIONAL 0253 NECKERMANN 0108 NESCO 0099 NEWAVE 0064 NIKKO 0064 NOBLEX 0267 NOKIA 0068, 0131, 0267 NORDMENDE 0068, 0347 OCEANIC 0027, 0068 OKANO 0342, 0375 OLYMPUS 0062, 0253 OPTIMUS 0064, 0075, 0131, 0459 ORION 0211, 0375, 0379, 1506 OSAKI 0027, 0064, 0099 OTTO VERSAND 0108 PALLADIUM 0064, 0068, 0099 PANASONIC 0062, 0252, 0253, 0643, 1062, 1589 PATHE MARCONI 0068 PENNEY 0062, 0064, 0069, 0267, 1062, 1264 PENTAX 0069 PERDIO 0027 PHILCO 0062 PHILIPS 0062, 0108, 0645, 1108, 1208 PHONOLA 0108 PILOT 0064 PIONEER 0069, 0094, 0108 POLK AUDIO 0108 PROFITRONIC 0267 PROLINE 0027 PROSCAN 0087, 1087 PROTEC 0099 PULSAR 0066 PYE 0108 QUASAR 0062, 1062 QUELLE 0108
RCA
0062, 0069, 0087, 0267, 0834, 1062, 1087 RADIOSHACK 0027 RADIOLA 0108 RADIX 0064 RANDEX 0064 REALISTIC 0027, 0062, 0064, 0074, 0075, 0131 REOC 0375 REPLAYTV 0641, 0643 REX 0068 ROADSTAR 0064, 0099, 0267, 0305 RUNCO 0066 SBR 0108 SEG 0267 SEI 0108 STS 0069 SABA 0068, 0347 SALORA 0070 SAMPO 0064, 0075 SAMSUNG 0072, 0267, 0459 SANKY 0066, 0075 SANSUI 0027, 0068, 0094, 1506 SANYO 0074, 0131, 0267 SAVILLE 0379 SCHAUB LORENZ 0027, 0068, 0131 SCHNEIDER 0027, 0099, 0108 SCOTT 0070, 0072, 0211 SEARS 0027, 0062, 0064, 0069, 0074, 0131, 1264 SELECO 0068 SEMP 0072 SHARP 0075, 0834 SHINTOM 0099, 0131 SIEMENS 0064, 0108, 0131 SILVA 0064 SINGER 0072, 0099 SINUDYNE 0108 SONIC BLUE 0641, 0643 SONTEC 0064 SONY 0027, 0059, 0060, 0062, 0663, 1259 SUNKAI 0375 SUNSTAR 0027 SUNTRONIC 0027
SYLVANIA
0027, 0062, 0108, 0070, 1808 SYMPHONIC 0027 TMK 0267 TANDY 0027, 0131 TASHIKO 0027, 0064 TATUNG 0027, 0068, 0072, 0094, 0108 TEAC 0027, 0068, 0305, 0334, 0669 TECHNICS 0062, 0253 TECO 0062, 0064, 0068, 0075 TEKNIKA 0027, 0062, 0064 TELEAVIA 0068 TELEFUNKEN 0068, 0347 TENOSAL 0099 TENSAI 0027 THOMAS 0027 THOMSON 0068, 0087, 0094, 0347 THORN 0068, 0131 TIVO 0645, 0663 TOSHIBA 0068, 0070, 0072, 0094, 0108, 0872 TOTEVISION 0064, 0267 UHER 0267 UNITECH 0267 UNIVERSUM 0027, 0064, 0108, 0267 VECTOR 0072 VICTOR 0068, 0094 VIDEO CONCEPTS 0072 VIDEOMAGIC 0064 VIDEOSONIC 0267 VILLAIN 0027 WARDS 0027, 0062, 0069, 0074, 0075, 0087, 0099, 0108, 0267 WHITE WESTINGHOUSE 0099 XR-1000 0027, 0062, 0099 YAMAHA 0068 YAMISHI 0099 YOKAN 0099 YOKO 0267 ZENITH 0027, 0060, 0066, 1506
2007
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VSTRA FRLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia
WJ70020
RX-V861/RX-V661
The circled numbers and alphabets correspond to those in the Owners Manual. Les nombres et lettres dans un cercle correspondent ceux du mode demploi. Die umkreisten Zahlen und Buchstaben entsprechen denen in der Bedienungsanleitung. Inringade nummer och bokstver motsvarar de som anges i bruksanvisningen. De omcirkelde cijfers en letters corresponderen met die in de Gebruiksaanwijzing. .
VOLUME
SPEAKERS
EDIT PRESET/TUNING
FM/AM
A/B/C/D/E
PRESET/TUNING
MEMORY
TUNING AUTO/MAN'L
ZONE 2 ON/OFF
ZONE CONTROL
SCENE
ON
OFF
SILENT CINEMA
EFFECT
S VIDEO
VIDEO
AUDIO
OPTICAL
F G
Y H
POWER
POWER
STANDBY
POWER
TV
AV
SCENE
1
PHONO
2
MULTI CH IN
V-AUX/DOCK
TUNER
MD/CD-R
CD
DTV/CBL
DVR
VCR
DVD
SELECT
J K L M N O P Q R
CLASSICAL
AMP
+
TV VOL
+
CH
+
SOURCE
VOLUME
TV MUTE
LEVEL
TV INPUT
PRESET/CH
MUTE
SET MENU
TV
C D E F
TITLE
BAND
MENU
AUDIO
PURE DIRECT
ENTER
A/B/C/D/E
STRAIGHT
RETURN
DISPLAY
LIVE/CLUB
ENTERTAIN
MOVIE
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
1
STEREO
4
NIGHT
1
STEREO
4
NIGHT
8
SLEEP
+ 10
ENT
S V W
REC
FREQ/TEXT EON
MACRO
OFF
ON
RENAME
Printed in Malaysia
WK14520