DC786 Technical

Product Information
DOW CORNING 786 Mildew Resistant Silicone Sealant

FEATURES
Conforms to
One-part silicone sealant APPLICATIONS DOW CORNING 786 is a one part, flexible; fast curing silicone rubber sealant specifically designed for the sealing of refrigeration units and areas where contact with food is likely. TYPICAL PROPERTIES The following values are not intended for use in preparing specifications: Cure Type Working Time Slump Tack Free Time Cure Time for 2.5mm depth Joint Movement Capability Recovery Staining Hardness (Shore A) Service Temperature Range Application Temperature Range JOINT DESIGN When designing joints using DOW CORNING 786, the minimum joint width should be 6mm. For joints between 6mm-12mm wide, a seal depth of 6mm is required. For joints above 12mm wide, a width to depth ratio of 2:1 should be used. In situations where fillet joints are needed, a minimum of 6mm sealant bite to each substrate is recommended. : : : : : : : : : : Acetoxy 5-10 minutes Nil 1 hour 24 hours +/-25% 100% None 25 -50C to +150C
BS 5889, Type B.
Meets the U.S. Food and Drugs
Administration Regulation No. 21CFR177.2600.

Safe for repeated food contact. Highly resistant to mildew and
mould growth.
Joint movement capability +/-
25%.
Excellent adhesion to most non-
porous surfaces.
Fast cure.
: 5C to 40C
HOW TO USE Surface Preparation Ensure that surfaces to be sealed are clean, dry, sound and grease free. Clean with DOW CORNING R40 Universal Cleaner or methylated spirits depending on the substrates to be sealed, and dry thoroughly with a clean, lint-free cloth before application of sealant. Note: When using any solvent, always provide adequate ventilation. Avoid heat, sparks and open flames. Use solvent resistant gloves. Observe and follow all precautions listed on solvent container label. It is recommended that DOW CORNING 786 is not applied to surfaces that are below 5C as it is impossible to guarantee a dry surface at this temperature. Masking Areas adjacent to the joints should be masked with tape to prevent contamination of the substrates and to ensure a neat sealant line. Masking tape should be removed immediately after tooling. Priming Primer is not required on most common nonporous substrates including vitreous enamel, ceramics, porcelain, glazed tiles, etc. For some metals and plastics priming is required. For specific advice, please refer to the Dow Corning Primer Guide or contact Geocel for technical assistance. Back-Up Materials Where back-up material is required closed cell polyethylene backer rod is recommended. Low tack polyethylene tape should be used in joints too shallow to allow the use of backer rod. Finishing The joint should be tooled within 5 minutes of application to ensure good contact between the sealant and the substrate. Tooling of the sealant also gives a smooth, professional finish.
Clean-Up Excess sealant may be cleaned off tools and non-porous surfaces whilst in an uncured state using DOW CORNING R40 Universal Cleaner. Cured sealant may be removed with the aid of DOW CORNING Silicone Sealant Remover, abrasion or other mechanical means. Care should be taken not to damage plastic surfaces. USEABLE LIFE AND STORAGE 24 months from date of production when stored in cool, dry conditions below 23C. COLOUR RANGE & PACKAGING DOW CORNING 786 Silicone Sealant is available in white and clear and is supplied in 310ml cartridges, packed in boxes of 12. HANDLING PRECAUTIONS Product safety information required for safe use is not included. Before handling, read product and safety data sheets and container labels for safe use, physical and health hazard information. You can obtain a copy from your local Dow Corning sales representative or distributor. LIMITATIONS DOW CORNING 786 Silicone Sealant should not be applied to porous surfaces such as stone or concrete, or to easily corroded metals such as lead or copper. DOW CORNING 786 should not be used against surfaces that bleed oils, plasticisers or solvents. Contact Geocels Technical Services Department for further advice on specific applications.
LIMITED WARRANTY INFORMATION PLEASE READ CAREFULLY The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customers tests to ensure that Dow Cornings products are safe, effective and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent. Dow Cornings sole warranty is that the product will meet the Dow Corning sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. DOW CORNING SPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Geocel Ltd Western Wood Way Langage Science Park Plympton, Plymouth Devon PL7 5BG Tel: 01752 334350 Fax: 01752 202065 Email: [email protected] www.geocel.co.uk

DC786 Technical

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DC786 Technical

Uploaded by

Copyright:

Available Formats

Product Information

DOW CORNING 786 Mildew Resistant Silicone Sealant

Administration Regulation No. 21CFR177.2600.

You might also like