Professional Documents
Culture Documents
Module 10 EASA
Module 10 EASA
1.You are a JAR OPS organization. Explain how you would set-up an aircraft maintenance organization.
2. Describe in detail the process of obtaining a Part-66 Basic License and then describe how a Part-145 quality department can issue a type approval
3. Describe the process for attaining a Part-66 license and how you can obtain an extension to the basic license.
4. What are the relationships between the ANO, BCARs, JARs and AWNs. List the AWNs that are applicable to the Licensed aircraft engineer.
5. An aircraft has suffered structural damage due an accident/incident. Describe the inspection and management procedures and relevant paperwork for rectification.
6. You are a Part-145 company - what audits would the quality department need to carry out to retain the company approval? An organogram would help your answer.
7. Explain in some detail what areas of a 145 approved company need to be audited by the company's quality department. An organogram of the 145 structure may be helpful
9. What are the maintenance requirements of a company under JAR OPS 1:890?
11. What are the relationships between the ANO, BCARs, JARs and AWNs. List the AWNs that are applicable to the Licensed Aircraft Engineer.
12. What are the considerations when moving a private category aircraft into the Commercial Air Transport category?
13. What organization system is required under JAR OPS Subpart M to support the continued airworthiness of its aircraft?
14. As an aircraft operator, how do you maintain your aircraft and what checks do you do?
15. Describe the process for attaining a JAR 66 license and detail the engineers responsibilities under JAR 145.
16. What are the considerations and certifications for release to service when a licensed engineer carries out a component replacement?
Module 9
1. Describe in detail the effects of stress on an engineer and how environmental factors affect stress. Discuss how these affects can be minimized.
2. If a major skin repair was being carried out on an aircraft and you were the team leader, and the repair was not going to be completed within your shift period, how would you do a shift handover for the next shift?
4. There are many different types of maintenance error reporting schemes. Maintenance Error Decision Aid (MEDA) is one. Explain its implementation and how this is achieved within a company?
5. Name two pressures the engineer is subjected to, how they originate and how to prevent them
6. With regard to circadian rhythms, expand on the following: What does 'circadian' mean? What is a 'circadian rhythm'? How is the body affected after a long flight over several time zones? Ref. above - how can the effects be minimized? What is meant by 'post lunch low'? With respect to circadian rhythms, what is meant by 'acrophase'?
7. You are a shift leader carrying out a major airframe repair that will not be completed during your shift. How are you going to communicate this to the incoming shift with regards to outstanding work, data and spares?
8. What are the different types of stress encountered at the workplace, and as an employer, what are the ways to relieve stress of your employees?
7. What is the impact of human factors on: a) Maintenance scheduling, and b) Environmental factors
9. Describe Maintenance Error Decision Aid (MEDA) and how is it utilized for accident prevention.
Module 7
2. Discuss the methods of protection against HIRF and the checks / inspections which would be carried out after a fault was entered in the tech log.
3. You are required to carry out a torque loading. Describe the procedure including all checks and tests to be carried out.
4. You are required to carry out a bonding test on an aircraft. Describe the procedure including all checks and tests to be carried out.
5. Describe the procedure to refuel a medium sized passenger jet Include all safety checks that should be observed.
6. You are tasked with securing a small 50-seater aircraft due to high winds. How and where would you picket the aircraft and what checks would you carry out?
7. Describe the procedure for placing a medium sized aircraft into storage for 6 months. Include any maintenance checks that would be required.
9. Discuss the precautions you would take, before during and after a windscreen replacement.
10. A fiber-reinforced flap has been found damaged (soft spot). What inspections and repairs would you carryout?
12. What is 'Stressed Skin' construction? What inspections would you carryout to it during servicing?
13. After a heavy landing, describe what checks you would carry out including what questions you would ask the flight crew.
14. Describe the procedure for weighing an aircraft. Include all precautions to be taken before during and after the weighing.
15. Describe the procedure for carrying out a dye-penetrant NDT check on an aircraft component.
16. On carrying out a system check of a stall warning system it is discovered that the first officer's stick shaker is inoperative. Describe how you would fault find the system and how you would rectify the defect.
17. On trouble shooting an IDG overheat lamp fault, it was discovered that the connector of the IDG had evidence of overheating. Describe in detail the fault rectification process and how all the work should be recorded.
18. Describe the procedure for towing an aircraft from the hangar to the line, including all safety aspects.
19. Describe the procedure you would follow to remove corrosion from a component.
20. Describe what you would do if the aircraft had suffered a lightning strike. 21. Describe the different methods of de-icing an aircraft. Include details of types of fluid used.
22. During an engine start it is noticed that the No.2 ignition system is not working. What are you going to do to fix the problem and what certification (if any) is required?
24. Describe the procedure used for trouble shooting a DRIVE light of an IDG?
25. On a walk round inspection you notice smoke/vapour in the starboard wheel well. Describe the actions you would take and list possible causes.
26. The pilot reports a burning smell from the flight deck air conditioning system. State your actions and detail possible causes.
27. Describe how you would replace a PCB and the precautions you would take.
28. Discuss the methods of protection against HIRF and the checks/inspections that would be carried out after a fault was entered in the tech log.
29. On carrying out a system check of a stall warning system it is discovered that the first officers stick shaker is inoperative. Describe how you would fault find the system and how you would rectify the defect.
30. On trouble shooting an IDG overheat lamp fault, it was discovered that the connector of the IDG had evidence of overheating. Describe in detail the fault rectification process and how all the work should be recorded.
31. During an engine start it is noticed that the No.2 ignition system is not working. What are you going to do to fix the problem and what certification (if any) is required?
32. After heavy maintenance an aircraft is taken outside for engine runs. the engine will rotate but not ignite, describe the possible causes of this and how you would go about fault finding this problem
33. On a walk round inspection you notice smoke/vapour in the starboard wheel well. Describe the actions you would take and list possible causes
34. The pilot reports a burning smell from the flight deck air conditioning system. State your actions and detail possible causes.
35. Describe how you would replace a PCB, and the precautions you would take.
36. Describe in detail your actions after finding a landing gear strut low.
37. On a major hangar inspection you find corrosion in an unpressurised panel. Detail your actions to return the aircraft to service.
38. Describe the procedures when inspecting a brake unit. What would you do on discovering a brake unit 'worn to limits'?
39. Describe the procedure, documentation used, and those to be filled out when jacking a nose wheel aircraft over 5700kg.
40. List NDT techniques commonly used for inspecting aircraft structure and components. Give details of defects it will find, what materials the techniques may be used on and what are the chief advantages and disadvantages of each technique
41. There is 2 inches of wet snow on the aircraft, the temperature is 2oC, what are your considerations before releasing the aircraft for departure?
44. Describe the procedure of a hold-over item Posted by faaiz at 10:31 AM 0 comments: