Professional Documents
Culture Documents
1305 Variador Allen Bradley
1305 Variador Allen Bradley
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT
Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
Document Update
Notes:
Summary of Changes
The information below summarizes the changes to the 1305 User Manual, publication 1305-5.2 since the last release.
Description of New or Updated Information Added the document update concerning Electronic Motor Overload Protection. Page Beginning of manual
Notes:
Table of Contents
Chapter 1 Information and Precautions
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiving, Unpacking, Inspection, Storing . . . . . . . . . . . . . . . . General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conventions Used In This Manual . . . . . . . . . . . . . . . . . . . . . . Nameplate Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Firmware Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Catalog Number Code Explanation . . . . . . . . . . . . . . . . . . . . . . 1-1 1-1 1-2 1-2 1-3 1-4 1-4 1-5
Chapter 2 Installation/Wiring
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Terminal Block Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Input Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Input Power Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Input Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Electrical Interference EMI/RFI . . . . . . . . . . . . . . . . . . . . . . . 2-7 RFI Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 CE Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Drive Operation without a Human Interface Module (HIM) . . . . . 2-17 Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Output Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Cable Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Chapter 4 StartUp
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Start-up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Chapter 5 Programming
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Chapter Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Function Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Parameter Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Programming Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
ii
Table of Contents
Frequency Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Feature Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Owners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adapter I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Process Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linear List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-25 5-32 5-37 5-39 5-42 5-47 5-50 5-54 5-55 5-56
Appendix A Block Diagram And Specifications Appendix B Serial Communications Appendix C Drive Accessories Appendix D CE Conformity
Chapter
Chapter 4 describes the steps to start up the drive. It includes a typical start up routine defining the adjustments and checks to assure proper operation. Chapter 5 outlines the parameter information of the drive such as description, number, type, units, factory default, minimum and maximum settings. Chapter 6 defines the various drive faults and the appropriate action to take as well as general troubleshooting information. Appendix A contains a block diagram and general specifications of the drive. Appendix B provides the necessary information for drive set up using a PLCR, SLC or other logic controller. A table is provided that lists each parameter by parameter group with space for the user to record any custom parameter settings. Appendix C lists the accessories and their catalog number. Appendix D lists requirements for CE conformity. Index A comprehensive index is provided to assist the user in locating specific information. All parameters and fault information are listed alphabetically under parameters and faults respectively.
PLC is a registered trademark of Allen-Bradley Company. SLC is a trademark of Allen-Bradley Company.
MANUAL OBJECTIVES
The purpose of this manual is to provide the user with the necessary information to install, program, start up and maintain the Bulletin 1305 drive. To assure successful installation and operation, the material presented must be thoroughly read and understood before proceeding. Particular attention must be directed to the ATTENTION and Important statements contained within. Chapter 2 provides instructions on how to mount and wire the drive. It also describes how to operate the drive without a Human Interface Module. Read the Motor Cable Length section on pages 2-13 2-16, and the contact closure inputs information in the Control Terminal Block descriptions on pages 2-19 2-21. Chapter 3 defines the display and control panel keys on the optional Human Interface Module. A flowchart is provided to guide the user through the key strokes of the various menu levels.
1-2
Receiving It is the responsibility of the user to thoroughly inspect the equipment before accepting the shipment from the freight company. Check the item(s) received against the purchase order. If any items are obviously damaged, it is the responsibility of the user not to accept delivery until the freight agent has noted the damage on the freight bill. Should any concealed damage be found during unpacking, it is again the responsibility of the user to notify the freight agent. The shipping container must be left intact and the freight agent should be requested to make a visual inspection of the equipment. Unpacking Remove all packing material from within and around the drive. Important: Before the installation and start-up of the drive, a general inspection of the mechanical integrity (i.e. loose parts, wires, connections, etc.) should be made. Inspection After unpacking, check the item(s) nameplate catalog number against the purchase order. An explanation of the catalog numbering system for the Bulletin 1305 drive is included as an aid for nameplate interpretation. Refer to the following pages for complete nomenclature.
Storing The drive should remain in its shipping container prior to installation. If the equipment is not to be used for a period of time, it must be stored according to the following instructions in order to maintain warrranty coverage: D Store in a clean, dry location. D Store within an ambient temperature range of 40_ to +70_C. D Store within a relative humidity range of 0% to 95%, noncondensing. D Do not store equipment where it could be exposed to a corrosive atmosphere. D Do not store equipment in a construction area.
GENERAL PRECAUTIONS
In addition to the precautions listed throughout this manual, the following statements which are general to the system must be read and understood. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive.
1-3
ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts and assemblies. Static control precautions are required when installing, testing, or servicing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with static control procedures, reference A-B publication 8000-4.5.2, Guarding Against Electrostatic Damage or any other applicable ESD protection handbook. ATTENTION: An incorrectly applied or installed drive can result in component damage or a reduction in product life. Wiring or application errors, such as, undersizing the motor, incorrect or inadequate AC supply, or excessive ambient temperatures may result in malfunction of the system.
ATTENTION: Only personnel familiar with the the drive and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage.
To help differentiate parameter names, display text, and control keys from other text in this manual, the following conventions will be used:
Parameter Names Display Text Control Key Names will appear in [brackets] will appear in quotes. will appear as depicted on the control key, if the key is labeled with letters or numbers (i.e., JOG, SEL) or if the key depicts an icon, its operative term appear with initial capitalization (i.e., Stop, Increment, Enter).
1-4
NAMEPLATE LOCATION
Figure 1.1 Bulletin 1305 Nameplate Location
1305-BA03A-HAP
SER
ES C SE L
AB0516C
FIRMWARE COMPATIBILITY
Drive: HIM: Series C, FRN 6.01 and up Series A, FRN 1.0 through 3.0 Series B, FRN 1.0
Specific Firmware versions are identified by digits to the right/left of decimal. Example 1.01, 2.01.
Firmware version can be found on the drive carton label, on integrated circuits found on the Control Board (see Figure 2.3), or can be viewed in Drive Diagnostics (see Chapter 5).
1-5
1305
First Position
A
Second Position
A02
Third Position
A
Fourth Position
DE
Fifth Position
HA1
Sixth Position
BulletinNumber
Nominal Current Rating A01 A02 A03 A04 A06 A08 A09 A12
Options
Language Code (English language is included in base catalog number. To order a second language, add the appropriate suffix to the drive catalog number.) DE German ES Spanish IT Italian FR French Human Interface Modules, NEMA Type 1 (IP 30) To order installed in the drive, add the appropriate suffix to the drive catalog number. HAP Programmer Only HA1 HIM with Analog Speed Pot HA2 HIM with Digital Up-Down Keys
1-6
In general:
Motor Full Load Amps (FLA) should not exceed the drive output current rating. If the [PWM Frequency] is set above 4kHz, the output current must be derated per the chart on page 5-20.
When operating the drive in an ambient temperature at or near the maximum operating temperature (50C), the following derating guidelines are recommended to guard against overheating depending on application and operating conditions.
Output current value listed for 200V input voltage. At 230V input voltage, output current is 9.6A for 3 phase and 6.8A for single phase. Output current value listed for 380V input voltage. At 415V input voltage, output current is 5.3A. At 460V input voltage, output current is 4.8A. Output current value listed for 380V input voltage. At 415V input voltage, output current is 8.4A. At 460V input voltage, output current is 7.6A.
For derating guidelines at ambient temperatures between 40C and 50C, consult Allen-Bradley.
Installation/Wiring
CHAPTER OBJECTIVES
Chapter 2 provides the information needed to properly mount and wire the drive. Since most start-up difficulties are the result of incorrect wiring, every precaution must be taken to assure that the wiring is done as instructed. All items must be read and understood before the actual installation begins.
Figure 2.1 Mounting Requirements
Chapter
ATTENTION: The following information is merely a guide for proper installation. The National Electrical Code and any other governing regional or local code will overrule this information. The Allen-Bradley Company cannot assume responsibility for the compliance or the noncompliance to any code, national, local or otherwise for the proper installation of this drive or associated equipment. A hazard of personal injury and/or equipment damage exists if codes are ignored during installation.
JOG
JOG
2-2
Installation/Wiring
G 200/230 V Cat. No. 1305- . . . AA02A AA03A AA04A AA08A BA01A BA02A BA03A BA04A BA06A BA09A 380/460 V Cat. No. 1305- . . . C Depth w/o Pot. 122 (4-13/16) 140 (5-1/2) 179 (7-1/16)
F C Depth w/ Pot. 127.1 (5) 145.1 (5-23/32) 184.1 (7-1/4) Approx. Shipping Weight 1.6 (3.5) 1.9 (4.2) 3.6 (8.0)
AA12A
210 (8-1/4)
195 (7-11/16)
179 (7-1/16)
184.1 (7-1/4)
200 (7-7/8)
180 (7-1/16)
66 (2-19/32)
113 (4-7/16)
5 (7/32)
7.5 (5/16)
4.2 (9.2)
Installation/Wiring
2-3
10
Serial Number
JO G
HIM See back for Series Letter and Firmware Revision Level Hinged Cover Retaining Lever
ATTENTION: Proceed with caution. A DC Bus Voltage may be present at the Power Terminal Block (TB1) even when power is removed from the drive.
2-4
Installation/Wiring
Input Devices
Page 2-5
Electrical Interference Input Power Conditioning Page 2-6 Grounding Power Wiring Input Filters Page 2-8
GRD (T1) (T2) (T3) GRD U V W
Input Fusing
Page 2-6
Motor
Installation/Wiring
2-5
INPUT DEVICES
Starting and Stopping the Motor ATTENTION: The drive start/stop control circuitry
includes solid-state components. If hazards due to accidental contact with moving machinery or unintentional flow of liquid, gas or solids exist, an additional hardwired stop circuit is required to remove AC line power to the drive. When AC input power is removed, there will be a loss of inherent regenerative braking effect and the motor will coast to a stop. An auxiliary braking method may be required.
Normal Operation: After the input contactor is closed, the enable, start, and stop signals may be applied. These control signals must be removed before opening the input contactor. The input contactor must not be opened and closed more than once a minute. Bypass Contactors
ATTENTION: An incorrectly applied or installed system can result in component damage or reduction in product life. The most common causes are: D Wiring AC line to drive output or control terminals. D Improper voltage placed on control terminals. D Improper bypass or output circuits not approved by
Allen-Bradley.
by control input signals that will start and stop the motor. A device that routinely disconnects then reapplies line power to the drive (input contactor, etc.) for the purpose of starting and stopping the motor should not be used. If it is necessary to use this method for starting and stopping or if frequent cycling of power is unavoidable, make sure that it does not occur more than once a minute.
D Incorrect or inadequate AC supply. D Excessive ambient temperature. Contact Allen-Bradley for assistance with application or wiring.
system can result in component damage or reduction in product life. Follow these recommendations for application of an input contactor to a 1305 drive.
2-6
Installation/Wiring
INPUT FUSING
ATTENTION: The drive does not provide branch circuit protection. Specifications for the recommended fuse size and type which provide branch circuit protection against short circuits are provided in Table 2.A. Branch circuit breakers or disconnect switches cannot provide this level of protection for drive components.
Table 2.A Maximum Recommended AC Input Line Fuse UL Class J, T, CC, or BS88 (or equivalent)
Three-Phase Rating kW (HP) 0.37 (0.25) 0.55 (0.75) 0.75 (1) 1.5 (2) 2.2 (3) Single-Phase Rating kW (HP) 0.19 (0.25) 0.37 (0.5) 0.55 (0.75) 0.75 (1) 1.5 (2) Fuse 200-230V Rating 6A 6A 10A 15A 25A Fuse 380-460V Rating 3A 3A 6A 10A 15A
4.0 (5) 20A Must be dual element time delay, Bussmann LPJ or equivalent. If fuse blowing is a problem, use dual element type fuses.
Installation/Wiring
2-7
The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supply lines. If the installation combines a drive with sensitive devices or circuits, it is recommended that the lowest possible drive PWM frequency be programmed.
2-8
Installation/Wiring
RFI FILTERING
1305 drives can be installed with an RFI filter, which controls radiofrequency conducted emissions into the main supply lines and ground wiring. If the cabling and installation recommendation precautions described in this manual are adhered to, it is unlikely that interference problems will occur when the drive is used with conventional industrial electronic circuits and systems. However, a filter is recommended if there is a likelihood of sensitive devices or circuits being installed on the same AC supply or if the motor cable exceeds 75 meters (250 feet). Beyond this length, capacitance to ground will increase the supply emissions. Where it is essential that very low emission levels must be achieved or if conformity with standards is required the optional RFI filter should be used. Refer to Appendix D and instructions included with the filter for installation and grounding information.
RFI Filter Leakage Current The optional RFI filter may cause ground leakage currents. Therefore a solid ground connection must be provided.
ATTENTION: To guard against possible equipment damage, RFI filters can only be used with AC supplies that are nominally balanced with respect to ground. In some installations, threephase supplies are occasionally connected in a 3-wire configuration with one phase grounded (Grounded Delta). The filter must not be used in Grounded Delta supplies.
CE Conformity
Refer to Appendix D.
Installation/Wiring
2-9
GROUNDING
Refer to the grounding diagram on the following page. The drive must be connected to system ground at the power ground (GRD) terminal provided on the power terminal block (TB1). Ground impedance must conform to the requirements of national and local industrial safety regulations (NEC, VDE 0160, BSI, etc.) and should be inspected and tested at appropriate and regular intervals. In any cabinet, a single, lowimpedance ground point or ground bus bar should be used. All circuits should be grounded independently and directly. The AC supply ground conductor should also be connected directly to this ground point or bus bar. Sensitive Currents It is essential to define the paths through which the high frequency ground currents flow. This will assure that sensitive circuits do not share a path with such current, and to minimize the area enclosed by these paths. Current carrying ground conductors must be separated. Control and signal ground conductors should not run near or parallel to a power ground conductor. Motor Cable The ground conductor of the motor cable (drive end) must be connected directly to the ground terminal, not to the enclosure bus bar. Grounding directly to the drive (and filter, if installed) provides a direct route for high frequency current returning from the motor frame and ground conductor. At the motor end,
the ground conductor should also be connected to the motor case ground. If shielded or armored cables are used, the same grounding methods should be used for the shield/armor as well. Discrete Control and Signal Wiring DO NOT connect drive Common terminals (TB2) to ground. DO NOT switch these inputs using non-isolated TTL type circuits. Use dry relay contacts to switch signal inputs to Common. Only isolated 4-20mA sources are recommended. There must be no ground potential difference between source and drive. Safety Ground This is the safety ground required by code. The ground bus can be connected to adjacent building steel (girder, joist) or a floor ground loop, provided grounding points comply with NEC regulations. RFI Filter Important: Using an optional RFI filter may result in relatively high ground leakage currents. The filter must be permanently installed and solidly grounded. Grounding must not rely on flexible cables and should not include any form of plug or socket that would permit inadvertent disconnection. The integrity of this connection should be periodically checked.
2-10
Installation/Wiring
Figure 2.5 Recommended 1305 Grounding for Installation Without EMI Filter (NonCE) Conduit/4-Wire Cable R(L1) Common Mode Core* Shield* U(T1) V(T2) W(T3) GRD T(L3) GRD Ground Rod Shield Motor Terminator* Standard unit has plastic conduit entry. For installation with EMI filter (CE), see Appendix D. Motor Frame
S(L2)
Installation/Wiring
2-11
POWER WIRING
Input and output power connections are performed through a ten position terminal block, TB1 (see page 2-3 for location).
Figure 2.6 Power Terminal Block Designations (TB1)
GRD
GRD
L1 R
L2 S
L3 T
+DC
BRK (DC)
T1 U
T2 V
T3 W
To Motor Required Input Fusing Required Branch Circuit Disconnect AC Input Line
TB1 (0.37-0.75 kW/0.5-1 HP) TB1 (All except above) TB2 (All)
Connection for Dynamic Brake Resistors for all models except the 200-230 Volt, 0.37 to 0.75 kW (0.5 to 1 HP) drive. Important: The [DB Enable] parameter must be enabled for proper operation. For single phase applications, the AC input line can be connected to any two of the three input terminals R, S, T (L1, L2, L3). 1305 drives are UL and cUL listed, and CSA certified as a motor overload protective device. An external overload relay is not required for single motor applications. Important: This drive is not intended for use with single phase motors. Ground from drive to motor frame must be an independent continuous insulated wire run.
2-12
Installation/Wiring
Motor Cables A variety of cable types are acceptable for drive installations. For many installations, unshielded cable is adequate, provided it can be separated from sensitive circuits. As an approximate guide, allow a spacing of 1 meter (3.3 feet) for every 10 meters (33 feet) of length. In all cases, long parallel runs must be avoided. The cable should be 4-conductor with the ground lead being connected directly to the drive ground terminal (GRD) and the motor frame ground terminal. Shielded Cable Shielded cable is recommended if sensitive circuits or devices are connected or mounted to the machinery driven by the motor. The shield must be connected to the drive ground and motor frame ground. The connection must be made at both ends to minimize the external magnetic field. If cable trays or large conduits are to be used to distribute the motor leads for multiple drives, shielded cable is recommended to reduce or capture the noise from the motor leads and minimize cross coupling of noise between leads of different drives. The shield should be connected to the ground connections at both the motor and drive end.
Armored cable also provides effective shielding. Ideally, it should be grounded only at the drive (GRD) and motor frame. Some armored cable has a PVC coating over the armor to prevent incidental contact with grounded structure. If, due to the type of connector, the armor must be grounded at the cabinet entrance, shielded cable should be used within the cabinet to continue as far as possible to the coaxial arrangement of power cable and ground. In some hazardous environments it is not permissible to ground both ends of the cable armor. This is because of the possibility of high current circulating at the input frequency if the ground loop is cut by a strong magnetic field. This only applies in the proximity of powerful electrical machines. In such case, the ground connection at one end may be made through a capacitance, which will block the frequency current but present a low impedance to RF. Because of the highly pulsed nature of the circulating current, the capacitor type used must be rated for AC-to-ground voltage. Consult factory for specific guidelines.
Installation/Wiring
2-13
Conduit If metal conduit is preferred for cable distribution, the following guidelines must be followed. 1. Drives are normally mounted in cabinets and ground connections are made at a common ground point in the cabinet. If the conduit is connected to the motor junction box and at the drive end, no further conduit connections are necessary. 2. No more than three sets of motor leads can be routed through a single conduit. This will minimize cross talk that could reduce the effectiveness of the noise reduction methods described. If more than three drive/motor connections per conduit are required, shielded cable as described above must be used. If practical, each conduit should contain only one set of motor leads.
Motor Lead Lengths Installations with long cable lengths between the 1305 drive and motor may require the use of an output reactor or Terminator. The following guidelines allow for selection of the appropriate drive HP rating (and output reactor or Terminator, if required) to work with an existing motor, and provide motor-lead length solutions for new installations. Voltage doubling at motor terminals, known as reflected wave phenomenon, standing wave or transmission line effect, can occur when using long motor cables with drives. Long motor cables can cause capacitive charging current in excess of the rating of a smaller drive. To ensure proper installation, follow the guidelines provided. All cabling and distances are based on using 14 AWG, 4-conductor type cabling. In general, motors designed and built without phase separating insulation paper between motor windings should be classified as 1000VP-P insulation design. Section A: No Output Reactor or Terminator Table 2.D lists the maximum cable lengths permitted when applying a 460V, 1305 drive to a 460V motor for motor insulation ratings of 1000V, 1200V, and 1600V without an output reactor or Terminator. Shielded and unshielded maximum cable lengths also are listed. Tables are based on operation at nominal line condition (480V).
ATTENTION: To avoid a possible shock hazard caused by induced voltages, unused wires in the conduit must be grounded at both ends. For the same reason, if a drive sharing a conduit is being serviced or installed, all drives using this conduit should be disabled. This will eliminate the possible shock hazard from cross coupled drive motor leads.
2-14
1000V and 1200V Motor Insulation Ratings: Cable lengths listed in Table 2.D are for operating the 1305 drive at a maximum carrier frequency of 4 kHz on motor insulation ratings of 1000V and 1200V. Consult the factory regarding operation above 4 kHz carrier frequency. Multiply listed distances by 0.85 for operation at high line conditions (above 480V). If the maximum cable length used exceeds the distances indicated, refer to Section B. 1600V Motor Insulation Ratings: Cable lengths listed in Table 2.D are based on operating the 1305 drive at a maximum carrier frequency of 2 kHz on motor insulation ratings of 1600V. Consult the factory regarding operation above 2 kHz carrier frequency. Multiply listed distances by 0.55 for operation at high line conditions (above 480V). If the maximum cable length used exceeds the distances indicated, refer to Section B. The Allen-Bradley 1329-HR is representative of 1600VP-P insulation rating designs and is recommended in applications where long cable lengths are required.
Installation/Wiring
2-15
Section B: Use of Output Reactor or Terminator For longer motor-lead length applications, an output reactor or Terminator is required to ensure proper drive operation, and for the motor to operate within its specified insulation rating. The guidelines in Table 2.E are required for proper drive and motor operation, or motor designs without phase-separating insulation paper between motor windings. Applications with non-inverter duty rated motors, with long lead lengths, require an output reactor or Terminator. An output reactor or Terminator helps reduce voltage reflection to the motor to levels which are less than the motor insulation rating. Table 2.E lists maximum cable lengths that can be run when using an output reactor, or one of two available Terminators, for motor insulation ratings of 1000V, 1200V, and 1600V. Shielded and unshielded maximum cable lengths also are listed. When an output reactor is required, locate the reactor at the drive if possible. Consult the factory for applications which require mounting the reactor at the motor. 1000V and 1200V Motor Insulation Ratings: Cable lengths listed in Table 2.E are for operating the 1305 drive at a maximum carrier frequency of 2 kHz on motor insulation ratings of 1000V and 1200V when used with an output reactor or Terminator. Consult the factory regarding operation above 2 kHz carrier frequency. Multiply listed distances by 0.85 for operation at high line conditions (above 480V).
1600V Motor Insulation Ratings: Cable lengths listed in Table 2.E are based on operating the 1305 drive at a maximum carrier frequency of 2 kHz on motor insulation ratings of 1600V. Consult the factory regarding operation above 2 kHz carrier frequency. The Allen-Bradley 1329-HR is representative of 1600VP-P insulation rating designs and is recommended in applications where long cable lengths are required. Example: An existing installation includes a 2 HP, 1200V motor with a 84-meter (275-foot) cable-length requirement between the 1305 drive and the motor. What are the possible solutions to this installation? 1. Table 2.D indicates that either an output reactor or a Terminator is required for this installation example. Consult Table 2.E for output reactor, Terminator, and cable types. 2. Table 2.E suggests these possible solutions: Install a 1305 2-HP drive with an output reactor installed at
the drive, and use unshielded cable.
2-16
Installation/Wiring
Maximum Carrier Frequency High-Line Derating Multiplier 5 5 3 2 3 3 2 1 2 2 1 0.5 1 0.5 1 0.5 0.5
NR = Not Recommended. Important: A 3% reactor reduces motor stress but may cause a degradation of motor waveform quality. Reactors must have a turn-to-turn insulating rating of 2100 volts or higher. Reactors are not recommended for lightly loaded applications because overvoltage trips may result at low output frequencies.
Installation/Wiring
2-17
CONTROL WIRING
Important: All common terminals are tied together within the drive and internally connected to chassis ground. Recommended practice is to run all signal wiring in separate steel conduit.
ATTENTION: Drive can be permanently damaged if any EXTERNAL control voltage is applied to terminals 5 8 and 11 18. DO NOT connect drive Common terminals (TB2) to ground. DO NOT switch these inputs using non-isolated TTL type circuits. Use dry relay contacts to switch signal inputs to Common. Only isolated 4-20mA sources are recommended. There must be no ground potential difference between source and drive.
The factory default control wire scheme is 3 Wire control. The [Input Mode] parameter can be used to program the drive to operate using a two wire Run Forward/Run Reverse control wire scheme. Refer to Chapter 4, Step 10 for programming instructions. Figures 2.7 through 2.10 show the wiring diagrams for the different input modes. Important: If the [Input Mode] is changed, power must be cycled to the drive for the change to take effect. The Start and Reverse functions operate differently for the two different modes.
2-18
Installation/Wiring
Three Wire Control When using this control scheme, the factory default for the reverse function is controlled from TB2. To enable Reverse operation from the HIM or other serial communication adapters, Bit 0 of the [Direction Mask] parameter must be changed from 1 to a 0. See page 5-47. See Chapter 5 for general programming instructions. Two Wire Run Forward/Run Reverse Control To use a two wire Run Forward/Run Reverse control scheme, Bit 0 of the [Direction Mask] must be set to a 1. For proper operation of the Run Forward/Run Reverse mode, install a jumper across terminals 7 and 8 (Stop) and terminals 11 and 12 (Enable). 3W/2nd Acc and Run F/R 2nd A Control The HIM module is limited in the number of characters in the LCD display. Definitions of these functions are as follows. Refer to Chapter 5, Table 5.A for configuration of switches or inputs to TB2. 3w/2nd Acc = Three Wire, 2nd Acceleration Run F/R 2nd A = Run Forward/Reverse, 2nd Acceleration
MOP Function The MOP function is a digital solid-state circuit that produces the same effect as rotating a speed reference potentiometer with a small DC motor. This permits local (HIM) or remote (TB2) control of the command frequency. Important: The drive can still be started from any adapter (HIM or a serial device) and will run at the last commanded direction unless the start, jog and reverse functions of that adapter have been disabled (See [Start Mask], [Direction Mask] and [Jog Mask]. See page 5-47 and 5-48. Important: A stop command can be issued from any adapter at all times. Important: If a Jog is initiated, the drive will Jog in the direction last traveled.
Installation/Wiring Figure 2.7 TB2 Designations [Input Mode] = Three Wire or [Input Mode]=3 w/2nd Acc.
Remote Pot 1
0-10V
2-19
Figure 2.8 TB2 Designations Two Wire Control Operation [Input Mode]=Run Fwd/Rev or [Input Mode]=Run F/R 2nd A
Remote Pot 1
0-10V
Source Wiper or 0-10V DC Input Common 4-20mA Input 0-10V Output Start Common Stop Output #1 11 12 13 14 15 16 17 18 Enable Common Reverse Jog Common SW1 SW2 SW3 (Sink) Output #2 Shield Common Momentary Input Maintained Input Wires must be shielded Run Forward Jumper
User Side
Source Wiper or 0-10V DC Input Common 4-20mA Input 0-10V Output Start Common Stop Output #1 11 12 13 15 16 17 18 Enable Common Reverse Common SW1 SW2 SW3 (Sink) Output #2
2 3 4 5 6 7 8 9 10
2 3 4 5 6 7 8 9 10
User Side
14 Jog
19 20
19 20
2-20
Installation/Wiring Figure 2.10 TB2 Designations Two Wire Control Operation [Input Mode] = Run F/R MOP
Remote Pot 1
0-10V
1
0-10V
Source Wiper or 0-10V DC Input Common 4-20mA Input 0-10V Output Start Common Stop Output #1 11 12 13 15 16 17 18 Enable Common Reverse Common MOP Increment MOP Decrement Frequency Source (Sink) Output #2
2 3 4 5 6 7 8 9 10
User Side
Run Reverse
User Side
Jumper
14 Jog
19 20
Installation/Wiring
2-21
Figure Notes:
Required to operate drive. STOP also used to clear a fault. Use HIM Stop button to clear faults. Contact Closure Input. Internal 5V supply. DO NOT apply external voltage. When the ENABLE signal is lost, the drive output immediately shuts off and the motor will coast to a stop. A Start command will override any Jog command. See Table 5.C on Page 5-31 for more information.
The recommended control signal wire is: D Belden 8760 (or equiv.) - 18 AWG (0.750 mm2), twisted pair, shielded. D Belden 8770 (or equiv.) - 18 AWG (0.750 mm2), 3 conductor, shielded. D Belden 9460 (or equiv.) - 18 AWG (0.750 pair, shielded. mm2), twisted
Recommended practice is to run all signal wiring in a separate steel conduit. The shield wire must only be connected at the drive.
Important: Control inputs to two or more drives must NOT be connected in parallel.
ATTENTION: Signal common is internally connected to chassis ground. Do not use cable shields as signal current paths.
2-22
Installation/Wiring
OUTPUT DEVICES
Drive Output Disconnection ATTENTION: Any disconnecting means wired to drive output terminals U, V and W must be capable of disabling the drive if opened during drive operation. If opened during drive operation, the drive will continue to produce output voltage between U, V, W. An auxiliary contact must be used to simultaneously disable the drive or output component damage may occur.
Table 2.D lists the maximum recommended cable length for unterminated cables, since the voltage doubling phenomenon occurs at different lengths for different drive ratings. If your installation requires longer motor cable lengths, a reactor or cable terminator is recommended. Optional Output Reactor The reactors listed in Catalog A111 can be used for the drive input and output. These reactors are specifically constructed to accommodate IGBT inverter applications with switching frequencies up to 20 kHz. They have a UL approved dielectric strength of 4000 volts, opposed to a normal rating of 2500 volts. The first two and last two turns of each coil are triple insulated to guard against insulation breakdown resulting from high dv/dt. When using output line reactors, it is recommended that the drive PWM frequency be set to its lowest value to minimize losses in the reactors. See Table 2.E. Important: By using an output reactor the effective motor voltage will be lower because of the voltage drop across the reactor this may also mean a reduction of the motor torque. Output Contactor For application of an output contactor to a 1305 drive, please contact Allen-Bradley.
CABLE TERMINATION
Optional Cable Terminator Voltage doubling at motor terminals, known as reflected wave phenomenon, standing wave or transmission line effect, can occur when using drives with long motor cables. Inverter duty motors with phase-to-phase insulation ratings of 1600 volts or higher should be used to minimize effects of reflected wave on motor insulation life. Applications with non-inverter duty motors or any motor with exceptionally long leads may require an output inductor or cable terminator. An inductor or terminator will help limit reflection to the motor, to levels which are less than the motor insulation value.
Installation/Wiring
2-23
ADAPTERS
An adapter is any device connected to the drives serial port. Typical devices include: D Human Interface Modules D Communication Modules D Future adapter devices Important: A maximum of five adapters can communicate to the drive. The total current draw of all adapters should not exceed 250mA. Refer to the data sheet or nameplate of each adapter for the amount of current needed for the adapter to operate. The Adapter address is determined as follows: D Port 1 equals Adapter 1. D Port 2 equals Adapter 2. However, if a splitter is used to expand the number of Adapters to 3, 4 or 5 the splitter will be marked with the appropriate Adapter numbers.
Adapter Mounting Distance The maximum mounting distance between any two adapters connected to the drive is 10 meters. Refer to Figure 2.11.
2-24
Installation/Wiring
Port 2
Male-Male Cable
A
Male-Female Cable
Male-Male Cable
ESC
SEL
Male-Male Cables
ESC
SEL
ESC
SEL
JOG
C
JOG
D
Adapter 3 Communication Module
Chapter
above or Series B version 1.01 and above (see back of HIM), the Status Display, Process Display or Password Login menu can be selected as the power-up display or menu. See appropriate sections on the following pages for more information.
Figure 3.1 Human Interface Module
HIM DESCRIPTION
When the drive mounted HIM is supplied, it will be connected as Adapter 1 (see Adapter in Chapter 2) and visible from the front of the drive. The HIM can be divided into two sections; Display Panel and Control Panel. The Display Panel provides a means of programming the drive and viewing the various operating parameters. The Control Panel allows different drive functions to be controlled. Refer to Figure 3.1 and the sections that follow for a description of the panels. Important: The operation of some HIM functions will depend upon drive parameter settings. The default parameter values allow full HIM functionality.
LCD Display Display Panel Digital Speed Control and Indicator (also available with Analog Speed Pot.) Control Panel
HIM OPERATION
When power is first applied to the drive, the HIM will cycle through a series of displays. These displays will show drive name, HIM ID number and communication status. Upon completion, the Status Display will be shown. This display shows the current status of the drive (i.e. Stopped, Running, etc.) or any faults that may be present (Serial Fault, etc.). If the HIM software is Series A version 3.00 and
From this display, pressing any one of the five Display Panel keys will cause Choose Mode to be displayed. Pressing the Increment or Decrement keys will allow different modes shown in Figure 3.3.
3-2
Display Panel Descriptions Escape When pressed, the ESC key will cause the programming system to go back one level in the menu structure. Select Pressing the SEL key alternately moves the cursor to the next active area. A flashing first character indicates which line is active. Increment/Decrement These keys are used to increment and decrement a value or scroll through different groups or parameters. Enter When pressed, a group or parameter will be selected or a parameter value will be entered into memory. After a parameter has been entered into memory, the top line of the display will automatically become active, allowing another parameter (or group) to be chosen. Control Panel Descriptions Important: The following information is correct as shipped from the factory. Reprogramming of mask parameters can mask out control of some of these functions.
Start The Start key will initiate drive operation if no other control devices are sending a Stop command. This key can be disabled by the [Logic Mask] or [Start Mask]. Stop If the drive is running, pressing the Stop key will cause the drive to stop, using the selected stop mode. Refer to the [Stop Select] in Chapter 5. If the drive has stopped due to a fault, pressing this key will clear the fault and reset the drive. Refer to the [Flt Clear Mode], [Logic Mask] and [Fault Mask] parameters. Jog When pressed, jog will be initiated at the frequency set by the [Jog Frequency] parameter, if no other control devices are sending a Stop command. Releasing the key will cause the drive to stop, using the selected stop mode. Refer to [Stop Select], [Logic Mask] and [Jog Mask]. Important: If the drive is running prior to issuing a jog command, the jog command will be ignored. Important: A start command from another source will override the jog command.
3-3
Control Panel Descriptions (continued) Change Direction Pressing this key will cause the drive to ramp down to 0 Hz and then ramp up to set speed in the opposite direction. The appropriate Direction Indicator will illuminate to indicate the direction of motor rotation. Refer to [Logic Mask] and [Direction Mask]. Note that the factory default for control of the reverse function is the reverse input at the TB2 control terminal block. To enable the HIM control of the reverse function, change Bit 0 of the [Direction Mask] parameter to 0 to disable the reverse function at TB2. Direction LEDs (Indicators) These LEDs illuminate to indicate the direction of motor rotation.
Rotating "Forward"
OFF Steady ON
Increment/Decrement Arrows
(only available with digital speed control)
Pressing these keys will increase or decrease the HIM frequency command. An indication of this command will be shown on the visual Speed Indicator LEDs. The drive will run at this command if the HIM is the selected frequency reference. See [Freq Select 1/2]. Pressing both keys simultaneously stores the current HIM frequency command in HIM memory. The Speed Indicator LEDs will flash momentarily to indicate a successful save (if speed is above 20 percent). Cycling power or connecting the HIM to the drive will set the frequency command to the value stored in HIM memory. If the Analog Speed Potentiometer option has been ordered, the Increment/Decrement keys and Speed Indicator will be replaced by the pot.
Flashing Steady ON
Changing Direction, Decelerating "Reverse," will begin to Accelerate "Forward." Changing Direction, Decelerating "Forward," will begin to Accelerate "Reverse."
Steady ON Flashing
Illuminates in steps to give an approximate visual indication of the commanded speed. If the Analog Speed Potentiometer option has been ordered, the Increment/Decrement keys and Speed Indicator LEDs will be replaced by the pot.
3-4
Important: When the [Logic Mask] bit for an adapter is changed from 1 to 0 it disables all command functions for that adapter with the exception of the Stop command and frequency reference. 1. Lower the hinged panel located below the HIM. 2. Press the retaining lever located directly beneath the HIM, slide the HIM downward and remove it from the drive. 3. To reinsert the HIM, place the top edge of the HIM about 15 mm (1/2 in.) from the top edge of the cover. Push inward on the bottom of the HIM and slide the HIM up into position.
Figure 3.2 HIM Removal
ES C SE L
JO
ES C SE L
JO
Hinged Cover
Retaining Lever
3-5
HIM MODES
The HIM has up to seven different modes. Refer to Figure 3.3. Display When selected, the Display mode allows any of the parameters to be viewed. However, parameter modifications are not allowed. Process The Process mode allows a configurable display to be programmed. One user selected parameter can be displayed with programmed text and scaling. Refer to Chapter 5 for further information. Program Program mode provides access to the complete listing of parameters available for programming. Refer to Chapter 5 for further parameter programming information. EEPROM This mode allows all parameters to be reset to the factory default settings. For Series B HIM Software Version 1.01 and Above, uploading and downloading of drive parameters may be performed.
Search
(Series A HIM, software V3.00 & up or Series B HIM, V1.01 & up Only)
This mode will search for parameters that are not at their default values. Control Status
(Series A HIM, software V3.00 & up or Series B HIM, V1.01 & up Only)
Permits the [Logic Mask] parameter to be disabled/enabled allowing HIM removal while drive power is applied. This menu also provides access to a fault queue which will list the last four faults that have occurred. Trip displayed with a fault indicates the actual fault that tripped the drive. A clear function clears the queue. Important: Clearing the Fault Queue will not clear an active fault. Password The Password mode protects the drive parameters against programming changes by unauthorized personnel. When a password has been assigned, access to the Program and EEPROM modes can only be gained when the correct password has been entered. The password can be any five digit number between 00000 and 65535. Refer to the example on page 3-17.
3-6
OPERATOR LEVEL
or
This flow chart serves as a guide to the key strokes required for movement throughout the menu levels.
or
SEL
or
or
"Choose Mode"
Display
(Read Only)
Process
Program
(Read/Write)
EEPROM
Search
(Read Only)
Control Status
Password
Process Display
Reset Defaults Upload Parameters Download Parameters Recall Values Save Values
Access to the Program and EEPROM modes, and the Control Logic and Clear Fault Queue, will be disabled if the password is Logged out. Series A HIM Software Version 3.00 and Above or Series B HIM Software Version 1.01 and Above only. Series B HIM Software Version 1.01 and Above only.
PARAMETER LEVEL
3-7
1. The Display and Program modes allow access to the parameters for viewing or programming. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
or
Choose Mode Display
b. Press the Increment (or Decrement) key to show Program (or Display). c. Press Enter.
or
d. Press the Increment (or Decrement) key until the desired group is displayed. e. Press Enter.
or
f. Press the Increment (or Decrement) key to scroll to the desired parameter.
3-8
Changing Digits
2. With Series A HIM software versions 3.00 and above, or Series B HIM software version 1.01 and above, you have the ability to access and modify each individual bit or digit. Important: This procedure assumes the Password is not set, you have already logged in, or the device has been set to Defaults. a. Select a parameter with Increment (or Decrement) keys. b. Press the SEL key to view the first bit. Pressing this key again will move the cursor to the left one bit or digit. Individual bits of a Read/Write parameter can be changed. Pressing the SEL key will move the cursor (flashing character) one bit to the left. That bit can then be changed by pressing the Increment/Decrement keys. When the cursor is in the far right position, pressing the Increment/Decrement keys will increment or decrement the entire value.
Choose Group Setup Accel Time 99.9 Secs
or
SEL
Flashing = Modify
3-9
Bit ENUMs
3. With Series A HIM software versions 3.00 and above, or Series B HIM software version 1.01 and above, bit ENUMs (16 character text strings) will be displayed to aid interpretation of bit parameters. a. From the Choose Group menu, use the Increment/Decrement key to select the Masks group. Press Enter. b. Press the SEL key to view the ENUM of the first bit. Pressing this key again will move the cursor to the left one bit or digit and view the next bits ENUM.
Choose Group Mask Adapter 4 X1111111
or
SEL
Flashing
3-10
PROCESS MODE
ACTION DESCRIPTION HIM DISPLAY
1. When selected, the Process mode will show a custom display consisting of information programmed with the Process Display group of parameters. a. Complete steps a c on page 3-7 to access the Program mode.
or
Choose Mode Program Choose Group Process Display Process Par 1
b. Press the Increment/Decrement key until Process Display is shown. Press Enter. c. Using the Increment/Decrement keys, select [Process Par] and enter the number of the parameter you wish to monitor. Press Enter. d. Select [Process Scale] using the Increment/Decrement keys. Enter the desired scaling factor. Press Enter. e. Select [Process Text 1] using the Increment/Decrement keys. Enter the desired text character. Press Enter & repeat for the remaining characters.
or
or
or
or
ESC
Process Text 1 V
f. When process programming is complete, press ESC until Choose Mode is displayed. Press Increment/Decrement until Process is displayed. Press Enter to get process value. g. With Series A HIM Software Versions 3.00 and above or Series B HIM Software Versions 1.01 and above. the user has the ability to save the Process Display for power up. To do this, simultaneously press Increment and Decrement keys on programming panel.
press
ESC SEL
+0.00 V
3-11
EEPROM MODE
ACTION DESCRIPTION HIM DISPLAY
Reset Defaults
1. The EEPROM mode is used to restore all settings to factory default values or to upload or download parameters between the HIM and the drive. (Parameter upload or download requires a Series B HIM). To restore factory defaults: a. From the Status Display, press Enter (or any key). Choose Mode will be displayed.
Choose Mode Display
or
b. Press the Increment (or Decrement) key until EEPROM is displayed. If EEPROM is not in the menu, programming is password protected. Refer to Password Mode later in this section. c. Press Enter.
or
d. Press the Increment (or Decrement) key until Reset Defaults is displayed. e. Press Enter to restore all parameters to their original factory settings.
ESC
f. Press ESC. Reprogram Fault will display. g. Press the Stop key to reset the fault. Important: If [Input Mode] was previously set to a value other than 1, cycle drive power to reset.
3-12
Drive HIM
2. To upload a parameter profile from the drive to the HIM, you must have a Series B HIM. a. From the EEPROM menu, press the Increment/Decrement keys until Drive HIM is displayed. b. Press Enter. Use the Increment/Decrement keys to choose between profile 1 or profile 2.
EEprom DriveHIM
or
DriveHIM 1 DriveHIM 1 A
SEL
or
c. To give a profile a name, use the SEL key to move the cursor right and use the Increment/Decrement keys to change the characters. When done, press Enter to save the name. d. Press Enter. An informational display will be shown, indicating the drive type and firmware version. e. Press Enter to start the upload. The parameter number currently being uploaded will be displayed on line 1 of the HIM. Line 2 will indicate total progress. Press ESC to stop the upload. f. A successful upload will be indicated by Completed displayed on line 2 of the HIM. Press Enter. If Error is displayed, see Chapter 6.
DriveHIM 45 |||||
3-13
HIM Drive
3. To download a parameter profile from the HIM to the drive, you must have a Series B HIM. Important: The download function will only be available when there is a valid profile stored in the HIM.
or
a. From the EEPROM menu, press the Increment/Decrement keys until HIM Drive is displayed. b. Press the Enter key. A profile name will be displayed on line 2 of the HIM. Pressing the Increment/Decrement keys will scroll the display to a second profile (if available). c. Once the desired profile name is displayed, press the Enter key. An informational display will be shown, indicating the version numbers of the profile and drive. d. Press Enter to start the download. The parameter number currently being downloaded will be displayed on line 1 of the HIM. Line 2 will indicate total progress. Press ESC to stop the download. e. A successful download will be indicated by Completed displayed on line 2 of the HIM. Press Enter. If Error is displayed, see Chapter 6.
EEprom HIMDrive
HIMDrive 1
or
HIMDrive 45 |||||
3-14
SEARCH MODE
ACTION DESCRIPTION HIM DISPLAY
Search
1. The Search mode is only available with Series A HIM software version 3.00 and above or Series B HIM software version 1.01 and above. This mode allows you to search through the linear parameter list and display all parameters that are not at the factory default values. The Search mode is a read only function. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
Choose Mode Display
or
b. Press the Increment (or Decrement) key until Search is displayed. c. Press Enter. The HIM will search through all parameters and display any parameters that are not at their factory default values.
or
d. Press the Increment (or Decrement) key to scroll through the list.
3-15
Control Logic
1. The Control Status mode is only available with Series A HIM software version 3.00 and above or Series B HIM software version 1.01 and above. This mode allows the drive logic mask to be disabled, thus preventing a Serial Fault when the HIM is removed with drive power applied. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
Choose Mode Display
or
b. Press the Increment (or Decrement) key until Control Status is displayed. Press Enter. c. Select Control Logic using the Increment/Decrement keys. Press Enter.
or
or
SEL
d. Press the SEL key, then use the Increment (or Decrement) key to select Disabled (or Enable). e. Press Enter. The logic mask is now disabled (or enabled).
3-16
2. This menu provides a means to view the fault queue and clear it when desired. a. From the Control Status menu, press the Increment (or Decrement) key until Fault Queue is displayed. b. Press Enter.
Control Status Fault Queue
or
c. Press Increment (or Decrement) key until View Faults is displayed. d. Press Enter. The fault queue will be displayed. Trip displayed with a fault will indicate the fault that tripped the drive.
or
ESC
e. Use the Increment (or Decrement) key to scroll through the list.
or
f. To clear the fault queue, press ESC. Then use the Increment/Decrement keys to select Clear Queue. Press Enter. Important: Clearing the Fault Queue will not clear an active fault.
3-17
PASSWORD MODE
ACTION DESCRIPTION HIM DISPLAY
Setting Password
1. The factory default password is 0 (which disables password protection). To change the password and enable password protection, perform the following steps. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
Choose Mode Display
or
b. Press the Increment (or Decrement) key until Password is displayed. c. Press Enter.
Login Modify
or
d. Press the Increment (or Decrement) key until Modify is displayed. e. Press Enter. Enter Password will be displayed.
Password Modify Enter Password < 0> Enter Password < 123>
or
SEL
f. Press the Increment (or Decrement) key to scroll to your desired new password. With Series A HIM software versions 3.00 and above or Series B HIM software version 1.01 and above, the SEL key allows each digit to be selected and changed individually. g. Press Enter to save your new password. h. Press Enter again to return to the Password Mode.
Login is used to enter the password for access to the Program, Control Logic, Clear Fault Queue, and EEPROM modes.
3-18
DESCRIPTION
HIM DISPLAY
Password Logout Choose Mode Password
or
i. Press the Increment (or Decrement) key until Logout is displayed. j. Press Enter to log out of the Password mode.
k. With Series A HIM software versions 3.00 and above or Series B HIM software version 1.01 and above, the Password Login menu can be programmed to appear when drive power is applied. To save the Password Login menu as the power-up menu, simultaneously press the Increment and Decrement keys while the Password display is active.
Logout is used to disable access to the Program, Control Logic, Clear Fault Queue, and EEPROM modes.
3-19
2. The Program and EEPROM modes, and the Clear Fault Queue menu, are now password protected and will not appear in the menu. To access these modes, perform the following steps. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
or
b. Press the Increment (or Decrement) key until Password is displayed. c. Press Enter. Login will be displayed. d. Press Enter, Enter Password will be displayed.
Choose Mode Password Password Login Enter Password < 0> Enter Password < 123>
or
e. Press the Increment (or Decrement) key until your correct password is displayed. With Series A HIM software versions 3.00 and above or Series B HIM software version 1.01 and above, the SEL key allows each digit to be selected and changed individually. f. Press Enter. g. The Program and EEPROM modes will now be accessible. To prevent future access to program changes, Logout as described in step 3.
3-20
Logout from the Drive 3. To prevent unauthorized changes to parameters, Logout must be performed as described below. a. From the Status Display, press Enter (or any key). Choose Mode will be shown.
or
b. Press the Increment (or Decrement) key until Password is displayed. c. Press Enter.
Choose Mode Password Password Login Password Logout Choose Mode Password
or
d. Press the Increment (or Decrement) key until Logout is displayed. e. Press Enter to log out of the Password mode.
StartUp
CHAPTER OBJECTIVES
This chapter describes the steps needed to start-up the drive. Included in the procedure are typical adjustments and checks to assure proper operation. The information contained in previous chapters of this manual must be read and understood before proceeding. Important: The drive is designed so that start-up is simple and efficient. The programmable parameters are grouped logically so that most start-ups can be accomplished by adjusting parameters in only one group. Advanced features and adjustments are grouped separately. This eliminates having to step through unneeded parameters on initial start-up. This start-up procedure covers only those most commonly adjusted values, all of which appear in the Setup Group.
Chapter
ATTENTION: Power must be applied to the drive to perform the following start-up procedure. Some of the voltages present are at incoming line potential. To avoid electric shock hazard or damage to equipment, only qualified service personnel should perform the following procedure. Thoroughly read and understand the procedure before beginning. If an event does not occur while performing this procedure, Do Not Proceed. Remove Power by opening the branch circuit disconnect device and correct the malfunction before continuing.
Important: D Power must be applied to the drive when viewing or changing parameters. Previous programming may effect the drive status when power is applied. D Confirm that all circuits are in a de-energized state before applying power. User supplied voltages may exist at TB2 even when power is not applied to the drive. D Refer to Chapter 6 for fault code information.
START-UP PROCEDURE
The following start-up procedure is written for users who have a Human Interface Module (HIM) installed in the drive (Port 1). For users without a HIM, external commands and signals must be substituted. Important: The parameters in the Set Up Group (page 5-8) should be reviewed and reprogrammed as necessary for basic operation.
4-2
Start-Up
Initial Operation - Motor Disconnected 1.Verify that AC line power at the disconnect device is within the rated value of the drive. 2.Disconnect and lock-out all incoming power to the drive including incoming AC power to terminals L1, L2 and L3 (R, S and T) plus any separate control power for remote interface devices. Remove the drive cover and verify the motor leads are disconnected from the Power Terminal Block (TB1), terminals T1, T2 and T3 (U, V, W). Refer to Chapter 2 for terminal location.
ATTENTION: Proceed with caution. A DC bus voltage may be present at the Power Terminal Block (TB1) even when power is removed from the drive.
3.Verify that the Stop and Enable inputs are connected. 4.Confirm that all other optional inputs are connected to the correct terminals and are secure. 5.If the HIM has a Control Panel, use the local controls to complete the start-up procedure. If a Control Panel is not present, remote devices must be used to operate the drive. 6.Replace the drive cover.
ACTION
Apply Power to Drive
DESCRIPTION
HIM DISPLAY
7. When power is first applied to the drive, the following information will be momentarily displayed: a.) The HIM ID# (Adapter #) and firmware version number. b.) Communication status.
c.) Series letter of drive is displayed. d.) The LCD Display should light and display a drive status of Stopped and an output frequency of +0.00 Hz.
Start-Up
4-3
8. If the HIM and drive are not communicating properly, Connection Fail may be displayed on line 2. If this occurs remove the HIM from the drive and reinsert. See Page 3-4 for HIM Removal instructions. If this does not correct the problem or another fault message is displayed, record the information and remove all power. Determine and correct the fault source before proceeding. Refer to Chapter 6 for fault descriptions.
Reset Factory Defaults
9. Important: The remaining steps in this procedure are based on factory default parameter settings. If the drive has been previously operated, parameter settings may have been changed and may not be compatible with this start-up procedure or application. Refer to page 3-11 to reset to factory defaults. 10. The factory default [Input Mode] is 3 wire control as described in Chapter 2. If the factory default setting is sufficient, then skip to Step 11. If another control scheme is desired, change the [Input Mode] parameter by performing the following procedure.
4-4
Start-Up
10. INPUT MODE SELECTION (continued) a.) From the Status Display, press the Enter key (or any key). Choose Mode will be displayed. b.) Press the Increment (or Decrement) key until Program is displayed. c.) Press Enter. The parameter group Metering will be displayed. d.) Press the Increment key again until the Set Up Group is displayed. e.) Press Enter.
or
SEL
Choose Mode Display Choose Mode Program Choose Group Metering Choose Group Set Up
f.) Press the Increment or Decrement key until the [Input Mode] parameter is displayed. g.) Press SEL. The first character of line 2 will now flash. h.) Press the Increment or Decrement key until the correct mode is displayed, then press enter. The first character of line 1 should now be flashing. i.) Press the ESC key (3 times) to return to the Status Display. Important: If the [Input Mode] is changed, power must be cycled for the change to take effect.
or
ESC
Stopped +0.00 Hz
Start-Up
4-5
11. Setting Frequency Command to 0 Hz If the HIM has an analog potentiometer option, turn the potentiometer fully counter clockwise and skip to Step 12. If the HIM has Digital Up-Down keys for frequency control then perform the following: a.) From the Status Display, press the Enter key (or any key). Choose Mode will be displayed.
or
Choose Mode Program Choose Mode Display Choose Group Set Up Choose Group Metering Output Current 0.00 Amps Freq Command +0.00 Hz
b.) Press the Increment or Decrement key until Display is shown. c.) Press Enter.
or
d.) Press the Increment or Decrement key again until Metering is displayed. e.) Press Enter.
or or
ESC
f.) Press the Increment or Decrement key until [Freq Command] is displayed. g.) If the frequency command is a value other than 0 Hz, use the speed source (digital up-down keys on Control Panel) to set the command to 0 Hz. h.) After the command has been set to 0 Hz, press the ESC key until the Status Display is shown.
Stopped +0.00 Hz
4-6
Start-Up
12. Verifying Minimum and Maximum Frequency Settings. a.) Press the Start key. The drive should output 0 Hz. which is the factory default value for the [Minimum Freq] parameter. The Status Display should indicate At Speed and the actual frequency (+0.00 Hz.).
or
At Speed +0.00 Hz
b.) With the drive still running, use the speed source to command maximum speed. The drive should ramp to 60 Hz. which is the factory default value for the [Maximum Freq] parameter.
13. Enable interlock check. The following steps check for correct drive operation when the Enable input is removed. Refer to Chapter 2 for terminal designations. a.) With the drive still running, open the Enable signal. The drive should stop and indicate Not Enabled on the Display Panel. Restore the Enable signal. b.) Restart the drive by pressing the Start key.
At Speed +60.00 Hz
Accelerating +10.00 Hz
Stopped +0.00 Hz
Start-Up
4-7
a.) With the drive stopped, press and hold the JOG key on the Control Panel. The drive should accelerate to the frequency programmed by the [Jog Frequency] parameter and remain there until the JOG key is released. When released, the drive should Ramp to Stop which is the factory default stopping method for the [Stop Select] parameter. 15. Checking Accel and Decel Times. a.) Start the drive and use the speed source to command maximum frequency. b.) Press the Stop key and estimate the amount of time the drive takes to decelerate from 60 Hz to 0 Hz. This time should equal the time set in the [Decel Time l] parameter (default is 10 seconds). If these times are not correct for your application, refer to Chapter 5 for instructions on programming changes. c.) Start the drive and estimate the amount of time the drive takes to accelerate to maximum frequency. This should equal l0 seconds, which is the factory default value for the [Accel Time 1] parameter. d.) Stop the drive.
Accelerating +10.00 Hz At Speed +60.00 Hz Decelerating +30.00 Hz Stopped +0.00 Hz Accelerating +10.00 Hz At Speed +60.00 Hz
4-8
Start-Up
ATTENTION: Proceed with caution. A DC Bus Voltage may be present at the Power Terminal Block (TB1) even when power is removed from the drive.
a.) Disconnect and lock-out all input and control power to the drive. When the HIM Display is no longer illuminated, remove the drive cover. b.) Verify that the DC Bus neon indicator is not illuminated (See Figure 2.3 for location) and wait 60 seconds. Reconnect the motor leads to the drive and replace the drive cover. Important: The parameters in the Set Up Group (page 5-8) should be reviewed and reprogrammed as necessary for basic operation. ATTENTION: In the following steps, rotation of the motor in an un-desired direction can occur. To guard against possible equipment damage, it is recommended that the motor be disconnected from the load before proceeding.
4-9
17. Check for Correct Motor Rotation. a.) Reapply power to the drive. b.) Verify that the frequency command is at zero Hz. Refer to step 11 for further information. c.) Start the drive.
At At Speed Speed +5.00 +5.00 Hz Hz
d.) Slowly increase the speed until the motor begins to turn. Check the direction of motor rotation.
e.) Stop the drive. If the direction of rotation is as desired, proceed to step 18. If the direction of rotation is incorrect - disconnect and lock-out all input and control power to the drive. When the HIM Display is no longer illuminated, remove the drive cover. Verify that the DC Bus neon indicator is not illuminated (see Figure 2.3 for location) and wait 60 seconds. Interchange any two of the three motor leads at TB1 terminals, T1, T2 or T3. Replace the drive cover and repeat steps a e to verify correct motor rotation.
4-10
Start-Up
At Speed +5.00 Hz
b.) Slowly increase the speed. Check for proper motor operation throughout the speed range.
At Speed +60.00 Hz
c.) Press the Stop key. 19. This completes the basic start-up procedure. Depending on your application, further parameter programming may be required. Refer to Chapter 5 for information. Important: The parameters in the Set Up Group (page 5-8) should be reviewed and reprogrammed as necessary for basic operation.
Stopped +0.00 Hz
Programming
CHAPTER OBJECTIVES
Chapter 5 describes the 1305 parameters which are divided into groups for ease of programming and operator access. Grouping replaces a sequentially numerical parameter list with functional parameter groups that increases operator efficiency and helps to reduce programming time. For most applications, this means simplicity at startup with minimum drive tuning.
Function Accel/Decel Time Accel/Decel Selection Analog Invert Auto-Restart/ Run On Power Up Current Limiting Custom Volts/Hz DC Boost DC Brake-to-Stop Fan/Pump Volts/Hz Fault Buffer History Frequency Select Freq. Source Select Line Loss Fault Page # 5-9 5-30 5-21 5-32 5-11, 5-13 5-17 5-17, 5-18, 5-19 5-22, 5-23 5-18 5-39 5-25 5-29 5-40, 5-41 Function Min/Max Freq. MOP
Chapter
Page #
5-10, 5-11, 5-15 5-6, 5-8, 5-28, 5-49, 5-53 5-37 5-12 5-25, 5-27, 5-29 5-55 5-20 5-22 5-33, 5-34 5-27, 5-28 5-18 5-16 5-19
Output Configuration Overload Protection Preset Frequencies Process Display PWM Freq. Derating Ramp to Stop S-Curve Acceleration Skip Frequencies Standard Boost V/Hz Standard Volts/Hz Start/Run Boost
CHAPTER CONVENTIONS
1. All parameters required for any given drive function will be contained within a group, eliminating the need to change groups to complete a function. 2. To help differentiate parameter names and display text from other text in this manual, the following conventions will be used Parameter Names will appear in [Brackets] Display Text will appear in Quotes. 3. Parameter information in this chapter is presented for users who have a Human Interface Module (HIM) installed. For those users without a HIM installed, the drive can be operated using the factory default values for each parameter or parameter values can be changed through the serial port.
FUNCTION INDEX
The Function Index shown provides a directory of various drive functions. The Page Number will direct you to the parameters associated with each function.
5-2
Programming
Metering
Page 5-5
Output Current (54) Output Voltage (1) Output Power (23) DC Bus Voltage (53) Output Freq (66) Freq Command (65) MOP Hz (42) Drive Temp (70) Last Fault (4) % Output Power (3) % Output Curr (2)
Setup
Page 5-8
Input Mode (21) Freq Select 1 (5) Accel Time 1 (7) Decel Time 1 (8) Base Frequency (17) Base Voltage (18) Maximum Voltage (20) Minimum Freq (16) Maximum Freq (19) Stop Select (10) Current Limit (36) Overload Mode (37) Overload Current (38) Sec Curr Limit (141) Adaptive I Lim (149)
Advanced Setup
Page 5-15
Minimum Freq (16) Maximum Freq (19) Base Frequency (17) Base Voltage (18) Break Frequency (49) Break Voltage (50) Maximum Voltage (20) DC Boost Select (9) Start Boost (48) Run Boost (83) PWM Frequency (45) Analog Invert (84) 4-20 mA Loss Sel (81) Stop Select (10) DC Hold Time (12) DC Hold Volts (13) DB Enable (11) Motor Type (41) Compensation (52)
Frequency Set
Page 5-25
Freq Select 1 (5) Freq Select 2 (6) Jog Frequency (24) Prst/2nd Accel (26) Upper Presets (72) Accel Time 2 (30) Decel Time 2 (31) Preset Freq 1 (27) Preset Freq 2 (28) Preset Freq 3 (29) Preset Freq 4 (73) Preset Freq 5 (74) Preset Freq 6 (75) Preset Freq 7 (76) Skip Freq 1 (32) Skip Freq 2 (33) Skip Freq 3 (34) Skip Freq Band (35) MOP Increment (22) Analog Filter (144)
Feature Select
Page 5-32
Run On Power Up (14) Reset/Run Tries (85) Reset/Run Time (15) S Curve Enable (57) S Curve Time (56) Language (47) Cable Length (143) Rated Slip (146) Slip Comp Adder (148) IR Comp % (147)
Output Configuration
Page 5-37
Output 1 Config (90) Output 2 Config (91) Analog Out Sel (25) Above Freq Val (77) Above Curr Val (142)
Faults
Page 5-39
Fault Buffer 0 (86) Fault Buffer 1 (87) Fault Buffer 2 (88) Fault Buffer 3 (89) Clear Fault (51) Cur Lim Trip En (82) Line Loss Fault (40) Flt Clear Mode (39)
Programming
5-3
Wrap to Metering
Diagnostics
Page 5-42
Drive Command (58) Drive Status (59) Drive Alarm (60) Input Status (55) Freq Source (62) Freq Command (65) Drive DIrection (69) Motor Mode (43) Power Mode (44) Drive Type (61) Firmware Ver (71) Output Pulses (67) Drive Temp (70) Set Defaults (64)
Masks
Page 5-47
Logic Mask (92) Direction Mask (94) Start Mask (95) Jog Mask (96) Reference Mask (97) Accel Mask (98) Decel Mask (99) Fault Mask (100) MOP Mask (101) Local Mask (93)
Owners
Page 5-50
Stop Owner (102) Direction Owner (103) Start Owner (104) Jog Owner (105) Reference Owner (106) Accel Owner (107) Decel Owner (108) Fault Owner (109) MOP Owner (110) Local Owner (137)
Adapter I/O
Page 5-54
Data In A1 (111) Data In A2 (112) Data In B1 (113) Data In B2 (114) Data In C1 (115) Data In C2 (116) Data In D1 (117) Data In D2 (118) Data Out A1 (119) Data Out A2 (120) Data Out B1 (121) Data Out B2 (122) Data Out C1 (123) Data Out C2 (124) Data Out D1 (125) Data Out D2 (126)
Process Display
Page 5-55
Process Par (127) Process Scale (128) Process Txt 1 (129) Process Txt 2 (130) Process Txt 3 (131) Process Txt 4 (132) Process Txt 5 (133) Process Txt 6 (134) Process Txt 7 (135) Process Txt 8 (136)
Linear List
Page 5-56
This group contains all parameters listed in numerical order.
5-4
Programming
PROGRAMMING EXAMPLE
The following is an example of the programming steps required to change a parameter setting. In this example, the parameter [Freq Select 1] is being programmed from its factory default setting of Adapter 1 to a new setting, Adapter 2.
ACTION
ESC SEL
DESCRIPTION
HIM DISPLAY
Stopped +0.00 Hz
1. Press any key to go from the Status Display to the Choose Mode menu.
or
To Select Mode
2. Press the Up/Down keys until Program appears on the display. 3. Press the Enter key to go to the Program menu.
Choose Mode Program
To Select a Group
or
4. Press the Up/Down keys until Setup appears on the display. 5. Press the Enter key to go to the Setup menu. 6. Press the Up/Down keys until [Freq Select 1] appears on the display. 7. Press the SEL key. The first character of line 2 will flash indicating the parameter setting/value can be changed. 8. Press the Up/Down keys until Adapter 2 appears on the display. 9. Press the Enter key to program [Freq Select 1] to Adapter 2.
Freq Select 1 Adapter 2 Freq Select 1 Remote Pot
or
SEL
or
Programming
5-5
Metering
This group of parameters consists of commonly viewed drive operating conditions such as drive output frequency, output voltage, output current and command frequency. All parameters in this group are Read Only.
[Output Current]
This parameter displays the output current present at TB1, terminals T1, T2 & T3 (U, V & W).
Factory Default None Minimum 0.00 Maximum Two Times Drive Output Current
[Output Voltage]
This parameter displays the output voltage present at TB1, terminals T1, T2 & T3 (U, V & W)
[Output Power]
This parameter displays the output power present at TB1, terminals T1, T2, & T3 (U, V & W).
Factory Default None Minimum 0 Maximum Two Times Rated Drive Output Power
Factory Default None Minimum 0 Maximum 410 - 230V Drive 815 - 460V Drive
5-6
Programming
[Freq Command]
This parameter displays the frequency that the drive is commanded to output. This command may come from any one of the frequency sources selected by [Freq Select 1], [Freq Select 2] or [Preset Freq 1-7] the preset speeds 1-7 as determined by the inputs to SW1, SW2, and SW3 at TB2.
[MOP Hz]
This parameter displays the frequency reference commanded by the Motor Operated Potentiometer (MOP) function. This MOP frequency command can be adjusted from TB2-16 and TB2-17 if the appropriate [Input Mode] is selected. This MOP frequency command can also be changed through serial communication. This value is displayed regardless of whether or not this is the active frequency command.
Programming
5-7
[Last Fault]
This parameter displays the fault code for the present drive fault. If there is no active fault, the value will be zero.
[% Output Power]
This parameter displays the percent of drive rated output power.
Factory Default None Minimum 0 % Maximum 200% Drive Rated Power Factory Default None Minimum 0 % Maximum 200% of Rated Drive Output Current
[% Output Curr]
This parameter displays the percent of drive rated output current.
5-8
Programming
Setup
This group of parameters defines the basic operation of the drive and should be programmed before initial operation. For advanced programming and information on specific parameters, refer to the flow chart on page 5-2 & 5-3
Parameter # 21 Parameter Type Read & Write Units Text Factory Default Three Wire Setting Three Wire Run Fwd/Rev 3 W/2nd Acc (2nd Accel) Run F/R 2nd A (2nd Accel) 3 Wire/MOP Run F/R MOP Important:This parameter cannot be programmed while the drive is running.
[Input Mode]
This parameter selects between Three Wire and Run Fwd/Rev control. Refer to Chapter 2, Figure 2.7 through Figure 2.10. Important: Power must be cycled to the drive for the change to take effect. Important:See Frequency Set Group for MOP explanation.
[Freq Select 1]
This parameter is the factory default parameter for selecting the frequency source that will supply the [Freq Command] to the drive. [Freq Select 2] or [Preset Freq 17] can be selected in place of this parameter with proper terminal block inputs. (See Chart on Page 5-29). Important: If an adapter that is not connected is selected as the active frequency source, the drive will fault on Hz Sel Fault (F30).
Factory Default Adapter 1 Settings Remote Pot 0-10 0 10 Volt 420 mA MOP Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6
Programming
5-9
[Decel Time 1]
This parameter is the factory default parameter for determining the time it will take the drive to ramp from [Maximum Frequency] to 0 Hz. The rate is linear unless [S Curve] is Enabled or [Stop Select] is set to S-Curve. It applies to any decrease in command frequency. The [Decel Time 2] parameter can be selected in place of this parameter. (See Chart on Page 5-30).
Factory Default 10.0 Sec Minimum 0.0 Sec Maximum 3600.0 Sec
Speed
Time
a Decel '
Time
5-10
Programming
[Base Voltage]
This value should be set to the motor nameplate Rated Voltage.
Factory Default Max. Drive Rated Volts Minimum 25% of Max. Drive Rated Volts Maximum 100% of Max. Drive Rated Volts
[Maximum Voltage]
This parameter sets the highest voltage the drive will output.
Factory Default Max. Drive Rated Volts Minimum 25% of Max. Drive Rated Voltage Maximum 110% of Max. Drive Rated Volts
[Minimum Freq]
This parameter sets the lowest frequency the drive will output. Important: All analog inputs to the drive (4-20mA, 0-10V, Remote Pot) are scaled for the range [Minimum Freq] to [Maximum Freq].
Important: This parameter can not be programmed while the drive is running.
Programming
5-11
Important: This parameter can not be programmed while the drive is running.
[Stop Select]
This parameter selects the stopping mode when the drive receives a valid stop command.
DC Brake
S-Curve
[Current Limit]
This parameter sets the maximum drive output current that is allowed before current limiting occurs. Important: If a value is programmed into the [Sec Curr Limit] parameter then that value will be the active current limit value at speeds above 1.5 times [Base Frequency]. See Fig. 5.5. [Output 1 Config] and [Output 2 Config] can be set to alarm to indicate an overload condition exists.
Factory Default 150 % of Drive Rated Current Minimum 20 % of Drive Rated Current Maximum 150% of Drive Rated Current Important: See [Cur Lim Trip En] on page 5-40.
The Drive Rated Ouput Current is based on three phase input ratings. See page 5-13 for instructions for Single Phase Input Ratings.
5-12
Programming
[Overload Current]
This value should be set to the motor nameplate Full Load Amps (F.L.A.).
Factory Default 115% of Drive Rated Current Minimum 20% of Drive Rated Current Maximum 115% of Drive Rated Current
Programming
5-13
5-14
Programming
Programming
5-15
Advanced Setup
This group contains parameters that are required to setup advanced functions of the drive such as custom Volts per Hertz settings and dynamic braking.
[Minimum Freq]
This parameter sets the lowest frequency the drive will output. Important: All analog inputs to the drive (4-20mA, 0-10V, Remote Pot) are scaled for the range [Minimum Freq] to [Maximum Freq].
Factory Default 0 Hz Minimum 0 Hz Maximum 120 Hz Important: This parameter can not be programmed while the drive is running.
[Maximum Freq]
This parameter sets the highest frequency the drive will output. Important: All analog inputs to the drive (4-20mA, 0-10V, Remote Pot) are scaled for the range [Minimum Freq] to [Maximum Freq]
Factory Default 60 Hz Minimum 40 Hz Maximum 400 Hz Important: This parameter can not be programmed while the drive is running.
[Base Frequency]
This value should be set to the motor nameplate Rated Frequency.
5-16
Programming
a [Maximum Voltage]
[Maximum Frequency]
Voltage
0 0
Frequency
y Motor Rated
[Break Frequency]
This parameter sets a midpoint frequency on a custom Volts-per-Hz curve. Combined with [Break Voltage], this value determines the Volts-per-Hz ratio between 0 and [Break Frequency]. Important: [DC Boost Select] must be set to Break Point for this parameter to be active.
Programming
5-17
[Maximum Voltage]
Sets the highest voltage the drive will output. Important: [Maximum Voltage] does not have to be set greater than [Base Voltage], but the maximum drive output is limited to [Maximum Voltage].
Factory Default Max. Drive Rated Volts Minimum 25% of Max. Drive Rated Volts Maximum 110% of Max. Drive Rated Volts
a [Maximum Voltage]
[Maximum Frequency]
This pattern is active only when [DC Boost Select] is set to Break Point. The following guidelines should be followed when setting up a custom Volts-per-Hz curve: 1. [Base Voltage] must be greater than [Start Boost]. 2. If [DC Boost Select] is set to Break Point then: [Base Voltage] must be greater than [Break Voltage] and [Break Voltage] must be greater than [Start Boost].
Voltage
Start Boost ' 0 0
Frequency
5-18
Programming
a [Maximum Voltage]
[Maximum Frequency]
Voltage
Voltage
48 45% Base Voltage 35% Base Voltage
6 No Boost 0 0
Frequency
y Motor Rated
0 0
Programming
5-19
[Run Boost]
This parameter sets the DC boost level for constant speed level when [DC Boost Select] is set to Run Boost. [Run Boost] must be set at a value less than [Start Boost].
Factory Default 0 Volts Minimum 0 Volts Maximum 25% of Max. Drive Rated Volts
5-20
Programming
Programming
5-21
Drive Output
Enabled [Minimum Frequency] ' y 0V 4 mA y 10 V 20 mA
5-22
Programming
Factory Default 0.0 Sec Minimum 0.0 Sec Maximum 150 Sec
Time
Time
Programming
5-23
[DB Enable]
This parameter enables the use of external dynamic brake resisters by disabling the internal ramp regulation regulation. Important: Dynamic braking is not available for 0.37 - 0.75 kW (0.5 - 1HP) units rated 230 Volt.
[Motor Type]
Factory default for this parameter is an induction motor. Changing this parameter to Sync Sync PM PM causes [Compensation] and [Rated Slip] to be internally disabled.
5-24
Programming
Programming
5-25
Frequency Set
This group of parameters allows the user to program the frequency source, frequency settings, accel/decel times and skip frequencies of the drive.
[Freq Select 1]
This parameter is the factory default parameter for selecting the frequency source that will supply the [Freq Command] to the drive. [Freq Select 2] or [Preset Freq 1-7] can be selected in place of this parameter with proper terminal block inputs. Refer to charts on Pages 5-29 and 5-30. Important: If an adapter that is not connected is selected as the active frequency source, the drive will fault on Hz Sel Fault (F30).
Factory Default Adapter 1 Settings Remote Pot 0-10 Volt 4-20 mA MOP Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Preset 7
[Freq Select 2]
This parameter controls which of the frequency sources is currently supplying the [Freq Command] to the drive unless [Freq Select 1] or [Preset Freq 1-7] are selected with proper terminal block inputs. Refer to charts on Pages 5-29 and 5-30. Important: If an adapter that is not connected is selected as the active frequency source, the drive will fault on Hz Sel Fault (F30).
Factory Default Remote Pot Settings Remote Pot 0-10 Volt 4-20 mA MOP Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Preset 7
5-26
Programming
[Prst/2nd Accel]
This parameter, along with the [Upper Presets] parameter, determines which frequency source and Accel/Decel parameters will be selected using the optional inputs SW1, SW2 and SW3. Refer to charts on Pages 5-29 and 5-30.
[Upper Presets]
This parameter along with the [Prst/2nd Accel] parameter determines which frequency source and Accel/Decel parameters will be selected using the optional inputs SW1, SW2 and SW3. Refer to charts on Pages 5-29 and 5-30.
[Accel Time 2]
This value determines the time it will take the drive to ramp from 0 Hz to [Maximum Frequency]. The rate is linear unless [S Curve] is Enabled. It applies to any increase in command frequency unless [Accel Time 1] is selected. Refer to charts on Pages 5-29 and 5-30.
Factory Default 5.0 Sec Minimum 0.0 Sec Maximum 3600.0 Sec
Programming
5-27
Parameter # See Table Parameter Type Read & Write Units 0.1 Hz
Parameter [Preset Freq 1] [Preset Freq 2] [Preset Freq 3] [Preset Freq 4] [Preset Freq 5] [Preset Freq 6] [Preset Freq 7]
No. 27 28 29 73 74 75 76
Programming the drive for Frequency Source and Accel/Decel Control Use Table 5.A through Table 5.C to determine which frequency source and Accel/Decel Time are suitable to your application. Switch or contact inputs at terminal TB2 are used to select functionality based on how you program parameters (26), (72), and (21).
5-28
Programming
'
y ' b
Time
[MOP Increment]
The MOP function is a digital solid-state circuit that produces the same effect as rotating a speed reference potentiometer with a small DC motor. This permits local (HIM) or remote (TB2) control of the command frequency. This parameter sets the rate of increase or decrease to the [MOP Hertz] command frequency for each input to the MOP Increment or MOP Decrement terminals of TB2. (Requires the proper [Input Mode] selection or serial communications.)
Factory Default 1.00 Hz/Sec Minimum 0.00 Hz/Sec Maximum 255 Hz/Sec
y
INC Hz (Speed) ' DEC
Time
Programming
5-29
Frequency Source
Freq Select 2 (6) Preset Freq 1 (27) Accel Time 1 (7) Preset Freq 2 (28) Preset Freq 4 (73) Preset Freq 3 (29) Preset Freq 6 (75) Preset Freq 7 (76) Preset Freq 5 (74)
Accel/Decel
Decel Time 1 (8) Accel Time 2 (30) Decel Time 2 (31)
Disabled
X X X X 0 0 0 0 X X X X
Preset
Enabled
The parameter [Freq Source] indicates the active frequency source. See p. 5-45. Not valid for [Input Mode] = 3 W/2nd Acc or [Input Mode] = Run F/R 2nd A.
Valid for [Input Mode] = 3 W/2nd Acc or [Input Mode] = Run F/R 2nd A. Indicates active function/parameter. X Indicates closed switch. 0
5-30
Programming
Frequency Source
Freq Select 2 (6) Preset Freq 1 (27) Accel Time 1 (7) Preset Freq 2 (28) Preset Freq 4 (73) Preset Freq 3 (29) Preset Freq 6 (75) Preset Freq 7 (76) Preset Freq 5 (74)
Accel/Decel
Decel Time 1 (8) Accel Time 2 (30) Decel Time 2 (31)
0 0 0 X X X X 0 0 0 0 X X X X
Disabled
2nd Accel
Enabled
The parameter [Freq Source] indicates the active frequency source. See p. 5-45. Factory default settings. Indicates active function/parameter. X Indicates closed switch. 0 Indicates open switch.
Programming
5-31
SW2 TB2-17
MOP Decrement MOP Decrement
SW1 TB2-16
MOP Increment MOP Increment
The parameter [Freq Source] indicates the active frequency source. See p. 5-45. MOP Decrement When this switch is closed, [MOP Hz] is decreased at the rate programmed in [MOP Increment]. MOP Increment When this switch is closed, [MOP Hz] is increased at the rate programmed in [MOP Increment]. Indicates active function/parameter. X Indicates closed switch. 0 Indicates open switch. (26) Indicates parameter number.
[Analog Filter]
Selects the amount of software filtering applied to the 0-10 volt analog input and potentiometer input in 25% increments. The lower the percentage, the less filtering applied allowing faster response to analog signal changes. To obtain higher noise immunity, set the filter value higher. A value of 100% represents the same amount of filtering as all previous versions of released firmware. With this setting the frequency command rises to 95% of the signal input in 0.5 seconds.
5-32
Programming This group contains the necessary parameters to activate and program advanced features of the drive.
Feature Select
ATTENTION: This parameter may only be used as outlined in NFPA 79, paragraph 6-14 (exceptions 1-3) for specialized applications. Equipment damage and/or personal injury may result if this parameter is used in an inappropriate application.
[Reset/Run Tries]
This value sets the maximum number of times the drive attempts to reset a fault and restart before the drive issues a Max Retries Fault. Not operative for faults 9, 10, 11, 24, 25, 26, 29, 30, 32, 33, 34, 35, 38, 39, 40, 41, 42, 43 and 48. Important: [Reset/Run Tries] is a cumulative count. This counter resets to zero if four (4) minutes elapses since the last fault.
Programming
5-33
[S Curve Enable]
This parameter enables a fixed shape S-Curve.
Enabled
Disabled
'
Accel Time a 1 or 2
5-34
Programming
'
'
Enabled
a Accel Time 1 or 2
'
Disabled
[Language]
This parameter selects between English and the alternate second language that can be displayed on the HIM.
Factory Default Alternate language in multilingual versions,English in English only versions. Settings English or French Italian Spanish German
Programming
5-35
[Rated Slip]
p p in an This p parameter compensates for the inherent slip induction frequency iis added to th the commanded i d ti motor. t Af dd d t d d output frequency based on torque current. The actual value added may be viewed in [Slip Comp Adder] (parameter 148). If motor shaft speed decreases significantly under heavy loads then this value should be increased. A setting of 0.0 Hz disables the function. This parameter can be set more accurately based on motor nameplate RPM at full load. Use the formula and table shown.
Parameter # 146 Parameter Type Read & Write Units 0.1 Hz Rated Slip =
Factory Default 2.0 Hz Minimum 0.0 Hz Maximum 5.0 Hz Drive Rated Amps x( ) x ( Nameplate ) )] Motor FLA Hertz Motor Sync Speed Poles 60 Hz 50 Hz 2 3600 3000 4 1800 1500 6 1200 1000 8 900 750 12 600 500 = 3.38 Hz Motor
[(
Example Drive 1 HP, 460V 2.3 Amps Rated Motor Motor Sync Speed = 1800 RPM Nameplate RPM = 1725 RPM Nameplate Hertz = 60 Hz Motor FLA = 1.7 Amps Rated Slip =
[(
1800 1725
) x ( 60 ) x ( 1.7 )]
2.3
Note: Instability may occur if [Rated Slip] is set too high with operating frequencies below 10 Hz.
5-36
Programming
[IR Comp %]
A voltage is added to the output based on torque current. An additional 31 volts (maximum) is added to 460 volt units to compensate for stator resistance. 15.5 volts is added for 230 volt units. If the drive trips on an Overload fault (F7), or has trouble accelerating to commanded speed, this value should be reduced. A setting of 0% disables this function.
Programming
5-37
This group of parameters contains the programming options for digital and analog drive outputs.
Factory Default Faulted Settings At Speed Above Freq Running Faulted Alarm Above Curr
Output closes when drive reaches [Freq Command]. Output closes when drive exceeds value set in [Above Freq Val]. Output closes when drive is running. Output closes when drive is faulted. Output closes when the drive reaches hardware current limit, software current limit, overvoltage, line loss or 4-20 mA loss. Output closes when current exceeds value set in [Above Curr Val].
[Output 2 Config]
This parameter sets the condition that actuates the open collector output at TB2, terminals 19 and 20.
Factory Default Running Settings At Speed Above Freq Running Faulted Alarm Above Curr
Output closes when drive reaches [Freq Command]. Output closes when drive exceeds value set in [Above Freq Val]. Output closes when drive is running. Output closes when drive is faulted. Output closes when the drive reaches hardware current limit, software current limit, overvoltage, line loss or 4-20 mA loss. Output closes when current exceeds value set in [Above Curr Val].
Application Note: During power up of the drive, the customer programmable Outputs 1 & 2 (TB29 & 10, TB2 19 & 20) are in an indeterminate
state for a period of time until the internal control of the drive has initialized (3 sec. max.). Any control system connected to the programmable outputs should take this into consideration. On power down, the programmable outputs may transition in a similar way.
5-38
Programming
Factory Default 0 Hz Minimum 0 Hz Maximum 400 Hz NOTE: This parameter can not be programmed while the drive is running.
Factory Default 0 % of Drive Rated Current Minimum 0 % of Drive Rated Current Maximum 150% of Drive Rated Current
The drive rated output current is based on three phase input ratings. See page 5-13 for Single Phase Input Rating instructions.
Programming
5-39
Faults
This group of parameters provides information and programmed settings on commonly viewed drive faults.
[Clear Fault]
This parameter is used to clear a fault and return the drive to ready status if the fault condition no longer exists. Important: [Clear F Fault] Also I t t [Cl lt] will ill stop t a running i drive. di Al [Clear Fault] does not clear [Fault Buffer 0] through [Fault Buffer 3].
Important:To clear a fault using parameter #51, press the SEL key once to select the bottom display line. Press the keys until Clear Fault appears on the bottom display line. Press the key. This action will attempt to clear the fault. Ready will be displayed. Press the ESC key several times to get back to the Status Display and check if the fault has been cleared. If the fault has not been cleared refer to the Troubleshooting section of this manual.
5-40
Programming
Programming
5-41
Undervolt Fault T1 T2 T3
No Output Power
Undervolt Fault T4 T5 T6
Application Notes: If line loss is set to U Volt Run and [Run On Power Up] is enabled, the drive will run as long as the bus voltage is high enough to maintain logic. To obtain longer power ride-thru, choose U Volt Run. This allows the output power to be on from time T1 to T3. To obtain a longer control ridethru, choose F03 Enable. The output power devices are turned off at time T5 but note that time T6 T5 is greater than time T3 T2. [Flt Clear Mode]
This parameter controls the method for clearing faults. Parameter # 39 Parameter Type Read & Write Units Text Factory Default Enabled Setting Enabled Disabled
Faults Cleared By Issuing a Valid Stop Command or Cycling Input Power Faults Cleared Only By Cycling Input Power
5-42
Programming This group of parameters contains values that can be helpful in explaining the operation of the drive. Drive status, direction, control and alarm conditions are included.
Parameter # 58 Parameter Type Read Only
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Run Reverse Accel 2 Decel 2 N/A N/A N/A N/A Run Reverse Accel 2 Decel 2 Not Used Not Used Not Used Not Used
Diagnostics
[Drive Command]
This parameter displays the status of the drive commands in an 8-bit binary format.
Programming
5-43
5-44
Programming
[Input Status]
This parameter displays the open (0) and closed (1) status of inputs at TB2. Refer to Figure 2.7 through Figure 2.10 for description of terminal connections.
Programming
5-45
Displays Remote Pot 0-10 Volt 420 mA MOP Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Factory Default 0.00 Hz Minimum 0.00 Hz Maximum 400.00 Hz
[Freq Command]
This parameter displays the frequency that the drive is commanded to output. This command may come from any one of the frequency sources selected by [Freq Select 1], [Freq Select 2] or [Preset Freq 1-7] as determined by inputs to SW1, SW2 and SW3 at TB2.
[Drive Direction]
This parameter displays the running direction of the drive.
[Motor Mode]
This parameter is used for internal diagnostic purposes.
5-46
Programming
[Drive Type]
This parameter displays a decimal number that identifies the drive.
[Firmware Ver]
This parameter displays the version number of the drive firmware.
[Output Pulses]
This parameter displays the number of output cycles for the PWM waveform. The count rolls over at 65535.
[Drive Temp]
This parameter displays the internal drive temperature.
Parameter # 70 Parameter Type Read Only Units 1 Degree C Parameter # 64 Parameter Type Read & Write Units Text
Factory Default None Minimum 0 Degrees C Maximum 100 Degrees C Factory Default Ready
Display After Function Complete Saves parameter Ram to EEPROM Restores parameter Ram from EEPROM Resets All Parameters to Their Factory Settings
[Set Defaults]
Setting parameter to Default Default Init Init resets all parameters to their factory values. See also page 3-11 EEPROM Mode.
Ready Settings Ready Store to EE Note: This parameter can not be programmed while Recll frm EE Default Init the drive is running.
Programming
5-47
Masks
This group of parameters contains binary masks for all control functions except the stop command. The masks control which adapters can issue control commands. Mask
Each mask contains a bit for each adapter. Individual bits can be set to 0 to lockout control by an adapter or set to 1 to permit an adapter to have control.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0 TB2 Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 N/A TB2 Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Not Used
[Logic Mask]
This parameter determines which adapters are allowed to control the drive logic commands. Setting a bit to 0 (deny control) disables all command functions except stop and frequency reference. Important: In order to remove an adapter from the drive without causing a drive communications fault, the corresponding bit for that adapter must be set to zero. Important: This parameter has no effect on the frequency value being sent from TB2 or any of the adapters.
[Direction Mask]
This parameter determines which adapters can issue forward/reverse commands. Important: Terminal Block (TB2) will have control unless masked out.
5-48
Programming
[Jog Mask]
This parameter determines which adapters can issue jog commands.
[Reference Mask]
This parameter determines which adapters can control the switching between the available freq. reference sources. Important: Terminal Block (TB2) will have control unless masked out.
[Accel Mask]
This parameter determines which adapters can switch between [Accel Time 1] and [Accel Time 2]. Important: Terminal Block (TB2) will have control unless masked out.
[Decel Mask]
This parameter determines which adapters can switch between [Decel Time 1] and [Decel Time 2]. Important: Terminal Block (TB2) will have control unless masked out.
Programming
5-49
[MOP Mask]
This parameter determines which adapters can issue MOP commands to the drive.
[Local Mask]
This parameter determines which adapters can issue a Local command in order to obtain exclusive control of the drive. For safety reasons, local control can only be granted or removed while the drive is not running and is in a safe state. If any adapter is in local control of the drive, all other adapters are locked out and prohibited from controlling any logic function except stop. Important: The only way to obtain local control of Bulletin 1305 drives is through the serial port via a PLC command. Important: This parameter has no effect on the frequency value being sent from TB2 or any of the adapters..
5-50
Programming This group of parameters contains binary status information to display which adapters are issuing control commands. Owners
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TB2 Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 N/A TB2 Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Not Used
Owners
[Stop Owner]
This parameter displays which adapters are currently issuing a valid stop command.
Settings 1 0
[Direction Owner]
This parameter displays which adapter currently has exclusive control of direction changes. When commanding the direction from an adapter, the corresponding bit is set to 1. Important: Only one adapter is allowed to control direction at any instance.
Settings 1 0
Programming
5-51
Settings 1 0
[Jog Owner]
This parameter displays which adapters are currently issuing Jog commands. Since the Jog function is momentary, multiple adapters can issue Jog commands simultaneously. This means that all adapters issuing the Jog must stop commanding the Jog before the function ceases. Important: Stop commands will terminate Jog control and Start commands will override any Jog command.
Settings 1 0
5-52
Programming
Settings 1 0
[Accel Owner]
This parameter displays which adapter currently is exclusively controlling the selection between [Accel Time 1] and [Accel Time 2].
Settings 1 0
[Decel Owner]
This parameter displays which adapter currently is exclusively controlling the selection between [Decel Time 1] and [Decel Time 2].
Settings 1 0
[Fault Owner]
This parameter displays which adapters are currently issuing a [Clear Faults] Command. Multiple adapters can issue simultaneous [Clear Faults] Commands.
Settings 1 0
Programming
5-53
[Local Owner]
This parameter displays which adapter currently has exclusive control of all drive logic functions by requesting a LOCAL command. If an adapter is the [Local Owner], all other functions (except stop) on all other adapters are locked out and non-functional. Important: Local control can only be granted when the drive is in a safe state or stopped.
Settings 1 0
5-54
Programming This group contains the parameters needed for an optional communications adapter to communicate with the drive.
Parameter # 111 - 118 Parameter Type Read & Write Parameter 111 Data In A1 112 Data In A2 113 Data In B1 114 Data In B2 115 Data In C1 116 Data In C2 117 Data In D1 118 Data In D2 Bulletin 1305 drive Controller Output Image Table (i.e. PLC, SLC, etc.) Important: addressing information that defines which controller I/O address corresponds to a [Data In] parameter is determined by the dip switch settings on the external communication module. Refer to the appropriate Bulletin 1203 Communication Module User Manual for details. Refer to Appendix B for additional information.
Important: The drive parameter that is accessed indirectly using Data In will not be stored permanently and automatically to EEPROM (due to the high potential update rate from a PLC). A manual operation is necessary for permanent storage. The HIM EEPROM command, Save Values, or using parameter (64) [Set Defaults] will perform this task. Similarly, to restore the values to the ones the drive had before Data In was configured, the HIM Recall Values Function can be used. [Data Out A1 through D2]
These parameters are used to write real time data values from the drive to a destination controller. This is accomplished by programming a parameter number into the [Data Out] parameters. The real time value of that parameter will be written to the input image table of the destination controller. Parameter # 119 - 126 Parameter Type Read & Write Parameter Bulletin 1305 drive 119 Data Out A1 120 Data Out A2 121 Data Out B1 122 Data Out B2 123 Data Out C1 124 Data Out C2 125 Data Out D1 126 Data Out D2 Controller Input Image Table (i.e. PLC, SLC, etc.) Important: addressing information that defines which controller I/O address corresponds to a [Data Out] parameter is determined by the dip switch settings on the external communication module. Refer to the appropriate Bulletin 1203 Communication Module User Manual for details. Refer to Appendix B for additional information.
Programming
5-55
Process Display
This group contains parameters that can be used to display a drive parameter in User Units.
[Process Par]
This parameter should be set to the number of the parameter whose scaled value will be displayed on Line 1 of the HIM Display Panel when in process mode.
[Process Scale]
This value sets the scaling multiplier for [Process Par]. The displayed value will be: [Process Par] actual value [Process Scale] value Displayed Value
Parameter #(s) 129-136 Parameter Type Read & Write Units ASCII Text Character
Factory Default ?
The maximum value that can be displayed is 99,999.99. If this value is exceeded a character string of asterisks (******* ) will appear on the display.
5-56
Linear List
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Output Voltage % Output Curr % Output Power Last Fault Freq Select 1 Freq Select 2 Accel Time 1 Decel Time 1 DC Boost Select Stop Select DB Enable DC Hold Time DC Hold Volts Run On Power Up Reset/Run Time Minimum Freq Base Frequency Base Voltage Maximum Freq Maximum Voltage Input Mode MOP Increment Output Power Jog Frequency Analog Out Sel Prst/2nd Accel 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Preset Freq 1 Preset Freq 2 Preset Freq 3 Accel Time 2 Decel Time 2 Skip Freq 1 Skip Freq 2 Skip Freq 3 Skip Freq Band Current Limit Overload Mode Overload Current Flt Clear Mode Line Loss Fault Motor Type MOP Hertz Motor Mode Power Mode PWM Frequency Current Angle Language Start Boost Break Frequency Break Voltage Clear Fault Compensation
53 54 55 56 57 58 59 60 61 62 64 65 66 67 69 70 71 72 73 74 75 76 77 81 82 83
DC Bus Voltage Output Current Input Status S Curve Time S Curve Enable Drive Command Drive Status Drive Alarm Drive Type Freq Source Set Defaults Freq Command Output Freq Output Pulses Drive Direction Drive Temp Firmware Ver Upper Presets Preset Freq 4 Preset Freq 5 Preset Freq 6 Preset Freq 7 Above Freq Val 420mA Loss Sel Cur Lim Trip En Run Boost
84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109
Analog Invert Reset/Run Tries Fault Buffer 0 Fault Buffer 1 Fault Buffer 2 Fault Buffer 3 Output 1 Config Output 2 Config Logic Mask Local Mask Direction Mask Start Mask Jog Mask Reference Mask Accel Mask Decel Mask Fault Mask MOP Mask Stop Owner Direction Owner Start Owner Jog Owner Reference Owner Accel Owner Decel Owner Fault Owner
110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135
MOP Owner Data in A1 Data In A2 Data In B1 Data In B2 Data In C1 Data In C2 Data In D1 Data In D2 Data Out A1 Data Out A2 Data Out B1 Data Out B2 Data Out C1 Data Out C2 Data Out D1 Data Out D2 Process Par Process Scale Process Text 1 Process Text 2 Process Text 3 Process Text 4 Process Text 5 Process Text 6 Process Text 7
136 137 141 142 143 144 146 147 148 149
Process Text 8 Local Owner Sec Curr Limit Above Curr Val Cable Length Analog Filter Rated Slip IR Comp % Slip Comp Adder Adaptive I Lim
Chapter
All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators provided to display the drives status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below. How To Clear a Fault Important: Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following: 1. Cycle power to the drive. 2. Cycle the stop signal to the drive. 3. Cycle the [Clear Fault] parameter. See page 5-39. Important:The stop signal will not clear a fault if the [Logic Mask] or [Fault Mask] bit of that adapter has been disabled or the [Fault Clear Mode] parameter is disabled.
FAULT INFORMATION
Figure 6.1 Fault Display
Drives equipped with a Human Interface Module will display a brief fault message on Line 1 of the LCD display when a fault occurs. Line 2 of the display indicates the corresponding fault number. Important: For Series A HIM software version 3.00 and Above or Series B HIM software version 1.01 and Above, faults are displayed as soon as they occur. Earlier HIM versions only display faults when the HIM is in the Status Display Mode. [Fault Buffer 0] through [Fault Buffer 3] display previous faults. Table 6.A lists all faults numerically with a cross reference to the page number where information can be found relating to that fault. Table 6.B provides an alphabetized listing of the faults with a description and possible corrective action to take.
6-2
These faults are generated in the HIM and not stored in the drive EEPROM.
Troubleshooting and Fault Information Table 6.B 1305 Fault Descriptions Name & Fault Number Diag C Lim FauIt F36 Drive HIM Drive Reset FauIt F22 EEprom Fault F32 Hz Err Fault F29 Description The drive output current has exceeded the software [Current Limit] and the [Cur Lim Trip En] parameter was enabled. Action to Take Check programming of [Curr Lim Trip En] parameter. Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current.
6-3
The checksum read from the HIMs EEPROM does not match the Repeat operation. Replace HIM. checksum calculated from the EEPROM data. Occurs on power-up. Caused by having the Start Input (or Run Check stop connection at TB2, terminal 8. Input) closed, with the Stop Input open and [Run On Power Up] = Disabled. EEPROM has invalid data or can not be programmed to valid data. Check cable connection from main control board to power board. Reset to Default Parameters and Cycle power.
This fault indicates that there is not a valid operating frequency. 1. Check [Minimum Freq] and [Maximum Freq] parameters. It can be caused by any of the following: 2. Check [Skip Freq 1], [Skip Freq 2], [Skip Freq 3] and [Skip Freq Band] parameters. 1. [Maximum Frequency] is less than [Minimum Freq]. 3 Check for broken wires, wires loose connections or transducer 2 Skip frequencies and skip bandwidth eliminate all operating 3. 2. loss at 4-20mA input, TB2. frequencies. 3. 4-20mA input signal speed reference has been lost or is out of range and [4-20mA Loss Sel] is set for Stop-Fault. An adapter that is not connected has been chosen as the active Connect proper adapter or change active frequency source. frequency source.
6-4
Table 6.B 1305 Fault Descriptions (continued) Fault Name & Number HIM Drive Fault Description Action to Take
Error 1 The checksum read from the HIMs EEPROM does not Repeat operation. Old profile corrupt. Save new profile. Repeat match the checksum calculated from the EEPROM data. operation. Error 2 The number of parameters in saved profile does not equal master. Error 3 Download was attempted to a different type drive (i.e. 1336->1305). Error 4 Saved data for parameter not correct for new drive. The last parameter programmed will be displayed on the top line. Verify that all parameters have been programmed. If not, manually program any remaining parameters. Download can only take place with the same type of drive. Capabilities of drive are different than the master drive. Press Enter to continue download. When download is complete, manually program the parameter where the error occurred. Stop drive, then perform download.
Error 5 Drive is running while attempting download. IPM Current Fault F44 IPM Overtemp Fault F45 Max Retries Fault F33
The internal power module overcurrent limit had been exceeded. Check for short circuit at the drive output or excessive load conditions at the motor, specifically cable capacitance to ground. The internal power module thermal limit has been exceeded. Check for blocked or dirty heat sink fins. Check for proper mounting and spacing (See page 2-1). Check if the ambient temperature limit has been exceeded. Check fault buffer for fault code requiring reset. Correct the cause of the fault and manually clear by cycling the stop command or cycling power.
Drive unsuccessfully attempted to reset a fault and resume running for the programmed number of [Reset/Run Tries].
Troubleshooting and Fault Information Table 6.B 1305 Fault Descriptions (continued) Fault Name & Number Motor Mode FIt F24 Motor Stall Fault F6 Neg Slope Fault F35 Fault Description Internal error. The motor is stalled. Action to Take Reset drive to factory defaults. If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed. A longer accel time or a reduced load may be required. Check drive programming. 1. [Base Voltage] parameter must be greater than 1.5 X [Start Boost]. 2. If the [DC Boost Select] parameter is set to Break Point, [Base Voltage] must be greater than [Break Voltage] and [Break Voltage] must be greater than [Start Boost].
6-5
Drive software detected a portion of the volts/Hz curve with a negative slope.
Network Error
1. Press the UP or DOWN arrow to clear the message from the HIM display. 2. Unplug the HIM from the cable or drive and re-connect. 3. Check for external noise sources. [Motor Type] is set to Sync PM and [Stop Mode] is set to DC Change one of these parameters. DC Braking cannot be used Brake. with a synchronous motor. An external pot is connected and the ground lead of the pot is Check the external potentiometer circuit at TB2, terminals 1, 2 disconnected creating a potential drive overspeed hazard. and 3 for an open circuit.
6-6
Table 6.B 1305 Fault Descriptions (continued) Fault Name & Number Fault Description Overcurrent FauIt F12 Overload Fault F7 Overcurrent is detected in overcurrent hardware trip circuit. Internal electronic overload trip.
Action to Take Check for a short circuit at the drive output or excessive load conditions at the motor. An excessive motor load exists. It must be reduced such that drive output current does not exceed the % of current set by the [Overload Current] parameter. Reduce [Start Boost] if applicable. Change [Cable Length] to Long if applicable. Reset drive to factory defaults. Check for blocked or dirty heat sink fins. Check for proper mounting and spacing (See page 2-1). Check if the ambient temperature limit has been exceeded. Monitor the AC line for high line voltage or transient conditions. Bus overvoltage can also be caused by motor regeneration. Extend the decel time or install dynamic brake option.
Overspeed Fault F25 Overtemp Fault F8 Overvolt Fault F5 Phase U Fault F38 Phase V Fault F39 Phase W Fault F40
A phase to ground fault has been detected between the drive and motor in this phase. A phase to ground fault has been detected between the drive and motor in this phase. A phase to ground fault has been detected between the drive and motor in this phase.
Check the wiring between the drive and motor. Check motor for grounded phase. Check the wiring between the drive and motor. Check motor for grounded phase. Check the wiring between the drive and motor. Check motor for grounded phase.
Troubleshooting and Fault Information Table 6.B 1305 Fault Descriptions (continued) Fault Name & Number Pin ID Error Power Loss Fault F3 Power Mode Fault F26 Power Test Fault F46 Reprogram Fault F48 Run Boost Fault F34 Serial Fault F10 Fault Description Communication Hardware problem. Action to Take 1. Unplug the HIM from the cable or drive and re-connect. 2. Replace Communication Cable.
6-7
DC bus voltage remained below 85% of nominal for longer than Monitor the incoming AC line for low voltage or line power 0.500 sec. [Line Loss Fault] parameter is programmed to F03 interruption. Enable. Internal error. Fault detected during initial start-up sequence. Occurs when drive parameters are reset to defaults. Reset drive to factory defaults. Check drive wiring. Check motor wiring. Reset drive to factory defaults. Clear fault.
An attempt has been made to set the [Run Boost] parameter to Verify that parameter has been programmed correctly. a value greater than the [Start Boost] parameter. An active local bus adapter is disconnected while it possesses control of a local bus function. Check for break in communications line.
6-8
Table 6.B 1305 Fault Descriptions (continued) Fault Name & Number Undervolt Fault F4 UV Short Fault F41 UW Short Fault F42 VW Short Fault F43 Fault Description DC Bus voltage fell below the minimum value. [Line Loss Fault] parameter is programmed to U Volt Run. Excessive current has been detected between these two drive output terminals. Excessive current has been detected between these two drive output terminals. Excessive current has been detected between these two drive output terminals. Action to Take Monitor the incoming AC line for low voltage or line power interruption. Check the motor and external wiring to the drive output terminals for a shorted condition. Check the motor and external wiring to the drive output terminals for a shorted condition. Check the motor and external wiring to the drive output terminals for a shorted condition.
Troubleshooting and Fault Information Table 6.C Troubleshooting General Problem Motor does not start (No output voltage to motor) (Stopped is displayed on the HIM). Action to Take (1) Check power circuit - Check supply voltage. - Check all fuses and disconnects. (2) Check motor - Verify that motor is connected properly. (3) Check control input signals. - Verify that Enable signal is present. (Not Enabled is displayed on the HIM) - Verify that Start signal is present. - Verify that Stop signal is present. - Verify that Run Forward and Run Reverse signals are NOT both active. (4) Check parameter mask settings - Verify that [Start Mask] is set properly. - Verify that [Logic Mask] is set properly. - Verify that [Local Mask] is set properly.
6-9
Drive Started but motor NOT rotating. (1) Check motor - Verify that motor is connected properly. (At Speed 0.00 Hz is displayed on HIM). (2) Check Frequency Source - Verify that frequency signal is present at terminal block TB2. - 4-20mA signal - 0-10V signal -Remote Potentiometer - Verify that Adapter or Preset Frequencies are set properly. (3) Check control input signals. - Verify that SW1, SW2 and SW3 are in the proper state. (Refer to Table 5.A on page 5-29) (4) Check parameter settings and charts on Pages 5-29 and 5-30. - Verify that [Freq Source] is showing the desired frequency source. - Verify that [Freq Command] is the desired value. - Verify that [Reference Mask] is set properly.
6-10
Can not change direction from Adapter. Can not Start from Adapter.
(1) Verify that [Direction Mask] is set to allow direction changes from that adapter. (2) Verify that [Logic Mask] is set to allow direction changes from that adapter. (1) (2) (3) (4) Verify that [Start Mask] is set properly to allow starting from that adapter. Verify that [Logic Mask] is set properly to allow starting from that adapter. Is drive already running? Examine [Stop Owner] to verify that a maintained Stop does not exist.
6-11
Pin ID Error is displayed on HIM. Network Error is displayed on the HIM. Can not clear fault from Adapter or Terminal Block with stop command.
6-12
Appendix A
Jog
SW1
TB2-17
SW2
TB2-18
Analog Circuitry
TB2-3 Common
Relay Circuitry
0-10V 4-20ma
A-2
Adjustable from 0 V to Input Voltage 0.00 to 400.00 Hz Programmable 250 mA maximum (all adapters combined)
In general: Motor Full Load Amps (FLA) should not exceed the drive output current rating. If the [PWM Frequency] is set above 4kHz, the output current must be derated per the chart on page 5-20. When operating the drive in an ambient temperature at or near the maximum operating temperature (50C), the following derating guidelines are recommended to guard against overheating depending on application and operating conditions. Output current value listed for 200V input voltage. At 230V input voltage, output current is 9.6A for 3 phase and 6.8A for single phase. Output current value listed for 380V input voltage. At 415V input voltage, output current is 5.3A. At 460V input voltage, output current is 4.8A. Output current value listed for 380V input voltage. At 415V input voltage, output current is 8.4A. At 460V input voltage, output current is 7.6A. For derating guidelines at ambient temperatures between 40C and 50C, consult Allen-Bradley.
A-3
A-4
AC Dynamic Braking Torque - Estimated - Actual value will depend on motor characteristics
Trip Free Operation, Co-ordinated for Drive and Motor Protection Programmable from 20% to 150% of Drive Rated Current 200%, Fixed by hardware, based on drive rating 150% for 60 seconds
A-5
See Page 5-12 for NEC and UL information. Conditions such as ambient temperature, overload, duty cycle, etc. can affect tripping time.
A-6
Serial Communications
COMMUNICATIONS USING BULLETIN 1203 COMMUNICATION MODULES
Bulletin 1305 drive parameter data can be programmed and displayed using PLCs, SLCs or other logic controllers using an optional Bulletin 1203 Communication Module. The amount of information that can be transferred between the drive and controller is determined by the DIP switch settings on the Communication Module. Table B.1 illustrates the dip switch settings for Bulletin 1203-GD1 (Remote I/O) communication modules. Dip switch settings for other communication modules will be similar. Refer to the appropriate communication module user manual for details. Important: 1305 drives with firmware revisions FRN1.01 and FRN1.02 are not compatible with Bulletin 1203 Communication Modules. If connected, an error message will be indicated. The red fault status and amber SCANportT status LEDs on the front of the module will flash simultaneously.
SCANport is a trademark of Allen-Bradley Company.
Appendix B
Table B.1 Remote I/O Data Transfer
SW3 Settings No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 Rack Space in Words 1 1 1 2 2 2 2 Reference Information See Table B.2 & Table B.3 See Page 5-54 See Page 5-54 See Page 5-54 See Page 5-54
Type of Data Transferred Block transfer of data Logic commands and Drive Status information Analog frequency reference Parameter data via Datalink A Parameter data via Datalink B Parameter data via Datalink C To transfer data via Datalink D Unused
Refer to the Bulletin 1203 Communication Module Block Transfer User Manual. To enable the PLC to provide the frequency reference, Logic Bits 12 through 15 must be set to select [Freq Select 1] or [Freq Select 2] as the frequency reference (refer to Table B.2 ). The [Freq Select 1] or [Freq Select 2] parameters must then be set to the adapter number that the communication module is connected to. See Pages 2-24 and 5-25 for additional information on determining the Adapter number and [Freq Select 1] and [Freq Select 2] selections.
B-2
Serial Communications
B-3
This information will be displayed in the controllers output image table and will be sent to the drive when the appropriate dip switch setting on the Communication Module is enabled.
15 14 13 12 11 10 9 Logic Bits 8 7 6 5 4 3 2 1 X X X X X X X X X X X X X X 0 X Status Stop Start Jog Clear Faults Direction Local MOP Increment Accel Time Decel Time Reference Select Text 1 = Stop, 0 = Not Stop 1 = Start, 0 = Not Start 1 = Jog, 0 = Not Jog 1 = Clear Faults 0 = Not Clear Faults 00 = No Command 10 = Reverse Command 01 = Forward Command 11 = Hold Direction Control 1 = Local Lockout, 0 = Not Local 1 = Increment, 0 = Not 00 = No Commd 10 = Accel Time 2 Commd 01 = Accel Time 1 Commd 11 = Hold Accel Time Ctrl 00 = No Commd Time 10 = Decel Time 2 Commd 01 = Decel Time 1 Commd 11 = Hold Time Ctrl 000 = No Command Select 001 = [Freq Select 1] (Selectable) 010 = [Freq Select 2] (Selectable) 011 = [Preset Freq 3] 100 = [Preset Freq 4] 101 = [Preset Freq 5] 110 = [Preset Freq 6] 111 = [Preset Freq 7] 1 = Decrement, 0 = Not
MOP Dec
B-4
Serial Communications
This information will be displayed in the controllers input image table when the appropriate dip switch setting on the Communication Module is enabled.
15 14 13 12 11 10 9 Logic Bits 8 7 6 5 4 3 2 1 X X X X X X X X X X X 0 X Status Enabled Running Rotating Direction Accel Decel Alarm Fault At Speed Local Text 1 = Enabled, 0 = Not Enabled 1 = Running, 0 = Not Running 1 = Forward, 0 = Reverse 1 = Accelerating, 0 = Not 1 = Decelerating, 0 = Not 1 = Alarm, 0 = No Alarm 1 = Faulted, 0 = Not Faulted 1 = At Speed, 0 = NOT at Speed 000 = TB2 Local 001 = Adapter 1 Local 010 = Adapter 2 Local 011 = Adapter 3 Local 0000 = Freq Select 1 0001 = Preset Freq 1 0010 = Preset Freq 2 0011 = Preset Freq 3 0100 = Preset Freq 4 0101 = Preset Freq 5 0110 = Preset Freq 6 0111 = Preset Freq 7 100 = Adapter 4 Local 101 = Adapter 5 Local 110 = Adapter 6 Local 111 = No Local Control 1000 = Freq Select 2 1001 = Port 1 Adapter 1 1010 = Port 2 Adapter 2 1011 = Port 3 Adapter 3 1100 = Port 4 Adapter 4 1101 = Port 5 Adapter 5 1110 = Port 6 Adapter 6 1111 = Jog Frequency
Frequency Reference
B-5
Users Setting
Mete M ering
Output Freq Freq Command MOP Hz Drive Temp Last Fault % Output Power % Output Curr
Refer to Table B.5 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions Refer to page B-2.
B-6
Serial Communications
0 40
20% of DRC
20% of DRC
0% of DRC
Maximum 3600.0 3600.0 400 100% of Drive Rated Volts 110% of Drive Rated Volts 120 400 150% of Drive Rated Current (DRC) 115% of Drive Rated Current (DRC) 150% of Drive Rated Current (DRC)
Factory Setting Three Wire Adapter 1 10.0 10.0 60 Drive Rated Volts Drive Rated Volts 0 60 Ramp 150% of DRC No Derating 115% of DRC 0% of DRC Enabled
Users Setting
Refer to Table B.6 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions Refer to page B-2.
Set S t Up Up
B-7
Users Setting
Maximum Voltage DC Boost Select Start Boost Run Boost PWM Frequency Analog Invert 420 mA Loss Sel Stop Select DC Hold Time DC HoId Volts DB Enable Motor Type Compensation
Refer to Table B.1 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions. Refer to page B-2.
B-8
Serial Communications
Refer to Table B.7 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions. Refer to page B-2.
B-9
Users Setting
Refer to Table B.1 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions. Refer to page B-2.
Fault Fa lts
B-10
Serial Communications
Refer to Table B.1 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions. Refer to page B-2.
M sks Mask
B-11
Setting
Ow wner ers
B-12
Serial Communications
Process Text 2 Process Text 3 Process Text 4 Process Text 5 Process Text 6 Process Text 7 Process Text 8
Refer to Table B.1 on pages B-13, B-14 and B-15 for the numerical equivalent of the text descriptions. Refer to page B-2.
Serial Communications Table B.1 Display Unit Equivalent to Parameter Text Descriptions
Parameter Number 5 6 62 Parameter Name Freq Select 1 Freq Select 2 Freq Source Text Remote Pot 0-10 Volt 4-20 mA MOP Adapter 1 Adapter 2 Adapter 3 Adapter 4 Adapter 5 Adapter 6 Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Preset 7 Jog Sel Display Unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Valid for parameter (62) [Freq Source] only. 10 Stop Select Parameter No. 9 Parameter Name DC Boost Select Text Fan Sel #1 Fan Sel #2 No Boost 6 volts 12 volts 18 volts 24 volts 30 volts 36 volts Display Unit 0 1 2 3 4 5 6 7 8 9 10 11 12
B-13
42 volts
48 volts Break Point Run Boost Coast DC Brake Ramp S-Curve
0 1 2 3
B-14
Serial Communications
0 1
0 1
0 1 0 1
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9
0 1
2 3 4 5
0 1 2 3
4
0 1 0 1 2
0 1
Serial Communications Table B.1 Display Unit Equivalent to Parameter Text Descriptions (continued)
Parameter No. 47 51 52 57 64 Parameter Name Language Clear Fault Compensation S-Curve E bl Enable Set Defaults Text English Alternate Language Ready Clear Fault No Comp. Comp. Disabled Enabled Ready Store to EE Recll frm EE Default Init 69 72 81 Drive Direction Upper Presets 4-20mA Loss Sel Forward Reverse Disabled Enabled Min/Alarm Stop/Fault Hold/Alarm Max/Alarm Pre1/Alarm Display Unit Parameter No. 82 84 90 91 Parameter Name Curr Lim Trip En Analog Invert Output p Config g1 Output Config 2 Text Default Run Trip @ I Lmt Disabled Enabled At Speed Above Freq Running Faulted Alarm Above Curr 143 144 Cable Length Analog Filter Short Long 0% 25% 50% 75% 100% 149 Adaptive I Lim Disabled Enabled Display Unit
B-15
0 1 0 1 0 1
0 1
0 1
0 1
0 1 2 3 0 1
0 1
0 1 2 3 4
5
0
1
0 1 2 3
4
0 1 2 3 4
0
1
B-16
Serial Communications
Drive Accessories
Table C.1 Accessories
Bulletin 1201 Descriptions Door Mount Bezel Kit Blank Cover Human Interface Module Programmer Only Human Interface Module Analog Speed Potentiometer Human Interface Module Programmer/Run Time Functions Human Interface Module Digital UpDown Speed Control Bulletin 1202 Descriptions (Male-Male) Communication Cable (Male Male) for Port 2 0.33 Meter (1.1 Feet) 1 Meter (3.3 (3 3 Feet) 3 Meter (9.8 Feet) 9 Meter (29.5 Feet) Communication Cable (Male-Female) (Male Female) for Port 1 0.33 Meter (1.1 Feet) 1 Meter (3.3 (3 3 Feet) 3 Meter (9.8 Feet) 9 Meter (29.5 Feet) Bulletin 1203 Descriptions Single Point Remote I/O Communication Module RS232/RS422/RS485/DF1/DH485 Serial Communication Module DeviceNet Communication Module 2 Port Splitter 4 Port Splitter SLC/SCANport Module Flex I/O SCANport Terminal Base Flex I/O SCANport Module Use With Human Interface Module and Communications Modules Use With Bulletin u e 1305 305 Drives es IP30 (NEMA Type 1) Cat. No. 1201-DMA 1201-HAB 1201-HAP 1201-HA1 1201-HA2 Cat. No. 1202-C03 1202 C10 1202-C10 1202-C30 1202-C90 1202-H03 1202 H10 1202-H10 1202-H30 1202-H90 Cat. No. 1203-GD1/GK1 1203-GD2/GK2 1203-GK5 1203-SG2 1203-SG4 1203-SM1 1203-FB1 1203-FM1 IP66 NEMA Type 12 (ULType 4X Indoor) Cat. No. 1201-HJP 1201-HJ2 Cat. No. IP30 NEMA Type 1/12 (Enhanced) Cat. No. 1201-HJPE 1201-HJ3E Cat. No.
Appendix C
Hand Held) (Enhanced) Cat. No. 1201-HHPE 1201-HH3E Cat. No.
Cat. No.
Cat. No.
Cat. No.
C-2
Drive Accessories
Drive Out. Ratings HP 0.5 0.75 1 2 3 0.5 0.75 1 2 3 3 5 5 kW 0.37 0.55 0.75 1.5 2.2 0.37 0.55 0.75 1.5 2.2 2.2 4.0 4.0
Input Line Reactors Open Style 1321-3R4-B 1321-3R4-A 1321-3R4-A 1321-3R8-A 1321-3R12-A 1321-3R2-B 1321-3R2-A 1321-3R2-A 1321-3R4-B 1321-3R4-B 1321-3R8-B 1321-3R8-B 1321-3R12-B NEMA Type 1 230V AC 1321-3RA4-B 1321-3RA4-A 1321-3RA4-A 1321-3RA8-A 1321-3RA12-A 460V AC 1321-3RA2-B 1321-3RA2-A 1321-3RA2-A 1321-3RA4-B 1321-3RA4-B 1321-3RA8-B 1321-3RA8-B 1321-3RA12-B
Isolation Transformer NEMA Type 1 1321-3T003-AA 1321-3T003-AA 1321-3T005-AA 1321-3T005-AA 1321-3T005-AA 1321-3T003-BB 1321-3T003-BB 1321-3T005-BB 1321-3T005-BB 1321-3T005-BB 1321-3T005-BB 1321-3T005-BB 1321-3T007-BB
Terminators NEMA Type 4 1204-TFA1 1204-TFA1 or TFB2 1204-TFA1 or TFB2 1204-TFA1 or TFB2 1204-TFA1 or TFB2 1204-TFA1
Note: Spare plastic parts are available contact factory. Input reactor only. [DB Enable] should be set to Enable when applying external dynamic brake kits. For use with Series C or B Drives only. DO NOT use with Series A Drives.
CE Conformity
EMC DIRECTIVE
This apparatus is tested to meet Council Directive 89/336 Electromagnetic Compatibility (EMC) using a technical construction file and the following standards, in whole or in part: D EN 50081-1, -2 General Emission Standard D EN 50082-1, -2 General Immunity Standard
Table D.1 EMC Directives Marked for all applicable directives Emissions Immunity EN55 011/CISPR 11 Level B EN50 082-1:1992 (IEC 801-2, IEC 801-3, IEC 801-4) EN50 082-2:1995 (EN 61000-4-2, ENV 50140/50204, EN 61000-4-4, ENV 50141, EN 61000-4-8, IEC 801-6)
Appendix D
REQUIREMENTS FOR CONFORMING INSTALLATION
The following six items are required for CE conformance: 1. CE marked product in NEMA Type 1 (IP30) configuration. 2. Filter and Metal Plate Kit catalog numbers are listed in Table
D.2 on the following page. One Filter and one Metal Plate Kit are required. The metal bonding plate MUST be inserted and bonded to the drive heatsink.
Important: The conformity of the drive and filter to any standard does not guarantee that the entire installation will conform. Many other factors can influence the total installation and only direct measurements can verify total conformity.
D-2
CE Conformity
FILTER
Table D.2 Filter and Metal Plate Kit Selection Filter 1305-RFB-5-A Metal Plate Kit 1305-MP-05-A 1305-MP-06-A 1305-MP-08-B AC Drive Type 1305-AA02 1305-AA03 1305-AA04 1305-AA08 1305-BA01 1305-BA02 1305-BA03 1305-BA04 1305-BA06 1305-AA12 1305-BA09
RFI Filter Installation Important: Refer to the instructions supplied with the filter for details. The RFI filter must be connected between the incoming AC supply line and the drive input terminal. RFI Filter Leakage Current The RFI filter may cause ground leakage currents. Therefore a solid ground connection must be provided.
1305-RFB-8-B
1305-RFB-12-C
1305-MP-12-C
ATTENTION: To guard against possible equipment damage, RFI filters can only be used with AC supplies that are nominally balanced with respect to ground. In some installations, three-phase supplies are occasionally connected in a 3-wire configuration with one phase grounded (Grounded Delta). The filter must not be used in Grounded Delta supplies, nor should they be used in single-phase input applications.
CE Conformity
D-3
ELECTRICAL CONFIGURATION
Figure D.1 Electrical Configuration
Conduit/4-Wire Cable R(L1) Shield* U RFI Filter S(L2) V T(L3) GRD Frame Ground Rod W GRD Frame GRD = Earth Ground GRD Motor
GROUNDING
RFI Filter Grounding Important: Shield must be terminated in cable clamp to frame. Ground wire must be connected to GRD terminal.
Important: For use with a 1305 drive with metal conduit entry panel (frame). Using an RFI filter may result in relatively high ground leakage currents. Therefore, the filter must be permanently installed and solidly grounded to the supply neutral. Grounding must not rely on flexible cables and should not include any form of plug or socket that would permit inadvertent disconnection. The integrity of this connection should be periodically checked. Refer to the instruction manual for RFI filters for CE compliance and for proper installation instructions.
D-4
MECHANICAL CONFIGURATION
Figure D.2 Mechanical Configuration
Three-Phase Input
Control I/O
Additional Control
Filter Input
Motor Output
Grounding Bracket
JO
Frames B and C
(1305-AA08A, AA12A, BA01A, BA02A, BA03A, BA04A, BA06A, BA09A)
Control I/O
Optional Brake
Filter Input
Motor Output
drive to motor) wiring must be in conduit or have shielding/armor with equivalent attenuation. Shielding/armor must be bonded to the metal conduit panel. See requirements 5 and 6 on page D-1 for details.
Index
A
Accel/Decel Control, 2-18, 5-9, 5-26, 5-29, 5-30 Accessories, C-1, D-2 Adapters, 2-23 Ambient Temperature, A-3 Analog Input 0-10V, A-3 4-20mA, 5-21, A-3 Analog Invert, 5-21 Analog Output, 5-38, A-4 Auto Restart, 5-32 Control Panel Keys Change Direction, 3-3 Increment/Decrement, 3-3 Jog, 3-2 Start, 3-2 Stop, 3-2 Control Status Mode, 3-5, 3-15 Conventions Used in Manual, 1-3 Current Limiting, 5-12, 5-13, 5-39 Current Rating, 1-5 Custom Volts/Hertz Patterns, 5-16, 5-17, 5-18 Distances between Devices, 2-1, 2-13, 2-16, 2-23, 2-24 Drive Temperature, 5-7, 5-46 Overload Fault, 6-6 Overspeed Fault, 6-6 Overtemp Fault, 6-6 Overvolt Fault, 6-6 Phase U Fault, 6-6 Phase V Fault, 6-6 Phase W Fault, 6-6 Power Loss Fault, 6-7 Power Mode Fault, 6-7 Reprogram Fault, 6-7 Run Boost Fault, 6-7 Serial Fault, 6-7 Undervolt Fault, 6-8 UV Short Fault, 6-8 UW Short Fault, 6-8 VW Short Fault, 6-8 Firmware Compatibility, 1-4 Frequency Select, 5-25, 5-29, 5-30 Fusing, AC Input, 2-6
E
EEProm Mode, 3-5, 3-11 ESD, Electrostatic Discharge, 1-1
F
Fan/Pump Volts/Hz Patterns, 5-18 Fault Buffer History, 5-39 Faults Diag C Lim Fault, 6-3, 6-4 Drive Reset Fault, 6-3 EEprom Fault, 6-3 Hertz Err Fault, 6-3 Hertz Set Fault, 6-3 IPM Current Fault, 6-4 IPM Overtemp Fault, 6-4 Max Retries Fault, 6-4 Motor Mode Fault, 6-5 Motor Stall Fault, 6-5 Neg Slope Fault, 6-5 Op Error Fault, 6-5 Open Pot Fault, 6-5 Overcurrent Fault, 6-6
B
Block Diagram, A-1
D
DC Brake to Stop, 5-11, 5-23 DC Charge Indicator, 1-2 DC Hold Volts, 5-23 Diagnostics Group, 5-42 Dimensions, 2-2 Display Mode, 3-5, 3-7 Display Panel Keys Enter, 3-2 Escape, 3-2 Increment/Decrement, 3-2 Select, 3-2
C
Carrier Frequency, 5-20, A-4 Catalog Number Description, 1-5 Choose Mode, 3-5, 3-6 Clearing Faults, 5-39, 5-41, 6-1 Control Panel Analog Speed Potentiometer, 3-3 Direction Indicators (LEDs), 3-3 Speed Indicator, 3-3
G
Group Level, 3-6
H
HIM Control Panel, 3-1
I-2
Index
Display Panel, 3-1 Installation, 3-4 Key Descriptions, 3-2 Removal, 3-4 HIM Modes Control Status, 3-5, 3-15 Display, 3-5, 3-7 EEProm, 3-5, 3-11 Password, 3-5, 3-17 Process, 3-5, 3-10 Program, 3-5, 3-7 Search, 3-5, 3-14 Human Interface Module See also HIM Key Descriptions, 3-2 Removal, 3-4 Human Interface Module (HIM), Description, 3-1
L
Language, 1-5, 5-34 LEDs Direction Indicators, 3-3 Speed Indicator, 3-3 Levels Group, 3-6 Mode, 3-6 Operator, 3-6 Parameter, 3-6 Line Reactor, 2-6 Low Line Operation, 5-40, 5-41
O
Operator Level, 3-6 Output Contacts, 5-37, 5-38, A-5 Output Disconnection, 2-6 Output Ratings, 1-5, A-2 Overload Protection, 5-12
P
Parameter Level, 3-6 Parameters % Output Current, 5-7 % Output Power, 5-7 4-20mA Loss Sel, 5-21 Above Curr Val, 5-38 Above Freq Val, 5-38 Accel Mask, 5-48 Accel Owner, 5-52 Accel Time 1, 5-9 Accel Time 2, 5-26 Adapter I/O, 5-54 Adaptive I Lim, 5-14 Advanced Setup Group, 5-15 Analog Filter, 5-31 Analog Invert, 5-21 Analog Out Sel, 5-38 Base Frequency, 5-10, 5-15
M
Min/Max Frequencies, 5-11 Mode Level, 3-6 Modes See also HIM Modes Choose, 3-5, 3-6 MOP Function, 2-18, 5-6, 5-28 Mounting, 2-1
I
Input Mode Selection, 2-17 Input Power Conditioning, 2-6 Isolation Transformer, 2-6
N J
Jog, 5-26, 5-48 Nameplate Location, 1-4
Base Voltage, 5-10, 5-16 Break Frequency, 5-16 Break Voltage, 5-17 Cable Length, 5-35 Clear Fault, 5-39 Compensation, 5-24 Current Lim Trip En, 5-40 Current Limit, 5-11 Data In A1, 5-54 Data Out A1, 5-54 DB Enable, 5-23 DC Boost Select, 5-18 DC Bus Voltage, 5-5 DC Hold Time, 5-22 DC Hold Volts, 5-23 Decel Mask, 5-48 Decel Owner, 5-52 Decel Time 1, 5-9 Decel Time 2, 5-27 Diagnostics Group, 5-42 Direction Mask, 5-47 Direction Owner, 5-50 Drive Alarm, 5-44 Drive Command, 5-42 Drive Direction, 5-45 Drive Status, 5-43 Drive Temp, 5-7, 5-46
Index Drive Type, 5-46 Fault Buffer 0-3, 5-39 Fault Clear Mode, 5-41 Fault Mask, 5-49 Fault Owner, 5-52 Faults Group, 5-39 Feature Select, 5-32 Firmware Ver, 5-46 Freq Command, 5-6, 5-45 Freq Select 1, 5-8, 5-25 Freq Select 2, 5-25 Freq Selection, 5-29 Freq Source, 5-45 Frequency Set Group, 5-25 Input Mode, 5-8 Input Status, 5-44 IR Comp %, 5-36 Jog Frequency, 5-26 Jog Mask, 5-48 Jog Owner, 5-51 Language, 5-34 Last Fault, 5-7 Line Loss Fault, 5-40 Local Mask, 5-49 Local Owner, 5-53 Logic Masks, 5-47 Masks Group, 5-47 Maximum Frequency, 5-15 Maximum Voltage, 5-10, 5-17 Minimum Frequency, 5-10, 5-15 MOP Hertz, 5-6 MOP Increment, 5-28 MOP Mask, 5-49 MOP Owner, 5-53 Motor Mode, 5-45 Motor Type, 5-23 Output 1 Config, 5-37 Output 2 Config, 5-37 Output Configuration Group, 5-37 Output Current, 5-5 Output Frequency, 5-6 Output Power, 5-5 Output Pulses, 5-46 Output Voltage, 5-5 Overload Current, 5-12 Overload Mode, 5-12 Owners, 5-50 Power Mode, 5-46 Preset Freq 1-7, 5-27 Process 1 Par, 5-55 Process 1 Scale, 5-55 Process Display Group, 5-55, 5-56 Process Txt 1-8, 5-55 Prst/2nd Accel, 5-26 PWM Frequency, 5-20 Rated Slip, 5-35 Reference Mask, 5-48 Reference Owner, 5-52 Reset/Run Time, 5-33 Reset/Run Tries, 5-32 Run Boost, 5-19 Run On Power Up, 5-32 S Curve Enable, 5-33 S Curve Time, 5-34 Sec Current Limit, 5-13 Set Defaults, 5-46 Setup Group, 5-8 Skip Frequency Band, 5-28 Skip Frequency Group 1-3, 5-27 Slip Comp Adder, 5-36 Start Boost, 5-19 Start Mask, 5-48 Start Owner, 5-51 Stop Owner, 5-50 Stop Select, 5-11, 5-22 Upper Presets, 5-26 Password Mode, 3-5, 3-17 Potentiometer Wiring, 2-21 Power Dissipation, A-2 Preset Frequencies, 5-26, 5-27, 5-29, 5-30 Process Display, 5-55, 5-56 Process Mode, 3-5, 3-10 Program Mode, 3-5, 3-7 Programming Function Index, 5-1 Using a HIM, 5-1 Programming Steps, 5-2, 5-4
I-3
R
Reverse, 2-18
S
S-Curve, 5-33, 5-34 Search Mode, 3-5, 3-14 Set Defaults, 5-46 Skip Frequencies, 5-27 Specifications Control, A-3 Environment, A-3 Input/Output Ratings, A-2 Protection, A-5 Start-Up, 4-1 Procedure, 4-1 Status Display, 3-5 Stopping, 5-11, 5-22
I-4
Index
Storage Temperature, A-3 Switch Settings Accel/Decel Selection, 5-30 Frequency Selection, 5-29
T
Three Wire (3w) Control, 2-18 Troubleshooting, 6-1 Two Wire Control, 2-17
V
Vibration, A-3 Voltage Boost, 5-18, 5-19 Voltage Rating, 1-5
W
Wiring, Control and Signal, 2-17, 2-18
Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6 34752 erenky, stanbul, Tel: +90 (216) 5698400
PN-208991
Copyright 2013 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.