Woodwork: Cambridge International Examinations General Certificate of Education Ordinary Level
Woodwork: Cambridge International Examinations General Certificate of Education Ordinary Level
Candidate Number
Name
6030/01
WOODWORK
Paper 1 Theory, Drawing and Design
October/November 2003
2 hours 45 minutes
Additional Materials:
Section
IB
3
4
5
Section II
TOTAL
This document consists of 9 printed pages and 3 blank pages.
MML 2940 3/02 S36487/2
CIE 2003
UNIVERSITY of CAMBRIDGE
Local Examinations Syndicate
[Turn over
For
Examiner's
Use
2
Section I Part A
Answer all questions from this part in the spaces provided on the question paper.
You are advised to spend no longer than 35 minutes on this part.
1
(i) ..........................................................
(ii) ...........................................................
..........................................................
...........................................................
(iii) ..........................................................
(iv) ...........................................................
..........................................................
...........................................................
[8]
Fig. 1
6030/01/O/N/03
For
Examiner's
Use
3
(c) Name the two datum surfaces shown in Fig. 2.
Fig. 2
(i) Datum surface X ......................................................................................................
Datum surface Y ......................................................................................................
(ii) Explain briefly what each datum surface is used for:
Use of Datum surface X ...........................................................................................
..................................................................................................................................
Use of Datum surface Y ...........................................................................................
..................................................................................................................................
[4]
(d) Name one softwood and one hardwood and briefly describe the characteristics of
each.
Softwood ..........................................................................................................................
Characteristics .................................................................................................................
..........................................................................................................................................
Hardwood ........................................................................................................................
Characteristics .................................................................................................................
.................................................................................................................................... [6]
6030/01/O/N/03
[Turn over
4
(e) Name a suitable adhesive for use on indoor furniture and one which has waterproof
qualities for use outdoors.
Indoor adhesive ...............................................................................................................
Outdoor adhesive ...................................................................................................... [2]
(f)
(i)
Fig. 3 shows three woodworking tools. The name of each tool is given. Name the
specific use of each tool.
Marking Gauge
Fig. 3
Use of Tool (i) ..................................................................................................................
Use of Tool (ii) .................................................................................................................
Use of Tool (iii) .......................................................................................................... [3]
6030/01/O/N/03
For
Examiner's
Use
6030/01/O/N/03
[Turn over
For
Examiner's
Use
6
Section I Part B
Answer any two questions from this part on the separate answer paper provided.
You are advised to spend no longer than 35 minutes on this part.
[1]
6030/01/O/N/03
For
Examiner's
Use
7
3
(a) Fig. 4 shows a fixing used to join together two pieces of wood.
Fig. 4
Name the fixing and describe the processes involved in preparing the wood to receive
the fixing.
[6]
(b) Fig. 5 shows a fitting.
Fig. 5
(i) Name the fitting and give a specific situation where it would be used.
[2]
[4]
(a) Sketch a cross section through the trunk of a tree and label six important features. [6]
(b) Describe briefly how each of your labelled features helps in the growth of the tree.
[6]
When designing projects to be made in the workshop there are several important stages to
work through to reach the final solution.
Name and briefly describe the main stages of designing. You should use a project you have
made yourself to help in your description.
[12]
6030/01/O/N/03
[Turn over
For
Examiner's
Use
8
Section II Drawing and Design
Answer all questions on the previously prepared drawing paper.
Use only one side of the drawing paper.
You will be required to draw part of this section to a scale of 1 : 5.
You are advised to spend 1 hour 35 minutes on this section.
On your drawing paper use the space to the right of the vertical line to answer Part C of this
section and the space to the left to answer Part D.
The drawing on page 9, Fig. 6, shows details of a telephone seat/unit. The unit has a foam
padded seat and a carcase which is designed to house a drawer and a telephone on the top.
The legs are made from solid timber, 45 square and all underframe members are also solid
timber 50 x 20 thick. The carcase is made from manufactured board 20 thick. The sizes of the
drawer parts are left to your discretion.
Part C.
full size:
Sketch freehand and approximately 1
2
(i) an exploded view of the joint you would use to join one of the corners of the
underframe at A;
[8]
(ii) a design for a handle for the drawer front; (not shown)
[5]
[3]
Part D.
(a) Draw in first or third angle projection, using a scale of 1 : 5 (hidden detail is not
required):
(i) a Front View in the direction of arrow Y;
[10]
(ii) a Sectional End View on the line XX, to include details of the drawer;
[11]
(iii) a Plan.
[2]
[3]
(c) In the Title Box include the following details in suitable lettering:
(i) a Title;
(ii) your Name;
(iii) your Examination Number;
(iv) the Projection you have used.
[3]
[3]
[2]
6030/01/O/N/03
For
Examiner's
Use
50
X
B
420
200
400
150
900
450
Fig. 6
6030/01/O/N/03
10
BLANK PAGE
6030/01/O/N/03
11
BLANK PAGE
6030/01/O/N/03
12
BLANK PAGE
6030/01/O/N/03