Professional Documents
Culture Documents
Divac Instruction Manual ENG
Divac Instruction Manual ENG
ua
http://www.sea.com.ua 02094, ., . , 13-, . 2
./ : (044) 291-00-20
Instruction Manual
MT82108B
Installation
Setting into service
Operation
Maintenance
http://www.sea.com.ua
1
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
Contents
1. Safety practices ......................................................................................................................................... 2
2. General ...................................................................................................................................................... 3
2.1 Introduction ........................................................................................................................................ 3
2.2 Standards ............................................................................................................................................ 3
3. Technical data ........................................................................................................................................... 3
3.1 Designation ......................................................................................................................................... 3
3.2 Electrical ratings and dimensions ....................................................................................................... 4
3.4 Connecting terminals ......................................................................................................................... 6
3.5 Standard equipment and options ....................................................................................................... 7
3.6 Switching times and power consumption .......................................................................................... 7
3.7 Operating conditions .......................................................................................................................... 8
4. Description and operation ........................................................................................................................ 8
4.1 Closing and opening operations : ...................................................................................................... 8
4.2 Closing springs (re)charge ................................................................................................................. 9
4.3 Front cover indicators ....................................................................................................................... 10
4.4 Structure of the poles ....................................................................................................................... 11
4.5 Operating mechanism structure ....................................................................................................... 11
4.5.1 Operating mechanism positions ............................................................................................... 12
4.6 Operation ......................................................................................................................................... 13
4.6.1 Charging of closing springs ........................................................................................................ 13
4.6.2 Closing ........................................................................................................................................ 13
4.6.3 Opening ...................................................................................................................................... 13
4.6.4 Trip-free feature......................................................................................................................... 13
4.6.5 Automatic reclosing sequence .................................................................................................. 14
4.7 Safety disposals ................................................................................................................................. 14
4.7.1 Mechanical safety ..................................................................................................................... 14
4.7.2 Electromechanical safety ......................................................................................................... 14
4.7.3 Auxiliary voltage connections ................................................................................................... 14
4.7.4 Normacel panel withdrawable versions .................................................................................... 14
5. Receipt , Transport and Storage ............................................................................................................. 15
5.1 Receipt ............................................................................................................................................. 15
5.2 Transport ........................................................................................................................................... 15
5.3 Storage .............................................................................................................................................. 15
6. Installation .............................................................................................................................................. 16
6.1. Preparatory activities ....................................................................................................................... 16
6.2. Installation process ( fixed versions ) ............................................................................................. 16
6.3. Commissioning - Preparatory checking ........................................................................................... 17
7. Inspection and Maintenance ................................................................................................................. 18
7.1 General .............................................................................................................................................. 18
7.2 Electrical working life ....................................................................................................................... 18
7.3 Periodic inspection ........................................................................................................................... 19
7.4 Lubrication ....................................................................................................................................... 20
7.5 Replacement parts ........................................................................................................................... 20
http://www.sea.com.ua
2
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
1. Safety practices
The equipment described in this manual could be remote controlled and contains high-voltage
parts and high-speed operating mechanisms.
Disregarding the following safety instructions may result in severe physical and property
damages.
Carefully read this manual before attempting any installation, operation or maintenance action.
The circuit-breakers described in this manual have been designed and tested to operate within
their rated values. Operation outside these ratings may result in severe physical and property
damages.
Satisfactory performance and useful life of these breakers depend on their correct installation,
and maintenance. Ensure that these procedures are carried out only by qualified personnel who
are familiar with the installation and maintenance of medium voltage circuits and the contents of
this manual.
Do not work on a breaker with closing springs charged. The closing springs should be discharged
and the breaker should be switched off (see Tab.I-A)
For Normacel panels Withdrawable versions:
Always leave the circuit-breaker either on Service or Test position and never in an
intermediate position in the cubicle.
Do not use a circuit-breaker by itself as the sole means of isolating a high voltage circuit.
Place the breaker into Test position.
Always remove the breaker from the panels before performing any maintenance .
Divac circuit-breakers are equipped with safety interlocks providing a simple and safe operation.
Do not defeat them.
This manual should be kept accessible to all persons concerned with installation, operation and
maintenance of these equipment.
http://www.sea.com.ua
3
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
6 1 B
2. General
2.1 Introduction
The Divac type vacuum circuit-breakers are indoor equipment suitable for normal operating conditions as
individual units for fixed installation or as Withdrawable units for air- insulated switchboards .
Due to their vacuum switching principle and simple and robust construction, Divac type circuit-breakers
have high reliability and long life expectancy. The Divac range uses a stored energy spring
operating mechanism. The basic version is fitted with a manual spring charging device or with an optional
charging motor, making the breaker suitable for auto-reclosing and also for multishot auto-reclosing fast cycles.
2.2 Standards
Divac circuit-breakers were specially designed to comply with IEC 56 and IEC 694 standards.
fig. 1 - Divac circuit-breakers (fixed installation version)
3. Technical data
3.1 Designation
Divac circuit-breakers range is designated by the
common name Divac followed by three
specification characters.
Example:
rated current
breaking current
rated voltage
http://www.sea.com.ua
4
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
3.2 Electrical ratings and dimensions
Rated
voltage
Rated insulation level
Rated
current
Short-
circuit
breaking
current
Breaker
designation
Height
(A)
Depth
(P)
Width
(L)
Distance
between
poles
(EP)
Lighting
pulse
Power
frequency
( 1 min.)
kV kV kV A kA
mm mm mm mm
12
75
28
630
16
Divac 41 B
662
456
550
200
1250
Divac 41 D
630
25
Divac 42 B
1250
Divac 42 D
1600
Divac 42 E
2000
Divac 42 F
1250
31,5
Divac 43 D
728
456
700
250 1600
Divac 43 E
2000
Divac 43 F
17,5
95
38
630
16
Divac 51 B
662
456
650
250
1250
Divac 51 D
630
25
Divac 52 B
1250
Divac 52 D
1600
Divac 52 E
2000
Divac 52 F
1250
31,5
Divac 53 D
728
456
700
250 1600
Divac 53 E
2000
Divac 53 F
24
125
50
630
16
Divac 61 B
662
456
650
250
1250
Divac 61 D
630
25
Divac 62 B
1250
Divac 62 D
1600
Divac 62 E
2000
Divac 62 F
1250
31,5
Divac 63 D
728
456
700
250 1600
Divac 63 E
2000
Divac 63 F
Making current (kA peak)
2,5 times the breaking current for all the range
Short withstand current
equal to the breaking current held for 1 or 3 seconds
Operating cycles
O - 3 min - CO - 3 min - CO
O - 0,3 s - CO - 15 s - CO - 15s - CO
http://www.sea.com.ua
5
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
fig. 2 - Divac fixed installation versions 630..2000 A, 16...25 kA, up to 24 kV.
A
fig. 3 - Divac fixed installation versions 1250...2000 A, 31,5 kA, up to 24 kV
http://www.sea.com.ua
6
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
3.3 Fixation (top views)
EP
EP
EP EP
entradade
circuitos
auxiliares
entradade
circuitos
auxiliares
fig. 4-1: Divac fixed inst. version 630..2000 A, fig. 4-2: Divac fixed installation version 630..2000 A,
16...25 kA, up to 17,5 kV. 16...25 kA, 24 kV.
M10 x 20
ISO - 4017
entrada de
circuitos
auxiliares
fig. 4-3: Divac fixed installation version 630..2000 A, fig. 4-4: fixation detail
31,5 kA, up to 24 kV.
3.4 Connecting terminals
M16
M16
M12
16,1 mm 16,1 mm
mx. 36 mm
fig.5-1 : up to 630 A - 16 kA fig. 5-2 : up to 1250 A - 25 kA fig.5-3 : up to 2000 A - 31.5 kA
http://www.sea.com.ua
7
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
3.5 Standard equipment and options
Divac circuit-breakers with manual operating mechanism
Opening and closing
1
mechanical push-buttons
Opening solenoid
Mechanical switch position indicator
Mechanical closing springs charging condition indicator
Auxiliary switches for shunt release and switch position signalling
Divac circuit-breakers with recharging motor (in addition to manual recharging mechanism)
Closing springs electrical recharging motor with protection fuses
Closing solenoid
Anti-pumping relay
Auxiliary switches for recharging motor control
Other options available
Undervoltage tripping solenoid
Additional opening solenoid
Magnetic striker release device, working without any auxiliary energy source
Mechanical switching operation counter
Auxiliary switches for closing springs status indication
Additional breaker position auxiliary switches
Connection terminals
Standard colours RAL 7032 (frame ) and RAL 7026 (front cover )
3.6 Switching times and power consumption
Divac circuit-breakers switching times (typical values )
Opening time
<50 ms
Arcing time
<20 ms
Breaking time
<70 ms
Making time
<50 ms
Closing springs charging time
<15 s
Equipment power consumption VA/W Voltage range
Charging motor
95
85-110 % Un
Closing solenoid
170
85-110 % Un
Opening solenoid
65
70-110 % Un
Undervoltage tripping solenoid:
- switching
- permanent
100
26
35 % - 70% Un
http://www.sea.com.ua
8
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
3.7 Operating conditions
Divac type vacuum circuit-breakers are indoor equipment suitable for fixed installations or Withdrawable
units for air- insulated switchboards. The indoor installation place should not have excessive moisture, dust
or corrosive fumes and sufficient heat and air circulation should be provided to prevent condensation.
Satisfactory performance of these breakers is contingent upon proper application in accordance with IEC
694 standard:
Ambient temperature range
-5 to +40 C
Maximum 24-hour average temperature
+35 C
Maximum installation altitude above sea level
1000 m
Maximum average relative humidity measured
- during 24 hours
- during a month
95%
90%
For any other operating conditions, please consult the manufacturer.
4. Description and operation
4.1 Closing and opening operations :
manual operation, using front cover mechanical push-buttons - see fig. 6:
- Closing : press the green push-button .
- Opening : press the red push-button .
electrical operation, using opening solenoid and optional closing solenoid
3
1) Mechanical closing push-button
2) Mechanical opening push-button
3) Withdrawable manual charging
lever
2
4) Switch position mechanical
indicator
5) Closing springs charging condition
6
mechanical indicator
6) Optional closing push-button key
1 interlock
7) Optional mechanical switching
operation counter
4 5 7
fig. 6 -front cover
1
On request, closing push-button can be interlocked with a key.
http://www.sea.com.ua
9
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
4.2 Closing springs (re)charge
Divac circuit-breakers are fitted with a standard closing springs manual (re)charge mechanism. Manual
charging operation is made applying a pumping action with the charging lever, as in fig. 7. After about
ten pumping movements, the (re)charging will be completed and signalised by the charging condition
indicator and lever action stops to charge closing springs.
fig. 7- manual (re)charge
In order to perform an automatic reclosing sequence, closing springs must be previously charged. In
manual versions, a hand -made (re)charge operation is necessary.
After each closing operation, automatic closing springs recharge is made in versions fitted with a
recharging motor, making these versions specially suitable for auto-reclosing sequences.
If power failure occurs during automatic recharge, manual recharge could be performed to complete
the operation .
The completion of each (re)charge operation is signalised by the charging condition indicator
http://www.sea.com.ua
10
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
4.3 Front cover indicators
The possible operating mechanism positions and circuit-breaker switch positions, as well as front cover
indicators meaning, are presented in Table I:
Position
operating mechanism switch
indicator
closing springs charging
indicator
electrical position
A
Breaker Open
Closing springs
discharged
B
Breaker Open
Closing springs
charged
C
Breaker Closed
Closing springs
discharged
D
Breaker Closed
Closing springs
charged
Table I
Whenever fitted, and after each cycle completion, mechanical switch counter increases by one the
prior reading.
http://www.sea.com.ua
11
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
4.4 Structure of the poles
1
Each pole is formed by an epoxy resin insulating
column-form envelope (1), fixed to the breaker base
frame with screws (2).The circuit-breaker live
parts, including the vacuum interrupters (3), are
4
housed inside the envelope, eliminating the
6
possibility of phase to phase and phase to ground
arcing faults.
The main circuit is formed by the upper (4) and
lower (5) terminals, the vacuum interrupter and rigid 3
(6) and flexible connectors (7).
The vacuum interrupters make use of the
7
excellent dielectric properties of high vacuum,
being able to ensure high insulation levels for very
short contact distances. In order reduce to a
negligible value the contact erosion, vacuum 5
interrupters fitted in Divac circuit breakers
8
produces an axial magnetic field between the
contact surfaces, causing the rotation and diffusion
9
of electrical arcs.
10
The opening spring (8) and contact pressure
spring (9) are mounted under the lower terminal .
The insulating rod (10) transmit to the vacuum
interrupters the operating mechanism switching
motion.
2
4.5 Operating mechanism structure
The Divac range uses a stored energy spring
operating mechanism. The opening and closing
operations are made applying the springs stored
energy to the breaker main shaft, connected to the
vacuum interrupters moveable contacts.
Depending on the version, after each closing
operation, closing springs (1) charge can be made
either manually, using the charging lever (2), or
automatically by an optional charging motor (3).
The opening (4) and closing (5) shunt solenoids
allow the electrical remote breaker operation, while
the front panel push-buttons always provide a direct
mechanical operation. The mechanical switch
position indicator (6) and the charging condition
indicator (7) provide information about the circuit
breaker condition,
fig. 8
3
2
1
4
7
6
5
fig.9
http://www.sea.com.ua
12
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
4.5.1 Operating mechanism positions
According Tab. I, the operating mechanism has four possible positions:
closing
spring
1
2
3
4
5
6
7
8
A) Breaker open B) Breaker open ,
closing springs discharged closing springs charged
C
B
A
D
C) Breaker closed, D) Breaker closed,
closing springs discharged closing springs charged
http://www.sea.com.ua
13
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
fig.
4.6 Operation
4.6.1 Charging of closing springs
In figure 10-A) the breaker is presented in the opened position with closing springs discharged.. In this
situation, the operation of the closing or opening push-buttons does not make any change in the operating
mechanism position. To make a closing operation, closing springs must be previously charged.
After a closing operation, the (re-)charging sequence will be automatic performed in versions fitted
with a charging motor. In the manual type versions, the required charging by hand is made applying a
pumping action with the charging lever, as in fig. 7. After about ten pumping movements, the (re-)
charging will be completed and signalised by the charging condition indicator.
In either versions during the (re-)charge operation, the closing springs charging mechanism transmits
the (re-)charging movement to the main cam (3) by a lever with an unidirectional roller-bearing that
prevents the rotation of the main cam in a direction opposite to the (re-)charge one (B) when the closing
springs are being charged. When main cam reach its final position, the charging condition indicator
provide the charged closing springs information, while a micro-switch cut off the charging motor
operation.
Closing springs charge condition is maintained by the roller (6) and cam (8), while opening latch is
recharged.
An immediate closing operation is possible, as the operating mechanism has now closing springs
charged (fig.10-B)
4.6.2 Closing
The closing push-button or the closing solenoid operation will cause closing latch (7) rotation in (A)
direction, freeing cam (8) and the closing springs stored energy, that will be applied as a torque in main
cam (3).
As a result, this will rotate in (B) direction, making through connection (5) main shaft rotate in (D)
direction, leading the breaker to a closed position and charging the opening latch (see fig.10-C).
4.6.3 Opening
The opening push-button or the opening solenoid operation will cause opening latch (2) rotation in (C)
direction, freeing cam (4) together with connection (5). The opening and contact pressure springs
stored energy will cause the main shaft rotation in an opposite to (D) direction, making the breaker open.
4.6.4 Trip-free feature
The Divac operating mechanism will always make an opening command prior to a closing one (trip-
free feature). If during the closing process an opening command takes place, the opening and contact
pressure stored energy free by opening latch (2) will take the breaker to an opened position.
http://www.sea.com.ua
14
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
4.6.5 Automatic reclosing sequence
In order to perform an automatic reclosing sequence, closing springs must be previously charged.
After each closing operation, automatic closing springs recharge is made in versions fitted with a
recharging motor , while manual versions need a hand-made recharge operation.
After each opening operation, charged closing springs condition is kept in order to allow an immediate
reclosing.
4.7 Safety disposals
4.7.1 Mechanical safety
Opening commands have always priority over closing ones (trip-free feature): if an opening command
is being executed, any attempt to make the breaker close will lead to closing springs discharge without
moving vacuum interrupter contacts.
4.7.2 Electromechanical safety
Depending on circuit breaker switch position, validation of opening or closing solenoid commands
is made by the rotating switches connected to main shaft, thus preventing closing solenoid operation
if the breaker is already closed and opening solenoid operation if breaker is already opened.
4.7.3 Auxiliary voltage connections
Auxiliary voltage connectors are provided in order to allow external commands. In Normacel panel
Withdrawable versions, special plug-type connectors are used .
4.7.4 Normacel panel withdrawable versions
Trying to insert or withdraw a closed circuit-breaker placed in a Normacel panel will cause the
breaker immediate opening, thus avoiding accidental interruptions or connections of the main
circuit (see Normacel Instructions Manual).
http://www.sea.com.ua
15
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
5. Receipt , Transport and Storage
5.1 Receipt
The Divac circuit-breakers are mechanically and electrically inspected before despatch, in the opened
position with discharged closing springs ( see Tab. I- A) . They are supplied individually , sealed in
plastic film and wood pallets, providing good transport and storage conditions.
During goods receipts the pallet must bee untouched
Nameplate
Check in the nameplate the compliance between
the order and the received material .
5.2 Transport
The circuit-breaker should not be unpacked before installation, in order to profit from the mechanical
protection of the package
Use always the wooden pallet during handling . Lifting tackle must never catch on the
breaker poles or the operating mechanism.
The Divac circuit-breakers are supplied with lifting tools in the points marked with the symbol
In fixed installation versions, after unpacking, move the circuit-breaker to the installation place using the
wheels .
5.3 Storage
If Divac circuit-breaker have to be stored prior to use , it should be done in the despatch position-
circuit-breaker switched off with closing springs discharged ( as Tab. I-A). Circuit-breaker should be
stored in the original packing.
Store indoors, in a dry , dust-free , and well ventilated room, avoiding direct sunlight.
http://www.sea.com.ua
16
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
6. Installation
6.1. Preparatory activities
The construction works in the room must be finished, being the place dry, dust-free and having a good
ventilation.
Connect the main terminals only after the circuit-breaker fixation in the normal service position .
Make a circuit-breaker general cleaning removing any contamination , specially on insulating parts.
Check the integrity of primary and secondary connections and earth conductor connection .
6.2. Installation process ( fixed versions )
Prior to begin circuit-breaker installation , check if the primary voltage is off
The operations are the following :
Circuit-breaker fixation in the normal service position ( see figs. 2, 3 e 4 ), using tensile class 8.8
screws with correct thread size and conical spring washers . Apply the recommended rated
tightening torque .
Connect the earth conductor with recommended section to the circuit-breaker frame, using terminal
with symbol ( ) - see figs. 2 e 3. In the Normacel panel Withdrawable version , the earth
connection is always done when the breaker is in the panel.
Connect the main terminals, avoiding any permanent tension or pressure forces exerted, for
example, by the conductor bars .Use tensile class 8.8 screws with conical spring washers for
fastening conductor bars together.
After removing the front panel, insert the auxiliary conductors in the operating mechanism
compartment using the hole ( see figs. 4-1 a 4-3) in the frame base. Connect conductors according the
electrical wiring scheme supplied with the circuit-breaker. The auxiliary conductors must have the
necessary section and insulation for the fixed installation ( test voltage 3 kV ). Outside circuit-
breaker, the auxiliary circuits should be protected and installed in gutters with an earth connection .
Put the operating mechanism front cover in the original position
http://www.sea.com.ua
17
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
6.3. Commissioning - Preparatory checking
Check the tightness of the connections.
Check the primary and secondary connections and the earthing conductor connections .
Manually charge the closing springs using the recharging handle .
Perform a manual closing and opening operation on the circuit-breaker, using the front panel push-
buttons . Observe the compliance between the operation and the switch position and closing spring
charge conditions indicators ( see Tab. I).
Note: If the circuit-breaker is equipped with under voltage trip solenoid, it is necessary to attach the
solenoid core in the spring compressed position, until the auxiliary circuits voltage be on,
otherwise the circuit-breaker will open immediately after a closing operation.
Check if the auxiliary circuits voltage is the same as the equipment .
Connect the auxiliary voltage circuits.
In versions fitted with a recharging motor, closing springs automatically recharging will be
performed whenever closing are discharged.. Check for automatically recharging performance,
making a closing and opening sequence .
Check for opening and closing solenoids performance.
After the successful completion of these preliminary checkings, the circuit-breaker is ready for service.
http://www.sea.com.ua
18
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
7. Inspection and Maintenance
Maintenance work may only be performed in a careful manner by trained personal familiar with the
characteristics of the circuit-breaker and safety regulations.
Before any circuit-breaker maintenance activity, observe the following procedure:
Ensure that circuit-breaker is switched off with closing springs discharged , as Tab.I-A (in motorised
versions disconnected all auxiliary voltage sources, to prevent automatic recharge ).
In fixed installation versions , disconnected the main and auxiliary voltage sources .
For the Normacel panel versions, remove the circuit-breaker from the switchgear cubicle.
7.1 General
Divac circuit-breakers are characterised by a high reliability and long life expectancy due to their
simple and robust construction .
As Divac vacuum circuit-breakers need low operation energy, the operating mechanism has low wear
and that means a long useful life and longer intervals between maintenance inspection.
In normal operating conditions , the poles , including the vacuum interrupters , are maintenance free
7.2 Electrical working life
The vacuum interrupters electrical working life depends on the performed operating cycles number
(n) and on the breaking current, as fig.11.
100000
10000
1000
100
10
1
100 1000 10000 100000
Breaking current (A)
fig.11
http://www.sea.com.ua
19
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
7.3 Periodic inspection
A long working life and the interval of inspections , are determined by operating conditions , switching
frequency, number of short-circuit breaking operations and environmental influences .
If the installation or operating conditions are more severe than the ones stated in this manual, the
inspection interval must be shortened.
To have the guaranty of a good pole insulation , it will be necessary make a periodic careful cleaning ,
removing all the surface contamination.
The periodic inspections and preventive maintenance intervals, in a normal utilisation, are the following:
After 1 year or 2 000 switching operations
Circuit-breaker:
- Visual inspection , checking damage signals or corrosion
- Carefully cleaning with a soft dry cloth, removing all the surface dust specially in the poles
Operating mechanism :
- Remove front cover
- Visual inspection , checking for excessive wear in the mechanical components
- Check the condition of lubrication
Every 5 years or after 5 000 switching operations
Circuit-breaker:
- Visual inspection , checking for damage or corrosion signals
- Carefully cleaning of poles surface, removing all the dust from the poles with a soft dry cloth
Operating mechanism:
- Remove frontal cover
- Inspection , checking the wear in the mechanical components
- Clean with a cloth soaked in white-spirit the operating mechanism before lubrication
- Lubricate the points marked in fig.12 .
After 20 years or after 10.000 switching operations
- Possible replacement of highly stressed parts.
- Possible replacement of vacuum interrupters.
For a more demanding degree of operations (e.g. 30 000 operations), periodic inspections and
preventive maintenance intervals will be defined according each request.
http://www.sea.com.ua
20
http://www.sea.com.ua 02094, ., . , 13-, .2
./ : (044) 291-00-20
7.4 Lubrication
Lubricate with a thin layer of Mobilgrease Special from Mobil the points marked with in fig.12.
fig. 12
7.5 Replacement parts
The parts, signalled with * at the table, replacement must be performed by EFACEC Medium
Voltage
Switchgear Division - After-Sales department personnel.
Orders for replacement parts request the following information:
All the information of circuit-breaker nameplates (type of circuit-breaker, serial number, work order ,etc.)
Reference number ( like Tab. II) and desired parts quantity
Voltage source value and kind of current (d.c. or a.c.) of auxiliary circuits
Code Description
1 * Complete pole
2 * Closing solenoid
3 * Opening solenoid
4 * Additional opening solenoid
9 Undervoltage tripping solenoid (AFT)
6 Recharging motor
7 Recharging motor fuse
8 Anti-pumping relay
9 Auxiliary contacts block
10 * Damper
11 Closing interlock
12 Auxiliary contacts
Tab. II - Replaceable parts