Extreme Networks, Inc. Or its subsidiaries are trademarks or registered trademarks in the United States and / or other countries. SFlow is a registered trademark of InMon Corporation. The sFlow name is a trademark of reachnxt, servicewatch, and Summit stack.
Extreme Networks, Inc. Or its subsidiaries are trademarks or registered trademarks in the United States and / or other countries. SFlow is a registered trademark of InMon Corporation. The sFlow name is a trademark of reachnxt, servicewatch, and Summit stack.
Extreme Networks, Inc. Or its subsidiaries are trademarks or registered trademarks in the United States and / or other countries. SFlow is a registered trademark of InMon Corporation. The sFlow name is a trademark of reachnxt, servicewatch, and Summit stack.
Santa Clara, California 95051 (888) 257-3000 (408) 579-2800 http://www.extremenetworks.com
Wireless Mobility 5.4 CLI Reference Guide Software Version 5.4 Published: January 2013 Part number: 120811-00 Rev 1
Wireless Mobility 5.4 CLI Reference Guide 2 AccessAdapt, Alpine, Altitude, BlackDiamond, EPICenter, ExtremeWorks Essentials, Ethernet Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby Router Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go Purple Extreme Solution, ExtremeXOS ScreenPlay, ReachNXT, Sentriant, ServiceWatch, Summit, SummitStack, Triumph, Unified Access Architecture, Unified Access RF Manager, UniStack, the Extreme Networks logo, the Alpine logo, the BlackDiamond logo, the Extreme Turbodrive logo, the Summit logos, and the Powered by ExtremeXOS logo are trademarks or registered trademarks of Extreme Networks, Inc. or its subsidiaries in the United States and/or other countries. sFlow is a registered trademark of InMon Corporation. Specifications are subject to change without notice. All other registered trademarks, trademarks, and service marks are property of their respective owners. 2012 Extreme Networks, Inc. All Rights Reserved.
Wireless Mobility 5.4 CLI Reference Guide 3 Table of Contents Chapter 1: About This Guide..................................................................................................................... 1 Documentation Set ...................................................................................................................................................1 Document Conventions ............................................................................................................................................2 Notational Conventions ............................................................................................................................................2 Understanding Command Syntax .....................................................................................................................2 Chapter 2: Introduction.............................................................................................................................. 5 CLI Overview............................................................................................................................................................6 Command Modes..............................................................................................................................................7 Getting Context Sensitive Help ................................................................................................................................9 Using the No Command.........................................................................................................................................11 Basic Conventions ..........................................................................................................................................11 Using CLI Editing Features and Shortcuts .............................................................................................................11 Moving the Cursor on the Command Line.......................................................................................................11 Completing a Partial Command Name............................................................................................................12 Command Output pagination ..........................................................................................................................13 Creating Profiles..............................................................................................................................................13 Change the default profile by creating vlan 150 and mapping to ge3 Physical interface................................13 Viewing Configured APs ..........................................................................................................................14 Remote Administration....................................................................................................................................14 Configuring Telnet for Management Access............................................................................................14 Configuring ssh........................................................................................................................................16 Chapter 3: User Exec Mode Commands ................................................................................................ 19 User Exec Commands............................................................................................................................................20 ap-upgrade......................................................................................................................................................21 change-passwd...............................................................................................................................................26 clear ................................................................................................................................................................27 clock ................................................................................................................................................................31 cluster..............................................................................................................................................................32 connect............................................................................................................................................................33 crypto ..............................................................................................................................................................35 disable.............................................................................................................................................................47 enable .............................................................................................................................................................48 exit...................................................................................................................................................................49 logging.............................................................................................................................................................50 mint .................................................................................................................................................................52 no ....................................................................................................................................................................54 page ................................................................................................................................................................58 ping .................................................................................................................................................................59 ssh...................................................................................................................................................................60 telnet ...............................................................................................................................................................61 terminal ...........................................................................................................................................................62 time-it ..............................................................................................................................................................63 traceroute........................................................................................................................................................64 watch...............................................................................................................................................................66
Table of Contents Wireless Mobility 5.4 CLI Reference Guide 11 crl-check........................................................................................................................................................919 ldap-group-verification...................................................................................................................................920 ldap-server ....................................................................................................................................................920 local ...............................................................................................................................................................922 nas ................................................................................................................................................................923 no ..................................................................................................................................................................924 proxy .............................................................................................................................................................927 session-resumption.......................................................................................................................................929 use ................................................................................................................................................................929 radius-user-pool-policy .........................................................................................................................................930 user ...............................................................................................................................................................931 no ..................................................................................................................................................................932 Chapter 19: Radio QoS Policy............................................................................................................... 935 radio-qos-policy ....................................................................................................................................................936 accelerated-multicast ....................................................................................................................................936 admission-control ..........................................................................................................................................937 no ..................................................................................................................................................................939 wmm..............................................................................................................................................................942 Chapter 20: Role Policy ......................................................................................................................... 945 role-policy .............................................................................................................................................................946 default-role ....................................................................................................................................................946 no ..................................................................................................................................................................948 user-role........................................................................................................................................................950 user-role.................................................................................................................................................950 user-role commands ..............................................................................................................................951 Chapter 21: Smart RF Policy ................................................................................................................. 965 smart-rf-policy.......................................................................................................................................................966 assignable-power ..........................................................................................................................................966 auto-assign-sensor........................................................................................................................................967 channel-list ....................................................................................................................................................968 channel-width................................................................................................................................................969 coverage-hole-recovery ................................................................................................................................971 enable ...........................................................................................................................................................972 group-by ........................................................................................................................................................973 interference-recovery ....................................................................................................................................974 neighbor-recovery .........................................................................................................................................976 no ..................................................................................................................................................................978 sensitivity.......................................................................................................................................................980 smart-ocs-monitoring ....................................................................................................................................981 smart-ocs-monitoring ....................................................................................................................................984 Chapter 22: WIPS Policy........................................................................................................................ 987 wips-policy............................................................................................................................................................988 ap-detection ..................................................................................................................................................988 enable ...........................................................................................................................................................989 event .............................................................................................................................................................990 history-throttle-duration .................................................................................................................................994 no ..................................................................................................................................................................995 signature .......................................................................................................................................................999 signature ................................................................................................................................................999 signature mode commands..................................................................................................................1000 use ..............................................................................................................................................................1013
Table of Contents Wireless Mobility 5.4 CLI Reference Guide 12 Chapter 23: WLAN QoS Policy............................................................................................................ 1015 wlan-qos-policy...................................................................................................................................................1016 accelerated-multicast ..................................................................................................................................1016 classification................................................................................................................................................1018 multicast-mask ............................................................................................................................................1019 no ................................................................................................................................................................1020 qos ..............................................................................................................................................................1023 rate-limit ......................................................................................................................................................1024 svp-prioritization..........................................................................................................................................1026 voice-prioritization .......................................................................................................................................1027 wmm............................................................................................................................................................1027 Chapter 24: Interface Radio Commands ............................................................................................ 1031 interface-radio Instance......................................................................................................................................1032 ack-timeout..................................................................................................................................................1033 aggregation .................................................................................................................................................1034 airtime-fairness............................................................................................................................................1037 antenna-gain ...............................................................................................................................................1037 antenna-mode.............................................................................................................................................1038 beacon ........................................................................................................................................................1039 channel........................................................................................................................................................1041 data-rates ....................................................................................................................................................1042 description...................................................................................................................................................1044 dynamic-chain-selection..............................................................................................................................1045 guard-interval ..............................................................................................................................................1046 lock-rf-mode ................................................................................................................................................1047 max-clients ..................................................................................................................................................1047 mesh ...........................................................................................................................................................1048 no ................................................................................................................................................................1050 non-unicast..................................................................................................................................................1053 off-channel-scan..........................................................................................................................................1055 placement....................................................................................................................................................1057 power ..........................................................................................................................................................1057 preamble-short ............................................................................................................................................1058 probe-response...........................................................................................................................................1059 radio-tap-mode............................................................................................................................................1060 rf-mode........................................................................................................................................................1061 rifs ...............................................................................................................................................................1062 rts-threshold ................................................................................................................................................1063 shutdown.....................................................................................................................................................1064 sniffer-redirect .............................................................................................................................................1064 use ..............................................................................................................................................................1065 wireless-client..............................................................................................................................................1066 wlan.............................................................................................................................................................1067 Chapter 25: Firewall Logging .............................................................................................................. 1069 Firewall Log Terminology and Syslog Severity Levels .......................................................................................1070 Date format in Syslog messages ................................................................................................................1070 FTP data connection log .............................................................................................................................1071 The FTP connection is Control Connection .........................................................................................1071 The Data Connection in Active Mode ..................................................................................................1071 The Data Connection in Passive Mode................................................................................................1071 UDP packets log .........................................................................................................................................1072 DHCP Release.....................................................................................................................................1072 DHCP Renew.......................................................................................................................................1072 ICMP type logs............................................................................................................................................1072 ICMP type logs............................................................................................................................................1073
Table of Contents Wireless Mobility 5.4 CLI Reference Guide 13 Raw IP Protocol logs.................................................................................................................................1074 Raw IP Protocol logs..................................................................................................................................1075 Firewall startup log......................................................................................................................................1075 Manual time change log..............................................................................................................................1076 Firewall ruleset log ......................................................................................................................................1077 IP ACL IN on WLAN Attach ...............................................................................................................1077 IP ACL IN on WLAN Remove ..............................................................................................................1077 IP ACL OUT on WLAN Attach .............................................................................................................1077 IP ACL OUT on WLAN Remove ..........................................................................................................1077 MAC ACL IN on WLAN Attach.............................................................................................................1078 MAC ACL IN on WLAN Remove..........................................................................................................1078 MAC ACL OUT on WLAN Attach.........................................................................................................1078 MAC ACL OUT on WLAN Remove......................................................................................................1078 IP ACL on VLAN Attach.......................................................................................................................1078 IP ACL on VLAN Remove....................................................................................................................1078 IP ACL on GE Port Attach....................................................................................................................1078 IP ACL on GE Port Remove ................................................................................................................1078 MAC ACL on GE Port Attach...............................................................................................................1078 MAC ACL on GE Port Remove............................................................................................................1079 IP ACL on Port-Channel Attach ...........................................................................................................1079 IP ACL on Port-Channel Remove........................................................................................................1079 MAC ACL on Port-Channel Attach.......................................................................................................1079 MAC ACL on Port-Channel Remove ...................................................................................................1079 Rule added / deleted from IP/MAC ACL ..............................................................................................1079 TCP Reset Packets log...............................................................................................................................1079 ICMP Destination log ..................................................................................................................................1080 ICMP Packet log .........................................................................................................................................1080 SSH connection log.....................................................................................................................................1080 Allowed/Dropped Packets Log....................................................................................................................1081 Drop/Deny Packets ..............................................................................................................................1082 Chapter 26: L2TPV3-Policy.................................................................................................................. 1083 l2tpv3-policy-commands.....................................................................................................................................1085 cookie-size ..................................................................................................................................................1086 hello-interval ................................................................................................................................................1087 no ................................................................................................................................................................1088 reconnect-attempts .....................................................................................................................................1090 reconnect-interval........................................................................................................................................1091 retry-attempts ..............................................................................................................................................1092 retry-interval ................................................................................................................................................1093 rx-window-size ............................................................................................................................................1094 tx-window-size.............................................................................................................................................1095 l2tpv3-tunnel-commands ....................................................................................................................................1096 hostname ....................................................................................................................................................1098 local-ip-address...........................................................................................................................................1099 mtu ..............................................................................................................................................................1100 no ................................................................................................................................................................1101 peer .............................................................................................................................................................1103 router-id.......................................................................................................................................................1105 session........................................................................................................................................................1106 use ..............................................................................................................................................................1108 l2tpv3-manual-session-commands.....................................................................................................................1109 local-cookie .................................................................................................................................................1111 local-ip-address...........................................................................................................................................1112 local-session-id ...........................................................................................................................................1113 mtu ..............................................................................................................................................................1114 no ................................................................................................................................................................1115 peer .............................................................................................................................................................1118
Table of Contents Wireless Mobility 5.4 CLI Reference Guide 14 remote-cookie .............................................................................................................................................1119 remote-session-id........................................................................................................................................1121 traffic-source ...............................................................................................................................................1122 Chapter 27: Router-Mode Commands................................................................................................ 1125 router-mode........................................................................................................................................................1126 area.............................................................................................................................................................1127 auto-cost .....................................................................................................................................................1129 default-information ......................................................................................................................................1130 ip .................................................................................................................................................................1131 network........................................................................................................................................................1132 ospf .............................................................................................................................................................1133 passive........................................................................................................................................................1134 redistribute ..................................................................................................................................................1135 route-limit ....................................................................................................................................................1136 router-id.......................................................................................................................................................1138 vrrp-state-check ..........................................................................................................................................1139 no ................................................................................................................................................................1140 OSPF-area-mode........................................................................................................................................1141 area-type..............................................................................................................................................1142 authentication.......................................................................................................................................1143 range....................................................................................................................................................1144 no.........................................................................................................................................................1145 Chapter 28: Routing-Policy Commands............................................................................................. 1147 routing-policy Commands...................................................................................................................................1148 apply-to-local-packets .................................................................................................................................1149 logging.........................................................................................................................................................1150 route-map....................................................................................................................................................1151 route-map-mode..........................................................................................................................................1152 default-next-hop...................................................................................................................................1153 fallback.................................................................................................................................................1154 mark .....................................................................................................................................................1155 match ...................................................................................................................................................1156 next-hop...............................................................................................................................................1158 no.........................................................................................................................................................1159 use ..............................................................................................................................................................1160 no ................................................................................................................................................................1161 Chapter 29: AAA-TACACS Policy ....................................................................................................... 1163 aaa-tacacs-policy ...............................................................................................................................................1164 accounting...................................................................................................................................................1165 authentication..............................................................................................................................................1168 authorization................................................................................................................................................1170 no ................................................................................................................................................................1173 Appendix A: Controller Managed WLAN Use Case........................................................................... 1175 Creating a First Controller Managed WLAN.......................................................................................................1175 Assumptions................................................................................................................................................1175 Design.........................................................................................................................................................1176 Using the Command Line Interface to Configure the WLAN.......................................................................1176 Logging Into the Controller for the First Time ......................................................................................1177 Creating a RF Domain .........................................................................................................................1177 Creating a Wireless Controller Profile..................................................................................................1178 Creating an AP Profile .........................................................................................................................1179 Creating a DHCP Server Policy ...........................................................................................................1182 Completing and Testing the Configuration...........................................................................................1183
Table of Contents Wireless Mobility 5.4 CLI Reference Guide 16
Wireless Mobility 5.4 CLI Reference Guide 1 C H A P T E R 1 About This Guide This manual supports the following wireless controllers and access points: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Documentation Set The documentation set for the Extreme Networks Wireless Controllers is partitioned into the following guides to provide information for specific user needs. Altitude Access Point Installation Guide - Describes the basic hardware and configuration setup required to transition to a more advanced configuration of the access point. The installation guide is unique to the particular access point model purchased Wireless Mobility 5.4 Access Point System Reference Guide - Describes the configuration of either a Standalone AP or Virtual Controller AP using the access points initial setup wizard and resident access point specific software. Wireless Mobility 5.4 Controller System Reference Guide - Describes the configuration of a Dependent mode AP using the controller software. Wireless Mobility 5.4 CLI Reference Guide - Describes the commands supported by the Summit WM3000 Series Controllers and Altitude Access Points that support a command line interface. For information on managing a dependent mode AP in a controller managed network, go to http:// www.extremenetworks.com/go/documentation.
Chapter 1: About This Guide Wireless Mobility 5.4 CLI Reference Guide 2 Document Conventions The following conventions are used in this document to draw your attention to important information: NOTE Indicate tips or special requirements. CAUTION Indicates conditions that can cause equipment damage or data loss. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage. Notational Conventions The following notational conventions are used in this document: Italics are used to highlight specific items in the general text, and to identify chapters and sections in this and related documents Bullets () indicate: lists of alternatives lists of required steps that are not necessarily sequential action items Sequential lists (those describing step-by-step procedures) appear as numbered lists Understanding Command Syntax <variable> Variables are described with a short description enclosed within a < and a > pair. For example, the command, wm3700-37FABE>show interface ge 1 is documented as show interface ge <1-4> show The command Display information interface The keyword The interface <1-4> The variable get Index value
Notational Conventions Wireless Mobility 5.4 CLI Reference Guide 3 The pipe symbol is used to separate the variables/keywords in a list. For example, the command wm3700-37FABE> show ..... is documented as show [adoption|advanced-wips|captive- portal......] where: show The command [adoption|advanced-wips|boot|captive-portal......] Indicates the different commands that can be combined with the show command. However, only one of the above list can be used at a time. show adoption ... show advanced-wips ... show boot ... [] Of the different keywords and variables listed inside a [ & ] pair, only one can be used. Each choice in the list is separated with a (pipe) symbol. For example, the command wm3700-37FABE# clear ... is documented as clear [arp-cachecdpcounterscryptoevent- historyfirewallipl2tpv3- statslldploggingrtlsspanning-treevrrp] where: clear The command [arp-cache|cdp|counters|crypto|event-history|firewall|ipl2tpv3-stats lldp|logging|rtls|spanning-tree|vrrp] Indicates that thirteen keywords are available for this command but only one can be used at a time { } Any command/keyword/variable or a combination of these inside a { & } pair is optional. All optional commands follow the same conventions as listed above. However, they are displayed italicized. For example, the command wm3700-37FABE> show adoption .... is documented as show adoption info {on <DEVICE-NAME>} Here: show adoption info The command. This command can also be used as show adoption info {on <DEVICE-NAME>} The optional keyword on <device-or- domain-name>. The command can also be extended as show adoption info {on <DEVICE-NAME>} Here the keyword {on <DEVICE-OR-DOMAIN-NAME>} is optional.
Chapter 1: About This Guide Wireless Mobility 5.4 CLI Reference Guide 4 command / keyword The first word is always a command. Keywords are words that must be entered as is. Commands and keywords are mandatory. For example, the command, wm3700-37FABE>show wireless is documented as show wireless where: show The command wireless The keyword () Any command/keyword/variable or a combination of these inside a ( & ) pair are recursive. All recursive commands can be listed in any order and can be used once along with the rest of the commands. For example, the command crypto pki export request generate-rsa-key test autogen-subject-name ... is documented as wm3700-37FABE#crypto pki export request generate-rsa-key test autogen-subject-name (<URL>,email <EMAIL>,fqdn <FQDN>,ip-address <IP>) Here: crypto pki export request generate-rsa-key <RSA-KEYPAIR-NAME> auto-gen-subject-name The command wm3700-37FABE#crypto pki export request generate-rsa-key test autogen-subject-name <RSA-KEYPAIR-NAME> The RSA keypair name (in this example, the keypair name is test) (<URL>,email <EMAIL>,fqdn <FQDN>,ip-address <IP>) The set of recursive parameters that can be used in any order. where every recursive command is separated by a comma ,
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 5 C H A P T E R 2 Introduction This chapter describes the commands available using the wireless controller Command Line Interface (CLI). CLI is available for wireless controllers as well as access points (APs). Access the CLI by using: A terminal emulation program running on a computer connected to the serial port on the wireless controller. The serial port is located on the front of the wireless controller. A Telnet session through Secure Shell (SSH) over a network. Configuration for connecting to a Wireless Controller using a terminal emulator If connecting through the serial port, use the following settings to configure your terminal emulator: When a CLI session is established, complete the following (user input is in bold): login as: <username> administrators login password: <password> User Credentials Use the following credentials when logging into a device for the first time: When logging into the CLI for the first time, you are prompted to change the password. Bits Per Second 19200 Data Bits 8 Parity None Stop Bit 1 Flow Control None User Name admin Password admin123
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 6 Examples in this reference guide Examples used in this reference guide are generic to the each supported wireless controller model and AP. Commands that are not common, are identified using the notation Supported in the following platforms. For an example, see below: Supported on the following platforms: WM3600 The above example indicates the command is only available for a WM3600 model wireless controller. CLI Overview The CLI is used for configuring, monitoring, and maintaining the wireless controller managed network. The user interface allows you to execute commands on supported wireless controllers and APs, using either a serial console or a remote access method. This chapter describes basic CLI features. Topics covered include an introduction to command modes, navigation and editing features, help features and command history. The CLI is segregated into different command modes. Each mode has its own set of commands for configuration, maintenance and monitoring. The commands available at any given time depend on the mode you are in, and to a lesser extent, the particular model used. Enter a question mark (?) at the system prompt to view a list of commands available for each command mode/instance. Use specific commands to navigate from one command mode to another. The standard order is: USER EXEC mode, PRIV EXEC mode and GLOBAL CONFIG mode.
CLI Overview Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 7 Figure 2-1 Hierarchy of User Modes Command Modes A session generally begins in the USER EXEC mode (one of the two access levels of the EXEC mode). For security, only a limited subset of EXEC commands are available in the USER EXEC mode. This level is reserved for tasks that do not change the wireless controller configuration. wm3700-37FABE> The system prompt signifies the device name and the last three bytes of the device MAC address. To access commands, enter the PRIV EXEC mode (the second access level for the EXEC mode). Once in the PRIV EXEC mode, enter any EXEC command. The PRIV EXEC mode is a superset of the USER EXEC mode. wm3700-37FABE> enable wm3700-37FABE# Most of the USER EXEC mode commands are one-time commands and are not saved across wireless controller reboots. Save the command by executing commit command. For example, the show command displays the current configuration and the clear command clears the interface. Access the GLOBAL CONFIG mode from the PRIV EXEC mode. In the GLOBAL CONFIG mode, enter commands that set general system characteristics. Configuration modes, allow you to change the running configuration. If you save the configuration later, these commands are stored across wireless controller reboots. Access a variety of protocol specific (or feature-specific) modes from the global configuration mode. The CLI hierarchy requires you to access specific configuration modes only through the global configuration mode. wm3700-37FABE# configure terminal Enter configuration commands, one per line. End with CNTL/Z. wm3700-37FABE(config)# You can also access sub-modes from the global configuration mode. Configuration sub-modes define specific features within the context of a configuration mode. wm3700-37FABE(config)# aaa-policy test wm3700-37FABE(config-aaa-policy-test)# Table 2 summarizes available wireless controller commands Table 2: Command Summary User Exec Mode Priv Exec Mode Global Configuration Mode ap-upgrade ap-upgrade aaa-policy captive-portal-page-upload archive aaa-tacacs-policy change-passwd boot advanced-wips-policy clock cd ap4021 cluster change-passwd ap4600 commit clear ap4511
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 8 connect clock ap4521 create-cluster cluster ap4521 crypto commit ap4522 debug configure ap4532 disable connect ap4700 enable copy association-acl-policy help create-cluster auto-provisioning-policy join-cluster crypto captive-portal l2tpv3 debug clear logging delete customize mint diff device no dir device-categorization page disable dhcp-server policy ping edit dns-whitelist remote-debug disable dhcp-sever-policy revert enable event-system-policy service enable firewall-policy show format help ssh halt host telnet help igmp-snoop-policy terminal join-cluster inline-password-encryption time-it l2tpv3 ip traceroute logging l2tpv3 watch mint mac write mkdir management-policy clrscr more meshpoint exit no meshpoint-qos-policy ping password-encryption pwd profile re-elect password-encryption reload radio-qos-policy remote-debug radius-group rename radius-server-policy revert radius-user-pool-policy rmdir rf-domain self wm3400 service wm3600 show wm3700 ssh role-policy telnet WM3950 terminal smart-rf-policy Table 2: Command Summary User Exec Mode Priv Exec Mode Global Configuration Mode
Getting Context Sensitive Help Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 9 Getting Context Sensitive Help Enter a question mark (?) at the system prompt to display a list of commands available for each mode. Obtain a list of arguments and keywords for any command using the CLI context-sensitive help. Use the following commands to obtain help specific to a command mode, command name, keyword or argument: NOTE The system prompt varies depending on the configuration mode. NOTE Enter Ctrl + V to use ? as a regular character and not as a character used for displaying context sensitive help. This is required when the user has to enter a URL that ends with a ? time-it wips-policy traceroute self upgrade wlan-qos-policy upgrade-abort write watch clrscr write commit clrscr do exit end exit revert service show Command Description (prompt)# help Displays a brief description of the help system (prompt)# abbreviated-command-entry? Lists commands in the current mode that begin with a particular character string (prompt)# abbreviated-command-entry<Tab> Completes a partial command name (prompt)# ? Lists all commands available in the command mode (prompt)# command ? Lists the available syntax options (arguments and keywords) for the command (prompt)# command keyword ? Lists the next available syntax option for the command Table 2: Command Summary User Exec Mode Priv Exec Mode Global Configuration Mode
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 10 NOTE The escape character used throughout the CLI is \. To enter a "\" use "\\" instead. When using context-sensitive help, the space (or lack of a space) before the question mark (?) is significant. To obtain a list of commands that begin with a particular sequence, enter the characters followed by a question mark (?). Do not include a space. This form of help is called word help, because it completes a word. wm3700-37FABE#service? service Service Commands wm3700-37FABE#service Enter a question mark (?) (in place of a keyword or argument) to list keywords or arguments. Include a space before the ?. This form of help is called command syntax help. It shows the keywords or arguments available based on the command/keyword and argument already entered. wm3700-37FABE>service ? advanced-wips Advanced WIPS service commands clear Remove cli-tables-skin Choose a formatting layout/skin for CLI tabular outputs cluster Cluster Protocol delete-offline-aps Delete Access Points that are configured but offline enable Enable radiusd loading on low memory devices force-send-config Resend configuration to the device load-balancing Wireless load-balancing service commands locator Enable leds flashing on the device radio Radio parameters show Show running system information smart-rf Smart-RF Management Commands ssm Command related to ssm traceroute Trace route to destination wireless Wireless commands wm3700-37FABE>service Its possible to abbreviate commands and keywords to allow a unique abbreviation. For example, configure terminal can be abbreviated as config t. Since the abbreviated command is unique, the wireless controller accepts the abbreviation and executes the command. Enter the help command (available in any command mode) to provide the following description: wm3700-37FABE>help CLI provides advanced help feature. When you need help, anytime at the command line please press '?'. If nothing matches, the help list will be empty and you must backup until entering a '?' shows the available options. Two styles of help are provided: 1. Full help is available when you are ready to enter a command argument (e.g. 'show ?') and describes each possible argument.
Using the No Command Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 11 2. Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (e.g. 'show ve?'.) Using the No Command Almost every command has a no form. Use no to disable a feature or function or return it to its default value. Use the command without the no keyword to re-enable a disabled feature. Basic Conventions Keep the following conventions in mind while working within the wireless controller CLI: Use ? at the end of a command to display available sub-modes. Type the first few characters of the sub-mode and press the tab key to add the sub-mode. Continue using ? until you reach the last sub- mode. Pre-defined CLI commands and keywords are case-insensitive: cfg = Cfg = CFG. However (for clarity), CLI commands and keywords are displayed (in this guide) using mixed case. For example, apPolicy, trapHosts, channelInfo. Enter commands in uppercase, lowercase, or mixed case. Only passwords are case sensitive. Using CLI Editing Features and Shortcuts A variety of shortcuts and edit features are available. The following describe these features: Moving the Cursor on the Command Line Completing a Partial Command Name Command Output pagination Moving the Cursor on the Command Line Table 3 shows the key combinations or sequences to move the command line cursor. Ctrl defines the control key, which must be pressed simultaneously with its associated letter key. Esc means the escape key (which must be pressed first), followed by its associated letter key. Keys are not case sensitive. Specific letters are used to provide an easy way of remembering their functions. In Table 3, bold characters indicate the relation between a letter and its function. Table 3: Command Line Keystrokes Keystrokes Function Summary Function Details Left Arrow or Ctrl-B Back character Moves the cursor one character to the left When entering a command that extends beyond a single line, press the Left Arrow or Ctrl-B keys repeatedly to move back to the system prompt. Right Arrow or Ctrl-F Forward character Moves the cursor one character to the right
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 12 Completing a Partial Command Name If you cannot remember a command name (or if you want to reduce the amount of typing you have to perform), enter the first few letters of a command, then press the Tab key. The command line parser completes the command if the string entered is unique to the command mode. If your keyboard does not have a Tab key, press Ctrl-L. The CLI recognizes a command once you have entered enough characters to make the command unique. If you enter conf within the privileged EXEC mode, the CLI associates the entry with the configure command, since only the configure command begins with conf. In the following example, the CLI recognizes a unique string in the privileged EXEC mode when the Tab key is pressed: wm3700-37FABE# conf<Tab> wm3700-37FABE# configure When using the command completion feature, the CLI displays the full command name. The command is not executed until the Return or Enter key is pressed. Modify the command if the full command was not what you intended in the abbreviation. If entering a set of characters (indicating more than one command), the system lists all commands beginning with that set of characters. Enter a question mark (?) to obtain a list of commands beginning with that set of characters. Do not leave a space between the last letter and the question mark (?). For example, entering U lists all commands available in the current command mode: wm3700-37FABE# co? Esc- B Back word Moves the cursor back one word Esc- F Forward word Moves the cursor forward one word Ctrl-A Beginning of line Moves the cursor to the beginning of the command line Ctrl-E End of line Moves the cursor to the end of the command line Ctrl-D Deletes the current character Ctrl-U Deletes text up to cursor Ctrl-K Deletes from the cursor to end of the line Ctrl-P Obtains the prior command from memoryTable 3 Ctrl-N Obtains the next command from memory Esc-C Converts the letter at the cursor to uppercase Esc-L Converts the letter at the cursor to lowercase Esc-D Deletes the remainder of a word Ctrl-W Deletes the word up to the cursor Ctrl-Z Returns to the root prompt Ctrl-T Transposes the character to the left of the cursor with the character located at the cursor Ctrl-L Clears the screen Table 3: Command Line Keystrokes Keystrokes Function Summary Function Details
Using CLI Editing Features and Shortcuts Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 13 commit Commit all changes made in this session configure Enter configuration mode connect Open a console connection to a remote device copy Copy from one file to another wm3700-37FABE# co NOTE The characters entered before the question mark are reprinted to the screen to complete the command entry. Command Output pagination Output often extends beyond the visible screen length. For cases where output continues beyond the screen, the output is paused and a --More-- prompt displays at the bottom of the screen. To resume the output, press the Enter key to scroll down one line or press the Spacebar to display the next full screen of output. Creating Profiles Profiles are sort of a template representation of configuration. The system has: a default wireless controller profile a default profile for each of the following APs: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 To modify the default profile to assign an IP address to the management port: wm3700-37FABE(config)#profile wm3700 default-wm-3700 wm3700-37FABE(config-profile-default-wm-3700)#interface me1 wm3700-37FABE(config-profile-default-wm-3700-if-me1)#ip address 172.16.10.2/24 wm3700-37FABE(config-profile-default-wm-3700-if-me1)#commit wm3700-37FABE(config-profile-default-wm-3700)#exit wm3700-37FABE(config)# The following command displays default ap4700 profile: wm3700-37FABE(config)#profile ap4700 default-ap4700 wm3700-37FABE(config-profile-default-ap4700)#show context
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 14 Change the default profile by creating vlan 150 and mapping to ge3 Physical interface Logon to the wireless controller in config mode and follow the procedure below: wm3700-37FABE(config-profile-default-wm3700)# interface vlan 150 wm3700-37FABE(config-profile-default-wm3700-if-vlan150)# ip address 192.168.150.20/24 wm3700-37FABE(config-profile-default-wm3700-if-vlan150)# exit wm3700-37FABE(config-profile-default-wm3700)# interface ge 3 wm3700-37FABE(config-profile-default-wm3700-if-ge3)# switchport access vlan 150 wm3700-37FABE(config-profile-default-wm3700-if-ge3)# commit write [OK] wm3700-37FABE(config-profile-default-wm3700-if-ge3)# show interface vlan 150 Interface vlan150 is UP Hardware-type: vlan, Mode: Layer 3, Address: 00-15-70-37-FA-BE Index: 8, Metric: 1, MTU: 1500 IP-Address: 192.168.150.20/24 input packets 43, bytes 12828, dropped 0, multicast packets 0 input errors 0, length 0, overrun 0, CRC 0, frame 0, fifo 0, missed 0 output packets 0, bytes 0, dropped 0 output errors 0, aborted 0, carrier 0, fifo 0, heartbeat 0, window 0 collisions 0 Viewing Configured APs To view previously configured APs, enter the following command: wm3700-37FABE(config)#show wireless ap configured Remote Administration A terminal server may function in remote administration mode if either the terminal services role is not installed on the machine or the client used to invoke the session has enabled the admin wireless controller. A terminal emulation program running on a computer connected to the serial port on the wireless controller. The serial port is located on the front of the wireless controller. A Telnet session through a Secure Shell (SSH) over a network. The Telnet session may or may not use SSH depending on how the wireless wireless controller is configured. Extreme Networks recommends using SSH for remote administration tasks. Configuring Telnet for Management Access Login through the serial console. Perform the following: A session generally begins in the USER EXEC mode (one of the two access levels of the EXEC mode). Access the GLOBAL CONFIG mode from the PRIV EXEC mode.
Using CLI Editing Features and Shortcuts Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 15 wm3700-37FABE> en wm3700-37FABE# conf i gur e t er mi nal Enter configuration commands, one per line. End with CNTL/Z. Go to default-management-policy mode. wm3700-37FABE( conf i g) # management - pol i cy ? wm3700-37FABE( conf i g) # management - pol i cy def aul t wm3700-37FABE( conf i g- management - pol i cy- def aul t ) # Enter Telnet and the port number at the command prompt. The port number is optional. The default port is 23. Commit the changes after every command. Telnet is enabled. wm3700-37FABEconfig-management-policy-default)# telnet wm3700-37FABE(config-management-policy-default)# commit write Connect to the wireless controller through Telnet using its configured IP address. Use the following credentials when logging on to the device for the first time: When logging into the wireless controller for the first time, you are prompted to change the password. To change user credentials: Enter the username, password, role, and access details wm3700-37FABE( conf i g- management - pol i cy- def aul t ) # user t est user passwor d ext r eme r ol e hel pdesk access al l wm3700-37FABE( conf i g- management - pol i cy- def aul t ) # commi t wm3700-37FABE( conf i g- management - pol i cy- def aul t ) # show cont ext management-policy default telnet http server ssh user admin password 1 ba7da2bf2f7945af1d3ae1b8b762b541bd5bac1f80a54cd4488f38ed44b91ecd role superuser access all user operator password 1 0be97e9e30d29dfc4733e7c5f74a7be54570c2450e855cea1a696b0558a40401 role monitor access all user t est user passwor d 1 bca381b5b93cddb0c209e1da8a9d387fa09bfae14cc987438a4d144cb516ffcb role helpdesk access all snmp-server community public ro snmp-server community private rw snmp-server user snmptrap v3 encrypted des auth md5 0 extreme snmp-server user snmpoperator v3 encrypted des auth md5 0 operator snmp-server user snmpmanager v3 encrypted des auth md5 0 extreme wm3700-37FABE( conf i g- management - pol i cy- def aul t ) User Name admin Password admin123
Chapter 2: Introduction Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 16 Log on to the Telnet console and provide the user details configured in the previous step to access the wireless controller. WM3700 release 5.4.0.0-144745X wm3700-37FABE l ogi n: t est user Password: Welcome to CLI Starting CLI... wm3700-37FABE> Configuring ssh By default, SSH is enabled from the factory settings on the wireless controller. The wireless controller requires an IP address and login credentials. To enable SSH access in the default profile, login through the serial console. Perform the following: Access the GLOBAL CONFIG mode from the PRIV EXEC mode. wm3700-37FABE> en wm3700-37FABE# conf i gur e Enter configuration commands, one per line. End with CNTL/Z. wm3700-37FABE> en wm3700-37FABE# conf i gur e Enter configuration commands, one per line. End with CNTL/Z. Go to default-management-policy mode. wm3700-37FABE( conf i g) # management - pol i cy def aul t wm3700-37FABE( conf i g- management - pol i cy- def aul t ) # Enter SSH at the command prompt. wm3700-37FABE(config-management-policy-default)# ssh Log into the wireless wireless controller through SSH using appropriate credentials. Use the following credentials when logging on to the device for the first time: When logging into the wireless controller for the first time, you are prompted to change the password. To change the user credentials: WM3700 release 5.4.0.0-144745X wm3700-37FABE l ogi n: t est user Password: Welcome to CLI Starting CLI... wm3700-37FABE> User Name admin Password admin123
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 17 C H A P T E R 3 User Exec Mode Commands Logging in to the wireless controller places you within the USER EXEC command mode. Typically, a login requires a user name and password. You have three login attempts before the connection attempt is refused. USER EXEC commands (available at the user level) are a subset of the commands available at the privileged level. In general, USER EXEC commands allow you to connect to remote devices, perform basic tests and list system information. To list available USER EXEC commands, use? at the command prompt. The USER EXEC prompt consists of the device host name followed by an angle bracket (>). wm3700-37FABE>? User Exec commands: ap-upgrade AP firmware upgrade captive-portal-page-upload Captive portal advanced page upload change-passwd Change password clear Clear clock Configure software system clock cluster Cluster commands commit Commit all changes made in this session connect Open a console connection to a remote device crypto Encryption related commands debug Debugging functions disable Turn off privileged mode command enable Turn on privileged mode command help Description of the interactive help system join-cluster Join a cluster l2tpv3 L2tpv3 protocol logging Modify message logging facilities mint MiNT protocol no Negate a command or set its defaults page Toggle paging ping Send ICMP echo messages revert Revert changes service Service Commands show Show running system information ssh Open an ssh connection telnet Open a telnet connection terminal Set terminal line parameters time-it Check how long a particular command took between request and completion of response
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 18 traceroute Trace route to destination watch Repeat the specific CLI command at a periodic interval write Write running configuration to memory or terminal clrscr Clears the display screen exit Exit from the CLI wm3700-37FABE> User Exec Commands The following table summarizes User Exec Mode commands Command Description Reference ap-upgrade Enables an automatic adopted AP firmware upgrade page 3-20 captive-portal- page-upload CUploads captive portal advanced pages page 3-26 change-passwd Changes the password of a logged user page 3-20 clear Resets the last saved command page 3-30 clock Configures the system clock page 3-35 cluster Accesses the cluster context page 3-36 connect Establishes a console connection to a remote device page 3-37 create-cluster Creates a new cluster on a specified device crypto Enables encryption page 3-41 disable Turns off (disables) the privileged mode command set page 3-52 enable Turns on (enables) the privileged mode command set page 3-53 join-cluster Adds a wireless controller to an existing cluster of devices l2tpv3 Establishes or brings down Layer 2 Tunneling Protocol Version 3 (L2TPV3) tunnel mint Modifies message logging facilities page 3-61 exit Ends the current CLI session and closes the session window mint Configures MiNT protocol page 3-61 no Negates a command or sets its default value page 3-63 page Toggles to the wireless controller paging function page 3-67 ping Sends ICMP echo messages to a user-specified location page 3-68 ssh Opens an SSH connection between two network devices page 3-70 telnet Opens a Telnet session page 3-71 terminal Sets the length/number of lines displayed within the terminal window page 3-72 time-it Verifies the time taken by a particular command between request and response page 3-73 traceroute Traces the route to its defined destination page 3-74 watch Repeats a specific CLI command at a periodic interval page 3-76 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 help Displays the interactive help system page 6-383
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 19 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 20 ap-upgrade User Exec Commands Enables an automatic firmware upgrade on an adopted AP or a set of APs. APs of the same type can be upgraded together. Once APs have been upgraded, they can be forced to reboot. This command also loads the firmware on to the wireless controller. The AP upgrade command also upgrades APs in a specified RF Domain. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap-upgrade [<MAC/HOSTNAME>|all|ap4021|ap4600|ap4511|ap4521|ap4522|ap4532| ap4700|cancel-upgrade|load-image|rf-domain] ap-upgrade [<MAC/HOSTNAME>|{no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} ap-upgrade all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no- reboot|reboot-time <TIME>}} {(staggered-reboot)} ap-upgrade [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered-reboot)} ap-upgrade cancel-upgrade [<MAC/HOSTNAME>|all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|4700|on] ap-upgrade cancel-upgrade [<MAC/HOSTNAME>|all] ap-upgrade cancel-upgrade [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|4700] all ap-upgrade cancel-upgrade on rf-domain [<RF-DOMAIN-NAME>|all] ap-upgrade load-image [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] <IMAGE-URL> ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|4700] {no-reboot|no-via-rf-domain|reboot-time <TIME>|staggered-reboot|upgrade-time <TIME>}
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 21 ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|4700] {no-reboot {staggered-reboot}|reboot-time <TIME> {staggered-reboot}} ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|4700| {no-via-rf-domain {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}}} {(staggered-reboot)} ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|4700] {upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered-reboot)} Parameters ap-upgrade <MAC/HOSTNAME> {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} ap-upgrade [all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no- reboot|reboot-time <TIME>}}{{staggered-reboot}} <MAC/HOSTNAME> Upgrades firmware on a specified AP or all APs adopted by the wireless controller <MAC/HOSTNAME> Specify the MAC address or hostname of the AP. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted) reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade <TIME> Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. upgrade-time <TIME> {no-reboot|reboot-time <TIME>} Optional. Schedules an automatic firmware upgrade <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. After a scheduled upgrade, these actions can be performed. no-reboot Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. [ap4021|ap4600|ap4511| ap4522|ap4521|ap4532| ap4700] all Upgrades firmware on all adopted APs AP4021 all Upgrades firmware on all AP4021s AP4600 all Upgrades firmware on all AP4600s AP4511 all Upgrades firmware on all AP4511s AP4521 all Upgrades firmware on all AP4521s AP4522 all Upgrades firmware on all AP4522s AP4532 all Upgrades firmware on all AP4532s AP4700 all Upgrades firmware on all AP4700s After selecting the AP type, you can schedule an automatic upgrade and/or an automatic reboot. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted).
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 22 ap-upgrade [ap4021|ap4600|ap4511||ap4521|ap4522|ap4532|ap4700]all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}}{{staggered-reboot}} reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. <TIME> Optional. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. upgrade-time <TIME> {no-reboot|reboot-time <TIME>} Optional. Schedules firmware upgrade on an AP adopted by the wireless controller. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. After a scheduled upgrade, these actions can be performed. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enbales staggered reboot (one at a time) without network impact.This keyword is common to all of the above. [ap4021|ap4600|ap4511| ap4522|ap4521|ap4532| ap4700] all Upgrades firmware on all adopted APs AP4021 all Upgrades firmware on all AP4021s AP4600 all Upgrades firmware on all AP4600s AP4511 all Upgrades firmware on all AP4511s AP4521 all Upgrades firmware on all AP4521s AP4522 all Upgrades firmware on all AP4522s AP4532 all Upgrades firmware on all AP4532s AP4700 all Upgrades firmware on all AP4700s After selecting the AP type, you can schedule an automatic upgrade and/or an automatic reboot. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. <TIME> Optional. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. upgrade-time <TIME> {no-reboot|reboot-time <TIME>} Optional. Schedules firmware upgrade on an AP adopted by the wireless controller. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. After a scheduled upgrade, these actions can be performed. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enbales staggered reboot (one at a time) without network impact.This keyword is common to all of the above.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 23 ap-upgrade cancel-upgrade [<MAC/HOSTNAME>|all] ap-upgrade cancel-upgrade [ap4021|ap4600|ap4521|ap4522|ap4532|ap4700] all ap-upgrade cancel-upgrade on rf-domain [<DOMAIN-NAME>|all] ap-upgrade load-image [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] <IMAGE-URL> cancel-upgrade [ <MAC/HOSTNAME>|all] Cancels scheduled firmware upgrade on a specified AP or all APs adopted by the wireless controller <MAC/HOSTNAME> Specify the MAC address or hostname of the AP. all Cancels scheduled upgrade on all APs. cancel-upgrade [ap4021|ap4600|ap4511|ap4521 | ap4532|ap4700] all Cancels scheduled firmware upgrade on all adopted APs: AP4021 all Cancels scheduled upgrade on all AP4021s AP4600 all Cancels scheduled upgrade on all AP4600s AP4511 all Cancels scheduled upgrade on all AP4511s AP4521 all Cancels scheduled upgrade on all AP4521s AP4522 all Cancels scheduled upgrade on all AP4522s AP4532 all Cancels scheduled upgrade on all AP4532s AP4700 all Cancels scheduled upgrade on all AP4700s cancel-upgrade on rf-domain [<RF-DOMAIN-NAME>|all] Cancels scheduled firmware upgrade on a specified RF Domain or all RF Domains <RF-DOMAIN-NAME> Specify the RF Domain name. all Cancels scheduled upgrades on all RF Domains. load-image [ap4021|ap4600|ap4511|ap4521| ap4522|ap4532|ap4700] Loads AP firmware images on the wireless controller. Select the AP type and provide the location of the AP firmware image. AP4021 <IMAGE-URL> Loads AP4021 firmware image AP4600 <IMAGE-URL> Loads AP4600 firmware image AP4511 <IMAGE-URL> Loads AP4511 firmware image AP4521 <IMAGE-URL> Loads AP4521 firmware image AP4522 <IMAGE-URL> Loads AP4522 firmware image AP4532 <IMAGE-URL> Loads AP4532 firmware image AP4700 <IMAGE-URL> Loads AP4700 firmware image <IMAGE-URL> Specify the AP firmware image location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>:<passwd>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 24 ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-reboot {staggered-reboot}|reboot-time <TIME>} ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-via-rf-domain {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered- reboot)} rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s no-reboot {staggered-reboot} no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> {staggered- reboot} Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enbales staggered reboot (one at a time) without network impact.This keyword is common to all of the above. rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s no-via-rf-domain Upgrades APs from the adopted device. no-reboot {staggered-reboot} no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> {staggered- reboot} Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 25 ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {upgrade-time <TIME> {no-reboot|reboot-time <TIME>}}{(staggered-reboot)} Example wm3700-37FABE>ap-upgrade ap4021 all -------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE -------------------------------------------------------------------------- 00-15-70-37-FA-BE Fail Could not find any matching APs -------------------------------------------------------------------------- wm3700-37FABE> wm3700-37FABE>ap-upgrade default/ap no-reboot -------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE -------------------------------------------------------------------------- 00-15-70-37-FA-BE Success Queued 0 APs to upgrade -------------------------------------------------------------------------- upgrade-time <TIME> {no- reboot|reboot-time <TIME>} Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enbales staggered reboot (one at a time) without network impact.This keyword is common to all of the above. rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s upgrade <TIME> Schedules AP firmware upgrade. <TIME> - Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. no-reboot {staggered-reboot} no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> {staggered- reboot} Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enbales staggered reboot (one at a time) without network impact.This keyword is common to all of the above.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 26 captive-portal-page-upload User Exec Commands Uploads the captive portal advanced pages. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax captive-portal-page-upload [<CAPTIVE-PORTAL-NAME>|cancel-upload|load-file] captive-portal-page-upload <CAPTIVE-PORTAL-NAME> [<MAC/HOSTNAME>|all|rf- domain] captive-portal-page-upload <CAPTIVE-PORTAL-NAME> [<MAC/HOSTNAME>|all] {upload-time <TIME>} captive-portal-page-upload <CAPTIVE-PORTAL-NAME> rf-domain [<DOMAIN- NAME>|all] {no-via-rf-domain} {(upload-time <TIME>)} captive-portal-page-upload cancel-upload [<MAC/HOSTNAME>|all|on rf-domain [<DOMAIN-NAME>|all]] captive-portal-page-upload load-file <CAPTIVE-PORTAL-NAME> <URL> Parameters captive-portal-page-upload <CAPTIVE-PORTAL-NAME> [<MAC/HOSTNAME>|all] {upload-time <TIME>} captive-portal-page-upload <CAPTIVE-PORTAL-NAME> Uploads advanced pages specified by the <CAPTIVE-PORTAL-NAME> parameter. <CAPTIVE-PORTAL-NAME> Specify the captive portal name, which should already be existing and configured. <MAC/HOSTNAME> Uploads specified AP. <MAC/HOSTNAME> Specify APs MAC address or hostname. all Uploads all APs upload-time <TIME> Optional. Schedules an upload time. <TIME> Specify upload time in the MM/DD/YYYY-HH:MM or HH:MM format.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 27 captive-portal-page-upload <CAPTIVE-PORTAL-NAME> rf-domain [<DOMAIN- NAME>|all] {no-via-rf-domain} {(upload-time <TIME>)} captive-portal-page-upload cancel-upload [<MAC/HOSTNAME>|all|on rf-domain [<DOMAIN-NAME>|all] capt i ve- por t al - page- upl oad l oad- f i l e <CAPTI VE- PORTAL- NAME> <URL> captive-portal-page-upload <CAPTIVE-PORTAL-NAME> Uploads advanced pages specified by the <CAPTIVE-PORTAL-NAME> parameter. <CAPTIVE-PORTAL-NAME> Specify the captive portal name, which should already be existing and configured. rf-domain [<DOMAIN- NAME>|all] Uploads to all access points within a specified RF Domain or all RF Domains. <DOMIAN-NAME> Uploads APs within a specified RF Domain. Speficy the RF Domain name. all Uploads APs accross all RF Domains. no-via-rf-domain Optional. UPloads to APs from the adopted device. upload-time <TIME> Optional. Schedules an upload time. <TIME> Specify upload time in the MM/DD/YYYY-HH:MM or HH:MM format. captive-portal-page-upload cancel-upload Cancels a scheduled AP upload. cancel-upload [<MAC/ HOSTNAME|all|on rf- domain[DOMAIN-NAME>|all] Select one of the following options: <MAC/HOSTNAME> Cancels scheduled upload to a specified AP. Specify AP MAC address or hostname. all Cancels all scheduled AP uploads. on rf- domain Cancels all scheduled uploads within a specified RF Domain or all RF Domains. <DOMAIN-NAME> Cancels scheduled uploads within a specified RF Domain. Specify the RF Domain name. all Cancels scheduled uploads across all RF Domains. captive-portal-page-upload load file Loads captive-portal advanced pages. <CAPTIVE-PORTAL- NAME><URL> Specify the captive portal name, which should already be existing and configured. <URL> Specifiy thefile location one of the following formats: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>:<passwd>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 28 Example wm3700-37FABE>captive-portal-page-upload test 00-04-96-4A-A7-08 upload-time 07/15/2012-12:30 --------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE --------------------------------------------------------------------------- 00-15-70-37-FA-BE Fail Failed to initiate page upload --------------------------------------------------------------------------- wm3700-37FABE> wm3700-37FABE>captive-portal-page-upload cancel-upload 00-04-96-4A-A7-08 --------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE --------------------------------------------------------------------------- 00-15-70-37-FA-BE Success Cancelled upgrade of 1 APs --------------------------------------------------------------------------- wm3700-37FABE>
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 29 change-passwd User Exec Commands Changes the password of a logged user. When this command is executed without any parameters, the password can be changed interactively. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax change-passwd {<OLD-PASSWORD> <NEW-PASSWORD>} Parameters change passwd {<OLD-PASSWORD> <NEW-PASSWORD>} Usage Guidelines A password must be from 164 characters. Example wm3700-37FABE#change-passwd Enter old password: Enter new password: Password for user 'admin' changed successfully Please write this password change to memory(write memory) to be persistent. wm3700-37FABE#write memory OK wm3700-37FABE# <OLD-PASSWORD> <NEW-PASSWORD> Optional. The password can also be changed interactively. To do so, press [Enter] after the command. <OLD-PASSWORD> Specify the password that needs to be changed. <NEW-PASSWORD> Specify the new password.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 30 clear User Exec Commands Clears parameters, cache entries, table entries, and other similar entries. The clear command is available for specific commands only. The information cleared using this command varies depending on the mode where the clear command is executed. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 NOTE Refer to the interface details below when using clear. Clear command details: ge <index> WM3400 supports 5 GEs and WM3600 supports 8 GEs. me1 Available in both WM3700 and WM3600-up1- Uplink interface on WM3400. up1 Uplink interface on WM3400. Syntax clear [arp-cache|cdp|crypto|event-history|ip|lldp|rtls|spanning-tree|vrrp] clear arp-cache {on <DEVICE-NAME>} clear [cdp|lldp] neighbors {on <DEVICE-NAME>} clear crypto [ike|ipsec] sa clear crypto ike sa [<IP>|all] {on <DEVICE-NAME>} clear crypto ipsec sa {on <DEVICE-NAME>} clear event-history clear ip [dhcp|ospf] clear ip dhcp bindings [<IP>|all] {on <DEVICE-NAME>} clear ip ospf process {on <DEVICE-NAME>} clear rtls [aeroscout|ekahau]
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 31 clear rtls [aeroscout|ekahau] {<DEVICE-NAME> {on <DEVICE-OR-DOMAIN-NAME>}| on <DEVICE-OR-DOMAIN-NAME>} clear spanning-tree detected-protocols {interface|on} clear spanning-tree detected-protocols {on <DEVICE-NAME>} clear spanning-tree detected-protocols {interface [<INTERFACE>|ge <1-4> |me1|port-channel <1-2>|pppoe1|vlan <1-4094>|wwan1]} {on <DEVICE-NAME>} clear vrrp [error-stats|stats] {on <DEVICE-NAME>} Parameters clear arp-cache {on <DEVICE-NAME>} clear [cdp|lldp] neighbors {on <DEVICE-NAME>} clear crypto ike sa [<IP>|all] {on <DEVICE-NAME>} clear crypto ipsec sa {on <DEVICE_NAME>} arp-cache Clears Address Resolution Protocol (ARP) cache entries on an AP or wireless controller. This protocol matches the layer 3 IP addresses to the layer 2 MAC addresses. on <DEVICE-NAME> Optional. Clears ARP cache entries on a specified AP or wireless controller <DEVICE-NAME> Specify the name of the AP or wireless controller. cdp Clears Cisco Discovery Protocol (CDP) table entries lldp Clears Link Layer Discovery Protocol (LLDP) table entries neighbors Clears CDP or LLDP neighbor table entries based on the option selected in the preceding step on <DEVICE-NAME> Optional. Clears CDP or LLDP neighbor table entries on a specified AP or wireless controller <DEVICE-NAME> Specify the name of the AP or wireless controller. crypto Clears encryption module database ike sa [<IP>|all] Clears Internet Key Exchange (IKE) security associations (SAs). <IP> Clears IKE SAs for a certain peer. all Clears IKE SAs for all peers. on <DEVICE-NAME> Optional. Clears IKE SA entries for a specified peer (or all peers), or on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. crypto Clears encryption module database ipsec sa {on <DEVICE- NAME>} Clears Internet Protocol Security (IPSec) database security associations (SAs) on <DEVICE-NAME> Optional. Clears IPSec SA entries on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 32 clear event-history clear ip dhcp bindings [<IP>|all] {on <DEVICE-NAME>} clear ip ospf process {on <DEVICE-NAME>} clear rtls [aeroscout|ekahau] (<DEVICE-NAME> {on <DEVICE-OR-DOMAIN- NAME>}|on <device-or-domain-name>} clear spanning-tree detected-protocols {on <DEVICE-NAME>} event-history Clears event history cache entries. ip Clears a DHCP (Dynamic Host COnfiguration Protocol) servers IP address bindings entries. dhcp bindings Clears DHCP connections and server bindings. <IP> Clears specific address binding entries. Specify the DHCP servers IP address to clear binding entries. all Clears all address binding entries on all DHCP servers. on <DEVICE-NAME> Optional. Clears a specified address binding or all address bindings on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. ip ospf process Clears already enabled OSPF(open shortest path first) process and also restarts the process. on <DEVICE-NAME> Optional. Clears OSPF process on a specified AP or wireless controller. OSPF is a link-state IGP (interior gateway protocol). OSPF routes IP packets within a single routing domain (autonomous system), like an enterprise LAN. OSPF gathers link-state information from neighboring routers and constructs a network topology. The topology determines the routing table presented to the Internet layer, which makes routing decisions based solely on the destination IP address found in IP packets. <DEVICE-NAME> Specify the name of the AP or wireless controller. rtls Clears RTLS (Real Time Locaiton Service) statistics. aeroscout Clears RTLS AeroScout statistics. ekahau Clears RTLS Ekahau statistics. <DEVICE-NAME> This keyword is common to the AeroScout and Ekahau parameters. <DEVICE-NAME> Optional. Clears aeroscout or ekahau RTLS statistics on a specified AP or wireless controller. <DEVICE-OR-DOMAIN- NAME> This keyword is common to all of the above. <DEVICE-OR-DOMAIN-NAME> Optional. Clears Aeroscout or Ekahau RTLS statistics on a specified AP, wireless controller, or RF Domain. spanning-tree Clears spanning tree protocols on an interface and also restarts protocol migration. detected-protocols Restarts protocol migration on <DEVICE-NAME> Optional. Clears spanning tree protocols on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 33 clear spanning-tree detected-protocols {interface [<INTERFACE>|ge <1-4>| me1|port-channel <1-2>|pppoe1|vlan <1-4094>]|vvan1} {on <DEVICE-NAME>} cl ear vr r p [ er r or - st at s| st at s] {on <DEVICE-NAME>} Example wm3700-37FABE>clear event-history wm3700-37FABE>clear spanning-tree detected-protocols interface port-channel 1 on wm3700-37FABE wm3700-37FABE>clear ip dhcp bindings 172.16.10.9 on wm3700-37FABE wm3700-37FABE>clear spanning-tree detected-protocols interface ge 1 spanning-tree Clears spanning tree protocols on an interface and also restarts protocol migration. detected-protocols Restarts protocol migration. iinterface [<INTERFACE>| ge <1-4>|me1|port-channel <1-2>|pppoe1|vlan <1- 4094>|wwan1] Optional. Clears spanning tree protocols on different interfaces <INTERFACE> Clears detected spanning tree protocol on a specified interface. Specify the interface name. ge <1-4> Clears detected spanning tree protocol for the selected GigabitEtherenet (GE) interface. Select the GE interface index from 14. me1 Clears FastEthernet interface status (up1 - Clears the uplink interface). port-channel <1-2> Clears detected spanning tree protocol for the selected port channel interfacen. Select the port channel index from 12. ppoe1 Clears detected spanning tree protocol for PPoE (Point-to-Point Protocol over Ethernet) interface. vlan <1-4094> Clears VLAN interface information. Select an SVI (Switch Virtual Interface) VLAN ID from 14094. wwan1 Clears detected spanning tree protocol for wireless WAN interface. on <DEVICE-NAME> Optional. Clears spanning tree protocol entries on a selected AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. vrrp Clears VRRP (Virtual Router Redundancy Protocol) statistics for a device. VRRP allows a pool of routers to be advertized as a single virtual router. This virtual router is configured by hosts as their default gateway. VRRP elects a master router, from this pool, and assigns it a virtual IP address. The master router routes and forwards packets to hosts on the same subnet. When the master router fails, one of the backup routers is elected as the master and its IP address is mapped to the virtual IP address. error-stats {on <DEVICE- NAME>} Clears global error statistics on <DEVICE-NAME> Optional. Clears VRRP global error statistics on a selected AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. stats {on <DEVICE-NAME>} Clears VRRP related statistics on <DEVICE-NAME> Optional. Clears VRRP related statistics on a selected AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 34 wm3700-37FABE>clear lldp neighbors wm3700-37FABE>show cdp neighbors --------------------------------------------------------------------------- Device ID Neighbor IP Platform Local Intrfce Port ID Duplex --------------------------------------------------------------------------- WM3400-880DA7 172.16.10.8 WM3400-11110-US ge1 ge1 full WM3600-380649 192.168.0.1 WM3600 ge1 ge1 full ap4700-139B34 172.16.10.22 ap4700 ge1 ge1 full ap4700-4AA708 169.254.167.8 a4700-WW ge1 ge1 full --------------------------------------------------------------------------- wm3700-37FABE> wm3700-37FABE>clear cdp neighbors wm3700-37FABE>show cdp neighbors --------------------------------------------------------------------------- Device ID Neighbor IP Platform Local Intrfce Port ID Duplex --------------------------------------------------------------------------- --------------------------------------------------------------------------- wm3700-37FABE>
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 35 clock User Exec Commands Sets a devices system clock Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax clock set <HH:MM:SS> <1-31> <MONTH> <1993-2035> {on <DEVICE-NAME>} Parameters clock set <HH:MM:SS> <1-31> <MONTH> <1993-2035> {on <DEVICE-NAME>} Example wm3700-37FABE>clock set 14:43:20 07 May 2012 wm3700-37FABE>show clock 2012-05-07 14:43:20 UTC wm3700-37FABE> clock set Sets a devices software system clock <HH:MM:SS> Sets the current time (in military format hours, minutes and seconds) <1-31> Sets the numerical day of the month <MONTH> Sets the month of the year (Jan to Dec) <1993-2035> Sets a valid four digit year from 1993 - 2035 on <DEVICE-NAME> Optional. Sets the clock on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 36 cluster User Exec Commands Initiates cluster context. The cluster context provides centralized management to configure all cluster members from any one member. Commands executed under this context are executed on all members of the cluster. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cluster start-election Parameters cluster start-selection Example wm3700-37FABE>cluster start-election wm3700-37FABE> Related Commands start-election Starts a new cluster master election. create-cluster ???x-ref??? Creates a new cluster on the specified device. join-cluster ???x-ref??? Adds a wireless controller as a member to an existing cluster of wireless controlelrs.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 37 connect User Exec Commands Begins a console connection to a remote device using the remote devices MiNT ID or name Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax connect [mint-id <MINT-ID>|<REMOTE-DEVICE-NAME>] Parameters connect [mint-id <MINT-ID>|<REMOTE-DEVICE-NAME>] Example wm3700-37FABE>show mint lsp-db 2 LSPs in LSP-db of 01.42.14.79: LSP 01.42.14.79 at level 1, hostname "wm3700-37FABE", 1 adjacencies, seqnum 5069 LSP 01.44.54.C0 at level 1, hostname "ap4600-4454C0", 1 adjacencies, seqnum 5265 wm3700-37FABE>connect mint-id 01.44.54.C0 Entering character mode Escape character is '^]'. AP4600 release 5.4.0.0-033B ap4600-4454C0 login: mint-id <MINT-ID> Connects to the remote system using the MiNT ID <MINT-ID> Specify the remote devices MiNT ID. <REMOTE-DEVICE-NAME> Connects to the remote system using its name <REMOTE-DEVICE-NAME> Specify the remote devices name.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 38 wm3700-37FABE>show mint lsp-db 1 LSPs in LSP-db of 70.37.FA.BE: LSP 70.37.FA.BE at level 1, hostname "wm3700-37FABE", 0 adjacencies, seqnum 65562 wm3700-37FABE> wm3700-37FABE>connect wm3700-37FABE Entering character mode Escape character is ^]. wm3700-37FABE release 5.4.0.0-015D wm3700-37FABE login:
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 39 create-cluster User Exec Commands Creates a new cluster on a specified device. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax create-cluster name <CLUSTER-NAME> ip <IP> {level [1|2]) Parameters create-cluster name <CLUSTER-NAME> ip <IP> {level [1|2]) Example wm3700-37FABE>create-cluster name Cluster1 ip 172.16.10.1 level 1 ... creating cluster ... committing the changes ... saving the changes [OK] wm3700-37FABE> create-cluster Creates a cluster. name <CLUSTER-NAME> Configures the cluster name. <CLUSTER-NAME> Specify a cluster name. ip <IP> Specifies the devices IP address used for cluster creation. <IP> Specify the devices IP address in A.B.C.D. format. level [1|2] Optional. Configures the clusters routing level. 1 Configures level 1 (local) routing. 2 Configures level 2 (inter-site) routing.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 40 Related Commands create-cluster ???x-ref??? Creates a new cluster on the specified device. join-cluster ???x-ref??? Adds a wireless controller as a member to an existing cluster of wireless controlelrs.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 41 crypto User Exec Commands Enables digital certificate configuration and RSA Keypair management. Digital certificates are issued by CAs and contain user- or device-specific information, such as name, public key, IP address, serial number, company name, etc. Use this command to generate, delete, export, or import encrypted RSA Keypairs and generate CSRs (Certificate Signing Requests). This command also enables trustpoint configuration. Trustpoints contain the CAs identity and configuration parameters. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax crypto [key|pki] crypto key [export|generate|import|zeroise] crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {background|on|passphrase} crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE- NAME>}} crypto key generate rsa <RSA-KEYPAIR-NAME> <1024-2048> {on <DEVICE-NAME>} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {background|on|passphrase} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE- NAME>}} crypto key zeroise rsa <RSA-KEYPAIR-NAME> {force {on <DEVICE-NAME>}|on <DEVICE- NAME>}
TM 4000 Series Access Point CLI Reference Guide 43 cr ypt o key expor t r sa <RSA- KEYPAI R- NAME> <EXPORT- TO- URL> {passphrase <KEY- PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>}} cr ypt o key gener at e r sa <RSA- KEYPAI R- NAME> <1024- 2048> {on <DEVICE-NAME>} <EXPORT-TO-URL> Specify the RSA Keypair destination address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE- NAME>} Optional. Performs export operation in the background. Optionally specify the device (AP/wireless controller) to perform export on. on <DEVICE-NAME> Optional. Performs export operation on a specific device. on <DEVICE-NAME> Optional. Performs export operation on a specific device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. export rsa Exports an RSA Keypair to a specified destination <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <EXPORT-TO-URL> {passphrase <KEY-PASSPHRASE>} Specify the RSA Keypair destination address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file passpharse Optional. Encrypts the RSA Keypair before exporting it. <KEY-PASSPHRASE> Specify a passphrase to encrypt the RSA Keypair. on <DEVICE-NAME> Optional. Performs export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. generate rsa <RSA-KEYPAIR-NAME> <1024-2048> Generates a new RSA Keypair <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <1024-2048> Sets the size of the RSA key in bits from 10242048. The default size is 1024. on <DEVICE-NAME> Optional. Generates the new RSA Keypair on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 44 cr ypt o key i mpor t r sa <RSA- KEYPAI R- NAME> <I MPORT- FROM- URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} cr ypt o key i mpor t r sa <RSA- KEYPAI R- NAME> <I MPORT- FROM- URL> {passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>}} key Enables RSA Keypair management. Use this command to export, import, generate, or delete an RSA key. import rsa <RSA-KEYPAIR- NAME> Imports aN RSA Keypair from a specified source. <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <IMPORT-FROM-URL> Specify the RSA Keypair source address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. background {on <DEVICE-NAME>} Optional. Performs import operation in the background on <DEVICE-NAME> Optional. Performs import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete an RSA key. import rsa <RSA-KEYPAIR- NAME> Imports aN RSA Keypair from a specified source. <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <IMPORT-FROM- URL>{passphrase<KEY- PASSPHRASE>} Specify the RSA Keypair source address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file passphrase Optional. Decrypts the RSA Keypair before importing it. <KEY-PASSPHRASE> Specify the passphrase to decrypt the RSA Keypair. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 45 cr ypt o key zer oi se <RSA- KEYPAI R- NAME> {force {on <DEVICE-NAME>}|on <DEVICE- NAME>} cr ypt o pki aut hent i cat e <TRUSTPOI NT- NAME> <URL> {background {on <DEVICE-NAME>}| on <DEVICE-NAME>} cr ypt o pki expor t r equest [ gener at e- r sa- key| use- r sa- key] <RSA- KEYPAI R- NAME> aut ogen- subj ect - name [ ur l <EXPORT- TO- URL>, emai l <SEND- TO- EMAI L>, f qdn <FQDN>, i p- addr ess <I P>] key Enables RSA Keypair management. Use this command to export, import, generate, or delete an RSA key. izeroise rsa <RSA-KEYPAIR- NAME> Deletes a specified RSA Keypair. <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. NOTE: All device certificates associated with this key will also be deleted. force {on <DEVICE-NAME>} Optional. Forces deletion of all certificates associated with the specified RSA Keypair. Optionally specify a device (AP/wireless controller) on which to force certificate deletion. on <DEVICE-NAME> Optional. Deletes all certificates associated with the RSA Keypair on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI (Private Key Infrastructure) management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. authenticate <TRUSTPOINT- NAME> Authenticates a trustpoint and imports the corresponding CA certificate. <TRUSTPOINT-NAME> Specify the trustpoint name. <URL> Specify CAs location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file NOTE: The CA certificate is imported from the specified location. background {on <DEVICE-NAME>} Optional. Performs authentication in the background. Optionally specify a device (AP/wireless controller) on which to perform authentication. on <DEVICE-NAME> Optional. Performs authentication on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI (Private Key Infrastructure) management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. export request Exports CSR (Certificate Signing Request) to the CA for digital identity certificate. The CSR contains applicants details and RSA Keypairs public key.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 46 crypto pki export request [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> subject-name <COUNTRY> <STATE> <CITY> <ORGANIZATION> <ORGANIZATION-UNIT> [url <EXPORT-TO-URL>, email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>] [generate-rsa-key|use-rsa- key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair or uses an existing RSA Keypair generate-rsa-key Generates a new RSA Keypair for digital authentication use-rsa-key Uses an existing RSA Keypair for digital authentication <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. autogen-subject-name Auto generates subject name from configuration parameters. The subject name identifies the certificate. url <EXPORT-TO-URL> {background {on <DEVICE- NAME}|on <DEVICE- NAME>} Specify CAs location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file NOTE: The CSR is exported to the specified location. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. email <SEND-TO-EMAIL> Exports theCSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the CAs e-mail address. fqdn <FQDN> Exports CSR to a specified FQDN (Fully Qualified Domain Name). <FQDN> Specify the CAs FQDN. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. export request Exports the CSR to the CA for a digital identity certificate.The CSR contains the applicants details and the RSA Keypairs public key. [generate-rsa-key| use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair or uses an existing RSA Keypair generate-rsa-key Generates a new RSA Keypair for digital authentication use-rsa-key Uses an existing RSA Keypair for digital authentication <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. subject-name <COMMON-NAME> Specifies the subject name to identify the certificate. <COMMON-NAME> Specify the common name used with the CA certificate. The name should enable you to identify the certificate easily (264 characters in length). <COUNTRY> Sets the deployment country name (2 character ISO code) <STATE> Sets the state name (2 to 64 characters) <CITY> Sets the city name (2 to 64 characters) <ORGANIZATION> Sets the organization name (2 to 64 characters) <ORGANIZATION-UNIT> Sets the organization unit (2 to 64 characters)
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 47 crypto pki export trustpoint <TRUSTPOINT-NAME> <EXPORT-TO-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>|passphrase <KEY-PASSPHRASE> background {on <DEVICE-NAME>}|on <DEVICE-NAME>}} url <EXPORT-TO-URL> {background {on <DEVICE- NAME}|on <DEVICE-NAME>} Specify the CAs location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file NOTE: THe CSR is exported to the specified location. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specific device. <DEVICE-NAME> Specify the name of the AP or wireless controller. email <SEND-TO-EMAIL> Exports the CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the CAs e-mail address. fqdn <FQDN> Exports CSR to a specified FQDN. <FDQN> Specify the CAs FQDN. ip address <IP> Exports CSR to a specified device or system <IP> Specify the CAs IP address. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. export trustpoint <TRUSTPOINT-NAME> Exports a trustpoint along with a CA certificate, CRL (Certificate Revocation List), server certificate, and private key. <TRUSTPOINT-NAME> Specify the trustpoint name. <EXPORT-TO-URL> Specify the destination address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file usb2:/path/file background {on <DEVICE-NAME>} Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 48 crypto pki generate self-signed <TRUSTPOINT-NAME> [generate-rsa-key|use- rsa-key] <RSA-KEYPAIR-NAME> autogen-subject-name [email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>, on <DEVICE-NAME>] crypto pki generate self-signed <TRUSTPOINT-NAME> [generate-rsa-key|use- rsa-key] <RSA-KEYPAIR-NAME> subject-name <COMMON-NAME> <COUNTRY> <STATE> <CITY> <ORGANIZATION> <ORGANIZATION-UNIT> [email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>, on <DEVICE-NAME>] passphrase <KEY-PASSPHRASE> {background {on <DEVICE- NAME>}| on <DEVICE-NAME>} Optional. Encrypts the key with a passphrase before exporting it. <KEY-PASSPHRASE> Specify the passphrase. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. generate Generates a CA certificate and a trustpoint. self-signed <TRUSTPOINT-NAME> Generates a self-signed CA certificate and a trustpoint. <TRUSTPOINT-NAME> Specify a name for the certificate and its trustpoint. [generate-rsa-key| use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair, or uses an existing RSA Keypair generate-rsa-key Generates a new RSA Keypair for digital authentication use-rsa-key Uses an existing RSA Keypair for digital authentication <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. autogen-subject-name Auto-generates the subject name from the configuration parameters. The subject name helps to identify the certificate. email <SEND-TO-EMAIL> Exports the CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the CAs e-mail address. fqdn <FQDN> Exports the CSR to a specified FQDN. <FQDN> Specify the CAs FQDN. ip-address <IP> Exports the CSR to a specified device or system. <IP> Specify the CAs IP address. on <DEVICE-NAME> Exports the CSR on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. generate Generates a CA certificate and a trustpoint. self-signed <TRUSTPOINT-NAME> Generates a self-signed CA certificate and a trustpoint. <TRUSTPOINT-NAME> Specify a name for the certificate and its trustpoint. [generate-rsa-key| use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair, or uses an existing RSA Keypair. generate-rsa-key Generates a new RSA Keypair for digital authentication. use-rsa-key Uses an existing RSA Keypair for digital authentication. <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 49 crypto pki import [certificate|crl] <TRUSTPOINT-NAME> <IMPORT-FROM-URL> {background {on <DEVICE-NAME>}|on <DEVICE--NAME>} subject-name <COMMON-NAME> Specify a subject name to identify the certificate. <COMMON-NAME> Specify the common name used with the CA certificate. The name should enable you to identify the certificate easily. <COUNTRY> Sets the deployment country name (2 character ISO code). <STATE> Sets the state name (2 to 64 characters). <CITY> Sets the city name (2 to 64 characters). <ORGANIZATION> Sets the organization name (2 to 64 characters). <ORGANIZATION-UNIT> Sets the organization unit (2 to 64 characters). email <SEND-TO-EMAIL> Exports the CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the CAs e-mail address. fqdn <FQDN> Exports the CSR to the CA by providing the FQDN of the CA. <FQDN> Specify the CAs FQDN. ip address <IP> Exports the CSR to a specified device or system. <IP> Specify the CAs IP address. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. import Imports certificates, a CRL, or a trustpoint to the selected device. [certificate|crl] <TRUSTPOINT-NAME> Imports a signed server certificate or CRL. certificate Imports signed server certificate crl Imports CRL <TRUSTPOINT-NAME> Specify the trustpoint name (should be authenticated). <IMPORT-FROM-URL> Specify the signed server certificate or CRL source address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE-NAME>} Optional. Performs the import operation in the background. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 50 cr ypt o pki i mpor t t r ust poi nt <TRUSTPOI NT- NAME> <I MPORT- FROM- URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>|passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>}} crypto pki zeroise trustpoint <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. import Imports certificates, a CRL, or a trustpoint to the selected device. trustpoint <TRUSTPOINT-NAME> Imports a trustpoint and its associate CA certificate, server certificate, and a private key. <TRUSTPOINT-NAME> Specify the trustpoint name (should be authenticated). <IMPORT-FROM-URL> Specify the trustpoint source address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE-NAME>} Optional. Performs the import operation in the background. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}| on <DEVICE-NAME>} Optional. Encrypts trustpoint with a passphrase before importing it. <KEY-PASSPHRASE> Specify a passphrase. background Optional. Imports the encrypted trustpoint in the background. on <DEVICE-NAME> Optional. Imports the encrypted trustpoint on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. zeroise <TRUSTPOINT-NAME> Deletes a trustpoint and its associated CA certificate, server certificate, and private key <TRUSTPOINT-NAME> Specify the trustpoint name (should be authenticated). del-key {on <DEVICE-NAME>} Optional. Deletes the private key associated with the server certificate on <DEVICE-NAME> Optional. Deletes private key on a specific device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Deletes the trustpoint on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 51 Example wm3700-37FABE>crypto key generate rsa key 1025 RSA Keypair successfully generated wm3700-37FABE> wm3700-37FABE>crypto key import rsa en123 url passphrase word background on wm3700-37FABE RSA key import operation is started in background wm3700-37FABE> wm3700-37FABE>crypto pki generate self-signed word generate-rsa-key word autogen-subject-name fqdn word Successfully generated self-CA certificate wm3700-37FABE> wm3700-37FABE>crypto pki zeroize trustpoint word del-key on wm3700-37FABE Successfully removed the trustpoint and associated certificates %Warning: Applications associated with the trustpoint will start using default-trustpoint wm3700-37FABE> wm3700-37FABE>crypto pki authenticate word url background on wm3700-37FABE Import of CA certificate started in background wm3700-37FABE> wm3700-37FABE>crypto pki import trustpoint word url passphrase word on wm3700-37FABE Import operaton started in background wm3700-37FABE> Related Commands no Removes server certificates, trustpoints, and their associated certificates
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 52 disable User Exec Commands Turns off (disables) the privileged mode command set. This command returns to the User Executable mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax disable Parameters None Example wm3700-37FABE#disable wm3700-37FABE>
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 53 enable User Exec Commands Turns on (enables) the privileged mode command set. This command does not do anything in the Privilege Executable mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax enable Parameters None Example wm3700-37FABE>enable wm3700-37FABE#
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 54 join-cluster User Exec Commands Adds a wireless controller as a member to an existing cluster of wireless controllers. Use this command to add a new wireless controller to an existing cluster. Before adding the wireless controller, assign a static IP address. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax join-cluster <IP> user <USERNAME> password <WORD> {level|mode} join-cluster <IP> user <USERNAME> password <WORD> {level [1|2]|mode [active|standby]} Parameters j oi n- cl ust er <I P> user <USERNAME> passwor d <WORD> {level [1|2]|mode [active|standby]} join-cluster Adds a new wireless controller ot an existing cluster. <IP> Specify the IP address of the cluster member. user <USERNAME> Specify a user account with superuser privileges on the new cluster member. password <WORD> Specify the password for the account specified in the user parameter. level [1|2] Optional. Configures the routing level. 1 Configures level 1 routing. 2 Configures level 2 routing. mode [active|standby] Optional. Configures the cluster mode. active Configures this cluster as active. standby Configures this cluster to be on standby mode.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 55 Usage Guidelines To add a wireless controller to an existing cluster: Configure a static IP address on the wireless controller. Provide username and password for superuser, network admin, system admin, or operator accounts. Once a wireless controller is added to the cluster, execute a manual write memory command. Without this command, the configuration will not persist across reboots. Example wm3700-37FABE>join-cluster 172.16.10.10 user admin password extreme Joining cluster at 172.16.10.10... Done Please execute write memory to save cluster configuration wm3700-37FABE# Related Commands cluster Initiates cluster context. The cluster context enables centralized management and configuration of all cluster members from any one member. create-cluster Creates a new cluster on a specified device.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 56 l2tpv3 User Exec Commands Establishes or brings down a L2TPV3 (Layer 2 Tunnel Protocol Version 3) tunnel. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax l2tpv3 tunnel [<TUNNEL-NAME>|all] l2tpv3 tunnel <TUNNEL-NAME> [down|session|up] l2tpv3 tunnel <TUNNEL-NAME> [down|up] {on <DEVICE-NAME>} l2tpv3 tunnel <TUNNEL-NAME> session <SESSION-NAME> [down|up] {on <DEVICE- NAME>} l2tpv3 tunnel all [down|up] {on <DEVICE-NAME>} Parameters l 2t pv3 t unnel <TUNNEL- NAME> [ down| up] {on <DEVICE-NAME>} l 2t pv3 t unnel <TUNNEL- NAME> sessi on <SESSI ON- NAME> [ down| up] {on <DEVICE-NAME>} l2tpv3 tunnel Establishes or brings down L2TPV3 tunnel. <TUNNEL-NAME> [down|up] Specifies the tunnel name to establish or bring down. down Brings down the specified tunnel. up Establishes the specified tunnel. on <DEVICE-NAME> Optional. Establishes or brings down a tunnel on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. l2tpv3 tunnel Establishes or brings down L2TPV3 tunnel. <TUNNEL-NAME> [session <SESSION-NAME>] [down|up] Establishes or brings down a specified session inside an L2TPV3 tunnel. <TUNNEL-NAME> Specify the tunnel name. session <SESSION-NAME> Specify the session name. down Brings down the specified session. up Establishes the specified session.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 57 l 2t pv3 t unnel al l [ down| up] {on <DEVICE-NAME>} Example wm3700-37FABE>l2tpv3 tunnel Tunnel1 sesion Tunnel1Session1 up on wm3700- 37FABE NOTE IFor more information on the L2TPV3 tunnel configuration mode and commands, see Chapter 26 on page 1121. on <DEVICE-NAME> Optional. Establishes or brings down a tunnel on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. l2tpv3 tunnel Establishes or brings down L2TPV3 tunnel. all [down|up] Establishes or brings down all L2TPV3 tunnels. down Brings down all tunnels. up Establishes all tunnels. on <DEVICE-NAME> Optional. Establishes or brings down all tunnels on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 58 logging User Exec Commands Modifies message logging settings Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax logging monitor {<0-7>|alerts|critical|debugging|emergencies|errors| informational|warnings|notifications} Parameters logging monitor {<0-7>|alerts|critical|debugging|emergencies|errors| informational|warnings|notifications} Example wm3700-37FABE>logging monitor warnings wm3700-37FABE>show logging Logging module: enabled Aggregation time: disabled Console logging: level warnings monitor Sets the terminal lines logging levels. The logging severity levels can be set from 07. The system configures default settings, if no logging severity level is specified. <07> Optional. Specify the logging severity level from 07. The various levels and their implications are as follows: alerts Optional. Immediate action needed (severity=1). critical Optional. Critical conditions (severity=2). debugging Optional. Debugging messages (severity=7). emergencies Optional. System is unusable (severity=0). errors Optional. Error conditions (severity=3). informational Optional.Informational messages (severity=6). notifications Optional. Normal but significant conditions (severity=5). warnings Optional. Warning conditions (severity=4).
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 59 Monitor logging: level warnings Buffered logging: level warnings Syslog logging: level warnings Facility: local7 Log Buffer (18611 bytes): Mar 14 14:52:22 2012: %AUTHPRIV-4-WARNING: pluto[1304]: inserting event EVENT_REINIT_SECRET, timeout in 3600 seconds Mar 14 14:51:29 2012: %CERTMGR-4-CERT_EXPIRY: server certificate for trustpoint mint_security_trustpoint Certificate has expired. Valid until: Tue Apr 26 15:00:41 2011 UTC, current time: Wed Mar 14 14:51:29 2012 UTC Mar 14 14:51:29 2012: %CERTMGR-4-CERT_EXPIRY: ca certificate for trustpoint mint_security_trustpoint Certificate has expired. Valid until: Tue Apr 26 15:00:39 2011 UTC, current time: Wed Mar 14 14:51:29 2012 UTC --More-- Related Commands no Resets the terminal lines logging levels
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 60 exit User Exec Commands Ends the current CLI session and closes the session window. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax exit Parameters None Example wm3700-37FABE>exit
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 61 mint User Exec Commands Uses MiNT protocol to perform a ping and a traceroute to a remote device. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mint [ping|traceroute] mint ping <MINT-ID> {count [<1-10000>]|size [<1-64000>]|timeout [<1-10>]} mint traceroute <MINT-ID> {(destination-port [<1-65535>]|max-hops <1-255>| source-port <1-65535>|timeout <1-255>)} Parameters mi nt pi ng <MI NT- I D> {(count <1-10000>|size <1-64000>|timeout <1-10>) mi nt t r acer out e <MI NT- I D> {destination-port <1-65535>|max-hops <1-255>| source-port <1-65535>|timseout <1-255>} ping <MINT-ID> Sends a MiNT echo message to a MiNT destination. <MINT-ID> Specify the MiNT ID of the destination device. count <1-10000> Optional. Sets the number of times to ping the MiNT destination. <1-10000> Specify a value from 110000. The default is 3 times. size <1-64000> Optional. Sets the MiNT payload size in bytes. <1-64000> Specify a value from 1640000. The default is 64 bytes. timeout <1-10> Optional. Sets a response time in seconds. <1-10> Specify a value from 110. The default is 1 second. traceroute <MINT-ID> Prints the route packets trace to a device. <MINT-ID> Specify the MiNT ID of the destination device. destination-port <1-65535> Optional. Sets the ECMP (Equal-cost Multi-path) routing destination port. <1-65535> Specify a value from 165535. The default port is 45.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 62 Example wm3700-37FABE>mint ping 70.37.FA.BF count 20 size 128 MiNT ping 70.37.FA.BF with 128 bytes of data. Response from 70.37.FA.BF: id=1 time=0.292 ms Response from 70.37.FA.BF: id=2 time=0.206 ms Response from 70.37.FA.BF: id=3 time=0.184 ms Response from 70.37.FA.BF: id=4 time=0.160 ms Response from 70.37.FA.BF: id=5 time=0.138 ms Response from 70.37.FA.BF: id=6 time=0.161 ms Response from 70.37.FA.BF: id=7 time=0.174 ms Response from 70.37.FA.BF: id=8 time=0.207 ms Response from 70.37.FA.BF: id=9 time=0.157 ms Response from 70.37.FA.BF: id=10 time=0.153 ms Response from 70.37.FA.BF: id=11 time=0.159 ms Response from 70.37.FA.BF: id=12 time=0.173 ms Response from 70.37.FA.BF: id=13 time=0.156 ms Response from 70.37.FA.BF: id=14 time=0.209 ms Response from 70.37.FA.BF: id=15 time=0.147 ms Response from 70.37.FA.BF: id=16 time=0.203 ms Response from 70.37.FA.BF: id=17 time=0.148 ms Response from 70.37.FA.BF: id=18 time=0.169 ms Response from 70.37.FA.BF: id=19 time=0.164 ms Response from 70.37.FA.BF: id=20 time=0.177 ms --- 70.37.FA.BF ping statistics --- 20 packets transmitted, 20 packets received, 0% packet loss round-trip min/avg/max = 0.138/0.177/0.292 ms max-hops <1-255> Optional. Sets the maximum number of hops a traceroute packet traverses in the forward direction. <1-255> Specify a value from 1255. The default is 30. source-port <1-65535> Optional. Sets the ECMP source port. <1-65535> Specify a value from 165535. The default port is 45. timeout <1-255> Optional. Sets the minimum response time period. <1-65535> Specify a value from 1255. The default is 30 seconds.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 63 no User Exec Commands Use the no command to revert a command or to set parameters to their default. This command is useful to turn off an enabled feature or set default values for a parameter. NOTE The commands have their own set of parameters that can be reset. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [adoption|captive- portal|crypto|debug|logging|page|service|terminal|wireless] no adoption {on <DEVICE-OR-DOMAIN-NAME>} no captive-portal client [captive-portal <CAPTIVE-PORTAL-NAME>|mac <MAC>] {on <DEVICE-OR-DOMAIN-NAME>} no crypto pki [server|trustpoint] no crypto pki [server|trustpoint] <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} no logging monitor no page no service [cli-tables-expand|locator] no service [cli-tables-expand <LINE>|locator {on <DEVICE-NAME>}] no service locator {on <DEVICE-NAME>} no terminal [length|width] no wireless client [all|<MAC>] no wireless client all {filter|on}
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 64 no wireless client all {filter[vlan <WLAN-NAME>]} no wireless client all {on <DEVICE-OR-DOMAIN-NAME> {filter [vlan [<WLAN- NAME>]} no wireless client mac<MAC> {on <DEVICE-OR-DOMAIN-NAME>} Parameters no adoption {on <DEVICE-OR-DOMAIN-NAME>} no captive-portal client [captive-portal <CAPTIVE-PORTAL-NAME>|mac <MAC>] {on <DEVICE-OR-DOMAIN-NAME>} no crypto pki [server|trustpoint] <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} no logging monitor no page no adoption {on <DEVICE-OR-DOMAIN- NAME>} Resets the adoption status of a specified device or all devices adopted by a device <DEVICE-OR-DOMAIN-NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. no captive-portal client Disconnects captive portal clients from the network. captive-portal <CAPTIVE-PORTAL-NAME> Disconnects captive portal clients. <CAPTIVE-PORTAL-NAME> Specify the captive portal name. mac <MAC> Disconnects a specified client by its MAC addres. <MAC> Specify the MAC address of the client. on <DEVICE-OR-DOMAIN- NAME> Optional. Disconnects clients on a specified device or RF Domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. no crypto pki Deletes all PKI authentications. [server|trustpoint] <TRUSTPOINT-NAME> Deletes PKI authentications, such as server certificates and trustpoints. server Deletes server certificates. trustpoint Deletes a trustpoint and its associated certificates. The following is common to the server and trustpoint parameters: <TURSTPOINT-NAME> Deletes a trustpoint or its server certificate. Specify the trustpoint name. del-key {on <DEVICE-NAME>} Optional. Deletes the private key associated with a server certificate or trustpoint. The operation will fail if the private key is in use by other trustpoints. on <DEVICE-NAME> Optional. Deletes the private key on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. no logging monitor Resets terminal lines message logging levels no page Resets wireless controller paging function to its default. Disabling the page command displays the CLI command output at once, instead of page by page.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 65 no service [cli-tables-expand <LINE>|locator {on <DEVICE-NAME>}] no terminal [length|width] no wireless client all {filter [vlan [<WLAN-NAME>]]} no wireless client all {on <DEVICE-OR-DOMAIN-NAME> {filter [vlan <WLAN- NAME>]} no wireless client mac <MAC> {on <DEVICE-OR-DOMAIN-NAME>} Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. no service Disables LEDs a specified device in the WLAN. It also resets the CLI table expand and MiNT protocol configurations. cli-tables-expand <LINE> Resets the expand configuration of the CLI table, so that the table does not expand in the drop-down format. locator {on <DEVICE-NAME>} Disables LEDs on a specified device. on <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller. no terminal [length|width] Resets the width of the terminal window or the number of lines displayed within the terminal window. length Resets the number of lines displayed on the terminal window to its default. width Resets the width of the terminal window to its default. no wireless client all Disassociates all clients on a specified device or domain. filter [wlan <WLAN-NAME>] Optional. Specifies additional client selection filter. wlan Optional. Filters clients based on the WLAN. <WLAN-NAME> Specify the WLAN name. no wireless client all on <DEVICE-OR-DOMAIN- NAME> Disassociates all wireless clients on a specified device or domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. filter wlan <WLAN-NAME> The following are optional filter parameters: filter Optional. Specifies additional client selection filter. wlan Filters clients based on the WLAN. <WLAN-NAME> Specify the WLAN name. no wireless client mac <MAC> Disassociates a single wireless client on a specified device or domain. mac <MAC> Specify the MAC address of the wireless client in the AA-BB- CC-DD-EE-FF format. on <DEVICE-OR-DOMAIN- NAME Optional. Specify the name of the AP, wireless controller, or RF Domain.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 66 Example wm3700-37FABE>no adoption wm3700-37FABE> wm3700-37FABE>no page wm3700-37FABE> wm3700-37FABE>no service cli-tables-expand line wm3700-37FABE> Related Commands auto-provisioning-policy Resets the adoption state of a device and all devices adopted to it captive portal Manages captive portal clients crypto Enables digital certificate configuration and RSA Keypair management. mint Modifies message logging settings page Resets the wireless controller paging function to its default service Performs different functions depending on the parameter passed terminal Sets the length or the number of lines displayed within the terminal window wireless-client Manages wireless clients
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 67 page User Exec Commands Toggles wireless controller paging. Enabling this command displays the CLI command output page by page, instead of running the entire output at once. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax page Parameters None Example wm3700-37FABE>page wm3700-37FABE> Related Commands no Disables wireless controller paging
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 68 ping User Exec Commands Sends Internet Controller Message Protocol (ICMP) echo messages to a user-specified location Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ping [<IP>/<HOSTNAME>] {count <1-10000>|dont-fragment|size <1-64000>} Parameters ping [<IP>/<HOSTNAME>] {count <1-10000>|dont-fragment|size <1-64000>} Example wm3700-37FABE>ping 172.16.10.3 PING 172.16.10.3 (172.16.10.3): 100 data bytes 108 bytes from 172.16.10.4: seq=0 ttl=64 time=0.851 ms 108 bytes from 172.16.10.4: seq=1 ttl=64 time=0.430 ms 108 bytes from 172.16.10.4: seq=2 ttl=64 time=0.509 ms 108 bytes from 172.16.10.4: seq=3 ttl=64 time=0.507 ms 108 bytes from 172.16.10.4: seq=4 ttl=64 time=0.407 ms 108 bytes from 172.16.10.4: seq=5 ttl=64 time=0.402 ms --- 172.16.10.3 ping statistics --- <IP>/<HOSTNAME> Optional. Specify the destination IP address or hostname. When entered without any parameters, this command prompts for an IP address or a hostname. count <1-10000> Optional. Sets the number of pints to a specified destination. <1-10000> Specify a value from 110000. The default is 5. dont-fragment Sets the dont fragment bit in the ping packet. Packets with the dont-fragment bit specified, are not fragmented. When a packet, with the dont-fragment bit specified, exceeds the specified MTU (maximum transmission unit) value, an error message is sent from the device trying to fragment it. size <1-64000> Optional. Sets the size of the ping payload in bytes. <1-64000> Specify the ping payload size from 164000. The default is 100 bytes.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 69 6 packets transmitted, 6 packets received, 0% packet loss round-trip min/avg/max = 0.402/0.517/0.851 ms wm3700-37FABE>
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 70 ssh User Exec Commands Opens a Secure Shell (SSH) connection between two network devices. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ssh <IP/HOSTNAME> <USER-NAME> Parameters ssh <IP/HOSTNAME> <USER-NAME> Example wm3700-37FABE>ssh 172.16.10.4 admin The authenticity of host '172.16.10.4 (172.16.10.4)' can't be established. RSA key fingerprint is 82:b7:27:86:de:08:e8:53:9f:d6:a3:88:aa:1f:e8:ff. Are you sure you want to continue connecting (yes/no)? <IP>/<HOSTNAME> Specify the IP address or hostname of the remote system. <USERNAME> Specify the name of the user requesting SSH connection with the remote system.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 71 telnet User Exec Commands Opens a Telnet session between two network devices Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax telnet <IP/HOSTNAME> {<TCP-PORT>} Parameters telnet <IP/HOSTNAME> {<TCP-PORT>} Example wm3700-37FABE>telnet 172.16.10.4 Entering character mode Escape character is '^]'. wm3700-37FABE release 5.4.0.0-032R wm3700-37FABE login: admin Password: wm3700-37FABE> <IP>/<HOSTNAME> Configures the IP address or hostname of the desintaiton remote system. The Telnet session is established between the connecting system and the remote system. <IP/HOSTNAME> Specify the IP address or hostname of the remote system. <TCP-PORT> Optional. Specify the TCP (Transmission Control Protocol ) port number.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 72 terminal User Exec Commands Sets the length or the number of lines displayed within the terminal window Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax terminal [length|width] <0-512> Parameters terminal [length|width] <0-512> Example wm3700-37FABE>terminal length 150 wm3700-37FABE> wm3700-37FABE>terminal width 215 wm3700-37FABE> wm3700-37FABE>show terminal Terminal Type: xterm Length: 150 Width: 215 wm3700-37FABE> Related Commands length <0-512> Sets the number of lines displayed on a terminal window. <0-512> Specify a value from 0512. width <0-512> Sets the width or number of characters displayed on a terminal window. <0-512> Specify a value from 0512. no Resets the width of the terminal window or the number of lines displayed within the terminal window
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 73 time-it User Exec Commands Verifies the time taken by a particular command between request and response Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax time-it <COMMAND> Parameters time-it <COMMAND> Example wm3700-37FABE>time-it enable That took 0.00 seconds.. wm3700-37FABE# time-it <COMMAND> Verifies the time taken by a particular command to execute and provide a result <COMMAND> Specify the command.
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 74 traceroute User Exec Commands Traces the route to a defined destination Use --help or -h to display a complete list of parameters for the traceroute command Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax traceroute <LINE> Parameters traceroute <LINE> Example wm3700-37FABE>traceroute --help BusyBox v1.14.1 () multi-call binary Usage: traceroute [-FIldnrv] [-f 1st_ttl] [-m max_ttl] [-p port#] [-q nqueries] [-s src_addr] [-t tos] [-w wait] [-g gateway] [-i iface] [-z pausemsecs] HOST [data size] Trace the route to HOST Options: -F Set the don't fragment bit -I Use ICMP ECHO instead of UDP datagrams -l Display the ttl value of the returned packet -d Set SO_DEBUG options to socket -n Print hop addresses numerically rather than symbolically traceroute <LINE> Traces the route to a destination IP address or hostname <LINE> Specify a traceroute argument. For example, service traceroute-h.
User Exec Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 75 -r Bypass the normal routing tables and send directly to a host -v Verbose -m max_ttl Max time-to-live (max number of hops) -p port# Base UDP port number used in probes (default is 33434) -q nqueries Number of probes per 'ttl' (default 3) -s src_addr IP address to use as the source address -t tos Type-of-service in probe packets (default 0) -w wait Time in seconds to wait for a response (default 3 sec) -g Loose source route gateway (8 max) wm3700-37FABE>traceroute 172.16.10.1 traceroute to 172.16.10.1 (172.16.10.1), 30 hops max, 38 byte packets 1 172.16.10.1 (172.16.10.1) 0.423ms !H 0.145 ms !H 0.225 ms !H wm3700-37FABE>
Chapter 3: User Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 76 watch User Exec Commands Repeats the specified CLI command at periodic intervals Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax watch <1-3600> <LINE> Parameters watch <1-3600> <LINE> Example wm3700-37FABE>watch 45 page wm3700-37FABE> wm3700-37FABE>watch 45 ping 172.16.10.2 PING 172.16.10.2 (172.16.10.2): 100 data bytes 108 bytes from 172.16.10.2: seq=0 ttl=64 time=0.725 ms 108 bytes from 172.16.10.2: seq=1 ttl=64 time=0.464 ms 108 bytes from 172.16.10.2: seq=2 ttl=64 time=0.458 ms 108 bytes from 172.16.10.2: seq=3 ttl=64 time=0.378 ms 108 bytes from 172.16.10.2: seq=4 ttl=64 time=0.364 ms --- 172.16.10.2 ping statistics --- 5 packets transmitted, 5 packets received, 0% packet loss round-trip min/avg/max = 0.364/0.477/0.725 ms wm3700-37FABE> watch Repeats a CLI command at a specified interval. <1-3600> Select an interval from 13600 seconds. Pressing CTRL-Z halts execution of the command. <LINE> Specify the CLI command.
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 77 C H A P T E R 4 Privileged Exec Mode Commands Most PRIV EXEC commands set operating parameters. Privileged-level access should be password protected to prevent unauthorized use. The PRIV EXEC command set includes commands contained within the USER EXEC mode. The PRIV EXEC mode also provides access to configuration modes, and includes advanced testing commands. The PRIV EXEC mode prompt consists of the hostname of the device followed by a pound sign (#). To access the PRIV EXEC mode, enter the following at the prompt: wm3400-37FABE>enable wm3400-37FABE# The PRIV EXEC mode is often referred to as the enable mode, because the enable command is used to enter the mode. There is no provision to configure a password to get direct access to PRIV EXEC (enable) mode. wm3400-37FABE#? Priv Exec commands: ap-upgrade AP firmware upgrade archive Manage archive files boot Boot commands captive-portal-page-upload Captive portal advanced page upload cd Change current directory change-passwd Change password clear Clear clock Configure software system clock cluster Cluster commands commit Commit all changes made in this session configure Enter configuration mode connect Open a console connection to a remote device copy Copy from one file to another create-cluster Create a cluster crypto Encryption related commands debug Debugging functions delete Deletes specified file from the system. diff Display differences between two files dir List files on a filesystem disable Turn off privileged mode command edit Edit a text file
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 78 enable Turn on privileged mode command erase Erase a filesystem format Format file system halt Halt the system help Description of the interactive help system join-cluster Join the cluster l2tpv3 L2tpv3 protocol logging Modify message logging facilities mint MiNT protocol mkdir Create a directory more Display the contents of a file no Negate a command or set its defaults page Toggle paging ping Send ICMP echo messages pwd Display current directory re-elect Perform re-election reload Halt and perform a warm reboot remote-debug Troubleshoot remote system(s) rename Rename a file revert Revert changes rmdir Delete a directory self Config context of the device currently logged into service Service Commands show Show running system information ssh Open an ssh connection telnet Open a telnet connection terminal Set terminal line parameters time-it Check how long a particular command took between request and completion of response traceroute Trace route to destination upgrade Upgrade software image upgrade-abort Abort an ongoing upgrade watch Repeat the specific CLI command at a periodic interval write Write running configuration to memory or terminal clrscr Clears the display screen exit Exit from the CLI wm3400-37FABE# Privileged Exec Mode Commands Table 3.1 summarizes the PRIV EXEC Mode commands:. Command Description Reference ap-upgrade Enables an automatic firmware upgrade on an adopted AP page 4-81 archive Manages file archive operations page 4-88 boot Specifies the image used after reboot page 4-90
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 79 captive-portal- page-upload Uploads captive portal advanced pages page 4-91 captive-portal- page-upload Changes the current directory page 4-91 change-passwd Changes the password of a logged user page 4-95 clear Clears parameters, cache entries, table entries, and other similar entries page 4-96 clock Configures the system clock page 4-101 cluster Initiates a cluster context page 4-102 configure Enters the configuration mode page 4-103 connect Begins a console connection to a remote device page 4-104 copy Copies a file from any location to the wireless controller page 4-106 create-cluster Creates a new cluster on a specified device page 4-107 crypto Enables encryption page 4-109 delete Deletes a specified file from the system page 4-119 edit Displays the differences between two files page 4-126 dir Displays the list of files on a file system page 4-110 disable Disables the privileged mode command set page 4-125 edit Edits a text file page 4-126 enable Turns on (enables) the privileged mode commands set page 4-128 erase Erases a file system page 4-129 exit Ends the current CLI session and closes the session window page 4-130 format Formats the file system page 4-131 halt Stops the wireless controller page 4-132 join-cluster Adds a wireless controller, as cluster member, to an existing cluster of wireless controllers page 4-133 l2tpv3 Establishes or brings down a L2TPV3 tunnel page 4-135 logging Modifies message logging parameters page 4-137 more Configures MiNT protocols page 4-143 mkdir Creates a new directory in the file system page 4-141 more Displays the contents of a file page 4-143 no Reverts a command or sets values to their default settings page 4-145 page Toggles wireless controller paging page 4-149 ping Sends ICMP echo messages to a user-specified location page 4-150 pwd Displays the current directory page 4-152 re-elect Re-elects tunnel wireless controller page 4-153 reload Halts the wireless controller and performs a warm reboot page 4-154 remote-debug Troubleshoots remote systems page 4-156 rename Renames a file in the existing file system page 4-158 rmdir Deletes an existing file from the file system page 4-160 self Displays the configuration context of the device page 4-162 ssh Connects to another device using a secure shell page 4-163 telnet Opens a Telnet session page 4-164 terminal Sets the length/number of lines displayed within the terminal window page 4-165 Command Description Reference
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 80 time-it Verifies the time taken by a particular command between request and response page 4-166 traceroute Traces the route to a defined destination page 4-167 upgrade Upgrades the software image page 4-168 upgrade-abort Aborts an ongoing software image upgrade page 4-170 watch Repeats the specific CLI command at a periodic interval page 4-171 clrscr Clears the display screen page 6-379 commit Commits (saves) the changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 81 ap-upgrade Privileged Exec Mode Commands Enables an automatic firmware upgrade on an adopted AP or a set of APs. APs of the same type can be upgraded together. Once APs have been upgraded, they can be forced to reboot. This command also loads the firmware on to the wireless controller. The AP upgrade command also upgrades APs in a specified RF Domain. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap-upgrade [<MAC/HOSTNAME>|all|ap4021|ap4600|ap4511|ap4521|ap4522|ap4532| ap4700|cancel-upgrade|load-imagerf-domain] ap-upgrade [<MAC/HOSTNAME>] {no-rebootreboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} ap-upgrade all {no-rebootreboot-time <TIME>|upgrade-time <TIME> {no- reboot|reboot-time <TIME>}} ap-upgrade [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}}{(staggered-reboot)}] ap-upgrade cancel-upgrade [<MAC/HOSTNAME>|all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700|on] ap-upgrade cancel-upgrade [<MAC/HOSTNAME>|all] ap-upgrade cancel-upgrade [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] all ap-upgrade cancel-upgrade on rf-domain [<RF-DOMAIN-NAME>|all] ap-upgrade load-image [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] <IMAGE-URL> ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-reboot|no-via-rf-domain|reboot-time <TIME>| staggered-reboot|upgrade-time <TIME>}
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 82 ap-upgrade rf-domain [<RF-DOMAIN-NAME>all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-reboot {staggered-reboot}|reboot-time <TIME> {staggered-reboot}} ap-upgrade rf-domain [<RF-DOMAIN-NAME>all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-via-rf-domain {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}}} {(staggered- reboot)} ap-upgrade rf-domain [<RF-DOMAIN-NAME>all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered-reboot)} Parameters ap-upgrade [<MAC/HOSTNAME>] {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} ap-upgrade all {no-reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot| reboot-time <TIME>}} {(staggered-reboot)} <MAC/HOSTNAME> Upgrades firmware on a specified AP or all APs adopted by the wireless controller. <MAC/HOSTNAME> Specify the MAC address or hostname of the AP. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted) reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade <TIME> Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. upgrade-time <TIME> {no-reboot|reboot-time <TIME>} Optional. Schedules an automatic firmware upgrade. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. The following actions can be performed after a scheduled upgrade: no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. all Upgrades firmware on all APs adopted by the wireless controller. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. <TIME> Optional. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 83 ap-upgrade [ap4021| ap4600| ap4511| ap4521| ap4522| ap4532| ap4700] al l no- reboot|reboot-time <TIME>|upgrade-time <TIME> {no-reboot| reboot-time <TIME>}} {(staggered-reboot)} ap-upgrade cancel-upgrade [<MAC/HOSTNAME>all] upgrade-time <TIME> {no-reboot|reboot-time <TIME>} Optional. Schedules firmware upgrade on an AP adopted by the wireless controller. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM formats. After a scheduled upgrade, these actions can be performed: no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enables staggered reboot (one at a time) without network impact. This keyword is common to all of the above. [ap4021|ap4600|ap4511|ap4521 |ap4522|ap4532|ap4700] all Upgrades firmware on all adopted APs AP4021 all Upgrades firmware on all AP4021s AP4600 all Upgrades firmware on all AP4600s AP4511 all Upgrades firmware on all AP4511s AP4522 all Upgrades firmware on all AP4522s AP4521 all Upgrades firmware on all AP4521s AP4532 all Upgrades firmware on all AP4532s AP4700 all Upgrades firmware on all AP4700s After selecting the AP type, you can schedule an automatic upgrade and/or an automatic reboot. no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted) reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade <TIME> Optional. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. upgrade-time <TIME> {no-reboot reboot-time <TIME>} Optional. Schedules firmware upgrade on an AP adopted by the wireless controller. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM formats. After a scheduled upgrade, these actions can be performed: no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. cancel-upgrade [ <MAC/HOSTNAME>|all] Cancels scheduled firmware upgrade on a specified AP or all APs adopted by the wireless controller. <MAC/HOSTNAME> Cancels a scheduled upgrade on a specified AP. Specify the MAC address or hostname of the AP. all Cancels scheduled upgrade on all APs.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 84 ap-upgrade cancel-upgrade [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532| ap4700] all ap-upgrade cancel-upgrade on rf-domain [<DOMAIN-NAME>|all] ap-upgrade load-image [ap4021|ap4600|ap4511|ap4521|ap4522|ap4532|ap4700] <IMAGE-URL> cancel-upgrade [ap4021|ap4600|ap4511|ap452 1|ap4522|ap4532|ap4700] all Cancels scheduled firmware upgrade on all adopted APs AP4021 all Cancels scheduled upgrade on all AP4021s AP4600 all Cancels scheduled upgrade on all AP4600s AP4511 all Cancels scheduled upgrade on all AP4511s AP4521 all Cancels scheduled upgrade on all AP4521s AP4522 all Cancels scheduled upgrade on all AP4522s AP4532 all Cancels scheduled upgrade on all AP4532s AP4700 all Cancels scheduled upgrade on all AP4700s cancel-upgrade on rf-domain [<RF-DOMAIN-NAME>|all] Cancels scheduled firmware upgrade on a specified RF Domain or all RF Domains. <RF-DOMAIN-NAME> Cancels a scheduled upgrade on a specified RF Domain. Specify the RF Domain name. all Cancels scheduled upgrades on all RF Domains. load-image [ap4021|ap4600|ap4511|ap452 1|ap4522|ap4532|ap4700] Loads AP firmware images on the wireless controller. Select the AP type and provide the location of the AP firmware image. AP4021 <IMAGE-URL> Loads AP4021 firmware image AP4600 <IMAGE-URL> Loads AP4600 firmware image AP4511 <IMAGE-URL> Loads AP4511 firmware image AP4521 <IMAGE-URL> Loads AP4521 firmware image AP4522 <IMAGE-URL> Loads AP4522 firmware image AP4532 <IMAGE-URL> Loads AP4532 firmware image AP4700 <IMAGE-URL> Loads AP4700 firmware image <IMAGE-URL> Specify the AP firmware image location in the following format: ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>:<passwd>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 85 ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-reboot {staggered-reboot}|reboot-time <TIME> {staggered-reboot}} ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {no-via-rf-domain {no-reboot|reboot-time <TIME>| upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered-reboot)} rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains. <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [ap4021|ap4600|ap4511|ap452 1|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s no-reboot {staggered-reboot} Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot <TIME> {staggered- reboot} Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enables staggered reboot (one at a time) without network impact. This keyword is common to all of the above. rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains. <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [ap4021|ap4600|ap4511|ap452 1|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s no-via-rf-domain Upgrades APs from the adopted device. no-reboot {staggered-reboot} Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted).
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 86 ap-upgrade rf-domain [<RF-DOMAIN-NAME>|all] [all|ap4021|ap4600|ap4511| ap4521|ap4522|ap4532|ap4700] {upgrade-time <TIME> {no-reboot|reboot-time <TIME>}} {(staggered-reboot)} reboot-time <TIME> {staggered-reboot} Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). upgrade-time <TIME> {no- reboot|reboot-time <TIME>} Optional. Schedules an automatic firmware upgrade. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. The following actions can be performed after a scheduled upgrade: no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enables staggered reboot (one at a time) without network impact. This keyword is common to all of the above. rf-domain [<RF-DOMAIN-NAME>|all] Upgrades AP firmware on devices in a specified RF Domain or all RF Domains. <RF-DOMAIN-NAME> Upgrades firmware in a specified RF Domain. Specify the RF Domain name. all Upgrades firmware on all RF Domains. [ap4021|ap4600|ap4511|ap452 1|ap4522|ap4532|ap4700] After specifying the RF Domain, select the AP type. all Upgrades firmware on all APs AP4021 Upgrades firmware on all AP4021s AP4600 Upgrades firmware on all AP4600s AP4511 Upgrades firmware on all AP4511s AP4521 Upgrades firmware on all AP4521s AP4522 Upgrades firmware on all AP4522s AP4532 Upgrades firmware on all AP4532s AP4700 Upgrades firmware on all AP4700s upgrade <TIME> Schedules AP firmware upgrade. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. no-reboot {staggered-reboot} Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> {staggered-reboot} Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). staggered-reboot Optional. Enables staggered reboot (one at a time) without network impact. This keyword is common to all of the above.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 87 Example wm3400-37FABE#ap-upgrade AP4021 all -------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE -------------------------------------------------------------------------- 00-15-70-37-FA-BE Fail Could not find any matching APs -------------------------------------------------------------------------- wm3400-37FABE# wm3400-37FABE#ap-upgrade default/ap no-reboot -------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE -------------------------------------------------------------------------- 00-15-70-37-FA-BE Success Queued 0 APs to upgrade -------------------------------------------------------------------------- wm3400-37FABE# upgrade-time <TIME> {no- reboot|reboot-time <TIME>} Optional. Schedules an automatic firmware upgrade. <TIME> Specify the upgrade time in the MM/DD/YYYY-HH:MM or HH:MM format. The following actions can be performed after a scheduled upgrade: no-reboot Optional. Disables automatic reboot after a successful upgrade (the wireless controller must be manually restarted). reboot-time <TIME> Optional. Schedules an automatic reboot after a successful upgrade. Specify the reboot time in the MM/DD/YYYY-HH:MM or HH:MM format. staggered-reboot Optional. Enables staggered reboot (one at a time) without network impact. This keyword is common to all of the above.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 88 archive Privileged Exec Mode Commands Manages file archive operations. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax archive tar /table [<FILE><URL>] archive tar /create [<FILE><URL>] <FILE> archive tar /xtract [<FILE><URL>] <DIR>] Parameters archive tar /table [<FILE><URL>] archive tar /create [<FILE><URL>] <FILE> archive tar /xtract [<FILE><URL>] <DIR>] tar Manipulates (creates, lists or extracts) a tar file /table Lists the files in a tar file <FILE> Defines a tar filename <URL> Sets the tar file URL tar Manipulates (creates, lists or extracts) a tar file /create Creates a tar file <FILE> Defines tar filename <URL> Sets the tar file URL tar Manipulates (creates, lists or extracts) a tar file /xtract Extracts content from a tar file <FILE> Defines tar filename <URL> Sets the tar file URL
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 89 Example How to zip the folder flash:/log/? wm3400-37FABE#archive tar /create flash:/out.tar flash:/log/ log/ log/vlan-usage.log log/dpd2.log log/upgrade.log log/dpd2.startup log/cfgd.log log/messages.log log/startup.log log/radius/ wm3400-37FABE# wm3400-37FABE#dir flash:/ Directory of flash:/ drwx Fri Aug 3 13:16:52 2012 log drwx Fri Jul 8 15:50:23 2011 Final drwx Mon Jul 18 15:16:35 2011 cache drwx Thu Jul 19 08:40:19 2012 crashinfo drwx Fri Aug 3 13:14:11 2012 archived_logs drwx Sat Jan 1 05:30:25 2000 hotspot drwx Sat Jan 1 05:30:09 2000 floorplans drwx Wed May 9 20:18:19 2012 startuplog -rw- 244736 Thu Aug 16 10:05:58 2012 out.tar wm3400-37FABE# <DIR> Specify a directory name. When used with /create, dir is the source directory for the tar file. When used with /xtract, dir is the destination file where contents of the tar file are extracted.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 90 boot Privileged Exec Mode Commands Specifies the image used after reboot Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax boot system [primarysecondary] {on <DEVICE-NAME>} Parameters boot system [primarysecondary] {on <DEVICE-NAME>} Example wm3400-37FABE#boot system primary on wm3400-37FABE Updated system boot partition wm3400-37FABE# system [primarysecondary] Specifies the image used after a device reboot primary Uses a primary image after reboot secondary Uses a secondary image after reboot on <DEVICE-NAME> Optional. Specifies the primary or secondary image location on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 91 captive-portal-page-upload Privileged Exec Mode Commands Uploads captive portal advanced pages. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax captive-portal-page-upload [<CAPTIVE-PORTAL-NAME>|cancel-upload|load-file] captive-portal-page-upload <CAPTIVE-PORTAL-NAME> [<MAC/HOSTNAME>|all|rf- domain] captive-portal-page-upload <CAPTIVE-PORTAL-NAME> [<MAC/HOSTNAME>|all] {upload-time <TIME>} captive-portal-page-upload <CAPTIVE-PORTAL-NAME> rf-domain [<DOMAIN- NAME>|all] {no-via-rf-domain} {(upload-time <TIME>)} captive-portal-page-upload cancel-upload [<MAC/HOSTNAME>|all|on rf-domain [<DOMAIN-NAME>|all]] captive-portal-pagce-upload load-file <CAPTIVE-PORTAL-NAME> <URL> Parameters capt i ve- por t al - page- upl oad <CAPTI VE- PORTAL- NAME> [ <MAC/ HOSTNAME>| al l ] {upload-time <TIME>} captive-portal-page-upload <CAPTIVE-PORTAL-NAME> Uploads advanced pages specified by the <CAPTIVE-PORTAL-NAME> parameter. <CAPTIVE-PORTAL-NAME> Specify captive portal name (should be existing and configured). <MAC/HOSTNAME> Uploads to a specified AP <MAC/HOSTNAME> Specify the APs MAC address or hostname. all Uploads to all APs. upload-time <TIME> Optional. Schedules an upload time. <TIME> Specify upload time in the MM/DD/YYYY-HH:MM or HH:MM format.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 92 capt i ve- por t al - page- upl oad <CAPTI VE- PORTAL- NAME> r f - domai n [ <DOMAI N- NAME>| al l ] {no-via-rf-domain} {(upload-time <TIME>)} capt i ve- por t al - page- upl oad cancel - upl oad [ <MAC/ HOSTNAME>| al l | on r f - domai n [ <DOMAI N- NAME>| al l ] capt i ve- por t al - page- upl oad l oad- f i l e <CAPTI VE- PORTAL- NAME> <URL> captive-portal-page-upload <CAPTIVE-PORTAL-NAME> Uploads advanced pages specified by the <CAPTIVE-PORTAL-NAME> parameter. <CAPTIVE-PORTAL-NAME> Specify captive portal name (should be existing and configured). rf-domain [<DOMAIN- NAME>|all] Uploads to all access points within a specified RF Domain or all RF Domains. <DOMAIN-NAME> Uploads to APs within a specified RF Domain. Specify the RF Domain name. all Uploads to APs across all RF Domains. no-via-rf-domain Optional. Uploads to Aps from the adopted device. upload-time <TIME> Optional. Schedules an AP upload. <TIME> Specify upload time in the MM/DD/YYYY-HH:MM or HH:MM format. captive-portal-page-upload cancel-upload Cancels a scheduled AP upload. cancel-upload [<MAC/ HOSTNAME>|all|on rf- domain [<DOMAIN- NAME>|all] Select one of the following options: <MAC/HOSTNAME> Cancels a scheduled upload to specified AP. Specify AP MAC address or hostname. all Cancels all scheduled AP uploads. on rf- domain Cancels all scheduled uploads within a specified RF Domain or all RF Domains. <DOMAIN-NAME> Cancels scheduled uploads within a specified RF Domain. Specify RF Domain name. all Cancels scheduled uploads across all RF Domains. captive-portal-page-upload load-file Loads captive-portal advanced pages. <CAPTIVE-PORTAL-NAME> <URL> Specify captive portal name (should be existing and configured) and location. <URL> Specifies file location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>:<passwd>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb<n>:/path/file
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 93 Example wm3400-37FABE>captive-portal-page-upload test 00-04-96-4A-A7-08 upload-time 07/15/2012-12:30 --------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE --------------------------------------------------------------------------- 00-15-70-37-FA-BE Fail Failed to initiate page upload --------------------------------------------------------------------------- wm3400-37FABE> wm3400-37FABE>captive-portal-page-upload cancel-upload 00-04-96-4A-A7-08 --------------------------------------------------------------------------- CONTROLLER STATUS MESSAGE --------------------------------------------------------------------------- 00-15-70-37-FA-BE Success Cancelled upgrade of 1 APs --------------------------------------------------------------------------- wm3400-37FABE>
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 94 cd Privileged Exec Mode Commands Changes the current directory Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cd {<DIR>} Parameters cd {<DIR>} Example wm3400-37FABE#cd flash:/log/ wm3400-37FABE#pwd flash:/log/ wm3400-37FABE# <DIR> Optional. Changes the current directory to DIR. If a directory name is not provided, the system displays the current directory name.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 95 change-passwd Privileged Exec Mode Commands Changes the password of a logged user. When this command is executed without any parameters, the password can be changed interactively. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax change-passwd {<OLD-PASSWORD> <NEW-PASSWORD>} Parameters change passwd {<OLD-PASSWORD> <NEW-PASSWORD>} Usage Guidelines A password must be from 164 characters. Example wm3400-37FABE#change-passwd Enter old password: Enter new password: Password for user 'admin' changed successfully Please write this password change to memory(write memory) to be persistent. wm3400-37FABE#write memory OK wm3400-37FABE# <OLD-PASSWORD> Optional. Specify the password to be changed. <NEW-PASSWORD> Specify the new password. NOTE: The password can also be changed interactively. To do so, press [Enter] after the command
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 96 clear Privileged Exec Mode Commands Clears parameters, cache entries, table entries, and other entries. The clear command is available for specific commands only. The information cleared using this command varies depending on the mode where the clear command is executed. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 NOTE Refer to the interface details below when using clear Interface details: ge <index> WM3400 supports 5GEs, WM3600 supports 8 GEs and WM3700 supports 4GEs me1 Available in both WM3700 and WM3600 - up1 - Uplink interface on WM3400 Syntax clear [arp-cache|cdp|counters|crypto|event-history|firewall|ip|lldp| logging|rtls|spanning-tree|vrrp] clear arp-cache {on <DEVICE-NAME>} clear [cdp|lldp] neighbors {on <DEVICE-NAME>} clear counters [all|bridge|interface|router|thread] clear counters interface [<INTERFACE>|all|ge <1-4>|me1|port-channel <1-2>| pppoe1|vlan <1-4094>|wwan1] clear crypto [ike|ipsec] clear crypto ike sa [<IP>|all] {on <DEVICE-NAME>} clear crypto ipsec sa {on <DEVICE-NAME>} clear event-history clear firewall [dhcp snoop-table|dos stats|flows] {on <DEVICE-NAME>}
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 97 clear ip [dhcp|ospf] clear ip dhcp bindings [<IP>|all] {on <DEVICE-NAME>} clear ip ospf process {on <DEVICE-NAME>} clear logging {on <DEVICE-NAME>} clear rtls [aeroscout|ekahau] clear rtls [aeroscout|ekahau] {<DEVICE-NAME> {on <DEVICE-OR-DOMAIN-NAME>}| on <DEVICE-OR-DOMAIN-NAME>} clear spanning-tree detected-protocols {interface]on <DEVICE-NAME>} clear spanning-tree detected-protocols {interface]<INTERFACE>]ge <1-4>]me1] port-channel <1-2>]pppoe1]vlan <1-4094>]wwan1]} {on <DEVICE-NAME>} cl ear vr r p [ er r or - st at s| st at s] {on <DEVICE-NAME>} Parameters clear arp-cache {on <DEVICE-NAME>} clear [cdp|lldp] neighbors {on <DEVICE-NAME>} clear counters [all|bridge|router|thread] arp-cache Clears ARP (Address Resolution Protocol) cache entries on an AP or wireless controller. on <DEVICE-NAME> Optional. Clears ARP cache entries on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. cdp Clears CDP (Cisco Discovery Protocol) table entries. ldp Clears LLDP (Link Layer Discovery Protocol) neighbor table entries. neighbors Clears CDP or LLDP neighbor table entries based on the option selected in the preceding step. on <DEVICE-NAME> Optional. Clears CDP or LLDP neighbor table entries on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. counters[all|bridge|router| thread] Clears counters on a system. all Clears all counters irrespective of the interface type. bridge Clears bridge counters. router Clears router counters. thread Clears per-thread counters.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 98 cl ear count er s i nt er f ace [ <I NTERFACE>| al l | ge <1- 4>| me1| por t - channel <1- 2>| pppoe1| vl an <1- 4094>| wwan1] cl ear cr ypt o i ke sa [ <I P>| al l ] {on <DEVICE-NAME>} cl ear cr ypt o i psec sa {on <DEVICE-NAME>} clear event-history cl ear f i r ewal l [ dhcp snoop- t abl e| dos st at s| f l ows] {on <DEVICE-NAME>} counters interface [<INTERFACE>|all|ge <1-4>| me1|port-channel <1-2>| pppoe1|vlan <1-4094>|wwan1] Clears interface counters for a specified interface. <INTERFACE> Clears a specified interface counters. Specify the interface name. all Clears all interface counters. ge <1-4> Clears GigabitEthernet interface counters. Specify the GigabitEthernet interface index from 14. me1 Clears FastEthernet interface counters port-channel <1-2> Clears port-channel interface counters. Specify the port channel interface index from 12. pppoe1 Clears Point-to-Point Protocol over Ethernet (PPPoE) interface counters. vlan <1-4094> Clears interface counters. Specify the Switch Virtual Interface (SVI) VLAN ID from 14094. wwan1 Clears wireless WAN interface counters. crypto Clears encryption module database. ike sa [<IP>|all] Clears IKE (Internet Key Exchange) security associations (SAs). <IP> Clears IKE SAs for a certain peer. all Clears IKE SAs for all peers. on <DEVICE-NAME> Optional. ClearsIKE SA entries for a specified peer or all peers on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. crypto Clears encryption module database. ipsec sa {on <DEVICE-NAME>} Clears ISPec (Internet Protocol Security) database SAs. on <DEVICE-NAME> Optional. Clears IPSec SA entries on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. event-history Clears event history cache entries. firewall Clears firewall event entries. DHCP snoop-table Clears DHCP snoop table entries. dos stats Clears denial of service statistics. flows Clears established firewall sessions. on <DEVICE-NAME> Optional. Clears a specified address binding or all address bindings on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 99 clear ip dhcp bindings [<IP>|all] {on <DEVICE-NAME>} cl ear i p ospf pr ocess {on <DEVICE-NAME>} cl ear r t l s [ aer oscout | ekahau] {<DEVICE-NAME> {on <DEVICE-OR-DOMAIN-NAME>}| on <DEVICE-OR-DOMAIN-NAME>} clear spanning-tree detected-protocols {on <DEVICE-NAME>} cl ear spanni ng- t r ee det ect ed- pr ot ocol s {interface [<INTERFACE>|ge <1-4>|me1| port-channel <1-2>|pppoe1|vlan <1-4094>|wwan1]} {on <DEVICE-NAME>} ip Clears DHCP server IP address bindings. dhcp bindings Clears DHCP servers connections and address binding entries. <IP> Clears specific address binding entries. Specify the IP address to clear binding entries. all Clears DHCP address binding entries on all DHCP servers on <DEVICE-NAME> Optional. Clears a specified address binding or all address bindings on a specified AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. ip ospf process Clears firewall event entries. on <DEVICE-NAME> Optional. Clears OSFP (Open Shortest Path First) process on a specified AP or wireless controller. OSPF is a link-state interior gateway protocol (IGP). OSPF routes IP packets within a single routing domain (autonomous system), like an enterprise LAN. OSPF gathers link state information from neighbor routers and constructs a network topology. The topology determines the routing table presented to the Internet Layer which makes routing decisions based solely on the destination IP address found in IP packets. <DEVICE-NAME> Specify the name of the AP or wireless controller. rtls Clears RTLS (Real Time Location Service) statistics. aeroscout Clears RTLS AeroScout statistics. ekahau Clears RTLS Ekahau statistics. <DEVICE-NAME> This keyword is common to the aeroscout and ekahau parameters. <DEVICE-NAME> Optional. Clears AeroScout or Ekahau RTLS statistics on a specified AP or wireless controller. <DEVICE-OR-DOMAIN- NAME> This keyword is common to the aeroscout and ekahau parameters. <DEVICE-OR-DOMAIN-NAME> Optional. Clears AeroScout or Ekahau RTLS statistics on a specified AP, wireless controller, or RF Domain. spanning-tree Clears spanning tree protocols on an interface, and also restarts protocol migration. detected-protocols Restarts protocol migration. on <DEVICE-NAME> Optional. Clears spanning tree protocols on a specified device. <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller. spanning-tree Clears spanning tree protocols on an interface and restarts protocol migration. detected-protocols Restarts protocol migration.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 100 clear vrrp [error-stats|stats] {on <DEVICE-NAME>} Example wm3400-37FABE>clear crypto isakmp sa 111.222.333.01 on wm3400-37FABE wm3400-37FABE> wm3400-37FABE>clear event-history wm3400-37FABE> wm3400-37FABE>clear spanning-tree detected-protocols interface port-channel 1 on wm3400-37FABE wm3400-37FABE> wm3400-37FABE>clear ip dhcp bindings 172.16.10.9 on wm3400-37FABE wm3400-37FABE> wm3400-37FABE#clear cdp neighbors on wm3400-37FABE wm3400-37FABE# WM3400-880DA7#clear spanning-tree detected-protocols interface ge 1 WM3400-880DA7# WM3400-880DA7#clear lldp neighbors WM3400-880DA7# interface [<INTERFACE>|ge <1-4>|me1|port-channel <1-2>| pppoe1|vlan <1-4094>|wwan1] Optional. Clears spanning tree protocols on different interfaces. <INTERFACE> Clears detected spanning tree protocol on a specified interface. Specify the interface name. ge <1-4> Clears detected spanning tree protocol for the selected GigabitEthernet interface. Select the GigabitEthernet interface index from 14. me1 Clears FastEthernet interface status (up1 - Clears the uplink interface). port-channel <1-2> Clears detected spanning tree protocol for the selected port channel interface. Select the port channel index from 12. pppoe1 Clears detected spanning tree protocol for Point-to-Point Protocol over Ethernet (PPPoE) interface. vlan <1-4094> Clears detected spanning tree protocol for the selected VLAN interface. Select a SVI VLAN ID from 14094. wwan1 Clears detected spanning tree protocol for wireless WAN interface. on <DEVICE-NAME> Optional. Clears spanning tree protocol entries on a selected AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. vrrp Clears VRRP (Virtual Router Redundancy Protocol) statistics for a device. error-stats {on <DEVICE- NAME>} Clears global error statistics. on <DEVICE-NAME> Optional. Clears VRRP global error statistics on a selected AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Clears spanning tree protocols on a specified device. <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 101 clock Privileged Exec Mode Commands Sets a devices system clock Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax clock set <HH:MM:SS> <1-31> <MONTH> <1993-2035> {on <DEVICE-NAME>} Parameters clock set <HH:MM:SS> <1-31> <MONTH> <1993-2035> {on <DEVICE-NAME>} Example wm3400-37FABE#clock set 16:01:45 20 Mar 2012 on wm3400-37FABE wm3400-37FABE# wm3400-37FABE#show clock 2012-03-20 16:01:53 UTC wm3400-37FABE# clock set Sets a devices system clock <HH:MM:SS> Sets the current time (in military format hours, minutes and seconds) <1-31> Sets the numerical day of the month <MONTH> Sets the month of the year (Jan to Dec) <1993-2035> Sets a valid four digit year from 1993 - 2035 on <DEVICE-NAME> Optional. Sets the clock on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 102 cluster Privileged Exec Mode Commands Initiates the cluster context. The cluster context provides centralized management to configure all cluster members from any one member. Commands executed under this context are executed on all members of the cluster. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cluster start-election Parameters cluster start-election Example wm3400-37FABE#cluster start-election wm3400-37FABE# Related Commands start-selection Starts a new cluster master election. create-cluster Creates a new cluster on a specified device join-cluster Adds a wireless controller, as a cluster member, to an existing cluster of devices
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 103 configure Privileged Exec Mode Commands Enters the configuration mode. Use this command to enter the current devices configuration mode, or enable configuration from the terminal. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax configure {self|terminal} Parameters configure {self|terminal} Example wm3400-37FABE#configure self Enter configuration commands, one per line. End with CNTL/Z. wm3400-37FABE(config-device-00-15-70-37-FA-BE)# wm3400-37FABE#configure terminal Enter configuration commands, one per line. End with CNTL/Z. wm3400-37FABE(config)# self Optional. Enables the current devices configuration mode. terminal Optional. Enables configuration from the terminal.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 104 connect Privileged Exec Mode Commands Begins a console connection to a remote device using the remote devices MiNT ID or name Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax connect [mint-id <MINT-ID>|<REMOTE-DEVICE-NAME>] Parameters connect [mint-id <MINT-ID>|<REMOTE-DEVICE-NAME>] Example wm3400-37FABE#connect mint-id 01.4A.A7.08 Entering character mode Escape character is '^]'. AP4700 release 5.4.0.0-015D AP4700 login: admin Password: AP4700> wm3400-37FABE#show mint lsp-db on wm3400-37FABE 3LSPs in LSP-db of 70.37.FA.BE: LSP 01.4A.A7.08 at level 1, hostname "AP4700", 2adjacencies, seqnum 284 LSP 70.37.FA.BE at level 1, hostname "wm3400-37FABE", 1 adjacencies, seqnum 83325 mint-id <MINT-ID> Connects to a remote system using the MiNT ID <MINT-ID> Specify the remote device MiNT ID. <REMOTE-DEVICE-NAME> Connects to a remote system using its name <REMOTE-DEVICE-NAME> Specify the remote device name.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 105 LSP 70.38.06.49 at level 1, hostname "WM3600-380649", 1 adjacencies, seqnum 9275 wm3400-37FABE# wm3400-37FABE#connect mint-id 70.38.06.49 Entering character mode Escape character is '^]'.WM3600 release 5.2.3.0-032R WM3600-380649 login: admin Password: wm3400-37FABE>
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 106 copy Privileged Exec Mode Commands Copies a file (config,log,txt...etc) from any location to the wireless controller and vice-versa. NOTE Copying a new config file onto an existing running-config file merges it with the existing running-config on the wireless controller. Both the existing running-config and the new config file are applied as the current running- config. Copying a new config file onto a start-up config files replaces the existing start-up config file with the parameters of the new file. It is better to erase the existing start-up config file and then copy the new config file to the startup config. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax copy [<SOURCE-FILE>|<SOURCE-URL>] [<DESTINATION-FILE>|<DESTINATION-URL>] Parameters copy [<SOURCE-FILE>|<SOURCE-URL>] [<DESTINATION-FILE>|<DESTINATION-URL>] Example Transferring file snmpd.log to remote tftp server. wm3400-37FABE#copy flash:/log/snmpd.log tftp://157.235.208.105:/snmpd.log Accessing running-config file from remote tftp server into switch running-config. wm3400-37FABE#copy tftp://157.235.208.105:/running-config running-config <SOURCE-FILE> Specify the source file to copy. <SOURCE-URL> Specify the source file URL. <DESTINATION-FILE> Specify the destination file to copy to. <DESTINATION-URL> Specify the destination file URL.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 107 create-cluster Privileged Exec Mode Commands Creates a new cluster on a specified device. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax create-cluster name <CLUSTER-NAME> ip <IP> {level [1|2]} Parameters create-cluster name <CLUSTER-NAME> ip <IP> {level [1|2]} Example wm3400-37FABE>create-cluster name Cluster1 ip 172.16.10.1 level 1 ... creating cluster ... committing the changes ... saving the changes [OK] wm3400-37FABE> create-cluster Creates a cluster. name <CLUSTER-NAME> Configures the cluster name. <CLUSTER-NAME> Specify a cluster name. ip <IP> Specifies the devices IP address used for cluster creation <IP> Specify the devices IP address in the A.B.C.D format. level [1|2] Optional. Configures the routing level for this cluster. 1 Configures level 1 (local) routing. 2 Configures level 2 (inter-site) routing.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 108 Related Commands cluster Initiates the cluster context. The cluster context provides centralized management to configure all cluster members from any one member. join-cluster Adds a wireless controller, as a cluster member, to an existing cluster of devices
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 109 crypto Privileged Exec Mode Commands Enables digital certificate configuration and RSA Keypair management. Digital certificates are issued by CAs and contain user or device specific information, such as name, public key, IP address, serial number, company name etc. Use this command to generate, delete, export, or import encrypted RSA Keypairs and generate Certificate Signing Requests (CSRs). This command also enables trustpoint configuration. Trustpoints contain the Certificate Authoritys (CA) identity and configuration parameters. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax crypto [key|pki] crypto key [export|generate|import|zeroise] crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {background|on|passphrase} crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} crypto key export rsa <RSA-KEYPAIR-NAME> <EXPORT-TO-URL> {passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE- NAME>}} crypto key generate rsa <RSA-KEYPAIR-NAME> <1024-2048> {on <DEVICE-NAME>} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {background|on|passphrase} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-FROM-URL> {passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE- NAME>}} crypto key zeroise rsa <RSA-KEYPAIR-NAME> {force {on <DEVICE-NAME>}|on <DEVICE-NAME>}
TM 4000 Series Access Point CLI Reference Guide 111 crypto key generate rsa <RSA-KEYPAIR-NAME> <1024-2048> {on <DEVICE-NAME>} crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-TO-URL> {background} {on <DEVICE-NAME>}|on <DEVICE-NAME>} <EXPORT-TO-URL> {on <DEVICE-NAME>} Specify the RSA Keypair destination address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE- NAME>} Optional. Performs an export operation in the background. Optionally specify the device (AP/wireless controller) to export to. on <DEVICE-NAME> Optional. Performs an export operation to a specific device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. generate rsa <RSA-KEYPAIR-NAME> <1024-2048> Generates a new RSA Keypair. <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <1024-2048> Specify the size of the RSA key in bits from 10242048. on <DEVICE-NAME> Optional. Generates a new RSA Keypair on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. import rsa <RSA-KEYPAIR-NAME> Imports a RSA Keypair from a specified source <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <IMPORT-TO-URL> Specify the RSA Keypair source address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file on <DEVICE-NAME> Optional. Performs an import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. background {on <DEVICE- NAME>} Optional. Performs an import operation in the background. on <DEVICE-NAME> Optional. Performs import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 112 crypto key import rsa <RSA-KEYPAIR-NAME> <IMPORT-TO-URL> {passphrase <KEY- PASSPHRASE>} {background {on <DEVICE-NAME>}|on <DEVICE-NAME>} crypto key zeroise <RSA-KEYPAIR-NAME> {force {on <DEVICE-NAME>}|on <DEVICE- NAME>} crypto pki authenticate <TRUSTPOINT-NAME> <URL> {background {on <DEVICE- NAME>}|on <DEVICE-NAME>} key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. import rsa <RSA-KEYPAIR-NAME> Decrypts and imports RSA Keypair from a specified source <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. <IMPORT-TO-URL> {passphrase <KEY- PASSPHRASE>} Specify the RSA Keypair source address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file passphrase Optional. Decrypts RSA Keypair before importing it. <KEY-PASSPHRASE> Specify the passphrase to decrypt the RSA Keypair. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. key Enables RSA Keypair management. Use this command to export, import, generate, or delete a RSA key. zeroise rsa <RSA-KEYPAIR-NAME> Deletes a specified RSA Keypair. <RSA-KEYPAIR-NAME> Specify the RSA Keypair name. NOTE: All device certificates associated with this key will also be deleted. force {on <DEVICE-NAME>} Optional. Forces deletion of all certificates associated with the specified RSA Keypair. Optionally specify a device (AP/wireless controller) on which to force certificate deletion.on <DEVICE-NAME> Optional. Forces deletion of all certificates on a specified device. on <DEVICE-NAME> Optional. Deletes all certificates associated with the RSA Keypair on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI (Private Key Infrastructure) management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA (Certificate Authority) certificates. authenticate <TRUSTPOINT-NAME> Authenticates atrustpoint and imports the corresponding CA certificate. <TRUSTPOINT-NAME> Specify the trustpoint name.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 113 crypto pki export request [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> autogen-subject-name [url <EXPORT-TO-URL>, email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>] <URL> Specify the CA certificate location in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE-NAME>} Optional. Performs authentication in the background. Optionally specify a device (AP/wireless controller) on which to perform authentication. on <DEVICE-NAME> Optional. Performs authentication on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. export request Exports CSR (Certificate Signing Request) to the CA for digital identity certificate. The CSR contains applicants details and RSA Keypairs public key. [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair or uses an existing RSA Keypair. generate-rsa-key Generates a new RSA Keypair for digital authentication. use-rsa-key Uses an existing RSA Keypair for digital authentication. <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If an existing RSA Keypair, specify its name. autogen-subject-name Auto-generates the subject name from configuration parameters. The subject name helps to identify the certificate. url <EXPORT-TO-URL> {background {on <DEVICE- NAME}| on <DEVICE-NAME>} Specify the location of the CA in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file NOTE: The CSR is exported to the specified location. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. email <SEND-TO-EMAIL> Exports CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the e-mail address of the CA. fqdn <FQDN> Exports CSR to a specified FQDN (Fully Qualified Domain Name) <FQDN> Specify the FQDN of the CA. ip address <IP> Exports CSR to a specified device or system. <IP> Specify the IP address of the CA.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 114 crypto pki export request [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> subject-name <COUNTRY> <STATE> <CITY> <ORGANIZATION> <ORGANIZATION-UNIT> [url <EXPORT-TO-URL>, email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>] crypto pki export trustpoint <TRUSTPOINT-NAME> <EXPORT-TO-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>|passphrase <KEY-PASSPHRASE> background {on <DEVICE-NAME>}|{on <DEVICE-NAME>}} pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. export request Exports aCSR to the CA for digital identity certificate. The CSR contains the applicants details and the RSA Keypairs public key. [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair, or uses an existing RSA Keypair. generate-rsa-key Generates a new RSA Keypair for digital authentication. use-rsa-key Uses an existing RSA Keypair for digital authentication. <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. subject-name <COMMON-NAME> Specifies subject name to identify the certificate. <COMMON-NAME> Specify the common name used with the CA certificate. The name should enable you to identify the certificate easily (264 characters in length). <COUNTRY> Sets the deployment country name (2 character ISO code). <STATE> Sets the state name (264 characters). <CITY> Sets the city name (264 characters).. <ORGANIZATION> Sets the organization name (264 characters). <ORGANIZATION-UNIT> Sets the organization unit (264 characters). url <EXPORT-TO-URL> {background {on <DEVICE- NAME}|on <DEVICE-NAME>} Specify thelocation of the CA in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file NOTE: The CSR is exported to the specified location. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. email <SEND-TO-EMAIL> Exports CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the e-mail address of the CA. fqdn <FQDN> Exports CSR to a specified FQDN. Specify the FQDN of the CA. ip address <IP> Exports the CSR to a specified device or system. Specify the IP address of the CA. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 115 crypto pki generate self-signed <TRUSTPOINT-NAME> [generate-rsa-key|use- rsa-key]<RSA-KEYPAIR-NAME> autogen-subject-name [email <SEND-TO-EMAIL>, fqdn <FQDN>, ip-address <IP>, on <DEVICE-NAME>] export trustpoint <TRUSTPOINT-NAME> Exports a trustpoint along with CA certificate, Certificate Revocation List (CRL), server certificate, and private key. <TRUSTPOINT-NAME> Specify the trustpoint name. <EXPORT-TO-URL> Specify the destination address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on-DEVICE-NAME>} Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. passphrase <KEY-PASSPHRASE> {background {on <DEVICE- NAME>} on <DEVICE-NAME> Optional. Encrypts key with a passphrase before exporting it. <KEY-PASSPHRASE> Specify the passphrase. background Optional. Performs the export operation in the background. on <DEVICE-NAME> Optional. Performs the export operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. generate Generates a CA certificate and a trustpoint. self-signed <TRUSTPOINT-NAME> Generates a self-signed CA certificate and a trustpoint. <TRUSTPOINT-NAME> Specify a name for the certificate and its trustpoint. [generate-rsa-key use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair, or uses an existing RSA Keypair. generate-rsa-key Generates a new RSA Keypair for digital authentication. use-rsa-key Uses an existing RSA Keypair for digital authentication. <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. autogen-subject-name Auto-generates the subject name from configuration parameters. The subject name helps to identify the certificate. email <SEND-TO-EMAIL> Exports CSR to a specified e-mail address <SEND-TO-EMAIL> Specify the e-mail address of the CA. fqdn <FQDN> Exports CSR to a specified FQDN. <FQDN> Specify the FQDN of the CA. ip-address <IP> Exports CSR to a specified device or system. <IP> Specify the IP address of the CA.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 116 cr ypt o pki gener at e sel f - si gned <TRUSTPOI NT- NAME> [ gener at e- r sa- key| use- r sa- key] <RSA- KEYPAI R- NAME> subj ect - name <COMMON- NAME> <COUNTRY> <STATE> <CI TY> <ORGANI ZATI ON> <ORGANI ZATI ON- UNI T> [ emai l <SEND- TO- EMAI L>, f qdn <FQDN>, i p- addr ess <I P>, on <DEVI CE- NAME>] crypto pki import [certificate|crl] <TRUSTPOINT-NAME> <IMPORT-FROM-URL> {background {on <DEVICE-NAME>}|on <DEVICE--NAME>} on <DEVICE-NAME> Exports the CSR on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. generate self-signed <TRUSTPOINT-NAME> Generates a self-signed CA certificate and a trustpoint. <TRUSTPOINT-NAME> Specify a name for the certificate and its trustpoint. [generate-rsa-key|use-rsa-key] <RSA-KEYPAIR-NAME> Generates a new RSA Keypair, or uses an existing RSA Keypair. generate-rsa-key Generates a new RSA Keypair for digital authentication. use-rsa-key Uses an existing RSA Keypair for digital authentication. <RSA-KEYPAIR-NAME> If generating a new RSA Keypair, specify a name for it. If using an existing RSA Keypair, specify its name. subject-name <COMMON-NAME> Enter a subject name to identify the certificate. <COMMON-NAME> Specify the common name used with the CA certificate. The name should enable you to identify the certificate easily. <COUNTRY> Sets the deployment country name (2 character ISO code). <STATE> Sets the state name (264 characters). <CITY> Sets the city name (264 characters).. <ORGANIZATION> Sets the organization name (264 characters). <ORGANIZATION-UNIT> Sets the organization unit (264 characters). email <SEND-TO-EMAIL> Exports CSR to a specified e-mail address. <SEND-TO-EMAIL> Specify the e-mail address of the CA. fqdn <FQDN> Exports CSR to a specified FQDN. <FQDN> Specify the FQDN of the CA. ip address <IP> Exports the CSR to a specified device or system. <IP> Specify the IP address of the CA. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. import Imports certificates, a CRL (Certificate Revocation List), or a trustpoint to a selected device [certificate|crl] <TRUSTPOINT-NAME> Imports a signed server certificate or a certificate revocation list. certificate Imports a signed server certificate. crl Imports a CRL. <TRUSTPOINT-NAME> Specify the trustpoint name (should be authenticated).
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 117 crypto pki import trustpoint <TRUSTPOINT-NAME> <IMPORT-FROM-URL> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>|passphrase <KEY-PASSPHRASE> {background {on <DEVICE-NAME>}|on <DEVICE-NAME>}} <IMPORT-FROM-URL> Specify the signed server certificate or CRL source address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE-NAME>} Optional. Performs the import operation in the background. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Enter the name of the AP or wireless controller. pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. import Imports certificates, CRL, or a trustpoint to the selected device trustpoint <TRUSTPOINT-NAME> Imports a trustpoint and its associated CA certificate, server certificate, and private key <TRUSTPOINT-NAME> Specify the trustpoint name (should be authenticated). <IMPORT-FROM-URL> Specify the signed server certificate or CRL source address in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background {on <DEVICE-NAME>} Optional. Performs the import operation in the background. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Performs the import operation on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. passphrase <KEY-PASSPHRASE> {background {on <DEVICE- NAME>}|on <DEVICE- NAME>} Optional. Encrypts trustpoint with a passphrase before importing it. <KEY-PASSPHRASE> Specify a passphrase. background Optional. Imports encrypted trustpoint in the background. on <DEVICE-NAME> Optional. Imports encrypted trustpoint on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 118 crypto pki zeroise trustpoint <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} Example wm3400-37FABE>crypto key generate rsa key 1025 RSA Keypair successfully generated wm3400-37FABE> wm3400-37FABE>crypto key import rsa en123 url passphrase word background on wm3400-37FABE RSA key import operation is started in background wm3400-37FABE> wm3400-37FABE>crypto pki generate self-signed word generate-rsa-key word autogen-subject-name fqdn word Successfully generated self-CA certificate> wm3400-37FABE>crypto pki zeroize trustpoint word del-key on wm3400-37FABE Successfully removed the trustpoint and associated certificates %Warning: Applications associated with the trustpoint will start using default-trustpoint wm3400-37FABE> wm3400-37FABE>crypto pki authenticate word url background on wm3400-37FABE Import of CA certificate started in background wm3400-37FABE#> wm3400-37FABE>crypto pki import trustpoint word url passphrase word on wm3400-37FABE Import operaton started in background wm3400-37FABE> Related Commands pki Enables PKI management. Use this command to authenticate, export, generate, or delete a trustpoint and its associated CA certificates. zeroise <TRUSTPOINT-NAME> Deletes a trustpoint and its associated CA certificate, server certificate, and private key. <TRUSTPOINT-NAME> Specify the trustpoint name. del-key {on <DEVICE-NAME>} Optional. Deletes the private key associated with the server certificate. on <DEVICE-NAME> Optional. Deletes the private key on a specified device. <DEVICE-NAME> Enter the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Deletes trustpoint on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. no Resets or disables the crypto commands
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 119 delete Privileged Exec Mode Commands Deletes a specified file from the devices file system Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax delete [/force <FILE>|/recursive <FILE>|<FILE>] Parameters delete [/force <FILE>|/recursive <FILE>|<FILE>] Example wm3400-37FABE#delete flash:/out.tar flash:/out.tar.gz Delete flash:/out.tar [y/n]? y Delete flash:/out.tar.gz [y/n]? y wm3400-37FABE#delete /force flash:/tmp.txt wm3400-37FABE# wm3400-37FABE#delete /recursive flash:/backup/ Delete flash:/backup//fileMgmt_350_180B.core [y/n]? y Delete flash:/backup//fileMgmt_350_18212X.core_bk [y/n]? n /force Forces deletion without a prompt. /recursive Performs a recursive delete. <FILE> Specifies the filenames to delete.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 120 Delete flash:/backup//imish_1087_18381X.core.gz [y/n]? n wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 121 diff Privileged Exec Mode Commands Displays the differences between two files on a devices file system or particular URL. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax diff [<FILE>|<URL>] [<FILE>|<URL>] Parameters diff [<FILE>|<URL>] [<FILE>|<URL>] Example wm3400-37FABE#diff startup-config running-config --- startup-config +++ running-config @@ -1,3 +1,4 @@ +!### show running-config ! ! Configuration of RFS7000 version 5.4.0.0-015D ! @@ -327,44 +328,38 @@ logging buffered warnings ! ap4700 00-04-96-4A-A7-08 - radio-count 2 use profile default-ap71xx use rf-domain default - hostname ap4700-4AA708 <FILE> The first <FILE> is the source file for the diff command. The second <FILE> is used for comparison. <URL> The first <URL> is the source files URL. The second <URL> is the second files URL.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 122 - license AP VIRTUAL_CONTROLLER_DEFAULT_AP_LICENSE - no staging-config-learnt - model-number AP4700-WW + hostname AP4700 + ip default-gateway 172.16.10.7 + interface vlan1 + ip address 172.16.10.23/24 + controller host 172.16.10.7 --More--
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 123 dir Privileged Exec Mode Commands Lists files on a devices file system. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dir {/all|/recursive|<DIR>|all-filesystems} Parameters dir {/all|/recursive|<DIR>|all-filesystems} Example wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 04:08:22 2012 log drwx Fri Jul 8 10:20:23 2011 test drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE# wm3400-37FABE#dir all-filesystems Directory of flash:/ /all Optional. Lists all files. /recursive Optional. Lists files recursively. <DIR> Optional. Lists files in the named file path. all-filesystems Optional. Lists files on all file systems.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 124 drwx Wed Mar 21 04:08:22 2012 log drwx Fri Jul 8 10:20:23 2011 test drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar Directory of nvram:/ -rw- 3460 Fri Dec 11 14:42:44 2009 startup-config.save -rw- 1638 Tue Jan 5 14:27:17 2010 startup-config-unused -rw- 3393 Mon Dec 14 13:55:51 2009 startup-config.save.1 -rw- 9392 Fri Dec 2 10:33:40 2011 startup-config.save.2 -rw- 8192 Fri Dec 2 10:39:58 2011 startup-config.save.3 -rw- 9395 Fri Dec 2 10:39:58 2011 startup-config.save.4 -rw- 185 Mon Mar 19 13:57:31 2012 licenses -rw- 9728 Tue Mar 20 12:52:56 2012 startup-config Directory of system:/ --More-- wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 125 disable Privileged Exec Commands Turns off (disables) the privileged mode command set. This command returns to the User Executable mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax disable Parameters None Example wm3400-37FABE#disable wm3400-37FABE>
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 126 edit Privileged Exec Mode Commands Edits a text file on the devices file system Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax edit <FILE> Parameters edit <FILE> Example wm3400-37FABE#edit startup-config GNU nano 1.2.4 File: startup-config ! ! Configuration of WM3700 version 5.4.0.0-015D ! ! version 2.1 ! ! ip access-list BROADCAST-MULTICAST-CONTROL permit tcp any any rule-precedence 10 rule-description "permit all TCP traffic" permit udp any eq 67 any eq dhcpc rule-precedence 11 rule-description "permit $ deny udp any range 137 138 any range 137 138 rule-precedence 20 rule- descripti$ deny ip any 224.0.0.0/4 rule-precedence 21 rule-description "deny IP multicast" <FILE> Specify the name of the file to modify.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 127 deny ip any host 255.255.255.255 rule-precedence 22 rule-description "deny IP $ permit ip any any rule-precedence 100 rule-description "permit all IP traffic" ! ip access-list test ! mac access-list PERMIT-ARP-AND-IPv4 permit any any type ip rule-precedence 10 rule-description "permit all IPv4 tr$ [ Read 353 lines ] ^G Get Help ^O WriteOut ^R Read File ^Y Prev Page ^K Cut Text ^C Cur Pos ^X Exit ^J Justify ^W Where Is ^V Next Page ^U UnCut Txt ^T ToSpell
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 128 enable Privileged Exec Mode Commands Turns on (enables) the privileged mode command set. This command does not do anything in the Privilege Executable mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax enable Parameters None Example wm3400-37FABE#enable wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 129 erase Privileged Exec Mode Commands Erases a devices file system. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax erase [cf:|flash:|nvram:|startup-config|usb1:|usb2:] Parameters erase [cf:|flash:|nvram:|startup-config|usb1:|usb2:] Example wm3400-37FABE#erase startup-config Erase startup-config? (y/n): n wm3400-37FABE# cf: Erases everything in wireless controller cf: file. flash: Erases everything in wireless controller flash: file. nvram: Erases everything in wireless controller nvram: file. startup-config Erases the wireless controllers startup configuration file. The startup configuration file is used to configure the device when it reboots. usb1: Erases everything in wireless controller usb1: file. usb2: Erases everything in wireless controller usb2: file.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 130 exit Privileged Exec Mode Commands Ends the current CLI session and closes the session window. For more information, see exit. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax exit Parameters None Example wm3400-37FABE#exit
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 131 format Privileged Exec Mode Commands Formats the devices compact flash file system Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax format cf: Parameters format cf: Example wm3400-37FABE#format cf: Warning: This will destroy the contents of compact flash. Do you want to continue [y/n]? n wm3400-37FABE# cf: Formats the compact flash file system.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 132 halt Privileged Exec Mode Commands Stops (halts) a device or a wireless controller. Once halted, the system must be restarted manually. This command stops the device immediately. No indications or notifications are provided while the device shuts down. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax halt {on <DEVICE-NAME>} Parameters halt {on <DEVICE-NAME>} Example wm3400-37FABE#halt on wm3400-37FABE wm3400-37FABE# halt {on <DEVICE-NAME>} Optional. Halts a device or a wireless controller. <DEVICE-NAME> Enter the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 133 join-cluster Privileged Exec Mode Commands Adds a wireless controller to an existing cluster of devices. Use this command to add a new wireless controller to an existing cluster. Before a wireless controller can be added to a cluster, a static address must be assigned to it. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax join-cluster <IP> user <USERNAME> password <WORD> {level|mode} join-cluster <IP> user <USERNAME> password <WORD> {level [1|2]|mode [active|stanby]} Parameters join-cluster <IP> user <USERNAME> password <WORD> {level|mode} Usage Guidelines To add a wireless controller to an existing cluster: A static IP address must be configured on the wireless controller being added. join-cluster Adds a new wireless controller to an existing cluster. <IP> Specify the IP address of the cluster member. user <USERNAME> Specify a user account with super user privileges on the new cluster member. password <WORD> Specify password for the account specified in the user parameter. level [12] Configures the routing level. 1 Configures level 1 routing. 2 Configures level 2 routing. mode [active|standby] Configures the cluster mode. active Configures cluster mode as active. standby Configures cluster mode as standby.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 134 Username and password of one of the following accounts, superuser, network admin, system admin, or operator account for the new wireless controller must be provided. Once a wireless controller is added to the cluster, a manual write memory command must be executed. Without this command, the configuration will not persist across reboots. Example wm3400-37FABE#join-cluster 172.16.10.10 user admin password admin123 Joining cluster at 172.16.10.10... Done Please execute write memory to save cluster configuration. wm3400-37FABE# Related Commands cluster Initiates the cluster context. The cluster context provides centralized management to configure all cluster members from any one member. create-cluster Creates a new cluster on a specified device.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 135 l2tpv3 Privileged Exec Mode Commands Establishes or brings down a L2TPV3 tunnel. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax l2tpv3 tunnel [<TUNNEL-NAME>|all] l2tpv3 tunnel <TUNNEL-NAME> [down|session|up] l2tpv3 tunnel <TUNNEL-NAME> [down|up] {on <DEVICE-NAME>} l2tpv3 tunnel <TUNNEL-NAME> session <SESSION-NAME> [down|up] {on <DEVICE- NAME>} l2tpv3 tunnel all [down|up] {on <DEVICE-NAME>} Parameters l2tpv3 tunnel <TUNNEL-NAME> [down|up] {on <DEVICE-NAME>} l2tpv3 tunnel <TUNNEL-NAME> session <SESSION-NAME> [down|up] {on <DEVICE- NAME>} l2tpv3 tunnel <TUNNEL-NAME> [down|up] Establishes or brings down a L2TPV3 tunnel. <TUNNEL-NAME> Specify the tunnel name. down Brings down the specified tunnel. up Establishes the specified tunnel. on <DEVICE-NAME> Optional. Establishes or brings down a tunnel on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. l2tpv3 tunnel <TUNNEL-NAME> Establishes or brings down a L2TPV3 tunnel. <TUNNEL-NAME> Specify the tunnel name.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 136 l2tpv3 tunnel all [down|up] {on <DEVICE-NAME>} Example wm3400-37FABE#l2tpv3 tunnel Tunnel1 session Tunnel1Session1 up on wm3400- 37FABE NOTE For more inofmration on the L2TPV3 tunnel configuration mode and commands, see Chapter 26. session <SESSION-NAME> [down|up] Establishes or brings down a session in the specified tunnel. <SESSION-NAME> Specify the session name. down Brings down the specified tunnel session. up Establishes the specified tunnel session. on <DEVICE-NAME> Optional. Establishes or brings down a tunnel on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. l2tpv3 tunnel <TUNNEL-NAME> Establishes or brings down a L2TPV3 tunnel. all [down|up] Establishes or brings down all L2TPV3 tunnels. down Brings down all tunnels. up Establishes all tunnels. on <DEVICE-NAME> Optional. Establishes or brings down a tunnel on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 137 logging Privileged Exec Mode Commands Modifies message logging settings Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax logging monitor {<0-7>|alerts|critical|debugging|emergencies|errors|informational| warnings|notifications} Parameters logging monitor {<0-7>|alerts|critical|debugging|emergencies|errors|informational| warnings|notifications} Example wm3400-37FABE#logging monitor warnings wm3400-37FABE# monitor Sets terminal lines logging levels. The logging severity levels can be set from 07. The system configures default settings, if no logging severity level is specified. <0-7> Optional. Enter the logging severity level from 07. The various levels and their implications are: alerts Optional. Immediate action needed (severity=1). critical Optional. Critical conditions (severity=2). debugging Optional. Debugging messages (severity=7). emergencies Optional. System is unusable (severity=0). errors Optional. Error conditions (severity=3). informational Optional.Informational messages (severity=6). notifications Optional. Normal but significant conditions (severity=5). warnings Optional. Warning conditions (severity=4).
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 138 wm3400-37FABE#logging monitor 2 wm3400-37FABE# Related Commands no Resets terminal lines logging levels
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 139 mint Privileged Exec Mode Commands Uses MiNT protocol to perform a ping and a traceroute to a remote device Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mint [ping|security|traceroute] mint ping <MINT-ID> {count <1-10000>|size <1-64000>|timeout <1-10>} mint security [approve-request [<MAC>|all]|create-security-trustpoint] mint traceroute <MINT-ID> {destination-port <1-65535>|max-hops <1-255>| source-port <1-65535>|timeout <1-255>} Parameters mint ping MINT-ID {count <1-10000>size <1-64000>timeout <1-10>} mi nt secur i t y [ appr ove- r equest [ <MAC>| al l ] | cr eat e- secur i t y- t r ust poi nt ] ping MINT-ID Sends a MiNT echo message to a MiNT destination. <MINT-ID> Specify the MiNT destination ID to ping. count <1-10000> Optional. Sets the number of times to ping the MiNT destination. <1-10000> Specify a value from 110000. The default is 3. size <1-64000> Optional. Sets the MiNT payload size in bytes. <1-64000> Specify a value from 1640000 bytes. The default is 64. timeout <1-10> Optional. Sets a response time in seconds. <1-10> Specify a value from 110 seconds. The default is 1 second. security Invokes MiNT security commands. approve request [<MAC>|all] Approves requests to join MiNT security domain. <MAC> Approves request from a specific device. Specify the MAC address of the device. all Approves all pending requests.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 140 mint traceroute MINT-ID {destination-port <1-65535>|max-hops <1-255>| source-port <1-65535>|timeout <1-255>} Example wm3400-37FABE#mint ping 70.37.FA.BF count 20 size 128 MiNT ping 70.37.FA.BF with 128 bytes of data. Response from 70.37.FA.BF: id=1 time=0.292 ms Response from 70.37.FA.BF: id=2 time=0.206 ms Response from 70.37.FA.BF: id=3 time=0.184 ms Response from 70.37.FA.BF: id=4 time=0.160 ms Response from 70.37.FA.BF: id=5 time=0.138 ms Response from 70.37.FA.BF: id=6 time=0.161 ms Response from 70.37.FA.BF: id=7 time=0.174 ms Response from 70.37.FA.BF: id=8 time=0.207 ms Response from 70.37.FA.BF: id=9 time=0.157 ms Response from 70.37.FA.BF: id=10 time=0.153 ms Response from 70.37.FA.BF: id=11 time=0.159 ms Response from 70.37.FA.BF: id=12 time=0.173 ms Response from 70.37.FA.BF: id=13 time=0.156 ms Response from 70.37.FA.BF: id=14 time=0.209 ms Response from 70.37.FA.BF: id=15 time=0.147 ms Response from 70.37.FA.BF: id=16 time=0.203 ms Response from 70.37.FA.BF: id=17 time=0.148 ms Response from 70.37.FA.BF: id=18 time=0.169 ms Response from 70.37.FA.BF: id=19 time=0.164 ms Response from 70.37.FA.BF: id=20 time=0.177 ms --- 70.37.FA.BF ping statistics --- 20 packets transmitted, 20 packets received, 0% packet loss round-trip min/avg/max = 0.138/0.177/0.292 ms create-security-trustpoint Creates a new trustpoint to use with MiNT. traceroute MINT-ID Prints the route packets trace to a device. <MINT-ID> Specify the MiNT destination ID. destination-port <1-65535> Optional. Sets the ECMP (Equal-cost Multi-path) routing destination port. <1-65535> Specify a value from 165535. The default port is 45. max-hops <1-255> Optional. Sets the maximum number of hops a traceroute packet traverses in the forward direction <1-255> Specify a value from 1255. The default is 30. source-port <1-65535> Optional.Sets the ECMP source port. <1-65535> Specify a value from 165535. The default port is 45. timeout <1-255> Optional. Sets the minimum response time period. <1-65535> Specify a value from 1255 seconds. The default is 30 seconds.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 141 mkdir Privileged Exec Mode Commands Creates a new directory in the file system Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mkdir <DIR> Parameters mkdir <DIR> Example wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 14:19:34 2012 log drwx Fri Jul 8 10:20:23 2011 test drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE wm3400-37FABE#mkdir testdir wm3400-37FABE <DIR> Specify a directory name. NOTE: A directory, specified by the <DIR> parameter, is created within the file system.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 142 wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 14:19:34 2012 log drwx Fri Jul 8 10:20:23 2011 test drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Wed Mar 21 14:24:00 2012 testdir drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 143 more Privileged Exec Mode Commands Displays contents of a file on the devices file system. This command navigates and displays specific files in the devices file system. To do so, provide the complete path to the file. The more command also displays the startup configuration file. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax more <FILE> Parameters more <FILE> Example wm3400-37FABE#more flash:/log/messages.log Mar 19 13:57:43 2012: %AUTHPRIV-4-WARNING: ipsec_starter[1308]: Starting strongSwan 4.5.0 IPsec [starter]... Mar 19 13:57:43 2012: %AUTHPRIV-4-WARNING: ipsec_starter[1308]: no default route - cannot cope with %defaultroute!!! Mar 19 13:57:43 2012: %AUTHPRIV-4-WARNING: ipsec_starter[1318]: pluto (1319) started after 500 ms Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: inserting event EVENT_REINIT_SECRET, timeout in 3600 seconds Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: including NAT- Traversal patch (Version 0.6c) Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: Changing to directory '/var/etc/ipsec.d/crls' Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: inserting event EVENT_LOG_DAILY, timeout in 36136 seconds <FILE> Specify the file name and location.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 144 Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: listening for IKE messages Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: adding interface vlan1/vlan1 172.16.10.1:500 Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: adding interface vlan1/vlan1 172.16.10.1:4500 Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: adding interface pkt0/pkt0 127.0.1.1:500 Mar 19 13:57:44 2012: %AUTHPRIV-4-WARNING: pluto[1319]: adding interface pkt0/pk --More-- wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 145 no Privileged Exec Mode Commands Use the no command to revert a command or set parameters to their default. This command is useful to turn off an enabled feature or set defaults for a parameter. The no commands have their own set of parameters that can be reset. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [adoption|captive-portal|crypto|debug|logging|page|service|terminal| upgrade|wireless] no adoption {on <DEVICE-OR-DOMAIN-NAME>} no captive-portal client [captive-portal <CAPTIVE-PORTAL-NAME>|<MAC>] {on <DEVICE-OR-DOMAIN-NAME>} no crypto pki [server|trustpoint] no crypto pki [server|trustpoint] <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} no logging monitor no page no service [cli-tables-expand|locator|mint] no service [cli-tables-expand|<MAC> no service locator {on <DEVICE-NAME} no service mint silence no terminal [length|width] no upgrade <PATCH-NAME> {on <DEVICE-NAME>} no wireless client [all|<MAC>] no wireless client all {filter|on}
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 146 no wireless client all {filter [wlan <WLAN-NAME>]} no wireless client all {on <DEVICE-OR-DOMAIN-NAME>} {filter [wlan <WLAN- NAME>]} no wireless client mac <MAC> {on <DEVICE-OR-DOMAIN-NAME>} Parameters no adoption {on <DEVICE-OR-DOMAIN-NAME>} no captive-portal client [captive-portal <CAPTIVE-PORTAL-NAME>|<MAC>] {on <DEVICE-OR-DOMAIN-NAME>} no crypto pki [server|trustpoint] <TRUSTPOINT-NAME> {del-key {on <DEVICE- NAME>}|on <DEVICE-NAME>} no logging monitor no page no adoption {on <DEVICE-OR-DOMAIN- NAME>} Resets the adoption status of a specified device or all devices. <DEVICE-OR-DOMAIN-NAME> Optional. Enter the name of the AP, wireless controller, or RF Domain. no captive-portal client Disconnects captive portal clients from the network. captive-portal <CAPTIVE-PORTAL-NAME> Disconnects captive portal clients. <CAPTIVE-PORTAL-NAME> Specify the captive portal name. <MAC> Disconnects a specified client. <MAC> Specify the MAC address of the client. on <DEVICE-OR-DOMAIN- NAME> Optional. Disconnects captive portal clients or a specified client on a specified device or RF Domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. no crypto pki Deletes all PKI authentications. [server|trustpoint] <TRUSTPOINT-NAME> Deletes PKI authentications, such as server certificates and trustpoints. server Deletes server certificates. trustpoint Deletes a trustpoint and its associated certificates. The following is common to the server and trustpoint parameters: <TURSTPOINT-NAME> Deletes a trustpoint or its server certificate. Specify the trustpoint name. del-key {on <DEVICE-NAME>} Optional. Deletes the private key associated with a server certificate or trustpoint. The operation will fail if the private key is in use by other trustpoints. on <DEVICE-NAME> Deletes the private key on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. no logging monitor Resets terminal lines message logging levels. no page Resets wireless controller paging function to its default. Disabling the page command displays the CLI command output at once, instead of page by page.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 147 no service cli-tables-expand <MAC> no service locator {on <DEVICE-NAME>} no service mint silence no upgrade <PATCH-NAME> {on <DEVICE-NAME>} no terminal [length|width] no wireless client all {filter [wlan <WLAN-NAME>]} no service Disables LEDs on a specified device in the WLAN. It also resets the CLI table expand and MiNT protocol configurations. cli-tables-expand <MAC> Disables LEDs on a specified device. <MAC> Optional. Specify the MAC address of the AP. no service Disables LEDs on a specified device in the WLAN. It also resets the CLI table expand and MiNT protocol configurations. cli-tables-expand <MAC> Disables LEDs on a specified device. <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller. no service mint silence Disables LEDs on a specified device in the WLAN. It also resets the CLI table expand and MiNT protocol configurations. mint Resets MiNT protocol configurations. Disables ping and traceroute parameters. silence Disables MiNT echo messaging and tracing of route packets. no upgrade <PATCH-NAME> Removes a patch installed on a specified device. <PATCH-NAME> Specify the name of the patch. on <DEVICE-NAME> Optional. Removes a patch on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. no terminal [length|width] Resets the width of the terminal window, or the number of lines displayed within the terminal window. length Resets the number of lines displayed on the terminal window to its default. width Resets the width of the terminal window to its default. no wireless client all Disassociates all wireless clients on a specified device or domain. filter wlan <WLAN-NAME> Optional. Specifies an additional client selection filter. wlan Filters clients based on the WLAN. <WLAN-NAME> Specify the WLAN name.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 148 no wireless client all {on <DEVICE-OR-DOMAIN-NAME>} {filter [wlan <WLAN- NAME>]} no wireless client mac <MAC> {on <DEVICE-OR-DOMAIN-NAME>} Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-37FABE#no adoption wm3400-37FABE# wm3400-37FABE#no page wm3400-37FABE# wm3400-37FABE#no service cli-tables-expand line wm3400-37FABE# Related Commands no wireless client all on <DEVICE-OR-DOMAIN-NAME> Disassociates all clients on a specified device or domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. filter wlan <WLAN-NAME> Optional. Specifies an additional client selection filter. wlan Filters clients based on the WLAN. <WLAN-NAME> Specify the WLAN name. no wireless client mac <MAC> Disassociates a single wireless client on a specified device or RF Domain mac <MAC> Specify the MAC address of the wireless client in the AA-BB- CC-DD-EE-FF format. on <DEVICE-OR-DOMAIN- NAME> Optional. Specifies the name of the AP, wireless controller, or RF Domain to which the specified client is associated. ???auto-provisioning policy??? Resets the adoption state of a device and all devices adopted to it captive-portal Manages captive portal clients debug Disables debug commands logging Modifies message logging settings page Resets wireless controller paging function to its default service Performs different functions depending on the parameter passed terminal Sets the length or the number of lines displayed within the terminal window upgrade Upgrades software image on a device wireless-client Manages wireless clients
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 149 page Privileged Exec Mode Commands Toggles wireless controller paging. Enabling this command displays the CLI command output page by page, instead of running the entire output at once. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax page Parameters None Example wm3400-37FABE#page wm3400-37FABE# Related Commands no Disables wireless controller paging
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 150 ping Privileged Exec Mode Commands Sends ICMP (Internet Controller Message Protocol) echo messages to a user-specified location Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ping <IP/HOSTNAME> {count <1-10000>|dont-fragment|size <1-64000>} Parameters ping <IP/HOSTNAME> {count <1-10000>|dont-fragment|size <1-64000>} Example wm3400-37FABE#ping 172.16.10.4 count 6 PING 172.16.10.3 (172.16.10.3): 100(128) data bytes 108 bytes from 172.16.10.4: icmp_seq=1 ttl=64 time=3.93 ms 108 bytes from 172.16.10.4: icmp_seq=2 ttl=64 time=0.367 ms 108 bytes from 172.16.10.4: icmp_seq=3 ttl=64 time=0.328 ms 108 bytes from 172.16.10.4: icmp_seq=4 ttl=64 time=0.295 ms 108 bytes from 172.16.10.4: icmp_seq=5 ttl=64 time=0.340 ms 108 bytes from 172.16.10.4: icmp_seq=6 ttl=64 time=0.371 ms <IP/HOSTNAME> Specify the destination IP address or hostname to ping. When entered without any parameters, this command prompts for an IP address or a hostname. count <1-10000> Optional. Sets the pings to the specified destination. <1-10000> Specify a value from 110000. The default is 5. dont-fragment Optional. Sets the dont-fragment bit in the ping packet. Packets with the dont- fragment bit specified, are not fragmented. When a packet, with the dont- fragment bit specified, exceeds the specified MTU (Maximum Transmission Unit) (value, an error message is sent from the device trying to fragment it. size <1-64000> Optional. Sets the ping packets size in bytes <1-64000> Specify the ping payload size from 164000 bytes. The default is 100 bytes.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 151 --- 172.16.10.3 ping statistics --- 6 packets transmitted, 6packets received, 0% packet loss round-trip min/avg/max = 0.295/0.939/3.936/1.340 ms wm3400-37FABE#
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 152 pwd Privileged Exec Mode Commands Displays the full path of the present working directory, similar to the UNIX pwd command Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax pwd Parameters None Example wm3400-37FABE#pwd flash:/ wm3400-37FABE# wm3400-37FABE#dir Directory of flash:/. drwx Fri Aug 3 13:16:52 2012 log drwx Fri Jul 8 15:50:23 2011 Final drwx Mon Jul 18 15:16:35 2011 cache drwx Thu Jul 19 08:40:19 2012 crashinfo drwx Fri Aug 3 13:14:11 2012 archived_logs drwx Sat Jan 1 05:30:25 2000 hotspot drwx Sat Jan 1 05:30:09 2000 floorplans drwx Wed May 9 20:18:19 2012 startuplog -rw- 244736 Thu Aug 16 10:05:58 2012 out.tar wm3400-37FABE#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 153 re-elect Privileged Exec Mode Commands Re-elects tunnel wireless controller. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax re-elect tunnel-controller {<WORD> {on <DEVICE-NAME>}|on <DEVICE-NAME>} Parameters re-elect tunnel-controller {<WORD> {on <DEVICE-NAME>}|on <DEVICE-NAME>} Example wm3400-37FABE#re-elect tunnel-controller OK wm3400-37FABE# re-elect tunnel-controller Re-elects tunnel wireless controller. <WORD> {on <DEVICE- NAME>} Optional. Re-elects tunnel wireless controller on all devices whose preferred tunnel wireless controller name matches <WORD>. on <DEVICE-NAME> Optional. Re-elects tunnel wireless controller on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Re-elects tunnel wireless controller on a specified device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 154 reload Privileged Exec Mode Commands Halts the wireless controller and performs a warm reboot of the device Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax reload {cancel|force|in|on} reload {on <DEVICE-OR-DOMAIN-NAME>} reload {cancel|force} {on <DEVICE-OR-DOMAIN-NAME>} reload {in <1-999>} {list|on} reload {in <1-999>} {list {<LINE>|all}|on <DEVICE-OR-DOMAIN-NAME>} reload {in <1-999>} {on <DEVICE-OR-DOMAIN-NAME>} Parameters reload {on <DEVICE-OR-DOMAIN-NAME>} reload {cancel|force} {on <DEVICE-OR-DOMAIN-NAME>} on <DEVICE-OR-DOMIN- NAME> Optional. Performs reload on an AP, wireless controller, or RF Domain. Halts a system and performs a warm reboot <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. cancel Optional. Cancels pending reloads. force Optional. Forces reboot, while ignoring conditions like upgrade in progress, unsaved changes, etc. on <DEVICE-OR-DOMAIN- NAME> Optional. Cancels or forces a reload on an a specified device. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or the RF Domain.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 155 reload {in} <1-999> {list {<LINE>|all}|on <DEVICE-OR-DOMAIN-NAME>} Example wm3400-37FABE#reload force on wm3400-37FABE wm3400-37FABE# in <1-9999> Schedules a reload after a specified time period. <1-9999> Specify the time from 1999 minutes. list {<LINE>|all} Optional. Reloads all adopted devices or specified devices. <LINE> Optional. Reloads listed devices. List all devices (to be reloaded) separated by a space. all Optional. Reloads all devices adopted by this wireless controller. on <DEVICE-OR-DOMAIN- NAME> Optional. Reloads on a specified device. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 156 remote-debug Privileged Exec Mode Commands Troubleshoots remote systems. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax remote-debug [clear-crashinfo|copy-crashinfo|copy-smartrf-report|copy- techsupport|end-session|live-pktcap|more|offline-pktcap|wireless] remote-debug [clear-crashinfo|copy-crashinfo|copy-techsupport|live- pktcap|more|offline-pktcap|wireless] [hosts <REMOTE-DEVICE-NAME>|rf- domain <RF-DOMAIN-NAME>]write <URL> remote-debug copy-smartrf-report rf-domain <RF-DOMAIN-NAME> write <URL> remote-debug end-session [copy-crashinfo|copy-smartrf-report|copy- techsupport|live-pktcap|more|offline-pktcap|wireless] Parameters remote-debug [clear-crashinfo|copy-crashinfo|copy-techsupport|live- pktcap|more|offline-pktcap|wireless] [hosts <REMOTE-DEVICE-NAME>|rf-domain <RF-DOMAIN-NAME>]write <URL> remote-debug Invokes remote system debugging commands. clear-crashinfo Clears crash info files on a remote system. copy-crashinfo Copies all crash info files from /flash/crashinfo. copy-techsupport Copies extensive system information useful to technical support for troubleshooting. live-pktcap Enables live packet capture. more Displays contents of a file. offline-pktcap Captures packets and transfers packet capture data upon completion wireless Captures wireless debug messages
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 157 remote-debug copy-smartrf-report rf-domain <RF-DOMAIN-NAME> write <URL> remote-debug end-session [copy-crashinfo|copy-smartrf-report|copy- techsupport|live-pktcap|more|offline-pktcap|wireless] Example wm3400-37FABE#reload force on wm3400-37FABE wm3400-37FABE# hosts <REMOTE-DEVICE-NAME> Performs selected action on specified remote device(s). <REMOTE-DEVICE-NAME> Specify remote systems name (or multiple names separated by space). rf-domain <RF-DOMAIN-NAME> Performs selected actions on a specified RF Domain. <RF-DOMAIN-NAME> Specify the RF Domain name. write <URL> Copies the selected information to a directory. <URL> Specify the directory path in the following format: tftp://<hostname|IP>[:port]/path/ ftp://<user>:<passwd>@<hostname|IP>[:port]/path/ usb1:/path usb2:/path cf:/path remote-debug Invokes remote system debugging commands. copy-smartrf-report Copies Smart RF report. rf-domain <RF-DOMAIN-NAME> Copies Smart RF report for a specified RF Domain. <RF-DOMAIN-NAME> Specify the RF Domain name.. write <URL> Copies the selected information to a directory. <URL> Specify the directory path in the following format: tftp://<hostname|IP>[:port]/path/ ftp://<user>:<passwd>@<hostname|IP>[:port]/path/ usb1:/path usb2:/path cf:/path remote-debug Invokes remote system debugging commands. end-session Ends an in-progress debugging session.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 158 rename Privileged Exec Mode Commands Renames a file in the devices file system. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rename <OLD-FILE-NAME> <NEW-FILE-NAME> Parameters rename <OLD-FILE-NAME> <NEW-FILE-NAME> Example wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 14:19:34 2012 log drwx Fri Jul 8 10:20:23 2011 test drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Wed Mar 21 14:24:00 2012 testdir drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE# wm3400-37FABE#rename flash:/test/ Final wm3400-37FABE#dir Directory of flash:/. <OLD-FILE-NAME> Specify the file to rename <NEW-FILE-NAME> Specify the new file name
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 159 drwx Wed Mar 21 14:19:34 2012 log drwx Fri Jul 8 10:20:23 2011 Final drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Wed Mar 21 14:24:00 2012 testdir drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE#
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 160 rmdir Privileged Exec Mode Commands Deletes an existing directory from the file system (only empty directories can be removed) Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rmdir <DIR> Parameters rmdir <DIR> Example wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 14:19:34 2012 log drwx Fri Jul 8 10:20:23 2011 Final drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Wed Mar 21 14:24:00 2012 testdir drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar wm3400-37FABE# wm3400-37FABE#dir Directory of flash:/. drwx Wed Mar 21 14:19:34 2012 log rmdir <DIR> Specifies the directory name.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 161 drwx Fri Jul 8 10:20:23 2011 Final drwx Mon Jul 18 09:46:35 2011 cache drwx Tue Mar 20 10:11:09 2012 crashinfo drwx Sat Jan 1 00:00:25 2000 hotspot drwx Sat Jan 1 00:00:09 2000 floorplans drwx Mon Mar 19 13:57:43 2012 startuplog -rw- 373760 Thu Mar 15 12:15:07 2012 out.tar
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 162 self Privileged Exec Mode Commands Displays the logged devices configuration context Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax self Parameters None Example wm3400-37FABE#self Enter configuration commands, one per line. End with CNTL/Z. wm3400-37FABE(config-device-00-15-70-37-FA-BE)#
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 163 ssh Privileged Exec Mode Commands Opens an SSH (Secure Shell) connection between two network devices. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ssh <IP/HOSTNAME> <USERNAME> Parameters ssh [<IP/HOSTNAME>] [<USERNAME>] Usage Guidelines To exit of the other devices context, use the command that is relevant to that device. Example wm3400-37FABE#ssh 172.16.10.8 admin [email protected] password: wm3400-37FABE> <IP>/<HOSTNAME> Specify the IP address or hostname of the remote system. <USERNAME> Specify the name of the user requesting the SSH connection.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 164 telnet Privileged Exec Mode Commands Opens a Telnet session between two network devices Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax telnet <IP> {<TCP-PORT>} Parameters telnet <IP> {<TCP-PORT>} Usage Guidelines To exit of the other devices context, use the command relevant to that device. Example WM3700-37FABE#telnet 172.16.10.4 Entering character mode Escape character is '^]'. WM3600 release 5.2.6.0-014D WM3600-380649 login: admin Password: WM3600-380649> <IP> Configures the remote systems IP address. The Telnet session will be established between the connecting system and the remote system. <IP> Specify the remote system IP address. <TCP-PORT> Optional. Specify the TCP (Transmission Control Protocol) port.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 165 terminal Privileged Exec Mode Commands Sets the number of characters per line, and the number of lines displayed within the terminal window. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax terminal [length|width] <0-512> Parameters terminal [length|width] <0-512> Example wm3400-37FABE#terminal length 150 wm3400-37FABE# wm3400-37FABE#terminal width 215 wm3400-37FABE# Related Commands length <0-512> Sets the number of lines displayed on a terminal window. <0-512> Specify a value from 0512. width <0-512> Sets the width or number of characters displayed on the terminal window. <0-512> Specify a value from 0512. no Resets the width of the terminal window or the number of lines displayed on a terminal window
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 166 time-it Privileged Exec Mode Commands Verifies the time taken by a particular command between request and response Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax time-it <COMMAND> Parameters time-it <COMMAND> Example wm3400-37FABE#time-it config terminal Enter configuration commands, one per line. End with CNTL/Z. That took 0.00 seconds.. wm3400-37FABE# time-it <COMMAND> Verifies the time taken by a particular command to execute and provide a result. <COMMAND> Specify the command to time execution.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 167 traceroute Privileged Exec Mode Commands Traces the route to a defined destination. Use --help or -h to display a complete list of parameters for the traceroute command Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax traceroute <LINE> Parameters traceroute <LINE> Example wm3400-37FABE#traceroute 172.16.10.2 traceroute to 172.16.10.2 (172.16.10.2), 30 hops max, 38 byte packets 1 172.16.10.1 (172.16.10.1) 3002.008 ms !H 3002.219 ms !H 3003.945 ms !H wm3400-37FABE# <LINE> Traces route to a destination IP address or hostname. <LINE> Specify a traceroute argument. For example, service traceroute-h.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 168 upgrade Privileged Exec Mode Commands Upgrades software image on a device. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax upgrade [<FILE>|<URL>] {background|on <DEVICE-NAME>} Parameters upgrade [<FILE>|<URL>] {background|on <DEVICE-NAME>} Example wm3400- 37FABE#upgr ade t f t p: / / 157. 235. 208. 105: / i mg var 2 i s 10 per cent f ul l / t mp i s 2 per cent f ul l <FILE> Specify the target firmware image location in the following format: cf:/path/file usb1:/path/file usb2:/path/file <URL> Specify the target firmware image location in the following format: tftp://<hostnameIP>[:port]/path/file ftp://<user>:<passwd>@<hostnameIP>[:port]/path/file sftp://<user>:<passwd>@<hostnameIP>[:port]>/path/file http://<hostnameIP>[:port]/path/file cf:/path/file usb<n>:/path/file background Optional. Performs upgrade in the background. on <DEVICE-NAME> Optional. Upgrades the software image on a remote AP or wireless controller. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 169 Fr ee Memor y 161896 kB FWU i nvoked vi a Li nux shel l Running from partition /dev/hda5, partition to wm3400-37FABE#upgrade tftp://157.125.208.235/img Running from partition /dev/mtdblock7, partition to update is /dev/ mtdblock6 Related Commands no Removes a patch installed on a specified device
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 170 upgrade-abort Privileged Exec Mode Commands Aborts an ongoing software image upgrade Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax upgrade-abort {on <DEVICE-OR-DOMAIN-NAME>} Parameters upgrade-abort {on <DEVICE-OR-DOMAIN-NAME>} Example wm3400-37FABE#upgrade-abort on wm3400-37FABE Error: No upgrade in progress wm3400-37FABE# upgrade-abort Aborts an ongoing software image upgrade. on <DEVICE-OR-DOMAIN- NAME> Optional. Aborts an ongoing software image upgrade on a specified device. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 171 watch Privileged Exec Mode Commands Repeats a specified CLI command at periodic intervals Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax watch <1-3600> <LINE> Parameters watch <1-3600> <LINE> Example wm3400-37FABE#watch 1 show clock wm3400-37FABE# watch <1-3600> Repeats a CLI command at a specified interval. <1-3600> Select an interval from 13600 seconds. Pressing CTRL-Z halts execution of the command. <LINE> Specify the CLI command name.
Chapter 4: Privileged Exec Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 172
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 173 C H A P T E R 5 Global Configuration Commands This chapter summarizes the global-configuration commands in the CLI command structure. The term global indicates characteristics or features effecting the system as a whole. Use the Global Configuration Mode to configure the system globally, or enter specific configuration modes to configure specific elements (such as interfaces or protocols). Use the configure terminal command (under PRIV EXEC) to enter the global configuration mode. The example below describes the process of entering the global configuration mode from the privileged EXEC mode: wm3700-37FABE# configure terminal wm3700-37FABE(config)# NOTE The system prompt changes to indicate you are now in the global configuration mode. The prompt consists of the device host name followed by (config) and a pound sign (#). Commands entered in the global configuration mode update the running configuration file as soon as they are entered. However, these changes are not saved in the startup configuration file until a commit write memory command is issued. wm3700-37FABE(config)#? Global Configuration commands: aaa-policy Configure an authentication/accounting/authorization policy aaa-tacacs-policy Configure an authentication/accounting/authorization TACACS policy advanced-wips-policy Configure a advanced-wips policy AP4021 AP4021 access point AP4022 AP4022 access point AP4600 AP4600 access point AP4511 AP4511 access point AP4521 AP4521 access point AP4522 AP4522 access point AP4532 AP4532 access point AP4700 AP4700 access point association-acl-policy Configure an association acl policy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 174 auto-provisioning-policy Configure an auto-provisioning policy captive-portal Configure a captive portal clear Clear customize Customize the output of summary cli commands device Configuration on multiple devices device-categorization Configure a device categorization object dhcp-server-policy DHCP server policy dns-whitelist Configure a whitelist event-system-policy Configure a event system policy firewall-policy Configure firewall policy help Description of the interactive help system host Enter the configuration context of a device by specifying its hostname igmp-snoop-policy Create igmp snoop policy inline-password-encryption Store encryption key in the startup configuration file ip Internet Protocol (IP) l2tpv3 L2tpv3 tunnel protocol mac MAC configuration management-policy Configure a management policy meshpoint Create a new MESHPOINT or enter MESHPOINT configuration context for one or more meshpoint-qos-policy Configure a meshpoint quality-of-service policy mint-policy Configure the global mint policy nac-list Configure a network access control list no Negate a command or set its defaults password-encryption Encrypt passwords in configuration profile Profile related commands - if no parameters are given, all profiles are selected radio-qos-policy Configure a radio quality-of-service policy radius-group Configure radius user group parameters radius-server-policy Create device onboard radius policy radius-user-pool-policy Configure Radius User Pool rf-domain Create a RF Domain or enter rf-domain context for one or more rf-domains WM3400 WM3400 wireless controller WM3600 WM3600 wireless controller WM3700 WM3700 wireless controller routing-policy Policy Based Routing Configuration role-policy Role based firewall policy self Config context of the device currently logged into smart-rf-policy Configure a Smart-RF policy wips-policy Configure a wips policy wlan Create a new WLAN or enter WLAN configuration context for one or more WLANs wlan-qos-policy Configure a wlan quality-of-service policy write Write running configuration to memory or terminal clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 175 revert Revert changes service Service Commands show Show running system information wm3700-37FABE(config)# Global Configuration Commands The following table summarizes Global Configuration commands. Command Description Reference aaa-policy Configures a AAA policy page 5-177 ???aaa-tacacs- policy??? Configures an advanced WIPS policy. ??? advanced-wips- policy Configures an advanced WIPS policy page 5-181 ap4021 Adds a AP4021 to the wireless controller managed network page 5-183 ap4022 Adds a AP4022 to the wireless controller managed network page 5-184 ap4600 Adds a AP4600 series AP to the wireless controller managed network page 5-185 ap4511 Adds a AP4511 to the wireless controller managed network page 5-186 ap4521 Adds a AP4521 to the wireless controller managed network page 5-187 ??ap4522?? Adds a AP4522 to the wireless controller managed network ??? ap4532 Adds a AP4532 to the wireless controller managed network page 5-189 ap47xx Adds a AP4700 series AP to the wireless controller managed network page 5-190 association-acl- policy Configures an association ACL policy page 5-191 auto-provisioning- policy Configures an auto provisioning policy page 5-193 captive portal Configures a captive portal page 5-195 clear Clears the event history page 5-217 critical-resource- policy Configures a critical resource policy page 5-218 customize Customizes the CLI command summary output page 5-222 device Specifies configuration on multiple devices page 5-229 device- categorization Configures a device categorization object page 5-231 dhcp-server-policy Configures a DHCP server policy page 5-236 dns-whitelist Configures a DNS whitelist page 5-237 do Runs commands from the EXEC mode page 5-241 event-system- policy Configures an event system policy page 5-254 firewall-policy Configures a firewall policy page 5-276 host Sets the system's network name page 5-277 ???inline-password- encryption??? Stores the encryption key in the startup configuration file page 5-278 ip Configures IP (Internet Protocol) components page 5-280
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 176 l2tpv3 Configures L2TPv3 (Layer 2 Tunneling Protocol Version 3) tunnel policy page 5-282 mac Configures MAC access lists (goes to the MAC Access Control List [ACL] mode) page 5-284 management-policy Configures a management policy page 5-286 ???meshpoint??? Configures meshpoint related configuration commands ??? ???meshpoint-qos- policy??? Configures a set of parameters that defines the QoS (Quality of Service) mint-policy Configures a MiNT security policy page 5-287 nac-list Configures a network ACL page 5-288 no Negates a command or sets its default page 5-293 password- encryption Enables password encryption page 5-295 profile Configures profile related commands page 5-296 radio-qos-policy Configures a radio qos policy page 5-300 radius-group Configures a RADIUS group page 5-301 radius-server-policy Configures a RADIUS server policy page 5-302 radius-user-pool- policy Configures a RADIUS user pool policy page 5-303 rf-domain Creates a RF Domain page 5-304 wm3400 Adds a WM3400 wireless controller to a network page 5-325 wm3600 Adds a WM3600 wireless controller to a network page 5-326 wm3700 Adds a WM3700 wireless controller to a network page 5-327 ???wm3950??? Adds a WM3950 wireless controller to a network ??? role-policy Configures a role policy page 5-328 ???routing-policy??? Configures a routing policy ??? self Displays a logged devices configuration context page 5-329 smart-rf-policy Configures a Smart RF policy page 5-330 wips-policy Configures a WIPS policy page 5-331 wlan Configures a wireless WLAN page 5-332 wlan-qos-policy Configures a WLAN QoS policy page 5-377 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 177 aaa-policy Global Configuration Commands Configures an AAA (Authentication, Accounting, and Authorization) policy. This policy configures multiple servers for authentication and authorization. Up to six servers can be configured for providing AAA services. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax aaa-policy <AAA-POLICY-NAME> Parameters aaa-policy <AAA-POLICY-NAME> Example wm3700-37FABE(config)#aaa-policy test wm3700-37FABE(config-aaa-policy-test)#? AAA Policy Mode commands: accounting Configure accounting parameters attribute Configure RADIUS attributes in access and accounting requests authentication Configure authentication parameters health-check Configure server health-check parameters mac-address-format Configure the format in which the MAC address must be filled in the Radius-Request frames no Negate a command or set its defaults proxy-attribute Configure radius attribute behavior when proxying through controller or rf-domain-manager server-pooling-mode Configure the method of selecting a server from the pool of configured AAA servers use Set setting to use <AAA-POLICY-NAME> Specify the AAA policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 178 clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-aaa-policy-test)# Related Commands NOTE For more information on the AAA policy commands, see Chapter 9, AAA Policy. no Removes an existing AAA policy.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 179 aaa-tacacs-policy Global Configuration Commands Configures AAA Terminal Access Controller Access-Control System (TACACS) policy. This policy configures multiple servers for authentication and authorization. A TACACS Authentication server should be configured when the server preference is authenticated server.Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax aaa-tacacs-policy <AAA-TACACS-POLICY-NAME> Parameters aaa-tacacs-policy <AAA-TACACS-POLICY-NAME> Example wm3700-37FABE(config)#aaa--tacacs-policy testpolicy wm3700-37FABE(config-aaa--tacacs-policy-testpolicy)#? AAA TACACS Policy Mode commands: accounting Configure accounting parameters authentication Configure authentication parameters authorization Configure authorization parameters no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal <AAA-TACACS-POLICY-NAME> Specify the AAA-TACACS policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 180 wm3700-37FABE(config-aaa--tacacs-policy-testpolicy)# Related Commands NOTE For more information on the AAA policy commands, see Chapter 29, AAA-TACACS Policy. no Removes an existing AAA TACACS policy
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 181 advanced-wips-policy Global Configuration Commands Configures advanced WIPS (Wireless Intrusion Prevention System) policy parameters. The WIPS prevents unauthorized access to a managed network. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax advanced-wips-policy <ADVANCED-WIPS-POLICY-NAME> Parameters advanced-wips-policy <ADVANCED-WIPS-POLICY-NAME> Example wm3700-37FABE(config)#advanced-wips-policy test wm3700-37FABE(config-advanced-wips-policy-test)# Advanced WIPS policy Mode commands: event Configure event detection no Negate a command or set its defaults server-listen-port Configure local WIPS server listen port number terminate Add a device to the list of devices to be terminated use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands <ADVANCED-WIPS- POLICY-NAME> Specify the advanced WIPS policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 182 show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-advanced-wips-policy test)# Related Commands NOTE For more information on WIPS, see Chapter 11, Advanced WIPS Policy. no Removes an exsiting Advanced WIPS policy.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 183 ap4021 Global Configuration Commands Adds a AP4021 access point to the wireless controller managed network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4021 <MAC> Parameters ap4021 <MAC> Example wm3700-37FABE(config)#ap4021 11-22-33-44-55-66 ? wm3700-37FABE(config-device-11-22-33-44-55-66)# wm3700-37FABE(config)#show wireless ap configured +----+---------------+-------------------+------------------+-------------- |IDX | NAME | MAC | PROFILE | RF-DOMAIN | +----+---------------+-------------------+------------------+-------------- | 1 | AP4731-889EC4 | 00-15-70-88-9E-C4 | default-AP4731 | default | | 2 | AP4021-23456 | 11-22-33-44-55-66 | default-AP4021 | default | +----+---------------+-------------------+------------------+-------------- wm3700-37FABE(config)# Related Commands <MAC> Specify the MAC address of the AP4021. no Removes an AP4021 from the network.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 184 ap4022 Global Configuration Commands Adds a AP4022 access point to the wireless controller managed network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4022 <MAC> Parameters ap4022 <MAC> Example WM3700-37FABE(config)#ap4022 11-22-33-44-55-66 ? WM3700-37FABE(config-device-11-22-33-44-55-66)# WM3700-37FABE(config)#show wireless ap configured +----+---------------+-------------------+------------------+-------------- |IDX | NAME | MAC | PROFILE | RF-DOMAIN | +----+---------------+-------------------+------------------+-------------- | 1 | AP4731-889EC4 | 00-15-70-88-9E-C4 | default-AP4731 | default | | 2 | AP4022-23456 | 11-22-33-44-55-66 | default-AP4022 | default | +----+---------------+-------------------+------------------+-------------- WM3700-37FABE(config)# Related Commands <MAC> Specify the MAC address of the AP4022. no Removes an AP4022 from the network.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 185 ap4600 Global Configuration Commands Adds a AP4600 access point to the wireless controller managed network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4600 <MAC> Parameters ap4600 <MAC> Example WM3700-37FABE(config)#ap4600 11-22-33-44-55-66 ? WM3700-37FABE(config-device-11-22-33-44-55-66) WM3700-37FABE(config)#show wireless ap configured +-----+---------------+-------------------+-----------------+-------------- | IDX | NAME | MAC | PROFILE | RF-DOMAIN | +-----+---------------+-------------------+-----------------+-------------- | 1 | AP4731-889EC4 | 00-15-70-88-9E-C4 | default-AP4731 | default | | 2 | AP4600-445566 | 11-22-33-44-55-66 | default-AP4600 | default | +-----+---------------+-------------------+-----------------+-------------- WM3700-37FABE(config)# Related Commands <MAC> Specify the MAC address of the AP4600. no Removes an AP4600 from the network.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 186 ap4511 Global Configuration Commands Adds a AP4511 access point to the wireless controller network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4511 <MAC> Parameters ap4511 <MAC> Example wm3700-37FABE(config)#ap4511 00-17-70-88-9E-C4 ? wm3700-37FABE(config-device-00-17-70-88-9E-C4)# Related Commands <MAC> Specify the MAC address of the AP4511. no Removes an AP4511 from the network.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 187 ap4521 Global Configuration Commands Adds a AP4521 access point to the wireless controller network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4521 <MAC> Parameters ap4521 <MAC> Example wm3700-37FABE(config)#AP4521 77-88-99-01-F0-AB ? wm3700-37FABE(config-device-77-88-99-01-F0-AB)# Related Commands <MAC> Specify the MAC address of the AP4521. no Removes an AP4521 from the network.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 188 ap4522 Global Configuration Commands Adds a AP4522 access point to the wireless controller network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4522 <MAC> Parameters ap4522 <MAC> Example wm3700-37FABE(config)#AP4522 77-88-99-01-F0-AB ? wm3700-37FABE(config-device-77-88-99-01-F0-AB)# Related Commands <MAC> Specify the MAC address of the AP4522. no Removes an AP4522 from the network.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 189 ap4532 Global Configuration Commands Adds a AP4532 access point to the wireless controller network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap4532 <MAC> Parameters ap4532 <MAC> Example wm3700-37FABE(config)#AP4532 00-27-70-89-9F-E4 ? wm3700-37FABE(config-device-00-27-70-89-9F-E4)# Related Commands <MAC> Specify the MAC address of the AP4532. no Removes an AP4532 from the network.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 190 ap47xx Global Configuration Commands Adds an AP4700 series access point to the wireless controller network. If a profile for the AP is not available, a new profile is created. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap47xx <MAC> Parameters ap47xx <MAC> Example wm3700-37FABE(config)#AP4700 00-15-70-88-9E-C4 wm3700-37FABE(config-device-00-15-70-88-9E-C4)# Related Commands <MAC> Specify the MAC address of the AP4700. no Removes an AP47xx from the network.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 191 association-acl-policy Global Configuration Commands Configures an association ACL policy. This policy configures a list of devices allowed or denied access to the wireless controller managed network. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax association-acl-policy <ASSOCIATION-ACL-POLICY-NAME> Parameters association-acl-policy <ASSOCIATION-ACL-POLICY-NAME> Example wm3700-37FABE(config)#association-acl-policy test wm3700-37FABE(config-assoc-acl-test)# Association ACL Mode commands: deny Specify MAC addresses to be denied no Negate a command or set its defaults permit Specify MAC addresses to be permitted clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal <ASSOCIATION-ACL- POLICY-NAME> Specify the association ACL policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 192 wm3700-37FABE(config-assoc-acl-test)# Related Commands NOTE For more information on the association-acl-policy, see Chapter 12, Association ACL Policy. no Resets values or disables commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 193 auto-provisioning-policy Global Configuration Commands Configures an auto provisioning policy. This policy is used to configure the automatic provisioning of device adoption. The policy configures how an AP is adopted based on its type. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax auto-provisioning-policy <AUTO-PROVISIONING-POLICY> Parameters auto-provisioning-policy <AUTO-PROVISIONING-POLICY> Example wm3700-37FABE(config)#auto-provisioning-policy test wm3700-37FABE(config-auto-provisioning-policy-test)# Auto-Provisioning Policy Mode commands: adopt Add rule for device adoption default-adoption Adopt devices even when no matching rules are found. Assign default profile and default rf-domain deny Add rule to deny device adoption no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands <AUTO-PROVISIONING- POLICY> Specify the auto provisioning policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 194 show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-auto-provisioning-policy-test)# Related Commands NOTE For more information on the association-acl-policy, see Chapter 10, Auto Provisioning Policy. no Removes an existing auto-provisioning policy.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 195 captive portal Global Configuration Commands The captive portal mode configures a hotspot. The following table lists the command to enter the captive portal configuration mode. captive-portal captive portal Configures a captive portal. A captive portal is a hotspot type guest WLAN where users access wireless controller resources. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax captive-portal <CAPTIVE-PORTAL> Parameters captive-portal <CAPTIVE-PORTAL> Command Description Reference captive-portal Configures captive portal Web page parameters page 5-195 captive-portal- mode commands Summarizes captive portal configuraiton commands page 5-197 <CAPTIVE-PORTAL> Specify the captive portal name. If the captive portal does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 196 Example wm3700-37FABE(config)#captive-portal testportal wm3700-37FABE(config-captive-portal-testportal)# Captive Portal Mode commands: access-time Allowed access time for the client. Used when there is no session time in radius response access-type Access type of this captive portal accounting Configure how accounting records are created for this captive portal policy connection-mode Connection mode for this captive portal custom-auth Custom user information data-limit Enforce data limit for clients inactivity-timeout Inactivity timeout in seconds. If a frame is not received from client for this amount of time, then current session will be removed logout-fqdn Configure the FQDN address to logout the session from client no Negate a command or set its defaults server Configure captive portal server parameters simultaneous-users Particular username can only be used by a certain number of MAC addresses at a time terms-agreement User needs to agree for terms and conditions use Set setting to use webpage Configure captive portal webpage parameters webpage-auto-upload Enable automatic upload of advanced webpages webpage-location The location of the webpages to be used for authentication. These pages can either be hosted on the system or on an external web server. clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-captive-portal-testportal)# Related Commands no Removes an existing captive potal.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 197 captive-portal-mode commands The following table summarizes captive portal mode commands Command Description Reference access-time Defines a clients access time. It is used when no session time is defined in the RADIUS response page 5-198 access-type Configures a captive portals access type page 5-199 accounting Enables a captive portals accounting records page 5-200 connection-mode Configures a captive portals connection mode page 5-201 inactivity-timeout Configures custom user information page 5-205 ???data-limit??? Enforces data limit on captive portal clients ??? inactivity-timeout Defines an inactivity timeout in seconds page 5-205 l???ogout-fqdn??? Clears the logout FQDN address ??? no Resets or disables captive portal commands page 5-205 server Configures the captive portal server parameter page 5-209 simultaneous- users Specifies a username used by a MAC address pool page 5-210 terms-agreement Enforces the user to agree to terms and conditions (included in login page) for captive portal access page 5-211 use Defines captive portal configuration settings page 5-212 webpage Configures captive portal web page parameters page 5-214 ???webpage-auto- upload??? Enables automatic uploads of advanced web pages on a captive portal ??? webpage-location Specifies the location of web pages used for captive portal authentication page 5-213 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 198 access-time captive-portal-mode commands Defines the permitted access time for a client. It is used when no session time is defined in the RADIUS response. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax access-time <30-10080> Parameters access-time <30-10080> Example wm3700-37FABE(config-captive-portal-test)#access-time 35 wm3700-37FABE(config-captive-portal-test)#show context captive-portal test access-time 35 wm3700-37FABE(config-captive-portal-test)# Related Commands <30-10080> Defines the access time allowed for a wireless client from 3010080 minutes no Removes the permitted access time for a client.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 199 access-type captive-portal-mode commands Defines the captive portal access type. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax access-type [custom-auth-radius|logging|no-auth|radius|self-registration] access-type self-registration user-pool <RAD-USER-POOL-NAME> group-name <GROUP-NAME> Parameters access-type [custom-auth-radius|logging|no-auth|radius|self-registration] access-type self-registration user-pool <RAD-USER-POOL-NAME> group-name <GROUP-NAME> custom-auth-radius Verifies custom user information for authentication (RADIUS lookup of given information, including, e-mail address, telephone, etc.). logging Generates a logging record of users and allowed access. no-auth Configures a no authentication required for a guest (redirected to welcome message). radius Enables RADIUS authentication for wireless clients. self-registration Allows guest self registration once redirected to the login page. user-pool <RAD-USER-POOL-NAME> Specifies the RADIUS user pool to which the self registered user is added. <RAD-USER-POOL-NAME> Specify the RADIUS user pool name. group-name <GROUP-NAME> Specifies the group, within the specified user pool, to which the self registered user is added. <GROUP-NAME> Specify the group name.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 200 Example wm3700-37FABEE(config-captive-portal-test)#access-type logging wm3700-37FABE(config-captive-portal-test)#show context captive-portal test access-type logging access-time 35 wm3700-37FABE(config-captive-portal-test)# Related Commands accounting captive-portal-mode commands Enables accounting records for a captive portal. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accounting [radius|syslog] accounting radius accounting syslog host <IP/HOSTNAME> {port <1-65535>} Parameters accounting radius no Removes the captive portal access type. radius Enables support for RADIUS accounting messages.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 201 accounting syslog host <IP/HOSTNAME> {port <1-65535>} Example wm3700-37FABE(config-captive-portal-test)#accounting syslog host 172.16.10.13 port 1 wm3700-37FABE(config-captive-portal-test)#show context captive-portal test access-type logging access-time 35 accounting syslog host 172.16.10.13 port 1 wm3700-37FABE(config-captive-portal-test)# Related Commands connection-mode captive-portal-mode commands Configures a captive portals connection mode. HTTP uses plain unsecured connection for user requests. HTTPS uses encrypted connection to support user requests. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax connection-mode [http|https] syslog host <IP/HOSTNAME> Enables support for syslog accounting messages. host <IP/HOSTNAME> Specifies the syslog server host address. Specify the IP address or hostname of the syslog server. port <1-65535> Optional. Specifies the syslog servers listener port. <1-65535> Specify the UDP port from 165535. no Disables accounting records for this captive portal.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 202 Parameters connection-mode [http|https] Example wm3700-37FABE(config-captive-portal-test)#connection-mode https wm3700-37FABE(config-captive-portal-test)#show context access-type logging access-time 35 connection-mode https accounting syslog host 172.16.10.13 port 1 wm3700-37FABE(config-captive-portal-test)# Related Commands custom-auth captive-portal-mode commands Configures custom user information when authenticating with the RADIUS server. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax custom-auth info <LINE> http Sets HHTP as the default connection mode. https Sets HHTPS as the default connection mode. NOTE: HTTPS is a more secure version of HTTP, and uses encryption while sending and receiving requests. no Removes the captive portals connection mode.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 203 Parameters custom-auth info <LINE> Example wm3700-37FABE(config-captive-portal-test)#custom-auth info testuser [email protected] wm3700-37FABE(config-captive-portal-test)#show context captive-portal test access-type logging access-time 35 custom-auth info testuser,\ [email protected] connection-mode https accounting syslog host 172.16.10.13 port 1 wm3700-37FABE(config-captive-portal-testportal)# Related Commands data-limit captive-portal-mode commands Enforces data transfer limits on captive portal clients. This feature enables the tracking and logging of user usage. Users exceeding the allowed bandwidth are restricted from the captive portal. info <LINE> Configures information used for RADIUS lookup when custom-auth radius access type is configured. <LINE> Guest data needs to be provided. Specify the name, e-mail address and telephone number of the user. no Removes custom user information configured with this captive portal.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 204 Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax data-limit <1-102400> {action [log-and-disconnect|log-only]} Parameters data-limit <1-102400> {action [log-and-disconnect|log-only]} Example wm3700-37FABE(config-captive-portal-test)##dat a- l i mi t 200 act i on l og- and- di sconnect wm3700-37FABE(config-captive-portal-test)# wm3700-37FABE(config-captive-portal-test)#show context captive-portal test data-limit 200 action log-and-disconnect access-time 35 wm3700-37FABE(config-captive-portal-testportal)# data-limit <1-102400> Sets a captive portal clients data transfer limit in megabytes. This limit is applicable for both upstream and downstream data transfer. <1-102400> Specify a value from 1102400 MB. action [log-and-disconnect| log-only] Optional. Specifies the action taken when a client exceeds the configured data limit. The options are: log-and-disconnect Logs a record and disconnects the client. log-only Only a log is generated and the client remains connected to the captive portal.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 205 Related Commands inactivity-timeout captive-portal-mode commands Defines an inactivity timeout in seconds. If a frame is not received from a client for the specified time interval, the current session is terminated. Supported on the following platforms: AP4021 AP4022 AP4600 AP4511 AP4521 AP4522 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax inactivity-timeout <300-1800> Parameters inactivity-timeout <300-1800> Example wm3700-37FABE(config-captive-portal-test)#inactivity-timeout 750 wm3700-37FABE(config-captive-portal-test)# Related Commands no captive-portal-mode commands no Removes data limit enforcement for captive portal clients. <300-1800> Defines the duration of inactivity after which a captive portal session is automatically terminated. Set a timeout interval from 3001800 seconds. no Resets or disables captive portal commands
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 206 The no command disables captive portal mode commands or resets parameters to their default. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [access-time|access-type|accounting|connection-mode|custom-auth| inactivity-timeout|server|simultaneous-users|terms- agreement|use|webpage| webpage-location] no [access-time|access-type|connection-mode|inactivity- timeout|simultaneous-users| terms-agreement|webpage-location] no accounting [radius|syslog] no custom-auth info no server host no server mode {centralized-controller hosting-vlan-interface} no use [aaa-policy|dns-whitelist no webpage external [agreement|fail|login|welcome] no webpage internal [org-name|org-signature] no webpage internal [agreement|fail|login|welcome] [description|footer|header| main-logo|small-logo|title] Parameters no [access-time|access-type|connection-mode|inactivity-timeout| simultaneous-users|terms-agreement|webpage-location] no access-time Resets client access time no access-type Resets the client access type no connection-mode Resets the connection mode to HTTP no inactivity-timeout Resets the inactivity timeout interval
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 207 no accounting [radius|syslog] no custom-auth info no server host no server mode {centralized-controller hosting-vlan-interface} no use [aaa-policy|dns-whitelist no webpage external [agreement|fail|login|welcome] no webpage internal [org-name|org-signature] no simultaneous-users Resets the number of MAC addresses that can use a single user name, to its default of 1 no terms-agreement Resets the terms agreement requirement for logging in. The user no longer has to agree to terms & conditions before connecting to a captive portal. no webpage-location Resets the use of custom Web pages for login, welcome, terms, and failure page. The default of automatically created Web pages is used. no accounting Disables accounting configurations radius Disables support for sending RADIUS accounting messages syslog Disables support for sending syslog messages to remote syslog servers no custom-auth Resets custom authentication information info Resets the configuration of custom user information sent to the RADIUS server (for custom-auth-radius access type) no server host Clears captive portal server address no server mode Configures the captive portal server mode centralized-controller hosting-vlan-interface Optional. Resets the hosting VLAN interface for centralized captive portal server to its default value of zero (0) no use Resets profiles used with a captive portal policy aaa-policy Removes the AAA policy used with a captive portal policy dns-whitelist Removes the DNS whitelist used with a captive portal policy no webpage external Resets the configuration of external Web pages displayed when a user interacts with the captive portal agreement Resets the agreement page fail Resets the fail page login Resets the login page welcome Resets the welcome page no webpage external Resets the configuration of internal Web pages displayed when a user interacts with the captive portal org-name Resets the organization name that is included at the top of Web pages
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 208 no webpage internal [agreement|fail|login|welcome] [description|footer|header|main-logo|small-logo|title] Example wm3700-37FABE(config-captive-portal-testportal)#no webpage internal login header wm3700-37FABE(config-captive-portal-testportal)#no use aaa-policy wm3700-37FABE(config-captive-portal-testportal)#no custom-auth info wm3700-37FABE(config-captive-portal-testportal)#no accounting radius org-signature Resets the organization signature (email, addresses, phone numbers) included at the bottom of Web pages no webpage external Resets the configuration of internal Web pages displayed when a user interacts with the captive portal agreement Resets the agreement page fail Resets the fail page login Resets the login page welcome Resets the welcome page description Resets the description part of each Web page. This is the area where information about the captive portal and user state is displayed to the user. footer Resets the footer portion of each Web page. A footer can contain the organization signature header Resets the header portion of each Web page main-logo Resets the main logo of each Web page small-logo Resets the small logo of each Web page title Resets the title of each Web page
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 209 Related Commands server captive-portal-mode commands Configures captive portal server parameters, such as the hostname, IP, and mode of operation Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax server [host <WORD|mode] server host <IP/HOSTNAME> server mode [centralized|centralized-controller|self] access-time Configures the allowed access time for each captive portal client access-type Configures a captive portal authentication and logging information accounting Configures a captive portal accounting information connection-mode Configures how clients connect to a captive portal inactivity-timeout Configures the captive portal parameters required for client access inactivity-timeout Configures the client inactivity timeout interval server Configures the captive portal server parameters simultaneous-users Configures the maximum number of clients that can use a single captive portal user name terms-agreement Configures if a client has to accept terms and conditions before logging to the captive portal use Configures a AAA policy and DNS whitelist with this captive portal policy webpage-location Configures the location of Web pages displayed when the user interacts with the captive portal webpage Configures Web pages used by the captive portal to interact with users aaa-policy Configures a AAA policy dns-whitelist Configures a DNS whitelist
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 210 Parameters server host <IP/HOSTNAME> server mode [centralized|centralized-controller|self] Example wm3700-37FABE(config-captive-portal-test)#server mode self wm3700-37FABE(config-captive-portal-test)# wm3700-37FABE(config-captive-portal-test)#server host 172.16.10.9 wm3700-37FABE(config-captive-portal-test)# Related Commands simultaneous-users captive-portal-mode commands Specifies the number of MAC addresses that can simultaneously use a particular username Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax simultaneous-users <1-8192> host <IP/HOSTNAME> Configures the captive portal authentication server <IP/HOSTNAME> Specify the IP address or hostname of the captive portal server. mode Configures the captive portal server mode centralized Considers the configured server hostname or IP address as the centralized captive portal server centralized-controller Uses the configured hostname as the virtual captive portal server name across the wireless controller self Selects the captive portal server as the same device supporting the WLAN no Resets or disables captive portal commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 211 Parameters simultaneous-users <1-8192> Example wm3700-37FABE(config-captive-portal-test)#simultaneous-users 5 wm3700-37FABE(config-captive-portal-test)# Related Commands terms-agreement captive-portal-mode commands Enforces the user to agree to terms and conditions (included in the login page) for captive portal guest access Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax terms-agreement Parameters None Example wm3700-37FABE(config-captive-portal-test)#terms-agreement wm3700-37FABE(config-captive-portal-test)# <1-8192> Specifies the number of MAC addresses that can simultaneously use a particular username. Select a number from 1 - 8192. no Resets or disables captive portal commands
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 212 Related Commands use captive-portal-mode commands Configures a AAA policy and DNS whitelist with this captive portal policy. AAA policies are used to configure servers for this captive portal. DNS whitelists provide a method to restrict users to a set of configurable domains on the internet accessed through the captive portal. For more information on AAA policy, see Chapter 9, AAA Policy. For more information on DNS whitelists, see Chapter 5, Global Configuration Commands. Defines captive portal configuration settings Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [aaa-policy <AAA-POLICY>|dns-whitelist <DNS-WHITELIST>] Parameters use [aaa-policy <AAA-POLICY>|dns-whitelist <DNS-WHITELIST>] Example wm3700-37FABE(config-captive-portal-test)#use aaa-policy test wm3700-37FABE(config-captive-portal-test)#use dns-whitelist Captive_Portal_Allowed_URL_list no Resets or disables captive portal commands aaa-policy <AAA-POLICY> Configures a AAA policy with this captive portal policy. AAA policies configure servers for the captive portal. <AAA-POLICY> Specify the AAA policy name. dns-whitelist <DNS- WHITELIST> Configures a DNS whitelist to use with this captive portal policy. DNS whitelists restrict access of URLs from a captive portal. <DNS-WHITELIST> Specify the DNS whitelist name.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 213 Related Commands webpage-location captive-portal-mode commands Specifies the location of the Web pages used for authentication. These pages can either be hosted on the system or on an external Web server. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax webpage-location [advanced|external|internal] Parameters webpage-location [advanced|external|internal] Example wm3700-37FABE(config-captive-portal-test)#webpage-location internal wm3700-37FABE(config-captive-portal-test)# wm3700-37FABE(config-captive-portal-test)#webpage internal agreement title test123 wm3700-37FABE(config-captive-portal-test)# no Resets or disables captive portal commands dns-whitelist Configures a DNS whitelist aaa-policy Configures a AAA policy advanced Uses Web pages for login, welcome, failure, and terms created and stored on the wireless controller external Uses Web pages for login, welcome, failure, and terms located on an external server. Provide the URL for each of these pages internal Uses Web pages for login, welcome, and failure that are automatically generated
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 214 Related Commands webpage captive-portal-mode commands Configures Web pages displayed when interacting with a captive portal. There are four (4) different pages. agreement This page displays Terms and Conditions that a user needs to accept before allowed access to the captive portal. fail This page is displayed when the user is not authenticated to use the captive portal. login This page is displayed when the user connects to the captive portal. Use this page to fetch login credentials from the user. welcome This page is displayed to welcome an authenticated user to the captive portal. The Web pages for interacting with the users of a captive portal can be located either on the wireless controller or an external location. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax webpage [external|internal] webpage external [agreement|fail|login|welcome] <URL> webpage internal [agreement|fail|login|org-name|org-signature|welcome] webpage internal [agreement|fail|login|welcome] [description|footer| header|title] <CONTENT> webpage internal [agreement|fail|login|welcome] [main-logo|small-logo] <URL> no Resets or disables captive portal commands webpage Configures Web pages displayed for the login, welcome, fail, and terms pages for a captive portal
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 215 Parameters webpage external [agreement|fail|login|welcome] <URL> webpage internal [agreement|fail|login|welcome] description|footer|header|title] <CONTENT> webpage internal [agreement|fail|login|welcome] [main-logo|small-logo] <URL> external Indicates the Web pages being served are external to the captive portal agreement Indicates the page is displayed for Terms & Conditions fail Indicates the page is displayed for login failure login Indicates the page is displayed for getting user credentials for log in to the captive portal welcome Indicates the page is displayed after a user has successfully logged in to the captive portal <URL> Indicates the URL to the Web page displayed internal Indicates the Web pages being served are internal agreement Indicates the page is displayed for Terms & Conditions fail Indicates the page is displayed for login failure login Indicates the page is displayed for getting user credentials for log in to the captive portal welcome Indicates the page is displayed after a user has successfully logged in to the captive portal description Indicates the content is the description portion of each internal, agreement, fail, and welcome page footer Indicates the content is the footer portion of each internal, agreement, fail, and welcome page. The footer portion contains the signature of the organization that hosts the captive portal. header Indicates the content is the header portion of each internal, agreement, fail, and welcome page. The header portion contains the heading information for each of these pages. title Indicates the content is the title of each internal, agreement, fail, and welcome page. The title for each of these pages is configured here. <CONTENT> Specify the content displayed for each of the different components of the Web page. You can enter 900 characters for the description and 256 characters each for header, footer, and title. internal Indicates the Web pages being served are internal agreement Indicates the page is displayed for Terms & Conditions fail Indicates the page is displayed for login failure login Indicates the page is displayed for getting user credentials for log in to the captive portal welcome Indicates the page is displayed after a user has successfully logged in to the captive portal main-logo Indicates the main logo displayed in the header portion of each Web page small-logo Indicates the logo image displayed in the footer portion of each Web page, and constitutes the organizations signature <URL> Indicates the complete URL of the main-log and small-logo files
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 216 Example wm3700-37FABE(config-captive-portal-test)#webpage external fail www.extremenetworks.com wm3700-37FABE(config-captive-portal-test)# Related Commands no Resets or disables captive portal commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 217 clear Global Configuration Commands Clears parameters, cache entries, table entries, and other similar entries. The clear command is available for specific commands only. The information cleared using this command varies depending on the mode where executed. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax clear event-history Parameters clear event-history Example wm3700-37FABE(config)#clear event-history wm3700-37FABE(config)# event-history Clears the event history file
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 218 critical-resource-policy Global Configuration Commands Creates a critical resource monitoring policy. A critical resource is a device (wireless controller, router, gateway, etc.) considered critical to the health of the wireless controller. This is a list of IP addresses pinged regularly by the wireless controller. If there is a connectivity issue with a device on the critical resource list, an event is generated stating a critical resource is unavailable. The wireless controller does not attempt to restore connection to a critical resource. All critical devices are listed in a critical resource policy. critical-resource-policy critical-resource-policy Creates or enters a Critical-resource Monitoring (CRM) policy. If the defined policy is not present, it is created. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax critical-resource-policy <CRITICAL-RESOURCE-POLICY> Parameters critical-resource-policy <CRITICAL-RESOURCE-POLICY> Example wm3700-37FABE(config)#critical-resource-policy test wm3700-37FABE(config-critical-resource-policy-test)#? wm3700-37FABE(config-critical-resource-policy-test)#? Command Description Reference critical-resource-policy Configures captive portal Web page parameters page 5-218 <CRITICAL-RESOURCE- POLICY> Specify the critical resource monitoring policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 219 commands: monitor Critical resource monitoring no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-critical-resource-policy-test)# Related Commands critical-resource-policy-mode The following table summarizes critical resource monitoring policy commands monitor critical-resource-policy-mode Monitors critical resources. Use this command to configure a critical policy and set the interval the availability of the critical resource is checked. no Disables a critical resource policy Command Description Reference monitor Performs critical resource monitoring page 5-219 no Cancels the monitoring of a critical resource page 5-221 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from the EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 220 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax monitor [<IP>|ping-interval monitor [ping-interval <5-86400>] monitor <IP> ping-mode [arp-icmp|arp-only vlan <1-4094>] Parameters monitor ping-interval <5-86400> monitor <IP> ping-mode [arp-icmp|arp-only vlan <1-4094>] Example wm3700-37FABE(config-critical-resource-policy-test)#monitor ping-interval 10 wm3700-37FABE(config-critical-resource-policy-test)# wm3700-37FABE(config-critical-resource-policy-test)#monitor 172.16.10.2 ping-mode arp-only vlan 1 ping-interval <5-86400> Configures the ping interval. This is the duration between two successive pings to a critical resource. <5-86400> Specify the ping interval from 5 - 86400 seconds. <IP> Specify the IP address of the critical resource. ping-mode Configures the type of ping packets to use. For pinging critical resources that do not have an IP address, use the arp-only mode. arp-icmp Use Address Resolution Protocol (ARP) requests or Internet Control Message Protocol (ICMP) echo requests to monitor a critical resource. To use this ping mode, an IP address must be configured for each device in the critical resource list. arp-only vlan <1-4094> Uses ARP requests to monitor a critical resource. This mode can be used for devices that do not have a configured IP address. vlan Configures the VLAN to ping for the critical resource <1-4094> Specify a VLAN ID from 1 - 4094
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 221 wm3700-37FABE(config-critical-resource-policy-test)# Related Commands no critical-resource-policy-mode Removes a device from the critical resource list. This command also resets the ping interval to its default. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no monitor [<IP>|ping-interval] Parameters no monitor [<IP>|ping-interval] Example wm3700-37FABE(config-critical-resource-policy-test)#no monitor 172.16.10.2 wm3700-37FABE(config-critical-resource-policy-test)# Related Commands no Resets or disables critical resource policy commands monitor Configures critical resource monitoring parameters <IP> Removes a specified device from the list of monitored devices ping-interval Resets the ping interval for pinging critical resources monitor Adds a device to the critical resource policy list
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 222 customize Global Configuration Commands Customizes the output of the summary CLI commands. Use this command to define the data displayed as a result of various show commands. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax customize [hostname-column-width|show-wireless-client|show-wireless-client- stats| show-wireless-client-stats-rf|show-wireless-radio|show-wireless- radio-stats| show-wireless-radio-stats-rf] customize hostname-column-width <1-64> customize show-wireless-client (ap-name <1-64>,auth,bss,enc,hostname <1- 64>,ip, last-active,location <1-64>,mac,radio-alias <3-67>,radio-id,radio- type,state, username <1-64>,vendor,vlan,wlan) customize show-wireless-client-stats (hostname <1-64>,mac,rx-bytes,rx- errors, rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-packets,tx- throughput) customize show-wireless-client-stats-rf (average-retry-number,error-rate, hostname <1-64>,mac,noise,q-index,rx-rate,signal,snr,t-index,tx- rate) customize show-wireless-radio (adopt-to,ap-name <1-64>,channel,location <1- 64>, num-clients,power,radio-alias <3-67>,radio-id,radio-mac,rf- mode,state) customize show-wireless-radio-stats (radio-alias <3-67>,radio-id,radio-mac, rx-bytes,rx-errors,rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 223 packets, tx-throughput) customize show-wireless-radio-stats-rf (average-retry-number,error- rate,noise, q-index,radio-alias <3-67>,radio-id,radio-mac,rx-rate,signal,snr,t- index, tx-rate) Parameters customize hostname-column-width <1-64> customize show-wireless-client (ap-name <1-64>,auth,bss,enc,hostname <1- 64>,ip, last-active,location <1-64>,mac,radio-alias <3-67>,radio-id,radio- type,state, username <1-64>,vendor,vlan,wlan) hostname-column-width <1-64> Configures the default width of the hostname column in all show commands <1-64> Specify the hostname column width from 1 - 64 characters. show-wireless-client Customizes the columns displayed for the show wireless client command ap-name <1-64> Includes the ap-name column in the show wireless client command. <1-64> Specify the ap-name column width from 1 - 64 characters. auth Includes the auth column in the show wireless client command. The auth column displays the authorization protocol used by the wireless client. bss Includes the BSS column in the show wireless client command. The BSS column displays the BSSID the wireless client is associated with. enc Includes the enc column in the show wireless client command. The enc column displays the encryption suite used by the wireless client. hostname <1-64> Includes the hostname column in the show wireless client command. The hostname column displays the hostname of the wireless client. <1-64> Specify the hostname column width from 1 - 64 characters. ip Includes the IP column in the show wireless client command. The IP column displays the current IP address of the wireless client. last-active Includes the last-active column in the show wireless client command. The last- active column displays the time of the last activity seen from the wireless client. location <1-64> Includes the location column in the show wireless client command. The location column displays the location of the AP the wireless client is associated with. <1-64> Specify the location column width from 1 - 64 characters. mac Includes the MAC column in the show wireless client command. The MAC column displays the MAC address of the wireless client. radio-alias <3-67> Includes the radio-alias column in the show wireless client command. The radio- alias column displays the radio alias with the AP's hostname and the radio interface number in the HOSTNAME:RX format. <1-64> Specify the radio-alias column width from 3 - 67 characters. radio-id Includes the radio-id column in the show wireless client command. The radio-id column displays the radio ID with the APs MAC address and the radio interface number in the AA-BB-CC-DD-EE-FF:RX format.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 224 customize show-wireless-client-stats (hostname <1-64>,mac,rx-bytes,rx- errors, rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-packets,tx-throughput) radio-type Includes the radio-type column in the show wireless client command. The radio- type column displays the radio type of the wireless client. state Includes the state column in the show wireless client command. The state column displays the current availability state of the wireless client. username <1-64> Includes the username column in the show wireless client command. The username column displays the username used to logon by the wireless client. <1-64> Specify the username column width from 1 - 64 characters. vendor Includes the vendor column in the show wireless client command. The vendor column displays the vendor ID of the wireless client. vlan Includes the VLAN column in the show wireless client command. The VLAN column displays the VLAN assigned to the wireless client. wlan Includes the WLAN column in the show wireless client command. The WLAN column displays the WLAN assigned to the wireless client. show-wireless-client-stats Customizes the columns displayed for the show wireless client statistics command hostname <1-64> Includes the hostname column in the show wireless client statistics command. The hostname column displays the hostname of the wireless client. <1-64> Sets the hostname column width from 1 - 64 characters mac Includes the MAC column in the show wireless client statistics command. The MAC column displays the MAC address of the wireless client. rx-bytes Includes the rx-bytes column in the show wireless client statistics command. The rx-bytes column displays the total number of bytes received by the wireless client. rx-errors Includes the rx-error column in the show wireless client statistics command. The rx-error column displays the total number of receive errors received by the wireless client. rx-packets Includes the rx-packets column in the show wireless client statistics command. The rx-packets column displays the total number of packets received by the wireless client. rx-throughput Includes the rx-throughput column in the show wireless client statistics command. The rx-throughput column displays the receive throughput at the wireless client. tx-bytes Includes the tx-bytes column in the show wireless client statistics command. The tx-bytes column displays the total number of bytes transmitted by the wireless client. tx-dropped Includes the tx-dropped column in the show wireless client statistics command. The tx-dropped column displays the total number of dropped packets by the wireless client. tx-packets Includes the tx-packets column in the show wireless client statistics command. The tx-packets column displays the total number of packets transmitted by the wireless client. tx-throughput Includes the tx-throughput column in the show wireless client statistics command. The tx-throughput column displays the transmission throughput at the wireless client.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 225 customize show-wireless-client-stats-rf (average-retry-number,error-rate, hostname <1-64>,mac,noise,q-index,rx-rate,signal,snr,t-index,tx-rate) customize show-wireless-radio (adopt-to,ap-name <1-64>,channel,location <1- 64>, num-clients,power,radio-alias <3-67>,radio-id,radio-mac,rf-mode,state) show-wireless-client-stats- rf Customizes the columns displayed for the show wireless client stats rf command average-retry-number Includes the average-retry-number column in the show wireless client statistics RF command. The average-retry-number column displays the average number of retransmissions per packet. error-rate Includes the error-rate column in the show wireless client statistics rf command. The error-rate column displays the error rate information for the wireless client. hostname <1-64> Includes the hostname column in the show wireless client statistics RF command. The hostname column displays the hostname of the wireless client. <1-64> Specify the hostname column width from 1 - 64 characters. mac Includes the MAC column in the show wireless client statistics RF command. The MAC column displays the MAC address of the wireless client. noise Includes the noise column in the show wireless client statistics RF command. The MAC column displays the noise as detected by the wireless client. q-index Includes the q-index column in the show wireless client statistics RF command. The q-index column displays the RF quality index where a higher value indicates better RF quality. rx-rate Includes the rx-rate column in the show wireless client statistics RF command. The rx-rate column displays the receive rate at the particular wireless client. signal Includes the signal column in the show wireless client statistics RF command. The signal column displays the signal strength at the particular wireless client. snr Includes the snr column in the show wireless client statistics RF command. The snr column displays the signal to noise ratio at the particular wireless client. t-index Includes the t-index column in the show wireless client statistics RF command. The t-index column displays the traffic utilization index at the wireless controller. tx-rate Includes the tx-rate column in the show wireless client statistics RF command. The tx-rate column displays the packet transmission rate at the particular wireless client. show-wireless-radio Customizes the columns displayed for the show wireless radio command. adopt-to Includes the adopt-to column in the show wireless radio command. The adopt-to column displays information about the wireless controller adopting this AP. ap-name <1-64> Includes the ap-name column in the show wireless radio command. The adopt-to column displays information about the AP this radio belongs. <1-64> Specify the ap-name column width from 1 - 64 characters. channel Includes the channel column in the show wireless radio command. The channel column displays information about the configured and current channel of operation for this radio. location <1-64> Includes the location column in the show wireless radio command. The location column displays the location of the AP this radio belongs. <1-64> Specify the location column width from 1 - 64 characters. num-clients Includes the num-clients column in the show wireless radio command. The num- clients column displays the number of clients associated with this radio. power Includes the power column in the show wireless radio command. The power column displays the configured and current transmit power of the radio.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 226 customize show-wireless-radio-stats (radio-alias <3-67>,radio-id,radio-mac, rx-bytes,rx-errors,rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-packets, tx-throughput) radio-alias <3-67> Includes the radio-alias column in the show wireless radio command. The radio- alias column displays the radio alias along with the AP's hostname and the radio interface number in the HOSTNAME:RX formate. <3-67> Specify the radio-alias column width from 3 - 67 characters. radio-id Includes the radio-id column in the show wireless radio command. The radio-id column displays the Radio ID along with the APs MAC address and the radio interface number in the AA-BB-CC-DD-EE-FF:RX format. radio-mac Includes the radio-mac column in the show wireless radio command. The radio- mac column displays the base MAC address of the radio. rf-mode Includes the rf-mode column in the show wireless radio command. The rf-mode column displays the mode in which the radio operates. The radio mode can be 2.4GHz, 5GHz, or sensor. state Includes the state column in the show wireless radio command. The state column displays the current operational state of the radio. show-wireless-radio-stats Customizes the columns displayed for the show wireless radio statistics command. radio-alias <3-67> Includes the radio-alias column in the show wireless radio statistics command. The radio-alias column displays the radio alias along with the AP's hostname and the radio interface number in the HOSTNAME:RX format. <3-67> Specify the radio-alias column width from 3 - 67 characters. radio-id Includes the radio-id column in the show wireless radio statistics command. The radio-id column displays the Radio ID along with the APs MAC address and the radio interface number in the AA-BB-CC-DD-EE-FF:RX format. radio-mac Includes the radio-mac column in the show wireless radio statistics command. The radio-mac column displays the base MAC address of the radio. rx-bytes Includes the rx-bytes column in the show wireless radio statistics command. The rx-bytes column displays the total number of bytes received by the wireless radio. rx-errors Includes the rx-error column in the show wireless radio statistics command. The rx-error column displays the total number of receive errors received by the wireless radio. rx-packets Includes the rx-packets column in the show wireless radio statistics command. The rx-packets column displays the total number of packets received by the wireless radio. rx-throughput Includes the rx-throughput column in the show wireless radio statistics command. The rx-throughput column displays the receive throughput at the wireless radio. tx-bytes Includes the tx-bytes column in the show wireless radio statistics command. The tx-bytes column displays the total number of bytes transmitted by the wireless radio. tx-dropped Includes the tx-dropped column in the show wireless radio statistics command. The tx-dropped column displays the total number of dropped packets by the wireless radio.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 227 customize show-wireless-radio-stats-rf (average-retry-number,error- rate,noise, q-index,radio-alias <3-67>,radio-id,radio-mac,rx-rate,signal,snr,t-index, tx-rate) Example wm3700-37FABE(config)*#customize show-wireless-client ap-name auth wm3700-37FABE(config)*#commit wm3700-37FABE(config)*#show wireless client ----------------------- tx-packets Includes the tx-packets column in the show wireless radio statistics command. The tx-packets column displays the total number of packets transmitted by the wireless radio. tx-throughput Includes the tx-throughput column in the show wireless radio statistics command. The tx-throughput column displays the transmission throughput at the wireless radio. show-wireless-radio-stats-rf Customizes the columns displayed for the show wireless radio stats RF command average-retry-number Includes the average-retry-number column in the show wireless radio statistics RF command. The average-retry-number column displays the average number of retransmissions per packet. error-rate Includes the error-rate column in the show wireless radio statistics RF command. The error-rate column displays the error rate information for the wireless radio. noise Includes the noise column in the show wireless radio statistics RF command. The mac column displays the noise as detected by the wireless radio. q-index Includes the q-index column in the show wireless client statistics RF command. The q-index column displays the RF quality index where a higher value indicates better RF quality. radio-alias <3-67> Includes the radio-alias column in the show wireless radio statistics RF command. The radio-alias column displays the radio alias along with AP's hostname and the radio interface number in the HOSTNAME:RX format. <3-67> Specify the radio-alias width column from 3 - 67 characters. radio-id Includes the radio-id column in the show wireless radio statistics rf command. The radio-id column displays the Radio ID along with the APs MAC address and the radio interface number in the AA-BB-CC-DD-EE-FF:RX format. radio-mac Includes the radio-mac column in the show wireless radio statistics RF command. The radio-mac column displays the base MAC address of the radio. rx-rate Includes the rx-rate column in the show wireless radio statistics RF command. The rx-rate column displays the receive rate at the particular wireless radio. signal Includes the signal column in the show wireless radio statistics RF command. The signal column displays the signal strength at the particular wireless radio. snr Includes the snr column in the show wireless radio statistics RF command. The snr column displays the signal to noise ratio at the particular wireless radio. t-index Includes the t-index column in the show wireless radio statistics RF command. The t-index column displays the traffic utilization index at the wireless controller. tx-rate Includes the tx-rate column in the show wireless radio statistics RF command. The tx-rate column displays the packet transmission rate at the particular wireless radio.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 228 AP-NAME AUTH ----------------------- ----------------------- Total number of wireless clients displayed: 0 wm3700-37FABE(config)*# Related Commands no Resets values or disables commands wireless Displays wireless configuration and other information
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 229 device Global Configuration Commands Enables simultaneous configuration of multiple devices Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax device {containing|filter} device device containing <STRING> {filter type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700| wm3400|wm3600|wm3700]} device filter type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|wm3400|wm3600| wm3700] Parameters device device containing <STRING> {filter type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700| wm3400|wm3600|wm3700]} device Configures a basic device profile containing <STRING> Configures the search string to search for in the devices hostname. Only those devices that have the search string in their hostname can be configured. <STRING> Specify the string to search for in the hostname of the devices filter type Optional. Filters out a specific device type ap4021 Optional. Filters out all devices other than AP4021s ap4600 Optional. Filters out devices other than AP4600s ap4511 Optional. Filters out devices other than AP4511s ap4521 Optional. Filters out devices other than AP4521s
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 230 device filter type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|wm3400|wm3600| wm3700] wm3700-37FABE(config)#device containing ap filter type AP4700 % Error: Parsing cmd line (1) wm3700-37FABE(config)# wm3700-37FABE(config)#device containing ap filter type ap4600 wm3700-37FABE(config-device-{'type': 'ap4600', 'con)# Related Commands ap4532 Optional. Filters out devices other than AP4532s ap4700 Optional. Filters out devices other than AP4700s wm3400 Optional. Filters out devices other than WM3400s wm3600 Optional. Filters out devices other than WM3600s wm3700 Optional. Filters out devices other than WM3700s filter type Filters out a specific device type ap4021 Filters out all devices other than AP4021s ap4600 Filters out devices other than AP4600s ap4511 Filters out devices other than AP4511s ap4521 Filters out devices other than AP4521s ap4532 Filters out devices other than AP4532s ap4700 Filters out devices other than AP4700s wm3400 Filters out devices other than WM3400s wm3600 Filters out devices other than WM3600s wm3700 Filters out devices other than WM3700s no Resets values or disables commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 231 device-categorization Global Configuration Commands Categorizes devices as sanctioned or neighboring. Categorization of devices enables quick identification and blocking of rogue/unsanctioned devices in the wireless controller managed network. device-categorization device-categorization Configures a device categorization list. This list categorizes devices as sanctioned or neighboring. This information determines which devices are allowed access to the wireless controller managed network and which are rogue devices. If a device categorization list does not exist, it is created. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax device-categorization <DEVICE-CATEGORIZATION-LIST-NAME> Parameters device-categorization <DEVICE-CATEGORIZATION-LIST-NAME> Example wm3700-37FABE(config)#device-categorization WM3700 wm3700-37FABE(config-device-categorization-WM3700)#? Device Category Mode commands: mark-device Add a device Command Description Reference device-categorization Configures a device categorization list page 5-231 <DEVICE-CATEGORIZATION- LIST-NAME> Specify the device categorization list name. If a list with the same name does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 232 no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-device-categorization-WM3700)# Related Commands device-categorization-mode commands device-categorization The following table summarizes device categorization mode commands mark-device device-categorization-mode commands Adds a device to the device categorization list as sanctioned or neighboring. Devices are further classified as AP or client. no Resets values or disables commands Command Description Reference mark-device Adds a device to the device categorization list page 5-232 no Removes a device from the device categorization list page 5-234 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 233 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mark-device [sanctioned|neighboring] [ap|client] mark-device [sanctioned|neighboring] ap [<MAC>|any] ssid [<SSID>|any] mark-device [sanctioned|neighboring] client [<MAC>|any] Parameters mark-device [sanctioned|neighboring] ap [<MAC>|any] ssid [<SSID>|any] mark-device [sanctioned|neighboring] client [<MAC>|any] sanctioned Marks a device as sanctioned. A sanctioned device is authorized to use network resources by providing correct credentials. neighboring Marks a device as neighboring. A neighboring device is a neighbor in the same network as this device. ap [<MAC>|any] Marks all or a specified AP as sanctioned or neighboring based on their MAC addresses <MAC> Specify the MAC address of the AP. any Indicates all APs are marked ssid [<SSID>|any] Configures the SSID for the AP. Any AP with the configured SSID is automatically marked. When the any parameter is used, any AP with any SSID is automatically marked. <SSID> Specify the SSID. any Indicates any SSID to match sanctioned Marks the wireless client as sanctioned. A sanctioned device is authorized to use network resources by providing correct credentials. neighboring Marks the wireless client as neighboring. A neighboring device is a neighbor in the same network as this device. client [<MAC>|any] Marks all or a specified wireless client as sanctioned or neighboring based on the MAC address <MAC> Specify the MAC address of the wireless client. any Indicates all wireless clients are marked
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 234 Example wm3700-37FABE(config-device-categorization-WM3700)#mark-device sanctioned ap any ssid any wm3700-37FABE(config-device-categorization-WM3700)# wm3700-37FABE(config-device-categorization-WM3700)#mark-device neighboring client 11-22-33-44-55-66 wm3700-37FABE(config-device-categorization-WM3700)# Related Commands no device-categorization-mode commands Removes a device from the device categorization list Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no mark-device [neighboring|sanctioned] [ap|client] [<MAC>|any] mark-device [sanctioned|neighboring] client [<MAC>|any] mark-device [sanctioned|neighboring] ap [<MAC>|any] ssid [<SSID>|any] Parameters no mark-device [sanctioned|neighboring] ap [<MAC>|any] ssid [<SSID>|any] no Resets or disables mark device commands no mark-device Removes a device from the marked device list sanctioned Removes a device marked as sanctioned. A sanctioned device is authorized to use network resources by providing correct credentials. neighboring Removes a device marked as neighboring. A neighboring device is a neighbor in the same network as this device.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 235 no mark-device [sanctioned|neighboring] client [<MAC>|any] Example wm3700-37FABE(config-device-categorization-WM3700)#no mark-device authorized ap any ssid 1 %% Error: Parsing cmd line wm3700-37FABE(config-device-categorization-WM3700)# Related Commands ap [<MAC>|any] Removes all or a specified AP as sanctioned or neighboring <MAC> Specify the MAC address of the AP. any Indicates all APs are marked ssid [<SSID>|any] Configures the APs SSID. Any AP with the configured SSID is removed from the marked list. When the any parameter is used, any AP with any SSID is removed from the marked list. <SSID> Specify the SSID. any Indicates any SSID to match no mark-device Removes a device from the marked device list sanctioned Marks the wireless client as sanctioned. A sanctioned device is authorized to use network resources by providing correct credentials. neighboring Removes a wireless client marked as neighboring. A neighboring device is a neighbor in the same network as this device. client [<MAC>|any] Removes all or a specified wireless client marked as sanctioned or neighboring <MAC> Specify the MAC address of the wireless client. any Indicates all wireless clients are removed from the marked list mark-device Adds a device to a list of sanctioned or neighboring devices
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 236 dhcp-server-policy Global Configuration Commands Configures DHCP server policy parameters, such as class, address range, and options. A new policy is created if it does not exist. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-server-policy <DHCP-POLICY-NAME> Parameters dhcp-server-policy <DHCP-POLICY-NAME> Example wm3700-37FABE(config)#dhcp-policy test wm3700-37FABE(config)#? Related Commands NOTE For more information on DHCP policy, see Chapter 14, DHCP Server Policy. <DHCP-POLICY-NAME> Specify the DHCP policy name. If the policy does not exist, it is created. no Resets values or disables commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 237 dns-whitelist Global Configuration Commands Configures a whitelist of devices permitted to access the wireless controller managed network or a hotspot dns-whitelist dns-whitelist Configures a DNS whitelist. A DNS whitelist is a list of domains allowed access to the wireless controller managed network. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dns-whitelist <DNS-WHITELIST> Parameters dns-whitelist <DNS-WHITELIST> Example wm3700-37FABE(config-dns-whitelist-test)#? DNS Whitelist Mode commands: no Negate a command or set its defaults permit Match a host clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode Command Description Reference dns-whitelist Configures the DNS whitelist page 5-237 <DNS-WHITELIST> Specify the DNS whitelist name. If the whitelist does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 238 exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-dns-whitelist-test)# Related Commands dns-whitelist mode commands dns-whitelist The following table summarizes DNS white list mode commands permit dns-whitelist mode commands A whitelist is a list of host names and IP addresses permitted access to the wireless controller managed network or captive portal. This command adds a device by its hostname or IP address to the DNS whitelist. no Resets values or disables commands Command Description Reference permit Matches a host page 5-238 no Negates a command or sets its default values page 5-239 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 239 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax permit <IP/HOSTNAME> {suffix} Parameters permit <IP/HOSTNAME> {suffix} Example wm3700-37FABE(config-dns-whitelist-test)#permit extremenetworks.com suffix wm3700-37FABE(config-dns-whitelist-test)#show context dns-whitelist test permit extremenetworks.com suffix wm3700-37FABE(config-dns-whitelist-test)# Related Commands no dns-whitelist mode commands Removes a specified host or IP address from the DNS whitelist, and prevents it from accessing network resources <IP/HOSTNAME> Specify the IP address or hostname of the device, to add to the DNS whitelist. suffix Optional. Matches any hostname including the specified name as suffix no Resets or disables DNS whitelist commands
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 240 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no permit <IP/HOSTNAME> Parameters no permit <IP/HOSTNAME> Example wm3700-37FABE(config-dns-whitelist-test)#no permit joysportsview.com wm3700-37FABE(config-dns-whitelist-test)# Related Commands <IP/HOSTNAME> Specify the devices IP address or hostname to remove from the DNS whitelist. permit Adds a device to the DNS whitelist
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 241 do Global Configuration Commands Use the do command to run commands from the EXEC mode. These commands perform tasks, such as clearing caches, setting device clock, upgrades etc. Generally use the do command to execute commands from the Privilege Executable or User Executable modes. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax do [ap-upgrade|archive|boot|cd|change- passwd|clear|clock|clrscr|cluster|commit| configure|connect|copy|crypto|debug|delete|diff|dir|disable|edit|enable| erase|exit|format|halt|help|logging|mint|mkdir|more|no|page|ping|pwd|reload | remote- debug|rename|revert|rmdir|self|service|show|telnet|terminal|time-it| traceroute|upgrade|upgrade-abort|watch|write|ssh do ap-upgrade [<DEVICE- NAME>|all|all|ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|load-image|rf- domain|cancel-upgrade] do archive tar [/create|/table|/xtract] [<FILE>|<URL>] do boot system [primary|secondary] {on <DEVICE-NAME>} do cd {<DIR>} do change-passwd {<OLD-PASSWORD>} {<NEW-PASSWORD>} do clear [arp-cache|cdp|counters|event-history|firewall|ip|lldp|spanning- tree| crypto] do clock set <TIME> <DAY> <MONTH> <YEAR>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 242 do clrscr do cluster start-election do commit write memory do configure [terminal|self] do connect [<REMOTE-DEVICE>|mint-id <DEVICE-MINT-ID>] do copy [<SOURCE-FILE>|<SOURCE-URL>] [<DESTINATION-FILE>|<DESTINATION-URL>] do crypto [key|pki] do delete /force /recursive <FILE> do diff [<FILE1>|<URL1>] [<FILE2>|<URL2>] do dir {/all} {/recursive} {<DIR>} {all-filesystems} do disable do edit <FILE> do enable do erase [cf:|flash:|nvram:|startup-config|usb1] do exit do format cf: do halt {on <DEVICE>} do help {[search|show]} do logging monitor {[<0-7>|alerts|critical|debugging|emergencies|errors| informational|notification|warnings]} do mint [ping|traceroute] <MINT-DEVICE-ID> do mkdir <DIR> do more <FILE> do no [adoption|captive-portal|crypto|debug|page|service|terminal|upgrade| wireless|logging] do page do ping <IP> do pwd
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 243 do reload {[cancel|force|in|on]} do rename <FILE> do revert do rmdir <DIR> do self do service [advanced-wips|clear|cli-tables-expand|cli-tables-skin|cluster| copy|force-send- config|locator|mint|noc|pktcap|pm|radio|radius|set|show| smart-rf|start-shell|wireless|signal do show [adoption|advanced-wips|ap-upgrade|boot|captive- portal|cdp|clock|cluster| commands|critical-resources|crypto|debug|debugging|device- categorization| event-history|event-system-policy|file|firewall|interface|ip| ip-access-list-stats|licenses|lldp|logging|mac-access-list-stats| mac-address-table|mint|noc|ntp|password- encryption|power|reload|remote-debug| rf-domain-manager|role|running-config session-changes|session- config| sessions smart-rf|spanning-tree|startup- config|terminal|timezone|upgrade-status| version|wireless|wwan|context] do ssh <IP> do telnet <IP/HOSTNAME> do terminal [length <LINES>|width <CHARACTERS>] do time-it <CLI-COMMAND> do traceroute <ARGS> do upgrade [<FILE>|<URL> do upgrade-abort {on <DEVICE>} do watch <TIME> <CLI-COMMAND> do write [memory|terminal]
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 244 Parameters do ap-upgrade [<DEVICE- NAME>|all|all|ap4021|ap4600|ap4511|ap4521|ap4532|ap4700| load-image|rf-domain|cancel-upgrade] do archive tar [/create|/table|/xtract] [<FILE>|<URL>] do boot system [primary|secondary] {on <DEVICE-NAME>} do cd {<DIR>} do change-passwd {<OLD-PASSWORD>} {<NEW-PASSWORD>} do clear [arp-cache|cdp|counters|event-history|firewall|ip|lldp|spanning- tree| crypto] do clock set <TIME> <DAY> <MONTH> <YEAR> do clrscr do cluster start-election ap-upgrade Runs the ap-upgrade command For more information on the AP upgrade command, see ap-upgrade. archive Runs the archive command For more information on the archive command, see archive. boot Configures the image used for the next boot For more information on the boot command, see boot. cd <DIR> Runs the command to change the present working directory For more information on the cd command see dir. change-passwd {<OLD-PASSWORD>} {<NEW-PASSWORD>} Changes password of the logged user For more information on the clear command, see change-passwd. clear Clears some configurations For more information on the clear command, see clear. clock set <TIME> <DAY> <MONTH> <YEAR> Sets the devices time and date For more information on the clock command, see clock. clrscr Clears the current screen For more information on the clrscr command, see clrscr. cluster start-election Starts the configuration for creating a cluster of servers For more information on the cluster command, see cluster.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 245 do commit writer memory do configure [terminal|self] do connect [<REMOTE-DEVICE>|mint-id <DEVICE-MINT-ID>] do copy [<SOURCE-FILE>|<SOURCE-URL>] [<DESTINATION-FILE>|<DESTINATION-URL>] do crypto [key|pki] do delete /force /recursive <FILE> do diff [<FILE1>|<URL1>] [<FILE2>|<URL2>] do dir {/all} {/recursive} {<DIR>} {all-filesystems} do disable commit write memory Commits the changes made in the current CLI session For more information on the commit command, see commit. configure [terminal|self] Changes the configuration mode For more information on the configure command, see configure. connect [<REMOTE- DEVICE>| mint-id <DEVICE-MINT-ID>] Connects to a remote device to configure it. This command uses a devices hostname or its MiNT ID to connect. For more information on the connect command, see connect. copy [<SOURCE-FILE>| <SOURCE-URL>] [<DESTINATION-FILE>| <DESTINATION-URL>] Copies a file from one location to another For more information on the copy command, see copy. crypto [key|pki] Configures the crypto command For more information on the crypto command, see crypto. delete /force /recursive <FILE> Deletes a file from the devices file system For more information on the delete command, see disable. diff [<FILE1>|<URL1>] [<FILE2>|<URL2>] Compares two files and displays the difference between them For more information on the diff command, see diff. dir {/all} {/recursive} {<DIR>} {all-filesystems} Displays the content of a directory in the devices file system For more information on the dir command, see dir. disable Moves the control to the User Exec mode For more information on the disable command, see disable.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 246 do edit <FILE> do enable do erase [cf:|flash:|nvram:|startup-config|usb1] do exit do format cf: do halt {on <DEVICE-NAME>} do help {[search|show]} do logging monitor {[<0-7>|alerts|critical|debugging|emergencies|errors| informational|notification|warnings]} do mint [ping|traceroute] <MINT-DEVICE-ID> edit <FILE> Edits a file For more information on the edit command, see edit. enable Moves the mode to Privilege Exec mode For more information on the enable command, see enable. do erase [cf:|flash:|nvram:| startup-config|usb1] Erases the content of the specified storage device. Also erases the startup configuration to restore the device to its default. For more information on the erase command, see erase. exit Exits the CLI For more information on the exit command, see exit. format cf: Formats the CF card installed on the device For more information on the format command, see format. halt {on <DEVICE-NAME>} Stops the device For more information on the halt command, see halt. help {[search|show]} Displays the command line interface help For more information on the help command, see help. logging monitor {<0-7>|alerts|critical| debugging|emergencies| errors|informational| notification|warnings} Configures the logging level for the device For more information on the logging command, see logging. mint [ping|traceroute] <MINT-DEVICE-ID> Performs MiNT operations such as ping and traceroute For more information on the mint command, see mint.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 247 do mkdir <DIR> do more <FILE> do no [adoption|captive-portal|crypto|debug|page|service|terminal| upgrade|wireless|logging] do page do ping <IP> do pwd do reload {[cancel|force|in|on]} do rename <FILE> do revert mkdir <DIR> Creates a directory in the devices file structure For more information on the dir command, see mkdir. more <FILE> Displays a file in the console window For more information on the more command, see more. no [adoption| captive-portal| crypto|debug|page| service| terminal|upgrade| wireless|logging] Reverts or negates a command For more information on the no command, see the respective profiles and modes. page Toggles paging of the command line interface For more information on the page command, see page. ping <IP> Pings a device to check its availability For more information on the ping command, see ping. pwd Displays the current working directory For more information on the pwd command, see pwd. reload {[cancel|force|in|on]} Halts the device and performs a warm reboot For more information on the reload command, see reload. rename <FILE> Renames a file on the devices file system For more information on the rename command, see rename. revert Reverts the changes made to the system during the current CLI session For more information on the revert command, see revert.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 248 do rmdir <DIR> do self do service [advanced-wips|clear|cli-tables-expand|cli-tables-skin|cluster| copy|force-send-config|locator|mint|noc|pktcap|pm|radio|radius|set|show| smart-rf|start-shell|wireless|signal do show [adoption|advanced-wips|ap-upgrade|boot|captive-portal|cdp|clock| cluster|commands|critical-resources|crypto|debug|debugging|device- categorization| event-history|event-system-policy|file|firewall|interface|ip| ip-access-list-stats|licenses|lldp|logging|mac-access-list-stats| mac-address-table|mint|noc|ntp|password-encryption|power|reload|remote- debug| rf-domain-manager|role|running-config session-changes|session-config| sessions-smart-rf|spanning-tree|startup-config|terminal|timezone|upgrade- rmdir <DIR> Removes a directory in the devices file system For more information on the rmdir command, see rmdir. self Loads the configuration context of the device currently logged into For more information on the self command, see self. service [advanced-wips| clear|cli-tables-expand| cli-tables-skin|cluster| copy|force-send-config| locator|mint|noc|pktcap|pm| radio|radius|set|show| smart-rf|start-shell| wireless|signal Performs the different service commands For more information on the service commands, see service.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 249 status| version|wireless|wwan|context] do ssh <IP> do telnet <IP/HOSTNAME> do terminal [length <LINES>|width <CHARACTERS>] do time-it <CLI-COMMAND> do traceroute <ARGS> show [adoption| advanced-wips|ap-upgrade| boot|captive-portal| cdp|clock|cluster|commands| critical-resources| crypto|debug| debugging| device-categorization| event-history| event-system-policy| file|firewall|interface|ip| ip-access-list-stats| licenses|lldp|logging| mac-access-list-stats| mac-address-table|mint|noc| ntp|password-encryption| power|reload|remote-debug| rf-domain-manager|role| running-config| session-changes| session-config| sessions-smart-rf| spanning-tree|startup-config| terminal|timezone| upgrade-status|version| wireless|wwan|context] Displays information about the state of device, its configuration, its current status, and statistics For more information on the show command, see show. ssh <IP> Connects to a device using the SSH protocol For more information on the SSH command, see ssh. telnet <IP/HOSTNAME> Connects to a device using the Telnet protocol For more information on the Telnet command, see telnet. do terminal [length <LINES>| width <CHARACTERS>] Configures the CLI display characteristics For more information on the terminal command, see terminal. time-it <CLI-COMMAND> Captures the time required to execute a command in the CLI For more information on the time-it command, see time-it. traceroute <ARGS> Traces the path to the target devices through the network For more information on the traceroute command, see traceroute.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 250 do upgrade [<FILE>|<URL> do upgrade-abort {on <DEVICE>} do watch <TIME> <CLI-COMMAND> do write [memory|terminal] Example wm3700-37FABE(config)#do ? ap-upgrade AP firmware upgrade archive Manage archive files boot Boot commands cd Change current directory change-passwd Change password clear Clear clock Configure software system clock cluster Cluster commands commit Commit all changes made in this session configure Enter configuration mode connect Open a console connection to a remote device copy Copy from one file to another crypto Encryption related commands debug Debugging functions delete Deletes specified file from the system. diff Display differences between two files dir List files on a filesystem disable Turn off privileged mode command edit Edit a text file enable Turn on privileged mode command erase Erase a filesystem format Format file system halt Halt the system help Description of the interactive help system logging Modify message logging facilities mint MiNT protocol mkdir Create a directory more Display the contents of a file upgrade [<FILE>|<URL> Upgrades the devices firmware from a file or a location For more information on the upgrade command, see upgrade. upgrade-abort {on <DEVICE- NAME>} Aborts an upgrade in progress on the logged device or remote device For more information on the upgrade abort command, see upgrade-abort. watch <TIME> <CLI-COMMAND> Repeats a CLI command at a periodic interval For more information on the watch command, see watch. write [memory|terminal] Writes the changes made to the running configuration to the memory or to the terminal For more information on the write command, see write.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 251 no Negate a command or set its defaults page Toggle paging ping Send ICMP echo messages pwd Display current directory reload Halt and perform a warm reboot remote-debug Troubleshoot remote system(s) rename Rename a file revert Revert changes rmdir Delete a directory self Config context of the device currently logged into ssh Open an ssh connection telnet Open a telnet connection terminal Set terminal line parameters time-it Check how long a particular command took between request and completion of response traceroute Trace route to destination upgrade Upgrade software image upgrade-abort Abort an ongoing upgrade watch Repeat the specific CLI command at a periodic interval write Write running configuration to memory or terminal clrscr Clears the display screen exit Exit from the CLI service Service Commands show Show running system information wm3700-37FABE(config)# Related Commands ap-upgrade Runs the ap update command archive Runs the archive command boot Configures the image used for the next boot cd Runs the command to change the present working directory change-passwd Changes the password for the current login user clear Clears some configurations clock Configures a devices time and date clrscr Clears the current screen cluster Starts the configuration for creating a cluster of servers commit Commits changes made in the current CLI session configure Changes the configuration mode connect Configures a remote device. This command uses a devices hostname or MiNT ID to connect. copy Copies a file from one location to another crypto Configures the crypto command delete Deletes a file from a devices filesystem diff Compares two files and displays the difference dir Displays the content of a directory in the devices file system
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 252 disable Moves the control to the User Exec mode edit Edits a file enable Moves the mode to Privilege Exec mode enable Erases the content of the specified storage device. Also erases the startup configuration to restore the device to its default. exit Exits from the CLI format Formats the CF card installed on a device halt Stops a device help Displays the CLI help logging Configures a devices logging mint Performs MiNT operations such as ping and traceroute mkdir Creates a directory in the devices file structure more Displays a file in the console window no Reverts or negates a command page Toggles paging of the command line interface ping Pings a device to check its availability pwd Displays the current working directory reload Halts a device and performs a warm reboot rename Renames a file on a devices file system revert Reverts changes made to the system during the current CLI session rmdir Removes a directory in a devices file system self Loads a devices configuration context service Executes service commands ssh Connects to a device using SSH show Displays a devices state, configuration, and statistics telnet Uses Telnet to connect to a device terminal Configures the CLI display characteristics time-it Captures the time required to execute a command in the CLI traceroute Traces the path to target devices upgrade Upgrades a devices firmware from a file or a location upgrade-abort Aborts an upgrade in progress on a logged or a remote device watch Repeats a CLI command at a periodic interval write Writes the changes made in the current session to the memory
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 253 end Global Configuration Commands Ends and exits the current mode and moves to the PRIV EXEC mode The prompt changes to the PRIV EXEC mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax end Parameters None Example wm3700-37FABE(config)#end wm3700-37FABE#
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 254 event-system-policy Global Configuration Commands Configures how events are supported by the wireless controller. Each event can be configured individually to perform an action such as sending an e-mail or forwarding a notification to its parent wireless controller etc. event-system-policy event-system-policy Configures a system wide events handling policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax event-system-policy <EVENT-SYSTEM-POLICY> Parameters event-system-policy <EVENT-SYSTEM-POLICY> Example wm3700-37FABE(config)#event-system-policy event-testpolicy wm3700-37FABE(config-event-system-policy-event-testpolicy)#? wm3700-37FABE(config-event-system-policy-event-testpolicy)#? Event System Policy Mode commands: event Configure an event no Negate a command or set its defaults Command Description Reference event-system-policy Configures the event system policy page 5-254 <EVENT-SYSTEM- POLICY> Specify the event system policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 255 clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-event-system-policy-event-testpolicy)# Related Commands event-system-policy mode commands event-system-policy The following table summarizes event system policy mode commands event event-system-policy mode commands Configures an event and sets the action performed when the event happens no Removes an event system policy Command Description Reference event Configures an event page 5-255 no Negates a command or sets its default values page 5-265 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 256 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax event <EVENT-TYPE> <EVENT> (email,forward-to-switch,snmp,syslog) [default|on|off] NOTE The parameter values for <event type> and <event name> are summarized in the table under the Parameters section. Parameters event <EVENT-TYPE> <EVENT> (email,forward-to-switch,snmp,syslog) [default|on|off] <event type> <event name> aaa Configures authentication, authorization, and accounting related event messages radius-discon-msg RADIUS disconnection message radius-session-expired RADIUS session expired message radius-session-not-started RADIUS session not started message radius-vlan-update RADIUS VLAN update message
TM 4000 Series Access Point CLI Reference Guide 262 filemgmt Configures file management module related event messages http Event HTTP message httplocal Event HTTP local message https-start Event HTTPS start message https-wait Event HTTPS wait message httpstart Event HTTP start message keyadded Event key added message keydeleted Event key deleted message trustpointdeleted Event trustpoint deleted message fwu Configures firmware update related event messages fwuaborted Event fwu aborted message fwubadconfig Event fwu bad config message fwucorruptedfile Event fwu corrupted file message fwucouldntgetfile Event fwu could not get file message fwudone Event fwu done message fwufileundef Event fwu file undefined message fwunoneed Event fwu no need message fwuprodmismatch Event fwu prod mismatch message fwuserverundef Event fwu server undefined message fwuserverunreachable Event fwu server unreachable message fwusignmismatch Event fwu signature mismatch message fwusyserr Event fwu system error message fwuunsupportedhw Event fwu unsupported hardware message fwuvermismatch Event fwu version mismatch message licmgr Configures license manager module related event messages lic-installed-count Event total number of license installed count message lic-installed-default Event default license installation message lic-installed Event license installed message lic-invalid Event license installation failed message lic-removed Event license removed message mesh Configures mesh module related event messages mesh-link-down Event mesh link down message mesh-link-up Event mesh link up message <event type> <event name>
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 263 nsm Configures Network Service Module (NSM) related event message dhcpc-err Event DHCP certification error message dhcpdefrt Event DHCP defrt message dhcpip Event DHCP IP message dhcpipchg Event DHCP IP change message dhcpipnoadd Event DHCP IP overlaps static IP address message dhcplsexp Event DHCP lease expiry message dhcpnak Event DHCP server returned DHCP NAK response ifdown Event interface down message ifipcfg Event interface IP config message ifup Event interface up message pm Configures process monitor module related event messages procid Event proc ID message procmaxrstrt Event proc max restart message procnoresp Event proc no response message procrstrt Event proc restart message procstart Event proc start message procstop Event proc stop message procsysrstrt Event proc system restart message startupcomplete Event startup complete message radconf Configures RADIUS configuration daemon related event messages could-not-stop-radius Event could not stop RADIUS server message radiusdstart Event RADIUS server started message radiusdstop Event RADIUS server stopped message radio Configures radio module related event messages acs-scan-complete Event ACS scan completed acs-scan-started Event ACS scan started radar-detected Event radar detected message radar-scan-completed Event radar scan completed message radar-scan-started Event radar scan started message radio-state-change Event radio state change message resume-home-channel Event resume home channel message securitymgr Configures the security manager module related event messages deprecatedcli Event deprecated CLI message fatal-hit Event fatal hit message log-cli-error Event log CLI error message userpassstrength Event user pass strength message <event type> <event name>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 264 smrt Configures SMART RF module related event messages calibration-done Event calibration done message calibration-started Event calibration started message config-cleared Configuration cleared event message cov-hole-recovery Event coverage hole recovery message cov-hole-recovery-done Event coverage hole recovery done message interference-recovery Event interference recovery message neighbor-recovery Event neighbor recovery message power-adjustment Event power adjustment message smtpnot Configures SMTP module related event messages cfg Event cfg message cfginc Event cfg inc message net Event net message proto Event proto message smtpauth Event SMTP authentication message smtperr Event SMTP error message smtpinfo Event SMTP information message system Configures system module related event messages clock-reset Event clock reset message http Event HTTP message login Event successful login message login-fail Event login fail message. Occurs when user authentication fails. login-fail-access Event login fail access message.Occurs in case of access violation. login-fail-bad-role Event login fail bad role message. Occurs when user uses an invalid role to logon. logout Event logout message panic Event panic message procstop Event proc stop message system-autoup-disable Event system autoup disable message system-autoup-enable Event system autoup enable message ui-user-auth-fail Event user authentication fail message ui-user-auth-success Event user authentication success message <event type> <event name>
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 265 Example wm3700-37FABE(config-event-system-policy-event-testpolicy)#event aaa radius-discon-msg email on forward-to-switch default snmp default syslog default wm3700-37FABE(config-event-system-policy-event-testpolicy)# wm3700-37FABE(config-event-system-policy-adv-wips)# wm3700-37FABE(config-event-system-policy-testpolicy)#show context event-system-policy testpolicy event sole adaptererr syslog off snmp off forward-to-switch off wm3700-37FABE(config-event-system-policy-testpolicy)# Related Commands no event-system-policy mode commands Negates an event configuration test Configures the test module related event messages testalert Event test alert message testargs Event test arguments message testcrit Event test critical message testdebug Event test debug message testemerg Event test emergency message testerr Event test error message testinfo Event test information message testnotice Event test notice message testwarn Event test warning message wips Configures the Wireless IPS module related event messages wips-client-blacklisted Event WIPS client blacklisted message wips-client-rem-blacklist Event WIPS client rem blacklist message wips-event Event WIPS event triggered message email Sends e-mail notifications to a pre configured e-mail ID forward-to-switch Forwards the messages to an external server snmp Logs an SNMP event syslog Logs event to syslog default Performs the default action for the event off Switches the event off, when the event happens, no action is performed on Switches the event on, when the event happens, the configured action is taken no Resets or disables events commands <event type> <event name>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 266 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [<event type>] [<event name>] [email|forward-to-switch|snmp|syslog] [default|on|off] Parameters no event <EVENT-TYPE> <EVENT> (email,forward-to-switch,snmp,syslog) [default|on|off] <event type> <event name> aaa Resets authentication, authorization, and accounting related event messages radius-discon-msg RADIUS disconnection message radius-session-expired RADIUS session expired message radius-session-not-started RADIUS session not started message radius-vlan-update RADIUS VLAN update message
TM 4000 Series Access Point CLI Reference Guide 272 filemgmt Resets file management module related event messages http Event HTTP message httplocal Event HTTP local message https-start Event HTTPS start message https-wait Event HTTPS wait message httpstart Event HTTP start message keyadded Event key added message keydeleted Event key deleted message trustpointdeleted Event trustpoint deleted message fwu Resets firmware update related event messages fwuaborted Event aborted message fwubadconfig Event bad config message fwucorruptedfile Event corrupted file message fwucouldntgetfile Event could not get file message fwudone Event done message fwufileundef Event file undefined message fwunoneed Event no need message fwuprodmismatch Event prod mismatch message fwuserverundef Event server undefined message fwuserverunreachable Event server unreachable message fwusignmismatch Event signature mismatch message fwusyserr Event system error message fwuunsupportedhw Event unsupported hardware message fwuvermismatch Event version mismatch message licmgr Resets license manager module related event messages lic-installed-count Event total number of license installed count message lic-installed-default Event default license installation message lic-installed Event license installed message lic-invalid Event license installation failed message lic-removed Event license removed message mesh Resets mesh module related event messages mesh-link-down Event mesh link down message mesh-link-up Event mesh link up message <event type> <event name>
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 273 nsm Resets NSM related event messages dhcpc-err Event DHCP certification error message dhcpdefrt Event DHCP defrt message dhcpip Event DHCP IP message dhcpipchg Event DHCP IP change message dhcpipnoadd Event DHCP IP overlaps static IP address message dhcplsexp Event DHCP lease expiry message dhcpnak Event DHCP server returned DHCP NAK response ifdown Event interface down message ifipcfg Event interface IP config message ifup Event interface up message pm Resets process monitor module related event messages procid Event proc ID message procmaxrstrt Event proc max restart message procnoresp Event proc no response message procrstrt Event proc restart message procstart Event proc start message procstop Event proc stop message procsysrstrt Event proc system restart message startupcomplete Event startup complete message radconf Resets RADIUS configuration daemon related event messages could-not-stop-radius Event could not stop RADIUS server message radiusdstart Event RADIUS server started message radiusdstop Event RADIUS server stopped message radio Resets radio module related event messages acs-scan-complete Event ACS scan completed acs-scan-started Event ACS scan started radar-detected Event radar detected message radar-scan-completed Event radar scan completed message radar-scan-started Event radar scan started message radio-state-change Event radio state change message resume-home-channel Event resume home channel message securitymgr Resets the security manager module related event messages deprecatedcli Event deprecated CLI message fatal-hit Event fatal hit message log-cli-error Event log CLI error message userpassstrength Event user pass strength message <event type> <event name>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 274 smrt Resets SMART RF module related event messages calibration-done Event calibration done message calibration-started Event calibration started message config-cleared Configuration cleared event message cov-hole-recovery Event coverage hole recovery message cov-hole-recovery-done Event coverage hole recovery done message interference-recovery Event interference recovery message neighbor-recovery Event neighbor recovery message power-adjustment Event power adjustment message smtpnot Resets SMTP module related event messages cfg Event cfg message cfginc Event cfg inc message net Event net message proto Event proto message smtpauth Event SMTP authentication message smtperr Event SMTP error message smtpinfo Event SMTP information message system Resets system module related event messages clock-reset Event clock reset message http Event HTTP message login Event successful login message login-fail Event login fail message. Occurs when user authentication fails. login-fail-access Event login fail access message.Occurs in case of access violation. login-fail-bad-role Event login fail bad role message. Occurs when user uses an invalid role to logon. logout Event logout message panic Event panic message procstop Event proc stop message system-autoup-disable Event system autoup disable message system-autoup-enable Event system autoup enable message ui-user-auth-fail Event ui user authentication fail message ui-user-auth-success Event ui user authentication success message <event type> <event name>
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 275 Example wm3700-37FABE(config-event-system-policy-testpolicy)# wm3700-37FABE(config-event-system-policy-testpolicy)#no event aaa % Error: event_system_policy[aaa] does not exist, unable to delete wm3700-37FABE(config)# Related Commands test Resets the test module related event messages testalert Event test alert message testargs Event test arguments message testcrit Event test critical message testdebug Event test debug message testemerg Event test emergency message testerr Event test error message testinfo Event test information message testnotice Event test notice message testwarn Event test warning message wips Resets the Wireless IPS module related event messages wips-client-blacklisted Event WIPS client blacklisted message wips-client-rem-blacklist Event WIPS client rem blacklist message wips-event Event WIPS event triggered message event Configures the action taken for each event <event type> <event name>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 276 firewall-policy Global Configuration Commands Configures a firewall policy. This policy defines a set of rules for managing network traffic and prevent unauthorized access to the network behind the firewall while allowing authorized devices access. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax firewall-policy <FIREWALL-POLICY-NAME> Parameters firewall-policy <FIREWALL-POLICY-NAME> Example wm3700-37FABE(config)#firewall-policy test wm3700-37FABE(config-fw-policy-test)# Related Commands NOTE For more information on Firewall policy, see Chapter 15, Firewall Policy. <FIREWALL-POLICY-NAME> Specify the firewall policy name. If a firewall policy does not exist, it is created. no Removes an existing firewall policy
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 277 host Global Configuration Commands Enters the configuration context of a remote device using its hostname Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax host <DEVICE-NAME> Parameters host <DEVICE-NAME> Example wm3700-37FABE(config)#host wm3700-37FABE wm3700-37FABE(config-device-00-04-96-42-14-79)# <DEVICE-NAME> Specify the devices hostname. All discovered devices are displayed when Tab is pressed to auto complete this command.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 278 igmp-snoop-policy Global Configuration Commands Configures an IGMP snoop policy. IGMP snooping filters out multicast IGMP packets for those clients not subscribed to the IGMP multicast group. A wireless controller floods all ports in a IGMP broadcast domain by default. This can cause unnecessary load on host devices that have not subscribed to these streams, requiring them to process these unwanted packets. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 WM3700 Syntax igmp-snoop-policy <IGMP-SNOOP-POLICY-NAME> Parameters igmp-snoop-policy <IGMP-SNOOP-POLICY-NAME> Example wm3700-37FABE(config)#igmp-snoop-policy test wm3700-37FABE(config-igmp-snoop-policy-test)# wm3700-37FABE(config-igmp-snoop-policy-test)#? commands: igmp-snooping Enable IGMP snooping no Negate a command or set its defaults querier Configure IGMP querier robustness-variable Configure IGMP Robustness Variable unknown-multicast-fwd Forward Unknown Multicast Packet clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode <IGMP-SNOOP-POLICY- NAME> Specify the IGMP snoop policy name. This policy is created if it does not exist.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 279 exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-igmp-snoop-policy-test)# Related Commands NOTE For more information on IGMP snooping and how to configure an IGMP snooping policy, see Chapter 16, IGMP Snoop Policy. no Removes an IGMP snoop policy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 280 ip Global Configuration Commands Configures IP access control lists Access lists define access to the wireless controller managed network using a set of rules. Each rule specifies an action taken when a packet matches a given set of rules. If the action is deny, the packet is dropped. If the action is permit, the packet is allowed. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip access-list <IP-ACCESS-LIST-NAME> Parameters ip access-list <IP-ACCESS-LIST-NAME> Example wm3700-37FABE(config)#ip access-list test wm3700-37FABE(config-ip-acl-test)# wm3700-37FABE(config-ip-acl-test)#? ACL Configuration commands: deny Specify packets to reject no Negate a command or set its defaults permit Specify packets to forward clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes access-list <IP-ACCESS-LIST-NAME> Configures an IP access list <IP-ACCESS-LIST-NAME> Specify the ACL name. If the access list does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 281 service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-ip-acl-test)# Related Commands NOTE For more information on Access Control Lists, see Chapter 13, Access List. no Removes an IP access control list
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 282 l2tpv3 Global Configuration Commands Configures a Layer 2 Tunnel Protocol Version 3 (L2TPV3) tunnel policy, used to create one or more L2TPV3 tunnels. The L2TPV3 policy defines the control and encapsulation protocols needed for tunneling layer 2 frames between two IP nodes. This policy enables the creation of L2TPV3 tunnels used for transporting Ethernet frames between bridge VLANs and physical GE ports. L2TPV3 tunnels can be created between any vendor devices supporting L2TPV3 protocol. Supported in the following platforms: AP4600 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax l2tpv3 policy <L2TPV3-POLICY-NAME> Parameters l2tpv3 policy <L2TPV3-POLICY> Example wm3700-37FABE(config)#l2tpv3 policy L2TPV3Policy1 wm3700-37FABE(config-l2tpv3-policy-L2TPV3Policy1)#? L2tpv3 Policy Mode commands: cookie-size Size of the cookie field present in each l2tpv3 data message hello-interval Configure the time interval (in seconds) between l2tpv3 Hello keep-alive messages exchanged in l2tpv3 control connection no Negate a command or set its defaults reconnect-attempts Maximum number of attempts to reestablish the tunnel. reconnect-interval Time interval between the successive attempts to reestablish the l2tpv3 tunnel retry-attempts Configure the maximum number of retransmissions for signaling message retry-interval Time interval (in seconds) before the initiating a retransmission of any l2tpv3 signaling message rx-window-size Number of signaling messages that can be received l2tpv3 policy <L2TPV3-POLICY-NAME> Configures an L2TPV3 tunnel policy <L2TPV3-POLICY-NAME> Specify a policy name. The policy is created if it does not exist. To modify an existing L2TPV3, specify its name.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 283 without sending the acknowledgement tx-window-size Number of signaling messages that can be sent without receiving the acknowledgement clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands NOTE For more information on the L2TPV3 tunnel configuration mode and commands, see Chapter 26, l2tpv3-policy-commands. no Removes an existing L2TPV3 tunnel policy mint-policy Configures the global MiNT policy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 284 mac Global Configuration Commands Configures MAC access control lists Access lists define access to the wireless controller managed network using a set of rules. Each rule specifies an action taken when a packet matches a given set of rules. If the action is deny, the packet is dropped. If the action is permit, the packet is allowed. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mac access-list <MAC-ACCESS-LIST-NAME> Parameters mac access-list <MAC-ACCESS-LIST-NAME> Example wm3700-37FABE(config)#mac access-list test wm3700-37FABE(config-mac-acl-test)# wm3700-37FABE(config-mac-acl-test)#? MAC Extended ACL Configuration commands: deny Specify packets to reject no Negate a command or set its defaults permit Specify packets to forward clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes access-list <IP-ACCESS-LIST-NAME> Configures a MAC access control list <MAC-ACCESS-LIST-NAME> Specify the ACL name. If the access control list does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 285 service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-mac-acl-test)# Related Commands NOTE For more information on Access Control Lists, see Chapter 13, Access List. no Removes a MAC access control list
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 286 management-policy Global Configuration Commands Configures a management policy. This policy configures parameters, such as services that run on a device, welcome messages, banners, and others. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax management-policy <MANAGEMENT-POLICY-NAME> Parameters management-policy <MANAGEMENT-POLICY-NAME> Example wm3700-37FABE(config)#management-policy test wm3700-37FABE(config-management-policy-test)# Related Commands NOTE For more information on the parameters that can be configured in a management policy, see Chapter 17, Management Policy. <MANAGEMENT-POLICY- NAME> Specify the management policy name. If the policy does not exist, it is created. no Removes an existing management policy
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 287 mint-policy Global Configuration Commands Configures the global MiNT policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mint-policy global-default Parameters mint-policy global-default Example wm3700-37FABE(config)#mint-policy global-default wm3700-37FABE(config-mint-policy-global-default)# Related Commands NOTE For more information on MiNT policy, see Chapter 16, MINT Policy. global-default Uses the global default policy no Removes an existing MiNT policy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 288 nac-list Global Configuration Commands Configures a policy, which configures a list of devices that can access a managed network based on their MAC addresses. nac-list Global Configuration Commands Configures a Network Access Control (NAC) list that controls access to the wireless controller managed network Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax nac-list <NAC-LIST-NAME> Parameters nac-list <NAC-LIST-NAME> Example wm3700-37FABE(config)#nac-list test wm3700-37FABE(config-nac-list-test)# wm3700-37FABE(config-nac-list-test)#? NAC List Mode commands: exclude Specify MAC addresses to be excluded from the NAC enforcement list include Specify MAC addresses to be included in the NAC enforcement list Command Description Reference nac-list Creates a NAC list policy page 5-288 <NAC-LIST-NAME> Specify the NAC list name. If the NAC list does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 289 no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-nac-list-test)# Related Commands nac-list-mode The following table summarizes NAC list mode commands exclude nac-list-mode Specifies the MAC addresses excluded from the NAC enforcement list no Removes a NAC list Command Description Reference exclude Specifies the MAC addresses excluded from the NAC enforcement list page 5-289 include Specifies the MAC addresses included in the NAC enforcement list page 5-290 no Cancels an exclude or an include NAC list rule page 5-291 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 290 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax exclude <START-MAC> [<END-MAC> precedence <1-1000>|precedence <1-1000>] Parameters exclude <START-MAC> [<END-MAC> precedence <1-1000>|precedence <1-1000>] Example wm3700-37FABE(config-nac-list-test)#exclude 00-40-96-B0-BA-2A precedence 1 wm3700-37FABE(config-nac-list-test)# include nac-list-mode Specifies the MAC addresses included in the NAC enforcement list <START-MAC> Specifies a range of MAC addresses or a single MAC address to exclude from the NAC enforcement list Specify the first MAC address in the range. Use this parameter to specify a single MAC address. <END-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets the rule precedence. Exclude entries are checked in the order of their rule precedence. <1-1000> Specify a value from 1 - 1000.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 291 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax include <START-MAC> [<END-MAC> precedence <1-1000>|precedence <1-1000>] Parameters include <START-MAC> [<END-MAC> precedence <1-1000>|precedence <1-1000>] Example wm3700-37FABE(config-nac-list-test)#include 00-40-96-B0-BA-2A precedence 1 wm3700-37FABE(config-nac-list-test)# no nac-list-mode Cancels an exclude or an include NAC list rule <START-MAC> Specifies a range of MAC addresses or a single MAC address to include in the NAC enforcement list Specify the first MAC address in the range. Use this parameter to specify a single MAC address <END-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets the rule precedence. Exclude entries are checked in the order of their rule precedence. <1-1000> Specify a value from 1 - 1000.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 292 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [exclude|include] no [exclude|include] <START-MAC> [<END-MAC> precedence <1-1000>| precedence <1-1000>] Parameters no [exclude|include] <START-MAC> [<END-MAC> precedence <1-1000>| precedence <1-1000>] Example wm3700-37FABE(config-nac-list-test)#no include 00-40-96-B0-BA-2A precedence 1 rwm3700-37FABE(config-nac-list-test)#show context nac-list test wm3700-37FABE(config-nac-list-test)# Related Commands no exclude Removes an exclude rule no include Removes an include rule <START-MAC> Specifies a range of MACs included in/removed from the NAC enforcement list Specify the first MAC address in the range. Use this parameter to specify a single MAC address. <END-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets the rule precedence for this rule. Exclude entries are checked in the order of their rule precedence. <1-1000> Specify a value from 1 - 1000. exclude Specifies MAC addresses excluded from the NAC enforcement list include Specifies MAC addresses included in the NAC enforcement list
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 293 no Global Configuration Commands Negates a command, or reverts configured settings to their default values Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no <parameter> Parameters None Example wm3700-37FABE(config)#no ? aaa-policy Delete a aaa policy advanced-wips-policy Delete an advanced-wips policy ap4021 Delete an AP4021 access point ap4600 Delete an AP4600 access point ap4511 Delete an AP4511 access point ap4521 Delete an AP4521 access point ap4532 Delete an AP4532 access point ap4700 Delete an AP4700 access point association-acl-policy Delete an association-acl policy auto-provisioning-policy Delete an auto-provisioning policy captive-portal Delete a captive portal critical-resource-policy Remove device onboard critical resource policy customize Restore the custom cli commands to default device Delete multiple devices device-categorization Delete device categorization object dhcp-server-policy DHCP server policy dns-whitelist Delete a whitelist object event-system-policy Delete a event system policy firewall-policy Configure firewall policy igmp-snoop-policy Remove device onboard igmp snoop policy ip Internet Protocol (IP)
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 294 mac MAC configuration management-policy Delete a management policy nac-list Delete an network access control list password-encryption Disable password encryption in configuration profile Delete a profile and all its associated configuration radio-qos-policy Delete a radio QoS configuration policy radius-group Local radius server group configuration radius-server-policy Remove device onboard radius policy radius-user-pool-policy Configure Radius User Pool rf-domain Delete one or more RF-domains and all their associated configurations WM3400 Delete an wm3400 wireless controller WM3600 Delete an wm3600 wireless controller WM3700 Delete an wm3700 wireless controller role-policy Role based firewall policy smart-rf-policy Delete a smart-rf-policy wips-policy Delete a wips policy wlan Delete a wlan object wlan-qos-policy Delete a wireless lan QoS configuration policy service Service Commands wm3700-37FABE(config)#
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 295 password-encryption Global Configuration Commands Enables password encryption within a configuration Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax password-encryption secret 2 <LINE> Parameters password-encryption secret 2 <LINE> Example wm3700-37FABE(config)#password-encryption secret 2 extreme wm3700-37FABE(config)# secret 2 <LINE> Encrypts passwords with a secret phrase 2 Specifies the encryption type as either SHA256 or AES256 <LINE> Specify the encryption passphrase.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 296 profile Global Configuration Commands Configures profile related commands. If no parameters are given, all profiles are selected. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax profile {ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|containing|filter| wm3400|wm3600|wm3700} profile {ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|wm3400|wm3600|wm3700} [<DEVICE-PROFILE-NAME>] profile {containing [<DEVICE-PROFILE-NAME>] {filter [type [ap4021|ap4600|ap4511| ap4521|ap4532|ap4700|wm3400|wm3600|wm3700]]}} profile {filter [type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|wm3400| wm3600|wm3700]]} Parameters profile {ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|containing|filter| wm3400|wm3600|wm3700} [<DEVICE-PROFILE-NAME>] profile Configures device profile commands. If no device profile is specified, the system configures all device profiles. ap4021 Optional. Configures AP4021 profile commands ap4600 Optional. Configures AP4600 profile commands ap4511 Optional. Configures AP4511 profile commands ap4521 Optional. Configures AP4521 profile commands ap4532 Optional. Configures AP4532 profile commands ap4700 Optional. Configures AP4700 profile commands wm3400 Optional. Configures WM3400 profile commands wm3600 Optional. Configures WM3600 profile commands wm3700 Optional. Configures WM3700 profile commands
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 297 profile {containing [<DEVICE-PROFILE-NAME>] {filter [type [ap4021|ap4600|ap4511| ap4521|ap4532|ap4700|wm3400|wm3600|wm3700]]}} profile {filter [type [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700|wm3400| wm3600|wm3700]]} Example wm3700-37FABE(config)#profile WM3700 test1 wm3700-37FABE(config-profile-test1)#? Profile Mode commands: <DEVICE-PROFILE- NAME> After specifying the profile type, specify a substring in the profile name to filter profiles profile Configures device profile commands containing <DEVICE-PROFILE- NAME> Optional. Configures profiles that contain a specified sub-string in the hostname <DEVICE-PROFILE-NAME> Specify a substring in the profile name to filter profiles. filter type Optional. An additional filter used to configure a specific type of device profile. If no device type is specified, the system configures all device profiles. type Filters profiles by the device type. Select a device type from the following options: ap4021 Selects a AP4021 profile ap4600 Selects a AP4600 profile ap4511 Selects a AP4511 profile ap4521 Selects a AP4511 profile ap4532 Selects a AP4532 profile ap4700 Selects a AP4700 profile wm3400 Selects a WM3400 profile wm3600 Selects a WM3600 profile wm3700 Selects a WM3700 profile profile Configures device profile commands filter type Optional. An additional filter used to configure a specific type of device profile. If no device type is specified, the system configures all device profiles. type Filters profiles by the device type. Select a device type from the following options: ap4021 Selects a AP4021 profile ap4600 Selects a AP4600 profile ap4511 Selects a AP4511 profile ap4521 Selects a AP4521 profile ap4532 Selects a AP4532 profile ap4700 Selects a AP4700 profile wm3400 Selects a WM3400 profile wm3600 Selects a WM3600 profile wm3700 Selects a WM3700 profile
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 298 aaa VPN AAA authentication settings adopted-mode Set Device Running in Adopted Mode ap-upgrade AP firmware upgrade arp Address Resolution Protocol (ARP) auto-learn-staging-config Enable learning network configuration of the devices that come for adoption autoinstall Autoinstall Configuration commands bridge Ethernet bridge cdp Cisco Discovery Protocol cluster Cluster configuration configuration-persistence Enable persistence of configuration across reloads (startup config file) controller WLAN controller configuration crypto Encryption related commands dscp-mapping Configure IP DSCP to 802.1p priority mapping for untagged frames email-notification Email notification configuration enforce-version Check the firmware versions of devices before interoperating events System event messages interface Select an interface to configure ip Internet Protocol (IP) led Turn LEDs on/off on the device legacy-auto-downgrade Enable device firmware to auto downgrade when other legacy devices are detected legacy-auto-update Enable legacy device firmware auto update lldp Link Layer Discovery Protocol load-balancing Configure load balancing parameter local Local user authentication database for VPN logging Modify message logging facilities mac-address-table MAC Address Table mint MiNT protocol misconfiguration-recovery-time Check controller connectivity after configuration is received monitor Critical resource monitoring neighbor-inactivity-timeout Configure neighbor inactivity timeout neighbor-info-interval Configure neighbor information exchange interval no Negate a command or set its defaults noc Configure the noc related setting ntp Ntp server A.B.C.D power-config Configure power mode preferred-controller-group Controller group this system will prefer for adoption radius Configure device-level radius authentication parameters rf-domain-manager RF Domain Manager
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 299 spanning-tree Spanning tree use Set setting to use vpn Vpn configuration wep-shared-key-auth Enable support for 802.11 WEP shared key authentication clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-profile-test1)# NOTE For more information on profiles and how to configure profiles, see Chapter 8, Profiles.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 300 radio-qos-policy Global Configuration Commands Configures a radio quality-of-service (QoS) policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radio-qos-policy <RADIO-QOS-POLICY-NAME> Parameters radio-qos-policy <RADIO-QOS-POLICY-NAME> Example wm3700-37FABE(config)#radio-qos-policy test wm3700-37FABE(config)# NOTE For more information on radio qos policy, see Chapter 19, Radio QoS Policy. <RADIO-QOS-POLICY- NAME> Specify the radio QoS policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 301 radius-group Global Configuration Commands Configures RADIUS user group parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radius-group <RADIUS-GROUP-NAME> Parameters radius-group <RADIUS-GROUP-NAME> Example wm3700-37FABE(config)#radius-group testgroup wm3700-37FABE(config)# NOTE For more information on RADIUS user group commands, see Chapter 18, RADIUS Policy. <RADIUS-GROUP-NAME> Specify a RADIUS user group name. The name should not exceed 64 characters. If the RADIUS user group does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 302 radius-server-policy Global Configuration Commands Creates an onboard device RADIUS policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radius-server-policy <RADIUS-SERVER-POLICY-NAME> Parameters radius-server-policy <RADIUS-SERVER-POLICY-NAME> Example wm3700-37FABE(config)#radius-server-policy testpolicy wm3700-37FABE(config)# NOTE For more information on RADIUS user group commands, see Chapter 18, RADIUS Policy. <RADIUS-SERVER- POLICY-NAME> Specify the RADIUS server policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 303 radius-user-pool-policy Global Configuration Commands Configures a RADIUS user pool Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radius-user-pool-policy <RADIUS-USER-POOL-POLICY-NAME> Parameters radius-user-pool-policy <RADIUS-USER-POOL-POLICY-NAME> Example wm3700-37FABE(config)#radius-user-pool-policy testpool wm3700-37FABE(config)# NOTE For more information on RADIUS user group commands, see Chapter 18, RADIUS Policy. <RADIUS-USER-POOL- POLICY-NAME> Specify the RADIUS user pool policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 304 rf-domain Global Configuration Commands An RF Domain groups devices that can logically belong to one network. The RF Domain policy configures a set of parameters that enable devices configured quickly as belonging to a particular RF Domain. rf-domain rf-domain Creates a RF Domain or enters RF Domain context for one or more RF Domains. If the policy does not exist, it creates a new policy. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rf-domain {<RF-DOMAIN-NAME>|containing <DOMAIN-NAME>} Parameters rf-domain {<RF-DOMAIN-NAME>|containing <DOMAIN-NAME>} Command Description Reference rf-domain Creates a RF Domain policy page 5-304 rf-domain Creates a new RF Domain or enters RF Domain context for one or more existing RF Domains <RF-DOMAIN-NAME> Specify the RF Domain name. The name should not exceed 32 characters and should represent the intended purpose. Once created, the name cannot be edited. containing <DOMAIN-NAME> Specify an existing RF Domain that contains a specified sub-string in the domain name <DOMAIN-NAME> Specify a sub-string of the RF Domain name.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 305 Example wm3700-37FABE(config)#rf-domain WM3700 wm3700-37FABE(config-rf-domain-WM3700)# WM3400-880DA7(config)#rf-domain default WM3400-880DA7(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-WM3700)#? RF Domain Mode commands: channel-list Configure channel list to be advertised to wireless clients contact Configure the contact control-vlan VLAN for control traffic on this RF Domain country-code Configure the country of operation dhcp-redundancy Enable DHCP redundancy layout Configure layout location Configure the location mac-name Configure MAC address to name mappings no Negate a command or set its defaults override-smartrf Configured RF Domain level overrides for smart-rf override-wlan Configure RF Domain level overrides for wlan sensor-server AirDefense sensor server configuration stats Configure the stats related setting timezone Configure the timezone use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-rf-domain-WM3700)# rf-domain-mode rf-domain This section describes the default commands under RF Domain. The following table summarises RF Domain commands Command Description Reference channel-list Configures the channel list advertised by radios page 5-306 contact Configures details of the person to contact (the network administrator) in case of any problems impacting the RF Domain page 5-308 control-vlan Configures VLAN for traffic control on a RF Domain page 5-309
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 306 channel-list rf-domain-mode Configures the channel list advertised by radios. This command also enables dynamic update of a channel list country-code Configures the country of operation page 5-310 dhcp-redundancy Enables DHCP redundancy on a RF Domain page 5-311 layout Configures layout information page 5-311 location Configures the physical location of a RF Domain page 5-313 mac-name Maps MAC addresses to names page 5-314 no Negates a command or reverts configured settings to their default values page 5-315 override-smart-rf Configures RF Domain level overrides for Smart RF page 5-316 override-wlan Configures RF Domain level overrides for WLAN page 5-318 sensor-server Configures a AirDefense sensor server on this RF Domain page 5-319 stats Configures stats related settings on this RF Domain. These settings define how RF Domain statistics are updated page 5-320 timezone Configures a RF Domains geographic time zone page 5-321 use Enables the use of a specified Smart RF and/or WIPS policy page 5-322 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 307 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax channel-list [2.4GHz|5GHz|dynamic] channel-list dynamic channel-list [2.4GHz|5GHz] <CHANNEL-LIST> Parameters channel-list dynamic channel-list [2.4GHz|5GHz] <CHANNEL-LIST> Example wm3700-37FABE(config-rf-domain-default)#channel-list 2.4GHz 1-10 wm3700-37FABE(config-rf-domain-default)#show context rf-domain RFDOMAIN_UseCase1 location SanJose contact [email protected] timezone America/Los_Angeles country-code us channel-list 2.4GHz 1,2,3,4,5,6,7,8,9,10 wm3700-37FABE(config-rf-domain-default)# dynamic Enables dynamic update of a channel list 2.4GHz <CHANNEL-LIST> Configures the channel list advertised by radios operating in the 2.4GHz mode <CHANNLE-LIST> Specify the list of channels separated by commas or hyphens. 5GHz <CHANNEL-LIST> Configures the channel list advertised by radios operating in the 5GHz mode <CHANNLE-LIST> Specify the list of channels separated by commas or hyphens.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 308 Related Commands contact rf-domain-mode Configures the contact (the network administrator) in case of problems or issues impacting the RF Domain Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax contact <WORD> Parameters contact <WORD> Example wm3700-37FABE(config-rf-domain-default)#contact Bob+919620011529 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default contact Bob+919620011529 stats update-interval 200 no country-code use smart-rf-policy Smart-RF1 use wips-policy WIPS1 sensor-server 2 ip 172.16.10.3 override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)# no Removes the list of channels configured on the selected RF Domain for 2.4GHz and 5GHz bands. Also disables dynamic update of a channel list. contact <WORD> Specify contact details, such as name and number.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 309 Related Commands control-vlan rf-domain-mode Configures VLAN for traffic control in this RF Domain Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax control-vlan <1-4094> Parameters control-vlan <1-4094> Example wm3700-37FABE(config-rf-domain-default)#control-vlan 1 wm3700-37FABE(config-rf-domain-default)#show context rf-domain RFDOMAIN_UseCase1 location SanJose contact [email protected] timezone America/Los_Angeles country-code us channel-list 2.4GHz 1,2,3,4,5,6,7,8,9,10 control-vlan 1 wm3700-37FABE(config-rf-domain-default)# no Removes contact details configured for a RF Domain <1-4094> Specify the VLAN ID from 1 - 4094.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 310 Related Commands country-code rf-domain-mode Configures a RF Domains country of operation. Since device channels transmit in specific channels unique to the country of operation, it is essential to configure the country code correctly or risk using the access point illegally. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax country-code [<WORD>] Parameters country-code [<WORD>] Example wm3700-37FABE(config-rf-domain-default)#country-code in wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default country-code in wm3700-37FABE(config-rf-domain-default)# no Disables the VLAN for controlling traffic in a RF Domain country-code Configures the RF Domains country of operation <WORD> Specify the 2 letter ISO-3166 country code.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 311 Related Commands dhcp-redundancy rf-domain-mode Enables DHCP redundancy in this RF Domain Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-redundancy Parameters None Example wm3700-37FABE(config-rf-domain-default)#dhcp-redundancy wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default country-code in dhcp-redundancy wm3700-37FABE(config-rf-domain-default)# Related Commands layout rf-domain-mode no Removes the country of operation configured on a RF Domain no Removes RF Domain DHCP redundancy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 312 Configures the RF Domain layout in terms of area, floor, and location on a map. It allows users to place APs across the deployment map. A maximum of 256 layouts is permitted. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax layout [area|floor|map-location] layout [area|floor|map-location] {(area [<AREA-NAME>]|floor [<FLOOR-NAME>]| map-location [<URL> units [feet|meters] {area [<AREA-NAME>]|floor [<FLOOR- NAME>]}} Parameters layout [area|floor|map-location] {(area [<AREA-NAME>]|floor [<FLOOR-NAME>]| map-location [<URL> units [feet|meters] {area [<AREA-NAME>]|floor [<FLOOR- NAME>]}} Example wm3700-37FABE(config-rf-domain-default)#layout map-location www.firstfloor.com units meters area Ecospace floor Floor5 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context layout Configures the RF Domain layout in terms of area, floor, and location on a map area <AREA-NAME> Configures the RF Domain area name <AREA-NAME> Specify the area name. floor <FLOOR-NAME> Configures the RF Domain floor name <FLOOR-NAME> Specify the floor name. map-location <URL> units [feet|meters] Configures the location of the RF Domain on the map <URL> Specify the URL to configure the map location. units Configures the map units in terms of feet or meters feet Selects the unit of measurement as feet meters Selects the unit of measurement as meters
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 313 rf-domain default country-code us sensor-server 1 ip 172.16.10.14 port 1 channel-list dynamic channel-list 2.4GHz 1,2,3,4,5,6,7,8,9,10 layout map-location www.firstfloor.com units meters area Ecospace floor Floor5 wm3700-37FABE(config-rf-domain-default)# Related Commands location rf-domain-mode Configures the physical location of the wireless controller RF Domain. The location could be as specific as the building name or floor number. Or it could be generic and include an entire site. The location defines the physical area where a common set of device configurations are deployed and managed by a RF Domain policy. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax location <WORD> Parameters location <WORD> Example wm3700-37FABE(config-rf-domain-default)#location SanJose wm3700-37FABE(config-rf-domain-default)# no Removes the RF Domain layout details location <WORD> Configures the RF Domain location by specifying the area or building name <WORD> Specify the location.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 314 wm3700-37FABE(config-rf-domain-default)#show context rf-domain default location SanJose no country-code wm3700-37FABE(config-rf-domain-default)# Related Commands mac-name rf-domain-mode Configures a relevant name for each MAC address Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mac-name <MAC> <NAME> Parameters mac-name <MAC> <NAME> Example wm3700-37FABE(config-rf-domain-default)#mac-name 11-22-33-44-55-66 TestDevice wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context no Removes the RF Domain location mac-name Configures a relevant name for each MAC address <MAC> <NAME> Specifies the MAC address <NAME> Specify a friendly name for this MAC address to use in events and statistics.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 315 rf-domain default location SanJose no country-code mac-name 11-22-33-44-55-66 TestDevice wm3700-37FABE(config-rf-domain-default)# Related Commands no rf-domain-mode Negates a command or reverts configured settings to their default. When used in the config RF Domain mode, the no command negates or reverts RF Domain settings. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [channel-list|contact|control-vlan|country-code|dhcp- redundancy|layout|location| mac-name|override-smartrf|override-wlan|sensor- server|stats|timezone|use] Parameters no [channel-list|contact|control-vlan|country-code|dhcp-redundancy|layout| location|mac-name|override-smartrf|override-wlan|sensor- server|stats|timezone| use] no Removes the MAC address to name mapping no channel-list Removes the channel list for 2.4GHz and 5GHz bands. Also disables dynamic update of a channel list no contact Removes contact details configured no control-vlan Removes VLAN configured for controlling traffic no country-code Removes the country of operation configured no dhcp-redundancy Removes DHCP redundancy
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 316 Example wm3700-37FABE(config-rf-domain-default)#mac-name 11-22-33-44-55-66 TestDevice wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default location SanJose no country-code mac-name 11-22-33-44-55-66 TestDevice wm3700-37FABE(config-rf-domain-default)# Related Commands override-smart-rf rf-domain-mode Configures RF Domain level overrides for a Smart RF policy no layout Removes the RF Domain layout details no location Removes the RF Domain location details no mac-name Removes the MAC address to name mapping no override-smartrf Resets the override Smart RF settings to default no override-wlan Resets the override WLAN settings to default no sensor-server Disables a AirDefense sensor server details no stats Resets RF Domain stats settings no timezone Removes the RF Domains time zone no use Resets RF Domain profile settings channel-list Configures the channel list advertised by radios, and enables dynamic update of channel lists contact Configures details of the person to contact (or the administrator) in case of any problems or issues impacting the RF Domain control-vlan Configures a VLAN for traffic control country-code Configures a RF Domains country of operation dhcp-redundancy Enables a RF Domains DHCP redundancy layout Configures a RF Domains layout maps location Configures a RF Domains deployment location mac-name Configures a relevant name for each MAC address override-smart-rf Configures RF Domain level overrides for Smart RF override-wlan Configures RF Domain level overrides for WLAN sensor-server Configures a AirDefense sensor server stats Configures RF Domain stats settings timezone Configures a RF Domains geographic time zone use Enables the use of a Smart RF and/or WIPS policy
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 317 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax override-smartrf channel-list [2.4GHz|5GHZ] <WORD> Parameters override-smartrf channel-list [2.4GHz|5GHZ] <WORD> Example wm3700-37FABE(config-rf-domain-default)#override-smartrf channel-list 2.4GHz 1 ,2,3 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default location SanJose no country-code override-smartrf channel-list 2.4GHz 1,2,3 mac-name 11-22-33-44-55-66 TestDevice wm3700-37FABE(config-rf-domain-default)# override-smartrf Configures RF Domain level overrides for a Smart RF policy channel-list Enables the selection of a channel list for a Smart RF policy 2.4GHz <WORD> Selects the 2.4GHz band <WORD> Specify a list of channels separated by commas. 5GHz <WORD> Selects the 5GHz band <WORD> Specify a list of channels separated by commas.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 318 Related Commands override-wlan rf-domain-mode Configures RF Domain level overrides for a WLAN Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax overrides-wlan <WLAN> [ssid|vlan-pool|wpa-wpa2-psk] overrides-wlan <WLAN> [ssid <SSID>|vlan-pool <1-4094> {limit}|wpa-wpa2-psk <WORD>] Parameters overrides-wlan <WLAN> [ssid <SSID>|vlan-pool <1-4094> {limit}|wpa-wpa2-psk <WORD>] no Resets the override Smart RF settings its default <WLAN> Configures the WLAN name The name should not exceed 32 characters and should represent the WLAN coverage area. After creating the WLAN, configure its override parameters. ssid <SSID> Configures a override Service Set Identifier (SSID) associated with this WLAN The SSID should not exceed 32 characters. vlan-pool <1-4094> limit Configures the override VLANs available to this WLAN <1-4094> Specify the VLAN ID from 1 - 4094. limit Optional. Sets a limit to the number of users on this VLAN. The maximum client limit is 8192 per VLAN. The default is 0. wpa-wpa2-psk <WORD> Configures the WPA-WPA2 key or passphrase for this WLAN <WORD> Specify a WPA-WPA2 key or passphrase.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 319 Example wm3700-37FABE(config-rf-domain-default)#override-wlan test vlan-pool 2 limit 2 0 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default no country-code override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)# Related Commands sensor-server rf-domain-mode Configures a AirDefense sensor server on this RF Domain. Sensor servers allow network administrators to monitor and download data from multiple sensors remote locations using Ethernet TCP/IP or serial communications. This enables administrators to respond quickly to interferences and coverage problems. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax sensor-server <1-3> ip <IP> port [443|8443|<1-65535>] Parameters sensor-server <1-3> ip <IP> port [443|8443|<1-65535>] no Resets the override WLAN settings its default Sensor-server <1-3> Configures a AirDefense sensor server parameters <1-3> Select the server ID from 1 - 3. The server with the lowest defined ID is reached first by the wireless controller. The default is 1.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 320 Example wm3700-37FABE(config-rf-domain-default)#sensor-server 2 ip 172.16.10.3 port 44 3 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default no country-code sensor-server 2 ip 172.16.10.3 override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)# Related Commands stats rf-domain-mode Configures stats settings that define how RF Domain statistics are updated Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax stats [open-window|update-interval ip <IP> Configures the (non DNS) IP address of the sensor server <IP> Specify the IP address of the sensor server. port [443|8443|<1-65535>] Configures the sensor server port. The options are: 443 Configures port 443, the default port used by the AirDefense server 8843 Configures port 883, the default port used by advanced WIPS on a wireless controller <1-6553> Allows you to select a WIPS/AirDefense sensor server port from 1 - 65535 no Disables a AirDefense sensor server parameters
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 321 stats open-window <1-2> {sample-interval [<5-86640>] {size [<3-100>]}} stats update-interval [<5-300>|auto]] Parameters stats open-window <1-2> {sample-interval [<5-86640>] {size [<3-100>]}} stats update-interval [<5-300>|auto] Example wm3700-37FABE(config-rf-domain-default)#stats update-interval 200 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)*#show context rf-domain default stats update-interval 200 no country-code sensor-server 2 ip 172.16.10.3 override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)*# Related Commands timezone rf-domain-mode stats Configures stats related settings on this RF Domain open-window <1-2> Opens a stats window to get trending data <1-2> Configures a numerical index ID for this RF Domain statistics sample-interval <5-86640> Optional. Configures the interval at which the wireless controller captures statistics supporting this RF Domain <5-86640> Specify the sample interval from 5 - 86640 seconds. The default is 5 seconds. size <3-100> Optional. After specifying the interval time you might specify the number of samples used by the wireless controller to define RF Domain statistics. <3-100> Specify the number of samples from 3 - 100. The default is 6 samples. stats Configures stats related settings on this RF Domain update-interval [<5-300>|auto] Configures the interval at which RF Domain statistics are updated. The options are: <5-300> Specify an update interval from 5 - 300 seconds. auto The RF Domain manager automatically adjusts the update interval based on the load. no Resets stats related settings
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 322 Configures the RF Domains geographic time zone. Configuring the time zone is essential for RF Domains deployed across different geographical locations. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax timezone <TIMEZONE> Parameters timezone <TIMEZONE> Example wm3700-37FABE(config-rf-domain-default)#timezone America/Los_Angeles wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default timezone America/Los_Angeles stats update-interval 200 no country-code use wips-policy WIPS1 sensor-server 2 ip 172.16.10.3 override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)# Related Commands use rf-domain-mode Enables the use of Smart RF and WIPS with this RF Domain time <TIMEZONE> Specify the RF Domains time zone. no Removes a RF Domains time zone
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 323 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [smart-rf-policy|wips-policy] use [smart-rf-policy <SMART-RF-POLICY-NAME>|wips-policy <WIPS-POLICY-NAME>] Parameters use [smart-rf-policy <SMART-RF-POLICY-NAME>|wips-policy <WIPS-POLICY-NAME>] Example wm3700-37FABE(config-rf-domain-default)#use smart-rf-policy Smart-RF1 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#use wips-policy WIPS1 wm3700-37FABE(config-rf-domain-default)# wm3700-37FABE(config-rf-domain-default)#show context rf-domain default stats update-interval 200 no country-code use smart-rf-policy Smart-RF1 use wips-policy WIPS1 sensor-server 2 ip 172.16.10.3 override-wlan test vlan-pool 2 limit 20 wm3700-37FABE(config-rf-domain-default)# use Uses a Smart RF policy with this RF Domain smart-rf-policy <SMART-RF-POLICY- NAME> Specifies a Smart RF policy <SMART-RF-POLICY-NAME> Specify the Smart RF policy name. wips-policy <WIPS-POLICY-NAME> Specifies a WIPS policy <WIPS-POLICY-NAME> Specify the WIPS policy name.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 324 Related Commands no Resets profiles used with this RF Domain
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 325 wm3400 Global Configuration Commands Adds an WM3400 wireless controller to the network Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wm3400 <DEVICE-WM3400> Parameters wm3400 <DEVICE-WM3400> Example wm3700-37FABEconfig)#WM3400 10-20-30-40-50-60 wm3700-37FABE(config-device-10-20-30-40-50-60)# <DEVICE-wm3400> Specify the MAC address of the WM3400.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 326 wm3600 Global Configuration Commands Adds an WM3600 wireless controller to the network Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wm3600 <DEVICE-WM3600> Parameters wm3600 <DEVICE-WM3600> Example wm3700-37FABE(config)#WM3600 11-20-30-40-50-61 wm3700-37FABE(config-device-11-20-30-40-50-61)# <DEVICE-wm3600> Specify the MAC address of a WM3600.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 327 wm3700 Global Configuration Commands Adds an WM3700 wireless controller to the network Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wm3700 <DEVICE-WM3700> Parameters wm3700 <DEVICE-WM3700> Example wm3700-37FABE(config)#WM3700 12-20-30-40-50-62 wm3700-37FABE(config-device-12-20-30-40-50-62)# <DEVICE-wm3700> Specify the MAC address of a WM3700.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 328 role-policy Global Configuration Commands Configures a role-based firewall policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax role-policy <ROLE-POLICY-NAME> Parameters role-policy <ROLE-POLICY-NAME> Example wm3700-37FABE(config)#role-policy role1 wm3700-37FABE(config)# NOTE For more information on Role policy commands, see Chapter 20, Role Policy. <ROLE-POLICY-NAME> Specify the role policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 329 self Global Configuration Commands Displays the devices configuration context Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax self Parameters None Example wm3700-37FABE(config)#self wm3700-37FABE(config-device-00-15-70-37-FA-BE)#
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 330 smart-rf-policy Global Configuration Commands Configures a Smart RF policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax smart-rf-policy <SMART-RF-POLICY-NAME> Parameters smart-rf-policy <SMART-RF-POLICY-NAME> Example wm3700-37FABE(config)#smart-rf-policy test wm3700-37FABE(config-smart-rf-policy-test)# NOTE For more information on smart-rf policy commands, see Chapter 21, Smart RF Policy. <SMART-RF-POLICY- NAME> Specify the Smart RF policy name. If the policy does not exist, it is created.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 331 wips-policy Global Configuration Commands Configures a WIPS policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wips-policy <WIPS-POLICY-NAME> Parameters wips-policy <WIPS-POLICY-NAME> Example wm3700-37FABE(config)#wips-policy test wm3700-37FABE(config-wips-policy-test)# NOTE For more information on WIPS policy commands, see Chapter 22, WIPS Policy. <WIPS-POLICY-NAME> Specify the WIPS policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 332 wlan Global Configuration Commands Configures a wireless LAN wlan wlan Configures a WLAN or enters WLAN configuration context for one or more WLANs Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wlan {<WLAN-NAME>|containing <WLAN-NAME>} Parameters wlan {<WLAN-NAME>|containing <WLAN-NAME>} Example wm3700-37FABE(config)#wlan 1 wm3700-37FABE(config-wlan-1)# wm3700-37FABE(config)#wlan containing wlan1 wm3700-37FABE(config-wlan-{'containing': 'wlan1'})# Command Description Reference wlan Configures a wireless LAN page 5-304 wlan <WLAN-NAME> Configures a new wireless LAN <WLAN-NAME> Optional. Specify the WLAN name. containing <WLAN-NAME> Optional. Configures an existing WLANs configuration context <WLAN-NAME> Specify a sub-string in the WLAN name. Use this parameter to filter a WLAN
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 333 wlan-mode commands wlan Configures WLAN mode commands. Manual WLAN mappings are erased when the actual WLAN is disabled and then enabled immediately Use the (config) instance to configure WLAN related parameters. To navigate to this instance, use the following commands: wm3700-37FABE(config)#wlan <WLAN> The following table summarizes WLAN mode commands Command Description Reference 802.11w Enables support for Protected Management Frame (IEEE 802.11w) settings page 5-334 accounting Defines WLAN accounting configuration page 5-335 acl Defines the actions based on an ACL rule configuration page 5-336 answer- broadcast-probes Allows a WLAN to respond to probes for broadcast ESS page 5-337 authentication- type Sets a WLANs authentication type page 5-338 bridging-mode Configures how packets to/from this WLAN are bridged page 5-339 broadcast-dhcp Configures broadcast DHCP packet handling page 5-340 broadcast-ssid Advertises a WLANs SSID in beacons page 5-341 captive-portal- enforcement Configures a WLANs captive portal enforcement page 5-342 client-access Enables WLAN client access (normal data operations) page 5-343 client-client- communication Allows the switching of frames from one wireless client to another on a WLAN page 5-344 client-load- balancing Enables load balancing of WLAN clients page 5-344 data-rates Specifies the 802.11 rates supported on the WLAN page 5-346 description Sets a WLANs description page 5-349 encryption-type Sets a WLANs encryption type page 5-350 enforce-dhcp Drops packets from clients with a static IP address page 5-351 ip Configures IP settings page 5-352 kerberos Configures Kerberos authentication parameters page 5-354 motorola- extensions Enables support for Motorola-specific extensions to 802.11 page 5-356 no Negates a command or sets its default value page 5-357 proxy-arp-mode Enables the proxy ARP mode for ARP requests page 5-360 radius Configures the RADIUS related parameters page 5-361 shutdown Closes a WLAN page 5-363 ssid Configures a WLANs SSID page 5-363 use Defines WLAN mode configuration settings page 5-364 vlan Sets VLAN assignment for a WLAN page 5-366
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 334 802.11w wlan-mode commands Enables support for Protected Management Frames (PMF) (IEEE 802.11w) settings Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax 802.11w [mandatory|optional|sa-query] 802.11w [mandatory|optional] 802.11w sa-query [attempts <1-15>|timeout <100-6000>] Parameters 802.11w [mandatory|optional] 802.11w sa-query [attempts <1-15>|timeout <100-6000>] vlan-pool- member Adds a member VLAN to the pool of VLANs for a WLAN page 5-367 wep128 Configures WEP128 parameters page 5-369 wep64 Configures WEP64 parameters page 5-370 wireless-client Configures the transmit power for wireless clients transmission page 5-371 wpa-wpa2 Modifies TKIP and CCMP (WPA/WPA2) related parameters page 5-373 802.11w mandatory Enforces WLAN PMF settings 802.11w optional Advertises support for PMF, but it is enforced only for clients that indicate their support 802.11w sa-query Enables security association (SA) query settings attempts <1-15> Sets the number of times an SA query message is attempted time-out <100-600> Sets the timeout period, when waiting for a response to an sa query, before re- sending Command Description Reference
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 335 Example wm3700-37FABE(config-wlan-wlan1)#802.11w sa-query timeout 110 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#802.11w sa-query attempts 1 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode tunnel encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 wm3700-37FABE(config-wlan-wlan1)# accounting wlan-mode commands Defines the WLANs accounting configuration Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accounting [radius|syslog] accounting radius accounting [syslog host <IP/HOSTNAME> {port [<1-65535>]}] Parameters accounting radius accounting radius Enables support for WLAN RADIUS accounting messages
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 336 accounting [radius|syslog host <IP/HOSTNAME> {port [<1-65535>]}] Example wm3700-37FABE(config-wlan-wlan1)#accounting syslog host 172.16.10.12 port 2 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode tunnel encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 wm3700-37FABE(config-wlan-wlan1)# acl wlan-mode commands Defines the actions taken based on an ACL rule configuration Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax acl exceed-rate wireless-client-denied-traffic <0-1000000> {blacklist |disassociate} acl exceed-rate wireless-client-denied-traffic <0-1000000> {blacklist <0-86400>|disassociate} accounting syslog Enables support for WLAN syslog accounting messages host <IP/HOSTNAME> Configures a syslog destination hostname or IP address for accounting records <IP/HOSTNAME> Specify the IP address or name of the destination host. port <1-65535> Optional. Configures the syslog servers UDP port (this port is used to connect to the server) <1-65535> Specify the port from 1 - 65535.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 337 Parameters acl exceed-rate wireless-client-denied-traffic <0-1000000> {blacklist <0-86400>|disassociate} Example wm3700-37FABE(config-wlan-wlan1)#acl exceed-rate wireless-client-denied- traffic 20 disassociate wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode tunnel encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 acl exceed-rate wireless-client-denied-traffic 20 disassociate wm3700-37FABE(config-wlan-wlan1)# answer-broadcast-probes wlan-mode commands Allows the WLAN to respond to probe requests that do not specify an SSID. These probes are for broadcast ESS. acl exceed-rate Sets the actions taken based on an ACL rule configuration (for example, drop a packet) exceed-rate Action is taken when the rate exceeds a specified value wireless-client-denied- traffic <0-1000000> Sets the action to deny traffic to the wireless client, when the rate exceeds the specified value <0-1000000> Specify a allowed rate threshold of disallowed traffic in packets/sec. blacklist <0-86400> Optional. When enabled, sets the time interval to blacklist a wireless client disassociate Optional. When enabled, disassociates a wireless client
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 338 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax answer-broadcast-probes Parameters None Example wm3700-37FABE(config-wlan-wlan1)#answer-broadcast-probes wm3700-37FABE(config-wlan-wlan1)# authentication-type wlan-mode commands Sets the WLANs authentication type Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication-type [eap|eap-mac|eap-psk|kerberos|mac|none]
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 339 Parameters authentication-type [eap|eap-mac|eap-psk|kerberos|mac|none] Example wm3700-37FABE(config-wlan-wlan1)#authentication-type eap wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode tunnel encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 acl exceed-rate wireless-client-denied-traffic 20 disassociate wm3700-37FABE(config-wlan-wlan1)# bridging-mode wlan-mode commands Configures how packets are bridged to and from a WLAN authentication-type Configures a WLANs authentication type The authentication types are: EAP, EAP-MAC, EAP-PSK, Kerberos, MAC, and none. eap Configures Extensible Authentication Protocol (EAP) authentication (802.1X) eap-mac Configures EAP or MAC authentication depending on client eap-psk Configures EAP authentication or pre-shared keys depending on client (This setting is only valid with Temporal Key Integrity Protocol (TKIP) or Counter Mode with Cipher Block Chaining Message Authentication Code Protocol (CCMP)) kerberos Configures Kerberos authentication (encryption will change to WEP128 if its not already WEP128 or Keyguard) mac Configures MAC authentication (RADIUS lookup of MAC address) none No authentication is used or the client uses pre-shared keys
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 340 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax bridging-mode [local|tunnel] Parameters bridging-mode [local|tunnel] Example wm3700-37FABE(config-wlan-wlan1)#bridging-mode local wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 acl exceed-rate wireless-client-denied-traffic 20 disassociate wm3700-37FABE(config-wlan-wlan1)# broadcast-dhcp wlan-mode commands Configures the broadcast DHCP packet handling parameters bridging-mode Configures how packets are bridged to and from a WLAN. The options available are local and tunnel. local Bridges packets between WLAN and local ethernet ports tunnel Tunnels packets to other devices (typically a wireless controller)
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 341 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax broadcast-dhcp validate-offer Parameters broadcast-dhcp validate-offer Example wm3700-37FABE(config-wlan-wlan1)#broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# broadcast-ssid wlan-mode commands Advertises the WLAN SSID in beacons validate-offer Validates the broadcast DHCP packet destination (a wireless client associated to the radio) before forwarding over the air
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 342 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax broadcast-ssid Parameters None Example wm3700-37FABE(config-wlan-wlan1)#broadcast-ssid wm3700-37FABE(config-wlan-wlan1)# captive-portal-enforcement wlan-mode commands Configures the WLANs captive portal enforcement Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax captive-portal-enforcement {fall-back}
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 343 Parameters captive-portal-enforcement {fall-back} Example wm3700-37FABE(config-wlan-wlan1)#captive-portal-enforcement fall-back wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# client-access wlan-mode commands Enables WLAN client access (for normal data operations) Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax client-access captive-portal-enforcement Enables captive portal enforcement on a WLAN fall-back Optional. Enforces captive portal validation if WLAN authentication fails (applicable to EAP or MAC authentication only)
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 344 Parameters None Example wm3700-37FABE(config-wlan-wlan1)#client-access wm3700-37FABE(config-wlan-wlan1)# client-client-communication wlan-mode commands Allows frame switching from one client to another on a WLAN Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax client-client-communication Parameters None Example wm3700-37FABE(config-wlan-wlan1)#client-client-communication wm3700-37FABE(config-wlan-wlan1)#s client-load-balancing wlan-mode commands Configures client load balancing on a WLAN
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 345 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax client-load-balancing {allow-single-band-clients|band-discovery-intvl| capability-ageout-time|max-probe-req|probe-req-invl} client-load-balancing {allow-single-band-clients [2.4Ghz|5Ghz]| band-discovery-intvl [<0-10000>]|capability-ageout-time [<0-10000>]} client-load-balancing {{max-probe-req|probe-req-intvl} [2.4Ghz|5Ghz] [<0- 10000>]} Parameters client-load-balancing {allow-single-band-clients [2.4Ghz|5Ghz]| band-discovery-intvl [<0-10000>]|capability-ageout-time [<0-10000>]} client-load-balancing {{max-probe-req|probe-req-intvl} [2.4Ghz|5Ghz] [<0-10000>]} client-load-balancing Configures client load balancing on a WLAN allow-single-band-clients [2.4GHz|5GHz] Optional. Allows single band clients to associate even during load balancing 2.4GHz Enables load balancing across 2.4GHz channels 5GHz Enables load balancing across 5GHz channels band-discovery-intvl <0-10000> Optional. Configures time interval to discover a client's band capability before associating it <0-10000> Specify a value from 0 - 10000 seconds. capability-ageout-time <0-10000> Optional. Configures a client's capability ageout interval <0-10000> Specify a value from 0 - 10000 seconds. client-load-balancing Configures load balancing of clients on a WLAN max-probe-req [2.4GHz|5GHz] <0-10000> Optional. Configures client probe request interval limits for association 2.4GHz Configures maximum client probe requests on 2.4GHz radios 5GHz Configures maximum client probe requests on 5GHz radios <0-10000> Specify a client probe request threshold from 0 - 100000.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 346 Example wm3700-37FABE(config-wlan-wlan1)#client-load-balancing allow-single-band- clients 2.4ghz wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#client-load-balancing band-discovery-intvl 2 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABEconfig-wlan-wlan1)#client-load-balancing probe-req-intvl 5ghz 5 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# data-rates wlan-mode commands Specifies the 802.11 rates supported on a WLAN probe-req-intvl 2.4GHz|5GHz] <0-10000> Optional. Configures client probe request interval limits for association 2.4GHz Configures client probe request interval on 2.4GHz radios 5GHz Configures client probe request interval on 5GHz radios <0-10000> Specify a value from 0 - 100000.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 347 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax data-rates [2.4GHz|5GHz] data-rates 2.4GHz [b-only|bg|bgn|custom|default|g-only|gn] data-rates 2.4GHz [b-only|bg|bgn|default|g-only|gn] data-rates 2.4GHz custom [1|11|12|18|2|24|36|48|5.5|54|6|9| basic-1|basic-11|basic-12|basic-18|basci-2|basic-24|basic-36| basic-48|basic-5.5|basic-54|basic-6|basic-9|basic-mcs0-7|mcs0-15| mcs0-7|mcs8-15] data-rates 5GHz [a-only|an|custom|default] data-rates 5GHz [a-only|an|default] data-rates 5GHz custom [12|18|24|36|48|54|6|9|basic-1|basi-11| basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic- 5.5|basic-54| basic-6|basic-9|basic-mcs0-7|mcs0-15|mcs0-7|mcs8-15] Parameters data-rates 2.4GHz [b-only|bg|bgn|default|g-only|gn] data-rates 5GHz [a-only|an|default] data-rates Specifies the 802.11 rates supported when mapped to a 2.4GHz radio b-only Uses rates that support only 11b clients bg Uses rates that support both 11b and 11g clients bgn Uses rates that support 11b, 11g and 11n clients default Uses the default rates configured for a 2.4GHz radio g-only Uses rates that support operation in the 11g only mode gn Uses rates that support 11g and 11n clients data-rates Specifies the 802.11 rates supported when mapped to a 5GHz radio
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 348 data-rates [2.4GHz|5GHz] custom [1|11|12|18|2|24|36|48|5.5|54|6|9| basic-1|basic-11|basic-12|basic-18|basic-2|basic-24|basic-36| basic-48|basic-5.5|basic-54|basic-6|basic-9|basic-mcs0-7|mcs0-15| mcs0-7|mcs8-15] a-only Uses rates that support operation in 11a only an Uses rates that support 11a and 11n clients default Uses default rates configured for a 5GHz data-rates [2.4GHz|5GHz] Specifies the 802.11 rates supported when mapped to a 2.4GHz or 5GHz radio custom Configures a data rates list by specifying each rate individually. Use 'basic-' prefix before a rate to indicate it is used as a basic rate (For example, 'data-rates custom basic-1 basic-2 5.5 11'). The data-rates for 2.4GHz and 5GHz channels are the same with a few exceptions. The 2.4GHz channel has a few extra data rates: 1, 11, 2, and 5.5. 1,11,2,5.5 The following data rates are specific to the 2.4GHz channel: 1 1-Mbps 11 11-Mbps 2 2-Mbps 5.5 5.5-Mbps 12,18,24,36,48,54,6,9, basic-1,basic-11, basic-12,basic-18,basic-2, basic-36,basic-48,basic- 5.5, basic-54,basic-6,basic-9, basic-mcs0-7,mcs0-15, mcs0-7,mcs8-15 The following data rates are common to both the 2.4Ghz and 5GHz channels: 12 12 Mbps 18 18-Mbps 24 24 Mbps 36 36-Mbps 48 48-Mbps 54 54-Mbps 6 6-Mbps 9 9-Mbps basic-1 basic 1-Mbps basic-11 basic 11-Mbps basic-12 basic 12-Mbps basic-18 basic 18-Mbps basic-2 basic 2-Mbps basic-36 basic 36-Mbps basic-48 basic 48-Mbps basic-5.5 basic 5.5-Mbps basic-54 basic 54-Mbps basic-6 basic 6-Mbps basic-9 basic 9-Mbps basic-mcs0-7 Modulation and coding scheme 0-7 as a basic rate mcs0-15 Modulation and coding scheme 0-15 mcs0-7 Modulation and coding scheme 0-7 mcs8-15 Modulation and coding scheme 8-15
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 349 Example wm3700-37FABE(config-wlan-wlan1)#data-rates 2.4GHz gn wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# description wlan-mode commands Defines the WLAN description Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax description <LINE> Parameters description <LINE> <LINE> Specify a WLAN description
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 350 Example wm3700-37FABE(config-wlan-wlan1)#description testwlan wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type none authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# encryption-type wlan-mode commands Sets a WLANs encryption type Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax encryption-type [ccmp|keyguard|none|tkip|tkip-ccmp|wep128| web128-keyguard|wep64] Parameters encryption-type [ccmp|keyguard|none|tkip|tkip-ccmp|wep128| web128-keyguard|wep64] encryption-type Configures the WLANs data encryption parameters
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 351 Example wm3700-37FABEconfig-wlan-wlan1)#encryption-type tkip-ccmp wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# enforce-dhcp wlan-mode commands Drops packets from clients with a static IP address ccmp Configures Advanced Encryption Standard (AES) Counter Mode CBC-MAC Protocol (AES-CCM/CCMP) keyguard Configures Keyguard-MCM (Mobile Computing Mode) tkip Configures TKIP tkip-ccmp Configures the TKIP and AES-CCM/CCMP encryption modes wep128 Configures WEP with 128 bit keys wep128-keyguard Configures WEP128 as well as Keyguard-MCM encryption modes wep64 Configures WEP with 64 bit keys. A WEP64 configuration is insecure when two WLANs are mapped to the same VLAN, and one uses no encryption while the other uses WEP.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 352 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax enforce-dhcp Parameters None Example wm3700-37FABE(config-wlan-wlan1)#enforce-dhcp wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back acl exceed-rate wireless-client-denied-traffic 20 disassociate enforce-dhcp broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# ip wlan-mode commands Configures Internet Protocol (IP) settings
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 353 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [arp|dhcp] ip arp [header-mismatch-validation|trust] ip dhcp trust Parameters ip arp [header-mismatch-validation|trust] ip dhcp trust Example wm3700-37FABE(config-wlan-wlan1)#ip dhcp trust wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn ip arp Configures the IP settings for ARP packets header-mismatch- validation Verifies mismatch of source MAC address in the ARP and Ethernet headers trust Sets ARP responses as trusted for a WLAN/range ip dhcp Configures the IP settings for DHCP packets trust Sets DHCP responses as trusted for a WLAN/range
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 354 client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate enforce-dhcp broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# kerberos wlan-mode commands Configures Kerberos authentication parameters on a WLAN Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax kerberos [password|realm|server] kerberos password [0 <LINE>|2 <LINE>|<LINE>] kerberos realm <REALM> kerberos server [primary|secondary|timeout] kerberos server [primary|secondary] host <IP/HOSTNAME> {port [<1-65535>]} keberos server timeout <1-60> Parameters kerberos password [0 <LINE>|2 <LINE>|<LINE>] kerberos Configures a WLANs Kerberos authentication parameters The parameters are: password, realm, and server.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 355 kerberos realm <REALM> kerberos server [primary|secondary] host <IP/HOSTNAME> {port [<1-65535>]} keberos server timeout <1-60> Example wm3700-37FABE(config-wlan-wlan1)#kerberos server timeout 12 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#kerberos server primary host 172.16.10.9 port 88 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local password Configures a Kerberos Key Distribution Center (KDC) server password. The password should not exceed 127 characters. The password options are: 0 <LINE> Configures a clear text password 2 <LINE> Configures an encrypted password <LINE> Specify the password. kerberos Configures a WLANs Kerberos authentication parameters The parameters are: password, realm, and server. realm <REALM> Configures a Kerberos KDC server realm. The REALM should not exceed 127 characters. kerberos Configures a WLANs Kerberos authentication parameters The parameters are: password, realm, and server. server [primary|secondary] Configures the primary and secondary KDC server parameters primary Configures the primary KDC server parameters secondary Configures the secondary KDC server parameters host <IP/HOSTNAME> Sets the primary or secondary KDC server address <IP/HOSTNAME> Specify the IP address or name of the KDC server. port <1-65535> Optional. Configures the UDP port used to connect to the KDC server <1-65535> Specify the port from 1 - 65535. The default is 88. kerberos Configures a WLANs Kerberos authentication parameters The parameters are: password, realm, and server. timeout <1-60> Modifies the Kerberos KDC servers timeout parameters <1-60> Specifies the time the wireless controller waits for a response from the Kerberos KDC server before retrying. Specify a value from 1 - 60 seconds.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 356 encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 kerberos server timeout 12 kerberos server primary host 172.16.10.9 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate enforce-dhcp broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# motorola-extensions wlan-mode commands Enables support for Extreme Networks specific extensions to 802.11 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax motorola-extensions [move-command|smart-scan|symbol-load-information| wmm-load-information] Parameters motorola-extensions [move-command|smart-scan|symbol-load-information| wmm-load-information] move-command Enables support for move (fast roaming) feature smart-scan Enables support for smart scanning feature symbol-load-information Enables support for the Symbol Technologies load information element (Element ID 173) wmm-load-information Enables support for the Extreme Networks WMM load information element
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 357 Example wm3700-37FABE(config-wlan-wlan1)#motorola-extensions wmm-load-information wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 kerberos server timeout 12 kerberos server primary host 172.16.10.9 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate enforce-dhcp broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# no wlan-mode commands Negates WLAN mode commands and reverts values to their default Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no <parameter>
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 358 Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3700-37FABE(config-wlan-wlan1)#no ? 802.11w Disable support for Protected Management Frames (IEEE 802.11w) accounting Configure how accounting records are created for this wlan acl Actions taken based on ACL configuration [ packet drop being one of them] answer-broadcast-probes Do not Include this wlan when responding to probe requests that do not specify an SSID authentication-type Reset the authentication to use on this wlan to default (none/Pre-shared keys) broadcast-dhcp Configure broadcast DHCP packet handling broadcast-ssid Do not advertise the SSID of the WLAN in beacons captive-portal-enforcement Configure how captive-portal is enforced on the wlan client-access Disallow client access on this wlan (no data operations) client-client-communication Disallow switching of frames from one wireless client to another on this wlan client-load-balancing Disable load-balancing of clients on this wlan data-rates Reset data rate configuration to default description Reset the description of the wlan encryption-type Reset the encryption to use on this wlan to default (none) enforce-dhcp Drop packets from Wireless Clients with static IP address ip Internet Protocol (IP) kerberos Configure kerberos authentication parameters motorola-extensions Disable support for Motorola-Specific extensions to 802.11 proxy-arp-mode Configure handling of ARP requests with proxy-arp is enabled radius Configure RADIUS related parameters shutdown Enable the use of this wlan
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 359 ssid Configure ssid use Set setting to use vlan Map the default vlan (vlan-id 1) to the wlan vlan-pool-member Delete a mapped vlan from this wlan wep128 Reset WEP128 parameters wep64 Reset WEP64 parameters wireless-client Configure wireless-client specific parameters wpa-wpa2 Modify tkip-ccmp (wpa/wpa2) related parameters service Service Commands wm3700-37FABE(config-wlan-wlan1)# The wlan1 settings before the execution of the no command: wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 description testwlan ssid wlan1 bridging-mode local encryption-type tkip-ccmp authentication-type eap 802.11w sa-query timeout 110 802.11w sa-query attempts 1 kerberos server timeout 12 kerberos server primary host 172.16.10.9 accounting syslog host 172.16.10.12 port 2 data-rates 2.4GHz gn motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate enforce-dhcp broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no accounting syslog wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no description wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no authentication-type wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no encryption-type wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no enforce-dhcp
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 360 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no kerberos server primary host wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no kerberos server timeout wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#no data-rates 2.4GHz wm3700-37FABE(config-wlan-wlan1)# The wlan1 settings after the execution of the no command: wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# proxy-arp-mode wlan-mode commands Enables proxy ARP mode for handling ARP requests Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax proxy-arp-mode [dynamic|strict]
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 361 Parameters proxy-arp-mode [dynamic|strict] Example wm3700-37FABE(config-wlan-wlan1)#proxy-arp-mode strict wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 captive-portal-enforcement fall-back ip dhcp trust acl exceed-rate wireless-client-denied-traffic 20 disassociate proxy-arp-mode strict broadcast-dhcp validate-offer wm3700-37FABE(config-wlan-wlan1)# radius wlan-mode commands Configures RADIUS related parameters proxy-arp-mode Enables proxy ARP mode for handling ARP requests. The options available are dynamic and strict. dynamic Forwards ARP requests to the wireless side (for which a response could not be proxied) strict Does not forward ARP requests to the wireless side
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 362 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radius [dynamic-authorization|nas-identifier|nas-port-id|vlan-assignment] radius [dynamic-authorization|nas-identifier <NAS-ID>| nas-port-id <NAS-PORT-ID>|vlan-assignment] Parameters radius [dynamic-authorization|nas-identifier <NAS-ID>| nas-port-id <NAS-PORT-ID>|vlan-assignment] Example wm3700-37FABE(config-wlan-wlan1)#radius vlan-assignment wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 radius vlan-assignment motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 proxy-arp-mode strict dynamic-authorization Enables support for disconnect and change of authorization messages (RFC5176) nas-identifier <NAS-ID> Configures the WLAN NAS identifier sent to the RADIUS server. The NAS identifier should not exceed 256 characters. nas-port-id <NAS-PORT-ID> Configures the WLAN NAS port ID sent to the RADIUS server. The NAS port identifier should not exceed 256 characters. vlan-assignment Configures the VLAN assignment of a WLAN
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 363 wm3700-37FABE(config-wlan-wlan1)# shutdown wlan-mode commands Shuts down a WLAN Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax shutdown Parameters None Example wm3700-37FABE(config-wlan-1)#shutdown ssid wlan-mode commands Configures a WLANs SSID
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 364 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ssid <SSID> Parameters ssid <SSID> Example wm3700-37FABE(config-wlan-wlan1)#ssid test1 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid test1 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 radius vlan-assignment motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 proxy-arp-mode strict wm3700-37FABE(config-wlan-wlan1)# use wlan-mode commands This command associates an existing captive portal with a WLAN. <SSID> Specify the WLANs SSID. The WLAN SSID is case sensitive and alphanumeric. Its length should not exceed 32 characters.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 365 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [aaa-policy|association-acl-policy|captive-portal|ip-access-list| mac-access-list|wlan-qos-policy] use [aaa-policy <AAA-POLICY-NAME>|association-acl-policy <ASSOCIATION- POLICY- NAME>|captive-portal <CAPTIVE-PORTAL-NAME>|wlan-qos-policy <WLAN- QOS-POLICY- NAME>] use ip-access-list [in|out] <IP-ACCESS-LIST-NAME> use mac-access-list [in|out] <MAC-ACCESS-LIST-NAME> Parameters use [aaa-policy <AAA-POLICY-NAME>|association-acl-policy <ASSOCIATION- POLICY- NAME>|captive-portal <CAPTIVE-PORTAL-NAME>|wlan-qos-policy <WLAN-QOS- POLICY-NAME>] aaa-policy <AAA-POLICY-NAME> Uses a specified AAA policy with a WLAN <AAA-POLICY-NAME> Specify the name of the AAA policy. association-acl <ASSOCIATION-POLICY- NAME> Uses a specified association ACL policy with a WLAN <ASSOCIATION-POLICY-NAME> Specify the name of the association ACL policy. captive-portal <CAPTIVE-PORTAL-NAME> Enables a WLANs captive portal authentication <CAPTIVE-PORTAL-NAME> Specify the name of the captive portal. wlan-qos-policy <WLAN-QOS-POLICY- NAME> Uses a specified WLAN QoS policy with a WLAN <wlan-qos-policy-name> Specify the name of the WLAN QoS policy.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 366 use ip-access-list [in|out] <IP-ACCESS-LIST-NAME>] use mac-access-list [in|out] <MAC-ACCESS-LIST-NAME> Example wm3700-37FABE(config-wlan-wlan1)#use ip-access-list in extreme wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid test1 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 radius vlan-assignment motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 use ip-access-list in extreme proxy-arp-mode strict wm3700-37FABE(config-wlan-wlan1)# vlan wlan-mode commands Sets the VLAN where traffic from a WLAN is mapped ip-access-list [in|out] <IP- ACCESS-LIST-NAME> Specifies the IP access list for incoming and outgoing packets in Incoming packets out Outgoing packets <IP-ACCESS-LIST-NAME> Specify the name of the IP access list. mac-access-list [in|out] <MAC-ACCESS-LIST- NAME> Specifies the MAC access list for incoming and outgoing packets. in Incoming packets out Outgoing packets <MAC-ACCESS-LIST-NAME> Specify the name of the MAC access list.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 367 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax vlan <1-4094> Parameters vlan <1-4094> Example wm3700-37FABE(config-wlan-wlan1)#vlan 4 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid test1 vlan 4 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 radius vlan-assignment motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 use ip-access-list in extreme proxy-arp-mode strict wm3700-37FABE(config-wlan-wlan1)# vlan-pool-member wlan-mode commands Adds a member VLAN to a WLANs VLAN pool <1-4094> Sets a WLANs VLAN ID. This command starts a new VLAN assignment for a WLAN index. All prior VLAN settings are erased.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 368 NOTE Configuration of a VLAN pool overrides the 'vlan' configuration. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax vlan-pool-member <WORD> {limit [<0-8192>]} Parameters vlan-pool-member <WORD> {limit [<0-8192>]} Example wm3700-37FABE(config-wlan-wlan1)#vlan-pool-member 1-10 limit 1 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid test1 vlan-pool-member 1 limit 1 vlan-pool-member 2 limit 1 vlan-pool-member 3 limit 1 vlan-pool-member 4 limit 1 vlan-pool-member 5 limit 1 vlan-pool-member 6 limit 1 vlan-pool-member 7 limit 1 vlan-pool-member 8 limit 1 vlan-pool-member 9 limit 1 vlan-pool-member 10 limit 1 vlan-pool-member Adds a member VLAN to a WLANs VLAN pool <WORD> Defines the VLAN configuration. It is either a single index, or a list of VLAN IDs (For example, 1,3,7) limit <0-8192> Optional. Is ignored if the number of clients are limited and well within the limits of the DHCP pool on the VLAN <0-8192> Specifies the number of users allowed
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 369 bridging-mode local encryption-type none authentication-type none 802.11w sa-query timeout 110 802.11w sa-query attempts 1 radius vlan-assignment motorola-extensions wmm-load-information client-load-balancing probe-req-intvl 5ghz 5 client-load-balancing band-discovery-intvl 2 use ip-access-list in extreme proxy-arp-mode strict wm3700-37FABE(config-wlan-wlan1)# wep128 wlan-mode commands Configures WEP128 parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wep128 [key|keys-from-passkey|transmit-key] wep128 key <1-4> [ascii|hex] [0 <WORD>|2 <WORD>|<WORD>] wep128 keys-from-passkey <WORD> wep128 transmit-key <1-4> Parameters wep128 key <1-4> [ascii|hex] [0 <WORD>|2 <WORD>|<WORD>] wep128 Configures WEP128 parameters. The parameters are: key, key-from-passkey, and transmit-key. key <1-4>] Configures pre-shared hex keys <1-4> Configures a maximum of four key indexes. Select the key index from 1 - 4.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 370 wep128 keys-from-passkey <WORD>] wep128 transmit-key <1-4>] Example wm3700-37FABE(config-wlan-wlan1)#wep128 transmit-key 1 wm3700-37FABE(config-wlan-wlan1)# wep64 wlan-mode commands Configures WEP64 parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wep64 [key|keys-from-passkey|transmit-key] ascii [0 <WORD>| 2 <WORD>|<WORD>] Sets keys as ASCII characters (5 characters for WEP64, 13 for WEP128) 0 <WORD> Configures a clear text key 2 <WORD> Configures an encrypted key <WORD> Configures keys as 13 ASCII characters converted to hex, or 26 hexadecimal characters hex [0 <WORD>| 2 <WORD>|<WORD>] Sets keys as hexadecimal characters (10 characters for WEP64, 26 for WEP128). 0 <WORD> Configures a clear text key 2 <WORD> Configures an encrypted key <WORD> Configures keys as 13 ASCII characters converted to hex, or 26 hexadecimal characters keys-from-passkey <WORD> Specifies a passphrase from which keys are derived <WORD> Specify a passphrase from 4 - 32 characters. transmit-key <1-4> Configures the key index used for transmission from an AP to a wireless client <1-4> Specify a key index from 1 - 4.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 371 wep64 key <1-4> [ascii|hex] [0 <WORD>|2 <WORD>|<WORD>] wep64 keys-from-passkey <WORD> wep64 transmit-key <1-4>] Parameters wep64 key <1-4> [ascii|hex] [0 <WORD>|2 <WORD>|<WORD>] wep64 keys-from-passkey <WORD>] wep64 transmit-key <1-4>] Example wm3700-37FABE(config-wlan-wlan1)#wep64 key 1 ascii symbo wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#wep64 transmit-key 1 wm3700-37FABE(config-wlan-wlan1)# wireless-client wlan-mode commands Configures the transmit power indicated to clients wep64 Configures WEP64 parameters The parameters are: key, key-from-passkey, and transmit-key. key <1-4>] Configures pre-shared hex keys <1-4> Configures a maximum of four key indexes. Select a key index from 1 - 4. ascii [0 <WORD>| 2 <WORD>|<WORD>] Sets keys as ASCII characters (5 characters for WEP64, 13 for WEP128) 0 <WORD> Configures a clear text key 2 <WORD> Configures an encrypted key <WORD> Configures key (10 hex or 5 ASCII characters for WEP64, 26 hex or 13 ASCII characters for WEP128). hex [0 <WORD>| 2 <WORD>|<WORD>] Sets keys as hexadecimal characters (10 characters for WEP64, 26 for WEP128). 0 <WORD> Configures a clear text key 2 <WORD> Configures an encrypted key <WORD> Configures the key (10 hex or 5 ASCII characters for WEP64, 26 hex or 13 ASCII characters for WEP128) keys-from-passkey <WORD> Specifies a passphrase from which keys are derived <WORD> Specify a passphrase from 4 - 32 characters. transmit-key <1-4> Configures the key index used for transmission from an AP to a wireless client <1-4> Specify a key index from 1 - 4.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 372 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wireless-client [cred-cache-ageout|hold-time |inactivity-timeout| max-firewall-sessions|reauthentication|tx-power|vlan-cache-out] wireless-client [cred-cache-ageout <60-86400>|hold-time <1-300>| inactivity-timeout <60-86400>|max-firewall-sessions <10-10000>| reauthentication <30-86400>|tx-power <0-20>|vlan-cache-out <60- 86400>] Parameters wireless-client [cred-cache-ageout <60-86400>|hold-time <1-300>| inactivity-timeout <60-86400>|max-firewall-sessions <10-10000>| reauthentication <30-86400>|tx-power <0-20>|vlan-cache-out <60-86400>] wireless-client Configures the transmit power indicated to wireless clients for transmission cred-cache-ageout <60-86400> Configures the timeout period for which client credentials (For example, encryption keys) are cached across associations <60-86400> Specify a value from 60 - 86400 seconds. hold-time <1-300> Configures the time period for which wireless client state information is cached post roaming <1-300> Specify a value from 1 - 300 seconds. inactivity-timeout <60-86400> Configures an inactivity timeout period in seconds. If a frame is not received from a wireless client for this period of time, the client is disassociated. <60-86400> Specify a value from 60 - 86400 seconds. max-firewall-sessions <10-10000> Configures the maximum firewall sessions allowed per client on a WLAN <10-10000> Specify the maximum number of firewall sessions allowed from 10 - 10000. reauthentication <30-86400> Configures periodic reauthentication of associated clients <30-86400> Specify the client reauthentication interval from 30 - 86400 seconds. tx-power <0-20> Configures the transmit power indicated to clients <0-20> Specify a value from 0 - 20 dBm.
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 373 Example wm3700-37FABE(config-wlan-wlan1)#wireless-client cred-cache-ageout 65 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#wireless-client hold-time 10 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#wireless-client max-firewall-sessions 100 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#wireless-client reauthentication 35 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#wireless-client tx-power 12 wm3700-37FABE(config-wlan-wlan1)# wm3700-37FABE(config-wlan-wlan1)#show context wlan wlan1 ssid wlan1 bridging-mode tunnel encryption-type none authentication-type none wireless-client hold-time 10 wireless-client cred-cache-ageout 65 wireless-client max-firewall-sessions 100 wireless-client reauthentication 35 wep64 key 1 hex 0 73796d626f wireless-client tx-power 12 wm3700-37FABE(config-wlan-wlan1)# wpa-wpa2 wlan-mode commands Modifies TKIP-CCMP (WPA/WPA2) related parameters vlan-cache-ageout <60-86400> Configures the timeout period for which client VLAN information is cached across associations. <60-86400> Specify a value from 60 - 86400 seconds.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 374 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wpa-wpa2 [exclude-wpa2-tkip|handshake|key-rotation|opp-pmk-caching| pmk-caching|preauthentication|psk|tkip-countermeasures|use-sha256- akm] wpa-wpa2 [exclude-wpa2-tkip|opp-pmk-caching|pmk-caching|preauthentication| use-sha256-akm] wpa-wpa2 handshake [attempts|init-wait|priority|timeout] wpa-wpa2 handshake [attempts <1-5>|init-wait <5-1000000>|priority [high|normal]| timeout <10-5000>] wpa-wpa2 key-rotation [broadcast|unicast] <30-86400>] wpa-wpa2 psk [0 <LINE>|2 <LINE>|<LINE>] wpa-wpa2 tkip-countermeasures holdtime <0-65535> Parameters wpa-wpa2 [exclude-wpa2-tkip|opp-pmk-caching|pmk-caching|preauthentication| use-sha256-akm] wpa-wpa2 Modifies TKIP-CCMP (WPA/WPA2) related parameters exclude-wpa2-tkip Excludes the Wi-Fi Protected Access II (WPA2) version of TKIP. It supports the WPA version of TKIP only. opp-pmk-caching Uses opportunistic key caching (same Pairwise Master Key (PMK) across APs for fast roaming with EAP.802.1x). pmk-caching Uses cached pair-wise master keys (fast roaming with eap/802.1x) preauthentication Uses pre-authentication mode (WPA2 fast roaming) use-sha256-akm Uses sha256 authentication key management suite
Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 375 wpa-wpa2 handshake [attempts <1-5>|init-wait <5-1000000>| priority [high|normal]|timeout <10-5000>] wpa-wpa2 key-rotation [broadcast|unicast] <30-86400> wpa-wpa2 psk [0 <LINE>|2 <LINE>|<LINE>] wpa-wpa2 tkip-countermeasures holdtime <0-65535>] wpa-wpa2 Modifies TKIP-CCMP (WPA/WPA2) related parameters handshake Configures WPA/WPA2 handshake parameters attempts <1-5> Configures the total number of times a message is transmitted towards a non- responsive client <1-5> Specify a value from 1 - 5. init-wait <5-1000000> Configures a minimum wait-time period before the first handshake message is transmitted from the AP <5-1000000> Specify a value from 5 - 1000000 microseconds. priority [high|normal] Configures the relative priority of handshake messages compared to other data traffic high Treats handshake messages as high priority packets on a radio normal Treats handshake messages as normal priority packets on a radio timeout <10-5000> Configures the timeout period for a handshake message to retire. Once this timeout period is over, the handshake message is retired. <10-5000> Specify a value from 10 - 5000 milliseconds. wpa-wpa2 Modifies TKIP-CCMP (WPA/WPA2) related parameters key-rotation Configures parameters related to periodic rotation of encryption keys. The parameters are periodic rotation of keys for broadcast, multicast, and unicast traffic. broadcast <30-86400> Configures the periodic rotation of keys used for broadcast and multicast traffic. This parameter specifies the interval at which keys are rotated <30-86400> Specify a value from 30 - 86400 seconds. unicast <30-86400> Configures a periodic interval for the rotation of keys, used for unicast traffic <30-86400> Specify a value from 30 - 86400 seconds. wpa-wpa2 Modifies TKIP-CCMP (WPA/WPA2) related parameters psk Configures a pre-shared key. The key options are: 0, 2, and LINE 0 <LINE> Configures a clear text key 2 <LINE> Configures an encrypted key <LINE> Enter the pre-shared key either as a passphrase not exceeding 8 - 63 characters, or as a 64 character (256bit) hexadecimal value wpa-wpa2 Modifies TKIP-CCMP (WPA/WPA2) parameters tkip-countermeasures Configures a hold time period for implementation of TKIP counter measures holdtime <0-65535> Configures the amount of time a WLAN is disabled when TKIP counter measures are invoked <0-65535> Specify a value from 0 - 65536 seconds.
TM 4000 Series Access Point CLI Reference Guide 377 wlan-qos-policy Global Configuration Commands Configures a WLAN QoS policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wlan-qos-policy <WLAN-QOS-POLICY-NAME> Parameters wlan-qos-policy <WLAN-QOS-POLICY-NAME> Example wm3700-37FABE(config)#wlan-qos-policy test wm3700-37FABE(config-wlan-qos-test)# NOTE For more information on WLAN QoS policy commands, see Chapter 23, WLAN QoS Policy. <WLAN-QOS-POLICY- NAME> Specify the WLAN QoS policy name. If the policy does not exist, it is created.
Chapter 5: Global Configuration Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 378
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 379 C H A P T E R 6 Common Commands This chapter describes the CLI commands used in the USER EXEC, PRIV EXEC, and GLOBAL CONFIG modes. The PRIV EXEC command set contains commands available within the USER EXEC mode. Some commands can be entered in either mode. Commands entered in either the USER EXEC or PRIV EXEC mode are referred to as EXEC mode commands. If a user or privilege is not specified, the referenced command can be entered in either mode. Common Commands The following table summarizes common commands clrscr Common Commands Clears the screen and refreshes the prompt, irrespective of the mode you are in Command Description Reference clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 no Negates a command or reverts values to their default settings page 6-388 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations. page 6-391 show Displays running system information page 6-418 write Writes the systems running configuration to memory or terminal page 6-420
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 380 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax clrscr Parameters None Example The terminal window or screen before the clrscr command is executed: wm3400-34710C8#ap-upgrade ? DEVICE-NAME Name/MAC address of AP all Upgrade all access points AP4021 Upgrade an AP4021 device AP4600 Upgrade an AP4600 device AP4511 Upgrade an AP4511 device AP4521 Upgrade an AP4521 device AP4532 Upgrade an AP4532 device AP4700 Upgrade an AP4700 device cancel-upgrade Cancel upgrading the AP load-image Load the AP images to controller for ap-upgrades rf-domain Upgrade all access points belonging to an RF Domain wm3400-34710C8#clrscr The terminal window or screen after the clrscr command is executed: wm3400-34710C8# commit Common Commands Commits all changes made in the active session. Use the commit command to save and invoke settings entered during the current transaction.
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 381 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax commit {write}{memory} Parameters commit {write}{memory} Example wm3400-34710C8#commit write memory [OK] wm3400-34710C8# end Common Commands Ends and exits the current mode and moves to the PRIV EXEC mode. The prompt changes to wm3400- 34710C8#. write Optional. If a commit succeeds, the configuration is written to memory memory Optional. Writes to memory
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 382 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax end Parameters None Example wm3400-34710C8(config)#end wm3400-34710C8# exit Common Commands The exit command works differently in its three supported modes. In the Global Config mode, it ends the current mode and moves to the previous mode, which is the Priv Exec mode. The prompt changes from (config)# to #. When used in the Priv Exec and User Exec modes, the exit command ends the current session and connection to the terminal device.
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 383 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax exit Parameters None Example wm3400-34710C8(config)#exit wm3400-34710C8# help Common Commands Describes the interactive help system Use this command to access the advanced help feature. Use ? anytime at the command prompt to access the help topic Two kinds of help are provided: Full help is available when ready to enter a command argument Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (for example 'show ve?').
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 384 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax help {search|show} help {show [configuration-tree]} help {search [<WORD>] {detailed|only-show|skip-no|skip-show}} NOTE The show configuration-tree option is not available in the Global Config mode. Parameters help {show [configuration-tree]} help {search [<WORD>] {detailed|only-show|skip-no|skip-show}} Example wm3400-34710C8>help search crypto detailed show configuration-tree Optional. Displays the running system information configuration-tree Displays relationship amongst configuration objects search <WORD> Optional. Searches for CLI commands related to a specific target term <WORD> Specify a target term (for example, a feature, or configuration parameter). After specifying the term, select one of the following options: detailed, only-show, skip-no, or skip-show. The system displays information based on the option selected. detailed Optional. Searches and displays help strings in addition to mode and commands only-show Optional. Displays only show commands. Does not display configuration commands skip-no Optional. Displays only configuration commands. Does not display no commands skip-show Optional. Displays only configuration commands. Does not display show commands
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 385 Found 29 references for crypto Found 113 references for crypto Mode : User Exec Command : show crypto key rsa (|public-key-detail) (|(on DEVICE-NAME)) \ Show running system information \ Encryption related commands \ Key management operations \ Show RSA public Keys \ Show the public key in PEM format \ On AP/Controller \ AP / Controller name : show crypto pki trustpoints (WORD|all|)(|(on DEVICE-NAME)) \ Show running system information \ Encryption related commands \ Public Key Infrastructure related commands \ Display the configured trustpoints \ Display a particular trustpoint's details \ Display details for all trustpoints \ On AP/Controller \ AP / Controller name : show crypto isakmp sa (|(on DEVICE-NAME)) \ Show running system information \ Encryption Module \ Show ISAKMP related statistics \ Show all ISAKMP Security Associations \ On AP/Controller \ AP / Controller name : show crypto ipsec sa (|(on DEVICE-NAME)) \ Show running system information \ Encryption Module \ Show IPSec related statistics \ IPSec security association \ On AP/Controller \ AP / Controller name : crypto key generate rsa WORD <1024-2048> (|(on DEVICE-NAME)) \ Encryption related commands \ Key management operations \ Generate a keypair \ Generate a RSA keypair \ Keypair name ........................................................................... .........................................................................wm 3400-34710C8> wm3400-34710C8>help show configuration-tree ## ACCESS-POINT / SWITCH ## ---+ | +--> [[ RF-DOMAIN ]]
TM 4000 Series Access Point CLI Reference Guide 387 Found 32 references for "service" Mode : User Exec Command : service show cli : service show rim config (|include-factory) : service show wireless credential-cache : service show wireless neighbors : service show general stats(|(on DEVICE-OR-DOMAIN-NAME)) : service show process(|(on DEVICE-OR-DOMAIN-NAME)) : service show mem(|(on DEVICE-OR-DOMAIN-NAME)) : service show top(|(on DEVICE-OR-DOMAIN-NAME)) : service show crash-info (|(on DEVICE-OR-DOMAIN-NAME)) : service cli-tables-skin (none|minimal|thin|thick|stars|hashes|percent|ansi|utf-8) (grid|) : service cli-tables-expand (|left|right) : service wireless clear unauthorized aps (|(on DEVICE-OR-DOMAIN- NAME)) : service wireless qos delete-tspec AA-BB-CC-DD-EE-FF tid <0-7> : service wireless wips clear-event-history : service wireless wips clear-mu-blacklist (all|(mac AA-BB-CC-DD- EE-FF)) : service radio <1-3> dfs simulate-radar (primary|extension) : service smart-rf run-calibration : service smart-rf stop-calibration : service cluster manual-revert : service advanced-wips clear-event-history : service advanced-wips clear-event-history (dos-eap-failure- spoof|id-theft-out-of-sequence|id-theft-eapol-success-spoof-detected|wlan- jack-attack-detected|essid-jack-attack-detected|monkey-jack-attack- detected|null-probe-response-detected|fata-jack-detected|fake-dhcp-server- detected|crackable-wep-iv-used|windows-zero-config-memory-leak|multicast- all-systems-on-subnet|multicast-all-routers-on-subnet|multicast-ospf-all- routers-detection|multicast-ospf-designated-routers-detection|multicast- rip2-routers-detection|multicast-igmp-routers-detection|multicast-vrrp- agent|multicast-hsrp-agent|multicast-dhcp-server-relay-agent|multicast- igmp-detection|netbios-detection|stp-detection|ipx-detection|invalid- management-frame|invalid-channel-advertized|dos-deauthentication- detection|dos-disassociation-detection|dos-rts-flood|rogue-ap- detection|accidental-association|probe-response-flood|dos-cts-flood|dos- eapol-logoff-storm|unauthorized-bridge) : service start-shell : service pktcap on(bridge|drop|deny|router|wireless|vpn|radio (all|<1-3>) (|promiscuous)|rim|interface `WORD|ge <1-4>|me1|pc <1-4>|vlan <1-4094>')(|{direction (any|inbound|outbound)|acl-name WORD|verbose|hex|count <1-1000000>|snap <1-2048>|write (FILE|URL|tzsp WORD)|tcpdump})(|filter LINE) Mode : Profile Mode Command : service watchdog Mode : Radio Mode Command : service antenna-type (default|dual- band|omni|yagi|embedded|panel|patch|sector|out-omni|in-patch|AP4600-int) : service disable-erp
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 388 : service disable-ht-protection : service recalibration-interval <0-65535> ..........................................................................w m3400-34710C8> wm3400-34710C8>help search mint only-show Found 8 references for "mint" Mode : User Exec Command : show mint neighbors (|details)(|(on DEVICE-NAME)) : show mint links (|details)(|(on DEVICE-NAME)) : show mint id(|(on DEVICE-NAME)) : show mint stats(|(on DEVICE-NAME)) : show mint route(|(on DEVICE-NAME)) : show mint lsp : show mint lsp-db (|details)(|(on DEVICE-NAME)) : show mint mlcp(|(on DEVICE-NAME)) wm3400-34710C8> no Common Commands Negates a command or sets its default. Though the no command is common to the User Exec, Priv Exec, and Global Config modes, it negates a different set of commands in each mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no <PARAMETER> Parameters None
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 389 Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example Global Config mode: No command options wm3400-34710C8(config)#no ? aaa-policy Delete a aaa policy advanced-wips-policy Delete an advanced-wips policy AP4021 Delete an AP4021 access point AP4600 Delete an AP4600 access point AP4511 Delete an AP4511 access point AP4521 Delete an AP4521 access point AP4532 Delete an AP4532 access point AP4700 Delete an AP4700 access point association-acl-policy Delete an association-acl policy auto-provisioning-policy Delete an auto-provisioning policy captive-portal Delete a captive portal critical-resource-policy Remove device onboard critical resource policy customize Restore the custom cli commands to default device Delete multiple devices device-categorization Delete device categorization object dhcp-server-policy DHCP server policy dns-whitelist Delete a whitelist object event-system-policy Delete a event system policy firewall-policy Configure firewall policy igmp-snoop-policy Remove device onboard igmp snoop policy ip Internet Protocol (IP) mac MAC configuration management-policy Delete a management policy nac-list Delete an network access control list password-encryption Disable password encryption in configuration profile Delete a profile and all its associated configuration radio-qos-policy Delete a radio QoS configuration policy radius-group Local radius server group configuration radius-server-policy Remove device onboard radius policy radius-user-pool-policy Configure Radius User Pool rf-domain Delete one or more RF-domains and all their associated configurations WM3400 Delete an WM3400 wireless controller WM3600 Delete an WM3600 wireless controller WM3700 Delete an WM3700 wireless controller role-policy Role based firewall policy smart-rf-policy Delete a smart-rf-policy wips-policy Delete a wips policy wlan Delete a wlan object wlan-qos-policy Delete a wireless lan QoS configuration policy service Service Commands wm3400-34710C8(config)#
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 390 Priv Exec mode: No command options wm3400-34710C8#no ? adoption Reset adoption state of the device (& all devices adopted to it) captive-portal Captive portal commands crypto Encryption related commands debug Debugging functions logging Modify message logging facilities page Toggle paging service Service Commands terminal Set terminal line parameters upgrade Remove a patch wireless Wireless Configuration/Statistics commands wm3400-34710C8# user Exec mode: No command options wm3400-34710C8>no ? adoption Reset adoption state of the device (& all devices adopted to it) captive-portal Captive portal commands crypto Encryption related commands debug Debugging functions logging Modify message logging facilities page Toggle paging service Service Commands terminal Set terminal line parameters wireless Wireless Configuration/Statistics commands wm3400-34710C8> Related Commands revert Common Commands Reverts changes made to their last saved configuration no User Exec Commands mode no Priv Exec Commands mode no Global Config Commands mode
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 391 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax revert Parameters None Example wm3400-34710C8>revert wm3400-34710C8> service Common Commands Service commands are used to view and manage wireless controller configurations in all modes. The service commands and their corresponding parameters vary from mode to mode. The User Exec Mode and Priv Exec Mode commands provide same functionalities with a few minor changes. The Global Config service command sets the size of history files. It also enables viewing of CLI tree of the current mode.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 392 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax (User Exec Mode) service [advanced-wips|clear|cli-tables-expand|cli-tables-skin|cluster force-send-config|locator|noc|pktcap|radio|radius|set|show|smart- rf|wireless] service advanced-wips [clear-event-history|terminate-device <MAC>] service advanced-wips clear-event-history {accidental-association| crackable-wep-iv-used|dos-cts-flood|dos-deauthentication-detection| dos-disassociation-detection|dos-eap-failure-spoof|dos-eapol-logoff- storm| dos-rts-flood|essid-jack-attack-detected|fake-dhcp-server-detected| fata-jack-detected|id-theft-eapol-success-spoof-detected| id-theft-out-of-sequence|invalid-channel-advertized|invalid- management-frame| ipx-detection|monkey-jack-attack-detected|multicast-all-routers-on- subnet| multicast-all-systems-on-subnet|multicast-dhcp-server-relay-agent| multicast-hsrp-agent|multicast-igmp-detection|multicast-igrp- routers-detection| multicast-ospf-all-routers-detection|multicast-ospf-designated- routers-detection| multicast-rip2-routers-detection|multicast-vrrp-agent|netbios- detection| null-probe-response-detected|probe-response-flood|rogue-ap- detection| stp-detection|unauthorized-bridge|windows-zero-config-memory-leak| wlan-jack-attack-detected} service clear [ap-upgrade|command-history|noc|reboot-history|unsanctioned| upgrade-history|wireless] service clear ap-ugrade history {on <DOMAIN-NAME>} service clear [command-history|reboot-history|upgrade-history]{on <DEVICE- NAME>} service clear noc statistics service clear unsanctioned aps {on <DEVICE-OR-DOMAIN-NAME>}] service clear wireless [ap|client|radio|wlan] service clear wireless [ap|client] statistics {<MAC> {(on <DEVICE-OR- DOMAIN-NAME>)}
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 393 service clear wireless radio statistics {<MAC/HOSTNAME> <1-3> {(on <DEVICE- OR-DOMAIN- NAME>)} service clear wireless wlan statistics {<WLAN> {(on <DEVICE-OR-DOMAIN- NAME)} service cli-tables-expand {left|right} service cli-tables-skin [ansi|hashes|minimal|none|percent|stars|thick|thin| utf-8] {grid} service cluster force [active|configured-state|standby] service force-send-config {on <DEVICE-OR-DOMAIN-NAME>} service locator {on <DEVICE-NAME>} service noc parallel-updates <1-1024> service pktcap on [bridge|deny|drop|ext-vlan|interface|radio|rim|router| vpn|wireless] service pktcap on [bridge|deny|drop|ext-vlan|rim|router|vpn|wireless] {(acl-name <ACL>,count <1-1000000>,direction [any|inbound|outbound], filter <LINE>,hex,rate <1-100>,snap <1-2048>,tcpdump|verbose, write [file|url|tzsp [<IP/TZSP HOSTNAME>]])} service pktcap on interface [<INTERFACE>|ge <1-4>|me1|port-channel <1-2>| vlan <1-4094>] {(acl-name <ACL>,count <1-1000000>, direction [any|inbound|outbound],filter <LINE>,hex,rate <1-100>, snap <1-2048>,tcpdump|verbose,write [file|url|tzsp [<IP/TZSP HOSTNAME>]])} service pktcap on radio [<1-3>|all] {(acl-name <ACL>,count <1-1000000>, direction [any|inbound|outbound],filter <LINE>,hex,rate <1-100>, snap <1-2048>,tcpdump|verbose,write [file|url|tzsp [<IP/TZSP HOSTNAME>]])} service radio <1-3> dfs simulator-radar [extension|primary] service radius test [<IP>|<HOSTNAME>] [<WORD>|<PORT>] service radius test [<IP>|<HOSTNAME>] <WORD> <USERNAME> <PASSWORD> {wlan <WLAN> ssid <SSID> {(on <DEVICE-NAME>)}} service radius test [<IP>|<HOSTNAME>] <PORT> <1024-65535> <WORD> <USERNAME> <PASSWORD> {wlan <WLAN> ssid <SSID> {(on <DEVICE-NAME>)} service set validation-mode [full|partial] {on <DEVICE-NAME>} service show [advanced-wips|captive-portal|cli|command-history| configuration-revision|crash-info|dhcp-lease|diag|info|mac- vendor|mem| mint|noc|pm|process|reboot-history|rf-domain-manager|snmp|startup- log|sysinfo| top|upgrade-history|watch-dog|wireless|xpath-history]
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 394 service show advanced-wips stats [ap-table|client-table|connected-sensors- status| termination-entries] service show captive-portal [servers|user-cache] {on <DEVICE-NAME>} service show [cli|configuration-revision|mac-vendor <OUI/MAC>|noc diag| snmp session|xpath-history| service show [command-history|crash-info|info|mem|process|reboot-history| startup-log|sysinfo|top|upgrade-history|watchdog] {on <DEVICE-NAME>} service show dhcp-lease {<INTERFACE>|on|vlan <1-4094>} {(on <DEVICE-NAME>)} service show diag [led-status|stats] {on <DEVICE-NAME>} service show mint adopted-devices {on <DEVICE_NAME>} service show pm {history {(on <DEVICE-NAME>)}} service show rf-domain-manager diag {<MAC/HOSTNAME> {(on <DEVICE-OR-DOMAIN- NAME>)} service show wireless [aaa-stats|client|config-internal|credential-cache| dns-cache|neighbors|stats-client|vlan-usage]] service show wireless [aaa-stats|credential-cache|dns-cache] {on <DEVICE- NAME>} service show wireless [neighbors|vlan-usage] service show wireless client proc [info|stats] {<MAC> {{on <DEVICE-OR- DOMAIN- NAME>)}} service show wireless config-internal {include-factory}] service show wireless stats-client diag {<MAC/HOSTNAME> {(on <DEVICE-OR- DOMAIN-NAME>)}} service smart-rf [clear-config|clear-history|interactive-calibration| interactive-calibration-result|run-calibration|save-config|stop- calibration] service smart-rf [clear-config|clear-history|interactive-calibration| run-calibration|save-config|stop-calibration]{on <DOMAIN-NAME>} service smart-rf interactive-calibration-result [discard|replace-current- config| write-to-configuration]{on <DOMAIN-NAME>} service wireless [client|dump-core-snapshot|qos|wips] service wireless client beacon-request <MAC> mode [active|passive|table] ssid [<SSID>|any] channel-report [<CHANNEL-LIST>|none] {on <DEVICE-NAME>} service wireless qos delete-tspec <MAC> tid <0-7> service wireless wips [clear-client-blacklist|clear-event-history] service wireless wips clear-client-blacklist [all|mac <MAC> service wireless wips clear-event-history {on <DEVICE-OR-DOMAIN-NAME>}
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 395 Parameters (User Exec Mode) service advanced-wips clear-event-history {accidental-association| crackable-wep-iv-used|dos-cts-flood|dos-deauthentication-detection| dos-disassociation-detection|dos-eap-failure-spoof|dos-eapol-logoff-storm| dos-rts-flood|essid-jack-attack-detected|fake-dhcp-server-detected| fata-jack-detected|id-theft-eapol-success-spoof-detected| id-theft-out-of-sequence|invalid-channel-advertized|invalid-management- frame| ipx-detection|monkey-jack-attack-detected|multicast-all-routers-on-subnet| multicast-all-systems-on-subnet|multicast-dhcp-server-relay-agent| multicast-hsrp-agent|multicast-igmp-detection|multicast-igrp-routers- detection| multicast-ospf-all-routers-detection|multicast-ospf-designated-routers- detection| multicast-rip2-routers-detection|multicast-vrrp-agent|netbios-detection| null-probe-response-detected|probe-response-flood|rogue-ap-detection| stp-detection|unathorized-bridge|windows-zero-config-memory-leak| wlan-jack-attack-detected} advanced-wips clear-event- history The advanced Wireless Intrusion Prevention System (WIPS) service command clears event history and terminates a device. clear-event-history Clears event history based on the parameters passed accidental-association Optional. Clears accidental wireless client association event history crackable-wep-iv-used Optional. Clears crackable Wired Equivalent Privacy (WEP) IV used event history dos-cts-flood Optional. Clears DoS Clear-To-Send (CTS) flood event history dos-deauthentication- detection Optional. Clears DoS de-authentication detection event history dos-disassociation-detection Optional. Clears DoS disassociation detection event history dos-eap-failure-spoof Optional. Clears DoS Extensible Authentication Protocol (EAP) failure spoof detection event history dos-eapol-logoff-storm Optional. Clears DoS Extensible Authentication Protocol over LAN (EAPoL) logoff storm detection event history dos-rts-flood Optional. Clears DoS request-to-send (RTS) flood detection event history essid-jack-attack-detected Optional. Clears Extended Service Set ID (ESSID) jack attacks detection event history fake-dhcp-server-detected Optional. Clears fake DHCP server detection event history fata-jack-detected Optional. Clears fata-jack attacks detection event history id-theft-eapol-success-spoof- detected Optional. Clears IDs theft - EAPOL success spoof detection event history id-theft-out-of-sequence Optional. Clears IDs theft-out-of-sequence detection event history invalid-channel-advertized Optional. Clears invalid channel advertizement detection event history invalid-management-frame Optional. Clears invalid management frames detection event history ipx-detection Optional. Clears automatic IPX interface detection event history monkey-jack-attack-detected Optional. Detects monkey-jack attacks detection event history multicast-all-routers-on- subnet Optional. Clears all multicast routers on the subnet detection event history multicast-all-systems-on- subnet Optional. Clears all multicast systems on the subnet detection event history multicast-dhcp-server-relay- agent Optional. Clears multicast DHCP server relay agents detection event history
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 396 service advanced-wips terminate-device <MAC>] service clear ap-upgrade history {on <DOMAIN-NAME>}] service clear [command-history|reboot-history|upgrade-history] {on <DEVICE- NAME>} service clear noc statistics] multicast-hsrp-agent Optional. Clears multicast Hot Standby Router Policy (HSRP) agents detection event history multicast-igmp-detection Optional. Clears multicast Internet Group Management Protocol (IGMP) detection event history multicast-igrp-routers- detection Optional. Clears multicast Interior Gateway Router Protocol (IGRP) routers detection event history multicast-ospf-all-routers- detection Optional. Clears multicast Open Shortest Path First (OSPF) all routers detection event history multicast-ospf-designated- routers-detection Optional. Clears multicast OSPF designated routers detection event history multicast-rip2-routers- detection Optional. Clears multicast RIP2 routers detection event history multicast-vrrp-agent Optional. Clears multicast Virtual Router Redundancy Protocol (VRRP) agents detection event history netbios-detection Optional. Clears NetBIOS detection event history null-probe-response-detected Optional. Clears null probe response detection event history probe-response-flood Optional. Clears probe response flood detection event history rogue-ap-detection Optional. Clears rogue AP detection event history stp-detection Optional. Clears Spanning Tree Protocol (STP) detection event history unauthorized-bridge Optional. Clears unauthorized bridge detection event history windows-zero-config- memory-leak Optional. Clears Windows zero configuration memory leak detection event history wlan-jack-attack-detected Optional. Clears WLAN jack attack detection event history advanced-wips terminate- device <MAC> The advanced WIPS service command clears event history details, and terminates a device. terminate-device Terminates a specified device <MAC> Specify the MAC address of the AP or wireless client. clear ap-upgrade history Clears firmware upgrade history on <DOMAIN-NAME> Optional. Clears firmware upgrade details in a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name. clear [command-history| reboot-history| upgrade-history] Clears command history, reboot history, or device upgrade history on <DEVICE-NAME> Optional. Clears history on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. clear noc statistics Clears Network Operations Center (NOC) applicable statistics counters
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 397 service clear unsanctioned aps {on <DEVICE-OR-DOMAIN-NAME>}] service clear wireless [ap|client] {<MAC> {on <DEVICE-OR-DOMAIN-NAME>}| on <DEVICE-OR-DOMAIN-NAME>} service clear wireless radio statistics {<MAC/HOSTNAME> <1-3> {(on <DEVICE- OR-DOMAIN-NAME>)} service clear wireless wlan statistics {<WLAN> {(on <DEVICE-OR-DOMAIN- NAME>)} service cli-tables-expand {left|right} clear unsanctioned aps Clears the unsanctioned APs list on <DEVICE-OR-DOMAIN- NAME> Optional. Clears the list on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. clear wireless [ap|client] Clears applicable statistics counters AP Clears AP statistics counters client Clears wireless client statistics counters <MAC> {on <DEVICE-OR-DOMAIN- NAME>} Optional. Specify the MAC address of the AP. on <DEVICE-OR-DOMAIN-NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. clear wireless radio statistics Clears applicable wireless radio statistics counters <MAC/HOSTNAME> <1-3> Optional. Specify the MAC address or hostname of the radio, or append the interface number to form the radio ID in the AA-BB-CC-DD-EE-FF:RX or HOSTNAME:RX format. <1-3> Specify the radio interface index, if not specified as part of the radio ID. on <DEVICE-OR-DOMAIN- NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. clear wireless wlan statistics Clears WLAN statistics counters <WLAN> Clears statistics counters on a specified WLAN on <DEVICE-OR-DOMAIN- NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. cli-tables-expand Displays the CLI table in a drop-down format left Optional. Displays the output in a left-justified format right Optional. Displays the output in a right-justified format
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 398 service cli-tables-skin [ansi|hashes|minimal|none|percent|stars|thick|thin|utf-8] {grid} service cluster force [active|configured-state|standby] service force-send-config {on <DEVICE-OR-DOMAIN-NAME>} service locator {on <DEVICE-NAME>} service noc parallel-updates <1-1024> service pktcap on [bridge|deny|drop|ext-vlan|rim|router|vpn|wireless] {(acl-name <ACL>|count <1-1000000>|direction [any|inbound|outbound]| cli-tables-skin [ansi|hashes|minimal| none|percent| stars|thick| thin|uf-8] Selects a formatting layout or skin for CLI tabular outputs ansi Uses ANSI characters for borders hashes Uses hashes (#) for borders minimal Uses one horizontal line between title and data rows none Displays space separated items with no decoration percent Uses the percent sign (%) for borders stars Uses asterisks (*) for borders thick Uses thick lines for borders thin Uses thin lines for borders utf-8 Uses UTF-8 characters for borders grid Optional. Uses a complete grid instead of title lines cluster Enables cluster protocol management force Forces action commands on a cluster active Changes the cluster run status to active configured-state Restores a cluster to the configured state standby Changes the cluster run status to standby force-send-config Resends configuration details on <DEVICE-OR-DOMAIN- NAME> Optional. Resends configuration details to a device <DEVICE-OR-DOMAIN-NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. locator Enables LEDs on <DEVICE-NAME> Optional. Enables LEDs on a device <DEVICE-NAME> Specify name of the AP or wireless controller. noc Configures NOC wireless controller serviceability commands parallel-updates <1-1024> Sets a limit to the number of parallel threads <1-1024> Specify a value from 1 - 1024.
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 399 filter|hex|rate <1-100>|snap <1-2048>|tcpdump|verbose| write [file|url|tzsp <IP/TZSP HOSTNAME>])} pktcap on Captures data packets crossing at a specified location on Defines the packet capture location bridge Captures packets transiting through the Ethernet bridge deny Captures packets denied by an Access Control List (ACL) drop Captures packets at the drop locations ext-vlan Captures packets forwarded to or from an extended VLAN rim Captures packets at the Radio Interface Module (RIM) router Captures packets transiting through an IP router vpn Captures packets forwarded to or from a VPN link wireless Captures packets forwarded to or from a wireless device acl-name <ACL> Optional. Specify the ACL that matches the acl-name for the 'deny' location count <1-1000000> Optional. Limits the captured packet count. Specify a value from 1 -1000000. direction [any|inbound|outbound] Optional. Changes the packet direction with respect to a device. The direction can be set as any, inbound, or outbound.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 400 filter [<LINE>|arp|capwap|cdp|dot11 |dropreason|dst|ether| host|icmp|igmp|ip|ipv6|l2|l3|l4|ll dp|mint|net|not|port|priority|rad io|src|tcp|udp|vlan|wlan] Optional. Filters packets based on the option selected (must be used as a last option) The filter options are: <LINE> Defines user defined packet capture filter arp Matches ARP packets capwap Matches CAPWAP packets cdp Matches CDP packets dot11 Matches 802.11 packets dropreason Matches packet drop reason dst Matches IP destination ether Matches Ethernet packets host Matches host destination icmp Matches ICMP packets igmp Matches IGMP packets ip Matches IPV4 packets ipv6 Matches IPV6 packets l2 Matches L2 header l3 Matches L3 header l4 Matches L4 header lldp Matches LLDP packets mint Matches MiNT packets net Matches IP in subnet not Filters out any packet that matches the filter criteria (For example, if not TCP is used, all tcp packets are filtered out) port Matches TCP or UDP port priority Matches packet priority radio Matches radio src Matches IP source stp Matches STP packets tcp Matches TCP packets udp Match UDP packets vlan Matches VLAN wlan Matches WLAN hex Optional. Provides binary output of the captured packets rate <1-100> Optional. Specifies the packet capture rate <1-100> Specify a value from 1 - 100 seconds. snap <1-2048> Optional. Captures the data length <1-2048> Specify a value from 1 - 2048 characters. tcpdump Optional. Decodes tcpdump. The tcpdump analyzes network behavior, performance, and infrastructure. It also analyzes applications that generate or receive traffic. verbose Optional. Displays full packet body
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 401 service pktcap on radio [<1-3>|all] {(acl-name <ACL>|count <1-1000000>| direction [any|inbound|outbound]|filter <LINE>|hex|promiscuous|rate <1- 100>| snap <1-2048>|tcpdump|verbose|write [file|url|tzsp <IP/TZSP HOSTNAME>])} write Captures packets to a specified file. Provide the file name and location in the following format: FILE flash:/path/file cf:/path/file usb1:/path/file usb2:/path/file vram:startup-config URL tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file tzsp Tazman Sniffer Protocol (TZSP) host. Specify the TZSP hosts IP address or hostname. pktcap on radio [<1-3>|all] Captures data packets on a specified radio or on all radios (802.11) <1-3> Specify the radio index from 1 - 3. all Captures data packets on all radios (802.11) acl-name <ACL> Optional. Specify the ACL name. count <1-1000000> Optional. Sets a specified number of packets to capture <1-1000000> Specify a value from 1 -1000000. direction [any|inbound|outbound] Optional. Changes the packet direction with respect to a device. The direction can be set as any, inbound, or outbound. filter <LINE> Optional. Filters packets based on the option selected (must be used as a last option) <LINE> Define a packet capture filter or select any one of the available options. The options are: arp, capwap, cdp, dot11, dropreason, dst, ether, host, icmp, igmp, ip, ipv6, 12, 13, 14, lldp, mint, net, not, port, priority, radio, src, stp, tcp, udp, vlan, and wlan. hex Optional. Provides binary output of the captured packets promiscuous Optional. Enables limited promiscuous mode capture on the current channel (disables normal operation during the capture) rate <1-100> Optional. Specifies the packet capture rate <1-100> Specify a value from 1 - 100 seconds. snap <1-2048> Optional. Captures the data length <1-2048> Specify a value from 1 - 2048 characters. tcpdump Optional. Decodes the TCP dump verbose Optional. Provides verbose output
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 402 service pktcap on interface [<INTERFACE>|ge <1-4>|me|port-channel <1-2>| vlan <1-4094] {(acl-name <ACL>|count <1-1000000>|direction [any|inbound|outbound]| filter <LINE>|hex|rate <1-100>|snap <1-2048>|tcpdump|verbose| write [file|url|tzsp <IP/TZSP HOSTNAME>])} write Captures packets to a specified file. Provide the file name and location in the following format: FILE flash:/path/file cf:/path/file usb1:/path/file usb2:/path/file nvram:startup-config URL tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file tzsp The TZSP host. Specify the TZSP hosts IP address or hostname. pktcap on Captures data packets at a specified interface on Specify the capture location. interface [<INTERFACE>| ge <1-4>|me1| port-channel <1-2| vlan <1-4094>] Captures packets at a specified interface. The options are: <INTERFACE> Specify the interface name. ge <1-4> Selects a GigabitEthernet interface index from 1 - 4 me1 Selects the FastEthernet interface port-channel <1-2> Selects a port-channel interface index from 1- 2 vlan <1-4094> Selects a VLAN ID from 1 - 4094 acl-name <ACL> Optional. Specify the ACL that matches the ACL name for the 'deny' location count <1-1000000> Optional. Sets a specified number of packets to capture <1-1000000> Specify a value from 1 - 1000000. direction [any|inbound|outbound] Optional. Changes the packet direction with respect to a device. The direction can be set as any, inbound, or outbound. filter <LINE> Optional. Filters packets based on the option selected (must be used as a last option) <LINE> Define a packet capture filter or select any one of the available options. hex Optional. Provides binary output of the captured packets rate <1-100> Optional. Specifies the packet capture rate <1-100> Specify a value from 1 - 100 seconds. snap <1-2048> Optional. Captures the data length <1-2048> Specify a value from 1 - 2048 characters. tcpdump Optional. Decodes the TCP dump verbose Optional. Provides verbose output
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 403 service radio <1-3> dfs simulate-radar [extension|primary] service radius test [<IP>|<HOSTNAME>] <WORD> <USERNAME> <PASSWORD> {wlan <WLAN> ssid <SSID> {(on <DEVICE-NAME>)}} service radius test [<IP>|<HOSTNAME>] <PORT> <1024-65535> <WORD> <USERNAME> <PASSWORD> {wlan <WLAN> ssid <SSID> {(on <DEVICE-NAME>)}} write Captures packets to a specified file. Provide the file name and location in the following format: FILE flash:/path/file cf:/path/file usb1:/path/file usb2:/path/file nvram:startup-config URL tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>@<hostname|IP>[:port]>/path/file tzsp The TZSP host. Specify the TZSP hosts IP address or hostname. radio <1-3> Configures radios parameters <1-3> Specify the radio index from 1 - 3. dfs Enables Dynamic Frequency Selection (DFS) simulate-radar [extension|primary] Simulates the presence of a radar on a channel. Select the channel type from the following options: extension Simulates a radar on the radios current extension channel primary Simulates a radar on the radios current primary channel radius test Tests a RADIUS server account test Tests the RADIUS server account with user parameters [<IP>|<HOSTNAME>] Sets the IP address or hostname of the RADIUS server <IP> Specify the RADIUS servers IP address. <HOSTNAME> Specify the RADIUS servers hostname. <WORD> Specify the shared secret to logon to the RADIUS server. <USERNAME> Specify the name of the user for authentication. <PASSWORD> Specify the password. wlan <WLAN> ssid <SSID> Tests the local RADIUS WLAN. Specify the local RADIUS WLAN name. ssid <SSID> Specify the local RADIUS servers SSID. on <DEVICE-NAME> Optional. Performs the tests on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. radius test Tests a RADIUS server account test Tests the RADIUS server account with user parameters
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 404 service set validation-mode [full|partial] {on <DEVICE-NAME>} service show advanced-wips stats [ap-table|client-table| connected-sensors-status|termination-entries] service show captive-portal [servers|user-cache] {on <DEVICE-NAME>} service show [cli|configuration-revision|mac-vendor <OUI/MAC>|noc diag| snmp session|xpath-history] [<IP>|<HOSTNAME>] Sets the IP address or hostname of the RADIUS server <IP> Specify the RADIUS servers IP address. <HOSTNAME> Specify the RADIUS servers hostname. <PORT> <1024-65535> Specify the RADIUS server port from 1024 - 65535. The default port is 1812. <WORD> Specify the shared secret to logon to the RADIUS server. <USERNAME> Specify the name of the user for authentication. <PASSWORD> Specify the password. wlan <WLAN> ssid <SSID> Tests the RADIUS server on the local WLAN. Specify the local WLAN name. ssid <SSID> Specify the RADIUS servers SSID. on <DEVICE-NAME> Optional. Performs the tests on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. set Sets the validation mode for running configuration validation validation-mode [full|partial] Sets the validation mode full Performs a full configuration validation partial Performs a partial configuration validation on <DEVICE-NAME> Optional. Performs configuration validation on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed advanced-wips stats Displays advanced WIPS statistics ap-table Displays AP table statistics client-table Displays client table statistics connected-sensors-status Displays connected sensors statistics termination-entries Displays termination entries statistics show Displays running system statistics based on the parameters passed captive-portal Displays captive portal information servers Displays server information for active captive portals user-cache Displays cached user details for a captive portal on <DEVICE-NAME> Optional. Displays server information or cached user details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed cli Displays CLI tree of the current mode
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 405 service show [command-history|crash-info|info|mem|process|reboot-histroy| startup-log|sysinfo|top|upgrade-history|watchdog] {on <DEVICE-NAME>} service show dhcp-lease {<INTERFACE>|on|vlan <1-4094>} {(on <DEVICE-NAME>)} configuration-revision Displays current configuration revision number mac-vendor <OUI/MAC> Displays vendor name for a specified MAC address or Organizationally Unique Identifier (OUI) part of the MAC address <OUI/MAC> Specify the MAC address or its OUI. The first six digits of the MAC address is the OUI. Use the AABBCC or AA-BB-CC format to provide the OUI. noc diag Displays NOC diagnostic details snmp session Displays SNMP session details xpath-history Displays XPath history show Displays running system statistics based on the parameters passed command-history Displays command history (lists all commands executed) crash-info Displays information about core, panic, and AP dump files info Displays snapshot of available support information mem Displays a systems current memory usage (displays the total memory and available memory) process Displays active system process information (displays all processes currently running on the system) reboot-history Displays the devices reboot history startup-log Displays the devices startup log sysinfo Displays a systems memory usage top Displays system resource information upgrade-history Displays the devices upgrade history (displays details, such as date, time, and status of the upgrade, old version, new version etc.) watchdog Displays the devices watchdog status on <DEVICE-NAME> The following parameters are common to all of the above: on <DEVICE-NAME> Optional. Displays information for a specified device. If no device is specified, the system displays information for the logged device <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed dhcp-lease Displays DHCP lease information received from the server <INTERFACE> Displays DHCP lease information for a specified router interface <INTERFACE> Specify the router interface name. on Displays DHCP lease information for a specified device vlan <1-4094> Displays DHCP lease information for a VLAN <1-4094> Specify a VLAN index from 1 - 4094. on <DEVICE-NAME> Optional. Displays DHCP lease information for a specified device. If no device is specified, the system displays information for the logged device. <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 406 service show diag [led-staus|stats] {(on <DEVICE-NAME>)}] service show mint adopted-devices {(on <DEVICE-NAME>)}] service show pm {history {(on <DEVICE-NAME>)}}] service show rf-domain-manager diag {(<MAC/HOSTNAME> {(on <DEVICE-OR- DOMAIN-NAME>)}}] service show wireless [aaa-stats|credential-cache|dns-cache] {on <DEVICE- NAME>}] show Displays running system statistics based on the parameters passed diag Displays diagnostic statistics, such as LED status, fan speed, and sensor temperature led-status Displays LED state variables and the current state stats Displays fan speed and sensor temperature statistics on <DEVICE-NAME> Optional. Displays diagnostic statistics for a specified device. If no device is specified, the system displays information for the logged device. <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed mint Displays MiNT protocol details adopted-devices Displays adopted devices status in dpd2 on <DEVICE-NAME> Optional. Displays MiNT protocol details for a specified device. If no device is specified, the system displays information for the logged device. <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed pm Displays the Process Monitor (PM) controlled process details history Optional. Displays process change history (the time at which the change was implemented, and the events that triggered the change) on <DEVICE-NAME> Optional. Displays process change history for a specified device. If no device is specified, the system displays information for the logged device. <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed rf-domain-manager Displays RF Domain manager information diag Displays RF Domain manager related diagnostics statistics <MAC/HOSTNAME> Optional. Specify the MAC address or hostname of the RF Domain manager. on <DEVICE-OR-DOMAIN- NAME> Optional. Displays diagnostics statistics on a specified device or domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. show Displays running system statistics based on the parameters passed wireless Displays WLAN statistics (WLAN AAA policy, configuration parameters, VLAN usage etc.) aaa-stats Displays AAA policy statistics credential-cache Displays clients cached credentials statistics (VLAN, keys etc.)
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 407 service show wireless [neighbors|vlan-usage] {on <DEVICE-NAME>}] service show wireless client proc [info|stats] {<MAC> {(on <DEVICE-OR- DOMAIN-NAME)}}] service show wireless config-internal {include-factory}] service show wireless stats-client diag {<MAC/HOSTNAME> {(on <DEVICE-OR- DOMAIN-NAME)}}] dns-cache Displays cache of resolved names of servers related to wireless networking on <DEVICE-NAME> Optional. Displays WLAN statistics for a specified device. If no device is specified, the system displays information for the logged device. <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed wireless Displays WLAN statistics (WLAN AAA policy, configuration parameters, VLAN usage etc.) neighbors Displays neighboring device statistics for roaming and flow migration vlan-usage Displays VLAN statistics across WLANs on <DEVICE-NAME> Optional. Displays WLAN statistics for a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed wireless Displays WLAN statistics (WLAN AAA policy, configuration parameters, VLAN usage etc.) client Displays WLAN client statistics proc Displays dataplane proc entries These proc entries provide statistics on each wireless client on the WLAN. info Displays information of a specified wireless client stats Displays statistical data of a specified wireless client <MAC> Optional. Specify the MAC address of the wireless client. on <DEVICE-OR-DOMAIN- NAME> Optional. Displays information on a specified device or domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. show Displays running system statistics based on the parameters passed wireless Displays WLAN statistics (WLAN AAA policy, configuration parameters, VLAN usage etc.) config-internal Displays internal configuration parameters include-factory Optional. Displays factory default settings show Displays running system statistics based on the parameters passed wireless Displays WLAN statistics (WLAN AAA policy, configuration parameters, VLAN usage etc.) stats-client Displays managed AP statistics <MAC/HOSTNAME> Optional. Specify the MAC address or hostname of the AP.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 408 service smart-rf [clear-config|clear-history|interactive-calibration| run-calibration|save-config|stop-calibration] {on <DOMAIN-NAME>}] service smart-rf interactive-calibration-result [discard|replace-current- config|write-to-configuration] {on <DOMAIN-NAME>}] service wireless client beacon-request <MAC> mode [active|passive|table] ssid [<SSID>|any] channel-report [<CHANNEL-LIST>|none] {on <DEVICE-NAME>}] on <DEVICE-OR-DOMAIN- NAME> Optional. Displays statistics on a specified AP, or all APs on a specified domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. smart-rf Enables Smart RF management clear-config Clears WLAN Smart RF configuration on all devices clear-history Clears WLAN Smart RF history on all devices interactive-calibration Enables interactive Smart RF calibration run-calibration Starts a new Smart RF calibration process save-config Saves Smart RF configuration on all device, and also saves the history on the domain manager stop-calibration Stops Smart RF configuration, currently in progress on <DOMAIN-NAME> Optional. Enables Smart RF management on a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name. smart-rf Enables Smart RF management interactive-calibration-result Displays interactive Smart RF calibration results discard Discards interactive Smart RF calibration results replace-current-config Replaces current radio configuration write-to-configuration Writes and saves radio settings to configuration on <DOMAIN-NAME> Optional. Displays interactive Smart RF calibration results on a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name. wireless client beacon- requests Sends beacon measurement requests to a wireless client <MAC> Specify the MAC address of the wireless client. mode [active|passive|table] Specifies the beacon measurements mode Active Requests beacon measurements in the active mode Passive Requests beacon measurements in the passive mode Table Requests beacon measurements in the table mode ssid [<SSID>|any] Specifies if the measurements have to be made for a specified SSID or for any SSID <SSID> Requests beacon measurement for a specified SSID any Requests beacon measurement for any SSID
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 409 service wireless qos delete-tspec <MAC> tid <0-7> service wireless wips clear-client-blacklist [all|mac <MAC>] service wireless wips clear-event-history {on <DEVICE-OR-DOMAIN-NAME}] Syntax (Privilege Exec Mode) NOTE The service command of the Priv Exec Mode is the same as the service command in the User Exec Mode. There a few modifications that have been documented in this section. For the syntax and parameters of the other commands refer to the (User Exec Mode) syntax and (User Exec Mode) parameters sections of this chapter. service [advanced-wips|clear|cli-tables-expand|cli-tables- skin|cluster|copy| locator|mint|noc|pktcap|pm|radio|set|show|signal|smart-rf|start- shell|wireless] service copy tech-support [FILE|URL] service clear [ap-upgrade|command-history|crash-info|noc|reboot-history| unsanctioned|upgrade-history|wireless] channel-report [<CHANNEL- LIST>| none] Configures channel report in the request. The request can include a list of channels or can apply to all channels <CHANNEL-LIST> Request includes a list of channels. The client has to send beacon measurements only for those channels included in the request none Request applies to all channels on <DEVICE-NAME> Optional. Sends requests on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. wireless qos delete-tspec Sends a delete TSPEC request to a wireless client <MAC> Specify the MAC address of the wireless client. tid <0-7> Deletes the Traffic Identifier (TID) <0-7> Select the TID from 0 - 7. wireless wips Enables management of WIPS parameters clear-client-blacklist [all|mac <MAC>] Removes a specified client or all clients from the blacklist all Removes all clients from the blacklist mac <MAC> Removes a specified client form the blacklist <MAC> Specify the MAC address of the wireless client. wireless wips Enables WIPS management clear-event-history Clears event history on <DEVICE-OR-DOMAIN- NAME> Optional. Clears event history on a device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 410 service mint [clear [lsp-db|mlcp ]|debug-log [flash-and-syslog|flash-only]| expire [lsp|spf]|flood [csnp|lsp]|silence] service signal [abort <PROCESS>|kill <PROCESS>] service pm stop{on <DEVICE-NAME>} service show [advanced-wips|captive-portal|cli|command-history|crash-info| dhcp-lease|diag|info|last-passwd|mac- vendor|mem|noc|pm|process|reboot-history| rf-domain-manager|snmp|startup-log|sysinfo|top|upgrade- history|watchdog| wireless|xpath-history] service start-shell Parameters (Privilege Exec Mode) service copy tech-support <FILE> <URL> service clear crash-info {on <DEVICE-NAME>} service mint [clear [lsp-dp|mlcp]|debug-log [flash-and-syslog|flash- only]|expire [lsp|spf]|flood [csnp|lsp]|silence] copy tech-support Copies files for technical support tech-support Copies extensive system information useful for troubleshooting <FILE> Specify the file name in the following format: cf:/path/file usb1:/path/file usb2:/path/file <URL> Specify the file location in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>:<passwd>@<hostname|IP>[:port]>/path/file clear crash-info Clears all crash files on <DEVICE-NAME> Optional. Clears crash files on a specified device. These crash files are core, panic, and AP dump <DEVICE-NAME> Specify the name of the AP or wireless controller. mint Enables MiNT protocol management (clears LSP database, enables debug logging, enables running silence etc.) clear [lsp-dp|mlcp] Clears LSP database and MiNT Link Control Protocol (MLCP) links lsp-dp Clears MiNT Label Switched Path (LSP) database mlcp Clears MLCP links debug-log [flash-and-syslog| flash-only] Enables debug message logging flash-and-syslog Logs debug messages to the flash and syslog files flash-only Logs debug messages to the flash file only
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 411 service pm stop {on <DEVICE-NAME>} service show last-passwd service signal [abort <PROCESS>|kill <PROCESS>] service start-shell Syntax (Global Config Mode) service [set|show cli] service set [command-history <10-300>|upgrade-history <10-100>| reboot-history <10-100>] {on <DEVICE-NAME>} Parameters (Global Config Mode) service set [command-history <10-300>|upgrade-history <10-300>|reboot- history <10-300>] {on <DEVICE-NAME>} expire [lsp|spf] Forces expiration of LSP and recalculation of Shortest Path First (SPF) lsp Forces expiration of LSP spf Forces recalculation of SPF flood [csnp|lsp] Floods control packets csnp Floods our Complete Sequence Number Packets (CSNP) lsp Floods our LSP silence Run silent pm Stops the Process Monitor (PM) stops Stops the PM from monitoring all daemons on <DEVICE-NAME> Optional. Stops the PM on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. show Displays running system statistics based on the parameters passed last-passwd Displays the last password used to enter shell signal Sends a signal to a process tech-support Copies extensive system information useful for troubleshooting abort Sends an abort signal to a process, and forces it to dump to core <PROCESS> Specify the process name. kill Sends a kill signal to a process, and forces it to terminate without a core <PROCESS> Specify the process name. start-shell Provides shell access set Sets the size of history files command-history <10-300> Sets the size of the command history file <10-300> Specify a value from 10 - 300. The default is 200.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 412 service show cli Example wm3400-34710C8>service cli-tables-skin stars wm3400-34710C8> wm3400-34710C8>service pktcap on interface vlan 2 Capturing up to 50 packets. Use Ctrl-C to abort. wm3400-34710C8>service show cli User Exec mode: +-do +-help [help] +-show +-configuration-tree [help show configuration-tree] +-search +-WORD [help search WORD (|detailed|only-show|skip-show)] +-detailed [help search WORD (|detailed|only-show|skip-show)] +-only-show [help search WORD (|detailed|only-show|skip-show)] +-skip-show [help search WORD (|detailed|only-show|skip-show)] +-show +-commands [show commands] +-running-config [show (running-config|session-config) (|include- factory)] +-include-factory [show (running-config|session-config) (|include- factory)] +-interface [show running-config interface (|`WORD|ge <1-4>|me1|pc <1- 4>|vlan <1-4094>') (|include-factory)] +-WORD [show running-config interface (|`WORD|ge <1-4>|me1|pc <1- 4>|vlan <1-4094>') (|include-factory)] +-include-factory [show running-config interface (|`WORD|ge <1- 4>|me1|pc <1-4>|vlan <1-4094>') (|include-factory)] +-ge +-<1-4> [show running-config interface (|`WORD|ge <1-4>|me1|pc <1- 4>|vlan <1-4094>') (|include-factory)] +-include-factory [show running-config interface (|`WORD|ge <1- 4>|me1|pc <1-4>|vlan <1-4094>') (|include- factory)].................................................................w m3400-34710C8 wm3400-34710C8>service show general stats on wm3400-34710C8 upgrade-history <10-100> Sets the size of the upgrade history file <10-100> Specify a value from 10 - 100. The default is 50. reboot-history <10-100> Sets the size of the reboot history file <10-100> Specify a value from 10 - 100. The default is 50. on <DEVICE-NAME> Optional. Sets the size of history files on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. show cli Displays running system configuration details cli Displays the CLI tree of the current mode
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 413 Current Fan Speed: 6540 Minimum Fan Speed: TBD Hysteresis: TBD Sensor 1 Temperature: 31C Sensor 2 Temperature: 55C Sensor 3 Temperature: 29C Sensor 4 Temperature: 28C Sensor 5 Temperature: 26C Sensor 6 Temperature: 28C wm3400-34710C8> wm3400-34710C8>service wireless wips clear-mu-blacklist mac 11-22-33-44-55- 66 wm3400-34710C8> wm3400-34710C8#service signal kill testp Sending a kill signal to testp wm3400-34710C8# wm3400-34710C8#service signal abort testprocess Sending an abort signal to testprocess wm3400-34710C8# wm3400-34710C8#service mint clear lsp-db wm3400-34710C8# wm3400-34710C8#service mint silence wm3400-34710C8# wm3400-34710C8#service pm stop on wm3400-34710C8 wm3400-34710C8# wm3400-34710C8(config)#service show cli Global Config mode: +-help [help] +-search +-WORD [help search WORD (|detailed|only-show|skip-show)] +-detailed [help search WORD (|detailed|only-show|skip-show)] +-only-show [help search WORD (|detailed|only-show|skip-show)] +-skip-show [help search WORD (|detailed|only-show|skip-show)] +-show +-commands [show commands] +-eval +-LINE [show eval LINE] +-debugging [show debugging (|(on DEVICE-OR-DOMAIN-NAME))] +-cfgd [show debugging cfgd] +-on +-DEVICE-OR-DOMAIN-NAME [show debugging (|(on DEVICE-OR-DOMAIN- NAME))] +-wireless [show debugging wireless (|(on DEVICE-OR-DOMAIN-NAME))] +-on +-DEVICE-OR-DOMAIN-NAME [show debugging wireless (|(on DEVICE-OR- DOMAIN-NAME))] +-voice [show debugging voice (|(on DEVICE-OR-DOMAIN-NAME))]
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 414 +-on +-DEVICE-OR-DOMAIN-NAME [show debugging voice (|(on DEVICE-OR- DOMAIN-NAME))] +-captive-portal [show debugging captive-portal (|(on DEVICE-OR-DOMAIN- NAME))] +-on +-DEVICE-OR-DOMAIN-NAME [show debugging captive-portal (|(on DEVICE-OR-DOMAIN-NAME))] +-dhcpsvr [show debugging dhcpsvr (|(on DEVICE-NAME))] +-on.............................................................. wm3400-34710C8(config)# wm3400-34710C8#service traceroute -h traceroute: invalid option -- h BusyBox v1.14.1 () multi-call binary Usage: traceroute [-FIldnrv] [-f 1st_ttl] [-m max_ttl] [-p port#] [-q nqueries] [-s src_addr] [-t tos] [-w wait] [-g gateway] [-i iface] [-z pausemsecs] HOST [data size] Trace the route to HOST Options: -F Set the don't fragment bit -I Use ICMP ECHO instead of UDP datagrams -l Display the ttl value of the returned packet -d Set SO_DEBUG options to socket -n Print hop addresses numerically rather than symbolically -r Bypass the normal routing tables and send directly to a host -v Verbose -m max_ttl Max time-to-live (max number of hops) -p port# Base UDP port number used in probes (default is 33434) -q nqueries Number of probes per 'ttl' (default 3) -s src_addr IP address to use as the source address -t tos Type-of-service in probe packets (default 0) -w wait Time in seconds to wait for a response (default 3 sec) -g Loose source route gateway (8 max) wm3400-34710C8# wm3400-34710C8>ser show ap configured -------------------------------------------------------------------------- IDX NAME MAC PROFILE RF-DOMAIN ADOPTED-BY -------------------------------------------------------------------------- 1 ap4700-889EC4 00-15-70-88-9E-C4 default-AP4731 default un- adopted 2 AP4600-445566 11-22-33-44-55-66 default-AP4600 default un- adopted
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 415 3 AP4600-000000 00-A0-F8-00-00-00 default-AP4600 default 00-15-70-37-FA-BE -------------------------------------------------------------------------- wm3400-34710C8> wm3400-34710C8>service show command-history on wm3400-34710C8 Configured size of command history is 200 Date & Time User Location Command ===================================================================== Jul 28 16:39:34 2010 admin 172.16.10.10 17 service locator on wm3400-34710C8 Jul 28 16:39:13 2010 admin 172.16.10.10 17 exit Jul 28 16:17:51 2010 admin 172.16.10.10 17 exit Jul 28 16:15:58 2010 admin 172.16.10.10 17 exit Jul 28 16:15:53 2010 admin 172.16.10.10 17 advanced-wips-policy test Jul 28 16:08:13 2010 admin 172.16.10.10 17 exit Jul 28 15:24:25 2010 admin 172.16.10.10 16 firewall-policy test Jul 28 13:51:59 2010 admin 172.16.10.10 15 exit Jul 28 13:51:47 2010 admin 172.16.10.10 15 exit Jul 28 13:51:44 2010 admin 172.16.10.10 15 exit Jul 28 13:51:43 2010 admin 172.16.10.10 15 exit Jul 28 13:21:17 2010 admin 172.16.10.10 15 aaa-policy test Jul 28 13:20:35 2010 admin 172.16.10.10 15 exit Jul 28 13:09:14 2010 admin 172.16.10.10 15 exit Jul 28 13:08:44 2010 admin 172.16.10.10 15 aaa-policy test Jul 27 13:46:46 2010 admin 172.16.10.10 6 ip nat pool pool1 prefix-length 1 Jul 27 13:44:46 2010 admin 172.16.10.10 6 profile WM3700 default-WM3700 Jul 27 12:39:29 2010 admin 172.16.10.12 5 reload force Jul 27 12:28:41 2010 admin 172.16.10.12 20 reload force Jul 27 12:28:39 2010 admin 172.16.10.12 20 write memory .................................................................. wm3400-34710C8> wm3400-34710C8>service show diag stats on wm3400-34710C8 fan 1 current speed: 6660 min_speed: 2000 hysteresis: 250 fan 2 current speed: 6720 min_speed: 2000 hysteresis: 250 fan 3 current speed: 6540 min_speed: 2000 hysteresis: 250 Sensor 1 Temperature 32.0 C Sensor 2 Temperature 58.0 C Sensor 3 Temperature 29.0 C Sensor 4 Temperature 28.0 C Sensor 5 Temperature 26.0 C Sensor 6 Temperature 28.0 C wm3400-34710C8>service show info on rwm3400-34710C8 7.7M out of 8.0M available for logs. 9.4M out of 10.0M available for history. 19.2M out of 20.0M available for crashinfo.
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 416 List of Files: cfgd.log 5.7K Jul 28 17:17 fmgr.log 221 Jul 27 12:40 messages.log 1.0K Jul 27 12:41 startup.log 52.3K Jul 27 12:40 command.history 903 Jul 28 16:39 reboot.history 1.6K Jul 27 12:40 ugrade.history 698 Jul 27 12:39 Please export these files or delete them for more space. wm3400-34710C8> wm3400-34710C8E>service show upgrade-history on wm3400-34710C8 Configured size of upgrade history is 50 Date & Time Old Version New Version Status ===================================================================== Jul 27 12:37:30 2010 5.3.0.0-098D 5.3.0.0-097B Successful Jul 27 12:26:34 2010 5.3.0.0-097B 5.3.0.0-098D Successful Jul 22 16:33:04 2010 5.3.0.0-096B 5.3.0.0-097B Successful Jul 22 16:32:15 2010 5.3.0.0-096B 5.3.0.0-096B Unable to get update file. ftpget: cannot connect to remote host (172.16.10.1): Connection refused Jul 19 17:51:29 2010 5.3.0.0-090D 5.3.0.0-096B Successful Jul 12 12:41:12 2010 5.3.0.0-088D 5.3.0.0-090D Successful Jul 06 12:38:49 2010 5.3.0.0-086D 5.3.0.0-088D Successful Jun 29 13:06:50 2010 5.3.0.0-084D 5.3.0.0-086D Successful .......................................................... wm3400-34710C8 wm3400-34710C8>service show watchdog watchdog is enabled countdown: 255 seconds of 260 remain until reset wm3400-34710C8> wm3400-34710C8>service show xpath-history --------------------------------------------------------------------------- --------- DATE&TIME USER XPATH DURATION(MS) --------------------------------------------------------------------------- --------- Wed Jul 28 17:29:49 2010 [system] /wing-stats/device/00-A0-F8-00-00- 00/_internal/adjust_stats_interval 40 Wed Jul 28 17:29:49 2010 [system] /wing-stats/device/00-15-70-37-FA- BE/_internal/adjust_stats_interval 16 Wed Jul 28 17:29:43 2010 [system] /wing-stats/device/00-A0-F8-00-00- 00/_internal/adjust_stats_interval 39 Wed Jul 28 17:29:43 2010 [system] /wing-stats/device/00-15-70-37-FA- BE/_internal/adjust_stats_interval 16 Wed Jul 28 17:29:37 2010 [system] /wing-stats/device/00-A0-F8-00-00- 00/_internal/adjust_stats_interval 40 Wed Jul 28 17:29:37 2010 [system] /wing-stats/device/00-15-70-37-FA- BE/_internal/adjust_stats_interval 17
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 417 Wed Jul 28 17:29:31 2010 [system] /wing-stats/device/00-A0-F8-00-00- 00/_internal/adjust_stats_interval 40 Wed Jul 28 17:29:31 2010 [system] /wing-stats/device/00-15-70-37-FA- BE/_internal/adjust_stats_interval 16 Wed Jul 28 17:29:30 2010 [system] /wing-stats/device/00-15-70-37-FA- BE/watchdog-status 6 wm3400-34710C8#service show last-passwd Last password used: password with MAC 00:15:70:37:fa:be wm3400-34710C8# wm3400-34710C8>service show wireless ap diag on wm3400-34710C8 --------------------------------------------------------------------------- ----- AP-MAC FIELD VALUE --------------------------------------------------------------------------- ----- 00-15-70-37-FA-BE is_manager True 00-15-70-37-FA-BE last_stats_upload 107802.617188 00-15-70-37-FA-BE manager_mint_id 70.37.FA.BE 00-15-70-37-FA-BE max_pull_time 2.80668640137 00-15-70-37-FA-BE num_adoptions 0 00-15-70-37-FA-BE num_config_failed 0 00-15-70-37-FA-BE num_config_received 0 00-15-70-37-FA-BE num_stats_pulled 17951 00-15-70-37-FA-BE num_stats_pushed 0 00-15-70-37-FA-BE upload_state master --------------------------------------------------------------------------- --------- AP-MAC FIELD VALUE -------------------------------------------------------------------------- 00-A0-F8-00-00-00 is_manager False 00-A0-F8-00-00-00 last_stats_upload 449767.65625 00-A0-F8-00-00-00 manager_mint_id 70.37.FA.BE 00-A0-F8-00-00-00 max_pull_time 0 00-A0-F8-00-00-00 num_adoptions 2 00-A0-F8-00-00-00 num_config_applied 2 00-A0-F8-00-00-00 num_config_failed 0 00-A0-F8-00-00-00 num_config_received 2 00-A0-F8-00-00-00 num_stats_pulled 74796 00-A0-F8-00-00-00 num_stats_pushed 3 00-A0-F8-00-00-00 upload_state connected -------------------------------------------------------------------------- Total number of APs displayed: 2 wm3400-34710C8> wm3400-34710C8>service show wireless config-internal ! Startup-Config-Playback Completed: Yes no debug wireless no country-code ! wlan-qos-policy default no rate-limit wlan to-air no rate-limit wlan from-air
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 418 no rate-limit client to-air no rate-limit client from-air ! wlan wlan1 ssid wlan1 vlan 1 qos-policy default encryption-type none authentication-type none no accounting radius no accounting syslog wm3400-34710C8> System Information: Free RAM: 68.0% (169 of 249) Min: 10.0% File Descriptors: free: 24198 used: 960 max: 25500 CPU load averages: 1 min: 0.0% 5 min: 0.0% 15 min: 0.0% Kernel Buffers: Size: 32 64 128 256 512 1k 2k 4k 8k 16k 32k 64k 128k Usage: 2761 2965 927 201 549 107 141 25 68 0 1 2 0 Limit: 32768 8192 4096 4096 8192 8192 16384 16384 1024 512 256 64 64 wm3400-34710C8# wm3400-34710C8>service clear wireless radio statistics on wm3400-34710C8 clear radio stats on *: o.k. wm3400-34710C8#service show dhcp-lease vlan 1 on wm3400-34710C8 No dhcp lease information available wm3400-34710C8# show Common Commands Displays specified system component settings. There are a number of ways to invoke the show command: When invoked without any arguments, it displays information about the current context. If the current context contains instances, the show command (usually) displays a list of these instances. When invoked with the display parameter, it displays information about that component.
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 419 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show <parameter> Parameters None Example wm3400-34710C8#show ? adoption Display information related to adoption to wireless controller advanced-wips Advanced WIPS ap-upgrade AP Upgrade boot Display boot configuration. captive-portal Captive portal commands cdp Cisco Discovery Protocol clock Display system clock cluster Cluster Protocol commands Show command lists context Information about current context critical-resources Critical Resources crypto Encryption related commands debug Show Debugging status debugging Debugging functions device-categorization Device Categorization event-history Display event history event-system-policy Display event system policy file Display filesystem information firewall Wireless Firewall interface Interface Configuration/Statistics commands ip Internet Protocol (IP) ip-access-list-stats IP Access list stats licenses Show installed licenses and usage lldp Link Layer Discovery Protocol logging Show logging information
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 420 mac-access-list-stats MAC Access list stats mac-address-table Display MAC address table mint MiNT protocol noc Noc-level information ntp Network time protocol password-encryption Pasword encryption power Show power over ethernet command reload Scheduled reload information remote-debug Show details of remote debug sessions rf-domain-manager Show RF Domain Manager selection details role Role based firewall running-config Current operating configuration session-changes Configuration changes made in this session session-config This session configuration sessions Display CLI sessions smart-rf Smart-RF Management Commands spanning-tree Display spanning tree information startup-config Startup configuration terminal Display terminal configuration parameters timezone The timezone upgrade-status Display last image upgrade status version Display software & hardware version wireless Wireless commands wwan Display wireless WAN Status wm3400-34710C8# NOTE For more information on the show command, see Chapter 7, Show Commands. write Common Commands Writes the system running configuration to memory or terminal
Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 421 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax write [memory|terminal] Parameters write [memory|terminal] Example wm3400-34710C8>write memory [OK] wm3400-34710C8> wm3400-34710C8>write terminal ! ! Configuration of WM3700 version 5.3.0.0-048B ! ! version 2.1 ! ! smart-rf-policy default ! smart-rf-policy test enable calibration wait-time 4 ! wlan-qos-policy default ! wlan-qos-policy test voice-prioritization svp-prioritization wmm background cw-max 8 wmm video txop-limit 9 memory Writes to the non-volatile (NV) memory terminal Writes to terminal
Chapter 6: Common Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 422 wm3400-34710C8>
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 423 C H A P T E R 7 Show Commands Show commands display information about a configuration setting or display statistical information. Use this command to see the current running configuration as well as the start-up configuration. The show command also displays the configuration of the current context. This chapter describes the show CLI commands used in the USER EXEC, PRIV EXEC, and GLOBAL CONFIG modes. Commands entered in either USER EXEC mode or PRIV EXEC mode are referred to as EXEC mode commands. If a user or privilege is not specified, the referenced command can be entered in either mode. This chapter also describes the show commands in the GLOBAL CONFIG mode. The commands can be entered in all three modes, except commands like file, IP access list stats, MAC access list stats, and upgrade stats, which cannot be entered in the User Executable Mode. show commands Table summarizes show commands Command Description Reference show Displays settings for the specified system component page 7-425 adoption Displays information related to wireless controller adoption page 7-430 advanced-wips Displays advanced WIPS settings page 7-432 ap-upgrade Displays access point software image upgrade information page 7-435 boot Displays a device boot configuration page 7-437 captive-portal Displays WLAN hotspot functions page 7-439 cdp Displays a Cisco Discovery Protocol (CDP) neighbor table page 7-442 clock Displays the software system clock page 7-444 cluster Displays cluster commands page 7-445 commands Displays command list page 7-447 context Displays information about the current context page 7-449 critical-resources Displays critical resource information page 7-451 crypto Displays encryption mode information page 7-452 debug Displays debugging configuration information page 7-455 debugging Displays debugging configuration information page 7-458
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 424 device- categorization Displays device categorization details page 7-458 event-history Displays event history page 7-461 event-system- policy Displays event system policy configuration information page 7-463 file Displays file system information page 7-464 firewall Displays wireless firewall information page 7-466 interface Displays wireless controller interface status page 7-470 ip Displays Internet Protocol (IP) related information page 7-473 ip-access-list-stats Displays IP access list statistics page 7-480 l2tpv3 Displays L2TPv3 information page 7-482 licenses Displays installed licenses and usage information page 7-484 lldp Displays Link Layer Discovery Protocol (LLDP) information page 7-485 logging Displays logging information page 7-486 mac-access-list- stats Displays MAC access list statistics page 7-488 mac-address- table Displays MAC address table entries page 7-489 mint Displays MiNT protocol configuration commands page 7-491 noc Displays Noc-level information page 7-494 ntp Displays Network Time Protocol (NTP) information page 7-497 password- encryption Displays password encryption status page 7-499 power Displays Power over Ethernet (PoE) information page 7-500 remote-debug Displays remote debug session data page 7-502 rf-domain- manager Displays RF Domain manager selection details page 7-503 role Displays role-based firewall information page 7-504 running-config Displays contents of configuration files page 7-505 session-changes Displays configuration changes made in this session page 7-509 session-config Displays a list of currently active open sessions on the device page 7-510 sessions Displays CLI sessions page 7-512 smart-rf Displays Smart RF management commands page 7-513 spanning-tree Displays spanning tree information page 7-516 startup-config Displays complete startup configuration script on the console page 7-520 terminal Displays terminal configuration parameters page 7-522 timezone Displays timezone page 7-523 upgrade-status Displays image upgrade status page 7-524 version Displays a devices software and hardware version page 7-526 vrrp Displays VRRP information page 7-527 what Displays details of a specified search phrase page 7-529 wireless Displays wireless configuration parameters page 7-530 wwan Displays wireless WAN status page 7-541 Command Description Reference
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 425 show show commands The show command displays the following information: A devices current configuration A devices start up configuration A devices current context configuration, such as profiles and policies Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show <parameter> Parameters None Example The following examples list the show commands in the different modes: GLOBAL CONFIG Mode wm3400-34710C8(config)#show ? adoption Display information related to adoption to wireless controller advanced-wips Advanced WIPS ap-upgrade AP Upgrade boot Display boot configuration. captive-portal Captive portal commands cdp Cisco Discovery Protocol clock Display system clock cluster Cluster Protocol commands Show command lists context Information about current context critical-resources Critical Resources
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 426 crypto Encryption related commands debug Show Debugging status debugging Debugging functions device-categorization Device Categorization event-history Display event history event-system-policy Display event system policy file Display filesystem information firewall Wireless Firewall interface Interface Configuration/Statistics commands ip Internet Protocol (IP) ip-access-list-stats IP Access list stats licenses Show installed licenses and usage lldp Link Layer Discovery Protocol logging Show logging information mac-access-list-stats MAC Access list stats mac-address-table Display MAC address table mint MiNT protocol noc Noc-level information ntp Network time protocol password-encryption Pasword encryption power Show power over ethernet command reload Scheduled reload information remote-debug Show details of remote debug sessions rf-domain-manager Show RF Domain Manager selection details role Role based firewall running-config Current operating configuration session-changes Configuration changes made in this session session-config This session configuration sessions Display CLI sessions smart-rf Smart-RF Management Commands spanning-tree Display spanning tree information startup-config Startup configuration terminal Display terminal configuration parameters timezone The timezone upgrade-status Display last image upgrade status version Display software & hardware version wireless Wireless commands wwan Display wireless WAN Status wm3400-34710C8(config)# wm3400-34710C8(config)# wm3400-34710C8(config)#show clock 2011-04-30 09:28:29 GMT PRIVILEGE EXEC Mode wm3400-34710C8#show ? adoption Display information related to adoption to wireless controller advanced-wips Advanced WIPS ap-upgrade AP Upgrade boot Display boot configuration.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 427 captive-portal Captive portal commands cdp Cisco Discovery Protocol clock Display system clock cluster Cluster Protocol commands Show command lists context Information about current context critical-resources Critical Resources crypto Encryption related commands debug Show Debugging status debugging Debugging functions device-categorization Device Categorization event-history Display event history event-system-policy Display event system policy file Display filesystem information firewall Wireless Firewall interface Interface Configuration/Statistics commands ip Internet Protocol (IP) ip-access-list-stats IP Access list stats licenses Show installed licenses and usage lldp Link Layer Discovery Protocol logging Show logging information mac-access-list-stats MAC Access list stats mac-address-table Display MAC address table mint MiNT protocol noc Noc-level information ntp Network time protocol password-encryption Pasword encryption power Show power over ethernet command reload Scheduled reload information remote-debug Show details of remote debug sessions rf-domain-manager Show RF Domain Manager selection details role Role based firewall running-config Current operating configuration session-changes Configuration changes made in this session session-config This session configuration sessions Display CLI sessions smart-rf Smart-RF Management Commands spanning-tree Display spanning tree information startup-config Startup configuration terminal Display terminal configuration parameters timezone The timezone upgrade-status Display last image upgrade status version Display software & hardware version wireless Wireless commands wwan Display wireless WAN Status wm3400-34710C8# wm3400-34710C8#show terminal wm3400-34710C8#show terminal Terminal Type: xterm Length: 24 Width: 80
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 428 USER EXEC Mode wm3400-34710C8>show ? adoption Display information related to adoption to wireless controller advanced-wips Advanced WIPS ap-upgrade AP Upgrade captive-portal Captive portal commands cdp Cisco Discovery Protocol clock Display system clock cluster Cluster Protocol commands Show command lists context Information about current context critical-resources Critical Resources crypto Encryption related commands debug Show Debugging status debugging Debugging functions device-categorization Device Categorization event-history Display event history event-system-policy Display event system policy firewall Wireless Firewall interface Interface Configuration/Statistics commands ip Internet Protocol (IP) licenses Show installed licenses and usage lldp Link Layer Discovery Protocol logging Show logging information mac-address-table Display MAC address table mint MiNT protocol noc Noc-level information ntp Network time protocol password-encryption Pasword encryption power Show power over ethernet command remote-debug Show details of remote debug sessions rf-domain-manager Show RF Domain Manager selection details role Role based firewall running-config Current operating configuration session-changes Configuration changes made in this session session-config This session configuration sessions Display CLI sessions smart-rf Smart-RF Management Commands spanning-tree Display spanning tree information startup-config Startup configuration terminal Display terminal configuration parameters timezone The timezone version Display software & hardware version wireless Wireless commands wwan Display wireless WAN Status wm3400-34710C8> wm3400-34710C8>show wireless ap configured --------------------------------------------------------------------------
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 429 IDX NAME MAC PROFILE RF-DOMAIN ADOPTED- BY -------------------------------------------------------------------------- 1 AP4731-889EC4 00-15-70-88-9E-C4 default-AP4731 default un- adopted 2 AP4600-445566 11-22-33-44-55-66 default-AP4600 default un- adopted -------------------------------------------------------------------------- wm3400-34710C8>
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 430 adoption show commands The adoption command is common to all three modes. It displays information related to APs adopted by a wireless controller. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show adoption [config-errors|history|info|offline|pending|status] show adoption [config-errors <DEVICE-NAME>|history {on <DEVICE-NAME>}| info {on <DEVICE-NAME>}|offline|pending {on <DEVICE-NAME>}| status {on <DEVICE-NAME>}] Parameters show adoption [config-errors <DEVICE-NAME>|history {on <DEVICE-NAME>}|info {on <DEVICE-NAME>}|offline|pending {on <DEVICE-NAME>}|status {on-<DEVICE- NAME>}] adoption Displays an AP adoption history and status. It also displays adopted device configuration errors. config-errors <DEVICE-NAME> Displays configuration errors of an AP or all APs adopted by a wireless controller <DEVICE-NAME> Specify the name of the AP or wireless controller. history {on <DEVICE-NAME>} Displays adoption history status on <DEVICE-NAME> Optional. Displays adoption history status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. info {on <DEVICE-NAME>} Displays adopted device details on <DEVICE-NAME> Optional. Displays adoption details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. offline Displays devices non-adopted status and its adopted access points
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 431 Example wm3400-34710C8(config-device-00-15-70-37-FA-BE)#show adoption offline -------------------------------------------------------------------------- MAC HOST-NAME TYPE RF-DOMAIN -------------------------------------------------------------------------- 00-15-70-88-9E-C4 AP4731-889EC4 AP4731 default 11-22-33-44-55-66 AP4600-445566 AP4600 default -------------------------------------------------------------------------- Total number of APs displayed: 2 wm3400-34710C8(config-device-00-15-70-37-FA-BE)# wm3400-34710C8(config-adoption-policy-test)#show adoption info Number of APs adopted : 1 Number of AAPs adopted : 0 Available AP licenses : 49 Available AAP licenses : 50 Device in cluster : No Cluster state : active -------------------------------------------------------------------------- MAC HOST-NAME TYPE VERSION ADOPTED-BY LAST- ADOPTION -------------------------------------------------------------------------- 00-A0-F8-00-00-00 AP4600-000000 AP4600 5.3.0.0-048B 00-15-70-37-FA-BE 2010-08-17 23:48:48 -------------------------------------------------------------------------- Total number of APs displayed: 1 wm3400-34710C8(config-adoption-policy-test)# wm3400-34710C8(config)#show adoption history -------------------------------------------------------------------------- MAC TYPE EVENT REASON TIME-STAMP -------------------------------------------------------------------------- 00-23-68-13-9B-34 AP4731 adopted N.A. 2011-01-01 05:28:14 -------------------------------------------------------------------------- wm3400-34710C8(config)# pending {on <DEVICE-NAME>} Displays details for access points pending adoption, but have to actually connect to wireless controller on <DEVICE-NAME> Optional. Displays information on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. status {on <DEVICE-NAME>} Displays a devices adoption status on <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 432 advanced-wips show commands Displays advanced Wireless Intrusion Prevention Policy (WIPS) settings Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show advanced-wips [configuration|stats] show advanced-wips configuration [events {thresholds}|terminate-list] show advanced-wips stats [ap-table|client-table|connected-sensors| event-history|server-listening-port] show advanced-wips stats [detected-aps|detected-clients-for AP <MAC>] {[neighboring|sanstioned|unsanctioned]} Parameters show advanced-wips configuration [events {thresholds}|terminate-list] show advanced-wips stats [ap-table|client-table|connected-sensors|event- history|server-listening-port] configuration Displays advanced WIPS settings events thresholds Displays events summary Advanced WIPS policies are assigned to wireless controllers and support various events depending on the configuration. These events are individually triggered against authorized, unauthorized, and neighboring devices. thresholds Optional. Displays threshold values for each event configured in the advanced WIPS policy terminate-list Displays the terminate list stats Displays advanced WIPS statistics ap-table Displays AP table statistics client-table Displays station table statistics connected-sensors Displays connected sensors statistics
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 433 show advanced-wips stats [detected-aps|detected-clients-for AP <MAC>] {[neighboring|sanstioned|unsanctioned]} Example wm3400-34710C8(config)#show advanced-wips configuration events +------+----+---------------------------------------------+----------+---- |POLICY|SLNO|NAME|AUTHORIZED|UNAUTHORIZED|NEIGHBORING| +------+----+---------------------------------------------+----------+---- Trigger-S: Trigger against Sanctioned devices enabled(Y)/disabled(N) Trigger-U: Trigger against Unsanctioned devices enabled(Y)/disabled(N) Trigger-N: Trigger against Neighboring devices enabled(Y)/disabled(N) | - | - | - | +------+----+---------------------------------------------+----------+---- wm3400-34710C8(config)# wm3400-34710C8(config)#show advanced-wips configuration events thresholds +--------+-----+--------------------------+--------------------------+---- | POLICY | # | EVENT | THRESHOLD | VALUE | +--------+-----+--------------------------+--------------------------+---- | test | 1 | dos-eapol-logoff-storm | eapol-start-frames-ap | 9 | | test | 2 | dos-eapol-logoff-storm | eapol-start-frames-mu | 99 | | test | 3 | dos-cts-flood | cts-frames-ratio | 8 | | test | 4 | dos-cts-flood | mu-rx-cts-frames | 20 | +--------+-----+--------------------------+--------------------------+---- wm3400-34710C8(config)# wm3400-34710C8(config)#show advanced-wips stats detected-stations-for-ap 11-22-33-44-55-66 authorized Number of stations associated to the AP 11-22-33-44-55-66: 0 event-history Displays advanced WIPS event history server-listening-port Displays advanced WIPS server listening port statistics stats Displays advanced WIPS statistics detected-aps {neighboring|sanctioned|uns anctioned} Displays AP details based on the parameters passed neighboring Optional. Displays neighboring AP statistics sanctioned Optional. Displays sanctioned AP statistics unsanctioned Optional. Displays unsanctioned AP statistics detected-clients-for-ap <MAC> {neighboring|sanctioned| unsanctioned} Displays clients statistics for APs <MAC> Displays clients for a specified AP. Enter the MAC address (BSS- ID) of the AP. neighboring Optional. Displays neighboring client information sanctioned Optional. Displays sanctioned client information unsanctioned Optional. Displays unsanctioned client information
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 434 wm3400-34710C8(config)# wm3400-34710C8(config)#show advanced-wips stats client-table Number of clients: 2 wm3400-34710C8(config)# wm3400-34710C8(config)#show advanced-wips configuration events thresholds -------------------------------------------------------------------------- POLICY # EVENT THRESHOLD VALUE -------------------------------------------------------------------------- test 1 probe-response-flood probe-rsp-frames-count 50 test 2 dos-cts-flood cts-frames-ratio 70 test 3 dos-cts-flood mu-rx-cts-frames 20 test 4 dos-eapol-logoff-storm eapol-start-frames-ap 10 ------------------------------------------------------------------------ wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 435 ap-upgrade show commands Displays AP firmware image upgrade information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show ap-upgrade [history {on <RF-DOMAIN-NAME>}|load-image-status|status {on [<RF-DOMAIN-NAME>|<RF-DOMAIN-MANAGER>]}|versions {on <RF-DOMAIN- MANAGER>}] Parameters show ap-upgrade [history {on <RF-DOMAIN-NAME>}|load-image-status|status {on [<RF-DOMAIN-NAME>|<RF-DOMAIN-MANAGER>]|versions {<RF-DOMAIN-MANAGER>}] Example wm3400-34710C8(config)#show ap-upgrade history ap-upgrade Displays AP firmware upgrade details history {on <RF-DOMAIN-NAME>} Displays AP firmware upgrade history (AP address, upgrade result, time of upgrade, number of retries, upgrade by etc.) on <RF-DOMAIN-NAME> Optional. Displays device firmware upgrade history in a RF Domain <RF-DOMAIN-NAME> Specify the RF Domain name. load-image-status Displays firmware image download status on a device status on {<RF-DOMAIN-NAME>| <RF-DOMAIN-MANAGER>} Displays AP firmware upgrade status on Optional. Displays firmware upgrade status on a RF Domain or RF Domain manager <RF-DOMAIN-NAME> Optional. Specify the RF Domain name. <RF-DOMAIN MANAGER> Optional. Specify the RF Domain manager name. versions {on <RF-DOMAIN- MANAGER>} Displays upgrade image versions on <RF-DOMAIN-MANAGER> Optional. Displays upgrade image versions on devices adopted by a RF Domain manager
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 436 --------------------------------------------------------------------------- --------- AP RESULT TIME RETRIES UPGRADED-BY LAST-UPDATE-ERROR --------------------------------------------------------------------------- --------- 00-04-96-44-54-C0 done 2011-03-31 02:06:39 0 00-04-96-42-14-79 - 00-04-96-44-54-C0 done 2011-04-14 00:46:52 0 00-04-96-42-14-79 - 00-04-96-44-54-C0 done 2011-04-25 00:12:00 0 00-04-96-42-14-79 - 00-04-96-44-54-C0 done 2011-04-28 07:17:38 0 00-04-96-42-14-79 - 00-04-96-44-54-C0 done 2011-05-04 12:15:31 0 00-04-96-42-14-79 - Total number of entries displayed: 5
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 437 boot show commands Displays a devices boot configuration. Use the on command to view a remote devices boot configuration. NOTE This command is not present in the USER EXEC Mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show boot {on <DEVICE-NAME>} Parameters show boot {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show boot on wm3400-34710C8 -------------------------------------------------------------------------- IMAGE BUILD DATE INSTALL DATE VERSION -------------------------------------------------------------------------- Primary 2011-05-10 09:58:17 2010-02-07 10:33:55 5.3.0.0- 026D Secondary 2011-06-10 21:29:31 2011-06-15 14:21:17 5.3.0.0- 033D -------------------------------------------------------------------------- Current Boot : Secondary Next Boot : Secondary boot Displays primary and secondary image boot configuration details (build date, install date, version, and the image used to boot the current session) on <DEVICE-NAME> Optional. Displays boot configuration information on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 438 Software Fallback : Enabled wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 439 captive-portal show commands Displays WLAN hotspot information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show captive-portal client {filter|on} show captive-portal client {filter [captive-portal|ip|state|vlan|wlan]} show captive-portal client {filter captive-portal [<CAPTIVE-PORTAL>| not <CAPTIVE-PORTAL>]}] show captive-portal client {filter ip [<IP>|not <IP>]} show captive-portal client {filter state [not[pending|success] |pending|success]} show captive-portal client {filter vlan [<VLAN>|not <VLAN>]} show captive-portal client {filter wlan [<WLAN>|not <WLAN>]} show captive-portal client {on <DEVICE-OR-DOMAIN-NAME> {filter {captive- portal| ip|state|vlan|wlan}} Parameters show captive-portal client {filter captive-portal [<CAPTIVE-PORTAL>| not <CAPTIVE-PORTAL>]} show captive-portal client {filter ip [<IP>|not <IP>]} captive-portal client Displays captive portal client information filter Optional. Defines additional filters captive-portal [<CAPTIVE-PORTAL>| not <CAPTIVE-PORTAL>] Optional. Displays a specified captive portal client information <CAPTIVE-PORTAL> Specify the captive portal name. not <CAPTIVE-PORTAL> Inverts the match selection captive-portal client Displays captive portal client information filter Optional. Defines additional filters
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 440 show captive-portal client {filter state [not [pending|success]| pending|success]} show captive-portal client {filter vlan [<VALN-ID>|not <VLAN-ID>]} show captive-portal client {filter wlan [<WALN-ID>|not <WLAN-ID>]} show captive-portal client {on <DEVICE-OR-DMAIN-NAME> filter [captive- portal|ip|state|vlan|wlan]} ip [<IP>|not <IP>] Displays captive portal client information based on the IP address passed <IP> Specify the IP address. not <IP> Inverts the match selection captive-portal client Displays captive portal client information filter Optional. Defines additional filters state not [pending|success]] Optional. Filters clients based on their authentication state not Inverts match selection pending Displays clients successfully authenticated (Opposite of pending authentication) success Displays clients redirected for authentication (Opposite of successful authentication) state [pending|success]] Optional. Filters clients based on their authentication state pending Displays clients redirected for authentication success Displays clients successfully authenticated captive-portal client Displays captive portal client information filter Optional. Defines additional filters vlan [<VLAN>| not <VLAN>] Optional. Displays clients on a specified VLAN <VLAN> Specify the VLAN ID. not <VLAN> Inverts match selection captive-portal client Displays captive portal client information filter Optional. Defines additional filters wlan [<WLAN>| not <WLAN>] Optional. Displays clients on a specified WLAN <WLAN> Specify the WLAN ID. not <WLAN> Inverts match selection captive-portal client Displays captive portal client information on <DEVICE-OR-DOMAIN- NAME> Optional. Displays captive portal clients on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 441 Example wm3400-34710C8(config)#show captive-portal client on WM3700-421479 --------------------------------------------------------------------------- --------- CLIENT IP CAPTIVE-PORTAL WLAN VLAN STATE SESSION TIME --------------------------------------------------------------------------- --------- --------------------------------------------------------------------------- --------- Total number of captive portal clients displayed: 0 filter Optional. Defines additional filters captive-portal Optional. Displays client information for a specified captive portal ip Optional. Displays captive portal client information based on the IP address passed state Optional. Displays client information based on the their authentication state vlan Displays clients on a specified VLAN wlan Optional. Displays clients on a specified WLAN
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 442 cdp show commands Displays the Cisco Discovery Protocol (CDP) neighbor table Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show cdp [neighbors|report] {detail {on <DEVICE-OR-DOMAIN-NAME>}| on <DEVICE-OR-DOMAIN-NAME>} Parameters show cdp [neighbors|report] {detail {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE-OR-DOMAIN-NAME>} Example The following example displays CDP neighbors table in detail. wm3400-34710C8(config)#show cdp neighbors detail on wm3400-34710C8 ------------------------- Device ID: WM3400-229D58 Entry address(es): IP Address: 172.16.10.6 IP Address: 169.254.157.88 Platform: WM-3400-00010-WR, Capabilites: Router Switch cdp [neighbors|report] Displays CDP neighbors table or aggregated CDP neighbors table detail {on <DEVICE-OR- DOMAIN-NAME>} Optional. Displays CDP neighbors table or aggregated CDP neighbors table details on <DEVICE-OR-DOMAIN-NAME> Optional. Displays table details on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. on <DEVICE-OR- DOMAIN-NAME> Optional. Displays table details on a specified device or domain (This option does not display detailed information) <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 443 Interface: ge1, Port ID (outgoing port): ge1 Hold Time: 173 sec advertisement version: 2 Native VLAN: 1 Duplex: full Version : 5.3.0.0-048B ------------------------- Device ID: wm3600-380649 Entry address(es): IP Address: 2.2.2.2 IP Address: 172.16.10.4 Platform: WM3600, Capabilites: Router Switch Interface: ge1, Port ID (outgoing port): ge1 Hold Time: 173 sec advertisement version: 2 --More-- wm3400-34710C8(config)# The following example shows a non-detailed CDP neighbors table. wm3400-34710C8(config)#show cdp neighbors on wm3400-34710C8 -------------------------------------------------------------------------- Device ID Neighbor IP Platform Local Intrfce Port ID Duplex -------------------------------------------------------------------------- wm3400-229D58 172.16.10.6 WM-3411-00010-WR ge1 ge1 full wm3600-380649 2.2.2.2 WM3600 ge1 ge1 full -------------------------------------------------------------------------- wm3400-34710C8(config)# wm3400-34710C8(config)#show cdp neighbors on wm3400-34710C8 --------------------------------------------------------------------------- ----- Device ID Neighbor IP Platform Local Intrfce Port ID Duplex --------------------------------------------------------------------------- ----- ap4600-4454C0 169.254.84.192 AP4610-ROW ge8 ge1 full --------------------------------------------------------------------------- -----
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 444 clock show commands Displays a systems clock Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show clock {on <DEVICE-NAME>} Parameters show clock {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show clock 2011-06-21 14:14:49 IST wm3400-34710C8(config)# clock Displays a systems clock on <DEVICE-NAME> Optional. Displays system clock on a specified device <DEVICE-NAME> Specify the name of the AP, wireless controller, or RF Domain.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 445 cluster show commands Displays cluster information (cluster configuration parameters, members, status etc.) Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show cluster [configuration|members {detail}|status] Parameters show cluster [configuration|members {detail}|status] Example wm3400-34710C8(config)#show cluster configuration Cluster Configuration Information Mode : Active Number of peer(s) : 0 Auto revert : Disabled Auto revert interval (Mins) : 5 Controller AP license : 0 Controller AAP license : 0 Controller max AP adoption capacity : 1024 Cluster Runtime Information Cluster protocol version : 1 Cluster run state : active Cluster AP license : 0 Cluster AAP license : 0 Controller AP count : 0 cluster Displays cluster information configuration Displays cluster configuration parameters members {detail} Displays cluster members configured on the logged device detail Optional. Displays detailed information of known cluster members status Displays cluster status
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 446 Controller AAP count : 0 Cluster AP count : 0 Cluster AAP count : 0 Cluster max AP adoption capacity : 1024 Number of connected peer(s) : 0 wm3400-34710C8(config)#show cluster members detail +-------------+-------------------+--------+--------+---------+----------| ID | MAC | MODE |AP COUNT|AAP COUNT|AP LICENSE|AAP LICENSE| VERSION | +-------------+-------------------+--------+--------+---------+----------| 70.37.fa.be | 00-15-70-37-FA-BE | Active | 0 | 0 | 0 | 0 | Unknown | +-------------+-------------------+--------+--------+---------+----------+
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 447 commands show commands Displays commands available for the current mode Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show commands Parameters None Example wm3400-34710C8(config)#show commands help help search WORD (|detailed|only-show|skip-show) show commands show debugging (|(on DEVICE-OR-DOMAIN-NAME)) show debugging cfgd show debugging wireless (|(on DEVICE-OR-DOMAIN-NAME)) show debugging voice (|(on DEVICE-OR-DOMAIN-NAME)) show debugging captive-portal (|(on DEVICE-OR-DOMAIN-NAME)) show debugging dhcpsvr (|(on DEVICE-NAME)) show debugging mstp (|(on DEVICE-OR-DOMAIN-NAME)) show debugging advanced-wips show debugging vpn (|(on DEVICE-NAME)) show debugging radius (|(on DEVICE-NAME)) show (running-config|session-config) (|include-factory) show running-config interface (|`WORD|ge <1-4>|me1|pc <1-4>|vlan <1- 4094>') (|include-factory) show running-config wlan WLAN (|include-factory) show (running-config) device (self|DEVICE-NAME) (|include-factory) show session-changes show startup-config (|include-factory) show adoption info (|(on DEVICE-NAME))
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 448 show adoption offline show licenses show password-encryption status show debug xpath get WORD (|WORD) show debug xpath count WORD show debug xpath list WORD show rf-domain-manager show timezone show event-history show ntp status show ntp associations (|detail) show device-categorization summary show wireless ap (|(on DEVICE-OR-DOMAIN-NAME)) show wireless ap configured show wireless ap detail (|WORD) show wireless unsanctioned aps (|(on DEVICE-OR-DOMAIN-NAME)) show wireless unsanctioned aps detailed (|(on DEVICE-OR-DOMAIN-NAME)) show wireless unsanctioned aps statistics (|(on DEVICE-OR-DOMAIN-NAME)) show wireless client (|(on DEVICE-OR-DOMAIN-NAME)) (|(filter {|(state (|not) (data-ready|roaming))|(wlan (|not) WLAN)|(ip (|not) A.B.C.D)})) show wireless client detail AA-BB-CC-DD-EE-FF (|(on DEVICE-OR-DOMAIN- NAME)) show wireless client statistics (|traffic) (|(on DEVICE-OR-DOMAIN-NAME)) show wireless client statistics rf (|(on DEVICE-OR-DOMAIN-NAME)) ............................................... wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 449 context show commands Displays the current context details Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show context {include-factory|session-config {include-factory}} Parameters show context {include-factory|session-config {include-factory}} Example wm3400-34710C8>show context include-factory ! ! Configuration of WM3700 version 5.3.0.0-048B ! ! version 2.1 ! ! firewall-policy default ip dos smurf log-and-drop log-level warnings ip dos twinge log-and-drop log-level warnings ip dos invalid-protocol log-and-drop log-level warnings ip dos router-advt log-and-drop log-level warnings ip dos router-solicit log-and-drop log-level warnings ip dos option-route log-and-drop log-level warnings ip dos ascend log-and-drop log-level warnings ip dos chargen log-and-drop log-level warnings ip dos fraggle log-and-drop log-level warnings include-factory Optional. Includes factory defaults session-config include-factory Optional. Displays running system information in the current context include-factory Optional. Includes factory defaults
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 450 ip dos snork log-and-drop log-level warnings ip dos ftp-bounce log-and-drop log-level warnings ip dos tcp-intercept log-and-drop log-level warnings ip dos broadcast-multicast-icmp log-and-drop log-level warnings ip dos land log-and-drop log-level warnings ip dos tcp-xmas-scan log-and-drop log-level warnings --More-- wm3400-34710C8>
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 451 critical-resources show commands Displays critical resource information. Critical resources are resources vital to the wireless controller managed network. Some critical resources are security spanning routers, switches, firewalls, VPNs, VLANs, WiFi access points etc. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show critical-resources {on <DEVICE-NAME>} Parameters show critical-resources {on <DEVICE-NAME>} Example WM3400-22CDAA(config)#sh critical-resources on WM3400-22CDAA -------------------------------------------------------------------------- CRITICAL RESOURCE IP VLAN PING-MODE STATE -------------------------------------------------------------------------- 172.168.1.103 1 arp-icmp up critical-resources Displays critical resource information on <DEVICE-NAME> Optional. Displays critical resource information on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 452 crypto show commands Displays encryption mode information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show crypto [ipsec|isakmp|key|pki] show crypto [ipsec|isakmp] sa {on <DEVICE-NAME>} show crypto key rsa {on <DEVICE-NAME>|public-key-detail {on <DEVICE- NAME>} show crypto pki trustpoints {<TRUSTPOINT> {on <DEVICE-NAME>}| all {on <DEVICE-NAME>}|on <DEVICE-NAME>} Parameters show crypto [ipsec|isakmp] sa {on <DEVICE-NAME>} show crypto key rsa {on <DEVICE-NAME>|public-key-detail {on <DEVICE-NAME>}} crypto [ipsec|isakmp] sa Displays encryption information ipsec Displays Internet Protocol Security (IPSec) statistics. The IPSec encryption authenticates and encrypts each IP packet in a communication session. isakmp Displays Internet Security Association and Key Management Protocol (ISAKMP) statistics. The ISAKMP protocol provides a means of authentication and key exchange. The following is common to the IPSec and ISAKMP parameters: sa Displays all IPSec or ISAKMP Security Associations (SA) on <DEVICE-NAME> Optional. Displays IPSec or ISAKMP SAs on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. crypto key Displays key management operations
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 453 show crypto pki trustpoints {<TRUSTPOINT> {on <DEVICE-NAME>}|all {on <DEVICE-NAME>}|on <DEVICE-NAME>} Example wm3400-34710C8(config)#show crypto key rsa public-key-detail on wm3400- 34710C8 RSA key name: default-trustpoint-srvr-priv-key Key-length: 1024 -----BEGIN PUBLIC KEY----- MIGfMA0GCSqGSIb3DQEBAQUAA4GNADCBiQKBgQDGHBR2bxLeRZ4G6hm7jHJRSaeE A216r4s4qptiSld+rKeMiHPtFbyELedk3dITkzF1EU7Ov0vKzant0pyAmdJ8ci// wSQMmZjX3RwF9OFBRp2C09LFj?1VX2fsoD6xXhJHBLieJ9qzF+ZQ2CYG7+r29P/o 3rfr/GLaTN3C6RIWvQIDAQAB -----END PUBLIC KEY----- RSA key name: default_rsa_key Key-length: 1024 -----BEGIN PUBLIC KEY----- MIGdMA0GCSqGSIb3DQEBAQUAA4GLADCBhwKBgQCwXXWGE9j/i3EiSjnY9x1Ktsbt rzgqB1KhlShWIgnWqlxjzvO6S?GmBPG5XqBS3rKqIzrgh6fXF2cNJZweWgc1QktL AoZN/MeCiGVGiJZmtmyKlHPMgyyLGqm6krvWFfOdqlA85+WdQyvDsevTVVp/OiEB al4SsIvMG+U/UQaI1wIBIw== -----END PUBLIC KEY----- wm3400-34710C8(config)# wm3400-34710C8(config)#show crypto key rsa on wm3400-34710C8 +------------+-------------------------------------------+---------------- rsa {on <DEVICE-NAME>} Displays RSA public keys on <DEVICE-NAME> Optional. Displays RSA public keys on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. public-key-detail {on <DEVICE-NAME>} Displays public key in the Privacy Enhanced Mail (PEM) format on <DEVICE-NAME> Optional. Displays public key on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. crypto pki Displays Public Key Infrastructure (PKI) commands trustpoints Displays WLAN trustpoints <TRUSTPOINT> {on <DEVICE-NAME>} Optional. Displays a specified trustpoint. Specify the trustpoint name. on <DEVICE-NAME> Optional. Displays trustpoint details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. all {on <DEVICE-NAME>} Optional. Displays all trustpoints on <DEVICE-NAME> Optional. Displays all trustpoints configured on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Displays trustpoints configured on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 454 | # | KEY NAME | KEY LENGTH | +------------+-------------------------------------------+---------------- | 1 | default-trustpoint-srvr-priv-key | 1024 | | 2 | default_rsa_key | 1024 | +------------+-------------------------------------------+----------------- ----+ wm3400-34710C8(config)# wm3400-34710C8config)#show crypto pki trustpoints all on wm3400-34710C8 Trustpoint Name: default-trustpoint (self signed) -------------------------------------------------------------------------- CRL present: no Server Certificate details: Key used: default-trustpoint-srvr-priv-key Serial Number: 0671 Subject Name: C=US, ST=CA, L=San Jose, O=Enterprise Mobility, OU=EWLAN, CN=Extreme Networks Issuer Name: C=US, ST=CA, L=San Jose, O=Enterprise Mobility, OU=EWLAN, CN=Extreme Networks Valid From : Tue Sep 22 16:19:51 2009 UTC Valid Until: Wed Sep 22 16:19:51 2010 UTC wm3400-34710C8(config)# wm3400-34710C8(config)#show crypto pki trustpoints all Trustpoint Name: default-trustpoint (self signed) -------------------------------------------------------------------------- CRL present: no Server Certificate details: Key used: default-trustpoint-srvr-priv-key Serial Number: 0671 Subject Name: C=US, ST=CA, L=San Jose, O=Enterprise Mobility, OU=EWLAN, CN=Extreme Networks Issuer Name: C=US, ST=CA, L=San Jose, O=Enterprise Mobility, OU=EWLAN, CN=Extreme Networks Valid From : Tue Sep 22 16:19:51 2009 UTC Valid Until: Wed Sep 22 16:19:51 2010 UTC wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 455 debug show commands Displays debugging status of the DPD2 module, profile functions, and XPath operations Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show debug [dpd2|profile|xpath] show debug dpd2 {on <DEVICE-NAME>} show debug profile <WORD> {arg <WORD>} show debug xpath [count|get|list] show debug xpath [count|list] <WORD> show debug xpath get <WORD> {option|param <WORD> option} [do-profiling| no-pretty|show-tail-only|use-generator|use-streaming] Parameters show debug dpd2 {on <DEVICE-NAME>} show debug profile <WORD> {arg <WORD>} debug dpd2 Displays DPD2 module debugging status on <DEVICE-NAME> Optional. Displays the debugging status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. debug profile <WORD> {arg <WORD>} Displays profile function debugging status <WORD> Specify the name of the profile function. arg <WORD> Optional. Specify arguments for the function in a single word, separated by a coma (for example. cli,[3,4]).
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 456 show debug xpath [count|list] <WORD> show debug xpath get <WORD> {option|param <WORD> option} [do-profiling| no-pretty|show-tail-only|use-generator|use-streaming] Example wm3400-34710C8(config)#show debug xpath count /wing-stats Success: 4 wm3400-34710C8(config)# wm3400-34710C8(config)#show debug xpath get word option do-profiling no- pretty Wed Jun 22 09:28:34 2011 /var/profile 26 function calls in 0.001 CPU seconds Ordered by: standard name ncalls tottime percall cumtime percall filename:lineno(function) debug xpath Displays XPath-based operation debugging status count <WORD> Prints the number of items under an XPath node <WORD> Specify the XPath node. (for example, /wing-stats/device/self/ interface) list <WORD> Lists the names (keys) under an XPath node <WORD> Specify the XPath node. (for example, /wing-stats/device/self/ interface) debug xpath Displays XPath-based operation debugging status get <WORD> Prints the XPath node value based on the options passed <WORD> Specify the XPath node. (for example, /wing-stats/device/self/ interface) option Optional. Prints the XPath node value based on the options passed Select one of the following options: do-profiling Performs profiling no-pretty Disables pretty for speed show-tail-only Displays only the tail of the result use-generator Performs streaming using generator interface use-streaming Uses streaming interface param <WORD> option Optional. Prints the XPath node value based on the options passed <WORD> Specify the parameter in the dictionary format (for example, rf_domain_name:a_name,dummy_name:dummy_value) option After entering the parameter, select one of the following options: do-profiling Performs profiling no-pretty Disables pretty for speed show-tail-only Displays only the tail of the result use-generator Performs streaming using generator interface use-streaming Uses streaming interface
TM 4000 Series Access Point CLI Reference Guide 458 debugging show commands Displays debugging information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show debugging {advanced-wips|captive-portal|cfgd|dhcpsvr|mint|mstp| nsm|on|radius|snmp|voice|vpn|wireless} show debugging {[advanced-wips|cfgd]} show debugging {[captive-portal|mint|mstp|nsm|voice|wireless]} {on <DEVICE-OR-DOMAIN-NAME>} show debugging {on <DEVICE-OR-DOMAIN-NAME>} show debugging {dhcpsvr|radius|snmp|vpn} {on <DEVICE-NAME>} Parameters show debugging {advanced-wips|cfgd} show debugging {captive-portal|mint|mstp|nsm|voice|wireless} {on <DEVICE- OR-DOMAIN-NAME>} debugging {advanced-wips|cfgd} Displays debugging processes in progress based on the parameters passed advanced-wips Optional. Displays the advanced WIPS modules debugging configuration cfgd Optional. Displays the cfgd process debugging configuration debugging {captive-portal| mint|mstp|nsm|voice| wireless} Displays debugging processes in progress based on the parameters passed captive-portal Optional. Displays the hotspot (HSD) modules debugging configuration mint Optional. Displays the MiNT modules debugging configuration mstp Optional. Displays the Multiple Spanning Tree (MST) modules debugging configuration nsm Optional. Displays Network Service Module (NSM) debugging configuration voice Optional. Displays the voice modules debugging configuration wireless Optional. Displays the wireless modules debugging configuration
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 459 show debugging {dhcpsvr|radius|snmp|vpn} {on <DEVICE-NAME>} show debugging {on <DEVICE-OR-DOMAIN-NAME>} Example wm3400-34710C8(config)#show debugging cfgd cfgd: config debugging is on cluster debugging is on wm3400-34710C8(config)# on <DEVICE-OR-DOMAIN- NAME> The following are common to all of the above options: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays debugging processes on a device or RF Domain. <DEVICE-OR-DOMAIN-NAME> The name of the AP, wireless controller, or RF Domain. debugging {dhcpsvr|radius|snmp| vpn} Displays debugging processes in progress based on the parameters passed dhcpsvr Optional. Displays the DHCP server configuration modules debugging information radius Optional. Displays the RADIUS server configuration modules debugging information snmp Optional. Displays the Simple Network Management Protocol (SNMP) modules debugging information vpn Optional. Displays the VPN modules debugging information snmp Optional. Displays the SNMP modules debugging information on <DEVICE-NAME> The following are common to all of the above options: on <DEVICE-NAME> Optional. Displays debugging processes on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. debugging {on <DEVICE- OR-DMAIN-NAME>} Displays all debugging processes in progress on a specified device or RF Domain. on <DEVICE-OR-DOMAIN-NAME> Optional. Displays debugging processes in progress, on a device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 460 device-categorization show commands Displays device categorization summary Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show device-categorization summary Parameters show device-categorization summary Example wm3400-34710C8(config)#show device-categorization summary -------------------------------------------------------------------------- POLICY # A/N AP/CLIENT MAC SSID -------------------------------------------------------------------------- DEVICE-CATEGORIZATION 1 sanctioned client 00-40-96-B0-BA-2D - DEVICE-CATEGORIZATION 2 neighboring client 00-40-96-B0-BA-2A - DEVICE-CATEGORIZATION 3 sanctioned ap 00-23-68-31-12-65 ASDF -------------------------------------------------------------------------- wm3400-34710C8(config)# device-categorization summary Displays device categorization summary
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 461 event-history show commands Displays event history report Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show event-history {on <DEVICE-OR-DOMAIN-NAME>} Parameters show event-history {on <DEVICE-OR-DOMAIN-NAME>} Example wm3400-34710C8(config)#show event-history EVENT HISTORY REPORT Generated on '2011-06-22 12:50:10 IST' by 'admin' 2011-06-22 10:28:22 00-15-70-37-FA-BE SYSTEM LOGIN Successfully logged in User: 'admin' with privilege 'superuser' from 'ssh' 2011-06-22 10:25:01 00-15-70-37-FA-BE SYSTEM LOGOUT Logged out User: 'admin' with privilege 'superuser' from '172.16.10.10' 2011-06-22 09:39:35 00-15-70-37-FA-BE NSM IFUP Interface ge3 is up 2011-06-22 09:39:34 00-15-70-37-FA-BE NSM IFUP Interface ge3 is up 2011-06-22 09:37:16 00-15-70-37-FA-BE NSM IFDOWN Interface ge3 is down 2011-06-22 07:24:21 00-15-70-37-FA-BE SYSTEM LOGIN Successfully logged in User: 'admin' with privilege 'superuser' from 'ssh' event-history Displays event history report on <DEVICE-OR-DOMAIN- NAME> Optional. Displays event history report on a device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 462 2011-06-22 07:01:54 00-15-70-37-FA-BE NSM IFUP Interface ge3 is up 2011-06-22 07:01:53 00-15-70-37-FA-BE NSM IFUP Interface ge3 is up 2011-06-22 07:01:35 00-15-70-37-FA-BE NSM IFDOWN Interface ge3 is down 2011-06-22 07:01:18 00-15-70-37-FA-BE NSM IFUP Interface ge3 is up --More-- wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 463 event-system-policy show commands Displays detailed event system policy configuration Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show event-system-policy [config|detail] <EVENT-SYSTEM-POLICY> Parameters show event-system-policy [config|detail] <EVENT-SYSTEM-POLICY> Example wm3400-34710C8(config)#show event-system-policy config testpolicy -------------------------------------------------------------------------- MODULE EVENT SYSLOG SNMP FORWARD EMAIL -------------------------------------------------------------------------- aaa radius-discon-msg on on on default -------------------------------------------------------------------------- wm3400-34710C8(config)# wm3400-34710C8 event-system-policy Displays event system policy configuration config Displays configuration for a specified policy detail Displays detailed configuration for a specified policy <EVENT-SYSTEM- POLICY> Specify the event system policy name.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 464 file show commands Displays file system information NOTE This command is not available in the USER EXEC Mode. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show file [information <FILE>|systems] Parameters show file [information <FILE>|systems] Example wm3400-34710C8(config)#show file systems File Systems: Size(b) Free(b) Type Prefix - - opaque system: 10485760 9916416 flash nvram: 20971520 20131840 flash flash: - - network (null) - - network rdp: - - network sftp: - - network http: - - network ftp: - - network tftp: information <FILE> Displays file information <FILE> Specify the file name. systems Lists all file systems present in the system
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 465 20971520 20131840 - hotspot: wm3400-34710C8(config)# wm3400-34710C8(config)#show file information flash flash:: type is directory wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 466 firewall show commands Displays wireless firewall information, such as DHCP snoop table entries, denial of service statistics, active session summaries etc. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show firewall [dhcp|dos|flows] show firewall [dhcp snoop-table|dos stats] {on <DEVICE-NAME>}] show firewall flows {[filter|management|on|stats|wireless-client <MAC>]} show firewall flows {filter [dir|dst port <1-65535>|ether|flow-type|icmp| igmp|ip|max-idle|min-bytes|min-idle|min-pkts|not|port|src|tcp|udp]} show firewall flows {management {on <DEVICE-NAME>}|stats {on <DEVICE- NAME>}|wireless-client <MAC>|on <DEVICE-NAME>} Parameters show firewall [dhcp snoop-table|dos stats] dhcp snoop-table Displays Dynamic Host Configuration Protocol (DHCP) snoop table entries snoop-table Displays DHCP snoop table entries DHCP snooping acts as a firewall between non-trusted hosts and the DHCP server. Snoop table entries contain MAC address, IP address, lease time, binding type, and interface information of non-trusted interfaces. dos stats Displays Denial of Service (DoS) statistics on <DEVICE-NAME> The following are common to the DHCP snoop table and DoS stats parameters: on <DEVICE-NAME> Optional. Displays snoop table entries, or DoS stats on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 467 show firewall flows {management {on <DEVICE-NAME>}|stats {on <DEVICE- NAME>}|wireless-client <MAC>|on <DEVICE-NAME>} show firewall flows filter [(dir|dst|ether|flow-type|icmp|igmp|ip| max-idle|min-bytes|min-idle|min-pkts|not|port|src|tcp|udp)] {(dir|dst|ether| flow-type|ip|max-idle|min-bytes|min-idle|min-pkts|port|src)} firewall flows Notifies a session has been established management {on <DEVICE-NAME>} Optional. Displays management traffic firewall flows on <DEVICE-NAME> Optional. Displays firewall flows on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. stats {on <DEVICE-NAME>} Optional. Displays active session summary on <DEVICE-NAME> Optional. Displays active session summary on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. wireless-client <MAC> Optional. Displays wireless clients firewall flows <MAC> Specify the MAC address of the wireless client. on <DEVICE-NAME> Optional. Displays all firewall flows on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. firewall filter Defines additional firewall flow filter parameters dir [wired-wired|wired- wireless|wireless- wired|wireless-wireless] Matches the packet flow direction wired-wired Wired to wired flows wired-wireless Wired to wireless flows wireless-wired Wireless to wired flows wireless-wireless Wireless to wireless flows dst <PORT> <1-65535> Matches the destination port with the specified port <PORT> Specifies the destination port <1-65535> Specify the destination port number from 1 - 65535. ether [dst <MAC>|host <MAC>| src|vlan] Displays Ethernet filter options dst <MAC> Matches the destination MAC address host <MAC> Matches flows containing the specified MAC address src <MAC> Matches only the source MAC address vlan <1-4094> Matches the VLAN number of the traffic with the specified value. Specify a value from 1- 4094. flow-type [bridged|natted|routed| wired|wireless] Matches the traffic flow type bridged Bridged flows natted Natted flows routed Routed flows wired Flows belonging to wired hosts wireless Flows containing a mobile unit icmp {code|type} Matches flows with the specified Internet Control Message Protocol (ICMP) code and type code Matches flows with the specified ICMP code type Matches flows with the specified ICMP type
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 468 Example wm3400-34710C8(config)#show firewall dhcp snoop-table on wm3400-34710C8 Snoop Binding <157.235.208.252, 00-15-70-37-FA-BE, Vlan 4> Type Controller-SVI, Touched 32 seconds ago -------------------------------------------------------------------------- Snoop Binding <172.16.10.2, 00-15-70-37-FA-BE, Vlan 1> Type Controller-SVI, Touched 1 seconds ago -------------------------------------------------------------------------- wm3400-34710C8(config)# wm3400-34710C8(config)#show firewall flows management on wm3400-34710C8 ========== Flow# 1 Summary ========== Forward: Vlan 1, TCP 172.16.10.10 port 3995 > 172.16.10.1 port 22 00-02-B3-28-D1-55 > 00-15-70-37-FA-BE, ingress port ge1 Egress port: <local>, Egress interface: vlan1, Next hop: <local> (00-15- 70-37-FA-BE) 573 packets, 49202 bytes, last packet 0 seconds ago Reverse: Vlan 1, TCP 172.16.10.1 port 22 > 172.16.10.10 port 3995 00-15-70-37-FA-BE > 00-02-B3-28-D1-55, ingress port local Egress port: ge1, Egress interface: vlan1, Next hop: 172.16.10.10 (00-02- B3-28-D1-55) 552 packets, 63541 bytes, last packet 0 seconds ago TCP state: Established Flow times out in 1 hour 30 minutes wm3400-34710C8(config)# igmp Matches Internet Group Management Protocol (IGMP) flows ip [dst <IPv4>|host <IPv4>|proto <0-254>| src <IPv4>] Filters firewall flows based on the IPv4 parameters passed dst <IPv4> Matches destination IP address host <IPv4> Matches flows containing IPv4 address proto <0-254> Matches the IPv4 protocol src <IPv4> Matches source IP address max-idle Filters firewall flows idle for at least the specified duration. Specify a max-idle value from 1 - 4294967295 bytes. min-bytes Filters firewall flows seen at least the specified number of bytes. Specify a min- bytes value from 1 - 4294967295 bytes. min-idle Filters firewall flows idle for at least the specified duration. Specify a min-idle value from 1 - 4294967295 bytes. min-pkts Filters firewall flows with at least the given number of packets. Specify a min- bytes value from 1 - 4294967295 bytes. not Negates the filter expression selected port <1-65535> Matches either the source or destination port. Specify a port from 1 - 65535. src <1-65535> Matches the source port with the specified port. Specify a port from 1 - 65535. tcp Matches TCP flows udp Matches UDP flows
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 469 wm3400-34710C8(config)#show firewall flows stats on wm3400-34710C8 Active Flows 2 TCP flows 1 UDP flows 0 DHCP flows 1 ICMP flows 0 IPsec flows 0 L3/Unknown flows 0 wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 470 interface show commands Displays wireless controller interface status Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show interfaces {<INTERFACE>|brief|counters|ge <1-4>|me1|on| port-channel {<1-2>|switchport|vlan <1-4094>} {on <DEVICE-NAME>} Parameters show interfaces {<INTERFACE>|brief|counters|ge <1-4>|me1|on| port-cahnnel <1-2>|switchport|vlan <1-4094>} {on <DEVICE-NAME>} interfaces Displays wireless controller interface status based on the parameters passed <INTERFACE> {on <DEVICE-NAME>} Displays status of the interface specified by the <INTERFACE> parameter. Specify the interface name. on <DEVICE-NAME> Optional. Displays interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. brief {on <DEVICE-NAME>} Displays a brief summary of the interface status and configuration on <DEVICE-NAME> Optional. Displays a brief summary on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. counters {on <DEVICE-NAME>} Displays interface Tx or Rx counters on <DEVICE-NAME> Optional. Displays interface Tx or Rx counters on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ge <1-4> Displays Gigabit Ethernet interface status and configuration <1-4> Select the Gigabit Ethernet interface index from 1 - 4. me1 {on <DEVICE-NAME>} Displays Fast Ethernet interface status and configuration on <DEVICE-NAME> Optional. Displays Fast Ethernet interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 471 Example wm3400-34710C8(config)#show interface switchport on wm3400-34710C8E -------------------------------------------------------------------------- INTERFACE STATUS MODE VLAN(S) -------------------------------------------------------------------------- ge1 UP access 1 ge2 DOWN access 1 ge3 UP access 1 ge4 DOWN access 1 -------------------------------------------------------------------------- A '*' next to the VLAN ID indicates the native vlan for that trunk port wm3400-34710C8(config)# wm3400-34710C8(config)#show interface vlan 1 Interface vlan1 is UP Hardware-type: vlan, Mode: Layer 3, Address: 00-15-70-37-FA-BE Index: 4, Metric: 1, MTU: 1500 IP-Address: 172.16.10.1/24 input packets 587971, bytes 58545041, dropped 0, multicast packets 0 input errors 0, length 0, overrun 0, CRC 0, frame 0, fifo 0, missed 0 output packets 56223, bytes 4995566, dropped 0 output errors 0, aborted 0, carrier 0, fifo 0, heartbeat 0, window 0 collisions 0 wm3400-34710C8(config)# wm3400-34710C8(config)#show interface ge 2 on wm3400-34710C8 Interface ge2 is DOWN Hardware-type: ethernet, Mode: Layer 2, Address: 00-15-70-37-FA-C0 Index: 2002, Metric: 1, MTU: 1500 Speed: Admin Auto, Operational n/a, Maximum 1G Duplex: Admin Auto, Operational n/a Active-medium: n/a Switchport settings: access, access-vlan: 1 Input packets 0, bytes 0, dropped 0 Received 0 unicasts, 0 broadcasts, 0 multicasts Input errors 0, runts 0, giants 0 on <DEVICE-NAME> Displays interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. port-channel <1-2> Displays port channel interface status and configuration <1-2> Specify the port channel index from 1 - 2. switch port {on <DEVICE-NAME>} Displays layer 2 interface status on <DEVICE-NAME> Optional. Displays interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. vlan <1-4094> {on <DEVICE-NAME>} Displays VLAN interface status and configuration <1-4094> Specify the Switch Virtual Interface (SVI) VLAN ID from 1 - 4094. on <DEVICE-NAME> Optional. Displays interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
TM 4000 Series Access Point CLI Reference Guide 473 ip show commands Displays IP related information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show ip [arp|ddns|dhcp|dhcp-vendor-options|domain-name|igmp|interface| name-server|nat|ospf|route|routing] show ip arp {<VLAN-NAME> {on <DEVICE-NAME>}|on <DEVICE-NAME>} show ip ddns bindings {on <DEVICE-NAME>} show ip dhcp [binding|networks|status] show ip dhcp [networks|status] {on <DEVICE-NAME>}] show ip dhcp binding {manual <DEVICE-NAME>|on <DEVICE-NAME>} show ip [dhcp-vendor-options|domain-name|name-server|routing] {on <DEVICE- NAME>} show ip igmp snooping [mrouter|vlan] show ip igmp snooping mrouter vlan <1-4095> {on <DEVICE-NAME>} show ip igmp snooping vlan <1-4095> {<IP> {on <DEVICE-NAME>}| on <DEVICE-NAME>} show ip interface {<INTERFACE> {on <DEVICE-NAME>}|brief {on <DEVICE-NAME>}| on <DEVICE-NAME>} show ip nat translations verbose {on <DEVICE-NAME>} show ip route {<INTERFACE>|ge <1-4>|me1|port-channel <1-2>|vlan <1-4094>} {on <DEVICE-NAME>} show ip route {on <DEVICE-NAME>} show ip ospf [border-router|interface|neighbor|on|route|stats] show ip ospf interface {on {<on> <DEVICE-NAME>}|vlan <1-4094> {on <DEVICE- NAME>}] show ip ospf [border-router|neighbor|route|on|stats] {on <DEVICE-NAME>}
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 474 NOTE The show ip ospf command is also available under profileand device modes. Parameters show ip arp {<VLAN-NAME> {on <DEVICE-NAME>}|on <DEVICE-NAME>} show ip ddns bindings {on <DEVICE-NAME>} show ip dhcp [networks|status] {on <DEVICE-NAME>} show ip dhcp binding {manual {on <DEVICE-NAME>}|on <DEVICE-NAME>} ip arp Displays Address Resolution Protocol (ARP) configuration details <VLAN-NAME> {on <DEVICE-NAME>} Optional. Displays ARP configuration on a specified VLAN. Specify the VLAN name. on <DEVICE-NAME> Optional. Displays VLAN ARP configuration on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Displays VLAN ARP configuration details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip ddns Displays Dynamic Domain Name Server (DDNS) configuration details bindings {on <DEVICE-NAME>} Displays DDNS address bindings on <DEVICE-NAME> Optional. Displays address bindings on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip dhcp Displays the DHCP server configuration details networks {on <DEVICE-NAME>} Displays the DHCP server network details on <DEVICE-NAME> Optional. Displays server network details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. status {on <DEVICE- NAME>} Displays the DHCP server status on <DEVICE-NAME> Optional. Displays server status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip dhcp Displays the DHCP server configuration details bindings Displays DHCP address bindings manual {on <DEVICE- NAME>} Displays static DHCP address bindings on <DEVICE-NAME> Optional. Displays address bindings on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Displays DHCP address bindings on a specified device <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 475 show ip [dhcp-vendor-options|domain-name|name-server|routing] {on <DEVICE- NAME>} show ip igmp snooping mrouter vlan <1-4095> {on <DEVICE-NAME>} show ip igmp snooping vlan <1-4095> {<IP> {on <DEVICE-NAME>}|on <DEVICE- NAME>} show ip interface {<INTERFACE> {on <DEVICE-NAME>}|brief {on <DEVICE-NAME>}} ip dhcp-vendor-options {on <DEVICE-NAME>} Displays DHCP 43 parameters received from the DHCP server on <DEVICE-NAME> Optional. Displays DHCP 43 parameters received from a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip domain-name {on <DEVICE-NAME>} Displays DNS default domain on <DEVICE-NAME> Optional. Displays the default domain on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip name-server {on <DEVICE-NAME>} Display the DNS name server details on <DEVICE-NAME> Optional. Displays server details on a specified device <DEVICE-NAME> Specify the name of the AP or the wireless controller. ip routing {on <DEVICE-NAME>} Displays the routing status on <DEVICE-NAME> Optional. Displays routing details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip igmp Displays IGMP configuration details snooping Displays IGMP snooping configuration details mrouter vlan <1-4095> {on <DEVICE-NAME>} Displays VALN IGMP snooping mrouter configuration <1-4095> Specify the VLAN ID from 1 - 4095. on <DEVICE-NAME> Optional. Displays details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip igmp Displays IGMP configuration details snooping Displays IGMP snooping configuration details vlan <1-4095> Displays VLAN IGMP snooping configuration <1-4095> Specify the VLAN ID from 1 - 4095. <IP> {on <DEVICE-NAME>} Optional. Specify the multicast group IP address. on <DEVICE-NAME> Optional. Displays configuration details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip interface Displays administrative and operational status of all layer 3 interfaces or a specified layer 3 interface <INTERFACE> {on <DEVICE-NAME>} Displays a specified interface status. Specify the interface name. on <DEVICE-NAME> Optional. Displays interface status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 476 show ip nat translations verbose {on <DEVICE-NAME>} show ip route {<INTERFACE>|ge <1-4>|me1|port-channel <1-2>|vlan <1-4095>} {on <DEVICE-NAME>} brief Displays a brief summary of interface status and configuration on <DEVICE-NAME> Optional. Displays a brief summary on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip nat translations Displays Network Address Translation (NAT) translations verbose Displays detailed NAT translations on <DEVICE-NAME> Optional.Displays NAT translations on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ip route Displays route table details <INTERFACE> {on <DEVICE-NAME>} Displays route table details for a specified interface on <DEVICE-NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ge <1-4> {on <DEVICE-NAME>} Displays GigabitEthernet interface route table details <1-4> Specify the GigabitEthernet interface index from 1 - 4. on <DEVICE-NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. me1 {on <DEVICE-NAME>} Displays FastEthernet interface route table details on <DEVICE-NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. port-channel <1-2> {on <DEVICE-NAME>} Displays port channel interface route table details on <DEVICE_NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. vlan <1-4095> {on <DEVICE-NAME>} Displays VLAN interface route table details on <DEVICE_NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. pppoe1 {on <DEVICE- NAME>} Displays Point-to-point Protocol over Ethernet (PPPoE) interface route table details on <DEVICE-NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. wwan1 {on <DEVICE-NAME>} Displays Wireless WAN route table details on <DEVICE-NAME> Optional. Displays route table details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 477 Example wm3400-34710C8(config)#show ip arp test on wm3400-34710C8E +--------------------+-------------------------+---------------+---------- | IP | MAC | INTERFACE | TYPE | +--------------------+-------------------------+---------------+---------- | 172.16.10.11 | 00-50-DA-95-11-13 | vlan1 | dynamic | | 172.16.10.10 | 00-02-B3-28-D1-55 | vlan1 | dynamic | +--------------------+-------------------------+---------------+---------- wm3400-34710C8(config)# wm3400-34710C8(config)#show ip interface brief on wm3400-34710C8 +-----------------+----------------------------+--------------+----------- | INTERFACE | IP-ADDRESS/MASK | STATUS | PROTOCOL | +-----------------+----------------------------+--------------+----------- | me1 | unassigned | DOWN | down | | vlan44 | unassigned | UP | up | | vlan1 | 172.16.10.2/24 | UP | up | | vlan4 | 157.235.208.252/24 | UP | up | +-----------------+----------------------------+--------------+----------- wm3400-34710C8(config)# wm3400-34710C8(config)#show ip nat translations verbose on wm3400-34710C8 PROTO ACTUAL SOURCE ACTUAL DESTINATION NATTED SOURCE NATTED DESTINATION -------------------------------------------------------------------------- wm3400-34710C8(config)# wm3400-34710C8(config)#show ip route test on wm3400-34710C8 +-------------------------+--------------------+------------+------------- | DESTINATION | GATEWAY | FLAGS | INTERFACE | +-------------------------+--------------------+------------+------------- | 157.235.208.0/24 | direct | C | vlan4 | | 172.16.10.0/24 | direct | C | vlan1 | | default | 172.16.10.9 | CG | vlan1 | +-------------------------+--------------------+------------+------------- Flags: C - Connected G - Gateway wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 478 wm3400-34710C8(config)#show ip route pc 2 +-------------------------+--------------------+------------+------------- | DESTINATION | GATEWAY | FLAGS | INTERFACE | +-------------------------+--------------------+------------+------------- | 157.235.208.0/24 | direct | C | vlan4 | | 172.16.10.0/24 | direct | C | vlan1 | | default | 172.16.10.9 | CG | vlan1 | +-------------------------+--------------------+------------+------------- Flags: C - Connected G - Gateway wm3400-34710C8config)# wm3400-34710C8(config)#show ip route vlan 1 on wm3400-34710C8 +------------------------+---------------------+-------------+------------ | DESTINATION | GATEWAY | FLAGS | INTERFACE | +------------------------+---------------------+-------------+------------ | 172.16.10.0/24 | direct | C | vlan1 | | default | 172.16.10.9 | CG | vlan1 | +------------------------+---------------------+-------------+------------ Flags: C - Connected G - Gateway wm3400-34710C8(config)# wm3400-34710C8(config)#show ip route ge 1 on wm3400-34710C8---------------- ---------------------------------------------------------- DESTINATION GATEWAY FLAGS INTERFACE -------------------------------------------------------------------------- 172.16.12.0/24 direct C vlan3 172.16.11.0/24 direct C vlan2 172.16.10.0/24 direct C vlan1 -------------------------------------------------------------------------- Flags: C - Connected G - Gateway wm3400-34710C8(config)# wm3400-34710C8(config)#show ip routing on wm3400-34710C8 IP routing is enabled. wm3400-34710C8(config)# wm3400-34710C8(config)#show ip dhcp status on wm3400-34710C8 State of DHCP server: running Interfaces: vlan2, vlan3 wm3400-34710C8(config)# wm3400-34710C8(config)#show ip ospf route on wm3400-34710C8 wm3400-34710C8(config)# wm3400-34710C8(config)#show ip ospf state on wm3400-34710C8 Maximum number of OSPF routes allowed: 9216 Number of OSPF routes received: 0
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 479 Ignore-count allowed: 5, current ingore-count: 0 Ignore-time 60 seconds, reset-time 360 seconds Current OSPF process state: Running wm3400-34710C8(config)# wm3400-34710C8(config)#show ip ospf border-router on wm3400-34710C8 wm3400-34710C8(config)# wm3400-34710C8(config)#show ip ospf neighbor on wm3400-34710C8 wm3400-34710C8(config)# wm3400-34710C8(config-device-00-15-70-37-FA-BE)#show ip route pppoe1 on wm3400-37FABE -------------------------------------------------------------------------- DESTINATION GATEWAY FLAGS INTERFACE -------------------------------------------------------------------------- 192.168.0.0/24 direct C me1 172.16.10.0/24 direct C vlan1 -------------------------------------------------------------------------- Flags: C - Connected G - Gateway
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 480 ip-access-list-stats show commands Displays IP access list statistics NOTE This command is not available in the USER EXEC Mode Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show ip-access-list-stats {<IP-ACCESS-LIST> {on <DEVICE-NAME>}|on <DEVICE- NAME>} Parameters show ip-access-list-stats {<IP-ACCESS-LIST> {on <DEVICE-NAME>}| on <DEVICE-NAME>} Example wm3400-34710C8(config)#show ip-access-list-stats IP Access-list: # Restrict Management ACL # permit tcp any any eq ftp rule-precedence 1 Hitcount: 0 permit tcp any any eq www rule-precedence 2 Hitcount: 41 permit tcp any any eq ssh rule-precedence 3 Hitcount: 448 ip-access-list-stats Displays IP access list statistics <IP-ACCESS-LIST> {on <DEVICE-NAME>} Displays statistics for a specified IP access list <IP-ACCESS-LIST> Optional. Specify the IP access list name. on <DEVICE-NAME> Optional. Displays statistics on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Displays all IP access list statistics on a specified device <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 481 permit tcp any any eq https rule-precedence 4 Hitcount: 0 permit udp any any eq snmp rule-precedence 5 Hitcount: 0 permit tcp any any eq telnet rule-precedence 6 Hitcount: 4
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 482 l2tpv3 show commands Displays L2TPV3 information Supported on the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax l2tpv3 {on|tunnel|tunnel-summary} l2tpv3 {on <DEVICE-NAME>|tunnel [<L2TPV3-TUNNEL-NAME>] {on|session}} l2tpv3 tunnel-summary {down {on <DEVICE-NAME>}|on <DEVICE-NAME>| up {on <DEVICE-NAME>}} Parameters l2tpv3 {on <DEVICE-NAME>|tunnel [<L2TPV3-TUNNEL-NAME>] {on|session}} l2tpv3 tunnel-summary {down {on <DEVICE-NAME>}|on <DEVICE-NAME>| up {on <DEVICE-NAME>}} on <DEVICE-NAME> Optional. Displays L2TPV3 information on the device specified by the <DEVICE-NAME> parameter tunnel <L2TPV3-TUNNEL- NAME> Optional. Displays a specified L2TPV3 tunnel information <L2TPV3-TUNNEL-NAME> {on|session} Specify the L2TPV3 tunnel name. on <DEVICE-NAME> Optional. Displays a specified L2TPV3 tunnel information on the device specified by the <DEVICE-NAME> parameter. session <L2TPV3-SESSION-NAME> Optional. Displays a specified L2TPV3 tunnel session information <L2TPV3-SESSION-NAME> {on <DEVICE-NAME>} Specify the session name to view information. on <DEVICE-NAME> Optional. Displays session information on the device specified by the <DEVICE-NAME> parameter. tunnel-summary Optional. Displays L2TPV3 tunnels summary down {on <DEVICE-NAME>} Optional. Displays unestablished tunnels summary on <DEVICE-NAME> Optional. Displays unestablished tunnels summary on the device specified by the <DEVICE-NAME> parameter on <DEVICE-NAME> Optional. Displays L2TPV3 tunnel summary on the device specified by the <DEVICE- NAME> parameter
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 483 Example wm3400-34710C8(config)#show l2tpv3 wm3400-34710C8(config)# wm3400-34710C8(config)#show l2tpv3 on 172.16.10.1 % Error processing 'show l2tpv3 on 172.16.10.1 ': Traceback (most recent call last): File "/data/wing5.3-trunk/obj/qs5/src/sys/cfgd/cli/show.py", line 129, in _show_read File "/data/wing5.3-trunk/obj/qs5/src/sys/cfgd/l2tpv3/ l2tpv3_statscli.py", line 80, in l2tpv3_all_stats NameError: global name 'e' is not defined wm3400-34710C8(config)# wm3400-34710C8(config)#show l2tpv3 tunnel-summary Session Name : 1 VLANs : 11 10 13 12 14 9 Pseudo Wire Type : Ethernet_VLAN Serial number for the session : 31 Local Session ID : 267330235 Remote Session ID : 27841566 Size of local cookie (0, 4 or 8 bytes) : 0 First word of local cookie : 0 Second word of local cookie : 0 Size of remote cookie (0, 4 or 8 bytes) : 0 First word of remote cookie : 0 Second word of remote cookie : 0 Session state : Established Remote End ID : 109 Trunk Session : 1 Native VLAN tagged : 0 Native VLAN ID : 9 Number of packets received : 0 Number of bytes received : 0 Number of packets sent : 994 Number of bytes sent : 93804 Number of packets dropped : 0 wm3400-34710C8(config)# up {on <DEVICE-NAME>} Optional. Displays summary of established tunnels on <DEVICE-NAME> Optional. Displays summary of tunnels established on the device specified by the <DEVICE-NAME> parameter
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 484 licenses show commands Displays installed licenses and usage information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show licenses Parameters None Example wm3400-34710C8(config)#show licenses Serial Number : 6268529900014 Device Licenses: AP-LICENSE String : 8088bb045018988b85bcd575d0ab7dbc802885bcc680a96194dfbeedc28d4117058eb53bd8b Value : 50 Used : 0 AAP-LICENSE String : 8088bb045018988bf98ff7127cda1d354bc689885fcc6b625b695384946d4117058eb53bd8b Value : 50 Used : 0 wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 485 lldp show commands Displays Link Layer Discovery Protocol (LLDP) information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show lldp neighbors {on <DEVICE-NAME>} Parameters show lldp neighbors {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show lldp neighbors wm3400-34710C8(config)# wm3400-34710C8(config)#show lldp neighbors on wm3400-34710C8 wm3400-34710C8(config)# lldp Displays LLDP neighbor table on <DEVICE-NAME> Optional. Displays LLDP neighbor table on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 486 logging show commands Displays network activity log Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show logging {on <DEVICE-NAME>} Parameters show logging {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show logging on wm3400-34710C8 Logging module: enabled Aggregation time: disabled Console logging: level warnings Monitor logging: disabled Buffered logging: level warnings Syslog logging: level warnings Facility: local7 Log Buffer (2294 bytes): Jul 08 16:44:26 2011: %CERTMGR-4-CERT_EXPIRY: server certificate for trustpoint mint_security_trustpoint has expired Jul 08 16:44:26 2011: %CERTMGR-4-CERT_EXPIRY: ca certificate for trustpoint mint_security_trustpoint has expired Jul 08 15:44:26 2011: %CERTMGR-4-CERT_EXPIRY: server certificate for trustpoint mint_security_trustpoint has expired logging {on <DEVICE-NAME>} Displays logging information on a specified device <DEVICE-NAME> Optional. Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 487 Jul 08 15:44:26 2011: %CERTMGR-4-CERT_EXPIRY: ca certificate for trustpoint mint_security_trustpoint has expired Jul 08 14:44:26 2011: %CERTMGR-4-CERT_EXPIRY: server certificate for trustpoint mint_security_trustpoint has expired Jul 08 14:44:26 2011: %CERTMGR-4-CERT_EXPIRY: ca certificate for trustpoint mint--More-- wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 488 mac-access-list-stats show commands Displays MAC access list statistics NOTE This command is not present in USER EXEC Mode Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show mac-access-list-stats {<MAC-ACCESS-LIST> {on <DEVICE-NAME>}| on <DEVICE-NAME>} Parameters show mac-access-list-stats {<MAC-ACCESS-LIST> {on <DEVICE-NAME>}|on <DEVICE-NAME>} Example wm3400-34710C8(config)#show mac-access-list-stats on wm3400-34710C8E wm3400-34710C8(config)# mac-access-list-stats Displays MAC access list statistics <MAC-ACCESS-LIST> {on <DEVICE-NAME>} Displays statistics for a specified MAC access list <MAC-ACCESS-LIST> Optional. Specify the MAC access list name. on <DEVICE-NAME> Optional. Displays statistics on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Displays MAC access list statistics on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 489 mac-address-table show commands Displays MAC address table entries Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show mac-address-table {on <DEVICE-NAME>} Parameters show mac-address-table {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show mac-address-table on wm3400-34710C8 +------------+----------+-----------+-------------------------+----------- | BRIDGE | VLAN | PORT | MAC | STATE | +------------+----------+-----------+-------------------------+----------- | 1 | 1 | ge1 | 00-50-DA-EE-B5-5C | forward | | 1 | 1 | ge1 | 00-A0-F8-00-00-00 | forward | | 1 | 1 | ge1 | 00-02-B3-28-D1-55 | forward | | 1 | 1 | ge1 | 00-A0-F8-68-D5-5D | forward | | 1 | 1 | ge1 | 00-50-DA-95-11-13 | forward | | 1 | 1 | ge1 | 00-15-70-38-06-53 | forward | mac-address-table Displays MAC address table entries on <DEVICE-NAME> Optional. Displays MAC address table entries on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
TM 4000 Series Access Point CLI Reference Guide 491 mint show commands Displays MiNT protocol configuration commands Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show mint [config|dis|id|info|known-adopters|links|lsp|lsp-db|mlcp| neighbors|route|stats|tunneled-vlans] show mint [config|id|info|known-adopters|route|stats|tunneled-vlans] {on <DEVICE-NAME>} show mint [dis|links|neighbors] {details {on <DEVICE-NAME>}| on <DEVICE-NAME>} show mint lsp-db {details <AA.BB.CC.DD> {on <DEVICE-NAME>}|on <DEVICE-NAME> show mint mlcp {history {on <DEVICE-NAME>}|on <DEVICE-NAME>} Parameters show mint [config|id|info|known-adopters|route|stats|tunneled-vlans] {on <DEVICE-NAME>} mint Displays MiNT protocol information based on the parameters passed config Displays MiNT related configuration details id Displays local MiNT ID known-adopters Displays known, possible, or reachable adopters route Displays MiNT route table details stats Displays MiNT related statistics tunneled-vlans Displays MiNT tunneled VLAN details on <DEVICE-NAME> The following are common to all of the above: on <DEVICE-NAME> Optional. Displays MiNT protocol details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 492 show mint [dis|links|neighbors] {details {on <DEVICE-NAME>}|on <DEVICE- NAME>} show mint lsp-db {details <AA.BB.CC.DD> {on <DEVICE-NAME>}|on <DEVICE- NAME>} show mint mlcp {history {on <DEVICE-NAME>}|on <DEVICE-NAME>} Example wm3400-34710C8(config)#show mint stats 0 L1 neighbors L1 LSP DB size 1 LSPs (0 KB) 1 L1 routes Last SPFs took 0s SPF (re)calculated 1 times. levels 1 base priority 180 dis priority 180 wm3400-34710C8(config)# wm3400-34710C8(config)#show mint lsp id 70.37.fa.be, level 1, seqnum 18640, 0 adjacencies, 0 extended-vlans, expires in 1145 seconds, republish in 722 seconds, changed True, ext-vlan FDB pri 0, 180 bytes wm3400-34710C8(config)#show mint lsp-db Level 1 LSPs mint Displays MiNT protocol information based on the parameters passed dis Displays MiNT network Designated Intermediate Systems (DISes) links Displays MiNT networking link details neighbors Displays adjacent MiNT peer details details {on <DEVICE-NAME>}I on <DEVICE-NAME> The following are common to the dis, links, and neighbors parameters: details Optional. Displays detailed MiNT information on <DEVICE-NAME> Optional. Displays MiNT information on a specified device mint Displays MiNT protocol information based on the parameters passed lsp-db Displays MiNT LSP database entries details <AA.BB.CC.DD> {on <DEVICE-NAME>} Optional. Displays detailed MiNT LSP database entries <AA.BB.CC.DD> Specify the MiNT address in the <AA.BB.CC.DD> format. on <DEVICE-NAME> Optional. Displays MiNT LSP database entries on a specified device mint Displays MiNT protocol information based on the parameters passed mlcp Displays MiNT Link Creation Protocol (MLCP) status history {on <DEVICE-NAME>} Optional. Displays MLCP client history on <DEVICE-NAME> Optional. Displays MLCP client history on a specified device
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 493 70.37.fa.be: seqnum 18640, 0 adjacencies, 0 extended-vlans, expires in 1138 seconds 1 LSPs in level 1 database wm3400-34710C8(config)#show mint route on wm3400-34710C8 Destination : Next-Hop(s) 70.37.FA.BE : 70.37.FA.BE via self wm3400-34710C8(config)# wm3400-34710C8(config)#show mint known-adopters on wm3400-34710C8 70.37.FA.BE wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 494 noc show commands Displays Network Operations Center (NOC) level information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show noc [client-list|device|domain] show noc device {filter {offline|online|rf-domain {<DOMAIN-NAME>| not <DOMAIN-NAME>]} show noc domain [managers|statistics {details}] Parameters show noc client-list show noc device {filter {offline|online|rf-domain {<DOMAIN-NAME>|not <DOMAIN-NAME>}} noc client-list Displays a list of clients at the NOC level noc device filter Displays devices in a network filter Optional. Displays network devices Use additional filters to view specific details offline Displays offline devices online Displays online devices rf-domain {<DOMAIN-NAME>| not <DOMAIN-NAME>} Displays devices on a specified RF Domain <DOMAIN-NAME> Optional. Specify the name of the RF Domain. not <DOMAIN-NAME> Inverts the selection
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 495 show noc domain [managers|statistics {details}] Example wm3400-34710C8(config)#show noc device +-----------------+----------------+--------+----------------+------------ | MAC| HOST-NAME | TYPE| CLUSTER| RF-DOMAIN |ADOPTED-BY| ONLINE | +-----------------+----------------+--------+----------------+------------ |99-88-77-66-55-44| ap4700-665544| ap4700| | default| | offline | |00-15-70-88-9E-C4| ap4700-889EC4| ap4700| | default| | offline | |11-22-33-44-55-66| ap4600-445566| ap4600| | default| | offline | |00-15-70-37-FA-BE| wm3400-34710C8| WM3700| | default| | online | +-----------------+----------------+--------+----------------+------------ Total number of clients displayed: 4 wm3400-34710C8(config)# wm3400-34710C8(config)#show noc domain statistics details ========================================================================== RF-Domain RFDOMAIN_UseCase1 Note: TX = AP->Client, RX = Client->AP -------------------------------------------------------------------------- Data bytes : ( TX + RX = Total ), 0 + 0 = 0 bytes Data throughput : ( TX + RX = Total ), 0 Kbps + 0 Kbps = 0 Kbps Data packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Data pkts/sec : ( TX + RX = Total ), 0 + 0 = 0 pps BCMC Packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Management Packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Packets Discarded : 0 - Tx Dropped, 0 - Rx Errors Indicators : T = 0 @ Max user rate of 0 Kbps Distribution : 0 Clients, 0 radios Client count Detais : 0/0/0 (b/bg/bgn); 0/0 (a/an) Stats Update Info : 6 seconds - update interval, mode is auto Threat Level : 0 Cause of concern : Remedy : Last update : 2010-01-31 10:30:22 by 00-15-70-37-FA-BE -------------------------------------------------------------------------- Total number of RF-domain displayed: 1 wm3400-34710C8(config-rf-domain-RFDOMAIN_UseCase1)# wm3400-34710C8(config)#show noc device filter online noc domain Displays RF Domain information Use this command to view all domain managers and get RF Domain statistics managers Lists RF Domains and managers statistics {details} Displays RF Domains statistics details Optional. Provides detailed RF Domain statistics
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 496 -------------------------------------------------------------------------- MAC HOST-NAME TYPE CLUSTER RF-DOMAIN ADOPTED-BY ONLINE -------------------------------------------------------------------------- 00-15-70-37-FA-BE wm3400-34710C8 WM3700 RFDOMAI..echPubs online -------------------------------------------------------------------------- Total number of clients displayed: 1 wm3400-34710C8(config)# wm3400-34710C8(config)#show noc domain statistics details ==========================================================================R F-Domain RFDOMAIN_TechPubs Note: TX = AP->Client, RX = Client->AP -------------------------------------------------------------------------- Data bytes : ( TX + RX = Total ), 0 + 0 = 0 bytes Data throughput : ( TX + RX = Total ), 0 Kbps + 0 Kbps = 0 Kbps Data packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Data pkts/sec : ( TX + RX = Total ), 0 + 0 = 0 pps BCMC Packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Management Packets : ( TX + RX = Total ), 0 + 0 = 0 pkts Packets Discarded : 0 - Tx Dropped, 0 - Rx Errors Indicators : T = 0 @ Max user rate of 0 Kbps Distribution : 0 Clients, 0 radios Client count Detais : 0/0/0 (b/bg/bgn); 0/0 (a/an) Stats Update Info : 6 seconds - update interval, mode is auto Threat Level : 1 Cause of concern : no sensors enabled in RF-domain RFDOMAIN_TechPubs Remedy : enable AP detection Last update : 2011-01-09 08:44:15 by 00-15-70-37-FA-BE -------------------------------------------------------------------------- Total number of RF-domain displayed: 1 wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 497 ntp show commands Displays Network Time Protocol (NTP) information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show ntp [associations|status] show ntp [associations {detail|on}|status {on <DEVICE-NAME>} Parameters show ntp [associations {detail|on}|status {on <DEVICE-NAME>}] Example wm3400-34710C8>show ntp associations address ref clock st when poll reach delay offset disp * master (synced), # master (unsynced), + selected, - candidate, ~ configured wm3400-34710C8> wm3400-34710C8>show ntp status Clock is synchronized, stratum 0, actual frequency is 0.0000 Hz, precision is 2**0 reference time is 00000000.00000000 (Feb 07 06:28:16 UTC 2036) ntp associations {detail|on} Displays existing NTP associations detail Optional. Displays detailed NTP associations on <DEVICE-NAME> Optional. Displays NTP associations on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. ntp status {on <DEVICE-NAME>} Displays NTP association status on <DEVICE-NAME> Optional. Displays NTP association status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 498 clock offset is 0.000 msec, root delay is 0.000 msec root dispersion is 0.000 msec wm3400-34710C8> wm3400-34710C8>show ntp status Clock is synchronized, stratum 0, actual frequency is 0.0000 Hz, precision is 2^0 reference time is 00000000.00000000 (Feb 07 06:28:16 UTC 2036) clock offset is 0.000 msec, root delay is 0.000 msec root dispersion is 0.000 msec, wm3400-34710C8>
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 499 password-encryption show commands Displays password encryption status (enabled/disabled) Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show password-encryption status Parameters show password-encryption status Example wm3400-34710C8(config)#show password-encryption status Password encryption is disabled wm3400-34710C8(config)# password-encryption status Displays password encryption status (enabled/disabled)
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 500 power show commands Displays Power Over Ethernet (PoE) information Supported on the following platforms: WM3400 WM3600 Syntax show power [configuration|status] {on <DEVICE-NAME>} Parameters show power [configuration|status] {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show power status on wm3600-37FAAA System Voltage: 53.4 volts Guard Band: 32 watts Power Budget: 190 watts Power Consumption: 0 watts poe device 1 temperature 35C poe device 2 temperature 38C --------------------------------------------------------------------------- ----- PORT VOLTS mA WATTS CLASS STATUS --------------------------------------------------------------------------- ----- ge1 0.0 0 0.0 0 Off ge2 0.0 0 0.0 0 Off ge3 0.0 0 0.0 0 Off ge4 0.0 0 0.0 0 Off ge5 0.0 0 0.0 0 Off ge6 0.0 0 0.0 0 Off ge7 0.0 0 0.0 0 Off ge8 0.0 0 0.0 0 Off power Displays PoE information (PoE configuration and status) configuration {on <DEVICE-NAME>} Displays detailed PoE configuration on <DEVICE-NAME> Optional. Displays configuration on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. status {on <DEVICE-NAME>} Displays PoE status on <DEVICE-NAME> Optional. Displays status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
TM 4000 Series Access Point CLI Reference Guide 502 remote-debug show commands Displays remote debug session information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show remote-debugging Parameters None Example wm3400-34710C8(config)#show remote-debug live-pktcap Not running wireless Not running copy-crashinfo Not running offline-pktcap Not running copy-techsupport Not running more Not running wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 503 rf-domain-manager show commands Displays RF Domain manager selection details Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show rf-domain-manager Parameters None Example wm3400-34710C8(config)#show rf-domain-manager RF Domain default RF Domain Manager: ID: 70.37.fa.be Priority: 9 Has IP connectivity Has non-mesh links Last change 12265 seconds ago This device: Priority: 9 Has IP connectivity Has non-mesh links wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 504 role show commands Displays role based firewall information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show role wireless-clients {on <DEVICE-NAME>} Parameters show role wireless-clients {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show role wireless-clients on wm3400-34710C8E No ROLE statistics found. wm3400-34710C8(config)# role wireless-clients Displays clients associated with roles on <DEVICE-NAME> Optional. Displays clients associated with roles on a specified device
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 505 running-config show commands Displays configuration files (where all configured MAC and IP access lists are applied to an interface) Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show running-config {aaa-policy|association-acl-policy|auto-provisioning- policy|captive-portal-policy|device|dhcp-server-policy|firewall- policy| include-factory|interface|management-policy|profile|radio-qos- policy| rf-domain|smart-rf-policy|wlan|wlan-qos-policy} show running-config {aaa-policy|association-acl-policy|auto-provisioning- policy|captive-portal-policy|dhcp-server-policy|firewall-policy| management-policy|radio-qos-policy|smart-rf-policy|wlan-qos-policy} <POLICY-NAME> {include-factory}} show running-config {device [<MAC>|self] {include-factory}} show running-config {include-factory} show running-config {interface {<INTERFACE>|ge <1-4>|include-factory| me1|port-channel <1-2>|vlan <1-4095>} {include-factory}} show running-config {profile [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700| wm3400|wm3600|wm3700] <PROFILE-NAME> {include-factory}} show running-config {rf-domain <DOMAIN-NAME> {include-factory}} show running-config {wlan <WLAN-NAME> {include-factory}} Parameters show running-config {aaa-policy|association-acl-policy| auto-provisioning-policy|captive-portal-policy|dhcp-server-policy|
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 506 firewall-policy|management-policy|radio-qos-policy|smart-rf-policy|wlan- qos-policy} <PLOICY-NAME> {include-factory} show running-config {device [<MAC>|self] {include-factory}} show running-config {include-factory}} show running-config {interface {<INTERFACE>|ge <1-4>|include- factory|me1|port-channel <1-2>|vlan <1-4095>} {include-factory}} running-config Optional. Displays current configuration details aaa-policy Optional. Displays AAA policy configuration details association-acl-policy Optional. Displays association ACL policy configuration details auto-provisioning-policy Optional. Displays auto provisioning policy configuration details captive-portal-policy Optional. Displays captive portal policy configuration details dhcp-server-policy Optional. Displays the DHCP server policy configuration details firewall-policy Optional. Displays firewall policy configuration details management-policy Optional. Displays management policy configuration details radio-qos-policy Optional. Displays radio QoS policy configuration details smart-rf-policy Optional. Displays Smart RF policy configuration details wlan-qos-policy Optional. Displays WLAN QoS policy configuration details <POLICY-NAME> The following is common to all policies listed above: <POLICY-NAME> Specify the name of the policy. include-factory This parameter is common to all policies listed above. Optional. Includes factory defaults running-config Displays current configuration details device {<MAC>|self} Optional. Displays device configuration details <MAC> Optional. Displays configuration of a specified device. Specify the MAC address of the device. self Optional. Displays the logged devices configuration include-factory The following is common to the <MAC> and self parameters: Optional. Displays factory default values running-config Displays current configuration details include-factory Optional. Includes factory default values running-config Displays current configuration details interface Optional. Displays interface configuration <INTERFACE> Displays a specified interface configuration. Specify the interface name. ge <1-4> Displays GigabitEthernet interface configuration details <1-4> Specify a GigabitEthernet interface index from 1 - 4. me1 Displays FastEthernet interface configuration details port-channel <1-2> Displays port channel interface configuration details <1-2> Specify a port channel interface index from 1 - 2.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 507 show running-config {profile [ap4021|ap4600|ap4511|ap4521|ap4532| ap4700|wm3400|wm3600|wm3700] <PROFILE-NAME> {include-factory}} show running-config {rf-domain <DOMAIN-NAME> {include-factory}} vlan <1-4095> Displays VLAN interface configuration details <1-4095> Specify the VLAN interface number from 1 - 4095. include-factory This parameter is common to all of the interface options. Optional. Includes factory defaults running-config Displays current configuration profile Optional. Displays current configuration for a specified profile ap4021 <PROFILE-NAME> Displays AP4021 profile configuration <PROFILE-NAME> Displays configuration for a specified AP4021 profile. Specify the AP4021 profile name. ap4600 <PROFILE-NAME> Displays AP4600 profile configuration <PROFILE-NAME> Displays configuration for a specified AP4600 profile. Specify the AP4600 profile name. ap4511 <PROFILE-NAME> Displays AP4511 profile <PROFILE-NAME> Displays configuration for a specified AP4511 profile. Specify the AP4511 profile name. ap4521 <PROFILE-NAME> Displays AP4521 profile configuration <PROFILE-NAME> Displays configuration for a specified AP4521 profile. Specify the AP4521 profile name. ap4532 <PROFILE-NAME> Displays AP4532 profile configuration <PROFILE-NAME> Displays configuration for a specified AP4532 profile. Specify the AP4532 profile name. ap4700 <PROFILE-NAME> Displays AP4700 profile configuration <PROFILE-NAME> Displays configuration for a specified AP4700 profile. Specify the AP4700 profile name. wm3400 <PROFILE-NAME> Displays WM3400 profile configuration <PROFILE-NAME> Displays configuration for a specified WM3400 profile. Specify the WM3400 profile name. wm3600 <PROFILE-NAME> Displays WM3600 profile configuration <PROFILE-NAME> Displays configuration for a specified WM3600 profile. Specify the WM3600 profile name. wm3700 <PROFILE-NAME> Displays WM3700 profile configuration <PROFILE-NAME> Displays configuration for a specified WM3600 profile. Specify the WM3600 profile name. include-factory Optional.This parameter is common to all profiles. It includes factory defaults running-config Displays current configuration rf-domain Optional. Displays current configuration for a RF Domain <DOMAIN-NAME> Specify the name of the RF Domain. include-factory Optional. Includes factory defaults
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 508 show running-config {wlan <WLAN-NAME> {include-factory}} Example wm3400-34710C8(config)#show running-config device self ! firewall ratelimit-trust policy default ! management-policy default telnet http server ssh ! firewall-policy default ! mint-security-policy the_policy rejoin-timeout 35 ! device-discover-policy default ! WM3700 00-15-70-37-FA-BE hostname wm3400-34710C8 no country-code bridge vlan 3 bridge vlan 5 ip dhcp trust ip igmp snooping querier version 2 ip igmp snooping querier max-response-time 3 ip igmp snooping querier timer expiry 89 wep-shared-key-auth radius nas-identifier test --More-- wm3400-34710C8(config) wm3400-34710C8(config)#show running-config device 11-22-33-44-55-66 include-factory ! radio-qos-policy default wmm best-effort aifsn 3 wmm video txop-limit 94 wmm video aifsn 1 wmm video cw-min 3 wmm video cw-max 4 wmm voice txop-limit 47 wmm voice aifsn 1 wmm voice cw-min 2 --More-- running-config Displays current configuration wlan Optional. Displays current configuration for a WLAN <DOMAIN-NAME> Displays current configuration for a specified WLAN. Specify the name of the WLAN. include-factory Optional. Includes factory defaults
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 509 session-changes show commands Displays configuration changes made in the current session Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show session-changes Parameters None Example wm3400-34710C8(config)#show session-changes No changes in this session wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 510 session-config show commands Lists active open sessions on a device Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show session-config {include-factory} Parameters show session-config {include-factory} Example wm3400-34710C8(config)#show session-config ! ! Configuration of WM3700 version 5.3.0.0-048B ! ! version 2.1 ! ! ip access-list BROADCAST-MULTICAST-CONTROL permit tcp any any rule-precedence 10 rule-description "permit all TCP traffic" permit udp any eq 67 any eq dhcpc rule-precedence 11 rule-description "permit DHCP replies" deny udp any range 137 138 any range 137 138 rule-precedence 20 rule- description "deny windows netbios" deny ip any 224.0.0.0/4 rule-precedence 21 rule-description "deny IP multicast" deny ip any host 255.255.255.255 rule-precedence 22 rule-description "deny IP local broadcast" session-config include-factory Displays current session configuration include-factory Optional. Includes factory defaults
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 511 permit ip any any rule-precedence 100 rule-description "permit all IP traffic" ! mac access-list PERMIT-ARP-AND-IPv4 permit any any type ip rule-precedence 10 rule-description "permit all IPv4 traffic" permit any any type arp rule-precedence 20 rule-description "permit all ARP traffic" --More-- wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 512 sessions show commands Displays CLI sessions initiated on a device Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show sessions {on <DEVICE-NAME>} Parameters show sessions {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show sessions on wm3400-34710C8 INDEX COOKIE NAME START TIME FROM 1 4 snmp 2011-06-23 07:59:25 127.0.0.1 2 14 admin 2011-06-24 08:12:44 Console 3 15 admin 2011-06-24 08:42:26 172.16.10.10 wm3400-34710C8(config)# sessions Displays CLI sessions initiated on a device on <DEVICE-NAME> Optional. Displays CLI sessions on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 513 smart-rf show commands Displays Smart RF management commands Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show smart-rf [calibration-status|channel-distribution|history|history- timeline| interactive-calibration-config|radio] show smart-rf [calibration-status|channel-distribution|history|history- timeline| interactive-calibration-config] {on <DOMAIN-NAME>}] show smart-rf radio {<MAC>|activity|all-11an|all-11bgn|energy|neighbors|on <DOMAIN- NAME>] show smart-rf radio {<MAC>|all-11an|all-11bgn|energy <MAC>} {on <DOMAIN- NAME>} show smart-rf radio {activity|neigbors}{<MAC>|all-11an|all-11bgn|on <DOMAIN-NAME>} show smart-rf radio {activity|neigbors}{<MAC>|all-11an|all-11bgn} {on <DOMAIN- NAME>} Parameters show [calibration-status|channel-distribution|history|history-timeline| interactive-calibration-config] {on <DOMAIN-NAME>} calibration-status {on <DOMAIN-NAME>} Displays Smart RF calibration status on <DOMAIN-NAME> Optional. Displays Smart RF calibration status on a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 514 show smart-rf radio {<MAC>|all-11an|all-11bgn|energy <MAC>}{on <DOMAIN- NAME>} show smart-rf radio {activity|neighbors} {<MAC>|all-11an|all-11bgn} {on <DOMAIN-NAME>} channel-distribution {on <DOMAIN-NAME>} Displays Smart RF channel distribution on <DOMAIN-NAME> Optional. Displays Smart RF channel distribution on a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name. history {on <DOMAIN-NAME>} Displays Smart RF calibration history on <DOMAIN NAME> Optional. Displays Smart RF calibration history on a specified RF Domain <DOMAIN NAME> Specify the RF Domain name. history-timeline {on <DOMAIN-NAME>} Displays extended Smart RF calibration history on an hourly or daily timeline on <DOMAIN-NAME> Optional. Displays extended timeline on a specified RF Domain <DOMAIN NAME> Specify the RF Domain name. interactive-calibration-config {on <DOMAIN-NAME>} Displays simulated calibration configuration on <DOMAIN-NAME> Optional. Displays configuration on a specified RF Domain on <DOMAIN-NAME> Specify the RF Domain name. radio Displays radio related commands <MAC> Optional. Displays details of a specified radio. Specify the MAC address of the radio in a <AA-BB-CC-DD-EE-FF> format. all-11an Optional. Displays all 11a radios currently in the configuration all-11bgn Optional. Displays all 11bg radios currently in the configuration energy {<MAC>} Optional. Displays radio energy Specify the MAC address of the radio <MAC> Optional. Specify the radios MAC address in the <AA-BB-CC-DD-EE-FF> format. on <DOMAIN-NAME> The following is common to above parameters: on <DOMAIN-NAME> Optional. Displays radio details on a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name. radio Displays radio related commands activity Optional. Displays changes related to radio power, number of radio channels, or coverage holes. Use additional filters to view specific details. <MAC> Optional. Displays radio activity for a specified radio <MAC> Specify the MAC address of the radio. all-11an Optional. Displays radio activity of all 11a radios in the configuration all-11bgn Optional.Displays radio activity of all 11bg radios in the configuration on <DOMAIN-NAME> Optional. Displays radio activity of all radios within a specified RF Domain <DOMAIN-NAME> Specify the RF Domain name.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 515 Example wm3400-34710C8(config)#show smart-rf calibration-status No calibration currently in progress wm3400-34710C8(config)# wm3400-34710C8(config)#show smart-rf history wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 516 spanning-tree show commands Displays spanning tree information Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show spanning-tree mst {configuration|detail|instance|on} show spanning-tree mst {configuration {(on <DEVICE-NAME>)}} show spanning-tree mst {detail interface {<INTERFACE>|ge<1-4>|me1| port-channel<1-2>|vlan <1-4094>} {(on <DEVICE-NAME>)}} show spanning-tree mst {instance <1-15> {interface <INTERFACE>} {(on <DEVICE-NAME>)}} Parameters show spanning-tree mst {configuration {(on <DEVICE-NAME>)}} show spanning-tree mst {detail interface {<Interfaced <1-4>|me1| port-channel <1-2>|vlan <1-4094>} {(on <DEVICE-NAME>)}} spanning-tree Displays spanning tree information mst Displays Multiple Spanning Tree (MST) configuration configuration {on <DEVICE-NAME>} Optional. Displays MST configuration on <DEVICE-NAME> Optional. Displays MST configuration on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. spanning-tree Displays spanning tree information mst Displays MST configuration detail Optional. Displays detailed MST configuration based on the parameters passed
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 517 show spanning-tree mst {instance <1-15> {interface <INTERFACE>} {(on <DEVICE-NAME>)}} Example wm3400-34710C8(config)#show spanning-tree mst configuration on wm3400- 34710C8 %% % MSTP Configuration Information for bridge 1 : %%------------------------------------------------------ % Format Id : 0 % Name : My Name % Revision Level : 0 % Digest : 0xac36177f50283cd4b83821d8ab26de62 %%------------------------------------------------------ interface [<INTERFACE>| age <1-4>|me1| port-channel <1-2>| van <1-4094>] Displays detailed MST configuration for a specified interface <INTERFACE> Displays detailed MST configuration for a specified interface. Specify the interface name. age <1-4> Displays GigabitEthernet interface MST configuration <1-4> Select the GigabitEthernet interface index from 1 - 4. me1 Displays FastEthernet interface MST configuration port-channel Displays port channel interface MST configuration <1-2> Select the port channel interface index from 1 - 2. vlan Displays VLAN interface MST configuration <1-4094> Select the SVI VLAN ID from 1 - 4094. on <DEVICE-NAME> Optional. Displays detailed MST configuration on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. spanning-tree Displays spanning tree information mst Displays MST configuration. Use additional filters to view specific details. instance <1-15> Optional. Displays information for a particular MST instance <1-15> Specify the instance ID from 1 - 15. interface [<INTERFACE>| ge <1-4>|me1| port-channel <1-2>| vlan <1-4094>] Optional. Displays MST configuration for a specific interface instance. The options are: <INTERFACE> Displays MST configuration for a specified interface. Specify the interface name. ge Displays GigabitEthernet interface MST configuration <1-4> Select the GigabitEthernet interface index from 1 - 4. me1 Displays FastEthernet interface MST configuration port-channel Displays port channel interface MST configuration <1-2> Select the port channel interface index from 1 - 2. vlan Displays VLAN interface MST configuration <1-4094> Select the SVI VLAN ID from 1 - 4094. on <DEVICE-NAME> Optional. Displays MST configuration on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 518 wm3400-34710C8(config)# wm3400-34710C8(config)#show spanning-tree mst detail interface test on wm3400-34710C8 % Bridge up - Spanning Tree Disabled % CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768 % Forward Delay 15 - Hello Time 2 - Max Age 20 - Max hops 20 % 1: CIST Root Id 800000157037fabf % 1: CIST Reg Root Id 800000157037fabf % 1: CIST Bridge Id 800000157037fabf % portfast bpdu-filter disabled % portfast bpdu-guard disabled % portfast portfast errdisable timeout disabled % portfast errdisable timeout interval 300 sec % cisco interoperability not configured - Current cisco interoperability off wm3400-34710C8(config)# wm3400-34710C8(config)#show spanning-tree mst detail % Bridge up - Spanning Tree Disabled % CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768 % Forward Delay 15 - Hello Time 2 - Max Age 20 - Max hops 20 % 1: CIST Root Id 800000157037fabf % 1: CIST Reg Root Id 800000157037fabf % 1: CIST Bridge Id 800000157037fabf % 1: portfast bpdu-guard disabled % portfast portfast errdisable timeout disabled % portfast errdisable timeout interval 300 sec % cisco interoperability not configured - Current cisco interoperability off % ge4: Port 2004 - Id 87d4 - Role Disabled - State Forwarding % ge4: Designated External Path Cost 0 - Internal Path Cost 0 % ge4: Configured Path Cost 11520 - Add type Implicit - ref count 1 % ge4: Designated Port Id 0 - CST Priority 128 % ge4: ge4: CIST Root 0000000000000000 % ge4: ge4: Regional Root 0000000000000000 % ge4: ge4: Designated Bridge 0000000000000000 % ge4: Message Age 0 - Max Age 0 % ge4: CIST Hello Time 0 - Forward Delay 0 % ge4: CIST Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 % ge4: Version Multiple Spanning Tree Protocol - Received None - Send MSTP % ge4: Portfast configured - Current portfast on % ge4: portfast bpdu-guard enabled - Current portfast bpdu-guard off % ge4: portfast bpdu-filter enabled - Current portfast bpdu-filter off % ge4: no root guard configured - Current root guard off % ge4: Configured Link Type point-to-point - Current point-to-point % ge3: Port 2003 - Id 87d3 - Role Disabled - State Forwarding % ge3: Designated External Path Cost 0 - Internal Path Cost 0 % ge3: Configured Path Cost 11520 - Add type Implicit - ref count 1 % ge3: Designated Port Id 0 - CST Priority 128
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 519 --More-- wm3400-34710C8(config)# wm3400-34710C8(config)#show spanning-tree mst instance 1 interface test on wm3400-34710C8 wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 520 startup-config show commands Displays complete startup configuration script Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show startup-config {include-factory} Parameters show startup-config {include-factory} Example rwm3400-34710C8(config)#show startup-config include-factory ! ! Configuration of WM3700 version 5.3.0.0-048B ! ! version 2.1 ! ! ip access-list BROADCAST-MULTICAST-CONTROL permit tcp any any rule-precedence 10 rule-description "permit all TCP traffic" permit udp any eq 67 any eq dhcpc rule-precedence 11 rule-description "permit DHCP replies" deny udp any range 137 138 any range 137 138 rule-precedence 20 rule- description "deny windows netbios" deny ip any 224.0.0.0/4 rule-precedence 21 rule-description "deny IP multicast" deny ip any host 255.255.255.255 rule-precedence 22 rule-description "deny IP local broadcast" startup-config include-factory Displays startup configuration script include-factory Optional. Includes factory defaults
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 521 permit ip any any rule-precedence 100 rule-description "permit all IP traffic" ! mac access-list PERMIT-ARP-AND-IPv4 permit any any type ip rule-precedence 10 rule-description "permit all IPv4 traffic" permit any any type arp rule-precedence 20 rule-description "permit all ARP traffic" --More-- wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 522 terminal show commands Displays terminal configuration parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show terminal Parameters None Example wm3400-34710C8(config)#show terminal Terminal Type: xterm Length: 45 Width: 126 wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 523 timezone show commands Displays a devices timezone Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show timezone Parameters show timezone Example wm3400-34710C8(config)#show timezone Timezone is America/Los_Angeles timezone Displays timezone where the AP or wireless controller is deployed
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 524 upgrade-status show commands Displays the last image upgrade status NOTE This command is not available in the USER EXEC Mode Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show upgrade-status {detail {on <DEVICE-NAME>}|on <DEVICE-NAME>} Parameters show upgrade-status {detail {on <DEVICE-NAME>}|on <DEVICE-NAME>} Example wm3400-34710C8(config)#show upgrade-status detail on wm3400-34710C8E Last Image Upgrade Status : Successful Last Image Upgrade Time : 2011-06-15 08:51:17 UTC wm3400-34710C8(config)# -------------------------------------------------------- Running from partition /dev/mtdblock6, partition to update is /dev/ mtdblock7 var2 is 6 percent full detail {on <DEVICE-NAME>} Displays last image upgrade log on <DEVICE-NAME> Optional. Displays last image upgrade log on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. on <DEVICE-NAME> Optional. Displays last image upgrade status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 525 /tmp is 6 percent full Free Memory 155900 kB FWU invoked via Linux shell Validating image file header Making file system Extracting files (this can take some time). Version of firmware update file is 5.3.0.0-033D Successful wm3400-34710C8(config)# wm3400-34710C8(config)#show upgrade-status on wm3400-34710C8 Last Image Upgrade Status : Successful Last Image Upgrade Time : 04:12:2010 08:44:00 UTC wm3400-34710C8(config)#
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 526 version show commands Displays a devices software and hardware version Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show version {on <DEVICE-NAME>} Parameters show version {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show version on wm3400-34710C8 WM3700 version 5.3.0.0-048B Copyright (c) 2004-2011 Extreme Networks, Inc. All rights reserved. Booted from secondary wm3400-34710C8 uptime is 3 days, 19 hours 14 minutes CPU is RMI XLR V0.4 255464 kB of on-board RAM Base ethernet MAC address is 00-15-70-37-FA-BE System serial number is 6268529900014 Model number is WM-3700-1000-WR FPGA version is 3.41 wm3400-34710C8(config)# version {on <DEVICE-NAME>} Displays software and hardware versions on all devices or a specified device on <DEVICE-NAME> Optional. Displays software and hardware versions on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller.
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 527 vrrp show commands Displays VRRP protocol details Supported on the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show vrrp [brief|details|error-stats|stats] show vrrp [brief|details|stats] {<1-255> on <DEVICE-NAME>|on <DEVICE-NAME>} show vrrp error-stats {on <DEVICE-NAME>} Parameters show vrrp [brief|details|error-stats|stats] brief {<1-255> on <DEVICE-NAME>| on <DEVICE-NAME>} Displays VRRP protocol information on a specified device <1-255> Specify the router ID on Optional. Displays brief information on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller details {<1-255> on <DEVICE-NAME>| on <DEVICE-NAME>} Displays all the VRRP protocol details on a specified device <1-255> Specify the router ID on Optional. Displays all the VRRP protocols on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller error-stats {on <DEVICE-NAME>} Displays global error statistics on a specified device on Optional. Displays global error statistics on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller stats {<1-255> on <DEVICE-NAME>|on <DEVICE-NAME>} Displays VRRP protocol related statistics on a specified device <1-255> Specify the router ID on Optional. Displays statistics on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 528 Example wm3400-34710C8(config-profile-default-wm3400)#show vrrp error-stats on wm3400-34710C8 Last protocol error reason: none IP TTL errors: 0 Version mismatch: 0 Packet Length error: 0 Checksum error: 0 Invalid virtual router id: 0 Authentication mismatch: 0 Invalid packet type: 0 wm3400-34710C8(config)#show vrrp details on wm3400-34710C8 VRRP Group 1: version 2 interface none configured priority 1 advertisement interval 1 sec preempt enable, preempt-delay 0 virtual mac address 00-00-5E-00-01-01 sync group disable wm3400-34710C8(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 529 what show commands Displays details of a specified search phrase Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show what [contains|is] <WORD> {on <DEVICE-NAME>} Parameters show what [contains|is] <WORD> {on <DEVICE-NAME>} Example wm3400-34710C8(config)#show what is help on wm3400-34710C8 ? | Output modifiers > Output redirection >> Output redirection appending <cr> wm3400-4710C8>show what is wm3400 --------------------------------------------------------------------------------------------------------- NO. CATEGORY MATCHED OTHER KEY INFO (1) OTHER KEY INFO (2) OTHER KEY INFO (3) NAME/VALUE NAME/VALUE NAME/VALUE NAME/VALUE --------------------------------------------------------------------------------------------------------- type type mac rf_domain_name 1 device-cfg wm3400 wm3400 00-04-96-47-10-C8 default --------------------------------------------------------------------------------------------------------- contains <WORD> {on <DEVICE-NAME>} Searches on all the items that contain a specified word <WORD> Specify a word to search on <DEVICE-NAME> Optional. Displays details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller is <WORD> {on <DEVICE-NAME>} Searches on an exact match <WORD> Specify a word to search on <DEVICE-NAME> Optional. Displays details on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 530 wireless show commands Displays wireless configuration parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax show wireless [ap|client|domain|mesh|radio|regulatory|sensor-server| unsanctioned|wips|wlan] show wireless ap {configured|detail|load-balancing|on <DEVICE-NAME>} show wireless ap {detail {<MAC/HOST-NAME> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE- OR-DOMAIN-NAME>} show wireless ap {load-balancing {client-capability|events|neighbors} {(on <DEVICE- NAME>)} show wireless client {associaton-history|detail|filter|on <DEVICE-OR- DOMAIN- NAME>|statistics|tspec} show wireless client {association-history <MAC> {on <DEVICE-OR-DOMAIN- NAME>}} show wireless client {detail <MAC> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE- OR- DOMAIN-NAME> show wireless client {filter {ip|on <DEVICE-OR-DOMAIN-NAME>|state|wlan}} show wireless client {filter ip [<IP>|not <IP>] {on <DEVICE-OR-DOMAIN- NAME>]} show wireless client {filter state [data-ready|not [data- ready|roaming]|roaming] {on <DEVICE-OR-DOMAIN-NAME>]} show wireless client {filter wlan [<WLAN>|not <WLAN>] {on <DEVICE-OR- DOMAIN-NAME>]} show wireless client {statistics {detail <MAC>|rf|window-data <MAC>} {(on <DEVICE-OR- DOMAIN-NAME>)}}
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 531 show wireless client {tspec <MAC> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE- OR-DOMAIN- NAME>} show wireless domain statistics {detail {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE-OR- DOMAIN-NAME>}}] show wireless mesh [detail|links {on <DEVICE-OR-DOMAIN-NAME>}] show wireless mesh detail {<DEVICE-NAME>|filter|on <DEVICE-OR-DOMAIN-NAME>} show wireless mesh detail {<DEVICE-NAME> <1-3> {(filter <RADIO-MAC>)} {(on <DEVICE- OR-DOMAIN-NAME>)} show wireless radio {detail|on <DEVICE-OR-DOMAIN-NAME>|statistics|tspec} show wireless radio {detail {<DEVICE-NAME> <1-3> (filter {on <DEVICE-OR- DOMAIN- NAME>|<RADIO-MAC>})} show wireless radio {statistics {detail|on|rf|windows-data}} show wireless radio {statistics {on <DEVICE-OR-DOMAIN-NAME>|rf {on <DEVICE- OR-DOMAIN-NAME>}} show wireless radio {statistics {detail|window-data} {<DEVICE-NAME> <1-3>} {(filter <RADIO-MAC>)} {(on <DEVICE-OR-DOMAIN-NAME>)} show wireless regulatory [channel-info <WORD>|country-code <WORD>| device-type] show wireless regulatory device-type [ap4600|ap4511|ap4700|wm3400] <WORD> show wireless sensor-server {on <DEVICE-OR-DOMAIN-NAME>} show wireless unsanctioned aps {detail|statistics} {(on <DEVICE-OR-DOMAIN- NAME>)} show wireless wips [client-blacklist|event-history]{on <DEVICE-OR-DOMAIN- NAME>} show wireless wlan {config|detail <WLAN>|on <DEVICE-OR-DOMAIN-NAME>| policy-mappings|statistics|usage-mappings} show wireless wlan {detail <WLAN>|on <DEVICE-OR-DOMAIN-NAME>|policy- mappings| usage-mappings} show wireless {config filter {device <DEVICE-NAME>|rf-domain <DOMAIN- NAME>}} show wireless wlan statitics {<WLAN>|detail|traffic} {on <DEVICE-OR-DOMAIN- NAME>} Parameters show wireless ap {configured} wireless Displays wireless configuration parameters ap Displays information on wireless controller managed access points configured Optional. Displays all configured AP information
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 532 show wireless ap {detail {<MAC/HOST-NAME> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE-OR-DOMAIN-NAME>}} show wireless ap {load-balancing {client-capability|events|neighbors} {(on <DEVICE-NAME>)}} show wireless client {association-history <MAC> {on <DEVICE-OR-DOMAIN- NAME>}} show wireless client {detail <MAC> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE- OR-DOMAIN-NAME>} wireless Displays wireless configuration parameters ap Displays information on wireless controller managed access points detail {<MAC/HOST-NAME> {on <DEVICE-OR-DOMAIN- NAME>} Optional. Displays detailed information for all APs or a specified AP <MAC/HOST-NAME> Optional. Displays information for a specified AP on <DEVICE-OR-DOMAIN-NAME> Optional. Displays information on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. on <DEVICE-OR-DOMAIN- NAME>} Optional. Displays information on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters ap Displays information on wireless controller managed access points load-balancing {client-capability| events|neighbors} Optional. Displays load balancing status. Use additional filters to view specific details. client capability Optional. Displays client band capability events Optional. Displays client events neighbors Optional. Displays neighboring clients on <DEVICE-NAME> The following are common to the client capability, events, and neighbors parameters: on Optional. Displays load balancing status on a specified device <DEVICE-NAME> Specify the name of the AP or wireless controller. wireless Displays wireless configuration parameters client Displays client information based on the parameters passed association-history <MAC> Optional. Displays association history for a specified client <MAC> Specify the MAC address of the client. on <DEVICE-OR-DOMAIN- NAME> Optional. Displays association history on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters client Displays client information based on the parameters passed
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 533 show wireless client {filter ip {<IP>|not <IP>} {on <DEVICE-OR-DOMAIN- NAME>} show wireless client {filter state {data-ready|not {data- ready|roaming}|roaming} {on <DEVICE-OR-DOMAIN-NAME>} show wireless client {filter wlan {<WLAN>|not {WLAN} {on <DEVICE-OR-DOMAIN- NAME>} detail <MAC> {on <DEVICE-OR-DOMAIN- NAME>} Optional. Displays detailed information for a specified client <MAC> Specify the MAC address of the client. on <DEVICE-OR-DOMAIN-NAME> Optional. Displays detailed information on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. on <DEVICE-OR-DOMAIN- NAME> Optional. Displays client information on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters client Displays client information based on the parameters passed filter IP {<IP>|not <IP>} Optional. Uses IP address to filter clients <IP> Optional. Selects clients based on the IP address passed not <IP> Optional. Inverts the match selection on <DEVICE-OR-DOMAIN- NAME> The following is common to the IP and not IP parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays association history on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters client Displays client information based on the parameters passed filter state {data-ready| not {data-ready|roaming}| roaming} Optional. Filters clients based on their state data-ready Optional. Selects wireless clients in the data-ready state not {data-ready|roaming} Optional. Inverts match selection. Selects wireless clients neither ready nor roaming Roaming Optional. Selects roaming clients on <DEVICE-OR-DOMAIN- NAME> The following is common to the ready, not, and roaming parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays client details on a specified device or RF Domain wireless Displays wireless configuration parameters client Displays client information based on the parameters passed filter wlan {<WLAN>| not <WLAN>} Optional. Filters clients on a specified WLAN <WLAN> Specify the WLAN name. not <WLAN> Inverts the match selection
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 534 show wireless client {statistics {detail <MAC>|rf|window-data <mac>} {on <DEVICE-OR-DOMAIN-NAME>} show wireless client {tspec {<MAC> {on <DEVICE-OR-DOMAIN-NAME>}|on <DEVICE- OR-DOMAIN-NAME>}} show wireless mesh links {on <DEVICE-OR-DOMAIN-NAME>} show wireless mesh detail {<DEVICE-NAME> <1-3> {(filter <RADIO-MAC>)} {(on <DEVICE-OR-DOMAIN-NAME>)}} on <DEVICE-OR-DOMAIN- NAME> The following are common to the WLAN and not parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Filters clients on a specified device or RF Domain wireless Displays wireless configuration parameters client Displays client information based on the parameters passed statistics {detail <MAC>| rf|window-data <MAC>} Optional. Displays detailed client statistics. Use additional filters to view specific details. detail <MAC> Optional. Displays detailed statistics for a specified client <MAC> Specify the MAC address of the client. rf Displays detailed client statistics on a specified device or RF Domain window-data <MAC> Displays historical data, for a specified client <MAC> Specify the MAC address of the client on <DEVICE-OR-DOMAIN- NAME> The following are common to the detail <MAC>, RF, and window-data <MAC> parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays client statistics on a specified device or RF Domain wireless Displays wireless configuration parameters client Displays client information based on the parameters passed tspec <MAC> {on <DEVICE-OR-DOMAIN- NAME>} Optional. Displays detailed TSPEC information for all clients or a specified client <MAC> Optional. Displays detailed TSPEC information for a specified client <MAC> Specify the MAC address of the client. on <DEVICE-OR-DOMAIN-NAME> Optional. Displays detailed TSPEC information on a specified device or RF Domain on <DEVICE-OR-DOMAIN- NAME> Optional. Displays detailed TSPEC information for all wireless clients on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters mesh Displays information on radio mesh links {on <DEVICE-OR-DOMAIN- NAME>} Optional. Displays active links of a radio mesh on <DEVICE-OR-DOMAIN-NAME> Optional. Displays active links of a radio mesh on a specified device or RF Domain wireless Displays wireless configuration parameters mesh Displays radio mesh information
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 535 show wireless radio {detail {<DEVICE-NAME> <1-3> {(filter <RADIO-MAC>)} {(on <DEVICE-OR-DOMAIN-NAME>)}} show wireless radio {statistics {on <DEVICE-OR-DOMAIN-NAME>|rf {on <DEVICE- OR-DOMAIN-NAME>}} show wireless radio {statistics {detail|window-data} {<DEVICE-NAME> <1-3> {(filter <RADIO-MAC>)} {(on <DEVICE-OR-DOMAIN-NAME>)}} detail Optional. Displays detailed radio mesh information <DEVICE-NAME> <1-3> Optional. Specify the MAC address or hostname, or append the interface number to form the mesh ID in the AA-BB-CC-DD-EE-FF:RX or HOSTNAME:RX format. <1-3> Optional. Specify the mesh interface index. filter <RADIO-MAC> Optional. Provides additional filters <RADIO-MAC> Optional. Filters based on the radio MAC address on <DEVICE-OR-DOMAIN- NAME> Optional. After specifying the radio MAC address, further refine the search by specifying a device or RF Domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters radio Displays radio operation status and other related information detail Optional. Displays detailed radio operation status <DEVICE-NAME> <1-3> Optional. Specify the MAC address or hostname, or append the interface number to form the radio ID in the AA-BB-CC-DD-EE-FF:RX or HOSTNAME:RX format. <1-3> Optional. Specify the radio interface index. filter <RADIO-MAC> Optional. Provides additional filters <RADIO-MAC> Optional. Filters based on the radio MAC address on <DEVICE-OR-DOMAIN- NAME> Optional. After specifying the radio MAC address, further refine the search by specifying a device or RF Domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters radio Displays radio operation status and other related information statistics {on <DEVICE-OR-DOMIAN- NAME>| rf {on <DEVICE-OR-DOMAIN- NAME>}} Optional. Displays radio traffic and RF statistics on <DEVICE-OR-DOMIAN-NAME> Optional. Displays traffic and RF related statistics on a specified device or RF Domain <DEVICE-OR-DOMIAN-NAME> Specify the name of the AP, wireless controller, or RF Domain. rf Optional. Displays RF statistics on a specified device or RF Domain <DEVICE-OR-DOMIAN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters radio Displays radio operation status and other related information
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 536 show wireless regulatory [channel-info <WORD>|county-code <WORD>] show wireless regulatory device-type [ap4600|ap4511|ap4700|wm3400] <WORD> show wireless sensor-server {on <DEVICE-OR-DOMAIN-NAME>} statistics {detail|window-data} Optional. Displays radio traffic and RF statistics. Use additional filters to view specific details. The options are: are: detail Displays detailed traffic and RF statistics of all radios window-data Displays historical data over a time window <DEVICE-NAME> <1-3> The following are common to the detail and window-data parameters: <DEVICE-NAME> Optional. Specify the MAC address or hostname, or append the interface number to form the radio ID in the AA-BB-CC-DD-EE- FF:RX or HOSTNAME:RX format. <1-3> Optional. Specify the radio interface index. filter <RADIO-MAC> Optional. Provides additional filters <RADIO-MAC> Optional. Filters based on the radio MAC address on <DEVICE-OR-DOMAIN- NAME> Optional. After specifying the radio MAC address, further refine the search by specifying a device or RF Domain. <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters regulatory Displays wireless regulatory information channel-info <WORD> Displays channel information <WORD> Specify the channel number. country-code <WORD> Displays country code to country name information <WORD> Specify the two letter ISO-3166 country code. wireless Displays wireless configuration parameters regulatory Displays wireless regulatory information device-type [ap4600|ap4511|ap4700| wm3400] <WORD> Displays regulatory information based on the device type ap4600 Displays AP4600 information ap4511 Displays AP4511 information ap4700 Displays AP4700 information wm3400 Displays WM3400 information The following is common to all of the above: <WORD> Specify the two letter ISO-3166 country code. wireless Displays wireless configuration parameters sensor- server {on <DEVICE-OR-DOMAIN- NAME>} Displays AirDefense sensor server configuration details on <DEVICE-OR-DOMAIN-NAME> Optional. Displays AirDefense sensor server configuration on a specified device or RF Domain
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 537 show wireless unsanctioned aps {detailed|statistics} {(on <DEVICE-OR- DOMAIN-NAME>)} show wireless wips [client-blacklist|event-history] {on <DEVICE-OR-DOMAIN- NAME>} show wlan {detail <WLAN>|on <DEVICE-OR-DOMAIN-NAME>|policy-mappings|usage- mappings} show wlan {config filter {device <DEVICE-NAME>|rf-domain <DOMAIN-NAME>} show wlan {statistics {<WLAN>|detail} {(on <DEVICE-OR-DOMAIN-NAME>)} wireless Displays wireless configuration parameters unsanctioned aps Displays unauthorized APs. Use additional filters to view specific details. detailed Optional. Displays detailed unauthorized APs information statistics Optional. Displays channel statistics on <DEVICE-OR-DOMAIN- NAME> The following is common to the detailed and statistics parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters wips [client-blacklist|event- history] Displays the WIPS details client-blacklist Displays blacklisted clients event-history Displays event history on <DEVICE-OR-DOMAIN- NAME> The following are common to the client-blacklist and event-history parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Specify the name of the AP, wireless controller, or RF Domain. wireless Displays wireless configuration parameters wlan Displays WLAN related information based on the parameters passed detail <WLAN> Optional. Displays WLAN configuration <WLAN> Specify the WLAN name. on <DEVICE-OR-DOMAIN- NAME> Optional. Displays WLAN configuration on a specified device or RF Domain <DEVICE-OR-DOMAIN-NAME> Specify the name of the AP, wireless controller, or RF Domain. policy-mappings Optional. Displays WLAN policy mappings usage-mappings Optional. Lists all devices and profiles using the WLAN wireless Displays wireless configuration parameters wlan Displays WLAN related information based on the parameters passed config filter Optional. Filters WLAN information based on the device name or RF Domain device <DEVICE-NAME> Optional. Filters WLAN information based on the device name <DEVICE-NAME> Specify the device name. rf-domain <DOMAIN-NAME> Optional. Filters WLAN information based on the RF Domain <DOMAIN-NAME> Specify the RF Domain name. wireless Displays wireless configuration parameters
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 538 Example wm3400-34710C8(config)#show wireless sensor server status on ap4700-889EC4 wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless unauthorized aps detailed Number of APs seen: 1 wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless wips mu-blacklist No mobile units blacklisted wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless wlan config +-----------+---------+-----------+-------------+-----------------+------- | NAME | ENABLE | SSID | ENCRYPTION | AUTHENTICATION | VLAN | +-----------+---------+-----------+-------------+-----------------+------- | test | Y | test | none | none | 1 | | wlan1 | Y | wlan1 | none | none | 1 | wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless wlan statistics +---------------------+----------+----------+--------+--------+--------+-- | WLAN | TX BYTES | RX BYTES |TX PKTS |RX PKTS |TX KBPS |RX KBPS |DROPPED | ERRORS | +---------------------+----------+----------+--------+--------+--------+- | wlan1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +---------------------+----------+----------+--------+--------+--------+-- Total number of wlan displayed: 2 wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless regulatory channel-info 1 Center frequency for channel 1 is 2412MHz wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless regulatory country-code ISO CODE NAME ------------------------------------------------------------ al Algeria ai Anguilla ar Argentina au Australia at Austria wlan Displays WLAN related information based on the parameters passed statistics {<WLAN>|detail} Optional. Displays WLAN statistics. Use additional filters to view specific details <WLAN> Optional. Displays WLAN statistics. Specify the WLAN name. detail Optional. Displays detailed WLAN statistics on <DEVICE-OR-DOMAIN- NAME> The following is common to the <WLAN> and detail parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays WLAN statistics on a specified device or RF Domain
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 539 bs Bahamas bh Bahrain bb Barbados by Belarus be Belgium bm Bermuda bo Bolivia bw Botswana ba Bosnia-Herzegovina br Brazil bg Bulgaria ca Canada ky Cayman Islands ...................................................... wm3400-34710C8(config)# wm3400-34710C8(config)#show wireless regulatory device-type ap4600 in -------------------------------------------------------------------------- # Channel Set Power(mW) Power (dBm) Placement DFS CAC(mins) -------------------------------------------------------------------------- 1 1-13 4000 36 Indoor/Outdoor NA NA 2 36-64 200 23 Indoor Not Required 0 3 149-165 1000 30 Outdoor Not Required 0 4 149-165 200 23 Indoor Not Required 0 -------------------------------------------------------------------------- wm3400-34710C8(config)# WM3400-880DA7(config)#show wireless ap detail WM3400-880DA7 on WM3400- 880DA7 AP: 00-23-68-88-0D-A7 AP Name : WM3400-880DA7 Location : default RF-Domain : default Type : WM3400 Model : WM-3400-11110-US Num of radios : 2 Num of clients : 0 Last Smart-RF time : not done Stats update mode : auto Stats interval : 6 Radio Modes : radio-1 : wlan radio-2 : wlan Country-code : not-set Site-Survivable : True Last error : Fault Detected : False WM3400-880DA7(config)# WM3400-880DA7(config)#show wireless ap load-balancing on default/WM3400- 880DA7
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 540 AP: 00-23-68-88-0D-A7 Client requests on 5ghz : allowed Client requests on 2.4ghz : allowed Average AP load in neighborhood : 0 % Load on this AP : 0 % Total 2.4ghz band load in neighborhood : 0 % Total 5ghz band load in neighborhood : 0 % Configured band ratio 2.4ghz to 5ghz : 1:1 Current band ratio 2.4ghz to 5ghz : 0:0 Average 2.4ghz channel load in neighborhood : 0 % Average 5ghz channel load in neighborhood : 0 % Load on this AP's 2.4ghz channel : 0 % Load on this AP's 5ghz channel : 0 % Total number of APs displayed: 1 WM3400-880DA7(config)# WM3400-880DA7(config)#show wireless ap on default -------------------------------------------------------------------------- MODE : radio modes - W = WLAN, S=Sensor, ' ' (Space) = radio not present -------------------------------------------------------------------------- AP-NAME AP-LOCATION RF-DOMAIN AP-MAC #RADIOS MODE #CLIENT LAST-CAL-TIME -------------------------------------------------------------------------- WM3400-880DA7 default default 00-23-68-88-0D-A7 2 W-W 0 not done -------------------------------------------------------------------------- Total number of APs displayed: 1 WM3400-880DA7(config)#
show commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 541 wwan show commands Displays wireless WAN status Supported on the following platforms: WM3400 WM3600 Syntax show wwan [configuration|status] {on <DEVICE-OR-DOMAIN-NAME>} Parameters show wwan [configuration|status] {on <DEVICE-OR-DOMAIN-NAME>} Example WM3400-880DA7(con fig-device-00-23-68-88-0D-A7)*#show wwan configuration on wm3400-880DA7 >>> WWAN Configuration: +------------------------------------------- | Access Port Name : isp.cingular | User Name : testuser | Cryptomap : map1 +------------------------------------------- WM3400-880DA7(config-device-00-23-68-88-0D-A7)# WM3400-880DA7(config-device-00-23-68-88-0D-A7)#show wwan status on wm3400- 880DA7 >>> WWAN Status: +------------------------------------------- | State : ACTIVE | DNS1 : 209.183.54.151 | DNS2 : 209.183.54.151 +------------------------------------------- WM3400-880DA7(config-device-00-23-68-88-0D-A7)# wwan Displays wireless WAN configuration and status details configuration Displays wireless WAN configuration information status Displays wireless WAN status information on <DEVICE-OR-DOMAIN- NAME> The following are common to the configuration and status parameters: on <DEVICE-OR-DOMAIN-NAME> Optional. Displays configuration or status details on a specified device or RF Domain
Chapter 7: Show Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 542
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 543 C H A P T E R 8 Profiles Profiles enable administrators to assign a common set of configuration parameters and policies to wireless controllers and access points. Profiles can be used to assign common or unique network, wireless and security parameters to wireless controller and access points across a large, multi segment site. The configuration parameters within a profile are based on the hardware model the profile was created to support. The wireless controller supports both default and user defined profiles implementing new features or updating existing parameters to groups of wireless controller or access points. The central benefit of a profile is its ability to update devices collectively without having to modify individual device configurations. The system maintains a couple of default profiles. The default profile is applied to the wireless controller automatically, and default AP profiles are applied to the APs automatically discovered by the wireless controller. After adoption, if a change is made in one of the parameters in the profile, that change is reflected across all the APs using the same profile. User defined profiles are manually created for each supported wireless controller and access point model. User defined profiles can be manually assigned or automatically assigned to access points. AP4600 Adds an AP4600 access point profile AP4731 Adds an AP4731 access point profile WM3400 Adds an WM3400 wireless controller profile WM3600 Adds an WM3600 wireless controller profile WM3700 Adds an WM3700 wireless controller profile Each default and user defined profile contains policies and configuration parameters. Changes made to these parameters are automatically inherited by the devices assigned to the profile. wm3400-34710C8(config)#profile WM3700 default-WM3700 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config)#profile AP4731 default-AP4731 wm3400-34710C8(config-profile-default-AP4731)# Creating Profiles
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 544 NOTE The commands present under Profiles are also available under the Device mode. The additional commands specific to the Device mode are listed separately. Refer Chapter 7, <$elemtextDevice Specific Commands for more information. The following table summarizes profile commands Command Description Reference ap-upgrade Enables automatic AP firmware upgrade page 8-546 arp Configures static address resolution protocol page 8-548 auto-learn- staging-config Enables network configuration learning of devices page 8-550 autoinstall Configures the automatic install feature page 8-551 bridge Configures bridge specific commands page 8-553 cdp Enables Cisco Discovery Protocol (CDP) on a device page 8-568 cluster Configures a cluster name page 8-570 configuration- persistence Enables persistence of configuration across reloads page 8-573 controller Configures a wireless controller page 8-575 critical-resource Monitors user configured IP addresses and logs their status page 8-577 crypto Configures crypto settings page 8-579 dscp-mapping Configures an IP DSCP to 802.1p priority mapping for untagged frames page 8-613 email-notification Configures e-mail notification page 8-614 enforce-version Checks device firmware versions before attempting connection page 8-617 events Displays system event messages page 8-619 interface Configures an interface page 8-631 ip Configures IP components page 8-620 l2tpv3 Defines the Layer 2 Tunnel Protocol (L2TP) protocol for tunneling Layer 2 payloads using Virtual Private Networks (VPNs) page 8-625 led Turns device LEDs on or off page 8-669 legacy-auto- downgrade Auto downgrades a legacy device firmware page 8-670 legacy-auto- update Auto upgrades a legacy device firmware page 8-671 lldp Configures Link Layer Discovery Protocol (LLDP) page 8-672 load-balancing Configures load balancing parameters page 8-674 logging Modifies message logging page 8-679 mac-address- table Configures the MAC address table page 8-681 mint Configures MiNT protocol page 8-683 misconfiguration- recovery-time Verifies wireless controller connectivity after a configuration is received page 8-687 monitor Enables critical resource monitoring page 8-688 neighbor- inactivity-timeout Configures neighbor inactivity timeout page 8-690
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 545 neighbor-info- interval Configures neighbor information exchange interval page 8-691 no Negates a command or sets its default values page 8-692 noc Configures NOC settings page 8-695 ntp Configures an NTP server page 8-696 power-config Configures the power mode page 8-700 preferred- controller-group Specifies the wireless controller group preferred for adoption page 8-698 preferred-tunnel- controller Configures the tunnel controller name which the system prefers for tunneling extended vlan traffic page 8-699 radius Configures device-level RADIUS authentication parameters page 8-702 router Configures dynamic router protocol settings page 8-703 rf-domain- manager Enables RF Domain manager page 8-705 spanning-tree Configures spanning tree commands page 8-706 tunnel-controller Configures the name of tunneled-wlan (extended-vlan) controller page 8-710 use Uses pre configured policies with this profile page 8-711 vrrp Configures Virtual Router Redundancy Protocol (VRRP) group settings page 8-714 wep-shared-key- auth Enables support for 802.11 WEP shared key authentication page 8-718 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 546 ap-upgrade Creating Profiles Enables an automatic firmware upgrade on an adopted access point Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap-upgrade [auto|count] ap-upgrade auto {(ap4021|ap4600|ap4511|ap4521|ap4532|ap4700)} ap-upgrade count <1-20> Parameters ap-upgrade auto {(ap4021|ap4600|ap4511|ap4521|ap4532|ap4700)} ap-upgrade count <1-20> auto Enables automatic firmware upgrade on an adopted AP ap4021 Optional. Enables automatic AP4021 firmware upgrade ap4600 Optional. Enables automatic AP4600 firmware upgrade ap4511 Optional. Enables automatic AP4511 firmware upgrade ap4521 Optional. Enables automatic AP4521 firmware upgrade ap4532 Optional. Enables automatic AP4532 firmware upgrade ap4700 Optional. Enables automatic AP4700 firmware upgrade count <1-20> Sets a limit to the number of concurrent upgrades performed <1-20> Specify a value from 1 - 20.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 547 Example wm3400-34710C8(config-profile-default-WM3700)#ap-upgrade count 7 wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 548 arp Creating Profiles Configures Address Resolution Protocol (ARP) parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax arp [<IP>|timeout] arp <IP> <MAC> arpa [<L3-INTERFACE-NAME>|vlan <1-4094>] {dhcp-server|router} arp timeout <TIME> Parameters arp <IP> <MAC> arpa [<L3-INTERFACE-NAME>|vlan <1-4094>] {dhcp-server|router} arp timeout <TIME> arp <IP> Configures a static ARP entry for a IPv4 IP address <IP> Specify the static IP address. <MAC> Specify the MAC address associated with the IP and the Switch Virtual Interface (SVI). arpa Sets ARP type to ARPA <L3-INTERFACE-NAME> Sets the router interface name <L3-INTERFACE-NAME> Specify a name of the router interface. vlan <1-4094> Sets a VLAN interface <1-4094> Specify a SVI VLAN ID from 1 - 4094. {dhcp-server|router} The following are common for the router and VLAN parameters: dhcp-server Optional. Sets the ARP entry for the DHCP server router Optional. Sets the ARP entry for a router arp timeout <TIME> Sets ARP timeout <TIME> Sets the ARP entry timeout in seconds. Specify a value from 15 - 86400 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 549 Example wm3400-34710C8(config-profile-default-WM3700)#arp timeout 2000 wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 arp timeout 2000 no autoinstall configuration no autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p wm3400-34710C8(config-profile-default-WM3700)#arp 172.16.10.10 45-bc-22-38-16-3F arpa vlan 3 dhcp-server Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 550 auto-learn-staging-config Creating Profiles Enables automatic recognition of devices pending adoption Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax auto-learn-staging-config Parameters None Example wm3400-34710C8(config-profile-default-WM3700)#auto-learn-staging-config wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 551 autoinstall Creating Profiles Automatically installs firmware image and configuration parameters on to the selected device. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax autoinstall [configuration|firmware] Parameters autoinstall [configuration|firmware] Example wm3400-34710C8(config-profile-default-WM3700)#autoinstall configuration wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#autoinstall firmware wm3400-34710C8(config-profile-default-WM3700)# Related Commands configuration Autoinstalls configuration parameters. Setup parameters are automatically configured on devices using this profile firmware Autoinstalls firmware image. Firmware images are automatically installed on devices using this profile no Disables or reverts settings to their default
TM 4000 Series Access Point CLI Reference Guide 553 bridge bridge commands Configures VLAN Ethernet bridging parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 NOTE The interfaces mentioned below are supported as follows: ge <index> WM3700 and WM3400 supports 4 GEs, WM3600 supports 8 GEs me1 Only supported on WM3700 and WM3600 Syntax bridge vlan <1-4095> Parameters bridge vlan <1-4095> Usage Guidelines Creating customized filter schemes for bridged networks limits the amount of unnecessary traffic processed and distributed by the bridging equipment. If a bridge does not hear Bridge Protocol Data Units (BPDUs) from the root bridge within the specified interval, defined in the max-age (seconds) parameter, assume the network has changed and recomputed the spanning-tree topology. Example wm3400-34710C8(config-profile-default-WM3700)#bridge vlan 5 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-5)# vlan <1-4095> Specify a VLAN index from 1 - 4095.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 554 bridge-vlan-mode commands bridge commands The following table summarizes bridge VLAN mode commands Command Description Reference bridging-mode Configures how packets on this VLAN are bridged page 8-555 description Defines VLAN description page 8-557 edge-vlan Enables edge VLAN mode page 8-558 ip Configures IP components page 8-620 no Negates a command or sets its default values page 8-562 stateful-packet- inspection-12 Enables stateful packet inspection in the layer 2 firewall page 8-566 use Uses pre configured access lists with this PF bridge policy page 8-567 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 555 bridging-mode bridge-vlan-mode commands Configures how packets are bridged on the selected VLAN Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax bridging-mode [auto|isolated-tunnel|local|tunnel] Parameters bridging-mode [auto|isolated-tunnel|local|tunnel] Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#bridging-mode isolated- tunnel wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1) wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#show context bridge vlan 1 bridging-mode isolated-tunnel ip igmp snooping ip igmp snooping querier wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# bridging-mode Configures VLAN bridging modes auto Automatically selects the bridging mode to match the WLAN, VLAN and bridging mode configurations isolated-tunnel Bridges packets between local Ethernet ports and local radios, and passes tunneled packets through without de tunneling local Bridges packets normally between local Ethernet ports and local radios (if any) tunnel Bridges packets between local Ethernet ports, local radios, and tunnels to other APs and wireless controllers
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 556 Related Commands no Disables or reverts VLAN Ethernet bridge settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 557 description bridge-vlan-mode commands Sets a VLAN bridge description Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax description <WORD> Parameters description <WORD> Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#description This is a description for the bridged VLAN wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#show context bridge vlan 1 description This\ is\ a\ description\ for\ the\ bridged\ VLAN bridging-mode isolated-tunnel ip igmp snooping ip igmp snooping querier Related Commands description <WORD> Sets a VLAN bridge description <WORD> Specify a VLAN description. no Disables or reverts VLAN Ethernet bridge settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 558 edge-vlan bridge-vlan-mode commands Enables edge VLAN mode. In the edge VLAN mode, a protected port does not forward traffic to another protected port on the same wireless controller. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax edge-vlan Parameters None Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#edge-vlan wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# Related Commands no Disables or reverts VLAN Ethernet bridging settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 559 ip bridge-vlan-mode commands Configures VLAN bridge IP components Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [arp|dhcp|igmp] ip [arp|dhcp] trust ip igmp snooping {mrouter|querier|unknown-multicast-fwd} ip igmp snooping {mrouter [interface <INTERFACE>|learn pim-dvmrp]} ip igmp snooping {querier {address <IP>|max-response-time <1-25>| timer expiry <60-300>|version <1-3>}} Parameters ip [arp|dhcp] trust ip igmp snooping {unknown-multicast-fwd} ip Configures VLAN bridge IP parameters arp trust Configures the ARP trust parameter trust Trusts ARP responses on the VLAN dhcp trust Configures the DHCP trust parameter trust Trusts DHCP responses on the VLAN ip Configures VLAN bridge IP parameters igmp snooping Configures IGMP snooping parameter unknown-multicast-fwd Optional. Enables forwarding of unknown multicast packets
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 560 ip igmp snooping {mrouter [interface <INTERFACE>|learn pim-dvmrp]} ip igmp snooping {querier {address <IP>|max-response-time <1-25>| timer expiry <60-300>|version <1-3>}} Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip arp trust wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip dhcp trust wm3400-34710C8config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip igmp snooping mr outer interface ge1 ge2 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip igmp snooping mr outer learn pim-dvmrp wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip igmp snooping qu erier max-response-time 24 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip igmp snooping qu erier timer expiry 100 ip Configures VLAN bridge IP parameters igmp snooping Configures IGMP snooping parameters mrouter Optional. Configures multicast router parameters interface <INTERFACE> Configures multicast router interfaces <WORD> Specify a comma-separated list of interface names. learn pim-dvmrp Configures multicast router learning protocols pim-dvmrp Enables Protocol-Independent Multicast (PIM) and Distance-Vector Multicast Routing Protocol (DVMRP) snooping of packets ip Configures VLAN bridge IP parameters igmp snooping Configures IGMP snooping parameters querier Optional. Configures IGMP querier parameters address <IP> Optional. Configures IGMP querier source IP address <IP> Specify the IGMP querier source IP address. max-response-time <1-25> Optional. Configures IGMP querier maximum response time <1-25> Specify a maximum response time from 1 - 25 seconds. timer expiry <60-300> Optional. Configures IGMP querier timeout expiry Configures IGMP querier timeout <60-300> Specify the IGMP querier timeout from 60 - 300 seconds. version <1-3> Optional. Configures the IGMP version <1-3> Specify the IGMP version. The versions are 1- 3.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 561 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#ip igmp snooping qu erier version 2 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# bridge vlan 1 description This\ is\ a\ description\ of\ the\ bridged\ VLAN ip arp trust ip dhcp trust ip igmp snooping ip igmp snooping querier ip igmp snooping querier version 2 ip igmp snooping querier max-response-time 24 ip igmp snooping querier timer expiry 100 ip igmp snooping mrouter interface ge2 ge1 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# Related Commands no Disables or reverts VLAN Ethernet bridge settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 562 no bridge-vlan-mode commands Negates a command or reverts settings to their default. The no command, when used in the bridge VLAN mode, negates the VLAN bridge settings or reverts them to their default. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [bridging-mode|description|edge-vlan|ip|stateful-packet-inspection-l2|use] no ip [arp|dhcp|igmp] no ip [arp|dhcp] trust no ip igmp snooping {mrouter|querier|unknown-multicast-fwd} no ip igmp snooping {mrouter {interface <INTERFACE>|learn pin-dvmrp}} no ip igmp snooping {querier {address|max-response-time|timer expiry|version}} no use [ip-access-list|mac-access-list] tunnel out Parameters no [bridging-mode|description|edge-vlan|stateful-packet-inspection-12] no ip [arp|dhcp] trust no bridging-mode Resets bridging mode to auto no description Removes VLAN description no edge-vlan Disables edge VLAN mode no stateful-packet- inspection-12 Disables stateful packet inspection in the layer 2 firewall no ip Negates or reverts VLAN bridge IP settings arp trust Disables trust of ARP responses on the VLAN dhcp trust Disables trust of DHCP responses on the VLAN
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 563 no ip igmp snooping {unknown-multicast-fwd} no ip igmp snooping {mrouter [interface <INTERFACE>|learn pim-dvmrp]} no ip igmp snooping {querier {address|max-response-time| timer expiry|version}} no use [ap-access-list|mac-access-list] tunnel out no ip Negates or reverts VLAN bridge IP settings igmp snooping Negates or reverts IGMP snooping settings unknown-multicast-fwd Optional. Disables the forwarding of unknown multicast packets no ip Negates or reverts VLAN bridge IP settings igmp snooping Negates or reverts IGMP snooping settings mrouter Optional. Resets or disables multicast router parameters interface <INTERFACE> Disables mrouter interfaces <WORD> Specify interface names, separated by a space. learn pim-dvmrp Disables multicast router learning protocols pim-dvmrp Disables PIM-DVMRP snooping of packets no ip Negates or reverts VLAN bridge IP settings igmp snooping Configures IGMP snooping components querier Optional. Reverts IGMP querier settings address Optional. Reverts to the default IGMP querier source IP address of 0.0.0.0 max-response-time Optional. Reverts to the default IGMP querier maximum response time timer expiry Optional. Reverts to the default IGMP querier timeout version <1-3> Optional. Reverts to the default IGMP version no use Removes the VLAN bridges IP access list or MAC access list ip-access-list tunnel out Removes the VLAN bridges IP access list tunnel Removes IP access list from being applied to all packets going into a tunnel out Removes IP access list from being applied to all outgoing packets mac-access-list tunnel out Removes the VLAN bridges MAC access list tunnel Removes MAC access list from being applied to all packets going into a tunnel out Removes MAC access list from being applied to all outgoing packets
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 564 Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#no description wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#no ip igmp snooping mrouter interface ge1 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#no ip igmp snooping mrouter learn pim-dvmrp wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#no ip igmp snooping querier max-response-time wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#no ip igmp querier version wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#show context bridge vlan 1 no edge-vlan no stateful-packet-inspection-l2 ip igmp snooping no ip igmp snooping unknown-multicast-fwd no ip igmp snooping mrouter learn pim-dvmrp ip igmp snooping querier wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# Related Commands bridging-mode Configures how packets on this VLAN are bridged description Defines VLAN description edge-vlan Enables edge VLAN mode ip Configures IP components no Negates a command or sets its default values stateful-packet- inspection-12 Enables stateful packet inspection in the layer 2 firewall use Uses pre configured access lists with this PF bridge policy clrscr Clears the display screen commit Commits (saves) changes made in the current session do Runs commands from EXEC mode end Ends and exits the current mode and moves to the PRIV EXEC mode exit Ends the current mode and moves to the previous mode help Displays interactive help system revert Reverts changes to their last saved configuration service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations show Displays running system information
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 565 write Writes information to memory or terminal
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 566 stateful-packet-inspection-12 bridge-vlan-mode commands Enables a stateful packet inspection at the layer 2 firewall Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax stateful-packet-inspection-l2 Parameters None Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#stateful-packet-ins inspection-l2 wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# Related Commands no Disables or reverts VLAN Ethernet bridge settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 567 use bridge-vlan-mode commands Uses pre configured access lists with this bridge policy Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [ip-access-list|mac-access-list] tunnel out <IP/MAC-ACCESS-LIST> Parameters use [ip-access-list|mac-acces-list] tunnel out <IP/MAC-ACCESS-LIST> Example wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)#use ip-access-list ext-vlan out test wm3400-34710C8(config-profile default-WM3700-bridge-vlan-1)# Related Commands use Sets this VLAN bridge policy to use an IP access list or a MAC access list ip-access-list tunnel Uses an IP access list mac-access-list Uses a MAC access list tunnel out <IP/MAC-ACCESS-LIST> The following are common to the IP access list and MAC access list parameters: tunnel Applies IP access list or MAC access list to all packets going into the tunnel out Applies IP access list or MAC access list to all outgoing packets <IP/MAC-ACCESS-LIST> Specify the IP access list or MAC access list name. no Disables or reverts VLAN Ethernet bridge settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 568 cdp Creating Profiles Uses Cisco Discovery Protocol (CDP) on the device. CDP is a layer 2 protocol to discover information about neighboring network devices Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cdp [holdtime|run|timer] cdp [holdtime <10-1800>|run|timer <5-900>] Parameters cdp [holdtime <10-1800>|run|timer <5-900>] Example wm3400-34710C8(config-profile-default-WM3700)#cdp run wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)# holdtime 1000 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)# timer 900 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 bridge vlan 1 holdtime <10-1800> Specifies the holdtime after which transmitted packets are discarded <10-1800> Specify a value from 10 - 1800 seconds. run Enables CDP sniffing and transmit globally timer <5-900> Specifies time between advertisements <5-900> Specify a value from 5 - 900 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 569 ip igmp snooping no ip igmp snooping unknown-multicast-fwd no ip igmp snooping mrouter learn pim-dvmrp ip dhcp trust holdtime 1000 timer 900 service pm sys-restart wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 570 cluster Creating Profiles Sets the cluster configuration Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cluster [force-configured-state|force-configured-state-delay|handle-stp| master-priority|member|mode|name] cluster [force-configured-state|force-configured-state-delay <3-1800>|handle-stp| master-priority <1-255>] cluster member [ip <IP> {level [1|2]}|vlan <1-4094>] cluster mode [active|standby] cluster name <CLUSTER-NAME> Parameters cluster [force-configured-state|force-configured-state-delay <3-1800>|handle-stp| master-priority <1-255>] force-configured-state Forces adopted APs to auto revert when a failed controller in a cluster restarts When a controller in the cluster fails, a secondary controller or a set of controllers manages the APs adopted by the failed controller. When force- configured-state is set and a failed controller restarts APs that were adopted by it and taken over by secondary controllers, are moved back. force-configured-state- delay <3-1800> Forces cluster transition to the configured state after a specified interval <3-1800> Specify a delay from 3 - 1800 minutes. The default is 5 minutes handle-stp Configures Spanning Tree Protocol (STP) convergence handling master-priority <1-255> Configures cluster master priority <1-255> Specifies priority for cluster master election. Assign a value from 1 - 255. Higher values have higher precedence.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 571 cluster member [ip <IP> {level [1|2]}|vlan <1-4094>] cluster mode [active|standby] cluster name <CLUSTER-NAME> Example wm3400-34710C8(config-profile-default-WM3700)#cluster name cluster1 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#cluster member ip 172.16.10.3 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#cluster mode active wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 bridge vlan 1 description Vlan1 ............................................. cluster name cluster1 cluster member ip 172.16.10.3 cluster member vlan 1 wm3400-34710C8(config-profile-default-WM3700)#cluster auto-revert-delay 10 wm3400-34710C8(config-profile-default-WM3700)# member Adds a member to the cluster. It also configures the cluster VLAN where members can be reached. ip <IP> level [1|2] Adds IP address of the new cluster member <IP> Specify the IP address. level Optional. Configures routing level for the new member. Select one of the following routing levels: 1 Level 1, local routing 2 Level 2, In-site routing vlan <1-4094> Configures the cluster VLAN where members can be reached <1-4094> Specify the VLAN ID from 1- 4094. mode [active|standby] Configures cluster mode as either active or standby active Configures the active mode standby Configures the standby mode name <CLUSTER-NAME> Configures the cluster name <CLUSTER-NAME> Specify the cluster name.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 572 Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 573 configuration-persistence Creating Profiles Enables configuration persistence across reloads Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax configuration-persistence {secure} Parameters configuration-persistence {secure} Example wm3400-34710C8(config-profile-default-WM3700)#configuration-persistence secure wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 bridge vlan 1 no edge-vlan ip igmp snooping no ip igmp snooping unknown-multicast-fwd no ip igmp snooping mrouter learn pim-dvmrp autoinstall configuration autoinstall firmware --More-- cluster name cluster1 cluster member ip 1.2.3.4 level 2 cluster member ip 172.16.10.3 cluster member vlan 4094 cluster handle-stp cluster force-configured-state secure Optional. Ensures parts of a file that contain security information are not written during a reload
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 574 holdtime 1000 timer 900 configuration-persistence secure wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 575 controller Creating Profiles Sets the wireless controller as part of a pool and group Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax controller [group|vlan|host] controller [group <CONTROLLER-GROUP-NAME>|vlan <1-4094>] controller host [<IP>|<HOSTNAME>] [level [1|2]|pool <1-2> level [1|2]} Parameters controller [group <CONTROLLER-GROUP-NAME>|vlan <1-4094>] controller host [<IP>|<HOSTNAME>] {level [1|2]|pool <1-2> level [1|2]} controller Configures WLAN settings group <CONTROLLER-GROUP- NAME> Configures the wireless controller group <CONTROLLER-GROUP-NAME> Specify the wireless controller group name. vlan <1-4094> Configures the wireless controller VLAN <1-4094> Specify the VLAN ID from 1 - 4094. controller Configures WLAN settings host Configures wireless controllers host address [<IP>|<HOSTNAME> Provide the IP address or hostname <IP> Specify IP address of the wireless controller. <HOSTNAME> Specify the wireless controller name.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 576 Example wm3400-34710C8(config-profile-default-WM3700)#controller group test wm3400-34710C8(config-profile-default-WM3700)#controller host 1.2.3.4 pool 2 wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 no autoinstall configuration no autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp qos trust 802.1p interface ge4 ip dhcp trust qos trust dscp qos trust 802.1p use firewall-policy default controller host 1.2.3.4 pool 2 controller group test service pm sys-restart Related Commands level [1|2] The following are common to the IP and hostname parameters: Optional. After providing the wireless controller address, optionally select one of the following two routing levels: 1 Level 1, local routing 2 Level 2, inter-site routing pool <1-2> level [1|2] The following are common to the IP and hostname parameters: Optional. Sets the wireless controllers pool <1-2> Select either 1 or 2 as the pool. The default is 1. After selecting the pool, optionally select one of the following two routing levels: 1 Level 1, local routing 2 Level 2, inter-site routing no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 577 critical-resource Creating Profiles Monitors user configured IP addresses and logs their status Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax critical-resource monitor [direct|interval|via] critical-resource monitor direct [all|any] <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} critical-resource monitor interval <5-86400> critical-resource monitor via [<A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwan1] critical-resource monitor via [<A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwan1][all|any] <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}}] Parameters monitor direct [all|any] <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} monitor interval <5-86400> monitor Monitors configured critical resources direct Monitors the critical resources using the default routing engine all <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} Monitors all resources that are going down <A.B.C.D> {A.B.C.D> Specify the IP address to monitor arp-only vlan <1-4094> Use ARP to determine if the IP address is reachable. User needs to specify the VLAN ID for sending ARP request vlan <1-4094> Specify the VLAN ID on which the probing ARP requests should be sent. Specify a VLAN from 1-4094 any <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} Monitors any resource that is going down monitor interval <5-86400> Configures the frequency of critical resource monitoring <5-86400> Specifies the time in seconds. Specify the time from 5-86400 seconds. The default value is 30 seconds.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 578 monitor via [<A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwan1][all|any] <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} Example wm3400-34710C8(config-profile-default-wm3400)#critical-resource monitor interval 55 wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#critical-resource monitor direct all 172.16.10.2 arp-only vlan 1 wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#show critical-resources Critical Resource Monitor interval 30 ------------------------------------------------------------------------------- via wwan1 Status: DOWN (next-hop address is not known) monitor for all resources down RESOURCES: 172.16.10.10 down arp-and-ping ------------------------------------------------------------------------------- wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#critical-resource monitor via vlan 1 all 172.16.10.1 wm3400-34710C8(config-profile-default-wm3400)# via Specifies the interface or next-hop via which the ICMP pings should be sent. <A.B.C.D> Specify the IP address of the next-hop via which the critical resource(s) are to be monitored. NOTE Configures up to four IP addresses for monitoring. All the four IP addresses constitute on critical resource <WORD> Specify the layer 3 Interface name (router interface) pppoe1 Specifies PPoE interface vlan <1-4094> Specifies the controllers VLAN interface. Specify SVI VLAN ID from 1 - 4094. wwan1 Specifies Wireless WAN interface all <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} Monitors all the resources which are going down <A.B.C.D> {<A.B.C.D>} Specify the IP address to monitor arp-only vlan <1-4094> Uses ARP to determine if the IP address is reachable. Specify the VLAN ID for sending ARP request vlan <1-4094> Specify the VLAN ID on which the probing ARP requests should be sent. Specify a VLAN from 1- 4094 any <A.B.C.D> {<A.B.C.D>|arp-only vlan <1-4094> {<A.B.C.D>}} Monitors any resource that is going down
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 579 crypto Creating Profiles Use crypto to define system a level local ID for ISAKMP negotiation and to enter the ISAKMP Policy, ISAKMP Client, or ISAKMP Peer command set. A crypto map entry is a single policy that describes how certain traffic is secured. There are two types of crypto map entries: ipsec-manual and ipsec-ike entries. Each entry is given an index (used to sort the ordered list). When a non-secured packet arrives on an interface, the crypto map set associated with that interface is processed (in order). If a crypto map entry matches the non-secured traffic, the traffic is discarded. When a packet is transmitted on an interface, the crypto map set associated with that interface is processed. The first crypto map entry that matches the packet is used to secure the packet. If a suitable SA exists, it is used for transmission. Otherwise, IKE is used to establish an SA with the peer. If no SA exists (and the crypto map entry is respond only), the packet is discarded. When a secured packet arrives on an interface, its SPI is used to look up a SA. If a SA does not exist (or if the packet fails any of the security checks), it is discarded. If all checks pass, the packet is forwarded normally. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cr ypt o [ aut o- i psec- secur e| i kev1| i kev2| i psec| l oad- management | map| pki | pl ai n- t ext - deny- acl - scope] crypto ikev1 [dpd-keepalive <10-3600>|dpd-retries <1-100>|nat-keepalive <10-3600>| peer IKEV1-PEER|policy IKEV1-POLICY|remote-vpn] crypto ikev2 [cookie-challenge-threshold <1-100>|dpd-keepalive <10-3600>|dpd-retries <1-100>|nat-keepalive <10-3600>|peer IKEV2-PEER|policy IKEV2-POLICY|remote- vpn] crypto ipsec [df-bit [clear|copy|set]|include-alg-rules|security- association|transform-set] crypto ipsec security-association lifetime [kilobytes <500-2147483646>| seconds <90-2147483646>]
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 580 crypto transform-set <TRANSFORM-SET-TAG> [esp-3des|esp-aes|esp-aes-192| esp-aes-256|esp-des|esp-null] [esp-md5-hmac|esp-sha-hmac]] crypto map <CRYPTO-MAP-TAG> <1-1000> [ipsec-isakmp {dynamic}|ipsec-manual] crypto pki import crl <TRUSTPOINT> URL <1-168> crypto plain-text-deny-acl-scope [global|interface] Parameters auto-ipsec-secure crypto ikev1 [dpd-keepalive <10-3600>|dpd-retries <1-100>|nat-keepalive <10-3600>| peer IKEV1-PEER|policy IKEV1-POLICY|remote-vpn] crypto ikev2 [cookie-challenge-threshold <1-100>|dpd-keepalive <10-3600>| dpd-retries <1-100>|nat-keepalive <10-3600>|peer IKEV2-PEER|policy IKEV2-POLICY| remote-vpn] crypto ipsec [df-bit [clear|copy|set]|include-alg-rules|security-association lifetime [kilobytes <500-2147483646>|seconds <90-2147483646>]|transform-set] auto-ipsec-secure Configures Auto IPSec Secure parameter settings ikev1 Configures IKE version 1 parameters dpd-keepalive <10-3600> Sets the global Dead Peer Detection interval between 10 and 3600 seconds dpd-retries <1-1000> Sets the global Dead Peer Detection retries count between 1 and 1000 nat-keepalive <10-3600> Sets the global NAT keepalive interval between 10 and 3600 seconds peer IKEV1-PEER Specify the Name/Identifier for IKEv1 peer to be configured policy IKEV1-POLICY Configures an ISKAMP policy. Specify the name of the policy to be configured.The local IKE policy and the peer IKE policy must have matching group settings for negotiation to be successful. remote-vpn Specifies IKEV1 remote-VPN server configuration (responder only) cookie-challenge-threshold <1-100> Starts cookie challenge after half open IKE SAs crosses the specified limit. Sets the limit from 1 - 100 ikev2 Configures IKE version 2 parameters dpd-keepalive <10-3600> Sets the global Dead Peer Detection interval between 10 and 3600 seconds dpd-retries <1-1000> Sets the global Dead Peer Detection retries count between 1 and 1000 nat-keepalive <10-3600> Sets the global NAT keepalive interval between 10 and 3600 seconds peer IKEV2-PEER Specify the Name/Identifier for IKEv2 peer to be configured policy IKEV2-POLICY Configures an ISKAMP policy. Specify the name of the policy to be configured.The local IKE policy and the peer IKE policy must have matching group settings for negotiation to be successful. remote-vpn Specifies IKEV2 remote-VPN server configuration (responder only) ipsec Configures Internet Protocol Security (IPSec) policy parameters
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 581 crypto ipsec transform-set <TRANSFORM-SET-TAG> [esp-3des|esp-aes| esp-aes-192|esp-aes-256|esp-des|esp-null] {esp-md5-hmac|esp-sha-hmac} crypto load-management df-bit [clear|copy|set] Configures DF bit handling for encapsulating header. The configuration is of three types clear Clears DF bit in outer header and ignores in inner header copy Copies DF bit from inner header to outer header set Sets DF bit in outer header include-alg-rules Includes ALG rules in IPSEC ACLs security-association Configures IPSec SAs parameters lifetime [kilobyte |seconds] Defines IPSec SAs lifetime (in kilobytes and/or seconds). Values can be entered in both kilobytes and seconds, which ever limit is reached first, ends the SA. When the SA lifetime ends it is renegotiated as a security measure. kilobytes Specifies a volume-based key duration, the minimum is 500 KB and the maximum is 2147483646 KB. <500-2147483646> Specify a value from 500 - 2147483646 KB. seconds Specifies a time-based key duration, the minimum is 90 seconds and the maximum is 2147483646 seconds <90-2147483646> Specify a value from 90 - 2147483646 seconds ipsec Configures IPSec policy parameters transform-set <TRANSFORM-SET-TAG> Defines transform configuration (authentication and encryption) for securing data <TRANSFORM-SET-TAG> Specify the transform set name. Specify the transform set used by the IPSec transport connection to negotiate the transform algorithm. esp-3des Configures the ESP transform using 3DES cipher (168 bits). The transform set is assigned to a crypto map using the maps set transform-set command. esp-aes Configures the ESP transform using Advanced Encryption Standard (AES) cipher. The transform set is assigned to a crypto map using the maps set transform-set command. esp-aes-192 Configures the ESP transform using AES cipher (192 bits). The transform set is assigned to a crypto map using the maps set transform-set command. esp-aes-256 Configures the ESP transform using AES cipher (256 bits). The transform set is assigned to a crypto map using the maps set transform-set command. esp-des Configures the ESP transform using Data Encryption Standard (DES) cipher (56 bits). The transform set is assigned to a crypto map using the maps set transform-set command. esp-null Configures the ESP transform with no encryption {esp-md5-hmac|esp-sha- hmac} The following are common to all of the above transform sets: esp-md5-hmac Optional. Configures ESP transform using HMAC-MD5 authorization esp-sha-hmac Optional. Configures ESP transform using HMAC-SHA authorization load-management Configures load management for platforms using software cryptography
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 582 crypto map <CRYPTO-MAP-TAG> <1-1000> [ipsec-isakmp {dynamic}|ipsec-manual] crypto pki import crl <TRUSTPOINT> <URL> <1-168> crypto plain-text-deny-acl-scope [global|interface] map <CRYPTO-MAP-TAG> Configures the crypto map, a software configuration entity that selects data flows that require security processing. The crypto map also defines the policy for these data flows. <CRYPTO-MAP-TAG> Specify a name for the crypto map. The name should not exceed 32 characters. <1-1000> Defines the crypto map entry sequence. Specify a value from 1 - 1000. ipsec-isakmp {dynamic} Configures IPSEC w/ISAKMP. dynamic Optional. Configures dynamic map entry (remote VPN configuration) for XAUTH with mode-config or ipsec-l2tp configuration ipsec-manual Configures IPSEC w/manual keying. Remote configuration is not allowed for manual crypto map pki Configures certificate parameters. The Public Key Infrastructure (PKI) protocol creates encrypted public keys using digital certificates from certificate authorities. import Imports a trustpoint related configuration crl <TRUSTPOINT> Imports a Certificate Revocation List (CRL). Imports a trustpoint including either a private key and server certificate or a CA certificate or both <TRUSTPOINT> Specify the trustpoint name. <URL> Specify the CRL source address in the following format: tftp://<hostname|IP>[:port]/path/file ftp://<user>:<passwd>@<hostname|IP>[:port]/path/file sftp://<user>:<passwd>@<hostname|IP>[:port]>/path/file http://<hostname|IP>[:port]/path/file cf:/path/file usb1:/path/file usb2:/path/file <1-168> Sets command replay duration from 1 - 168 hours plain-text-deny-acl-scope Configures plain-text-deny-acl-scope parameters global Specifies plain-text-deny-acl as global interface Specifies plain-text-deny-acl per interface
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 583 Usage Guidelines If no peer IP address is configured, the manual crypto map is not valid and not complete. A peer IP address is required for manual crypto maps. To change the peer IP address, the no set peer command must be issued first, then the new peer IP address can be configured. A peer address can be deleted with a wrong ISAKMP value. Crypto currently matches only the IP address when a no command is issued. wm3400-34710C8( conf i g- pr of i l e- def aul t - wm3400) #cr ypt o i sakmp key 12345678 addr ess 4. 4. 4. 4 Example wm3400-34710C8(config-profile-default-WM3400)#crypto ipsec transform-set tpsec-tag1 ah-md5-hmac wm3400-34710C8(config-profile-default-WM3400-transform-set-tpsec-tag1)# wm3400-34710C8(config-profile-default-WM3400)#crypto map map1 10 ipsec-isakmp d ynamic wm3400-34710C8(config-profile-default-WM3400-cryptomap-map1 10)# wm3400-34710C8(config-profile-default-wm3400)#crypto plain-text-deny-acl-scope interface wm3400-34710C8(config-profile-default-wm3400)#show context profile wm3400 default-wm3400 bridge vlan 1 bridging-mode isolated-tunnel ip igmp snooping ip igmp snooping querier autoinstall configuration autoinstall firmware crypto ikev1 policy ikev1-default isakmp-proposal default encryption aes-256 group 2 hash sha crypto ikev2 cookie-challenge-threshold 1 crypto ikev2 policy ikev2-default isakmp-proposal default encryption aes-256 group 2 hash sha crypto ipsec transform-set default esp-aes-256 esp-sha-hmac crypto ikev1 remote-vpn crypto ikev2 remote-vpn crypto auto-ipsec-secure crypto plain-text-deny-acl-scope interface interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 584 qos trust 802.1p interface ge4 ip dhcp trust qos trust dscp qos trust 802.1p interface pppoe1 use firewall-policy default service pm sys-restart router ospf wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#crypto ipsec transform-set tag1 esp- null esp-md5-hmac wm3400-34710C8(config-profile-default-wm3400-transform-set-tag1)# wm3400-34710C8(config-profile-default-wm3400)#crypto ikev2 remote-vpn wm3400-34710C8(config-profile-default-wm3400-ikev2-remote-config)# wm3400-34710C8(config-profile-default-wm3400-transform-set-tag1)#? Crypto Ipsec Configuration commands: mode Encapsulation mode (transport/tunnel) no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-wm3400-transform-set-tag1)# wm3400-34710C8(config-profile-default-wm3400)#crypto map map1 12 ipsec-isakmp dynamic wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#12)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 585 Crypto-auto-ipsec-secure Commands Creating Profiles Creates an auto IPSec VPN tunnel and changes the mode to auto-ipsec-secure mode for further configuration. wm3400-34710C8(config-profile-default-wm3400)#crypto auto-ipsec-secure wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)#? Crypto Auto IPSEC Tunnel commands: groupid Local/Remote identity and Authentication credentials for Auto IPSec Secure IKE negotiation no Negate a command or set its defaults remotegw-ike-version IKE version used for auto ipsec secure tunnel with secure gateways clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)# Command Description Reference groupid Specifies the identity string used for IKE authentication page 8-586 remotegw-ike- version Defines the IKE version used for an auto IPSec secure tunnel using secure gateways page 8-587 no Negates a command or sets its default values page 8-588
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 586 groupid Crypto-auto-ipsec-secure Commands Specifies the identity string used for IKE authentication Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax groupid <WORD> [psk [0|2|<WORD>]|rsa] Parameters groupid <WORD> [psk [0|2|<WORD>]|rsa] NOTE Only one group ID is supported on the controller. All APs and controllers must use the same group ID. Example wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)#show context crypto auto-ipsec-secure groupid autotunnel psk 0 symbol123 wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)# <WORD> Specify a string up to 64 characters psk [0|2|<WORD>] Configures pre-shared key 0 Enter a clear text key 2 Enter an encrypted key <WORD> Specify a string value from 8 - 21 characters. rsa Configures Rivest-Shamir-Adleman (RSA) key
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 587 remotegw-ike-version Crypto-auto-ipsec-secure Commands Defines the IKE version used for auto IPSEC secure tunnel negotiation using a secure gateway Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax remotegw-ike-version [ikev1-aggr|ikev1-main|ikev2] Parameters remotegw-ike-version [ikev1-aggr|ikev1-main|ikev2] Example wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)#remotegw-ike- version ikev2 wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)# ikev1-aggr Aggregation mode is used by auto IPSec secure tunnel initiator to set up the connection ikev1-main Main mode is used by auto IPSec secure tunnel initiator to establish the connection ikev2 IKEv2 is preferred method when controller/AP only is used
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 588 no Crypto-auto-ipsec-secure Commands Negates a command or set its defaults Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no groupid Parameters no groupid Example wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)#no groupid wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)#show context crypto auto-ipsec-secure no groupid wm3400-34710C8(config-profile-default-wm3400-crypto-auto-ipsec-secure)# groupid Removes local/remote identity for auto IPSec secure IKE
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 589 crypto-ikev1 policy commands Defines crypto-IKEv1/IKEv2 commands in detail. Use the (config) instance to configure IKEv1 policy configuration commands. To navigate to the IKEv1 policy instance, use the following commands: wm3400-34710C8(config-profile-default-wm3400)#crypto ikev1 policy ikev1-testpolicy wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)#? Crypto IKEv1 Policy Configuration commands: dpd-keepalive Set Dead Peer Detection interval in seconds dpd-retries Set Dead Peer Detection retries count isakmp-proposal Configure ISAKMP Proposals lifetime Set lifetime for ISAKMP security association mode IKEv1 mode (main/aggressive) no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)# Command Description Reference dpd-keepalive Sets Dead Peer Detection interval in seconds page 8-590 dpd-retries Sets Dead Peer Detection retries count value page 8-591 isakmp-proposal Configures ISAKMP proposals page 8-592 lifetime Specifies how long an IKE SA is valid before it expires page 8-594 mode Sets the mode of the tunnels page 8-595 no Negates a command or sets its default values page 8-596
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 590 dpd-keepalive crypto-ikev1 policy commands Sets Dead Peer Detection (DPD) interval in seconds Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dpd-keepalive <10-3600> Parameters dpd-keepalive <10-3600> Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)#dpd- keepalive 11 wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)# <10-3600> Specifies the interval between successive DPD keepalives. Specify the time from 10 - 3600 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 591 dpd-retries crypto-ikev1 policy commands Sets the DPD retry interval Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dpd-retries <1-100> Parameters dpd-retries <1-100> Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)#dpd- retries 10 wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)# <1-100> Declares a peer dead after the specified number of retries. Specify a value from 1-100.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 592 isakmp-proposal crypto-ikev1 policy commands Configures ISAKMP proposals Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax isakmp-proposal <WORD> encryption [3des|aes|aes-192|aes-256] group [14|2|5] hash [md5|sha] Parameters isakmp-proposal <WORD> encryption [3des|aes|aes-192|aes-256] group [14|2|5] hash [md5|sha] <WORD> Specify the name of the ISAKMP proposal to configure encryption [3des|aes| aes-192|aes-256] Configures the encryption level transmitted using the crypto isakmp command 3des Configures triple data encryption standard aes Configures Advanced Encryption Standard (AES) (128 bit keys) aes-192 Configures Advanced Encryption Standard (AES) (192 bit keys) aes-256 Configures AES (256 bit keys) group [14|2|5] Specifies the Diffie-Hellman (DH) group (1 or 2) used by the IKE policy to generate keys (used to create IPSec SA). Specifying the group enables you to declare the size of the modulus used in DH calculation. 14 Configures DH group 14 2 Configures DH group 2 5 Configures DH group 5 hash [md5|sha] Specifies the hash algorithm used to authenticate data transmitted over the IKE SA md5 Uses Message Digest 5 (MD5) hash algorithm sha Uses Secure Hash Authentication (SHA) hash algorithm
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 593 Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)#isakmp- proposal testproposal encryption aes group 2 hash sha wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-ikev1-testpolicy)#
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 594 lifetime crypto-ikev1 policy commands Specifies how long an IKE SA is valid before it expires Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax lifetime <600-86400> Parameters lifetime <600-86400> Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)#lifetime 655 wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)# <lifetime 600-86400> Specifies how many seconds an IKE SA lasts before it expires. Set a time stamp from 60 - 86400 seconds. <60-86400> Specify a value from 60 -86400 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 595 mode crypto-ikev1 policy commands Configures the IPSec mode of operation Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mode [aggresive|main] Parameters mode [aggresive|main] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)#mode main wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)# mode [aggresive|main] Sets the mode of the tunnels aggressive Initiates aggressive mode main Initiates main mode
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 596 no crypto-ikev1 policy commands Negates a command or set its defaults Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [dpd-keepalive|dpd-retries|isakmp-proposal|lifetime|mode] Parameters no [dpd-keepalive|dpd-retries|isakmp-proposal|lifetime|mode] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)#no mode wm3400-34710C8(config-profile-default-wm3400-ikev1-policy-test-ikev1policy)# dpd-keepalive Resets the DPD keepalive interval to default value dpd-retries Resets the DPD retries count to default isakmp-proposal Removes the configured ISAKMP Proposal lifetime Resets the lifetime for ISAKMP security association mode The default mode is set to IKEv1 main mode
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 597 crypto-ikev1-peer commands Use the (config) instance to configure IKEv1 peer configuration commands. To navigate to the IKEv1 peer instance, use the following commands: wm3400-34710C8(config-profile-default-wm3400)#crypto ikev1 peer peer1 wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-peer1)#? Crypto IKEV1 Peer Configuration commands: authentication Configure Authentication credentails ip Configure peer address/fqdn localid Set local identity no Negate a command or set its defaults remoteid Configure remote peer identity use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-peer1)#
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 598 authentication crypto-ikev1-peer commands Sets the peer authentication Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication [psk|rsa] authentication psa [0 <WORD>|2 <WORD>|<WORD>] Parameters authentication [psk [0 <WORD>|2 <WORD>|<WORD>]|rsa] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-peer1)#authentication rsa wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-peer1)# psk [0 <WORD>|2 <WORD>|<WORD> Configures an authentication method which uses pre-shared key 0 <WORD> Specifies a clear text key. The key must be from 8-21 characters in length 2 <WORD> Specifies an encrypted key. The key must be from 8-21 characters in length <WORD> Pre-shared key. The key must be from 8-21 characters in length rsa Configures a authentication method which uses Rivest-Shamir-Adleman (RSA) key
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 599 ip crypto-ikev1-peer commands Sets the IP address of the peer device. This can be set for multiple remote peers. The remote peer can be either an IP address or hostname. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [address <A.B.C.D>|fqdn <WORD>] Parameters ip [address <A.B.C.D>|fqdn <WORD>] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)#ip address 172.16.10.12 wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)# address <A.B.C.D> Specify the IP address of the peer to configure fqdn <WORD> Specify the Fully Qualified Domain Name (FQDN) host name of the peer to configure
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 600 localid crypto-ikev1-peer commands Sets local identity details Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax localid [address <A.B.C.D>|dn <WORD>|email <WORD>|fqdn <WORD>|string <WORD>] Parameters localid [address <A.B.C.D>|dn <WORD>|email <WORD>|fqdn <WORD>|string <WORD>] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)#localid email [email protected] wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)# address <A.B.C.D> Configures IP address of the peer. The IP address is used as local identity. dn <WORD> Configures distinguished name of the peer. E.g. "C=us ST=<state> L=<location> O=<organization> OU=<org unit>". The maximum length is 128 characters. email <WORD> Configures the e-mail address of the peer. The maximum length is 128 characters. fqdn <WORD> Configures Fully Qualified Domain Name(FQDN) of the peer. The maximum length is 128 characters. string <WORD> Configures identity string of the peer. The maximum length is 128 characters
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 601 remoteid crypto-ikev1-peer commands Sets remote identity details Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax remoteid [address <A.B.C.D>|dn <WORD>|email <WORD>|fqdn <WORD>|string <WORD>] Parameters remoteid [address <A.B.C.D>|dn <WORD>|email <WORD>|fqdn <WORD>|string<WORD>] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)#remoteid dn India wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)# address <A.B.C.D> Configures IP address of the peer. The IP address is used as the peers remote identity. dn <WORD> Configures distinguished name of the peer. E.g. "C=us ST=<state> L=<location> O=<organization> OU=<org unit>". The maximum length is 128 characters. email <WORD> Configures the e-mail address of the peer. The maximum length is 128 characters. fqdn <WORD> Configures Fully Qualified Domain Name (FQDN) of the peer. The maximum length is 128 characters. string <WORD> Configures identity string of the peer. The maximum length is 128 characters
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 602 use crypto-ikev1-peer commands Uses IKEv1 ISAKMP policy configuration settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use ikev1-policy <IKEV1-POLICY> Parameters use ikev1-policy <IKEV1-POLICY> Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)#use ikev1-policy test-ikev1policy wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)# use ikev1-policy <IKEV1- POLICY> Specify the name of the IKEv1 ISAKMP policy. The local IKE policy and the peer IKE policy must have matching group settings for negotiation to be successful.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 603 no crypto-ikev1-peer commands Negates a command or reverts settings to their default. The no command, when used in the ISAKMP policy mode, defaults the ISAKMP protection suite settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [authentication|ip|localid|remoteid|use] Parameters no [authentication|ip|localid|remoteid|use] Example wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)#no localid wm3400-34710C8(config-profile-default-wm3400-ikev1-peer-tespeer)# authentication Unconfigures the authentication credentials of the peer ip Removes IP address /FQDN localid Removes local identity details of the peer remoteid Removes remote identity details of the peer use Resets the IKEv1 ISAKMP policy settings
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 604 crypto map commands This section explains crypto map commands in detail. A crypto map entry is a single policy that describes how certain traffic is secured. There are two types of crypto map entries: ipsec-manual and ipsec-ike entries. Each entry is given an index (used to sort the ordered list) Use the (config) instance to configure crypto map configuration commands. To navigate to the config- map instance, use the following commands: wm3400-34710C8(config-profile-default-wm3400)#crypto map map1 1 ipsec-manual wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#? Manual Crypto Map Configuration commands: local-endpoint-ip Use this IP as local tunnel endpoint address, instead of the interface IP (Advanced Configuration) mode Set the tunnel mode no Negate a command or set its defaults peer Set peer security-association Set security association parameters session-key Set security session key parameters use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# Command Description Reference local-endpoint-ip Uses the configured IP as local tunnel endpoint address, instead of the interface IP (Advanced Configuration) page 8-605 mode Sets the mode of the tunnels for this crypto map mode peer Sets the IP address of the peer device page 8-607 security- association Defines the lifetime (in kilobytes and/or seconds) of the IPSec SAs created by the crypto map page 8-608 session-key Use the session-key command to define the encryption and authentication keys for this crypto map page 8-609 use Uses the configured IP access list page 8-611 no Negates a command or sets its default value page 8-612
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 605 local-endpoint-ip crypto map commands Uses the configured IP as local tunnel endpoint address, instead of the interface IP (Advanced Configuration) Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax local-endpoint-ip <A.B.C.D> Parameters local-endpoint-ip <A.B.C.D> Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#local-endpoint-ip 172.16.10.3 wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# local-endpoint-ip <A.B.C.D> Uses the configured IP as local tunnel endpoint address, instead of the interface IP <A.B.C.D> Specify the IP address. The specified IP address must be available on the interface.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 606 mode crypto map commands Sets the crypto map tunnel mode Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mode [transport|tunnel] Parameters mode [transport|tunnel] Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#mode tunnel wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# mode [transport|tunnel] Sets the mode of the tunnels for this crypto map transport Initiates transport mode tunnel Initiates tunnel mode
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 607 peer crypto map commands Sets the IP address of the peer device. This can be set for multiple remote peers. The remote peer can be either an IP address. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax peer <A.B.C.D> Parameters peer <A.B.C.D> Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#peer 172.16.10.8 wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# peer <A.B.C.D>] Enter the IP address of the peer device. If not configured, it implies responder only to any peer
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 608 security-association crypto map commands Defines the lifetime (in kilobytes and/or seconds) of the IPSec SAs created by this crypto map Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax security-association lifetime [kilobytes <500-2147483646>|seconds <120-86400>] Parameters security-association lifetime [kilobytes <500-2147483646>|seconds <120-86400>] Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#security-association lifetime seconds 123 wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# lifetime [kilobytes <500- 2147483646>|seconds <120-86400>] Values can be entered in both kilobytes and seconds. Which ever limit is reached first, ends the security association. kilobytes <500-2147483646> Defines the volume based key duration in kilobytes. Specify a value from 500 - 2147483646 bytes. seconds <120-86400> Defines time based key duration in seconds. Specify the time frame from 120 - 86400 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 609 session-key crypto map commands Use the session-key command to define the encryption and authentication keys for this crypto map Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax session-key [inbound|outbound] [ah|esp] <256-4294967295> session-key [inbound|outbound] ah <256-4294967295> [0|2|authenticator [md5|sha]] <WORD> session-key [inbound|outbound] esp <256-4294967295> [0|2|cipher [3des|aes|aes-192| aes-256|des|esp-null]] <WORD> authenticator [md5|sha] <WORD> Parameters [inbound|outbound] [ah|esp] <256-4294967295> ah <256-4294967295> [0|2|authenticator [md5|sha] <WORD>] inbound [ah|esp] Define encryption keys for inbound traffic outbound [ah|esp] Defines encryption keys for outbound traffic <256-4294967295> Sets Security Parameter Index (SPI) for the security association from 256- 4294967295 ah <256-4294967295 Authentication header protocol Sets Security Parameter Index (SPI) for the security association from 256- 4294967295 [0|2|authenticator [md5|sha] <WORD>] 0 Enter a clear text key 2 Enter an encrypted key authenticator Specify AH authenticator details md5 <WORD> AH with MD5 authentication sha <WORD> AH with SHA authentication <WORD> Sets security association key value. The following key lengths (in hex characters) are required (w/o leading 0x).AH-MD5: 32, AH-SHA: 40
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 610 esp <256-4294967295> [0|2|cipher [3des|aes|aes-192|aes-256|des|esp-null]] <WORD> authenticator [md5|sha] <WORD>] Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#session-key inbound esp 273 cipher esp-null authenticator sha 32 % Error: Parsing "session-key inbound esp 273 cipher esp-null authenticator sha 32 " in mode 155: 1 wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# esp <256-4294967295> Encapsulating security payload protocol <256-4294967295> Defines the security association parameter index [0|2|cipher [3des|aes|aes- 192|aes-256|des|esp-null]] 0 Enter a clear text key 2 Enter an encrypted key cipher Specifies encryption/decryption key details 3des ESP with 3DES encryption aes ESP with AES encryption aes-192 ESP with AES-192 encryption aes-256 ESP with AES-256 encryption des ESP with DES encryption esp-null ESP with no encryption authenticator Specify ESP authenticator details md5 <WORD> ESP with MD5 authentication sha <WORD> ESP with SHA authentication <WORD> Sets security association key value. The following key lengths (in hex characters) are required (w/o leading 0x).AH-MD5: 32, AH-SHA: 40
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 611 use crypto map commands Uses the configured IP access list Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use ip-access-list <IP-ACCESS-LIST> Parameters use ip-access-list <IP-ACCESS-LIST> Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#use ip-access-list test-acl wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# ip-access-list <IP-ACCESS-LIST> Specify the IP access list name
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 612 no crypto map commands Negates a command or sets its default value Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [local-endpoint-ip|mode|peer|security-association|session-key|use] Parameters no [local-endpoint-ip|mode|peer|security-association|session-key|use] Example wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)#no local-endpoint-ip wm3400-34710C8(config-profile-default-wm3400-cryptomap-map1#1)# no local-endpoint-ip Deletes local IP address no mode Resets tunnel mode to default (TUNNEL) no peer Deletes the remote peer settings no security-association Deletes security association parameters no session-key Deletes session key parameters no use Resets the IP access list parameters values
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 613 dscp-mapping Creating Profiles Configures IP Differentiated Services Code Point (DSCP) to 802.1p priority mapping for untagged frames Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dscp-mapping <WORD> priority <0-7> Parameters dscp-mapping <word> priority <0-7> Example wm3400-34710C8(config-profile-default-WM3700)#dscp-mapping 20 priority 7 wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 dscp-mapping 20 priority 7 no autoinstall configuration no autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp Related Commands <WORD> Specify a DSCP value of a received IP packet. This could be a single value or a list. For example, 10-20,25,30-35 priority <0-7> Specifies the 802.1p priority to use for a packet if untagged. The priority is set on a scale of 0 - 7. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 614 email-notification Creating Profiles Configures e-mail notification settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax email-notification [host <IP>|recipient <EMAIL>] email-notification host <SMTP-SERVER-IP> sender <EMAIL> {port|username} email-notification host <SMTP-SERVER-IP> sender <EMAIL> {port <1-65535>} {username <SMTP-USERNAME>} [password [2 <WORD>|<WORD>]] email-notification host <SMTP-SERVER-IP> sender <EMAIL> {username <SMTP-USERNAME>} [password [2 <WORD>|<WORD>]] {port <1-65535>} Parameters email-notification recipient <EMAIL> email-notification host <SMTP-SERVER-IP> sender <EMAIL> {port <1-65535>}{username <SMTP-USERNAME>} [password [2 <WORD>|<WORD>]] recipient Defines the e-mail address of the recipient <EMAIL> Specify the e-mail address of the recipient. host <SMTP-SERVER-IP> Configures the host SMTP server <SMTP-SERVER-IP> Specify the IP address of the SMTP server. sender <EMAIL> Defines the e-mail address of the sender <EMAIL> Specify the e-mail address of the sender. port <1-65535> Optional. Configures the SMTP server port <1-65535> Specify the port from 1 - 65535. username <SMTP-USERNAME> Optional. Configures the SMTP server username <SMTP-USERNAME> Specify the SMTP username.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 615 email-notification host <SMTP-SERVER-IP> sender <EMAIL> {username <SMTP-USERNAME>} [password [2 <WORD>|<WORD>] {port <1-65535] Example wm3400-34710C8config-profile-default-WM3700)#email-notification recipient [email protected] wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 dscp-mapping 20 priority 7 no autoinstall configuration no autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac ip dhcp trust interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp qos trust 802.1p interface ge4 ip dhcp trust qos trust dscp qos trust 802.1p use firewall-policy default email-notification recipient [email protected] service pm sys-restart password [2 <WORD>|<WORD>] Configures the SMTP server password 2 <WORD> Configures an encrypted password <WORD> Specify the password. recipient Defines the e-mail address of the recipient <EMAIL> Specify the e-mail address of the recipient. host <SMTP-SERVER-IP> Configures the host SMTP server <SMTP-SERVER-IP> Specify the IP address of the SMTP server. sender <EMAIL> Defines the e-mail address of the sender <EMAIL> Specify the e-mail address of the sender. username <SMTP-USERNAME> Optional. Configures the SMTP username <SMTP_USERNAME> Specify the SMTP username. password [2 <WORD>|<WORD>] Configures the SMTP server password 2 <WORD> Configures an encrypted password <WORD> Specify the password. port <1-65535> Optional. Configures the SMTP server port <1-65535> Specify the port from 1 - 65535.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 616 Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 617 enforce-version Creating Profiles Checks device firmware versions before attempting connection Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax enforce-version [adoption|cluster] [full|major|none|strict] Parameters enforce-version [adoption|cluster] [full|major|none|strict] adoption Checks firmware versions before adopting cluster Checks firmware versions before clustering full Allows adoption or clustering when firmware versions match exactly major Allows adoption or clustering when major and minor versions match exactly none Allows adoption or clustering between any firmware versions strict Allows adoption or clustering when firmware versions match exactly
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 618 Example wm3400-34710C8(config-profile-default)#enforce-version cluster full wm3400-34710C8(config-profile-default)#enforce-version adoption major wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 dscp-mapping 20 priority 7 no autoinstall configuration no autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp qos trust 802.1p interface ge4 ip dhcp trust qos trust dscp qos trust 802.1p use firewall-policy default email-notification recipient [email protected] enforce-version adoption major enforce-version cluster full service pm sys-restart Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 619 events Creating Profiles Displays system event messages Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax events [forward on|on] Parameters event [forward on|on] Example wm3400-34710C8(config-profile-default-WM3700)#events forward on wm3400-34710C8(config-profile-default-WM3700)# Related Commands forward on Forwards system event messages to the wireless controller or cluster members on Enables forwarding of system events on Generates system events on this wireless controller no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 620 ip Creating Profiles Configures IP components, such as default gateway, DHCP, Domain Name Service (DNS) server forwarding, name server, domain name, routing standards etc. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [default-gateway|dhcp|dns-server-forward|domain-lookup|domain-name|igmp| name-server|nat|route|routing] ip [default-gateway <IP>|dns-server-forward|domain-lookup|domain-name <DOMAIN-NAME>| name-server <IP>|routing] ip dhcp client [hostname|persistent-lease] ip igmp snooping [forward-unknown-multicast|querier] ip igmp snooping forward-unknown-multicast ip igmp snooping querier {max-response-time <1-25>|query-interval <1-18000>| robustness-variable <1-7>|timer expiry <60-300>|version <1-3>} NOTE The command ip igmp snooping can be configured under bridge VLAN context also. For example: wm3400-34710C8(config-device 00-15-70-37-FA-BE-bridge-vlan-1)#ip igmp snooping forward-unknown-multicast ip nat [inside|outside|pool] ip nat pool <NAT-POOL-NAME>] ip nat [inside|outside] [destination|source] ip nat [inside|outside] destination static <ACTUAL-IP> [<1-65535> [tcp|udp]] [(<NATTED-IP> {<1-65535>})]
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 621 ip nat [inside|outside] source [list|static] ip nat [inside|outside] source static <ACTUAL-IP> <NATTED-IP> ip nat [insdie|outside] source list <IP-ACCESS-LIST> interface [<INTERFACE>| vlan <1-4094>] [(address <IP>|interface <L3IFNAME>|overload| pool <NAT-POOL-NAME>)] ip route <IP/M> <IP> Parameters ip [default-gateway <IP>|dns-server-forward|domain-lookup| domain-name <DOMAIN-NAME>|name-server <IP>|routing] ip dhcp client [hostname|persistent-lease] ip igmp snooping forward-unknown-multicast ip igmp snooping querier {max-response-time <1-25>|query-interval <1-18000>| robustness-variable <1-7>|timer expiry <60-300>|version <1-3>} default-gateway <IP> Configures the IP address of the default gateway (next-hop router) <IP> Specify the default gateways IP address. dns-server-forward Enables DNS forwarding. This command enables the forwarding of DNS queries to DNS servers outside of the network. domain-lookup Enables domain lookup domain-name <DOMAIN-NAME> Configures a default domain name <DOMAIN-NAME> Specify a name for the DNS. name-server <IP> Configures IP address of the name server <IP> Specify the IP address of the name server. routing Enables IP routing of logically addressed packets from their source to their destination dhcp Configures Dynamic Host Control Protocol (DHCP) client and host client [hostname|persistent-lease] Sets the DHCP client hostname Includes the hostname in the DHCP request persistent-lease Retains the last lease across reboot if the DHCP server is unreachable igmp snooping forward-unknown-multicast Enables/disables unknown multicast data packets to be flooded in the specified VLAN. By default the unknown-multicast-fwd is disabled igmp snooping querier Enables/disables IGMP querier functionality for the specified VALN. By default IGMP snooping querier is disabled. max-response-time <1-25> Configures the IGMP maximum query response interval used in IGMP V2/V3 queries for the given VLAN. The default value is 10 seconds. query-interval <1-18000> Configures IGMP querier query interval in seconds. Specify time frame from 1 - 18000 seconds.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 622 ip nat pool <NAT-POOL-NAME> ip nat [inside|outside] destination static <ACTUAL-IP> [<1-65535> [tcp|udp]] [(<NATTED-IP> {<1-65535>})]] ip nat [inside|outside] source static <ACTUAL-IP> <NATTED-IP> ip nat [inside|outside] source list <IP-ACCESS-LIST> interface [<INTERFACE>| vlan <1-4094>] [(address <IP>|interface <L3IFNAME>|overload|pool <NAT-POOL-NAME>)] robustness-variable <1-7> Configures IGMP robustness variable from 1 - 7 timer expiry <60-300> Configures the other querier time out value for the given VLAN. The default value is 60 seconds. version <1-3> Configures the IGMP query version for the given VLAN. The default value is 3. nat Configures Network Address Translation (NAT) parameters pool <NAT-POOL-NAME> Configures a pool of IP addresses for NAT <NAT-POOL-NAME> Specify a name for the NAT pool. nat Configures NAT parameters [inside|outside] Configures inside and outside address translation for the destination inside Configures inside address translation outside Configures outside address translation destination static <ACTUAL- IP> The following are common to the inside and outside parameters: destination Specifies destination address translation parameters static Specifies static NAT local to global mapping <ACTUAL-IP> Specify the actual outside IP address to map. <1-65535> [tcp|udp] <1-65535> Configures the actual outside port. Specify a value from 1 - 65535. tcp Configures Transmission Control Protocol (TCP) port udp Configures User Datagram Protocol (UDP) port <NATTED-IP> <1-65535> Enables configuration of the outside natted IP address <NATTED-IP> Specify the outside natted IP address. <1-65535> Optional. Configures the outside natted port. Specify a value from 1 - 65535. nat Configures NAT parameters [inside|outside] Configures inside and outside address translation for the source inside Configures inside address translation outside Configures outside address translation source static <ACTUAL-IP> <NATTED-IP> The following are common to the inside and outside parameters: source Specifies source address translation parameters static Specifies static NAT local to global mapping <ACTUAL-IP> Specify the actual inside IP address to map. <NATTED-IP> Specify the natted IP address to map. nat Configures NAT parameters
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 623 ip route <IP/M> <IP>] Example wm3400-34710C8(config-profile-default-WM3700)#ip default-gateway 172.16.10.9 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#ip dns-server-forward wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#ip route 172.16.10.10/24 172.16.10.2 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3400)#ip local pool default low-ip-address 1.2.3.4 high-ip-address 6.7.8.9 wm3400-34710C8(config-profile-default-WM3400)# wm3400-34710C8(config-profile-default-WM3400)#ip nat inside source list test interface vlan 1 pool pool1 overload wm3400-34710C8(config-profile-default-WM3400)# wm3400-34710C8(config-profile-default-wm3400)#ip igmp snooping querier version 1 wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8config-profile-default-WM3400)#ip nat pool pool1 prefix-length 9 [inside|outside] Configures inside and outside IP access list source list <IP-ACCESS-LIST> Configures an access list describing local addresses <IP-ACCESS-LIST> Specify a name for the IP access list. interface [<INTERFACE>|vlan <1- 4094> interface Selects an interface to configure. Select a layer 3 router interface or a VLAN interface. <INTERFACE> Selects a layer 3 interface. Specify the layer 3 router interface name. vlan Selects a VLAN interface <1-4094> Set the SVI VLAN ID of the interface. address <IP> The following is a recursive parameter and common to both the layer 3 and VLAN interfaces: Configures the interface IP address used with NAT interface <L3IFNAME> The following is a recursive parameter and common to both the layer 3 and VLAN interfaces: Configures a wireless controller VLAN interface <L3IFNAME> Specify the SVI VLAN ID of the interface. overload Enables use of global address for many local addresses pool <NAT-POOL-NAME> Specifies the NAT pool <NAT-POOL-NAME> Specify the NAT pool name. route Configures static routes <IP/M> Specify the IP destination prefix in the A.B.C.D/M format. <IP> Specify the IP address of the gateway.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 624 wm3400-34710C8(config-profile-default-WM3400-nat-pool-pool1)# wm3400-34710C8(config-profile-default-WM3400-nat-pool-pool1)#? Nat Policy Mode commands: address Specify addresses for the nat pool no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1) Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 625 l2tpv3 Creating Profiles Defines the Layer 2 Tunnel Protocol (L2TP) protocol for tunneling Layer 2 payloads using Virtual Private Networks (VPNs) Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax l2tpv3 [hostname <HOSTNAME>|inter-tunnel-bridging|manual-session| router-id [<1-4294967295>|<IP-ADDRESS>]|tunnel|udp-listen-port <1024-65535>] Parameters l2tpv3 [hostname <HOSTNAME>|inter-tunnel-bridging|manual-session| router-id [<1-4294967295>|<IP-ADDRESS>]|tunnel|udp-listen-port <1024-65535>] l2tpv3 Configures the L2TPV3 protocol settings for a profile hostname <HOSTNAME> Configures the host name that will be sent in the L2TPV3 signalling messages <HOSTNAME> Specify the L2TPV3 specific host name. inter-tunnel-bridging Enables inter tunnel bridging of packets manual-session Creates/modifies L2TPV3 manual sessions For more information, see l2tpv3-manual-session-commands on page 26-1145 router-id [<1-4294967295>| <IP-ADDRESS>] Configures the router ID that will be sent un L2TPV3 signalling messages <1-4294967295> Configures the router ID in decimal format from 1 - 4294967295 <IP-ADDRESS> Configures the router ID in the IP address (A.B.C.D) format tunnel Creates/modifies L2TPV3 tunnel For more information, see l2tpv3-tunnel-commands. udp-listen-port <1024-65535> Configures the UDP port, on this device, running the L2TPV3 service <1024-65535> Specify the UDP port from 1024 - 65535 (default is 1701)
TM 4000 Series Access Point CLI Reference Guide 627 Related Commands no Negates L2TPV3 tunnels settings on this profile
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 628 nat-pool Creating Profiles Use the (config-profile-default-WM3700) instance to configure Network Address Translation (NAT) pool commands. wm3400-34710C8config-profile-default-WM3700)#ip nat pool pool1 prefix-length wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)#ip nat pool pool1 prefix-length 1 wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)#? Nat Policy Mode commands: address Specify addresses for the nat pool no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8( conf i g- pr of i l e- def aul t - WM3700- nat - pool - pool 1) The following table summarizes NAT pool commands Command Description Reference address Specifies addresses for the NAT pool page 8-629 no Negates a command or sets its default page 8-630 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 629 address nat-pool Configures NAT pool IP addresses Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax address [<IP>|range] address range <Start-IP> <End-IP> Parameters address [<IP>|range <START-IP> <END-IP>] Example wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)#address range 172. 16.10.2 172.16.10.8 wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)#s wm3400-34710C8config-profile-default-WM3700-nat-pool-pool1)#show context ip nat pool pool1 address range 172.16.10.2 172.16.10.8 wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)# address <IP> Adds a single IP address to the NAT pool range <START-IP> <END-IP> Adds multiple IP (a range of IP addresses) addresses to the NAT pool <START-IP> Specify the starting IP address of the range. <END-IP> Specify the ending IP address of the range. no Disables NAT pool IP addresses
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 630 no nat-pool Negates a command or sets its default Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 Syntax no address Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-profile-default-WM3700-nat-pool-pool1)#no address Related Commands address Specifies addresses for the NAT pool
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 631 interface Creating Profiles Selects an interface to configure This command is used to enter the interface configuration mode for the specified physical wireless controller SVI interface. If the VLANx (SVI) interface does not exist, its automatically created. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax interface [<INTERFACE>|fe <1-4>|ge <1-8>|me1|port-channel<1-4>|radio [1|2|3]| up1|vlan <1-4094>|wwan1] Parameters interface [<interface>|ge <1-8>|me1|port-channel <1-4|vlan <1-4094>] <INTERFACE> Defines the name of an interface fe <1-4> Sets a FastEthernet interface <1-4> Specify the interface index from 1 - 4. ge <1-8> Sets a GigabitEthernet interface <1-8> Specify the interface index from 1 - 8. (4 for WM3700 and 8 for WM3600). me1 Sets a management interface Not applicable for WM3400 port-channel <1-4> Sets the port channel interface <1-4> Specify the interface index from 1 - 4. radio [1|2|3] Sets a radio interface 1 Selects radio interface 1 2 Selects radio interface 2 3 Selects radio interface 3 up1 Configures the uplink GigabitEthernet interface vlan <1-4094> Configures a VLAN interface <1-4094> Specify the SVI VLAN ID from 1 - 4094.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 632 Example wm3400-34710C8(config-profile-default-WM3700)#interface vlan 44 wm3400-34710C8(config-profile-default-WM3700-if-vlan44)#? SVI configuration commands: crypto Encryption module description Vlan description dhcp-relay-incoming Allow on-board DHCP server to respond to relayed DHCP packets on this interface ip Interface Internet Protocol config commands no Negate a command or set its defaults shutdown Shutdown the selected interface use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-WM3700-if-vlan44)# Related Commands wwan1 Configures a Wireless WAN interface no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 633 Interface Config Instance Use the (config-profile-default-WM3700) instance to configure the Ethernet, VLAN and tunnel associated with the wireless controller. To switch to this mode, use the following command: wm3400-34710C8(config-profile-default-WM3700)#interface [<INTERFACE>|fe <1-4>| ge <1-8>|me1|port-channel <1-4>|radio [1|2|3]|up1|vlan <1-4094>|wwan1] wm3400-34710C8(config-profile-default-WM3700)# ge 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)#? Interface Configuration commands: cdp Cisco Discovery Protocol channel-group Channel group commands description Interface specific description dot1x 802.1X Authentication duplex Set duplex to interface ip Internet Protocol (IP) lldp Link Local Discovery Protocol no Negate a command or set its defaults qos Quality of service shutdown Shutdown the selected interface spanning-tree Spanning tree commands speed Configure speed switchport Set switching mode characteristics use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile-default-WM3700-if-ge1)# The following table summarizes the interface config commands Command Description Reference cdp Enables the Cisco Discovery Protocol (CDP) on ports page 8-635 channel-group Configures channel group commands page 8-636 description Creates an interface specific description page 8-637 dot1x Configures 802.1X authentication settings page 8-638 duplex Specifies the duplex mode for the interface page 8-640 ip Sets the IP address for the assigned Fast Ethernet interface (ME) and VLAN interface page 8-642 lldp Configures Link Local Discovery Protocol (LLDP) page 8-644
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 634 no Negates a command or sets its defaults page 8-645 qos Enables QoS page 8-647 shutdown Disables the selected interface page 8-649 spanning-tree Configures spanning tree parameters page 8-650 speed Specifies the speed of a FastEthernet or GigabitEthernet port page 8-653 switchport Sets interface switching mode characteristics page 8-655 use Defines the settings to use with this command page 8-657 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 635 cdp Interface Config Instance Enables CDP on wireless controller ports Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax cdp [transmit|receive] Parameters cdp [receive|transmit] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#cdp transmit wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands transmit Enables CDP packet snooping on an interface receive Enables CDP packet transmission on an interface no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 636 channel-group Interface Config Instance Configures channel group commands Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax channel-group <1-5> Parameters channel-group <1-5> Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands <1-5> Specifies a channel group number from 1 - 5 no Disables or reverts interface settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 637 description Interface Config Instance Defines an interface description Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax description [<LINE>|<WORD>] Parameters description [<LINE>|<WORD>] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#description This is GigabitEthernet interface for Royal King wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 description This\ is\ GigabitEthernet\ interface\ for\ Royal\ King ip dhcp trust qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands [<LINE>|<WORD>] Defines an interface description no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 638 dot1x Interface Config Instance Configures 802.1X authentication settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dot1x username <USERNAME> password [0 <WORD>|2 <WORD>|<WORD>] Parameters dot1x [username <USERNAME> password [0 <WORD>|2 <WORD>|<WORD>]] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#dot1x username Bob password extremenetworks wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 description This\ is\ GigabitEthernet\ interface\ for\ Royal\ King dot1x username Bob password 0 extremenetworks ip dhcp trust qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# username <USERNAME> Sets the username for authentication <USERNAME> Specify the username. password [0 <WORD>| 2 <WORD>|<WORD>] Sets the password. Select any one of the following options: 0 <WORD> Sets a clear text password 2 <WORD> Sets an encrypted password <WORD> Specify the password.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 639 Related Commands no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 640 duplex Interface Config Instance Specifies duplex mode for an interface Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax duplex [auto|half|full] Parameters duplex [auto|half|full] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#duplex full wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 description This\ is\ GigabitEthernet\ interface\ for\ Royal\ King duplex full dot1x username Bob password 0 extremenetworks ip dhcp trust qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# auto Enables automatic duplexity on an interface port. The port automatically detects whether it should run in full or half-duplex mode. half Sets the port to half-duplex mode. Allows communication in both directions, but only in one direction at any given time full Sets the port to full-duplex mode. Allows flow in both directions simultaneously
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 641 Related Commands no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 642 ip Interface Config Instance Sets the ARP and DHCP components for this interface Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [arp|dhcp] ip [arp [header-mismatch-validation|trust]|dhcp trust] Parameters ip [arp [header-mismatch-validation|trust]|dhcp trust] arp [header-mismatch- validation|trust] Sets ARP for the packets on this interface header-mismatch-validation Verifies mismatch for source MAC address in ARP header and Ethernet header trust Sets ARP trust state for ARP responses on this interface dhcp trust Uses a DHCP client to obtain an IP address for the interface (this enables DHCP on a layer 3 SVI) trust Sets DHCP trust state for DHXP responses on this interface
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 643 Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#ip dhcp trust wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#ip arp header-mismatch- validation wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 description This\ is\ GigabitEthernet\ interface\ for\ Royal\ King duplex full dot1x username Bob password 0 extremenetworks ip dhcp trust ip arp header-mismatch-validation qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 644 lldp Interface Config Instance Configures Link Local Discovery Protocol (LLDP) parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax lldp [receive|transmit] Parameters lldp [receive|transmit] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#lldp transmit wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands [receive] Enables LLDP Protocol Data Units (PDUs) snooping on this interface transmit Enables LLDP PDUs transmission on this interface no Disables or reverts interface settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 645 no Interface Config Instance Negates a command or sets its defaults Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [cdp|channel-group|description|dot1k|duplex|ip|lldp|qos|shutdown|spanning-tree| speed|switchport|use] Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#no cdp wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#no duplex wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands cdp Enables the Cisco Discovery Protocol (CDP) on ports channel-group Configures channel group commands description Creates an interface specific description dot1x Configures 802.1X authentication settings duplex Specifies the duplex mode for the interface
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 646 ip Sets the IP address for the assigned Fast Ethernet interface (ME) and VLAN interface lldp Configures Link Local Discovery Protocol (LLDP) no Negates a command or sets its defaults qos Enables QoS shutdown Disables the selected interface spanning-tree Configures spanning tree parameters speed Specifies the speed of a FastEthernet or GigabitEthernet port switchport Sets interface switching mode characteristics use Defines the settings to use with this command write Writes information to memory or terminal
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 647 qos Interface Config Instance Enables Quality of Service (QoS) Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax qos trust [802.1p|cos|dscp] Parameters qos trust [802.1p|cos|dscp] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#qos trust dscp wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#qos trust dscp wm3400-34710C8(config-profile-default-WM3700-if-ge1)#show context interface ge1 description This\ is\ GigabitEthernet\ interface\ for\ Royal\ King duplex full dot1x username Bob password 0 extremenetworks ip dhcp trust ip arp header-mismatch-validation qos trust dscp qos trust 802.1p channel-group 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# trust [802.1p|cos|dscp] Trusts QoS values ingressing on this interface 802.1p Trusts 802.1p QoS cos Trusts 802.1p QoS dscp Trusts IP DSCP QoS
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 648 Related Commands no Disables or reverts interface settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 649 shutdown Interface Config Instance Shutdown (disables) an interface. The interface is administratively enabled unless explicitly disabled using this command. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax shutdown Parameters None Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#shutdown wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 650 spanning-tree Interface Config Instance Configures spanning tree parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax spanning-tree [bpdufilter|bpduguard|edgeport|force-version|guard|link-type|mst| port-cisco-interoperability|portfast] spanning-tree [edgeport|force-version <0-3>|guard root|portfast] spanning-tree [bpdufilter|bpduguard] [default|disable|enable] spanning-tree link-type [point-to-point|shared] spanning-tree mst <0-15> [cost <1-200000000>|port-priority <0-240>] spanning-tree port-cisco-interoperability [disable|enable] Parameters spanning-tree [edgeport|force-version|guard root|portfast] edgeport Enables an interface as an edge port force-version <0-3> Specifies the spanning tree force version. A version identifier of less than 2 enforces the spanning tree protocol. Select one of the following versions: 0 Spanning Tree Protocol (STP) 1 Not supported 2 Rapid Spanning tree Protocol (RSTP) 3 Multiple Spanning Tree Protocol (MSTP) The default is MSTP
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 651 spanning-tree [bpdufilter|bpduguard] [default|disable|enable] spanning-tree link-type [point-to-point|shared] spanning-tree mst <0-15> [cost <1-200000000>|port-priority <0-240>] spanning-tree port-cisco-interoperability [disbale|enable]] guard root Enables Root Guard for the port. The Root Guard disables reception of superior Bridge Protocol Data Units (BPDUs). The Root Guard ensures the enabled port is a designated port. If the Root Guard enabled port receives a superior BPDU, it moves to a discarding state. Use the no parameter with this command to disable the Root Guard. portfast Enables rapid transitions. Enabling PortFast allows the port to bypass the listening and learning states bpdufilter [default|disable|enable] Sets a PortFast BPDU filter for the port Use the no parameter with this command to revert the port BPDU filter to its default. The spanning tree protocol sends BPDUs from all ports. Enabling the BPDU filter ensures PortFast enabled ports do not transmit or receive BPDUs. bpduguard [default|disable|enable] Enables or disables BPDU guard on a port Use the no parameter with this command to set BPDU guard to its default. When the BPDU guard is set for a bridge, all PortFast-enabled ports that have the BPDU guard set to default shut down the port upon receiving a BPDU. If this occurs, the BPDU is not processed. The port can be brought back either manually (using the no shut down command), or by configuring the errdisable- timeout to enable the port after the specified interval. link-type [point-to-point|shared] Enables or disables point-to-point or shared link types point-to-point Enables rapid transition shared Disables rapid transition mst <0-15> Configures MST on a spanning tree cost <1-200000000> Defines path cost for a port from 1 - 200000000. port-priority <0-240> Defines port priority for a bridge from 1 - 240. port-cisco-interoperability Enables or disables interoperability with Cisco's version of MSTP (which is incompatible with standard MSTP) enable Enables CISCO Interoperability disable Disables CISCO Interoperability. The default is disabled.
TM 4000 Series Access Point CLI Reference Guide 653 speed Interface Config Instance Specifies the speed of a FastEthernet (10/100) or GigabitEthernet (10/100/1000) port Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax speed [10|100|1000|auto] Parameters speed [10|100|1000|auto] Usage Guidelines Set the interface speed to auto detect and use the fastest speed available. Speed detection is based on connected network hardware Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#speed 10 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#speed auto wm3400-34710C8(config-profile-default-WM3700-if-ge1)# 10 Forces 10 Mbps operation 100 Forces 100 Mbps operation 1000 Forces 1000 Mbps operation auto Port automatically detects its operational speed based on the port at the other end of the link. Auto negotiation is a requirement for using 1000BASE-T[3] according to the standard
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 654 Related Commands no Disables or reverts interface settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 655 switchport Interface Config Instance Sets switching mode characteristics for the selected interface Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax swi t chpor t [ access| mode| t r unk] swi t chpor t access vl an <1- 4094> switchport mode [access|trunk] switchport trunk [allowed|native] switchport trunk allowed vlan [<VLAN-ID>|add <VLAN-ID>|none|remove <VLAN-ID>] switchport trunk native [tagged|vlan <1-4094>] Parameters switchport access vlan <1-4094> switchport mode [access|trunk] access vlan <1-4094> Configures access VLAN of an access-mode port vlan Sets the VLAN when interface is in access mode <1-4094> Specify the SVI VLAN ID from 1 - 4094. mode [access|trunk] Sets the interface mode to access or trunk (can only be used on physical - layer 2 - interfaces) access If access mode is selected, the access VLAN is automatically set to VLAN1. In this mode, only untagged packets in the access VLAN (vlan1) are accepted on this port. All tagged packets are discarded trunk If trunk mode is selected, tagged VLAN packets are accepted. The native VLAN is automatically set to VLAN1. Untagged packets are placed in the native VLAN by the wireless controller. Outgoing packets in the native VLAN are sent untagged. t r unk is the default mode for both ports.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 656 switchport trunk allowed vlan [<VLAN-ID>|add <VLAN-ID>|none|remove <VLAN-ID>] switchport trunk native [tagged|vlan <1-4094>] Usage Guidelines Interfaces ge1-ge4 can be configured as trunk or in access mode. An interface (when configured as trunk) allows packets (from the given list of VLANs) to be added to the trunk. An interface configured as access allows packets only from native VLANs Use the [ no] swi t chpor t ( access| mode| t r unk) to undo switchport configurations Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#switchport trunk native tagged wm3400-34710C8(config-profile-default-WM3700-if-ge1)# wm3400-34710C8(config-profile-default-WM3700-if-ge1)#switchport access vlan 1 wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands trunk Sets trunking mode characteristics of the port allowed Configures trunk characteristics when the port is in trunk mode vlan [<VLAN-ID>| add <VLAN-ID>| none| remove <VLAN-ID> Sets allowed VLAN options. The options are: <VLAN-ID> Allows a group of VLAN IDs. Can be either a range of VLAN (55-60) or a list of comma separated IDs (35, 41 etc.) none Allows no VLANs to Xmit/Rx through the layer 2 interface add <VLAN-ID> Adds VLANs to the current list <VLAN-ID> Specify VLAN IDs. Can be either a range of VLAN (55-60) or list of comma separated IDs (35, 41 etc.) remove <VLAN-ID> Removes VLANs from the current list <VLAN-ID> Specify VLAN IDs. Can be either a range of VLAN (55-60) or list of comma separated IDs (35, 41 etc.) trunk Sets trunking mode characteristics of the switchport native [tagged|vlan <1-4094>] Configures the native VLAN ID of the trunk-mode port tagged Tags the native VLAN vlan <1-4094> Sets the native VLAN for classifying untagged traffic when the interface is in trunking mode. Specify a value from 1 - 4094. no Disables or reverts interface settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 657 use Interface Config Instance Specifies the IP access list and MAC access list used with this interface Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [ip-access-list in <IP-ACCESS-LIST>|mac-access-list in <MAC-ACCESS-LIST>] Parameters use [ip-access-list in <IP-ACCESS-LIST>|mac-access-list in <MAC-ACCESS-LIST>] Example wm3400-34710C8(config-profile-default-WM3700-if-ge1)#use mac-access-list in test wm3400-34710C8(config-profile-default-WM3700-if-ge1)# Related Commands ip-access-list in <IP-ACCESS-LIST> Uses an IP access list in Applies ACL on incoming packets <IP-ACCESS-LIST> Specify the IP access list name. mac-access-list in <MAC-ACCESS-LIST> Uses a MAC access list in Applies ACL on incoming packets <MAC-ACCESS-LIST> Specify the MAC access list name. no Disables or reverts interface settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 658 Interface vlan Instance Use (config-profile-default-WM3700) to configure Ethernet, VLAN and tunnel settings. To switch to this mode: wm3400-34710C8(config-profile-default-WM3700)#interface [<INTERFACE>|ge <1-8>| me1|port-channel <1-4>|vlan <1-4094>] wm3400-34710C8(config-profile-default-WM3700)#interface vlan 8 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# The following table summarizes interface VLAN mode commands Commands Description Reference crypto Defines the encryption module page 8-659 description Defines the VLAN description page 8-660 dhcp-relay-incoming Allows an on-board DHCP server to respond to relayed DHCP packets on this interface page 8-661 ip Configures Internet Protocol (IP) config commands page 8-662 no Negates a command or sets its default page 8-664 shutdown Shuts down an interface page 8-667 use Defines the settings used with this command page 8-668 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 659 crypto Interface vlan Instance Sets encryption module for this VLAN interface. The encryption module (crypto map) is configured using the crypto map command. For more information, see crypto. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax crypto map <CRYPTO-MAP> Parameters crypto map <CRYPTO-MAP> Example wm3400-34710C8(config-profile-default-WM3700)#interface vlan 8 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#crypto map map1 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 crypto map map1 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands map <CRYPTO-MAP> Attaches a crypto map to the VLAN interface <CRYPTO-MAP> Specify the crypto map name. no Disables or reverts interface VLAN settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 660 description Interface vlan Instance Defines a VLAN interface description. Use this command to provide additional information about the VLAN. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax description <WORD> Parameters description <WORD> Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#description This VLAN interface is configured for the Sales Team wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8config-profile-default-WM3700-if-vlan8)#show context interface vlan8 description This\ VLAN\ interface\ is\ configured\ for\ the\ Sales\ Team crypto map map1 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands description <WORD> Defines the VLAN interface description no Disables or reverts interface VLAN settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 661 dhcp-relay-incoming Interface vlan Instance Allows an on-board DHCP server to respond to relayed DHCP packets Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-relay-incoming Parameters None Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#dhcp-relay-incoming wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 description This\ VLAN\ interface\ is\ configured\ for\ the\ Sales\ Team crypto map map1 dhcp-relay-incoming wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands no Disables or reverts interface VLAN settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 662 ip Interface vlan Instance Configures VLAN interface IP configuration commands Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [address|dhcp|helper-address|nat] ip helper-address <IP> ip address [<IP/M>|dhcp|zerconf] ip address [<IP/M> {secondary}|zeroconf {secondary}] ip dhcp client request options all ip nat [inside|outside] Parameters ip helper-address <IP> ip address [<IP/M> {secondary}|dhcp|zerconf {secondary}] helper-address <IP> Enables DHCP and BOOTP forwarding for a set of clients. Configure a helper address on the VLAN interface connected to the client. The helper address should specify the address of the BOOTP or DHCP servers. If you have multiple servers, configure one helper address for each server. <IP> Specify the IP address of the DHCP or BOOTP server. address Sets the IP address for this VLAN interface. Select one of the following options to set or obtain the IP address: <IP/M> {secondary} Specify the interface IP address in the A.B.C.D/M format. secondary Optional. Sets the specified IP address as a secondary address dhcp Uses a DHCP client to obtain an IP address for this interface
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 663 ip dhcp client request options all ip nat [inside|outside] Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#ip address 10.0.0.1/8 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#ip nat inside wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#ip helper-address 172.16 .10.3 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#ip dhcp client request o ptions all wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 description This\ VLAN\ interface\ is\ configured\ for\ the\ Sales\ Team ip address 10.0.0.1/8 ip dhcp client request options all ip helper-address 172.16.10.3 ip nat inside crypto map map1 dhcp-relay-incoming wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands zerconf {secondary} Uses Zero Configuration Networking (zerconf) to generate an IP address for this interface secondary Optional. Sets the generated IP address as a secondary address dhcp Uses a DHCP client to configure a request on this VLAN interface client Configures a DHCP client request Configures DHCP client request options Configures DHCP client request options all Configures all DHCP client request options nat [inside|outside] Sets the NAT of this VLAN interface inside Sets the NAT inside interface outside Sets the NAT outside interface no Disables or reverts interface VLAN settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 664 no Interface vlan Instance Negates a command or sets its default values. The no command, when used in the Config Interface VLAN mode, negates VLAN interface settings or reverts them to their default values. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [crypto|description|dhcp-relay-incoming|ip|shut-down|use] no [crypto map|description|dhcp-relay-incoming|shut-down|use <IP-ACCESS-LIST> in] no ip [address|dhcp|helper-address|nat] no ip [helper-address <IP>|nat] no ip address [<IP/M> {secondary}|dhcp|zerconf {secondary}] no ip dhcp client request options all Parameters no [crypto map|description|dhcp-relay-incoming|shut-down|use <IP-ACCESS-LIST> in] no ip address [<IP/M> {secondary}|dhcp|zerconf {secondary}] no crypto map Detaches crypto map from an interface no description Removes the VLAN interface description no dhcp-relay-incoming Prohibits an on board DHCP server from responding to relayed DHCP packets no shut-down If an interface has been shutdown, use the no shutdown command to enable the interface. Use this command for trouble shooting new interfaces. no use <IP-ACCESS-LIST> in Removes specified IP access list from being used by an interface in Disables incoming packets <IP-ACCESS-LIST> Specify the IP access list name. no ip address Disables interface IP settings address Removes IP addresses configured for this interface, depending on the options used while setting the address
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 665 no ip address [helper-address <IP>|nat] no ip address dhcp client request options all IP/M> {secondary} Specify the interface IP address in the A.B.C.D/M format. secondary Optional. Removes the secondary IP address dhcp Removes IP address obtained using the DHCP client zerconf {secondary} Removes the IP address generated using a zerconf secondary Optional. Removes the secondary IP address no ip address Disables interface IP settings address Removes IP addresses configured for this interface, depending on the options used while setting the address helper-address <IP> Disables the forwarding of DHCP and BOOTP packets to the configured helper IP address <IP> Specify the IP address of the DHCP or BOOTP server. nat Disables NAT for this interface ip address Disables interface IP settings address Removes IP addresses configured for this interface, depending on the options used while setting the address dhcp Removes DHCP client request configured for this interface client Removes a DHCP client request Removes DHCP client request options Removes DHCP client request options all Removes all DHCP client request options
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 666 Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no use ip-access-list in wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no allow-management wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no crypto map wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no description wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no dhcp-relay-incoming wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#no ip dhcp client request options all wm3400-34710C8(config-profile-default-WM3700-if-vlan8) wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 ip address 10.0.0.1/8 ip helper-address 172.16.10.3 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands crypto Defines the encryption module description Defines the VLAN description dhcp-relay-incoming Allows an on-board DHCP server to respond to relayed DHCP packets on this interface ip Configures Internet Protocol (IP) config commands no Negates a command or sets its default shutdown Shuts down an interface use Defines the settings used with this command
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 667 shutdown Interface vlan Instance Shuts down the selected interface. Use the no shut down command to enable an interface. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax shutdown Parameters None Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#shutdown wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 ip address 10.0.0.1/8 ip helper-address 172.16.10.3 shutdown wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands no Disables or reverts interface VLAN settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 668 use Interface vlan Instance Specifies an IP access list to use with this VLAN interface Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use ip-access-list in <IP-ACCESS-LIST> Parameters use ip-access-list in <IP-ACCESS-LIST> Example wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#use ip-access-list in test wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#s wm3400-34710C8(config-profile-default-WM3700-if-vlan8)#show context interface vlan8 ip address 10.0.0.1/8 use ip-access-list in test ip helper-address 172.16.10.3 wm3400-34710C8(config-profile-default-WM3700-if-vlan8)# Related Commands ip-access-list in <IP-ACCESS-LIST> Uses a specified IP access list with this interface in Sets incoming packets <IP-ACCESS-LIST> Specify the IP access list name. no Disables or reverts interface VLAN settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 669 led Creating Profiles Turns LEDs on or off on an access point Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax led Parameters None Example wm3400-34710C8(config-profile-default-WM3700)#led % Error: led configuration not available for this platform wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 670 legacy-auto-downgrade Creating Profiles Enables device firmware to auto downgrade when legacy devices are detected Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax legacy-auto-downgrade Parameters None Example wm3400-34710C8(config-profile-default)#legacy-auto-downgrade wm3400-34710C8(config-profile-default)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 671 legacy-auto-update Creating Profiles Auto updates an AP4600 or an AP4700 legacy access point firmware Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax legacy-auto-update {ap4600|ap4700} image <FILE> Parameters legacy-auto-update {ap4600|ap4700} image <FILE> Example wm3400-34710C8(config-profile-default-WM3700)#legacy-auto-update AP-4600 image flash:/ap47d.img wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#legacy-auto-update wm3400-34710C8(config-profile-default-WM3700)# Related Commands legacy-auto-update Updates an AP4600 or an AP4700 legacy access point firmware [ap4600|ap4700] image <FILE> Select one of the following options: ap4600 Auto updates a legacy AP4600 firmware ap4700 Auto updates a legacy AP4700 firmware The following are common to both the AP4600 and AP4700 parameters: image Sets the path to the firmware image <FILE> Specify the path and filename in the flash:/ap.img format. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 672 lldp Creating Profiles Configures Link Layer Discovery Protocol (LLDP) settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax lldp [holdtime|med-tlv-select|run|timer] lldp [holdtime <10-1800>|run|timer <5-900>] lldp med-tlv-select [inventory-management|power-management] Parameters lldp [holdtime <10-1800>|run|timer <5-900>] lldp med-tlv-select [inventory-management|power-management] holdtime <10-1800> Sets the holdtime for transmitted LLDP PDUs. This command specifies the amount of time a receiving device should hold information before discarding it <10-1800> Specify a holdtime from 10 - 1800 seconds. run Enables run LLDP timer <5-900> Sets timer for transmit interval. This command specifies the transmission frequency of LLDP updates in seconds <5-900> Sets transmit interval from 5 - 900 seconds. med-tlv-select [inventory-management| power-management] Provides additional media endpoint device TLVs to enable discovery of inventory and power management. Specifies the LLDP MED TLVs to send or receive. inventory-management Enables inventory management discovery. Allows an endpoint to convey detailed inventory information about itself to the wireless controller power-management Enables extended power via MDI discovery. Allows wireless controllers to convey power information, such as how the device is powered, power priority etc.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 673 Example WM3400-880DA7(config-profile-default-WM3400)#lldp timer 20 WM3400-880DA7(config-profile-default-WM3400)# Related Commands no Disables or reverts settings to their default
TM 4000 Series Access Point CLI Reference Guide 675 Parameters load-balancing advanced-params [2.4GHz|5GHz|ap-load] [client-weightage| throughput-weightage] <0-100> load-balancing advanced-params equality-margin [2.4GHz|5GHz|ap|band] <0-100> load-balancing advanced-params hiwater-threshold [ap|channel-2.4GHz| channel-5GHz] <0-100> advanced-params Configures advanced load balancing parameters 2.4GHz-load [client-weightage| throughput-weightage] <0-100> Configures 2.4GHz radio load calculation weightages client-weightage Specifies weightage assigned to the client-count when calculating the 2.4GHz radio load throughput-weightage Specifies weightage assigned to throughput, when calculating the 2.4GHz band, channel, or radio load The following is common to the client-weightage and throughput-weightage parameters: <0-100> Sets the margin as a percentage of load from 1 - 100 5GHz-load [client-weightage| throughput-weightage] <0-100> Configures 5GHz radio load calculation weightages client-weightage Specifies weightage assigned to the client-count when calculating the 5GHz radio load throughput-weightage Specifies weightage assigned to throughput, when calculating the 5GHz band, channel or radio load The following is common to the client-weightage and throughput-weightage parameters: <0-100> Sets the margin as a percentage of load from 1 - 100 ap-load [client-weightage| throughput-weightage] <0-100> Configures AP load calculation weightages client-weightage Specifies weightage assigned to the client-count when calculating the AP load throughput-weightage Specifies weightage assigned to throughput, when calculating the AP load The following is common to the client-weightage and throughput-weightage parameters: <0-100> Sets the margin as a percentage of load from 1 - 100 advanced-params Configures advanced load balancing parameters equality-margin [2.4GHz|5GHz|ap|band] <0-100> Configures the maximum load difference considered equal. The load is compared for different 2.4GHz channels, 5GHz channels, AP, or bands. 2.4GHz Configures the maximum load difference considered equal when comparing loads on different 2.4GHz channels 5GHz Configures the maximum load difference considered equal when comparing loads on different 5GHz channels ap Configures the maximum load difference considered equal when comparing loads on different APs band Configures the maximum load difference considered equal when comparing loads on different bands The following is common to 2.4GHz channels, 5GHz channels, APs, and bands: <0-100> Sets the margin as a percentage of load from 1 - 100 advanced-params Configures advanced load balancing parameters
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 676 load-balancing advanced-params max-preferred-band-load [2.4GHGz|5GHzd] <0-100> load-balancing advanced-params [max-neighbors <0-16>|min-common-clients <0-256>| min-neighbor-rssi <0-100>|min-probe-rssi <0-100>] load-balancing [balance-ap-loads|balance-band-loads|balance-channel-loads [2.4GHz|5GHz]] hiwater-threshold Configures the load beyond which load balancing is invoked [ap|channel-2.4GHz| channel-5GHz] <0-100> Select one of the following options: ap Configures the load beyond which load balancing begins, for an APs total load channel-2.4GHz Configures the load beyond which load balancing begins, for an APs channel on 2.4GHz channel-5GHz Configures the load beyond which load balancing begins, for an APs channel on 5GHz The following is common for the AP, channel-2.4GHz, and channel 5GHz parameters: <0-100> Sets the threshold as a number from 1 - 100 advanced-params Configures advanced load balancing parameters max-preferred-band-load Configures the maximum load on the preferred band, beyond which the other band is equally preferred [2.4GHz|5GHz] <0-100> Select one of the following options: 2.4GHz Configures the maximum load on 2.4GHz, when it is the preferred band 5GHz Configures the maximum load on 5GHz, when it is the preferred band The following is common to the 2.4GHz and 5GHz bands: <0-100> Configures the maximum load as a percentage from 0 - 100 advanced-params Configures advanced load balancing parameters max-neighbors <0-6> Configures the maximum number of confirmed neighbors to balance <0-6> Specify a value from 0 - 6. Optionally configure a minimum of 0 neighbors and a maximum of 6 neighbors min-common-clients <0-256> Configures the minimum number of common clients that can be shared with the neighbor for load balancing <0-256> Specify a value from 0 - 256. Optionally configure a minimum of 0 clients and a maximum of 256 clients. min-neighbor-rssi <0-100> Configures the minimum signal strength (Received Signal Strength Indicator - RSSI) of a neighbor detected <0-100> Sets the signal strength as a number. Specify a value from 0 - 100. min-probe-rssi <0-100> Configures the minimum received signal strength of probe required to qualify the sender as a common client <0-100> Sets the signal strength as a number. Specify a value from 0 - 100. balance-ap-loads Enables neighbor AP load balancing balance-band-loads Enables balancing of the total band load amongst neighbors
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 677 load-balancing band-ratio [2.4GHz|5GHz] [0|<1-10>] load-balancing band-steering-strategy [disable|steer-by-ratio|steer-to-2.4GHz| steer-to-5GHz] load-balancing neighbor-selection-strategy [use-common-clients| use-roam-notification|use-smart-rf|use-wips] balance-channel-loads [2.4GHz|5GHz] Enables the following: 2.4GHz Balances channel loads on 2.4GHz bands 5GHz Balances channel loads on 5GHz bands band-ratio Configures the relative loading of 2.4GHz and 5GHz bands 2.4GHz [0|<1-10>] Configures the relative loading of 2.4GHz bands 0 Selecting 0 steers all dual-band clients preferentially to the other band <0-10> Configures a relative load as a number from 0 - 10 5ghz [0|<1-10>] Configures the relative loading of 5GHz bands 0 Selecting 0 steers all dual-band clients preferentially to the other band <0-10> Configures a relative load as a number from 0 - 10 band-steering-strategy Configures a band steering strategy. The options are: disable, steer-by-ratio, steer-to-2.4GHz, and steer-to-5GHz disable Disables band steering steer-by-ratio Steers wireless clients to either band according to the band ratio set steer-to-2.4GHz Steers all dual-band clients to the 2.4GHz band steer-to-5GHz Steers all dual-band clients to the 5GHz band neighbor-selection-strategy Configures a neighbor selection strategy. The options are: use-common-clients, use-roam-notification, use-smart-rf, and use-wips use-common-clients Configures probes from common clients use-roam-notification Configures roam notification from roaming clients use-smart-rf Configures neighbors detected use-wips Configures WIPS to select neighbors
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 678 Example wm3400-34710C8(config-profile-default-WM3700)#load-balancing advanced-params 2.4ghz- load throughput-weightage 90 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#load-balancing advanced-params hiwater-threshold ap 90 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#load-balancing balance-ap-loads wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#load-balancing neighbor-selection -strategy use-common-clients wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show context profile wm3400 default-wm3400 autoinstall configuration autoinstall firmware load-balancing advanced-params 2.4ghz-load throughput-weightage 90 load-balancing band-ratio 5ghz 0 load-balancing advanced-params hiwater-threshold ap 90 crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp qos trust 802.1p interface ge4 ip dhcp trust --More-- wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 679 logging Creating Profiles Enables message logging and configures logging settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax logging [aggregation-time|buffered|console|facility|forward|host|on|syslog] logging [aggregation-time <1-60>|host <IP>|on] logging [buffered|console|syslog|forward] [<0-7>|alerts|critical|debugging emergencies|errors|informational|notifications|warnings] logging facility [local0|local1|local2|local3|local4|local5|local16|local7] Parameters logging [aggregation-time <1-60>|host <IP>|on] logging [buffered|console|syslog|forward] [<0-7>|alerts|critical|debugging emergencies|errors|informational|notifications|warnings] aggregation-time <1-60> Sets the number of seconds for aggregating repeated messages <1-60> Specify a value from 1 - 60 seconds. host <IP> Configures a remote host to receive log messages <IP> Specify the IP address of the remote host. on Enables the logging of system messages buffered Sets the buffered logging level console Sets the console logging level syslog Sets the syslog servers logging level forward Forwards system debug messages to the wireless controller
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 680 logging facility [local0|local1|local2|local3|local4|local5|local16|local7] Example wm3400-34710C8(config-profile-default-WM3700)#logging facility local4 wm3400-34710C8(config-profile-default-WM3700)#logging monitor notifications Related Commands [<0-7>|alerts| criticail|debugging| emergencies|errors| informational|notifications|wa rnings] The following are common to the buffered, console, syslog and forward parameters. All incoming messages have different severity levels based on their importance. The severity level is fixed on a scale of 0 - 7. <0-7> Sets the message logging severity level on a scale of 0 - 7 alerts Severity level 1: Requires immediate action critical Severity level 2: Critical conditions debugging Severity level 7: Debugging messages emergencies Severity level 0: System is unusable errors Severity level 3: Error conditions informational Severity level 6: Informational messages notifications Severity level 5: Normal but significant conditions warnings Severity level 4: Warning conditions facility [local0|local1| local2|local3|local4| local5|local6|local7] Enables the syslog to decide where to send the incoming message. There are 8 logging facilities, from syslog0 to syslog7. local0 Syslog facility local0 local1 Syslog facility local1 local2 Syslog facility local2 local3 Syslog facility local3 local4 Syslog facility local4 local5 Syslog facility local5 local6 Syslog facility local6 local7 Syslog facility local7 no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 681 mac-address-table Creating Profiles Configures the MAC address table. Use this command to assign a static address to the MAC address table. AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mac-address-table [aging-time|static] mac-address-table aging-time [0|<10-1000000>] mac-address-table static <MAC> vlan <1-4094> interface [<L2-INTERFACE>| ge <1-4>|port-channel <1-2>] Parameters mac-address-table aging-time [0|<10-1000000>] mac-address-table static <MAC> vlan <1-4094> interface [<L2-INTERFACE>| ge <1-4>|port-channel <1-2>] aging-time [0|<10-1000000>] Sets the duration a learned MAC address persists after the last update 0 Entering the value 0 disables the aging time <10-1000000> Sets the aging time from 10 -100000 seconds static <MAC> vlan <1-4094> <WORD> [WORD| ge <1-4>|me1|pc <1-4>| vlan <1-4094>] Creates a static MAC address table entry <MAC> Specifies the static address to add to the MAC address table. Specify the MAC address in the AA-BB-CC-DD-EE-FF, AA:BB:CC:DD:EE:FF, or AABB.CCDD.EEFF format. vlan <1-4094> Assigns a static MAC address to a specified VLAN port <1-4094> Specify the VLAN index from 1 - 4094.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 682 Example wm3400-34710C8(config-profile-default-WM3700)#mac-address-table static 00-40-96-B0- BA-2A vlan1 ge 1 wm3400-34710C8(config-profile-default-WM3700)# Related Commands interface [<L2-INTERFACE>|ge <1-4>| port-channel <1-2>] Specifies the interface type. The options are: layer 2 Interface, GigabitEthernet interface, and a port channel interface <L2-INTERFACE> Specify the layer 2 interface name. ge Specifies a GigabitEthernet interface <1-4> Specify the GigabitEthernet interface index from 1 - 4. port-channel Specifies a port channel interface <1-2> Specify the port channel interface index from 1 - 2. no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 683 mint Creating Profiles Configures MiNT protocol commands Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mint [dis|level|link|mlcp|spf-latency] mint dis priority-adjustment <-255-255> mint level 1 area-id <1-16777215> mint link [force|ip|listen|vlan] mint link force ip <IP> [<1-65535> level|level] 2 {adjacency-hold-time <2-600>|cost <1-10000>|hello-interval <1-120>} mint link listen ip <IP> {adjacency-hold-time <2-600>|cost <1-10000>| hello-interval <1-120>|level [1|2]} mint link ip <IP> {<1-65535>|adjacency-hold-time <2-600>|cost <1-10000>| hello-interval <1-120>|level [1|2]} mint mlcp [IP|vlan] mint spf-latency <0-60> Parameters mint dis priority-adjustment <-255-255> dis priority-adjustment <-255-255> Sets the relative priority for the router to become DIS (designated router) priority-adjustment Sets adjustment added to base priority <-255-255> The priority adjustment value, added to fixed the base priority (higher numbers result in higher priorities)
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 684 mint level 1 area-id <1-16777215> mint link force ip <IP> [<1-65535> level|level] 2 {adjacency-hold-time <2-600>|cost <1-10000>|hello-interval <1-120>} mint link listen ip <IP> {adjacency-hold-time <2-600>|cost <1-10000>| hello-interval <1-120>|level [1|2]} level 1 Configures local MiNT routing 1 Configures local MiNT routing level area-id <1-16777215> Specifies routing area identifier <1-16777215> Specify a value from 1 - 16777215. link force Creates a MiNT routing link force Forces a MiNT routing link to be created even if not necessary ip <IP> Creates a MiNT tunnel over UDP/IP <IP> Specify IP address of peer <1-65535> level 2 Specifies the peer UDP port to link with the specified IP address level Specifies the routing level 2 Configures inter-site MiNT routing level adjacent-hold-time <2-600> Optional. Specifies the adjacency lifetime after hello packets cease <2-600> Specify a value from 2 - 600 seconds. cost <1-100000> Optional. Specifies the link cost in arbitrary units <1-100000> Specify a value from 1 - 100000. hello-interval <1-120> Optional. Specifies the hello-interval between packets <1-120> Specify a value from 1 - 120. link listen Creates a MiNT routing link listen Creates a MiNT listening link ip <IP> Creates a MiNT listening link over UDP/IP <IP> Specify the IP address of the listening port. adjacent-hold-time <2-600> Optional. Specifies adjacency lifetime after hello packets cease <2-600> Specify a value from 2 - 600 seconds. cost <1-100000> Optional. Specifies link cost in arbitrary units <1-100000> Specify a value from 1 - 100000. hello-interval <1-120> Optional. Specifies the interval between hello packets <1-120> Specify a value from 1 - 120. level [1|2] Optional. Specifies the routing levels for this routing link. The options are: 1 Configures local routing 2 Configures inter-site routing
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 685 mint link ip <IP> {<1-65535>|adjacency-hold-time <2-600>|cost <1-10000>| hello-interval <1-120>|level [1|2]} mint mlcp [IP|vlan] mint spf-latency <0-60> Example wm3400-34710C8(config-profile-default-WM3700)#mint level 1 area-id 88 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8config-profile-default-WM3700)#mint link ip 1.2.3.4 level 1 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show mint links vlan-1 : level 1, cost 10, 1 adjacencies, DIS 70.37.fa.be (self) wm3400-34710C8(config-profile-default-WM3700)#show mint stats 1 L1 neighbors L1 LSP DB size 2 LSPs (1 KB) 2 L1 routes Last SPFs took 0s SPF (re)calculated 6 times. levels 1 base priority 180 dis priority 180 wm3400-34710C8(config-profile-default-WM3700)#show mint route Destination : Next-Hop(s) 00.00.00.00 : 00.00.00.00 70.88.9e.c4 : 70.88.9E.C4 link ip <IP> Creates a MiNT routing link ip Creates a MiNT tunnel over UDP/IP <IP> Specify the IP address of the peer. <1-65535> Select the peer UDP port from 1 - 65535. adjacent-hold-time <2-600> Optional. Specifies the adjacency lifetime after hello packets cease <2-600> Specify a value from 2 - 600 seconds. cost <1-100000> Optional. Specifies the link cost in arbitrary units <1-100000> Specify a value from 1 - 100000. hello-interval <1-120> Optional. Specifies the hello interval between packets <1-120> Specify a value from 1 - 120. level [1|2] Optional. Specifies the routing levels for this routing link. The options are: 1 Configures local routing 2 Configures inter-site routing mlcp [l2|l3] Configures the MiNT Link Creation Protocol (MLCP) l2 Configures MLCP over layer 2 (VLAN) links l3 Configures MLCP over layer 3 (IP) links spf-latency <0-60> Specifies the latency of SPF routing recalculation <0-60> Specify the latency from 0 - 60 seconds.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 686 70.37.fa.be : 70.37.FA.BE wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 687 misconfiguration-recovery-time Creating Profiles Verifies wireless controller connectivity after a configuration is received Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax misconfiguration-recovery-time <60-300> Parameters misconfiguration-recovery-time <60-300> Example wm3400-34710C8(config-profile-default-WM3700)#misconfiguration-recovery-time 65 wm3400-34710C8(config-profile-default-WM3700)# Related Commands <60-300> Sets the recovery time from 60 - 300 seconds no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 688 monitor Creating Profiles Enables critical resource monitoring Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax monitor <IP> ping-mode [arp-icmp|arp-only vlan <1-4094>] Parameters monitor <IP> ping-mode [arp-icmp|arp-only vlan <1-4094>] Example WM3400-880DA7(config-critical-resource-policy-testpolicy)#monitor 172.16.10.112 ping-mode arp-only vlan 1 WM3400-880DA7(config-critical-resource-policy-testpolicy)# WM3400-880DA7(config-critical-resource-policy-testpolicy)#monitor 172.16.10.112 ping-mode arp-icmp WM3400-880DA7(config-critical-resource-policy-testpolicy)# WM3400-880DA7(config-critical-resource-policy-testpolicy)#show context critical-resource-policy testpolicy monitor 172.16.10.112 ping-mode arp-only vlan 1 WM3400-880DA7(config-critical-resource-policy-testpolicy)# monitor <IP> Specifies a critical resource to monitor <IP> Specify the IP address of the critical resource. ping-mode Specifies the protocol used to ping the critical resource arp-icmp Uses either ARP requests, or ICMP echo request to monitor critical resources (requires the AP or wireless controller to have an IP address) arp-only vlan <1-4094> Uses only probing ARP requests to monitor critical resource (suitable for AP or wireless controller without IP address) vlan Specify the VLAN to send ARP requests <1-4094> Specify the SVI VLAN ID from 1 - 4094.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 689 Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 690 neighbor-inactivity-timeout Creating Profiles Configures neighbor inactivity timeout Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax neighbor-inactivity-timeout <1-1000> Parameters neighbor-inactivity-timeout <1-1000> Example wm3400-34710C8(config-profile-default)#neighbor-inactivity-timeout 500 wm3400-34710C8(config-profile-default)# Related Commands <1-1000> Sets a neighbor inactivity timeout <1-1000> Specify a value from 1 - 1000 seconds. no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 691 neighbor-info-interval Creating Profiles Configures the neighbor information exchange interval Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax neighbor-info-interval <1-100> Parameters neighbor-info-interval <1-100> Example wm3400-34710C8(config-profile-default-WM3700)#neighbor-info-interval 6 wm3400-34710C8(config-profile-default-WM3700)# Related Commands <1-100> Sets interval in seconds from 1 - 100 no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 692 no Creating Profiles Negates a command or resets values to their default Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [aaa|adopted-mode|ap-upgrade|arp|auto-learn-staging-config|autoinstall| bridge|cdp|cluster|configuration-persistence|controller|crypto||dscp- mapping| email-notification|events|interface|ip|led|legacy-auto-downgrade| legacy-auto-update|lldp|load-balancing|logging|local|mac-address-table| mint|misconfiguration-recovery-time|monitor|noc|ntp|preferred-controller- group| preferred-tunnel-controller|radius|rf-domain-manager|spanning-tree| tunnel-controller|use|vpn|wep-shared-key-auth|service] Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated Example wm3400-34710C8(config-profile-default-WM3700)#no cluster wm3400-34710C8(config-profile-default-WM3700)# Related Commands ap-upgrade Enables automatic AP firmware upgrade
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 693 arp Configures static address resolution protocol auto-learn-staging- config Enables network configuration learning of devices autoinstall Configures the autoinstall feature bridge Configures bridge specific commands cdp Enables Cisco Discovery Protocol (CDP) on a device cluster Configures a cluster name configuration- persistence Enables persistence of configuration across reloads controller Configures a wireless controller crypto Configures crypto settings dscp-mapping Configures an IP DSCP to 802.1p priority mapping for untagged frames email-notification Configures e-mail notification enforce-version Checks device firmware versions before attempting connection events Displays system event messages interface Configures an interface ip Configures IP components led Turns device LEDs on or off legacy-auto- downgrade Auto downgrades a legacy device firmware legacy-auto- update Auto upgrades a legacy device firmware lldp Configures Link Layer Discovery Protocol (LLDP) load-balancing Configures load balancing parameters logging Modifies message logging mac-address-table Configures the MAC address table mint Configures MiNT protocol misconfiguration- recovery-time Verifies wireless controller connectivity after a configuration is received monitor Enables critical resource monitoring neighbor-inactivity- timeout Configures neighbor inactivity timeout neighbor-info- interval Configures neighbor information exchange interval no Negates a command or sets its default values noc Configures NOC settings ntp Configures an NTP server power-config Configures the power mode preferred-controller- group Specifies the wireless controller group preferred for adoption preferred-tunnel- controller Configures the tunnel controller name radius Configures device-level RADIUS authentication parameters rf-domain-manager Enables RF Domain manager spanning-tree Configures spanning tree commands tunnel-controller Configures the name of tunneled WLAN (extended-vlan) controller
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 694 use Defines the settings used by this feature wep-shared-key- auth Enables support for 802.11 WEP shared key authentication clrscr Clears the display screen commit Commits (saves) changes made in the current session do Runs commands from EXEC mode end Ends and exits the current mode and moves to the PRIV EXEC mode exit Ends the current mode and moves to the previous mode help Displays the interactive help system revert Reverts changes to their last saved configuration service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations show Displays running system information write Writes information to memory or terminal
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 695 noc Creating Profiles Configures Network Operations Center (NOC) settings, such as NOC statistics update interval Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax noc update-interval [<5-3600>|auto] Parameters noc update-interval [<5-3600>|auto] Example WM3400-880DA7(config-profile-default-WM3400)#noc update-interval 25 WM3400-880DA7(config-profile-default-WM3400)# Related Commands update-interval [<5-3600>|auto] Configures NOC statistics update interval <5-3600> Specify the update interval from 5 - 3600 seconds. auto The NOC statistics update interval is automatically adjusted by the wireless controller based on load no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 696 ntp Creating Profiles Configure the Network Time Protocol (NTP) server settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ntp server <IP> {autokey|key|prefer|version} ntp server <IP> {autokey {prefer version <1-4>|version <1-4>}} ntp server <IP> {key <1-65534> md5 [0 <WORD>|2<WORD>|<WORD>]{prefer version <1-4>|version <1-4>}} ntp server <IP> {prefer version <1-4>|version <1-4> prefer} Parameters ntp server <IP> {autokey {prefer version <1-4>|version <1-4>}} ntp server <IP> {key <1-65534> md5 [0 <WORD>|2<WORD>|<WORD>]{prefer version <1-4>|version <1-4>}} server <IP> Configures a NTP server association autokey {prefer version <1-4>}| version <1-4>} Optional. Configures an autokey peer authentication scheme prefer Optional. Prefers this peer when possible version Optional. Configures the NTP version <1-4> Select the NTP version from 1 - 4. server <IP> Configures a NTP server association key <1-65534> Optional. Defines the authentication key for trusted time sources <1-65534> Specify the peer key number. md5 [0 <WORD>| 2 <WORD>|<WORD>] Sets MD5 authentication 0 <WORD> Configures a clear text password 2 <WORD> Configures an encrypted password <WORD> Sets an authentication key
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 697 ntp server <IP> {prefer version <1-4>|version <1-4> prefer} Example wm3400-34710C8(config-profile-default-WM3700)#ntp server 172.16.10.10 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#ntp server 172.16.10.1 version 1 prefer wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#ntp server 172.16.10.9 key md5 0 sharedkey1 prefer version 1 wm3400-34710C8(config-profile-default-WM3700)# Related Commands prefer version <1-4> Optional. Prefers this peer when possible version Optional. Configures the NTP version <1-4> Select the NTP version from 1 - 4. server <IP> Configures a NTP server association prefer {version <1-4>} Optional. Prefers this peer when possible version Optional. Configures the NTP version <1-4> Select the NTP version from 1 - 4. version <1-4> prefer Optional. Configures a NTP version as preferred <1-4> Select the NTP version from 1 - 4. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 698 preferred-controller-group Creating Profiles Specifies the wireless controller group preferred for adoption Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax preferred-controller-group <WORD> Parameters preferred-controller-group <WORD> Example wm3400-34710C8(config-profile-default-WM3700)#preferred-controller-group testgroup1 wm3400-34710C8(config-profile-default-WM3700)# Related Commands <WORD> Specify the name of the wireless controller group preferred for adoption no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 699 preferred-tunnel-controller Creating Profiles Configures the tunnel controller name the system prefers for tunneling extended VLAN traffic Supported in the following platforms: WM3400 WM3600 WM3700 Syntax preferred-tunnel-controller <NAME> Parameters preferred-tunnel-controlelr <NAME> Example wm3400-34710C8(config-profile-default-wm3400)#preferred-tunnel-controller testtunnel wm3400-34710C8(config-profile-default-wm3400)# preferred-tunnel-controller <NAME> Configures the tunnel controller name the system prefers for tunneling extended VLAN traffic
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 700 power-config Creating Profiles Configures the power mode Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax power-config [af-option|at-option|mode] power-config [af-option|at-option] [range|throughput] power-config mode [auto|3af] Parameters power-config [af-option|at-option] [range|throughput] power-config mode [auto|3af] af-option [range|throughput] Configures the af power option. The options are: range Configures the af power range mode. This mode provides higher power but fewer tx chains. throughput Configures the af power throughput mode. This mode provides lower power but has more tx chains. at-option [range|throughput] Configures the at power option. The options are: range Configures the at power range mode. This mode provides higher power but fewer tx chains. throughput Configures the at power throughput mode. This mode provides lower power but has more tx chains. mode [auto|3af] Configures the AP power mode 3af Forces an AP power up at the 3af power mode auto Sets the detection auto mode
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 701 Example wm3400-34710C8(config-profile-defalut-WM3700)#power-config af-option range % Warning: AP must be restarted for power-management change to take effect. wm3400-34710C8(config-profile-defalut-WM3700)# wm3400-34710C8(config-profile-defalut-WM3700)#power-config at-option throughput % Warning: AP must be restarted for power-management change to take effect. wm3400-34710C8(config-profile-defalut-WM3700)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 702 radius Creating Profiles Configures device level RADIUS authentication parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax radius [nas-identifier|nas-port-id] <WORD> Parameters radius [nas-identifier|nas-port-id] <WORD> Example wm3400-34710C8(config-profile-default-WM3700)#radius nas-port-id 1 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8config-profile-default-WM3700)#radius nas-identifier test wm3400-34710C8(config-profile-default-WM3700)# Related Commands nas-identifier <WORD> Specifies the RADIUS Network Access Server (NAS) identifier attribute <WORD> Specifies the NAS identifier nas-port-id <WORD> Specifies the RADIUS NAS port ID attribute <WORD> Specifies the NAS port ID no Disables or reverts settings to their default
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 703 router Creating Profiles Configures dynamic router protocol settings. For more details on router commands, refer Router-Mode Commands Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax router ospf Parameters router ospf Example wm3400-34710C8(config-profile-default-wm3400)#router ospf wm3400-34710C8(config-profile default-wm3400-router-ospf)#? Router OSPF Mode commands: area OSPF area auto-cost OSPF auto-cost default-information Distribution of default information ip Internet Protocol (IP) network OSPF network no Negate a command or set its defaults ospf Ospf passive Make OSPF Interface as passive redistribute Route types redistributed by OSPF route-limit Limit for number of routes handled OSPF process router-id Router ID vrrp-state-check Publish interface via OSPF only if the interface VRRP state is not BACKUP clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes ospf Enables OSPF settings. Changes configuration mode to router mode
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 704 service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-router-ospf)#
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 705 rf-domain-manager Creating Profiles Enables the RF Domain manager Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rf-domain-manager [capable|priority <1-255>] Parameters rf-domain-manager [capable|priority <1-255>] Example wm3400-34710C8(config-profile-default-WM3700)#rf-domain-manager priority 9 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#rf-domain-manager capable wm3400-34710C8(config-profile-default-WM3700)# Related Commands capable Enables a device to become a site manager priority <1-10000> Assigns a priority value for site manager selection <1-255> Select a priority value from 1 - 255. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 706 spanning-tree Creating Profiles Enables spanning tree commands. Use these commands to configure the errdisable, multiple spanning tree and portfast settings. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax spanning-tree [errdisable|mst|portfast] spanning-tree errdisable recovery [cause bpduguard|interval <10-1000000>] spanning-tree mst [<0-15>|cisco-interoperability|enable|forward-time| hello-time|instance|max-age|max-hops|region|revision] spanning-tree mst [<0-15> priority <0-61440>|cisco-interoperability [enable|disable]|enable|forward-time <4-30>|hello-time <1-10>|instance <1- 15>| max-age <6-40>|max-hops <7-127>|region <LINE>|revision <0-255>] spanning-tree portfast [bpdufilter|bpduguard] default Parameters spanning-tree errdisable recovery [cause bpduguard|interval <10-1000000>] errdisable Disables or shutsdown ports where traffic is looping, or ports with traffic in one direction recovery Enables the timeout mechanism for a port to be recovered cause bpduguard Specifies the reason for errdisable bpduguard Recovers from errdisable due to bpduguard interval <10-1000000> Specifies the interval after which a port is enabled <10-1000000> Specify a value from 10 - 1000000 seconds.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 707 spanning-tree mst [<0-15> priority <0-61440>|cisco-interoperability [enable|disable]|enable|forward-time <4-30>|hello-time <1-10>|instance <1-15>| max-age <6-40>|max-hops <7-127>|region <LINE>|revision <0-255>] spanning-tree portfast [bpdufilter|bpduguard] default] mst Configures Multiple Spanning Tree (MST) commands <0-15> priority <0-61440> Specifies the number of instances required to configure MST. Select a value from 0 -15. priority Sets the bridge priority to the specified value. Use the no parameter with this command to restore the default bridge priority value. <0-61440> Sets the bridge priority in increments (Lower priority indicates greater likelihood of becoming root) cisco interoperability [enable|disable] Enables or disables CISCO interoperability enable Enables MST protocol forward-time <4-30> Specifies the forwarding delay time in seconds <4-30> Specify a value from 4 - 30 seconds. hello-time <1-10> Specifies the hello BDPU interval in seconds <1-10> Specify a value from 1 - 10 seconds. instance <1-15> Defines the instance ID to which the VLAN is associated <1-15> Specify an instance ID from 1 - 10. max-age <6-40> Defines the maximum time to listen for the root bridge <6-40> Specify a value from 4 - 60 seconds. max-hops <7-127> Defines the maximum hops when BPDU is valid <7-127> Specify a value from 7 - 127. region <LINE> Specifies the MST region <LINE> Specify the region name. revision <0-255> Sets the MST bridge revision number. This enables the retrieval of configuration information. <0-255> Specify a value from 0 - 255. portfast [bpdufilter| bpduguard] default Enables PortFast on a bridge bpdufilter default Sets the BPDU filter for the port. Use the no parameter with this command to revert to default. The spanning tree protocol sends BPDUs from all ports. Enabling the BPDU filter ensures that PortFast enabled ports do not transmit or receive BPDUs bpduguard default Guards PortFast ports against BPDU receive default Enables the BPDU filter on PortFast enabled ports by default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 708 Usage Guidelines If a bridge does not hear bridge protocol data units (BPDUs) from the root bridge within the specified interval, defined in the max-age (seconds) parameter, assume the network has changed and recomputed the spanning-tree topology. Generally, spanning tree configuration settings in the config mode define the configuration for bridge and bridge instances. MSTP works based on instances. An instance is a group of VLANs with a common spanning tree. A single VLAN cannot be associated with multiple instances. Wireless controllers with the same instance, VLAN mapping, revision number and region names define a unique region. Wireless controllers in the same region exchange bridge protocol data units (BPDUs) with instance record information within. Example wm3400-34710C8(config-profile-default-WM3700)#spanning-tree errdisable recovery cause bpduguard wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#spanning-tree mst 2 priority 4096 wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#show context profile WM3700 default-WM3700 spanning-tree mst 2 priority 4096 spanning-tree errdisable recovery cause bpduguard autoinstall configuration autoinstall firmware crypto isakmp policy default crypto ipsec transform-set default esp-aes-256 esp-sha-hmac interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp qos trust 802.1p interface ge3 ip dhcp trust qos trust dscp qos trust 802.1p interface ge4 ip dhcp trust qos trust dscp --More-- wm3400-34710C8(config-profile-default-WM3700)#
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 709 Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 710 tunnel-controller Creating Profiles Configures the name of tunneled WLAN (extended-vlan) controller Supported in the following platforms: WM3400 WM3600 WM3700 Syntax tunnel-controller <NAME> Parameters tunnel-controller <NAME> Example wm3400-34710C8(config-profile-default-wm3400)#tunnel-controller testgroup wm3400-34710C8(config-profile-default-wm3400)# tunnel-controller <NAME> Configures the name of tunneled WLAN (extended VLAN) controller. Specify a name to configure.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 711 use Creating Profiles Uses pre configured policies with this profile Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax Profiles use [advanced-wips-policy|auto-provisioning-policy|captive-portal| critical-resource-policy|dhcp-server-policy|event-system-policy|firewall- policy| igmp-snoop-policy| management-policy|radius-server-policy|role-policy] Syntax Device Mode use [adoption-policy|advanced-wips-policy| captive-portal|critical-resource-policy|dhcp-server-policy| firewall-policy|igmp-snoop-policy|management-policy|profile| radius-server-policy|rf-domain|role-policy| smart-rf-policy|trustpoint|wips-policy] NOTE The Parameter Table contains the use command parameters for the Profiles and Device modes. ParametersProfiles mode use [advanced-wips-policy|auto-provisioning-policy|captive-portal| critical-resource-policy|dhcp-server-policy|event-system-policy|firewall-policy| igmp-snoop-policy| management-policy|radius-server-policy|role-policy] use Associates the following policies with this profile: advanced-wips-policy <POLICY-NAME> Associates an advanced WIPS policy <POLICY-NAME> Specify the WIPS policy name.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 712 ParametersDevice mode use [advanced-wips-policy|auto-provisioning-policy|captive-portal| critical-resource-policy|dhcp-server-policy|event-system-policy|firewall-policy| igmp-snoop-policy|management-policy|profile|radius-server-policy|rf-domain| role-policy|wip-policy] auto-provisioning-policy <POLICY-NAME> Associates an auto provisioning policy <POLICY-NAME> Specify the auto provisioning policy name. captive-portal server <CAPTIVE-PORTAL> Configures access to a specified captive portal with this profile <CAPTIVE-PORTAL> Specify the captive portal name. critical-resource-policy <CRM-POLICY> Associates a critical resource policy <CRM-POLICY> Specify the critical resource policy name. dhcp-server-policy <DHCP-POLICY> Associates a DHCP server policy <DHCP-PLOICY> Specify the DHCP server policy name. event-system-policy <EVENT-SYSTEM-POLICY> Associates an event system policy <EVENT-SYSTEM-POLICY> Specify the event system policy name. firewall-policy <FW-POLICY> Associates a firewall policy <FW-POLICY> Specify the firewall policy name. igmp-snoop-policy <IGMP-POLICY> Associates an IGMP snoop policy <IGMP-POLICY> Specify the IGMP snoop policy name. management-policy <MNGT-POLICY> Associates a management policy <MNGT-POLICY> Specify the management policy name. radius-server-policy <RADIUS-POLICY> Associates a device onboard RADIUS policy <RADIUS-POLICY> Specify the RADIUS policy name. role-policy <ROLE-POLICY> Associates a role policy <ROLE-POLICY> Specify the role policy name. use Associates the following policies with this device: advanced-wips-policy <POLICY-NAME> Associates an advanced WIPS policy <POLICY-NAME> Specify the advanced WIPS policy name. auto-provisioning-policy <POLICY-NAME> Associates an auto provisioning policy <POLICY-NAME> Specify the auto provisioning policy name. captive-portal server <CAPTIVE-PORTAL> Configures access to a specified captive portal <CAPTIVE-PORTAL> Specify the captive portal name. critical-resource-policy <CRM-POLICY> Associates a critical resource policy <CRM-POLICY> Specify the critical resource policy name. dhcp-server-policy <DHCP-POLICY> Associates a DHCP server policy <DHCP-PLOICY> Specify the DHCP server policy name. event-system-policy <EVENT-SYSTEM-POLICY> Associates an event system policy <EVENT-SYSTEM-POLICY> Specify the event system policy name. firewall-policy <FW-POLICY> Associates a firewall policy <FW-POLICY> Specify the firewall policy name. igmp-snoop-policy <IGMP-POLICY> Associates an IGMP snoop policy <IGMP-POLICY> Specify the IGMP snoop policy name.
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 713 Example wm3400-34710C8(config-profile-default-WM3700)#use role-policy test wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-profile-default-WM3700)#use adoption-policy test wm3400-34710C8(config-profile-default-WM3700)# wm3400-34710C8(config-device-00-15-70-37-FA-BE)#use trustpoint trust1 https radius- ca-certificate radius-server-certificate wm3400-34710C8(config-device-00-15-70-37-FA-BE)# Related Commands management-policy <MNGT-POLICY> Associates a management policy <MNGT-POLICY> Specify the management policy name. profile <PROFILE-NAME> Associates a profile with this device <PROFILE-NAME> Specify the profile name. radius-server-policy <RADIUS-POLICY> Associates a device onboard RADIUS policy <RADIUS-POLICY> Specify the RADIUS policy name. rf-domain <RF-DOMAIN-NAME> Associates an RF Domain <RF-DOMAIN-NAME> Specify the RF Domain name. role-policy <ROLE-POLICY> Associates a role policy <ROLE-POLICY> Specify the role policy name. wips-policy <WIPS-POLICY> Associates a WIPS policy <WIPS-POLICY> Specify the WIPS policy name. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 714 vrrp Creating Profiles Configures Virtual Router Redundancy Protocol (VRRP) group settings Supported in the following platforms: AP4731 WM3400 WM3600 WM3700 Syntax vrrp [<1-255>|<version>] vrrp <1-255> [delta-priority|description|interface|ip|monitor|preempt|priority| sync-group|timers] vrrp <1-255> [delta-priority <1-253>|description <LINE>| interface [<VLAN-IF-NAME>|vlan <1-4094>]|ip <IP-ADDRESSES> {<IP-ADDRESSES>}| preempt {delay <1-65535>}|priority <1-254>|sync-group] vrrp <1-255> monitor [<IF-NAME>|criticial-resource action [decrement-priority| increment-priority]|pppoel|vlan <1-4094>|wwan1] {(<WORD>|critical- resource|pppoel| vlan|wwan1)} vrrp <1-255> timers advertise [<1-255>|centiseconds <25-4095>|msec <250-999>]] vrrp version [2|3] Parameters vrrp <1-255> [delta-priority <1-253>|description <LINE>| interface [<IF-NAME>|vlan <1-4094>]|ip <IP-ADDRESSES> {<IP-ADDRESSES>}| preempt {delay <1-65535>}|priority <1-254>|sync-group] vrrp <1-255> Configures the virtual router group ID from 1- 255. This field identifies the virtual router this packet is reporting status of. delta-priority <1-253> Configures the priority to decrement (local link monitoring and critical resource monitoring) or increment (critical resource monitoring). For monitor link, existing <1-253> Specify the delta priority level from 1- 253. description <LINE> Configures a text description for this VRRP group <LINE> Provide a description (a string from 1- 64 characters in length) interface [<VLAN-IF-NAME>| vlan <1-4094>] Enables VRRP on the Switch Virtual Interface (SVI) interface <VLAN-IF-NAME> Enables VRRP on the VLAN interface specified by the <VLAN-IF-NAME> parameter vlan <1-4094> Enables VRRP on the VLAN interface with ID specified by the <1 - 4094> parameter
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 715 vrrp <1-255> monitor [<IF-NAME>|criticial-resource action [decrement-priority| increment-priority]|pppoel|vlan <1-4094>|wwan1] {(<WORD>|critical- resource|pppoe1| vlan|wwan1)} vrrp <1-255> timers advertise [<1-255>|centiseconds <25-4095>|msec <250-999>] ip <IP-ADDRESSES> Enables and identifies the IP addresses) backed by the virtual router <P-ADDRESSES> Specify the IP addresses) in the A.B.C.D format. This configuration triggers VRRP operation and should be done at the end. preempt {delay <1-65535>} Controls whether a high priority backup router preempts a lower priority master. This field determines if a node with higher priority can takeover all virtual IPs from a node with lower priority. This feature is enabled by default delay Optional. Configures the pre-emption delay timer from 1 - 65535 seconds (default is 0 seconds). This option can be used to delay sending out the master advertisement or, in case of monitored link coming up, adjusting the VRRP priority by priority delta. priority <1-254> Configures the priority level of the router within a VRRP group. This value determines which node is elected as the Master. Higher values imply higher priority, value 254 has the highest precedence (default is 100). sync-group Adds this VRRP group to a synchronized group. For VRRP failover to be activated, it is essential that all individual groups within a synchronized group have failover. vrrp <1-255> Configures the virtual router ID from 1- 255. This field identifies the virtual router this packet is reporting status of. monitor Enables link or Critical Resource Monitoring (CRM) <IF-NAME> Enables interface monitoring <IF-NAME> Specify the interface name to monitor critical-resource action [decrement-priority| increment-priority] Enables critical resource monitoring action Sets the action on critical resource down event decrement-priority Decrements the priority of virtual router on critical resource down event increment-priority Increments the priority of virtual router on critical resource down event pppoel Enables Point-to-Point Protocol (PPP) over Ethernet interface monitoring vlan <1-4094> Enables VLAN (switched virtual interface) interface monitoring <1-4094> Specify the VLAN interface ID from 1- 4094. wwan1 Configures Wireless WAN interface monitoring vrrp <1-255> Configures the virtual router ID from 1- 255. This field identifies the virtual router this packet is reporting status of. timers Configures the timer that runs every interval
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 716 vrrp version [2|3] Usage Guidelines The node that wins the election enters the MASTER state and owns the virtual IP addresses. The Master node performs the following functions: Responds to ARP requests. Forwards packets with a destination link layer MAC address equal to the virtual router MAC address. Does not accept packets addressed to the IP address associated with the virtual router, if it is not the IP address owner. Accepts packets addressed to the IP address associated with the virtual router, if it is the IP address owner. The nodes that loose the election enter the BACKUP state and monitor the Master for any failures. In case of a failure one of the Backup router becomes the Master and takes over the virtual IPs. Example wm3400-34710C8(config-profile-default-wm3400)#vrrp version 3 wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#vrrp 1 sync-group wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#vrrp 1 delta-priority 100 wm3400-34710C8(config-profile-default-wm3400)# wm3400-34710C8(config-profile-default-wm3400)#show context profile wm3400 default-wm3400 bridge vlan 1 bridging-mode isolated-tunnel advertise [<1-255>| centiseconds <25-4095>| msec <250-999>] Configures the VRRP advertisements time interval. It is the interval at which a master sends out advertisements on each of its configured VLANs. <1-255> Configures the timer interval from 1- 255 seconds. (applicable for VRRP version 2 only) centiseconds <25-4095> Configures the timer interval in centiseconds (1/ 100th of a second). Specify a value between 25 - 4095 centiseconds (applicable for VRRP version 3 only) msec <250-999> Configures the timer interval in milliseconds (1/1000th of a second). Specify a value between 250 - 999 milliseconds (applicable for VRRP version 2 only) Default is 1 second vrrp version [2|3] Configures one of the following VRRP versions: 2 VRRP version 2 (RFC 3768) 3 VRRP version 3 (RFC 5798 only IPV4) Default is version 3
Creating Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 717 ip igmp snooping ip igmp snooping querier autoinstall configuration crypto ikev1 policy ikev1-default crypto ikev2 policy ikev2-default isakmp-proposal default encryption aes-256 group 2 hash sha crypto ipsec transform-set default esp-aes-256 esp-sha-hmac crypto ikev1 remote-vpn crypto ikev2 remote-vpn interface me1 interface ge1 ip dhcp trust qos trust dscp qos trust 802.1p interface ge2 ip dhcp trust qos trust dscp interface ge3 ip dhcp trust interface ge4 ip dhcp trust qos trust dscp qos trust 802.1p interface pppoe1 use firewall-policy default bridge nat source list BROADCAST-MULTICAST-CONTROL interface vlan1 overload service pm sys-restart router ospf ospf enable vrrp 1 priority 1 vrrp 1 timers advertise 1 vrrp 1 preempt vrrp 1 sync-group vrrp 1 delta-priority 100 vrrp version 3 wm3400-34710C8(config-profile-default-wm3400)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 718 wep-shared-key-auth Creating Profiles Enables support for 802.11 WEP shared key authentication Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wep-shared-key-auth Parameters None Example wm3400-34710C8(config-profile-default-WM3700)#wep-shared-key-auth wm3400-34710C8(config-profile-default-WM3700)# Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 719 Device Specific Commands Use the (config) instance to configure device specific parameters To navigate to this instance, use the following commands: wm3400-34710C8(config)#AP4731? wm3400-34710C8(config)#AP4731 00-15-70-88-9E-C4 wm3400-34710C8(config-device-00-15-70-88-9E-C4)#? Device Mode commands: aaa VPN AAA authentication settings ap-upgrade AP firmware upgrade area Set name of area where the system is located arp Address Resolution Protocol (ARP) auto-learn-staging-config Enable learning network configuration of the devices that come for adoption autoinstall Autoinstall Configuration commands bridge Ethernet bridge cdp Cisco Discovery Protocol channel-list Configure channel list to be advertised to wireless clients cluster Cluster configuration configuration-persistence Enable persistence of configuration across reloads (startup config file) contact Configure the contact controller WLAN controller configuration country-code Configure the country of operation crypto Encryption related commands dhcp-redundancy Enable DHCP redundancy dscp-mapping Configure IP DSCP to 802.1p priority mapping for untagged frames email-notification Email notification configuration enforce-version Check the firmware versions of devices before interoperating events System event messages floor Set name of a floor within a area where the system is located hostname Set system's network name interface Select an interface to configure ip Internet Protocol (IP) layout-coordinates Configure layout coordinates for this device led Turn LEDs on/off on the device legacy-auto-downgrade Enable device firmware to auto downgrade when other legacy devices are detected legacy-auto-update Auto upgrade of legacy devices license License management command lldp Link Layer Discovery Protocol load-balancing Configure load balancing parameter local Local user authentication database for VPN location Configure the location logging Modify message logging facilities mac-address-table MAC Address Table mac-name Configure MAC address to name mappings
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 720 mint MiNT protocol misconfiguration-recovery-time Check controller connectivity after configuration is received monitor Critical resource monitoring neighbor-inactivity-timeout Configure neighbor inactivity timeout neighbor-info-interval Configure neighbor information exchange interval no Negate a command or set its defaults noc Configure the noc related setting ntp Ntp server A.B.C.D override-wlan Configure RF Domain level overrides for wlan power-config Configure power mode preferred-controller-group Controller group this system will prefer for adoption radius Configure device-level radius authentication parameters remove-override Remove configuration item override from the device (so profile value takes effect) rf-domain-manager RF Domain Manager rsa-key Assign a RSA key to a service sensor-server AirDefense sensor server configuration spanning-tree Spanning tree stats Configure the stats related setting timezone Configure the timezone trustpoint Assign a trustpoint to a service use Set setting to use vpn Vpn configuration wep-shared-key-auth Enable support for 802.11 WEP shared key authentication clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-device-00-15-70-88-9E-C4)# The following table summarizes device mode commands Command Description Reference ap-upgrade Upgrades AP firmware page 8-546 arp Configures Address Resolution Protocol (ARP) parameters page 8-548 area Sets the name of area where the system is deployed page 8-723 arp Configures ARP parameters page 8-548
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 721 auto-learn-staging- config Enables the automatic recognition of devices pending adoption page 8-550 autoinstall Autoinstalls firmware image and configuration setup parameters autoinstall bridge commands Configures Ethernet Bridging parameters page 8-552 cdp Operates CDP on the device page 8-568 channel-list Configures channel list advertised to wireless clients page 8-724 cluster Sets cluster configuration page 8-570 configuration- persistence Enables configuration persistence across reloads page 8-573 contact Sets contact information page 8-725 controller Configures a WLAN wireless controller page 8-575 country-code Configures wireless controllers country code page 8-726 crypto Configures crypto settings page 8-579 dhcp-redundancy Enables DHCP redundancy page 8-727 dscp-mapping Configures IP Differentiated Services Code Point (DSCP) to 802.1p priority mapping for untagged frames page 8-613 email-notification Configures e-mail notification page 8-614 enforce-version Checks the device firmware version before attempting connection page 8-617 events Displays system event messages page 8-619 floor Sets the building floor where the system is deployed page 8-728 hostname Sets a system's network name page 8-729 interface Selects an interface to configure page 8-631 ip Configures IP components page 8-620 layout-coordinates Configures layout coordinates page 8-731 led Turns LEDs on or off page 8-669 legacy-auto- downgrade Enables legacy device firmware to auto downgrade page 8-670 legacy-auto-update Auto updates AP-4600 and AP4700 device firmware page 8-671 lldp Configures Link Layer Discovery Protocol (LLDP) settings for this profile page 8-672 load-balancing Configures load balancing parameters. page 8-674 location Configures the location the system is deployed page 8-733 logging Enables message logging page 8-679 mac-address-table Configures the MAC address table page 8-681 mac-name Configures MAC name to name mappings page 8-735 mint Configures MiNT protocol commands page 8-683 misconfiguration- recovery-time Verifies wireless controller connectivity after a configuration is received page 8-687 monitor Enables critical resource monitoring page 8-688 neighbor-inactivity- timeout Configures a neighbor inactivity timeout page 690 neighbor-info- interval Configures the neighbor information exchange interval page 8-737 no Negates a command or resets values to their default settings page 8-692 Command Description Reference
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 722 noc Configures NOC settings page 8-695 ntp Configure the NTP server settings page 8-696 override-wlan Configures WLAN RF Domain level overrides page 8-742 power-config Configures power mode features page 8-700 preferred-controller- group Specifies the wireless controller group the system prefers for adoption page 8-698 radius Configures device-level RADIUS authentication parameters page 8-702 remove-override Removes device overrides page 8-744 rf-domain-manager Enables the RF Domain manager page 8-705 rsa-key Assigns a RSA key to SSH page 8-746 sensor-server Configures an AirDefense sensor server page 8-748 spanning-tree Enables spanning tree commands page 8-706 stats Configures statistics settings page 8-750 timezone Configures wireless controller time zone settings page 8-752 trustpoint Assigns a trustpoint to a service page 8-753 use Defines the settings used with this command page 8-711 wep-shared-key- auth Enables support for 802.11 WEP shared key authentication page 8-718 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-390 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 723 area Device Specific Commands Sets the area where the system is deployed Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax area <AREA-NAME> Parameters area <AREA-NAME> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#area RMZEcoSpace wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname ap4700-889EC4 area RMZEcoSpace wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands area <AREA-NAME> Sets the area where the system is deployed no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 724 channel-list Device Specific Commands Configures the channel list advertised to wireless clients Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax channel-list [2.4GHz <CHANNEL-LIST>|5GHz <CHANNEL-LIST>|dynamic] Parameters channel-list [2.4GHz <CHANNEL-LIST>|5GHz <CHANNEL-LIST>|dynamic] Example Related Commands 2.4GHz <CHANNEL-LIST> Configures the channel list advertised by radios operating in the 2.4GHz mode <CHANNEL-LIST> Specify a list of channels separated by commas or hyphens. 5GHz <CHANNEL-LIST> Configures the channel list advertised by radios operating in the 5GHz mode <CHANNEL-LIST> Specify a list of channels separated by commas or hyphens. dynamic Enables dynamic update of channel list no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 725 contact Device Specific Commands Defines an administrative contact for a deployed device Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax contact <WORD> Parameters contact <WORD> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#contact symbol wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname ap4700-889EC4 area RMZEcoSpace contact symbol wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands contact <WORD> Specify the administrative contact name no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 726 country-code Device Specific Commands Sets the country of operation. Erases all existing radio configurations. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax country-code <WORD> Parameters country-code <COUNTRY-CODE> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#country-code us wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname ap4700-889EC4 area RMZEcoSpace contact symbol country-code us wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands country-code <COUNTRY-CODE> Configures the device to operate in a specified country <COUNTRY-CODE> Specify the two letter ISO-3166 country code. no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 727 dhcp-redundancy Device Specific Commands Enables DHCP redundancy Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-redundancy Parameters None Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname ap4700-889EC4 area RMZEcoSpace contact symbol country-code us dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)#
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 728 floor Device Specific Commands Sets the building floor where the device is deployed Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax floor <WORD> Parameters floor <FLOOR-NAME> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#floor 5floor wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname ap4700-889EC4 area RMZEcoSpace floor 5floor contact symbol country-code us dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands <FLOOR-NAME> Sets the building floor where the device is deployed no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 729 hostname Device Specific Commands Sets system's network name Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax hostname <WORD> Parameters hostname <WORD> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#hostname mywm3400 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# The hostname has changed from ap4700-889EC4 to mywm3400 wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor contact symbol country-code us dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)# hostname <WORD> Sets the name of the wireless controller. This name is displayed when the controller is accessed from any network.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 730 Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 731 layout-coordinates Device Specific Commands Configures X and Y layout coordinates for the device Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax layout-coordinates <-4096.0-4096.0> <-4096.0-4096.0> Parameters layout-coordinates <-4096.0-4096.0> <-4096.0-4096.0> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#layout-coordinates 1.5 2 wm3400-34710C8(config-device-00-15-70-88-9E-C4)#s wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 contact symbol country-code us dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)# <-4096.0-4096.0> Specify the X coordinate from -4096 - 4096.0 <-4096.0-4096.0> Specify the Y coordinate from -4096 - 4096.0
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 732 Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 733 location Device Specific Commands Configures the location where a wireless controller managed device is deployed Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax location <WORD> Parameters location <WORD> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#location Block3B wm3400-34710C8config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 location Block3B contact symbol country-code us dhcp-redundancy wm3400-34710C8(config-device-00-15-70-88-9E-C4)# <WORD> Configures the location where a wireless controller managed device is deployed
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 734 Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 735 mac-name Device Specific Commands Configures a MAC name for mappings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mac-name <MAC> <NAME> Parameters mac-name <MAC> <NAME> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#mac-name 00-15-70-88-9E-C4 TestDevice wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 location Block3B contact symbol country-code us dhcp-redundancy mac-name 00-15-70-88-9E-C4 TestDevice wm3400-34710C8(config-device-00-15-70-88-9E-C4)# <MAC> <NAME> Configures a MAC address for the device <NAME> Set the 'friendly' name used for this MAC address
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 736 Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 737 neighbor-info-interval Device Specific Commands Configures neighbor information exchange interval Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax neighbor-info-interval <1-100> Parameters neighbor-info-interval <1-100> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#neighbor-info-interval 50 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 location Block3B contact symbol country-code us dhcp-redundancy mac-name 00-15-70-88-9E-C4 TestDevice neighbor-info-interval 50 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# neighbor-info-interval <1-100> Sets neighbor information exchange interval <1-100> Specify a value from 1 - 100 seconds.
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 738 Related Commands no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 739 no Device Specific Commands Negates a command or resets values to their default Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [ap-upgrade|arp|auto-learn-staging-config|autoinstall| bridge|cdp|cluster|configuration-persistence|controller|crypto|dscp-mapping| email-notification|events|interface|ip|led|legacy-auto-downgrade| legacy-auto-update|lldp|load-balancing|logging|local|mac-address-table| mint|misconfiguration-recovery-time|monitor|noc|ntp|preferred-controller- group| radius|rf-domain-manager|spanning-tree|use|vpn|wep-shared-key-auth|service] Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated Example wm3400-34710C8(config-profile-default-WM3700)#no cluster wm3400-34710C8(config-profile-default-WM3700)# Related Commands ap-upgrade Upgrades AP firmware arp Configures Address Resolution Protocol (ARP) parameters area Sets the name of area where the system is deployed
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 740 arp Configures ARP parameters auto-learn-staging- config Enables the automatic recognition of devices pending adoption autoinstall Autoinstalls firmware image and configuration setup parameters bridge commands Configures Ethernet Bridging parameters cdp Operates CDP on the device channel-list Configures channel list advertised to wireless clients cluster Sets cluster configuration configuration- persistence Enables configuration persistence across reloads contact Sets contact information controller Configures a WLAN wireless controller country-code Configures wireless controllers country code crypto Configures crypto settings dhcp-redundancy Enables DHCP redundancy dscp-mapping Configures IP Differentiated Services Code Point (DSCP) to 802.1p priority mapping for untagged frames email-notification Configures e-mail notification enforce-version Checks the device firmware version before attempting connection events Displays system event messages floor Sets the building floor where the system is deployed hostname Sets a system's network name interface Selects an interface to configure ip Configures IP components layout-coordinates Configures layout coordinates led Turns LEDs on or off legacy-auto- downgrade Enables legacy device firmware to auto downgrade legacy-auto-update Auto updates AP-4600 and AP4700 legacy device firmware lldp Configures Link Layer Discovery Protocol (LLDP) settings for this profile load-balancing Configures load balancing parameters. location Configures the location the system is deployed logging Enables message logging mac-address-table Configures the MAC address table mac-name Configures MAC name to name mappings mint Configures MiNT protocol commands misconfiguration- recovery-time Verifies wireless controller connectivity after a configuration is received monitor Enables critical resource monitoring neighbor-inactivity- timeout Configures a neighbor inactivity timeout neighbor-info- interval Configures the neighbor information exchange interval no Negates a command or resets values to their default settings noc Configures NOC settings
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 741 ntp Configure the NTP server settings override-wlan Configures WLAN RF Domain level overrides power-config Configures power mode features preferred-controller- group Specifies the wireless controller group the system prefers for adoption radius Configures device-level RADIUS authentication parameters remove-override Removes device overrides rf-domain-manager Enables the RF Domain manager rsa-key Assigns a RSA key to SSH sensor-server Configures an AirDefense sensor server spanning-tree Enables spanning tree commands stats Configures statistics settings timezone Configures wireless controller time zone settings trustpoint Assigns a trustpoint to a service use Defines the settings used with this command wep-shared-key- auth Enables support for 802.11 WEP shared key authentication clrscr Clears the display screen commit Commits (saves) changes made in the current session do Runs commands from EXEC mode end Ends and exits the current mode and moves to the PRIV EXEC mode exit Ends the current mode and moves to the previous mode help Displays the interactive help system revert Reverts changes to their last saved configuration service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations show Displays running system information write Writes information to memory or terminal
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 742 override-wlan Device Specific Commands Configures WLAN RF Domain level overrides Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax override-wlan <WLAN> [ssid|vlan-pool|wpa-wpa2-psk] override-wlan <WLAN> [ssid <SSID>|vlan-pool <1-4094> {limit} <0-8192>| wpa-wpa2-psk <WORD>] Parameters override-wlan WLAN [ssid <SSID>|vlan-pool <1-4094> {limit <0-8192>}| wpa-wpa2-psk <WORD>] <WLAN> Specify the WLAN name. Configure the following WLAN parameters: SSID, VLAN pool, and WPA-WPA2 key. SSID <SSID> Configures the WLAN Service Set Identifier (SSID) <SSID> Specify an SSID ID. vlan-pool <1-4094> {limit <0-8192> Configures a pool of VLANs <1-4094> Specifies a VLAN ID from 1 - 4094. limit Optional. Limits the number of users on this VLAN pool <0-8192> Specify the user limit from 0 - 8192. wpa-wpa2-psk <WORD> Configures the WLAN WPA-WPA2 key or passphrase <WORD> Specify a WPA-WPA2 key or passphrase.
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 743 Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#override-wlan test vlan-pool 8 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#commit wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 location Block3B contact symbol country-code us dhcp-redundancy override-wlan test vlan-pool 8 limit 20 mac-name 00-15-70-88-9E-C4 TestDevice neighbor-info-interval 50 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 744 remove-override Device Specific Commands Removes device overrides Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax remove-override <parameters> Parameters None Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)*#remove-override ? aaa VPN AAA authentication settings all Remove all overrides for the device arp Address Resolution Protocol (ARP) auto-learn-staging-config Enable learning network configuration of the devices that come for adoption autoinstall Autoinstall Configuration commands bridge Bridge group commands cdp Cisco Discovery Protocol channel-list Configure a channel list to be advertised to wireless clients cluster Cluster configuration configuration-persistence Automatic write of startup configuration file contact The contact controller WLAN controller configuration controller-group Controller group this controller belongs to country-code The country of operation crypto Encryption related commands dhcp-redundancy DHCP redundancy dscp-mapping IP DSCP to 802.1p priority mapping for untagged frames
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 745 email-notification Email notification configuration enforce-version Check the firmware versions of devices before interoperating events System event messages firewall Enable/Disable firewall global Remove global overrides for the device but keeps per-interface overrides interface Select an interface to configure ip Internet Protocol (IP) lldp Link Layer Discovery Protocol local Local user authentication database for VPN location The location logging Modify message logging facilities mac-address-table MAC Address Table mint MiNT protocol noc Noc related configuration ntp Configure NTP override-wlan Overrides for wlans power-config Configure power mode rf-domain-manager RF Domain Manager sensor-server AirDefense WIPS sensor server configuration spanning-tree Spanning tree stats Stats-window related configuration timezone The timezone use Set setting to use vpn Vpn configuration service Service Commands wm3400-34710C8(config-device-00-15-70-88-9E-C4)*# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 746 rsa-key Device Specific Commands Assigns a RSA key to a device Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rsa-key ssh <RSA-KEY> Parameters rsa-key ssh <RSA-KEY> Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#rsa-key ssh rsa-key1 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 rsa-key ssh rsa-key1 location Block3B contact symbol country-code us dhcp-redundancy override-wlan test vlan-pool 8 limit 20 mac-name 00-15-70-88-9E-C4 TestDevice ssh <RSA-KEY> Assigns the RSA key to SSH <RSA-KEY> Specifies the RSA key name. The key should be installed using PKI commands in the enable mode
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 747 neighbor-info-interval 50 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 748 sensor-server Device Specific Commands Configures an AirDefense sensor server Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax sensor-server <1-3> ip <IP> {port [443|8443|<1-65535>}] Parameters sensor-server <1-3> ip <IP> {port [443|8443|<1-65535>} sensor-server <1-3> Selects a sensor server to configure ip <IP> Configures the IP address of the selected sensor server <IP> Specify the IP address. port [443|8443|<1-65535>] Optional. Configures the port. The options are: 443 The default port used by the AirDefense server 8443 The default port used by advanced WIPS on a wireless controller <1-65535> Manually sets the port number of the advanced WIPS/ AirDefense server
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 749 Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#sensor-server 3 ip 172.16.10.7 p ort 1080 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 hostname mywm3400 area RMZEcoSpace contact symbol country-code us dhcp-redundancy sensor-server 3 ip 172.16.10.7 port 1080 override-wlan test vlan-pool 8 limit 20 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 750 stats Device Specific Commands Configures statistics settings Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax stats open-window <1-2> {sample-interval <5-86640>} {size <3-100>} Parameters stats open-window <1-2> {sample-interval <5-86640>} {size <3-100>} Example wm3400-34710C8(config-device-00-15-70-88-9E-C4)#stats open-window 2 sample-inter val 77 size 10 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# wm3400-34710C8(config-device-00-15-70-88-9E-C4)#show context ap4700 00-15-70-88-9E-C4 use profile default-ap4700 use rf-domain default hostname mywm3400 area RMZEcoSpace floor 5floor layout-coordinates 1.5 2.0 rsa-key ssh rsa-key1 location Block3B contact symbol stats open-window 2 sample-interval 77 size 10 wm3400-34710C8(config-device-00-15-70-88-9E-C4)# open-window <1-2> Opens a stats window to fetch trending data. Set the index from 1 - 2. sample-interval <5-86640> Optional. Sets the sample interval from 5 - 86640 seconds size <3-100> Optional. Sets the stats window size and number of samples collected
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 751 Related Commands no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 752 timezone Device Specific Commands Configures wireless controllers timezone Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax timezone <TIMEZONE> Parameters timezone <TIMEZONE> Example wm3400-34710C8(config-device-00-15-70-37-FA-BE)#timezone india wm3400-34710C8(config-device-00-15-70-37-FA-BE)# Related Commands timezone <TIMEZONE> Configures the wireless controllers timezone no Disables or reverts settings to their default
Device Specific Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 753 trustpoint Device Specific Commands Assigns a trustpoint Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax trustpoint [https|radius-ca|radius-server] <TRUSTPOINT> Parameters trustpoint [https|radius-ca|radius-server] <TRUSTPOINT> Example wm3400-34710C8(config-device-00-15-70-37-FA-BE)#trustpoint radius-ca trust2 wm3400-34710C8(config-device-00-15-70-37-FA-BE)# Related Commands https <TRUSTPOINT> Assigns a specified trustpoint to HTTPS <TRUSTPOINT> Specify the trustpoint name. radius-ca <TRUSTPOINT> Uses EAP to assign a trustpoint as a certificate authority for validating client certificates <TRUSTPOINT> Specify the trustpoint name. radius-server <TRUSTPOINT> Specifies the name of the trustpoint. Install the trustpoint using PKI commands in the enable mode. <TRUSTPOINT> Specify the trustpoint name. no Disables or reverts settings to their default
Chapter 8: Profiles Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 754
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 755 C H A P T E R 9 AAA Policy This chapter summarizes the AAA policy commands within the CLI structure. Use the (config) instance to configure AAA policy commands. To navigate to the config-aaa-policy instance, use the following commands: wm3400-34710C8(config)#aaa-policy <POLICY-NAME> wm3400-34710C8(config)#aaa-policy test wm3400-34710C8(config-aaa-policy-test)#? AAA Policy Mode commands: accounting Configure accounting parameters authentication Configure authentication parameters health-check Configure server health-check parameters mac-address-format Configure the format in which the MAC address must be filled in the Radius-Request frames no Negate a command or set its defaults server-pooling-mode Configure the method of selecting a server from the pool of configured AAA servers use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-aaa-policy-test)#
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 756 aaa-policy The following table summarizes AAA policy commands accounting aaa-policy Configures the server type and interval at which interim accounting updates are sent to the server. Up to 6 accounting servers can be configured. Command Description Reference accounting Configures accounting parameters page 9-756 authentication Configures authentication parameters page 9-760 health-check Configures health check parameters page 9-764 mac-address-format Configures the MAC address format page 9-765 no Negates a command or sets its default page 9-767 server-pooling-mode Defines the method for selecting a server from the pool of configured AAA servers page 9-769 use Defines the AAA command settings page 9-770 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 757 Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accounting [interim|server|type] accounting interim interval <60-3600> accounting server [<1-6>|preference] accounting server preference [auth-server-host|auth-server-number|none accounting server <1-6> [dscp|host|nai-routing|onboard|proxy-mode| retry-timeout-factor|timeout] accounting server <1-6> [dscp <0-63>|retry-timeout-factor <50-200>] accounting server <1-6> host <HOSTNAME> secret [0 <SECRET>|2 <SECRET>|<SECRET>] {port <1-65535>} accounting server <1-6> nai-routing realm-type [prefix|suffix] realm <REALM-TEXT> {strip} accounting server <1-6> onboard [self|controller] accounting server <1-6> proxy-mode [none|through-controller| through-rf-domain-manager] accounting server <1-6> timeout <1-60> {attempts <1-10>} accounting type [start-interim-stop|start-stop|stop-only] Parameters accounting interim interval <60-3600> accounting server preference [auth-server-host|auth-server-number|none] interim Configures the interim accounting interval interval <60-3000> Specify the interim interval from 60 - 3600 seconds. server Configures an accounting server preference Configures the accounting server preference
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 758 accounting server <1-6> [dscp <0-63>|retry-timeout-factor <50-200>] accounting server <1-6> host <HOSTNAME> secret [0 <SECRET>|2 <SECRET>|<SECRET>] {port <1-65535>} accounting server <1-6> nai-routing realm-type [prefix|suffix] realm <REALM-TEXT> {strip} auth-server-host Sets the authentication server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its hostname. auth-server-number Sets the authentication server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its index or number. none Indicates the accounting server is independent of the authentication server server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured dscp <0-63> Sets the Differentiated Services Code Point (DSCP) value for Quality of Service (QOS) monitoring. This value is used in generated RADIUS packets. <0-63> Sets the DSCP value from 0 - 63 retry-timeout-factor <50-200> Sets the scaling factor for retry timeouts <50-200> Specify a value from 50 - 200. A value of 100 indicates the interval between 2 consecutive retries is the same irrespective of the number of retries. If the scaling factor value is less than 100, the time interval between two consecutive retires keeps reducing on subsequent retries. If this value is greater than 100, the time interval between two consecutive retries keeps increasing on subsequent retries. server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured host <HOSTNAME> Configures the accounting server hostname secret [0 <SECRET>| 2 <SECRET>|<SECRET>] Configures a common secret key used to authenticate with the accounting server 0 <SECRET> Configures a clear text secret key 2 <SECRET> Configures an encrypted secret key <SECRET> Specify the secret key. This shared secret should not exceed 127 characters. port <1-65535> Optional. Configures the accounting server port (the port used to connect to the accounting server) <1-65535> Sets the port number from 1 - 65535 server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured nai-routing Configures the Network Access Identifier (NAI) realm-type Selects the match type used on the username [prefix|suffix] Select one of the following options: prefix Matches the prefix of the username (For example, username is of type DOMAIN/user1, DOMAIN/user2) suffix Matches the suffix of the username (For example, user1@DOMAIN, user2)@DOMAIN)
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 759 accounting server <1-6> onboard [self|controller] accounting server <1-6> proxy-mode [none|through-controller| through-rf-domain-manager] accounting server <1-6> timeout <1-60> {attempts <1-10>} accounting type [start-interim-stop|start-stop|stop-only] Example wm3400-34710C8(config-aaa-policy-test)#accounting interim interval 65 wm3400-34710C8(config-aaa-policy-test)#accounting server 2 host 172.16.10.10 secret extreme port 1 wm3400-34710C8(config-aaa-policy-test)#accounting server 2 nai-routing realm-type prefix realm word strip realm Specifies the text matched against the username <REALM-TEXT> Specifies the matching text including the delimiter (a delimiter is typically '' or '@') strip Optional. Strips the realm from the username before forwarding the request to the RADIUS server server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured onboard Selects an onboard server instead of an external host self Configures the onboard server on a AP, or wireless controller, where the client is associated controller Configures the wireless controllers RADIUS server server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured proxy-mode Select the mode used to proxy requests. The options are: none, through- controller, and through-rf-domain-manager. none No proxy required. Sends the request directly using the IP address of the device through-controller Proxies requests through the wireless controller configuring the device through-rf-domain-manager Proxies requests through the local RF Domain manager server <1-6> Configures an accounting server. Up to 6 accounting servers can be configured timeout <1-60> Configures the timeout for each request sent to the RADIUS server <1-60> Specify a value from 1 - 60 seconds. {attempts<1-10>} Optional. Specified the number of times a transmission request is attempted <1-10> Specify a value from 1 - 10. type Configures the type of RADIUS accounting packets sent. The options are: start- interim-stop, start-stop, and stop-only. start-interim-stop Sends accounting-start and accounting-stop messages when the session starts and stops. This parameter also sends interim accounting updates. start-stop Sends accounting-start and accounting-stop messages when the session starts and stops stop-only Sends an accounting-stop message when the session ends
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 760 wm3400-34710C8(config-aaa-policy-test)#accounting server 2 host word secret word port 6000 wm3400-34710C8(config-aaa-policy-test)#accounting server 2 timeout 2 attempts 2 wm3400-34710C8(config-aaa-policy-test)#accounting type start-stop wm3400-34710C8(config-aaa-policy-test)#accounting server preference auth- server-number wm3400-34710C8(config-aaa-policy-test)#show context aaa-policy test accounting server 1 host 172.16.10.100 secret 0 testing accounting server 2 host 172.16.10.10 secret 0 extreme port 1008 accounting server 2 nai-routing realm-type prefix realm DSOS strip accounting type start-interim-stop accounting interim interval 65 accounting server preference auth-server-number Related Commands authentication aaa-policy Configures authentication parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication [eap|protocol|server] authentication eap wireless-client [attempts <1-10>|identity-request- timeout <1-60>| retry-timeout-factor <50-200>|timeout <1-60>] authentication protocol [chap|pap] no Resets values or disables commands
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 761 authentication server <1-6> [dscp|host|nac|nai-routing|onboard|proxy-mode| retry-timeout-factor|timeout] authentication server <1-6> dscp <0-63> authentication server <1-6> host <IP/HOSTNAME> secret [0 <SECRET>|2 <SECRET>| <SECRET>] {port <1-65535>} authentication server <1-6> nac authentication server <1-6> nai-routing realm-type [prefix|suffix] realm <REALMNAME> {strip} authentication server <1-6> onboard [controller|self] authentication server <1-6> proxy-mode [none|through-controller| through-rf-domain-manager] authentication server <1-6> retry-timeout-factor <50-200> authentication server <1-6> timeout <1-60> {attempts <1-10>} Parameters authentication eap wireless-client [attempts <1-10>|identity-request- timeout <1-60>|retry-timeout-factor <50-200>|timeout <1-60>] authentication protocol [chap|pap] authentication server <1-6> dscp <0-63> eap Configures Extensible Authentication Protocol (EAP) parameters wireless-client Configures wireless clients EAP parameters attempts <1-10> Configures the number of attempts to authenticate a wireless client <1-10> Specify a value from 1 - 10. identity-request-timeout <1-60> Configures the timeout interval after which an EAP identity request to a wireless client is resent <1-60> Specify a value from 1 - 60 seconds. retry-timeout-factor <50-200> Configures the spacing between successive EAP retries. A value of 100 indicates equal timeouts between retries. Smaller values indicate shorter timeouts, and larger values indicate longer timeouts between successive retries <50-200> Specify a value from 50 - 200. timeout <1-60> Configures the duration after which an EAP request to a wireless client is retried <1-60> Specify a value from 1 - 60 seconds. protocol [chap|pap] Configures the protocol used for non-EAP authentication chap Uses Challenge Handshake Authentication Protocol (CHAP) pap Uses Password Authentication Protocol (PAP) server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specify the RADIUS server index from 1 - 6. dscp <0-63> Configures the Differentiated Service Code Point (DSCP) quality of service parameter generated in RADIUS packets. The DSCP value specifies the class of service provided to a packet.
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 762 authentication server <1-6> host <IP/HOSTNAME> secret [0 <SECRET>| 2 <SECRET>|<SECRET>] {port <1-65535>} authentication server <1-6> nac accounting server <1-6> nai-routing realm-type [prefix|suffix] realm <REALMNAME> {strip} server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specify the RADIUS server index from 1 - 6. host <IP/HOSTNAME> Sets the RADIUS servers IP address or hostname secret [0 <SECRET>| 2 <SECRET>|<SECRET>] Configures the RADIUS server secret. This key is used to authenticate with the RADIUS server 0 <SECRET> Configures a clear text secret 2 <SECRET> Configures an encrypted secret <SECRET> Specify the secret key. The shared key should not exceed 127 characters. port <1-65535> Optional. Specifies the RADIUS server port (this port is used to connect to the RADIUS server) <1-65535> Specify a value from 1 - 65535. server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specifies the RADIUS server index from 1 - 6. nac Configures the RADIUS authentication server <1-6> used as a Network Access Control (NAC) server for devices requiring NAC server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specifies the RADIUS server index from 1 - 6. nai-routing Configures Network Access Identifier (NAI) RADIUS authentication realm-type [prefix|suffix] Configures the realm-type used for NAI authentication prefix Sets the realm prefix. For example, in the realm name AC\JohnTalbot, the prefix is AC and the user name JohnTalbot. suffix Sets the realm suffix. For example, in the realm name [email protected] the suffix is AC.org and the user name is JohnTalbot. realm <REALMNAME> Sets the realm information used for RADIUS authentication <REALMNAME> Sets the realm used for authentication. This value is matched against the user name provided for RADIUS authentication. Example: Prefix - AC\JohnTalbot Suffix - [email protected] strip Optional. Indicates the realm name must be stripped from the user name before sending it to the RADIUS server for authentication. For example, if the complete username is AC\JohnTalbot, then with the strip parameter enabled, only the JohnTalbot part of the complete username is sent for authentication.
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 763 authentication server <1-6> onboard [controller|self] authentication server <1-6> proxy-mode [none|through-controller|through-rf- domain-manager authentication server <1-6> retry-timeout-factor <50-200>] authentication server <1-6> timeout <1-60> {attempts <1-10>}] server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specify the RADIUS server index from 1 - 6. onboard [controller|self] Selects the onboard RADIUS server for authentication controller Indicates the RADIUS server is an onboard server self Indicates the RADIUS server is onboard server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Sets the RADIUS server index between 1 - 6 proxy-mode [none|through- controller|through-rf-domain- manager] Configures the mode for proxying a request none Proxying is not done. The packets are sent directly using the IP address of the device. through-controller Traffic is proxied through the wireless controller configuring this device through-rf-domain-manager Traffic is proxied through the local RF Domain manager server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specify the RADIUS server index from 1 - 6. retry-timeout-factor <50-200> Configures the scaling of timeouts between two consecutive RADIUS authentication retries <50-200> Specify the scaling factor from 50 - 200. A value of 100 indicates the time gap between two consecutive retires remains the same irrespective of the number of retries. A value lesser than 100 indicates the time gap between two consecutive retries reduces with each successive retry attempt. A value greater than 100 indicates the time gap between two consecutive retries increases with each successive retry attempt. server <1-6> Configures a RADIUS authentication server. Up to 6 RADIUS servers can be configured <1-6> Specify the RADIUS server index from 1 - 6. timeout <1-60> Configures the timeout, in seconds, for each request sent to the RADIUS server. This is the time allowed to elapse before another request is sent to the RADIUS server. If a response is received from the RADIUS server within this time, no retry is attempted. <1-60> Specify a value from 1 - 60 seconds. attempts <1-10> Optional. Indicates the number of retry attempts to make before giving up <1-10> Specify a value from 1 -10.
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 764 Example wm3400-34710C8(config-aaa-policy-test)#authentication server 5 host 172.16.10.10 secret extreme port 1009 wm3400-34710C8(config-aaa-policy-test)#authentication server 5 timeout 10 attempts 3 wm3400-34710C8(config-aaa-policy-test)#authentication server 5 nai-routing realm -type suffix realm @extremenetworks.com strip wm3400-34710C8(config-aaa-policy-test)#authentication protocol chap wm3400-34710C8(config-aaa-policy-test)#authentication eap wireless-client attempts 3 wm3400-34710C8(config-aaa-policy-test)#authentication eap wireless-client identity-request-timeout 20 wm3400-34710C8(config-aaa-policy-test)#authentication server 2 onboard controller wm3400-34710C8(config-aaa-policy-test)#show context aaa-policy test authentication server 5 onboard controller authentication server 5 timeout 20 authentication server 5 nai-routing realm-type suffix realm @extremenetworks.com strip accounting server 1 host 172.16.10.100 secret 0 testing accounting server 2 host 172.16.10.10 secret 0 extreme port 1008 accounting server 2 nai-routing realm-type prefix realm DSOS strip authentication eap wireless-client identity-request-timeout 20 authentication protocol chap accounting type start-interim-stop accounting interim interval 65 accounting server preference auth-server-number authentication server 5 host 172.16.10.10 secret 0 extreme port 1009 authentication server 5 timeout 20 authentication server 5 host 172 Related Commands health-check aaa-policy During normal operation, a AAA server can go offline. When a server goes offline, it is marked as down. This command configures the interval after which a server marked as down is checked to see if it has come back online and is reachable. no Resets values or disables commands
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 765 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax health-check interval <60-86400> Parameters interval <60-86400> Example wm3400-34710C8(config-aaa-policy-test)#health-check interval 4000 wm3400-34710C8(config-aaa-policy-test)# Related Commands mac-address-format aaa-policy Configures the format MAC addresses are filled in RADIUS request frames interval <60-86400> Configures an interval (in seconds) after which a server marked as down is checked to see if it is reachable again <60-86400> Specify a value from 60 - 86400 seconds. no Resets set values or disables commands
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 766 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mac-address-format [middle-hyphen|no-delim|pair-colon|pair-hyphen|quad-dot] case [lower|upper] attributes [all|username-password] Parameters] mac-address-format [middle-hyphen|no-delim|pair-colon|pair-hyphen|quad-dot] case [lower|upper] attributes [all|username-password] Example wm3400-34710C8(config-aaa-policy-test)#mac-address-format quad-dot case upper attributes username-password wm3400-34710C8(config-aaa-policy-test)#show context aaa-policy test mac-address-format quad-dot case upper attributes username-password middle-hyphen Configures the MAC address format as AABBCC-DDEEFF no-delim Configures the MAC address format as AABBCCDDEEFF pair-colon Configures the MAC address format as AA:BB:CC:DD:EE:FF quad-dot Configures the MAC address format as AABB.CCDD.EEFF case [lower|upper] Indicates the case the MAC address is formatted lower Indicates the MAC address is in lower case. For example, aa:bb:cc:dd:ee:ff upper Indicates the MAC address is in upper case. For example, AA:BB:CC:DD:EE:FF attributes [all|username- password] Configures RADIUS attributes to which this MAC format is applicable all Applies to all attributes with MAC addresses such as username, password, calling-station-id, and called-station-id username-password Applies only to the username and the password fields
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 767 Related Commands no aaa-policy Negates a AAA policy command or sets its default Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [accounting|authentication|health-check|mac-address-format|server- pooling-mode|use] no accounting interim interval no accounting server preference no accounting server <1-6> {dscp|nai-routing|proxy-mode|retry-timeout- factor|timeout} no accounting type no authentication eap wireless-client [attempts|identity-request- timeout|retry- timeout-factor|timeout] no authentication protocol no authentication server <1-6> {dscp|nac|nai-routing|proxy-mode|retry- timeout- factor|timeout} no health-check interval no mac-address-format no server-pooling-mode no use nac-list no Resets values or disables commands
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 768 Parameters no accounting interim interval no accounting server preference no accounting server <1-6> {dscp|nai-routing|proxy-mode|retry-timeout- factor|timeout} no accounting type no authentication eap wireless-client [attempts|identity-request- timeout|retry-timeout-factor|timeout] no authentication protocol no authentication server <1-6> {dscp|nai-routing|proxy-mode|retry-timeout- factor|timeout} no accounting interim interval Disables the periodic submission of accounting information no accounting server preference Resets the accounting server preference no accounting server <1-6> Resets the accounting server preference for the server specified by index <1-6> dscp Optional. Resets the DSCP value for RADIUS accounting nai-routing Optional. Disables Network Access Identifier (NAI) forwarding requests proxy-mode Optional. Resets proxy mode to the default value of no proxying retry-timeout-factor Optional. Resets retry timeout to its default of 100 timeout Optional. Resets access parameters, such as timeout values and retry attempts to their default no accounting type Resets the type of generated RADIUS accounting packets to its default no authentication eap wireless- client Resets Extensible Authentication Protocol (EAP) parameters for wireless clients attempts Resets the number of times a RADIUS request is sent to a wireless client identity-request-timeout Resets EAP identity request timeout to its default retry-timeout-factor Resets EAP retry timeout to its default of 100 timeout Resets EAP timeout to its default authentication protocol Resets the authentication protocol used for non-EAP authentication to its default (PAP authentication) no authentication server <1-6> Resets the accounting server preference for the server specified by index <1-6> dscp Optional. Resets the DSCP value for RADIUS authentication nai-routing Optional. Disables NAI forwarding requests proxy-mode Optional. Resets proxy mode to the default value of no proxying retry-timeout-factor Optional. Resets retry timeout to its default of 100
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 769 no health-check interval no mac-address-format no server-pooling-mode no use nac-list Example wm3400-34710C8(config-aaa-policy-test)#no accounting dscp wm3400-34710C8(config-aaa-policy-test)#no mac-address-format wm3400-34710C8(config-aaa-policy-test)#no server-pooling-mode fail-through wm3400-34710C8(config-aaa-policy-test)#no authentication server 3 proxy- mode wm3400-34710C8(config-aaa-policy-test)# Related Commands server-pooling-mode aaa-policy Configures the server selection method from a pool of AAA servers. The available methods are failover and load-balance. In the failover scenario, when a configured AAA server goes down, the server with the next higher index in the list of configured AAA server takes over for the failed server. timeout Optional. Resets all access parameters, such as timeout values and retry attempts to their default values no health-check interval Resets the server health check interval value to its default mac-address format Resets the MAC address format used in RADIUS request frames. The default of pair-hyphen is used. server-pooling-mode Resets the mode used to select an AAA server from a pool of configured servers use nac-list Detaches the current NAC list from being used in a AAA policy accounting Configures RADIUS accounting parameters authentication Configures RADIUS authentication parameters health-check Configures health check parameters mac-address-format Configures the MAC address format used in RADIUS packets server-pooling-mode Configures the RADIUS server pooling mode use Configures the use of NAC access lists
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 770 In the load-balance scenario, when a configured AAA server goes down, the remaining servers distribute the load amongst themselves. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax server-pooling-mode [failover|load-balance] Parameters server-pooling-mode [failover|load-balance] Example wm3400-34710C8(config-aaa-policy-test)#server-pooling-mode load-balance wm3400-34710C8(config-aaa-policy-test)#show context aaa-policy test server-pooling-mode load-balance Related Commands use aaa-policy Applies a Network Access Control (NAC) list for use by this AAA policy. This allows only the set of configured devices to use AAA servers. failover Sets the pooling mode to failover When a configured AAA server fails, the server with the next higher index takes over the AAA load. load-balance Sets the pooling mode to load balancing When a configured AAA server fails, all servers in the pool share the load of the failed server. no Resets values or disables commands
aaa-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 771 For more information on creating a NAC list, see Chapter 5, <$elemtextnac-list. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use nac-list <NAC-LIST> Parameters use nac-list <NAC-LIST> Example wm3400-34710C8(config-aaa-policy-test)#use nac-list test1 wm3400-34710C8(config-aaa-policy-test)#show context aaa-policy test server-pooling-mode load-balance use nac-list test1 Related Commands nac-list <NAC-LIST> Configures a NAC for use with the AAA policy <NAC-LIST> Specify the NAC list name. no Resets set values or disables commands nac-list Creates a NAC list
Chapter 9: AAA Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 772
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 773 C H A P T E R 10 Auto Provisioning Policy This chapter summarizes the auto provisioning policy commands in the CLI structure. Adoption rules are sorted by precedence value and matched (filtered) against the information available from an AP, any rule for the wrong AP type is ignored. For example, rule #1 adopt AP4731 10 profile default vlan 10 rule #2 adopt AP4600 20 profile default vlan 20 rule #3 adopt AP4731 30 profile default serial-number rule #4 adopt AP4731 40 p d mac aa bb AP4731 L2 adoption, VLAN 10 - will use rule #1 AP4731 L2 adoption, VLAN 20 - will not use rule #2 (wrong type), may use rule #3 if the serial number matched, else rule #4 If aa<= MAC <= bb, or else default. Use the (config) instance to configure auto-provisioning-policy commands. To navigate to the auto- provisioning-policy instance, use the following commands: wm3400-34710C8(config)#auto-provisioning-policy <POLICY-NAMe> wm3400-34710C8(config)#auto-provisioning-policy test1 wm3400-34710C8(config-auto-provisioning-policy-test)#? Auto-Provisioning Policy Mode commands: adopt Add rule for device adoption default-adoption Adopt devices even when no matching rules are found. Assign default profile and default rf-domain deny Add rule to deny device adoption no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes
Chapter 10: Auto Provisioning Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 774 service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-auto-provisioning-policy-test)# auto-provisioning-policy The following table summarizes auto provisioning policy commands adopt auto-provisioning-policy Adds device adoption rules Command Description Reference adopt Adds rules for device adoption page 10-774 default-adoption Adopts devices even when no matching rules are found. Assigns default profile and default RF Domain page 10-778 deny Adds a rule to deny device adoption page 10-778 no Negates a command or sets its default value page 10-781 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-382 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations service show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
auto-provisioning-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 775 Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [any|cdp-match|dhcp-option|fqdn|ip|lldp-match|mac|model- number| serial-number|vlan] ] adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> any adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [cdp-match <LOCATION-SUBSTRING>|dhcp-option <DHCP- OPTION>| fqdn <FQDN>|ip [<START-IP> <END-IP>|<IP/MASK>]|lldp-match <LLDP- STRING>| mac <START-MAC> {<END-MAC>}|model-number <MODEL-NUMBER>| serial-number <SERIAL-NUMBER>|vlan <VLAN> Parameters adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> any ap4021 Sets the AP adoption type as AP4021 ap4600 Sets the AP adoption type as AP4600 ap4511 Sets the AP adoption type as AP4511 ap4521 Sets the AP adoption type as AP4521 ap4532 Sets the AP adoption type as AP4532 ap4700 Sets the AP adoption type as AP4700 <1-1000> Sets the rule precedence. A rule with a lower value has a higher precedence in execution. <DEVICE-PROFILE> Sets the device profile for this provisioning policy. The selected device profile must be appropriate for the device being provisioned. For example, use an AP4600 device profile for an AP4600. Using an inappropriate device profile can result in unpredictable results.
Chapter 10: Auto Provisioning Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 776 adopt [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [cdp-match <LOCATION-SUBSTRING>|dhcp-option <DHCP-OPTION>| fqdn <FQDN>|ip [<START-IP> <END-IP>|<IP/MASK>]|lldp-match <LLDP-STRING>| mac <START-MAC> <END-MAC>|model-number <MODEL-NUMBER>| serial-number <SERIAL-NUMBER>|vlan <VLAN>] <RF-DOMAIN> Sets the RF Domain for this auto provisioning policy. The provisioning policy is only applicable to devices that try to become a part of the RF Domain any Indicates any device. Any device that meets the criteria defined is allowed to adopt to the wireless controller. ap4021 Sets the AP adoption type as AP4021 ap4600 Sets the AP adoption type as AP4600 ap4511 Sets the AP adoption type as AP4511 ap4521 Sets the AP adoption type as AP4521 ap4532 Sets the AP adoption type as AP4532 ap4700 Sets the AP adoption type as AP4700 <1-1000> Sets the rule precedence. A rule with a lower value has a higher precedence in execution. <DEVICE-PROFILE> Sets the device profile for this provisioning policy. The selected device profile must be appropriate for the device being provisioned. For example, use an AP4600 device profile for an AP4600. Using an inappropriate device profile can result in unpredictable results. <RF-DOMAIN> Sets the RF Domain for this auto provisioning policy. The provisioning policy is only applicable to devices that try to become a part of the RF Domain cdp-match <LOCATIO-SUBSTRING> Adopts any device based on the CISCO Discovery Protocol (CDP) snoop match <LOCATION-SUBSTRING> Specify the value to match. dhcp-option <DHCP-OPTION> DHCP options are used to identify the vendor and DHCP client functionalities. This information is used by the client to convey to the DHCP server that the client requires extra information in a DHCP response. This parameter allows a device to adopt based on its DHCP option. <DHCP-OPTION> Specify the DHCP option value to match. fqdn <FQDN> Fully Qualified Domain Name (FQDN) is a domain name that specifies its exact location in the DNS hierarchy. It specifies all domain levels, including its top-level domain and the root domain. This parameter allows a device to adopt based on its FQDN value. <FQDN> Specify the Fully Qualified Domain (FQDN) name to match. ip [<START-IP> <END-IP>| <IP/MASK>] Adopts a device if it matches the range of IP addresses, or is part of a subnet <START-IP> Specify the first IP address in the range. <END-IP> Specify the last IP address in the range. <IP/MASK> Specify the IP subnet and mask to match against the devices IP address. lldp-match <LLDP-STRING> Link Layer Discovery Protocol (LLDP) is a vendor neutral link layer protocol used to advertise a network devices identity, capabilities, and neighbors on a local area network. This parameter allows a device to adopt based on its LLDP information. <LLDP-STRING> Specify the LLDP information to match.
auto-provisioning-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 777 Example wm3400-34710C8(config-auto-provisioning-policy-test)#adopt AP4731 10 AP4731 default vlan 1 wm3400-34710C8(config-auto-provisioning-policy-test)#commit write memory wm3400-34710C8(config-auto-provisioning-policy-test)#show wireless ap +---+---------------+---------+-------------+--------------+ |IDX|NAME |MAC |TYPE|SERIAL-NUMBER |ADOPTION-MODE| VERSION | +---+---------------+---------+-------------+--------------+ | 1 | AP4731-889EC4 | 00-15-70-88-9E-C4 | AP4731 | 8164520900006 | L2: vlan1 | 5.3.0.0-033D | +---+---------------+-------------------+--------+---------------+-------- wm3400-34710C8(config-auto-provisioning-policy-test)#show wireless ap configured +-----+-----------------+---------------------+------------------+-------- | IDX | NAME | MAC | PROFILE | RF- DOMAIN | +-----+-----------------+---------------------+------------------+-------- | 1 | AP4731-889EC4 | 00-15-70-88-9E-C4 | default-AP4731 | default | | 2 | AP4600-445566 | 11-22-33-44-55-66 | default-AP4600 | default | +-----+-----------------+---------------------+------------------+-------- wm3400-34710C8(config-auto-provisioning-policy-test)#adopt AP4731 10 AP4731 default dhcp-option test wm3400-34710C8(config-auto-provisioning-policy-test)#adopt AP4731 10 AP4731 default ip 172.16.10.3 172.16.10.4 wm3400-34710C8(config-auto-provisioning-policy-test)#adopt AP4731 10 AP4731 default ip 172.16.10.3/24 wm3400-34710C8(config-auto-provisioning-policy-test)#adopt AP4731 10 AP4731 default mac 11-22-33-44-55-66 wm3400-34710C8(config-auto-provisioning-policy-test)#show context auto-provisioning-policy test adopt AP4731 10 AP4731 default vlan 1 wm3400-34710C8(config-auto-provisioning-policy-test)# mac <START-MAC> {<END-MAC>} Adopts a device if it matches the range of MAC addresses <START-MAC> Specify the first MAC address in the range. Provide this MAC address if you want to match for a single device. <END-MAC> Optional. Specify the last MAC address in the range. model-number <MODEL-NUMBER> Adopts a device if its model number matches <MODEL-NUMBER> <MODEL-NUMBER> Specify the model number to match. serial-number <SERIAL-NUMBER> Adopts a device if its serial number matches <SERIAL-NUMBER> <SERIAL-NUMBER> Specify the serial number to match. vlan <VLAN> Adopts a device if its VLAN matches <VLAN> <VLAN> Specify the VLAN to match.
Chapter 10: Auto Provisioning Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 778 Related Commands default-adoption auto-provisioning-policy Adopts devices, even when no matching rules are defined. Assigns a default profile and default RF Domain Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax default-adoption Parameters None Example wm3700-37FABE(config-auto-provisioning-policy-test)#default-adoption wm3700-37FABE(config-auto-provisioning-policy-test)#show context auto-provisioning-policy test default-adoption Related Commands deny auto-provisioning-policy Defines a deny device adoption rule no Resets values or disables commands no Resets values or disables commands
auto-provisioning-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 779 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [any|cdp-match|dhcp-option|fqdn|ip|lldp-match|mac|model- number| serial-number|vlan] ] deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> any deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [cdp-match <LOCATION-SUBSTRING>|dhcp-option <DHCP- OPTION>| fqdn <FQDN>|ip [<START-IP> <END-IP>|<IP/MASK>]|lldp-match <LLDP- STRING>| mac <START-MAC> {<END-MAC>}|model-number <MODEL-NUMBER>| serial-number <SERIAL-NUMBER>|vlan <VLAN>] Parameters deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> any ap4021 Sets the AP type as AP4021 ap4600 Sets the AP type as AP4600 ap4511 Sets the AP type as AP4511 ap4521 Sets the AP type as AP4521 ap4532 Sets the AP type as AP4532 ap4700 Sets the AP type as AP4700 <1-1000> Sets the rule precedence. A rule with a lower value has a higher precedence in execution. <DEVICE-PROFILE> Sets the device profile for this provisioning policy. The selected device profile must be appropriate for the device being provisioned. For example, use an AP4600 device profile for an AP4600. Using an inappropriate device profile can result in unpredictable results. <RF-DOMAIN> Sets the RF Domain for this auto provisioning policy. The provisioning policy is only applicable to devices that try to become a part of the RF Domain
Chapter 10: Auto Provisioning Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 780 deny [ap4021|ap4600|ap4511|ap4521|ap4532|ap4700] <1-1000> <DEVICE-PROFILE> <RF-DOMAIN> [cdp-match <LOCATION-SUBSTRING>|dhcp-option <DHCP-OPTION>| fqdn <FQDN>|ip [<START-IP> <END-IP>|<IP/MASK>]|lldp-match <LLDP-STRING>| mac <START-MAC> <END-MAC>|model-number <MODEL-NUMBER>| serial-number <SERIAL-NUMBER>|vlan <VLAN>] any Indicates any device. Any device that meets the criteria defined is not allowed to adopt to the wireless controller. ap4021 Sets the AP type as AP4021 ap4600 Sets the AP type as AP4600 ap4511 Sets the AP type as AP4511 ap4521 Sets the AP type as AP4521 ap4532 Sets the AP type as AP4532 ap4700 Sets the AP type as AP4700 <1-1000> Sets the rule precedence. A rule with a lower value has a higher precedence in execution. <DEVICE-PROFILE> Sets the device profile for this provisioning policy. The selected device profile must be appropriate for the device being provisioned. For example, use an AP4600 device profile for an AP4600. Using an inappropriate device profile can result in unpredictable results. <RF-DOMAIN> Sets the RF Domain for this auto provisioning policy. The provisioning policy is only applicable to devices that try to become a part of the RF Domain cdp-match <LOCATIO-SUBSTRING> Denies adoption to a device based on the CISCO Discovery Protocol (CDP) snoop match <LOCATION-SUBSTRING> Specify the value to match. dhcp-option <DHCP-OPTION> DHCP options identify the vendor and DHCP client functionalities. This information is used by the client to convey to the DHCP server that the client requires extra information in a DHCP response. This parameter denies adoption to a device based on its DHCP option. <DHCP-OPTION> Specify the DHCP option value. fqdn <FQDN> Fully Qualified Domain Name (FQDN) is a domain name that specifies its exact location in the DNS hierarchy. It specifies all domain levels, including its top-level domain and the root domain. This parameter denies adoption based on the fully qualified domain name of the device. <FQDN> Specify the FQDN to match. ip [<START-IP> <END-IP>| <IP/MASK>] Adopts a device if it matches the range of IP addresses or is part of a subnet <START-IP> Specify the first IP address in the range. <END-IP> Specify the last IP address in the range. <IP/MASK> Specify the IP subnet and mask to match against the devices IP address. lldp-match <LLDP-STRING> Link Layer Discovery Protocol (LLDP) is a vendor neutral link layer protocol that is used to advertise a network devices identity, capabilities, and neighbors on a local area network. This parameter denies adoption to a device based on its LLDP information. <LLDP-STRING> Specify the LLDP information to match. mac <START-MAC> {<END-MAC>} Adopts a device if it matches a single MAC address or a range of MAC addresses <START-MAC> Specify the first IP address in the range. Provide this MAC address if you want to match for a single device. <END-MAC> Optional. Specify the last IP address in the range.
auto-provisioning-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 781 Example wm3400-34710C8(config-auto-provisioning-policy-test)#deny AP4731 600 vlan 1 wm3400-34710C8(config-auto-provisioning-policy-test)#deny AP4731 600 ip 172.16.10.1/24 wm3400-34710C8(config-auto-provisioning-policy-test)#show context auto-provisioning-policy test default-adoption deny AP4700 100 vlan 20 deny AP4700 101 ip 172.16.11.0/24 Related Commands no auto-provisioning-policy Negates an auto provisioning policy command or sets its default Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [adopt|default-adoption|deny] no adopt <1-1000> no deny <1-1000> no default-adoption model-number <MODEL-NUMBER> Adopts a device if its model number matches <MODEL-NUMBER> <MODEL-NUMBER> Specify the model number to match. serial-number <SERIAL-NUMBER> Adopts a device if its serial number matches <SERIAL-NUMBER> <SERIAL-NUMBER> Specify the serial number to match. vlan <VLAN> Adopts a device if its VLAN matches <VLAN> <VLAN> Specify the VLAN to match. no Resets values or disables commands
Chapter 10: Auto Provisioning Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 782 Parameters no adopt <1-1000> no deny <1-1000> no default-adoption Example wm3700-37FABE(config-auto-provisioning-policy-test1)#no default-adoption wm3700-37FABE(config-auto-provisioning-policy-test1)# VS Related Commands Supported on the following platforms: Supported in the following platforms: adopt <1-1000> Removes an adoption rule from the list of rules based on its rule precedence <1-1000> Specify the rule precedence. deny <1-1000> Removes an adoption rule from the list of rules based on its rule precedence <1-1000> Specify the rule precedence. default-adoption Removes the default adoption rule. When the default adoption rule is absent, devices are not adopted adopt Configures an adoption rule default-adoption Configures the rule for adopting devices when adopt or deny rules are not defined deny Configures a deny adoption rule
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 783 C H A P T E R 11 Advanced WIPS Policy This chapter summarizes the advanced WIPS policy commands within the CLI structure. Use the (config) instance to configure advance WIPS policy commands. To navigate to the advanced WIPS policy instance, use the following commands: wm3400-34710C8(config)#advanced-wips-policy <POLICY-NAME> wm3400-34710C8(config)#advanced-wips-policy test wm3400-34710C8(config-advanced-wips-policy-test)#? Advanced WIPS policy Mode commands: event Configure event detection no Negate a command or set its defaults server-listen-port Configure local WIPS server listen port number terminate Add a device to the list of devices to be terminated use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3700-37FABE(config-advanced-wips-policy-test)# advanced-wips-policy The following table summarizes advanced WIPS policy commands Command Description Reference event Configures events page 11-784 no Negates a command or sets its default page 11-790
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 784 event advanced-wips-policy Configures the detection of anomalous frames in a RF network Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax event [accidental-association|all|crackable-wep-iv-used|dos-cts-flood| dos-deauthentication-detection|dos-disassociation-detection| dos-eap-failure-spoof|dos-eapol-logoff-storm|dos-rts-flood| essid-jack-attack-detected|fake-dhcp-server-detected|fata-jack-detected| id-theft-eapol-success-spoof-detected|id-theft-out-of-sequence| invalid-channel-advertized|invalid-management-frame|ipx-detection| monkey-jack-attack-detected|multicast-all-routers-on-subnet| multicast-all-systems-on-subnet| multicast-dhcp-server-relay-agent| multicast-hsrp-agent|multicast-igmp-detection|multicast-igrp-routers- server-listen- port Sets a local WIPS servers listening port page 11-793 terminate Adds a device to a list of terminated devices page 11-794 use Defines the settings used with the advanced WIPS policy page 11-795 clrscr Clears the display screen page 6-379 clrscr Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-379 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 785 detection| multicast-ospf-all-routers-detection|multicast-ospf-designated-routers- detection| multicast-rip2-routers-detection|multicast-vrrp-agent|netbios-detection| null-probe-response-detected|probe-response-flood|rogue-ap-detection| stp-detection|unauthorized-bridge|windows-zero-config-memory-leak| wlan-jack-attack-detected] event accidental-association mitigation-enable event accidental-association trigger-against sanctioned event all trigger-all-applicable event [crackable-wep-iv-used|dos-deauthentication-detection|dos- disassociation-detection|dos-eap-failure-spoof|essid-jack-attack- detected|fake-dhcp-server-dected|fata-jack-detected|id-theft-eapol-success- spoof-detected|id-theft-out-of-sequence|ipx-detection|monkey-jack-attack- detected|multicast-all-routers-on-subnet|multicast-all-systems-on- subnet|multicast-dhcp-server-relay-agent|multicast-hsrp-agent|multicast- igmp-detection|multicast-igrp-routers-detection|multicast-ospf-all-routers- detection|multicast-ospf-designated-routers-detection|multicast-rip2- routers-detection|multicast-vrrp-agent|netbios-detection|null-probe- response-detected|stp-detection|windows-zero-config-memory-leak|wlan-jack- attack-detected] trigger-against sanctioned event [dos-rts-flood|invalid-channel-advertized|invalid-management-frame] trigger-against (neighboring,sanctioned,unsanctioned) event dos-cts-flood threshold [cts-frames-ratio <0-65535>|mu-rx-cts-frame <0-65535> event dos-cts-flood trigger-against (neighboring,sanctioned,unsanctioned) event dos-eapol-logoff-storm threshold [eapol-start-frames-ap <0- 65535>|eapol-start-frames-mu <0-65535> event dos-eapol-logoff-storm trigger-against sanctioned event probe-response-flood threshold probe-rsp-frames-count <0-65535> event probe-response-flood trigger-against sanctioned event rogue-ap-detection mitigation-enable event rogue-ap-detection trigger-against (neighboring,sanctioned,unsanctioned) event unauthorized-bridge mitigation-enable event unauthorized-bridge trigger-against (neighboring,unsanctioned) Parameters event accidental-association mitigation-enable accidental-association This event occurs when a client accidentally associates to a wireless controller mitigation-enable Enables the default mitigation of an accidental association event
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 786 event accidental-association trigger-against sanctioned event all trigger-all-applicable event [crackable-wep-iv-used|dos-deauthentication-detection|dos- disassociation-detection|dos-eap-failure-spoof|essid-jack-attack- detected|fake-dhcp-server-dected|fata-jack-detected|id-theft-eapol-success- spoof-detected|id-theft-out-of-sequence|ipx-detection|monkey-jack-attack- detected|multicast-all-routers-on-subnet|multicast-all-systems-on- subnet|multicast-dhcp-server-relay-agent|multicast-hsrp-agent|multicast- igmp-detection|multicast-igrp-routers-detection|multicast-ospf-all-routers- detection|multicast-ospf-designated-routers-detection|multicast-rip2- routers-detection|multicast-vrrp-agent|netbios-detection|null-probe- response-detected|stp-detection|windows-zero-config-memory-leak|wlan-jack- attack-detected] trigger-against sanctioned accidental-association This event occurs when a client accidentally associates to a wireless controller trigger-against sanctioned Sets the trigger condition sanctioned The accidental association event is triggered against sanctioned devices all trigger-all-applicable Enables all events crackable-wep-iv-used This event occurs when a crackable WEP initialization vector is used The standard WEP64 uses a 40 bit key concatenated with a 24 bit initialization vector dos-deauthentication-detection This event occurs when a DoS Deauthentication attack is detected In this attack, clients connected to an AP are constantly forced to deauthenticate so they cannot stay connected to the network long enough to utilize it. dos-disassociation-detection This event occurs when a DoS disassociation attack is detected With this attack, clients connected to an AP are constantly disassociated. A fake deassociation frame is generated using an AP MAC address as the source address and the MAC address of the target device as the destination address. The target device on receiving this fake frame dissociates itself from the AP, then tries to re-associate. If the target receives a large number of deassociation frames, it will not be able to stay connected to the network long enough to utilize it. dos-eap-failure-spoof This event occurs when a Dos EAP failure spoofing attack is detected With this attack, the attacker generates a large number of EAP-failure packets forcing the AP to disassociate with its legitimate wireless clients. essid-jack-attack-detected This event occurs when an essid-jack attack is detected Essid-jack is a tool in the AirJack suite that sends a disassociate frame to a target client to force it to reassociate it to the network to find the SSID. This can be used to launch further DoS attacks on the network. fake-dhcp-server-detected This event occurs when a fake DHCP server is detected in the controlled network A fake or rogue DHCP server is a type of man in the middle attack where DHCP services are provide by an unauthorized DHCP server compromising the integrity of the wireless controller managed network.
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 787 fata-jack-detected This event occurs when a FATA-jack exploit is detected in the controller managed network FATA-jack is a tool in the AirJack suite that forces an AP to disassociate a valid client. This exploit uses a spoofed authentication frame with an invalid authentication algorithm number of 2. The attacker sends an invalid authentication frame with the wireless clients MAC, forcing the AP to return a deauth to the client. id-theft-eapol-success-spoof- detected This event occurs when an EAPOL success spoof is detected In this DoS attack, the attacker keeps the client from providing its credentials through the EAP-response packet by sending a EAP-success packet. Since the client is unable to provide its credentials, it cannot be authenticated and therefore cannot access the wireless network. id-theft-out-of-sequence This event occurs when an out of sequence packet is received This indicates a wireless client has been spoofed and is sending a packet out of sequence with the packet sent by the real wireless client. ipx-detection This event occurs when Novells Internetwork Packet Exchange (IPX) packets are detected monkey-jack-attack-detected This event occurs when a monkey-jack attack is detected Monkey-jack is a tool in the AirJack suite that enables an attacker to deauthenticate all wireless clients from an AP, and then insert itself between the AP and the wireless clients. multicast-all-routers-on-subnet This event occurs when a sanctioned device detects multicast packets to all routers on the subnet multicast-all-systems-on-subnet This event occurs when a sanctioned device detects multicast packets to all systems on the subnet multicast-dhcp-server-relay-agent This event occurs when a sanctioned device detects a DHCP server relay agent in the network multicast-hsrp-agent This event occurs when a sanctioned device detects a Hot Standby Router Protocol (HSRP) agent in the network multicast-igmp-detection This event occurs when a sanctioned device detects multicast Internet Group Management Protocol (IGMP) packets multicast-igrp-routers-detection This event occurs when a sanctioned device detects multicast Interior Gateway Routing Protocol (IGRP) packets multicast-ospf-all-routers- detection This event occurs when a sanctioned device detects multicast Open Shortest Path First (OSPF) packets multicast-ospf-designated- routers-detection This event occurs when a sanctioned device detects multicast OSPF routers in the network multicast-rip2-routers-detection This event occurs when a sanctioned device detects multicast Routing Information Protocol version 2 (RIP2) routers in the network multicast-vrrp-agent This event occurs when a sanctioned device detects multicast Virtual Router Redundancy Protocol (VRRP) agents in the network netbios-detection This event occurs when netbios packets are detected in the network Network Basic Input/Output System (netbios) provides services related to the sessions layer of the OSI model. This allows applications on different devices to communicate over the local area network. null-probe-response-detected This event occurs when a sanctioned device detects null probe response packets stp-detection This event occurs when a sanctioned device detects Scanning Tunnelling Protocol (STP) packets in the network windows-zero-config-memory- leak This event occurs when a Windows Zero-Config memory leak is detected
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 788 event [dos-rts-flood|invalid-channel-advertized|invalid-management-frame] trigger-against (neighboring,sanctioned,unsanctioned) event dos-cts-flood threshold [cts-frames-ratio <0-65535>|mu-rx-cts-frame <0-65535>] event dos-cts-flood trigger-against (neighboring,sanctioned,unsanctioned) wlan-jack-attack-detected This event occurs when a WLAN-jack exploit is detected in the wireless controller managed network. WLAN-jack is a tool in the AirJack suite that forces an AP to disassociate a valid client. The attacker sends deauthentication frames continuously or uses the broadcast address. This prevents the wireless clients from reassociating with the AP. trigger-against sanctioned Configures the event trigger condition sanctioned The selected event is only triggered against sanctioned devices dos-rts-flood This event occurs when a large number of request to send (RTS) frames are detected in the wireless controller managed network invalid-channel-advertized This event occurs when packets with invalid channels are detected in the wireless controller managed network invalid-management-frame This event occurs when an invalid management frame is detected in the controller managed network trigger-against (neighboring,sanctioned,unsancti oned) Sets the trigger condition. The following conditions are available: sanctioned An accidental association event is triggered against sanctioned devices unsanctioned An accidental association event is triggered against unsanctioned devices neighboring An accidental association event is triggered against neighboring devices dos-cts-flood This event occurs when a large number of clear to send (CTS) frames are detected in the network threshold [cts-frames-ratio <0- 65535>|mu-rx-cts-frame <0- 65535>] Sets the CTS flood threshold cts-frames-radio <0-65535> Sets the CTS:Total Frames ratio for triggering this event <0-65535> Specify the value from 0 - 65535. mu-rx-cts-frame Sets the CTS frame received by clients <0-65535> Specify the value from 0 - 65535. dos-cts-flood This event occurs when a large number of clear to send (CTS) frames are detected in the network trigger-against (neighboring,sanctioned,unsancti oned) Sets the trigger condition sanctioned An accidental association event is triggered against sanctioned devices unsanctioned An accidental association event is triggered against unsanctioned devices neighboring An accidental association event is triggered against neighboring devices
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 789 event dos-eapol-logoff-storm threshold [eapol-start-frames-ap <0- 65535>|eapol-start-frames-mu <0-65535> event dos-eapol-logoff-storm trigger-against sanctioned event probe-response-flood threshold probe-rsp-frames-count <0-65535> event probe-response-flood trigger-against sanctioned event rogue-ap-detection mitigation-enable event rogue-ap-detection trigger-against (neighboring,sanctioned,unsanctioned) dos-eapol-logoff-storm This event occurs when a large number of EAPOL logoff frames are detected in the network threshold [eapol-start-frames-ap <0-65535>|eapol-start-frames- mu <0-65535>] Sets the EAPOL logoff frames flood threshold eapol-start-frames-ap Sets the EAPOL start frames transmitted by an AP to trigger this event <0-65535> Specify a value from 0 - 65535. eapol-start-frames-mu Sets the EAPOL start frames transmitted by a client to trigger this event <0-65535> Specify a value from 0 - 65535. dos-eapol-logoff-storm This event occurs when a large number of EAPOL logoff frames are detected in the network trigger-against sanctioned Configures the event trigger condition sanctioned This event is triggered against sanctioned devices only probe-response-flood This event occurs when a large number of probe response frames are detected in the network threshold probe-rsp-frames-count <0-65535> Sets the probe response frames flood threshold probe-rsp-frames-count Sets the threshold from the number of probe response frames received <0-65535> Specify the value from 0 - 65535. probe-response-flood This event occurs when a large number of probe response frames are detected in the network trigger-against sanctioned Configures the event trigger condition. sanctioned This event is triggered against sanctioned devices only rogue-ap-detection This event occurs when rogue APs are detected in the network mitigation-enable Enables default mitigation for the rogue-ap-detection event rogue-ap-detection This event occurs when rogue APs are detected in the network.
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 790 event unauthorized-bridge mitigation-enable event unauthorized-bridge trigger-against (neighboring,unsanctioned) Example wm3700-37FABE(config-advanced-wips-policy-test)#event dos-cts-flood threshold cts-frames-ratio 8 wm3700-37FABE(config-advanced-wips-policy-test)#event dos-eapol-logoff- storm threshold eapol-start-frames-mu 99 wm3700-37FABE(config-advanced-wips-policy-test)#event probe-response-flood threshold probe-rsp-frames-count 8 wm3700-37FABE(config-advanced-wips-policy-test)#event wlan-jack-attack- detected trigger-against sanctioned wm3700-37FABE(config-advanced-wips-policy-test)#event probe-response-flood trigger-against sanctioned Related Commands no advanced-wips-policy Negates a command or sets its default value trigger-against (neighboring,sanctioned,unsanctio ned) Sets the trigger condition sanctioned An accidental association event is triggered against sanctioned devices unsanctioned An accidental association event is triggered against unsanctioned devices neighboring An accidental association event is triggered against neighboring devices unauthorized-bridge This event occurs when unauthorized bridges are detected in the network mitigation-enable Enables the default mitigation for the unauthorized-bridge event unauthorized-bridge This event occurs when unauthorized bridges are detected in the network trigger-against (neighboring,unsanctioned) Sets the trigger condition unsanctioned An accidental association event is triggered against unsanctioned devices neighboring An accidental association event is triggered against neighboring devices no Resets values or disables commands
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 791 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [event|server-listen-port|terminate|use] no event [accidental-association|crackable-wep-iv-used|dos-cts-flood| dos-deauthentication-detection|dos-disassociation-detection| dos-eap-failure-spoof|dos-eapol-logoff-storm|dos-rts-flood| essid-jack-attack-detected|fake-dhcp-server-detected|fata-jack-detected| id-theft-eapol-success-spoof-detected|id-theft-out-of-sequence| invalid-channel-advertized|invalid-management-frame|ipx-detection| monkey-jack-attack-detected|multicast-all-routers-on-subnet| multicast-all-systems-on-subnet| multicast-dhcp-server-relay-agent| multicast-hsrp-agent|multicast-igmp-detection|multicast-igrp-routers- detection| multicast-ospf-all-routers-detection|multicast-ospf-designated-routers- detection| multicast-rip2-routers-detection|multicast-vrrp-agent|netbios-detection| null-probe-response-detected|probe-response-flood|rogue-ap-detection| stp-detection|unauthorized-bridge|windows-zero-config-memory-leak| wlan-jack-attack-detected] no server-listen-port no terminate <MAC> no use device-configuration Parameters no event [accidental-association|crackable-wep-iv-used|dos-cts-flood| dos-deauthentication-detection|dos-disassociation-detection| dos-eap-failure-spoof|dos-eapol-logoff-storm|dos-rts-flood| essid-jack-attack-detected|fake-dhcp-server-detected|fata-jack-detected| id-theft-eapol-success-spoof-detected|id-theft-out-of-sequence| invalid-channel-advertized|invalid-management-frame|ipx-detection| monkey-jack-attack-detected|multicast-all-routers-on-subnet| multicast-all-systems-on-subnet| multicast-dhcp-server-relay-agent| multicast-hsrp-agent|multicast-igmp-detection|multicast-igrp-routers- detection|
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 792 multicast-ospf-all-routers-detection|multicast-ospf-designated-routers- detection| multicast-rip2-routers-detection|multicast-vrrp-agent|netbios-detection| null-probe-response-detected|probe-response-flood|rogue-ap-detection| stp-detection|unauthorized-bridge|windows-zero-config-memory-leak| wlan-jack-attack-detected] no server-listen-port no terminate <MAC> no use device-configuration event [accidental-association| crackable-wep-iv-used| dos-cts-flood| dos-deauthentication-detection| dos-disassociation-detection| dos-eap-failure-spoof| dos-eapol-logoff-storm| dos-rts-flood| essid-jack-attack-detected| fake-dhcp-server-detected| fata-jack-detected| id-theft-eapol-success-spoof-detected| id-theft-out-of-sequence| invalid-channel-advertized| invalid-management-frame| ipx-detection| monkey-jack-attack-detected| multicast-all-routers-on-subnet| multicast-all-systems-on-subnet| multicast-dhcp-server-relay-agent| multicast-hsrp-agent| multicast-igmp-detection| multicast-igrp-routers-detection| multicast-ospf-all-routers-detection| multicast-ospf-designated-routers-detection| multicast-rip2-routers-detection| multicast-vrrp-agent| netbios-detection| null-probe-response-detected| probe-response-flood| rogue-ap-detection| stp-detection| unauthorized-bridge| windows-zero-config-memory-leak| wlan-jack-attack-detected] Disables event handling for the event specified as its parameter See event for more information on each of the parameters. server-listen-port Resets the listen port for WIPS sensors to its default terminate <MAC> Removes a device by its MAC address <MAC> from the device termination list use device-categorization Removes the current device categorization list from the advanced WIPS policy
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 793 Example wm3400-34710C8(config-advanced-wips-policy-test)#no event accidental- association trigger-against wm3400-34710C8(config-advanced-wips-policy-test)#no server-listen-port wm3400-34710C8(config-advanced-wips-policy-test)#no use device- categorization wm3400-34710C8(config-advanced-wips-policy-test)#no terminate 11-22-33-44- 55-66 Related Commands server-listen-port advanced-wips-policy Defines the local WIPS servers listening port, where WIPS sensors connect to the local WIPS server Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax server-listen-port <0-65535> Parameters server-listen-port <0-65535> event Configures WIPS events server-listen-port Defines the port where WIPS sensors connect to the WIPS server terminate Adds a device to the device terminate list use Configures the device categorization list used with the advanced WIPS policy server-listen-port <0-65535> Select a port from 0 - 65535.
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 794 NOTE Onboard WIPS uses port 8443 and AirDefense Enterprise uses 443 Example wm3400-34710C8(config-advanced-wips-policy-test)#server-listen-port 1009 Related Commands terminate advanced-wips-policy Adds a device to a device termination list. Devices on this list cannot access the wireless controller managed network. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax terminate <MAC> Parameters terminate <MAC> Example wm3400-34710C8(config-advanced-wips-policy-test)#terminate 00-40-96-B0-BA- 2D no Resets values or disables commands terminate <MAC> Adds a device MAC address <MAC> to the device termination list. Devices on this list cannot access the wireless controller managed network
advanced-wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 795 Related Commands use advanced-wips-policy Uses an existing device categorization list with the advanced WIPS policy. A device configuration list must exist before it can be used with the advanced WIPS policy. A device categorization list categorizes a device, either an AP or a wireless client, as sanctioned or neighboring based on its MAC address or access point SSID. For more information on creating a device categorization list, see Chapter 5, <$elemtextdevice- categorization. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use device-categorization <DEVICE-CATEGORIZATION-LIST> Parameters NOTE advanced-wips ignores the SSID of marked devices for device-categorization Example wm3400-34710C8(config-advanced-wips-policy-test)#use device-categorization localdevices no Resets values or disables commands device-categorization <DEVICE-CATEGORIZATION- LIST> Configures device categorization list <DEVICE-CATEGORIZATION-LIST> Specify a device name to be associated to this profile.
Chapter 11: Advanced WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 796 Please note, advanced-wips ignores SSID of marked devices wm3400-34710C8(config-advanced-wips-policy-test)#show context advanced-wips-policy test use device-categorization localdevices wm3400-34710C8(config-advanced-wips-policy-test)# Related Commands no Resets values or disables command device-categorization Creates a device categorization list
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 797 C H A P T E R 12 Association ACL Policy This chapter summarizes the association ACL policy commands within the CLI structure. Use the (config) instance to configure association ACL policy related configuration commands. To navigate to the association-acl-policy instance, use the following commands: wm3400-34710C8(config)#association-acl-policy <POLICY-NAME> wm3400-34710C8(config)#association-acl-policy test wm3400-34710C8(config-assoc-acl-test)# wm3400-34710C8(config-assoc-acl-test)#? Association ACL Mode commands: deny Specify MAC addresses to be denied no Negate a command or set its defaults permit Specify MAC addresses to be permitted clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-assoc-acl-test)# association-acl-policy The following table summarizes association ACL policy commands Command Description Reference deny Specifies a range of denied MAC addresses page 12-798 no Negates a command or sets its default page 12-799
Chapter 12: Association ACL Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 798 deny association-acl-policy Identifies those devices denied access to the wireless controller managed network. Devices are identified by their MAC address. A single MAC address or a range of MAC addresses can be specified to deny access. This command also sets the precedence on how deny list rules are applied. Up to a thousand (1000) deny rules can be defined. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax deny <STARTING-MAC> [<ENDING-MAC>|precedence] deny <STARTING-MAC> precedence <1-1000> deny <STARING-MAC> <ENDING-MAC> precedence <1-1000> Parameters deny <STARTING-MAC> precedence <1-1000> permit Specifies a range of permitted MAC addresses page 12-801 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 deny Adds a single device or a set of devices to the deny list Command Description Reference
association-acl-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 799 deny <STARTING-MAC> <ENDING-MAC> precedence <1-1000> Example wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test wm3400-34710C8(config-assoc-acl-test)#deny 11-22-33-44-55-01 11-22-33-44- 55-FF precedence 150 wm3400-34710C8(config-assoc-acl-test)#deny 11-22-33-44-56-01 11-22-33-44- 56-01 precedence 160 wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 deny 11-22-33-44-56-01 11-22-33-44-56-01 precedence 160 wm3400-34710C8(config-assoc-acl-test)# Related Commands no association-acl-policy Negates a command or sets its default <STARTING-MAC> To add a single device, enter its MAC address in the <STARTING-MAC> parameter. precedence <1-1000> Sets a precedence rule. Rules are checked in an increasing order of precedence <1-1000> Specify a precedence value from 1 - 1000. deny Adds a single device or a set of devices to the deny list To add a set of devices, provide the range of MAC addresses. <STARTING-MAC> Specify the first MAC address in the range. <ENDING-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets a precedence rule. Rules are checked in an increasing order of precedence <1-1000> Specify a value from 1 - 1000. no Removes a device or a set of devices from the deny list
Chapter 12: Association ACL Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 800 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [deny|permit] no deny <STARTING-MAC> precedence <1-1000> no deny <STARING-MAC> <ENDING-MAC> precedence <1-1000> no permit <STARTING-MAC> precedence <1-1000> no permit <STARTING-MAC> <ENDING-MAC> precedence <1-1000> Parameters deny <STARTING-MAC> precedence <1-1000> deny <STARTING-MAC> <ENDING-MAC> precedence <1-1000> no permit <STARTING-MAC> precedence <1-1000> no deny Removes a single device or a set of devices from the deny list <STARTING-MAC> To remove a single device, enter its MAC address in the <STARTING-MAC> parameter. precedence <1-1000> Sets the rule precedence. Rules are checked in an increasing order of precedence value. <1-1000> Specify the value from 1 - 1000. no deny Removes a single device or a set of devices from the deny list To remove a set of devices, enter the range of MAC addresses. <STARTING-MAC> Specify the first MAC address in the range. <ENDING-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets the rule precedence. Rules are checked in an increasing order of precedence value. <1-1000> Specify a value from 1 - 1000. no permit Removes a single device or a set of devices from the permit list <STARTING-MAC> To remove a single device, enter its MAC address in the <STARTING-MAC> parameter.
association-acl-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 801 no permit <STARTING-MAC> <ENDING-MAC> precedence <1-1000> Example wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 deny 11-22-33-44-56-01 11-22-33-44-56-01 precedence 160 permit 11-22-33-44-66-01 11-22-33-44-66-FF precedence 170 permit 11-22-33-44-67-01 11-22-33-44-67-01 precedence 180 wm3400-34710C8(config-assoc-acl-test)#no deny 11-22-33-44-56-01 precedence 160 wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 permit 11-22-33-44-66-01 11-22-33-44-66-FF precedence 170 permit 11-22-33-44-67-01 11-22-33-44-67-01 precedence 180 wm3400-34710C8(config-assoc-acl-test)#no permit 11-22-33-44-67-01 11-22- 33-44-67-01 precedence 180 wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 permit 11-22-33-44-66-01 11-22-33-44-66-FF precedence 170 Related Commands permit association-acl-policy precedence <1-1000> Sets the rule precedence. Rules are checked in an increasing order of precedence value. <1-1000> Specify a value from 1 - 1000. no permit Removes a single device or a set of devices from the permit list To remove a set of devices, enter the range of MAC addresses. <STARTING-MAC> Specify the first MAC address in the range. <ENDING-MAC> Specify the last MAC address in the range. precedence <1-1000> Sets the rule precedence. Rules are checked in an increasing order of precedence value. <1-1000> Specify a value from 1 - 1000. deny Adds a device or a set of devices to the deny list permit Adds a device or a set of devices to the permit list
Chapter 12: Association ACL Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 802 Specifies devices permitted access to the wireless controller managed network. Devices are permitted access based on their MAC address. A single MAC address or a range of MAC addresses can be specified. This command also sets the precedence on how permit list rules are applied. Up to a thousand (1000) deny rules can be defined. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax permit <STARTING-MAC> [<ENDING-MAC>|precedence] permit <STARTING-MAC> precedence <1-1000> permit <STARING-MAC> <ENDING-MAC> precedence <1-1000> Parameters permit <STARTING-MAC> precedence <1-1000> permit <STARTING-MAC> <ENDING-MAC> precedence <1-1000> Example wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test permit Adds a single device or a set of devices to the permit list <STARTING-MAC> To add a single device, enter its MAC address in the <STARTING-MAC> parameter. precedence <1-1000> Sets a rule precedence. Rules are checked in an increasing order of precedence value <1-1000> Specify a value from 1 - 1000. permit Adds a single device or a set of devices to the permit list To add a set of devices, provide the range of MAC addresses. <STARTING-MAC> Specify the first MAC address of the range. <ENDING-MAC> Specify the last MAC address of the range. precedence <1-1000> Sets a rule precedence. Rules are checked in an increasing order of precedence value. <1-1000> Specify a value from 1 - 1000.
association-acl-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 803 deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 deny 11-22-33-44-56-01 11-22-33-44-56-01 precedence 160 wm3400-34710C8(config-assoc-acl-test)# wm3400-34710C8(config-assoc-acl-test)# permit 11-22-33-44-66-01 11-22-33- 44-66-FF precedence 170 wm3400-34710C8(config-assoc-acl-test)# permit 11-22-33-44-67-01 precedence 180 wm3400-34710C8(config-assoc-acl-test)#show context association-acl-policy test deny 11-22-33-44-55-01 11-22-33-44-55-FF precedence 150 deny 11-22-33-44-56-01 11-22-33-44-56-01 precedence 160 permit 11-22-33-44-66-01 11-22-33-44-66-FF precedence 170 permit 11-22-33-44-67-01 11-22-33-44-67-01 precedence 180 Related Commands no Removes a device or a set of devices from the permit list
Chapter 12: Association ACL Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 804
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 805 C H A P T E R 13 Access List This chapter summarizes IP and MAC access list commands in detail. Access lists control access to the network using a set of rules. Each rule specifies an action taken when a packet matches a given set of rules. If the action is deny, the packet is dropped. If the action is permit, the packet is allowed. The controller supports the following ACLs: IP access lists MAC access lists Use IP and MAC commands under the global configuration to create an access list. When the access list is applied on an Ethernet port, it becomes a port ACL When the access list is applied on a VLAN interface, it becomes a router ACL Use the (config) instance to configure access list commands. To navigate to the (config-access-list) instance, use the following commands: ip-access-list wm3400-34710C8(config)#ip access-list test wm3400-34710C8(config-ip-acl-acl)#? ACL Config commands: deny Specify packets to reject no Negate a command or set its defaults permit Specify packets to forward clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-ip-acl-acl)# mac-access-list
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 806 wm3400-34710C8(config)#mac access-list test wm3400-34710C8(config-mac-acl-test)#? MAC Extended ACL Config commands: deny Specify packets to reject no Negate a command or set its defaults permit Specify packets to forward clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-mac-acl-test)# ip-access-list Access List The following table summarizes commands under the IP access list mode deny ip-access-list Specifies packets to reject Command Description Reference deny Specifies packets to reject page 13-806 no Negates a command or sets its default page 13-811 permit Permits specific packets page 13-817 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 807 NOTE Use a decimal value representation to implement a permit/deny designation for a packet. The command set for IP ACLs provides the hexadecimal values for each listed EtherType. The wireless controller supports all EtherTypes. Use the decimal equivalent of the EtherType listed for any other EtherType. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax deny [icmp|ip|proto|tcp|udp] deny ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} deny icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>| any|host <IP>] <ICMP-TYPE> <ICMP-CODE> [log rule-precedence <1- 5000>| rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} deny proto [<PROTOCOL-NUMBER>|<PROTOCOL-NAME>|eigrp|gre|igmp|igp|ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>}] deny [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE-PORT>|range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>}]
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 808 Parameters deny icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>| any|host <IP>] <ICMP-TYPE> <ICMP-CODE> [log rule-precedence <1-5000>| rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} deny ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} icmp Configures the ACL for Internet Control Message Protocol (ICMP) packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to deny access any Identifies all devices as the source to deny access host <IP> Identifies a specific host as the source to deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny access any Identifies all devices as the destination to deny access host <IP> Identifies a specific host as the destination to deny access <IP> Specify the host IP address. <ICMP-TYPE> Defines the ICMP packet type For example, an ICMP type 0 indicates it is an ECHO REPLY, and type 8 indicates it is an ECHO. <ICMP-CODE> Defines the ICMP message type For example, an ICMP code 3 indicates Destination Unreachable, code 1 indicates Host Unreachable, and code 3 indicates Port Unreachable. log Logs all deny events rule-precedence <1-5000> Sets the rule precedence. Rules are checked in an increasing order of precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Defines the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. ip Configures the ACL for IP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to deny access any Identifies all devices as the source to deny access host <IP> Identifies a specific host as the source to deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny access any Identifies all devices as the destination to deny access host <IP> Identifies a specific host as the destination to deny access <IP> Specify the host IP address. log Logs all deny events rule-precedence <1-5000> Sets the rule precedence. Rules are checked in an increasing order of precedence <1-5000> Specify the rule precedence from 1 - 5000.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 809 deny proto [<PROTOCOL-NUMBER>|<PROTOCOL-NAME>|eigrp|gre|igmp|igp|ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} deny [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE-PORT>| range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} rule-description <RULE-DESCRIPTION> Optional. Defines the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. proto Configures the ACL for additional protocols Additional protocols (other than IP, ICMP, TCP, and UDP) must be configured using this parameter <PROTOCOL-NUMBER> Filters protocols using their Internet Assigned Numbers Authority (IANA) protocol number <PROTOCOL-NAME> Filters protocols using their IANA protocol name eigrp Identifies the Enhanced Internet Gateway Routing Protocol (EIGRP) protocol gre Identifies the General Routing Encapsulation (GRE) protocol igmp Identifies the Internet Group Management Protocol (IGMP) protocol igp Identifies any private internal gateway (primarily used by CISCO for their IGRP) ospf Identifies the Open Shortest Path First (OSPF) protocol vrrp Identifies the Virtual Router Redundancy Protocol (VRRP) protocol <SOURCE-IP/MASK> Sets the IP address and mask as the source to deny access any Identifies all devices as the source to deny access host <IP> Identifies a specific host as the source to deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny access any Identifies all devices as the destination to deny access host <IP> Identifies a specific host as the destination to deny access <IP> Specify the host IP address. log Logs all deny events rule-precedence <1-5000> Sets the rule precedence. Rules are checked in an increasing order of precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. tcp Configures the ACL for TCP packets udp Configures the ACL for UDP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to deny access
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 810 Usage Guidelines Use this command to deny traffic between networks/hosts based on the protocol type selected in the access list configuration. The following protocols are supported: any Identifies all devices as the source to deny access host <IP> Identifies a specific host as the source to deny access <IP> Specify the host IP address. eq <SOURCE-PORT> Identifies a specific source port <SOURCE-PORT> Specify the source port. range <START-PORT> <END-PORT> Specifies the source port range <START-PORT> Specify the start in the port range. <END-PORT> Specify the end in the port range. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny access any Identifies all devices as the destination to deny access host <IP> Identifies a specific host as the destination to deny access <IP> Specify the host IP address. eq [<DESTINATION-PORT> |bgp|dns|ftp|ftp-data|gopher| https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www] Identifies a specific destination or protocol port <DESTINATION-PORT> The destination port designated by its number bgp The designated BGP protocol port dns The designated DNS protocol port ftp The designated FTP protocol port ftp-data The designated FTP data port gropher The designated GROPHER protocol port https The designated HTTPS protocol port ldap The designated LDAP protocol port nntp The designated NNTP protocol port ntp The designated NTP protocol port pop3 The designated POP3 protocol port smtp The designated SMTP protocol port ssh The designated SSH protocol port telnet The designated Telnet protocol port tftp The designated TFTP protocol port www The designated www protocol port range <START-PORT> <END-PORT> Specifies the destination port range <START-PORT> Specify the start in the port range. <END-PORT> Specify the end in the port range. log Logs all deny events rule-precedence <1-5000> Sets the rule precedence. Rules are checked in an increasing order of precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 811 ip icmp tcp udp proto The last ACE in the access list is an implicit deny statement. Whenever the interface receives the packet, its content is checked against the ACEs in the ACL. It is allowed/denied based on the ACL configuration. Filtering TCP/UDP allows the user to specify port numbers as filtering criteria Select ICMP as the protocol to allow/deny ICMP packets. Selecting ICMP provides the option of filtering ICMP packets based on ICMP type and code NOTE The log option is functional only for router ACLs. The log option displays an informational logging message about the packet that matches the entry sent to the console. Example wm3400-34710C8(config-ip-acl-test)#show context ip access-list test wm3400-34710C8(config-ip-acl-test)#deny proto vrrp any any log rule- precedence 600 wm3400-34710C8(config-ip-acl-test)#deny proto ospf any any log rule- precedence 650 wm3400-34710C8(config-ip-acl-test)#show context ip access-list test deny proto vrrp any any log rule-precedence 600 deny proto ospf any any log rule-precedence 650 Related Commands no ip-access-list Negates a command or sets its default no Resets values or disables IP access deny command
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 812 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [deny|permit] no [deny|permit] [icmp|ip|prpto|tcp|udp] no [deny|permit] icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any| host <IP>] <ICMP-TYPE> <ICMP-CODE> (log,mark [8021p <0-7>|dscp <0- 63>], rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} no [deny|permit] ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any| host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1- 5000>) {rule-description <RULE-DESCRIPTION>} no [deny|permit] proto [<PROTOCOL-NUMBER>|<PROTOCOL- NAME>|eigrp|gre|igmp|igp| ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any|host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} no [deny|permit] [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE- PORT>| range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} Parameters no [deny|permit] icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 813 any|host <IP>] <ICMP-TYPE> <ICMP-CODE> (log,mark [8021p <0-7>|dscp <0-63>], rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} no [deny|permit] ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any| host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} no deny Removes a deny rule no permit Removes a permit rule icmp Removes the ACL for ICMP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit/deny access any Identifies all devices as the source to permit/deny access host <IP> Identifies a specific host as the source to permit/deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit/deny access any Identifies all devices as the destination to permit/deny access host <IP> Identifies a specific host as the destination to permit/deny access <IP> Specify the host IP address. <ICMP-TYPE> Defines the ICMP packet type For example, an ICMP type 0 indicates it is an ECHO REPLY, and type 8 indicates it is an ECHO <ICMP-CODE> Defines the ICMP message type For example, an ICMP code 3 indicates Destination Unreachable, code 1 indicates Host Unreachable, and code 3 indicates Port Unreachable. log Logs all permit/deny events mark [8021p <0-7>|dscp <0-63> Marks each packet that matches the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. no deny Removes a deny rule no permit Removes a permit rule ip Removes the ACL for IP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit/deny access any Identifies all devices as the source to permit/deny access host <IP> Identifies a specific host as the source to permit/deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit/deny access any Identifies all devices as the destination to permit/deny access host <IP> Identifies a specific host as the destination to permit/deny access <IP> Specify the host IP address.
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 814 no [deny|permit] proto [<PROTOCOL-NUMBER>|<PROTOCOL- NAME>|eigrp|gre|igmp|igp| ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any| host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1- 5000>) {rule-description <RULE-DESCRIPTION>} log Logs all permit/deny events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. no deny Removes a deny rule no permit Removes a permit rule proto Removes ACLs for additional protocols Additional protocols (other than IP, ICMP, TCP, and UDP) must be removed using this parameter <PROTOCOL-NUMBER> Identifies an IANA protocol number <PROTOCOL-NAME> Identifies an IANA protocol name eigrp Identifies the EIGRP protocol gre Identifies the GRE protocol igmp Identifies the IGMP protocol igp Identifies any private internal gateway (primarily used by CISCO for their IGRP) ospf Identifies the OSPF protocol vrrp Identifies the VRRP protocol <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit/deny access any Identifies all devices as the source to permit/deny access host <IP> Identifies a specific host as the source to permit/deny access <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit/deny access any Identifies all devices as the destination to permit/deny access host <IP> Identifies a specific host as the destination to permit/deny access <IP> Specify the host IP address. log Logs all permit/deny events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 815 no [deny|permit] [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE- PORT>| range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. no deny Removes a deny rule no permit Removes a permit rule tcp Removes the ACL for TCP packets udp Removes the ACL for UDP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit/deny access any Identifies all devices as the source to permit/deny access host <IP> Identifies a specific host as the source to permit/deny access <IP> Specify the host IP address eq <SOURCE-PORT> Identifies a specific source port <SOURCE-PORT> Specify the source port range <START-PORT> <END-PORT> Identifies the source port range <START-PORT> Specify the start of the range. <END-PORT> Specify the end of the range. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit/deny access any Identifies all devices as the destination to permit/deny access host <IP> Identifies a specific host as the destination to permit/deny access <IP> Specify the host IP address.
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 816 Usage Guidelines Removes an access list control entry. Provide the rule-precedence value when using the no command. Example wm3400-34710C8(config-ip-acl-test)#show context ip access-list test deny proto vrrp any any log rule-precedence 600 deny proto ospf any any log rule-precedence 650 permit ip 172.16.10.0/24 any log rule-precedence 750 permit tcp 172.16.10.0/24 any log rule-precedence 800 wm3400-34710C8(config-ip-acl-test)#no permit ip 172.16.10.0/24 any log rule-precedence 750 wm3400-34710C8(config-ip-acl-test)#show context ip access-list test deny proto vrrp any any log rule-precedence 600 deny proto ospf any any log rule-precedence 650 eq [<DESTINATION-PORT> |bgp|dns|ftp|ftp-data|gopher| https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www] Identifies a specific destination or protocol port <DESTINATION-PORT> The destination port designated by its number bgp The designated BGP protocol port dns The designated DNS protocol port ftp The designated FTP protocol port ftp-data The designated FTP data port gropher The designated GROPHER protocol port https The designated HTTPS protocol port ldap The designated LDAP protocol port nntp The designated NNTP protocol port ntp The designated NTP protocol port pop3 The designated POP3 protocol port smtp The designated SMTP protocol port ssh The designated SSH protocol port telnet The designated Telnet protocol port tftp The designated TFTP protocol port www The designated www protocol port range <START-PORT> <END-PORT> Identifies the destination port range <START-PORT> Specify the start of the range. <END-PORT> Specify the end of the range. log Logs all permit/deny events rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 817 permit tcp 172.16.10.0/24 any log rule-precedence 800 Related Commands permit ip-access-list Permits specific packets NOTE Use a decimal value representation to implement a permit/deny designation for a packet. The command set for IP ACLs provide the hexadecimal values for each listed EtherType. The controller supports all EtherTypes. Use the decimal equivalent of the EtherType listed for any other EtherType. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax permit [icmp|ip|proto|tcp|udp permit icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/ MASK>|any|host <IP>] <ICMP-TYPE> <ICMP-CODE> (log,mark [8021p <0-7>|dscp <0-63>], rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} permit ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} permit proto [<PROTOCOL-NUMBER>|<PROTOCOL- NAME>|eigrp|gre|igmp|igp|ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host deny Creates a deny ACL permit Creates a permit ACL
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 818 <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} permit [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE-PORT>| range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] [log rule-precedence <1-5000>|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} Parameters permit icmp [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any| host <IP>] <ICMP-TYPE> <ICMP-CODE> (log,mark [8021p <0-7>|dscp <0-63>], rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} permit ip [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] icmp Configures an ACL for ICMP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit access any Permits traffic from all potential sources host <IP> Permits traffic from a specific host <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit access any Permits traffic to all destinations host <IP> Permits traffic to a specific host <IP> Specify the host IP address. <ICMP-TYPE> Defines the ICMP packet type For example, an ICMP type 0 indicates it is an ECHO REPLY, and type 8 indicates it is an ECHO <ICMP-CODE> Defines the ICMP message type For example, an ICMP code 3 indicates Destination Unreachable, code 1 indicates Host Unreachable, and code 3 indicates Port Unreachable. log Logs all permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 819 (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} permit proto [<PROTOCOL-NUMBER>|<PROTOCOL- NAME>|eigrp|gre|igmp|igp|ospf|vrrp] [<SOURCE-IP/MASK>|any|host <IP>] [<DESTINATION-IP/MASK>|any|host <IP>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} ip Configures an ACL for IP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit access any Permits traffic from all potential sources host <IP> Permits traffic from a specific host <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit access any Permits traffic to all destinations host <IP> Permits traffic to a specific host <IP> Specify the host IP address. log Logs all permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. proto Configures an ACL for additional protocols Other protocols (other than IP, ICMP, TCP, and UDP) must be configured using this parameter. <PROTOCOL-NUMBER> Filters protocols using their IANA protocol number <PROTOCOL-NAME> Filters protocols using their IANA protocol name eigrp Identifies the EIGRP protocol gre Identifies the GRE protocol igmp Identifies the IGMP protocol igp Identifies any private internal gateway (primarily used by CISCO for their IGRP) ospf Identifies the OSPF protocol vrrp Identifies the VRRP protocol <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit access any Permits traffic from all potential sources host <IP> Permits traffic from a specific host <IP> Specify the host IP address. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit access any Permits traffic to all destinations
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 820 permit [tcp|udp] [<SOURCE-IP/MASK>|any|host <IP>] [eq <SOURCE-PORT>| range <START-PORT> <END-PORT>] [<DESTINATION-IP/MASK>|any|host <IP>] [eq [<DESTINATION-PORT>|bgp|dns|ftp|ftp- data|gopher|https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www]|range <START-PORT> <END-PORT>] (log,mark [8021p <0-7>|dscp <0-63>],rule-precedence <1-5000>) {rule-description <RULE-DESCRIPTION>} host <IP> Permits traffic to a specific host <IP> Specify the host IP address. log Logs all permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters. tcp Configures the ACL for TCP packets udp Configures the ACL for UDP packets <SOURCE-IP/MASK> Sets the IP address and mask as the source to permit access any Permits traffic from all potential sources host <IP> Permits traffic from a specific host <IP> Specify the host IP address. eq <SOURCE-PORT> Identifies the source port <SOURCE-PORT> Specify the source port. range <START-PORT> <END-PORT> Identifies the source port range <START-PORT> Specify the start of the range. <END-PORT> Specify the end of the range. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit access any Permits traffic to all destinations host <IP> Permits traffic to a specific host <IP> Specify the host IP address.
ip-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 821 Usage Guidelines Use this command to permit traffic between networks/hosts based on the protocol type selected in the access list. The following protocols are supported: ip icmp icp udp proto The last ACE in the access list is an implicit deny statement. eq [<DESTINATION-PORT> |bgp|dns|ftp|ftp-data|gopher| https|ldap|nntp|ntp|pop3| smtp|ssh|telnet|tftp|www] Identifies a specific destination or protocol port <DESTINATION-PORT> The destination port designated by its number bgp The designated BGP protocol port dns The designated DNS protocol port ftp The designated FTP protocol port ftp-data The designated FTP data port gropher The designated GROPHER protocol port https The designated HTTPS protocol port ldap The designated LDAP protocol port nntp The designated NNTP protocol port ntp The designated NTP protocol port pop3 The designated POP3 protocol port smtp The designated SMTP protocol port ssh The designated SSH protocol port telnet The designated Telnet protocol port tftp The designated TFTP protocol port www The designated www protocol port range <START-PORT> <END-PORT> Identifies the destination port range <START-PORT> Specify the start of the range. <END-PORT> Specify the end of the range. log Logs all permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 822 Whenever the interface receives the packet, its content is checked against all the ACEs in the ACL. It is allowed based on the ACL configuration. Filtering on TCP/UDP allows the user to specify port numbers as filtering criteria Select ICMP to allow/deny packets Selecting ICMP allows the filter of ICMP packets based on type and node. NOTE The log option is functional only for router ACLs. The log option displays an informational logging message about the packet matching the entry sent to the console. Example wm3400-34710C8(config-ip-acl-test)#show context ip access-list test deny proto vrrp any any log rule-precedence 600 deny proto ospf any any log rule-precedence 650 wm3400-34710C8(config-ip-acl-test)#permit ip 172.16.10.0/24 any log rule- precedence 750 wm3400-34710C8(config-ip-acl-test)#permit tcp 172.16.10.0/24 any log rule- precedence 800 wm3400-34710C8(config-ip-acl-test)#show context ip access-list test deny proto vrrp any any log rule-precedence 600 deny proto ospf any any log rule-precedence 650 permit ip 172.16.10.0/24 any log rule-precedence 750 permit tcp 172.16.10.0/24 any log rule-precedence 800 Related Commands mac-access-list Access List The following table summarizes MAC Access list commands no Resets values or disables IP access permit command Command Description Reference deny Use this command to specify packets to reject page 13-823 no Negates a command or sets its default value page 13-826 permit Use this command to specify packets to accept page 13-828 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380
mac-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 823 deny mac-access-list Specifies packets to reject NOTE Use a decimal value representation to implement a permit/deny designation for a packet. The command set for MAC ACLs provide the hexadecimal values for each listed EtherType. The controller supports all EtherTypes. Use the decimal equivalent of the EtherType listed for any other EtherType. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax deny [<SOURCE-MAC>|any|host deny [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|<1- 65535>|aarp|appletalk|arp|ip|ipv6|mint|rarp| wisp|ipx],vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 Command Description Reference
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 824 Parameters deny [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|<1- 65535>|aarp|appletalk|arp|ip|ipv6|mint|rarp| wisp|ipx],vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} <SOURCE-MAC> Configures the source MAC address for this ACL <SOURCE-MAC-MASK> Configures the source MAC address mask any Identifies all devices as the source to deny access host <MAC> Identifies a specific host as the source to deny access <MAC> Specify the MAC address of the host. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny access any Identifies all devices as the destination to deny access host <MAC> Identifies a specific host as the destination deny access <MAC> Specify the MAC address of the host. dotp1p <PRIORITY> Configures the 802.1p priority value. Sets the service classes for traffic handling <PRIORITY> Specify a value from 0 - 7. type [8021q|<1-65535?|aarp| appletalk |arp|ip|ipv6|mint|rarp| wisp|ipx] Configures the EtherType value An EtherType is a two-octet field in an Ethernet frame that indicates the protocol encapsulated in the payload of the frame The EtherType values are: 8021q Indicates a 802.1q payload <1-65535> Indicates the EtherType protocol number aarp Indicates the Appletalk Address Resolution Protocol (ARP) payload appletalk Indicates the Appletalk Protocol payload arp Indicates the ARP payload ip Indicates the Internet Protocol, Version 4 (IPv4) payload ipv6 Indicates the Internet Protocol, Version 6 (IPv6) payload mint Indicates the MiNT protocol payload rarp Indicates the Reverse Address Resolution Protocol payload wisp Indicates the Wireless Internet Service Provider (WISP) payload ipx Indicates the Novells IPX payload vlan <VLAN> Configures the VLAN where the traffic is received <VLAN> Specify the VLAN ID. log Logs all deny events mark [8021p <0-7>|dscp <0- 63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000.
mac-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 825 Usage Guidelines The deny command disallows traffic based on layer 2 (data-link layer) data. The MAC access list denies traffic from a particular source MAC address or any MAC address. It can also disallow traffic from a list of MAC addresses based on the source mask. The MAC access list can disallow traffic based on the VLAN and EtherType. arp wisp ip 802.1q NOTE MAC ACLs always takes precedence over IP based ACLs. The last ACE in the access list is an implicit deny statement. Whenever the interface receives the packet, its content is checked against all the ACEs in the ACL. It is allowed/denied based on the ACLs configuration. Example wm3400-34710C8(config-mac-acl-test)#deny 41-85-45-89-66-77 44-22-55-88-77- 99 any vlan 1 log rule-precedence 2 rule-description test wm3400-34710C8(config-mac-acl-test)# The MAC ACL (in the example below) denies traffic from any source MAC address to a particular host MAC address: wm3400-34710C8(config-mac-acl-test)#deny any host 00:01:ae:00:22:11 wm3400-34710C8(config-mac-acl-test)# The example below denies traffic between two hosts based on MAC addresses: wm3400-34710C8(config-mac-acl-test)#deny host 01:02:fe:45:76:89 host 01:02:89:78:78:45 wm3400-34710C8(config-mac-acl-test)# rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 826 Related Commands no mac-access-list Negates a command or sets its default Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [deny|permit] no [deny|permit] [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|<1- 65535>|aarp|appletalk|arp|ip|ipv6|mint|rarp| wisp|ipx],vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} Parameters no [deny|permit] [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|<1- 65535>|aarp|appletalk|arp|ip|ipv6|mint|rarp| wisp|ipx],vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} no Resets values or disables MAC access deny command <SOURCE-MAC> Configures the source MAC address for this ACL <SOURCE-MAC-MASK> Configures the source MAC address mask any Identifies all devices as the source to deny/permit access
mac-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 827 Example wm3400-34710C8(config-mac-acl-test)#show context mac access-list test permit host 11-22-33-44-55-66 any log mark 8021p 3 rule-precedence 600 permit host 22-33-44-55-66-77 host 11-22-33-44-55-66 type ip log rule- precedence 610 deny any host 33-44-55-66-77-88 log rule-precedence 700 host <MAC> Identifies a specific host as the source to deny/permit access <MAC> Specify the MAC address of the host. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to deny/permit access any Identifies all devices as the destination to deny/permit access host <MAC> Identifies a specific host as the destination to deny/permit access <MAC> Specify the MAC address of the host. dotp1p <PRIORITY> Configures the 802.1p priority value. Sets the service classes for traffic handling <PRIORITY> Specify a value from 0 - 7. type [8021q|<1-65535?|aarp| appletalk |arp|ip|ipv6|mint|rarp| wisp|ipx] Configures the EtherType value An EtherType is a two-octet field in an Ethernet frame that indicates the protocol encapsulated in the payload of the frame The EtherType values are: 8021q Indicates the 802.1q payload <1-65535> Indicates the EtherType protocol number aarp Indicates the Appletalk Address Resolution Protocol (ARP) payload appletalk Indicates the Appletalk Protocol payload arp Indicates the ARP payload ip Indicates the Internet Protocol, Version 4 (IPv4) payload ipv6 Indicates the Internet Protocol, Version 6 (IPv6) payload mint Indicates the MiNT protocol payload rarp Indicates the Reverse Address Resolution Protocol payload wisp Indicates the WISP payload ipx Indicates the Novells IPX payload vlan <VLAN> Configures the VLAN where the traffic is received <VLAN> Specify the VLAN ID. log Logs all deny/permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 828 wm3400-34710C8(config-mac-acl-test)#no deny any host 33-44-55-66-77-88 log rule-precedence 700 wm3400-34710C8(config-mac-acl-test)#show context mac access-list test permit host 11-22-33-44-55-66 any log mark 8021p 3 rule-precedence 600 permit host 22-33-44-55-66-77 host 11-22-33-44-55-66 type ip log rule- precedence 610 Related Commands permit ip-access-list Configures a permit MAC ACL NOTE Use a decimal value representation to implement a permit/deny designation for a packet. The command set for MAC ACLs provide the hexadecimal values for each listed EtherType. The controller supports all EtherTypes. Use the decimal equivalent of the EtherType listed for any other EtherType. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax permit [<SOURCE-MAC>|any|host permit [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|<1-65535>|aarp|appletalk |arp|ip|ipv6|mint|rarp| wisp|ipx],vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| deny Creates a MAC deny ACL permit Creates a MAC permit ACL
mac-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 829 mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} Parameters permit [<SOURCE-MAC> <SOURCE-MAC-MASK>|any|host <MAC>] [<DESTINATION-MAC> <DESTINATION-MAC-MASK>|any|host <MAC>] (dot1p <PRIORITY>,type [8021q|aarp|appletalk |arp|ip|ipv6|mint|rarp|wisp|ipx], vlan <VLAN>) [log mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]| mark [8021p <VLAN-PRIORITY>|dscp <DSCP>]|rule-precedence <1-5000>] {rule-description <RULE-DESCRIPTION>} <SOURCE-MAC> Configures the source MAC address for this ACL <SOURCE-MAC-MASK> Configures the source MAC address mask any Identifies all devices as the source to permit access host <MAC> Identifies a specific host as the source of traffic to permit access <MAC> Specify the MAC address of the host. <DESTINATION-IP/MASK> Sets the IP address and mask as the destination to permit access any Identifies all devices as the destination to permit access host <MAC> Identifies a specific host as the destination to permit access <MAC> Specify the MAC address of the host. dotp1p <PRIORITY> Configures the 802.1p priority value. Sets the service classes for traffic handling <PRIORITY> Specify a value from 0 - 7. type [8021q|<1-65535?|aarp| appletalk |arp|ip|ipv6|mint|rarp| wisp|ipx] Configures the EtherType value An EtherType is a two-octet field in an Ethernet frame that indicates the protocol encapsulated in the payload of the frame The EtherType values are: 8021q Indicates a 802.1q payload <1-65535> Indicates the EtherType protocol number aarp Indicates the AARP payload appletalk Indicates the Appletalk Protocol payload arp Indicates the ARP payload ip Indicates the Internet Protocol, Version 4 (IPv4) payload ipv6 Indicates the Internet Protocol, Version 6 (IPv6) payload mint Indicates the MiNT protocol payload rarp Indicates the Reverse Address Resolution Protocol payload wisp Indicates the WISP payload ipx Indicates the Novells IPX payload vlan <VLAN> Configures the VLAN where the traffic is received <VLAN> Specify the VLAN ID. log Logs all permit events mark [8021p <0-7>|dscp <0-63> Marks packets that match the ACL rule 8021p <0-7> Modifies 802.1p VLAN user priority from 0 - 7 dscp <0-63> Modifies DSCP TOS bits in the IP header from 0 - 63
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 830 Usage Guidelines The permit command in the MAC ACL disallows traffic based on layer 2 (data-link layer) information. A MAC access list permits traffic from a source MAC address or any MAC address. It also has an option to allow traffic from a list of MAC addresses (based on the source mask). The MAC access list can be configured to allow traffic based on VLAN information, or Ethernet type. Common types include: arp wisp ip 802.1q The controller (by default) does not allow layer 2 traffic to pass through the interface. To adopt an access point through an interface, configure an ACL to allow an Ethernet WISP. Use the mark option to specify the type of service (tos) and priority value. The tos value is marked in the IP header and the 802.1p priority value is marked in the dot1q frame. Whenever the interface receives the packet, its content is checked against all the ACEs in the ACL. It is marked based on the ACLs configuration. NOTE To apply an IP based ACL to an interface, a MAC access list entry is mandatory to allow ARP. A MAC ACL always takes precedence over IP based ACLs. Example wm3400-34710C8(config-mac-acl-test)#show context mac access-list test wm3400-34710C8(config-mac-acl-test)#permit host 11-22-33-44-55-66 any log mark 8021p 3 rule-precedence 600 wm3400-34710C8(config-mac-acl-test)#permit host 22-33-44-55-66-77 host 11- 22-33-44-55-66 type ip log rule-precedence 610 wm3400-34710C8(config-mac-acl-test)#show context mac access-list test permit host 11-22-33-44-55-66 any log mark 8021p 3 rule-precedence 600 permit host 22-33-44-55-66-77 host 11-22-33-44-55-66 type ip log rule- precedence 610 rule-precedence <1-5000> Sets the rule precedence. Rules are checked in the order of their rule precedence <1-5000> Specify the rule precedence from 1 - 5000. rule-description <RULE-DESCRIPTION> Optional. Sets the rule description <RULE-DESCRIPTION> Provide a description of the rule. The description should not exceed 128 characters.
mac-access-list Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 831 Related Commands no Resets values or disables MAC access permit command
Chapter 13: Access List Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 832
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 833 C H A P T E R 14 DHCP Server Policy This chapter summarizes DHCP server policy commands within CLI structure. Dynamic Host Control Protocol (DHCP) is a protocol that automatically assigns network IP addresses to clients to enable them to participate in the network. DHCP keeps track of IP address assignments, their lease times and their availability for use by clients. Use the (config) instance to configure DHCP server policy configuration commands. To navigate to the DHCP server policy instance, use the following commands: wm3400-34710C8(config)#dhcp-server-policy <POLICY-NAME> wm3400-34710C8(config)#dhcp-server-policy test wm3400-34710C8(config-dhcp-server-policy-test)# wm3400-34710C8(config-dhcp-policy-test)#? DHCP policy Mode commands: bootp BOOTP specific configuration dhcp-class Configure DHCP class (for address allocation using DHCP user-class options) dhcp-pool Configure DHCP server address pool no Negate a command or set its defaults option Define DHCP server option ping Specify ping parameters used by DHCP Server clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test)#
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 834 dhcp-server-policy The following tablesummarizes DHCP server policy commands bootp dhcp-server-policy Configures a BOOTP specific configuration. Bootstrap Protocol (BOOTP) is used by UNIX diskless workstations to obtain the network location of their boot image and IP address. A BOOP configuration server also assigns an IP address from a configured pool of IP addresses. Supported in the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax bootp ignore Command Description Reference bootp Configures a BOOTP specific configuration page 14-834 dhcp-class Configures a DHCP server class page 14-835 dhcp-pool Configures a DHCP server address pool page 14-840 no Negates a command or sets its default page 14-877 option Defines the DHCP option used in DHCP pools page 14-879 ping Specifies ping parameters used by a DHCP server page 14-880 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 6-381 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 835 Parameters bootp ignore Example wm3400-34710C8(config-dhcp-policy-test)#bootp ignore wm3400-34710C8(config-dhcp-policy-test)# Related Commands dhcp-class dhcp-server-policy A DHCP user class applies different DHCP settings to a set of wireless clients. These wireless clients are grouped under the same DHCP class. This class is configured on the DHCP server to provide differentiated service. dhcp-class dhcp-server-policy Configures a DHCP server class and opens a new mode. For more information, see dhcp-class-mode. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-class <DHCP-CLASS> bootp ignore Configures a BOOTP specific configuration ignore Configures a DHCP server to ignore BOOTP requests no Resets values or disables commands Command Description Reference dhcp-class Configures a DHCP class and its settings page 14-835
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 836 Parameters dhcp-class <DHCP-CLASS> Example wm3400-34710C8(config-dhcp-policy-test)#dhcp-class dhcpclass1 wm3400-34710C8(config-dhcp-policy-test-class-dhcpclass1)#? wm3400-34710C8(config-dhcp-policy-test-class-dhcpclass1)#? DHCP class Mode commands: multiple-user-class Enable multiple user class option no Negate a command or set its defaults option Configure DHCP Server options clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-class-dhcpclass1)# Related Commands dhcp-class-mode dhcp-class Use DHCP class mode commands to configure a DHCP server class. The following table summarizes DHCP class commands <DHCP-CLASS> Sets the DHCP class. If the class does not exist, it is created. no Resets values or disables commands Command Description Reference multiple-user-class Enables the multiple user class option page 14-837 no Negates a command or sets its default page 14-837 option Configures DHCP server options page 14-838 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 837 multiple-user-class dhcp-class-mode Enables the multiple user class option for the DHCP policy Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax multiple-user-class Parameters None Example wm3400-34710C8(config-dhcp-policy-test-class-class1)#multiple-user-class wm3400-34710C8(config-dhcp-policy-test-class-class1)# Related Commands no dhcp-class-mode exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 no Resets values or disables the DHCP user class commands Command Description Reference
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 838 Negates a command or sets its default Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [multiple-user-class|option] Parameters no multiple-user-class no option user-class <USER-CLASS> Example wm3400-34710C8(config-dhcp-policy-test-class-class1)#no multiple-user-class wm3400-34710C8(config-dhcp-policy-test-class-class1)# Related Commands option dhcp-class-mode Configures the DHCP server options for use with this DHCP user class no multiple-user-class Disables a multiple user class with this DHCP class no option Removes DHCP policy setting user-class <USER-CLASS> Removes the configured user class <USER-CLASS> Specify the user class name. multiple-user-class Configures a multiple user class with a DHCP user class option Configures DHCP user class options
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 839 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax option user-class <VALUE> Parameters option user-class <VALUE> Example wm3400-34710C8(config-dhcp-policy-test-class-class1)#option user-class hex wm3400-34710C8(config-dhcp-policy-test-class-class1)# Related Commands dhcp-pool dhcp-server-policy The DHCP pool commands create and manage a pool of IP addresses. These IP addresses are assigned to devices using the DHCP protocol. IP addresses have to be unique for each device in the network. As IP addresses are finite, DHCP mechanism enables the reuse of finite addresses by keeping track of their issue, release and reissue. The DHCP pool commands configure a finite set of IP addresses that can be assigned whenever a device joins a network. user-class <VALUE> Configures a DHCP user class options <VALUE> Specify the DHCP user class option. no Resets values or disables DHCP user class commands Command Description Reference dhcp-pool Configures the DHCP pool parameters 14-840
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 840 dhcp-pool dhcp-server-policy Configures a DHCP server address pool. An address pool is a set of IP addresses allocated to devices as they are authorized to access network resources. This enables the reuse of limited IP address resources for deployment in any network. A separate instance opens where you can configure DHCP pool parameters. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-pool <POOL-NAME> Parameters dhcp-pool <POOL-NAME> Example wm3400-34710C8(config-dhcp-policy-test)#dhcp-pool pool1 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#? wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#? DHCP pool Mode commands: address Configure network pool's included addresses bootfile Boot file name ddns Dynamic DNS Configuration default-router Default routers dns-server DNS Servers domain-name Configure domain-name excluded-address Prevent DHCP Server from assigning certain addresses lease Address lease time netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type network Network on which DHCP server will be deployed next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options <POOL-NAME> Configures a policy <POOL-NAME> to specify DHCP pool parameters
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 841 respond-via-unicast Send DHCP offer and DHCP Ack as unicast messages static-binding Configure static address bindings static-route Add static routes to be installed on dhcp clients update Control the usage of DDNS service clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands dhcp-pool-mode dhcp-pool Configures the DHCP pool commands The following table summarizes DHCP pool commands no Resets values or disables commands Command Description Reference address Specifies a range of addresses for a DHCP pool page 14-842 bootfile Assigns a bootfile name. The bootfile name can contain letters, numbers, dots and hyphens. Consecutive dots and hyphens are not permitted page 14-843 ddns Configures dynamic DNS parameters page 14-843 default-router Configures a default-router or gateway IP address for the network pool page 14-845 dns-server Sets the DNS servers IP address available to all DHCP clients connected to the DHCP pool page 14-846 domain-name Sets the domain name for the network pool page 14-847 excluded-address Prevents a DHCP server from assigning certain addresses to the DHCP pool page 14-847 lease Sets a valid lease for the IP address used by DHCP clients in the DHCP pool page 14-848 netbios-name-server Configures NetBIOS (WINS) name server IP address page 14-850 netbios-node-type Defines the NetBIOS node type page 14-851 next-server Configures the next server in the boot process page 14-852 no Negates a command or sets its default page 14-852 option Configures RAW DHCP options page 14-856
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 842 address dhcp-pool-mode Specifies a range of addresses for the DHCP pool. This is the range of IP addresses assigned to each device that joins the network. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax address [<IP>|range <START-IP> <END-IP>] {class <DHCP-CLASS>} Parameters address [<IP>|range <START-IP> <END-IP>] {class <DHCP-class>} Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#address range 1.2.3.4 5.6.7.8 class dhcp1 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#address 1.2.3.4 class dhcp1 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# respond-via-unicast Sends a DHCP offer and a DHCP Ack as unicast messages page 14-857 update Controls the usage of DDNS service page 14-860 static-binding Configures static address bindings page 14-861 <IP> Adds a single IP address to the DHCP pool range <START-IP> <END-IP> Adds a range of IP addresses to the DHCP pool <START-IP> Specify the first IP address in the range. <END-IP> Specify the last IP address in the range. class <DHCP-CLASS> Applies additional DHCP options, or a modified set of options to those available to wireless clients. For more information, see dhcp-class. <DHCP-CLASS> Sets the DHCP class to use. Command Description Reference
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 843 Related Commands bootfile dhcp-pool-mode The Bootfile command provides a diskless node path to the image file while booting up. Only one file can be configured for each DHCP pool. For more information on the BOOTP protocol with reference to the DHCP policy, see bootp. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax bootfile <IMAGE-FILE-PATH> Parameters bootfile <IMAGE-FILE-PATH> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#bootfile test.txt wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands ddns dhcp-pool-mode no Resets values or disables DHCP pool address commands dhcp-class Creates and configures DHCP class parameters <IMAGE-FILE-PATH> Sets the path to the boot image for BOOTP clients. The file name can contain letters, numbers, dots and hyphens. Consecutive dots and hyphens are not permitted no Resets values or disables bootfile commands bootp Configures the BOOTP protocol parameters
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 844 Configures Dynamic DNS (DDNS) parameters. Dynamic DNS provides a way to access an individual device in a DHCP serviced network using a static device name. Depending on the DHCP server configuration, the IP address of a device changes periodically. To enable the device to be accessible, its current IP address has to be published to a server that can resolve the static device name used to access the device with its changing IP address. This server, the DDNS server, must be accessible from outside the network and must be configured as an address resolver. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ddns [domainname|multiple-user-class|server|ttl ddns domainname <DDNS-DOMAIN-NAME> ddns multiple-user-class ddns server <DDNS-SERVER-1> {<DDNS-SERVER-2>} ddns ttl <1-864000> Parameters ddns domainname <DDNS-DOMAIN-NAME> ddns multiple-user-class ddns server <DDNS-SERVER-1> {<DDNS-SERVER-2>} ddns ttl <1-86400> domainname <DDNS-DOMAIN-NAME> Sets the domain name multiple-user-class Enables the use of multiple user class with this DDNS domain server Configures the DDNS server used by this DHCP profile <ddns-server-1> Configures the first DDNS server. This is the default server. <ddns-server-2> Optional. Configures the second DDNS server. This server is used when the server defined in the <DDNS-SERVER-1> parameter is not reachable. ttl <1-864000> Configures the Time To Live (TTL) value for DDNS updates <1-86400> Specify a value between 1- 86400 seconds.
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 845 Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#ddns domainname WID wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#ddns multiple-user-class wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#ddns server 172.16.10.9 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands default-router dhcp-pool-mode Configures a default router or gateway IP address for the network pool Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax default-router <IP> {<IP1>} Parameters default-router <IP> {<IP1>} Usage Guidelines The IP address of the router should be on the same subnet as the client subnet. no Resets values or disables DHCP pool DDNS commands <IP> Configures the primary router for this network <IP1> Configures the secondary router for this network. If the primary router is not available, this router is used.
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 846 Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#default-router 172.16.10.8 172.16.10.9 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands dns-server dhcp-pool-mode Configures the DNS server for this network. This DNS server supports all clients connected to the network supported by the DHCP server. For DHCP clients, the DNS servers IP address maps the hostname to an IP address. DHCP clients use the DNS servers IP address based on the order (sequence) configured. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dns-server <IP> Parameters dns-server <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#dns-server 172.16.10.7 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# no Resets values or disables the DHCP pool default router commands <IP> Configures the DNS servers IP address <IP> Sets the server's IP address. Up to 8 IPs can be set
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 847 Related Commands domain-name dhcp-pool-mode Sets the domain name for the DHCP pool For DHCP clients, the DNS servers IP address maps the hostname to an IP address. DHCP clients use the DNS servers IP address based on the order (sequence) configured. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax domain-name <DOMAIN-NAME> Parameters domain-name <DOMAIN-NAME> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#domain-name documentation wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands excluded-address dhcp-pool-mode Prevents a DHCP server from assigning certain addresses in the DHCP pool no Resets values or disables the DHCP pool DNS server commands <DOMAIN-NAME> Defines the domain name for the DHCP pool no Resets values or disables the DHCP pool domain name commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 848 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax excluded-address [<IP>|range] excluded-address <IP> excluded-address range <START-IP> <END-IP> Parameters excluded-address <IP> excluded-address range <START-IP> <END-IP> Example wm3400-34710C8(config-dhcp-policy-test)#excluded-address range 172.16.10.9 172.16.10.10 wm3400-34710C8(config-dhcp-policy-test)#excluded-address 172.16.10.101 Related Commands lease dhcp-pool-mode The lease is the duration a DHCP issued IP address is valid for a DHCP client. Once this lease expires, and if the lease is not renewed, the IP address is revoked and is available for reuse. Generally, before an IP lease expires, the client tries to get the same IP address issued for the next lease period. The lease period is about 24 hours. <IP> Excludes a single IP address in the DHCP pool range <START-IP> <END-IP> Excludes a range of IP addresses in the DHCP pool no Resets values or disables DHCP pool excluded address commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 849 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax lease [<0-365>|infinite] lease infinite lease <0-365> {0-23} {0-59} {0-59} Parameters lease infinite lease <0-365> {<0-23>} {<0-59>} {<0-59>} Usage Guidelines If lease parameter is not configured on the DHCP pool, the default is used. The default is 24 hours. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#lease 1 0 0 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# show running-config include-factory .......................................... ip dhcp pool Test4lease lease 1 0 0 no domain-name no bootfile no dns-server no default-router infinite The lease never expires. Equal to a static IP address assignment <0-365> Configures the number of days for the lease <0-23> Optional. Sets the number of hours for the lease <0-59> Optional. Sets the number of minutes for the lease <0-59> Optional. Sets the number of seconds for the lease
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 850 no next-server no netbios-name-server no netbios-node-type no unicast-enable no update dns no ddns domainname no ddns ttl no ddns multiple-user-class client-name test4lease client-identifier tested4lease ................................................................ .......................................... wm3400-34710C8(config-dhcp-policy-test-pool-pool1))# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#lease infinite wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands netbios-name-server dhcp-pool-mode Configures the NetBIOS (WINS) name servers IP address. This server is used to resolve NetBIOS host names. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax netbios-name-server <IP> Parameters netbios-name-server <IP> no Resets values or disables the DHCP pool lease commands <IP> Configures the IP address of the NetBIOS server for this DHCP pool
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 851 Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#netbios-name-server 172.16.10.23 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands netbios-node-type dhcp-pool-mode Configures the predefined NetBIOS node type. The NetBIOS node type resolves NetBIOS names to IP addresses. Defines the NetBIOS node type Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax netbios-node-type [b-node|h-mode|m-node|p-node] Parameters netbios-node-type [b-node|h-node|m-node|p-node] Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#netbios-node-type b-node wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# no Resets values or disables the DHCP pool NetBIOS name server commands [b-node|h-mode|m-node| p-node] Defines the netbios node type b-node Sets the type as broadcast node h-node Sets the type as hybrid node m-node Sets the type as mixed node p-node Sets the type as peer-to-peer node
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 852 Related Commands next-server dhcp-pool-mode Configures the next server in the boot process Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax next-server <IP> Parameters next-server <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#next-server 172.16.10.24 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands no dhcp-pool-mode Negates a command or sets its default no Resets values or disables the DHCP pool NetBIOS node type commands <IP> Configures the IP address of the next server in the boot process no Resets values or disables the DHCP pool next server commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 853 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [address|bootfile|ddns|default-router|dns-server|domain-name| excluded-address|lease|netbios-name-server|netbios-node-type|network| next-server|option|respond-via-unicast|static-binding|static-route|update] no [bootfile|default-router|dns-server|domain-name|lease|netbios-name- server| netbios-node-type|next-server|network|respond-via-unicast] no address [<IP>|all] no address range <START-IP> <END-IP> no ddns [domainname|multiple-user-class|server|ttl] no excluded-address <IP> no excluded-address range <START-IP> <END-IP> no option <OPTION-NAME> no static-binding client-identifier <CLIENT-IDENTIFIER> no static-binding hardware-address <MAC> no static-route <IP/MASK> <GATEWAY-IP> no update dns {override} Parameters no [bootfile|default-router|dns-server|domain-name|lease|netbios-name- server| netbios-node-type|next-server|network|respond-via-unicast] no bootfile Removes a BOOTP bootfile configuration no default-router Removes the configured default router for the DHCP pool no dns-server Removes the configured DNS server for the DHCP pool no domain-name Removes the configured DNS domain name no lease Resets the lease to its default (24 hours) no netbios-name-server Removes the configured NetBIOS name server
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 854 no address [<IP>|all] no address range <START-IP> <END-IP> no ddns [domainname|multiple-user-class|server|ttl] no excluded-address <IP> no excluded-address range <START-IP> <END-IP> no option <OPTION-NAME> no netbios-node-type Removes the NetBIOS node type no next-server Removes the next server utilized in the boot process no network Removes the DHCP server network information no respond-via-unicast Resets sending the DHCP offer and ACK as broadcast message instead of unicast no address Resets configured DHCP pool addresses <IP> Removes an IP address from the list of addresses all Removes configured DHCP IP addresses no address Resets the DHCP pool addresses range <START-IP> <END-IP> Removes a range of IP address from the list of addresses <START-IP> Specify the first IP address in the range. <END-IP> Specify the last IP address in the range. no ddns Resets DDNS parameters domainname Removes DDNS domain name information multiple-user-class Resets the use of a multiple user class with the DDNS server Removes configured DDNS servers ttl Resets the TTL information for DDNS updates no excluded-address <IP> Removes an excluded IP address from the list of addresses that cannot be issued by the DHCP server <IP> Specify the IP address. no excluded-address Removes a range of excluded IP addresses from the list of addresses that cannot be issued by the DHCP server range <START-IP> <END-IP> Specifies the IP address range <START-IP> Specify the first IP address in the range. <END-IP> Specify the last IP address in the range. no option Resets DHCP option information <OPTION-NAME> Defines the DHCP option
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 855 no static-binding client-identifier <CLIENT-IDENTIFIER> no static-binding hardware-address <MAC> no static-route <IP/MASK> <GATEWAY-IP> no update dns {override} Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#no bootfile wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#no network wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#no lease wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#no default-router wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# no static-binding Removes static bindings for DHCP client client-identifier <CLIENT-IDENTIFIER> Resets client identifier information <CLIENT-IDENTIFIER> Specify the client identifier. no static-binding Removes static bindings for DHCP client hardware-address <MAC> Resets information based on the hardware address <MAC> Specify the hardware MAC address. no static-route Removes static routes for this DHCP pool <IP/MASK> Removes routing information for a particular subnet <GATEWAY-IP> Removes the gateway information for a particular subnets routing information no update dns Removes DDNS settings override Removes DDNS updates on an onboard DHCP server
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 856 Related Commands option dhcp-pool-mode Configures raw DHCP options. The DHCP option must be configured under the DHCP server policy. The options configured under the DHCP pool/DHCP server policy can also be used in static-bindings. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax option <option-name> [<A.B.C.D>|<WORD>] Parameters option <OPTION-NAME> [<DHCP-OPTION-IP>|<DHCP-OPTION-ASCII>] address Configures the DHCP servers IP address pool bootfile Configures the BOOTP boot file path ddns Configures DDNS for use with this DHCP pool default-router Configures default routers for this DHCP pool dns-server Configures default DNS servers for this DHCP pool domain-name Configures the DDNS domain name for this DHCP pool excluded-address Configures IP addresses assigned as static addresses lease Configures the DHCP lease netbios-name-server Configures the NetBIOS name server netbios-node-type Configures the NetBIOS node type next-server Configures the next server in the BOOTP boot process option Configures the DHCP option respond-via-unicast Configures how a DHCP request and ACK are sent static-binding Configure static binding information static-route Configures static routes installed on DHCP clients update Controls the usage of DDNS service <OPTION-NAME> Sets the name of the DHCP option <DHCP-OPTION-IP> Sets the DHCP option as an IP address
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 857 Usage Guidelines Defines non standard DHCP option codes (0-254) NOTE An option name in ASCII format accepts backslash (\) as an input but is not displayed in the output (Use show runnig config to view the output). Use a double backslash to represent a single backslash. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#option option1 157.235.208.80 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands respond-via-unicast dhcp-pool-mode Sends a DHCP offer and a DHCP Ack as unicast messages Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax respond-via-unicast Parameters None <DHCP-OPTION-ASCII> Sets the DHCP option as an ASCII string no Resets values or disables the DHCP pool option commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 858 Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#respond-via-unicast wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands static-binding static-binding Configures static address bindings. For more information, see static-binding. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax static-binding [client-identifier <CLIENT>|hardware-address <MAC>] Parameters static-binding [client-identifier <CLIENT>|hardware-address <MAC>] Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#static-binding client- identifier test wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-test)#? DHCP static binding Mode commands: bootfile Boot file name client-name Client name default-router Default routers no Resets values or disables the DHCP pool respond-via-unicast commands client-identifier <CLIENT> Enables a static binding configuration for a client based on its client identifier (as provided by DHCP option 61 and its key value) <CLIENT> Specify the client identifier (DHCP option 61). hardware-address <MAC> Enables a static binding configuration for a client based on its MAC address <MAC> Specify the MAC address of the client.
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 859 dns-server DNS Servers domain-name Configure domain-name ip-address Fixed IP address for host netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options respond-via-unicast Send DHCP offer and DHCP Ack as unicast messages static-route Add static routes to be installed on dhcp clients clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-Hex)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-11-22-33-44-55- 66)#? DHCP static binding Mode commands: bootfile Boot file name client-name Client name default-router Default routers dns-server DNS Servers domain-name Configure domain-name ip-address Fixed IP address for host netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options respond-via-unicast Send DHCP offer and DHCP Ack as unicast messages static-route Add static routes to be installed on dhcp clients clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-11-22-33-44-55- 66)#
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 860 Related Commands static-route dhcp-pool-mode Configures a static route for a DHCP pool. Static routes define a gateway for traffic intended for other networks. This gateway is always used when an IP address does not match any route in the network. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax static-route <IP/M> <IP>] Parameters static-route <IP/M> <IP>] Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#static-route 1.2.3.4/8 5.6.7.8 wm3400-34710C8(config-dhcp-policy-test-pool-pool1) wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#show context dhcp-pool pool1 static-route 1.2.3.4/8 5.6.7.8 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# update dhcp-pool-mode Controls the use of the DDNS service no Resets values or disables the DHCP policy static binding commands static-binding Describes the static binding mode commands <IP/M> Specifies the IP destination prefix (For example, 10.0.0.0/8) <IP> Specified the gateway IP address
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 861 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax update dns {override} Parameters update dns {override} Usage Guidelines A DHCP client cannot perform updates for RRs A, TXT and PTR. Use updat e ( dns) ( over r i de) to enable the controllers internal DHCP server to send DDNS updates for resource records. The DHCP server can override the client, even if the client is configured to perform the updates. In the DHCP pool of DHCP server, FQDN is configured as the DDNS domain name. This is used internally in DHCP packets between the controllers DHCP server and the DNS server. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#update dns override wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands static-binding dhcp-pool-mode dns {override} Configures the DDNS parameters override Optional. Enables DDNS updates on a onboard DHCP server no Resets values or disables commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 862 Configures static IP address information for a particular device. Static address binding is executed on the devices hostname, client identifier, or MAC address. Static bindings allow the configuration of client parameters, such as DHCP server, DNS server, default routers, fixed IP address etc. static-binding static-binding Configures static address bindings Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax static-binding [client-identifier <CLIENT>|hardware-address <MAC>] Parameters static-binding [client-identifier <CLIENT>|hardware-address <MAC>] Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#static-binding client- identifier test wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-test)#? DHCP static binding Mode commands: bootfile Boot file name client-name Client name default-router Default routers dns-server DNS Servers domain-name Configure domain-name ip-address Fixed IP address for host Command Description Reference static-binding Configures a static binding policy page 14-862 client-identifier <CLIENT> Enables static binding configuration for a client based on its client identifier as provided by DHCP option 61 and its key value <CLIENT> Set the client identifier specified with DHCP option 61. hardware-address <MAC> Enables static binding configuration for a client based on its MAC address <MAC> Specify the clients MAC address.
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 863 netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options respond-via-unicast Send DHCP offer and DHCP Ack as unicast messages static-route Add static routes to be installed on dhcp clients clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-Hex)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-11-22-33-44-55- 66)#? DHCP static binding Mode commands: bootfile Boot file name client-name Client name default-router Default routers dns-server DNS Servers domain-name Configure domain-name ip-address Fixed IP address for host netbios-name-server NetBIOS (WINS) name servers netbios-node-type NetBIOS node type next-server Next server in boot process no Negate a command or set its defaults option Raw DHCP options respond-via-unicast Send DHCP offer and DHCP Ack as unicast messages static-route Add static routes to be installed on dhcp clients clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-11-22-33-44-55- 66)#
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 864 Related Commands static-binding-mode The following table summarizes static binding mode commands bootfile static-binding-mode The Bootfile command provides a diskless node the path to the image file used while booting up. Only one file can be configured for each static IP binding. For more information on the BOOTP protocol with reference to static binding, see bootp. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax bootfile <IMAGE-FILE-PATH> no Resets values or disables the DHCP policy DHCP pool commands Command Description Reference bootfile Assigns a bootfile name for the DHCP configuration on the network pool page 14-864 client-name Configures a client name page 14-865 default-router Configures default router or gateway IP address page 14-866 dns-server Sets the DNS servers IP address available to all DHCP clients connected to the DHCP pool page 14-867 domain-name Sets the domain name for the network pool page 14-867 ip-address Configures a fixed IP address for a host page 14-868 netbios-name-server Configures a NetBIOS (WINS) name server IP address page 14-869 netbios-node-type Defines the NetBIOS node type page 14-870 next-server Specifies the next server used in the boot process page 14-871 no Negates a command or sets its default value page 14-872 option Configures raw DHCP options page 14-874 respond-via-unicast Sends a DHCP offer and DHCP Ack as unicast messages page 14-875 static-route Adds static routes to be installed on DHCP clients page 14-876
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 865 Parameters bootfile <IMAGE-FILE-PATH> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#bootfile test.txt wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands client-name static-binding-mode Specifies a name for a client Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax client-name <NAME> Parameters client-name <NAME> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#client-name RFID wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# <IMAGE-FILE-PATH> Sets the path to the boot image for BOOTP clients. The file name can contain letters, numbers, dots and hyphens. Consecutive dots and hyphens are not permitted no Resets values or disables DHCP pool static binding commands bootp Configures BOOTP protocol parameters <NAME> Specify a name for a client where this static binding policy is applied
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 866 Related Commands default-router dhcp-pool-mode Configures a default router or gateway IP address for the static binding configuration Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax default-router <IP> {<IP1>} Parameters default-router <IP> {<IP1>} Usage Guidelines The IP address of the router should be on the same subnet as the client subnet. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#default-router 172.16.10.8 172.16.10.9 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# no Resets values or disables DHCP pool static binding commands <IP> Configures the network primary router <IP1> Configures the secondary network router. If the primary router is not available, this router is used.
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 867 Related Commands dns-server dhcp-pool-mode Configures the DNS server for this static binding configuration. This DNS server supports the client for which the static binding has been configured. For this client, the DNS servers IP address maps the host name to an IP address. DHCP clients use the DNS servers IP address based on the order (sequence) configured. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dns-server <IP> Parameters dns-server <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#dns-server 172.16.10.7 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands domain-name dhcp-pool-mode Sets the domain name for the static binding configuration no Resets values or disables DHCP pool static binding commands <IP> Configures the DNS servers IP address <IP> Sets the server's IP address (up to 8 IPs can be set) no Resets values or disables DHCP pool static binding commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 868 For this client, the DNS servers IP address maps the host name to an IP address. DHCP clients use the DNS servers IP address based on the order (sequence) configured. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax domain-name <DOMAIN-NAME> Parameters domain-name <DOMAIN-NAME> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#domain-name documentation wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands ip-address static-binding-mode Configures a fixed IP address for a host <DOMAIN-NAME> Defines the domain name for the static binding configuration no Resets values or disables the DHCP pool static binding commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 869 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip-address <IP> Parameters ip-address <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#ip-address 172.16.10.9 wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# Related Commands netbios-name-server static-binding-mode Configures the NetBIOS (WINS) name servers IP address. This server is used to resolve NetBIOS host names. <IP> Configures a fixed host IP address in dotted decimal format no Resets values or disables DHCP pool static binding commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 870 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax netbios-name-server <IP> Parameters netbios-name-server <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#netbios-name- server 172.16.10.23 wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# Related Commands netbios-node-type static-binding-mode Configures different predefined NetBIOS node types. The NetBIOS node defines the way a device resolves NetBIOS names to IP addresses. <IP> Configures the NetBIOS server IP address no Resets values or disables DHCP pool static binding commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 871 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax netbios-node-type [b-node|h-mode|m-node|p-node] Parameters netbios-node-type [b-node|h-node|m-node|p-node] Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#netbios-node- type b-node wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# Related Commands next-server static-binding-mode Configures the next server utilized in the boot process [b-node|h-mode| m-node|p-node] Defines the netbios-node-type b-node Sets the broadcast node h-node Sets the hybrid node m-node Sets the mixed node p-node Sets the peer-to-peer node no Resets values or disables DHCP pool static binding commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 872 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax next-server <IP> Parameters next-server <IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#next-server 172.16.10.24 wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# Related Commands no dhcp-pool-mode Negates a command or sets its default for the static binding commands <IP> Configures the IP address of the next server utilized in the boot process no Resets values or disables DHCP pool static binding commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 873 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [bootfile|client-name|default-router|dns-server|domain-name| ip-address|netbios-name-server|netbios-node-type|next-server|option| respond-via-unicast|static-route] no [bootfile|client-name|default-router|dns-server|domain-name|ip-address| netbios-name-server|netbios-node-type|next-server|respond-via- unicast] no option <OPTION-NAME> no static-route <IP/MASK> <GATEWAY-IP> Parameters no [bootfile|default-router|dns-server|domain-name|lease|netbios-name- server| netbios-node-type|next-server|network|respond-via-unicast] no option <OPTION-NAME> bootfile Removes the BOOTP bootfile configuration client-name Removes the client name from the static binding configuration default-router Removes default router from the static binding configuration dns-server Removes the DNS server from the static binding configuration domain-name Removes the DNS ip-address Removes IP addresses from the static binding configuration netbios-name-server Removes the NetBIOS name server netbios-node-type Removes the NetBIOS node type next-server Removes the next server utilized in the boot process respond-via-unicast Resets sending the DHCP offer and ACK as broadcast message instead of unicast option Resets DHCP option information <OPTION-NAME> Defines the DHCP option
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 874 no static-route <IP/MASK> <GATEWAY-IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#no bootfile wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#no ip-address wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#no respond- via-unicast wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#no default- router wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)# Related Commands option static-binding-mode Configures raw DHCP options. The DHCP option has to be configured in the DHCP policy. The options configured in the DHCP server policy can only be used in static bindings. static-route Removes static routes from the static binding configuration <IP/MASK> Removes information for a particular subnet <GATEWAY-IP> Removes gateway information from a particular subnets routing information bootfile Configures the path to the BOOTP boot file client-name Configures the hostname for this host default-router Configures default routers for this DHCP pool dns-server Configures default DNS servers for this DHCP pool domain-name Configures the DDNS domain name for this DHCP pool ip-address Configures IP addresses assigned to this host netbios-name-server Configures the NetBIOS name server netbios-node-type Configures the NetBIOS node type next-server Configures the next server utilized in the BOOTP boot process option Configures the DHCP option respond-via-unicast Configures how DHCP request and ACK are sent static-route Configures the static route for this static binding configuration
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 875 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax option <OPTION-NAME> [<DHCP-OPTION-IP>|<DHCP-OPTION-ASCII>] Parameters option <OPTION-NAME> [<DHCP-OPTION-IP>|<DHCP-OPTION-ASCII>] Usage Guidelines Defines non standard DHCP option codes (0-254) NOTE An option name in ASCII format accepts a backslash (\) as an input, but is not displayed in the output (Use show runnig config to view the output). Use a double backslash to represent a single backslash. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-ascii)#option option1 172.16.10.10 wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-ascii)# respond-via-unicast static-binding-mode Sends a DHCP offer and a DHCP acknowledge as unicast messages <OPTION-NAME> Sets the DHCP option name <DHCP-OPTION-IP> Sets the DHCP option as an IP address <DHCP-OPTION-ASCII> Sets the DHCP option as an ASCII string
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 876 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax respond-via-unicast Parameters None Example wm3400-34710C8(config-dhcp-net-pool-test)#respond-via-unicast wm3400-34710C8(config-dhcp-net-pool-test)# Related Commands static-route static-binding-mode Adds static routes to the static binding configuration no Resets values or disables DHCP pool static binding commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 877 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax static-route <IP/MASK> <GATEWAY-IP> Parameters static-route <IP/MASK> <GATEWAY-IP> Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#static-route 10.0.0.0/10 157.235.208.235 wm3400-34710C8(config-dhcp-policy-test-pool-pool1-binding-1)#? Related Commands no dhcp-server-policy Negates a command or sets its default for DHCP policy commands <IP/MASK> Sets the subnet for which the static route is configured <GATEWAY-IP> Specify the gateway IP address no Resets values or disables DHCP pool static route commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 878 Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [bootp|dhcp-class|dhcp-pool|option|ping] no bootp ignore no dhcp-class <DHCP-CLASS> no dhcp-pool <DHCP-POOL> no option <DHCP-OPTION> no ping timeout Parameters no bootp ignore no dhcp-class <DHCP-CLASS> no dhcp-pool <DHCP-POOL> no option <DHCP-OPTION> no bootp Removes the BOOTP specific configuration ignore Removes the DHCP server ignoring BOOTP requests no dhcp-class Removes a DHCP class <DHCP-CLASS> Sets the DHCP class name no dhcp-pool Removes a DHCP pool <DHCP-POOL> Sets the DHCP pool name no option Removes a DHCP option <dhcp-option> Sets the DHCP option
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 879 no ping timeout Example wm3400-34710C8(config-dhcp-policy-test)#no bootp ignore wm3400-34710C8(config-dhcp-policy-test)# wm3400-34710C8(config-dhcp-policy-test)#no option test1 wm3400-34710C8(config-dhcp-policy-test)# Related Commands option dhcp-pool-mode Configures raw DHCP options. The DHCP option has to be configured in the DHCP server policy. The options configured in the DHCP pool/DHCP server policy can also be used in static bindings. Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax option <OPTION-VALUE> <OPTION> [ascii|hexstring|ip] Parameters option <OPTION-VALUE> <OPTION> [ascii|hexstring|ip] no ping timeout Resets the DHCP server ping timeout timeout Resets the timeout to its default bootp Configures BOOTP protocol parameters dhcp-class Configures DHCP user class parameters dhcp-pool Configures the DHCP pool option Configures DHCP option values ping Configures the DHCP ping timeout <OPTION-VALUE> Configures the option specified by the <OPTION> number
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 880 Usage Guidelines Defines non standard DHCP option codes (0-254) NOTE An option name in ASCII format accepts a backslash (\) as an input, but is not displayed in the output (Use show runnig config to view the output). Use a double backslash to represent a single backslash. Example wm3400-34710C8(config-dhcp-policy-test-pool-pool1)#option option1 157.235.208.80 wm3400-34710C8(config-dhcp-policy-test-pool-pool1)# Related Commands ping dhcp-server-policy Specifies DHCP server ping parameters Supported on the following platforms: AP4021 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ping timeout <1-10> <OPTION> Configures the DHCP option ascii Configures the DHCP option as an ASCII string hexstring Configures the DHCP option as a hexadecimal string ip Configures the DHCP option as an IP address no Resets values or disables commands
dhcp-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 881 Parameters ping timeout <1-10> Example wm3400-34710C8(config-dhcp-policy-test)#ping timeout 2 wm3400-34710C8(config-dhcp-policy-test)# Related Commands timeout <1-10> Sets the ping timeout from 1 - 10 seconds no Resets values or disables commands
Chapter 14: DHCP Server Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 882
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 883 C H A P T E R 15 Firewall Policy A firewall protects a network from attacks and unauthorized access from outside the network. Simultaneously, it allows authorized users to access required resources. Firewalls work on multiple levels. Some work at layers 1 and 2 and 3 to inspect each packet. The packet is either passed, dropped or rejected based on rules configured on the firewall. Firewalls use application layer filtering to enforce compliance. These firewalls can understand applications and protocols and can detect if an unauthorized protocol is being used, or an authorized protocol is being abused in any malicious way. The third set of firewalls, Stateful Firewalls, consider the placement of individual packets within each packet in the series of packets being transmitted. If there is a packet that does not fit into the sequence, it is automatically identified and dropped. This chapter summarizes the firewall policy commands within the CLI structure. Use (config) instance to configure firewall policy commands. To navigate to the config-fw-policy instance, use the following commands: wm3400-34710C8(config)#firewall-policy <POLICY-NAME> wm3400-34710C8(config)#firewall-policy test wm3400-34710C8(config-fw-policy-test)#? Firewall policy Mode commands: alg Enable ALG clamp Clamp value dhcp-offer-convert Enable conversion of broadcast dhcp offers to unicast dns-snoop DNS Snooping firewall Wireless firewall flow Firewall flow ip Internet Protocol (IP) ip-mac Action based on ip-mac table logging Firewall enhanced logging no Negate a command or set its defaults proxy-arp Enable generation of ARP responses on behalf of another device
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 884 stateful-packet-inspection-l2 Enable stateful packet inspection in layer2 firewall storm-control Storm-control virtual-defragmentation Enable virtual defragmentation for IPv4 packets (recommended for proper functioning of firewall) clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-fw-policy-test)# firewall-policy The following table summarizes default firewall policy commands Command Description Reference alg Enables an algorithm page 15-885 clamp Sets a clamp value to limit TCP MSS to inner path-MTU for tunnelled packets page 15-886 dhcp-offer-convert Enables the conversion of broadcast DHCP offers to unicast page 15-887 dns-snoop Sets the timeout value for DNS entries page 15-887 firewall Configures the wireless firewall page 15-888 flow Defines a session flow timeout page 15-889 ip Sets an IP address for a selected device page 15-891 ip-mac Defines an action based on IP-MAC table page 15-896 logging Enables enhanced firewall logging page 15-899 no Negates a command or sets its default value page 15-900 proxy-arp Enables the generation of ARP responses on behalf of another device page 15-907 stateful-packet- inspection-12 Enables stateful packets-inspection in layer 2 firewall page 15-908 storm-control Defines storm control and logging settings page 15-908 virtual- defragmentation Enables virtual defragmentation for IPv4 packets page 15-911 clrscr Clears the display screen page 6-379
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 885 alg firewall-policy Enables preconfigured algorithms supporting a particular protocol Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax alg [dns|ftp|sip|tftp] Parameters alg [dns|ftp|sip|tftp] commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts the changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420 alg Enables preconfigured algorithms (dns, ftp, sip, and tftp) dns Enables the Domain Name System (DNS) algorithm ftp Enables the File Transfer Protocol (FTP) algorithm sip Enables the Session Initiation Protocol (SIP) algorithm tftp Enables the Trivial File Transfer Protocol (TFTP) algorithm Command Description Reference
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 886 Example wm3400-34710C8(config-fw-policy-test)# alg tftp wm3400-34710C8(config-fw-policy-test)#show context firewall policy test no ip dos tcp-sequence-past-window Related Commands clamp firewall-policy This option limits the TCP Maximum Segment Size (MSS) to the size of the Maximum Transmission Unit (MTU) discovered by path MTU discovery for the inner protocol. This ensures the packet traverses through the inner protocol without fragmentation. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax clamp tcp-mss Parameters clamp tcp-mss Example wm3400-34710C8(config-fw-policy-test)#clamp tcp-mss wm3400-34710C8(config-fw-policy-test)#show context firewall-policy test no ip dos tcp-sequence-past-window no Resets values or disables firewall policy alg commands tcp-mss Limits the TCP MSS size to the MTU value of the inner protocol for tunneled packets
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 887 Related Commands dhcp-offer-convert firewall-policy Enables the conversion of broadcast DHCP offers to unicast Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dhcp-offer-convert Parameters None Example wm3400-34710C8(config-fw-policy-test)#dhcp-offer-convert wm3400-34710C8(config-fw-policy-test)#show context firewall-policy test no ip dos tcp-sequence-past-window dhcp-offer-convert Related Commands dns-snoop firewall-policy Sets the timeout for DNS snoop table entries no Resets values or disables firewall policy clamp commands no Resets values or disables firewall policy DHCP offer convert commands
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 888 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax dns-snoop entry-timeout <30-86400> Parameters dns-snoop entry-timeout <30-86400> Example wm3400-34710C8(config-fw-policy-test)#dns-snoop entry-timeout 35 wm3400-34710C8(config-fw-policy-te)#show context firewall-policy te no ip dos tcp-sequence-past-window dhcp-offer-convert dns-snoop entry-timeout 35 Related Commands firewall firewall-policy Enables a devices firewall entry-timeout <30-86400> Sets the timeout value for DNS entries from 30 - 86400 seconds no Resets values or disables firewall policy DNS snoop commands
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 889 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax firewall enable Parameters firewall enable Example wm3400-34710C8(config-fw-policy-default)#firewall enable wm3400-34710C8(config-fw-policy-default)# Related Commands flow firewall-policy Defines the session flow timeout for different packet types firewall enable Enables the wireless firewall no Disables a devices firewall
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 890 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax flow [dhcp|timeout] flow dhcp stateful flow timeout [icmp|other|tcp|udp] flow timeout [icmp|other] <1-32400> flow timeout udp <15-32400> flow timeout tcp [close-wait|reset|setup|stateless-fin-or-reset| stateless-general] <1-32400> flow timeout tcp established <15-32400> Parameters flow dhcp stateful flow timeout [icmp|other] <1-32400> flow timeout udp <15-32400> flow timeout tcp [close-wait|reset|setup|stateless-fin-or-reset| stateless-general] <1-32400> dhcp Configures DHCP packet flow stateful Performs a stateful check on DHCP packets timeout Configures a packet timeout icmp Configures the timeout for ICMP packets other Configures the timeout for packets that are not ICPM, TCP, or UDP <1-32400> Configures the timeout from 1 - 32400 seconds timeout Configures a packet timeout udp Configures the timeout for UDP packets <15-32400> Configures the timeout from 15 - 32400 seconds timeout Configures a packet timeout
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 891 flow timeout tcp established <15-32400> Example wm3400-34710C8(config-rw-policy-test)#flow timeout udp 10000 wm3400-34710C8(config-rw-policy-test)#flow timeout icmp 16000 wm3400-34710C8(config-rw-policy-test)#flow timeout other 16000 wm3400-34710C8(config-rw-policy-test)#flow timeout tcp established 1500 wm3400-34710C8(config-rw-policy-test)#show context firewall-policy test no ip dos tcp-sequence-past-window flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert dns-snoop entry-timeout 35 Related Commands ip firewall-policy Configures Internet Protocol (IP) components tcp Configures the timeout for TCP packets close-wait Configures the closed TCP flow timeout reset Configures the reset TCP flow timeout setup Configures the opening TCP flow timeout stateless-fin-or-reset Configures the stateless TCP flow timeout created with the FIN or RESET packets stateless-general Configures the stateless TCP flow timeout <1-32400> Configures the timeout from 1 - 32400 seconds timeout Configures packet timeout tcp Configures the timeout for TCP packets established Configures the established TCP flow timeout <15-32400> Configures the timeout from 15 - 32400 seconds no Resets values or disables firewall policy flow commands
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 892 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip [dos|tcp] ip dos {[ascend|broadcast-multicast-icmp|chargen|fraggle|ftp-bounce| invalid-protocol|ip-ttl-zero|ipspoof|land|option-route|router-advt| router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp- intercept| tcp-max-incomplete|tcp-null-scan|tcp-post-syn|tcp-sequence-past- window| tcp-xmas-scan|tcphdrfrag|twinge|udp-short-hdr|winnuke]} ip tcp [adjust-mss|recreate-flow-on-out-of-state-syn|validate-icmp- unreachable| validate-rst-ack-number|validate-rst-seq-number|optimize- unnecessary-resends] ip dos {[ascend|broadcast-multicast-icmp|chargen|fraggle|ftp- bounce|invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router- advt|router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp- intercept|tcp-null-scan|tcp-post-scan|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag|twinge|udp-short-hdr|winnuke]} {[log-and-drop|log-only]} {log-level} {[<0- 7>|alerts|critical|debug|emergencies|errors|informational|notifications|war nigns]} ip dos {[ascend|broadcast-multicast-icmp|chargen|fraggle|ftp- bounce|invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router- advt|router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp- intercept|tcp-null-scan|tcp-post-scan|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag|twinge|udp-short-hdr|winnuke]} {drop-only} ip dos tcp-max-incomplete [high|low] <1-1000>
ip tcp adjust-mss <472-1460> ip tcp [optimize-unnecessary-resends| recreate-flow-on-out-of-state-syn|validate-icmp-unreachable| validate-rst-ack-number|validate-rst-seq-number]
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 893 Parameters ip dos {[ascend|broadcast-multicast-icmp|chargen|fraggle|ftp-bounce| invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router-advt| router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp-intercept| tcp-null-scan|tcp-post-scan|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag| twinge|udp-short-hdr|winnuke]} {[log-and-drop|log-only]} {log-level} {[<0- 7>|alerts|critical|debug|emergencies|errors|informational|notifications| warnigns]} dos Identifies IP events as DoS events ascend Enables an ASCEND DoS check. Ascend routers listen on UDP port 9 for packets from Ascend's Java Configurator. Sending a formatted packet to this port can cause an Ascend router to crash. broadcast-multicast-icmp Detects broadcast or multicast ICMP packets as an attack chargen The Character Generation Protocol (chargen) is an IP suite service primarily used for testing and debugging networks. It is also used as a source of generic payload for bandwidth and QoS measurements. fraggle A Fraggle DoS attack checks for UDP packets to or from port 7 or 19 ftp-bounce A FTP bounce attack is a MIM attack that enables an attacker to open a port on a different machine using FTP. FTP requires that when a connection is requested by a client on the FTP port (21), another connection must open between the server and the client. To confirm, the PORT command has the client specify an arbitrary destination machine and port for the data connection. This is exploited by the attacker to gain access to a device that may not be the originating client. invalid-protocol Enables a check for an invalid protocol number ip-ttl-zero Enables a check for the TCP/IP TTL field having a value of zero (0) ipsproof Enables a check for the IP spoofing DoS attack land A Local Area Network Denial (LAND) is a DoS attack where IP packets are spoofed and sent to a device where the source IP and destination IP of the packet are the target devices IP, and similarly, the source port and destination port are open ports on the same device. This causes the attacked device to reply to itself continuously. option-route Enables an IP Option Record Route DoS check router-advt This is an attack where a default route entry is added remotely to a device. This route entry is given preference, and thereby exposes an attack vector. router-solicit Router solicitation messages are sent to locate routers as a form of network scanning. This information can then be used to attack a device. smurf In this attack, a large number of ICMP echo packets are sent with a spoofed source address. This causes the device with the spoofed source address to be flooded with a large number of replies. snork This attack causes a remote Windows NT to consume 100% of the CPUs resources. This attack uses a UDP packtet with a destination port of 135 and a source port of 7, 9, or 135. This attack can also be exploited as a bandwidth consuming attack. tcp-bad-sequence A DoS attack that uses a specially crafted TCP packet to cause the targeted device to drop all subsequent network traffic for a specific TPC connection tcp-fin-scan A FIN scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcp-intercept Prevents TCP intercept attacks by using TCP SYN cookies
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 894 ip dos {[ascend|broadcast-multicast-icmp|chargen|fraggle|ftp-bounce| invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router-advt| router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp-intercept| tcp-null-scan|tcp-post-scan|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag| twinge|udp-short-hdr|winnuke]} {drop-only} tcp-null-scan A TCP null scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports. tcp-post-syn Enables TCP post SYN DoS attacks tcp-sequence-past-window Enables a TCP SEQUENCE PAST WINDOW DoS attack check. Disable this check to work around a bug in Windows XP's TCP stack which sends data past the window when conducting a selective ACK. tcp-xmas-scan A TCP XMAS scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcphdrfrag A DoS attack where the TCP header spans IP fragments twinge A twinge attack is a flood of false ICMP packets to try and slow down a system udp-short-hdr Enables the identification of truncated UDP headers and UDP header length fields winnuke This DoS attack is specific to Windows 95 and Windows NT, causing devices to crash with a blue screen log-and-drop Logs the event and drops the packet log-only Logs the event only, the packet is not dropped log-level Configures the log level <0-7> Sets the numeric logging level alerts Numerical severity 1. Indicates a condition where immediate action is required critical Numerical severity 2. Indicates a critical condition debugging Numerical severity 7. Debugging messages emergencies Numerical severity 0. System is unusable errors Numerical severity 3. Indicates an error condition informational Numerical severity 6. Indicates a informational condition notification Numerical severity 5. Indicates a normal but significant condition warnings Numerical severity 4. Indicates a warning condition dos Identifies IP events as DoS events ascend Enables an ASCEND DoS check. Ascend routers listen on UDP port 9 for packets from Ascend's Java Configurator. Sending a formatted packet to this port can cause an Ascend router to crash. broacast-multicast-icmp Detects broadcast or multicast ICMP packets as an attack chargen The Character Generation Protocol (chargen) is an IP suite service primarily used for testing and debugging networks. It is also used as a source of generic payload for bandwidth and QoS measurements. fraggle A Fraggle DoS attack checks for UDP packets to or from port 7 or 19 ftp-bounce A FTP bounce attack is a MIM attack that enables an attacker to open a port on a different machine using FTP. FTP requires that when a connection is requested by a client on the FTP port (21), another connection must open between the server and the client. To confirm, the PORT command has the client specify an arbitrary destination machine and port for the data connection. This is exploited by the attacker to gain access to a device that may not be the originating client.
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 895 ip dos tcp-max-incomplete [high|low] <1-1000> invalid-protocol Enables a check for invalid protocol number ip-ttl-zero Enables a check for the TCP/IP TTL field having a value of zero (0) ipsproof Enables a check for IP spoofing DoS attack land A Local Area Network Denial (LAND) is a DoS attack where IP packets are spoofed and sent to a device where the source IP and destination IP of the packet are the target devices IP, and similarly, the source port and destination port are open ports on the same device. This causes the attacked device to reply to itself continuously. option-route Enables an IP Option Record Route DoS check router-advt This is an attack where a default route entry is added remotely to a device. This route entry is given preference, and thereby exposes an attack vector. router-solicit Router solicitation messages are sent to locate routers as a form of network scanning. This information can then be used to attack a device. smurf In this attack a large number of ICMP echo packets are sent with a spoofed source address. This causes the device with the spoofed source address to be flooded with a large number of replies. snork This attack causes a remote Windows NT to consume 100% of the CPUs resources. This attack uses a UDP packtet with a destination port of 135 and a source port of 7, 9, or 135. This attack can also be exploited as a bandwidth consuming attack. tcp-bad-sequence A DoS attack that uses a specially crafted TCP packet to cause the targeted device to drop all subsequent network traffic for a specific TPC connection tcp-fin-scan A FIN scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcp-intercept Prevents TCP intercept attacks by using TCP SYN cookies tcp-null-scan A TCP null scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcp-post-syn Enables a TCP post SYN DoS attack tcp-sequence-past-window Enables a TCP SEQUENCE PAST WINDOW DoS attack check. Disable this check to work around a bug in Windows XP's TCP stack which sends data past the window when conducting a selective ACK. tcp-xmas-scan A TCP XMAS scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcphdrfrag A DoS attack where the TCP header spans IP fragments twinge A twinge attack is a flood of false ICMP packets to try and slow down a system udp-short-hdr Enables the identification of truncated UDP headers and UDP header length fields winnuke This DoS attack is specific to Windows 95 and Windows NT, causing devices to crash with a blue screen drop-only Drops a packet without logging dos Identifies IP events as DoS events tcp-max-incomplete Sets the limits for the maximum number of incomplete TCP connections high Sets the upper limit for the maximum number of incomplete TCP connections low Sets the lower limit for the maximum number of incomplete TCP connections <1-1000> Sets the limit in the range of 1 - 1000 connections
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 896 ip tcp adjust-mss <472-1460> ip tcp [optimize-unnecessary-resends|recreate-flow-on-out-of-state- syn|validate-icmp-unreachable|validate-rst-ack-number|validate-rst-seq- number] Example wm3400-34710C8(config-rw-policy-test)#ip dhcp fraggle drop-only wm3400-34710C8(config-rw-policy-test)#ip dhcp tcp-max-incomplete high 600 wm3400-34710C8(config-rw-policy-test)#ip dhcp tcp-max-incomplete low 60 wm3400-34710C8(config-rw-policy-test)#show context firewall-policy test ip dos fraggle drop-only no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert dns-snoop entry-timeout 35 Related Commands ip-mac firewall-policy Defines an action based on the device IP MAC table, and also detects conflicts between IP addresses and MAC addresses tcp Identifies and configures TCP events and configuration items adjust-mss Adjusts the TCP Maximum Segment Size (MSS) <472-1460> Sets the TCP MSS value from 472 - 1460 tcp Identifies and configures TCP events and configuration items optimize-unnecessary-resends Enables the validation of unnecessary of TCP packets recreate-flow-on-out-of-state- sync Allows a TCP SYN packet to delete an old flow in TCP_FIN_FIN_STATE, and TCP_CLOSED_STATE states and create a new flow validate-icpm-unreachable Enables the validation of the sequence number in ICMP unreachable error packets which abort an established TCP flow validate-rst-ack-number Enables the validation of acknowledgement number in RST packets which abort a TCP flow validate-rst-seq-number Enables the validation of the sequence number in RST packets which abort an established TCP flow no Resets values or disables firewall policy IP commands
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 897 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip-mac [conflict|routing] ip-mac conflict drop-only ip-mac conflict [log-and-drop|log-only] log-level [<0- 7>|alerts|critical|debug| emergencies|errors|informational|notifications|warnings] ip-mac routing conflict drop-only ip-mac routing [log-and-drop|log-only] log-level [<0- 7>|alerts|critical|debug| emergencies|errors|informational|notifications|warnings] Parameters ip-mac conflict drop-only ip-mac conflict [log-and-drop|log-only] log-level [<0- 7>|alerts|critical|debug| emergencies|errors|informational|notifications|warnings] conflict Action performed when a conflict exists between the IP address and MAC address drop-only Drops a packet without logging conflict Action performed when a conflict exists between the IP address and MAC address log-and-drop Logs the event and drops the packet log-only Logs the event only, the packet is not dropped log-level Configures the log level <0-7> Sets the numeric logging level alerts Numerical severity 1. Indicates a condition where immediate action is required critical Numerical severity 2. Indicates a critical condition debugging Numerical severity 7. Debugging messages emergencies Numerical severity 0. System is unusable
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 898 ip-mac routing conflict drop-only ip-mac routing [log-and-drop|log-only] log-level [<0- 7>|alerts|critical|debug| emergencies|errors|informational|notifications|warnings] Example wm3400-34710C8(config-rw-policy-test)#ip-mac conflict drop-only wm3400-34710C8(config-rw-policy-test)#ip-mac routing conflict log-and-drop log-level notifications wm3400-34710C8(config-rw-policy-test)#show context firewall-policy test ip dos fraggle drop-only no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 ip-mac conflict drop-only ip-mac routing conflict log-and-drop log-level notifications flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert errors Numerical severity 3. Indicates an error condition informational Numerical severity 6. Indicates a informational condition notification Numerical severity 5. Indicates a normal but significant condition warnings Numerical severity 4. Indicates a warning condition routing Defines a routing table based action conflict Action performed when a conflict exists in the routing table drop-only Drops a packet without logging routing Defines a routing table based action conflict Action performed when a conflict exists in the routing table log-and-drop Logs the event and drops the packet log-only Logs the event only, the packet is not dropped log-level Configures the log level to log this event under <0-7> Sets the numeric logging level alerts Numerical severity 1. Indicates a condition where immediate action is required critical Numerical severity 2. Indicates a critical condition debugging Numerical severity 7. Debugging messages emergencies Numerical severity 0. System is unusable errors Numerical severity 3. Indicates an error condition informational Numerical severity 6. Indicates a informational condition notification Numerical severity 5. Indicates a normal but significant condition warnings Numerical severity 4. Indicates a warning condition
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 899 dns-snoop entry-timeout 35 Related Commands logging firewall-policy Configures enhanced firewall logging Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax logging [icmp-packet-drop|malformed-packet-drop|verbose] logging verbose logging [icmp-packet-drop|malformed-packet-drop] [all|rate-limited] Parameters logging verbose logging [icmp-packet-drop|malformed-packet-drop] [all|rate-limited] no Resets values or disables IP MAC commands logging Configures enhanced firewall logging verbose Enables verbose logging logging Configures enhanced firewall logging icmp-packet-drop Drops ICMP packets that do not pass sanity checks malformed-packet-drop Drops raw IP packets that do not pass sanity checks all Logs all messages rate-limited Sets the rate limit for log messages to one message every 20 seconds
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 900 Example wm3400-34710C8(config-rw-policy-test)#logging verbose wm3400-34710C8(config-rw-policy-test)#logging icmp-packet-drop rate-limited wm3400-34710C8(config-rw-policy-test)#logging malformed-packet-drop all wm3400-34710C8(config-rw-policy-test)#show context firewall-policy test ip dos fraggle drop-only no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 ip-mac conflict drop-only ip-mac routing conflict log-and-drop log-level notifications flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert logging icmp-packet-drop rate-limited logging malformed-packet-drop all logging verbose dns-snoop entry-timeout 35 Related Commands no firewall-policy Negates a command or sets the default for firewall policy commands Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [alg|clamp|dhcp-offer-convert|dns-snooping|firewall|flow|ip|ip- mac|logging| no Resets values or disables IP MAC commands
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 901 proxy-arp|stateful-packet-inspection-l2|storm-control|virtual- defragmentation] no [dhcp-offer-convert|proxy-arp|stateful-packet-inspection-l2] no alg [dns|ftp|sip|tftp] no clamp tcp-mss no dns-snooping entry-timeout no firewall enable no flow dhcp stateful no flow timeout [icmp|other|udp] no flow timeout tcp [closed-wait|established|reset|setup|stateless-fin-or- reset| stateless-general] no ip dos [ascend|broadcast-multicast-icmp|chargen|fraggle|ftp-bounce| invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router-advt| router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp-intercept| tcp-null-scan|tcp-post-syn|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag| twinge|udp-short-hdr|winnuke] no ip tcp [adjust-mss|optimize-unnecessary-resends| recreate-flow-on-out-of-state-syn|validate-icmp-unreachable| validate-rst-ack-number|validate-rst-seq-number] no ip-mac conflict no ip-mac routing conflict no logging [icmp-packet-drop|verbose|malformed-packet-drop] storm-control [arp|broadcast|multicast|unicast] {[fe <1-4>|ge <1-8>|log| port-channel <1-8>|up1|wlan <WLAN>]} no virtual-defragmentation {[maximum-fragments-per-datagram| minimum-first-fragment-length|maximum-defragmentation-per-host]} Parameters no [dhcp-offer-convert|proxy-arp|stateful-packet-inspection-l2] no alg [dns|ftp|sip|tftp] no dhcp-offer-convert Disables the conversion of broadcast DHCP offers to unicast no proxy-arp Disables the generation of ARP responses on behalf of other devices no stateful-packet-inspection-l2 Disables layer 2 stateful packet inspection no alg Disables preconfigured algorithms (dns, ftp, sip, and tftp) dns Disables the DNS algorithm
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 902 no clamp tcp-mss no dns-snooping entry-timeout no firewall enable no flow dhcp stateful no flow timeout [icmp|other|udp] no flow timeout tcp [closed-wait|established|reset|setup|stateless-fin-or- reset|stateless-general] no ip dos [ascend|broadcast-multicast-icmp|chargen|fraggle|ftp-bounce| invalid-protocol|ip-ttl-zero|ipsproof|land|option-route|router-advt| router-solicit|smurf|snork|tcp-bad-sequence|tcp-fin-scan|tcp-intercept| ftp Disables the FTP algorithm sip Disables the SIP algorithm tftp Disables the TFTP algorithm no clamp tcp-mss Disables limiting the TCP MSS to the size of the MTU of the inner protocol for a tunneled packet no dns Disables DNS snooping entry-timeout Disables DNS snoop table entry timeout no firewall enable Disables a devices firewalls no flow Disables firewall flows dhcp stateful Disables DHCP stateful flow no flow Disables firewall flow timeout Disables the timeout for following packet types: icmp Disables ICMP packet timeout others Disables the timeout for packets that are not TCP, ICMP, or UDP udp Disables UDP packet timeout no flow Disables firewall flows timeout Disables the timeout for the following packet types: tcp Disables TCP packet timeout close-wait Disables the timeout for TCP flows in close wait status established Disables the timeout for TCP flows in established status reset Disables the timeout for TCP flows in reset status setup Disables the timeout for TCP flows in setup status stateless-fin-or-reset Disables the timeout for TCP flows in stateless FIN or RST status stateless-general Disables the timeout for TCP flows in general stateless states
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 903 tcp-null-scan|tcp-post-syn|tcp-sequence-past-window|tcp-xmas- scan|tcphdrfrag| twinge|udp-short-hdr|winnuke] no ip Disables IP events dos Disables IP DoS events ascend Disables an ASCEND DoS check Ascend routers listen on UDP port 9 for packets from Ascend's Java Configurator. Sending a formatted packet to this port can cause an Ascend router to crash. broacast-multicast-icmp Disables the detection of broadcast or multicast ICMP packets as an attack chargen Disables the chargen service The Character Generation Protocol (chargen) is an IP suite service primarily used for testing and debugging networks. It is also used as a generic payload for bandwidth and QoS measurements. fraggle Disables checking for Fraggle DoS attacks. This checks for UDP packets to or from port 7 or 19 ftp-bounce Disables FTP bounce attack checks A FTP bounce attack is a MIM attack that enables an attacker to open a port on a different machine using FTP. FTP requires that when a connection is requested by a client on the FTP port (21), another connection must open between the server and the client. To confirm, the PORT command has the client specify an arbitrary destination machine and port for the data connection. This is exploited by the attacker to gain access to a device that may not be the originating client. invalid-protocol Disables a check for invalid protocol number ip-ttl-zero Disables a check for the TCP/IP TTL field with a value of Zero (0) ipsproof Disables IP spoofing DoS attack checks land Disables LAND attack checks Local Area Network Denial (LAND) is a DoS attack where IP packets are spoofed and sent to a device where the source IP and destination IP of the packet are the target devices IP, and similarly, the source port and destination port are open ports on the same device. This causes the attacked device to reply to itself continuously. option-route Disables an IP Option Record Route DoS check router-advt Disables router-advt attack checks This is an attack where a default route entry is added remotely to a device. This route entry is given preference, and thereby exposes a vector of attacks. router-solicit Disables router-solicit attack checks Router solicitation messages are sent to locate routers as a form of network scanning. This information can then be used to attack a device. smurf Disables smurf attack checks In this attack a large number of ICMP echo packets are sent with a spoofed source address. This causes the device with the spoofed source address to be flooded with a large number of replies. snork Disables snork attack checks This attack causes a remote Windows NT to consume 100% of the CPUs resources. This attack uses a UDP packtet with a destination port of 135 and a source port of 7, 9, or 135. This attack can also be exploited as a bandwidth consuming attack.
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 904 no ip tcp [adjust-mss|optimize-unnecessary-resends| recreate-flow-on-out-of-state-syn|validate-icmp-unreachable| validate-rst-ack-number|validate-rst-seq-number] no ip-mac conflict tcp-bad-sequence Disables tcp-bad-sequence checks This DoS attack uses a specially crafted TCP packet to cause the targeted device to drop all subsequent network of a specific TPC connection. Disables tcp-bad-sequence check. tcp-fin-scan Disables TCP FIN scan checks A FIN scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcp-intercept Disables TCP intercept attack checks Prevents TCP intercept attacks by using TCP SYN cookies tcp-null-scan Disables TCP Null scan checks A TCP null scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcp-post-syn Disables TCP post SYN DoS attack checks tcp-sequence-past-window Disables TCP SEQUENCE PAST WINDOW DoS attack checks Disable this check to work around a bug in Windows XP's TCP stack which sends data past the window when conducting a selective ACK. tcp-xmas-scan Disables TCP XMAS scan checks A TCP XMAS scan finds services on ports. A closed port returns a RST. This allows the attacker to identify open ports tcphdrfrag Disables TCP header checks A DoS attack where the TCP header spans IP fragments twinge Disables twinge attack checks A twinge attack is a flood of false ICMP packets to try and slow down a system udp-short-hdr Disables UDP short header checks Enables the identification of truncated UDP headers and UDP header length fields winnuke Disables Winnuke checks This DoS attack is specific to Windows 95 and Windows NT, causing devices to crash with a blue screen no ip Disables IP DoS events tcp Identifies and disables TCP events and configuration items adjust-mss Disables the adjust MSS configuration optimize-unnecessary-resends Disables the validation of unnecessary TCP packets recreate-flow-on-out-of-state- sync Disallows a TCP SYN packet to delete an old flow in TCP_FIN_FIN_STATE, and TCP_CLOSED_STATE states and create a new flow validate-icpm-unreachable Disables the sequence number validation in ICMP unreachable error packets validate-rst-ack-number Disables the acknowledgement number validation in RST packets validate-rst-seq-number Disables the sequence number validation in RST packets no ip-mac Disables IP MAC configuration
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 905 no ip-mac routing conflict no logging [icmp-packet-drop|verbose|malformed-packet-drop] no storm-control [arp|broadcast|multicast|unicast] {[fe <1-4>|ge <1-8>|log| port-channel <1-8>|up1|wlan <WLAN>]} no virtual-defragmentation {[maximum-fragments-per-datagram| minimum-first-fragment-length|maximum-defragmentation-per-host]} conflict Disables the action performed when a conflict exists between the IP address and MAC address no ip-mac Disables IP MAC configuration routing Configures a routing table based action conflict Disables the action performed when a conflict exists in the routing table no logging Disables enhanced firewall logging icmp-packet-drop Disables dropping of ICMP packets that do not pass sanity checks malformed-packet-drop Disables dropping of raw IP packets that do not pass sanity checks verbose Disables verbose logging no storm-control Disables storm control arp Disables storm control for ARP packets broadcast Disables storm control or broadcast packets multicast Disables storm control for multicast packets unicast Disables storm control for unicast packets fe <1-4> Disables the FastEthernet port <1-4> Sets the FastEthernet port ge <1-8> Disables the Gigabit Ethernet port <1-8> Sets the GigabitEthernet port log Disables storm control logging port-channel <1-8> Disables the port channel. <1-8> Sets the port channel port up1 Disables the uplink interface wlan <WLAN> Disables the WLAN <WLAN> Sets the WLAN ID no virtual-defragmentation Disables the virtual defragmentation of IPv4 packets maximum-defragmentation-per- host <1-16384> Optional. Disables the maximum active IPv4 defragmentation per host maximum-fragments-per- datagram <2-8129> Optional. Disables the maximum IPv4 fragments per datagram minimum-first-fragment-length <8-1500> Optional. Disables the minimum length required for the first IPv4 fragment
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 906 Example wm3400-34710C8(config-fw-policy-test)#show context firewall-policy test ip dos fraggle drop-only no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 storm-control broadcast level 20000 ge 4 storm-control arp log warnings ip-mac conflict drop-only ip-mac routing conflict log-and-drop log-level notifications flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert logging icmp-packet-drop rate-limited logging malformed-packet-drop all logging verbose dns-snoop entry-timeout 35 wm3400-34710C8(config-fw-policy-test)#no ip dos fraggle wm3400-34710C8(config-fw-policy-test)#no storm-control arp log wm3400-34710C8(config-fw-policy-test)#no dhcp-offer-convert wm3400-34710C8(config-fw-policy-test)#no logging malformed-packet-drop wm3400-34710C8(config-fw-policy-test)#show context firewall-policy test no ip dos fraggle no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 storm-control broadcast level 20000 ge 4 storm-control arp log none ip-mac conflict drop-only ip-mac routing conflict log-and-drop log-level notifications flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 logging icmp-packet-drop rate-limited logging verbose dns-snoop entry-timeout 35
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 907 Related Commands proxy-arp firewall-policy Enables the generation of ARP responses on behalf of another device Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax proxy-arp Parameters None Example wm3400-34710C8(config-fw-policy-test)#proxy-arp wm3400-34710C8(config-fw-policy-test)# alg Configures algorithms used with a firewall policy clamp Limits the TCP MSS to the MTU value of the inner protocol for tunneled packets dhcp-offer-convert Enables the conversion of broadcast DHCP offer packets to unicast dns-snoop Configures the DNS snoop table entry timeout firewall Enables firewalls flow Configures firewall flows ip Configures IP settings ip-mac Defines actions based on the device IP MAC table logging Configures firewall logging proxy-arp Enables the generation of ARP responses on behalf of other devices stateful-packet-inspection-12 Enables layer 2 stateful packet inspection storm-control Configures storm control virtual-defragmentation Configures the virtual defragmentation of packets at the firewall level
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 908 Related Commands stateful-packet-inspection-12 firewall-policy Enables layer 2 firewall stateful packet inspection Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax stateful-packet-inspection-l2 Parameters None Example wm3400-34710C8(config-fw-policy-test)#stateful-packet-inspection-l2 wm3400-34710C8(config-fw-policy-test)# Related Commands storm-control firewall-policy Storm control limits multicast, unicast and broadcast frames accepted and forwarded by a device. Messages are logged based on their severity level no Resets values or disables proxy ARP commands no Resets values or disables layer 2 stateful packet inspection commands
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 909 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax storm-control [arp|broadcast|multicast|unicast] storm-control [arp|broadcast|multicast|unicast] [level|log] storm-control [arp|broadcast|multicast|unicast] level <1-1000000> [fe <1- 4>| ge <1-8>|port-channel <1-8>|up1|wlan <WLAN>] storm-control [arp|broadcast|multicast|unicast] log [<0-7>|alerts|critical| debugging|emergencies|errors|informational|none|notifications|warnings] Parameters storm-control [arp|broadcast|multicast|unicast] level <1-1000000> [fe <1- 4>| ge <1-8>|port-channel <1-8>|up1|wlan <WLAN>] arp Configures storm control for ARP packets broadcast Configures storm control for broadcast packets multicast Configures storm control for multicast packets unicast Configures storm control for unicast packets level <1-1000000> Configures the allowed number of packets received per second before storm control begins <1-1000000> Sets the number of packets received per second fe <1-4> Sets the FastEthernet port for storm control from 1 - 4 ge <1-8> Sets the GigabitEthernet port for storm control from 1 - 8 port-channel <1-8> Sets the port channel for storm control from 1- 8 up1 Sets the uplink interface wlan <WLAN> Configures the WLAN <WLAN> Sets the WLAN ID for the storm control configuration
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 910 storm-control [arp|bcast|multicast|unicast] log [<0-7>|alerts|critical| debugging|emergencies|errors|informational|none|notifications|warnings] Example wm3400-34710C8(config-fw-policy-test)#storm-control arp log warning wm3400-34710C8(config-fw-policy-test)#storm-control broadcast level 20000 ge 4 wm3400-34710C8(config-fw-policy-test)#show context firewall-policy test ip dos fraggle drop-only no ip dos tcp-sequence-past-window ip dos tcp-max-incomplete high 600 ip dos tcp-max-incomplete low 60 storm-control broadcast level 20000 ge 4 storm-control arp log warnings ip-mac conflict drop-only ip-mac routing conflict log-and-drop log-level notifications flow timeout icmp 16000 flow timeout udp 10000 flow timeout tcp established 1500 flow timeout other 16000 dhcp-offer-convert logging icmp-packet-drop rate-limited logging malformed-packet-drop all logging verbose dns-snoop entry-timeout 35 arp Configures storm control for ARP packets broadcast Configures storm control for broadcast packets multicast Configures storm control for multicast packets unicast Configures storm control for unicast packets log Configures the storm control log level for storm control events <0-7> Sets the numeric logging level from 0 - 7 alerts Numerical severity 1. Indicates a condition where immediate action is required critical Numerical severity 2. Indicates a critical condition debugging Numerical severity 7. Debugging messages emergencies Numerical severity 0. System is unusable errors Numerical severity 3. Indicates an error condition informational Numerical severity 6. Indicates a informational condition none Disables storm control logging notification Numerical severity 5. Indicates a normal but significant condition warnings Numerical severity 4. Indicates a warning condition
firewall-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 911 Related Commands virtual-defragmentation firewall-policy Enables the virtual defragmentation of IPv4 packets. This parameter is required for optimal firewall functionality. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax virtual-defragmentation {maximum-defragmentation-per-host <1-16384>| maximum-fragments-per-datagram <2-8129>|minimum-first-fragment- length <8-1500>} Parameters virtual-defragmentation {maximum-defragmentation-per-host <1-16384>| maximum-fragments-per-datagram <2-8129>|minimum-first-fragment-length <8- 1500>} Example wm3400-34710C8(config-fw-policy-test)#virtual-defragmentation maximum- fragments-per-datagram 10 wm3400-34710C8(config-fw-policy-test)#virtual-defragmentation minimum- first-fragment-length 100 no Resets values or disables storm control commands maximum-defragmentation-per- host <1-16384> Optional. Defines the maximum active IPv4 defragmentation per host <1-16384> Sets a value from 1 - 16384 maximum-fragments-per- datagram <2-8129> Optional. Defines the maximum IPv4 fragments per datagram <2-8129> Sets a value from 2 - 8129 minimum-first-fragment-length <8-1500> Optional. Defines the minimum length required for the first IPv4 fragment <8-1500> Sets a value from 8 - 1500
Chapter 15: Firewall Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 912 wm3400-34710C8(config-fw-policy-test)# Related Commands no Resets values or disables virtual defragmentation commands
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 913 C H A P T E R 16 MINT Policy This chapter summarizes MiNT policy commands within the CLI structure. All communication using the MiNT transport layer can be optionally secured. This includes confidentiality, integrity and authentication of all communications. In addition, a device can be configured to communicate over MiNT with other devices authorized by an administrator. Use the (config) instance to configure mint-policy related configuration commands. To navigate to the MiNT policy instance, use the following commands: wm3400-34710C8(config)#mint-policy global-default wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#? wm3400-34710C8(config-mint-policy-global-default)#? Mint Policy Mode commands: level Mint routing level mtu Configure the global Mint MTU no Negate a command or set its defaults udp Configure mint UDP/IP encapsulation clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-mint-policy-global-default)#
Chapter 16: MINT Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 914 mint-policy The following table summarizes MiNT policy commands level mint-policy Configures the global MiNT routing level Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax level 2 area-id <1-16777215> Command Description Reference level Configures MiNT routing level page 16-914 mtu Configures the global MiNT MTU page 16-915 no Negates a command or sets its default value page 16-917 udp Configures MiNT UDP/IP encapsulation parameters page 16-916 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
mint-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 915 Parameters level 2 area-id <1-16777215> Example wm3400-34710C8(config-mint-policy-global-default)#level 2 area-id 2000 wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#show context mint-policy global-default level 2 area-id 2000 wm3400-34710C8(config-mint-policy-global-default)# Related Commands mtu mint-policy Configures global MiNT Multiple Transmission Unit (MTU). Use this command to specify the maximum packet size, in bytes, for MiNT routing. The higher the MTU values, the greater the network efficiency. The user data per packet increases, while protocol overheads, such as headers or underlying per-packet delays remain the same. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mtu <900-1500> level 2 Configures level 2 inter site MiNT routing area-id <1-16777215> Configures the routing area identifier <1-1677215> Specify a value from 1 - 16777215. no Disables level 2 MiNT routing of packets (disables inter site routing of packets)
Chapter 16: MINT Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 916 Parameters mtu <900-1500> Example wm3400-34710C8(config-mint-policy-global-default)#mtu 1000 wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#mtu 1000 wm3400-34710C8(config-mint-policy-global-default)#show context mint-policy global-default mtu 996 level 2 area-id 2 wm3400-34710C8(config-mint-policy-global-default)# Related Commands udp mint-policy Configures MiNT UDP/IP encapsulation parameters. Use this command to configure the default UDP port used for MiNT control packet encapsulation. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax udp port <2-65534> <900-1500> Specifies the maximum packet size from 900 - 1500 bytes The maximum packet size specified is rounded down to a value using the following formula: 4 + a multiple of 8. no Reverts the configured MiNT MTU value to its default Negates the configured maximum packet size for MiNT routing
mint-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 917 Parameters udp port <2-65534> Example wm3400-34710C8(config-mint-policy-global-default)#udp port 1024 wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#show context mint-policy global-default udp port 1024 mtu 996 level 2 area-id 2000 wm3400-34710C8(config-mint-policy-global-default)# Related Commands no mint-policy Negates a command or reverts values to their default. When used in the config MiNT policy mode, the no command resets or reverts the following global MiNT policy parameters: routing level, MTU, and UDP or IP encapsulation settings. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [level|mtu|udp no level 2 area-id port <2-65534> Configures default UDP port used for MiNT control packet encapsulation <2-65534> Enter a value from 2 - 65534. The specified value becomes the default UDP port. The value must be an even number, since data packets use the control port +1. no Reverts MiNT UDP/IP encapsulation to its default
Chapter 16: MINT Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 918 no mtu no udp port <LINE-SINK>] Parameters no level 2 area-id no mtu no udp port <LINE-SINK> Example The Mint Policy configured parameters before using the no command: wm3400-34710C8(config-mint-policy-global-default)#show context mint-policy global-default udp port 1024 mtu 996 level 2 area-id 2000 wm3400-34710C8(config-mint-policy-global-default)# The no command is used to negate the configured MiNT Policy settings. wm3400-34710C8(config-mint-policy-global-default)#no level 2 area-id wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#no mtu wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#no udp port wm3400-34710C8(config-mint-policy-global-default)# wm3400-34710C8(config-mint-policy-global-default)#show context mint-policy global-default wm3400-34710C8(config-mint-policy-global-default)# Related Commands no level 2 Disables level 2 MiNT routing area identifier Negates the area identifier no mtu Reverts the configured MiNT MTU value to its default no udp Resets UDP/IP encapsulation parameters to its default port <LINE-SINK> Uses default UDP port for MiNT encapsulation level Configures global MiNT routing level mtu Configures global MiNT MTU
mint-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 919 udp Configures MiNT UDP/IP encapsulation parameters
Chapter 16: MINT Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 920
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 921 C H A P T E R 17 Management Policy This chapter summarizes management policy commands within the CLI structure. A management policy contains configuration elements for managing a device, such as access control, SNMP, admin user credentials, and roles. Use the (config) instance to configure management policy related configuration commands. To navigate to the config management policy instance, use the following commands: wm3400-34710C8(config)#management-policy <POLICY-NAME> wm3400-34710C8(config)#management-policy default To commit a management-policy, at least one admin user account must always be present in the management-policy: wm3400-34710C8(config-management-policy-default)#user superuser password 1 extreme123 wm3400-34710C8(config-management-policy-default)#commit wm3400-34710C8(config-management-policy-default)# wm3400-34710C8(config-management-policy-default)#? Management Mode commands: aaa-login Set authentication for logins banner Define a login banner ftp Enable FTP server http Hyper Text Terminal Protocol (HTTP) https Secure HTTP idle-session-timeout Configure idle timeout for a configuration session (UI or mapsh) no Negate a command or set its defaults restrict-access Restrict management access to the device snmp-server SNMP ssh Enable ssh telnet Enable telnet user Add a user account clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 922 end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-management-policy-default)# management-policy The following table summarizes management policy commands aaa-login management-policy Command Description Reference aaa-login Sets authentication for logins page 17-922 banner Defines a login banner name page 17-924 ftp Enables a FTP server page 17-925 http Enables a HTTP server page 17-927 https Enables a secure HTTPS server page 17-928 idle-session-timeout Sets the interval after which a session is terminated page 17-929 no Negates a command or sets its default page 17-930 restrict-access Restricts management access to a set of hosts or subnets page 17-933 snmp-server Sets the SNMP server parameters page 17-936 ssh Enables SSH page 17-939 telnet Enables Telnet page 17-940 user Creates a new user account page 17-942 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 923 Specifies the Authentication, Authorization and Accounting (AAA) authentication mode used with this management policy. The different modes are: local authentication or external RADIUS server authentication. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax aaa-login [local|radius|tacacs] aaa-login local aaa-login radius [external|fallback|policy] aaa-login radius [external|fallback] aaa-login radius policy <AAA-POLICY-NAME> aaa-login tacacs [accounting|authentication|authorization|fallback|policy] aaa-login tacacs [accounting|authentication|authorization|fallback| policy <AAA-TACACS-POLICY-NAME>] Parameters aaa-login local aaa-login radius [external|fallback|policy <AAA-POLICY-NAME>] local Sets local as the preferred authentication mode. Local authentication uses the local username database to authenticate a user. radius Configures RADIUS server parameters external Configures external RADIUS server as the preferred authentication mode fallback Configures RADIUS server authentication as the primary authentication mode. When RADIUS server authentication fails, the system uses local authentication. This command configures local authentication as a backup mode. policy <AAA-POLICY-NAME> Uses a specified AAA policy <AAA-POLICY-NAME> Sets the name of the AAA policy. The AAA policy determines if a client is granted access to the network
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 924 aaa-login tacacs [accounting|authentication|authorization|fallback| policy <AAA-TACACS-POLICY-NAME>] Usage Guidelines Use AAA login to determine whether management user authentication must be performed against a local user database or an external RADIUS server. Example wm3400-34710C8(config-management-policy-test)#aaa-login radius external wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#aaa-login radius policy test wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server no ssh aaa-login radius external aaa-login radius policy test wm3400-34710C8(config-management-policy-test)# banner management-policy Configures the login banner message. Use this command to display messages to users as they as login. tacacs Configures Terminal Access Control Access-Control System (TACACS) server parameters accounting Configures TACACS accounting authentication Configures TACACS authentication authorization Configures TACACS authorization fallback Configures TACACS as the primary authentication mode. When TACACS authentication fails, the system uses local authentication. This command configures local authentication as a backup mode. policy <AAA-TACACS-POLICY- NAME> Uses a specified AAA TACACS policy <AAA-TACACS-POLICY-NAME> Sets the name of the TACACS policy
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 925 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax banner motd <LINE> Parameters banner motd <LINE> Example wm3400-34710C8(config-management-policy-test)#banner motd Have a Good Day wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server no ssh aaa-login radius external aaa-login radius policy test banner motd Have a Good Day wm3400-34710C8(config-management-policy-test)# Related Commands ftp management-policy Enables File Transfer Protocol (FTP) on this management policy motd <LINE> Sets the message of the day (motd) banner <LINE> Defines the message string no Removes the motd banner
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 926 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ftp {password|rootdir|username} ftp {password [1 <ENCRYPTED-PASSWORD>|<PASSWORD>]} ftp {rootdir [<DIR>]} ftp {username [<USERNAME>] password [1 <ENCRYPTED-PASSWORD>|<PASSWORD>] [rootdir <DIR>]} Parameters ftp {password [1 <ENCRYPTED-PASSWORD>|<PASSWORD>]} ftp {rootdir [<DIR>]} ftp {username [<USERNAME>] password [1 <ENCRYPTED-PASSWORD>|<PASSWORD>] [rootdir <DIR>]} ftp password Optional. Configures the FTP server password 1 <ENCRYPTED- PASSWORD> Configures an encrypted password <ENCRYPTED-PASSWORD> Sets the password <PASSWORD> Configures a clear text password ftp rootdir <DIR> Optional. Configures the root directory for FTP logins <DIR> Sets the root directory path ftp username <USERNAME> Optional. Configures new user account on the FTP server. The FTP user file lists users with FTP server access. <USERNAME> Sets the username password 1 <ENCRYPTED- PASSWORD> rootdir <DIR> Configures an encrypted password <ENCRYPTED-PASSWORD> Sets the password After specifying the password, configure the FTP root directory. rootdir Configures the root directory for FTP logins <DIR> Sets the root directory path
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 927 Usage Guidelines The string size of encrypted password (option 1, Password is encrypted with a SHA1 algorithm) must be exactly 40 characters. Example wm3400-34710C8(config-management-policy-test)#ftp password 1 extreme@123 wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#ftp rootdir dir wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#ftp username superuser password 1 word rootdir dir wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server ftp username root password 1 word rootdir dir user superuser password 1 4e03aaf1065294ba86d19da984347e38dfbaa9955335dc354748cb4f9a16e0a9 wm3400-34710C8(config-management-policy-test)# Related Commands http management-policy Enables the Hyper Text Transport Protocol (HTTP) server <PASSWORD> rootdir <DIR> Configures a clear text password After specifying the password, configure the FTP root directory. rootdir Configures the root directory for FTP logins <DIR> Sets the root directory path no Disables FTP and its settings, such as the server password, root directory, and users
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 928 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax http <HTTP-SERVER> Parameters http <HTTP-SERVER> Example wm3400-34710C8(config-management-policy-test)#http server wm3400-34710C8(config-management-policy-test)# Related Commands https management-policy Enables the secure Hyper Text Transport Protocol Secure (HTTPS) server http <HTTP-SERVER> Enables HTTP on this management policy <HTTP-SERVER> Sets the HTTP server name no Disables the HTTP server
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 929 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax https <HTTPS-SERVER> Parameters https <HTTPS-SERVER> Example wm3400-34710C8(config-management-policy-test)#https server wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server https server ftp username ftpuser password 1 aa91489995daff7b1363f37967c5104fe5952cae4936f902e653fccf81e8bb68 rootdir dir aaa-login radius external aaa-login radius policy test banner motd "Have a Good Day" wm3400-34710C8(config-management-policy-test)# Related Commands idle-session-timeout management-policy https <HTTPS-SERVER> Enables HTTPS on this management policy <HTTPS-SERVER> Sets the HHTPS server name no Disables the HTTPS server
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 930 Configures a sessions idle timeout. After the timeout period has been exceeded, the session is automatically terminated. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax idle-session-timeout <0-1440> Parameters idle-session-timeout <0-1440> Example wm3400-34710C8(config-management-policy-test)#idle-session-timeout 30 wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server https server aaa-login radius external aaa-login radius policy test idle-session-timeout 30 banner motd Have a Good Day wm3400-34710C8(config-management-policy-test)# Related Commands no management-policy <0-1440> Sets the interval after which a configuration session is timed out. Specify a value from 0 - 1440 minutes. Zero (0) indicates the session is never terminated. no Disables idle session timeout period
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 931 Negates a command or reverts values to their default. When used in the config management policy mode, the no command negates or reverts management policy parameters. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [aaa-login|banner|ftp|http|https|idle-session-timeout|restrict-access| snmp-server|ssh|telnet|user|service] no aaa-login tacacs [accounting|authorization|policy] no banner motd no ftp {password|rootdir} no [http|hhtps] server no [idle-session-timeout|restrict-action] no snmp-server [community|enable|host|manager|user] no snmp-server [community <WORD>|enable [throttle|traps]| host <IP> port <1-65535>|manager [all|v2|v3]|max-pending-requests| user [snmpmanager|snmpoperator|snmptrap] no [ssh {port|use-key}|telnet|user <USERNAME>] no service prompt crash-info Parameters no aaa-login tacacs [accounting|authorization|policy] no aaa-login Disables or reverts user authorization parameters tacacs Disables TACACS server parameters accounting Disables TACACS accounting authorization Disables TACACS authorization policy Disables a TACACS policy
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 932 no banner motd] no ftp {password|rootdir} no [http|hhtps] server no [idle-session-timeout|restrict-action] no snmp-server [community <WORD>|enable [throttle|traps]| host <IP> port <1-65535>|manager [all|v2|v3]|max-pending-requests| user [snmpmanager|snmpoperator|snmptrap] no [ssh {port|use-key}|telnet|user <USERNAME>] no banner motd Removes the motd banner no ftp Reverts to default FTP server settings password Optional. Reverts to default FTP password rootdir Optional. Reverts to default FTP root directory no http Disables the HTTP server no https Disables the HTTPS server no idle-session-timeout Disables session timeout period no restrict-session Removes management access restrictions placed on a device no snmp-server Disables the SNMP server parameters community <WORD> Disables SNMP server access to a community <WORD> Specify the name of the community. enable [throttle|traps] Disables SNMP traps and throttle host <IP> port <1-65535> Removes SNMP trap recipient (host) details <IP> Enter the IP address of the host (the trap recipient) port <1-65535> Disables the port for sending SNMP traps manager [all|v2|v3] Disables SNMP manager max-pending-requests Resets the maximum pending requests to default user [snmpmanager| snmpoperator|snmptrap] Removes SNMPv3 user snmpmanager Removes the SNMP manager snmpoperator Removes the SNMP operator snmptrap Removes the SNMP trap user no ssh {port|use-key} Disables secure shell access port Optional. Resets SSH port to factory default use-key Optional. Resets RSA key to factory default no telnet Disables Telnet no user <USERNAME> Deletes a user account <USERNAME> Specify the username of the account.
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 933 no service prompt crash-info] Example wm3400-34710C8(config-management-policy-test)#no banner motd wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#no idle-session-timeout wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server https server no ssh aaa-login radius external aaa-login radius policy test idle-session-timeout 0 wm3400-34710C8(config-management-policy-test)# Related Commands restrict-access management-policy Restricts management access to a set of hosts or subnets no service Disables service commands prompt Disables CLI prompt settings crash-info Excludes asterisks (*) at the end of the prompt, if the device has crash files in flash:/crashinfo banner Configures the login motd banner ftp Configures the FTP server parameters http Enables HTTP https Enables HTPPS idle-session-timeout Configures a sessions idle timeout restrict-access Restricts management access to a set of hosts or subnets. Also enables the logging of access requests snmp-server Configures SNMP engine parameters ssh Enables SSH connection between client and server telnet Enables Telnet user Adds a new user account service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 934 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax restrict-access [host|ip-access-list|subnet] restrict-access host <IP> {<IP>|log|subnet} restrict-access host <IP> {log [all|denied-only]} restrict-access host <IP> {subnet [<IP/M>] {log [all|denied-only]}} restrict-access ip-access-list <IP-ACCESS-LIST> restrict-access subnet <IP/M> {<IP/M>|host|log} restrict-access subnet <IP/M> {log [all|denied-only]} restrict-access subnet <IP/M> {host [<IP>] {log [all|denied-only]}} Parameters restrict-access host <IP> {log [all|denied-only] restrict-access host <IP> {subnet [<IP/M>] {log [all|denied-only]}} host <IP> Restricts management access to a specified host. Uses the IP address of a host to filter access requests <IP> Specify the host IP address. log [all|denied-only] Configures a logging policy for access requests. Sets the log type generated for access requests all Logs all access requests, both denied and permitted denied-only Logs only denied access host <IP> Restricts management access to a specified host. Uses the IP address of a host to filter access requests <IP> Specify the host IP address. subnet <IP/M> Optional. Restricts access on a specified subnet. Uses a subnet IP address as a second filter option. <IP/M> Sets the subnet IP address in the A.B.C.D/M format
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 935 restrict-access ip-access-list <IP-ACCESS-LIST> restrict-access subnet <IP/M> {log [all|denied-only]} restrict-access subnet <IP/M> {host [<IP>] {log [all|denied-only]}} Example wm3400-34710C8(config-management-policy-test)#restrict-access host 172.16.10.2 log all wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#restrict-access subnet 172.16.10.20/24 host 172.16.10.3 log all wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#restrict-access host 172.16.10.4 log denied-only wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server no ssh log [all|denied-only] Optional. Configures logging policy for access requests. Sets the log type generated for access requests all Logs all access requests, both denied and permitted denied-only Logs only denied access ip-access-list Uses an IP access list to filter access requests <IP-ACCESS-LIST> Sets the access list name subnet <IP/M> Restricts access to a specified subnet. Uses a subnet IP address to filter access requests <IP/M> Sets the IP address of the subnet in the A.B.C.D/M format log [all| denied-only] Optional. Configures a logging policy for access requests. Sets the log type generated for access requests all Logs all access requests, both denied and permitted denied-only Logs only denied access subnet <IP/M> Restricts access to a specified subnet. Uses a subnet IP address to filter access requests <IP/M> Sets the IP address of the subnet in the A.B.C.D/M format host <IP> Uses the host IP address as a second filter <IP> Specify the host IP address. log [all|denied-only] Optional. Configures a logging policy for access requests. Sets the log type generated for access requests all Logs all access requests, both denied and permitted denied-only Logs only denied access
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 936 restrict-access subnet 172.16.10.20/24 host 172.16.10.3 log all restrict-access host 172.16.10.2 log all restrict-access host 172.16.10.4 log denied-only wm3400-34710C8(config-management-policy-test)# Related Commands snmp-server management-policy Enables the Simple Network Management Protocol (SNMP) engine parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax snmp-server [community|enable|host|manager|max-pending- request|throttle|user] snmp-server community <SNMP-COMMUNITY-STRING> [ro|rw] snmp-server enable [throttle|traps] snmp-server host <IP> [v2c|v3] {<1-65535>} snmp-server [manager [all|v2|v3]|max-pending-request <64-1024>] snmp-server throttle {interval [3000|5000|7000]} snmp-server user [snmpmanager|snmpoperator|snmptrap] snmp-server user [snmpmanager|snmpoperator|snmptrap] v3 [auth|encrypted] snmp-server user [snmpmanager|snmpoperator|snmptrap] v3 auth md5 [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>|<PASSWORD>] no Removes device access restrictions
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 937 snmp-server user [snmpmanager|snmpoperator|snmptrap] v3 encrypted [auth md5|des auth md5] [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>| <PASSWORD>] Parameters snmp-server community <SNMP-COMMUNITY-STRING> [ro|rw] snmp-server enable [throttle|traps] snmp-server host <IP> [v2c|v3] {<1-65535>} snmp-server [manager [all|v2|v3]|max-pending-request <64-1024>] snmp-server throttle {interval [3000|5000|7000]} community <SNMP-COMMUNITY- STRING> Sets the community string and access privileges. Enables SNMP access by configuring community strings that act like passwords. Configure different types of community strings, each string providing a different form of access. Provide either read-only (ro) or read-write (rw) access. <SNMP-COMMUNITY-STRING> Sets the SNMP community name [ro|rw] Select one of the following access types: ro Assigns read only access to a community string rw Assigns read and write access to a community string enable throttle Enables SNMP throttle enable traps Enables SNMP traps, sent to the management stations. Enabling this feature, ensures despatch of SNMP notifications to all hosts. host <IP> Configures a IP address of the host [v2c|v3] {1-65535} Configures the SNMP version used to send the traps v2c Uses SNMP version 2c v3 Uses SNMP version 3 <1-65535> Optional. Specifies the UDP port of the host <1-65535> Sets a value from 1 - 65535. The default value is 162. manager [all|v2|v3] Enables SNMP manager and specifies the SNMP version all Enables SNMP manager version v2 and v3 v2 Enables SNMP manager version v2 only v3 Enables SNMP manager version v3 only max-pending-request <64-1024> Sets the maximum pending access requests from 64 - 1024. The default is 128. throttle Enables CPU control on SNMP activities. Use this command to set the CPU throttle interval. interval Optional. Configures a delay time in microseconds 3000 Configures delay time as 3000 microseconds 5000 Configures delay time as 5000 microseconds 7000 Configures delay time as 7000 microseconds
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 938 snmp-server user [snmpmanager|snmpoperator|snmptrap] v3 auth md5 [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>|<PASSWORD>]] snmp-server user [snmpmanager|snmpoperator|snmptrap] v3 encrypted [auth md5|des auth md5] [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>|<PASSWORD>] Example wm3400-34710C8(config-management-policy-test)#snmp-server community snmp1 ro wm3400-34710C8(config-management-policy-test)# user [snmpmanager| snmpoperator| snmptrap] Defines user access to the SNMP engine snmpmanager Sets user as a SNMP manager snmpoperator Sets user as a SNMP operator snmptrap Sets user as a SNMP trap user v3 auth md5 Uses SNMP version 3 as the security model auth Uses an authentication protocol md5 Uses HMAC-MD5 algorithm for authentication [0 <PASSWORD>| 2 <ENCRYPTED- PASSWORD>| <PASSWORD>] Configures password using one of the following options: 0 <PASSWORD> Configures clear text password 2 <PASSWORD> Configures encrypted password <PASSWORD> Specifies a password for authentication and privacy protocols user [snmpmanager| snmpoperator| snmptrap] Defines user access to the SNMP engine snmpmanager Sets user as a SNMP manager snmpoperator Sets user as a SNMP operator snmptrap Sets user as a SNMP trap user v3 encrypted Uses SNMP version 3 as the security model encrypted Uses encrypted privacy protocol auth md5 Uses authentication protocol auth Sets authentication parameters md5 Uses HMAC-MD5 algorithm for authentication des auth md5 Uses privacy protocol for user privacy des Uses CBC-DES for privacy After specifying the privacy protocol, specify the authentication mode. auth Sets user authentication parameters md5 Uses HMAC-MD5 algorithm for authentication [0 <PASSWORD>| 2 <ENCRYPTED- PASSWORD>| <PASSWORD>] The following are common to both the auth and des parameters: Configures password using one of the following options: 0 <PASSWORD> Configures a clear text password 2 <PASSWORD> Configures an encrypted password <PASSWORD> Specifies a password for authentication and privacy protocols
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 939 wm3400-34710C8(config-management-policy-test)#snmp-server host 172.16.10.23 v3 162 wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#commit wm3400-34710C8(config-management-policy-test)#snmp-server user snmpmanager v3 auth md5 extreme123 wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#snmp-server throttle interval 3000 wm3400-34710C8(config-management-policy-test)#s wm3400-34710C8(config-management-policy-test)#show context management-policy test http server no ssh snmp-server community snmp1 ro snmp-server user snmpmanager v3 encrypted des auth md5 0 extreme123 snmp-server host 172.16.10.23 v3 162 snmp-server throttle interval 3000 wm3400-34710C8(config-management-policy-test)# Related Commands ssh management-policy Enables SSH for this management policy. SSH encrypts communication between the client and the server. no Disables the SNMP server settings
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 940 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ssh {port [<1-65535>]} Parameters ssh {port [<1-65535>]} Example wm3400-34710C8(config-management-policy-test)#ssh port 162 Book Dependant Variable(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test http server ssh port 162 snmp-server community snmp1 ro snmp-server user snmpmanager v3 encrypted des auth md5 0 extreme123 snmp-server enable traps snmp-server host 172.16.10.23 v3 62 restrict-access host 172.16.10.4 log denied-only wm3400-34710C8(config-management-policy-test)# Related Commands telnet management-policy ssh Enables SSH communication between client and server port <1-65535> Optional. Configures the SSH port <1-65535> Sets a value from 1 - 165535. The default port is 22. no Disables SSH access
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 941 Enables Telnet. By default Telnet is enabled on Transmission Control Protocol (TCP) port 23. Use this command to change the TCP port. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax telnet {port [<1-65535>]} Parameters telnet {port [<1-65535>]} Example wm3400-34710C8(config-management-policy-test)#telnet port 200 wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test telnet port 200 http server ssh port 162 snmp-server community snmp1 ro snmp-server user snmpmanager v3 encrypted des auth md5 0 extreme123 snmp-server enable traps snmp-server host 172.16.10.23 v3 62 restrict-access host 172.16.10.4 log denied-only wm3400-34710C8(config-management-policy-test)# telnet Enables Telnet port <1-65535> Optional. Configures the Telnet port <1-65535> Sets a value from 1 - 165535. The default port is 23.
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 942 Related Commands user management-policy Adds new user account Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax user <USERNAME> password [0 <PASSWORD>|1 <SHA1-PASSWORD>|<PASSWORD>] role [helpdesk| monitor|network-admin|security-admin|superuser|system-admin|web- user-admin] access [all|console|ssh|telnet|web] Parameters user <USERNAME> password [0 <PASSWORD>|1 <SHA1-PASSWORD>|<PASSWORD>] role [helpdesk|monitor|network-admin|security-admin|superuser|system-admin| web-user-admin] access [all|console|ssh|telnet|web] no Disables Telnet user <USERNAME> Adds new user account to this management policy <USERNAME> Sets the username password [0 <PASSWORD>| 1 <SHA1-PASSWORD>| <PASSWORD>] Configures a password 0 <PASSWORD> Sets a clear text password 1 <SHA1-PASSWORD> Sets the SHA1 hash of the password <PASSWORD> Sets the password
management-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 943 Example wm3400-34710C8(config-management-policy-test)#user TESTER password moto123 role superuser access all wm3400-34710C8(config-management-policy-test)# wm3400-34710C8(config-management-policy-test)#show context management-policy test telnet port 200 http server ssh port 162 user TESTER password 1 92d96356524478e04a6669c0c5a167a2d5f5ed0547c489b0d5b8662d879d3a1e role superuser access all snmp-server community snmp1 ro snmp-server user snmpmanager v3 encrypted des auth md5 0 extreme123 snmp-server enable traps snmp-server host 172.16.10.23 v3 62 restrict-access host 172.16.10.4 log denied-only wm3400-34710C8(config-management-policy-test)# Related Commands role Configures the user role. The options are: helpdesk Helpdesk administrator. Performs troubleshooting tasks, such as clear statistics, reboot, create and copy tech support dumps monitor Monitor. Has read-only access to the system. Can view configuration and statistics except for secret information network-admin Network administrator. Manages layer 2, layer 3, Wireless, RADIUS server, DHCP server, and Smart RF security-admin Security administrator. Modifies WLAN keys and passphrases superuser Superuser. Has full access, including halt and delete startup- config system-admin System administrator. Upgrades image, boot partition, time, and manages admin access web-user-admin Web user administrator. This role is used to create guest users and credentials. The Web user admin can access only the custom GUI screen and does not have access to the normal CLI and GUI. access [all|console|ssh| telnet|web] Configures the access type all Allows all types of access: console, SSH, Telnet, and Web console Allows console access ssh Allows SSH access telnet Allows Telnet access web Allows Web access no Removes a user account
Chapter 17: Management Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 944
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 945 C H A P T E R 18 RADIUS Policy This chapter summarizes RADIUS group, server and user policy commands in detail. Use the (config) instance to configure RADIUS group commands. This command creates a group within the existing Remote Authentication Dial-in user Service (RADIUS) group. To navigate to the RADIUS group instance, use the following commands: wm3400-34710C8(config)#radius-group <GROUP-NAME> wm3400-34710C8(config)#radius-group test wm3400-34710C8(config-radius-group-test)#? Radius user group configuration commands: guest Make this group a Guest group no Negate a command or set its defaults policy Radius group access policy configuration rate-limit Set rate limit for group clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-radius-group-test)# radius-group Sets RADIUS user group parameters The following table summarizes RADIUS group commands Command Description Reference guest Enables guest access for the newly created group page 18-946
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 946 guest radius-group Manages captive portal guest access. Creates a guest user and associates it with a group. The guest user and policies are used for captive portal authorization to the controller managed network. Supported in the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax guest Parameters None Example wm3400-34710C8(config-radius-group-test)#guest wm3400-34710C8(config-radius-group-test)# no Negates a command or sets its default values page 18-950 policy Configures RADIUS group access policy parameters page 18-947 rate-limit Sets the default rate limit per user in kbps, and applies it to all enabled WLANs page 18-949 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 6-418 write Writes information to memory or terminal page 7-425 Command Description Reference
radius-group Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 947 wm3400-34710C8(config-radius-group-test)#show context radius-group test guest wm3400-34710C8(config-radius-group-test)# Related Commands policy radius-group Sets the authorization policies for a RADIUS group, such as access day/time, WLANs etc. NOTE A user-based VLAN is effective only if dynamic VLAN authorization is enabled for the WLAN Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax policy [access|day|role|ssid|time|vlan] policy vlan <1-4094> policy access [all|console|ssh|telnet|web] policy access [all|console|ssh|telnet|web] {(all|console|ssh|telnet|web)} policy day [all|fr|mo|sa|su|th|tu|we|weekdays]{(all|fr|mo|sa|su| th|tu|we|weekdays)} policy role [helpdesk|monitor|network-admin|security-admin| super-user|system-admin|web-user-admin] policy ssid <SSID> policy time start <HH:MM> end <HH:MM> no Creates a non guest group
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 948 Parameters policy vlan <1-4094> policy access [all|console|ssh|telnet|web] {(all|console|ssh|telnet|web)} policy role [helpdesk|monitor|network-admin|security-admin|super-user| system-admin|web-user-admin] policy ssid <SSID> vlan <1-4094> Sets the RADIUS group VLAN ID from 1 - 4094 access Configures a group access type all Allows all access. Wireless client access to the console, ssh, telnet, and/or Web console Allows console access only ssh Allows SSH access only telnet Allows Telnet access only web Allows Web access only These parameters are optional you can use more than one at a time. role [helpdesk|monitor| network-admin| security-admin| super-user| system-admin| web-user-admin] Configures the role assigned to this RADIUS group helpdesk Helpdesk administrator. Performs troubleshooting tasks, such as clear statistics, reboot, create and copy tech support dumps monitor Monitor. Has read-only access to the system. Can view configuration and statistics except for secret information network-admin Network administrator. Manages layer 2, layer 3, Wireless, RADIUS server, DHCP server, and Smart RF security-admin Security administrator. Modifies WLAN keys and passphrases superuser Superuser. Has full access, including halt and delete startup config system-admin System administrator. Upgrades image, boot partition, time, and manages admin access web-user-admin Web user administrator. This role is used to create guest users and credentials. The web-user-admin can access only the custom GUI screen and does not have access to the normal CLI and GUI. ssid <SSID> Sets the Service Set Identifier (SSID) for this RADIUS group <SSID> Sets a case-sensitive alphanumeric SSID, not exceeding 32 characters
radius-group Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 949 policy day[all|fr|mo|sa|su|th|tu|we|weekdays] {(all|fr|mo|sa|su|th|tu|we| weekdays)} policy time start <HH:MM> end <HH:MM> Example wm3400-34710C8(config-radius-group-test)#policy access all wm3400-34710C8(config-radius-group-test)# wm3400-34710C8(config-radius-group-test)#policy time start 13:30 end 17:30 wm3400-34710C8(config-radius-group-test)# wm3400-34710C8(config-radius-group-test)#policy role superuser wm3400-34710C8(config-radius-group-test)# wm3400-34710C8(config-radius-group-test)#show context radius-group test policy time start 13:30 end 17:30 policy access web ssh telnet console policy role superuser wm3400-34710C8(config-radius-group-test)# Related Commands rate-limit radius-group day [all|fr|mo|sa| su|th|tu|we|weekdays] Configures the days on which this RADIUS group can access the network. The options are. all Allows access on all days (Sunday to Saturday) fr Allows access on Friday only mo Allows access on Mondays only sa Allows access on Saturdays only su Allows access on Sundays only th Allows access on Thursdays only tu Allows access on Tuesdays only we Allows access on Wednesdays only weekdays Allows access on weekdays only (Monday to Friday These parameters are optional, you can provide access on multiple days time start<HH:MM> end <HH:MM> Configures the time when this RADIUS group can access the network start <HH:MM> Sets the start time in the HH:MM format (for example, 13:30 means the user can login only after 1:30 PM) end <HH:MM> Sets the end time in the HH:MM format (for example, 17:30 means the user is allowed to remain logged in until 5:30 PM) no Removes or modifies a RADIUS groups access settings
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 950 Sets the rate limit for the RADIUS server group Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rate-limit [from-air|to-air] <100-1000000> Parameters rate-limit [from-air|to-air] <100-1000000> Usage Guidelines Use [ no] r at e- l i mi t [ wi r ed- t o- wi r el ess| wi r el ess- t o- wi r ed] to remove the rate limit applied to the group. [ no] r at e- l i mi t [ wi r el ess- t o- wi r ed] sets the rate limit back to unlimited Example wm3400-34710C8(config-radius-group-test)##rate-limit to-air 101 wm3400-34710C8(config-radius-group-test)# Related Commands no radius-group Negates a command or sets its default. Removes or modifies the RADIUS group policy settings. When used in the config RADIUS group mode, the no command removes or modifies the following settings: access type, access days, role type, VLAN ID, and SSID. to-air <100-1000000> Sets the rate limit in the downlink direction, from the network to the wireless client <100-1000000> Sets the rate from 100 - 1000000 Kbps from-air <100-1000000> Sets the rate limit in the uplink direction, from the wireless client to the network <100-1000000> Sets the rate from 100 - 1000000 Kbps no Removes the RADIUS groups rate limits
radius-group Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 951 Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [guest|policy|rate-limit] no policy [access|day|role|ssid|time|vlan] no policy access [all|console|ssh|telnet|web] no policy day [all|fr|mo|sa|su|th|tu|we|weekdays] no policy ssid [<SSID>|all] no policy [role|time|vlan] no rate-limit [from-air|to-air] Parameters no guest no policy access [all|console|ssh|telnet|web] no guest Makes this RADIUS group a non guest group no policy access Removes or modifies the RADIUS group access all Removes all access (Wireless client access to the console, SSH, Telnet, and Web) console Removes console access ssh Removes SSH access telnet Removes Telnet web Removes Web access These are recursive options, and you can remove more than one at a time.
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 952 no policy day [all|fr|mo|sa|su|th|tu|we|weekdays] no policy ssid [<SSID>|all] no policy [role|time|vlan] no rate-limit [from-air|to-air] Example wm3400-34710C8(config-radius-group-test)#no guest wm3400-34710C8(config-radius-group-test)# no policy days Removes or modifies the days on which access is provided to this RADIUS group all Removes access on all days (Monday to Sunday) fr Removes access on Fridays only mo Removes access on Mondays only sa Removes access on Saturdays only su Removes access on Sundays only th Removes access on Thursdays only tu Removes access on Tuesdays only we Removes access on Wednesdays only weekdays Removes access on weekdays (Monday to Friday) These are recursive options, and you can remove more than one at a time. no policy ssid Removes the RADIUS groups SSID <SSID> Specify the RADIUS group SSID all Removes all allowed WLANs no policy role Removes the RADIUS groups role no policy time Removes the RADIUS groups start and end access time no policy vlan Removes the RADIUS groups VLAN ID no rate-limit Removes RADIUS groups rate limit from-air Removes the rate limit in the uplink direction, from the wireless client to the network to-air Sets the rate limit in the downlink direction, from the network to the wireless client
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 953 Related Commands radius-server-policy Creates an onboard device RADIUS server policy. Use the (config) instance to configure RADIUS-Server-Policy related configuration commands. To navigate to the RADIUS-Server-Policy instance, use the following commands: wm3400-34710C8(config)#radius-server-policy <POLICY-NAME> wm3400-34710C8(config)#radius-server-policy test wm3400-34710C8(config-radius-server-policy-test)# The following table summarizes RADIUS server policy commands authentication radius-server-policy guest Manages a guest user linked with a hotspot policy Sets a RADIUS groups authorization policies rate-limit Sets a RADIUS groups rate limit Commands Description Reference authentication Configures RADIUS authentication parameters page 18-953 crl-check Enables a certificate revocation list (CRL) check page 18-955 ldap-group- verification Enables the LDAP group verification settings page 18-956 ldap-server Configures the LDAP server parameters page 18-956 local Configures a local RADIUS realm page 18-958 nas Configures the key sent to a RADIUS client page 18-959 no Negates a command or sets its defaults page 18-960 proxy Configures the RADIUS proxy server settings page 18-963 session-resumption Enables session resumption page 18-965 use Defines settings used with the RADIUS server policy page 18-965 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in this current session page 6-380 do Runs commands in the EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to the their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug (config-if) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 954 Configures RADIUS server authentication parameters Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication [data-source|eap-auth-type] authentication data-source [ldap {fallback}|local] authentication eap-auth-type [all|peap-gtc|peap-mschapv2|tls|ttls-md5| ttls-mschapv2|ttls-pap] Parameters authentication data-source [ldap|local] authentication eap-auth-type [all|peap-gtc|peap-mschapv2|tls|ttls-md5| ttls-mschapv2|ttls-pap] Example wm3400-34710C8(config-radius-server-policy-test)#authentication eap-auth- type tls wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context data-source The RADIUS sever can use multiple data sources to authenticate a user. It is necessary to specify the data source. The options are: LDAP and local ldap {fallback} Uses a remote Lightweight Directory Access Protocol (LDAP) server as the data source fallback Optional. Enables fallback to local authentication. This feature ensures that when the configured LDAP data source is unreachable, the client is authenticated against the local RADIUS resource. local Uses the local user database to authenticate a user eap-auth-type Uses the Extensible Authentication Protocol (EAP) to authenticate the user all Enables both TTLS and PEAP authentication peap-gtc Enables PEAP with default GTC peap-mschapv2 Enables PEAP with default MSCHAPv2 tls Enables TLS ttls-md5 Enables TTLS with default md5 ttls-mschapv2 Enables TTLS with default MSCHAPv2 ttls-pap Enables TTLS with default PAP
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 955 radius-server-policy test authentication eap-auth-type tls wm3400-34710C8(config-radius-server-policy-test)# Related Commands crl-check radius-server-policy Enables a certificate revocation list (CRL) check on this RADIUS server policy Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax crl-check Parameters None Example wm3400-34710C8(config-radius-server-policy-test)#crl-check wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context radius-server-policy test authentication eap-auth-type tls crl-check wm3400-34710C8(config-radius-server-policy-test)# no Removes RADIUS authentication settings
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 956 Related Commands ldap-group-verification radius-server-policy Enables LDAP group verification settings on this RADIUS server policy Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ldap-group-verification Parameters None Example wm3400-34710C8(config-radius-server-policy-test)#ldap-group-verification wm3400-34710C8(config-radius-server-policy-test)# Related Commands ldap-server radius-server-policy Configures LDAP server parameters. Configuring LDAP server allows users to login and authenticate from anywhere on the network. no Disables CRL check on a RADIUS server policy no Disables LDAP group verification settings
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 957 Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ldap-server [dead-period|primary|secondary] ldap-server [dead-period <0-600>] ldap-server [primary|secondary] host <IP> port <1-65535> login <LOGIN-ID> bind-dn <BIND-DN> base-dn <BASE-DN> passwd [0 <PASSWORD>|2 <ENCRYPTED- PASSWORD>|<PASSWORD>] passwd-attr <ATTR> group-attr <ATTR> group- filter <FILTER> group-membership <WORD> {net-timeout <1-10>}] Parameters ldap-server [dead-period <0-600>] ldap-server [primary|secondary] host <IP> port <1-65535> login <LOGIN-ID> bind-dn <BIND-DN> base-dn <BASE-DN> passwd [0 <PASSWORD>|2 <ENCRYPTED- PASSWORD>|<PASSWORD>] passwd-attr <ATTR> group-attr <ATTR> group-filter <FILTER> group-membership <WORD> {net-timeout <1-10>}] dead-period <0-600> Sets the dead period the RADIUS server will not contact the LDAP server after finding it unavailable. This is valid only when redundant LDAP servers are configured. <0-600> Sets a value from 0 - 600 seconds ldap primary Configures primary LDAP server settings ldap secondary Configures secondary LDAP server settings host <IP> Specifies the LDAP host IP address <IP> Sets the LDAP servers IP address port <1-65535> Configures the LDAP server port <1-65535> Sets a port between 1 - 65535 login <LOGIN-ID> Configures the login ID of a user to access the LDAP server <LOGIN-ID> Sets a 127 characters maximum login ID bind-dn <BIND-DN> Configures a distinguished bind name <BIND-DN> The bind name should not exceed 127 characters base-dn <BASE-DN> Configures a distinguished base name <BASE-DN> Sets the distinguished base name
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 958 Example wm3400-34710C8(config-radius-server-policy-test)#ldap-server primary host 172.16.10.19 port 162 login extreme bind-dn bind-dn1 base-dn base-dn1 passwd 0 extreme1 passwd-attr moto123 group-attr grop1 group-filter gropfilter1 group-membership gropmember ship1 net-timeout 2 wm3400-34710C8(config-radius-server-policy-test)#ldap-server secondary host 172.16.10.2 port 2 login word bind-dn word1 base- dn word2 passwd 0 word4 passwd-attr word4 group-attr word5 group-filter word6 group-membership word8 net-timeout 3 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context radius-server-policy test authentication data-source ldap crl-check ldap-server primary host 172.16.10.19 port 162 login extreme bind-dn bind- dn1 base-dn base-dn1 passwd 0 extreme1 passwd-attr moto123 group-attr grop1 group-filter gropfilter1 group-membership gropmembership1 net-timeout 2 wm3400-34710C8(config-radius-server-policy-test)# Related Commands local radius-server-policy Configures a local RADIUS realm on this RADIUS server policy passwd [0 <PASSWORD>| 2 <ENCRYPTED- PASSWORD>|<PASSWO RD>] Sets the LDAP server password 0 <PASSWORD> Sets an UNENCRYPTED password 2 <PASSWORD> Sets an ENCRYPTED password <PASSWORD> Sets the LDAP server bind password, specified UNENCRYPTED, with a maximum size of 31 characters passwd-attr <ATTR> Specify a name to configure the LDAP server password attribute (should not exceed 63 characters) group-attr <ATTR> Specify a name to configure group attributes (should not exceed 31 characters) group-filter <FILTER> Specify a name for the group filter attribute (should not exceed 255 characters) group-membership <WORD> Specify a name for the group membership attribute (should not exceed 63 characters) net-time <1-10> Select a value from 1 - 10 to configure network timeout (number of seconds to wait for response from the server) no Disables the LDAP server parameters
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 959 Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax local realm <RADIUS-REALM> Parameters local realm <RADIUS-REALM> Example wm3400-34710C8(config-radius-server-policy-test)#local realm realm1 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context radius-server-policy test authentication eap-auth-type tls crl-check local realm realm1 ldap-server dead-period 600 wm3400-34710C8(config-radius-server-policy-test)# Related Commands nas radius-server-policy Configures the key sent to a RADIUS client realm <RADIUS-REALM> Configures a local RADIUS realm <RADIUS-REALM> Sets a local RADIUS realm name (a string not exceeding 50 characters) no Removes RADIUS local realm
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 960 Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax nas <IP/M> secret [0|2|<LINE>] nas <IP/M> secret [0 <LINE>|2 <LINE>|<LINE>] Parameters nas <IP/M> secret [0 <LINE>|2|<LINE>] Example wm3400-34710C8(config-radius-server-policy-test)#nas 172.16.10.10/24 secret 0 wirelesswell wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context radius-server-policy test authentication eap-auth-type tls crl-check nas 172.16.10.10/24 secret 0 wirelesswell local realm realm1 ldap-server dead-period 600 wm3400-34710C8(config-radius-server-policy-test)# Related Commands no radius-server-policy <IP/M> Sets the RADIUS clients IP address <IP/M> Sets the RADIUS clients IP address in the A.B.C.D/M format secret [0 <LINE>|2 <LINE>| <LINE>] Sets the RADIUS clients shared secret. Use one of the following options: 0 <LINE> Sets an UNENCRYPTED secret 2 <LINE> Sets an ENCRYPTED secret <LINE> Defines the secret (client shared secret) up to 32 characters no Removes a RADIUS servers client on a RADIUS server policy
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 961 Negates a command or reverts back to default settings. When used with in the config RADIUS server policy mode, the no command removes settings, such as crl-check, LDAP group verification, RADIUS client etc. Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [authentication|clr-check|ldap-group-verification|ldap-server|local| nas|proxy|session-resumption|use] no authentication [data-source {ldap {fallback}|local}|eap configuration] no [clr-check|ldap-group-verification|nas <IP/M>|session-resumption] no local realm [<REALM-NAME>|all] no proxy [realm <REALM-NAME>|retry-count|retry-delay] no ldap-server [dead-period|primary|secondary] no use [radius-group [<RAD-GROUP>|all]|radius-user-pool-policy [<RAD-USER-POOL>|all]] Parameters no authentication [data-source|eap configuration]] no [clr-check|ldap-group-verification|nas <IP/M>|session-resumption] no authentication Removes RADIUS authentication settings data-source {ldap {fallback}|local} Removes configured data source ldap {fallback} Optional. Removes remote LDAP server as the data source for user authentication fallback Optional. Disables fallback to local autehntication in case LDAP authentication fails local Removes local database as the source of user authentication eap configuration Resets EAP authentication to the default mode no crl-check Removes the CRL check no ldap-group-verification Disables a RADIUS servers LDAP group verification settings no nas Removes a RADIUS servers client <IP/M> Sets the IP address of the RADIUS client in the A.B.C.D/M format
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 962 no local realm [<REALM-NAME>|all] no proxy [realm <REALM-NAME>|retry-count|retry-delay] no ldap-server [dead-period|primary|secondary]] no use [radius-group [<RAD-GROUP>|all]|radius-user-pool-policy [<RAD-USER- POOL>|all]] Example wm3400-34710C8(config-radius-server-policy-test)#no use server-trustpoint wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#no no local realm all wm3400-34710C8(config-radius-server-policy-test)# no session-resumption Disables a RADIUS servers session resumption settings no local Removes a RADIUS servers local realm realm <REALM-NAME> Specify the realm name no proxy Removes a RADIUS proxy server realm <REALM-NAME> Removes a RADIUS proxy servers realm name <REALM-NAME> Specify the realm name retry-count Removes a proxy server retry count retry-delay Removes a proxy server retry delay count no ldap-server Disables the LDAP server parameters dead-period Sets the dead period as the duration the RADIUS server will not contact the LDAP server after finding it unavailable. primary Removes the primary LDAP server secondary Removes the secondary LDAP server no use Removes the RADIUS group or a RADIUS user pool policy radius-group <RAD-GROUP> Removes a specific RADIUS group or all RADIUS groups <RAD-GROUP> Specify the RADIUS group name all Removes all RADIUS groups radius-user-pool-policy [<RAD-USER- POOL>|all] Removes a specific RADIUS user pool or all RADIUS user pools <RAD-USER-POOL> Enter the RADIUS user pool name all Removes all RADIUS user pools
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 963 Related Commands proxy radius-server-policy Configures a proxy RADIUS server based on the realm/suffix. The realm identifies where the RADIUS server forwards AAA requests for processing. Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax proxy [realm|retry-count|retry-delay] proxy realm <REALM-NAME> server <IP> port <1024-65535> secret [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>|<PASSWORD>] proxy retry-count <3-6> proxy retry-delay <5-10>] Parameters proxy realm <REALM-NAME> server <IP> port <1024-65535> secret [0 <PASSWORD>|2 <ENCRYPTED-PASSWORD>|<PASSWORD>] authentication Configures RADIUS server authentication parameters crl-check Enables a CRL check ldap-group-verification Enables LDAP group verification settings ldap-server Configures the LDAP server parameters. Configuring the LDAP server allows users to login and authenticate from anywhere on the network local Configures a local RADIUS realm on this RADIUS server policy nas Configures the key sent to a RADIUS client proxy Configures a proxy RADIUS server based on the realm/suffix session-resumption Enables session resumption/fast re-authentication by using cached attributes use Defines settings used with the RADIUS server policy proxy realm <REALM- NAME> Configures the realm name <REALM-NAME> Specify the realm name. The name should not exceed 50 characters.
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 964 proxy retry-count <3-6> proxy retry-delay <5-10> Usage Guidelines Only five RADIUS proxy servers can be configured. The proxy server attempts six retries before it times out. The retry count defines the number of times the wireless controller transmits each RADIUS request before giving up. The timeout value defines the duration for which the wireless controller waits for a reply to a RADIUS request before retransmitting the request. Example wm3400-34710C8(config-radius-server-policy-test)#proxy realm test1 server 172.16.10.7 port 1025 secret 0 extreme123 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#proxy retry-count 4 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#proxy retry-delay 8 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#show context radius-server-policy test proxy retry-delay 8 proxy retry-count 4 proxy realm test1 server 172.16.10.7 port 1025 secret 0 extreme123 wm3400-34710C8(config-radius-server-policy-test)# server <IP> Configures the proxy servers IP address <IP> Sets the proxy servers IP address port <1024-65535> Configures the proxy servers port <1024-65535> Sets the proxy servers port from 1024 - 65535 secret [0 <PASSWORD>| 2 <ENCRYPTED- PASSWORD>| <PASSWORD> Sets the proxy server secret string. The options are: 0 <PASSWORD> Sets an UNENCRYPTED password 2 <ENCRYPTED-PASSWORD> Sets an ENCRYPTED password <PASSWORD> Sets the proxy server shared secret value retry-count <3-6> Sets the proxy server retry count <3-6> Sets a value from 3 - 6 retry-delay <5-10> Sets the proxy server retry delay count <5-10> Sets a value from 5 - 10 seconds
radius-server-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 965 Related Commands session-resumption radius-server-policy Enables session resumption or fast re-authentication by using cached attributes Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax session-resumption {life-time|max-entries} session-assumption {life-time [<1-24>]|max-entries [<10-1024>]} Parameters session-assumption {life-time [<1-24>]|max-entries [<10-1024>]} Example wm3400-34710C8(config-radius-server-policy-test)#session-resumption lifetime 10 max-entries 11 wm3400-34710C8(config-radius-server-policy-test)# Related Commands use radius-server-policy no Removes the RADIUS proxy server settings life-time <1-24> Optional. Sets the lifetime of cached entries <1-24> Specify the lifetime period from 1 - 24 hours max-entries <10-1024> Optional. Configures the maximum number of entries in the cache. <10-1024> Sets the maximum number of entries in the cache from 10 - 1024 no Disables session resumption feature on this RADIUS server policy
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 966 Defines settings used with the RADIUS server policy Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [radius-group <RAD-GROUP> {RAD-GROUP}|radius-user-pool-policy <RAD-USER-POOL>] Parameters use [radius-group <RAD-GROUP> {RAD-GROUP}|radius-user-pool-policy <RAD-USER-POOL> Example wm3400-34710C8(config-radius-server-policy-test)#use server-trustpoint name1 wm3400-34710C8(config-radius-server-policy-test)# wm3400-34710C8(config-radius-server-policy-test)#use radius-user-pool- policy testuser wm3400-34710C8(config-radius-server-policy-test)# Related Commands radius-user-pool-policy Configures a RADIUS user pool policy Use the (config) instance to configure RADIUS user pool policy commands. To navigate to the radius-user-pool-policy instance, use the following commands: wm3400-34710C8(config)#radius-user-pool-policy <POOL-NAME> wm3400-34710C8(config)#radius-user-pool-policy testuser radius-group <RAD- GROUP> {RAD-GROUP} Configures a RADIUS group (for LDAP users) radius-user-pool-policy <RAD-USER-POOL> Configures RADIUS user pool parameters. Specify a user pool name up to 32 characters no Removes a RADIUS group or a RADIUS user pool policy
radius-user-pool-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 967 wm3400-34710C8(config-radius-user-pool-testuser)# The following table summarizes RADIUS user pool policy commands user radius-user-pool-policy Configures RADIUS user parameters Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax user <USERNAME> password [0 <UNECRYPTED-PASSWORD>|2 <ECRYPTED- PASSWORD>|<PASSWORD>] {group [<RAD-GROUP>] {<RAD-GROUP>|guest}} user <USERNAME> password [0 <UNECRYPTED-PASSWORD>|2 <ECRYPTED- PASSWORD>|<PASSWORD>] {group [<RAD-GROUP>] {guest expiry-time <HH:MM> expiry-date <MM:DD:YYY> start-time} <HH:MM> start-date <MM:DD:YYYY>}} Commands Description Reference user Configures RADIUS user parameters page 18-968 no Negates a command or sets its default value page 18-968 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug (config-if) instance configurations page 6-391 show Displays running system information page 6-418 write Writes information to memory or terminal page 7-425
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 968 Parameters user <USERNAME> password [0 <UNECRYPTED-PASSWORD>|2 <ECRYPTED- PASSWORD>|<PASSWORD>] {group [<RAD-GROUP>] {guest expiry-time <HH:MM> expiry-date <MM:DD:YYY> start-time} <HH:MM> start-date <MM:DD:YYYY>}} Example wm3400-34710C8(config-radius-user-pool-testuser)#user testuser password 0 extreme123 group test guest expiry-time 13:20 expiry- date 12:15:2011 start-time 17:00 start-date 11:15:2011 wm3400-34710C8(config-radius-user-pool-testuser)# Related Commands no radius-user-pool-policy Negates a command or sets its default. When used in the RADIUS user pool policy mode, the no command deletes a user from a RADIUS user pool user <USERNAME> Adds a new RADIUS user to the RADIUS user pool <USERNAME> Specify the name of the user. The username should not exceed 64 characters. passwd [0 <UNENCRYPTED- PASSWORD>| 2 <ENCRYPTED- PASSWORD>| <PASSWORD>] Configures the user password 0 <UNENCRYPTED-PASSWORD> Sets an unencrypted password 2 <ENCRYPTED-PASSWORD> Sets an encrypted password <PASSWORD> Sets a password (specified unencrypted) up to 21 characters in length group <RAD-GROUP> Optional. Configures a RADIUS server group <RAD-GROUP> Specify a group name in the local database guest Optional. Enables guest user access. After enabling a guest user account, specify the start and expiry time and date for this account. expiry-time <HH:MM> Optional. Specify the user account expiry time in the HH:MM format (for example, 12:30 means 30 minutes after 12:00 the user login will expire). expiry-date <MM:DD:YYYY> Optional. Specify the user account expiry date in the MM:DD:YYYY format (for example. 12:15:2011). start-time <HH:MM> Optional. Specify the user account activation time in the HH:MM format. start-date <MM:DD:YYYY> Optional. Specify the user account activation date in the MM:DD:YYYY format. no Deletes a user from a RADIUS user pool
radius-user-pool-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 969 Supported on the following platforms: AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no user <USERNAME> Parameters no user <USERNAME> Example wm3400-34710C8(config-radius-user-pool-testuser)#no user testuser wm3400-34710C8(config-radius-user-pool-testuser)# Related Commands user <USERNAME> Deletes a RADIUS user <USERNAME> Specify the user name. user Configures RADIUS user parameters
Chapter 18: RADIUS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 970
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 971 C H A P T E R 19 Radio QoS Policy This chapter summarizes the radio QoS policy in detail. Configuring and implementing a radio QOS policy is essential for WLANs with heavy traffic and less bandwidth. The policy enables you to provide preferential service to selected network traffic by controlling bandwidth allocation. The radio QoS policy can be applied to VLANs configured on an access point. In case no VLANs are configured, the radio QoS policy can be applied to an access points Ethernet and radio ports. Use the (config) instance to configure radios QoS policy related configuration commands. To navigate to the radio QoS policy instance, use the following commands: wm3400-34710C8(config)#radio-qos-policy <POLICY-NAME> wm3400-34710C8(config)#radio-qos-policy test wm3400-34710C8(config-radio-qos-test)#? Radio QoS Mode commands: accelerated-multicast Configure multicast streams for acceleration admission-control Configure admission-control on this radio for one or more access categories no Negate a command or set its defaults wmm Configure 802.11e/Wireless MultiMedia parameters clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-radio-qos-test)#
Chapter 19: Radio QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 972 radio-qos-policy The following table summarizes radio QoS policy commands accelerated-multicast radio-qos-policy Configures multicast streams for acceleration. Multicasting allows the group transmission of data streams. AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accelerated-multicast [client-timeout|max-client-streams|max-streams| overflow-policy|stream-threshold] Command Description Reference accelerated- multicast Configures multicast streams for acceleration page 19-972 admission-control Enables admission control across all radios for one or more access categories page 19-973 no Negates a command or resets configured settings to their default page 19-975 wmm Configures 802.11e/wireless multimedia parameters page 19-978 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
radio-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 973 accelerated-multicast [client-timeout <5-6000>|max-client-streams <1-4>| max-streams <0-256>|overflow-policy [reject|revert]|stream-threshold <1-500>] Parameters accelerated-multicast [client-timeout <5-6000>|max-client-streams <1-4>|max-streams <0-256>|overflow-policy [reject|revert]|stream-threshold <1-500>] Example wm3400-34710C8(config-radio-qos-test)#accelerated-multicast client-timeout 500 wm3400-34710C8(config-radio-qos-test)#accelerated-multicast stream- threshold 15 wm3400-34710C8(config-radio-qos-test)#show context radio-qos-policy test accelerated-multicast stream-threshold 15 accelerated-multicast client-timeout 500 wm3400-34710C8(config-radio-qos-test)# Related Commands admission-control radio-qos-policy Enables admission control across all radios for one or more access categories. Enabling admission control for an access category, ensures clients associated to an access point complete WMM admission control before using that access category. client-timeout <5-6000> Configures a timeout period in seconds for wireless clients <5-6000> Specify a value from 5 - 6000 seconds. max-client-streams <1-4> Configures the maximum number of accelerated multicast streams per client <1-4> Specify a value from 1 - 4. The default is 2. max-streams <0-256> Configures the maximum number of accelerated multicast streams per radio <0-256> Specify a value from 0 - 256. The default is 25. overflow-policy [reject|revert] Specifies the policy in case too many clients register simultaneously. The radio QOS policy can be configured to follow one of the following courses of action: reject Rejects new clients. The default overflow policy is reject. revert Reverts to regular multicast delivery stream-threshold <1-500> Configures the number of packets per second threshold for streams to accelerate <1-500> Specify a value from 1 - 500. The default is 30. no Reverts accelerated multicasting settings to their default
Chapter 19: Radio QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 974 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax admission-control [background|best-effort|firewall-detected-traffic| implicit-tspec|video|voice] admission-control [firewall-detected-traffic|implicit-tspec] admission-control [background|best-effort|video|voice] {max-airtime- percent|max-clients|max-roamed-clients|reserved-for-roam-percent} admission-control [background|best-effort|video|voice] {max-airtime- percent [<0-150>]|max-clients [<0-256>]|max-roamed-clients [<0- 256>]| reserved-for-roam-percent [<0-150>]} Parameters admission-control [firewall-detected-traffic|implicit-tspec] admission-control [background|best-effort|video|voice] {max-airtime- percent [<0-150>]|max-clients [<0-256>]|max-roamed-clients [<0-256>]| reserved-for-roam-percent [<0-150>]} admission-control firewall- detected-traffic Enforces admission control for traffic whose access category is detected by the firewall Application Layer Gateways (ALG). For example, Session Initiation Protocol (SIP) voice calls admission-control implicit- tspec Enables implicit traffic specifiers for clients that do not support WMM TSPEC, but are accessing admission-controlled access categories admission-control background Configures background access category admission control parameters admission-control best-effort Configures best effort access category admission control parameters admission-control video Configures video access category admission control parameters admission-control voice Configures voice access category admission control parameters
radio-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 975 Example wm3400-34710C8(config-radio-qos-test)#admission-control best-effort max- clients 200 wm3400-34710C8(config-radio-qos-test)#admission-control voice reserved-for- roam-percent 8 wm3400-34710C8(config-radio-qos-test)#admission-control voice max-airtime- percent 9 wm3400-34710C8(config-radio-qos-test)#show context radio-qos-policy test admission-control voice max-airtime-percent 9 admission-control voice reserved-for-roam-percent 8 admission-control best-effort max-clients 200 accelerated-multicast stream-threshold 15 accelerated-multicast client-timeout 500 wm3400-34710C8(config-radio-qos-test)# Related Commands no radio-qos-policy Negates a command or resets configured settings to their default. When used in the radio QOS policy mode, the no command enables the resetting of accelerated multicast parameters, admission control parameters, and MultiMedia parameters. max-airtime-percent <0-150> Optional. Specifies the maximum percentage of airtime, including oversubscription, for this access category <0-150> Specify a value from 0 - 150. This is the maximum percentage of airtime, including oversubscription, for this access category. The default is 75%. max-clients <0-256> Optional. Specifies the maximum number of wireless clients admitted to this access category <0-256> Specify a value from 0 - 256. This is the maximum number of wireless clients admitted to this access category. The default is 100 clients. max-roamed-clients <0-256> Optional. Specifies the maximum number of roaming wireless clients admitted to this access category <0-256> Specify a value from 0 - 256. This is the maximum number of roaming wireless clients admitted to this access category. the default is 10 roamed clients. reserved-for-roam-percent <0-150> Optional. Calculates the percentage of air time, including oversubscription, allocated exclusively for roaming clients. This value is calculated relative to the configured max air time for this access category. <0-150> Specify a value from 0 - 150. This is the percentage of air time, including oversubscription, allocated exclusively for roaming clients associated with this access category. the default is 10%. no Reverts or resets admission control settings to their default
Chapter 19: Radio QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 976 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [accelerated-multicast|admission-control|wmm] no accelerated-multicast [client-timeout|max-client-streams| max-streams|overflow-policy|stream-threshold] no admission-control [firewall-detected-traffic|implicit-tspec] no admission-control [background|best-effort|video|voice] {max-airtime- percent|max-clients|max-roamed-clients|reserved-for-roam-percent} no wmm [background|best-effort|video|voice] [aifsn|cw-max|cw-min| txop-limit] Parameters no accelerated-multicast [client-timeout|max-client-streams| max-streams|overflow-policy|stream-threshold] no admission-control [firewall-detected-traffic|implicit-tspec] no accelerated-multicast Resets accelerated multicasting settings to their default values. The following accelerated multicast control settings can be reverted: client-timeout Resets the client timeout to the default value max-client-streams Resets the maximum number of accelerated streams per client to the default value max-streams Resets the maximum number of accelerated streams to the default value overflow-policy Resets the overflow policy to the default value (reject) stream-threshold Resets the number of packets per second threshold to the default value no admission-control Reverts or resets admission control settings to their default. These controls are configured on a radio for one or more access categories. firewall-detected-traffic Does not enforce admission control for traffic whose access category is detected by the firewall ALG implicit-tspec Disables implicit traffic specifiers for wireless clients that do not support WMM-TSPEC
radio-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 977 no admission-control [background|best-effort|video|voice] {max-airtime- percent|max-clients|max-roamed-clients|reserved-for-roam-percent} no wmm [background|best-effort|video|voice] [aifsn|cw-max|cw-min| txop-limit] Example The Radio-qos-policy settings before execution of the no command: wm3400-34710C8(config-radio-qos-test)#show context radio-qos-policy test admission-control voice max-airtime-percent 9 admission-control voice reserved-for-roam-percent 8 admission-control best-effort max-clients 200 accelerated-multicast stream-threshold 15 accelerated-multicast client-timeout 500 wm3400-34710C8(config-radio-qos-test)# The Radio-qos-policy settings after execution of the no command: no admission-control Reverts or resets admission control settings to their default. These controls are configured on a radio for one or more access categories. background Resets background access category admission control best-effort Resets best effort access category admission control video Resets video access category admission control voice Resets voice access category admission control max-airtime-percent Optional. Resets the maximum percentage of airtime used by this access category to its default (75%) max-clients Optional. Resets the maximum number of wireless clients admitted by this access category to its default (100 clients) max-roamed-clients Optional. Resets the maximum number of roaming wireless clients admitted by this access category to its default (10 roamed clients) reserved-for-roam-percent Resets the percentage of air time allocated exclusively for roaming wireless clients to its default (10%) no wmm Reverts or resets 802.11e/wireless multimedia settings to default background Resets background access category wireless multimedia settings best-effort Resets best effort access category wireless multimedia settings video Resets video access category wireless multimedia settings voice Resets voice access category wireless multimedia settings The following are common to the background, best-effort, video, and voice parameters: aifsn Resets Arbitration Inter Frame Spacing Number (AIFSN) to its default cw-max Resets maximum contention window to its default cw-min Resets minimum contention window to its default txop-limit Resets transmit opportunity limit to its default
Chapter 19: Radio QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 978 wm3400-34710C8(config-radio-qos-test)#no admission-control best-effort max- clients wm3400-34710C8(config-radio-qos-test)#no accelerated-multicast client- timeout wm3400-34710C8(config-radio-qos-test)#show context radio-qos-policy test admission-control voice max-airtime-percent 9 admission-control voice reserved-for-roam-percent 8 accelerated-multicast stream-threshold 15 wm3400-34710C8(config-radio-qos-test)# Related Commands wmm radio-qos-policy Configures 802.11e/wireless multimedia parameters Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wmm [background|best-effort|video|voice] wmm [background|best-effort|video|voice] [aifsn <1-15>|cw-max <0-15>| cw-min <0-15>|txop-limit <0-65535>] Parameters wmm [background|best-effort|video|voice] [aifsn <1-15>|cw-max <0-15>| cw-min <0-15>|txop-limit <0-65535>] accelerated-multicast Configures multicast streams for acceleration. Multicasting allows the group transmission of data streams admission-control Enables admission control across all radios for one or more access categories wmm Configures 802.11e/wireless multimedia parameters wmm background Configures background access category wireless multimedia parameters
radio-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 979 Example wm3400-34710C8(config-radio-qos-test)#wmm best-effort aifsn 7 wm3400-34710C8(config-radio-qos-test)#wmm voice txop-limit 1 wm3400-34710C8(config-radio-qos-test)#show context radio-qos-policy test wmm best-effort aifsn 7 wmm voice txop-limit 1 wm3400-34710C8(config-radio-qos-test)# Related Commands wmm best-effort Configures best effort access category wireless multimedia parameters wmm video Configures video access category wireless multimedia parameters wmm voice Configures voice access category wireless multimedia parameters aifsn <1-15> Configures AIFSN as the wait time between data frames derived from the AIFSN and slot time <1-15> Sets a value from 1 - 15 cw-max <0-15> Maximum contention window: Clients pick a number between 0 and the min contention window to wait before retransmission. Clients then double their wait time on a collision, until it reaches the maximum contention window. <0-15> ECW: the contention window. The actual value used is (2^ECW - 1). cw-min <0-15> Minimum contention window: Clients select a number between 0 and the min contention window to wait before retransmission. Clients then double their wait time on a collision, until it reaches the maximum contention window. <0-15> ECW: the contention window. The actual value used is (2^ECW - 1). txop-limit <0-65535> Configures the transmit opportunity limit: The interval a particular client can initiate transmissions <0-65535> Specify a value from 0 - 65535 to configure the transmit opportunity limit in 32 microsecond units. no Reverts or resets 802.11e/wireless multimedia settings to their default
Chapter 19: Radio QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 980
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 981 C H A P T E R 20 Role Policy A role policy defines the rules that associates tasks and devices with specific roles. A role is as a class of users with a specific set of requirements and responsibilities. By defining roles, you are actually defining different user groups. A well defined role policy simplifies user management, and is a significant aspect of WLAN management. Use the (config-role-policy) instance to configure role policy related configuration commands. To navigate to the config-role instance, use the following commands: wm3400-34710C8(config)#role-policy <POLICY-NAME> wm3400-34710C8(config)#role-policy role1 wm3400-34710C8(config-role-policy-role1)# ? Role Policy Mode commands: default-role Configuration for Wireless Clients not matching any role no Negate a command or set its defaults user-role Create a role clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-role-policy-role1)#
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 982 role-policy The following table summarizes role policy commands default-role role-policy Assigns a default role to a wireless client that fails to find a matching role. Use this command to configure a wireless client not matching any role. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax default-role use [ip-access-list|mac-access-list] default-role use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1- 100> Command Description Reference default-role When a client fails to find a matching role, the default action is assigned to that client page 20-982 no Negates a command or sets its default page 20-984 user-role commands Creates a role and associates it to the newly created role policy page 20-987 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 983 default-role use mac-access-list [in|out] <MAC-ACCESS-LIST> precedence <1- 100> Parameters default-role use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1- 100> default-role use mac-access-list [in|out] MAC-ACCESS-LIST> precedence <1- 100> Example wm3400-34710C8(config-role-policy-test)#default-role use ip-access-list in test precedence 1 wm3400-34710C8(config-role-policy-test)#show context role-policy test default-role use ip-access-list in test precedence 1 wm3400-34710C8(config-role-policy-test)# default-role use Enables the configuration of a wireless client not matching any role Use Enables the use of an IP or a MAC access list ip-access-list [in|out] Enables the use of an IP access list in Applies the rule to incoming packets out Applies the rule to outgoing packets <IP-ACCESS-LIST> Specifies the IP access list <IP-ACCESS-LIST> Sets the IP access list name precedence <1-100> After specifying the IP access list, specify the access list precedence value. precedence Based on the packets received, the lower precedence value is evaluated first <1-100> Sets a precedence value from 1 - 100 default-role use Enables the configuration of a wireless client not matching any role Use Enables the use of an IP or MAC access list mac-access-list [in|out] Enables the use of a MAC access list in Applies the rule to incoming packets out Applies the rule to outgoing packets <MAC-ACCESS-LIST> Specifies the MAC access list <MAC-ACCESS-LIST> Sets the MAC access list name precedence <1-100> After specifying the MAC access list, specify the ACL precedence value. precedence Based on the packets received, the lower precedence value is evaluated first <1-100> Sets a precedence value from 1 - 100
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 984 Related Commands no role-policy Negates a command or resets settings to their default. When used in the config role policy mode, the no command removes the default role assigned to a wireless client. It also disables existing user roles from being assigned to new users. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [default-role|user-role] no default-role use [ip-access-list|mac-access-list] no default-role use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1- 100> no default-role use mac-access-list [in|out] <MAC-ACCESS-LIST> precedence <1-100> no user-role <ROLE> Parameters no default-role use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1- 100> no Removes the default role assigned to a client ip-access-list Creates a new IP based access list. Access lists control access to the network using a set of rules. Each rule specifies an action taken when a packet matches a given set of rules. If the action is deny, the packet is dropped. If the action is permit, the packet is allowed. no default-role use Removes the default role assigned to a wireless client Use Disables the use of an IP or MAC access list
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 985 no default-role use mac-access-list [in|out] <MAC-ACCESS-LIST> precedence <1-100> no user-role <ROLE> Example wm3400-34710C8(config-role-policy-test)#no default-role use ip-access-list in test precedence 1 wm3400-34710C8(config-role-policy-test)#show context role-policy test role role1 precedence 1 wm3400-34710C8(config-role-policy-test)# ip-access-list [in|out] Disables the use of an IP access list in Removes the rule applied to incoming packets out Removes the rule applied to outgoing packets <IP-ACCESS-LIST> Specifies the IP access list to remove <IP-ACCESS-LIST> Sets the IP access list name precedence <1-100> After specifying the IP access list, specify the ACL precedence value applied. precedence Based on the packets received, the lower precedence value is evaluated first. <1-100> Specify the precedence value from 1 - 100. no default-role use Removes the default role assigned to a wireless client Use Disables the use of an IP or MAC access list mac-access-list [in|out] Disables the use of a MAC access list in Removes the rule applied to incoming packets out Removes the rule applied to outgoing packets <MAC-ACCESS-LIST> Specifies the MAC access list to remove <MAC-ACCESS-LIST> Sets the MAC access list name precedence <1-100> After specifying the MAC access list to remove, specify the ACL precedence value applied. precedence Based on the packets received, the lower precedence value is evaluated first. <1-100> Specify the precedence value from 1 - 100. no user-role Deletes a user role <ROLE> Specify the user role name.
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 986 Related Commands user-role role-policy This command creates a user defined role and associates it to a role policy. This command defines a number of settings used to assign a user defined role to the role policy. user-role user-role Creates a user defined role. A user defined role configures a set of rules for this role. AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax user-role <ROLE-NAME> precedence <1-10000> Parameters user-role <ROLE-NAME> precedence <1-10000> default-role Assigns a default role to a wireless client user-role commands Creates a role and associates it to the newly created role policy user-role Creates a user defined role user-role commands Summarizes the user role commands user-role <ROLE-NAME> Configures the user defined role name <ROLE-NAME> Sets the user defined role name precedence <1-10000> Configures the rule precedence <1-10000> Sets the precedence for this role. If multiple roles match, then the role with the lower precedence number is selected.
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 987 Example wm3400-34710C8(config)#role-policy test wm3700-37FABE(config-role-policy-test)#show context role-policy test default-role use ip-access-list in test precedence 1 wm3400-34710C8(config-role-policy-test)#user-role testing precedence 10 wm3400-34710C8(config-role-policy-test-user-role-testing)# wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role testing precedence 10 default-role use ip-access-list in test precedence 1 Related Commands user-role commands role-policy The following table summarizes user role commands no Removes the user defined role assigned to a client Commands Description Reference ap-location Sets an APs deployment location page 20-988 authentication- type Selects an authentication type for a user role page 20-989 captive-portal Defines a captive portal role based filter page 20-990 encryption-type Selects the encryption type page 20-991 group Sets a group configuration for the role page 20-993 mu-mac Configures the client MAC addresses for the role based firewall page 20-994 no Negates a command or sets its default page 20-995 ssid Specifies a SSID page 20-998 use Defines the settings used with the role policy page 20-999 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 988 ap-location user-role commands Sets an APs deployment location Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ap-location [any|contains|exact|not-contains] ap-location any ap-location [contains|exact|not-contains] <WORD> Parameters ap-location any ap-location [contains|exact|not-contains] <WORD> Example wm3400-34710C8(config-role-policy-test-user-role-testing)#ap-location contains office wm3400-34710C8(config-role-policy-test-user-role-testing)# wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 ap-location contains office ap-location any Defines an APs location as any contains <WORD> Defines an AP location that contains a specified string <WORD> Sets a string to match exact <WORD> Defines an AP location that contains the exact specified string <WORD> Sets an exact string to match not-contains <WORD> Defines an AP location that does not contain the string <WORD> Sets a string that does not match the AP location
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 989 wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands authentication-type user-role commands Selects the authentication type for this user role Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication-type [any|eq|neq] authentication-type any authentication-type [eq|neq] [eap|kerberos|mac-auth|none] {(eap|kerberos|mac-auth|none)} Parameters authentication-type any no Removes an APs deployment location any The authentication type is any supported type
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 990 authentication-type [eq|neq] [eap|kerberos|mac-auth|none] {(eap|kerberos|mac-auth| none)} Example wm3400-34710C8(config-role-policy-test-user-role-testing)#authentication- type eq kerberos wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 authentication-type eq kerberos ap-location contains office wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands captive-portal user-role commands Defines captive portal based role filter for this user role eq [eap|kerberos|mac-auth| none] The authentication type equals one of the following types: eap Extensible authentication protocol kerberos Kerberos authentication mac-auth MAC authentication protocol none no authentication used These parameters are recursive, and you can configure more than one unique authentication type for this user role. neq [eap|kerberos| mac-auth|none] The authentication type does not match one or more of the following types: eap Extensible authentication protocol kerberos Kerberos authentication mac-auth MAC authentication protocol none no authentication used These parameters are recursive, and you can configure more than one unique not equal to authentication type for this user role. no Removes the authentication type configured for a user role
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 991 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax captive-portal authentication-state [any|post-login|pre-login] Parameters captive-portal authentication-state [any|post-login|pre-login] Example wm3400-34710C8(config-role-policy-test-user-role-testing)#captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 authentication-type eq kerberos ap-location contains office captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands encryption-type user-role commands Selects the encryption type for this user role. Encryption ensures privacy of all communication between access points and wireless clients. There are various modes of encrypting communication on a WLAN, such as Counter-model CBC-MAC Protocol (CCMP), Wired Equivalent Privacy (WEP), keyguard, Temporal Key Integrity Protocol (TKIP) etc. authentication-state Defines the authentication state of a client connecting to a captive portal any Specifies any authentication state post-login Specifies authentication is completed successfully pre-login Specifies authentication is pending no Removes captive portal based role filters configured for a user role
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 992 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax encryption-type [any|eq|neq] encryption-type any encryption-type [eq|neq] [ccmp|keyguard|none|tkip|wep128|wep64] {(ccmp|keyguard|none|tkip|tkip-ccmp|wep128|wep64)} Parameters encryption-type any encryption-type [eq|neq] [ccmp|keyguard|none|tkip|wep128|wep64] {(ccmp|keyguard|none|tkip|tkip-ccmp|wep128|wep64)} any The encryption type can be any one of the listed options eq [ccmp|keyguard|none|tkip| wep128|wep64] The encryption type equals one of the following options: ccmp: Encryption mode is CCMP keyguard: Encryption mode is keyguard. Keyguard encryption shields the master encryption keys from being discovered none: No encryption mode specified tkip: Encryption mode is TKIP wep128: Encryption mode is WEP128 wep64: Encryption mode is WEP64 These parameters are recursive, and you can configure more than one encryption type for this user role.
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 993 Example wm3400-34710C8(config-role-policy-test-user-role-testing)#encryption-type eq wep128 wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 authentication-type eq kerberos encryption-type eq wep128 ap-location contains office captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands group user-role commands Configures a group for this user role Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax group [any|contains|exact|not-contains] neq[ccmp|keyguard|none|tkip| wep128|wep64] The encryption type is not equal to any of the following options: ccmp: Encryption mode is not equal to CCMP keyguard: Encryption mode is not equal to keyguard none: Encryption mode is not equal to none tkip: Encryption mode is not equal to TKIP wep128: Encryption mode is not equal to WEP128 wep64: Encryption mode is not equal to WEP64 These parameters are recursive, and you can configure more than one not equal to encryption type for this user role. no Removes the encryption type configured for this user role
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 994 group any group [contains|exact|not-contains] <WORD> Parameters group any group [contains|exact|not-contains] <WORD> Example wm3400-34710C8(config-role-policy-test-user-role-testing)#group any wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands mu-mac user-role commands Configures a clients MAC addresses for the role based firewall any This user role can fit into any group contains <WORD> Configures this user role with a group that contains the specified string <WORD> Enter the string to match against. This is case sensitive, and is compared against the group name returned by the RADIUS server. exact <WORD> Configures this user role with a group that contains the exact specified string <WORD> Enter the exact string to match against. This is case sensitive, and is compared against the group name returned by the RADIUS server. not-contains <WORD> Configures this user role with a group that does not contain the specified string <WORD> Enter the string to match against. This is case sensitive, and is compared against the group name returned by the RADIUS server. no Removes the group configured for a user role
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 995 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax mu-mac [<MAC>|any] mu-mac any mu-mac <MAC> {mask <MAC>} Parameters mu-mac any mu-mac <MAC> {mask <MAC>} Example wm3400-34710C8(config-role-policy-test-user-role-testing)#mu-mac any wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands no user-role commands Negates a command or resets configured settings to their default. When used in the config role policy user role mode, the no command removes or resets settings, such as AP location, authentication type, encryption type, captive portal etc. any Matches a wireless client with any MAC address <MAC> Matches a specific MAC address with the allowed wireless client <MAC> Sets the MAC address in the AA-BB-CC-DD-EE-FF format mask <MAC> Optional. After specifying the clients MAC address, specify the mask in the AA-BB-CC-DD-EE-FF format. no Removes the MAC address and mask for this user role
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 996 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [ap-location|authentication-type|captive-portal|encryption-type|group| mu-mac|ssid|use] no [ap-location|authentication-type|encryption-type|group|mu-mac|ssid] no captive-portal authentication-state no use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1-100> no use mac-access-list [in|out] <MAC-ACCESS-LIST> precedence <1-100> Parameters no [ap-location|authentication-type|encryption-type|group|mu-mac|ssid] no captive-portal authentication-state no use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1-100> no ap-location Removes a APs deployment location no authentication-type Removes the authentication type configured for a user role no encryption-type Removes the encryption type configured for a user role no group Removes the group configured for a user role no mu-mac Removes the MAC address and mask configured for a user role no ssid Removes the SSID configured for a user role no captive-portal Removes the captive portal based role filter configured for a user role authentication-state Reverts the authentication state to default no use Removes an IP or MAC access list from being used with this user role ip-access-list [in|out] Removes the IP access list in Removes the list from being applied to incoming packets out Removes the list from being applied to outgoing packets <IP-ACCESS-LIST> Specifies the IP access list name
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 997 no use mac-access-list [in|out] MAC-ACCESS-LIST> precedence <1-100> Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example The Role Policy User Role configuration before the execution of the no command: wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 authentication-type eq kerberos encryption-type eq wep128 ap-location contains office captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)# The Role Policy User Role configuration after the execution of the no command: wm3400-34710C8(config-role-policy-test-user-role-testing)#no authentication-type wm3400-34710C8(config-role-policy-test-user-role-testing)# wm3400-34710C8(config-role-policy-test-user-role-testing)#no encryption- type wm3400-34710C8(config-role-policy-test-user-role-testing)# wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 ap-location contains office captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)# precedence <1-100> Removes the access list precedence <1-100> Specifies the precedence from 1 - 100 no use Removes an IP or MAC access list used with this user role mac-access-list [in|out] Removes the Mac access list in Removes the list from being applied to incoming packets out Removes the list from being applied to outgoing packets <MAC-ACCESS-LIST> Specifies the MAC access list name precedence <1-100> Removes the access list precedence <1-100> Specifies the precedence from 1 - 100
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 998 Related Commands ssid user-role commands Configures a user role SSID Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ssid [any|exact|contains|not-contains] ssid any ssid [exact|contains|not-contains] <WORD> Parameters ssid any ssid [exact|contains|not-contains] <WORD> ap-location Sets an APs deployment location authentication-type Selects the authentication type for a user role captive-portal Defines a captive portal based role filter for a user role encryption-type Selects the encryption type used for a user role group Configures a group for a user role mu-mac Configures the clients MAC addresses for the role based firewall ssid Configures a user role SSID use Defines the access list settings used with a user role ssid any Specifies the SSID can be any value ssid exact <WORD> Specifies the SSID exactly matches the specified string <WORD> Specify the SSID to match. The SSID is case sensitive and is compared against the SSID configured for the WLAN.
role-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 999 Example wm3400-34710C8(config-role-policy-test-user-role-testing)#ssid not-contains TESTSSID wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 ssid not-contains TESTSSID captive-portal authentication-state pre-login wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands use user-role commands Defines the access list settings used with this user role Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax use [ip-access-list|mac-access-list] use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1-100> use mac-access-list [in|out] <MAC-ACCESS-LIST> precedence <1-100> ssid contains <WORD> Specifies the SSID contains the specified string <WORD> Specify the SSID to match. The SSID is case sensitive and is compared against the SSID configured for the WLAN. ssid not-contains <WORD> Specifies the SSID does not contain the specified string <WORD> Specify the SSID to match. The SSID is case sensitive and is compared against the SSID configured for the WLAN. no Removes the SSID configured for a user role
Chapter 20: Role Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1000 Parameters use ip-access-list [in|out] <IP-ACCESS-LIST> precedence <1-100> use mac-access-list [in|out] MAC-ACCESS-LIST> precedence <1-100> Example wm3400-34710C8(config-role-role1)#use ip-access-list in test precedence 9 wm3400-34710C8(config-role-policy-test-user-role-testing)#show context user-role role1 precedence 1 ssid not-contains TESTSSID captive-portal authentication-state pre-login use ip-access-list in test precedence 9 wm3400-34710C8(config-role-policy-test-user-role-testing)# Related Commands ip-access-list [in|out] Uses an IP access list with this user role in Applies rule to incoming packets out Applies rule to outgoing packets <IP-ACCESS-LIST> Defines the IP access list name precedence <1-100> After specifying the name of the access list, specify the precedence applied to it. Based on the packets received, a lower precedence value is evaluated first <1-100> Sets a precedence from 1 - 100 mac-access-list [in|out] Uses a MAC access list with this user role in Applies rule to incoming packets out Applies rule to outgoing packets <MAC-ACCESS-LIST> Defines the MAC access list name precedence <1-100> After specifying the name of the access list, specify the precedence applied to it. Based on the packets received, a lower precedence value is evaluated first <1-100> Sets a precedence from 1 - 100 no Removes an IP or MAC access list from use with a user role
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1001 C H A P T E R 21 Smart RF Policy This chapter summarizes Smart RF policy commands within the CLI structure. A Self Monitoring at Run Time RF Management (Smart RF) policy defines operating and recovery parameters that can be assigned to groups of access points. A Smart RF policy is designed to scan the network to identify the best channel and transmit power for each access point radio. Use the (config) instance to configure Smart RF Policy related configuration commands. To navigate to the Smart RF policy instance, use the following commands: wm3400-34710C8(config)#smart-rf-policy <POLICY-NAME> wm3400-34710C8(config)#smart-rf-policy test wm3400-34710C8(config-smart-rf-policy-test)#? Smart RF Mode commands: assignable-power Specify the assignable power during power- assignment auto-assign-sensor Allow smart-rf to select optimal sensor radios for wips and unauthorized ap detection channel-list Select channel list for smart-rf channel-width Select channel width for smart-rf coverage-hole-recovery Recover from coverage hole enable Enable this smart-rf policy group-by Configure grouping parameters interference-recovery Recover issues due to excessive noise and interference neighbor-recovery Recover issues due to faulty neighbor radios no Negate a command or set its defaults sensitivity Configure smart-rf sensitivity (Modifies various other smart-rf configuration items) smart-ocs-monitoring Smart off channel scanning clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1002 wm3400-34710C8(config-smart-rf-policy-test)# smart-rf-policy Smart RF Policy The following table summarizes Smart RF policy commands assignable-power smart-rf-policy Command Description Reference assignable- power Specifies the power range during power assignment page 21-1002 auto-assign- sensor Allows Smart RF to select optimal sensor radios for WIPS and unauthorized AP detection page 21-1003 channel-list Assigns the channel list for the selected frequency page 21-1004 channel-width Selects the channel width for Smart RF configuration page 21-1005 coverage-hole- recovery Enables recovery from errors page 21-1007 enable Enables a Smart RF policy page 21-1008 group-by Configures grouping parameters page 21-1009 interference- recovery Recovers issues due to excessive noise and interference page 21-1010 neighbor- recovery Enables recovery from errors due to faulty neighbor radios page 21-1012 no Negates a command or sets its default values page 21-1014 sensitivity Configures Smart RF sensitivity page 21-1016 smart-ocs- monitoring Applies smart off channel scanning instead of dedicated detectors page 21-1017 smart-ocs- monitoring Enables automatic channel selection on an AP4700 series device. page 21-1020 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1003 Specifies the power range during power assignment AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax assignable-power [2.4GHz|5GHz] [max|min] <1-20> Parameters assignable-power [2.4GHz|5GHz] [max|min] <1-20> Example wm3400-34710C8(config-smart-rf-policy-test)#assignable-power 5GHz max 20 wm3400-34710C8(config-smart-rf-policy-test)#assignable-power 5GHz min 8 wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test assignable-power 5GHz min 8 assignable-power 5GHz max 20 Related Commands auto-assign-sensor smart-rf-policy Allows Smart RF to select optimal sensor radios for WIPS and unauthorized AP detection. Enable sensor radios for real time monitoring and self healing when needed. These sensor radios are dedicated to monitoring activities only and do not provide client services. 2.4GHz [max|min] <1-20> Assigns a power range on the 2.4GHz band max <1-20> Sets the upper limit in the range from 1 - 20 dBm min <1-20> Sets the lower limit in the range from 1 - 20 dBm 5GHz [max|min] <1-20> Assigns a power range on the 5GHz band max <1-20> Sets the upper limit in the range from 1 - 20 dBm min <1-20> Sets the lower limit in the range from 1 - 20 dBm no Resets assignable power to its default
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1004 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Parameters None Example wm3400-34710C8(config-smart-rf-policy-test)#auto-assign-sensor wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor assignable-power 5GHz min 8 assignable-power 5GHz max 20 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands channel-list smart-rf-policy Assigns the channel list for the selected frequency no Disables auto assignment of sensor radios on this Smart RF policy
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1005 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax channel-list [2.4GHz|5GHz] <WORD> Parameters channel-list [2.4GHz|5GHz] <WORD> Example wm3400-34710C8(config-smart-rf-policy-test)#channel-list 2.4Ghz 1,12 wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands channel-width smart-rf-policy Selects the channel width for Smart RF configuration 2.4GHz <WORD> Assigns a channel list for the 2.4GHz band <WORD> Sets a comma separated list of channels 5GHz <WORD> Assigns a channel list for the 5GHz band <WORD> Sets a comma separated list of channels no Resets the channel list for the selected frequency to its default
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1006 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax channel-width [2.4GHz|5GHz] [20MHz|40MHz|auto] Parameters channel-width [2.4GHz|5GHz] [20MHz|40MHz|auto] Example wm3400-34710C8(config-smart-rf-policy-test)#channel-width 5 auto wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto wm3400-34710C8(config-smart-rf-policy-test)# 2.4GHz [20MHz|40MHz| auto] Assigns the channel width for the 2.4GHz band 20MHz Assigns the 20MHz channel width 40MHz Assigns the 40MHz channel width auto Assigns the best possible channel in the 20MHz or 40MHz channel width 5GHz [20MHz|40MHz| auto] Assigns the channel width for the 5GHz band 20MHz Assigns the 20MHz channel width 40MHz Assigns the 40MHz channel width auto Assigns the best possible channel in the 20MHz or 40MHz channel width
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1007 Related Commands coverage-hole-recovery smart-rf-policy Enables recovery from coverage hole errors detected by Smart RF Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax coverage-hole-recovery {client-threshold|coverage-interval|interval|snr- threshold} coverage-hole-recovery {client-threshold [2.4GHz|5GHz] <1-255>} coverage-hole-recovery {{coverage-interval|interval} [2.4GHz|5GHz] [<1- 120>]} coverage-hole-recovery {snr-threshold [2.4Ghz|5Ghz] <1-75>} Parameters coverage-hole-recovery {client-threshold [2.4GHz|5GHz] <1-255>} no Resets channel width for the selected frequency to its default client-threshold Optional. Specifies the minimum number of clients below Signal-to-Noise Ratio (SNR) threshold required to trigger coverage hole recovery 2.4GHz <1-255> Specifies the minimum number of clients on the 2.4GHz band <1-255> Sets a value from 1 - 255. The default is 1. 5GHz <1-255> Specifies the minimum number of clients on the 5GHz band <1-255> Sets a value from1 - 255. The default is 1.
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1008 coverage-hole-recovery {{coverage-interval|interval} [2.4GHz|5GHz] [<1- 120>]} coverage-hole-recovery {snr-threshold [2.4Ghz|5Ghz] <1-75>} Example wm3400-34710C8(config-smart-rf-policy-test)#coverage-hole-recovery snr- threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto sensitivity custom coverage-hole-recovery snr-threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands enable smart-rf-policy Enables a Smart RF policy coverage-interval Optional. Specifies the interval coverage hole recovery is performed after coverage hole is detected interval Optional. Specifies the interval coverage hole recovery is performed before coverage hole is detected 2.4GHz <1-120> Specifies coverage hole recovery interval on the 2.4GHz band <1-120> Sets a value from 1 - 120 seconds. The default is 10 seconds. 5GHz <1-120> Specifies coverage hole recovery interval on the 5GHz band <1-120> Sets a value from 1 - 120 seconds. The default is 10 seconds. snr-threshold Optional. Specifies the SNR threshold value. This value is the signal to noise ratio threshold for an associated client as seen by its associated AP radio. When the SNR threshold is exceeded, the radio increases its transmit power to increase the coverage for the associated client. 2.4GHz <1-75> Specifies SNR threshold on the 2.4GHz band <1-75> Sets a value from 1 - 75. The default is 20dB. 5GHz <1-75> Specifies SNR threshold on the 5GHz band <1-75> Sets a value from 1 - 75. The default is 20dB. no Disables recovery from coverage hole errors
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1009 Use this command to enable this Smart RF policy. Once enabled, the policy can be assigned to a RF Domain or used for wireless controller network support. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax enable Parameters None Example wm3400-34710C8(config-smart-rf-policy-test)#enable wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto sensitivity custom coverage-hole-recovery snr-threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)# Related Commands group-by smart-rf-policy Configures Smart RF grouping values no Disables a Smart RF policy
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1010 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax group-by [area|floor] Parameters group-by [area|floor] Example wm3400-34710C8(config-smart-rf-policy-test)#group-by floor wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor group-by floor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto sensitivity custom coverage-hole-recovery snr-threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands interference-recovery smart-rf-policy area Configures a group based on area floor Configures a group based on floor no Removes Smart RF group settings
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1011 Recovers excessive noise and interference. Enabling interference recovery ensures that noise levels and other RF parameters are continuously monitored on a radios current channel. When noise levels exceed the specified noise threshold, Smart RF switches to another channel with less interference. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax interference-recovery {channel-hold-time|channel-switch-delta|client- threshold| interference|noise|noise-factor} interference-recovery {channel-switch-delta [2.4GHz|5GHZ] [<5-35>]} interference-recovery {channel-hold-time [<0-86400>]|client-threshold [<1- 255>]| interference|noise|noise-factor [<1.0-3.0>]} Parameters interference-recovery {channel-switch-delta [2.4GHz|5GHZ] [<5-35>]} interference-recovery {channel-hold-time [<0-86400>]|client-threshold [<1- 255>]| interference|noise|noise-factor [<1.0-3.0>]} channel-switch-delta Optional. Specifies the difference between the current and best channel interference for a channel change [2.4GHz|5GHz] Selects the band 2.4GHz Selects the 2.4GHz band 5GHz Selects the 5GHz band <5-35> Specifies the difference between the current and best channel interference <5-35> Sets a value from 5 - 35 dBm channel-hold-time <0-86400> Optional. Defines the minimum time between two channel change recoveries <0-86400> Sets the time between channel change assignments based on interference or noise in seconds client-threshold <1-255> Optional. Specifies client thresholds to avoid channel changes (when exceeded). <1-255> Sets the number of clients from 1 - 255
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1012 Example wm3400-34710C8(config-smart-rf-policy-test)#interference-recovery channel- switch-delta 5 5 wm3400-34710C8(config-smart-rf-policy-test)#interference-recovery interference wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor group-by floor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto sensitivity custom coverage-hole-recovery snr-threshold 5GHz 1 interference-recovery channel-switch-delta 5GHz 5 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands neighbor-recovery smart-rf-policy Enables recovery from errors due to faulty neighbor radios. Enabling neighbor recovery ensures automatic recovery when a radio fails within the radio coverage area. Smart RF instructs neighboring access points to increase their transmit power to compensate for the failed radio. interference Optional. Considers external interference values to perform interference recovery noise Optional. Considers noise values to perform interference recovery noise-factor <1.0-3.0> Optional. Configures additional noise factor for non-wifi interference <1.0-3.0> Sets a noise factor from 1.0 - 3.0 no Disables recovery from excessive noise and interference
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1013 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax neighbor-recovery {dynamic-sampling|power-hold-time|power-threshold} neighbor-recovery {dynamic-sampling {retries [<1-10>]|threshold [<1-30>]}} neighbor-recovery {power-hold-time [<0-3600>]} neighbor-recovery {power-threshold [2.4Ghz|5Ghz] [<-85--55>]} Parameters neighbor-recovery {dynamic-sampling {retries [<1-10>]|threshold [<1-30>]}} neighbor-recovery {power-hold-time [<0-3600>]} neighbor-recovery {power-threshold [2.4Ghz|5Ghz] [<-85--55>]} dynamic-sampling Optional. Configures dynamic sampling on this Smart RF policy retries <1-10> Optional. Specifies the number of retries before allowing a power change <1-10> Sets the number of retries from 1 - 10 threshold <1-30> Optional. Specifies the minimum number of sample reports before which a power change requires dynamic sampling <1-30> Sets the minimum number of reports from 1 - 30 power-hold-time Optional. Specifies the minimum time between two power change recoveries <0-3600> Sets the time from 0 - 3600 seconds power-threshold Optional. Specifies the power threshold based on the recovery performed [2.4GHz|5GHz] Selects the band 2.4GHz Selects the 2.4GHz band 5GHz Selects the 5GHz band <-85--55> Specify the threshold value <-85--55> Sets the power threshold from -85 - -55 dBm
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1014 Example wm3400-34710C8(config-smart-rf-policy-test)#neighbor-recovery power- threshold 2.4 -82 wm3400-34710C8(config-smart-rf-policy-test)#neighbor-recovery power- threshold 5 -65 wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test auto-assign-sensor group-by floor assignable-power 5GHz min 8 assignable-power 5GHz max 20 channel-list 2.4GHz 1,12 channel-width 5GHz auto sensitivity custom interference-recovery channel-switch-delta 5GHz 5 neighbor-recovery power-threshold 5GHz -65 neighbor-recovery power-threshold 2.4GHz -82 coverage-hole-recovery snr-threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands no smart-rf-policy Negates a command or sets its default. When used in the config Smart RF policy mode, the no command disables or resets Smart RF settings. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [assignable-power|auto-assign-sensor|channel-list|channel-width| coverage-hole-recovery|enable|group-by|interference-recovery| neighbor-recovery| smart-ocs-monitoring] no Disables recovery from faulty neighbor radios
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1015 Parameters no [assignable-power|auto-assign-sensor|channel-list|channel-width| coverage-hole-recovery|enable|group-by|interference-recovery|neighbor- recovery| smart-ocs-monitoring] Example The following is the Smart RF policy settings before the execution of the no command: wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test group-by floor sensitivity custom interference-recovery channel-switch-delta 5GHz 5 neighbor-recovery power-threshold 5GHz -65 neighbor-recovery power-threshold 2.4GHz -82 coverage-hole-recovery snr-threshold 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# wm3400-34710C8(config-smart-rf-policy-test)#no interference-recovery channel-switch-delta 5GHz wm3400-34710C8(config-smart-rf-policy-test)#no neighbor-recovery power- threshold 2.4GHz wm3400-34710C8(config-smart-rf-policy-test)#no neighbor-recovery power- threshold 5GHz The following is the Smart RF policy settings after the execution of the no command: wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test rwm3400-34710C8(config-smart-rf-policy-test)# no assignable-power Resets assignable power to its default no auto-assign-sensor Disables auto assignment of sensor radios to its default no channel-list Resets the channel list for the selected frequency to its default no channel-width Resets channel width for the selected frequency to its default no coverage-hole-recovery Disables recovery from coverage hole errors no enable Disables a Smart RF policy no group-by Removes a Smart RF policys group settings no interference-recovery Disables recovery from errors due to excessive noise and interference no neighbor-recovery Disables recovery from errors due to faulty neighbor radios no smart-ocs-monitoring Disables off channel monitoring When used on an AP4700 seroes model access point, this command disables a meshpoint.
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1016 Related Commands sensitivity smart-rf-policy Configures Smart RF sensitivity Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax sensitivity [custom|high|low|medium] Parameters sensitivity [custom|high|low|medium] assignable-power Assigns the power range auto-assign-sensor Allows Smart RF to automatically select optimal sensor radios for WIPS and unauthorized AP detection channel-list Assigns the channel list for the selected frequency channel-width Selects the channel width for Smart RF configuration coverage-hole-recovery Enables recovery from coverage hole errors enable Enables the configured Smart RF policy features group-by Configures grouping parameters on this Smart RF policy interference-recovery Enables recovery of errors due to excessive noise and interference neighbor-recovery Enables recovery of faulty neighbor radios smart-ocs-monitoring Applies smart off channel scanning instead of dedicated detectors smart-ocs-monitoring Applies smart off channel scanning instead of dedicated detectors When used on an AP4700 series model, this command configures a radio meshpoint on the selected band. sensitivity Configures Smart RF sensitivity levels custom Custom sensitivity Enables interference recovery, coverage hole recovery, and neighbor recovery as additional Smart RF options
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1017 Example wm3400-34710C8(config-smart-rf-policy-test)#sensitivity high smart-rf-policy test sensitivity high smart-ocs-monitoring frequency 5GHz 3 smart-ocs-monitoring frequency 2.4GHz 3 smart-ocs-monitoring sample-count 2.4GHz 3 smart-ocs-monitoring extended-scan-frequency 5GHz 0 smart-ocs-monitoring extended-scan-frequency 2.4GHz 0 interference-recovery client-threshold 255 interference-recovery channel-switch-delta 5GHz 5 interference-recovery channel-switch-delta 2.4GHz 5 neighbor-recovery power-threshold 5GHz -65 neighbor-recovery power-threshold 2.4GHz -65 no coverage-hole-recovery coverage-hole-recovery coverage-interval 5GHz 5 coverage-hole-recovery coverage-interval 2.4GHz 5 coverage-hole-recovery client-threshold 5GHz 0 coverage-hole-recovery client-threshold 2.4GHz 0 interference-recovery channel-hold-time 180 smart-ocs-monitoring smart-rf-policy Applies smart Off Channel Scanning (OCS) instead of dedicated detectors Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax smart-ocs-monitoring {client-aware|extended-scan-frequency|frequency| off-channel-duration|power-save-aware|sample-count|voice-aware} high High sensitivity low Low sensitivity medium Medium sensitivity. This is the default setting.
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1018 smart-ocs-monitoring {client-aware [2.4GHz|5GHz] [<1-255>]} smart-ocs-monitoring {extended-scan-frequency [2.4GHz|5GHz] [<0-50>]} smart-ocs-monitoring {frequency [2.4GHz|5GHz] [<1-120>]} smart-ocs-monitoring {off-channel-duration [2.4GHz|5GHz] [<20-150>]} smart-ocs-monitoring {power-save-aware [2.4GHz|5GHz] [dynamic|strict]} smart-ocs-monitoring {sample-count [2.4GHz|5GHz] [<1-15>]} smart-ocs-monitoring {voice-aware [2.4GHz|5GHz] [dynamic|strict]} Parameters smart-ocs-monitoring {client-aware [2.4GHz|5GHz] [<1-255>]} smart-ocs-monitoring {extended-scan-frequency [2.4GHz|5GHz] [<0-50>]} smart-ocs-monitoring {frequency [2.4GHz|5GHz] [<1-120>]} client-aware Optional. Enables client aware scanning on this Smart RF policy Use this parameter to configure a client threshold number. When the number of clients connected to a radio equals this threshold number, the radio does not change its channel even if needed (based on the interference recovery determination made by the smart master) 2.4GHz <1-255> Enables client aware scanning on the 2.4GHz band Avoids radio scanning when a specified minimum number of clients are present <1-255> Sets the minimum number of clients from 1 - 255. The default is 50 clients. 5GHz <1-255> Enables client aware scanning on the 5GHz band Avoids radio scanning when a specified minimum number of clients are present <1-255> Sets the minimum number of clients from 1 - 255. The default is 50 clients. extended-scan-frequency Optional. Enables an extended scan, as opposed to a neighbor only scan, on this Smart RF policy. This is the frequency radios use to scan for non-peer radios 2.4GHz <0-50> Enables extended scan on the 2.4GHz band <0-50> Sets the number of trails from 0 - 50. The default is 5. 5GHz <0-50> Enables extended scan on the 5GHz band <0-50> Sets the number of trails from 0 - 50. The default is 5. frequency Optional. Specifies the frequency the channel must be switched. Sets the value, in seconds, from 1 - 120 2.4GHz <1-20> Selects the 2.4GHz band <1-20> Sets a scan frequency from 1 - 120 seconds. The default is 6 seconds.
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1019 smart-ocs-monitoring {off-channel-duration [2.4GHz|5GHz] [<20-150>]} smart-ocs-monitoring {power-save-aware [2.4GHz|5GHz] [dynamic|strict]} smart-ocs-monitoring {sample-count [2.4GHz|5GHz] [<1-15>]} smart-ocs-monitoring {voice-aware [2.4GHz|5GHz] [dynamic|strict]} 5GHz <1-20> Selects the 5GHz band <1-20> Sets a scan frequency from 1 - 120 seconds. The default is 6 seconds. off-channel-duration Optional. Specifies the duration to scan off channel This is the duration access point radios use to monitor devices within the network and, if necessary, perform self healing and neighbor recovery to compensate for coverage area losses within a RF Domain. 2.4GHz <20-150> Selects the 2.4GHz band <20-150> Sets the off channel duration from 20 - 150 milliseconds. The default is 50 milliseconds. 5GHz <20-150> Selects the 5GHz band <20-150> Sets the off channel duration from 20 - 150 milliseconds. The default is 50 milliseconds. power-save-aware Optional. Enables power save aware scanning on this Smart RF policy 2.4GHz [dynamic|strict] Sets power save aware scanning mode on the 2.4GHz band dynamic Dynamically avoids scanning based on traffic for power save (PSP) clients strict Strictly avoids scanning when PSP clients are present 5GHz [dynamic|strict] Sets power save aware scanning mode on the 5GHz band dynamic Dynamically avoids scanning based on traffic for PSP clients strict Strictly avoids scanning when PSP clients are present sample-count Optional. Specifies the number of samples to collect before reporting an issue to the smart master 2.4GHz <1-15> Selects the 2.4GHz band <1-15> Specifies the number of samples to collect from 1 - 15. The default is 5. 5GHz <1-15> Selects the 5GHz band <1-15> Specifies the number of samples to collect from 1 - 15. The default is 5. voice-aware Optional. Enables voice aware scanning on this Smart RF policy 2.4Ghz [dynamic|strict] Specifies the scanning mode on the 2.4GHz band dynamic Dynamically avoids scanning based on traffic for voice clients strict Strictly avoids scanning when voice clients are present The default is dynamic.
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1020 Example wm3400-34710C8(config-smart-rf-policy-test)#smart-ocs-monitoring extended- scan-frequency 2.4Ghz 9 wm3400-34710C8(config-smart-rf-policy-test)#smart-ocs-monitoring sample- count 2.4Ghz 3 wm3400-34710C8(config-smart-rf-policy-test)#smart-ocs-monitoring off- channel-duration 2.4Ghz 25 wm3400-34710C8(config-smart-rf-policy-test)#show context smart-rf-policy test sensitivity custom smart-ocs-monitoring off-channel-duration 2.4GHz 25 smart-ocs-monitoring sample-count 2.4GHz 3 smart-ocs-monitoring extended-scan-frequency 2.4GHz 9 smart-ocs-monitoring client-aware 5GHz 1 wm3400-34710C8(config-smart-rf-policy-test)# Related Commands smart-ocs-monitoring smart-rf-policy Enables automatic channel selection on an AP4700 series model access point, provided radio meshpoint is configured. Use this command to configure meshpoint on an AP4700 series access point. Supported on the following platforms: AP4700 Syntax smart-ocs-monitoring {client-aware|extended-scan- frequency|frequency|meshpoint| off-channel-duration|power-save-aware|sample-count|voice-aware} smart-ocs-monitoring {client-aware [2.4GHz|5GHz] [<1-255>]} smart-ocs-monitoring {extended-scan-frequency [2.4GHz|5GHz] [<0-50>]} smart-ocs-monitoring {frequency [2.4GHz|5GHz] [<1-120>]} smart-rf-monitoring {meshpoint [2.4GHz|4.9GHz|5GHz]} 5Ghz [dynamic|strict] Specifies the scanning mode on the 5GHz band dynamic Dynamically avoids scanning based on traffic for voice clients strict Strictly avoids scanning when voice clients are present. The default is dynamic. no Disables off channel monitoring
smart-rf-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1021 smart-rf-monitoring {meshpoint [2.4GHz <MESHPOINT-NAME>|4.9GHz <MESHPOINT- NAME>| 5GHz <MESHPOINT-NAME>]} smart-ocs-monitoring {off-channel-duration [2.4GHz|5GHz] [<20-150>]} smart-ocs-monitoring {power-save-aware [2.4GHz|5GHz] [dynamic|strict]} smart-ocs-monitoring {sample-count [2.4GHz|5GHz] [<1-15>]} smart-ocs-monitoring {voice-aware [2.4GHz|5GHz] [dynamic|strict]} Parameters This section documents only the meshpoint feature of the smart-ocs-monitoring command. For other parameter details, see smart-ocs-monitoring. smart-rf-monitoring {meshpoint [2.4GHz <MESHPOINT-NAME>|4.9GHz <MESHPOINT- NAME>| 5GHz <MESHPOINT-NAME>]} Example AP4700-0E3B54(config-smart-rf-policy-smart-7161)#smart-ocs-monitoring meshpoint 2.4GHz meshpoint-name AP4700-0E3B54(config-smart-rf-policy-smart-7161)#show context smart-rf-policy smart-7161 smart-ocs-monitoring meshpoint 5GHz meshpoint-name smart-ocs-monitoring meshpoint 4.9GHz meshpoint-name smart-ocs-monitoring meshpoint 2.4GHz meshpoint-name Related Commands meshpoint Optional. Configures a meshpoint on an AP4700 2.4GHz <MESHPOINT-NAME> Configures the meshpoint on the 2.4GHz band <MESHPOINT-NAME> Sets the meshpoint name 4.9GHz <MESHPOINT-NAME> Configures the meshpoint on the 4.9GHz band <MESHPOINT-NAME> Sets the meshpoint name 5GHz <MESHPOINT-NAME> Configures the meshpoint on the 5GHz band <MESHPOINT-NAME> Sets the meshpoint name no Disables a radio meshpoint configured on an AP4700 series access point
Chapter 21: Smart RF Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1022
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1023 C H A P T E R 22 WIPS Policy This chapter summarizes WIPS policy commands in detail. The Wireless Intrusion Protection Systems (WIPS) is an additional measure of security designed to continuously monitor the network for threats and intrusions. Along with wireless VPNs, encryptions and authentication policies, WIPS enhances the security of a WLAN. The wireless controller supports WIPS through the use of sensor devices that locate unauthorized access points. Use the (config) instance to configure WIPS policy commands. To navigate to the WIPS policy instance, use the following commands: wm3400-34710C8(config)#wips-policy <POLICY-NAME> wm3400-34710C8(config)#wips-policy test wm3400-34710C8(config-wips-policy-test)#? Wips Policy Mode commands: ap-detection Rogue AP detection enable Enable this wips policy event Configure an event history-throttle-duration Configure the duration for which event duplicates are not stored in history no Negate a command or set its defaults signature Signature to configure use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-wips-policy-test)#
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1024 wips-policy WIPS Policy The following table summarizes WIPS policy commands ap-detection wips-policy Enables the detection of unauthorized or unsanctioned APs. Unauthorized APs are untrusted access points connected to an access point managed network. These untrusted APs accept wireless client associations. It is important to detect such rogue APs and declare them unauthorized. Command Description Reference ap-detection Defines the WIPS AP detection configuration page 22-1024 enable Enables a WIPS policy page 22-1025 event Configures events page 22-1026 history-throttle- duration Configures the duration event duplicates are omitted from the event history page 22-1030 no Negates a command or sets its default page 22-1031 signature Configures signature page 22-1035 use Defines a WIPS policy settings page 22-1049 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1025 AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax ap-detection {ageout|wait-time} ap-detection {age-out [<30-86400>]|wait-time [<10-600>]} Parameters ap-detection {age-out [<30-86400>]|wait-time [<10-600>]} Example wm3400-34710C8(config-wips-policy-test)#ap-detection wait-time 15 wm3400-34710C8(config-wips-policy-test)#ap-detection age-out 50 wm3400-34710C8(config-wips-policy-test)#show context wips-policy test ap-detection-ageout 50 ap-detection-wait-time 15 wm3400-34710C8(config-wips-policy-test)# Related Commands enable wips-policy Associates this WIPS policy with a wireless controller profile age-out <30-86400> Optional. Configures the unauthorized AP ageout interval. The WIPS policy uses this value to ageout unauthorized APs. <30-86400> Sets an ageout interval from 30 - 86400 seconds. The default is 5 minutes (300 seconds). wait-time <10-600> Optional. Configures the wait time before a detected AP is declared as unauthorized <10-600> Sets a wait time from 10 - 600 seconds. The default is 1 minute (60 seconds). no Disables the detection of unauthorized or unsanctioned APs
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1026 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax enable Parameters None Example wm3400-34710C8(config-wips-policy-test)#enable wm3400-34710C8(config-wips-policy-test)# Related Commands event wips-policy Configures events, filters and threshold values for this WIPS policy. Events have been grouped into three categories, AP anomaly, client anomaly, and excessive. WLANs are baselined for matching criteria. Any deviation from this baseline is considered an anomaly and logged as an event. no Disables a WIPS policy from use with a wireless controller profile
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1027 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax event [ap-anomaly|client-anomaly|enable-all-events|excessive] event ap-anomaly [ad-hoc-violation|airjack|ap-ssid-broadcast-in-beacon| asleap|impersonation-attack|null-probe-response| transmitting-device-using-invalid-mac|unencrypted-wired-leakage| wireless-bridge] event client-anomaly [crackable-wep-iv-key-used|dos-broadcast-deauth| fuzzing-all-zero-macs|fuzzing-invalid-frame-type|fuzzing-invalid- mgmt-frames| fuzzing-invalid-seq-num|identical-src-and-dest-addr|invalid-8021x- frames| netstumbler-generic|non-changing-wep-iv|tkip-mic-counter- measures|wellenreiter] {filter-ageout [<0-86400>]} event enable-all-events event excessive [80211-replay-check-failure|aggressive-scanning| auth-server-failures|decryption-failures|dos-assoc-or-auth-flood| dos-eapol-start-storm |dos-unicast-deauth-or-disassoc|eap-flood| eap-nak-flood|frames-from-unassoc-station] {filter-ageout [<0- 86400>]| threshold-client [<0-65535>]|threshold-radio [<0-65535>]} Parameters event ap-anomaly [ad-hoc-violation|airjack|ap-ssid-broadcast-in-beacon| asleap|impersonation-attack|null-probe-response| transmitting-device-using-invalid-mac|unencrypted-wired-leakage|wireless- bridge] ap-anomaly Enables AP anomaly event tracking An AP anomaly event refers to suspicious frames sent by neighboring APs. ad-hoc-violation Tracks adhoc network violations airjack Tracks AirJack attacks
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1028 event client-anomaly [crackable-wep-iv-key-used|dos-broadcast-deauth| fuzzing-all-zero-macs|fuzzing-invalid-frame-type|fuzzing-invalid-mgmt- frames| fuzzing-invalid-seq-num|identical-src-and-dest-addr|invalid-8021x-frames| netstumbler-generic|non-changing-wep-iv|tkip-mic-counter- measures|wellenreiter] {filter-ageout [<0-86400>]} event enable-all-events event excessive [80211-replay-check-failure|aggressive-scanning| auth-server-failures|decryption-failures|dos-assoc-or-auth-flood| dos-eapol-start-storm |dos-unicast-deauth-or-disassoc|eap-flood|eap-nak- flood| frames-from-unassoc-station] {filter-ageout [<0-86400>]|threshold-client ap-ssid-broadcast-in-beacon Tracks AP SSID broadcasts in beacon events asleap Tracks ASLEAP attacks. These attacks break Lightweight Extensible Authentication Protocol (LEAP) passwords impersonation-attack Tracks impersonation attacks. These are also referred to as spoofing attacks, where the attacker assumes the address of an authorized device. null-probe-response Tracks null probe response attacks transmitting-device-using- invalid-mac Tracks transmitting device using invalid MAC attacks unencrypted-wired-leakage Tracks unencrypted wired leakage wireless-bridge Tracks wireless bridge (WDS) frames client-anomaly Enables client anomaly event tracking. These are suspicious client events compromising the security of the network crackable-wep-iv-key-used Tracks the use of a crackable WEP IV Key dos-broadcast-deauth Tracks DoS broadcast deauthentication events fuzzing-all-zero-macs Tracks Fuzzing: All zero MAC addresses observed fuzzing-invalid-frame-type Tracks Fuzzing: Invalid frame type detected fuzzing-invalid-mgmt-frames Tracks Fuzzing: Invalid management frame detected fuzzing-invalid-seq-num Tracks Fuzzing: Invalid sequence number detected identical-src-and-dest-addr Tracks identical source and destination addresses detection invalid-8021x-frames Tracks Fuzzing: Invalid 802.1x frames detected netstumbler-generic Tracks Netstumbler (v3.2.0, 3.2.3, 3.3.0) events non-changing-wep-iv Tracks unchanging WEP IV events tkip-mic-counter-measures Tracks TKIP MIC counter measures caused by station wellenreiter Tracks Wellenreiter events filter-ageout <0-86400> The following are common to all of the above client anomaly events: Optional. Configures the filter expiration interval in seconds <0-86400> Sets the filter ageout interval from 0 - 86400 seconds. The default is 0 seconds. enable-all-events Enables tracking of all intrusion events (client anomaly and excessive events)
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1029 [<0-5535>]| threshold-radio [<0-65535>]} Example wm3400-34710C8(config-wips-policy-test)#event excessive 80211-replay-check- failure filter-ageout 9 threshold-client 8 threshold-radio 99 wm3400-34710C8(config-wips-policy-test)#event client-anomaly wellenreiter filter-ageout 99 wm3400-34710C8(config-wips-policy-test)#show context wips-policy test event client-anomaly wellenreiter filter-ageout 99 event excessive 80211-replay-check-failure threshold-client 8 threshold- radio 99 filter-ageout 9 ap-detection-ageout 50 ap-detection-wait-time 15 wm3400-34710C8(config-wips-policy-test)# excessive Enables the tracking of excessive events. Excessive events are actions performed continuously and repetitively 80211-replay-check-failure Tracks 802.11replay check failure aggressive-scanning Tracks aggressive scanning events auth-server-failures Tracks failures reported by authentication servers decryption-failures Tracks decryption failures dos-assoc-or-auth-flood Tracks DoS association or authentication floods dos-eapol-start-storm Tracks DoS EAPOL start storms dos-unicast-deauth-or- disassoc Tracks DoS dissociation or deauthentication floods eap-flood Tracks EAP floods eap-nak-flood Tracks EAP NAK floods frames-from-unassoc-station Tracks frames from unassociated clients filter-ageout <0-86400> Optional. Configures a filter expiration interval in seconds. It sets the duration for which the client is filtered. The client is added to a ACL as a special entry and frames received from this client are dropped. <0-86400> Sets a filter ageout interval from 0 - 86400 seconds. The default is 0 seconds. threshold-client <0-65535> Optional. Configures a client threshold value after which the filter is triggered and an event is recorded <0-65535> Sets a wireless client threshold value from 0 - 65535 seconds threshold-radio <0-65535> Optional. Configures a radio threshold value after which the filter is triggered and an event is recorded <0-65535> Sets a radio threshold value from 0 - 65535 seconds
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1030 Related Commands history-throttle-duration wips-policy Configures the duration event duplicates are omitted from the event history Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax history-throttle-duration <30-86400> Parameters history-throttle-duration <30-86400> Example wm3400-34710C8(config-wips-policy-test)#history-throttle-duration 77 wm3400-34710C8(config-wips-policy-test)#show context wips-policy test history-throttle-duration 3000 event client-anomaly wellenreiter filter-ageout 99 event excessive 80211-replay-check-failure threshold-client 8 threshold- radio 99 filter-ageout 9 ap-detection-ageout 50 ap-detection-wait-time 15 no Disables WIPS policy events history-throttle-duration <30-86400> Configures the duration event duplicates are omitted from the event history <30-86400> Sets a value from 30 - 86400 seconds. The default is 120 seconds.
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1031 Related Commands no wips-policy Negates a command or resets configured settings to their default. When used in the config WIPS policy mode, the no command negates or resets filters and threshold values. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax no [ap-detection|enable|event|history-throttle-duration|signature|use] no [enable|history-throttle-duration] no ap-detection [ageout|wait-time] [<LINE-SINK>] no event [ap-anomaly|client-anomaly|enables-all-events|excessive] no event ap-anomaly [ad-hoc-violation|airjack|ap-ssid-broadcast-in-beacon| asleap| impersonation-attack|transmitting-device-using-invalid-mac|wireless- bridge] no event client-anomaly [crackable-wep-iv-key-used|dos-broadcast-deauth| fuzzing-all-zero-macs|fuzzing-invalid-frame-type|fuzzing-invalid- mgmt-frames| fuzzing-invalid-seq-num|identical-src-and-dest-addr|invalid-8021x- frames| netstumbler-generic|non-changing-wep-iv|tkip-mic-counter- measures|wellenreiter] {filter-ageout [<0-86400>]} no event excessive [80211-replay-check-failure|aggressive-scanning| auth-server-failures|decryption-failures|dos-assoc-or-auth-flood| dos-eapol-start-storm |dos-unicast-deauth-or-disassoc|eap-flood|eap- nak-flood| no Resets the history throttle duration to its default
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1032 frames-from-unassoc-station] {filter-ageout [<0-86400>]| threshold-client [<0-65535>]|threshold-radio [<0-65535>]} no signature <WIPS-SIGNATURE> no use device-categorization Parameters no [enable|history-throttle-duration] no ap-detection [ageout|wait-time] [<LINE-SINK>] no event ap-anomaly [ad-hoc-violation|airjack|ap-ssid-broadcast-in-beacon| asleap|impersonation-attack|transmitting-device-using-invalid-mac|wireless- bridge] no event client-anomaly [crackable-wep-iv-key-used|dos-broadcast-deauth| fuzzing-all-zero-macs|fuzzing-invalid-frame-type|fuzzing-invalid-mgmt- frames| fuzzing-invalid-seq-num|identical-src-and-dest-addr|invalid-8021x-frames| netstumbler-generic|non-changing-wep-iv|tkip-mic-counter- measures|wellenreiter] {filter-ageout [<0-86400>]} no enable Disables a WIPS policy from use with a wireless controller profile no history-throttle-duration Resets the history throttle duration to its default. This is the duration event duplicates are omitted from the event history. no ap-detection Disables the detection of unauthorized or unsanctioned APs ageout <LINE-SINK> Resets the ageout interval of a rogue device to its default (300 seconds) wait-time <LINE-SINK> Resets the wait time period to its default (60 seconds) no event Disables WIPS policy event tracking settings ap-anomaly Disables AP anomaly event tracking ad-hoc-violation Disables adhoc network violation event tracking airjack Disables the tracking of AirJack attacks ap-ssid-broadcast-in-beacon Disables the tracking of AP SSID broadcasts in beacon events asleap Disables the tracking of ASLEAP attacks impersonation-attack Disables the tracking of impersonation attacks transmitting-device-using- invalid-mac Disables the tracking of invalid device MAC addresses wireless-bridge Disables the tracking of wireless bridge frames no event Disables WIPS policy event tracking settings client-anomaly Disables client anomaly event tracking crackable-wep-iv-key-used Disables the tracking of the use of a crackable WEP IV Key dos-broadcast-deauth Disables DoS broadcast deauthentication event tracking
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1033 no event excessive [80211-replay-check-failure|aggressive-scanning| auth-server-failures|decryption-failures|dos-assoc-or-auth-flood| dos-eapol-start-storm |dos-unicast-deauth-or-disassoc|eap-flood|eap-nak- flood| frames-from-unassoc-station] {filter-ageout [<0-86400>]| threshold-client [<0-65535>]|threshold-radio [<0-65535>]} fuzzing-all-zero-macs Disables the tracking of Fuzzing: All zero MAC addresses observed fuzzing-invalid-frame-type Disables the tracking of Fuzzing: Invalid frame type detected fuzzing-invalid-mgmt-frames Disables the tracking of Fuzzing: Invalid management frame fuzzing-invalid-seq-num Disables the tracking of Fuzzing: Invalid sequence number identical-src-and-dest-addr Disables the tracking of identical source and destination addresses invalid-8021x-frames Disables the tracking of Fuzzing: Invalid 802.1x frames netstumbler-generic Disables Netstumbler (v3.2.0, 3.2.3, 3.3.0) event tracking non-changing-wep-iv Disables unchanging WEP IV event tracking tkip-mic-counter-measures Disables the tracking of TKIP MIC counter measures caused by a client wellenreiter Disables Wellenreiter event tracking filter-ageout <0-86400> The following are common to all of the above client anomaly events: Optional. Resets the filter expiration interval in seconds <0-86400> Resets a filter ageout interval from 0 - 86400 seconds no event Disables WIPS policy event tracking settings excessive Disables the tracking of excessive events. Excessive events consist of actions that are performed continuously and repetitively 80211-replay-check-failure Disables the tracking of 802.11 replay check failure aggressive-scanning Disables aggressive scanning event tracking auth-server-failures Disables the tracking of failures reported by authentication servers decryption-failures Disables the tracking of decryption failures dos-assoc-or-auth-flood Disables DoS association or authentication flood tracking dos-eapol-start-storm Disables the tracking of DoS EAPOL start storms dos-unicast-deauth-or- disassoc Disables DoS disassociation or deauthentication flood tracking eap-flood Disables the tracking of EAP floods eap-nak-flood Disables the tracking of EAP NAKfloods frames-from-unassoc-station Disables the tracking of frames from unassociated clients filter-ageout <0-86400> Optional. Resets the filter expiration interval in seconds. It resets the duration for which a client is filtered. The client is added to a ACL as a special entry and frames received from this client are dropped. <0-86400> Resets a filter ageout interval from 0 - 86400 seconds threshold-client <0-65535> Optional. Resets a client threshold limit after which the filter is triggered and an event is recorded in events history <0-65535> Resets a wireless client threshold limit from 0 - 65535 seconds threshold-radio <0-65535> Optional. Resets a radio threshold limit after which an event is recorded to events history <0-65535> Resets a radio threshold limit from 0 - 65535 seconds
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1034 no signature <WIPS-SIGNATURE> no use device-categorization Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-wips-policy-test)#show context wips-policy test history-throttle-duration 3000 event client-anomaly wellenreiter filter-ageout 99 event excessive 80211-replay-check-failure threshold-client 8 threshold- radio 99 filter-ageout 9 ap-detection-ageout 50 ap-detection-wait-time 15 wm3400-34710C8(config-wips-policy-test)#no history-throttle-duration wm3400-34710C8(config-wips-policy-test)#no event excessive 80211-replay- check-failure threshold-client 8 threshold-radio 99 filter-ageout 9 wm3400-34710C8(config-wips-policy-test)#show context wips-policy test event client-anomaly wellenreiter filter-ageout 99 no event excessive 80211-replay-check-failure threshold-client 8 threshold-radio 99 filter-ageout 9 ap-detection-ageout 50 ap-detection-wait-time 15 no signature Deletes a WIPS policy signature <WIPS-SIGNATURE> Defines the unique name given to a WIPS policy signature no use Disables the use of a device categorization policy with this WIPS policy device-categorization Resets the device categorization name to its default
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1035 Related Commands signature wips-policy Attack and intrusion patterns are identified and configured as signatures in a WIPS policy. The WIPS policy compares packets in the network with pre configured signatures to identify threats. When a threat is identified, the WIPS policy takes adequate actions. signature signature Configures a WIPS policy signature Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax signature <SIGNATURE-NAME> ap-detection Enables the detection of unauthorized or unsactioned access points enable Enables a WIPS policy for use with a wireless controller profile event Configures events, filters, and threshold values for a WIPS policy history-throttle-duration Configures the duration for which event duplicates are omitted from the event history signature Configures a WIPS policy signature use Enables the categorization of devices on this WIPS policy signature Configures a WIPS policy signature signature mode commands Summarizes the signature mode commands
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1036 Parameters signature <SIGNATURE-NAME> Example wm3400-34710C8(config-wips-policy-test)#signature test wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#show context signature test wm3400-34710C8(config-test-signature-test)# Related Commands signature mode commands signature The following table summarizes signature commands signature <SIGNATURE-NAME> Configures a WIPS policy signature <SIGNATURE-NAME> Enter a name for the WIPS policy signature. Provide a unique name for the signature, which will distinguish it from other signatures with similar configurations. The name should not exceed 64 characters. no Deletes a WIPS policy signature Commands Description Reference bssid Configures the BSSID MAC address page 22-1037 dst-mac Configures the destination MAC address page 22-1038 filter-ageout Configures the filter ageout interval page 22-1038 frame-type Configures the frame type used for matching page 22-1039 mode Enables or disables the signature mode page 22-1041 payload Configures payload settings page 22-1042 src-mac Configures the source MAC address page 22-1043 ssid-match Configures a match based on SSID page 22-1044 threshold-client Configures the wireless client threshold limit page 22-1045 threshold-radio Configures the radio threshold limit page 22-1046 no Negates a command or sets its default page 22-1047 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1037 bssid signature mode commands Configures a BSSID MAC address with this WIPS signature for matching Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax bssid <MAC> Parameters bssid <MAC> Example wm3400-34710C8(config-test-signature-test)#bssid 11-22-33-44-55-66 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 wm3400-34710C8(config-test-signature-test)# service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420 bssid <MAC> Configures a BSSID MAC address with this signature <MAC> Sets the MAC address Commands Description Reference
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1038 Related Commands dst-mac signature mode commands Configures a destination MAC address for the packet examined for matching Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax dst-mac <MAC> Parameters dst-mac <MAC> Example wm3400-34710C8(config-test-signature-test)#dst-mac 55-66-77-88-99-00 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 dst-mac 55-66-77-88-99-00 wm3400-34710C8(config-test-signature-test)# Related Commands filter-ageout signature mode commands no Resets a WIPS signature BSSID dst-mac <MAC> Configures a destination MAC address with this WIPS signature <MAC> Sets the MAC address no Resets a WIPS signature destination MAC address
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1039 Configures the filter ageout interval in seconds. This is the duration a client, triggering a WIPS event, is excluded from RF Domain manager radio association. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax filter-ageout <1-86400> Parameters filter-ageout <1-86400> Example wm3400-34710C8(config-test-signature-test)#filter-ageout 8 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 dst-mac 55-66-77-88-99-00 filter-ageout 8 wm3400-34710C8(config-test-signature-test)# Related Commands frame-type signature mode commands Configures the frame type used for matching with this signature filter-ageout <1-86400> Configures the filter ageout interval from 1 - 86400 seconds no Resets the filter ageout interval
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1040 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax frame-type [all|assoc|auth|beacon|data|deauth|disassoc|mgmt|probe- req|probe-resp| reassoc] Parameters frame-type [all|assoc|auth|beacon|data|deauth|disassoc|mgmt|probe- req|probe-resp| reassoc] Usage Guidelines The frame type configured determines the SSID match type configured. To configure the SSID match type as SSID, the frame type must be beacon, probe-req or probe-resp. Example wm3400-34710C8(config-test-signature-test)#frame-type reassoc wm3400-34710C8(config-test-signature-test)#show context signature test frame-type Configures the frame type used for matching all Configures all frame types assoc Configures association frames auth Configures authentication frames beacon Configures beacon frames data Configures data frames deauth Configures deauthentication frames disassoc Configures disassociation frames mgmt Configures management frames probe-req Configures probe request frames probe-resp Configures probe response frames reassoc Configures re-association frames
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1041 bssid 11-22-33-44-55-66 dst-mac 55-66-77-88-99-00 frame-type assoc filter-ageout 8 wm3400-34710C8(config-test-signature-test)# Related Commands mode signature mode commands Enables or disables a signature mode Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax mode enable Parameters mode enable Example wm3400-34710C8(config-test-signature-test)#enable wm3400-34710C8(config-wips-policy-test)# no Resets a WIPS signature frame type mode enable Enables signature mode
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1042 Related Commands payload signature mode commands Configures payload settings. The payload command sets a numerical index pattern and offset for this WIPS signature. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax payload <1-3> pattern <WORD> offset <0-255> Parameters payload <1-3> pattern <WORD> offset <0-255> Example wm3400-34710C8(config-test-signature-test)#payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 dst-mac 55-66-77-88-99-00 frame-type assoc filter-ageout 8 payload 1 pattern extreme offset 1 no Disables a WIPS signature mode payload <1-3> Configures payload settings <1-3> Sets the payload index pattern <WORD> Specifies the pattern to match: hex or string <WORD> Sets the pattern name offset <0-255> Specifies the payload offset to start the pattern match <0-255> Sets the offset value
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1043 wm3400-34710C8(config-test-signature-test)# Related Commands src-mac signature mode commands Configures a source MAC address for a packet examined for matching Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax src-mac <MAC> Parameters src-mac <MAC> Example wm3400-34710C8(config-test-signature-test)#src-mac 00-1E-E5-EA-1D-60 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 src-mac 00-1E-E5-EA-1D-60 dst-mac 55-66-77-88-99-00 frame-type assoc filter-ageout 8 payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# no Resets payload settings src-mac <MAC> Configures the source MAC address to match <MAC> Sets the source MAC address
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1044 Related Commands ssid-match signature Configures the SSID used for matching Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax ssid-match [ssid|ssid-len] ssid-match [ssid <SSID>|ssid-len <0-32>] Parameters ssid-match [ssid <SSID>|ssid-len <0-32>] Example wm3400-34710C8(config-test-signature-test)#ssid-match ssid PrinterLan wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 src-mac 00-1E-E5-EA-1D-60 dst-mac 55-66-77-88-99-00 frame-type beacon ssid-match ssid PrinterLan filter-ageout 8 payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# no Resets a WIPS signature source MAC address ssid <SSID> Specifies the SSID match string <SSID> Sets the SSID ssid-len <0-32> Specifies the character length of the SSID <0-32> Sets the SSID length from 0 - 32 characters
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1045 Related Commands threshold-client signature Configures the wireless client threshold limit. When the wireless client exceeds the specified limit, an event is triggered. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax threshold-client <0-65535> Parameters threshold-client <0-65535> Example wm3400-34710C8(config-test-signature-test)#threshold-client 88 wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 src-mac 00-1E-E5-EA-1D-60 dst-mac 55-66-77-88-99-00 frame-type beacon ssid-match ssid PrinterLan filter-ageout 8 threshold-client 88 payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# no Resets the SSID and the character length of the SSID threshold-client <1-65535> Configures the wireless client threshold limit <1-65535> Sets the threshold limit for a 60 second window from 1 - 65535
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1046 Related Commands threshold-radio signature Configures the radio threshold limit. When the radio exceeds the specified limit, an event is triggered. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax threshold-radio <1-65535>] Parameters threshold-radio <1-65535> Example wm3400-34710C8(config-test-signature-test)#threshold-radio 88 wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 src-mac 00-1E-E5-EA-1D-60 dst-mac 55-66-77-88-99-00 frame-type beacon ssid-match ssid PrinterLan filter-ageout 8 threshold-client 88 threshold-radio 88 no Resets the wireless client threshold limit threshold-radio <1-65535> Configures the radio threshold limit <1-65535> Specify the threshold limit for a 60 second window from 1 - 65535
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1047 payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# Related Commands no signature mode commands Negates a command or resets settings to their default. When used in the config WIPS policy signature mode, the no command resets or removes WIPS signature settings. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax no [bssid|dst-mac|filter-ageout|frame-type|mode|payload|src-mac|ssid-match| threshold-client|threshold-radio] no [bssid|dts-mac|filter-ageout|frame-type|mode enbale|payload <1-3>|src- mac| ssid-match [ssid|ssid-len]|threshold-client|threshold-radio] Parameters no [bssid|dst-mac|filter-ageout|frame-type|mode enbale|payload <1-3>|src- mac| ssid-match [ssid|ssid-len]|threshold-client|threshold-radio] no Resets the radio threshold limit no bssid Resets a WIPS signature BSSID no dst-mac Resets a WIPS signature destination MAC address no filter-ageout Resets the filter ageout interval. This is the duration a client, triggering a WIPS event, is excluded from RF Domain manager radio association. no frame-type Resets a WIPS signature frame type no mode enable Disables a WIPS signature enable Changes the mode from enabled to disabled
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1048 Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example The following is the WIPS signature before the execution of the no command: wm3400-34710C8(config-test-signature-test)#show context signature test bssid 11-22-33-44-55-66 src-mac 00-1E-E5-EA-1D-60 dst-mac 55-66-77-88-99-00 frame-type beacon ssid-match ssid PrinterLan filter-ageout 8 threshold-client 88 threshold-radio 88 payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# The following is the WIPS signature after the execution of the no command: wm3400-34710C8(config-test-signature-test)#no mode enable wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no bssid wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no dst-mac wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no src-mac wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no filter-ageout wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no threshold-client wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#no threshold-radio wm3400-34710C8(config-test-signature-test)# wm3400-34710C8(config-test-signature-test)#show context signature test no mode enable no payload <1-3> Resets payload settings. The payload command sets a numerical index pattern and offset for this WIPS signature <1-3> Sets the payload index no src-mac Resets a WIPS signature source MAC address no ssid-match [ssid|ssid-len] Resets the SSID character length ssid Removes the specified SSID match string ssid-len Removes the specified character length of the SSID no threshold-client Resets a wireless client threshold limit. When the wireless client exceeds the specified limit, an event is triggered. no threshold-radio Resets a radio threshold limit. When the radio exceeds the specified threshold limit, an event is triggered.
wips-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1049 frame-type beacon payload 1 pattern extreme offset 1 wm3400-34710C8(config-test-signature-test)# Related Commands use wips-policy Enables device categorization on this WIPS policy. This command uses an existing device categorization list, or creates a new device categorization list. The list categorizes devices as authorized or unauthorized. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3600 Syntax use device-categorization <DEVICE-CATEGORIZATION> bssid Configures a WIPS signature BSSID MAC address dst-mac Configures a destination MAC address for the packet examined for matching filter-ageout Configures the filter ageout interval frame-type Configures the frame type to match with a signature mode Enables or disables a WIPS signature payload Configures payload settings. The payload command sets a numerical index pattern and offset for this WIPS signature. src-mac Configures a source MAC address for the packet examined for matching ssid-match Configures a SSID for matching threshold-client Configures a wireless client threshold limit threshold-radio Configures a radio threshold limit
Chapter 22: WIPS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1050 Parameters use device-categorization <DEVICE-CATEGORIZATION> Example wm3400-34710C8(config-wips-policy-test)#use device-categorization test wm3400-34710C8(config-wips-policy-test)# wm3400-34710C8(config-wips-policy-test)#show context wips-policy test no enable signature test use device-categorization test wm3400-34710C8(config-wips-policy-test)# Related Commands device-categorization <DEVICE- CATEGORIZATION> Configures a device categorization list <DEVICE-CATEGORIZATION> Specify the device categorization object name to associate with this profile no Disables the use of a device categorization policy with a WIPS policy
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1051 C H A P T E R 23 WLAN QoS Policy This chapter summarizes the WLAN QoS policy in detail. A WLAN QoS policy increases network efficiency by prioritizing data traffic. Prioritization reduces congestion. This is essential because of the lack of bandwidth for all users and applications. QoS ensures WLANs get a share of the bandwidth equally or per the configured proportion. Each WLAN QoS policy has a set of parameters which it groups into categories, such as management, voice and data. Packets within each category are processed based on the weights defined for each WLAN. Use the (config) instance to configure WLAN QoS policy commands. To navigate to the WLAN QoS policy instance, use the following commands: wm3400-34710C8(config)#wlan-qos-policy <POLICY-NAME> wm3400-34710C8(config)#wlan-qos-policy test wm3400-34710C8(config-wlan-qos-test)#? WLAN QoS Mode commands: accelerated-multicast Configure accelerated multicast streams address and forwarding QoS classification classification Select how traffic on this WLAN must be classified (relative prioritization on the radio) multicast-mask Egress multicast mask (frames that match bypass the PSPqueue. This permits intercom mode operation without delay even in the presence of PSP clients) no Negate a command or set its defaults qos Quality of service rate-limit Configure traffic rate-limiting parameters on a per-wlan/per-client basis svp-prioritization Enable spectralink voice protocol support on this wlan voice-prioritization Prioritize voice client over other client (for non-WMM clients) wmm Configure 802.11e/Wireless MultiMedia parameters clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1052 end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-wlan-qos-test)# wlan-qos-policy WLAN QoS Policy The following table summarizes WLAN QoS policy commands accelerated-multicast wlan-qos-policy Configures the accelerated multicast stream address and forwarding QoS classification Command Description Reference accelerated- multicast Configures accelerated multicast stream addresses and forwards QoS classifications page 23-1052 classification Classifies WLAN traffic based on priority page 23-1054 multicast-mask Configures the egress prioritization multicast mask page 23-1055 no Negates a command or sets its default page 23-1056 qos Defines the QoS configuration page 23-1059 rate-limit Configures the WLAN traffic rate limit using a WLAN QoS policy page 23-1060 svp-prioritization Enables Spectralink voice protocol support on a WLAN page 23-1062 voice-prioritization Prioritizes voice client over other clients page 23-1063 wmm Configures 802.11e/wireless multimedia parameters page 23-1063 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1053 AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accelerated-multicast [<IP>|autodetect] accelerated-multicast [<IP>|autodetect] {classification [background| best-effort|trust|video|voice]} Parameters accelerated-multicast [<IP>|autodetect] {classification [background| best-effort|trust|video|voice]} Example wm3400-34710C8(config-wlan-qos-test)#accelerated-multicast autodetect classification voice wm3400-34710C8(config-wlan-qos-test)# wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test accelerated-multicast Configures the accelerated multicast stream address and forwarding QoS classification <IP> Configures a multicast IP address in the A.B.C.D format. The system can configure up to 32 IP addresses for each WLAN QoS policy autodetect Allows the system to automatically detect multicast streams. This parameter allows the system to convert multicast streams to unicast, or to specify multicast streams converted to unicast. classification Optional. Configures the forwarding QoS classification (traffic class). When the stream is converted and queued for transmission, specify the type of classification applied to the stream. background Forwards streams with background (low) priority. This parameter is common to both <IP> and autodetect. best-effort Forwards streams with best effort (normal) priority. This parameter is common to both <IP> and autodetect. trust No change to the streams forwarding traffic class. This parameter is common to both <IP> and autodetect. video Forwards streams with video traffic priority. This parameter is common to both <IP> and autodetect. voice Forwards streams with voice traffic priority. This parameter is common to both <IP> and autodetect.
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1054 qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice wm3400-34710C8(config-wlan-qos-test)# classification wlan-qos-policy Specifies how traffic on this WLAN is classified. This classification is based on relative prioritization on the radio. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax classification [low|non-unicast|non-wmm|normal|video|voice|wmm] classification [low|normal|video|voice|wmm] classification non-unicast [voice|video|normal|low|default] classification non-wmm [voice|video|normal|low] Parameters classification [low|normal|video|voice|wmm] classification non-unicast [voice|video|normal|low|default] low Specifies all WLAN traffic is treated as low priority (background) normal Specifies all WLAN traffic is treated as normal priority (best effort) video Specifies all WLAN traffic is treated as video voice Specifies all WLAN traffic is treated as voice wmm Uses WMM based classification, using DSCP or 802.1p tags, to classify traffic into different queues non-unicast Specifies how broadcast and multicast traffic is classified video Specifies all WLAN non-unicast traffic is classified and treated as video packets
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1055 classification non-wmm [voice|video|normal|low] Example wm3400-34710C8(config-wlan-qos-test)#classification wmm wm3400-34710C8(config-wlan-qos-test)#classification non-wmm video wm3400-34710C8(config-wlan-qos-test)# wm3400-34710C8(config-wlan-qos-test)#classification non-unicast normal wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video classification non-unicast normal qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice wm3400-34710C8(config-wlan-qos-test)# multicast-mask wlan-qos-policy Configure an egress prioritization multicast mask for this WLAN QoS policy. By configuring a primary or secondary prioritization multicast mask, the network administrator can indicate which packets are to be transmitted immediately. voice Specifies all WLAN non-unicast traffic is classified and treated as voice packets normal Specifies all WLAN non-unicast traffic is classified and treated as normal priority packets (best effort) low Specifies all WLAN non-unicast traffic is classified and treated as low priority packets (background) default Uses the classification mode (same as unicast classification if WMM is disabled, normal if unicast classification is WMM) non-wmm Specifies how traffic from non-WMM clients is classified voice Specifies all WLAN non-WMM client traffic is classified and treated as voice packets video Specifies all WLAN non-WMM client traffic is classified and treated as video packets normal Specifies all WLAN non-WMM client traffic is classified and treated as normal priority packets (best effort) low Specifies all WLAN non-WMM client traffic is classified and treated as low priority packets (background)
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1056 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax multicast-mask [primary|secondary] <MAC/MASK> Parameters multicast-mask [primary|secondary] <MAC/MASK> Example wm3400-34710C8(config-wlan-qos-test)#multicast-mask primary 11-22-33-44-55- 66/22-33-44-55-66-77 wm3400-34710C8(config-wlan-qos-test)#show context wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video multicast-mask primary 11-22-33-44-55-66/22-33-44-55-66-77 classification non-unicast normal qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice no wlan-qos-policy Negates a command or resets settings to their default primary <MAC/MASK> Configures the primary egress prioritization multicast mask <MAC/MASK> Sets the MAC address and the mask in the ABB-CC-DD-EE- FF/XX-XX-XX-XX-XX-XX-XX format secondary <MAC/MASK> Configures the primary egress prioritization multicast mask <MAC/MASK> Sets the MAC address and the mask in the ABB-CC-DD-EE- FF/XX-XX-XX-XX-XX-XX-XX format
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1057 Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [accelerated-multicast|classification|multicast-mask|qos|rate-limit| svp-prioritization|voice-prioritization|wmm] no [accelerated-multicast [<IP>|autodetect]|classification [non-unicast| non-wmm]|multicast-mask [primary|secondary]|qos trust [dscp|wmm]| svp-prioritization|voice-prioritization] no rate-limit [client|wlan] [from-air|to-air] [max-burst-size|rate| red-threshold] no rate-limit [client|wlan] [from-air|to-air] [max-burst-size|rate| red-threshold [background|best-effort|video|voice]] no wmm [background|best-effort|power-save|qbss-load-element|video|voice] no wmm [power-save|qbss-load-element] no wmm [backgorund|best-effort|video|voice] [aifsn|cw-max|cw-min|txop- limit] Parameters no [accelerated-multicast [<IP>|autodetect]| classification [non-unicast|non-wmm]|multicast-mask [primary|secondary]| qos trust [dscp|wmm]|svp-prioritization|voice-prioritization] no accelerated-multicast [<IP>|autodetect>] Disables accelerated multicast streams and forwarding QoS classification <IP> Specifies the IP address to remove <autodetect> Removes automatic detection of multicast streams no classification [non-unicast| non-wmm] Disables the WLAN classification scheme non-unicast Removes classification for multicast and broadcast packets non-wmm Removes classification for non-WMM client traffic no multicast-mask [procrastinatory] Disables the egress prioritization primary or secondary multicast mask primary Removes the first egress multicast mask secondary Removes the second egress multicast mask
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1058 no rate-limit [client|wlan] [from-air|to-air] [max-burst-size|rate| red-threshold [background|best-effort|video|voice] no wmm [power-save|qbss-load-element] no wmm [backgorund|best-effort|video|voice] [aifsn|cw-max|cw-min|txop- limit] Example wm3400-34710C8(config-wlan-qos-test)#no classification wm3400-34710C8(config-wlan-qos-test)#no multicast-mask primary no qos trust [disquiet] Disables the QoS service trust Ignores the trust QOS values of ingressing packets dscp Ignores the IP DSCP values of ingressing packets wmm Ignores the 802.11 WMM QoS values of ingressing packets no svp-prioritization Disables support for the Spectralink Voice Protocol (SVP) on a WLAN no voice-prioritization Disables the priority of voice clients over other clients (applies to non-WMM clients) no rate-limit [client|wlan] Disables traffic rate limit parameters Disables client traffic rate limits Disables WLAN traffic rate limits [from-air|to-air] The following are common to the client and WLAN parameters: from-air Removes client/WLAN traffic rate limits in the up link direction. This is traffic from the wireless client to the network to-air Removes client/WLAN traffic rate limits in the down link direction. This is traffic from the network to the wireless client max-burst-size Disables the maximum burst size value rate Disables the traffic rates configured for a wireless client or WLAN red-threshold Disables random early detection threshold values configured for the traffic class background Disables the low priority traffic (background) threshold value best-effort Disables the normal priority traffic (best effort) threshold value video Disables the video traffic threshold value voice Disables the voice traffic threshold value no wmm Disables 802.11e/wireless multimedia parameters power-save Disables support for WMM-Powersave (U-APSD) qbss-load-element Disables support for the QBSS load information element in beacons and probe responses no wmm Disables 802.11e/wireless multimedia parameters background Disables background access category parameters best-effort Disables best effort access category parameters video Disables video access category parameters voice Disables voice access category parameters
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1059 wm3400-34710C8(config-wlan-qos-test)#no qos trust dscp wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-unicast voice no qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice wm3400-34710C8(config-wlan-qos-test)# Related Commands qos wlan-qos-policy Enables QoS on this WLAN Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax qos trust [dscp|wmm] accelerated-multicast Configures the accelerated multicast streams address and forwards the QoS classification classification Classifies WLAN traffic based on priority multicast-mask Configures the egress prioritization multicast mask qos Defines the QoS configuration rate-limit Configures a WLANs traffic rate limits svp-prioritization Enables Spectralink voice protocol support on a WLAN voice-prioritization Prioritizes voice client over other clients wmm Configures the 802.11e/wireless multimedia parameters
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1060 Parameters qos trust [dscp|wmm] Example wm3400-34710C8(config-wlan-qos-test)#qos trust wmm wm3400-34710C8(config-wlan-qos-test)#qos trust dscp wm3400-34710C8(config-wlan-qos-test)# rate-limit wlan-qos-policy Configures the WLAN traffic rate limits using the WLAN QoS policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax rate-limit [client|wlan] [from-air|to-air] {max-burst-size|rate| red-threshold} rate-limit [client|wlan] [from-air|to-air] {max-burst-size <2-1024>| rate <50-1000000>} rate-limit [client|wlan] [from-air|to-air] {red-threshold [background <0-100>|best-effort <0-100>|video <0-100>|voice <0- 100>]} Parameters rate-limit [client|wlan] [from-air|to-air] {max-burst-size <2-1024>| rate <50-1000000>} trust [dscp|wmm] Trusts the QoS values of ingressing packets dscp Trusts the IP DSCP values of ingressing packets wmm Trusts the 802.11 WMM QoS values of ingressing packets rate-limit Configures traffic rate limit parameters
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1061 rate-limit [client|wlan] [from-air|to-air] {red-threshold [background <0- 100>|best-effort <0-100>|video <0-100>|voice <0-100>]} Example wm3400-34710C8(config-wlan-qos-test)#rate-limit wlan from-air max-burst- size 6 wm3400-34710C8(config-wlan-qos-test)#rate-limit wlan from-air rate 55 wm3400-34710C8(config-wlan-qos-test)#rate-limit wlan from-air red-threshold best-effort 10 wm3400-34710C8(config-wlan-qos-test)#no rate-limit wlan from-air red- threshold best-effort wm3400-34710C8(config-wlan-qos-test)#rate-limit client from-air red- threshold background 3 wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video multicast-mask primary 11-22-33-44-55-66/22-33-44-55-66-77 classification non-unicast normal rate-limit wlan from-air rate 55 rate-limit wlan from-air max-burst-size 6 rate-limit wlan from-air red-threshold best-effort 10 rate-limit client from-air red-threshold background 3 qos trust dscp client Configures traffic rate limiting parameters on a per-client basis wlan Configures traffic rate limiting parameters on a per-WLAN basis from-air Configures traffic rate limiting from a wireless client to the network to-air Configures the traffic rate limit from the network to a wireless client max-burst-size <2-1024> Optional. Sets the maximum burst size from 2 - 1024 kbytes. The chances of the upstream or downstream packet transmission getting congested for the WLANs client destination are reduced for smaller burst sizes. The default is 320 kbytes. rate <50-1000000> Optional. Sets the traffic rate from 50 - 1000000 kbps. This limit is the threshold value for the maximum number of packets received or transmitted over the WLAN from all access categories. Any traffic that exceeds the specified rate is dropped by the wireless controller and a log message is generated. The default is 5000 kbps. rate-limit Configures traffic rate limit parameters client Configures traffic rate limiting parameters on a per-client basis wlan Configures traffic rate limiting parameters on a per-WLAN basis from-air Configures traffic rate limiting from a wireless client to the network to-air Configures the traffic rate limit from the network to a wireless client red-threshold Configures random early detection threshold values for a designated traffic class background <0-100> Sets a threshold value for low priority traffic from 0 - 100 best-effort <0-100> Sets a threshold value for normal priority traffic from 0 - 100 video <0-100> Sets a threshold for video traffic from 0 - 100 voice <0-100> Sets a threshold for voice traffic from 0 - 100
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1062 qos trust wmm accelerated-multicast autodetect classification voice svp-prioritization wlan-qos-policy Enables WLAN SVP support on this WLAN QoS policy. Enabling SVP enables the wireless controller to identify and prioritize traffic from Spectralink/Ploycomm phones. This feature is enabled by default. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax svp-prioritization Parameters None Example wm3400-34710C8(config-wlan-qos-test)#svp-prioritization wm3400-34710C8(config-wlan-qos-test)# wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video svp-prioritization multicast-mask primary 11-22-33-44-55-66/22-33-44-55-66-77 classification non-unicast normal rate-limit wlan from-air rate 55 rate-limit wlan from-air max-burst-size 6 rate-limit wlan from-air red-threshold best-effort 10 rate-limit client from-air red-threshold background 3 qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1063 voice-prioritization wlan-qos-policy Prioritizes voice clients over other clients (for non-WMM clients). This feature is enabled by default. Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax voice-prioritization Parameters None Example wm3400-34710C8(config-wlan-qos-test)#voice-prioritization wm3400-34710C8(config-wlan-qos-test)# wm3400-34710C8(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video svp-prioritization voice-prioritization multicast-mask primary 11-22-33-44-55-66/22-33-44-55-66-77 classification non-unicast normal rate-limit wlan from-air rate 55 rate-limit wlan from-air max-burst-size 6 rate-limit wlan from-air red-threshold best-effort 10 rate-limit client from-air red-threshold background 3 qos trust dscp qos trust wmm accelerated-multicast autodetect classification voice wmm wlan-qos-policy
Chapter 23: WLAN QoS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1064 Configures 802.11e/wireless multimedia parameters for this WLAN QoS policy Supported on the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax wmm [background|best-effort|power-save|qbss-load-element|video|voice] wmm [power-save|qbss-load-element] wmm [background|best-effort|video|voice] [aifsn <2-15>|cw-max <0-15>| cw-min <0-15>|txop-limit <0-65535>] Parameters wmm [power-save|qbss-load-element] wmm [background|best-effort|video|voice] [aifsn <2-15>|cw-max <0-15>| cw-min <0-15>|txop-limit <0-65535>] wmm Configures 802.11e/wireless multimedia parameters power-save Enables support for the WMM-Powersave mechanism. This mechanism, also known as Unscheduled Automatic Power Save Delivery (U-APSD), is specifically designed for WMM voice devices. qbss-load-element Enables support for the QOS Basic Service Set (QBSS) load information element in beacons and probe response packets advertised by access packets. This feature is enabled by default. wmm Configures 802.11e/wireless multimedia parameters. This parameter enables the configuration of four access categories. Applications assign each data packet to one of these four access categories and queues them for transmission. background Configures background access category parameters best-effort Configures best effort access category parameters. Packets not assigned to any particular access category are categorized by default as having best effort priority video Configures video access category parameters voice Configures voice access category parameters
wlan-qos-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1065 Example wm3400-34710C8(config-wlan-qos-test)#wmm background aifsn 7 wm3400-34710C8(config-wlan-qos-test)#wmm video txop-limit 9 wm3400-34710C8(config-wlan-qos-test)#wmm voice cw-min 6 wm3400-34710C8(config-wlan-qos-test)#wmm qbss-load-element wm3700-37FABE(config-wlan-qos-test)#show context wlan-qos-policy test classification non-wmm video svp-prioritization aifsn <2-15> Configures Arbitrary Inter-Frame Space Number (AIFSN) from 2 - 15. AIFSN is the wait time between data frames. This parameter is common to background, best effort, video and voice. The default for traffic voice categories is 2 The default for traffic video categories is 2 The default for traffic best effort (normal) categories is 3 The default for traffic background (low) categories is 7 <2-15> Sets a value from 2 - 15 cw-max <0-15> Configures the maximum contention window. Wireless clients pick a number between 0 and the minimum contention window to wait before retransmission. Wireless clients then double their wait time on a collision, until it reaches the maximum contention window. This parameter is common to background, best effort, video and voice. The default for traffic voice categories is 3 The default for traffic video categories is 4 The default for traffic best effort (normal) categories 10 The default for traffic background (low) categories is 10 <0-15> ECW: the contention window. The actual value used is (2^ECW - 1). Set a value from 0 - 15. cw-min <0-15> Configures the minimum contention window. Wireless clients pick a number between 0 and the min contention window to wait before retransmission. Wireless clients then double their wait time on a collision, until it reaches the maximum contention window. This parameter is common to background, best effort, video and voice. The default for traffic voice categories is 2 The default for traffic video categories is 3 The default for traffic best effort (normal) categories is 4 The default for traffic background (low) categories is 4 <0-15> ECW: the contention window. The actual value used is (2^ECW - 1). Set a value from 0 - 15. txop-limit <0-65535> Configures the transmit-opportunity (the interval of time during which a particular client has the right to initiate transmissions). This parameter is common to background, best effort, video and voice. The default for traffic voice categories is 47 The default for traffic video categories is 94 The default for traffic best effort (normal) categories is 0 The default for traffic background (low) categories is 0 <0-65535> Set a value from 0 - 65535 to configure the transmit-opportunity in 32 microsecond units.
TM 4000 Series Access Point CLI Reference Guide 1067 C H A P T E R 24 Interface Radio Commands Use the (config-profile-default-WM3400) instance to configure radio instances associated with the wireless controller. To switch to this mode, use: WM3400- 37FAB(config-profile-default-WM3400)#interface radio ? 1 Radio interface 1 2 Radio interface 2 3 Radio interface 3 WM3400-37FABE(config-profile-default-WM3400)#interface radio WM3400-880DA7(config-profile-default-WM3400-if-radio1)#? Radio Mode commands: ack-timeout Configure the 802.11 ACK timeout aggregation Configure 802.11n aggregation related parameters airtime-fairness Enable fair access to medium for clients based on their usage of airtime antenna-gain Specifies the antenna gain of this radio antenna-mode Configure the antenna mode (number of transmit and receive antennas) on the radio beacon Configure beacon parameters channel Configure the channel of operation for this radio data-rates Specify the 802.11 rates to be supported on this radio description Configure a description for this radio dynamic-chain-selection Automatic antenna-mode selection (single antenna for non-11n transmit rates) guard-interval Configure the 802.11n guard interval lock-rf-mode Retain user configured rf-mode setting for this radio max-clients Maximum number of wireless clients allowed to associate mesh Configure radio mesh parameters no Negate a command or set its defaults non-unicast Configure handling of non-unicast frames off-channel-scan Enable off-channel scanning on the radio placement Configure the location where this radio is
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1068 operating power Configure the transmit power of the radio preamble-short User short preambles on this radio probe-response Configure transmission parameters for Probe Response frames radio-tap-mode Configure the radio-tap mode of operation for this radio rf-mode Configure the rf-mode of operation for this radio rifs Configure Reduced Interframe Spacing (RIFS) parameters rts-threshold Configure the RTS threshold shutdown Shutdown the selected radio interface sniffer-redirect Capture packets and redirect to an IP address running a packet capture/analysis tool use Set setting to use wireless-client Configure wireless client related parameters wlan Enable wlans on this radio clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal WM3400-880DA7(config-profile-default-WM3400-if-radio1)# interface-radio Instance The following table summarizes interface radio commands Commands Description Reference ack-timeout Configures the 802.11 ACK timeout period page 24-1069 aggregation Configures 802.11n aggregation parameters page 24-1070 airtime-fairness Enables fair access for clients based on airtime usage page 24-1073 antenna-gain Specifies the antenna gain of the selected radio page 24-1073 antenna-mode Configures the radio antenna mode page 24-1074 beacon Configures beacon parameters page 24-1075 channel Configures a radios channel of operation page 24-1077 data-rates Specifies the 802.11 rates supported on a radio page 24-1078 description Defines a radios description page 24-1080
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1069 ack-timeout interface-radio Instance Configures the 802.11 ACK timeout period. When a packet is sent out from one wireless client to another, it waits for an acknowledgement (ACK) frame from the receiving client. If an ACK is not received within the specified timeout period, the packet is re-transmitted resulting in reduced throughput. dynamic-chain- selection Enables automatic antenna mode selection page 24-1081 guard-interval Configures the 802.11n guard interval page 24-1082 lock-rf-mode Retains user configured radio RF mode settings page 24-1083 max-clients Defines the maximum number of wireless clients allowed to associate page 24-1083 mesh Configures radio mesh parameters page 24-1084 no Negates a command or sets its default page 24-1086 non-unicast Configures the handling of non unicast frames page 24-1089 off-channel-scan Enables radio off channel scanning page 24-1091 placement Configures the location where a radio is deployed page 24-1093 power Configures the radio transmit power page 24-1093 preamble-short Configures user short preambles on the radio page 24-1094 probe-response Configures transmission parameters for probe response frames page 24-1095 radio-tap-mode Configures the radio tap mode for a radio page 24-1096 rf-mode Configures a radio RF mode page 24-1097 rifs Configures Reduced Interframe Spacing (RIFS) parameters page 24-1098 rts-threshold Configures a radios RTS threshold value page 24-1099 shutdown Terminates a selected radio interface page 24-1100 sniffer-redirect Captures and redirects packets to an IP address running a packet capture/analysis tool page 24-1100 use Applies other configuration profiles or values on the current configuration item page 24-1101 wireless-client Configures wireless client related parameters page 24-1102 wlan Enables a radio WLAN page 24-1103 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-382 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-388 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-418 show Displays running system information page 7-425 write Writes the system running configuration to memory or terminal page 6-420 Commands Description Reference
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1070 Supported on the following platforms: WM3411 Syntax ack-timeout <1-100> Parameters ack-timeout <1-100> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands aggregation interface-radio Instance Configures 802.11n frame aggregation. Frame aggregation increases throughput by sending two or more data frames in a single transmission. There are two types of frame aggregation: MAC Service Data Unit (MSDU) aggregation and MAC Protocol Data Unit (MPDU) aggregation. Both modes group several data frames into one large data frame. Supported on the following platforms: WM3411 Syntax aggregation [ampdu|amsdu] aggregation ampdu [rx-only|tx-only|tx-rx|none|max-aggr-size|min-spacing] aggregation ampdu [rx-only|tx-only|tx-rx|none] ack-timeout <1-100> Configures the 802.11 ACK timeout period in microseconds <1-100> Specify the ACK timeout period from 1 - 100 microseconds. If the ACK timeout period set is too high, throughput is degraded waiting for the ACK window to timeout on lost packets. no Resets the 802.11 ACK timeout period to default
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1071 aggregation ampdu max-aggr-size [rx|tx] aggregation ampdu max-aggr-size rx [8191|16383|32767|65535] aggregation ampdu max-aggr-size tx [<0-65535>] aggregation ampdu min-spacing [0|1|2|4|8|16] aggregation amsdu [rx-only|tx-rx] Parameters aggregation ampdu [rx-only|tx-only|tx-rx|none] aggregation ampdu max-aggr-size rx [8191|16383|32767|65535] aggregation ampdu max-aggr-size tx [<0-65535>] aggregation Configures 802.11n frame aggregation parameters ampdu Configures Aggregate MAC Protocol Data Unit (AMPDU) frame aggregation parameters. AMPDU aggregation collects Ethernet frames addressed to a single destination. It wraps each frame in an 802.11n MAC header. This aggregation mode is less efficient, but more reliable in environments with high error rates. It enables the acknowledgement and retransmission of each aggregated data frame individually. tx-only Supports the transmission of AMPDU aggregated frames only rx-only Supports the receipt of AMPDU aggregated frames only tx-rx Supports the transmission and receipt of AMPDU aggregated frames none Disables support for AMPDU aggregation aggregation Configures 802.11n frame aggregation parameters ampdu Configures AMPDU frame aggregation parameters. AMPDU aggregation collects Ethernet frames addressed to a single destination. It wraps each frame in an 802.11n MAC header. This aggregation mode is less efficient, but more reliable in environments with high error rates. It enables the acknowledgement and retransmission of each aggregated data frame individually. max-aggr-size Configures AMPDU packet size limits. Configure the packet size limit on packets both transmitted and received. rx [8191|16383|32767|65535] Configures the limit on received frames 8191 Advertises a maximum of 8191 bytes 16383 Advertises a maximum of 16383 bytes 32767 Advertises a maximum of 32767 bytes 65536 Advertises a maximum of 65535 bytes aggregation Configures 802.11n frame aggregation parameters ampdu Configures AMPDU frame aggregation parameters. AMPDU aggregation collects Ethernet frames addressed to a single destination. It wraps each frame in an 802.11n MAC header. This aggregation mode is less efficient, but more reliable in environments with high error rates. It enables the acknowledgement and retransmission of each aggregated data frame individually.
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1072 aggregation ampdu min-spacing [0|1|2|4|8|16] aggregation amsdu [rx-only|tx-rx] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#aggregation ampdu tx-only WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary aggregation ampdu tx-only ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# max-aggr-size Configures AMPDU packet size limits. Configure the packet size limit on packets both transmitted and received. tx <0-65535> Configures the limit on transmitted frames <0-65535> Sets the limit from 0 - 65536 bytes aggregation Configures 802.11n frame aggregation parameters ampdu Configures AMPDU frame aggregation parameters. AMPDU aggregation collects Ethernet frames addressed to a single destination. It wraps each frame in an 802.11n MAC header. This aggregation mode is less efficient, but more reliable in environments with high error rates. It enables the acknowledgement and retransmission of each aggregated data frame individually. mn-spacing [0|1|2|4|8|16] Configures the minimum gap, in microseconds, between AMPDU frames 0 Configures the minimum gap as 0 microseconds 1 Configures the minimum gap as 1 microseconds 2 Configures the minimum gap as 2 microseconds 4 Configures the minimum gap as 4 microseconds 8 Configures the minimum gap as 8 microseconds 16 Configures the minimum gap as 16 microseconds aggregation Configures 802.11n frame aggregation parameters amsdu Configures Aggregated MAC Service Data Unit (AMSDU) frame aggregation parameters. AMSDU aggregation collects Ethernet frames addressed to a single destination. But, unlike AMPDU, it wraps all frames in a single 802.11n frame. rx-only Supports the receipt of AMSDU aggregated frames only tx-rx Supports the transmission and receipt of AMSDU aggregated frames
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1073 Related Commands airtime-fairness interface-radio Instance Enables equal access for wireless clients based on their airtime usage Supported on the following platforms: WM3411 Syntax airtime-fairness {prefer-ht} {weight [<1-10>]} Parameters airtime-fairness {prefer-ht} {weight [<1-10>]} Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#airtime-fairness prefer-ht weight 6 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#Show context interface radio1 wlan wlan1 bss 1 primary aggregation ampdu tx-only airtime-fairness prefer-ht weight 6 ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands antenna-gain interface-radio Instance no Disables 802.11n aggregation parameters airtime-fairness Enables equal access for wireless clients based on their airtime usage prefer-ht Optional. Gives preference to high throughput (802.11n) clients over legacy clients weight <1-10> Configures the relative weightage for 11n clients over legacy clients. <1-10> Sets a weightage ratio for 11n clients from 1 - 10 no Disables fair access to medium for wireless clients (provides access on a round- robin mode)
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1074 Configures the antenna gain value of the selected radio. Antenna gain defines the ability of an antenna to convert power into radio waves and vice versa. Supported on the following platforms: WM3411 Syntax antenna-gain <0.0-15.0> Parameters antenna-gain <0.0-15.0> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#antenna-gain 12.0 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary antenna-gain 12.0 aggregation ampdu tx-only airtime-fairness prefer-ht weight 6 ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands antenna-mode interface-radio Instance Configures the antenna mode (the number of transmit and receive antennas) on the radio Supported on the following platforms: WM3411 Syntax antenna-mode [1*1|1*3|2*2|default] <0.0-15.0> Sets the antenna gain from 0.0 - 15.0 dBi no Resets the antenna gain of a radio
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1075 Parameters antenna-mode [1*1|1*3|2*2|default] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#antenna-mode 2x2 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary antenna-gain 12.0 aggregation ampdu tx-only antenna-mode 2x2 airtime-fairness prefer-ht weight 6 ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands beacon interface-radio Instance Configures radio beacon parameters. Beacons are packets sent by the access point to synchronize a wireless network. Supported on the following platforms: WM3411 Syntax beacon [dtim-period|period] beacon dtim-period [<1-50>|bss] beacon dtim-period [<1-50>|bss <1-8> <1-50>] beacon period [50|100|200] 1*1 Uses antenna A to receive and transmit 1*3 Uses antenna A to transmit and receives on other antennas 2*2 Uses antenna A and C for both transmit and receive default Uses default antenna settings no Resets the radio antenna mode (the number of transmit and receive antennas) to its default
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1076 Parametersd beacon dtim-period [<1-50>|bss <1-8> <1-50>] beacon period [50|100|200] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#beacon dtim-period bss 2 20 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#beacon period 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 beacon period 50 beacon dtim-period bss 1 2 beacon dtim-period bss 2 20 beacon dtim-period bss 3 2 beacon dtim-period bss 4 2 beacon dtim-period bss 5 2 beacon dtim-period bss 6 2 beacon dtim-period bss 7 2 beacon dtim-period bss 8 2 wlan wlan1 bss 1 primary WM3400-880DA7(config-profile-default-WM3400-if-radio1)# beacon Configures radio beacon parameters dtim-period Configures the radio Delivery Traffic Indication Message (DTIM) interval. A DTIM is a message that informs wireless clients about the presence of buffered multicast or broadcast data. The message is generated within the periodic beacon at a frequency specified by the DTIM interval. <1-50> Configures a single value to use on the radio. Specify a value between 1 and 50. bss <1-8> <1-50> Configures a separate DTIM for a Basic Service Set (BSS) on a radio <1-8> Sets the BSS from 1 - 8 <1-50> Sets the BSS DTIM from 1 - 50 period [50|100|200] Configures the beacon period 50 Configures 50 K-uSec interval between beacons 100 Configures 100 K-uSec interval between beacons (default) 200 Confgiures 200 K-uSec interval between beacons
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1077 Related Commands channel interface-radio Instance Configures a radios channel of operation Supported on the following platforms: WM3411 Syntax channel [smart|12|3|4|-------] Parameters channel [smart|12|3|4|-------] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#channel 1 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 channel 1 beacon period 50 beacon dtim-period bss 1 2 beacon dtim-period bss 2 20 beacon dtim-period bss 3 2 beacon dtim-period bss 4 2 beacon dtim-period bss 5 2 beacon dtim-period bss 6 2 beacon dtim-period bss 7 2 beacon dtim-period bss 8 2 wlan wlan1 bss 1 primary WM3400-880DA7(config-profile-default-WM3400-if-radio1)# no Resets beacon parameters to default smart|12|3|4|-------] Uses Smart RF to assign a channel (uses uniform spectrum spreading if Smart RF is not enabled) 1 Channel 1 in 20Mhz 2 Channel 1 in 20Mhz
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1078 Related Commands data-rates interface-radio Instance Configures the 802.11 data rates on this radio Supported on the following platforms: WM3411 Syntax data-rates [b-only|g-only|a-only|bg|bgn|gn|an|default|custom] data-rates [b-only|g-only|a-only|bg|bgn|gn|an|default] data-rates custom [1|2|5.5|6|9|11|12|18|24|36|48|54|mcs0-7|mcs8-15| mcs0-15|basic-1|basic-2| basic-5.5|basic-6|basic-9|basic-11|basic- 12| basic-18|basic-24|basic-36|basic-48|basic-54|basic-mcs0-7]] Parameters data-rates [b-only|g-only|a-only|bg|bgn|gn|an|default] no Resets a radios channel of operation b-only Supports operation in the 11b only mode g-only Uses rates that support operation in the 11g only mode a-only Uses rates that support operation in the 11a only mode bg Uses rates that support both 11b and 11g wireless clients bgn Uses rates that support 11b, 11g and 11n wireless clients gn Uses rates that support 11g and 11n wireless clients an Uses rates that support 11a and 11n wireless clients default Enables the default data rates according to the radios band of operation
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1079 data-rates custom [1|2|5.5|6|9|11|12|18|24|36|48|54|mcs0-7|mcs8-15| mcs0-15|basic-1|basic-2| basic-5.5|basic-6|basic-9|basic-11|basic-12| basic-18|basic-24|basic-36|basic-48|basic-54|basic-mcs0-7] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#data-rates b-only WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 channel 1 data-rates b-only wlan wlan1 bss 1 primary aggregation ampdu tx-only custom Configures a list of data rates by specifying each rate individually. Use 'basic-' prefix before a rate to indicate its used as a basic rate (For example, 'data-rates custom basic-1 basic-2 5.5 11') 1 1-Mbps 2 2-Mbps 5.5 5.5-Mbps 6 6-Mbps 9 9-Mbps 11 11-Mbps 12 12-Mbps 18 18-Mbps 24 24-Mbps 36 36-Mbps 48 48-Mbps 54 54-Mbps mcs0-7 Modulation and Coding Scheme 0-7 mcs8-15 Modulation and Coding Scheme 8-15 mcs0-15 Modulation and Coding Scheme 0-15 basic-1 Basic 1-Mbps basic-2 Basic 2-Mbps basic-5.5 Basic 5.5-Mbps basic-6 Basic 6-Mbps basic-9 Basic 9-Mbps basic-11 Basic 11-Mbps basic-12 Basic 12-Mbps basic-18 Basic 18-Mbps basic-24 Basic 24-Mbps basic-36 Basic 36-Mbps basic-48 Basic 48-Mbps basic-54 Basic 54-Mbps basic-mcs0-7 Modulation and Coding Scheme 0-7 as a basic rate
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1080 antenna-mode 2x2 airtime-fairness prefer-ht ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#data-rates custom basic-mcs0-7 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary aggregation ampdu tx-only antenna-mode 2x2 airtime-fairness prefer-ht ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands description interface-radio Instance Defines a description for the selected radio Supported on the following platforms: WM3411 Syntax description <WORD> Parameters description <WORD> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#description primary radio to use WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 no Resets the 802.11 data rates on a radio <WORD> Defines a description for the selected radio
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1081 description primary\ radio\ to\ use channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary aggregation ampdu tx-only antenna-mode 2x2 airtime-fairness prefer-ht ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands dynamic-chain-selection interface-radio Instance Enables automatic antenna mode selection (single antenna for non-11n transmit rates) Supported on the following platforms: WM3411 Syntax dynamic-chain-selection Parameters None Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#dynamic-chain- selection WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary aggregation ampdu tx-only antenna-mode 2x2 dynamic-chain-selection airtime-fairness prefer-ht ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# no Removes a radios description
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1082 Related Commands guard-interval interface-radio Instance Configures the 802.11n guard interval. A guard interval ensures distinct transmissions do not interfere with one another. It provides immunity to propagation delays, echoes and reflection of radio signals. Supported on the following platforms: WM3411 Syntax guard-interval [any|long] Parameters guard-interval [any|long] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary guard-interval long aggregation ampdu tx-only antenna-mode 2x2 dynamic-chain-selection airtime-fairness prefer-ht ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# no Resets automatic antenna mode selection to default any Enables the radio to use any short (400nSec) or long (800nSec) guard interval long Enables the use of long guard interval (800nSec)
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1083 Related Commands lock-rf-mode interface-radio Instance Retains user configured RF mode settings for the selected radio Supported on the following platforms: WM3411 Syntax lock-rf-mode Parameters None Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#lock-rf-mode WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary guard-interval long aggregation ampdu tx-only antenna-mode 2x2 dynamic-chain-selection airtime-fairness prefer-ht lock-rf-mode ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands max-clients interface-radio Instance no Resets the 802.11n guard interval to default no Allows Smart RF to change a radios RF mode settings
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1084 Configures the maximum number of wireless clients allowed to associate with this radio Supported on the following platforms: WM3411 Syntax max-clients <0-256> Parameters max-clients <0-256> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#max-clients 100 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 data-rates custom basic-mcs0-7 wlan wlan1 bss 1 primary guard-interval long aggregation ampdu tx-only antenna-mode 2x2 dynamic-chain-selection max-clients 100 airtime-fairness prefer-ht lock-rf-mode ack-timeout 35 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands mesh interface-radio Instance Use this command to configure radio mesh parameters. A Wireless Mesh Network (WMN) is a network of radio nodes organized in a mesh topology. It consists of mesh clients, mesh routers, and gateways. <0-256> Configures the maximum number of clients allowed to associate with a radio. Specify a value from 0 - 256. no Resets the maximum number of wireless clients allowed to associate with a radio
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1085 Supported on the following platforms: WM3411 Syntax mesh [client|links|portal|preferred-peer] mesh [client|links <1-6>|portal|preferred-peer <1-6> <MAC>] Parameters mesh [client|links <1-6>|portal|preferred-peer <1-6> <MAC>] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#mesh preferred-peer 2 11-22-33-44-55-66 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary antenna-gain 12.0 guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# mesh Configures radio mesh parameters, such as maximum number of mesh links, preferred peer device, client operations etc. client Enables operation as a client (Scans for mesh portals or nodes that have connectivity to portals and connects through them) links <1-6> Configures the maximum number of mesh links a radio attempts to create <1-6> Sets the maximum number of mesh links from 1 - 6 portal Enables operation as a portal (Begins beaconing immediately, accepting connections from other mesh nodes, typically the node with a connection to the wired network) preferred-peer <1-6> <MAC> Configures a preferred peer device <1-6> Configures the priority at which the peer node will be added <MAC> Sets the MAC address of the preferred peer device (Ethernet MAC of either an AP or a wireless controller with onboard radios)
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1086 Related Commands no interface-radio Instance Negates a command or resets settings to their default. When used in the config WM3400 radio Interface mode, the no command disables or resets radio interface settings. Supported on the following platforms: WM3411 Syntax no <parameter> Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#no ? ack-timeout Reset the 802.11 ACK timeout to default aggregation Configure 802.11n aggregation related parameters airtime-fairness Disable fair access to medium for clients, provide access in a round-robin mode antenna-gain Reset the antenna gain of this radio to default antenna-mode Reset the antenna mode (number of transmit and receive antennas) on the radio to its default beacon Configure beacon parameters channel Reset the channel of operation of this radio to default data-rates Reset radio data rate configuration to default description Reset the description of the radio to its default dynamic-chain-selection Use the configured transmit antenna mode for all clients guard-interval Configure default value of 802.11n guard interval (long: 800nSec) no Disables mesh mode operation of the selected radio
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1087 lock-rf-mode Allow smart-rf to change rf-mode setting for this radio max-clients Maximum number of wireless clients allowed to associate mesh Disable mesh mode operation of the radio non-unicast Configure handling of non-unicast frames off-channel-scan Disable off-channel scanning on the radio placement Reset the placement of the radio to its default power Reset the transmit power of this radio to default preamble-short Disable the use of short-preamble on this radio probe-response Configure transmission parameters for Probe Response frames radio-tap-mode Configure the radio-tap mode of operation for this radio rf-mode Reset the RF mode of operation for this radio to default (2.4GHz on radio1, 5GHz on radio2, sensor on radio3) rifs Configure Reduced Interframe Spacing (RIFS) parameters rts-threshold Reset the RTS threshold to its default (2347) shutdown Re-enable the selected interface sniffer-redirect Disable capture and redirection of packets use Set setting to use wireless-client Configure wireless client related parameters wlan Disable a wlan from this radio service Service Commands WM3400-880DA7(config-profile-default-WM3400-if-radio1)# The radio interface settings before the execution of the no command: WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 description primary\ radio\ to\ use channel 1 mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary antenna-gain 12.0 guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# The radio interface settings before the execution of the no command: WM3400-880DA7(config-profile-default-WM3400-if-radio1)#no channel WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#no antenna-gain WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#no description WM3400-880DA7(config-profile-default-WM3400-if-radio1)#
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1088 WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)#
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1089 Related Commands non-unicast interface-radio Instance Configures the handling of non unicast frames on this radio. Enables the forwarding of multicast and broadcast frames by this radio. ack-timeout Configures the 802.11 ACK timeout period aggregation Configures 802.11n aggregation parameters airtime-fairness Enables equal access for wireless clients based on their airtime usage antenna-gain Configures the radio antenna gain antenna-mode Configures the radio antenna mode (the number of transmit and receive antennas) beacon Configure beacon parameters channel Configures a radio channel of operation data-rates Configures 802.11 data rates on a radio description Defines a radios description dynamic-chain-selection Enables automatic antenna mode selection (single antenna for non-11n transmit rates) guard-interval Configures the 802.11n guard interval lock-rf-mode Retains user configured radio RF mode settings max-clients Configures the maximum number of wireless clients allowed to associate with a radio mesh Enables this radio to operate in the mesh mode non-unicast Configures the handling of radio non unicast frames off-channel-scan Enables radio off channel scanning parameters placement Configures the location where a radio is deployed power Configures the radio transmit power preamble-short Enables the use of short preamble on a radio probe-response Configures transmission parameters for probe response frames radio-tap-mode Configures the radio tap mode of operation for this radio rf-mode Configures the radio RF mode rifs Configures radio RIFS parameters rts-threshold Configures the radio Request to Send (RTS) threshold value shutdown Terminates or shutsdown a radio interface sniffer-redirect Captures and redirects packets to an IP address running a packet capture/ analysis tool use Enables the use of an association ACL policy and a radio QoS policy by an interface wireless-client Configures wireless client parameters wlan Enables a WLAN on this radio service Service commands are used to view and manage the wireless controller configuration in all modes
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1090 Supported on the following platforms: WM3411 Syntax non-unicast [forwarding|queue|tx-rate] non-unicast forwarding [follow-dtim|power-save-aware] non-unicast queue [<1-200>|bss] non-unicast queue [<1-200>|bss <1-8> <1-200>] non-unicast tx-rate [bss <1-8>|dynamic-all|dynamic-basic|highest- basic|lowest-basic] non-unicast tx-rate bss <1-8> [dynamic-all|dynamic-basic|highest- basic|lowest-basic] Parameters non-unicast forwarding [follow-dtim|power-save-aware] non-unicast queue [<1-200>|bss <1-8> <1-200>] non-unicast tx-rate [bss <1-8>|dynamic-all|dynamic-basic|highest-basic| lowest-basic] non-unicast Configures the support of non unicast frames forwarding Configures multicast and broadcast frame forwarding on this radio follow-dtim Specifies frames always wait for the DTIM interval to time out. The DTIM interval is configured using the beacon command power-save-aware Enables immediate forwarding of frames if all associated wireless clients are in the power save mode non-unicast Configures the support of non unicast frames queue Configures the number of broadcast packets queued per BSS on this radio. This command also enables you to override the default on a specific BSS. <1-200> Specify a number from 1 - 200. bss <1-8> <1-200> Overrides the default on a specified BSS <1-8> Select the BSS to override the default value. <1-200> Specify the number of broadcast packets queued for the selected BSS. non-unicast Configures the support of non unicast frames tx-rate Configures the transmission data rate for broadcast and multicast frames bss <1-8> Overrides the default value on a specific BSS <1-8> Select the BSS to override the default value. dynamic-all Dynamically selects a rate from all supported rates based on current traffic conditions
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1091 Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#non-unicast queue bss 2 3 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#non-unicast tx-rate bss 1 dynamic-all WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary non-unicast tx-rate bss 1 dynamic-all non-unicast tx-rate bss 2 highest-basic non-unicast tx-rate bss 3 highest-basic non-unicast tx-rate bss 4 highest-basic non-unicast tx-rate bss 5 highest-basic non-unicast tx-rate bss 6 highest-basic non-unicast tx-rate bss 7 highest-basic non-unicast tx-rate bss 8 highest-basic non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands off-channel-scan interface-radio Instance Enables a radios off channel scanning parameters dynamic-basic Dynamically selects a rate from all supported basic rates based on current traffic conditions highest-basic Uses the highest configured basic rate lowest-basic Uses the lowest configured basic rate no Resets the handling of non unicast frames to its default
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1092 Supported on the following platforms: WM3411 Syntax off-channel-scan {channel-list|sniffer-redirect} off-channel-scan {channel-list [2.4Ghz|5Ghz] {<CHANNEL-LIST>}} off-channel-scan {sniffer-redirect <IP>} Parameters off-channel-scan {channel-list [2.4Ghz|5Ghz] {<CHANNEL-LIST>}} off-channel-scan {sniffer-redirect <IP>} Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#off-channel-scan channel-list 2.4GHz 1 WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 non-unicast tx-rate bss 1 dynamic-all non-unicast tx-rate bss 2 highest-basic non-unicast tx-rate bss 3 highest-basic non-unicast tx-rate bss 4 highest-basic non-unicast tx-rate bss 5 highest-basic non-unicast tx-rate bss 6 highest-basic non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# off-channel-scan Enables off channel scanning parameters. These parameters are optional, and the system configures default settings if no values are specified. channel-list [2.4GHz|5GHz] Optional. Specifies the channel list to scan 2.4GHZ Selects the 2.4GHz band 5GHz Selects the 5GHz band <channel-list> Optional. Specifies a list of 20MHz or 40MHz channels for the selected band (the channels are separated by commas or hyphens) off-channel-scan Enables off channel scanning parameters. These parameters are optional, and the system configures default settings if no values are specified. sniffer-redirect <IP> Optional. Captures and redirects packets to an IP address running a packet capture analysis tool <IP> Specify the destination device IP address.
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1093 Related Commands placement interface-radio Instance Defines the location where the radio is deployed Supported on the following platforms: WM3411 Syntax placement [indoor|outdoor] Parameters placement [indoor|outdoor] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#placement outdoor WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 placement outdoor mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands power interface-radio Instance Configures the transmit power on this radio no Disables radio off channel scanning indoor Radio is deployed indoors (uses indoor regulatory rules) outdoor Radio is deployed outdoors (uses outdoor regulatory rules) no Resets a radios deployment location
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1094 Supported on the following platforms: WM3411 Syntax power [<1-27>|smart] Parameters power [<1-27>|smart] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#power 12 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 power 12 placement outdoor mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands preamble-short interface-radio Instance Enables the use of short preamble on this radio Supported on the following platforms: WM3411 Syntax preamble-short power Configures a radios transmit power <1-27> Transmits power in dBm (actual power could be lower based on regulatory restrictions) smart Smart RF determines the optimum power no Resets a radios transmit power
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1095 Parameters None Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#preamble-short WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 power 12 placement outdoor mesh preferred-peer 2 11-22-33-44-55-66 wlan wlan1 bss 1 primary preamble-short guard-interval long WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands probe-response interface-radio Instance Configures transmission parameters for probe response frames. Supported on the following platforms: WM3411 Syntax probe-response [rate|retry] probe-response rate [follow-probe-request|highest-basic|lowest-basic] Parameters probe-response retry probe-response rate [follow-probe-request|highest-basic|lowest-basic] no Disables the use of short preamble on a radio probe-response Configures transmission parameters for probe response frames retry Retransmits probe response if no acknowledgement is received from the client probe-response Configures transmission parameters for probe response frames rate Configures the data rates at which the probe responses are transmitted follow-probe-request Transmits probe responses at the same rate the request was received
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1096 Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#probe-response rate follow-probe-request WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands radio-tap-mode interface-radio Instance Configures the radio tap mode for this radio Supported on the following platforms: WM3411 Syntax radio-tap-mode [inline|off|promiscuous] Parameters Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#radio-tap-mode promiscuous WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 highest-basic Uses the highest configured basic rate lowest-basic Uses the lowest configured basic rate no Resets transmission parameters for probe response frames radio-tap-mode Configures the radio tap mode inline Enables the sharing of WLAN packets serviced by this radio (matching the BSSID of the radio) off Disables radio share (no packets shared with WIPS sensor module) promiscuous Enables the sharing of packets received in promiscuous mode without filtering based on BSSID
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1097 non-unicast queue bss 4 50 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 radio-tap-mode promiscuous WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands rf-mode interface-radio Instance Configures the radio RF mode Supported on the following platforms: WM3411 Syntax rf-mode [2.4GHz-wlan|5GHz-wlan|sensor] Parameters rf-mode [2.4GHz-wlan|5GHz-wlan|sensor] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#rf-mode sensor WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 rf-mode sensor wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 no Resets the radio tap mode for this radio to its default rf-mode Configures the radio RF mode 2.4GHz-wlan Provides WLAN service in the 2.4GHz bandwidth 5GHz-wlan Provides WLAN service in the 5GHz bandwidth sensor Operates as a sensor radio. Configures this radio to function as a scanner, providing scanning services on both 2.4GHz and 5GHz bands. The radio does not provide WLAN services.
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1098 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands rifs interface-radio Instance Configures Reduced Interframe Spacing (RIFS) parameters on this radio Supported on the following platforms: WM3411 Syntax rifs [none|rx-only|tx-only|tx-rx] Parameters rifs [none|rx-only|tx-only|tx-rx] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#rifs tx-only WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 rf-mode sensor wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 rifs tx-only non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 non-unicast queue bss 5 50 no Resets the RF mode for a radio to its default rifs Configures RIFS parameters none Disables support for RIFS rx-only Supports RIFS possession only tx-only Supports RIFS transmission only tx-rx Supports both RIFS transmission and possession
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1099 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands rts-threshold interface-radio Instance Configures the RTS threshold value on this radio Supported on the following platforms: WM3411 Syntax rts-threshold <0-2347> Parameters rts-threshold <0-2347> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#rts-threshold 100 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 rf-mode sensor rts-threshold 100 wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 rifs tx-only non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# no Disables radio RIFS parameters <0-2347> Specify the RTS threshold value from 0 - 2347 bytes
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1100 Related Commands shutdown interface-radio Instance Terminates or shuts down a radio interface Supported on the following platforms: WM3411 Syntax shutdown Parameters None Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#shutdown WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands sniffer-redirect interface-radio Instance Captures and redirects packets to an IP address running a packet capture/analysis tool Supported on the following platforms: WM3411 Syntax sniffer-redirect <IP> channel [1|1+|10|10-|100--------165] no Resets a radios RTS threshold to its default (2347) no Enables a disabled radio interface
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1101 Parameters sniffer-redirect <IP> channel [1|1+|10|10---------165] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#sniffer-redirect 172.16.10.13 channel ? 1 Channel 1 in 20Mhz 1+ Channel 1 as primary, Channel 5 as extension 10 Channel 10 in 20Mhz 10- Channel 10 as primary, Channel 6 as extension 100 Channel 100 in 20Mhz --------------------------------------------------------------------------- ----------------------------------------------------------------------- WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands use interface-radio Instance The use command enables the use of an association ACL policy and a radio QoS policy by this radio interface Supported on the following platforms: WM3411 Syntax use [association-acl-policy|radio-qos-policy] use [association-acl-policy <ASSOC-ACL-POLICY>|radio-qos-policy <RADIO-QOS- POLICY>] sniffer-redirect Captures and redirects packets to an IP address running a packet capture/ analysis tool <IP> Specify the IP address of the device running the capture/analysis tool [1|1+|10|10-|100|---------- 165] Specify the channel to capture packets 1 Channel 1 in 20Mhz 1+ Channel 1 as primary, Channel 5 as extension 10 Channel 10 in 20Mhz 10- Channel 10 as primary, Channel 6 as extension 100 Channel 100 in 20Mhz no Disables capture and redirection of packets
Chapter 24: Interface Radio Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1102 Parameters use [association-acl-policy <ASSOC-ACL-POLICY>| radio-qos-policy <RADIO-QOS-POLICY>] Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#use association-acl- pol icy test1 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 rf-mode sensor rts-threshold 100 wlan wlan1 bss 1 primary off-channel-scan channel-list 2.4GHz 1 rifs tx-only use association-acl-policy test1 non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands wireless-client interface-radio Instance Configures wireless client parameters Supported on the following platforms: WM3411 Syntax wireless-client tx-power <0-20> association-acl-policy Uses a specified association ACL policy with this radio interface <ASSOC-ACL-POLICY> Specify the association ACL policy name. radio-qos-policy Uses a specified radio QoS policy with this radio interface <RADIO-QoS-POLICY> Specify the radio QoS policy name no Disables the use of the specified association ACL policy and radio QoS policy
interface-radio Instance Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1103 Parameters wireless-client tx-power <0-20> Example WM3400-880DA7(config-profile-default-WM3400-if-radio1)#wireless-client tx- power 20 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# WM3400-880DA7(config-profile-default-WM3400-if-radio1)#show context interface radio1 rf-mode sensor rts-threshold 100 wlan wlan1 bss 1 primary wireless-client tx-power 20 off-channel-scan channel-list 2.4GHz 1 rifs tx-only use association-acl-policy test1 non-unicast queue bss 1 50 non-unicast queue bss 2 3 non-unicast queue bss 3 50 non-unicast queue bss 4 50 non-unicast queue bss 5 50 non-unicast queue bss 6 50 non-unicast queue bss 7 50 non-unicast queue bss 8 50 WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands wlan interface-radio Instance Enables a WLAN on this radio Supported on the following platforms: WM3411 Syntax wlan <WLAN> {bss|primary} wlan <WLAN> bss <1-8> {primary} wireless-client Configures wireless client parameters tx-power <0-20> Configures the transmit power indicated to wireless clients <0-20> Specify transmit power from 0 - 20 dBm no Resets the transmit power indicated to wireless clients
probe-response rate highest-basic WM3400-880DA7(config-profile-default-WM3400-if-radio1)# Related Commands <WLAN> {bss <1-8> |primary} Specify the WLAN name (it must have been already created and configured) bss <1-8> Optional. Provide a specific BSS for the radio where the WLAN has to be mapped <1-8> Specify the BSS number. primary Optional. Uses the WLAN as the primary WLAN when multiple WLANs exist on the BSS no Disables a WLAN on a radio
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1105 C H A P T E R 25 Firewall Logging This chapter summarizes firewall logging commands within the CLI. The firewall uses logging to send system messages to one or more logging destinations, where they can be collected, archived and reviewed. Set the logging level to define which messages are sent to each of the target destinations. Logging messages can be sent to any of the following destinations: The firewall console Telnet or SSH session to the firewall A temporary buffer internal to the firewall Syslog server E-mail addresses An FTP server
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1106 Firewall Log Terminology and Syslog Severity Levels Date format in Syslog messages The following output displays the wireless controller date in proper format: WM3700-81916A(config)#Jul 25 11:09:00 2011: USER: cfgd: deleting session 4 WM3700-81916A(config)# WM3700-81916A(config)#Jul 25 11:09:17 2011: USER: cfgd: deleting session 5 The date format is Month <MMM> Date <DD> Time <HH:MM:SS> Year <YYYY> Month is Jul Date is 25 Time is 11:09:00 Year is 2011 To generate a date log, enable logging For example, the following command has to be executed: wm3400-34710C8#clock set 11:09:17 25 Jul 2011 Abbreviation Description FTP File transfer protocol ACL Access control list Src MAC Source MAC address Dest MAC Destination MAC address LOGRULEHIT ACL rule applied PKT DROP Packet drop Src IP Source IP address Dest IP / Dst IP Destination IP address FWSTARTUP Firewall enabled DP Destination port SP Source port Matched Temporary Rule This is a internal rule created to allow data traffic Syslog Severity Level as Message Severity Level as Numeric Description emergency 0 System is unusable alert 1 Immediate action needed critical 2 Critical condition error 3 Error condition warning 4 Warning condition notification 5 Normal but significant condition informational 6 Informational message debugging 7 Debugging message
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1107 wm3400-34710C8# FTP data connection log An ACL rule has to be applied and logging has to be enabled to generate a FTP data collection log. The FTP connection is Control Connection Jul 25 11:10:17 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Allow Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00- 15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.2.102 Proto:6 Src Port:3014 Dst Port:21 Date is Jul 25 Time is 11:10:17 Year is 2011 Module name is DATAPLANE Syslog Severity level is 5 Log ID is LOGRULEHIT Log Message is Matched ACL The Matching ACL is FTPuser IP Rule sequence number is O Disposition is Allow Packet Source MAC Address is 00-19-B9-6B-DA-77 Destination MAC Address is <00-15-70-81-91-6A> Ethertype is 0x0800 Source IP Address is 192.168.1.99 Destination IP Address is 192.168.2.102 Protocol Type is 6 Source Port is 3014D Destination Port is 21 NOTE The same terminology is used across all logs. The Data Connection in Active Mode Jul 25 11:10:19 2011: %DATAPLANE-5-LOGRULEHIT: Matched Temporary Rule of FTP ALG. Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.1.99 Proto:6 Src Port:20 Dst Port:3017. The Data Connection in Passive Mode Jul 25 11:14:31 2011: %DATAPLANE-5-LOGRULEHIT: Matched Temporary Rule of FTP ALG. Disposition:Allow Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.2.102 Proto:6 Src Port:3033 Dst Port:3894. For example, wm3400-34710C8(config-mac-acl-test)#permit any any log rule-precedence 25
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1108 wm3400-34710C8(config-mac-acl-test)# UDP packets log In both DHCP release and DHCP renew scenarios, the destination port 67 is logged. DHCP Release Jul 25 11:57:43 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:172.16.31.196 Proto:17 Src Port:68 Dst Port:67. DHCP Renew Jul 25 11:58:48 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<FF-FF-FF-FF-FF-FF> Ethertype:0x0800 Src IP:0.0.0.0 Dst IP:255.255.255.255 Proto:17 Src Port:68 Dst Port:67. To generate a UDP packet log, an ACL rule has to be applied to UDP packets, and logging has to be enabled. For example, wm3400-34710C8(config-ip-acl-test)#permit udp any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)# ICMP type logs The example below displays an ICMP Type as 13 and an ICMP Code as 0: Jul 25 12:00:00 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.1.103 Proto:1 ICMP Type:13 ICMP Code:0. The below example displays an ICMP Type as 15 and an ICMP Code as 0: Jul 25 12:00:07 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Allow Packet Src MAC:<00-60-80-B0-C3-B3> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.104 Dst IP:192.168.2.102 Proto:1 ICMP Type:15 ICMP Code:0. The below example displays an ICMP Type as 17 and an ICMP Code as 0: Jul 25 12:00:25 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.1.103 Proto:1 ICMP Type:17 ICMP Code:0. The below example displays an ICMP Type as 18 and an ICMP Code as 0:
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1109 Jul 25 12 01:00:24 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 0 and ICMP type 18. Reason: no flow matching payload of ICMP Reply. Module name is DATAPLANE Syslog Severity level is 5 Log ID is ICMPPKTDROP Log Message is Dropping ICMP Packet To generate an ICMP log, an ACL rule has to be applied on ICMP packets, and logging has to be enabled. For example, the following commands have to be executed: wm3400-34710C8(config-ip-acl-test)#permit icmp any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)# ICMP type logs The following example displays an ICMP Type as 3 and a Code as 3: Jul 25 12:03:00 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 3 and ICMP type 3. Reason: no flow matching payload of ICMP Error. Module name is DATAPLANE Syslog Severity level is 5 Log ID is ICMPPKTDROP Log Message is Dropping ICMP Packet The following example displays an ICMP Type as 4 and a Code as 0: Jul 25 12:04:06 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 0 and ICMP type 4. Reason: ICMP dest IP does not match inner source IP. The following example displays an ICMP Type as 5 and a Code as 0: Jul 25 12:05:00 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 0 and ICMP type 5. Reason: ICMP dest IP does not match inner source IP. The following example displays an ICMP type as 11 and a Code as 0: Jul 25 12:06:00 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.2.102 to 192.168.1.103, with ProtocolNumber:1 ICMP code 0 and ICMP type 11. Reason: ICMP dest IP does not match inner source IP. The following example displays an ICMP type as 14 and a Code as 0:
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1110 Jul 25 12:07:00 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 0 and ICMP type 14. Reason: no flow matching payload of ICMP Reply. The following example displays an ICMP type as 16 and a Code as 0: Jul 25 12:10:11 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 0 and ICMP type 16. Reason: no flow matching payload of ICMP Reply. To generate an ICMP log, logging has to be enabled. For example, the following commands has to be executed: wm3400-34710C8(config-fw-policy-default)#logging icmp-packet-drop all wm3400-34710C8(config-fw-policy-default)# Raw IP Protocol logs The following example displays a TCP header length as less than 20 bytes: Jul 25 12:11:50 2011: %DATAPLANE-4-DOSATTACK: INVALID PACKET: TCP header length less than 20 bytes : Src IP : 192.168.2.102, Dst IP: 192.168.1.104, Src Mac: 00-11-25-14-D9-E2, Dst Mac: 00-15-70-81- 91-6A, Proto = 6. Module name is DATAPLANE Syslog Severity level is 4 Log ID is DOSATTACK Log Message is INVALID PACKET Jul 25 12:12:00 2011: %DATAPLANE-5-MALFORMEDIP: Dropping IPv4 Packet from 192.168.2.102 to 192.168.1.104 Protocol Number: 6. Reason: malformed TCP header. Module name is DATAPLANE Syslog Severity level is 5 Log ID is MALFORMEDIP Log Message is Dropping IPv4Packet To generate a raw IP protocol log, logging has to be enabled. For example, the following commands has to be executed: wm3400-34710C8(config-fw-policy-default)# logging verbose wm3400-34710C8(config-fw-policy-default)# wm3400-34710C8(config-fw-policy-default)# logging malformed-packet-drop all wm3400-34710C8(config-fw-policy-default)# When logging verbose is enabled, the log is displayed as:
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1111 Jul 25 12:15:21 2011: %DATAPLANE-5-MALFORMEDIP: Dropping IPv4 Packet from 192.168.0.91 to 192.168.0.1 Protocol Number: 6 SrcPort: 22616 DstPort: 22616 Reason: no matching TCP flow. Module name is DATAPLANE Syslog Severity level is 5 Log ID is MALFORMEDIP Log Message is Dropping IPv4Packet Raw IP Protocol logs The following example displays TCP without data: Jul 25 12:16:50 2011: %DATAPLANE-4-DOSATTACK: INVALID PACKET: TCP header length less than 20 bytes : Src IP : 192.168.2.102, Dst IP: 192.168.1.104, Src Mac: 00-11-25-14-D9-E2, Dst Mac: 00-15-70-81- 91-6A, Proto = 6. Jul 25 12:16:55 2011: %DATAPLANE-5-MALFORMEDIP: Dropping IPv4 Packet from 192.168.2.102 to 192.168.1.104 Protocol Number: 6. Reason: malformed TCP header. To generate a raw IP protocol log, logging has to be enabled. For example, the following commands has to be executed: wm3400-34710C8(config-fw-policy-default)# logging verbose wm3400-34710C8(config-fw-policy-default)# wm3400-34710C8(config-fw-policy-default)# logging rawip-packet-drop all wm3400-34710C8(config-fw-policy-default)# When logging verbose is enabled, the log is displayed as: Jul 25 12:20:30 2011: %DATAPLANE-4-DOSATTACK: INVALID PACKET: TCP header length less than 20 byt es : Src IP : 192.168.0.91, Dst IP: 192.168.0.1, Src Mac: 00-16-36-05-72-2A, Dst Mac: 00-23-68-22-C8- 6E, Proto = 6. Jul 25 12:22:49 2011: %DATAPLANE-5-MALFORMEDIP: Dropping IPv4 Packet from 192.168.0.91 to 192.168.0.1 Protocol Number: 6 . Reason: malformed TCP header. Module name is DATAPLANE Syslog Severity level is 4 Log ID is DOSATTACK Log Message is INVALID PACKET Firewall startup log The following example displays an enabled firewall. A firewall enabled message is displayed in bold. System bootup time (via /proc/uptime) was 93.42 42.52
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1112 Please press Enter to activate this console. May 19 20:10:09 2010: %NSM-4-IFUP: Interface vlan2 is up Jul 25 12:25:09 2011: KERN: vlan2: add 01:00:5e:00:00:01 mcast address to master interface. Jul 25 12:25:09 2011: %NSM-4-IFUP: Interface vlan172 is up Jul 25 12:25:09 2011: KERN: vlan172: add 01:00:5e:00:00:01 mcast address to master interface. Jul 25 12:25:09 2011: %PM-6-PROCSTART: Starting process "/usr/sbin/lighttpd" Jul 25 12:25:09 2011: %FILEMGMT-5-HTTPSTART: lighttpd started in external mode with pid 0 Jul 25 12:25:09 2011: %DAEMON-3-ERR: dhcrelay: interface allocate : vlan1 Jul 25 12:25:09 2011: %USER-5-NOTICE: FILEMGMT[1086]: FTP: ftp server stopped Jul 25 12:25:09 2011: %DAEMON-3-ERR: dhcrelay: interface allocate : vlan1 Jul 25 12:25:09 2011: %DAEMON-3-ERR: dhcrelay: interface allocate : vlan1 Jul 25 12:25:09 2011: %DAEMON-3-ERR: dhcrelay: interface allocate : vlan2 Jul 25 12:25:09 2011: %DOT11-5-COUNTRY_CODE: Country of operation configured to in [India] Jul 25 12:25:09 2011: %DIAG-6-NEW_LED_STATE: LED state message AP_LEDS_ON from module DOT11 Jul 25 12:25:09 2011: %PM-6-PROCSTART: Starting process "/usr/sbin/telnetd" Jul 25 12:25:09 2011: %AUTH-6-INFO: sshd[1422]: Server listening on 0.0.0.0 port 22. dataplane enabled CCB:21:Firewall enabled Jul 25 12:25:09 2011: %KERN-4-WARNING: dataplane enabled. Jul 25 12:25:09 2011: %DATAPLANE-5-FWSTARTUP: Firewall enabled. Jul 25 12:25:09 2011: USER: cfgd: handle_cluster_member_update Jul 25 12:25:09 2011: USER: cfgd: ignoring, no cluster configured Jul 25 12:25:09 2011: %PM-6-PROCSTART: Starting process "/usr/sbin/sshd" Manual time change log The following example displays the manual time change log. The clock is manually set to Jul 25 12:25:33 2011. Log change in time wm3400-34710C8#show clock 2011-07-25 12:25:33 UTC wm3400-34710C8# wm3400-34710C8#clock set 12:25:33 25 Jul 2011
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1113 Jul 25 12:25:33 2011: %[S1]CFGD-6-SYSTEM_CLOCK_RESET: System clock reset, Time: 2011-07-25 12:45:00[S2] wm3400-34710C8#show clock Jul 25 12:45:00 UTC 2011 wm3400-34710C8# To generate a time log, logging has to be enabled For example, the following command has to be executed: wm3400-34710C8#clock set 12:45:00 25 Jul 2011 wm3400-34710C8# Firewall ruleset log The following example displays the log changes as ACL_ATTACHED_ALTERED when an ACL Rule is applied/removed on WLAN, VLAN, GE, and PORT-CHANNEL: IP ACL IN on WLAN Attach July 28 12:48:40 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered USER: The user who is doing the change session: means the session id of the user - one user can have multiple sessions running, so this explains from which session this change was done ACL: Name of the ACL that has rules added/deleted IP ACL IN on WLAN Remove July 28 12:48:42 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. IP ACL OUT on WLAN Attach July 28 12:48:44 2011 2010: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. IP ACL OUT on WLAN Remove July 28 12:48:50 2011 2010: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered.
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1114 MAC ACL IN on WLAN Attach July 28 12:48:55 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. MAC ACL IN on WLAN Remove July 28 12:48:572011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. MAC ACL OUT on WLAN Attach July 28 12:49:00 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. MAC ACL OUT on WLAN Remove July 28 12:49:06 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to wlan ICSA-testing is getting altered. IP ACL on VLAN Attach July 28 12:49:10 201: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface vlan1 is getting altered. IP ACL on VLAN Remove July 28 12:49:12 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface vlan1 is getting altered. IP ACL on GE Port Attach July 28 12:49:15 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface ge1 is getting altered. IP ACL on GE Port Remove July 28 12:49:20 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface ge1 is getting altered. MAC ACL on GE Port Attach July 28 12:49:22 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface ge1 is getting altered.
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1115 MAC ACL on GE Port Remove July 28 12:49:24 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface ge1 is getting altered. IP ACL on Port-Channel Attach July 28 12:49:30 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface port-channel1 is getting altered. IP ACL on Port-Channel Remove July 28 12:50:00 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface port-channel1 is getting altered. MAC ACL on Port-Channel Attach July 28 12:50:01 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface port-channel1 is getting altered. MAC ACL on Port-Channel Remove July 28 12:50:05 2011: %CFGD-6-ACL_ATTACHED_ALTERED: USER: root session 3: ACL attached to interface port-channel1 is getting altered. Rule added / deleted from IP/MAC ACL Feb 26 20:32:56 2011: %CFGD-6-ACL_RULE_ALTERED: USER: admin session 3: ACL foo rule is getting altered. TCP Reset Packets log For any change in the TCP configuration, a TCP reset log is generated. The following example displays the initial TCP packets permitted before the session timedout: July 28 20:31:26 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.2.102 Proto:6 Src Port:3318 Dst Port:21. July 28 20:31:31 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.2.102 Proto:6 Src Port:3318 Dst Port:21.
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1116 ICMP Destination log The following example displays an ICMP destination as unreachable when no matching payload is found: July 28 19:57:09 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 3 and ICMP type 3. Reason: no flow matching payload of ICMP Error. July 28 19:57:09 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.1.104 to 192.168.2.102, with ProtocolNumber:1 ICMP code 3 and ICMP type 3. Reason: no flow matching payload of ICMP Error. To generate an ICMP protocol log, an ACL rule has to be applied and logging has to be enabled. For example, the following commands has to be executed: wm3400-34710C8(config-ip-acl-test)#permit icmp any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)# ICMP Packet log July 28 20:37:04 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Drop Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.1.1 Proto:1 ICMP Type:8 ICMP Code:0. July 28 20:37:08 2011: %DATAPLANE-5-ICMPPKTDROP: Dropping ICMP Packet from 192.168.2.1 to 172.16.31.196, with Protocol Number:1 ICMP code 3 and ICMP type 3. Reason: no flow matching payload of ICMP Error. To generate an ICMP protocol log, an ACL rule has to be applied and logging has to be enabled: For example, the following commands has to be executed: wm3400-34710C8(config-ip-acl-test)#permit icmp any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)# SSH connection log A SSH connection is enabled on the wireless controller using factory settings. Running primary software, version 5.0.0.0-81243X Alternate software secondary, version 5.3.0.0-048D Software fallback feature is enabled System bootup time (via /proc/uptime) was 126.10 92.38 Please press Enter to activate this console. May 19 20:47:33 2010: %DOT11-5-COUNTRY_CODE: Country of operation configured to in [India]
Firewall Log Terminology and Syslog Severity Levels Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1117 July 28 20:47:34 2011: %DIAG-6-NEW_LED_STATE: LED state message AP_LEDS_ON from module DOT11 July 28 20:47:34 2011: KERN: vlan1: add 01:00:5e:00:00:01 mcast address to master interface. July 28 20:47:34 2011: %NSM-4-IFUP: Interface vlan2 is up July 28 20:47:34 2011: KERN: vlan2: add 01:00:5e:00:00:01 mcast address to master interface. July 28 20:47:34 2011: %NSM-4-IFUP: Interface vlan172 is up July 28 20:47:34 2011: KERN: vlan172: add 01:00:5e:00:00:01 mcast address to master interface. July 28 20:47:34 2011: %DAEMON-3-ERR: dhcrelay: interface allocate: vlan1 July 28 20:47:34 2011: %PM-6-PROCSTART: Starting process "/usr/sbin/sshd" July 28 20:47:34 2011: %DAEMON-3-ERR: dhcrelay: idataplane enabled nterface allocatCCB:21:Firewall enabled e : vlan1 July 28 20:47:34 2011: %DAEMON-3-ERR: dhcrelay: interface allocate : vlan2 July 28 20:47:34 2011: %KERN-4-WARNING: dataplane enabled. July 28 20:47:34 2011: %DATAPLANE-5-FWSTARTUP: Firewall enabled. July 28 20:47:39 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Drop Packet Src MAC:<00-19-B9-6B-DA-77> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.1.99 Dst IP:192.168.1.1 Proto:6 Src Port:3327 DstPort:22. Allowed/Dropped Packets Log The following example displays disposition information regarding allow/deny packets: Allow Packets CCB:0:Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.2.1 Proto:17 Src Port:137 Dst Port:137 CCB:0:Matched ACL:ftpuser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.2.1 Proto:17 Src Port:1029 Dst Port:53 CCB:July 28 18:14:3220110: %DATAPLAN:-5-LOGRULEHIT: Matched ACL:ftpuer:aip Rule:1 Ditcposition:Allow hedacket Src MAC: 00-11-25-14-D9-A2> Dst MAC:<00-5-70-81-9C1-6A> thertLype:0x0800:Src IP:192.168..102 Dsft IP:192t168.2.1 Proto:1p Src Port:137 Dut Port:137. ser:ip Rule:1 Disposition:Allow Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.2.1 Proto:17 Src Port:1029 Dst Port:53
Chapter 25: Firewall Logging Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1118 Drop/Deny Packets CCB:0:Matched ACL:ftpuser:ip Rule:0 Disposition:Drop Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.2.1 Proto:17 Src Port:137 Dst Port:137 July 28 20:41:28 2011: %DATAPLANE-5-LOGRULEHIT: Matched ACL:ftpuser:ip Rule:0 Disposition:Drop Packet Src MAC:<00-11-25-14-D9-E2> Dst MAC:<00-15-70-81-91-6A> Ethertype:0x0800 Src IP:192.168.2.102 Dst IP:192.168.2.1 Proto:17 Src Port:137 Dst To generate an allow/deny protocol log, an ACL rule has to be applied and logging has to be enabled. For example, the following commands has to be executed: wm3400-34710C8(config-ip-acl-test)#permit ip any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)# wm3400-34710C8(config-ip-acl-test)#deny ip any any log rule-precedence 20 wm3400-34710C8(config-ip-acl-test)#
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1119 C H A P T E R 26 L2TPV3-Policy This chapter summarizes Layer 2 Tunnel Protocol Version 3 (L2TPV3) policy commands within the CLI structure. The L2TPV3 policy defines control and encapsulation protocols for tunneling different types of layer 2 frames between two IP nodes. The L2TPV3 control protocol controls dynamic creation, maintenance, and teardown of L2TP sessions. The L2TPV3 encapsulation protocol is used to multiplex and de- multiplex L2 data streams between two L2TP nodes across an IP network. Use the (config) instance to configure L2TPV3 policy parameters. To navigate to the L2TPV3 policy instance, use the following commands: wm3400-34710C8(config)#l2tpv3 policy <L2TPV3-POLICY-NAME> wm3400-34710C8(config)#l2tpv3 policy L2TPV3Policy1 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#? L2tpv3 Policy Mode commands: cookie-size Size of the cookie field present in each l2tpv3 data message hello-interval Configure the time interval (in seconds) between l2tpv3 Hello keep-alive messages exchanged in l2tpv3 control connection no Negate a command or set its defaults reconnect-attempts Maximum number of attempts to reestablish the tunnel. reconnect-interval Time interval between the successive attempts to reestablish the l2tpv3 tunnel retry-attempts Configure the maximum number of retransmissions for signaling message retry-interval Time interval (in seconds) before the initiating a retransmission of any l2tpv3 signaling message rx-window-size Number of signaling messages that can be received without sending the acknowledgement tx-window-size Number of signaling messages that can be sent without receiving the acknowledgement clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1120 revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1121 l2tpv3-policy-commands The following table summarizes L2TPV3 policy commands Command Description Reference cookie-size Configures the cookie field size for each L2TPV3 data packet page 26-1122 hello-interval Configures the time interval, in seconds, between L2TPV3 Hello keep-alive messages exchanged in L2TPV3 control connection page 26-1123 no Negates or reverts L2TPV3 tunnel commands page 26-1124 reconnect- attempts Configures the maximum number of retransmissions for signalling messages page 26-1126 reconnect- interval Configures the interval, in seconds, between successive attempts to reestablish a tunnel connection page 26-1127 retry-attempts Configures the maximum number of retransmissions for signalling messages page 26-1128 retry-interval Configures the time interval, in seconds, before initiating a retransmission of any L2TPV3 signalling message page 26-1129 rx-window-size Configures the number of signalling messages that can be received without sending an acknowledgement page 26-1130 tx-window-size Configures the number of signalling messages that can be transmitted without receiving an acknowledgement page 26-1131 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the systems running configuration to memory or terminal page 6-420
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1122 cookie-size l2tpv3-policy-commands Configures the size of the cookie field present in each L2TPV3 data packet. A tunnel cookie is a 4-byte or 8-byte signature shared between the two endpoints of a tunnel. This signature has to be configured at both the source and destination routers. If the signature at both ends do not match, the data is dropped. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax cookie-size [0|4|8] Parameters cookie-size [0|4|8] Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#cookie-size 8 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 cookie-size 8 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands cookie-size [0|4|8] Configures the cookie-field size for each data packet. Select one of the following options: 0 No cookie field present in each L2TPV3 data message (this is the default value) 4 4 byte cookie field present in each L2TPV3 data message 8 8 byte cookie field present in each L2TPV3 data message no Resets the cookie-field size to its default (0 - no cookie field present in each L2TPV3 data packet)
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1123 hello-interval l2tpv3-policy-commands Configures the time interval, in seconds, between L2TPV3 Hello keep-alive messages exchanged in L2TPV3 control connection. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax hello-interval <1-3600> Parameters hello-interval <1-3600> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#hello-interval 200 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 hello-interval 200 cookie-size 8 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands hello-interval <1-3600> Configures the time interval for L2TPV3 Hello keep-alive messages between 1 - 3600 seconds. (default is 60 seconds) no Resets the Hello keep-alive message time interval to its default of 60 seconds
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1124 no l2tpv3-policy-commands Negates or reverts L2TPV3 policy settings to default values Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax no [cookie-size|hello-interval|reconnect-attempts|reconnect-interval| retry-attempts|retry-interval|rx-window-size|tx-window-size] Parameters no [cookie-size|hello-interval|reconnect-attempts|reconnect-interval| retry-attempts|retry-interval|rx-window-size|tx-window-size] no cookie-size Resets the cookie-field size to default (0 - no cookie field present in each L2TPV3 data packet) no hello-interval Resets the Hello keep-alive message time interval to default (60 seconds no reconnect-attempts Resets the maximum number of reconnect attempts to default (0 - configures infinite attempts) no reconnect-interval Resets the interval between successive attempts to reestablish a tunnel connection to default (120 seconds) no retry-attempts Resets the maximum number of retransmissions for signalling messages to default (5 attempts) no retry-interval Resets the time interval before initiating a retransmission of any L2TPV3 signalling message to default (5 seconds) no rx-window-size Resets the number of packets that can be received without sending an acknowledgement to default (10 packets) no tx-window-size Resets the number of packets that can be transmitted without receiving an acknowledgement to default (10 packets)
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1125 Example The l2tpv3 policy settings before the no command is executed: wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 hello-interval 200 retry-attempts 10 retry-interval 30 cookie-size 8 reconnect-interval 100 reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#no hello-interval wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#no reconnect-attempts wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#no reconnect-interval wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#no retry-attempts wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#no retry-interval The l2tpv3 policy settings after the no command is executed: wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands cookie-size Configures the cookie-field size present in each L2TPV3 data packet hello-interval Configures the time interval for L2TPV3 Hello keep-alive messages reconnect-attempts Configures the maximum number of attempts made to reestablish a tunnel connection reconnect-interval Configures the interval, in seconds, between successive attempts to reestablish a tunnel connection retry-attempts Configures the maximum number of retransmissions for signalling messages between 1 - 10 retry-interval Configures the time interval, in seconds, before initiating a retransmission of any L2TPV3 signalling message rx-window-size Configures the number of packets that can be received without sending an acknowledgement tx-window-size Configures the number of packets that can be transmitted without receiving an acknowledgement
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1126 reconnect-attempts l2tpv3-policy-commands Configures the maximum number of attempts to reestablish a tunnel connection Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax reconnect-attempts <0-250> Parameters reconnect-attempts <0-250> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 hello-interval 200 cookie-size 8 reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands reconnect-attempts <0-250> Configures the maximum number of attempts to reestablish a tunnel connection between 0 - 250 (default is 0: configures infinite reconnect attempts) no Resets the maximum number of reconnect attempts to default (0: configures infinite reconnect attempts)
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1127 reconnect-interval l2tpv3-policy-commands Configures the interval, in seconds, between successive attempts to reestablish a tunnel connection Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax reconnect-interval <1-3600> Parameters reconnect-interval <1-3600> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#reconnect-interval 100 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# l2tpv3 policy L2TPV3Policy1 hello-interval 200 cookie-size 8 reconnect-interval 100 reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands reconnect-interval <1-3600> Configures the interval between successive attempts to reestablish a tunnel connection between 1 - 3600 seconds (default is 120 seconds) no Resets the interval between successive attempts to reestablish a tunnel connection to default (120 seconds)
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1128 retry-attempts l2tpv3-policy-commands Configures the maximum number of retransmissions for signalling messages. Use this command to specify how many retransmission cycles occur before determining the peer is not reachable. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax retry-attempts <1-10> Parameters retry-attempts <1-10> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#retry-attempts 10 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# fs7000-37FABE(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 hello-interval 200 retry-attempts 10 cookie-size 8 reconnect-interval 100 reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands retry-attempts <1-10> Configures the maximum number of retransmissions for signalling messages between 1 - 10 (default is 5 attempts) no Resets the maximum number of retransmissions for signalling messages to default (5 attempts)
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1129 retry-interval l2tpv3-policy-commands Configures the time interval, in seconds, before initiating a retransmission of any L2TPV3 signalling message Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax retry-interval <1-250> Parameters retry-interval <1-250> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#retry-interval 30 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#show context l2tpv3 policy L2TPV3Policy1 hello-interval 200 retry-attempts 10 retry-interval 30 cookie-size 8 reconnect-interval 100 reconnect-attempts 50 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands retry <1-250> Configures the time interval before initiating a retransmission of any L2TPV3 signalling message between 1 - 250 seconds (default is 5 seconds) no Resets the time interval before initiating a retransmission of any L2TPV3 signalling message to default (5 seconds)
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1130 rx-window-size l2tpv3-policy-commands Configures the number of signalling messages that can be received without sending an acknowledgement Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax rx-window-size <1-15> Parameters rx-window-size <1-15> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#rx-window-size 10 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands rx-window-size <1-15> Configures the number of packets that can be received without sending an acknowledgement between 1 - 15 (default is 10 packets) no Resets the number of packets that can be received without sending an acknowledgement to default (10 packets)
l2tpv3-policy-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1131 tx-window-size l2tpv3-policy-commands Configures the number of signalling messages that can be transmitted without receiving an acknowledgement Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax tx-window-size <1-15> Parameters tx-window-size <1-15> Example wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)#tx-window-size 10 wm3400-34710C8(config-l2tpv3-policy-L2TPV3Policy1)# Related Commands tx-window-size <1-15> Configures the number of packets that can be transmitted without receiving an acknowledgement between 1 - 15 (default is 10 packets) no Resets the number of packets that can be transmitted without receiving an acknowledgement to default (10 packets)
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1132 l2tpv3-tunnel-commands Use the (profile-context) instance to configure a L2TPV3 tunnel. To navigate to the tunnel configuration mode, use the following command in the profile context: wm3400-34710C8(config-profile-default-wm3400)#l2tpv3 tunnel <TUNNEL-NAME> wm3400-34710C8(config-profile-default-wm3400)#l2tpv3 tunnel Tunnel1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-Tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-Tunnel1)#? L2tpv3 Tunnel Mode commands: hostname Tunnel specific local hostname local-ip-address Configure the IP address for tunnel. If not specified, tunnel source ip address would be chosen automatically based on the tunnel peer ip address mtu Configure the mtu size for the tunnel no Negate a command or set its defaults peer Configure the l2tpv3 tunnel peers. At least one peer must be specified router-id Tunnel sepcific local router ID session Create / modify the specified l2tpv3 session use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-Tunnel1)# The following table summarizes L2TPV3 tunnel configuration commands Command Description Reference hostname Configures tunnel specific local hostname page 26-1134 local-ip- address Configures the tunnels IP address page 26-1135 mtu Configures the tunnels maximum transmission unit (mtu) size page 26-1136 no Negates or reverts L2TPV3 tunnel commands page 26-1137 peer Configures the tunnels peers page 26-1139 router-id Configures the tunnels local router ID page 26-1141 session Creates/modifies specified L2TPV3 session page 26-1142 use Configures a tunnel to use a specified L2TPV3 tunnel policy page 26-1144 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1133 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes the systems running configuration to memory or terminal page 6-420 Command Description Reference
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1134 hostname l2tpv3-tunnel-commands Configures the tunnels local hostname Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax hostname <WORD> Parameters hostname <WORD> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#hostname TunnelHost1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 hostname TunnelHost1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands hostname <WORD> Configures the tunnels local hostname <WORD> Specify the tunnels local hostname. no Removes the tunnels local hostname
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1135 local-ip-address l2tpv3-tunnel-commands Configures the tunnels source IP address. If no IP address is specified, the tunnels source IP address is automatically configured based on the tunnel peer IP address. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax local-ip-address <A.B.C.D> Parameters local-ip-address <A.B.C.D> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#local-ip-address 172.16.10.2 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 hostname TunnelHost1 local-ip-address 172.16.10.2 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands local-ip-address <A.B.C.D> Configures the L2TPV3 tunnels source IP address <A.B.C.D> Specify the tunnels IP address. Ensure that the IP address is available (or will become available - virtual IP) on an interface. Modifying a tunnels local IP address reestablishes the tunnel. no Resets the tunnels local IP address and reestablishes the tunnel
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1136 mtu l2tpv3-tunnel-commands Configures the maximum transmission unit (mtu) size for this tunnel. This value determines the packet size transmitted over this tunnel. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax mtu <128-1460> Parameters mtu <128-1460> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#mtu 1280 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 local-ip-address 172.16.10.2 mtu 1280 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands mtu <128-1460> Configures the mtu size for this tunnel between 128 - 1460 (default is 1460) no Resets the mtu size for this tunnel to default (1460)
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1137 no l2tpv3-tunnel-commands Negates or reverts L2TPV3 tunnel settings to default values Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax no [hostname|local-ip-address|mtu|peer|router-id|session|use] Parameters no [hostname|local-ip-address|mtu|peer|router-id|session|use] Example The tunnel settings before the no command is executed: wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 peer 2 hostname tunnel1peer1 udp port 100 use l2tpv3-policy l2tpv3Policy1 session tunnel1peer1session1 pseudowire-id 5000 traffic-source vlan 10-20 native- vlan 1 router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#no use l2tpv3-policy wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1) wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#no peer 2 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# no hostname Removes the tunnels local hostname no local-ip-address Resets the tunnels local IP address and reestablishes the tunnel no mtu Resets the mtu size for this tunnel to default (1460) no peer Removes the peer configured for this tunnel no router-id Removes the tunnels router ID no session Removes a session no use Removes the L2TPV3 policy configured with a tunnel and reverts to the default tunnel policy
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1138 The tunnel settings after the no command is executed: wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 session tunnel1peer1session1 pseudowire-id 5000 traffic-source vlan 10-20 native- vlan 1 router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands hostname Configures the tunnels local hostname local-ip-address Configures the tunnels source IP address mtu Configures the maximum transmission unit (mtu) size for this tunnel peer Configures the tunnels peers router-id Configures the tunnels local router ID session Creates/modifies specified L2TPV3 session use Configures a tunnel to use a specified L2TPV3 tunnel policy
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1139 peer l2tpv3-tunnel-commands Configures the L2TPV3 tunnels peers. At least one peer must be specified. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax peer <1-2> {hostname|ip-address|router-id|udp} peer <1-2> {hostname [<WORD>|any]|ip-address <A.B.C.D>| (router-id [<A.B.C.D>|<WORD>|any])|(udp port <1-65535>)} Parameters peer <1-2> {hostname [<WORD>|any]|ip-address <A.B.C.D>| (router-id [<A.B.C.D>|<WORD>|any])|(udp port <1-65535>)} peer <1-2> Configures the tunnel peer ID from 1 - 2. At any time the tunnel is established with only one peer. hostname [<WORD>|any] Specifies the peers hostname hostname [<WORD>|any] Optional. Configures the peers hostname. The hostname options are: <WORD> The fully qualified domain name (FQDN) or partial DN any Peer name is not specified. If the hostname is any this tunnel will be considered as responder only and will allow incoming connection from any host. ip-address <A.B.C.D> Optional. Configures the peers IP address in the A.B.C.D format router-id [<A.B.C.D>|<WORD>|any] The following are common to the hostname and ip-address parameters. router-id Optional. Configures the peers router-id in one of the following formats: <A.B.C.D> Peer router ID in the IP address (A.B.C.D) format <WORD> Peer router ID range (for example, 100-120) any Peer router ID is not specified. This allows incoming connection from any router ID. udp port <1-65535> The UDP option configures the encapsulation mode for this tunnel. UDP Optional. Configures UDP encapsulation (default encapsulation is IP) port <1-65535> Configures the peers UDP port running the L2TPV3 service. from 1 - 65535.
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1140 Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#peer 2 host name tunnel1peer1 udp port 100 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show contex t l2tpv3 tunnel tunnel1 peer 2 hostname tunnel1peer1 udp port 100 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands no Removes the peer configured for this tunnel
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1141 router-id l2tpv3-tunnel-commands Configures the tunnels local router ID Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax router-id [<1-4294967295>|<A.B.C.D>] Parameters router-id [<1-4294967295>|<A.B.C.D>] Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 peer 2 hostname tunnel1peer1 udp port 100 router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands router-id [<1-4294967295>|<A.B.C.D>] Configures the tunnels local router ID in one of the following formats: <1-4294967295> Router ID in the number format (from1- 4294967295) <A.B.C.D> Router ID in IP address format (A.B.C.D) no Removes the tunnels router ID
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1142 session l2tpv3-tunnel-commands Configures a sessions pseudowire ID, which describes the sessions purpose. The session established message sends this pseudowire ID to the L2TPV3 peer. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax session <L2TPV3-SESSION-NAME> pseudowire-id <1-4294967295> traffic-source vlan <VLAN-ID-RANGE> {native-vlan <1-4094>} Parameters session <L2TPV3-SESSION-NAME> pseudowire-id <1-4294967295> traffic-source vlan <VLAN-ID-RANGE> {native-vlan <1-4094>} Usage Guidelines The working status of a pseudowire is reflected by the state of the L2TPV3 session. If the corresponding session is L2TPV3 down, the pseudowire associated with it must be shut down. Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#session tun nel1peer1session1 pseudowire-id 5000 traffic-source vlan 10-20 native-vlan 1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 peer 2 hostname tunnel1peer1 udp port 100 session <L2TPV3-SESSION-NAME> Configures this sessions name pseudowire-id <1-4294967295> Configures the pseudowire ID for this session from 1- 4204067295 traffic-source vlan <VLAN-ID-RANGE> Configures VLAN as the traffic source for this tunnel <VLAN-ID-RANGE> Configures VLAN range list of traffic source. Specify the VLAN IDs as a range (for example, 10-20, 25, 30-35). native-vlan <1-4094> Optional Configures the native VLAN ID for this session, which is not tagged <1-4094> Specify the native VLAN ID from 1- 4094.
l2tpv3-tunnel-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1143 session tunnel1peer1session1 pseudowire-id 5000 traffic-source vlan 10-20 native- vlan 1 router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands no Removes a session
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1144 use l2tpv3-tunnel-commands Configures a tunnel to use a specified L2TPV3 tunnel policy Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax use l2tpv3-policy <L2TPV3-POLICY-NAME> Parameters use l2tpv3-policy <L2TPV3-POLICY-NAME> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#use l2tpv3- policy l2tpv3Policy1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)#show context l2tpv3 tunnel tunnel1 peer 2 hostname tunnel1peer1 udp port 100 use l2tpv3-policy l2tpv3Policy1 session tunnel1peer1session1 pseudowire-id 5000 traffic-source vlan 10-20 native- vlan 1 router-id 2000 wm3400-34710C8(config-profile default-wm3400-l2tpv3-tunnel-tunnel1)# Related Commands use l2tpv3-policy <L2TPV3-POLICY-NAME> Configures the L2TPV3 policy used with this tunnel <L2TPV3-POLICY-NAME> The policy name no Removes the L2TPV3 policy configured with a tunnel and reverts to the default tunnel policy
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1145 l2tpv3-manual-session-commands Use the (profile-context) instance to configure a L2TPV3 manual session. To navigate to the L2TPV3 manual session configuration mode, use the following command in the profile context: wm3400-34710C8(config-profile-default-wm3400)#l2tpv3 manual-session <SESSION-NAME> wm3400-34710C8(config-profile-default-wm3400)#l2tpv3 manual-session manualSessi on1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSession1)#? L2tpv3 Manual Session Mode commands: local-cookie The local cookie for the session local-ip-address Configure the IP address for tunnel. If not specified, tunnel source ip address would be chosen automatically based on the tunnel peer ip address local-session-id Local session id for the session mtu Configure the mtu size for the tunnel no Negate a command or set its defaults peer Configure L2TPv3 mannual session peer remote-cookie The remote cookie for the session remote-session-id Remote session id for the session traffic-source Traffic that is tunneled clrscr Clears the display screen commit Commit all changes made in this session end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSession1)# The following table summarizes L2TPV3 manual session configuration commands Command Description Reference local-cookie Configures the manual sessions local cookie field size page 26-1147 local-ip- address Configures the manual sessions local source IP address page 26-1148 local-session- id Configures the manual sessions local session ID page 26-1149 mtu Configures the mtu size for the manual session tunnel page 26-1150 no Negates or reverts L2TPV3 manual session commands to default values page 26-1137 peer Configures the manual sessions peers page 26-1154 remote-cookie Configures remote cookie for the manual session page 26-1155
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1146 remote- session-id Configures the manual sessions remote session ID page 26-1157 traffic-source Configures the traffic source that is tunnel by the manual session page 26-1158 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 6-418 write Writes the systems running configuration to memory or terminal page 6-420 Command Description Reference
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1147 local-cookie l2tpv3-manual-session-commands Configures the local cookie field size for the manual session Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax local-cookie size [4|8] <1-4294967295> {<1-4294967295>} Parameters local-cookie size [4|8] <1-4294967295> {<1-4294967295>} Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#local-cookie size 8 200 300 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-cookie size 8 200 300 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands local-cookie size [4|8] Configures the local cookie field size for this manual session. The options are: 4 4 byte local cookie field 8 8 byte local cookie field <1-4294967295> Configures the local cookie value firstword. Applies to both the 4 byte and 8 byte local cookies <1-4294967295> Optional Configures the local cookie value secondword. Applicable to only 8 byte cookies. This parameter is ignored for 4 byte cookies. no Removes the local cookie size configured for a manual session
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1148 local-ip-address l2tpv3-manual-session-commands Configures the manual sessions source IP address. If no IP address is specified, the tunnels source IP address is automatically configured based on the tunnel peer IP address. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax local-ip-address <A.B.C.D> Parameters local-ip-address <A.B.C.D> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#local-ip-address 1.2.3.4 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-cookie size 8 200 300 local-ip-address 1.2.3.4 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands local-ip-address <A.B.C.D> Configures the manual sessions source IP address in the A.B.C.D format no Resets the manual sessions local source IP address. This reestablishes the session.
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1149 local-session-id l2tpv3-manual-session-commands Configures the manual sessions local session ID Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax local-session-id <1-63> Parameters local-session-id <1-63> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#local-session-id 1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-cookie size 8 200 300 local-ip-address 1.2.3.4 local-session-id 1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands local-session-id <1-63> Configures this manual sessions local session ID from 1 - 63 no Removes the manual sessions local session ID
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1150 mtu l2tpv3-manual-session-commands Configures the MTU size for the manual session tunnel Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax mtu <128-1460> Parameters mtu <128-1460> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#mtu 200 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-cookie size 8 200 300 local-ip-address 1.2.3.4 mtu 200 local-session-id 1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands mtu <128-1460> Configures the MTU size for this manual session tunnel from 128 - 1460 (default is 1460) no Resets the MTU size for this manual session to default (1460)
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1151 no l2tpv3-manual-session-commands Negates or reverts L2TPV3 manual session settings to default values Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax no [local-cookie|local-ip-address|local-session-id|mtu|peer|remote-cookie| remote-session-id|traffic-source] Parameters no [local-cookie|local-ip-address|local-session-id|mtu|peer|remote-cookie| remote-session-id|traffic-source] no local-cookie Removes the local cookie size configured for a manual session no local-ip-address Resets the manual sessions local source IP address and reestablishes the tunnel no local-session-id Removes the manual sessions local session ID no mtu Resets the mtu size for this manual sessions to default (1460) no peer Removes the peer configuration from this tunnel no remote-cookie Removes the remote cookie field size no remote-session-id Removes the manual sessions remote session ID no traffic-source Removes the configured traffic source
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1152 Example The tunnel settings before the no command is executed: wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-ip-address 1.2.3.4 peer ip-address 5.6.7.8 udp port 150 traffic-source vlan 50-60 native-vlan 2 local-session-id 1 remote-session-id 200 remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# The tunnel settings after the no command is executed: wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#no local-ip-address wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#no local-session-id wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#no remote-session-id wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 peer ip-address 5.6.7.8 udp port 150 traffic-source vlan 50-60 native-vlan 2 remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands local-cookie Configures the local cookie field size for the manual session local-ip-address Configures the manual sessions local source IP address local-session-id Removes the manual sessions local session ID mtu Configures the manual sessions mtu size peer Configures the manual sessions peers remote-cookie Configures the manual sessions remote cookie field size remote-session-id Configures the manual sessions remote session ID
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1153 traffic-source Configures the traffic source that will be tunneled by this tunnel
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1154 peer l2tpv3-manual-session-commands Configures peer(s) allowed to establish the manual session tunnel. The peers are identified by their IP addresses. Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax peer ip-address <A.B.C.D> {udp port <1-65535>} Parameters peer ip-address <A.B.C.D> {udp port <1-65535>} Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#peer ip-address 5.6.7.8 udp port 150 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-cookie size 8 200 300 local-ip-address 1.2.3.4 peer ip-address 5.6.7.8 udp port 150 mtu 200 local-session-id 1 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands peer ip-address <A.B.C.D> Configures the tunnels peer IP address in the A.B.C.D format udp port <1-65335> The UDP option configures the encapsulation mode for this tunnel. UDP Optional. Configures UDP encapsulation (default encapsulation is IP) port <1-65535> Configures the peers UDP port running the L2TPV3 service. from 1 - 65535. no Removes the manual sessions peer
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1155 remote-cookie l2tpv3-manual-session-commands Configures the manual sessions remote cookie field size Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax remote-cookie size [4|8] <1-4294967295> {<1-4294967295>} Parameters remote-cookie size [4|8] <1-4294967295> {<1-4294967295>} Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-ip-address 1.2.3.4 peer ip-address 5.6.7.8 udp port 150 mtu 200 local-session-id 1 remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# remote-cookie size [4|8] Configures the remote cookie field size for this manual session. The options are: 4 4 byte remote cookie field 8 8 byte remote cookie field <1-4294967295> Configures the remote cookie value firstword. Applies to both the 4 byte and 8 byte local cookies <1-4294967295> Optional Configures the remote cookie value secondword. Applicable to only 8 byte cookies. This parameter is ignored for 4 byte cookies.
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1156 Related Commands no Removes the manual sessions remote cookie field size
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1157 remote-session-id l2tpv3-manual-session-commands Configures the manual sessions remote session ID Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax remote-session-id <1-4294967295> Parameters remote-session-id <1-4294967295> Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#remote-session-id 200 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-ip-address 1.2.3.4 peer ip-address 5.6.7.8 udp port 150 local-session-id 1 remote-session-id 200 remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# Related Commands remote-session-id <1-4294967295> Configures this manual sessions remote session ID from 1 - 4294967295 no Removes the manual sessions remote session ID
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1158 traffic-source l2tpv3-manual-session-commands Configures the traffic source that will be tunneled by this tunnel Supported in the following platforms: AP4532 AP4731 WM3400 WM3600 WM3700 Syntax traffic-source vlan <VLAN-ID-RANGE> {native-vlan <1-4094>} Parameters traffic-source vlan <VLAN-ID-RANGE> {native-vlan <1-4094>} Example wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#traffic-source vlan 50-60 native-vlan 2 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)#show context l2tpv3 manual-session manualSession1 local-ip-address 1.2.3.4 peer ip-address 5.6.7.8 udp port 150 traffic-source vlan 50-60 native-vlan 2 local-session-id 1 remote-session-id 200 remote-cookie size 8 400 700 wm3400-34710C8(config-profile default-wm3400-l2tpv3-manual-session-manualSessio n1)# traffic-source vlan <VLAN-ID-RANGE> Configures VLAN as the traffic source for this tunnel <VLAN-ID-RANGE> Configures VLAN range list of traffic source. Specify the VLAN IDs as a range (for example, 10-20, 25, 30-35) native-vlan <1-4094> Optional Configures the native VLAN ID for this session, which is not tagged <1-4094> Specify the native VLAN ID between 1- 4094.
l2tpv3-manual-session-commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1159 Related Commands no Removes the traffic source configured for a tunnel
Chapter 26: L2TPV3-Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1160
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1161 C H A P T E R 27 Router-Mode Commands his chapter summarizes router-mode commands in detail. All the router-mode commands are available on both device and profile modes. Use the (config) instance to configure router commands. To navigate to the (config-router-mode) instance, use the following commands: wm3400-34710C8(config-profile-default-wm3400)#router ospf wm3400-34710C8(config-profile default-wm3400-router-ospf)#? Router OSPF Mode commands: area OSPF area auto-cost OSPF auto-cost default-information Distribution of default information ip Internet Protocol (IP) network OSPF network no Negate a command or set its defaults ospf Ospf passive Make OSPF Interface as passive redistribute Route types redistributed by OSPF route-limit Limit for number of routes handled OSPF process router-id Router ID vrrp-state-check Publish interface via OSPF only if the interface VRRP state is not BACKUP clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-router-ospf)#
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1162 router-mode The following table Plej;jsummarizes router-mode commands in detail Command Description Reference area Specifies OSPF enabled interfaces page 27-1163 auto-cost Specifies the reference bandwidth in terms of Mbits per second page 27-1165 default-information Controls the distribution of default information page 27-1166 ip Configures Internet Protocol (IP) settings page 27-1167 network Defines OSPF network settings page 27-1168 ospf Enables OSPF settings page 27-1169 passive Specifies the configured OSPF interface as passive interface page 27-1170 redistribute Specifies the route types redistributed by OSPF page 27-1171 route-limit Specifies the limit for the number of routes handled by OSPF process page 27-1172 router-id Specifies the router ID for OSPF process page 27-1174 vrrp-state-check Publishes interface via OSPF based on VVRP status page 27-1175 no Negates a command or sets its defaults page 27-1176
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1163 area router-mode Specifies OSPF enabled interfaces Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax area [<0-4294967295>|<A.B.C.D>] Parameters area [<0-4294967295>|<A.B.C.D>] Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#area 4 ? wm3400-34710C8(config-profile default-wm3400-router-ospf-area wm3400-34710C8(config-profile default-wm3400-router-ospf)#area 4 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.4)#? Router OSPF Area Mode commands: area-type OSPF area type authentication Authentication scheme for OSPF area no Negate a command or set its defaults range Routes matching this range are considered for summarization (ABR only) clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.4)# <0-4294967295> Defines OSPF area in the form of an integer. Specify the value from 0 - 4294967295. <A.B.C.D> Defines OSPF area in the form of IP address. Specify the IP address.
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1164 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.4)#show context area 0.0.0.4 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.4)#
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1165 auto-cost router-mode Specifies the reference bandwidth in terms of Mbits per second Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax auto-cost reference-bandwidth <1-4294967> Parameters auto-cost reference-bandwidth <1-4294967> Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#auto-cost reference- bandwidth 1 Please make sure that auto-cost reference-bandwidth is configured uniformly on all routers wm3400-34710C8(config-profile default-wm3400-router-ospf)# reference-bandwidth Defines the reference bandwidth in Mbps <1-4294967> Specify the reference bandwidth value from1 - 4294967.
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1166 default-information router-mode Controls the distribution of default route information Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax default-information originate {always|metric <0-16777214>|metric-type[1|2]} default-information originate always {metric <0-16777214>|metric-type[1|2]} default-information originate metric <0-16777214> {metric-type}[1|2] default-information originate metric-type [1|2] {metric} <0-16777214> Parameters default-information originate {always|metric <0-16777214>|metric-type[1|2]} Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#default-information originate metric-type 2 metric 1 wm3400-34710C8(config-profile default-wm3400-router-ospf)# originate Originates default route information always Always distributes default route information metric <0-16777214> Specifies OSPF metric value for redistributed routes. Specify a value from 0 - 16777214. metric-type [1|2] Sets OSPF exterior metric type for redistributed routes 1 Sets OSPF external type 1 metrics 2 Sets OSPF external type 2 metrics
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1167 ip router-mode Configures Internet Protocol (IP) settings Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ip default-gateway priority <1-8000> Parameters ip default-gateway priority <1-8000> Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#ip default-gateway priority 1 wm3400-34710C8(config-profile default-wm3400-router-ospf)# default-gateway Configures the default gateway value priority <1-8000> Sets the priority value for the default gateway acquired via OSPF. Specify an integer value from 1 - 8000.
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1168 network router-mode Specifies the networks on which OSPF is configured Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax network <A.B.C.D/M> area [<0-4294967295>|<A.B.C.D>] Parameters network <A.B.C.D/M> area [<0-4294967295>|<A.B.C.D>] Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#network 1.2.3.4/5 area 4.5.6.7 wm3400-34710C8(config-profile default-wm3400-router-ospf)# < A.B.C.D/M> Specifies OSPF network address/mask value area <0-4294967295> Defines OSPF area in the form of an integer. Specify the value from 0 - 4294967295. <A.B.C.D> Defines OSPF area in the form of IP address. Specify the IP address.
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1169 ospf router-mode Enables OSPF settings Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax ospf enable Parameters ospf enable Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#ospf enable wm3400-34710C8(config-profile default-wm3400-router-ospf)# ospf enable Enables OSPF settings
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1170 passive router-mode Specifies the configured OSPF interface as passive interface Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax passive [<WORD>|all|vlan <1-4094>] Parameters passive [<WORD>|all|vlan <1-4094>] Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#passive vlan 1 wm3400-34710C8(config-profile default-wm3400-router-ospf)# <WORD> Specify the name of the interface all Enables OSPF passive mode on all the L3 interfaces vlan <1-4094> Specify the VLAN value from 1 - 4094.
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1171 redistribute router-mode Specifies the route types redistributed by OSPF Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax redistribute [connected|kernel|static] {metric <0-16777214>|metric-type[1|2]} Parameters redistribute [connected|kernel|static] {metric <0-16777214>|metric-type[1|2]} Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#redistribute static metric-type 1 wm3400-34710C8(config-profile default-wm3400-router-ospf)# connected Redistributes all the connected interface routes by OSPF kernel Redistributes all the routes that are neither connected, nor static, nor dynamic. static Redistributes the static routes by OSPF metric <0-16777214> Specifies OSPF metric value for redistributed routes. Specify a value from 0 - 16777214. metric-type[1|2] Sets OSPF exterior metric type for redistributed routes 1 Sets OSPF external type 1 metrics 2 Sets OSPF external type 2 metrics
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1172 route-limit router-mode Specifies the limit for the number of routes handled by OSPF process. The maximum limit supported by the platform is the default configuration defined under the router-ospf context Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax route-limit {num-routes <DYNAMIC-ROUTE-LIMIT>|reset-time <1-86400>| retry-count <1-32>|retry-timeout <1-3600>} Parameters route-limit {num-routes <DYNAMIC-ROUTE-LIMIT>|reset-time <1-86400>| retry-count <1-32>|retry-timeout <1-3600>} Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#route-limit reset-time 10 wm3400-34710C8(config-profile default-wm3400-router-ospf)# wm3400-34710C8(config-profile default-wm3400-router-ospf)#show context include- factory router ospf ospf enable no router-id no auto-cost reference-bandwidth no default-information originate num-routes <DYNAMIC-ROUTE-LIMIT> Specifies the maximum number of non self-generated LSAs this process can receive. <DYNAMIC-ROUTE-LIMIT> Specify the dynamic route limit. reset-time <1-86400> Specifies the time in seconds after which the retry-count is reset to zero. Specify a value from 1 - 86400 seconds. retry-count <1-32> Specifies the maximum number of times, the adjacencies can be suppressed. Each time the OSPF process gets into an ignore state, a counter is incremented. If the counter exceeds the timeout configured by the retry-count, then the OSPF process stays permanently in the same ignore state. Then manual intervention is required to get the OSPF process out of the ignore state. retry-timeout <1-3600> Specifies the time in seconds. During this time, the OSPF process remains in ignore state and all the adjacencies are suppressed. Specify a value from 1 - 3600 seconds.
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1173 no passive all vrrp-state-check route-limit num-routes 10 retry-count 5 retry-timeout 60 reset-time 10 ip default-gateway priority 7000 wm3400-34710C8(config-profile default-wm3400-router-ospf)#
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1174 router-id router-mode Specifies the router ID for OSPF process Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax router-id <A.B.C.D> Parameters router-id <A.B.C.D> Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#router-id 172.16.10.8 Reload, or execute "clear ip ospf process" command, for this to take effect wm3400-34710C8(config-profile default-wm3400-router-ospf)# <A.B.C.D> Specify the IP address for the router ID.
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1175 vrrp-state-check router-mode Publishes interface via OSPF based on VVRP status Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax vrrp-state-check Parameters vrrp-state-check Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#vrrp-state-check Disable and enable OSPF feature for this command to take effect wm3400-34710C8(config-profile default-wm3400-router-ospf)# wm3400-34710C8(config-profile default-wm3400-router-ospf)#show context include- factory router ospf ospf enable no router-id no auto-cost reference-bandwidth no default-information originate no passive all vrrp-state-check route-limit num-routes 10 retry-count 5 retry-timeout 60 reset-time 10 ip default-gateway priority 7000 wm3400-34710C8(config-profile default-wm3400-router-ospf)# vrrp-state-check Publishes interface via OSPF based on VRRP status
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1176 no router-mode Negates a command or set its defaults Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [area|auto-cost|default-information|ip|network|ospf|passive|redistribute|route- limit|router-id| vrrp-state-check] Parameters [area|auto-cost|default-information|ip|network|ospf|passive|redistribute|route- limit|router-id| vrrp-state-check] Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#no area 1 wm3400-34710C8(config-profile default-wm3400-router-ospf)# no Negates a command or set its defaults
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1177 OSPF-area-mode router-mode Use the (config) instance to configure ospf-area commands. To navigate to the (config-router-ospf-area- mode) instance, use the following commands: wm3400-34710C8(config-profile default-wm3400-router-ospf)#area 1 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)#? Router OSPF Area Mode commands: area-type OSPF area type authentication Authentication scheme for OSPF area no Negate a command or set its defaults range Routes matching this range are considered for summarization (ABR only) clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)# The following table summarizes OSPF area mode commands in detail Command Description Reference area-type Configures a particular OSPF area as STUB or NSSA page 27-1178 authentication Specifies the authentication scheme to be used for the OSPF area page 27-1179 range Specifies the routes matching address/mask for summarization page 27-1180 no Negates a command or sets its defaults page 27-1181
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1178 area-type OSPF-area-mode Configures a particular OSPF area as STUB, Totally STUB, NSSA or Totally NSSA Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax area-type [nssa|stub] area-type nssa {default-cost <0-16777215> {no-summary}|no-summary default-cost <0-16777215>|translate-always|translate-candidate|translate-never} area-type nssa [translate-always|translate-candidate|translate-never] {default-cost <0-16777215>|no-summary} area-type stub {default-cost <0-16777215> {no-summary}|no-summary default-cost <0-16777215>} Parameters area-type [nssa|stub] Example wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)#area-type stub default-cost 1 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)# nssa Configures the OSPF area as Not So Stubby Area (NSSA) stub Configures the OSPF area as Stubby Area (STUB) default-cost <0-16777215> Specifies the default summary cost that will be advertised, if the OSPF area is a STUB or NSSA <0-16777215> Specify the default summary cost value from 0 - 16777215. no-summary Configures the OSPF area as totally STUB if the area-type is STUB or totally NSSA if the area-type is NSSA translate-always Always translate type-7 LSAs into type 5 LSAs translate-candidate Defines it as default behavior translate-never Never translate type-7 LSAs into type 5 LSAs
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1179 authentication OSPF-area-mode Specifies the authentication scheme to be used for the OSPF area Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication [message-digest|simple-password] Parameters authentication [message-digest|simple-password] Example wm3400-34710C8(config-profile default-wm3400-router-ospf-area- 0.0.0.1)#authentication simple-password wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)# message-digest Defines authentication scheme as message-digest simple-password Defines simple password as authentication scheme
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1180 range OSPF-area-mode Specifies the routes matching address/mask for summarization Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax range <A.B.C.D/M> Parameters range <A.B.C.D/M> Example wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)#range 172.16.10.1/24 wm3400-34710C8(config-profile default-wm3400-router-ospf-area-0.0.0.1)# <A.B.C.D/M> Specifies the routes matching address/mask for summarization. NOTE This command is applicable for ABR only.
router-mode Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1181 no router-mode Negates a command or set its defaults Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [area-type|authentication|range] Parameters no [area-type|authentication|range] Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-profile default-wm3400-router-ospf)#no area-type wm3400-34710C8(config-profile default-wm3400-router-ospf)# no Negates a command or set its defaults
Chapter 27: Router-Mode Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1182
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1183 C H A P T E R 28 Routing-Policy Commands This chapter summarizes routing-policy commands in detail. Use the (config) instance to configure router-policy commands. To navigate to the (config-routing-policy mode) instance, use the following commands: wm3400-34710C8(config)#routing-policy testpolicy wm3400-34710C8(config-routing-policy-testpolicy)#? Routing Policy Mode commands: apply-to-local-packets Use Policy Based Routing for packets generated by the device logging Enable logging for this Route Map no Negate a command or set its defaults route-map Create a Route Map use Set setting to use clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-routing-policy-testpolicy)#
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1184 routing-policy Commands The following table summarizes routing-policy commands in detail Command Description Reference apply-to-local-packets Enables/Disables policy based routing for locally generated packets page 28-1185 logging Enables logging for a specified route map page 28-1186 route-map Creates a route map entry page 28-1187 use Defines default settings to use page 28-1196 no Negates a command or sets its defaults page 28-1197
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1185 apply-to-local-packets routing-policy Commands Enables/Disables policy based routing for locally generated packets Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax apply-to-local-packets Parameters None Example wm3400-34710C8(config-routing-policy-testpolicy)#apply-to-local-packets wm3400-34710C8(config-routing-policy-testpolicy)#
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1186 logging routing-policy Commands Enables logging for a specified route map Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax logging Parameters None Example wm3400-34710C8(config-routing-policy-testpolicy)#logging wm3400-34710C8(config-routing-policy-testpolicy)#
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1187 route-map routing-policy Commands Creates a route map entry and changes the mode to route-map mode for further configuration Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax route-map <1-100> Parameters route-map <1-100> Example wm3400-34710C8(config-routing-policy-testpolicy)#route-map 1 wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#? Route Map Mode commands: default-next-hop Default next-hop configuration (aka gateway-of-last-resort) fallback Fallback to destination based routing if no next-hop is configured or all are unreachable mark Mark action for route map match Match clause configuration for Route Map next-hop Next-hop configuration no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)# route-map <1-100> Creates a route map entry and changes the mode to route-map mode for further configuration. Specify a precedence value from 1-100.
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1188 route-map-mode routing-policy Commands The following table summarizes route-map-mode commands in detail Command Description Reference default-next-hop Sets the next-hop for packets that satisfy the specified match criteria page 28-1189 fallback Configures fallback to the next destination page 28-1190 mark Marks action for the route map page 28-1191 match Sets match clause configuration for a specified route map page 28-1192 next-hop Sets the next-hop for packets that satisfy the specified match criteria page 28-1194 no Negates a command or sets its default page 28-1195
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1189 default-next-hop route-map-mode Sets the next-hop for packets that satisfy the specified match criteria Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax default-next-hop [<A.B.C.D>|<WORD>|pppoe1|vlan<1-4094>|wwan1] Parameters default-next-hop [<A.B.C.D>|<WORD>|pppoe1|vlan<1-4094>|wwan1] Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#default-next-hop ww an1 wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)# default-next--hop Sets the next-hop for packets that satisfy the specified match criteria <A.B.C.D> Specify the IP address of the next hop. <WORD> Specify the outgoing interface name. pppoe1 Specifies PPoE interface vlan <1-4094> Specifies a switch VLAN interface. Specify a VLAN ID from 1 - 4094. wwan1 Specifies Wireless WAN interface
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1190 fallback route-map-mode Configures fallback to the next destination. If none of the configured outgoing interfaces and next-hops are up, then fallback to the normal destination is configured. If fallback is not configured, the default behavior is to drop the packet. Supported in the following platforms: AP4532 AP4700 WM3400 WM3600 WM3700 Syntax fallback Parameters None Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#fallback wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1191 mark route-map-mode Marks action for the route map Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax mark ip dscp <0-63> Parameters mark ip dscp <0-63> Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#mark ip dscp 7 wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)# ip dscp <0-63> Marks the DSCP field in IP header. Specify a DSCP value from 0 - 63.
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1192 match route-map-mode Sets match clause configuration for a specified route map Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax match [incoming-interface|ip|ip-access-list|wireless-client-role|wlan] match incoming-interface [<WORD>|pppoe1|vlan <1-4094>|wwan1] match ip dscp <0-63> match ip-access-list <IP-ACCESS-LIST> match wireless-client-role <ROLE-POLICY> <ROLE> match wlan <WLAN> Parameters incoming-interface [<WORD>|pppoe1|vlan <1-4094>|wwan1] ip dscp <0-63> ip-access-list <IP-ACCESS-LIST> wireless-client-role <ROLE-POLICY> <ROLE> wlan <WLAN> incoming-interface Sets the incoming SVI match clause. Specify an interface name. <WORD> Specifies layer 3 interface name pppoe1 Specifies PPP over Ethernet interface vlan <1-4094> Specifies Switch VLAN interface name. Specify a VLAN ID from 1 - 4094. wwan1 Specifies Wireless WAN interface name ip dscp <0-63> Sets the DSCP match clause. Specify a DS code point value from 0 - 63. ip-access-list <IP-ACCESS-LIST> Sets the match clause using a preconfigured IP Access List. Specify a preconfigured IP access list name. wireless-client-role <ROLE-POLICY> <ROLE> Sets the wireless client role match clause. Specify a preconfigured role policy and a preconfigured role within it. wlan <WLAN> Sets the incoming WLAN match clause. Specify a WLAN name.
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1193 Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#match incoming-inte rface pppoe1 wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1194 next-hop route-map-mode Sets the next-hop for packets that satisfies the specified match criteria Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax next-hop [A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwlan1] {A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwlan1} Parameters next-hop [A.B.C.D>|<WORD>|pppoe1|vlan <1-4094>|wwlan1] {A.B.C.D>|<WORD>| pppoe1|vlan <1-4094>|wwlan1} Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#next-hop vlan 1 wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)# next-hop Sets the next-hop for packets that satisfy the match criteria [A.B.C.D] Specifies the IP addresses of primary and secondary next-hop <WORD> Specifies layer 3 Interface name (router interface) pppoe1 Specifies PPP over Ethernet interface vlan <1-4094> Specifies switch VLAN interface. Specify a VLAN ID from 1 - 4094. The VLAN interface should be a DHCP client. wwan1 Specifies Wireless WAN interface
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1195 no route-map-mode Negates a command or sets its defaults Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax no [default-next-hop|fallback|mark|match|next-hop] Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#no default-next-hop wm3400-34710C8(config-routing-policy-testpolicy-route-map-1)#
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1196 use routing-policy Commands Uses Critical Resource Monitoring to monitor the status of a link Supported in the following platforms: WM3400 WM3600 WM3700 Syntax use critical-resource-monitoring Parameters use critical-resource-monitoring Example wm3400-34710C8(config-routing-policy-testpolicy)#use critical-resource-monitoring wm3400-34710C8(config-routing-policy-testpolicy)# use critical-resource-monitoring Uses Critical Resource Monitoring to monitor the status of a link. This determines the status of next-hop in Route Map, via which the critical resources are being monitored. Link monitoring is used for failover to a secondary next-hop
routing-policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1197 no route-map-mode Negates a command or sets its defaults Supported in the following platforms: AP4700 WM3400 WM3600 WM3700 Syntax no [apply-to-local-packets|logging|route-map|use]] Parameters None Usage Guidelines The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated. Example wm3400-34710C8(config-routing-policy-testpolicy)#no logging wm3400-34710C8(config-routing-policy-testpolicy)#
Chapter 28: Routing-Policy Commands Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1198
Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1199 C H A P T E R 29 AAA-TACACS Policy This chapter summarizes the Terminal Access Control Access-Control System (TACACS) policy commands within the CLI structure. Use the (config) instance to configure AAA-TACACS policy commands. To navigate to the config-aaa- tacacs-policy instance, use the following commands: wm3400-34710C8(config)#aaa-tacacs-policy <POLICY-NAME> wm3400-34710C8(config)#aaa-tacacs-policy test wm3400-34710C8(config-aaa-tacacs-policy-test)#? AAA TACACS Policy Mode commands: accounting Configure accounting parameters authentication Configure authentication parameters authorization Configure authorization parameters no Negate a command or set its defaults clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal wm3400-34710C8(config-aaa-tacacs-policy-test)#
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1200 aaa-tacacs-policy The following table summarizes AAA-TACACS policy commands Command Description Reference accounting Configures accounting parameters page 29-1201 authentication Configures authentication parameters page 29-1204 authorization Configures authorization parameters page 29-1206 no Negates a command or sets its default page 29-1209 clrscr Clears the display screen page 6-379 commit Commits (saves) changes made in the current session page 6-380 do Runs commands from EXEC mode page 5-241 end Ends and exits the current mode and moves to the PRIV EXEC mode page 6-381 exit Ends the current mode and moves to the previous mode page 6-382 help Displays the interactive help system page 6-383 revert Reverts changes to their last saved configuration page 6-390 service Invokes service commands to troubleshoot or debug ( conf i g- i f ) instance configurations page 6-391 show Displays running system information page 7-425 write Writes information to memory or terminal page 6-420
aaa-tacacs-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1201 accounting aaa-tacacs-policy Configures the server type and interval at which interim accounting updates are sent to the server. Up to 2 accounting servers can be configured. Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax accounting [auth-fail|command|server|session] accounting server [<1-2>|preference] accounting server preference [authenticated-server-host|authenticated-server-number| authorized-server-host|authorized-server-number|none] accounting server <1-2> [host|retry-timeout-factor <50-200>|timeout] accounting server <1-2> host <HOSTNAME> secret [0 <SECRET>|2 <SECRET>|<SECRET>] {port <1-65535>} accounting server <1-2> timeout <3-5> {attempts <1-3>} Parameters accounting [auth-fail|command|session] accounting server preference [authenticated-server-host|authenticated-server- number|authorized-server-host|authorized-server-number|none] auth-fail Enables Accounting for Authentication fail details commands Enables Accounting for commands session Enables Accounting for Session start and stop details server Configures an accounting server preference Configures the accounting server preference authenticated-server-host Sets the authentication server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its hostname. authenticated-server-number Sets the authentication server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its index or number.
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1202 accounting server <1-2> [retry-timeout-factor <50-200>] accounting server <1-2> host <HOSTNAME> secret [0 <SECRET>|2 <SECRET>|<SECRET>] {port <1-65535>} accounting server <1-2> timeout <3-5> {attempts <1-3>} Example wm3400-34710C8(config-aaa-tacacs-policy-test)#accounting auth-fail wm3400-34710C8(config-aaa-tacacs-policy-test)# wm3400-34710C8(config-aaa-tacacs-policy-test)#accounting commands authorized-server-host Sets the authentication server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its hostname. authorized-server-number Sets the authorized server as the accounting server This parameter indicates the same server is used for authentication and accounting. The server is referred to by its index or number. none Indicates the accounting server is independent of the authentication server server <1-2> Configures an accounting server. Up to 2 accounting servers can be configured retry-timeout-factor <50-200> Sets the scaling factor for retry timeouts <50-200> Specify a value from 50 - 200. A value of 100 indicates the interval between 2 consecutive retries is the same irrespective of the number of retries. If the scaling factor value is less than 100, the time interval between two consecutive retires keeps reducing on subsequent retries. If this value is greater than 100, the time interval between two consecutive retries keeps increasing on subsequent retries. server <1-2> Configures an accounting server. Up to 2 accounting servers can be configured host <HOSTNAME> Configures the accounting server hostname secret [0 <SECRET>| 2 <SECRET>|<SECRET>] Configures a common secret key used to authenticate with the accounting server 0 <SECRET> Configures a clear text secret key 2 <SECRET> Configures an encrypted secret key <SECRET> Specify the secret key. This shared secret should not exceed 127 characters. port <1-65535> Optional. Configures the accounting server port (the port used to connect to the accounting server) <1-65535> Sets the port number from 1 - 65535 server <1-2> Configures an accounting server. Up to 2 accounting servers can be configured timeout <3-5> Configures the timeout for each request sent to the RADIUS server <3-5> Specify a value from 3 - 5 seconds. {attempts<1-3>} Optional. Specified the number of times a transmission request is attempted <1-3> Specify a value from 1 - 3.
aaa-tacacs-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1203 wm3400-34710C8(config-aaa-tacacs-policy-test)# wm3400-34710C8(config-aaa-tacacs-policy-test)#accounting server preference none wm3400-34710C8(config-aaa-tacacs-policy-test)# wm3400-34710C8(config-aaa-tacacs-policy-test)#accounting server preference authenticated-server-host wm3400-34710C8(config-aaa-tacacs-policy-test)# wm3400-34710C8(config-aaa-tacacs-policy-test)#accounting server preference authorized-server-number wm3400-34710C8(config-aaa-tacacs-policy-test)# Related Commands no Resets values or disables commands
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1204 authentication aaa-tacacs-policy Configures authentication parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authentication [directed-request|server] authentication server <1-2> [host|retry-timeout-factor|timeout] authentication server <1-2> host <IP/HOSTNAME> secret [0 <SECRET>|2 <SECRET>| <SECRET>] {port <1-65535>} authentication server <1-2> retry-timeout-factor <50-200> authentication server <1-2> timeout <3-60> {attempts <1-10>} Parameters authentication directed-request authentication server <1-2> host <IP/HOSTNAME> secret [0 <SECRET>|2 <SECRET>| <SECRET>] {port <1-65535>} directed-request Enables user to specify TACACS server to use with `@server'. Server specified should be present in configured list of servers server <1-2> Configures a RADIUS authentication server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1 - 2. host <IP/HOSTNAME> Sets the RADIUS servers IP address or hostname secret [0 <SECRET>| 2 <SECRET>|<SECRET>] Configures the RADIUS server secret. This key is used to authenticate with the RADIUS server 0 <SECRET> Configures a clear text secret 2 <SECRET> Configures an encrypted secret <SECRET> Specify the secret key. The shared key should not exceed 127 characters. port <1-65535> Optional. Specifies the RADIUS server port (this port is used to connect to the RADIUS server) <1-65535> Specify a value from 1 - 65535.
aaa-tacacs-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1205 authentication server <1-2> retry-timeout-factor <50-200> authentication server <1-2> timeout <3-60> {attempts <1-10>} Example wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)#authentication directed-request wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)# Related Commands server <1-2> Configures a RADIUS authentication server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1 - 2. retry-timeout-factor <50-200> Configures the scaling of timeouts between two consecutive RADIUS authentication retries <50-200> Specify the scaling factor from 50 - 200. A value of 100 indicates the time gap between two consecutive retires remains the same irrespective of the number of retries. A value lesser than 100 indicates the time gap between two consecutive retries reduces with each successive retry attempt. A value greater than 100 indicates the time gap between two consecutive retries increases with each successive retry attempt. server <1-2> Configures a RADIUS authentication server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1- 2. timeout <3-60> Configures the timeout, in seconds, for each request sent to the RADIUS server. This is the time allowed to elapse before another request is sent to the RADIUS server. If a response is received from the RADIUS server within this time, no retry is attempted. <3-60> Specify a value from 3- 60 seconds. attempts <1-10> Optional. Indicates the number of retry attempts to make before giving up <1-10> Specify a value from 1 -10. no Resets values or disables commands
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1206 authorization aaa-tacacs-policy Configures authorization parameters Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax authorization [access-method|allow-privileged-commands|server] authorization access-method [all|console|telnet|ssh] authorization access-method [console {telnet|ssh}|telnet {console|ssh}| ssh {telnet|console}] authorization server [<1-2>|preference] authorization server <1-2> [host|retry-timeout-factor|timeout] authorizationserver <1-2> host <IP/HOSTNAME> secret [0 <SECRET>|2 <SECRET>| <SECRET>] {port <1-65535>} authorization server <1-2> retry-timeout-factor <50-200> authorization server <1-2> timeout <3-5> {attempts <1-3>} authorization server preference [authenticated-server-host|authenticated-server- number|none] Parameters authorization access-method [all|console|telnet|ssh] authorization allow-privileged-commands access-method Configures access method for command authorization all Authorizes commands from all access methods console Authorizes commands from console telnet Authorizes commands from Telnet ssh Authorizes commands from SSH allow-privileged-commands Allows privileged commands execution without command authorization
aaa-tacacs-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1207 authorization server <1-2> host <IP/HOSTNAME> secret [0 <SECRET>|2 <SECRET>| <SECRET>] {port <1-65535>} authorization server <1-2> retry-timeout-factor <50-200> authorization server <1-2> timeout <3-5> {attempts <1-3>} authorization server preference [authenticated-server-host|authenticated-server- number|none] server <1-2> Configures a RADIUS authorization server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1 - 2. host <IP/HOSTNAME> Sets the RADIUS servers IP address or hostname secret [0 <SECRET>| 2 <SECRET>|<SECRET>] Configures the RADIUS server secret. This key is used to authorize with the RADIUS server 0 <SECRET> Configures a clear text secret 2 <SECRET> Configures an encrypted secret <SECRET> Specify the secret key. The shared key should not exceed 127 characters. port <1-65535> Optional. Specifies the RADIUS server port (this port is used to connect to the RADIUS server) <1-65535> Specify a value from 1 - 65535. server <1-2> Configures a RADIUS authorization server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1 - 2. retry-timeout-factor <50-200> Configures the scaling of timeouts between two consecutive RADIUS authorization retries <50-200> Specify the scaling factor from 50 - 200. A value of 100 indicates the time gap between two consecutive retires remains the same irrespective of the number of retries. A value lesser than 100 indicates the time gap between two consecutive retries reduces with each successive retry attempt. A value greater than 100 indicates the time gap between two consecutive retries increases with each successive retry attempt. server <1-2> Configures a RADIUS authorization server. Up to 2 RADIUS servers can be configured <1-2> Specify the RADIUS server index from 1- 2. timeout <3-5> Configures the timeout, in seconds, for each request sent to the RADIUS server. This is the time allowed to elapse before another request is sent to the RADIUS server. If a response is received from the RADIUS server within this time, no retry is attempted. <3-5> Specify a value from 3 - 5 seconds. attempts <1-3> Optional. Indicates the number of retry attempts to make before giving up <1-3> Specify a value from 1 - 3. preference Configures the authorization server preference
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1208 Example wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)#authorization allow-privileged- commands wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)# authenticated-server-host Sets the authentication server as the authorization server This parameter indicates the same server is used for authentication and authorization+. The server is referred to by its hostname. authenticated-server-number Sets the authentication server as the authorization server This parameter indicates the same server is used for authentication and authorization. The server is referred to by its index or number. none Indicates the authorization server is independent of the authentication
aaa-tacacs-policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1209 no aaa-tacacs-policy Negates a AAA policy command or sets its default Supported in the following platforms: AP4021 AP4600 AP4511 AP4521 AP4532 AP4700 WM3400 WM3600 WM3700 Syntax no [accounting|authentication|authorization] Parameters no accounting interim interval Example wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)#no authorization allow- privileged-commands wm3400-34710C8(config-aaa-tacacs-policy-testppolicy)# Related Commands no Negates a command or set its defaults accounting Configures RADIUS accounting parameters authentication Configures RADIUS authentication parameters authorization Configures RADIUS authorization parameters
Chapter 29: AAA-TACACS Policy Summit
WM3000 Series Controller and Altitude
TM 4000 Series Access Point CLI Reference Guide 1210
Wireless Mobility 5.4 CLI Reference Guide 1343 A P P E N D I X A Controller Managed WLAN Use Case This section describes the activities required to configure a controller managed WLAN. Instructions are provided using the controller CLI. Creating a First Controller managed WLAN Assumptions Design Using the Command Line Interface to Configure the WLAN Creating a First Controller Managed WLAN It is assumed you have a WM3400 wireless controller with the latest build available from Extreme Networks. It is also assumed you have one AP4700 model access point and one AP4600 model access point, both with the latest firmware available from Extreme Networks. Upon completion, you will have created a WLAN on a WM3400 model wireless controller using a DHCP server to allocate IP addresses to associated wireless clients. Assumptions Creating a First Controller Managed WLAN Verify the following conditions have been satisfied before attempting the WLAN configuration activities described in this section: 1 It is assumed the wireless controller has the latest firmware version available from Extreme Networks. 2 It is assumed the AP4700 and AP4600 access points also have the latest firmware version available from Extreme Networks. 3 It is assumed there are no previous configurations on the wireless controller or access point and default factory configurations are running on the devices. 4 It is assumed you have administrative access to the wireless controller and access point CLI. 5 It is assumed the individual administrating the network is a professional network installer.
Appendix A: Controller Managed WLAN Use Case Wireless Mobility 5.4 CLI Reference Guide 1344 Design Creating a First Controller Managed WLAN This section defines the network design being implemented. Figure A-1 Network Design This is a simple deployment scenario, with the access points connected directly to the wireless controller. One wireless controller port is connected to an external network. On the WM3400 wireless controller, the GE1 interface is connected to an external network. Interfaces GE3 and GE4 are used by the access points. On the external network, the controller is assigned an IP address of 192.168.10.188. The wireless controller acts as a DHCP server for the wireless clients connecting to it, and assigns IP addresses in the range of 172.16.11.11 to 172.16.11.200. The rest of IPs in the range are reserved for devices requiring static IP addresses. Using the Command Line Interface to Configure the WLAN Creating a First Controller Managed WLAN These instructions are for configuring your first WLAN using the controller CLI. Use a serial console cable when connecting to the wireless controller for the first time. Set the following configuration when using the serial connection: Bits per second: 19200 Data Bit: 8 Parity: None Stop Bit: 1 Flow Control: None
Creating a First Controller Managed WLAN Wireless Mobility 5.4 CLI Reference Guide 1345 The steps involved in creating a WLAN on a wireless controller are: 1 Logging Into the Controller for the First Time 2 Creating a RF Domain 3 Creating a Wireless Controller Profile 4 Creating an AP Profile 5 Creating a DHCP Server Policy Logging Into the Controller for the First Time Using the Command Line Interface to Configure the WLAN When powering on the wireless controller for the first time, you are prompted to replace the existing administrative password. The credentials for logging into the wireless controller for the first time are: User Name: admin Password: admin123 Ensure the new password created is strong enough to provide adequate security for the controller managed network. Creating a RF Domain Using the Command Line Interface to Configure the WLAN A RF Domain is a collection of configuration settings specific to devices located at the same physical deployment, such as a building or a floor. Create a RF Domain and assign the country code where the devices are deployed. This is a mandatory step, and the devices will not function as intended if this step is omitted. The instructions in this section must be performed from the Global Configuration mode of the wireless controller. To navigate to this mode: WM3400>enable WM3400# WM3400#configure terminal Enter configuration commands, one per line. End with CNTL/Z. WM3400(config)# Create the RF Domain using the following commands: WM3400(config)#rf-domain RFDOMAIN_UseCase1 WM3400(config-rf-domain-RFDOMAIN_UseCase1)# This command creates a profile with the name RFDOMAIN_UseCase1. Set the country code for the RF Domain. WM3400(config-rf-domain-RFDOMAIN_UseCase1)#country-code us This sets the country code for this RF Domain. Save this change and exit the RF Domain profile context. WM3400(config-rf-domain-RFDOMAIN_UseCase1)#commit write
Appendix A: Controller Managed WLAN Use Case Wireless Mobility 5.4 CLI Reference Guide 1346 WM3400(config-rf-domain-RFDOMAIN_UseCase1)#exit WM3400(config)# To define the wireless controllers physical location, use the same RF Domain configuration. WM3400(config)#self WM3400(config-device-03-14-28-57-14-28)# WM3400(config-device-03-14-28-57-14-28)#use rf-domain RFDOMAIN_UseCase1 Commit the changes and write to the running configuration. Exit this context. WM3400(config-device-03-14-28-57-14-28)#commit write WM3400(config-device-03-14-28-57-14-28)#exit WM3400(config)# Creating a Wireless Controller Profile Using the Command Line Interface to Configure the WLAN The first step in creating a WLAN is to configure a profile defining the parameters applied to a wireless controller. To create a profile: WM3400(config)#profile wm3400 wm3400_UseCase1 WM3400(config-profile-wm3400_UseCase1)# This creates a profile with the name WM3400_UseCase1 and moves the cursor into its context. Any configuration made under this profile is available when its applied to a device. Configure a VLAN Create the VLAN to use with the WLAN configuration. This can be done using the following commands: WM3400(config-profile-WM3400_UseCase1)#interface vlan 2 WM3400(config-profile-WM3400_UseCase1-if-vlan2)#ip address 172.16.11.1/24 The above command assigns the IP address 172.16.11.1 with the mask of 255.255.255.0 to VLAN2. Exit the VLAN2 context. WM3400(config-profile-WM3400_UseCase1-if-vlan2)#exit WM3400(config-profile-WM3400_UseCase1)# The next step is to assign this newly created VLAN to a physical interface. In this case, VLAN 2 is mapped to GE3 and GE4 to support two access points, an AP4600 and an AP4700. The AP4600 is connected to the gigabit interface GE3 and the AP4700 to the GE4 interface. WM3400(config-profile-WM3400_UseCase1)#interface ge 3 WM3400(config-profile-WM3400_UseCase1-if-ge3)# Map VLAN 1 to this interface. This assigns the IP address to the selected physical interface. WM3400(config-profile-WM3400_UseCase1-if-ge3)#switchport access vlan 2 WM3400(config-profile-WM3400_UseCase1-if-ge3)#exit WM3400(config-profile-WM3400_UseCase1)#
Creating a First Controller Managed WLAN Wireless Mobility 5.4 CLI Reference Guide 1347 Similarly, map the defined VLAN 1 to the GE4 interface. WM3400(config-profile-WM3400_UseCase1)#interface ge 4 WM3400(config-profile-WM3400_UseCase1-if-ge4)#switchport access vlan 2 WM3400(config-profile-WM3400_UseCase1-if-ge4)#exit WM3400(config-profile-WM3400_UseCase1)# Exit the profile and save it. WM3400(config-profile-WM3400_UseCase1)#exit WM3400(config)#commit write Configure the Wireless Controller to use the Profile Before the wireless controller can be further configured, the profile must be applied to the wireless controller. WM3400(config)#self WM3400(config-device-03-14-28-57-14-28)# WM3400(config-device-03-14-28-57-14-28)#use profile WM3400_UseCase1 WM3400(config-device-03-14-28-57-14-28)#exit WM3400(config)#commit write Create a WLAN Use the following commands to create a WLAN: WM3400(config)#wlan 1 WM3400(config-wlan-1)# Configure the SSID for the WLAN. This is the value that identifies and helps differentiate this WLAN. WM3400(config-wlan-1)#ssid WLAN_USECASE_01 Enable the SSID to be broadcast so wireless clients can find it and associate. WM3400(config-wlan-1)#broadcast-ssid Associate the VLAN to the WLAN and exit. WM3400(config-wlan-1)#vlan 2 WM3400(config-wlan-1)#exit Commit the Changes Once these changes have been made, they have to be committed before proceeding. WM3400(config)#commit write Creating an AP Profile Using the Command Line Interface to Configure the WLAN An AP profile provides a method of applying common settings to access points of the same model. The profile significantly reduces the time required to configure access points within a large deployment. For more information, see:
Appendix A: Controller Managed WLAN Use Case Wireless Mobility 5.4 CLI Reference Guide 1348 Creating an AP4600 Profile Creating an AP4700 Profile Creating an AP4600 Profile Creating an AP Profile An AP4600s firmware is updated directly by its associated wireless controller. The process is automatic, and no intervention is required. To create a profile for use with an AP4600: WM3400(config)#profile ap4600 AP4600_UseCase1 WM3400(config-profile-AP4600_UseCase1)# Assign the access point to be a member of the same VLAN defined in Creating an AP Profile on page 1347. In this section, the VLAN was defined as VLAN 2. Configure the access point to be a member of VLAN 2. WM3400(config-profile-AP4600_UseCase1)#interface vlan 2 WM3400(config-profile-AP4600_UseCase1-if-vlan2)# Configure this VLAN to use DHCP, so any device that is associated using this access point is automatically assigned a unique IP address. Once completed, exit this context. WM3400(config-profile-AP4600_UseCase1-if-vlan2)#ip address dhcp WM3400(config-profile-AP4600_UseCase1-if-vlan2)#exit The VLAN has to be mapped to a physical interface on the access point. Since the only available physical interface on the AP4600 is GE1, this VLAN is mapped to it. WM3400(config-profile-AP4600_UseCase1)#interface ge 1 WM3400(config-profile-AP4600_UseCase1-if-ge1)#switchport access vlan 2 WM3400(config-profile-AP4600_UseCase1-if-ge1)#exit Before a WLAN can be implemented, it has to be mapped to a radio on the access point. An AP4600 has 2 radios, in this scenario, both radios are utilized. WM3400(config-profile-AP4600_UseCase1)#interface radio 1 WM3400(config-profile-AP4600_UseCase1-if-radio1)#wlan 1 WM3400(config-profile-AP4600_UseCase1-if-radio1)#exit WM3400(config-profile-AP4600_UseCase1)#interface radio 2 WM3400(config-profile-AP4600_UseCase1-if-radio2)#wlan 1 WM3400(config-profile-AP4600_UseCase1-if-radio2)#exit WM3400(config-profile-AP4600_UseCase1)# Commit the changes made to this profile and exit. WM3400(config-profile-AP4600_UseCase1)#commit write WM3400(config-profile-AP4600_UseCase1)#exit WM3400(config)# Apply this Profile to the Discovered AP4600 Access the discovered access point using the following command. The discovered devices MAC address is used to access its context. WM3400(config)#ap4600 00-A0-F8-00-00-01
Creating a First Controller Managed WLAN Wireless Mobility 5.4 CLI Reference Guide 1349 WM3400(config-device-00-A0-F8-00-00-01)# Assign the AP profile to this AP4600 access point. WM3400(config-device-00-A0-F8-00-00-01)#use profile AP4600_UseCase1 WM3400(config-device-00-A0-F8-00-00-01)#commit write Apply the RF Domain profile to the AP Apply the previously created RF Domain to enable a country code to be assigned to the discovered access point. A discovered access point only works properly if its country code is the country code of its associated wireless controller. WM3400(config-device-00-A0-F8-00-00-01)#use rf-domain RFDOMAIN_UseCase1 WM3400(config-device-00-A0-F8-00-00-01)#commit write WM3400(config-device-00-A0-F8-00-00-01)#exit WM3400(config)# Creating an AP4700 Profile Creating an AP Profile To create a profile for use with an AP4700: WM3400(config)#profile ap4700 ap4700_UseCase1 WM3400(config-profile-AP4700_UseCase1)# Set the access point to be a member of the same VLAN defined in Creating an AP Profile on page 1347. In this section, the VLAN was defined as VLAN 2. Configure the access point to be a member of the VLAN 2. WM3400(config-profile-AP4700_UseCase1)#interface vlan 2 WM3400(config-profile-AP4700_UseCase1-if-vlan2)# Configure this VLAN to use DHCP, so any device associated using this access point is automatically assigned a unique IP address. Once completed, exit this context. WM3400(config-profile-AP4700_UseCase1-if-vlan2)#ip address dhcp WM3400(config-profile-AP4700_UseCase1-if-vlan2)#exit The configured VLAN has to be mapped to a physical interface on the access point. Map VLAN1 to the GE1 and GE2 interfaces on the AP4700. To configure the GE1 interface: WM3400(config-profile-AP4700_UseCase1)#interface ge 1 WM3400(config-profile-AP4700_UseCase1-if-ge1)#switchport access vlan 2 WM3400(config-profile-AP4700_UseCase1-if-ge1)#exit Similarly configure the GE2 interface. WM3400(config-profile-AP4700_UseCase1)#interface ge 2 WM3400(config-profile-AP4700_UseCase1-if-ge2)#switchport access vlan 2 WM3400(config-profile-AP4700_UseCase1-if-ge2)#exit Before the WLAN can be implemented, it has to be mapped to the physical radio on the access point. An AP4700 has 3 radios (on certain models), two of which can be configured for WLAN support. In this scenario, two radios are used.
Appendix A: Controller Managed WLAN Use Case Wireless Mobility 5.4 CLI Reference Guide 1350 WM3400(config-profile-AP4700_UseCase1)#interface radio 1 WM3400(config-profile-AP4700_UseCase1-if-radio1)#wlan 1 WM3400(config-profile-AP4700_UseCase1-if-radio1)#exit WM3400(config-profile-AP4700_UseCase1)#interface radio 2 WM3400(config-profile-AP4700_UseCase1-if-radio2)#wlan 1 WM3400(config-profile-AP4700_UseCase1-if-radio2)#exit WM3400(config-profile-AP4700_UseCase1)# Commit the changes made to the profile and exit this context. WM3400(config-profile-AP4700_UseCase1)#commit write WM3400(config-profile-AP4700_UseCase1)#exit WM3400(config)# Apply this Profile to the Discovered AP4700 Access the discovered access point using the following command. The discovered devices MAC address is used to access its context. WM3400(config)#ap4700 00-23-68-16-C6-C4 WM3400(config-device-00-23-68-16-C6-C4)# Assign the AP profile to this access point. WM3400(config-device-00-23-68-16-C6-C4)#use profile AP4700_UseCase1 WM3400(config-device-00-23-68-16-C6-C4)#commit write Apply the RF Domain profile to the AP Apply the previously created RF Domain to enable a country code to be assigned to the discovered access point. A discovered access point only works properly if its country code is the same as its associated wireless controller. WM3400(config-device-00-23-68-16-C6-C4)#use rf-domain RFDOMAIN_UseCase1 WM3400(config-device-00-23-68-16-C6-C4)#commit write WM3400(config-device-00-23-68-16-C6-C4)#Exit WM3400(config)# Creating a DHCP Server Policy Using the Command Line Interface to Configure the WLAN The DHCP server policy defines the parameters required to run a DHCP server on the wireless controller and assign IP addresses automatically to devices that associate. Configuring DHCP enables the reuse of a limited set of IP addresses. To create a DHCP server policy: WM3400(config)#dhcp-server-policy DHCP_POLICY_UseCase1 WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1)# The following table displays how IP addresses are used. IP Range Usage 172.16.11.1 till 172.16.11.10 Reserved for devices that require a static IP address
Creating a First Controller Managed WLAN Wireless Mobility 5.4 CLI Reference Guide 1351 In the table, the IP address range of 172.16.11.11 to 172.16.11.200 is available using the DHCP server. To configure the DHCP server: WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1)#dhcp-pool DHCP_POOL_USECASE1_01 WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1-pool-DHCP_POOL_USECAS E1_01)# Configure the address range as follows: WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1-pool-DHCP_POOL_USECAS E1_01)#address range 172.16.11.11 172.16.11.200 WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1-pool-DHCP_POOL_USECAS E1_01)# Configure the IP pool used with a network segment. This starts the DHCP server on the specified interface. WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1-pool-DHCP_POOL_USECAS E1_01)#network 172.16.11.0/24 WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1-pool-DHCP_POOL_USECAS E1_01)#exit WM3400-37FABE(config-dhcp-policy-DHCP_POLICY_UseCase1)#exit WM3400-37FABE(config)#commit write Configure the WM3400 to use the DHCP Policy For the DHCP to work properly, the new DHCP Server Policy must be applied to the wireless controller. To apply the DHCP Server Policy to the wireless controller: WM3400-37FABE(config)#self WM3400-37FABE(config-device-03-14-28-57-14-28)#use dhcp-server-policy DHCP_POLICY_UseCase1 WM3400-37FABE(config-device-03-14-28-57-14-28)#commit write WM3400-37FABE(config-device-03-14-28-57-14-28)#exit WM3400-37FABE(config)# Completing and Testing the Configuration Using the Command Line Interface to Configure the WLAN A wireless client must be configured to associate with the controller managed WLAN. The following information must be defined: SSID: WLAN_USECASE_01 Country: Same as the country configured in Creating a RF Domain on page 1345. In this scenario, the country code is set to US. 172.16.11.11 till 172.16.11.200 Range of IP addresses that can be assigned using the DHCP server. 172.16.11.201 till 172.16.11.254 Reserved for devices that require a static IP address IP Range Usage
Appendix A: Controller Managed WLAN Use Case Wireless Mobility 5.4 CLI Reference Guide 1352 Mode: Infrastructure With the WLAN set to beacon, use the wireless clients discovery client to discover the configured WLAN and associate.
Wireless Mobility 5.4 CLI Reference Guide 1353 A P P E N D I X B Customer Support NOTE Services can be purchased from Extreme Networks or through one of its channel partners. If you are an end-user who has purchased service through an Extreme Networks channel partner, please contact your partner first for support. Extreme Networks Technical Assistance Centers (TAC) provide 24x7x365 worldwide coverage. These centers are the focal point of contact for post-sales technical and network-related questions or issues. TAC will create a Service Request (SR) number and manage all aspects of the SR until it is resolved. For a complete guide to customer support, see the Technical Assistance Center User Guide at: www.extremenetworks.com/go/TACUserGuide The Extreme Networks eSupport website provides the latest information on Extreme Networks products, including the latest Release Notes, troubleshooting, downloadable updates or patches as appropriate, and other useful information and resources. Directions for contacting the Extreme Networks Technical Assistance Centers are also available from the eSupport website at: https://esupport.extremenetworks.com Registration If you have not already registered with Extreme Networks using a registration card supplied with your product, you can register on the Extreme Networks website at: http://www.extremenetworks.com/go/productregistration. Documentation Check for the latest versions of documentation on the Extreme Networks documentation website at: http://www.extremenetworks.com/go/documentation
Federal Criminal Indictment - US v. Judge Joseph Boeckmann - Wire Fraud, Honest Services Fraud, Travel Act, Witness Tampering - US District Court Eastern District of Arkansas
California Judicial Branch News Service - Investigative Reporting Source Material & Story Ideas