Professional Documents
Culture Documents
Astm D2563-94
Astm D2563-94
e1
Standard Practice for
Classifying Visual Defects in Glass-Reinforced Plastic
Laminate Parts
1
This standard is issued under the xed designation D 2563; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
e
1
NOTEEditorially revised 1.2 in March 2002.
1. Scope
1.1 This practice covers acceptance criteria for visual in-
spection of parts made from glass-reinforced plastic laminates.
1.2 This practice presents word descriptions of possible
defects to serve as a guide for contracts, drawings, product
specications, and nal inspection.
1.3 This practice also categorizes different inspection re-
quirements for levels of product quality.
1.4 The allowable size and frequency of permitted defects
within the acceptance level categories of this specication are
general and not related to specic service requirements. A
Level IV of allowable defects which denes allowable size,
frequency, and permitted repair procedures should be estab-
lished for specic service requirements as agreed upon be-
tween the purchaser and the supplier.
1.5 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
only.
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
NOTE 1There is no known ISO equivalent to this practice.
2. Acceptance Criteria
2.1 The method and frequency of sampling and the allow-
able defects may be previously agreed upon between the
purchaser and the seller.
2.2 Dimensions and TolerancesParts shall be inspected
for conformance with dimensions and tolerances specied on
the drawings. Any dimensions falling outside the specied
limits shall be cause for rejection.
2.3 InsertsAll inserts, nuts, studs, and lugs shall not be
damaged in any way, nor coated with laminate materials in
such a way as to impair function or mechanical t. Threads in
molded-in inserts shall be clean, smooth, free of nicks, tears, or
other damage. There shall be no laminate materials or ash on
the threads. If necessary, threaded inserts may be retapped to
clean them or remove ash. Threads containing locking fea-
tures or coated for corrosion resistance shall not be retapped.
2.4 Molded-In Threads or Cored Holes Molded-in
threads or cored holes shall be free of visible defects such as
chips, cracks, shorts, etc. Molded-in threads may be retapped
or repaired unless otherwise specically noted on the product
drawings.
2.5 WorkmanshipWorkmanship shall be in accordance
with good commercial practices as listed in Table 1 for
applicable acceptance levels.
2.6 Critical AreaSome portions of a part may be consid-
ered more critical than others. A critical area is here dened as
an area in which the presence of imperfections is considered to
be most detrimental. The areas of parts that are critical
structurally, aerodynamically, or electrically shall be uniform
and free of defects as listed in Table 1, if so stated on the
product drawing. Critical areas may be designated on the
product drawing by one of the following methods:
2.6.1 Encircle critical areas, or
2.6.2 Cross-hatch areas to designate areas of various levels,
or
2.6.3 Word description.
2.7 Allowable Defects, VisualThe defects in noncritical
areas which by nature, content, or frequency do not affect
serviceability of the part are designated as allowable defects.
Allowable defects shall be fully described as to type, size,
number, extent allowed, and spacing. The appropriate accep-
tance level (Table 1) for defects in these areas must be
specied. Where Level IV is used the defects must be fully
described on the product drawing. Defects greater than those
listed in the product specications, drawings, or contracts for
the part shall be cause for rejection.
1
This practice is under the jurisdiction of ASTM Committee D20 on Plastics and
is the direct responsibility of Subcommittee D20.18 on Reinforced Thermosetting
Plastics.
Current edition approved February 15, 1994. Published April 1994. Originally
published as D 2563 66 T. Last previous edition D 2563 70 (1987)e
1
.
1
Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
2.8 Repairable DefectsRepairable defects, if any, shall
consist of those which can be repaired without affecting the
serviceability of the part unless prohibited in the product
drawing or in the contract. Acceptable methods of repair shall
be agreed upon between the purchaser and the seller and shall
be only as specied in the product drawing or contracts for the
part.
2.9 Surface FinishThe over-all surface nish of laminates
may vary with the process used and the type of reinforcement.
Unless surface nish is specied on part drawings, contracts, or
orders from the purchaser, parts shall not be rejected for any
reading less than 150 rms. Defects shall be considered as not
included in over-all surface nish.
2.10 Surface AppearanceThe surface appearance or
color, or both, of laminated parts can vary considerably
depending on the process used to make the laminate, thickness,
type of reinforcement, type of resin, resin-to-reinforcement
ratio and the presence of defects. Any questions concerning
surface appearance and its inuence on the properties of the
part should be brought to the attention of the responsible
materials engineer.
3. Acceptance Levels
3.1 Visual InspectionEach part shall be checked visually
without the aid of magnication. Defects shall be classied as
to type and level as shown in Table 1 (see Note 2). The
acceptable quality level shall be determined by reference to the
part drawing for the applicable acceptance level for allowable
defects. If none of the rst three levels (Level I, II, III) is
considered applicable, the level shall be Level IV, and allow-
able defects must be specied on the product drawing. Any
excess of defects as specied under the required level shall be
cause for rejection. Unless otherwise specied, dimensions are
surface dimensions.
NOTE 2Typical defects as outlined in the word descriptions of Table
1 are illustrated in Figs. 1-21.
2
3.2 Acceptance Level IPresence of any defects in excess
of those listed in Table 1, Level I, shall be cause for rejection,
unless otherwise specied in Table 1, Level I.
3.3 Acceptance Level IIPresence of more than one defect
of those listed in Table 1, Level II, for each estimated 10 in.
2
of surface shall be cause for rejection, unless otherwise
specied in Table 1, Level II. No defect area shall be less than
2 in. from another.
3.4 Acceptance Level IIIPresence of more than two de-
fects of those listed in Table 1, Level III, for each estimated 13
mm (5 in.)
2
of surface shall be cause for rejection, unless
otherwise specied in Table 1, Level III. No defect area shall
be less than 1 in. from another.
3.5 Acceptance Level IVTo be specied on the product
drawing.
4. Keywords
4.1 reinforced thermosetting plastics; visual defects
TABLE 1 Allowable Defects
Name Denition
Visual Acceptance Levels
Level I Level II Level III
Chip a small piece broken off an edge or surface none maximum dimension of break, 3.0 mm
(
1
8 in.)
maximum dimension of break, 6.5 mm
(
1
4 in.)
Crack an actual separation of the laminate, visible on
opposite surfaces, and extending through the
thickness
none none none
Crack, surface crack existing only on the surface of the
laminate
none maximum length, 3.0 mm (
1
8 in.) maximum length 6.5 mm (
1
4 in.)
Crazing ne cracks at or under the surface of a
laminate
none maximum dimension of crazing, 13 mm
(
1
2 in.)
maximum dimension of crazing, 25 mm
(1 in.).
frequency and location to be determined by customer
Delamination, edge separation of the layers of material at the edge
of a laminate
none maximum dimension, 3.0 mm (
1
8 in.) maximum dimension, 6.5 mm (
1
4 in.)
Delamination,
internal
separation of the layers of material in a
laminate
none none none
Dry-spot area of incomplete surface lm where the
reinforcement has not been wetted with resin
none maximum diameter, 9.5 mm (
3
8 in.) maximum diameter, 14 mm (
9
16 in.)
Foreign inclusion
(metallic)
metallic particles included in a laminate which
are foreign to its composition
none none, if for electrical use; maximum
dimension, 0.8 mm (
1
32in.), 1/0.09
m
2
(1 ft
2
), if for mechanical use
none, if for electrical use; maximum
dimension, 1.5 mm (
1
16 in.), 1/0.09
m
2
(1 ft
2
), if for mechanical use
Foreign inclusion
(nonmetallic)
nonmetallic particles of substance included in a
laminate which seem foreign to its composition
none maximum dimension, 0.8 mm (
1
32in.),
1/0.09 m
2
(1 ft
2
)
maximum dimension, 1.5 mm (
1
16 in.);
1/0.09 m
2
(1 ft
2
)
Fracture rupture of laminate surface without complete
penetration
none maximum dimension, 21 mm (
13
16in.) maximum dimension, 29 mm (1
1
8 in.)
Air bubble (void) air entrapment within and between the plies of
reinforcement, usually spherical in shape
none maximum diameter, 1.5 mm (
1
16 in.);
2/in.
2
maximum diameter, 3.0 mm (
1
8 in.);
4/in.
2
Blister rounded elevation of the surface of a laminate,
with boundaries that may be more or less
sharply dened, somewhat resembling in shape
a blister on the human skin
none maximum diameter, 3.0 mm (
1
8 in.);
height from surface not to be outside
drawing tolerance
maximum diameter, 6.5 mm (
1
4 in.);
height from surface not to be outside
drawing tolerance
Burned showing evidence of thermal decomposition
through some discoloration, distortion, or
destruction of the surface of the laminate
none none none
2
Full-size (8 by 10-in.) glossy prints of these typical defects are available at a
nominal charge from ASTM Headquarters. Order Adjunct: ADJD2563.
D 2563
2
Name Denition
Visual Acceptance Levels
Level I Level II Level III
Fish-eye small globular mass which has not blended
completely into the surrounding material and is
particularly evident in a transparent or
translucent material
none maximum diameter, 9.5 mm (
3
8 in.) maximum diameter, 13 mm (
1
2 in.)
Lack of llout an area, occurring usually at the edge of a
laminated plastic, where the reinforcement has
not been wetted with resin
none maximum diameter, 6.5 mm (
1
4 in.) maximum diameter, 9.5 mm (
3
8 in.)
Orange-peel uneven surface somewhat resembling an
orange peel
none maximum diameter, 14 mm (
9
16 in.) maximum diameter, 29 mm (1
1
8 in.)
Pimple small, sharp, or conical elevation on the
surface of a laminate
none none maximum diameter, 3.0 mm (
1
8 in.)
Pit (pinhole) small crater in the surface of a laminate, with
its width approximately of the same order of
magnitude as its depth
none maximum diameter, 0.4 mm (
1
64 in.);
depth less than 1 percent of wall
thickness
maximum diameter, 0.8 mm (
1
32 in.);
depth less than 20 percent of wall
thickness
frequency and location to be determined by customer
Porosity (pinhole) presence of numerous visible pits (pinholes) none maximum of 25 pits (pinholes) in
porous area of size listed in Level II
maximum of 50 pits (pinholes) in
porous area of size listed in Level III
Pre-gel an unintentional extra layer of cured resin on
part of the surface of the laminate
(This condition does not include gel coats.)
none maximum dimension, 6.5 mm (
1
4in.);
height above surface not to be outside
drawing tolerance
maximum dimension, 13 mm (
1
2 in.);
height above surface not to be outside
drawing tolerance
Resin-pocket an apparent accumulation of excess resin in a
small localized area within the laminate
none maximum diameter, 3.0 mm (
1
8 in.) maximum diameter, 6.5 mm (
1
2 in.)
Resin-rich edge insufficient reinforcing material at the edge of
molded laminate
none maximum, 0.4 mm (
1
64in.) from the
edge
maximum, 0.8 mm (
1
32 in.) from the
edge
Shrink-mark (sink) depression in the surface of a molded laminate
where it has retracted from the mold
none maximum diameter, 9.5 mm (
3
8 in.);
depth not greater than 25 percent of
wall thickness
maximum diameter, 14 mm (
9
16 in.);
depth not greater than 25 percent of
wall thickness
Wash area where the reinforcement of molded plastic
has moved inadvertently during closure of the
mold resulting in resin-rich areas
none maximum dimension, 21 mm (
13
16 in.) maximum dimension, 29 mm (1
1
8 in.)
Wormhole elongated air entrapment which is either in or
near the surface of a laminate and may be
covered by a thin lm of cured resin
none maximum diameter, 3.0 mm (
1
8 in.) maximum diameter, 6.5 mm (
1
4 in.)
Wrinkles in a laminate, an imperfection that has the
appearance of a wave molded into one or more
plies of fabric or other reinforcement material
none maximum length surface side, 13 mm
(
1
2in.); maximum length opposite side,
13 mm (
1
2 in.); depth less than 10
percent of wall thickness
maximum length surface side, 25 mm
(1 in.); maximum length opposite side,
25 mm (1 in.); depth less than 15
percent of wall thickness
Scratch shallow mark, groove, furrow, or channel
caused by improper handling or storage
none maximum length, 25 mm (1.0 in.);
maximum depth, 0.125 (0.005 in.)
maximum length, 25 mm (1.0 in.);
maximum depth, 0.255 (0.010 in.)
Short in a laminate, an incompletely lled out
condition
NOTEthis may be evident either through
an absence of surface lm in some areas, or
as lighter unfused particles of material showing
through a covering surface lm, possibly
accompanied by thin-skinned blisters
none none none
D 2563
3
FIG. 1 Chips (A), Surface Cracks (B), Interply Delamination (C)
D 2563
4
FIG. 2 Crazing
D 2563
5
FIG. 3 Delamination by Improper Machining
D 2563
6
FIG. 4 Delamination
D 2563
7
FIG. 5 Dry-Spot
D 2563
8
FIG. 6 Foreign Inclusion
D 2563
9
FIG. 7 Fractures
D 2563
10
FIG. 8 Blister
D 2563
11
FIG. 9 Edge Segregation
D 2563
12
FIG. 10 Fish Eye
D 2563
13
FIG. 11 Lack of Fillout
D 2563
14
FIG. 12 Porosity
D 2563
15
FIG. 13 Pre-Gel
D 2563
16
FIG. 14 Resin-Pocket
D 2563
17
FIG. 15 Resin-Rich Crack
D 2563
18
FIG. 16 Resin-Rich Edge
D 2563
19
FIG. 17 Scratch
D 2563
20
FIG. 18 Shrink Marks
D 2563
21
FIG. 19 Wash
D 2563
22
FIG. 20 Worm Hole
D 2563
23
FIG. 21 Wrinkles
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org).
D 2563
24