Professional Documents
Culture Documents
5 Range Tops
5 Range Tops
5011.02.26 5-1
Food Service Technology Center
It can be said that the commercial range top is the most widely used piece of
commercial cooking equipment. In addition to being widely used, the range
top also is one of the most versatile cooking appliances, lending itself to nu-
merous burner (element) configurations. Ranges are available with either gas
or electric fuel sources, although gas dominates the market. Typically, a
range-top configuration consists of six open gas burners with a standard oven
incorporated underneath (see Figure 5-1). Though the commercial range top
is similar to the residential stove, the major difference is durability; a food
service range must withstand constant use and abuse while preparing tens or
hundreds of meals a day.
The top section of the range is referred to as the range top and consists of
burners or elements, which are used for cooking with pots and pans. The
oven that is built into a range is called a "range oven". Range ovens are most
often standard ovens sized to fit under the range top, though a growing num-
ber of manufacturers offer convection range ovens. Ovens are discussed in
detail in Section 7 of this report. Range-top configurations also may include
griddles and broilers; these appliances are detailed in Section 3 and 4, respec-
tively.
The configuration of a range is flexible by definition. The space underneath a
range top that is usually devoted to a range oven may instead house a refrig-
erated cabinet or storage space for pots and pans. Above and behind the
range top is the backshelf, which can accommodate an overfired salamander-
or cheesemelter-type broiler. Smaller ranges may include a narrow griddle
and/or charbroiler on either side of the range top.
Ranges are often divided into three categories depending on their intended
use: heavy-duty or hotel ranges, mediumduty or restaurant ranges, and spe-
cialty ranges such as stockpot and taco ranges. Heavy-duty ranges are built
for continuous use in high-volume operations such as large restaurants, hos-
pitals, and schools. They feature high-energy inputs and sturdy construction,
Introduction
Figure 5-1.
Six-burner range top
with range oven.
Range Tops
5011.02.26 5-2
Food Service Technology Center
with range tops built to support the weight of large stockpots and enough
power to heat such a vessel quickly. Restaurant ranges are more suited to a
smaller operation, such as a lunch counter or smaller restaurant. Medium-
duty ranges, although substantially built, are not as well suited for heavy use
or abuse, and often have lower energy inputs (e.g., range top burners of 15-
20 kBtu/h instead of a hotel range's 20-30 kBtu/h).
Induction range tops use electromagnetic energy to heat cookware made of
magnetic material (steel, iron, nickel or various alloys). When the unit is
turned on, the coils produce a high frequency alternating magnetic field,
which ultimately flows through the cookware. Molecules in the cookware
move back and forth rapidly, causing the cookware to become hot and cook
the food.
Specialty ranges are built to performa single function, as the name implies.
Stockpot ranges consist of one or two high-input open burners with a very
heavy-duty cast iron grate and are intended to cook large quantities of food in
one cooking vessel. Chinese ranges are designed for wok cooking and are
described in Section 6. An example of a specialty range is presented in Fig-
ure 5-2.
Range tops vary with fuel source and heating technology. Both gas burners
and electric elements can be built into restaurant range tops, although gas is
by far the most common. In hotel range tops, gas is almost universal.
Two or more range tops joined side-by-side is called a battery, often with
matching trim, countertop sections and possibly a front-mounted gas mani-
fold; such a range battery may stretch the length of a kitchen wall.
All range tops provide heat to a pot or pan frombelow. The method of heat
delivery to the pot may vary, but the cooking process is always a function of
the heat being delivered fromthe bottomof the pot/pan. One way in which
this cooking process may be affected is through the heated area, or size of the
heating pattern. Some range-top heating strategies provide uniformheat over
a larger area, while others concentrate it more in one spot. This becomes a
significant performance factor if the range top is used in a process such as
cooking pancakes, where surface uniformity is important; however, the
Figure 5-2.
Stock pot range.
Photo: Vulcan Hart
Cooking Processes
Range Tops
5011.02.26 5-3
Food Service Technology Center
choice of pan construction and materials can be used to mitigate unevenness
in the heating source.
Range tops are generally not amenable to timers or cooking computers, and
most range top cooking demands the attention of the operator. Controls on
the range top are typically very simple. There is most often an infinite-
control knob to regulate the input of each burner or element. The controls are
calibrated in terms of the percentage of input, as the burner does not gener-
ally sense the temperature of the pot.
An exception to this rule is the induction ranges top, which has a tempera-
ture-limiting switch to guard against the pot-melting temperatures that this
type of unit can produce. In addition, induction range tops will often have a
microprocessor for temperature control. J ust beneath the glass cook top is a
tiny temperature sensor that connects to the microprocessor. When the tem-
perature control is set to a particular temperature, the microprocessor moni-
tors the temperature and cycles the induction hob on and off to maintain the
desired temperature.
Gas burners and electric elements can be described as "open" or "closed".
The most common type of range top uses open burners, applying flame di-
rectly to the bottomof the pot. Open tops generally offer fast heat-up, but can
have slow cleanup, as spills can fall directly onto the burner or below.
Cleanup may mean moving or removing parts of the range top to reach the
mess. A closed burner or element seals the heat source under a ceramic, glass
or metal cover, presenting a smooth surface to the bottomof the cooking ves-
sel. This makes it easy to slide pots and pans on and off of the hot spots, and
also eases cleanup.
Each heating technology described here comprises a different type of burner
or element. Manufacturers commonly allow the user to specify a combination
of burner or element configurations that will best suit their specific needs.
Controls
Heating
Technologies
Range Tops
5011.02.26 5-4
Food Service Technology Center
Open Burners and Discrete Elements
Open Gas Burners. Open gas burners remain the burner-of choice for most
operators. They are inherently sturdy, inexpensive, and they respond in-
stantly when the burner is turned on and adjusted. The visible flame provides
direct feedback on the heat to the pan, enhancing the operators control, and
can ignite spattered grease to flash flame inside the pan during display
cooking.
The gas burner has two designs. The first is a hollow ring of cast iron or steel
with holes that jet gas upwards towards the cooking vessel (Figure 5-3). A
newer but similar design is the star burner, which has arms radiating froma
central hub spreading its flame more evenly over the pot bottom(Figure 5-4).
Each burner design has the gas mixed with primary air at an air shutter on the
manifold. Secondary air provides most of the oxygen for combustion, com-
bining with the gas as it jets fromthe burner. The flame is controlled with a
gas valve mounted on the front of the range.
The burner is set into the surface of the range top and covered by a metal
grate, which supports the cooking vessel. Grates are designed so that pots can
be slid easily fromburner to burner, and are stable in any position. Normally
with this grate design, a spill tray will be underneath the burner to catch fal-
ling particles and/or drips. The grates may be removable, and on some range
tops the burner heads lift off for easy cleaning.
The typical input rating for an open gas burner is 20 to 25 kBtu/h, with
manufacturers offering 30 kBtu/h burners as an option. Until recently, the
higher-input burners only were used in the most demanding production ap-
plications. However, they now are becoming the industry standard for heavy-
duty ranges. Studies at the FSTC indicate that, under normal operating condi-
tions, these higher input burners do not use significantly more energy to cook
as one might intuitively think. Although the gas input is higher, the cook time
is correspondingly shorter.
1
However, the net effect of these more powerful
burners could be an increase in energy consumption if the burners were left
on between cooking events as sometimes happens in high profile display
kitchens or on saut lines.
Figure 5-3.
Ring burner.
Photo: Fisher-Nickel, inc.
Figure 5-4.
Star burner.
Photo: Fisher-Nickel, inc.
Range Tops
5011.02.26 5-5
Food Service Technology Center
Electric Speed Coils. Sheathed electric coils, wound into a spiral element,
are used on light- and medium-duty restaurant ranges. See Figure 5-5. These
elements also are known as speed coils. Analogous to the elements on a
residential electric range, they provide fast heat and response. They are rela-
tively fragile though and not recommended for use with heavy stockpots.
Electric French Plates. (Also called round plates.) In a French plate ele-
ment, the open electric coil is covered with a solid metal disk. They are gen-
erally 6-10 inches (150-250 mm) in diameter, and protrude to inch (6 to
12 mm) above the range top. By concentrating heat under the pot, they pre-
heat faster than an electric hot top, and are more durable and easier to clean
than an electric speed coil. Figure 5-6 shows an electric range with French
plates.
Closed Burners and Elements
Gas Hot Tops. The hot top is a flat metal plate made of cast iron or steel,
heated fromunderneath by atmospheric gas burners. The bottomof the plate
may be flat, textured, or finned to distribute heat evenly. The surface of the
hot top reaches temperatures of 800F-1000F (425C to 540C) at the
maximuminput. Some hot tops are constructed so that there is a temperature
gradient fromfront to back, allowing different styles of cooking on the same
section. The hot-top section is typically 24 inches (600 mm) deep and 12-18
inches (300-450 mm) wide. A range top may consist of several sections, each
having its own burner and control knob.
Hot tops allow the entire surface of the range top to be used, instead of only
the space directly over the burners. This allows an operation that prepares
many small orders at once to fit more pans on the range top. Pots slide across
the flat surface more easily than across the grids on an open-burner range
top. This facilitates moving items such as soups or stews froma front hot-
top section that is set at a high temperature (i.e., for boiling) to an alternate
section that is set at a lower temperature (i.e., for continued simmering or
holding). However, the hot top is slow to heat: it may take 30 to 60 minutes
before the plate reaches its maximumtemperature setting. Similarly, it is
slow to respond to changes in the control setting.
Figure 5-5.
Electric speed coil.
Photo: Clarkenergy.com
Figure 5-6.
French plate range top.
Photo: Garland Range.
Range Tops
5011.02.26 5-6
Food Service Technology Center
Hot tops are typically preheated in the morning and left on at maximum input
throughout the day. They consume energy at a high rate, and radiate more
heat into the kitchen than any other type of range top. The energy input rates
are from20-40 kBtu/h per section.
One alternative to the high energy consumption of the hot top is the open
grate top. This range top has a continuous flat surface like a hot top but sur-
face is comprised of a grate instead of a solid plate. This configuration re-
duces the heat-up time of the top and allows the operator to see the burners
and control themmore accurately. Ultimately, the operator has the work sur-
face associated with a hot top combined with the speed and flexibility of an
open burner range top. This style of level-surface grate is becoming a stan-
dard feature on most heavy-duty, open-burner ranges.
Gas Radiant Hot Top. (Also called French top or pot ranges) This is a spe-
cialized hot top in which the metal plate is inset with removable concentric
rings. The rings may be removed to expose more of the cooking vessel to the
direct flame of the burners. This style of hot top uses very high-powered
burners with inputs up to 45 kBtu/h. In this case, the controls on the range
top allow the operator to adjust input to each ring separately.
Electric Hot Tops. Electric hot tops are not common. They are identical in
construction and detail to the gas hot top, except the heat source is an electric
element clamped to the bottomof the plate. Electric hot tops are rated from
5 kW to 7.5 kW per section.
Induction Cook Tops. The electric induction range is significantly different
fromother types of ranges. An induction cooktop by and large consists of a
single hob (burner), but two-hob units are available, with the exception of
Europe and Asia, where six-hob units are offered (note that a U.S. manufac-
turer had a six-hob unit was on display at the 2002 National Restaurant As-
sociation show in Chicago). The range surface is a smooth and continuous
ceramic glass plate. Because it is not directly heated during operation, the
surface remains relatively cool, gaining residual heat fromthe cooking con-
tainer. These units offer precise temperature control and are more efficient
because the cookware is heated directly, without the need to preheat heat the
cooking surface.
Range Tops
5011.02.26 5-7
Food Service Technology Center
A recent addition to the induction range family is the induction wok. These
units offer high production capacity in a small package and without the need
to water-cool the surrounding surface, as with traditional gas woks. They do
employ a different control mechanismfromtraditional woks and may not be
a direct replacement for gas-fired Chinese ranges in traditional Asian cook-
ing. Induction units are by far the most energy efficient type of range avail-
able.
Technologies developed for commercial use have focused on improving gas
burner efficiencies, and on designing easy-to-clean closed range tops for both
gas and electric ranges.
Power Burners
Power burners premix gas and air in stoichiometric proportions for efficient
combustion. Because no secondary air needs to be drawn into the flame at
the burner head, the grate can be constructed to forman almost airtight
chamber beneath the pot. This eliminates the rapid convection that washes
much of a conventional burner's heat up and around the cooking vessel.
Thus, more of the hot-combustion products transfer heat to the bottomof the
vessel. The intense heat of the power burner presented its own obstacle. The
initial commercial release was halted because users complained about pots
warping on the new burners, as a result of underestimating the cooking speed
and allowing pots to boil dry.
Testing by the American Gas Association Laboratories (AGAL) showed a
power burner to be 36% faster and use 34% less energy than a conventional
20 kBtu/h star burner.
2
Although the initial cost of a power-burner is higher
than a standard burner, AGAL estimated that energy savings would compen-
sate for the cost difference in less than two years.
Sealed Combustion
The Canadian Gas Research Institute (CGRI) developed a prototype range
top, which featured standard gas burners under a glass ceramic surface.
3
Each
Advanced
Technologies
Range Tops
5011.02.26 5-8
Food Service Technology Center
burner is surrounded by a ceramic cup, which is heated to over 1200F
(650C) during operation. Heat is supplied to the cooking vessel by conduc-
tion through the glass ceramic surface and by radiation fromthe burner flame
and ceramic enclosure. An over-limit switch shuts the burners off if the tem-
perature of the ceramic glass top rises outside the operating range.
The burners are completely enclosed, and all combustion products are vented
outdoors. This closed-burner design has the appeal of easy cleanup, a visible
heat source and according to Gas Technology Institute (GTI), a higher effi-
ciency than standard gas open burners.
The current sealed-combustion prototype is for residential applications. The
unit's easy cleanup, speed and lower heat gain to the kitchen also would be
valuable in a food-service setting.
Gaz de France, as part of their strategy to help the foodservice industry, and
in concert with commercial cooking equipment manufacturers, has intro-
duced a patented Vitrogaz ceramic hot plate. It features a smooth, flat, easy
to clean cooking surface and is powered with two high-performance,
27 kBtu/h radiant burners. It can be used with an open flame or as a solid-top
plate. Plate temperatures are adjustable between 140F and 1112F (60C
and 600C).
4
Infrared Burners
Infrared burners force gas and air through a ceramic burner. The surface of
the burner, where combustion takes place, is perforated with thousands of
pores. During operation the ceramic burner face reaches temperatures above
1600F (870C). Infrared burners are more efficient than the standard gas
burner, but they have not yet been successfully applied to the commercial
food service range top.
A setback lies in spilled food product clogging the burner holes. A solution is
the infrared jet-impingement burner, which uses an infrared ceramic burner
beneath a perforated glass-ceramic plate. The glowing ceramic burner trans-
mits radiant heat to the cooking container, and the combustion products are
propelled through the holes in the ceramic glass shield to impinge on the bot-
tomof the pot. The shield prevents spillage fromdripping onto the burner,
Range Tops
5011.02.26 5-9
Food Service Technology Center
and what does flow through the holes is incinerated. The developer, Tecogen
Inc., rates the ease of cleaning these burners as somewhat better than con-
ventional burners. The developer reports a water boil efficiency of 66% as
opposed to 40% for a regular burner.
5
Halogen Range Tops
Halogen range tops share two of the major advantages of the induction range
topfast response to controls and a sealed cooking surface. In addition, the
halogen elements glow red in proportion to the energy input, providing visual
feedback of heat intensity. Unlike induction range tops, the cooking surface
does heat up, and power does not instantly modulate to idle when the pot is
removed.
The heat source for this range top is a set of halogen lamps beneath a glass
ceramic cooktop. Pots and pans rest directly on the ceramic and are heated by
radiant energy fromthe lamps. An over-limit switch monitors the glass ce-
ramic material, cutting off the power when the temperature of the cooktop
exceeds safe limits. The efficiency of a residential halogen cooktop has been
reported at 52%-58%.
6
Currently this technology is not available in commer-
cial range units.
Automatic Burner Shut Off and Re-Ignition.
In catering kitchens it is often more practical to leave open-flame burners lit
when not being used, rather than turning the gas off and re-lighting it each
time when needed. Gaz de France, along with Madec-Mater Company, has
patented the Top-Flaman automatic shut-off and re-ignition device that is
triggered by cookware detection. They proclaim energy savings around
50%.
4
A similar burner control systemwas developed in the United States by Leo-
nard Grech and documented by the U. S. Department of Energys Office of
Industrial Technology. This system uses a small, vertically mounted, spring-
loaded piston that controls a gas valve. When a pot is placed on the burner,
Range Tops
5011.02.26 5-10
Food Service Technology Center
the piston is depressed and the gas valve is opened. When the pot is removed,
the piston returns to its original position and the burner is turned off.
Performance Evaluation Criteria
ASTM Standard F 152196 Standard Test Methods for Performance of
Range Tops
7
, developed at the Food Service Technology Center,
provides a
means to compare performance and energy use of range tops
8
.
The test method covers the performance of gas and electric range tops, in-
cluding discreet burners and elements, as well as hot tops. The application of
the test method provides results for maximumrate of energy input, tempera-
ture uniformity of heating surface, cooking-energy efficiency and production
capacity.
Measuring the temperature uniformity of a steel plate emulating the bottom
of a frying pan can simulate the heat-transfer characteristics of a cooking
unit. Applying this test procedure gives the temperature at several points
across the area of a pot's bottom, indicating hot or cold spots.
Production capacity is the amount of food that a burner or element can cook
in a given time, expressed as gallons of water that can be raised from70F to
200F (21C-93C) in one hour. This provides an indication of the speed
of a burner.
Maximumrate of energy input is a rough index of the power of a range
top. The test method reports the total energy input rate for all the burners on
a range top. It is more common in catalogs to see a rating for individual
burners or elements. For a given type of burner or element, a higher rate of
energy input generally indicates that the burner can supply more heat to the
pan. This is only true when comparing similar burners; a high-efficiency
burner can use less energy, but performmore work than a low-efficiency
burner (i.e., cook the same quantity of food in less time).
The American National Standard Institute (ANSI) for Gas Food Service
Equipment Ranges and Unit Broilers (Z83.11 1989) section 2.12
9
alsode-
tails test criteria and methods for evaluating the efficiency of an open gas
range top. ANSIs test requirement is similar to ASTM with some minor dif-
Range Top
Performance
Range Tops
5011.02.26 5-11
Food Service Technology Center
ferences. Table 5-1 compares the test criteria between ASTM F1521-96 and
ANSI Z83.11 1989.
Table 5-1. Comparison of ASTM and ANSI Range Top Efficiency Tests.
ASTM
F1521-96
ANSI Z83.11
Proposed
Revisions to
ASTM F1521-96
a
Stabilization
Time (min.)
30
30
30
Temperature
Rise (F)
130F
130F
130F
Control Setting Maximum Maximum Maximum
Pot Diameter
(inches)
12
<15,000 Btu
9.5
15,000 to
25,999 Btu
13
>26,000 Btu
16
13
Water
Weight (lbs)
20
N/A
(10)
b
N/A
(20)
b
N/A
(29)
b
20
Water
Depth (inches)
N/A
(5)
c
4
N/A
(4)
c
a
Proposed change from12-inch stockpot to 13-inch stockpot has been accepted by the F26 ASTM techni-
cal committee.
b
Measured water weight with respect to 4-inches of water depth. Note: Water weight is not specified in
ANSI Z83.11
c
Measured water depth with respect to 20 pounds of water in the specified pot. Note: The ASTM test
method specifies water weight instead of water depth since weight can be determined more accurately.
Table 5-1 shows that specified stabilization times, temperature rise, and
power settings are identical for the two methods. The differences are the di-
ameter of the pots and the weight and depth of water. Based on the outcome
of investigating these latter differences, researchers at the Food Service
Technology Center will initiate a proposal to revise ASTM F1521-96 to be
consistent with ANSI Z83.11. The proposed changes are as follows:
1. Change the ASTM specification froma 12-inch diameter pot to a 13-inch
diameter pot to match ANSIs requirement for a range top with an energy
input rate between 15,000 25,999 Btu/h (Update: proposed change has
been accepted by F26 ASTM Technical Committee; revision will be
made to the current test method).
Range Tops
5011.02.26 5-12
Food Service Technology Center
2. Adopt 13-inch diameter pot test for all burner types and input rates on
standard range tops.
3. Add an extra-heavy load test using a 16-inch diameter pot.
4. Water weight will remain as the test criterion in the ASTM test, since
weight is an accurate method of measuring water, and this value needs to
be precise for the efficiency calculation.
Cooking-energy efficiency, as defined by the ASTM Standard Test Method
for Performance of Range Tops,
7
is the ratio of the amount of energy going
into the food versus the amount of energy supplied to the burner:
% 100 =
Appliance
Food
E
E
iciency CookingEff
Energy efficiency is determined by heating water from70 to 200F (21 to
93C) at the full-energy input rate. Using FSTC data generated by the ASTM
method
7
, along with data fromthe Minnesota study
10
and range top devel-
opment and testing by AGAL,
11,12
benchmark energy efficiencies are pre-
sented in Table 5-2.
The efficiency of gas range tops has received attention fromboth the manu-
facturer and the end user.
13
Research organizations such as the GTI have
been instrumental in attempting to develop and bring high-efficiency gas
models to the US market. Standard electric range tops, at roughly 65-75%,
are already quite efficient. With the introduction of induction technology,
electric range top efficiencies are approaching 85%.
Table 5-2. Range Top Energy Efficiency.
a
High Efficiency Gas (%) Standard Gas (%) Electric. (%)
30 - 40 25 - 30 65 - 85
a
Energy efficiency numbers for range tops are best estimates based on FSTC test data from applying ASTM Stan-
dard Test Methods to four different range tops
1,14-16
, on preliminary results from revising the existing ASTMStandard
and applying it to three electric induction units
18-19
and on data from both the Minnesota Study
10
and AGAL test-
ing
9,11,12
.
Benchmark Energy
Efficiency
Range Tops
5011.02.26 5-13
Food Service Technology Center
Projected energy consumption for gas and electric range tops are presented in
Tables 5-3 and 5-4. The energy consumption rates for the range tops and
range ovens are based on in-kitchen monitoring of gas and electric ranges,
outfitted with either a standard or a convection oven, in the Pacific Gas and
Electric Company production-test kitchen.
20-26
The duty cycle was calculated
by dividing the daily energy consumption rate by the appliance median en-
ergy input rate. Typical operating hours were obtained fromin-kitchen en-
ergy-use monitoring experiences and observations as well as fromthe PREP
study
27
and a proprietary end-use monitoring report. Projected annual energy
consumption was determined by assuming a 6-day per week, 52-week per
year operation.
Table 5-3. Projected Energy Consumption for Gas Ranges.
Nominal
Size
Rated
Energy
Input
Duty
Cycle
Avg. Energy
Consumption
Typical
Operating
Hours
Annual
Energy
Consumption
(kBtu/h) (%) (kBtu/h)
a
(h/d)
b
(kBtu)
c
Range Top 6 Burners 120 - 210
(Median) 165 20 32 12 120,000
Range Oven 35 - 45
(Median) 40 40 16 8 39,900
Total Range 205 48 160,000
a
Average energy consumption rates are based on monitoring five gas ranges in a real-world production kitchen.
20-24
b
Operating hours or appliance "on time" is the total period of time that an appliance is operated from the time it is
turned "on" to the time it is turned "off".
c
The annual energy consumption calculation is based on the average energy consumption rate x the typical operating
hours x 6 days per week x 52 weeks per year.
Range Top Energy
Consumption
Range Tops
5011.02.26 5-14
Food Service Technology Center
Table 5-4. Projected Energy Consumption for Electric Ranges.
Nominal
Size
Rated
Energy
Input
Duty
Cycle
Avg. Energy
Consumption
Typical
Operating
Hours
Annual Energy
Consumption
(kW) (%) (kW)
a
(h/d)
b
(kWh)
c
(kBtu)
d
Range Top 6 elements 12
(Median) 12 25 3 12 11,200 38,300
Range Oven 8
(Median) 8 25 2 8 4,990 17,000
Total Range 5 16,200 55,300
a
Average energy consumption rates are based on monitoring two electric ranges in a real-world production
kitchen.
25,26
b
Operating hours or appliance "on time" is the total period of time that an appliance is operated from the time it is
turned "on" to the time it is turned "off".
c
The annual energy consumption calculation is based on the average energy consumption rate x the typical operating
hours x 6 days per week x 52 weeks per year.
d
Conversion Factor: 1 kW= 3.413 kBtu/h.
Ranges are classified as mediumduty fromthe perspective of exhaust venti-
lation. For a sidewall canopy hood, the design ventilation rate for ranges
would range from200- 300 cfm(100-150 L/s) per linear foot of wall canopy
hood.
Gas range tops have historically had several advantages over electric range
tops. Gas is faster with no wait for preheating. Gas is more responsive: an
adjustment to the controls changes the heat to the pan bottomimmediately.
Gas is more durable: heavy-duty construction and long life are hallmarks of
gas-range construction. Gas is inexpensive: even though a gas range operates
at a lower efficiency, the operating cost is often half that of an electric range
top.
In turn, electric range tops have had the advantage of high efficiency and are
easier to clean when closed burners are used. The induction range top com-
bines these features with a serious challenge to the superiority of gas in speed
and responsiveness. It is an easy to clean, fast heat source with a discrete-
load cooking efficiency of over 80%, and it adds little heat to the kitchen. In
real world cooking, induction saves even more energy by dropping to, effec-
Ventilation
Requirements
Research and
Development
Range Tops
5011.02.26 5-15
Food Service Technology Center
tively, zero energy input the instant a pot is removed fromthe element, and
coming back to full input when the pot is replaced. Although induction range
tops have not yet been proven by years of use in the food service kitchen and
the durability of the electronics and ceramic cooktop remains to be seen, they
represent a credible challenge in a category that has historically been domi-
nated by gas appliances.
In response, the gas industry initiated an advanced range top development
project with the goal of modernizing the standard gas range and reinforcing
its market dominance. Drawing on research performed by Arthur D. Little,
the Food Service Technology Center, and Gaz de France, and with the addi-
tional support of Enbridge Gas Distribution, the Southern California Gas
Company, and the Gas Technology Institute, the Canadian Gas Research In-
stitute (CGRI) published an Assessment of Technical Strategies for an Ad-
vanced Commercial Gas-Fired Rangetop
28
. This report was further refined
into a Summary Report on an Advanced Rangetop for Presentation to End-
Users, Rangetop Manufacturers and Government Agencies
29
. The goals of
this research were to create a gas range with:
29
Improved cooking efficiency/ productivity,
Reduced energy consumption,
Reduced maintenance/easy cleanabilitiy, and
Improved food quality/consistency.
The assessment presented three advanced range top options
29
:
1. State-of-the-Art Rangetop with Atmospheric Burner incorporating open
top atmospheric burners with enhanced cleanability and boil booster and
simmer capability.
2. Rangetop with Enhanced Output / Heat Transfer incorporating power
burner technologies and/or atmospheric pressurized burner concepts.
3. Smooth Top Rangetop features a closed smooth top with high efficiency
radiant burners.
Range Tops
5011.02.26 5-16
Food Service Technology Center
All three of these options included improved burner technologies, incorpora-
tion of an energy saving device/ burner control system, and elimination of
standing pilots.
While there are technical issues that must be overcome before the advanced
range is a market reality, the reports conclusion was that it was possible to
create an improved range top that met the expectations of end-users and in-
dustry alike and that the payback would range fromone to four years.
29
With this in hand, the gas industry (with GTIs lead) has continued work on
the advanced gas range, focusing on developing commercial grade ceramic
tops and sealed elements, and higher efficiency burners.
Future research should continue along these paths, with emphasis on the fol-
lowing:
Further development of the sealed combustion range top for commercial
food service. This technology would allow ventilation at lower airflows
and reduce kitchen heat gain, as well as provide a desirable closed cook-
top.
Development of a hot top using infrared burners. This technology is al-
ready applied to analogous appliances such as griddles, and would re-
duce energy costs for gas hot tops.
Development of higher efficiency, low-first-cost open gas burners.
Investigate the feasibility of the cooking vessel sensor. Open gas burners
should take advantage of their traditional strengthinstant heatby turn-
ing off when the pot is removed, and then back on when it is replaced.
This can increase the cost advantage of gas, and provides a response to
one of the strong features of the induction range top: zero idle energy us-
age. This will also reduce heat gain to the kitchen.
Development of cooking vessel temperature feedback. An over limit
switch to cut input when a pot has heated to the point of warping would
allow further marketing of the power burner. If sensitive enough, such a
device could begin to automate cooking. For example, a stockpot could
be brought to a boil and then held at simmer.
Range Tops
5011.02.26 5-17
Food Service Technology Center
Inclusion of the NAFEM Online Kitchen protocol compliant technology
into the range control system.
Induction rangetops are rapidly gaining popularity within the commercial
food service world. With recent improvements to the induction electronics
and significant reductions in first cost, the induction rangetop will inevitably
begin to impact the market share of the traditional gas range. The gas indus-
try must continue to evolve the design and functionality of the gas range top
if this appliance is to retain its current market dominance.
Froma conservation perspective, gas utilities should promote the use of open
burner or open-grate hot tops over full-hot tops. This can significantly reduce
operating costs of ranges and heat gain to the kitchen.
Industry Market
Focus
Range Tops
5011.02.26 5-18
Food Service Technology Center
1. Young, R., Cesio, C., 1995. Montague Model V136-5 Heavy-Duty
30,000 Btu/h Open Top Gas Range: Application of ASTM Standard Test
Method F1521-94. Food Service Technology Center Report 5011.94.6,
October.
2. American Gas Association, Food Facilities and Energy News: Advances
in Gas Cooking Technology into the 1990san educational supplement
published 13 times a year and bound into Restaurants and Institutions
and Foodservice Equipment & Supplies Specialist magazines under the
direction of AGA.
3. Canadian Gas Research Institute, 1992. Gas Technology Update: De-
velopment of a Sealed Combustion Gas Range. Bulletin Number 2, Au-
gust.
4. Gaz de France, 1992. Gas Utilization Research Centre, Research and
Development Division CERUG Activities Report, pp.24.
5. Gas Research Institute. Advanced Residential and Light Commercial
Cooktop Burner: a GRI Field Test Status Report.
6. Gas Research Institute, 1995. Project
7. American Society for Testing and Materials, 1996. Standard Test
Method for Performance of Range Tops. ASTM Designation F1521-96.
In Annual Book of ASTM Standards, West Conshohocken, PA.
8. Young, R., 1995. Development and Validation of a Uniform Testing
Procedure for Range Tops. Food Service Technology Center Report
1022.95.20, October.
9. American Gas Association, J uly 1989. Gas Food Service Equipment
Ranges and Unit Broilers. ANSI Z83.11 1989.
10. Snyder, O.P., and J .F. Norwig., March 1983. Comparative Gas/Electric
Food Service Equipment Energy Consumption Ratio Study. University
of Minnesota.
11. American Gas Association, 1986. Performance Evaluation Methods:
Convection, Deck, and Range Ovens. Prepared for the Gas Research In-
stitute, GRI-87/0182, December.
12. Himmel, R.L. and Stack, R.E., 1981. Commercial Cooking Equipment
Improvement, Volume I: Range Ovens. American Gas Association
Laboratories report to the Gas Research Institute, GRI-80/0079.1, Octo-
ber.
13. Little, Arthur D. Inc., August 1993. Characterization of Commercial
Building Appliances: Final Report for Building Equipment Division Of-
fice of Building Technologies U.S. Department of Energy, pp. 5-40.
14. Young, R., Cesio, C., 1995. Montague Model V136-5 Heavy-Duty Open
Top Gas Range: Application of ASTM Standard Test Method F1521-94.
Food Service Technology Center Report 5011.94.4, October.
References
Range Tops
5011.02.26 5-19
Food Service Technology Center
15. Young, R., Cesio, C., 1995. Vulcan-Hart Model VR-4 Heavy-Duty Elec-
tric Range: Application of ASTM Standard Test Method F1521-94. Food
Service Technology Center Report 5011.94.7, October.
16. Young, R., Cesio, C., 1995. Toastmaster