PS - 739 - June 2014
PS - 739 - June 2014
RAYMOND T. ODIERNO
General, United States Army Chief of Staff
Official:
GERALD B. OKEEFE
Administrative Assistant to the Secretary of the Army
1408501
Stryker AFES PMCS
Stryker Run-flat Tire Tips
Stryker Slat Armor Protection
Stryker Roof Storage
M1-Series Tank Turret Safety Screens
M1-Series Tank Turret Bolts, Roadwheel Mount
2-3
4
5
6-7
7
8-9
COMBAT VEHICLES 2
10 TACTICAL VEHICLES
FMTV Cargo Cover Kit NSNs
Trailer Gladhand Color Coding
10-20
21
Installing M230 Gun Parts
OH-58D M3P Gun Firing Prep
OH-58D Mast Mounted Sight Servicing
OH-58D Wand Assembly No Slip Tip
OH-58D Weapons Cables Inspection
22
23
24
25
26
COMMUNICATIONS 46
46-51 BETSS-C Generator PM
Patriot Simplified Survey System PM 35
M240H and M240L TM Changes
M2010 Sniper Rifle Turn-In Guidance
Safety Wire Methods
M110 SASS Sight Dust Cover NSNs
MK 19 Model Identification
M16-Series Rifle Sight Posts
JBPDS BIDS Generator PM
M240-Series Loose Op Rod Pin
M153 CROWS II Travel Locks
36-37
38
39
39
40
41
42-44
44
45
MISSILES 35
SMALL ARMS 36
AVIATION 22
The Battle for PM 27-34
Connies Post Scripts 60-61
MSD Software Updates Improve IETM Results
DILNet Lists Hardware Inventory
milSuite Online Connections
COEI, BII, AAL and Expendable/Durable Supplies
Drivers Training Check Ride Policy
Estimated Ship Dates on LIW
52
53
54-55
56
57
58-59
LOGISTICS MANAGEMENT 52
You are invited to send PS your ideas for improving maintenance
procedures, questions on maintenance and supply problems and
questions or comments on material published in PS.
Just write to:
MSG Half-Mast
PS, the Preventive Maintenance Monthly
USAMC LOGSA (AMXLS-GP)
Bldg. 3303
Redstone Arsenal, AL 35898
Or email to:
[email protected] or
[email protected]
Internet address:
https://www.logsa.army.mil/psmag/pshome.cfm
PS, The Preventive Maintenance Monthly (ISSN 0475-2953) is published monthly by the Department of the Army, Redstone
Arsenal, AL 35898. Periodical postage is paid at the Huntsville, AL post office and at additional mailing offices.
Postmaster: Send address changes to PS, The Preventive Maintenance Monthly, USAMC LOGSA (AMXLS-GP), Bldg. 3303, Redstone
Arsenal, AL 35898.
ISSUE 739 JUNE 2014
TB 43-PS-739, The Preventive Maintenance Monthly, is an official publication
of the Department of the Army, providing information for all Soldiers assigned
to combat and combat support units and all Soldiers with unit maintenance
and supply duties. All information published has been reviewed and approved
by the agency responsible for the equipment, publication or policy discussed.
Application of the information is optional with the user. Masculine pronouns may
refer to both genders. The use of product or company names does not constitute
endorsement of those products, services or companies by the U.S. Army. The
use of non-DoD hyperlinks, along with their content, does not constitute
endorsement by DoD or DA. Neither DoD nor DA exercises any editorial control
over, and cannot vouch for, content on non-DoD websites.
CARGO COVER NSNS, SEE PAGES 10-20
Issue 739
June
2014
TB 43-PS-739
Approved for
Public Release;
Distribution is
Unlimited
and you
oRdered
the covers
when?
I couldnt
find the NSN.
CARGO COVER NSNS, SEE PAGES 10-20
PM for you
means taking
care of
yourself:
Drink plenty
of water to
replace what
you sweat out.
Rub insect
repellant with
DEET on your
skin so the bugs
dont feast
on you.
Protect your
skin with sun
screen, your
hearing with
combat arms
earplugs and
your eyes
with combat
eyewear.
PM for your
equipment starts
with your hydration
system.
Make sure it works
properly, because
you wont last long
in the heat without
water. Check for
leaks. Disinfect the
bladder so your
water doesnt
taste foul.
Then inspect the
soft panels and
hard inserts in
your body armor.
if theyre damaged
by bullets or
fragments,
they cant save
your life.
Replace them.
And finally, a word about your
vehicle: You dont want your ride to
break down in hostile territory. A
disabled vehicle attracts enemy fire.
So check your batteries charge
levels and the engines fluids daily.
Check tire pressure. And make sure
you keep the air filter clean.
Fine dust and sand are the
greatest threats to your equipment.
They can cripple your gear quickly
and quietly.
To keep communicating, put dust
caps on radio connectors.
To keep shooting, clean your rifle
and magazines as often as needed.
Keep their outsides wiped dry.
By order of the Secretary of the Army:
RAYMOND T. ODIERNO
General, United States Army Chief of Staff
Official:
GERALD B. OKEEFE
Administrative Assistant to the Secretary of the Army
1408501
Summer is here. The sun is high in the
sky and burning bright. Temperatures
are soaring. The soils parched and
the air is thick with dust.
Here are a few preventive
maintenance lessons from
Soldiers whove spent time
in the sandbox
Your Best
Insurance
Preventive maintenance is your
best insurance against THE
threats youll face this summer!
Make a pledge to practice preventive
maintenancefor you and your equipment.
Stryker AFES PMCS
Stryker Run-flat Tire Tips
Stryker Slat Armor Protection
Stryker Roof Storage
M1-Series Tank Turret Safety Screens
M1-Series Tank Turret Bolts, Roadwheel Mount
2-3
4
5
6-7
7
8-9
COMBAT VEHICLES 2
10 TACTICAL VEHICLES
FMTV Cargo Cover Kit NSNs
Trailer Gladhand Color Coding
10-20
21
Installing M230 Gun Parts
OH-58D M3P Gun Firing Prep
OH-58D Mast Mounted Sight Servicing
OH-58D Wand Assembly No Slip Tip
OH-58D Weapons Cables Inspection
22
23
24
25
26
COMMUNICATIONS 46
46-51 BETSS-C Generator PM
Patriot Simplified Survey System PM 35
M240H and M240L TM Changes
M2010 Sniper Rifle Turn-In Guidance
Safety Wire Methods
M110 SASS Sight Dust Cover NSNs
MK 19 Model Identification
M16-Series Rifle Sight Posts
JBPDS BIDS Generator PM
M240-Series Loose Op Rod Pin
M153 CROWS II Travel Locks
36-37
38
39
39
40
41
42-44
44
45
MISSILES 35
SMALL ARMS 36
AVIATION 22
The Battle for PM 27-34
Connies Post Scripts 60-61
MSD Software Updates Improve IETM Results
DILNet Lists Hardware Inventory
milSuite Online Connections
COEI, BII, AAL and Expendable/Durable Supplies
Drivers Training Check Ride Policy
Estimated Ship Dates on LIW
52
53
54-55
56
57
58-59
LOGISTICS MANAGEMENT 52
You are invited to send PS your ideas for improving maintenance
procedures, questions on maintenance and supply problems and
questions or comments on material published in PS.
Just write to:
MSG Half-Mast
PS, the Preventive Maintenance Monthly
USAMC LOGSA (AMXLS-GP)
Bldg. 3303
Redstone Arsenal, AL 35898
Or email to:
[email protected] or
[email protected]
Internet address:
https://www.logsa.army.mil/psmag/pshome.cfm
PS, The Preventive Maintenance Monthly (ISSN 0475-2953) is published monthly by the Department of the Army, Redstone
Arsenal, AL 35898. Periodical postage is paid at the Huntsville, AL post office and at additional mailing offices.
Postmaster: Send address changes to PS, The Preventive Maintenance Monthly, USAMC LOGSA (AMXLS-GP), Bldg. 3303, Redstone
Arsenal, AL 35898.
ISSUE 739 JUNE 2014
TB 43-PS-739, The Preventive Maintenance Monthly, is an official publication
of the Department of the Army, providing information for all Soldiers assigned
to combat and combat support units and all Soldiers with unit maintenance
and supply duties. All information published has been reviewed and approved
by the agency responsible for the equipment, publication or policy discussed.
Application of the information is optional with the user. Masculine pronouns may
refer to both genders. The use of product or company names does not constitute
endorsement of those products, services or companies by the U.S. Army. The
use of non-DoD hyperlinks, along with their content, does not constitute
endorsement by DoD or DA. Neither DoD nor DA exercises any editorial control
over, and cannot vouch for, content on non-DoD websites.
739 00-01.indd 1-2 5/1/14 10:26 AM
Click here for a copy of this article to save or email.
3 PS 739 JUN 14
SYSTEM
ON
E
N
G
I
N
E
T
R
O
O
P
AFES - CEP
HISTORY
PANEL
FAULT
LED
CEP
S2
E2
E7
E8
S4
E3
S3
S7
S6
S5
E1
S1
RESET
TEST
M
A
N
U
A
L
D
I
S
C
H
A
R
G
E
After start up, only the green
POWER lamp should stay lit on
the detection system and engine
control box. No other lamps
should be lit.
4. Turn your Strykers main
power switch to ON and
check the AFES control panel.
When the vehicle is started,
all the LEDs on the AFES
panel will blink for up to
seven seconds.
5. Ensure pressure
gauges on the
extinguisher
bottles are in
the green zone.
Safety
Stryker
AFES PM
Means
Safety
For Crew
Crewmen, your
Strykers automatic fire
extinguishing system
(AFES) can save your life
in the event of a fire.
But just like any other
piece of equipment, regular
PMCS is critical in making
sure the AFES works when
you need it most.
Do these
checks every
day to keep
your AFES
good to go
Make sure sensors are
free of dirt and debris
1. Inside the crew
compartment, make
sure shipping caps
have been removed
and stowed in the
cap bag and replaced
with the AFES nozzle.
3. Check each wire connector on the
cylinder. All should be connected
and in good condition.
remember: AFES crew
compartment sensors
trigger the extinguisher
through optical flame
detection.
So never have an
open flame inside
of your Stryker or
hang items in front
of sensors.
OK, I give
up. What are
you doing?
and that includes fires!
itd be so
much simpler if
youd just do
some AFES PM!
I never go
on a mission
unless Im
prepared for
everything
2. Make sure all detector lenses are
clean. Wipe the dirty lenses with
a clean, dry cloth. A lens tissue
dampened with a mild cleanser
can also be used.
739 02-03.indd 1-2 4/21/14 3:03 PM
Click here for a copy of this article to save or email.
4 PS 739 JUN 14 5 PS 739 JUN 14
Crewmen, your Strykers run-fat tires allow you to get out of a dangerous situation
even when one or more of the tires have been seriously damaged.
But remember, your Strykers run-fat tires are only designed to get you out of the
danger zone. You need to slow down and drive just far enough to get to safety when
running on punctured or damaged tires.
Drive no further than 25 miles and no faster than 30 mph when on roads that
are in good condition. You might need to reduce speed and total mileage when
on really rough roads or terrain. Thats to prevent damaging the wheel rims and
suspension system.
Dont drive more than fve miles if
all of the vehicles tires are punctured
or damaged.
Driving too long on punctured or
damaged run-fats can cause tires to
catch fre. Keep an eye out for smoke
coming from the tires and signs of
tires shredding or breaking apart.
Pieces of tires breaking away from
the vehicle can damage fuel and
brake lines, increasing the likelihood
of a fre.
If possible, reduce the air pressure of the tires opposite the damaged tires. Thatll
improve your Stykers handling and control if the central tire infation system (CTIS)
isnt working.
Crewmen, its tempting to use your combat vehicles slat armor as extra storage space for
your gear and supplies.
But the slat armor, which is designed to deect an RPG blast before it can damage your
vehicle and hurt you and your fellow crewmen, wont be effective if items are placed in
front of or behind the armor.
Dont store cases of water bottles, water cans or other items between the slat armor
and the vehicle. And dont hang rucksacks, litters and other gear on the outside of the
slat armor. Litters should be secured to the outside of the vehicle with litter brackets, not
stored behind the slat armor or attached to it.
Never step or climb on the slat armor.
This can bend or break the slats. The space
between the slats is designed specically to
disrupt an RPG. Any change to that spacing
can leave you unprotected.
1. Look for cracked, warped or broken
slats. Report any you nd.
2. Tighten bolts and mounting
hardware as needed, and replace
anything thats missing.
3. Clear paper, leaves, branches and
other debris from the slats.
4. Look for rust and report any you nd.
Not
Run-Flat Tire Tips
Stryker
Run-Flat Tire Tips
T
H
U
M
P
A
!
T
H
U
M
P
A
!
T
H
U
M
P
A
!
T
H
U
M
P
A
!
TH
UMP
A
!
Combat Vehicles
Slat
Armor
Not For
Storage
Reduce speed and distance when driving on
a punctured or damaged run-at tire
I can count on
them to get me out
of here safely!
Sure glad I
have these run-
flat tires.
Dont hang items on the outside... ...or store them on the inside of slat armor
Also, a little PMCS goes a long way
toward making sure your vehicles slat armor
will keep you safe. Follow these tips
Where are
we gonna
store all
this gear?
Guess we
could just
pile it inside
the slat
armor.
Oh, no, you
dont! Thatll
make you and
me less safe
from RPGs!
T
H
U
M
P
A
!
T
H
U
M
P
A
!
739 04-05.indd 1-2 4/21/14 3:03 PM
Click here for a copy of this article to save or email.
Click here for a copy of this article to save or email.
6 PS 739 JUN 14
Crewmen, a mission requires a lot of gear. Just be sure to load all that gear on your
Stryker the right way so the missions success isnt jeopardized.
The best place to store
rucksacks and other gear is in
the bustle rack. Of course, the
bustle rack will only hold so
much. So your next storage
stop is the roof.
Just dont load items on the
roof of your Stryker in a way
that interferes with antennas,
hatches or the gunners feld
of view.
Use nets and
tiedown straps
to secure gear
to the roof, but
make sure the tie
downs are kept
away from door
hatches, hinges
and handles.
Dont stack equipment and
gear higher than the bottom
window of the objective gunner
protection kit (OGPK). That gives
the gunner a clear feld of fre.
If your Stryker has roof
storage boxes, put all the gear
and equipment you can inside the
boxes. Dont strap or tie anything
to the outside of the boxes.
Crewmen, its tempting to hang items
like helmets and other gear from the
turret safety screens in your tanks.
But that can cause some real problems.
The extra weight cracks and bends the
screens. The bent screens get hung up
on electrical cables and hydraulic lines
when the turret is traversed, causing some
serious damage.
That kinda headache you defnitely
dont need. So store your gear properly
and keep the screens from getting hung
up with damage.
R
o
f
S
t
o
r
a
g
e
D
o
n
e
R
i
g
h
t
Stryker
R
o
f
S
t
o
r
a
g
e
D
o
n
e
R
i
g
h
t
M1-Series Tanks
Dont Get Hung Up On
Screen Damage
Dont hang gear on safety screens
Gonna hang
this on your
turret safety
screen to
brighten up
the place.
Dont you know
thatll damage
my screens?
Besides,
I prefer
Picasso!
Use new external storage boxes if available, but dont tie or strap items to outside of boxes
Store personal gear in bustle rack
Secure gear to roof with nets and tie-down straps,
but dont interfere with hatches, antennas or
gunners eld of re
Good Grief! I cant
carry out a mission
with all that stuff
on my roOf!
739 06-07.indd 1-2 4/29/14 4:44 PM
Click here for a copy of these articles to save or email.
8 PS 739 JUN 14
An Exception to Every Rule
Theres a mount assembly, NSN 2350-
01-593-1101, that does allow you to mount
a roadwheel in front of the loaders hatch
on your M1.
The mount offsets the roadwheel from
the lifting bolt holes while allowing the
roadwheel to sit fush against the turret
roof. That relieves any strain and protects
the threads.
However, if your tank doesnt have the
mount assembly, dont use the extra bolts
on the top of the turret to mount a wheel
assembly or anything else.
Those extra bolts on the top of your tanks turret are there for
a reason. The bolts, NSN 5305-01-014-5124, protect the threads
inside each of the holes where the turret lifting device is attached.
If those threads get damaged, theres no way to separate the
turret from the hull for sustainment-level repairs.
Dont use mount assembly for anything
other than mounting road wheels
M1-Series
Tanks
No Extra Duty
For Turret Bolts
and three bolts back here protect
turret lifting device mounting holes
Eight bolts
here
Im gonna mount this to
your turret so we dont
miss the big gamE!
Hope youre
not planning to
use my turret
bolts. Those
are off limits!
I know this isnt as much
fun as watching the game,
but my turret bolts are
worth it!
Never use
the bolts for
mounting stuff like
flag brackets,
roadwheels, lights
or other items.
if youve removed any
of the bolts or some
are missing, check the
holes to make sure
theyre clean and
free of debris.
A little anti-seize
compound will prevent
corrosion and reduce wear
and tear on the threads.
You can
order it with
NSN 8030-00-
597-5367.
After youve added it to the threaded holes,
put a flat washer, NSN 5310-01-382-9030, on
each bolt and torque them to 50-75 lb-ft.
739 08-09.indd 1-2 4/29/14 4:44 PM
Click here for a copy of this article to save or email.
10 PS 739 JUN 14
One-piece Arctic (green) 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-459-0365
Three-piece Tan 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-539-3936
Three-piece Arctic (green) 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-539-3903
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-460-3487
2540-01-564-3669
2540-01-564-3372
4710-01-564-2565
4710-01-564-2778
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
24
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Assembly, pipe
Strap, tiedown
Snap, extension
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-460-3487
2540-01-466-1937
2540-01-466-1938
4710-01-461-9274
4710-01-461-9189
5340-01-461-1429
5340-01-451-8966
4710-01-393-3192
5340-01-460-6616
5325-01-460-7431
5340-01-436-7620
2540-01-461-0106
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-460-2337
2540-01-564-3669
2540-01-564-3372
4710-01-564-2565
4710-01-564-2778
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
FMTV
Cargo
Cover
Kit
News
You
Can
Use!
Most cargo cover
kits are being re-
designed from the
current three-piece
bow kit to a new one-
piece bow kit.
cover
up in the
cold!
Need to install
a new lightweight
cargo cover kit on
your units FMTVs?
For kits that are out of
stock, order the down parts
to piece the kit together.
Here are the three-piece and related
one-piece kit NSNs as well as the
NSNs for the kits components
The one-piece kits wont
be available until Sep 14.
in the meantime, keep
ordering the three-piece kits
until theyre gone.
739 10-11.indd 1-2 4/29/14 4:44 PM
Click here for a copy of this article to save or email.
12 PS 739 JUN 14 MORE
One-piece Tan 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-437-1463
One-piece Woodland Camo 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-385-9462
Three-piece Woodland Camo 2
1
/2-ton Cargo Cover Kit,
NSN 2540-01-539-3626
Three-piece Arctic (green) 5-ton Cargo Cover Kit,
NSN 2540-01-539-3915
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-460-2337
2540-01-466-1937
2540-01-466-1938
4710-01-461-9274
4710-01-461-9189
5340-01-461-1429
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-461-0106
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-387-3987
2540-01-466-1937
2540-01-466-1938
4710-01-461-9274
4710-01-461-9189
5340-01-461-1429
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-461-0106
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, Support
2540-01-387-3987
2540-01-564-3669
2540-01-564-3372
4710-01-564-2565
4710-01-564-2778
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-460-0898
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
cover
up while
driving
in the
wOods!
739 12-13.indd 1-2 4/29/14 4:44 PM
14 PS 739 JUN 14 MORE
One-piece Arctic (green) 5-ton Cargo Cover Kit,
NSN 2540-01-459-6479
One-piece Tan 5-ton Cargo Cover Kit,
NSN 2540-01-436-9658
Three-piece Tan 5-ton Cargo Cover Kit,
NSN 2540-01-539-3946
Three-piece Woodland Camo 5-ton Cargo Cover Kit,
NSN 2540-01-539-3647
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-460-0898
2540-01-466-1937
2540-01-466-1938
4710-01-460-9522
4710-01-461-9274
5340-01-461-1429
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
2540-01 461-0106
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-460-1075
2540-01-466-1937
2540-01-466-1938
4710-01-460-9522
4710-01-461-9274
5340-01-461-1429
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
2540-01 461-0106
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-460-1075
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
Description
NSN
Qty
1
1
2
5
5
24
1
3
6
1
26
4
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-472-5091
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-461-1429
739 14-15.indd 1-2 4/21/14 3:04 PM
16 PS 739 JUN 14
Description
NSN
Qty
1
2
1
5
5
2
1
1
3
24
6
4
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Snap extension
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-472-5091
2540-01-466-1937
2540-01-466-1938
4710-01-460-9522
4710-01-461-9274
5340-01-461-1429
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5325-01-460-7431
5340-01-436-7620
5340-01-461-0106
Description
NSN
Qty
1
2
2
5
5
5
2
36
1
1
3
8
6
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Snap extension
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-460-0428
2540-01-466-1937
2540-01-466-1938
4710-01-461-9189
4710-01-460-9522
4710-01-461-9274
5340-01-462-8578
5325-01-460-7431
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
2540-01-461-0106
Description
NSN
Qty
1
2
2
5
5
5
36
1
3
8
1
38
6
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-460-0428
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2565
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
2540-01-464-0106
5340-01-462-8578
Description
NSN
Qty
1
2
2
5
5
5
36
1
3
8
1
38
6
2
2540-01-393-0950
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2565
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-451-8966
5325-01-569-5453
2540-01-464-0106
5340-01-462-8578
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
Three-piece
Camo 5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-539-3927
One-piece Woodland Camo 5-ton Cargo Cover Kit,
NSN 2540-01-386-2952
One-piece
Arctic (green)
5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-464-1399
Three-piece
Arctic (green)
5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-539-3909
cover
up while
driving in
the sun!
739 16-17.indd 1-2 5/2/14 11:24 AM
18 PS 739 JUN 14 MORE
Description
NSN
Qty
1
2
2
5
5
5
2
1
1
3
8
6
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-393-0950
2540-01-466-1937
2540-01-466-1938
4710-01-461-9189
4710-01-460-9522
4710-01-461-9274
5340-01-462-8578
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
2540-01-461-0106
Description
NSN
Qty
1
2
2
5
5
5
2
1
1
3
8
6
Cover assembly
Bow, front or rear
Bow, center
Tube, horizontal
(1-in dia, 72
1
/5-in length)
Tube, horizontal
(1
1
/3-in dia, 93-in length)
Tube, horizontal
(1-in dia, 76
1
/5-in length)
Strap, support
Strap
(1-in width, 24-in length)
Pipe, assembly
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Brace, bow support
2540-01-479-5022
2540-01-466-1937
2540-01-466-1938
4710-01-461-9189
4710-01-460-9522
4710-01-461-9274
5340-01-462-8578
5340-01-451-8966
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
2540-01-461-0106
Description
NSN
Qty
1
2
2
5
5
5
36
1
3
8
1
38
6
2
Cover assembly
Bow, center
Bow, front or rear
Tube, horizontal
(1
1
/4-in dia, 76
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 72
1
/4-in length)
Tube, horizontal
(1
1
/4-in dia, 93
1
/4-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
Brace, bow support
Strap, support
2540-01-479-5022
2540-01-564-3669
2540-01-564-3372
4710-01-564-2778
4710-01-564-2565
4710-01-564-2798
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-451-8966
5325-01-569-5453
2540-01-461-0106
5340-01-462-8578
Description
NSN
Qty
1
1
1
1
5
5
5
24
1
3
6
1
26
Cover assembly
Bow, front
Bow, center
Bow, rear
Tube, horizontal
(1
1
/4-in dia, 51
3
/5-in length)
Tube, horizontal
(1-in dia, 51
5
/8-in length)
Tube, horizontal
(1
3
/40-in dia, 74
1
/2-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
2540-01-479-5026
2540-01-564-3372
2540-01-564-3669
2540-01-564-4936
4710-01-565-1202
4710-01-564-9737
4710-01-573-0305
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7619
5340-01-451-8966
5325-01-569-5453
One-piece Camo
5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-387-5734
One-piece Tan
5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-436-8898
Three-piece Tan
5-ton (LWB)
Cargo Cover Kit,
NSN 2540-01-539-3588
Tan
5-ton (Dump)
Cargo Cover Kit,
NSN 2540-01-539-3638
NOTE: The 5-ton dump truck covers have not been changed to a one-piece conguration.
Here are the down parts for the three-piece cargo cover kits:
were
almost
done!
739 18-19.indd 1-2 4/21/14 3:04 PM
20 PS 739 21 PS 739 JUN 14
dont throw CAUTION to the wind when its time to hook up a trailers brake air
hoses to your 2
1
/2- or 5-ton truck. Cross those air lines and the trailer brakes will lock
up, burn out or ruin the tires!
So make sure your trailers hooked up right. Its not that hard. Just locate the
SERVICE and EMERGENCY air couplings and use the TM to verify which is which
on your trailer.
If theyre not already marked, its a good idea to color-code the trailer air hose
connectors and the trucks gladhand couplings now. A dab of blue paint on the
SERVICE connectors and red on the EMERGENCY pair will keep things straight
the next time you hook em up.
2
1
/2-ton truck
NSN 9905-
ID Plate
SERVICE
EMERGENCY
00-740-9721
00-774-4284
5-ton truck
NSN 9905-
00-999-7370
00-999-7369
Trailer Hookups
You can also
add a SERViCE
or EMerGENCY
ID plate to
your trucks
gladHands
with these
NSNs
Color code truck gladhands and trailer couplings
Description
NSN
Qty
1
1
1
1
5
5
5
24
1
3
6
1
26
Cover assembly
Bow, front
Bow, center
Bow, rear
Tube, horizontal
(1
1
/4-in dia, 51
3
/5-in length)
Tube, horizontal
(1-in dia, 51
5
/8-in length)
Tube, horizontal
(1
3
/40-in dia, 74
1
/2-in length)
Snap, extension
Pipe, black iron
Strap, tiedown
Strap
(1-in width, 27
9
/16-in length)
Strap
(1-in width, 24-in length)
Snap button
2540-01-472-4368
2540-01-564-3372
2540-01-564-3669
2540-01-564-4936
4710-01-565-1202
4710-01-564-9737
4710-01-573-0305
5325-01-460-7431
4710-01-391-3192
5340-01-460-6616
5340-01-436-7620
5340-01-451-8966
5325-01-569-5453
Woodland Camo 5-ton (Dump) Cargo Cover Kit,
NSN 2540-01-539-3631
Color-
coding
Saves
Brakes!
OucH! oh,
my achin
tread!
what
HapPened?!
LoOks like
you crOsSed
the Air
BrakE lines.
Well, I think
weve got all
these trucks
covered!
you
said it,
connie!
739 20-21.indd 1-2 4/29/14 4:42 PM
Click here for a copy of this article to save or email.
22 PS 739 JUN 14 23 PS 739 JUN 14
Mechanics, the M230 gun requires total tear down for inspection, cleaning, and repair
during the 500-hour annual inspection or after 5,000 rounds of ring.
The key to preventing malfunctions in your area weapon system is to make sure all gun
parts are reinstalled correctly.
For example, part of the procedure requires removal and installation of the worm gear
components. Some mechanics try to install the worm gear by stacking the pieces on top of
the bearing retainer. Then they install the whole stack into the opening on the receiver and
use a hammer to tap in the worm gear. Dont try this! You can bet your bottom dollar it
wont work and will just result in broken parts.
When installing the worm gear, make sure its teeth mate up with the teeth on the
vertical drive shaft. Instead of guring out a quick way to put the gun together and possibly
damaging parts, follow the installation procedures and install the worm gear piece by piece
like it says in IETM 0126 for the LONGBOW APACHE.
If the extractor is not completely down, it cant grab the rounds to place them in
the bolt face. When the breech bolt is moved, the gun will jam with the bolt to the
rear. Then you cant close the gun door because the bolt is stuck. The only way to fx
a jammed gun is to call the armament folks to the rescue.
Another thing that could knock your gun out of commission is not doing pre-load
gun inspections to make sure the spring pin is installed in the extractor body.
During cleaning and servicing, the gun is taken apart. When the gun is reassembled,
the spring pin sometimes gets overlooked and isnt reinstalled.
Thats bad news for the gun. If its fred without the spring pin, the gun will
malfunction. The fring pin sticks, which can lead to run-away fring. And that will
destroy the breech bolt.
Prepare M3P Gun For Firing
M230
Gun
Take No Short Cuts
On Gun Maintenance
OH-58D
Prepare M3P Gun For Firing
Stacking
worm
gear
parts on
bearing
retainer
like
this
to install in receiver opening will not work
Gunners, keep your M3P .50 cal
machine gun, NSN 1005-01-303-5250,
off the NMC list with preventive
maintenance and attention
to detail.
Before telling the pilot to move the
guns breech bolt forward or to the
rear during gunnery exercises, make
sure the extracTor is completely
down and seated in the gun.
uHh... After the
inspection, I tried
to speed up the
assembly process.
No! Dont
tell me you
tried to stack
the worm
gear parts.
my insides
feel All
QuirkY.
Hey, I had to come
back because I couldnt
fire! The gun is jammed!
looks like
the culprit is
the extracTor.
someone didnt
pay attention
to detail!
Make sure extractor
is completely seated
739 22-23.indd 1-2 4/21/14 3:05 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
24 PS 739 JUN 14 25 PS 739 JUN 14
Crews, not servicing the turret on your Kiowa Warriors mast-mounted sight (MMS)
can lead to problems.
When servicing the MMS, take your readings with the MMS in the OFF position.
If the coolant level indicator reads between +60C and ambient minus 10C, no
servicing is required, like it says in Para 8-16 (9) of TM 1-1520-248-10. When
adding coolant, follow the info in EM 0246, WP 2875 00.
After youve added coolant, check the sight
glass again to make sure the temperature
reading is normal. If the reading is between
60C and the ambient temperature minus
10C, no service is required. The color should
be yellow or white, with white being the most
common ambient temperature. The level
should not be in red. Red is -120C all the way
to 0C. Thats not good. If the reading is above
60C, you need to drain the excess coolant
from the system.
Never overfll the MMS with antifreeze. Too much coolant overpressurizes the
system. That can cause coolant lines to burst inside the MMS.
Over time, additives in the antifreeze can form gummy deposits and block coolant
circulation, causing the turret to overheat. If that happens, its probably time for a
coolant change.
Remember, there is a 300-hour inspection requirement to drain, fush and refll the
system with fresh coolant. Follow the procedures in EM 0246, WP 2878 00.
Sometimes the simplest maintenance task on your Kiowa Warrior can turn into a lot
more than you bargained for.
For instance, rotating or folding rotor blades should be a no-brainer, right? But
when you use the tie-down wand assembly, NSN 1730-01-185-8877, things can get a
little slippery.
The wand assembly is placed under the blade to lift it. While rotating or folding,
the blade can slip off the top of the wand even if youre moving very slowly. If that
happens, the blade drops from an elevated position damaging the blade cuff, the hub
and the root of the blade.
To keep the blade from slipping off the wand, wrap some duct tape around the
wand to create a top. Then add another piece of the tape to cover the exposed sticky
side so it doesnt come in contact with the painted surface of the blade. Duct tape is the
simplest method but another option is to use some strap webbing.
Then you can easily slide the wand onto the blade. The tape over the top and sides
keeps the blade from sliding off.
Make a note that the wand assembly is a part of the Kiowa Warriors fy away items.
OH-58D
Servicing the
Mast-Mounted Sight
OH-58D
Keep Blades
Off
S
l
ippery
S
l
ope
Always check temperature
tape before ight
Wand assembly with
no top slips off blade
Wrapping duct tape to
create top prevents slips
OK, Im tired
of this tool
slipping!
boy,
does my
MMS need
some
juice!
dont you
worry. Ive
got you
hooked up
with the
coolant
you need!
739 24-25.indd 1-2 4/21/14 3:05 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
26 PS 739 JUN 14 27 PS 739 JUN 14
Mechanics, the Kiowa Warriors weapons system cables and connectors are made
for a snug ft. If you force a ft, youll force a break.
Before hooking cables into
aircraft weapons system connectors,
visually check the cable pins and
the connector receptacles. Make
sure you have a match before you
hook up.
If your aircraft has been through
Reset, it is especially important
to check connectors. What may
have matched up fne before may
not now.
If you force a mismatched cable and connector together, youll bend or break
the cables pins when you try to muscle it in place. These internal pins are easily
damaged, so the armament folks will have to take apart the cable to repair it or
replace the entire cable, depending on the type of damage.
So avoid the agony of defeat by making sure you have the right match frst. Then
go easy when hooking up the Hellfre missile system, the M3P machine gun or rocket
launcher to your aircraft.
inspect Cables
Before Hookup
OH-58D
inspect Cables
Before Hookup
Ensure connector and connector receptacle
match before hooking up weapon system
Make sure youve
got a match before
hooking me up
to that weapons
system!
The Planet
of Atmos
where the principles
of pM reign supreme!
From a distance, all
looks peaceful
but lets take
a closer loOk this trial is
a mockery!
a Mockery,
I tell You!
The Battle for PM
739 26-27.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
29 PS 739 JUN 14
In the Hall of
Justice, supervillain
Dr. Void and his
gang stand trial...
no cause for
questioning my
experiments with
inactive preventive
maintenance.
you
have no
cause!
People with super
powers have no
need of PM!
S
i
l
e
n
c
e!
Eagle Master,
Onyx, please read
the charges.
Dr. Void and
his gang stand
accused of
attempting to
deactivate and
reprogram the
PM systems of
Atmos.
Had Eagle
Master and I not
stopped dr. Void,
Atmos would have
been left totally
unprotected.
Dr. Void,
How do you
plead?
Very well,
since you
do not deny
your crimes,
I sentence
you and your
gang to
incarceration
on the prison
satellite of
Outermost!
Onyx, please
carry out the
sentence.
I did
nothing
wrong!
b
an
g!
ba
n
g
!
739 28-29.indd 1-2 4/30/14 11:20 AM
30 PS 739 JUN 14
beEp
beEp
beEp
beEp
We all have super
powers and they
dont seem to
be at risk. Our
embedded weapons
regenerate and
modulate with our
internal biology.
its my
pleasure,
your
honor.
But we must do PM on all the
planetary defense systems!
The Code of PM requires it!
A few hours
later, the
Council of
Justice
meets
What do you
think, Mace?
No!
Nooooo!
Youll pay
for this
I understand your
concern, Eagle Master.
But with Dr. Void and his
gang imprisoned, Im not
sure its necessary.
But that doesnt mean
we should never do PM.
My scans of the planets
shield generators
indicate a slight drop in
their deflection capacity.
PM could improve
I
agrEe.
Huh? Sorry. Im
calculating the
decimal ratio of pi.
Ask Dr. Sphinx.
Shes the planets
maintenance czar.
Weve never lost
a battle against a
supervillain. Our
maintenance codes are
self-perpetuating!
At least well be
ready if something
should go wrong.
I was afraid
of this.
it appears
Dr. Void has
escaped!
Some time later, the headquarters of Eagle master
and Onyx
The
defense
systems will
continue as usual with no
remodulation shutdowns.
PM can wait until theres
an actual problem!
Our
planetary
defense
systems have
failed!
Dr. Void must have
used the prison
as a testing
ground for his
experiments!
Im sure hell
want to exact
his revenge
on the Council
of Justice!
beEp
beEp
beEp
beEp
Captain Wisdom,
whats your opinion?
Based on the judges
decision, we cant do
PM on the planetary
defenses.
But we can
maintain our
own systems
and weapons.
Thats the
planetary
defense warning.
Better use your
super vision,
Eagle Master.
739 30-31.indd 1-2 4/29/14 4:44 PM
33 PS 739 JUN 14
I said tie them all
up, you fools!
Inside
the council
chambers
Dont worry
about him, Doc.
Hes stuck on
some kinda math
problem.
point 14159
265359141
On the count of three,
Ill blast the door
with My psychic rays!
One...
two...
When you decided not
to do PM, I knew your
planetary defense
systems would fail.
And now everyones
super powers are
diminished as well!
No one can stop us!
Let him
go, you
fiend!
Youre
too late!
t
h
r
e
e!
Dont be so sure,
Dr. Void. We believe
in PM. Our super
powers are as
strong as ever!
you have it
backWards,
Dr. Void!
aLlow me to
Demonstrate!
death TO
Preventive
MaintenANcE!
you A-Void
preventive
maintenance
so you
are de-VoiD
of victory!
get it?
A-VOid
De-Void
Dr. Void
{grOaN!}
I think it
was your
Corny
Joke that
knocked
him out,
eagle
master!
739 32-33.indd 1-2 4/29/14 4:43 PM
35 PS 739 JUN 14
Remember the keypad gets hot. If you hold the bottom of it with your bare hands,
you can burn yourself. Wear gloves when you hold the keypad.
Make sure the SSS is securely strapped down for travel. If the SSS bounces around
during travel, it loses its position and then its doing you no good. It can take up to 10
minutes to strap down the SSS properly. Feel it for looseness before you hit the road.
Get extra straps if necessary. Some units fnd the straps that come with the SSS
arent enough to securely hold the SSS in place. Order more straps with NSN 3990-01-
587-1792.
SSS
Problems
Simplifed
Patriot Missile System
SSS
Problems
Simplifed
if you
remember a few
simple tips
The Patriots simplified survey
system (SSS) simply does a great
job telling you where you are
The only NSN for the
paper used with the sSs is
NSN 7350-01-586-0116.
because that brings 100
rolls, you may want to get
the paper from your local
contractor if possible.
I should have listened to you
two. We were totally helpless.
I shudder to think
what might have
happened without
your dedication to
the Code of PM!
PM must
always remain
of primary
importance
for Atmos.
Well, I guess
wed better get
these villains back
behind bars. Captain
Wisdom, how about
a little help? Uh,
Captain?
point
1415926
53591
4159
Thats right,
Eagle Master.
I think all the
inhabitants
of Atmos
have learned
a valuable
lesson today.
739 34-35.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email.
37 PS 739 JUN 14
M240H Bipod
TM Changes for M240H and M240L
Get out
your pencils,
small arms
repairmen. You
need to make
some changes
to the M240
machine guns
TM 9-0115-313-
23&P.
On WP 0017 01,
pencil in that the
safety spring,
NSN 5340-01-
550-1620, must
be replaced
whenever its
removed.
it should not be
removed unless
absolutely
necessary.
MWO 9-1005-313-23-1 up-
graded the M240Hs bipod as-
sembly. The worK should have
been completed by 13 Nov 13.
As a result of the
MWO, Fig 19 in WP
0049 00 needs to be
changed to this
NSN Nomenclature
Item
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Yoke, bipod
Leg, left assembly
Leg, upper left
Leg, lower left
Leg, right assembly
Leg, lower right
Latch
Setscrew
Spring, helical comp
Leg, upper right
Leg assembly
Plunger, detent
Spring, helical comp
Pin, spring
Cap, detent
Screw, shoulder
Nut, self-locking
1005-01-522-0761
1005-01-522-0764
1005-01-522-0767
1005-01-522-0762
5305-01-524-2975
5360-01-522-0763
1005-01-522-0769
5340-01-522-0765
5360-01-522-0766
5315-01-114-2396
1005-01-522-0768
5305-01-563-5472
5305-00-245-8825
SMR
Code
XAFZZ*
PAFFF
PAFFF
XAFZZ*
PAFFF
XAFZZ*
PAFZZ
PAFZZ
PAFZZ
PAFFF
XAFZZ*
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
*Do not order XA coded items. Order the next higher assembly.
M240L Safety Spring
where
are you
going?
thats a
lot of
changes.
I need
another
pencil!
16
15
13
14
11
12
10
9
6
8
5
7
17
3
2
4
1
739 36-37.indd 1-2 4/21/14 3:06 PM
Click here for a copy of this article to save or email.
38 PS 739 JUN 14 39 PS 739 JUN 14
Dear Half-Mast,
The dust covers for the day sights on our M110 semi-automatic sniper
system (SASS) disappear. Can we order replacement covers?
SGT D.R.
Dear Sergeant D.R.,
Yes! Order the front dust cover with NSN 1005-01-544-7450 and the rear one
with NSN 1005-01-545-0711. They arent listed in TM 9-1005-342-23&P.
NSN Item
.300 Magazine
Hard case
Sling
Suppressor
Suppressor sleeve
Scope case
Scope
Deployment kit
Soft case
LFU/ARD
Cleaning kit
Magazine
Recoil pad 1.5 inch
Recoil pad .75 inch
1005-01-588-2913
1005-01-604-1567
1005-01-603-3480
1005-01-604-1555
1005-01-604-1556
1005-01-603-3478
1240-01-603-2241
1005-01-604-1545
1005-01-604-1569
1240-01-502-1295
1005-01-604-1528
1005-01-606-7255
1005-01-604-1503
1005-01-604-1502
Part
Number
130340406
404067
404059
405322
404062
40465
40457
404049
40468
13001589
404040
302176
303300
303299
Dust Cover ReplAcements?
Whats Needed to
Turn in M2010
M110 SASS
Dust Cover ReplAcements?
Rear and front dust covers are available
Dear Half-Mast,
Most of the TMs
for small arms show
screws safety-wired
with several loops.
But we often receive
weapons from the
manufacturer or
depot with screws
safety-wired with
only one loop. Are
both methods OK?
D.L.
Dear Mr. D.L.,
Both methods are
fne. The important
thing is that the screws
are in fact safety-wired.
Otherwise, vibration
during fring works them
loose. Then youve got
real problems.
How Should
Safety Wire
Be Wired?
Single-strand or double-
twist safety wire OK
Small Arms
When its time to turn in your
M2010 sniper rifle, you must turn
in everything, not just the rifle.
if any of the following are missing,
a Financial Liability Investigation of
Property Loss (FLIPL) will be initiated
waitaminit! wheres the
rest of my stuff? My
case? My magazines?!
Im not ready
for turn-in!
ah, now
this is
a gooD
question!
There may be other items
in the deployment and
cleaning kits that may
also need to be turned in.
See your hand receipt.
Remember, too, the M2010
must be in its original
configuration for turn-in.
if you have any questions, contact TACOMs Gene Meade at DSN 786-1253,
(586) 282-1253, or email: [email protected]
739 38-39.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email. Click here for a copy of these articles to save or email.
40 PS 739 JUN 14 41 PS 739 JUN 14
Dear Half-Mast,
We have several different models of the MK 19 in our unit and were not
sure how to list them on our property books. Can you help?
SSG S.L.
MK 19 MOD 3, NSN 1010-01-126-9063, is the basic model
MK 19 MOD 3 with an adjustable sight bracket resulted from
MWO 9-1010230-50-1. Its NSN is 1010-01-490-9697. The
sight bracket was added to the right side of the receiver.
MK 19 MOD 4, NSN 1010-01-362-6513, was added to the
Army inventory in 2013. Its used with the armored security
vehicle (ASV). Unit MTOEs have probably not been updated
to include the MOD 4. Property book ofcers are authorized
to add the MOD 4. The MOD 4s data plate and item unique
identication (IUID) will be updated when the MK 19 is sent
for overhaul. The MOD 4 does not have its own TM yet.
Order spare parts for it through DLA. They are listed in TM
9-1010-230-23&P.
Dear Editor,
As a TACOM LAR, Ive run into several instances where an M16A1 front
sight post was installed on an M16A2 rifle.
The sight posts are different and the
difference makes a difference. The A1 post is
round, whereas the A2 post is square. The A1
post has five adjustment notches, whereas the
A2 has four. You can sight with an A1 post on
an A2 rifle, but you wont be able to use the
corrections when zeroing a target.
All Soldiers should check their M16A2s
and make sure they have a sight post that
is square. If you have the wrong sight post,
get your repairman to install the correct one,
NSN 1005-01-134-3625.
Karl Hayhurst
TACOM LAR
Camp Casey, South Korea
Editors note: Another fne tip, Karl. Thanks for sharing it. Soldiers,
the round sight post is obsolete for all weapons. So if your M16A1 still
has the round sight post, get it replaced with the square M16A2 post.
What Are
MK 19 Model
Differences?
M16-Series Rie
Dont Lose Sight Of
Correct Sight
Tip of
M16A2
sight post
should be
square
hey! wait a
minute! this
sight post
is round.
mine is
sposed to
be square!
what gives?!
Sure thing.
Heres the
lowdown
if youre unsure which MK 19
you have, contact your local
TACOM LAR.
Or you can contact TACOMs
Wayne Waroway at DSN 786-
1254, (586) 282-1254, or email:
[email protected]
Now, who
am I?
if they
Only knew!
I think
I can
help
with
that.
739 40-41.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
43 PS 739 JUN 14
Generator
Solutions
Right
Here!
Get New Insulation
The old insulation breaks off and gets sucked into the air cleaner. That cuts off the
generators airfow. Since 2011, new BIDS have insulation with a special coating that
wont come apart.
If your BIDS doesnt
have the new insulation, see
maintenance advisory message
(MAM) JPM-BD 11-01,
which explains how to get a
replacement set. One free set of
insulation may be available per
system. Additional sets have to
be purchased directly from the
manufacturer. Units install the
insulation. Instructions come
with the insulation.
For help getting the insulation or MAM, contact George Barnes at DSN 786-1387,
(586) 282-1387, or email: [email protected]
Pull Out Part of Exhaust Hose Before
Sliding Out Generator
Keep an Eye on Exhaust Pipes Wrapping
The generators vibration can
cause the wrapping to unravel to the
point it catches in the generator fan.
Help keep the wrapping on the
exhaust pipe with a 2-in hose clamp,
NSN 4730-01-515-4940.
Help extend the life of the exhaust
pipe by installing a 1
1
/2 x 1
1
/2 x 2
3
/4-
in slotted angle support bracket and a
1
3
/4-in muffer clamp, NSN 5340-01-
455-3934. The bracket, which was
suggested by the 326th Chemical
Company in Huntsville, AL, cuts
down on tension and vibration that
can damage the muffer tail pipe.
Get the bracket by contacting
George Barnes.
If you have a tailpipe break,
the 375th Chemical Company in
Council Bluffs, IA, suggests having
your maintenance section weld a
piece of pipe to the muffer and
exhaust pipe. That may be enough
to keep you operating until you get a
new muffer and tailpipe.
Generator
Solutions
Right
Here!
JBPDS BIDS
if the generator for the
JBPDS (joint biological point
detection system) BIDS cant
generate power, your BIDS is
powerless to detect threats.
Here are
a few ways
to keep the
generator
empowered
I hear Theres
new inSulATion for
my generator that
doesnt break apart!
how bout
gettin me
some?
Ill get
right On
it!
Pull out
3-4 feet of
the exhaust
hose to
give the
hose some
slack.
if you
dont, the
hoses
coupling
may tear
the hose
when
you pull
out the
generator
tray.
Pull out
exhaust
hose before
sliding out
generator
Im runnin lOw on
poWer heRE, you guys.
How about generating some generator
PM so I can really crank intO actioN?
Secure wrapping
with hose clamp
Bracket extends life
of exhaust pipe
739 42-43.indd 1-2 5/2/14 11:24 AM
Click here for a copy of this article to save or email.
44 PS 739 JUN 14 45 PS 739 JUN 14
Before
you
shoot:
When its time to use your common remotely operated weapons
station (CROWS) II, its important to frst unlock all the locks. If
CROWS is locked when you power it up, major damage to the main
frame assembly can result. That can cost more than $40,000 to fx!
Disengage the azimuth (AZ)
lock
Clean Back of Radiator Every Six Months
This is critical if youre operating in a sandy environment. Oil and sand collect on
the backside of the radiator. If it gets too dirty, the radiator cant cool the generator
and it overheats. That can kill the generator.
To clean the back of the radiator,
youll need to get your mechanic
to remove the fan guard, which is
held in place by several screws.
Spray low-pressure water through
the front of the radiator to loosen
up the gunk. Then use something
soft and fexible like a playing
card to scrape off the gunk. Dont
use anything metallic that could
damage the radiator coils.
Put the ELEVATION (EL)
transport lock in OPERATION
Remove the SSA clamp assembly and stow it in the
support equipment bag
powering
up!
if the M240-series machine gun op rod gas piston
pin loosens too much, your gun will stop firing.
Operators should immediately
check all their M240 op rods
for loose pins. Just feel the gas
piston to see if its loose. its OK
for it to move a little.
Also check
for any
damaged or
missing op
rod parts.
M240-Series
Machine Gun
LOOK FOR L
O
O
S
E
OP ROD PIN
M153 CROWS II
This check will be added to
the PMCS in the next update
to TM 9-1005-313-23&P.
There is no fix for a loose
piston pin other than to
replace the op rod.
Run low-pressure water through front
of radiator to knock loose crud
Of course, when
youre done with your
mission, you need to
relock CROWS.
Holey
moley!
you forgot
to unlock
me.
I think you
just did
in my main
frame.
UnlOCK
before
powering
up!
739 44-45.indd 1-2 5/2/14 3:47 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
46 PS 739 JUN 14
Place Your BETSS on
Preventive Maintenance
NSN 6115- Generator
5-kW MEP-802A
tactical quiet
generator (TQG)
5-kW MEP-812A TQG
3-kW MEP-831A TQG
3-kW MEP-832A TQG
01-274-7387
01-274-7391
01-285-3012
01-287-2431
TM
TM 9-6115-641-10 (Oct 09) and
TM 9-6115-641-24 (Apr 12)
TM 9-6115-641-10 (Oct 09) and
TM 9-6115-641-24 (Apr 12)
TM 9-6115-639-13&P (Apr 10)
TM 9-6115-639-13&P (Apr 10)
Work Package TM
TM 9-6115-641-10
TM 9-6115-641-24
TM 9-6115-639-13&P
WP 0010 & WP 0011
WP 0007 & WP 0008
Operator PMCS in WP 0009 & WP 0010.
Field Maintenance PMCS in WP 0015 & WP 0016
if you have a base
expeditionary targeting and
surveillance system-combined
(BETSS-C), listen carefully.
The BETSS-C
is powered by
one of these
generators
Heres where to
look in the TMs
for PMCS work
packages
And heres a
closer look
at some
common
maintenance
problems
and their
solutions
ENGINE OIL: When the engine is low on oil, parts can seize and the engine can
fail. Low oil pressure can cause cylinders to dry out and throw rods. Too much oil
creates pressure that can blow O-rings and the gasket to the valve cover. And that can
break the seals in the engine block.
Heres how to make sure the engine has the right amount of oil:
Operator PMCS
WARNING
Never service or perform
maintenance on a generator
while the engine is running.
Shut down the generator
and let the engine cool
before servicing.
Inspect the TQG for oil leaks before, during and after operating it. Report Class III
leaks to eld maintenance.
Remove the oil ll cap and look at the dipstick. Make sure the oil level is at the
FULL mark or between the hash marks. When the TQGs running, keep an eye
on the OIL PRESSURE indicator on the control panel or the LOW OIL PRESSURE
fault indicator.
Add oil to the engine crankcase if its low or if the indicators show the pressure is
low. Shut down the generator set before checking the oil level or adding oil.
Thats exactly whats happening. Recently, some
TQGs powering the BETSS-C stopped running
because Soldiers neglected preventive maintenance
checks and services (PMCS). In some cases, the
failed generator or its parts were beyond repair.
If the TQG goes down, the BETSS-C has no electrical power. Security monitoring
and surveillance suffer. Youve lost your eyes and ears.
Check OIL
PRESSURE
indicator
or LOW OIL PRESSURE fault indicator
Are
you
in?
Im
bettin
it all
on PM!
739 46-47.indd 1-2 5/2/14 11:10 AM
Click here for a copy of this article to save or email.
48 PS 739 JUN 14
FUEL: Fuel leaks are dangerous. Inspect the TQG for leaks before, during
and after operating it. If you fnd any, shut down the TQG and report the problem to
feld maintenance.
Dirt and debris in the fuel system make the engine run rough. They can cause
engine speed to vary. And that can spike voltage and damage equipment powered by
the TQG. Remove the fuel tank fll cap. Remove the mesh fuel strainer and wipe it
clean. Also inspect your plastic fuel cans. Make sure the caps are screwed on snug.
Covering the cans with a tarp helps keep dirt, debris and water out of the fuel, too.
The fuel/water separator removes water and sediment from the fuel. Open the
drain cock and drain the contaminants into a container. Inspect the fuel/water separator
for leaks, cracks and loose fuel lines before and after running the TQG. If you fnd any
damage, report it to feld level maintenance.
When the TQGs running, keep an eye on the FUEL LEVEL indicator on the
control panel and the NO FUEL fault indicator. Never allow the fuel tank to run dry
while the TQG is running. That can drain the batteries and damage the fuel pump.
Depending on which TQG you have, its fuel tank holds 4 or 5 gallons, enough for
about 8 hours of operation.
Refuel if the indicators show the fuel level is low. Shut down the generator
set before refueling. Never refuel while the engine is running. Read your TMs
WARNINGS about flling the fuel tank.
HEAT: A running engine creates heat. This heat needs to be released into the
surrounding air to reduce engine temperature. Problem is, heat releases more slowly in
hot weather than in cooler weather. That means engine temperature stays high longer.
The result: The engine overheats and may stop running altogether. During hot weather,
take precautions to avoid engine overheating.
If you put the TQG in a
revetment, give it plenty of
air. Center the TQG with at
least 4 feet between it and
the walls.
Another way to keep the
TQG cooler is to put it under
a solar shade. Solar shades
block out the sun and reduce
hot surface temperatures.
Heat and the 3-kW TQG
Before you run the 3-kW TQG,
inspect the air intake ducts, exhaust
ducts and air flter for clogging dirt
and debris. A clogged air intake or
flter chokes off air to the engine,
making it work harder. The results
are overheating and shutdown.
Remove clogs from the ducts.
Clean the flter with compressed air.
Replace it if necessary.
Keep the access doors closed. That allows air to fow around inside and cool the
generator. Closed doors also keep dirt and sand away from the engine.
Keep an eye on the ENGINE HIGH TEMP fault indicator on the control panel.
If the indicator shows the engines running hot, the problem could be a clogged air
flter or air intake ducts. Or the generator could be overloaded.
Read the operators troubleshooting table for instructions.
Each system includes
cover, poles, stakes and
repair kit.
Size
in feet
System
Type I
Type II
35 x 35
50 x 50
Floor area in
square feet
892
2000
NSN
5410-
01-519-7041
01-519-7185
System
Desert radar scattering
Desert radar transparent
Woodland radar scattering
Woodland radar transparent
NSN 1080-
01-475-0696
01-475-0694
01-457-2956
01-475-0697
The shades
come in two
sizes:
Wipe fuel
strainer clean
Keep an eye on FUEL LEVEL indicator and NO FUEL fault indicator
Tighten
fuel can
caps
Give TQG lots of room for air
Remove
clogging
dirt and
debris
from
ducts
You can also
shade the
generator with the
ultra-lightweight
camouflage net
system (ULCANS).
ULCANS is available
in four systems
739 48-49.indd 1-2 4/21/14 3:07 PM
50 PS 739 JUN 14
Heat and the 5-kW TQG
Also inspect the air intake ducts, exhaust ducts and air cleaner for dirt and debris.
A clogged air intake or cleaner chokes off air to the engine, making it work harder.
The results are overheating and shutdown. Remove clogs from the ducts. Check the air
cleaners restriction indicator. If its in the red, the air cleaner element is clogged. Clean
the element with compressed air. Replace it if necessary. Inspect the air cannister. If it
has dirt and debris, clean it with a lint-free cloth.
Keep the access doors closed so air
can fow around inside and cool the
generator. Closed doors also keep dirt
and sand away from the engine.
Now and then look at the COOLANT
TEMP indicator on the control panel
and the COOLANT HIGH TEMP
fault indicator. If either indicator shows
the engines running hot, the problem
could be a clogged air cleaner or air
intake ducts. Or the generator could
be overloaded. Read the operators
troubleshooting table for instructions.
Field level PMCS is based on an interval schedule of hours, weeks or months of
operation. Regular PMCS ensures that defects are found and fxed before they can
disable your generator. Field maintenance must complete all of the checks and services
in the TMs. Here are some of the highlights:
ENGINE OIL: Drain the engine oil according to the PMCS interval schedule. Add
the proper type of oil. Also change the oil flter. If youre in a dusty or sandy place,
change the oil and flter more often.
FUEL: Inspect the fuel/water
separator by the interval schedule. Inspect
it more often if the TQG is in constant use.
If theres water, drain it. If the fuel/water
separator has cracks, corrosion or signs of
leakage, replace it.
Inspect the engine fuel injection pump.
Look for damage or signs of leakage.
Also inspect the pump sealing gasket
for leaks. If you fnd problems, read TM
9-2815-257-24 (Nov 00) for instructions
on pump and gasket replacement.
HEAT: To keep the engine from overheating, inspect the engine air flter/air
cleaner. Look for cracks and dents. Also look for dirt and clogging. A clog chokes off
air to the engine, making it work harder. Clean or replace the flter/cleaner as needed.
Field maintenance must remove and replace the engine air flter/air cleaner at least
as often as the PMCS interval schedule requires.
The 3-kW TQG is cooled by two fans. Inspect the cooling fans for damage. Make
sure the blades turn smoothly. Replace the fans if necessary. Also check the engines
cylinder fns for dirt and debris. Clean if necessary.
Read your TMs. In the pages following the PMCS tables, youll fnd work packages
for the general inspection and service of both the generator and engine.
Field Level PMCS
Youre Responsible
Close access doors to help cool generator
If theres
water in
fuel/water
separator,
drain it
Operators and field
maintainers are
required to perform all
preventive maintenance
checks and services
assigned to them.
Lack of PMCS has
caused the TQGs and
BETSS-Cs to shut down.
Performing PMCS by the
book will keep them
running.
if the engines
hot, the coolant
could be low.
Check the coolant
level. if its low,
add more.
The 5-kW TQG
engine cooling
system consists
of a radiator,
hoses, cooling
fan, water pump,
fan belt and
overflow bottle.
Before you run
the TQG, inspect
the radiator for
dirt and debris
blocking air
flow. Clean it if
necessary.
inspect
the entire
cooling
system
for Class
III leaks,
damage,
cracks or
missing
parts.
if you find
any of these
problems,
report it
to field
maintenance.
739 50-51.indd 1-2 4/21/14 3:10 PM
52 PS 739 JUN 14 53 PS 739 JUN 14
We know extra nuts, bolts and washers can sure come in handy, especially for do-it-
yourself projects, like building a workbench or adding shelves in a tool room.
You can view off-the-shelf inventory with the Defense Logistic Agencys Inventory
Locator Network (DILNet). DILNet lists the hardware inventory available to troop
support, land, maritime and aviation supply chains from participating vendors. Best
of all, its updated every day.
You can search inventory by NSN or part number. When you fnd what you need,
you can work with a customer account specialist and submit a MILSTRIP requisition.
Hardware ships directly from vendors, with shipping times averaging only 8 days.
Urgent Reminder
Never use fasteners to repair or reassemble equipment without rst consulting the
TM. Use only the exact fasteners called for in the TM. Remember, bolts and screws are
precision materials. The wrong ones could snap under stress or not snap when they
should. And that could be dangerous, even fatal.
https://www.troopsupport.dla.mil/CE/dilnet/index.asp
Another helpful page on the website has fastener, assortment, and nuts and washer
catalogs: https://www. troopsupport. dla.mil/Hardware/Fasteners/
You also have the option to check availability of your parts or NSNs at:
https://www.troopsupport. dla.mil/CE/dilnet/CT.asp
For DILNet customer assistance, call DSN 444-5510, (215) 737-5510, or email:
[email protected]
Its here! Be sure to download and install the latest version 2.1.8 of the Electronic
Maintenance SystemNext Generation (EMS NG) Viewer and Autonomous Diagnostics
Manager (ADM) on your Maintenance Support Device (MSD). Updating the MSDs brain
helps you get the most out of interactive electronic technical manuals (IETMs).
IETMs are mailed with the version of Viewer/ADM that was current when the IETM
was published. For example, the HEMTT A4 IETM comes packaged with EMS NG v2.0. The
Viewers/ADMs are updated annually to improve performance and maintain information
assurance, but IETM updates happen less often.
So if you have trouble reading your IETMs, upgrade your version of EMS to match
(or exceed) the software version the IETM was authored in. Each update is backwards-
compatible and will work on older IETMs.
You can download the most current EMS NG Viewer/ADM from:
http://www.ems-helpdesk.com
or from AKO at: https://www.us.army.mil/suite/les/26121198
Note to MSD administrators: The EMS NG Viewer and ADM have up-to-date Certicates
of Networthiness (CoNs) and are authorized for installation on DOD network-connected
computers. The CoNs are included on the software disc. For example, youll nd the EMS
NG Viewers CoN in the folder titled EMS NG/Viewer/Certicates of Networthiness.
The CoNs ensure software security and are necessary for installing and using the EMS
NG viewer and ADM. Be aware that installing these on some Army local area networks may
require administrator rights.
If you run into problems or have questions, submit a ticket to the EMS NG help desk at:
http://www.ems-helpdesk.com
You can also call the help desk at 1-877-445-1780 or email: [email protected]
Supply
From
Soup to
Nuts
(and
Bolts)
Check out
DILNet at
Publications
Update MSDs Brain
for Best IETM Results
Gaah, I must be
getting old... vision
getting blurry,
cant remember
what sentence I was
reading in this IETM
its not you, its
your EMS NG and ADM
software. Time to
boost your brainpower
again, buddy!
Z
A
P
P
P
!
Bingo! Ive
hunted far
and wide
for you for
months.
Theres an
easier way,
Soldier.
its called
DILNet.
739 52-53.indd 1-2 5/2/14 11:09 AM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
54 PS 739 JUN 14
Dear Half-Mast,
Im a new supply sergeant learning the ropes. Is there someplace online
where I can meet similar professionals and subject matter experts (SMEs)
to ask questions or get info about my field? Thanks.
SGT R.T.
milTube
milWiki
MilWiki is a military encyclopedia and knowledge management tool. Users can
integrate and interlink knowledge into topical-based articles. Experts are encour-
aged to contribute experience and knowledge and update information.
Wikis are websites that are
editable by anyone who can
access them and this one is no
different, so the whole military
community is involved in
keeping the articles up-to-date.
milWire
MilWire promotes sharing
of existing content through
short microblog-style posts.
The format encourages short
text updates, or link sharing
from other milSuite areas and
external websites.
Ready to jump in and get your
feet wet? Grab your common
access card (CAC), meet some
folks and share what you know.
Heres the address:
https://www.milsuite.mil/
Dear Sergeant R.T.,
Yes, theres a great online tool set called milSuite that you can check out, no
matter your experience or feld of expertise.
MilSuite offers a secure way for Soldiers, DOD civilians and contractors to
unite in specialized online communities across DOD.
Users can share thoughts, ideas, lessons learned and seek assistance from
experts and peers in a whole range of topic areas. Its a great way to break the
age-old cycle of constantly reinventing the wheel.
milBook
MilBook connects people
across DOD. Its a central
hub for networking workforce
professionals, like similar
commercial social media websites.
Users can share information
through group blogs, discussions
and private wiki documents, or
create secure communities of
interest that grow and connect
with others across the greater
military community.
Internet
Make Connections on milSuite MilTube is
a platform
for sharing
videos
created
across
DOD. Youll
find videos
ranging
from
training to
news or
educational
footage.
sergeant, youre
way out here, yet
you put together
a whatsit! How
did you do it?
easy peasy!
I connected
to people
who could
help me
through
milSuite!
739 54-55.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email.
57 PS 739 JUN 14
are you ready to transfer or turn in equipment? Trying to gure out which items should
go along with the equipment and which ones you should keep? Or maybe youre a little
bafed by the difference between COEI, BII, AAL and expendable/durable supplies and
material. If so, heres the scoop!
Components of End Item (COEI) are part of the end item,
but are removed and packed separately for transportation
or shipment. These items must stay with the end item
whenever it is transferred or turned in. An example is
the antenna that goes with a radio set. COEI are
authorized by the end items TM.
Basic Issue Items (BII) are
used to set up and operate
equipment or perform
emergency repairs of
end items. BII stay with end
items throughout their service
life, even through turn-in.
An example is the retaining
bar for installing a radio set in
a vehicle. BII are authorized
by the end items TM.
Some Soldiers dont know or forget that operator TMs are
also BII. TMs should stay with vehicles or equipment whenever
its turned in or transferred. Due to cuts in the Armys printing
budget, this is more important than ever.
Additional Authorization List (AAL) items
are authorized by MTOE, TDA, or
common or joint table of
allowances for use with the end
item. Since they are optional, the
unit retains these items if the end
item is transferred or turned in.
Examples of radio AAL are cables,
adapter wires and batteries.
Expendable/durable supplies and materials are used to take care of end items. Your
unit buys them and keeps them until used up. They include things like cleaning rags,
adhesives, lubricants, rope and tape. They are authorized by CTA 50-970. For more
info, download the pub:
http://armypubs.army.mil/doctrine/DR_pubs/dr_a/pdf/cta50_970.pdf
Dear Half-Mast,
It says in AR 600-55, The Army Driver and Operator
Standardization Program (Selection, Training, Testing, and
Licensing), that supervisors must conduct annual check rides on
unit drivers/operators. Im responsible for our drivers training.
Some drivers are licensed on multiple equipment and vehicles. Is
there a requirement to give them a check ride on each piece of
equipment or vehicle, or just one? Please clarify.
Mr. W.C.
Dear Mr. W.C.,
Glad to clear things up. The reason for the annual check ride is to assess a
drivers skills, not equipment capability. So theres no requirement for supervisors
to test drivers on every piece of equipment or vehicle.
However, the option to test on more than one piece of equipment or vehicle exists
if the supervisor or examiner thinks its necessary to evaluate overall driver or
operator profciency.
As AR 600-55 explains, The purpose of the road test is to evaluate the drivers
ability to drive safely in most on-the-road situations. It serves as the basis
for issuing an operators permit and provides instructional reinforcement and
counseling. Driving weaknesses that surface as a result of the test should be called
to the attention of the examinee so that specifc steps can be taken to eliminate
these weaknesses.
By the way, Appendix G, Drivers Performance Test, has some great
info on the right way to set up road tests and assess driving skills.
Note: Look for an updated version of AR 600-55 this year.
COEI
AAL
BII
Maintenance
Management Should it Stay Or Should it Go?
Training
How Many Check Rides Required?
Me and my buddies are wondering
why we all have to get check rides!
Check rides arent really about
you guys. theyre for the drivers!
First-line
supervisors
must conduct
annual check
rides for
each driver
in Active Army
units, and
every 2 years
in Reserves
or National
Guard units.
739 56-57.indd 1-2 4/29/14 4:43 PM
Click here for a copy of this article to save or email. Click here for a copy of this article to save or email.
59 JUN 14 PS 739
Dear Half-Mast,
Im trying to understand why estimated
ship dates (ESDs) change on equipment
due-in. Every month my commander
wants equipment shortages briefed along
with the ESDs. Every month it seems
that I brief a different ESD because the
ESD is forever changing. I am trying to
understand what causes ESDs to shift.
Can you help?
Mr. A.W.
Dear Mr. A.W.,
I hear your frustration. Its important to understand and accept the fact that
ESDs will continue to shift, depending on where your unit or organization is within
the ARFORGEN cycle. Equipment sourcing is based on mission needs for those in
deployment cycles, and mission requirements in other cases.
But that doesnt mean you dont have tools for getting a better grip on ESDs.
The Logistics Support Activitys Logistics Information Warehouse (LIW) rides to
the rescue!
Options #1 and #3 can help determine where your unit is in the fll order, and
options #2 and #4 will give your documents status. After you submit a request
in PBUSE, you should interface daily (blast process or by Secure File Transfer
Protocol [SFTP]) with the Standard Army Retail Supply System (SARSS) or
Global Combat Support System-Army (GCSS-Army) to get an updated status
on your requisition.
You can fnd all these great LIW tools, instructions and more at:
https://liw.logsa.army.mil/
Note: No animals were harmed
in the making of this article.
1 2
4 3
Use the Decision Support Tool in LIW, which
displays the ll level of your organization,
reecting the ARFORGEN cycle.
Use ILAP in LIW to verify the equipments
availability and on-hand balance.
Try a WebLIDB pipeline query to verify the
requisition status.
Contact the equipments item manager or
project manager to verify where your unit
or organization falls in the ll order.
1
2
4
3
Get a Grip on ESDs
Supply Management
Get a Grip on ESDs
LOGSAs LIW offers multiple
options for rming up ESDs
Thanks to Half-Mast and
LIW, weve got everything
we need to get a handle
on these ESDs!
The best way to wrangle in ESDs is
with the tools provided by LOGSAs
Logistics Information Warehouse!
739 58-59.indd 1-2 4/21/14 3:09 PM
Click here for a copy of this article to save or email.
DISTRIBUTION: To be distributed in accordance with the initial distribution number (IDN) 345239, requirements for the TB 43-PS-Series.
60 PS 739 JUN 14
Free FRS RetroftIf You Act Fast!
Units with older M7 forward repair systems (FRS), NSN 4940-01-533-1621, are eligible for a free
tool retrot if they act fast. The retrot will make the older systems align with SC 4940-95-E42.
Only some M7s with serial numbers 1999-3 and below are eligible.
To see if your M7 is on the serial number list, go to:
https://tulsa.tacom.army.mil/Maintenance/?t=mam&f=RetLisFRSsernum17MAR.pdf
If your FRS is eligible, order the retrot kit at:
https://tools.army.mil
The deadline for ordering the free kit is July 14, 2014. Follow the ordering instructions
in TACOM MAM 11-038:
https://tulsa.tacom.army.mil/Maintenance/message.cfm?id=MA14-030.html
Questions? Contact TACOMs Donald Hoisington at DSN 786-6951, (586) 282-6951, or by email:
[email protected]
Or contact Brian Egli at DSN 786-6968, (586) 282-6968, or by email:
[email protected]
Backhoe Loader
Roof Pad NSN
On Page 21 of PS 729 (Aug 13), we said you
could get a new roof pad for your backhoe
loader (BHL) with NSN 2510-01-582-5088.
Turns out that NSN actually brings a roll of
door seal insulation. The correct NSN for the
roof pad is 2540-01-548-9159.
M400T/W Skid Loader
Door Assembly
Get a new door assembly for your M400T or
M400W compact skid loader with NSN 2510-
01-593-8321 (PN 87724852). NSN 5330-01-
566-3948 (PN 87724851), which is shown as
Item 36 in Fig 66 of TM 5-3805-292-23P (Mar
10), brings a gasket, not the door assembly.
New NSN for M1070A0/A1 HET Wheel Hub
Need to order a new wheel hub assembly seal for your M1070A0/A1 HET? Get it with NSN 5330-
01-549-9595. That replaces NSN 5330-01-350-2906, which is shown as Item 3 in Fig 164 of TM
9-2320-360-24P (Feb 98) and Figs 156 and 158 of TM 9-2320-427-13&P in IETM EM 0310 (Jan 11).
The old NSN is a terminal item.
FMTV Brake Spider NSNs
Need a new brake spider for your FMTV? The brake
spider with 10 unthreaded holes comes with NSN
2530-01-467-4098. Get a brake spider thats tapped
with 10 threaded holes with NSN 2530-01-588-7963.
Make a note until these NSNs are updated in Fig 133
of TM 9-2320-365-24P for the 2
1
/2-ton LMTV, and Fig
161 of TM 9-2320-366-24P-1 for the 5-ton MTV.
Soutache Braid in the ASU Pocket
There is no NSN for the soutache braid worn on the sleeve of your blue Army service uniform
(ASU). The Army issues the blue ASU coat with the braid inside one of the pockets. So, check all
the pockets when you receive your coat.
If you dont nd the braid, contact the Defense Logistics Agency (DLA) Troop Support Clothing
and Textiles Army Recruit Clothing Team:
Ellen Henning at (215) 737-2482, or email: [email protected]
Or Gerald Iuliucci, (215) 737-8610, or email: [email protected]
Theyll work with the vendor to have the braid sent directly to you.
GCSS-Army Reminder
Remember to check the GCSS-Army website
for alerts, updated elding and training
schedules and other important info. Visit:
https://gcss.army.mil/
Or sign up to get automatic notications at:
https://gcss.army.mil/Support/register.aspx
SATS Door Handle
NSN Change
Get a new generator access door T-handle
for your SATS with NSN 5340-01-603-1874.
It replaces NSN 5340-01-534-2834, which is
shown as Item 3 in Fig 5-6 of TM 9-4910-783-
13&P (Sep 05). That NSN is a terminal item.
DA Pam 750-43 Revised
A major revision to DA Pam 750-43, Army Test
Program Set Implementation Guide (Maintenance
of Supplies and Equipment), went into effect in
January 2014. The revision covers various subjects,
including program management, test program
set requirements, acquisition, engineering
development management, product assurance
and tests. There are also numerous terminology
changes.
Download the pub at:
http://www.apd.army.mil/pdfles/p750_43.pdf
PLS Basic
First Aid Kit
The basic rst aid kit, NSN 6545-00-922-
1200, is a basic issue item (BII) for the
M1074/A1 and M1075/A1 palletized
loading system (PLS). Some of the kits
medical supply items have expiration
dates. So when you receive a newly elded
truck, check the kit for expired items. Take
any expired items to your local medical unit
and exchange them for new ones.
ATLAS, 6K VRRTFL Fork Extensions Not Authorized
Fork extensions are not authorized for use on the ATLAS, ATLAS II, or 6K variable reach
rough-terrain forklift (VRRTFL). Thats the ofcial word from both TACOM LCMC and JLG, the
manufacturer of the forklifts.
739 60-61.indd 1-2 4/29/14 4:42 PM
Click here for a copy of these articles to save or email.
save your
sight
use combat
eyewear
save your
sight
use combat
eyewear
Click here for a copy of this article to save or email.