The document provides guidance on writing a laboratory report for an experiment on ship resistance. It recommends following an IMRADC structure - Introduction, Methods, Results, Discussion, and Conclusion. The introduction should state the purpose and aims of the report. The methods section should describe the experimental setup and procedures in enough detail to allow replication. The results and discussion sections should present measurements, calculations, and plots with clear labeling and referencing. The conclusion should state the main findings and how the objectives were met. Proper grammar, style, and technical writing conventions are also encouraged.
The document provides guidance on writing a laboratory report for an experiment on ship resistance. It recommends following an IMRADC structure - Introduction, Methods, Results, Discussion, and Conclusion. The introduction should state the purpose and aims of the report. The methods section should describe the experimental setup and procedures in enough detail to allow replication. The results and discussion sections should present measurements, calculations, and plots with clear labeling and referencing. The conclusion should state the main findings and how the objectives were met. Proper grammar, style, and technical writing conventions are also encouraged.
The document provides guidance on writing a laboratory report for an experiment on ship resistance. It recommends following an IMRADC structure - Introduction, Methods, Results, Discussion, and Conclusion. The introduction should state the purpose and aims of the report. The methods section should describe the experimental setup and procedures in enough detail to allow replication. The results and discussion sections should present measurements, calculations, and plots with clear labeling and referencing. The conclusion should state the main findings and how the objectives were met. Proper grammar, style, and technical writing conventions are also encouraged.
Youve probably had lots of advice on how to write a lab report. What Ive presented here isnt intended to be definitive: its meant as guidance. Basically, when you write a lab report, you should provide enough information so that the reader could repeat your experiments. You shouldnt start by asking How long should this report be? It should be as long as it has to be, and no longer.
As for format, I suggest you follow the IMRADC structure. That is, the report should include an Introduction, a description of the Methods and equipment used, a presentation of the Results, a Discussion of the results, and Concluding remarks. These are discussed briefly below.
Introduction
In the introduction, you should state first, in simple terms, what the report is. You should then explain what its purpose, or aim, is. For example:
The subject of this report is a resistance experiment done with a 1:20 scale model of the ship Mk-123. The experiment was done by ONAE-2006 for the Elbonian Navy. The purpose of the experiment was to determine the resistance of the bare hull form of Mk-123 over a range of speeds corresponding to the full-scale speed range of 4 to 24 knots. An additional objective of the experiment was to determine the hulls form factor.
You may include other relevant information in the introduction, such as the scope and background of the work, which might help the reader appreciate what you have done and how you are about to report it. For example, you might explain the scope of the experiments as follows:
The experiments were done in accordance with the ITTC-78 test procedures. Form factor was determined using Prohaskas method. Tests were done at roughly equal 1 knot speed intervals from 5 knots to 24 knots. The speed interval was reduced to a half knot near the design speed of 22.5 knots. Tests were repeated at several speeds to check on the repeatability of the measurements. All the measured results are tabulated and presented in the report. Results are also presented as plots of resistance coefficient versus Froude number.
This (above) tells the reader the overall extent of the tests and also gives some indication of how s/he can expect to see the results presented. As for background, in our case, it might be:
These experiments were done as part of the course requirements for ENGR 5011. The purpose of the lab exercise was to become acquainted with the process of planning, executing, and analyzing model test data in order to make full-scale predictions of ship resistance for the smooth hull. A log book was also kept. Engr 5011 Resistance & Propulsion of Ships Laboratory Exercises: Winter, 2008 Lab report writing.doc Brian Veitch, EN4042, Tel: 737-8970, e-mail: [email protected]
The introduction should stick to the main facts and these should be related to the reader in clear, simple language. Before you begin writing, you should understand the matter thoroughly and have a clear plan for presenting it in an organized format.
Methods
This section is very important and tends to be the one most likely to be under reported. It should provide enough information to allow another investigator (with skills nominally equal to your own) to repeat the experiment you did. This means that you have to give a detailed account of the test setup, which can often be aided with complementary figures, and specify the equipment that you used. You neednt include detailed calibration procedures nor results in the report, but you must have these in your log book. I suggest you include them in the report. You can start by explaining the approach that youve used to accomplish your stated goals.
The resistance and form factor of the Mk-123 unappended hull form was evaluated experimentally using the ITTC 78 test procedures and Prohaskas method, respectively. A step-by-step account of the procedure is given below, along with a description of the test setup. .
I recommend starting with the setup and then moving on to the methods. These can be sub- sections. Incorporate figures with care. Figures should be complemented by accompanying text and vice versa.
You have to present all the equations that you use in your analysis method, including any necessary explanations. Dont give tables of computed results (e.g. in a spreadsheet) without showing the corresponding equations. This advice applies to assignments too.
Equations should be numbered and referred to in the text by the number, as in the resistance coefficient calculated in accordance with equation (7) is then
Its important to give a balanced description of your setup and method. Provide the essential facts and details, but avoid digressions and discussions. You can refer the reader to other sources for additional details.
Results and discussion
If you prefer, you can present only the results in this section and refrain from adding a discussion until the conclusion section. Sometimes, it is better to include your discussion along with the results. Its up to you.
If you present all the measurements that you made, say in tables, then you should tell the reader that they are measurements (rather than calculated values).
Likewise, if you present plots of results, you should describe carefully what appears on the plot. This includes telling what the plot axes are, what the symbols indicate, and what any lines are. For example, if you fit a curve through some data points, you should tell what kind of line it is. Also, if you plot an equation, say for comparison, dont use point symbols for the same equation: point symbols should be used for experimental results.
Conclusion
You should state your findings in this section. If you dont know what you should be saying here, refer back to your introduction. Presumably, youve stated clearly there what the objectives of the work were. Now you can tell the conclusions. In our sample case, you should at least tell that resistance was evaluated over some specified speed range, give the numerical value of resistance at the design speed, and give the form factor.
A matter of style
You should also be conscious of matters of grammar and style. Sentences should be grammatically correct. You should use complete sentences, not sentence fragments. Be careful of your punctuation. Avoid run-on sentences. Avoid using the same word to start every sentence. Conversely, dont affect a style that is inappropriate to the subject matter. And as always, keep it simple and to the point.
Normally, formal technical writing is done in the passive voice. This can make it a bit dry. Dont slip in and out of voice and tense. You can get good advice on matters of style, grammar, and punctuation from lots of sources. I like Strunk & Whites The Elements of Style. Its concise.