Professional Documents
Culture Documents
Laboratorios de Sensores PDF
Laboratorios de Sensores PDF
Sensors for
Handling and
Processing
Technology
Proximity Sensors
Workbook
BN(1)
BU(3)
BK(4)
BN(1)
BU(3)
+24 V DC
0 V
Order no.: 529939
Description: ARBEITSBUCH
Designation: D.LW-FP1110-GB
Edition: 11/01
Author: Frank Ebel
Graphics: Brbel Bhland, Frank Ebel
Layout: 09.11.2001, Frank Ebel, Beatrice Huber
Festo Didactic GmbH & Co., D-73770 Denkendorf, 2001
Internet: www.festo.com/didactic
e-mail: [email protected]
The copying, distribution and utilization of this document as well as the
communication of its contents to others without expressed authorization is
prohibited. Offenders will be held liable for the payment of damages. All rights
reserved, in particular the right to carry out patent, utility model or ornamental
design registration.
Festo Didactic GmbH & Co. FP1110 3
Preface _____________________________________________________________ 6
Component order numbers _______________________________________________ 7
Set of test objects_______________________________________________________ 8
Proximity sensors______________________________________________________ 10
Components/Exercises Table ____________________________________________ 13
Notes on safety and operation ___________________________________________ 15
Part A Exercises
Magnetic proximity sensors
Exercise 1
Switching characteristics of a contacting magnetic proximity sensor___________ A-3
Exercise 2
Switching characteristics of a contactless magnetic proximity sensor _________ A-13
Inductive proximity sensors
Exercise 3
Switching distance of an inductive proximity sensor _______________________ A-23
Exercise 4
Sensing of different metals with inductive proximity sensors ________________ A-31
Exercise 5
Influence of the object surface on the switching distance ___________________ A-39
Optical proximity sensors
Exercise 6
Response characteristics of a through-beam sensor _______________________ A-47
Exercise 7
Response characteristics of a retro-reflective sensor _______________________ A-57
Exercise 8
Sensing range of a diffuse optical sensor ________________________________ A-67
Exercise 9
Sensing range of a diffuse optical sensor with fibre-optic cable ______________ A-81
Capacitive proximity sensors
Exercise 10
Switching distance of a capacitive sensor ________________________________ A-89
Exercise 11
Influence of material thickness
on the switching distance of a capacitive sensor __________________________ A-99
Contents
Contents
4 Festo Didactic GmbH & Co. FP1110
Ultrasonic proximity sensors
Exercise 12
Sound wave form and reflection characteristics of an ultrasonic sensor ______ A-107
Applications
Exercise 13
Speed measurement ________________________________________________ A-117
Exercise 14
Determining rotational speeds ________________________________________ A-127
Exercise 15
Sensing the correct assembly of workpieces_____________________________ A-137
Exercise 16
Liquid level measurement ____________________________________________ A-145
Exercise 17
Checking of threads _________________________________________________ A-155
Exercise 18
Logic combinations of proximity sensor signals __________________________ A-163
Exercise 19
Position detection with proximity sensors_______________________________ A-171
Part B Fundamentals
Textbook 'Proximity Sensors' ___________________________________________ B-1
Part C Solutions
Magnetic proximity sensors
Solution 1
Switching characteristics of a contacting magnetic proximity sensor___________ C-3
Solution 2
Switching characteristics of a contactless magnetic proximity sensor __________ C-5
Inductive proximity sensors
Solution 3
Switching distance of an inductive proximity sensor ________________________ C-7
Solution 4
Sensing of different metals with inductive proximity sensors _________________ C-9
Solution 5
Influence of the object surface on the switching distance ___________________ C-11
Contents
Festo Didactic GmbH & Co. FP1110 5
Optical proximity sensors
Solution 6
Response characteristics of a through-beam sensor _______________________ C-13
Solution 7
Response characteristics of a retro-reflective sensor _______________________ C-15
Solution 8
Sensing range of a diffuse optical sensor ________________________________ C-17
Solution 9
Sensing range of a diffuse optical sensor with fibre-optic cable ______________ C-21
Capacitive proximity sensors
Solution 10
Switching distance of a capacitive sensor ________________________________ C-23
Solution 11
Influence of material thickness
on the switching distance of a capacitive sensor __________________________ C-25
Ultrasonic proximity sensors
Solution 12
Sound wave form and reflection characteristics of an ultrasonic sensor _______ C-27
Applications
Solution 13
Speed measurement _________________________________________________ C-29
Solution 14
Determining rotational speeds _________________________________________ C-31
Solution 15
Sensing the correct assembly of workpieces______________________________ C-33
Solution 16
Liquid level measurement _____________________________________________ C-35
Solution 17
Checking of threads __________________________________________________ C-37
Solution 18
Logic combinations of proximity sensor signals ___________________________ C-39
Solution 19
Position detection with proximity sensors________________________________ C-41
Part D Data sheets
6 Festo Didactic GmbH & Co. FP1110
The workbook was designed for the equipment set of function package FP1110 -
Proximity Sensors.
This workbook provides basic knowledge of proximity sensors in conjunction with
textbook Proximity Sensors (order no. 093046).
Technical data regarding the equipment used can be found in part D of the
workbook.
You will find the order numbers of the individual components on the following
pages.
Each exercise consists of exercise sheets and solution sheets. Each exercise sheet
contains summarised details of:
Training aim
Exercise definition
Problem description and further explanations for the practical assembly of the
exercise
Sample solution
To assist assembly, a practical layout is included. Special calculations and
conclusions are provided in the sample solutions.
Warning
The positioning slide D.ER-VS-FP1110 and the set of test objects D.AS-OS contains
strong magnets. Objects of magnetic sensitivity (i.e. floppy disks, cheque cards)
should not be placed close to the magnets.
Preface
Preface
Festo Didactic GmbH & Co. FP1110 7
Qty. Description Designation Order no.
1 Sensor unit, magnetic 1, Reed contact D:ER-SMEO-PP-SIBU 167056
1 Sensor unit, magnetic 2, contactless D:ER-SMTO-PP-SIBU 167055
1 Sensor unit, inductive 1 D:ER-SIEH-M18B-PP-SIBU 177466
1 Sensor unit, inductive 2 D:ER-SIEH-M12B-PP-SIBU 177464
1 Sensor unit, optical RT 1,
diffuse sensor
D:ER-SOE-RT-Q-PP-SIBU 167068
1 Sensor unit, optical RT 2,
diffuse sensor
D:ER-SOE-RT-M18-PP-SIBU 167166
1 Sensor unit, optical RS,
retro-reflective sensor
D:ER-SOE-RS-Q-PP-SIBU 167066
2 Sensor unit, optical LL 1
fibre-optic unit
D:ER-SOE-L-Q-PP-SIBU 167065
1 Sensor unit, optical ESS,
through-beam sensor emitter
D:ER-SOE-S-Q-PP-SIBU 167064
1 Sensor unit, optical ESE,
through-beam sensor receiver
D:ER-SOE-E-Q-PP-SIBU 167067
1 Sensor unit, capacitive D:ER-SKE-M12-PP-SIBU 177470
1 Sensor unit, ultrasonic D:ER-SUE-M18-PP-SIBU 184118
2 Fibre-optic cable unit SE,
through-beam sensor design
D:ER-SOEZ-LK-SE-PP 150505
1 Fibre-optic cable unit RT,
diffuse sensor design
D:ER-SOEZ-LK-RT-PP 150506
1 Reflector unit D:ER-SOEZ-RFS20-PP 150504
1 Positioning slide * D:ER-VS-FP1110-ST 034094
1 Distribution unit * D:ER-VERT-SENSOR-SIBU 162248
1 Counting unit * D:ER-ZE-FP1110-SIBU 162252
1 Rotary unit * D:ER-DE-FP1110-SIBU 167097
1 Set of test objects D:AS-OS 034083
1 Measuring scale 1020 mm D:ER-LIN-1020 035697
1 Graph paper pad D:AS-RK 034085
16 Plug-in adapters D:MP-B-ME-AS 323571
* 4 plug-in adapters are necessary to mount this unit on the profile plate.
Equipment set FP1110
Order no.: 184474
Preface
8 Festo Didactic GmbH & Co. FP1110
The following elements are adapted to the equipment set:
Qty. Description Designation Order no.
Courseware
1 Textbook D:LB-FP1110-D 093046
Accessories
1 Vernier caliper D:AS-MS 035653
1 Digital multimeter D:AS-DMM 035681
Equipment
1 Profile plate 1100 x 700
or
Profile plate 550 x 700
D:DE-PP-1100
D :DE-PP-550
159411
159409
Power supply
1 Power supply unit D:AS-NG-D-115/230V 162417
1 Set of cables D:AS-KS-4MM-UNI-SIBU 167091
Item no. Material, Dimensions [mm]
1 Magnet 1
2 Magnet 2
3 Mild steel S 235 JR, 90 x 30
4 Stainless steel, 90 x 30
5 Aluminium, 90 x 30
6 Brass, 90 x 30
7 Copper, 90 x 30
8 Cardboard, 90 x 30
9* Rubber, 90 x 30
10 Plastic, transparent, 90 x 30
Accessories
Set of test objects
components
Preface
Festo Didactic GmbH & Co. FP1110 9
Item no. Material, Dimensions [mm]
11 Mild steel S 235 JR, 30 x 30
12 Mild steel S 235 JR, 25 x 25
13 Mild steel S 235 JR, 20 x 20
14 Mild steel S 235 JR, 15 x 15
15 Mild steel S 235 JR, 10 x 10
16 Mild steel S 235 JR, 5x 5
17 Kodak grey card, 100x 100
18 Plastic, transparent, 100x 100
19 Plastic, red, 100x 100
20 Plastic, blue, 100x 100
21 Plastic, black, 100x 100
22 Cardboard, white, 100 x100
23 Plastic, 2.0 mm thick, 90 x 30
24 Plastic, 3.0 mm thick, 90 x 30
25 Plastic, 5.0 mm thick, 90 x 30
26 Plastic, 8.0 mm thick, 90 x 30
27 Plastic, 11.0 mm thick, 90 x 30
28 Plastic, 14.0 mm thick, 90 x 30
29 Plastic, 17.0 mm thick, 90 x 30
30 Holder for fibre-optic cable
31 Base plate with gear wheels
32 Holding brackets for liquid level measurement, through-beam sensor (2)
33 Beaker
34 Test screws (2)
35 Workpiece valve housing
36 Screw driver
* Component part not identified with a number.
Set of test objects
components (continued)
Preface
10 Festo Didactic GmbH & Co. FP1110
Except for the magnetic proximity sensor with Reed contact (D.ER-SMEO-..), all
sensors in this function package are designed as positive switching proximity
sensors with transistor output (PNP type). With this type of proximity sensor, the
output line is with positive potential in the switched state. With a connected load,
one terminal is thus connected to the proximity sensor signal output, while the other
terminal is linked to 0 Volt (ground).
We are dealing here with proximity sensors of three and four wire technology.
Outputs have either normally open or normally open and normally closed function.
Electrical connection diagram
L
Connection diagram of a three wire proximity sensor (L=load)
L
Connection diagram of a four wire proximity sensor (L=load)
Proximity sensors
Preface
Festo Didactic GmbH & Co. FP1110 11
Operating voltage
Positive pole brown
Negative pole (0 V) blue
Load output
With three connecting wires
irrespective of function black
With four connecting wires
Normally open function black
Normally closed function white
Colour coding for connecting wires of inductive proximity sensors according to Euronorm EN 50 044
The colour coding and the numerical identification of connecting wires is laid down
only for inductive proximity sensors in Euronorm EN 50 044. For the other types of
proximity sensor, colour coding and numerical identification of connecting wires are
not standardised; however, identification codes are frequently based on the
Euronorm for inductive proximity sensors.
Operating voltage
Positive pole 1
Negative pole (0 V) 3
Load output
Normally open function 4
Normally closed function 2
Numerical identification for connecting wires of inductive proximity sensors according to Euronorm EN 50 044
Colour coding and
connection identification
Preface
12 Festo Didactic GmbH & Co. FP1110
Colour Abbreviation
black BK
brown BN
blue BU
red RD
grey GY
white WH
Colour abbreviations according to DIN IEC 757
Further information on technical data concerning proximity sensors will be found in
the data sheets.
Colour abbreviations
Preface
Festo Didactic GmbH & Co. FP1110 13
Exercises Components
(Description, Designation)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Profile plate 1100 x 700
D:DE-PP-1100
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Power supply unit
D:AS-ND-D-115/230V
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Set of cables
D:AS-KS-4MM-UNI-SIBU
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Distribution unit
D:ER-VERT-SENSOR-...
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Positioning slide
D:ER-VS-FP1110-ST
1 1 1 1 1 1 1 1 1 1 1 1 1
Counting unit
D:ER-ZE-FP1110-SIBU
1 1 1
Rotary unit
D:DE-DE-FP1110-SIBU
1
Sensor unit, magnet. 1
D:ER-SMEO-...
1
Sensor unit, magnet. 2
D:ER-SMTO-...
1
Sensor unit, inductive 1
D:ER-SIEH-M18B-...
1 1 1 1
Sensor unit, inductive 2
D:ER-SIEH-M12B-...
1 1
Sensor unit, capacitive
D:ER-SKE-M12-...
1 1 1 1
Sensor unit, opt. RT 1,
D:ER-SOE-RT-Q-...
1
Components/Exercises
Table
Preface
14 Festo Didactic GmbH & Co. FP1110
Exercises Components
(Description, Designation)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Sensor unit, opt. ESS
D:ER-SOE-S-Q-...
1 1
Sensor unit, opt. ESE
D:ER-SOE-E-Q-...
1 1
Sensor unit, opt. RS
D:ER-SOE-RS-Q-...
1
Reflector unit
D:ER-SOEZ-RFS20-...
1
Sensor unit, opt. LL 1
D:ER-SOE-L-Q-...
1 2 1 1 1 1 2
Fibre-optic cable unit SE
D:ER-SOEZ-LK-SE-...
2 2
Fibre-optic cable unit RT
D:ER-SOEZ-LK-RT-...
1 1 1 1 1
Sensor unit, opt. RT 2
D:ER-SOE-RT-M18-...
1
Sensor unit, ultrasonic
D:ER-SUE-M18-...
1
Measuring scale 1020 mm
D:AS-LIN-1020
1 1
Vernier caliper
D:AS-MS
1 1 1 1 1 1 1 1 1 1
Digital multimeter
D:AS-DMM
1 1
Set of test objects
D:AS-OS
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Graph paper pad
D:AS-RK
1 1 1 1 1
Components/Exercises
Table (continued)
Festo Didactic GmbH & Co. FP1110 15
In the interest of your own safety you should observe the following:
Observe general safety regulations!
(DIN 58126 and VDE 100).
Use only low voltages of 24 V.
All components are provided with 4 mm safety sockets respectively safety plugs.
For electical connections use only electrical cable with safety plugs.
Switch off the voltage supply before connecting or disconnecting the circuit.
The positioning slide D.ER-VS-FP1110 and the set of test objects D.AS-OS
contains strong magnets. Objects of magnetic sensitivity (i.e. floppy disks,
cheque cards) should not be placed close to the magnets.
When the operating voltage is switched on, the motor starts up immediately with
a rotational speed of about 2500 r.p.m.
Notes on safety and operation
16 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-1
Part A Exercises
Magnetic proximity sensors
Exercise 1
Switching characteristics of a contacting magnetic proximity sensor___________ A-3
Exercise 2
Switching characteristics of a contactless magnetic proximity sensor _________ A-13
Inductive proximity sensors
Exercise 3
Switching distance of an inductive proximity sensor _______________________ A-23
Exercise 4
Sensing of different metals with inductive proximity sensors ________________ A-31
Exercise 5
Influence of the object surface on the switching distance ___________________ A-39
Optical proximity sensors
Exercise 6
Response characteristics of a through-beam sensor _______________________ A-47
Exercise 7
Response characteristics of a retro-reflective sensor _______________________ A-57
Exercise 8
Sensing range of a diffuse optical sensor ________________________________ A-67
Exercise 9
Sensing range of a diffuse optical sensor with fibre-optic cable ______________ A-81
Capacitive proximity sensors
Exercise 10
Switching distance of a capacitive sensor ________________________________ A-89
Exercise 11
Influence of material thickness
on the switching distance of a capacitive sensor __________________________ A-99
Part A
Part A
A-2 Festo Didactic GmbH & Co. FP1110
Ultrasonic proximity sensors
Exercise 12
Sound wave form and reflection characteristics of an ultrasonic sensor ______ A-107
Applications
Exercise 13
Speed measurement ________________________________________________ A-117
Exercise 14
Determining rotational speeds ________________________________________ A-127
Exercise 15
Sensing the correct assembly of workpieces_____________________________ A-137
Exercise 16
Liquid level measurement ____________________________________________ A-145
Exercise 17
Checking of threads _________________________________________________ A-155
Exercise 18
Logic combinations of proximity sensor signals __________________________ A-163
Exercise 19
Position detection with proximity sensors_______________________________ A-171
Festo Didactic GmbH & Co. FP1110 A-3
To learn about the switching characteristics of a contact based magnetic proximity
sensor (Reed contact) as a function of position and orientation of a magnet.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 1
Switching characteristics of a contacting magnetic proximity sensor
Training aim
Exercise definition
Exercise 1
A-4 Festo Didactic GmbH & Co. FP1110
Metallic workpiece supports are transported on a conveyor. The position of a
workpiece support is to be defined by means of a contact-based magnetic sensor
(Reed contact). For this purpose, a permanent magnet is fitted to the workpiece
support. Define the switching curve of this sensor.
1 2
3
Proximity sensor (1), Magnet (2), Workpiece support (3)
Problem description
Positional sketch
Exercise 1
Festo Didactic GmbH & Co. FP1110 A-5
The magnetic field sensitive Reed contact is located behind a black plastic plate. The
magnetic field of a permanent magnet switches the Reed contact by contactless
means. The Reed contact consists of two separate flexible blades made from soft
magnetic material, fitted in a hermetically sealed glass tube. When placed in an
external magnetic field, these blades touch and establish an electrical contact.
3
1
2
1 (24 V DC)
4 ( )
3 (0 V)
Reed contact (1), Switching status indicator (LED) (2), Active zone (3)
Function description
Exercise 1
A-6 Festo Didactic GmbH & Co. FP1110
1
4
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Magnetic sensor unit 1, D:ER-SMEO-...
4 1 Set of test objects, magnet 1, part 1
1 Set of test objects, magnet 2, part 2
Layout
Components list
Exercise 1
Festo Didactic GmbH & Co. FP1110 A-7
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Magnetic sensor unit 1, D:ER-SMEO-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 1
A-8 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the positioning slide and the magnetic sensor unit 1 on
the profile plate. Mount the magnetic sensor unit laterally offset by 5 cm in relation
to the centre of the positioning slide (see fig. "Layout"). Connect the 24V electrical
power supply and the magnetic proximity sensor to the distribution unit (see fig.
"Electrical connections").
Attach the vernier caliper to the positioning slide.
Experiment 1
Take magnet 1 (part 1) from the set of test objects and attach it to the material
retainer of the positioning slide.
Move the magnet along the axis of the proximity sensor. Write down the points at
which the proximity sensor responds to the magnet. You recognise this response by
the illumination of the LED built into the proximity sensor and the sounding of the
buzzer forming part of the distribution unit. Enter the response points into the
diagram on the following page. The distance between magnet and proximity sensor
is increased in 2 mm steps (in correspondence with the division on the magnet
holder, starting from 0 mm; the displacement path of the positioning slide (stroke) is
selected 50 mm in relation to the centre of the active area of the proximity sensor.
The displacement path must be fully travelled for each measurement.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set to
"0". The two pointers are moved apart by approximately 10 mm. The vernier caliper
is placed parallel to the base plate flush with the edge in such a way, that the front
pointer rests against the stop for the vernier caliper. The two retaining magnets
retain the caliper body to the base plate of the positioning slide.
Practical assembly
Exercise 1
Festo Didactic GmbH & Co. FP1110 A-9
Experiment 2
Now take magnet 2 (part 2) from the set of test objects and repeat the procedure
described above. Again record the response points and mark the values in the
diagram.
Note
When making your measurements, observe that the switch-on and switch-off points
of the proximity sensor do not coincide: let the magnet approach the inactive
proximity switch from the left, until this changes its switching status, thus obtaining
its switch-on point. Now move the magnet away towards the left until the proximity
sensor changes from the active to the inactive state, thus obtaining the switch-off
point. The distance travelled between the two points is described as hysteresis.
Exercise 1
A-10 Festo Didactic GmbH & Co. FP1110
Exercise 1
Festo Didactic GmbH & Co. FP1110 A-11
Magnet 1 (part1)
60
20
5
0
-25
-60
-55
-50
-45
-40
-35
-30
-20
-15
-10
-5
10
15
25
30
35
40
45
50
mm
0 20 40 40 30 10
0 mm 50 30 20 10
S
t
r
o
k
e
Distance
Evaluation
Experiment 1
Exercise 1
A-12 Festo Didactic GmbH & Co. FP1110
Magnet 2 (part 2)
60
20
5
0
-25
-60
-55
-50
-45
-40
-35
-30
-20
-15
-10
-5
10
15
25
30
35
40
45
50
mm
0 20 40 40 30 10
0 mm 50 30 20 10
S
t
r
o
k
e
Distance
Evaluation
Experiment 2
Festo Didactic GmbH & Co. FP1110 A-13
To learn about the switching characteristics of a magnetic proximity sensor with
electronic output dependent on position and orientation of a magnet.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 2
Switching characteristics of a contactless magnetic proximity sensor
Training aim
Exercise definition
Exercise 2
A-14 Festo Didactic GmbH & Co. FP1110
In order to measure the rotation rate of a non-metallic gear wheel, it is intended to
use a contactless proximity sensor. For this purpose, a magnet is attached to a
positon on the gear wheel. In order to achieve reliable switching, the switching curve
of this proximity switch is to be recorded. The influence of the orientation of the axis
of the magnetic poles is also to be investigated.
Problem description
Positional sketch
Exercise 2
Festo Didactic GmbH & Co. FP1110 A-15
With this contactless sensor (D.ER-SMTO-..), the magnetic field sensitive area is
identified with a blue dot. The detection of the magnetic field is achieved through
the tuning of an oscillator which is built into the sensor. As the magnet approaches,
the ferrite core of a high-frequency oscillator is saturated. This varies the current in
the oscillator circuit. The current change is converted into an output signal by means
of an amplifier circuit.
6
Oscillator (1), Demodulator (2), Triggering stage (3), Switching status
indicator (LED) (4), Output stage with protective circuit (5), External voltage (6),
Internal stabilised voltage (7), Active switching zone (coil) (8),
Switching output (9)
Function description
Exercise 2
A-16 Festo Didactic GmbH & Co. FP1110
1
4
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Magnetic sensor unit 2, D:ER-SMTO-...
4 1 Set of test objects, magnet 1, part 1
1 Set of test objects, magnet 2, part 2
Layout
Components list
Exercise 2
Festo Didactic GmbH & Co. FP1110 A-17
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Magnetic sensor unit 2, D:ER-SMTO-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 2
A-18 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the positioning slide and the magnetic sensor unit 2 on
the profile plate. Mount the magnetic sensor unit 5 cm offset from the centre of the
positioning slide (see fig. "Layout"). Connect the 24V electrical power supply and
the magnetic sensor to the distribution unit (see fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Experiment 1
Take magnet 1 (part 1) from the set of test objects and fit it into the material fixture
of the positioning slide.
Move the magnet along the axis of the sensor. Make a note of the points where the
sensor responds to the magnet. This response can be seen by illumination of the
LED, which is built into the magnetic sensor, and by the sounding of the buzzer,
which is built into the distribution unit. Record the results in the evaluation tables.
The magnet-sensor distance starting from 0 mm increases in steps of 2 mm (in
correspondence with the division of the magnet holder), the displacement path for
the positioning slide (stroke) is selected 50 mm in relation to the centre of the active
area of the sensor (blue dot). The displacement path must be fully travelled for each
measurement.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly
Exercise 2
Festo Didactic GmbH & Co. FP1110 A-19
Experiment 2
Now take magnet 2 (part 2) from the set of test objects and repeat the above
procedure. Again, make a note of the switching points.
Note
When making your measurement, observe that the switch-on and switch-off points
of the proximity sensor do not coincide: let the magnet approach the inactive
proximity switch from the left, until this changes its switching status, thus obtaining
its switch-on point. Now move the magnet away towards the left until the sensor
changes from the active to the inactive state, thus obtaining the switch-off point.
The distance travelled between the two points is described as hysteresis.
Exercise 2
A-20 Festo Didactic GmbH & Co. FP1110
Exercise 2
Festo Didactic GmbH & Co. FP1110 A-21
Magnet 1 (part 1)
60
20
5
0
-25
-60
-55
-50
-45
-40
-35
-30
-20
-15
-10
-5
10
15
25
30
35
40
45
50
mm
0 20 40 40 30 10
0 mm 50 30 20 10
S
t
r
o
k
e
Distance
Evaluation
Experiment 1
Exercise 2
A-22 Festo Didactic GmbH & Co. FP1110
Magnet 2 (part 2)
60
20
5
0
-25
-60
-55
-50
-45
-40
-35
-30
-20
-15
-10
-5
10
15
25
30
35
40
45
50
mm
0 20 40 40 30 10
0 mm 50 30 20 10
S
t
r
o
k
e
Distance
Evaluation
Experiment 2
Festo Didactic GmbH & Co. FP1110 A-23
To learn about the switching characteristics of an inductive proximity sensor.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 3
Switching distance of an inductive proximity sensor
Training aim
Exercise definition
Exercise 3
A-24 Festo Didactic GmbH & Co. FP1110
On an assembly station the presence of magazine shafts is monitored using
inductive sensors. Measure the switching distance of various inductive sensors in
order to determine the switching distance between a metal object and the sensor.
2
1
Inductive proximity switch (1), Magazine shaft (2)
Problem description
Positional sketch
Exercise 3
Festo Didactic GmbH & Co. FP1110 A-25
Inductive sensors contain an oscillator circuit, which consists of a parallel resonance
circuit with inductance and capacitance as well as an amplifier. By means of a ferrite
shell core of the inductance (coil), the electromagnetic field is directed towards the
outside.
If an electrically conductive material is introduced into the electromagnetic stray
field then, according to the laws of inductance, eddy currents are created, which
attenuate oscillation. Depending on the conductivity, the dimensions and the
distance of the approaching object, the oscillator can be attenuated to such an
extent that oscillation stops. Attenuation of the oscillator is evaluated via
subsequent electronic devices, and an output signal generated.
6
Oscillator (1), Demodulator (2), Triggering stage (3), Switching status
indicator (LED) (4), Output stage with protective circuit (5), External voltage (6),
Internal stabilised voltage (7), Active switching zone (coil) (8),
Switching output (9)
Function description
Exercise 3
A-26 Festo Didactic GmbH & Co. FP1110
1
3
4
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
4 1 Inductive sensor unit 2, D:ER-SIEH-M12B-...
1 Set of test objects, mild steel S 235 JR, part 3
Layout
Components list
Exercise 3
Festo Didactic GmbH & Co. FP1110 A-27
1
BN(1)
BU(3)
BK(4)
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
or
Inductive sensor unit 2, D:ER-SIEH-M12B-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 3
A-28 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the positioning slide and the inductive sensor unit 1
onto the profile plate. The inductive sensor is mounted centrally in front of the
middle of the positioning slide (see fig. "Layout"). Connect the 24V electrical power
supply and the inductive sensor to the distribution unit (see fig. "Electrical
connections").
Attach the vernier caliper to the positioning slide.
Now take the calibrating plate in mild steel (S 235 JR, part 3) from the set of test
objects and fit it into the material fixture of the positioning slide.
Measure the switching distance of the sensor. Make a note of the point, at which the
signal change occurs when the plate approaches the sensor, and also the point at
which the signal change occurs when you move the plate away from the sensor. The
difference between these two points is the hysteresis of the sensor.
Hysteresis (mm) = Switch-off point (mm) Switch-on point (mm)
Carry out the same measurements with the inductive sensor unit 2.
Repeat the measurements several times in order to check the reproducability of the
switching distance.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly 1
Practical assembly 2
Exercise 3
Festo Didactic GmbH & Co. FP1110 A-29
Inductive sensor unit 1 (D:ER-SIEH-M18B-...)
Switch-on point:
Switch-off point:
Hysteresis:
Inductive sensor unit 2 (D:ER-SIEH-M12B-...)
Switch-on point:
Switch-off point:
Hysteresis:
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 3
A-30 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-31
To learn that the switching distance of inductive proximity sensors is dependent on
materials when sensing different metals.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 4
Sensing of different metals with inductive proximity sensors
Training aim
Exercise definition
Exercise 4
A-32 Festo Didactic GmbH & Co. FP1110
On a conveyor, metal containers are used for the transport of assembly parts. The
position of the containers on the individual station is defined by means of an
inductive sensor. A selection of containers in different materials is available. The
effect of the different materials on the switching distance is to be examined.
Problem description
Positional sketch
Exercise 4
Festo Didactic GmbH & Co. FP1110 A-33
1
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
The components list is continued on the following page.
Layout
Components list
Exercise 4
A-34 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, part 3
1 Set of test objects, stainless steel, part 4
1 Set of test objects, aluminium, part 5
1 Set of test objects, brass, part 6
1 Set of test objects, copper, part 7
Components list
(continued)
Exercise 4
Festo Didactic GmbH & Co. FP1110 A-35
1
BN(1)
BU(3)
BK(4)
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 4
A-36 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the positioning slide and the inductive sensor unit 1 on
the profile plate. The inductive sensor is to be mounted centrally in front of the
positioning slide (see fig. "Layout"). Connect the 24V electrical power supply and
the inductive sensor to the distribution unit (see fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Measure the switching distance of the sensor for the different materials from the set
of test objects. Make a note of the point at which the change-over occurs, when the
plate approaches the sensor, as well as of the point of change-over when you move
the plate away from the sensor.
Take the mild steel plate (S 235 JR, part 3) from the set of test objects and fit it into
the material fixture of the positioning slide.
Take the various metal plates (stainless steel, aluminium, brass and copper) from
the set of test objects and carry out the measurements.
Determine the reduction factor of the switching distance for the different materials.
The reduction factor for mild steel (S 235 JR) is 1. With the other items, you can
obtain their respective value by dividing the determined switching distance by the
value of the switching distance for mild steel.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly
Exercise 4
Festo Didactic GmbH & Co. FP1110 A-37
Material Switch-on point
[mm]
Switc-off point
[mm]
Hysteresis
[mm]
Reduction factor
Mild steel
S 235 JR,
part 3
1
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 4
A-38 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-39
To learn about the influence of objects of different size on the switching distance of
an inductive proximity sensor.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 5
Influence of the object surface on the switching distance
Training aim
Exercise definition
Exercise 5
A-40 Festo Didactic GmbH & Co. FP1110
Metallic objects of different size must be detected on a rotary indexing table by an
inductive sensor. Only parts made from mild steel (S 235 JR) are to be detected.
Investigate the influence of the object size on the switching distance of the sensor.
Problem description
Positional sketch
Exercise 5
Festo Didactic GmbH & Co. FP1110 A-41
1
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
The components list is continued on the following page.
Layout
Components list
Exercise 5
A-42 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, 30 mm x 30 mm, part 11
1 Set of test objects, mild steel S 235 JR, 25 mm x 25 mm, part 12
1 Set of test objects, mild steel S 235 JR, 20 mm x 20 mm, part 13
1 Set of test objects, mild steel S 235 JR, 15 mm x 15 mm, part 14
1 Set of test objects, mild steel S 235 JR, 10 mm x 10 mm, part 15
1 Set of test objects, mild steel S 235 JR, 5 mm x 5 mm, part 16
Components list
(continued)
Exercise 5
Festo Didactic GmbH & Co. FP1110 A-43
1
BN(1)
BU(3)
BK(4)
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 5
A-44 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the positioning slide, and the inductive sensor unit 1 on
the profile plate. The inductive sensor should be mounted offset by 5 cm against the
centre of the positioning slide (see fig. "Layout"). Connect the 24V electrical power
supply and the inductive sensor to the distribution unit (see fig. "Electrical
connections").
Attach the vernier caliper to the positioning slide.
Take the mild steel plates of different length (parts 11 - 16) from the set of test
objects and carry out the measurements. Measure the switching distance of the
proximity sensor for each of the plates. Make a note of the measurements at which a
signal change occurs when the plates approach the sensor.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Note
The object of this exercise is to determine the relation between the switching
distance and the size of the object. Standard EN 50 010 specifies a standard
calibrating plate for defining the nominal switching distance. The standard
calibrating plate for an inductive sensor is 1 mm thick and has an edge length either
of the diameter of the inscribed circle of the active surface of the sensor or three
times the length of the nominal switching distance of the sensor, whichever value is
the larger.
For the sensor used, the nominal switching distance is 7 mm and the diameter of the
active surface 16 mm. The standard calibrating plate sides must thus have a length
of 21 mm.
Practical assembly
Exercise 5
Festo Didactic GmbH & Co. FP1110 A-45
Length of sides Switching gap [mm]
Mild steelS 235 JR,
part 11: 30 mm
Mild steel S 235 JR,
part 12: 25 mm
Mild steel S 235 JR,
part 13: 20 mm
Mild steel S 235 JR,
part 14: 15 mm
Mild steel S 235 JR,
part 15: 10 mm
Mild steel S 235 JR,
part 16: 5 mm
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 5
A-46 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-47
To learn about the response of a through-beam sensor and how to determine the
suitable materials for detection.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 6
Response characteristics of a through-beam sensor
Training aim
Exercise definition
Exercise 6
A-48 Festo Didactic GmbH & Co. FP1110
Two through-beam sensors are to be used for the loop control of a tape tensioning
installation. Different materials have to be detected. Examine the response of a
through-beam sensor to different materials.
Problem description
Positional sketch
Exercise 6
Festo Didactic GmbH & Co. FP1110 A-49
Optical sensors consist of two main parts, the emitter and the receiver. With
through-beam sensors, these are housed separately.
The emitter consists of light emitting diodes. They emit in the red or infra-red range
of wave length. This light is detected by means of suitable receivers. An object can
break the existing light connection between emitter and receiver. The object to be
detected should only let through a very small amount of the light beam, but may
reflect any amount of light.
3
Photoelectric emitter (1), Oscillator (pulse generator) (2), External voltage (3),
Internal stabilised voltage (4)
7
Photoelectric receiver (1), Preamplifier with potentiometer (2), Bandpass (filter) (3),
Pulse level converter (4), Switching status indicator (LED) (5), Output stage with
protective circuit (6), External voltage (7), Internal stabilised voltage (8), Switching
output (9)
Function description
Exercise 6
A-50 Festo Didactic GmbH & Co. FP1110
1
3
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit ESS, D:ER-SOE-S-Q-...
3 1 Optical sensor unit ESE, D:ER-SOE-E-Q-...
The components list is continued on the following page.
Layout
Components list
Exercise 6
Festo Didactic GmbH & Co. FP1110 A-51
Item no. Qty. Designation
1 Set of test objects, Kodak grey card, 100 mm x 100 mm, part 17
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
1 Set of test objects, cardboard, 90 mm x 30 mm, part 8
1 Set of test objects, pubber, 90 mm x 30 mm, part 9
1 Set of test objects, plastic, transparent, 90 mm x 30 mm, part 10
1 Graph paper pad, D:AS-RK
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 6
A-52 Festo Didactic GmbH & Co. FP1110
BN(1)
BN(1)
BU(3)
BU(3)
BK(4)
1
3
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit ESS, D:ER-SOE-S-Q-...
3 1 Optical sensor unit ESE, D:ER-SOE-E-Q-...
BN(1)
BU(3)
BK(4)
BN(1)
BU(3)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 6
Festo Didactic GmbH & Co. FP1110 A-53
Mount the distribution unit and the optical sensor units ESS and ESE (through-beam
sensor emitter and through-beam sensor receiver) on the profile plate. Select a
distance of 40 cm between the emitter and the receiver. Connect the 24V electrical
power supply and the emitter and the receiver to the distribution unit (see fig.
"Electrical connections"). Connect the normally open output (black safety plug) of
the receiver to a buzzer socket (see fig. "Electrical connections").
Examine the response to different materials: Set the adjustable potentiometer of the
through-beam sensor receiver at the maximum value (turn the screw clockwise, max.
12 revolutions). Guide the objects into the light beam of the through-beam sensor.
Enter your results in the table.
It may be necessary to adjust the potentiometer setting of the through-beam sensor
receiver, in order to achieve the detection of certain materials.
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Now test the response range of the through beam: Set the potentiometer at the
maximum value. Insert graph paper pad under the emitter. Guide the Kodak grey
card into the light beam from the side, with the white side facing the emitter, and
make a note of the switch-on points on the graph paper pad. Measure in gaps of
2 cm along the optical axis. Introduce the Kodak grey card alternatively from the
right and the left into the light beam.
Practical assembly
Exercise 6
A-54 Festo Didactic GmbH & Co. FP1110
Note
The emitter's black cable with black safety plug serves to simulate light beam
interruption. The emitter's light source is deactivated by applying a 24 V DC control
voltage to this plug.
When making your measurements, observe that the switch-on and switch-off points
of the proximity sensor do not coincide. Bring the Kodak grey card towards the
unactuated proximity sensor, e.g. from the left, until it changes its switching-on
state. In this way, you obtain the switching-on point. Now move the Kodak grey card
back to the left until the proximity sensor changes from the actuated to the
unactuated state, thus obtaining the switch-off point. The difference between these
two points is known as hysteresis.
Exercise 6
Festo Didactic GmbH & Co. FP1110 A-55
Material Detection yes/no
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Cardboard,
part 8
Rubber,
part 9
Plastic, transparent,
part 10
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 6
A-56 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-57
To learn about the range of applications and the response characteristics of a retro-
reflective sensor.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 7
Response characteristics of a retro-reflective sensor
Training aim
Exercise definition
Exercise 7
A-58 Festo Didactic GmbH & Co. FP1110
The gate to a yard is to be monitored by means of a retro-reflective sensor. Closure
of the gate is to be prevented, as long as an object is present in the opening. Find
out which objects can be detected by a retro-reflective sensor.
Problem description
Positional sketch
Exercise 7
Festo Didactic GmbH & Co. FP1110 A-59
Optical proximity sensors consist of two principal modules, the emitter and the
receiver. In the case of a retro-reflective sensor these two are mounted together in a
common housing. An additional reflector is required.
Normally, LEDs emitting light in the red or infra-red wave length range are used as
emitters. Suitable semi-conductor receivers detect this light inside the receiver
module. The object interrupts the existing light beam connection between emitter
and receiver. Reflecting objects can prevent this interruption.
9
Oscillator (1), Photoelectric emitter (2), Photoelectric receiver (3),
Preamplifier with potentiometer (4), AND connection (5), Pulse level converter (6),
Switching status indicator (LED) (7), Output stage with protective circuit (8),
External voltage (9), Internal stabilised voltage (10), Optical path (11),
Switching output (12)
Function description
Exercise 7
A-60 Festo Didactic GmbH & Co. FP1110
1
3
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit RS, D:ER-SOE-RS-Q-...
3 1 Reflector unit, D:ER-SOEZ-RFS20-...
The components list is continued on the following page.
Layout
Components list
Exercise 7
Festo Didactic GmbH & Co. FP1110 A-61
Item no. Qty. Designation
1 Set of test objects, Kodak grey card, 100 mm x 100 mm, part 17
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
Set of test objects, brass, 90 mm x 30 mm, part 6
Set of test objects, copper, 90 mm x 30 mm, part 7
1 Set of test objects, cardboard, 90 mm x 30 mm, part 8
1 Set of test objects, rubber, 90 mm x 30 mm, part 9
1 Set of test objects, plastic, transparent, 90 mm x 30 mm, part 10
1 Graph paper pad, D:AS-RK
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 7
A-62 Festo Didactic GmbH & Co. FP1110
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit RS, D:ER-SOE-RS-Q-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 7
Festo Didactic GmbH & Co. FP1110 A-63
Assemble the distribution unit and the optical sensor unit RS (retro-reflective
sensor). Use the reflector as reflecting element. The nominal switching distance for
this combination of units amounts to 1.5 m maximum. For your assembly, select a
distance of 0.4 m. Connect the 24V electrical power supply to the distribution unit
(see fig. "Electrical connections"). Connect the normally open output (black safety
plug) to a buzzer socket (see fig. Electrical connection).
Turn the adjustment potentiometer of the retro-reflective sensor to its maximum
value (turn the screw clockwise, max. 12 revolutions).
Introduce the different objects at a right angle into the path of the light beam and
note whether the objects are detected.
What happens when you want to detect mirror-like objects? How can this effect be
prevented? How do you position the object in relation to the retro-reflective sensor
so that mirroring objects can be reliably detected? How can the presence of
transparent objects be recorded under certain circumstances?
Now investigate the response range of the retro-reflective sensor: Reset the
potentiometer to the maximum value. Fix the graph paper pad underneath the
optical proximity sensor. From the side, introduce the Kodak grey card into the light
path, with the grey face pointing towards the emitter, and record the switch-on
points. Measure 2 cm distances along the optical axis. Introduce the card into the
light beam alternatively from the right and from the left.
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Practical assembly
Exercise 7
A-64 Festo Didactic GmbH & Co. FP1110
Exercise 7
Festo Didactic GmbH & Co. FP1110 A-65
Material Detection yes/no
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Cardboard,
part 8
Rubber,
part 9
Plastic, transparent,
part 10
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 7
A-66 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-67
To learn about the sensing range of a diffuse optical sensor depending on different
surfaces and how to record the response curve.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 8
Sensing range of a diffuse optical sensor
Training aim
Exercise definition
Exercise 8
A-68 Festo Didactic GmbH & Co. FP1110
In a sorting station, materials of different surface characteristics and of different
colours are to be detected by means of a diffuse sensor. Examine the switching
characteristics and the range of the various diffuse sensors.
Problem description
Positional sketch
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-69
Optical proximity sensors consist of two main parts, i.e. the emitter and the receiver.
In the case of diffuse sensors, these are installed in the same housing.
For the emitter, light emitting diodes are used, which emit mainly in the red or infra-
red range of wave length. This light is detected by the receiver via suitable
semiconductor receivers. The object thus reflects back a part of the emitted light and
activates the receiver. The object to be detected can be reflecting, matt, transparent
or opaque, provided a sufficiently high part of the light is reflected directly or by
diffusion.
9
Oscillator (1), Photoelectric emitter (2), Photoelectric receiver (3),
Preamplifier with potentiometer (4), AND connection (5), Pulse level converter (6),
Switching status indicator (LED) (7), Output stage with protective circuit (8),
External voltage (9), Internal stabilised voltage (10), Optical path (11),
Switching output (12)
Function description
Exercise 8
A-70 Festo Didactic GmbH & Co. FP1110
1
5
3
2
4
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
3 1 Optical sensor unit RT 1, D:ER-SOE-RT-Q-...
4 1 Optical sensor unit RT 2, D:ER-SOE-RT-M18-...
5 1 Measuring scale, D:AS-LIN-1020
The components list is continued on the following page.
Layout
Components list
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-71
Item no. Qty. Designation
1 Set of test objects, Kodak grey card, 100 mm x 100 mm, part 17
1 Set of test objects, plastic, transparent, 100 mm x 100 mm, part 18
1 Set of test objects, plastic, rot, 100 mm x 100 mm, part 19
1 Set of test objects, plastic, blau, 100 mm x 100 mm, part 20
1 Set of test objects, plastic, schwarz, 100 mm x 100 mm, part 21
1 Set of test objects, cardboard, wei, 100 mm x 100 mm, part 22
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
1 Set of test objects, brass, 90 mm x 30 mm, part 6
1 Set of test objects, copper, 90 mm x 30 mm, part 7
1 Set of test objects, rubber, 90 mm x 30 mm, part 9
1 Graph paper pad, D:AS-RK
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 8
A-72 Festo Didactic GmbH & Co. FP1110
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit RT 1, D:ER-SOE-RT-Q-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Experiment 1
Electrical circuit diagram
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-73
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit RT 2, D:ER-SOE-RT-M18-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Experiment 2
Electrical circuit diagram
Exercise 8
A-74 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the optical sensor unit RT 1 and the measuring scale on
to the profile plate (see fig. "Layout"). Connect the 24V electrical power supply and
the sensor to the distribution unit (see fig. "Electrical connections").
Calibrating the sensor
For your measurements, set the potentiometer of the diffuse optical sensor in such a
way that the white side of the Kodak grey card registers at a distance of
approximately 30 cm.
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Now put materials with different reflectivity in front of the sensor and determine the
switch-on point, the switch-off point and the hysteresis. The sliding part of the
positioning unit, which can be removed from the base plate, is used for holding the
materials. Use the measuring scale for lateral guiding and for measurement. Enter
your measurements in the table.
Re-assemble the positioning slide again when you have completed the exercise.
Note
With the coloured plastic parts 100 mm x 100 mm, the matted side has to face the
sensor.
To secure the rubber, part 9, use the mild steel plate as a clamping aid and support.
Practical assembly
Experiment 1
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-75
Now use the optical sensor unit RT 2. Mount the unit onto the aluminium bracket in
such a way that the front end is flush with the zero point of the scale.
Calibrating the sensor
With this sensor, set the potentiometer in such a way that the white side of the
Kodak grey card is registered at a distance of approximately 15 cm.
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Carry out the same measurements as in experiment 1. Enter the measured value in
the table.
Re-assemble the positioning slide again when you have completed the exercise.
Note
With the coloured plastic parts 100 mm x 100 mm, the matted side has to face the
sensor.
To secure the rubber, part 9, use the mild steel plate as a clamping aid and support.
Practical assembly
Experiment 2
Exercise 8
A-76 Festo Didactic GmbH & Co. FP1110
Now measure the response curves of the sensors. The potentiometer settings
remain unchanged. Clamp the graph paper pad together with each sensor onto the
assembly board.
Move the Kodak grey card, with the white side facing the sensor at a right angle, into
the detection area of the sensor and mark the point at which the sensor recognises
the card. Move the card closer from the right and from the left. Start your
measurements approximately 1 cm away from the sensor and measure in gaps of
approximately 2 cm.
Note
When carrying out your measurements, please note that the switch-on points and
switch-off points for the sensor do not coincide. Move the Kodak grey card towards
the unactuated sensor, e.g. from the left, until this changes its switching state, thus
obtaining the switch-on point. Now remove the Kodak grey card back towards the
left until the sensor changes from the actuated into the unactuated switching state,
thus obtaining the switch-off point. The difference between these two points is
known as hysteresis.
Practical assembly
Experiment 3
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-77
Experiment 1
Optical sensor unit RT 1 (D:ER-SOE-RT-Q-..)
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side,
part 17
Kodak grey card, grey side,
part 17
Plastic, transparent,
part 18
Plastic, red, matted side,
part 19
Plastic, blue, matted side,
part 20
Plastic, black, matted side,
part 21
Cardboard, white,
part 22
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Rubber,
part 9
Evaluation
Exercise 8
A-78 Festo Didactic GmbH & Co. FP1110
Experiment 2
Optical sensor unit RT 2 (D:ER-SOE-RT-M18-..)
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side,
part 17
Kodak grey card, grey side,
part 17
Plastic, transparent,
part 18
Plastic, red, matted side,
part 19
Plastic, blue, matted side,
part 20
Plastic, black, matted side,
part 21
Cardboard, white,
part 22
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Rubber,
part 9
Exercise 8
Festo Didactic GmbH & Co. FP1110 A-79
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Conclusions
Exercise 8
A-80 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-81
To learn about the fields of application and the sensing range of a diffuse sensor
equipped with a fibre-optic cable.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 9
Sensing range of a diffuse optical sensor with fibre-optic cable
Training aim
Exercise definition
Exercise 9
A-82 Festo Didactic GmbH & Co. FP1110
It is necessary to check the correct orientation of sealing caps fed from a vibrator
hopper. Restricted space conditions allow only sensors fitted with fibre-optic cables
to be used. Measure the sensitivity range of such an optical sensor.
1
2
Vibrator hopper (1), Fibre-optic cable, diffuse sensor design (2)
Problem description
Positional sketch
Exercise 9
Festo Didactic GmbH & Co. FP1110 A-83
1
4
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Optical sensor unit LL1, D:ER-SOE-L-Q-...
4 1 Fibre-optic cable unit RT, D:ER-SOEZ-LK-RT-...
The components list is continued on the following page.
Layout
Components list
Exercise 9
A-84 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Set of test objects, Kodak grey card, 100 mm x 100 mm, part 17
1 Set of test objects, pastic, transparent, 100 mm x 100 mm, part 18
1 Set of test objects, plastic, red, 100 mm x 100 mm, part 19
1 Set of test objects, plastic, blue, 100 mm x 100 mm, part 20
1 Set of test objects, plastic, black, 100 mm x 100 mm, part 21
1 Set of test objects, cardboard, white, 100 mm x 100 mm, part 22
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
1 Set of test objects, brass, 90 mm x 30 mm, part 6
1 Set of test objects, copper, 90 mm x 30 mm, part 7
1 Set of test objects, rubber, 90 mm x 30 mm, part 9
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 9
Festo Didactic GmbH & Co. FP1110 A-85
BN(1)
WH(2)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
BN(1)
BU(3)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 9
A-86 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit on the profile plate. Assemble the optical sensor unit
LL 1 (fibre-optic unit) with the fibre-optic cable unit RT. Insert the top part of the
fibre-optic cable into the fixture of the mounting bracket and position the mounting
bracket in front of the positioning slide. Mount the positioning slide 5 cm distant and
5 cm offset sideways (see fig."Layout"). Connect the 24 V power supply and the
proximity sensor to the distribution unit (see fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Investigate the sensing range of this combination of units. Fix each material in turn
to the positioning slide.
For the first measurement with the white side of the Kodak grey card, set the
potentiometer for maximum range (turn the screw clockwise, max. 12 revolutions).
Enter your results for the switch-on point, the switch-off point and the hysteresis in
the table.
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly
Exercise 9
Festo Didactic GmbH & Co. FP1110 A-87
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side,
part 17
Kodak grey card, grey side,
part 17
Plastic, transparent,
part 18
Plastic, red, matted side,
part 19
Plastic, blue, matted side,
part 20
Plastic, black, matted side,
part 21
Cardboard, white,
part 22
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Rubber,
part 9
Evaluation
Exercise 9
A-88 Festo Didactic GmbH & Co. FP1110
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Conclusions
Festo Didactic GmbH & Co. FP1110 A-89
To learn about the switching characteristics of capacitive sensors.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 10
Switching distance of a capacitive sensor
Training aim
Exercise definition
Exercise 10
A-90 Festo Didactic GmbH & Co. FP1110
The presence of cardboard boxes in a packaging machine is to be monitored. A
capacitive sensor is to be used for detection. Investigate whether this is suited for
the purpose. In order to establish whether it would also be suitable for other
packaging materials, you are asked to determine the switching distance for various
materials.
Problem description
Positional sketch
Exercise 10
Festo Didactic GmbH & Co. FP1110 A-91
The operational principle of a capacitive proximity sensor is based on the capacitive
change of a condenser in an RC resonant circuit, formed by a condenser (C) and a
resistance (R).
If a substance is made to approach the proximity sensor, the capacity of the
condensor increases. This causes a measurable change in the oscillatory
characteristics of the RC circuit. Such change is converted by electronic evaluating
circuitry into a usable output signal. The change in capacity depends largely on
distance, dimensions and the dielectric constant of the substance in question.
6
Oscillator (1), Demodulator (2), Triggering stage (3), Switching status indicator (4),
Output stage with protective circuit (5), External voltage (6), Internal stabilised
voltage (7), Active switching zone (condensor) (8), Switching output (9)
Function description
Exercise 10
A-92 Festo Didactic GmbH & Co. FP1110
1
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Capacitive sensor unit, D:ER-SKE-M12-...
The components list is continued on the following page.
Layout
Components list
Exercise 10
Festo Didactic GmbH & Co. FP1110 A-93
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
1 Set of test objects, brass, 90 mm x 30 mm, part 6
1 Set of test objects, copper, 90 mm x 30 mm, part 7
1 Set of test objects, cardboard, 90 mm x 30 mm, part 8
1 Set of test objects, rubber, 90 mm x 30 mm, part 9
1 Set of test objects, plastic, transparent, 90 mm x 30 mm, part 10
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 10
A-94 Festo Didactic GmbH & Co. FP1110
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Capacitive sensor unit, D:ER-SKE-M12-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 10
Festo Didactic GmbH & Co. FP1110 A-95
Mount the distribution unit on the profile plate and also assemble the capacitive
sensor unit. Mount the positioning slide offset sideways by 5 cm in relation to the
sensor (see fig. "Layout"). Connect the 24V power supply and the sensor to the
distribution unit (see fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Using the mild steel plate, part 3, set the switching distance of the proximity sensor
at 8 mm via the adjusting screw. Carry out the switching distance measurement for
the various test object materials. Enter your results for switch-on and switch-off
point in a table. Calculate the hysteresis as the difference between switch-off and
switch-on point and enter this likewise in the table.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Note
The capacitive proximity switch utilised is suitable only for non-flush mounting. This
means that the active surface must not be surrounded by a material which leads to a
change of switching status. There is no procedure laid down in a standard
prescribing how to establish the switching distance.
Practical assembly
Exercise 10
A-96 Festo Didactic GmbH & Co. FP1110
Exercise 10
Festo Didactic GmbH & Co. FP1110 A-97
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Cardboard,
part 8
Rubber,
part 9
Plastic, transparent,
part 10
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 10
A-98 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-99
To learn about the effect of the material thickness on the switching distance of a
capacitive sensor.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 11
Influence of material thickness on the switching distance of a capacitive sensor
Training aim
Exercise definition
Exercise 11
A-100 Festo Didactic GmbH & Co. FP1110
On a conveyor, plastic parts of varying thickness are to be detected. A capacitive
sensor is used for detection. Examine the effect of the material thickness on the
switching distance of a sensor.
Problem description
Positional sketch
Exercise 11
Festo Didactic GmbH & Co. FP1110 A-101
1
3
2
10 20 30 40 50 10 0 20 30 50 60 70 80 90 100
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
1 Vernier caliper, D:AS-MS
3 1 Capacitive sensor unit, D:ER-SKE-M12-...
The components list is continued on the following page.
Layout
Components list
Exercise 11
A-102 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, plastic, 2 mm thick, part 23
1 Set of test objects, plastic, 3 mm thick, part 24
1 Set of test objects, plastic, 5 mm thick, part 25
1 Set of test objects, plastic, 8 mm thick, part 26
1 Set of test objects, plastic, 11 mm thick, part 27
1 Set of test objects, plastic, 14 mm thick, part 28
1 Set of test objects, plastic, 17 mm thick, part 29
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 11
Festo Didactic GmbH & Co. FP1110 A-103
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Capacitive sensor unit, D:ER-SKE-M12-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 11
A-104 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit on the profile plate and also the capacitive sensor unit.
Then mount the positioning slide 5 cm to the side of the sensor (see fig. "Layout").
Connect the 24V electrical power supply and the sensor to the distribution unit (see
fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Next, use the mild steel plate, part 3, and set the switching distance at 8 mm. Then
take the plastic plates of varying thicknesses from the set of test objects (parts 23 to
29) and determine the switching distance. Enter the measuring points in a table and
draw a graph showing the switching distance depending on material thickness.
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly
Exercise 11
Festo Didactic GmbH & Co. FP1110 A-105
Material thickness [mm] Switching distance [mm]
Plastic,
part 23, 2.0 mm thick
Plastic,
part 24, 3.0 mm thick
Plastic,
part 25, 5.0 mm thick
Plastic,
part 26, 8.0 mm thick
Plastic,
part 27, 11.0 mm thick
Plastic,
part 28, 14.0 mm thick
Plastic,
part 29, 17.0 mm thick
S
w
i
t
c
h
i
n
g
d
i
s
t
a
n
c
e
Material thickness
0
1
2
3
5
4
mm
0 mm 14 12 10 8 6 4 2 1 3 5 7 9 11 13 15 17
Evaluation
Exercise 11
A-106 Festo Didactic GmbH & Co. FP1110
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Conclusions
Festo Didactic GmbH & Co. FP1110 A-107
To determine the reflection characteristics and the response curve of an ultrasonic
proximity sensor. Possibilities of application are investigated with the help of
different materials.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 12
Sound wave form and reflection characteristics of an ultrasonic sensor
Training aim
Exercise definition
Exercise 12
A-108 Festo Didactic GmbH & Co. FP1110
When producing film and foil, the winding of transparent plastic film and of thin
metal foil is to be monitored by means of a proximity sensor. Investigate whether an
ultrasonic proximity sensor is suitable for this purpose.
Problem description
Positional sketch
Exercise 12
Festo Didactic GmbH & Co. FP1110 A-109
The operational principle of an ultrasonic proximity sensor is based on the
generation, emission, and reception of sound waves in the non-audible range,
mostly between 30 and 300 kHz.
The ultrasonic proximity sensor is built up from three principal modules, the
ultrasonic transducer, the evaluation unit, and the output stage. The ultrasonic
transducer is usually a piezo-electric module, which is excited to generate vibrations
in the range of 30 to 300 kHz by the application of a sinusoidal voltage.
The ultrasonic pulses are emitted with a frequency of between 1 Hz and 100 Hz. An
evaluation is made of the time between the emission of an ultrasonic pulse and the
reception of the pulse reflected by an object. If the object is located within the
switching range of the ultrasonic sensor, an output signal is emitted.
6
Oscillator (1), Evaluation unit (2), Triggering stage (3), Switching status indicator (4),
Output stage with protective circuit (5), External voltage (6), Internal stabilised
voltage (7), Active switching zone (ultrasonic transducer) (8), Switching output (9)
Function description
Exercise 12
A-110 Festo Didactic GmbH & Co. FP1110
1
4
2
3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
3 1 Sensor unit ultrasonic, D:ER-SUE-M18-...
4 1 Measuring scale, D:AS-LIN-1020
The components list is continued on the following page.
Layout
Components list
Exercise 12
Festo Didactic GmbH & Co. FP1110 A-111
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, stainless steel, 90 mm x 30 mm, part 4
1 Set of test objects, aluminium, 90 mm x 30 mm, part 5
1 Set of test objects, brass, 90 mm x 30 mm, part 6
1 Set of test objects, copper, 90 mm x 30 mm, part 7
1 Set of test objects, cardboard, 90 mm x 30 mm, part 8
1 Set of test objects, rubber, 90 mm x 30 mm, part 9
1 Set of test objects, plastic, transparent, 90 mm x 30 mm, part 10
1 Set of test objects, plastic, transparent, 100 mm x 100 mm, part 18
1 Graph paper pad, D:AS-RK
Components list
(continued)
Exercise 12
A-112 Festo Didactic GmbH & Co. FP1110
BN(1)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Sensor unit ultrasonic, D:ER-SUE-M18-...
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 12
Festo Didactic GmbH & Co. FP1110 A-113
Attach the distribution unit, the ultrasonic sensor unit and the measuring scale to
the profile plate (see fig. "Layout"). Connect the 24V power supply and the
proximity sensor to the distribution unit (see fig. "Electrical connections").
Introduce the various test objects into the path of emission at a distance of 15 cm
and note whether and under what conditions these are detected. Use the separate
sliding part of the positioning slide for mounting the objects, with the measuring
scale as a lateral stop. Check the dependence of the sound reflection on the angle by
means of the rotatable head of the sliding part.
Fix the graph paper pad under the base of the proximity switch. Take the transparent
plastic plate 100 mm x 100 mm, part 18, of the set of test objects, move it from the
side (from the left and from the right) into the ultrasonic beam. Keep the plastic
plate perpendicular to the ultrasonic beam axis. On the graph paper, mark the
points, at which the ultrasonic sensor detects them (leading edge of the plate). Start
your measurements 5 cm distant from the sensor and measure in steps of 2 cm.
Re-assemble the positioning slide again when you have completed the exercise.
Note
Observe that the switch-on and switch-off points of the sensor do not coincide when
you take your measurements. For instance, let the plastic plate approach the
inactive proximity sensor from the left until this changes its switching status, thus
obtaining its switch-on point. Then move away the plastic plate towards the left until
the proximity sensor changes from the active to the inactive state, thus obtaining its
switch-off point. The distance travelled between these two points is described as
hysteresis.
Practical assembly
Exercise 12
A-114 Festo Didactic GmbH & Co. FP1110
Hold a flat metal plate (from the set of test objects, e.g. the stainless steel plate)
10 cm distant from the proximity sensor and deflect the beam by 90. Use the
positioning slide and clamp a metal plate into the retaining fixture. Then turn it by
45. Can you now detect a second metal plate (also from the set of test objects) with
the deflected beam (see figure below)?
1
2
Part 1 (e.g. stainless steel plate) (1), Part 2 (e.g. copper plate) (2)
Exercise 12
Festo Didactic GmbH & Co. FP1110 A-115
Material Detection yes/no
Mild steel S 235 JR,
part 3
Stainless steel,
part 4
Aluminium,
part 5
Brass,
part 6
Copper,
part 7
Cardboard,
part 8
Rubber,
part 9
Plastic,
transparent, part 10
Plastic,
transparent, part 18
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 12
A-116 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-117
To learn about the use of optical proximity sensors with fibre-optic cables for the
measurement of speed.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 13
Speed measurement
Training aim
Exercise definition
Exercise 13
A-118 Festo Didactic GmbH & Co. FP1110
On a conveyor, the speed of certain passing components is to be checked. Space for
installing the sensors is restricted. Therefore, a sensor with fibre-optic cables is to
be used.
Problem description
Positional sketch
Exercise 13
Festo Didactic GmbH & Co. FP1110 A-119
1
3
4
1
0
2
0
3
0
4
0
5
0
1
0
0
2
0
3
0
5
0
6
0
7
0
8
0
9
0
1
0
0
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP111-...0
1 Vernier caliper, D:AS-MS
3 1 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
4 1 Fibre-optic cable unit SE, D:ER-SOEZ-LK-SE-...
1 Set of test objects, holder for fibre-optic cable, part 30
1 Set of test objects, screw driver, part 36
Layout 1
Components list
Exercise 13
A-120 Festo Didactic GmbH & Co. FP1110
BN(1)
BK(4)
BU(3)
WH(2)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
BN(1)
BU(3)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 13
Festo Didactic GmbH & Co. FP1110 A-121
1
3
2
4
START STOP RESET
CLOCK
1000 100
Imp./s
Im p./s
Im p.
Im p./s
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Counting unit, D:ER-ZE-FP1110-...
3 2 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
4 2 Fibre-optic cable unit SE, D:ER-SOEZ-LK-SE-...
Layout 2
Components list
Exercise 13
A-122 Festo Didactic GmbH & Co. FP1110
3
2 1
START STOP RESET
CLOCK
1000 100
Imp./s
I mp./s
I mp.
I mp./s
BN(1)
BK(4)
BU(3)
WH(2)
BN(1)
BK(4)
BU(3)
WH(2)
3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Counting unit, D:ER-ZE-FP1110-...
3 2 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
+24 V DC
0 V
BN(1)
BU(3)
BN(1)
BU(3)
BN(1)
BU(3)
Electrical connections
Electrical circuit diagram
Exercise 13
Festo Didactic GmbH & Co. FP1110 A-123
First of all, determine the maximum switching distance of the optical sensor
unit LL 1. Mount the distribution unit, the positioning slide, and an optical sensor
unit LL 1 on the profile plate (see fig. "Practical assembly 1"). Connect the 24V
electrical power supply and the optical sensor unit LL 1 to the distribution unit (see
fig. "Electrical connections").
Attach the vernier caliper to the positioning slide.
Set the potentiometer on the optical sensor unit LL 1 at maximum sensitivity (turn
the screw clockwise, max. 12 revolutions).
Install the fibre-optic cable unit ES on the optical sensor unit LL1.
Screw one of the fibre-optic cables into its holder and mount it centrally 15 cm in
front of the positioning slide. Secure the other fibre-optic cable in the material
fixture of the positioning slide with the help of the holder for fibre-optic cables (set
of test objects, part 30)
Move the receiver fibre-optic cable towards the emitter fibre-optic cable and make a
note of the distance, at which the light emitting diode registers the change of the
sensor switching state.
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Practical assembly
Experiment 1
Exercise 13
A-124 Festo Didactic GmbH & Co. FP1110
Now choose a speed measuring distance of 10 cm. The distance between the emitter
and the receiver fibre-optic cable should be 5 cm (see "Practical assembly 2"). Use
the two optical sensor units LL 1 and the two fibre-optic cables ES. Connect these
combined sensor units on the distribution unit (see fig. "Electrical connections").
The normally closed contact of the sensor is to be used in order to prevent a
permanent signal from the distribution unit during the unactuated state. An output
pulse should only be given when the object passes through the light beam.
Connect the counting unit to the distribution unit. Set the display mode switch 1 to
'Pulse' (Imp.). Connect the first light barrier to START socket 2 and the second to
STOP socket 3. Use a short cable with safety plugs to connect the CLOCK socket 4
with the pulse output 10 '1000 Imp/s'.
Preparing the counting unit for measurement
Press the "Stop", "Reset" and "Start" buttons before the first measurement, in
order to prepare the counting unit for measurement.
Now move an object (plate from set of test objects or your finger) through the
barriers.
To determine the speed v:
v = s / t
s = 0.1 m
t = (Display / 1000) s
s = path
t = time
Practical assembly
Experiment 2
Exercise 13
Festo Didactic GmbH & Co. FP1110 A-125
Switching distance
Potentiometer at maximum setting
Switch-on distance
Switch-off distance
Hysteresis
Speed measurement
Indicated value
Corresponding time [s]
Path [m]
Speed [m/s]
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 13
A-126 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-127
To learn about the differences and the application criteria of rotational speed
detection with optical and inductive proximity sensors.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 14
Determining rotational speeds
Training aim
Exercise definition
Exercise 14
A-128 Festo Didactic GmbH & Co. FP1110
In certain parts of a building a low pressure is to be permanently maintained. The
monitoring of the speed of ventilator fans in a ventilating plant is carried out by
means of sensors.
Problem description
Positional sketch
Exercise 14
Festo Didactic GmbH & Co. FP1110 A-129
1
3
2
7
START STOP RESET
CLOCK
1000 100
Imp./s
Im p./s
Im p.
Im p./s
8
+
+24V 0V
1
0
2
0
3
0
4
0
5
0
1
0
0
2
0
3
0
5
0
6
0
7
0
8
0
9
0
1
0
0
5
6
4
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Counting unit, D:ER-ZE-FP1110-...
3 1 Rotary unit, D:ER-DE-FP1110-...
1 Digital multimeter, D:AS-DMM
4 1 Set of test objects, holder for fibre-optic cable, part 30
5 1 Inductive sensor unit 2, D:ER-SIEH-M12B-...
6 1 Positioning slide, D:ER-VS-FP1110-...
The components list is continued on the following page.
Layout
Components list
Exercise 14
A-130 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Vernier caliper, D:AS-MS
7 1 Fibre-optic cable unit RT, D:ER-SOEZ-LK-RT-...
8 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
1 Set of test objects, screw driver, part 36
1 17 mm spanner
4 2
2
5
1
START STOP RESET
CLOCK
1000 100
Imp./s
Imp./s
Imp.
I mp./s
BN(1)
WH(2)
BU(3)
BK(4)
BN(1)
BU(3)
BK(4)
+
+
2
4
V
0
V
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Counting unit, D:ER-ZE-FP1110-...
3 1 Rotary unit, D:ER-DE-FP1110-...
4 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
5 1 Inductive sensor unit 2, D:ER-SIEH-M12B-...
Components list
(continued)
Electrical connections
Exercise 14
Festo Didactic GmbH & Co. FP1110 A-131
+24 V DC
0 V
BN(1) BN(1)
BU(3) BU(3)
BN(1)
BU(3)
BN(1)
BU(3)
M
Electrical circuit diagram
Exercise 14
A-132 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the rotary unit, the counting unit, and the positioning
slide on the profile plate. Connect the rotary and the counting unit to the distribution
unit. Mount the fibre-optic cable unit RT with the optical sensor unit LL 1 (Fibre-optic
unit) on the reflector side of the rotary unit, and the inductive sensor unit 2 on the
positioning slide. These sensors must also be connected to the distribution unit.
Connect the 24V electrical power supply to the distribution unit.
Attach the vernier caliper to the positioning slide.
Adjusting the optical sensor D:ER-SOE-L-Q-...
The threaded part of the fibre-optic cable unit RT is fastened in the mounting hole on
the right-hand side of the rotary unit's mountingbracket. Both ends of the fibre-optic
cable are attached to the fibre-optic unit.
The potentiometer of the optical sensor unit LL 1 has to be set carefully for the
sensor to switch reliably if the perforated disk is turned by hand. With the rotary unit
at maximum speed, the potentiometer setting must be carefully adjusted until the
position is discovered at which maximum rotational frequency is displayed at the
connected counting unit (display within a range of approx. 520 Hz to 630 Hz).
Note
For reliable operation, the green LED (function reserve indicator) must light up as
well as the yellow LED (switching status indicator), when the sensor is detecting an
object.
Adjusting the inductive sensor D:ER-SIEH-M12B-...
The sensor included in the inductive sensor unit 2 must be removed from the
retainer, and mounted to the holder for fibre-optic cables (set of test objects, part
30). Attach the mounted sensor to the material retainer of the positioning slide. A
distance of approx. 3 mm between the perforated disc and the sensor should be
used at first (set of test objects, plastic, part 23).
The speed of the rotary unit should be set with the help of the adjusted optical
sensor such that a value of approximarely 200 Hz appears at the display. The
inductive sensor must now be adjusted such that it measures the same value (i.e.
approx. 200 Hz).
Practical assembly
Exercise 14
Festo Didactic GmbH & Co. FP1110 A-133
Mounting the vernier caliper
When mounting the vernier caliper, the slide unit of the positioning slide is set at
"0". The two measuring pointers are moved apart by approximately 10 mm. The
vernier caliper is placed parallel to the base plate, flush with the edge, so that the
front pointer is adjacent to the stop for the vernier caliper. The body of the caliper is
attached to the base plate of the positioning slide by means of the two retaining
magnets.
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Preparing the counting unit for measurement
Press the "Stop", "Reset" and "Start" buttons before the first measurement, in
order to prepare the counting unit for measurement.
Connecting the sensors for measurement
The switching output of the optical or the inductive proximity sensor is now
connected to the clock socket 4 at the counting unit. Display switch 1 is set to
"Imp/s". Press the "Start" button. The current value of the output signals per
second of the proximity sensor are displayed once per second.
Exercise 14
A-134 Festo Didactic GmbH & Co. FP1110
Speed RS is determined thus:
. m . p . r
n
60
s / pulses
f
RS
s
f
s
: Pulse frequency of output signal (unit: pulses per second)
n : Number of actuations per rotation
When using the rotary unit, n equals 8.
Note
The motor starts with a speed of approximately 2500 r.p.m. as soon as the operating
voltage is switched on.
Let the motor run at low speed by pressing the touch control near the blue socket
and watch the display. When the inductive sensor attains a value of approximately
200 pulses/s, check the potentiometer setting of the optical sensor, which should
display the same value.
Start your series of measurements when the display reads approximately
80 pulses/sec. The operating voltage of the motor is then approximately 4.0 Volts.
Measure the operating voltage of the motor and enter the value in the table. To
measure the operating voltage connect the digital multimeter (D.AS-DMM) to the
two black sockets of the rotary unit. Select the operating mode "Voltage
Measurement" and a measuring range of at least 30 Volts. Start your measurement
at a voltage of 4.0 Volts and increase the operating voltage initially by approximately
0.5 Volts, and after 14 Volts by 1.0 Volt at a time. After each measurement with the
optical sensor, connect the inductive sensor and measure the speed with this
sensor.
Enter each of the measured values in the table. Calculate the value for the speed
from the value of the highest output pulse frequency and enter this in the right-hand
column.
What are your findings about the switching frequency of the sensors?
Exercise 14
Festo Didactic GmbH & Co. FP1110 A-135
Motor voltage [V] Output-pulse-
frequency
SOE-L-Q-...
[pulses/s]
Output-pulse-
frequency
SIEH-M12B-...
[pulses/s]
Speed RS [r.p.m.]
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
15.0
16.0
17.0
18.0
19.0
20.0
Evaluation
Exercise 14
A-136 Festo Didactic GmbH & Co. FP1110
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Conclusions
Festo Didactic GmbH & Co. FP1110 A-137
To learn about the application of proximity sensors for the checking of workpieces.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 15
Sensing the correct assembly of workpieces
Training aim
Exercise definition
Exercise 15
A-138 Festo Didactic GmbH & Co. FP1110
Pre-assembled components are transported on a conveyor. The correct assembly of
the components is to be checked. A diffuse sensor is used to check whether a gear
wheel has been mounted in the correct position.
Problem description
Positional sketch
Exercise 15
Festo Didactic GmbH & Co. FP1110 A-139
1
3
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
3 1 Fibre-optic cable unit RT, D:ER-SOEZ-LK-RT-...
1 Set of test objects, base plate with gear wheels, part 31
1 Graph paper pad, D:AS-RK
1 Set of test objects, screw driver, part 36
Layout
Components list
Exercise 15
A-140 Festo Didactic GmbH & Co. FP1110
BN(1)
WH(2)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
BN(1)
BU(3)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 15
Festo Didactic GmbH & Co. FP1110 A-141
Mount the distribution unit and the optical sensor unit LL 1 with the fibre-optic cable
unit RT on the profile plate. During assembly, clamp the graph paper pad (see fig.
"Layout") under the holder of the fibre-optic cable. Connect the 24V power supply
and the sensor to the distribution unit (see fig. "Electrical connections").
Turn the potentiometer of the sensor unit to maximum range (turn the screw
clockwise, max. 12 revolutions). Move the sub-base and the gear wheel separately
towards the sensor from different directions and make a note of the distances, at
which the object is detected. You can read the distances from the graph paper.
The optical sensor cannot detect the base plate at a distance of 20 mm. Now mount
the large gear wheel with the open side facing towards the fibre-optic cable unit.
Does the sensor recognise it?
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Practical assembly
Exercise 15
A-142 Festo Didactic GmbH & Co. FP1110
Exercise 15
Festo Didactic GmbH & Co. FP1110 A-143
Object Switching distance [mm]
Base plate
Gear wheel
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 15
A-144 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-145
To learn about the possibilities of using capacitive and optical sensors for measuring
liquid levels.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 16
Liquid level measurement
Training aim
Exercise definition
Exercise 16
A-146 Festo Didactic GmbH & Co. FP1110
The liquid level inside a transparent plastic container is to be ascertained through
the wall of the container. For technical reasons, it is not possible to fit the sensor
inside the container. Investigate the possibilities of using capacitive and optical
proximity sensors.
Problem description
Positional sketch
Exercise 16
Festo Didactic GmbH & Co. FP1110 A-147
1
2 3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Capacitive sensor unit, D:ER-SKE-M12-...
3 1 Set of test objects, beaker, part 33
1 Set of test objects, screw driver, part 36
Layout 1
Components list
Exercise 16
A-148 Festo Didactic GmbH & Co. FP1110
1
3
2
4
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit ESS, D:ER-SOE-S-Q-...
3 1 Optical sensor unit ESE, D:ER-SOE-E-Q-...
2 Set of test objects, holding bracket for liquid level measurement,
part 32
4 1 Set of test objects, beaker, part 33
1 Screw driver
1 Allen key
Layout 2
Components list
Exercise 16
Festo Didactic GmbH & Co. FP1110 A-149
1
3
2
4
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
3 1 Fibre-optic cable unit RT, D:ER-SOEZ-LK-RT-...
4 1 Set of test objects, beaker, part 33
1 Set of test objects, screw driver, part 36
Layout 3
Components list
Exercise 16
A-150 Festo Didactic GmbH & Co. FP1110
BN(1)
BU(3)
BK(4)
1
2
3
4
5
BN(1)
BN(1)
BU(3)
BU(3)
BK(4)
BN(1)
WH(2)
BU(3)
BK(4)
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Capacitive sensor unit, D:ER-SKE-M12-...
3 1 Optical sensor unit ESS, D:ER-SOE-S-Q-...
4 1 Optical sensor unit ESE, D:ER-SOE-E-Q-...
5 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
Electrical connections
Components list
Exercise 16
Festo Didactic GmbH & Co. FP1110 A-151
BN(1)
BU(3)
BK(4)
+24 V DC
0 V
BN(1)
BU(3)
BK(4)
BN(1)
BU(3)
BN(1)
BU(3)
1
2 3 4
Item no. Qty. Designation
1 1 Capacitive sensor unit, D:ER-SKE-M12-...
2 1 Optical sensor unit ESS, D:ER-SOE-S-Q-...
3 1 Optical sensor unit ESE, D:ER-SOE-E-Q-...
4 1 Optical sensor unit LL 1, D:ER-SOE-L-Q-...
Electrical circuit diagram
Components list
Exercise 16
A-152 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit and the capacitive sensor on the profile plate (see fig.
"Layout 1"). Connect the 24V electrical power supply to the distribution unit (see
fig. "Electrical connections").
Take the beaker and place it close to and in front of the active surface of the
capacitive sensor. Connect the capacitive sensor to the distribution unit.
Using the potentiometer screw, adjust the sensitivity of the sensor to such a degree
that it cannot detect the wall of the beaker. Slowly fill the beaker with water and
observe the sensor's LED indicator.
Capacitive sensor unit
Locate beaker directly at PS
*)
water level
__ mm, PS switches on
__ mm, PS switches off
Locate beaker 3 mm from PS
*)
water level
__ mm, PS switches on
__ mm, PS switches off
*)
PS = Proximity sensor
Note
It is possible, in a similar manner, to detect objects through walls with the capacitive
sensor (e.g. metallic objects through plastic partitions).
Practical assembly
Experiment 1
Evaluation
Exercise 16
Festo Didactic GmbH & Co. FP1110 A-153
Liquid level measurement with optical sensor ESS/ESE is also possible.
Use the holding bracket (set of test objects, part 32). Mount this between aluminium
bracket and proximity sensor so that the two sensors are inclined by an angle of 20.
Mount the sensor at a distance of 10 cm on the profile plate (see fig. "Layout 2").
Connect the 24V electrical power supply and the two optical sensor units to the
distribution unit (see fig. "Electrical connections).
1
3
2
Optical sensor unit ESS or optical sensor unit ESE (1); Set of test objects, holding
bracket for liquid level measurement, part 32 (2); Aluminium bracket (3)
Introduce the beaker between the elements of the through-beam sensor. Slowly fill
it with water and watch the switching status indicator. Here, too, investigate the
accuracy of liquid level monitoring.
Through-beam sensor
Beaker placed between emitter and receiver
water level __ mm on
with further filling __ mm off
Note
This arrangement is capable also of roughly detecting the height of objects.
Practical assembly
Experiment 2
Evaluation
Exercise 16
A-154 Festo Didactic GmbH & Co. FP1110
With optical sensor unit LL 1 and with fibre-optic cable unit RT it is likewise possible
to measure liquid levels.
Mount the sensor on the profile plate (see fig. "Layout 3"). Connect it to the
distribution unit.
Adjust the sensor's potentiometer for maximum range (turn the screw clockwise,
max. 12 revolutions). Bring the holder with fibre-optic cable unit RT above the filled
beaker and watch for indication of switching status. Investigate the accuracy with
which it is possible to detect a liquid level (hysteresis).
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Diffuse sensor with fibre-optic cable
Distance PS
*)
water level __ mm on
Distance PS
*)
water level __ mm off
*)
PS = Proximity sensor
Practical assembly
Experiment 3
Evaluation
Festo Didactic GmbH & Co. FP1110 A-155
To learn about the use of optical proximity sensors with fibre-optic cables for
checking threads.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 17
Checking of threads
Training aim
Exercise definition
Exercise 17
A-156 Festo Didactic GmbH & Co. FP1110
During production, screws are to be checked for thread with an optical sensor. Problem description
Positional sketch
Exercise 17
Festo Didactic GmbH & Co. FP1110 A-157
1
4
3
5
2
1
0
2
0
3
0
4
0
5
0
1
0
0
2
0
3
0
5
0
6
0
7
0
8
0
9
0
1
0
0
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Positioning slide, D:ER-VS-FP1110-...
3 1 Optical sensor unit LL1, D:ER-SOE-L-Q-...
4 1 Fibre-optic cable unit RT, D:ER-SOEZ-LK-RT-...
5 1 Set of test objects, holder for fibre-optic cables, part 30
1 Set of test objects, 2 screws, part 34
1 Set of test objects, screw driver, part 36
Layout
Components list
Exercise 17
A-158 Festo Didactic GmbH & Co. FP1110
BN(1)
WH(2)
BU(3)
BK(4)
1
2
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Optical sensor unit LL1, D:ER-SOE-L-Q-...
BN(1)
BU(3)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 17
Festo Didactic GmbH & Co. FP1110 A-159
Mount the distribution unit and the optical sensor unit LL 1 with the fibre-optic cable
unit RT on the profile plate. Connect the 24V power supply and the sensor to the
distribution unit (see fig. "Electrical connections").
Check the response to the test screws provided. Clamp the screw into the slide unit
at an angle of 45. Mount the screws one after the other into the holder for the fibre-
optic cable (set of test objects, part 30). Move the screw in front of the sensing head
of the fibre-optic cable, first with the thread facing the sensing head and then with
the plain shank.
Enter the results of your measurements in the table. Sketch the lightbeam, which
leads to the detection of the thread and the lightbeam which results in the bolt not
being recognised.
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Practical assembly
Exercise 17
A-160 Festo Didactic GmbH & Co. FP1110
Exercise 17
Festo Didactic GmbH & Co. FP1110 A-161
Mark the correct response
a) Threaded screw recognised / not recognised
b) Plain screw recognised / not recognised
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 17
A-162 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 A-163
To learn how to establish logic connections with proximity sensors.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 18
Logic combinations of proximity sensor signals
Training aim
Exercise definition
Exercise 18
A-164 Festo Didactic GmbH & Co. FP1110
In a pressing operation, metal inserts are pressed into plastic parts. Monitoring of
material supply is carried out by means of a combination of sensors. The press is to
operate only when the plastic part as well as the metal insert are in the correct
position.
Problem description
Positional sketch
Exercise 18
Festo Didactic GmbH & Co. FP1110 A-165
1
2
3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
3 1 Capacitive sensor unit, D:ER-SKE-M12-...
1 Digital multimeter, D:AS-DMM
The components list is continued on the following page.
Layout
Components list
Exercise 18
A-166 Festo Didactic GmbH & Co. FP1110
Item no. Qty. Designation
1 Set of test objects, mild steel S 235 JR, 90 mm x 30 mm, part 3
1 Set of test objects, cardboard, 90 mm x 30 mm, part 8
1 Set of test objects, screw driver, part 36
Components list
(continued)
Exercise 18
Festo Didactic GmbH & Co. FP1110 A-167
BN(1)
BU(3)
BK(4)
2
1
BN(1)
BU(3)
BK(4)
3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Inductive sensor unit 1, D:ER-SIEH-M18B-...
3 1 Capacitive sensor unit, D:ER-SKE-M12-...
BN(1) BN(1)
BU(3) BU(3)
BK(4) BK(4)
+24 V DC
0 V
Electrical connections
Electrical circuit diagram
Exercise 18
A-168 Festo Didactic GmbH & Co. FP1110
Mount the distribution unit, the inductive sensor unit 1 and the capacitive sensor
unit on the profile plate. Connect the 24V power supply to the distribution unit.
Measure the current consumption of the various proximity sensors in the attenuated
and unattenuated state by connecting the switch output to the unconnected socket
of the distribution unit and then to the buzzer socket. Make a note of the values in
the table.
Now connect the switching output of the capacitive sensor with the positive
operating voltage connection of the inductive sensor. To do this, plug the switching
output of the capacitive sensor into the unconnected socket of the distribution unit
and connect the positive connection of the inductive sensor to this. In this way, the
inductive sensor receives its supply voltage only when an object has been detected
by the capacitive sensor. The switching output of the inductive sensor is also
plugged into an unconnected socket in the distribution unit.
Measure the individual voltages listed below:
V
op
: Operating voltage
V
1
: Voltage on the switched through output of the capacitive sensor
(remaining operating voltage of the inductive sensor)
V
2
: Voltage on the switched through output of the inductive sensor
Enter the measured values in the table.
Note
Inductive and capacitive proximity sensors are referred to as attenuated proximity
sensors, when the proximity sensor detects an object.
Practical assembly
Exercise 18
Festo Didactic GmbH & Co. FP1110 A-169
Current consumption of a capacitive sensor
a) Switching output in unconnected socket
Switching status Current consumption [mA]
unattenuated
attenuated
b) Switching output in buzzer socket
Switching status Current consumption [mA]
unattenuated
attenuated
Current consumption of an inductive sensor
a) Switching output in unconnected socket
Switching status Current consumption [mA]
unattenuated
attenuated
b) Switching output in buzzer socket
Switching status Current consumption [mA]
unattenuated
attenuated
Voltage measurement with series connection
Voltage [V]
Operating voltage V
op
Voltage V
1
Voltage V
2
Evaluation
Exercise 18
A-170 Festo Didactic GmbH & Co. FP1110
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Conclusions
Festo Didactic GmbH & Co. FP1110 A-171
To be acquainted with the use of optical proximity sensors with fibre-optic cables for
the orientation of components.
Study the exercise. You will find hints and explanations in the textbook Proximity
Sensors.
Before the practical construction of the exercise, read through the data sheets of
the components required.
Assemble the components.
You can carry out the exercise in accordance with the description in paragraph
"Practical assembly".
Make a note of everything you consider of particular interest.
Warning
The electrical power supply must be switched on only after all connections have
been established and checked. After completion of the exercise, the voltage supply
must be switched off before the components are dismantled.
Exercise 19
Position detection with proximity sensors
Training aim
Exercise definition
Exercise 19
A-172 Festo Didactic GmbH & Co. FP1110
Valve housings are transported on a conveyor belt. The orientation of these
housings is to be monitored by sensors. The fixing holes in the housings provide
suitable distinguishing characteristics. Incorrectly orientated components are
passed to the turning station.
1
2
Valve housing (1), Fibre-optic cables (2)
Problem description
Positional sketch
Exercise 19
Festo Didactic GmbH & Co. FP1110 A-173
1
3
2
4
5
START STOP RESET
CLOCK
1000 100
Imp./s
Im p./s
Im p.
Im p./s
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 1 Counting unit, D:ER-ZE-FP1110-...
3 2 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
4 2 Fibre-optic cable unit SE, D:ER-SOEZ-LK-SE-...
5 1 Set of test objects, workpiece valve housing, part 35
1 Set of test objects, screw driver, part 36
Layout
Components list
Exercise 19
A-174 Festo Didactic GmbH & Co. FP1110
3
2 1
START STOP RESET
CLOCK
1000 100
Imp./s
I mp./s
I mp.
I mp./s
BN(1)
BK(4)
BU(3)
WH(2)
BN(1)
BK(4)
BU(3)
WH(2)
3
Item no. Qty. Designation
1 1 Distribution unit, D:ER-VERT-SENSOR-...
2 2 Optical sensor unit LL 1, D:ER-SEO-L-Q-...
3 1 Counting unit, D:ER-ZE-FP1110-...
+24 V DC
0 V
BN(1)
BU(3)
BN(1)
BU(3)
BN(1)
BU(3)
Electrical connections
Electrical circuit diagram
Exercise 19
Festo Didactic GmbH & Co. FP1110 A-175
Mount the distribution unit and the two optical sensor units LL 1 with the fibre-optic
cable units SE on the profile plate. Arrange a distance of 10 cm between the two
light barriers and a distance of 5 cm between optical emitter and receiver unit.
Connect the 24V electrical power supply and the two sensors to the distribution unit
(see fig. "Electrical connections"). Connect the normally closed output of the first
sensor unit to the RESET socket of the counting unit. The normally closed output of
the second sensor is connected to the CLOCK socket of the counting unit. The
indicating display mode switch is in position "Imp".
Move the valve housing, lying on its side, through the gap between the two light
barriers in such a way that the fixing holes are on the level of the optical axis. Make a
note of the result with both orientations.
Mounting the fibre-optic cables
Insert the fibre-optic cables into the plugs of the fibre-optic unit up to stop. Securely
tighten locking screw
Preparing the counting unit for measurement
Press the "Stop", "Reset" and "Start" buttons before the first measurement, in
order to prepare the counting unit for measurement.
Practical assembly
Exercise 19
A-176 Festo Didactic GmbH & Co. FP1110
Exercise 19
Festo Didactic GmbH & Co. FP1110 A-177
Orientiation Signals counted
1 upper hole
2 upper holes
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
Evaluation
Conclusions
Exercise 19
A-178 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 B-1
Part B Fundamentals
The theoretical fundamentals for the function package Proximity Sensors are
described in the textbook
Lerning system for Automation and Technology
Proximity Sensors
Part B
Part B
B-2 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-1
Part C Solutions
Magnetic proximity sensors
Solution 1
Switching characteristics of a contacting magnetic proximity sensor___________ C-3
Solution 2
Switching characteristics of a contactless magnetic proximity sensor __________ C-5
Inductive proximity sensors
Solution 3
Switching distance of an inductive proximity sensor ________________________ C-7
Solution 4
Sensing of different metals with inductive proximity sensors _________________ C-9
Solution 5
Influence of the object surface on the switching distance ___________________ C-11
Optical proximity sensors
Solution 6
Response characteristics of a through-beam sensor _______________________ C-13
Solution 7
Response characteristics of a retro-reflective sensor _______________________ C-15
Solution 8
Sensing range of a diffuse optical sensor ________________________________ C-17
Solution 9
Sensing range of a diffuse optical sensor with fibre-optic cable ______________ C-21
Capacitive proximity sensors
Solution 10
Switching distance of a capacitive sensor ________________________________ C-23
Solution 11
Influence of material thickness
on the switching distance of a capacitive sensor __________________________ C-25
Ultrasonic proximity sensors
Solution 12
Sound wave form and reflection characteristics of an ultrasonic sensor _______ C-27
Part C
Part C
C-2 Festo Didactic GmbH & Co. FP1110
Applications
Solution 13
Speed measurement _________________________________________________ C-29
Solution 14
Determining rotational speeds _________________________________________ C-31
Solution 15
Sensing the correct assembly of workpieces______________________________ C-33
Solution 16
Liquid level measurement _____________________________________________ C-35
Solution 17
Checking of threads __________________________________________________ C-37
Solution 18
Logic combinations of proximity sensor signals ___________________________ C-39
Solution 19
Position detection with proximity sensors________________________________ C-41
Festo Didactic GmbH & Co. FP1110 C-3
Magnet 2
Magnet 1
Switching characteristics for magnetic sensor unit 1 (D.ER-SMEO-..) with varying orientations of the axis of the
magnetic poles
As can be seen from the figure above, two or even three switching areas may be
observed, depending on the orientation of the axis of the magnetic poles. This
ambiguity of the output signals can be prevented by attaching the magnet with the
correct orientation of the axis and, given a specific field strength, at the correct
distance.
In the case of sensor-magnet combinations which are obtained separately, it is
important to check which switching characteristic is achieved. Only in this way can
the effective application of the sensor be guaranteed.
You will find further information and explanations in the textbook Proximity
Sensors.
Solution 1
Switching characteristics of a contacting magnetic proximity sensor
Evaluation
Conclusions
Solution
C-4 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-5
Magnet 2
Magnet 1
Switching characteristics for magnetic sensor unit 2 (D.ER-SMTO-..) with varying orientations of the axis of the
magnetic poles
As can be seen from the figure above, two switching areas may be observed,
depending on the orientation of the axis of the magnetic poles. This ambiguity of the
output signals can be prevented by attaching the magnet with the correct
orientation of the axis and, given a specific field strength, at the correct distance.
In the case of sensor-magnet combinations which are obtained separately, it is
important to check which switching characteristic is achieved. Only in this way can
the effective application of the sensor be guaranteed.
With correctly orientated contactless magnetic sensors, a bounce-free output
switching signal is obtained.
You will find further information and explanations in the textbook Proximity
Sensors.
Solution 2
Switching characteristics of a contactless magnetic proximity sensor
Evaluation
Conclusions
Solution
C-6 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-7
Inductive sensor unit 1 (D:ER-SIEH-M18B-...)
Switch-on point: 5.3 mm
Switch-off point: 5.6 mm
Hysteresis: 0.3 mm
Inductive sensor unit 2 (D:ER-SIEH-M12B-...)
Switch-on point: 3.5 mm
Switch-off point: 3.7 mm
Hysteresis: 0.2 mm
With inductive sensors, the attainable switching distance is dependent on the
diameter of the resonant circuit coil and therefore on the size of the cylindrical
sensor. The larger the diameter, the larger the switching distance.
The difference between the switch-on point and the switch-off point is known as
hysteresis. This is essential to guarantee reliable switching of the sensor. Should the
switch-on point and switch-off point coincide, this would result in fluttering of the
output signal.
The measured switching distances give an indication as to the required adjustment
of inductive sensors.
Further information and explanations can be found in the textbook Proximity
Sensors.
Solution 3
Switching distance of an inductive proximity sensor
Evaluation
Conclusions
Solution
C-8 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-9
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Reduction factor
Mild steel
S 235 JR,
part 3
5.9 6.2 0.3 1
Stainless steel,
part 4
5.4 5.7 0.3 0.91
Aluminium,
part 5
3.2 3.4 0.2 0.54
Brass,
part 6
3.2 3.4 0.2 0.54
Copper,
part 7
2.5 2.8 0.3 0.42
This exercise demonstrates that different metals result in different switching
distances. With reduced switching distances the tolerances for the distances
between containers are smaller, and the need for adjustment increases.
This effect depends on the difference in electric conductivity of the materials used.
Further information and explanations can be found in the textbook Proximity
Sensors.
Solution 4
Sensing of different metals with inductive proximity sensors
Evaluation
Conclusions
Solution
C-10 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-11
Length of sides [mm] Switching gap [mm]
Mild steel S 235 JR, part 11: 30 6.2
Mild steel S 235 JR, part 12: 25 6.1
Mild steel S 235 JR, part 13: 20 6.0
Mild steel S 235 JR, part 14: 15 5.8
Mild steel S 235 JR, part 15: 10 5.1
Mild steel S 235 JR, part 16: 5 3.1
The switching distance of an inductive sensor depends not only on the type of
material (see exercise 4), but also on the size of the object to be detected.
In general, the switching distance of inductive sensors for objects which are smaller
than the standard calibrating plate depends on the area of the object detected, i.e.,
for objects which are smaller than the standard calibrating plate, the achievable
switching distance is smaller than the nominal switching distance.
Solution 5
Influence of the object surface on the switching distance
Evaluation
Conclusions
Solution
C-12 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-13
Material Detection yes/no
Mild steel S 235 JR, part 3 yes
Stainless steel, part 4 yes
Aluminium, part 5 yes
Cardboard, part 8 yes
Rubber, part 9 yes
Plastic, transparent, part 10 no
With a through-beam sensor, objects made of reflective materials can also be
reliably detected. Transparent materials, however, present a problem.
If required, transparent materials can also be detected. Sensitivity must be reduced
at the light barrier receiver with the potentiometer to this end. By further reducing
the beam through the material, detection is possible. This, however, leads to a
reduction in the switching distance. The transparent plastic object provided in the
function package will not be detected, if it is clean and unscratched.
When guiding the objects into the light beam from the side, their position can be
precisely detected.
Solution 6
Response characteristics of a through-beam sensor
Evaluation
Conclusions
Solution
C-14 Festo Didactic GmbH & Co. FP1110
In the illustration below, the switch-on points of the response curve of the through-
beam sensor are shown. You will see, that the emitter emits light only through one
lens, whereas the receiver receives light through both lenses.
Response curve of the through-beam sensor
Note
If the sensor emitter and sensor receiver are installed vertically to the profile plate,
you obtain a response curve symmetrical in relation to the optical axis.
Festo Didactic GmbH & Co. FP1110 C-15
Material Detection yes/no
Mild steel S 235 JR, part 3 yes*
(no, if reflective and perpendicular
to optical axis)
Stainless steel, part 4 no*
(yes, if angle other than 90)
Aluminium, part 5 no*
(yes, if angle other than 90)
Brass, part 6 no*
(yes, if angle other than 90)
Copper, part 7 yes*
(no, if reflective and perpendicular
to optical axis)
Cardboard, part 8 yes*
Rubber, part 9 yes
Plastic, transparent, part 10 yes *
* With these objects detection depends on the surface characteristics of the object,
the angle and the distance between sensor and object.
Retro-reflective sensors function reliably if the light path is interrupted by opaque
objects.
Yet, if an object with a reflecting surface enters the beam of emitted light at a
90 angle to the optical axis, there is no certainty that it will be detected by the retro-
reflective sensor. This phenomenon may be avoided if the object is placed at an
oblique angle to the optical axis.
Note
The use of retro-reflective sensors employing polarised light offers another
possibility. These, too, provide reliable detection of reflecting objects. You will find
further relevant explanations in the textbook Proximity Sensors.
Solution 7
Response characteristics of a retro-reflective sensor
Evaluation
Conclusions
Solution
C-16 Festo Didactic GmbH & Co. FP1110
The detection of transparent objects may sometimes be possible, if the sensitivity is
reduced to such an extent that the attenuation through the twofold passage of the
light beam through the object suffices.
In the following illustration, the switch-on points are shown as the response curve of
the optical retro-reflective sensor.
Response curve of the retro-reflective sensor
Note
There can be deviations from the shape of the response curves. Non-uniformity of
the equipment parameters may be among the reasons. Slight dirt contamination
may affect the shape of the curves. If the retro-reflective sensor is mounted vertically
to the profil plate, it results in a response curve lying symmetrically to the optical
axis.
Triple reflectors have the special characteristic of reflecting the light beam back to
the emitter, even if their surface is not exactly normal to the light beam impinging on
it. This simplifies the adjustment of the reflector. In accordance with the laws of
optics, flat mirrors reflect the light beam away from the optical axis.
Reflection of a light beam from a triple reflector and a flat mirror
Festo Didactic GmbH & Co. FP1110 C-17
Note
Your measured values may deviate from those given in the tables, because these
values very much depend on the potentiometer setting and the nature of the surface
of the objects selected from the set of test objects.
Experiment 1
Optical sensor unit RT 1 (D:ER-SOE-RT-Q-..)
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side, part 17 300 340 40
Kodak grey card, grey side, part 17 175 210 35
Plastic, transparent, part 18 430 450 20
Plastic, red, matted side, part 19 220 250 30
Plastic, blue, matted side, part 20 190 230 30
Plastic, black, matted side, part 21 75 100 25
Cardboard, white, part 22 275 290 15
Mild steel S 235 JR, part 3 540 630 90
Stainless steel, part 4 520 610 90
Aluminium, part 5 550 570 20
Brass, part 6 660 690 30
Copper, part 7 370 430 60
Rubber, part 9
Solution 8
Sensing range of a diffuse optical sensor
Evaluation
Solution
C-18 Festo Didactic GmbH & Co. FP1110
Experiment 2
Optical sensor unit RT 2 (D:ER-SOE-RT-M18-..)
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side, part 17 150 185 35
Kodak grey card, grey side, part 17 90 120 30
Plastic, transparent, part 18 100 130 30
Plastic, red, matted side, part 19 110 140 30
Plastic, blue, matted side, part 20 105 130 25
Plastic, black, matted side, part 21 40 60 20
Cardboard, white, part 22 150 180 30
Mild steel S 235 JR, part 3 160 190 30
Stainless steel, part 4 170 200 30
Aluminium, part 5 200 240 40
Brass, part 6 280 300 20
Copper, part 7 180 200 20
Rubber, part 9
Solution
Festo Didactic GmbH & Co. FP1110 C-19
It becomes apparent that the range of the sensor varies according to the
reflectiveness of the material.
With the optical sensor unit RT 1 (diffuse sensor, D.ER-SOE-RT-Q-..) sensing ranges
of up to approximately 800 mm (for reflecting surfaces) are achieved. As this sensor
operates with infra-red light, the lightbeam is not visible. This can lead to difficulty
with adjustments. The shape of the response curve is dependent on the
potentiometer setting. The asymmetry is a result of the horizontal arrangement of
the components (the emitter being adjacent to the receiver and the object
approaching from the side).
Response curve of the diffuse sensor D:ER-SOE-RT-Q-...
Conclusions
Solution
C-20 Festo Didactic GmbH & Co. FP1110
With the sensor unit RT 2 (diffuse sensor, D.ER-SOE-M18-..) sensing ranges of
approximately 500 mm (for reflecting surfaces) can be achieved. The asymmetry
which is visible in the response curve is because the vertical alignment of the emitter
and the receiver is not accurate.
Response curve of the diffuse sensor D:ER-SOE-RT-M18-...
Note
When detecting objects other than the Kodak grey card, which is 100 x 100 mm, this
may create different response curves for the two diffuse sensors.
Festo Didactic GmbH & Co. FP1110 C-21
Note
Depending on the surface characteristics of the materials investigated, your
measurements may reveal differences in sensing ranges. The cut edge of the fibre-
optic cable and the optical transition from transmitter and receiver optics to the
fibre-optic cable also influence measurement results.
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Kodak grey card, white side, part 17 8.3 10.5 2.2
Kodak grey card, grey side, part 17 4.1 5.5 1.4
Plastic, transparent, part 18 4.1 4.9 0.8
Plastic, red, matted side, part 19 6.2 8.0 1.8
Plastic, blue, matted side, part 20
Plastic, black, matted side, part 21
Cardboard, white, part 22 8.9 10 1.1
Mild steel S 235 JR, part 3 12.9 14.8 1.9
Stainless steel, part 4 10.4 12.2 1.8
Aluminium, part 5 13.0 15.0 2.0
Brass, part 6 14.2 16.6 2.4
Copper, part 7 13.1 14.6 1.5
Rubber, part 9
Solution 9
Sensing range of a diffuse optical sensor with fibre-optic cable
Evaluation
Solution
C-22 Festo Didactic GmbH & Co. FP1110
Using fibre-optic cables, only small sensing ranges can be achieved. It is, therefore,
necessary to approach the objects closely.
Their small overall size permits use in space saving applications. Application in
inaccessible places is possible through the high flexibility of the fibre optics. They
are capable of detecting the smallest objects and a high degree of sensing accuracy
can be achieved. They can be used in surroundings subject to explosion risk,
whereby the electrical components of the proximity sensor have to be hermetically
separated.
Note
In locations with high temperature (e.g. 200 C) glass fibre optic cables are
preferable (see textbook Proximity Sensors).
Conclusions
Festo Didactic GmbH & Co. FP1110 C-23
Material Switch-on point
[mm]
Switch-off point
[mm]
Hysteresis
[mm]
Mild steel S 235 JR, part 3 8.0 9.0 1.0
Stainless steel, part 4 8.1 9.1 1.0
Aluminium, part 5 7.8 8.5 0.7
Brass, part 6 7.9 8.6 0.7
Copper, part 7 8.1 8.9 0.8
Cardboard, part 8 4.2 5.0 0.8
Rubber, part 9 6.5 7.4 0.9
Plastic, transparent, part 10 2.2 2.7 0.5
As the values given in the table are dependent on the potentiometer setting, your
measurements may produce different figures, if the value achieved by the initial
adjustment for the steel plate already deviates from the one in the table.
Metallic and non-metallic objects can be detected with capacitive proximity sensors.
Compared, e.g. to optical diffuse sensors, they offer the advantage of being able to
detect also materials with very low reflectivity (very dark surfaces). With materials of
very low dielectric constants (e.g. many plastics), detection takes place only from a
certain thickness and above (see exercise 11).
Note
The capacitive proximity sensor responds also to many liquids. It has, however, to
be observed that an unintended wetting of the active surface of the proximity
sensor, e.g. through water condensate, may lead to an output signal.
Solution 10
Switching distance of a capacitive sensor
Evaluation
Conclusions
Solution
C-24 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-25
Material thickness [mm] Switching distance [mm]
Plastic, part 23, 2,0 1.9
Plastic, part 24, 3,0 2.6
Plastic, part 25, 5,0 2.8
Plastic, part 26, 8,0 3.0
Plastic, part 27, 11,0 3.3
Plastic, part 28, 14,0 3.6
Plastic, part 29, 17,0 3.7
As the results depend on the potentiometer setting, the values of your
measurements may deviate, if the initial adjustment for the steel plate does not
result in a switching distance of precisely 8 mm.
As can be seen from the graph, in the case of plastic, the switching distance of a
capacitive sensor is dependent on the material thickness.
With a capacitive sensor, the capacitive change which results from the proximity of
the object is measured. Therefore, a sufficiently large amount of the material has to
be put before the sensor in order for it to react. The smaller the dielectric constant of
the material, the more material needs to be brought into the active zone of the
sensor in order for it to be detected (for numerical values of the dielectric constants
for different materials see textbook Proximity Sensors, for example).
The values for the reduction factor of the switching distance are indicated for those
material thicknesses, for which the maximum possible switching distance for that
material has been achieved.
Solution 11
Influence of material thickness on the switching distance of a capacitive sensor
Evaluation
Conclusions
Solution
C-26 Festo Didactic GmbH & Co. FP1110
0
1
2
3
5
4
mm
0 mm 14 12 10 8 6 4 2 1 3 5 7 9 11 13 15 17
S
w
i
t
c
h
i
n
g
d
i
s
t
a
n
c
e
Material thickness
Switching distance of a capacitive sensor as a function of material thickness of plastic
Festo Didactic GmbH & Co. FP1110 C-27
Material Detection yes/no
Mild steel S 235 JR, part 3 yes, 7
Stainless steel, part 4 yes, 8
Aluminium, part 5 yes, 5
Brass, part 6 yes, 5
Copper, part 7 yes, 4
Cardboard, part 8 yes, 4
Rubber, part 9 yes, 5
Plastic, transparent, part 10 yes, 3
Response curve of an ultrasonic sensor
The direction from which the object approaches the beam emitted by the sensor is
marked by arrows in the illustration.
Solution 12
Sound wave form and reflection characteristics of an ultrasonic sensor
Evaluation
Solution
C-28 Festo Didactic GmbH & Co. FP1110
Ultrasonic sensors are capable of detecting all materials contained in the set of test
objects within a specific range of angles. Even thin, transparent plastic film is
reliably detected. Particularly with materials of smooth surface, one should note
how the reflected beam is sensitive to angle. With coarse grained bulk materials, or
when detecting textiles, this effect is not so pronounced.
Also after a double deflection of the beam by 90, detection of a flat surface by an
ultrasonic sensor is possible.
Note
In locations where intense external noise permeates the ultrasonic range, ultrasonic
sensors can be used with reservations only. The external noise may be detected,
resulting in faulty signals. Sources of such external noise can be e.g. metal saws,
compressed air guns and similar appliances.
Conclusions
Festo Didactic GmbH & Co. FP1110 C-29
Switching distance
Potentiometer at maximum setting
Switch-on distance 202 mm
Switch-off distance 215 mm
Hysteresis 13 mm
Speed measurement
Indicated value 150
Corresponding time 0.150 s
Path 0.10 m
Speed 0.667 m/s (approx. 2.4 km/h)
With an optical sensor unit LL 1 it is possible to determine the handling speed of
components on a conveyor even if the mounting area is restricted. Due to the
optimum range of the through-beam sensor, a distance of approximately 100 mm
can be reliably monitored.
Note
Due to light output reserves of the optical sensor unit, the actual range can be in
excess of 200 mm.
Solution 13
Speed measurement
Evaluation
Conclusions
Solution
C-30 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-31
Motor voltage [V] Output-pulse
frequency
SOE-L-Q-
[Imp./s]
Output-pulse
frequency
SIEH-M12B-
[Imp./s]
Speed RS [r.p.m.]
4,0 84 84 630
4,5 95 95 712
5,0 107 108 802
5,5 119 119 892
6,0 131 131 982
6,5 144 144 1080
7,0 156 156 1170
7,5 168 168 1260
8,0 180 180 1350
8,5 193 192 1447
9,0 205 205 1537
9,5 216 216 1620
10,0 228 228 1710
10,5 241 240 1807
11,0 253 253 1897
11,5 265 265 1987
12,0 278 277 2085
12,5 289 254 2167
13,0 303 116 2272
13,5 315 49 2362
14,0 327 5 2452
15,0 352 2640
16,0 376 2820
17,0 401 3007
18,0 423 3172
19,0 448 3360
20,0 473 3547
Solution 14
Determining rotational speeds
Evaluation
Solution
C-32 Festo Didactic GmbH & Co. FP1110
The values given in this table are the results of a test measurement. The results of
your measurements may deviate from this data. For the calculation of speed, the
value of the optical sensor was used.
1. With the rotary unit, the limiting frequency of the inductive sensor is achieved.
The interval times between the pulses become so short that the output signal
cannot drop down to 0 V. This is why the counting unit shows less pulses per
second beyond the limiting frequency.
2. With the rotary unit, the limiting frequency of the optical sensor is not achieved
which is why the speed display accelerates steadily in this case.
When determining speed, ensure that the maximum switching frequency of the
sensor used is higher than the expected maximum speed.
From the component data sheets of the sensor used, it can be seen that the
maximum switching frequency for the inductive sensor (D:ER-SIEH-M12B-..) is
approximately 400 Hz, and the maximum switching frequency for the optical sensor
(D:ER-SOE-L-Q-..) approximately 1000 Hz. These values are confirmed by the
measurements.
If inductive sensors are used, the speed of metallic perforated disks or gears can be
determined. Due to the high switching frequencies, it is also possible to reliably
determine fast rotations. Due to the small switching gap of the sensor, adjustment
is, however, difficult.
With optical sensors, it is also possible to determine speed over larger distances.
However, they often have a reduced switching frequency and the optical
components can easily become contaminated.
Conclusions
Festo Didactic GmbH & Co. FP1110 C-33
Object Switching distance [mm]
Base plate
Gear wheel 8.0
If a distance of 15 mm is selected between the fibre-optic cable unit and the base
plate, detection of the empty base plate is not possible if the potentiometer of the
sensor has been preset. If the gear wheel is mounted correctly, this will result in
reliable detection, i.e. the sensor will respond. Care is to be taken that the central
hole of the gear wheel does not lead to faulty indication.
Using a diffuse sensor with fibre-optic cable it is possible to detect on a unit whether
a component (in this case the gear wheel) has been mounted correctly. Background
fade-out (the empty base plate not being recognised) is possible, if the
potentiometer is set accordingly.
If the objects are brought too close towards the fibre-optic cable unit, then they are
not detected because insufficient light is reflected into the receiver.
Solution 15
Sensing the correct assembly of workpieces
Evaluation
Conclusions
Solution
C-34 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-35
Capacitive sensor unit
Beaker directly at PS
*)
water level
42 mm, PS switches on
Beaker 3 mm from PS
*)
On emptying the beaker
water level
58 mm, PS switches on
the PS remains switched on upon further filling
54 mm, PS switches off
Through-beam sensor
Beaker placed between emitter and receiver
Water level 40 mm on
Upon further filling 58 mm off
Diffuse sensor with fibre-optic cable
Distance PS
*)
water level 11 mm on
Distance PS
*)
water level 15 mm off
*) PS = Proximity sensor
The values in the table are the results of exemplary measurements.
Solution 16
Liquid level measurement
Evaluation
Solution
C-36 Festo Didactic GmbH & Co. FP1110
Capacitive sensors
With a capacitive sensor, it is possible to detect a liquid level right through the walls
of certain containers.
For this, the material of the container wall must be of a type undetectable by the
proximity sensor, e.g. plastic. The thickness should not be more than 2 4 mm.
Hence the first step is to adjust the sensitivity so that the sensor does not react to
the container wall. This is possible only if it is made from a material with a low
dielectric constant.
If liquid is then introduced, the level can be detected by the sensor.
With capacitive sensors, there is no need for contact between sensor and the filling
material to be detected, but one is usually limited to plastics as far as the container
walls are concerned. If the proximity sensor is fitted inside the container, one has to
select sensor designs not sensitive to corrosion or other attack by the substance
used.
Optical sensors
With the optical methods, the liquid level must be directly visible. Depending on
container material, one thus has to fit flanged transparent standpipes at suitable
places on the container.
When sensing with a through-beam sensor fitted at an angle, one has to bear in
mind that surface disturbances may lead to faulty detection.
With the diffuse sensor, wetting of the sensing head may lead to a false signal. If a
liquid droplet remains suspended from the sensing head, light is reflected from
emitter to receiver, even after the liquid level has fallen.
ert.
Note
When sensing filling levels, one is not limited to the application of detecting liquids.
Other bulk materials, too, which are kept in a storage container, can be detected.
Conclusions
Festo Didactic GmbH & Co. FP1110 C-37
Mark the correct response
a) Threaded screw recognised / not recognised
b) Plain screw recognised / not recognised
The threaded screw is reliably recognised whereas the plain screw is not detected.
Therefore, the checking for threads can easily be carried out.
However, faults in the thread itself cannot be detected by this method.
Solution 17
Checking of threads
Evaluation
Conclusions
Solution
C-38 Festo Didactic GmbH & Co. FP1110
Festo Didactic GmbH & Co. FP1110 C-39
Current consumption of a capacitive sensor
a) Switching output in unconnected socket
Switching status Current consumption [mA]
unattenuated 2.4
attenuated 7.2
b) Switching output in buzzer socket
Switching status Current consumption [mA]
unattenuated 2.4
attenuated 40 bis 55*
Current consumption of an inductive sensor
a) Switching output in unconnected socket
Switching status Current consumption [mA]
unattenuated 15.8
attenuated 15.8
b) Switching output in buzzer socket
Switching status Current consumption [mA]
unattenuated 15.8
attenuated 40 bis 55*
* depending upon buzzer potentiometer setting
Voltage measurement with series connection
Voltage [V]
Operating voltage V
op
24.4
Voltage V
1
23.5
Voltage V
2
22.2
Solution 18
Logic combinations of proximity sensor signals
Evaluation
Solution
C-40 Festo Didactic GmbH & Co. FP1110
A simple logic connection of the output signals of sensors is possible without the
use of programmable logic controls. With the series connection of sensors realised
in this exercise, an AND connection has been achieved, i.e. the output signal is
obtained only if all the series connected sensors switch through.
Note
Series connection of sensors is to be used only, if there are insufficient inputs for a
programmable logic control (PLC), or a PLC is not used.
Please note the following with regard to this circuit type:
The current consumption due to the load and the current consumption of the
sensors connected in series is accumulative, i.e. the maximum current on contact
of the first sensor has to be sufficient for current supply to all subsequent
sensors and the load.
In the switched through status each sensor has a voltage drop (in this instance
approx. 1.3 V). The voltage available for the load reduces by the sum of the
voltage drops.
Because the subsequently switching sensors receive their operating voltage only
when the previous sensor has switched through, the activating time delay has to
be taken into account, i.e. the time which the sensor needs after actuation to be
able to react to the objects.
Conclusions
Festo Didactic GmbH & Co. FP1110 C-41
Orientation Signals counted
1 upper hole 2
2 upper holes 3
Using optical proximity sensors with fibre-optic cables, it is possible to check the
orientation of components. In particular, the use of fibre-optic cables makes it
possible to detect small structural features reliably.
In this exercise the counting unit is a substitute of a programmable logic controller
(PLC).
Note
It is easy to set up an automated process sequence based on the evaluation of
sensor output signals by a programmable logic controller. For this, the switching
outputs of the sensors must be connected to the appropriate inputs of the
controller. Suitable programming can bring about detection of orientation and an
appropriate reaction to this.
Solution 19
Position detection with proximity sensors
Evaluation
Conclusions
Solution
C-42 Festo Didactic GmbH & Co. FP1110