Technical Information: Product Finder Home Page
Technical Information: Product Finder Home Page
Technical Information: Product Finder Home Page
Technical Information
1
T
E
C
H
N
I
C
A
L
I
N
F
O
R
M
A
T
I
O
N
5) Load Bearing Mechanisms
Load bearing mechanisms are the structural backbone of any linear/rotary motion system, and are a critical
consideration. This section will introduce most of the more common types of load bearing mechanisms
found in linear motion machinery. In general, bearings allow smooth, low friction motion between two
surfaces loaded against each other. The motion can be either rotary (such as in a turning shaft) or linear
(such as a machine part moving back and forth). Some applications require that a bearing accommodate
both types of motion simultaneously, which is referred to as a combination bearing. In both cases there
should be a strong attempt to provide enough lubrication to keep the bearing surfaces separated by a film
of oil. The absence of physical contact provides most bearings with long service lives.
Bearings are evaluated on the basis of how much load they carry, at what speeds they can carry the load,
and how long they will serve under those conditions. Friction, start-up torque, shock- and impact-resistance,
operating environment, rigidity, size, cost, complexity, and lubricating procedures are also important design
considerations.
The following diagram reveals the basic bearing families more widely found in linear motion systems. The
distinction between families is made by the type of motion and type of loading being considered. Bearings
accommodate rotational and/or translational motion. Translational bearings, or linear bearings, are loaded
perpendicular (radial) to the direction of motion. Rotational bearings can be loaded either perpendicular to
the axis of rotation (radial) or parallel to the axis of rotation (thrust).
Most bearings can be classified into one of two general types. The distinction between bearing types is
made by the nature of the bearing mechanism. The two types each have a number of different possible
configurations, and some of the more common configurations will now be discussed. Since many bearings
are either specialized or of proprietary design, this discussion is by no means intended to be all exhaustive,
but rather to serve as an introduction.
Plain Bearings, or Journal Bearings, are the most basic type of
bearing. They have no moving parts, they support loads through sliding
contact, and are usually the least costly to install. Some plain bearings
are self-lubricating and maintenance-free while others are not. In fact,
some plain bearings are classified as to the lubricating method required.
Typically, plain bearings will operate right up to the point of failure with
little or no warning signs. Since the motion involved is usually low level,
the results of failure are typically noncatastrophic, and replacement or
repair is fairly simple. There are several ways to size plain bearings for
an application, as outlined at the end of this section.
Thrust
TRANSLATION
(OR LINEAR)
JOURNAL
OR RADIAL
BEARING
Bearing
surface
THRUST
BEARING
Radial
Load
ROTATION
Motion
Motion
Load
Load
PLAIN BEARING
Bearing
Journal
Product Finder Home Page
Techno Linear Motion Catalog 20
Technical Information
1
T
E
C
H
N
I
C
A
L
I
N
F
O
R
M
A
T
I
O
N
Raceways Filling slots
Rolling Element Bearings, or roller bearings, make up the bulk of
commercially available and applied bearings. These types of bearings
rely on either balls or rollers to carry the load. The rolling motion
produces less friction than found in plain bearings. For this reason,
roller bearings are also referred to as antifriction bearings. Both radial
loads and thrust loads can be supported by this type of bearing.
Lubrication is either permanently sealed in the bearing or is required
during operation. The largest causes of failure are either exceeding
temperature, load and speed limits, or providing insufficient lubrication
during operation. Since roller bearing applications often involve heavy
loads and high speeds, failure can be catastrophic, extremely costly
and time consuming to repair. Usually there will be an increase in the
sound of the balls or rollers in the raceways when approaching failure.
There are many different configurations of roller element bearings, and
some are discussed in the following section.
Radial Ball Bearings come in two basic variations which
are called the Conrad type, or nonfilling slot, and the
maximum capacity type, or filling slot. The Conrad type has
a deep, uninterrupted raceway in inner and outer rings. This
design is capable of carrying heavy radial and moderate bi-
directional thrust loads. The maximum capacity bearing has
more balls than an equivalent sized Conrad type, therefore
carries a higher radial load. However, the filling slots require
that the thrust loads be light and applied only in combination
with a heavier radial load. If moderate thrust loads are
present, the maximum type can be replaced by a double
row Conrad type bearing. Selection of this type bearing is
outlined in the following section.
Thrust Ball Bearings are designed to
provide axial shaft location and support
thrust l oads. Angul ar contact bal l
bearings support radial as well as thrust
loads, and the ratio of permissible radial
to thrust loads depends upon the angle
of contact between the races and the
bearing axis. Thrust ball bearings are
commonl y used i n l i near mot i on
systems to support the drive screw.
Conrad-type ball bearing, left, and
maximum-capacity (filling slot) type, right
Flat-race, flat-seat thrust ball bearing, A, and
grooved-race, flat-seat thrust ball bearing, B
Aligning, double-acting, grooved-race
thrust ball bearing
A
B
Banded thrust ball bearing, A, and
aligning, single-acting, grooved-race
thrust ball bearing, B
B
A
Outer race
Rolling element
Inner
Race
ROLLING ELEMENT
Product Finder Home Page
Techno Linear Motion Catalog 21
Technical Information
1
T
E
C
H
N
I
C
A
L
I
N
F
O
R
M
A
T
I
O
N
Flat race, flat seat bearings consist of two flat washers and a ball retaining assembly. They are used
when the ball retainer assembly must carry thrust loads without restraining shaft oscillations or flexures.
They work well with light loads and are very economical.
Grooved race, flat seat bearings are the most common type of thrust ball bearing. They consist of a shaft
mounted small bore washer, a large housing mounted bore washer, and a ball retaining assembly. Grooved
race bearings have a load bearing capacity approximately 4 times greater than flat race bearings.
Banded thrust ball bearings are self-contained, have grooved races, have a stationary and rotating face
with full ball complement, and are encased in a containing band. These bearings are most commonly used
where the bearing's outer circumference must be protected from contamination, for blind installation, or
where separating forces cause substantial axial motion of bearing components.
Aligning grooved race bearings are a variation of grooved race bearings, and are available in single and
double acting types. Aligning members compensate for initial misalignment due to shaft deflection or
mismatch, while allowing uniform distribution of the load through the bearing. The double-acting type carries
thrust in both directions.
Linear Bearings are most commonly used in linear motion applications. This type of bearing is used when
loads are to be supported as the bearing rides back and forth along a shaft. Each raceway holds balls in
rolling contact between the shaft and inner bearing race of the bushing. The remaining balls recirculate
freely in the back side of the clearance in the ball train sleeve. A retainer is usually provided so that when
the bearing is removed from the shaft the balls stay in place. Linear bearings are as easy to install as a
plain bearing, while utilizing the advantages of rolling contact. Among the important factors when considering
load capacity of a linear bearing system are life expectancy, shaft hardness, and load orientation with
respect to the ball trains. Typically, if a lifetime of more than 2,000,000 inches is required, or if a shaft
hardness of less than Rc 60 is specified, then the load-carrying capacity of the bearing system will be
reduced.
Linear Bearings are the most commonly applied bearing type in linear motion systems. Clearly, many
applications involve using two sets of double linear rails, with two bearing blocks on each rail. In this case,
the load found on each bearing block is of interest when selecting the bearing components. There are three
basic orientations for the bearing system and loads, and each case is represented as follows.
Horizontal Translation with Normal Load: when a normal load is applied to a horizontal bearing system,
the loads on each bearing are found by using the following equations. The equations still apply if the load
is acting inside of the carriage mounting surface area. The orientation of the applied load with respect to
the bearing system is the important feature to consider. This means that these equations can still be used
even if the orientation of the translation is not horizontal, as long as the load to bearing relationship is
preserved.
Load-carrying balls
Recirculating balls
in clearance
Product Finder Home Page
Techno Linear Motion Catalog 22
Technical Information
1
T
E
C
H
N
I
C
A
L
I
N
F
O
R
M
A
T
I
O
N
L
2
L
4
L
2
L
4
d
3
d
1
( )
d
3
d
1
( )
L
4
L
2
d
4
d
2
d
3
d
4
F
1
F
3
F
2
F
4
L
F
1S
F
2S
F
2
F
1
F
3
d
1
TO CENTER
OF SCREW
FROM CENTER
OF TABLE
d
2
F
4S
F
2
F
2S
F
1S
L
F
1
F
3
F
4
L
d
1
d
3
d
1
d
3
d
4
d
2
F
3S
F
4
Horizontal Translation with Side Load: when a side
load is applied to the bearing system, the loads on the
individual bearings change, and new equations are
required. Each bearing will have a resultant normal load
as well as a side load. The orientation of the applied
load with respect to the bearing system is the important
feature to consider. This means that these equations
can still be used even if the orientation of the translation
i s not hori zontal , as l ong as the l oad to beari ng
relationship is preserved.
Vertical Translation with Vertical Load: when the load
is applied in the direction of travel (thrust), then the
following equations should be used to calculate the
loads on each bearing block. This type of configuration
i s general l y found i n verti cal appl i cati ons. The
orientation of the applied load with respect to the bearing
system is the important feature to consider. This means
that these equations can still be used even if the
orientation of the translation is not vertical, as long as
the load to bearing relationship is preserved.
F
2
= +
L
4
L
2
d
4
d
2
F
1
= +
d
3
d
1
( )
d
4
d
2
F
3
=
d
4
d
2
L
4
L
2
d
3
d
1
d
4
d
2
F
4
= + + ( )
F
2S
= F
4S
=
d
3
d
1
( )
F
1S
= F
3S
= +
L
4
d
3
d
1
( )
L
2
F
3
= F
4
=
L
2
d
4
d
2
( )
F
1
= F
2
=
L
2
d
4
d
2
( )
F
1
= F
3
=
L
2
d
3
d
1
( )
F
2
= F
4
=
L
2
d
3
d
1
( )
F
1S
= F
3S
=
L
2
d
4
d
2
( )
F
2S
= F
4S
=
L
2
d
4
d
2
( )
(7)
(8)
(9)
D
e
r
a
t
i
n
g
F
a
c
t
o
r
(
D
)
80
60
40
20
0
20
40
60
80
A
n
g
l
e
o
f
A
p
p
l
i
e
d
L
o
a
d
(
A
)
Force on Single Bearing Force on Double Bearing
Product Finder Home Page