Professional Documents
Culture Documents
HCS301
HCS301
Preliminary
DS21143A-page 1
FEATURES
Security
Programmable 28-bit serial number
Programmable 64-bit encryption key
Each transmission is unique
66-bit transmission code length
32-bit hopping code
34-bit xed code (28-bit serial number,
4-bit button code, 2-bit status)
Encryption keys are read protected
Operating
3.5V - 13.0V operation
Four button inputs
- 15 functions available
Selectable baud rate
Automatic code word completion
Battery low signal transmitted to receiver
Battery low indication on LED
Non-volatile synchronization data
Other
Functionally identical to HCS300
Easy to use programming interface
On-chip EEPROM
On-chip oscillator and timing components
Button inputs have internal pulldown resistors
Current limiting on LED output
Low external component cost
Typical Applications
The HCS301 is ideal for Remote Keyless Entry (RKE)
applications. These applications include:
Automotive RKE systems
Automotive alarm systems
Automotive immobilizers
Gate and garage door openers
Identity tokens
Burglar alarm systems
DESCRIPTION
The HCS301, from Microchip Technology Inc., is a code
hopping encoder designed for secure Remote Keyless
Entry (RKE) systems. The HCS301 utilizes the K
EE
L
OQ
code hopping technology, which incorporates high secu-
rity, a small package outline, and low cost, to make this
device a perfect solution for unidirectional remote key-
less entry systems and access control systems.
PACKAGE TYPES
HCS301 BLOCK DIAGRAM
The HCS301 combines a 32-bit hopping code
generated by a non-linear encryption algorithm, with a
28-bit serial number and six status bits to create a
66-bit transmission stream. The length of the
transmission eliminates the threat of code scanning
and the code hopping mechanism makes each
transmission unique, thus rendering code capture and
resend (code grabbing) schemes useless.
The encryption key, serial number, and conguration
data are stored in EEPROM which is not accessible via
any external connection. This makes the HCS301 a
very secure unit. The HCS301 provides an easy to use
serial interface for programming the necessary security
keys, system parameters, and conguration data.
1
2
3
4
8
7
6
5
S0
S1
S2
S3
VDD
LED
PWM
VSS
PDIP, SOIC
H
C
S
3
0
1
VSS
VDD
Oscillator
Reset circuit
LED driver
Controller
Power
latching
and
switching
Button input port
32-bit shift register
Encoder
EEPROM
PWM
LED
S
3
S
2
S
1
S
0
HCS301
Code Hopping Encoder
K
EELOQ
is a registered trademark of Microchip Technology, Inc.
Microchips Secure Data Products are covered by some or all of the following patents:
Code hopping encoder patents issued in Europe, U.S.A., and R.S.A. U.S.A.: 5,517,187; Europe: 0459781; R.S.A.: ZA93/4726
Secure learning patents issued in the U.S.A. and R.S.A. U.S.A.: 5,686,904; R.S.A.: 95/5429
HCS301
DS21143A-page 2
Preliminary
1997 Microchip Technology Inc.
The encryption keys and code combinations are pro-
grammable but read-protected. The keys can only be
veried after an automatic erase and programming
operation. This protects against attempts to gain
access to keys and manipulate synchronization values.
The HCS301 operates over a wide voltage range of
3.5 volts to 13.0 volts and has four button inputs in an
8-pin conguration. This allows the system designer
the freedom to utilize up to 15 functions. The only
components required for device operation are the but-
tons and RF circuitry, allowing a very low system cost.
1.0 SYSTEM OVERVIEW
Key Terms
Manufacturers code a 64-bit word, unique to
each manufacturer, used to produce a unique
encryption key in each transmitter (encoder).
Encryption Key a unique 64-bit key generated
and programmed into the encoder during the
manufacturing process. The encryption key
controls the encryption algorithm and is stored in
EEPROM on the encoder device.
1.1 Learn
The HCS product family facilitates several learn strate-
gies to be implemented on the decoder. The following
are examples of what can be done. It must be pointed
out that there exists some third-party patents on learn-
ing strategies and implementation.
The HCS301 is a code hopping encoder device that is
designed specically for keyless entry systems,
primarily for vehicles and home garage door openers.
It is meant to be a cost-effective, yet secure solution to
such systems. The encoder portion of a keyless entry
system is meant to be held by the user and operated to
gain access to a vehicle or restricted area. The
HCS301 requires very few external components
(Figure 2-1).
1.1.1 NORMAL LEARN
The receiver uses the same information that is trans-
mitted during normal operation to derive the transmit-
ters secret key, decrypt the discrimination value and
the synchronization counter.
1.1.2 SECURE LEARN*
The transmitter is activated through a special button
combination to transmit a stored 48-bit value (random
seed) that can be used for key generation or be part of
the key. Transmission of the random seed can be dis-
abled after learning is completed.
Most low-end keyless entry systems transmit the same
code from a transmitter every time a button is pushed.
The relative number of code combinations for a low end
system is also a relatively small number. These
shortcomings provide the means for a sophisticated
thief to create a device that grabs a transmission and
re-transmits it later, or a device that scans all possible
combinations until the correct one is found.
The HCS301 employs the K
EE
L
OQ
code hopping
encryption algorithm to achieve a high level of security.
Code hopping is a method by which the code
transmitted from the transmitter to the receiver is
different every time a button is pushed. This method,
coupled with a transmission length of 66 bits, virtually
eliminates the use of code grabbing or code
scanning.
As indicated in the block diagram on page one, the
HCS301 has a small EEPROM array which must be
loaded with several parameters before use. The most
important of these values are:
A 28-bit serial number which is meant to be
unique for every encoder
An encryption key that is generated at the time of
production
A 16-bit synchronization value
The serial number for each transmitter is programmed
by the manufacturer at the time of production. The
generation of the encryption key is done using a key
generation algorithm (Figure 1-1). Typically, inputs to
the key generation algorithm are the serial number of
the transmitter and a 64-bit manufacturers code. The
manufacturers code is chosen by the system
manufacturer and must be carefully controlled. The
manufacturers code is a pivotal part of the overall
system security.
FIGURE 1-1: CREATION AND STORAGE OF ENCRYPTION KEY DURING PRODUCTION
Transmitter
Manufacturers
Serial Number
Code
Encryption
Key
Key
Generation
Algorithm
Serial Number
Encryption Key
Sync Counter
.
.
.
HCS301 EEPROM Array
1997 Microchip Technology Inc.
Preliminary
DS21143A-page 3
HCS301
The 16-bit synchronization value is the basis for the
transmitted code changing for each transmission, and
is updated each time a button is pressed. Because of
the complexity of the code hopping algorithm, a change
in one bit of the synchronization value will result in a
large change in the actual transmitted code. There is a
relationship (Figure 1-2) between the key values in
EEPROM and how they are used in the encoder. Once
the encoder detects that a button has been pressed,
the encoder reads the button and updates the synchro-
nization counter. The synchronization value is then
combined with the encryption key in the encryption
algorithm and the output is 32 bits of encrypted infor-
mation. This data will change with every button press,
hence, it is referred to as the hopping portion of the
code word. The 32-bit hopping code is combined with
the button information and the serial number to form
the code word transmitted to the receiver. The code
word format is explained in detail in Section 4.3.
Any type of controller may be used as a receiver, but it
is typically a microcontroller with compatible rmware
that allows the receiver to operate in conjunction with a
transmitter, based on the HCS301. Section 7.0
provides more detail on integrating the HCS301 into a
total system.
Before a transmitter can be used with a particular
receiver, the transmitter must be learned by the
receiver. Upon learning a transmitter, information is
stored by the receiver so that it may track the
transmitter, including the serial number of the
transmitter, the current synchronization value for that
transmitter and the same encryption key that is used on
the transmitter. If a receiver receives a message of
valid format, the serial number is checked and, if it is
from a learned transmitter, the message is decrypted
and the decrypted synchronization counter is checked
against what is stored. If the synchronization value is
veried, then the button status is checked to see what
operation is needed. Figure 1-3 shows the relationship
between some of the values stored by the receiver and
the values received from the transmitter.
FIGURE 1-2: BASIC OPERATION OF TRANSMITTER (ENCODER)
FIGURE 1-3: BASIC OPERATION OF RECEIVER (DECODER)
KEELOQ
Algorithm
Button Press
Information
Encryption
EEPROM Array
32 Bits of
Encrypted Data
Serial Number
Transmitted Information
Encryption Key
Sync Counter
Serial Number
Button Press
Information
EEPROM Array
Encryption Key
32 Bits of
Encrypted Data
Serial Number
Received Information
Decrypted
Synchronization
Counter
Check for
Match
Check for
Match
KEELOQ
Algorithm
Encryption
Sync Counter
Serial Number
Manufacturer Code
HCS301
DS21143A-page 4
Preliminary
1997 Microchip Technology Inc.
2.0 DEVICE OPERATION
As shown in the typical application circuits (Figure 2-1),
the HCS301 is a simple device to use. It requires only
the addition of buttons and RF circuitry for use as the
transmitter in your security application. A description of
each pin is described in Table 2-1.
FIGURE 2-1: TYPICAL CIRCUITS
TABLE 2-1: PIN DESCRIPTIONS
Note:
When V
DD
> 9.0V and driving low capacitive
loads, a resistor with a minimum value of 50
W
should be used in line with V
DD
. This prevents
clamping of PWM at 9.0V in the event of PWM
overshoot.
Name
Pin
Number
Description
S0 1 Switch input 0
S1 2 Switch input 1
S2 3 Switch input 2/Can also be clock
pin when in programming mode
S3 4 Switch input 3/Clock pin when in
programming mode
V
SS
5 Ground reference connection
PWM 6 Pulse width modulation (PWM)
output pin/Data pin for
programming mode
LED 7 Cathode connection for directly
driving LED during transmission
V
DD
8 Positive supply voltage
connection
VDD
B0
Tx out
S0
S1
S2
S3
LED
VDD
PWM
VSS
2 button remote control
B1
VDD
Tx out
S0
S1
S2
S3
LED
VDD
PWM
VSS
5 button remote control (Note1)
B4 B3 B2 B1 B0
Note 1: Up to 15 functions can be implemented by pressing
more than one button simultaneously or by using a
suitable diode array.
2: Resistor (R) is recommended for current limiting.
+12V
R
+12V
R
(Note 2)
(Note 2)
The high security level of the HCS301 is based on the pat-
ented K
EE
L
OQ
technology. A block cipher based on a block
length of 32 bits and a key length of 64 bits is used. The
algorithm obscures the information in such a way that even
if the transmission information (before coding) differs by
only 1 bit from the information in the previous transmis-
sion, the next coded transmission will be totally different.
Statistically, if only 1 bit in the 32-bit string of information
changes, approximately 50 percent of the coded transmis-
sion will change. The HCS301 will wake up upon detecting
a switch closure and then delay approximately 10 ms for
switch debounce (Figure 2-2). The synchronization infor-
mation, xed information, and switch information will be
encrypted to form the hopping code. The encrypted or
hopping code portion of the transmission will change every
time, even if the same button is pushed again. A code that
has been transmitted will not occur again for more than
64K transmissions. This will provide more than 18 years of
typical use before a code is repeated, based on 10 opera-
tions per day. Overow information sent from the encoder
can be used by the decoder to extend the number of
unique transmissions to more than 192K.
If, in the transmit process, it is detected that a new but-
ton(s) has been pressed, a reset will immediately be
forced and the code word will not be completed. Please
note that buttons removed will not have any effect on the
code word unless no buttons remain pressed. In this case,
the code word will be completed and the power down will
occur.
FIGURE 2-2: ENCODER OPERATION
Power Up
Reset and Debounce Delay
(10 ms)
Sample Inputs
Update Sync Info
Encrypt With
Load Transmit Register
Buttons
Added?
All
Buttons
Released?
(A button has been pressed)
Transmit
Stop
No
Yes
No
Yes
Encryption Key
Complete Code
Word Transmission
1997 Microchip Technology Inc.
Preliminary
DS21143A-page 5
HCS301
3.0 EEPROM MEMORY
ORGANIZATION
The HCS301 contains 192 bits (12 x 16-bit words) of
EEPROM memory (Table 3-1). This EEPROM array is
used to store the encryption key information,
synchronization value, etc. Further descriptions of the
memory array is given in the following sections.
TABLE 3-1: EEPROM MEMORY MAP
3.1 Key_0 - Key_3 (64-Bit Encryption Key)
The 64-bit encryption key is used by the transmitter to
create the encrypted message transmitted to the
receiver. This key is created and programmed at the
time of production using a key generation algorithm.
The key generation algorithm is different from the
K
EE
L
OQ
algorithm, although it too is a proprietary
encryption method. Inputs to the key generation
algorithm are the serial number for the particular
transmitter being used and the 64-bit manufacturers
code. While the key generation algorithm supplied from
Microchip is the typical method used, a user may elect
to create their own method of key generation. This may
be done providing that the decoder is programmed with
the same means of creating the key for
decryption purposes.
WORD
ADDRESS
MNEMONIC DESCRIPTION
0 KEY_0 64-bit encryption key
(word 0)
1 KEY_1 64-bit encryption key
(word 1)
2 KEY_2 64-bit encryption key
(word 2)
3 KEY_3 64-bit encryption key
(word 3)
4 SYNC 16-bit synchronization
value
5 RESERVED Set to 0000H
6 SER_0 Device Serial Number
(word 0)
7 SER_1(Note) Device Serial Number
(word 1)
8 SEED_0 Seed Value (word 0)
9 SEED_1 Seed Value (word 1)
10 EN_KEY 16-bit Envelope Key
11 CONFIG Conguration Word
Note: The MSB of the serial number contains a bit
used to select the auto shutoff timer.
3.2 SYNC (Synchronization Counter)
This is the 16-bit synchronization value that is used to
create the hopping code for transmission. This value
will be changed after every transmission.
3.3 SER_0, SER_1 (Encoder Serial
Number)
SER_0 and SER_1 are the lower and upper words of
the device serial number, respectively. Although there
are 32 bits allocated for the serial number, only the
lower order 28 bits are transmitted. The serial number
is meant to be unique for every transmitter. The most
signicant bit of the serial number (Bit 31) is used to
turn the auto shutoff timer on or off.
3.3.1 AUTO-SHUTOFF TIMER SELECT
The most signicant bit of the serial number (Bit 31) is
used to turn the Auto-shutoff timer on or off. This timer
prevents the transmitter from draining the battery
should a button get stuck in the on position for a long
period of time. The time period is approximately
25 seconds, after which the device will go to the
Time-out mode. When in the Time-out mode, the
device will stop transmitting, although since some
circuits within the device are still active, the current
draw within the Shutoff mode will be more than Standby
mode. If the most signicant bit in the serial number is
a one, then the Auto-shutoff timer is enabled, and a
zero in the most signicant bit will disable the timer. The
length of the timer is not selectable.
3.4 SEED_0, SEED_1 (Seed Word)
This is the two-word (32 bits) seed code that will be
transmitted when all four buttons are pressed at the same
time. This allows the system designer to implement the
secure learn feature or use this xed code word as part of
a different key generation/tracking process.
3.5 EN_Key (Envelope Encryption Key)
Envelope encryption is a selectable option that
encrypts the portion of the transmission that contains
the transmitter serial number and function code.
Selecting this option is done by setting the appropriate
bit in the conguration word (Table 3-2). Normally, the
serial number and function code are transmitted in the
clear (unencrypted), but for an added level of security,
the system designer may elect to implement this
option. The envelope encryption key is used to encrypt
the serial number and function code portion of the
transmission, if the envelope encryption option has
been selected. The envelope encryption algorithm is a
different algorithm than the key generation or transmit
encryption algorithm. The EN_key is typically a random
number and the same for all transmitters in a system.
HCS301
DS21143A-page 6
Preliminary
1997 Microchip Technology Inc.
3.6 Conguration Word
The conguration word is a 16-bit word stored in
EEPROM array that is used by the device to store
information used during the encryption process, as well
as the status of option congurations. Further
explanations of each of the bits are described in the
following sections.
TABLE 3-2: CONFIGURATION WORD
3.6.1 DISCRIMINATION VALUE
(DISC0 TO DISC9)
The discrimination value can be programmed with any
value to serve as a post decryption check on the
decoder end. In a typical system, this will be
programmed with the 10 least signicant bits of the
serial number or a constant value, which will also be
stored by the receiver system after a transmitter has
been learned. The discrimination bits are part of the
information that is to form the encrypted portion of the
transmission. After the receiver has decrypted a trans-
mission, the discrimination bits can be checked against
the stored value to verify that the decryption process
was valid.
3.6.2 OVERFLOW BITS (OVR0 AND OVR1)
The overow bits are used to extend the number of pos-
sible synchronization values. The synchronization
counter is 16 bits in length, yielding 65,536 values
before the cycle repeats. Under typical use of
10 operations a day, this will provide nearly 18 years of
use before a repeated value will be used. Should the
system designer conclude that is not adequate, then
the overow bits can be utilized to extend the number
of unique values. This can be done by programming
OVR0 and OVR1 to 1s at the time of production. The
encoder will automatically clear OVR0 the rst time that
the synchronization value wraps from 0xFFFF to
Bit Number Bit Description
0 Discrimination Bit 0
1 Discrimination Bit 1
2 Discrimination Bit 2
3 Discrimination Bit 3
4 Discrimination Bit 4
5 Discrimination Bit 5
6 Discrimination Bit 6
7 Discrimination Bit 7
8 Discrimination Bit 8
9 Discrimination Bit 9
10 Overow Bit 0 (OVR0)
11 Overow Bit 1 (OVR1)
12 Low Voltage Trip Point Select
13 Baudrate Select Bit 0 (BSL0)
14 Baudrate Select Bit 1 (BSL1)
15 Envelope Encryption Select (EENC)
0x0000 and clear OVR1 the second time the counter
wraps. Once cleared, OVR0 and OVR1 cannot be set
again, thereby creating a permanent record of the
counter overow. This prevents fast cycling of 64K
counter. If the decoder system is programmed to track
the overow bits, then the effective number of unique
synchronization values can be extended to 196,608.
3.6.3 ENVELOPE ENCRYPTION (EENC)
If the EENC bit is set to a 1, the serial number and func-
tion code will also be encrypted so that it will appear to
be random. The 16-bit envelope key and envelope
algorithm will be used for encryption.
3.6.4 BAUDRATE SELECT BITS (BSL0, BSL1)
BSL0 and BSL1 select the speed of transmission and
the code word blanking. Table 3-3 shows how the bits
are used to select the different baud rates and
Section 5.2 provides detailed explanation in code word
blanking.
TABLE 3-3: BAUDRATE SELECT
BSL1 BSL0
Basic Pulse
Element
Code Words
Transmitted
0 0 400
m
s All
0 1 200
m
s 1 out of 2
1 0 100
m
s 1 out of 2
1 1 100
m
s 1 out of 4
1997 Microchip Technology Inc.
Preliminary
DS21143A-page 7
HCS301
3.6.5 LOW VOLTAGE TRIP POINT SELECT
The low voltage trip point select bit is used to tell the
HCS301 what V
DD
level is being used. This information
will be used by the device to determine when to send
the voltage low signal to the receiver. When this bit is
set to a one, the V
DD
level is assumed to be operating
from a 9.0 volt or 12.0 volt V
DD
level. If the bit is set low,
then the V
DD
level is assumed to be 6.0 volts. Refer to
Figure 3-1 for voltage trip point.
The LED current limiting resistor value also affects the
LED current:
V
LOW
is tested at 3.5V and 13.0V.
FIGURE 3-1: TYPICAL VOLTAGE TRIP
POINTS (BY
CHARACTERIZATION)
V
LOW
=
1 (high limiting).
V
LOW
=
0 (low limiting).
-40 20 40 100
8.5
7.5
8.0
7.0
9.0
2.5
3.0
3.5
4.0
VLOW
Temp (C)
Volts (V)
VLOW sel = 1
VLOW sel = 0
4.5
-20 0 60 80
5.0
5.5
Max
Min
Max
Min
4.0 TRANSMITTED WORD
4.1 Transmission Format
The HCS301 transmission is made up of several parts
(Figure 4-1). Each transmission is begun with a
preamble and a header, followed by the encrypted and
then the xed data. The actual data is 66 bits which
consists of 32 bits of encrypted data and 34 bits of xed
data. Each transmission is followed by a guard period
before another transmission can begin. Refer to
Table 8-4 for transmission timing requirements. The
encrypted portion provides up to four billion changing
code combinations and includes the button status bits
(based on which buttons were activated) along with the
synchronization counter value and some discrimination
bits. The xed portion is comprised of the status bits,
the function bits and the 28-bit serial number. The xed
and encrypted sections combined increase the number
of combinations to 7.38 x 10
19
.
4.2 Synchronous Transmission Mode
Synchronous transmission mode can be used to clock
the code word out using an external clock.
To enter synchronous transmission mode, the pro-
gramming mode start-up sequence must be executed
as shown in Figure 4-3. If either S1 or S0 is set on the
falling edge of S2 (or S3), the device enters synchro-
nous transmission mode. In this mode, it functions as a
normal transmitter, with the exception that the timing of
the PWM data string is controlled externally and that 16
extra bits are transmitted at the end with he code word.
The button code will be the S0, S1 value at the falling
edge S2 or S3. The timing of the PWM data string is
controlled by supplying a clock on S2 or S3 and should
not exceed 20 KHz. The code word is the same as in
PWM mode with 16 reserved bits at the end of the
word. The reserved bits can be ignored. When in syn-
chronous transmission mode S2 or S3 should not be
toggled until all internal processing has been com-
pleted as shown in Figure 4-4.
4.3 Code Word Organization
The HCS301 transmits a 66-bit code word when a
button is pressed. The 66-bit word is constructed from
a Fixed Code portion and an Encrypted Code portion
(Figure 4-2).
The
Encrypted Data
is generated from 4 button bits, 2
overow counter bits, 10 discrimination bits and the
16-bit sync value (Figure 8-5).
The
Fixed Code Data
is made up from two status bits,
four button bits and the 28-bit serial number. The four
button bits and the 28-bit serial number may be
encrypted with the Envelope Key if the envelope
encryption is enabled by the user.
HCS301
DS21143A-page 8
Preliminary
1997 Microchip Technology Inc.
FIGURE 4-1: CODE WORD TRANSMISSION FORMAT
FIGURE 4-2: CODE WORD ORGANIZATION
FIGURE 4-3: SYNCHRONOUS TRANSMISSION MODE
FIGURE 4-4: TRANSMISSION WORD FORMAT DURING SYNCHRONOUS TRANSMISSION MODE
LOGIC 0
LOGIC 1
Bit
Period
Preamble Header
Encrypted Portion
of Transmission
Fixed Portion of
Transmission
Guard
Time
TP TH
THOP TFIX TG
Repeat
(1 bit)
VLOW
(1 bit)
Button
Status
(4 bits)
28-bit
Serial Number
Button
Status
(4 bits)
Discrimina-
tion bits
(12 bits)
16-bit
Sync Value
1 bit of Status
1 bit Fixed
+
Serial Number and
Button Status (32 bits)
+
32 bits of Encrypted Data
Fixed Code Data Encrypted Code Data
66 bits
of Data
Transmitted
t = 50 ms
01,10,11
PWM
S2(S3)
S[1:0]
16 2 4 28 16 16
Transmission Direction
Reserved Padding
Button
Code Serial Number Data Word Sync Counter
1997 Microchip Technology Inc. Preliminary DS21143A-page 9
HCS301
5.0 SPECIAL FEATURES
5.1 Code Word Completion
Code word completion is an automatic feature that
makes sure that the entire code word is transmitted,
even if the button is released before the transmission is
complete. The HCS301 encoder powers itself up when
a button is pushed and powers itself down after the
command is nished, if the user has already released
the button. If the button is held down beyond the time
for one transmission, then multiple transmissions will
result. If another button is activated during a
transmission, the active transmission will be aborted
and the new code will be generated using the new
button information.
5.2 Blank Alternate Code Word
Federal Communications Commission (FCC) part 15
rules specify the limits on fundamental power and
harmonics that can be transmitted. Power is calculated
on the worst case average power transmitted in a
100ms window. It is therefore advantageous to
minimize the duty cycle of the transmitted word. This
can be achieved by minimizing the duty cycle of the
individual bits and by blanking out consecutive words.
Blank Alternate Code Word (BACW) is used for
reducing the average power of a transmission
(Figure 5-1). This is a selectable feature that is
determined in conjunction with the baudrate selection
bits BSL0 and BSL1. Using the BACW allows the user
to transmit a higher amplitude transmission if the
transmission length is shorter. The FCC puts
constraints on the average power that can be
transmitted by a device, and BACW effectively prevents
continuous transmission by only allowing the transmis-
sion of every second or every fourth code word. This
reduces the average power transmitted and hence,
assists in FCC approval of a transmitter device.
5.3 Envelope Encryption Option
Envelope Encryption is a user selectable option which
is meant to offer a higher level of security for a code
hopping system. During a normal transmission with the
envelope encryption turned off, the 28-bit serial
number and function code are transmitted in the clear
(unencrypted). If envelope encryption is selected, then
the serial number and function code are also encrypted
before transmission. The encryption for the serial num-
ber is done using a different algorithm than the trans-
mission algorithm. The envelope encryption scheme is
not nearly as complex as the KEELOQ algorithm and,
hence, not as secure. When the envelope encryption is
used, the serial number must be decrypted using the
envelope key and envelope decryption. After the serial
number is obtained, the normal decryption method can
be used to decrypt the hopping code.
FIGURE 5-1: BLANK ALTERNATE CODE WORD (BACW)
One Code Word
BACW Disabled
(All words transmitted)
BACW Enabled
(1 out of 2 transmitted)
BACW Enabled
(1 out of 4 transmitted)
A
2A
4A
100ms 100ms 100ms
100ms
Amplitude
Time
HCS301
DS21143A-page 10 Preliminary 1997 Microchip Technology Inc.
5.4 Secure Learn
In order to increase the level of security in a system, it is
possible for the receiver to implement what is known as
a secure learn function. This can be done by utilizing the
seed value on the HCS301 which is stored in EEPROM
and can only be transmitted when all four button inputs
are pressed at the same time (Table 5-1). Instead of the
normal key generation method being used to create the
encryption key, this seed value is used.
TABLE 5-1: PIN ACTIVATION TABLE
5.5 Auto-shutoff
The Auto-shutoff function automatically stops the
device from transmitting if a button inadvertently gets
pressed for a long period of time. This will prevent the
device from draining the battery if a button gets
pressed while the transmitter is in a pocket or purse.
This function can be enabled or disabled and is
selected by setting or clearing the Auto-shutoff bit
(Section 3.3.1). Setting this bit high will enable the
function (turn Auto-shutoff function on) and setting the
bit low will disable the function. Time-out period is
approximately 25 seconds.
S3 S2 S1 S0 Notes
1 0 0 0 1 1
2 0 0 1 0 1
3 0 0 1 1 1
4 0 1 0 0 1
5 0 1 0 1 1
6 0 1 1 0 1
7 0 1 1 1 1
8 1 0 0 0 1
9 1 0 0 1 1
10 1 0 1 0 1
11 1 0 1 1 1
12 1 1 0 0 1
13 1 1 0 1 1
14 1 1 1 0 1
15 1 1 1 1 2
Note 1: Transmit generated 32-bit code hopping
word.
2: Transmit 32-bit seed value.
5.6 VLOW: Voltage LOW indicator
The VLOW bit is transmitted with every transmission
(Figure 8-5) and will be transmitted as a one if the
operating voltage has dropped below the low voltage
trip point. The trip point is selectable between two
values, based on the battery voltage being used. See
Section 3.6.5 for a description of how the low voltage
select option is set. This VLOW signal is transmitted so
the receiver can alert the user that the transmitter bat-
tery is low.
5.7 RPT: Repeat indicator
This bit will be low for the rst transmitted word. If a
button is held down for more than one transmitted code
word, this bit will be set to indicate a repeated code
word and remain set until the button is released.
5.8 LED Output Operation
During normal transmission the LED output is LOW. If
the supply voltage drops below the low voltage trip
point, the LED output will be toggled at approximately
5 Hz during the transmission (Section 3.6.5). The limit-
ing resistor is selectable between two nominal values
(Section 3.6.5).
1997 Microchip Technology Inc. Preliminary DS21143A-page 11
HCS301
6.0 PROGRAMMING THE HCS301
When using the HCS301 in a system, the user will have
to program some parameters into the device including
the serial number and the secret key before it can be
used. The programming cycle allows the user to input
all 192 bits in a serial data stream, which are then
stored internally in EEPROM. Programming will be
initiated by forcing the PWM line high, after the S3 line
has been held high for the appropriate length of time
line (Table 6-1 and Figure 6-1). After the program mode
is entered, a delay must be provided to the device for
the automatic bulk write cycle to complete. This will
write all locations in the EEPROM to an all zeros pat-
tern. The device can then be programmed by clocking
in 16 bits at a time, using S3 as the clock line and PWM
as the data in line. After each 16-bit word is loaded, a
programming delay is required for the internal program
cycle to complete. This delay can take up to Twc. At the
end of the programming cycle, the device can be veri-
ed (Figure 6-2) by reading back the EEPROM. Read-
ing is done by clocking the S3 line and reading the data
bits on PWM. For security reasons, it is not possible to
execute a verify function without rst programming the
EEPROM. A verify operation can only be done
immediately following the program cycle.
Note: To ensure that the device does not acci-
dentally enter programming mode (result-
ing in a bulk erase), PWM should never be
pulled high by the circuit connected to it.
Special care should be taken when driving
PNP RF transistors.
FIGURE 6-1: PROGRAMMING WAVEFORMS
FIGURE 6-2: VERIFY WAVEFORMS
TABLE 6-1: PROGRAMMING/VERIFY TIMING REQUIREMENTS
VDD = 5.0V 10%
25 C 5 C
Parameter Symbol Min. Max. Units
Program mode setup time TPS 3.5 4.5 ms
Hold time 1 TPH1 3.5 ms
Hold time 2 TPH2 50 ms
Bulk Write time TPBW 2.2 ms
Program delay time TPROG 2.2 ms
Program cycle time TWC 36 ms
Clock low time TCLKL 25 ms
Clock high time TCLKH 25 ms
Data setup time TDS 0 ms
Data hold time TDH 18 ms
Data out valid time TDV 10 24 ms
PWM
Enter Program
Mode
(Data)
(Clock)
Bit 0 Bit 1 Bit 2 Bit 3 Bit 14 Bit 15 Bit 16 Bit 17
TPH1
TPBW
TPS
Repeat 12 times for each word
TPH2
TCLKH
TCLKL
TWC TDS
S3
Data for Word 0 (KEY_0) Data for Word 1
TDH
Note 1: Unused button inputs to be held ground during the entire programming sequence.
2: The VDD pin must be taken to ground after a programming/verify cycle.
PWM
(Clock)
(Data)
End of
Programming Cycle
Begin Verify Cycle Here
Bit 1 Bit 2 Bit 3 Bit 15 Bit 14 Bit 16 Bit 17 Bit190 Bit191
TWC
Data in Word 0
TDV
S3
Bit 0 Bit191 Bit190
Note: If a verify operation is to be done, then it must immediately follow the program cycle.
HCS301
DS21143A-page 12 Preliminary 1997 Microchip Technology Inc.
7.0 INTEGRATING THE HCS301
INTO A SYSTEM
Use of the HCS301 in a system requires a compatible
decoder. This decoder is typically a microcontroller with
compatible rmware. Microchip will provide (via a
license agreement) rmware routines that accept
transmissions from the HCS301 and decrypt the
hopping code portion of the data stream. These
routines provide system designers the means to
develop their own decoding system.
7.1 Learning a transmitter to a receiver
In order for a transmitter to be used with a decoder, the
transmitter must rst be learned. Several learning
strategies can be followed in the decoder implementa-
tion. When a transmitter is learned to a decoder, it is
suggested that the decoder stores the serial number
and current synchronization value in EEPROM. The
decoder must keep track of these values for every
transmitter that is learned (Figure 7-1). The maximum
number of transmitters that can be learned is only a
function of how much EEPROM memory storage is
available. The decoder must also store the manufac-
turers code in order to learn a transmission transmitter,
although this value will not change in a typical system
so it is usually stored as part of the microcontroller
ROM code. Storing the manufacturers code as part of
the ROM code is also better for security reasons.
It must be stated that some learning strategies have
been patented and care must be taken not to infringe.
FIGURE 7-1: TYPICAL LEARN SEQUENCE
Enter Learn
Mode
Wait for Reception
of a Valid Code
Generate Key
from Serial Number
Use Generated Key
to Decrypt
Compare Discrimination
Value with Fixed Value
Equal
Wait for Reception
of Second Valid Code
Compare Discrimination
Value with Fixed Value
Use Generated Key
to Decrypt
Equal
Counters
Encryption key
Serial number
Synchronization counter
Sequential
?
?
?
Exit
Learn successful Store:
Learn
Unsuccessful
No
No
No
Yes
Yes
Yes
1997 Microchip Technology Inc. Preliminary DS21143A-page 13
HCS301
7.2 Decoder operation
In a typical decoder operation (Figure 7-2), the key
generation on the decoder side is done by taking the
serial number from a transmission and combining that
with the manufacturers code to create the same secret
key that was used by the transmitter. Once the secret
key is obtained, the rest of the transmission can be
decrypted. The decoder waits for a transmission and
immediately can check the serial number to determine
if it is a learned transmitter. If it is, it takes the encrypted
portion of the transmission and decrypts it using the
stored key. It uses the discrimination bits to determine
if the decryption was valid. If everything up to this point
is valid, the synchronization value is evaluated.
FIGURE 7-2: TYPICAL DECODER
OPERATION
?
Transmission
Received
Does
Serial Number
Match
?
Decrypt Transmission
Is
Decryption
Valid
?
Is
Counter
Within 16
?
Is
Counter
Within 32K
?
Update
Counter
Execute
Command
Save Counter
in Temp Location
Start
No
No
No
No
Yes
Yes
Yes
Yes
Yes
No
and
No
7.3 Synchronization with Decoder
The KEELOQ
technology features a sophisticated
synchronization technique (Figure 7-3) which does not
require the calculation and storage of future codes. If
the stored counter value for that particular transmitter
and the counter value that was just decrypted are
within a formatted window of say 16, the counter is
stored and the command is executed. If the counter
value was not within the single operation window, but is
within the double operation window of say 32K window,
the transmitted synchronization value is stored in tem-
porary location and it goes back to waiting for another
transmission. When the next valid transmission is
received, it will check the new value with the one in tem-
porary storage. If the two values are sequential, it is
assumed that the counter had just gotten out of the sin-
gle operation window, but is now back in sync, so the
new synchronization value is stored and the command
executed. If a transmitter has somehow gotten out of
the double operation window, the transmitter will not
work and must be re-learned. Since the entire window
rotates after each valid transmission, codes that have
been used are part of the blocked (32K) codes and are
no longer valid. This eliminates the possibility of grab-
bing a previous code and re-transmitting to gain entry.
FIGURE 7-3: SYNCHRONIZATION WINDOW
Note: The synchronization method described in
this section is only a typical implementation
and because it is usually implemented in
rmware, it can be altered to t the needs
of a particular system
Blocked 32K
Codes
Open 32K
Codes
Entire Window
rotates to eliminate
use of previously
used codes
Current window
of 16 codes
Current
Position
HCS301
DS21143A-page 14 Preliminary 1997 Microchip Technology Inc.
8.0 ELECTRICAL CHARACTERISTICS
TABLE 8-1: ABSOLUTE MAXIMUM RATINGS
TABLE 8-2: DC CHARACTERISTICS
Symbol Item Rating Units
VDD Supply voltage -0.3 to 13.3 V
VIN Input voltage -0.3 to 13.3 V
VOUT Output voltage -0.3 to VDD + 0.3 V
IOUT Max output current 25 mA
TSTG Storage temperature -55 to +125 C (Note)
TLSOL Lead soldering temp 300 C (Note)
VESD ESD rating 4000 V
Note: Stresses above those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the
device.
Commercial (C): Tamb = 0C to +70C
Industrial (I): Tamb = -40C to +85C
3.5V < VDD < 13.0V
Parameter Sym. Min Typ* Max Unit Conditions
Operating current (avg) ICC 0.6
1.5
8.0
1.0
3.0
12.0
mA
VDD = 3.5V
VDD = 6.6V
VDD = 13.0V
(Figure 8-1)
Standby current ICCS 1 10 mA
High level Input voltage VIH 0.4 VDD VDD+
0.3
V
Low level input voltage VIL -0.3 0.15 VDD V
High level output voltage VOH 0.5VDD V IOH = -2 mA
Low level output voltage VOL 0.08 VDD V IOL = 2 mA
LED sink current ILED 3.5
2.7
4.7
3.7
5.9
4.6
mA VDD = 6.6V, Vlow source = 0
VDD = 13.0V, Vlow source = 1
Resistance; S0-S3 RS0-3 40 60 80 KW VIN = 4.0V
Resistance; PWM RPWM 80 120 160 KW VIN = 4.0V
* Typical values are at 25C.
1997 Microchip Technology Inc. Preliminary DS21143A-page 15
HCS301
FIGURE 8-1: TYPICAL ICC CURVE OF HCS301 WITH EXTERNAL RESISTORS
2 3 4 5 6 7 8 9 11 12 13 10
m
A
0.0
2.0
4.0
6.0
8.0
10.0
12.0
VBAT [V]
2 3 4 5 6 7 8 9 11 12 13 10
m
A
0.0
2.0
4.0
6.0
8.0
10.0
12.0
VBAT [V]
2 3 4 5 6 7 8 9 11 12 13 10
m
A
0.0
2.0
4.0
6.0
8.0
10.0
12.0
VBAT [V]
50W External
1K External
2K External
Typical
Maximum
Minimum
LEGEND
HCS301
DS21143A-page 16 Preliminary 1997 Microchip Technology Inc.
FIGURE 8-2: POWER UP AND TRANSMIT TIMING
TABLE 8-3: POWER UP AND TRANSMIT TIMING REQUIREMENTS
FIGURE 8-3: PWM FORMAT
FIGURE 8-4: PREAMBLE/HEADER FORMAT
VDD = +3.5 to13.0V
Commercial (C): Tamb = 0C to +70C
Industrial (I): Tamb = -40C to +85C
Parameter Symbol Min Max Unit Remarks
Time to second button press TBP 10 + Code
Word Time
25 + Code
Word Time
ms (Note 1)
Transmit delay from button detect TTD 10 25 ms
Debounce delay TDB 6 15 ms
Auto-shutoff time-out period TTO 20 40 s (Note 2)
Note 1: TBP is the time in which a second button can be pressed without completion of the rst code word and the
intention was to press the combination of buttons.
2: The auto shutoff timeout period is not tested.
Button Press
Sn
Detect
TDB
PWM
TTD
Code Word Transmission
TTO
Code
Word
1
Code
Word
2
Code
Word
3
Code
Word
n
TBP
LOGIC 0
LOGIC 1
Preamble Header
Encrypted Portion
of Transmission
Fixed portion of
Transmission
Guard
Time
TP TH
THOP TFIX TG
TBP
TE TE TE
Preamble Header
P0 P12
23 TE 10 TE
Data Word
Transmission
Bit 0 Bit 1
1997 Microchip Technology Inc. Preliminary DS21143A-page 17
HCS301
FIGURE 8-5: DATA WORD FORMAT
TABLE 8-4: CODE WORD TRANSMISSION TIMING REQUIREMENTS
FIGURE 8-6: HCS301 TE VS. TEMP (BY CHARACTERIZATION ONLY)
VDD = +3.5 to 13.0
Commercial (C): Tamb = 0C to +70C
Industrial (I): Tamb = -40C to +85C
Code Words Transmitted
All 1 out of 2 1 out of 4
Symbol Characteristic
Number
of TE
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units
TE Basic pulse element 1 280 400 620 140 200 310 70 100 155 ms
TBP PWM bit pulse width 3 840 1200 1860 420 600 930 210 300 465 ms
TP Preamble duration 23 6.4 9.2 14.3 3.2 4.6 7.1 1.6 2.3 3.6 ms
TH Header duration 10 2.8 4.0 6.2 1.4 2.0 3.1 0.7 1.0 1.6 ms
THOP Hopping code duration 96 26.9 38.4 59.5 13.4 19.2 29.8 6.7 9.6 14.9 ms
TFIX Fixed code duration 102 28.6 40.8 63.2 14.3 20.4 31.6 7.1 10.2 15.8 ms
TG Guard Time 39 10.9 15.6 24.2 5.5 7.8 12.1 2.7 3.9 6.0 ms
Total Transmit Time 270 75.6 108.0 167.4 37.8 54.0 83.7 18.9 27.0 41.9 ms
PWM data rate 1190 833 538 2381 1667 1075 4762 3333 2151 bps
Note: The timing parameters are not tested but derived from the oscillator clock.
Bit 0 Bit 1
Header
Bit 30 Bit 31 Bit 32 Bit 33 Bit 58 Bit 59
Fixed Code Word Hopping Code Word
Guard
LSB LSB MSB MSB S3 S0 S1 S2 VLOWRPT
Time
Serial Number Button Code Status
Bit 60 Bit 61 Bit 62 Bit 63 Bit 64 Bit 65
0.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.7
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
0.6
TE Min.
TE Max.
TE Max.
TE
TEMPERATURE
VDD = 3.5V
VDD 5.0V
VDD = 5.0V
VDD 5.0V
Typical
HCS301
DS21143A-page 18 Preliminary 1997 Microchip Technology Inc.
NOTES:
HCS301
1997 Microchip Technology Inc. Preliminary DS21143A-page 19
HCS301 PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales ofce.
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom-
mended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. Your local Microchip sales ofce
2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
3. The Microchip Worldwide Web Site (www.microchip.com)
Package:
P = Plastic DIP (300 mil Body), 8-lead
SN = Plastic SOIC (150 mil Body)
Temperature
Range:
Blank = 0C to +70C
I = 40C to +85C
Device: HCS301 Code Hopping Encoder
HCS301T Code Hopping Encoder (Tape and Reel)
HCS301 /P
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed
by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchips products
as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip
logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
1999 Microchip Technology Inc.
All rights reserved. 1999 Microchip Technology Incorporated. Printed in the USA. 11/99 Printed on recycled paper.
AMERICAS
Corporate Office
Microchip Technology Inc.
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-786-7200 Fax: 480-786-7277
Technical Support: 480-786-7627
Web Address: http://www.microchip.com
Atlanta
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Tel: 770-640-0034 Fax: 770-640-0307
Boston
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508-480-9990 Fax: 508-480-8575
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071 Fax: 630-285-0075
Dallas
Microchip Technology Inc.
4570 Westgrove Drive, Suite 160
Addison, TX 75248
Tel: 972-818-7423 Fax: 972-818-2924
Dayton
Microchip Technology Inc.
Two Prestige Place, Suite 150
Miamisburg, OH 45342
Tel: 937-291-1654 Fax: 937-291-9175
Detroit
Microchip Technology Inc.
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250 Fax: 248-538-2260
Los Angeles
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888 Fax: 949-263-1338
New York
Microchip Technology Inc.
150 Motor Parkway, Suite 202
Hauppauge, NY 11788
Tel: 631-273-5305 Fax: 631-273-5335
San Jose
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950 Fax: 408-436-7955
AMERICAS (continued)
Toronto
Microchip Technology Inc.
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905-405-6279 Fax: 905-405-6253
ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific
Unit 2101, Tower 2
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2-401-1200 Fax: 852-2-401-3431
Beijing
Microchip Technology, Beijing
Unit 915, 6 Chaoyangmen Bei Dajie
Dong Erhuan Road, Dongcheng District
New China Hong Kong Manhattan Building
Beijing 100027 PRC
Tel: 86-10-85282100 Fax: 86-10-85282104
India
Microchip Technology Inc.
India Liaison Office
No. 6, Legacy, Convent Road
Bangalore 560 025, India
Tel: 91-80-229-0061 Fax: 91-80-229-0062
Japan
Microchip Technology Intl. Inc.
Benex S-1 6F
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa 222-0033 Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Korea
Microchip Technology Korea
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea
Tel: 82-2-554-7200 Fax: 82-2-558-5934
Shanghai
Microchip Technology
RM 406 Shanghai Golden Bridge Bldg.
2077 Yanan Road West, Hong Qiao District
Shanghai, PRC 200335
Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
ASIA/PACIFIC (continued)
Singapore
Microchip Technology Singapore Pte Ltd.
200 Middle Road
#07-02 Prime Centre
Singapore 188980
Tel: 65-334-8870 Fax: 65-334-8850
Taiwan, R.O.C
Microchip Technology Taiwan
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
EUROPE
United Kingdom
Arizona Microchip Technology Ltd.
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44 118 921 5858 Fax: 44-118 921-5835
Denmark
Microchip Technology Denmark ApS
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45 4420 9895 Fax: 45 4420 9910
France
Arizona Microchip Technology SARL
Parc dActivite du Moulin de Massy
43 Rue du Saule Trapu
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Germany
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 Mnchen, Germany
Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Italy
Arizona Microchip Technology SRL
Centro Direzionale Colleoni
Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Milan, Italy
Tel: 39-039-65791-1 Fax: 39-039-6899883
11/15/99
WORLDWIDE SALES AND SERVICE
Microchip received QS-9000 quality system
certification for its worldwide headquarters,
design and wafer fabrication facilities in
Chandler and Tempe, Arizona in July 1999. The
Companys quality system processes and
procedures are QS-9000 compliant for its
PICmicro
8-bit MCUs, KEELOQ
code hopping
devices, Serial EEPROMs and microperipheral
products. In addition, Microchips quality
system for the design and manufacture of
development systems is ISO 9001 certified.