The document discusses the On Board Diagnostic (OBD) capabilities of newer central locking systems. It describes the two pneumatic circuits that control locking points and how the safety version works. It also outlines the process for initiating an OBD check using the VAG1551 Scan Tool to check the DTC memory, diagnose issues, and erase codes if faults are repaired. Common diagnostic trouble codes for central locking systems are listed.
The document discusses the On Board Diagnostic (OBD) capabilities of newer central locking systems. It describes the two pneumatic circuits that control locking points and how the safety version works. It also outlines the process for initiating an OBD check using the VAG1551 Scan Tool to check the DTC memory, diagnose issues, and erase codes if faults are repaired. Common diagnostic trouble codes for central locking systems are listed.
The document discusses the On Board Diagnostic (OBD) capabilities of newer central locking systems. It describes the two pneumatic circuits that control locking points and how the safety version works. It also outlines the process for initiating an OBD check using the VAG1551 Scan Tool to check the DTC memory, diagnose issues, and erase codes if faults are repaired. Common diagnostic trouble codes for central locking systems are listed.
General Information The new generation of central locking is capable of On Board Diagnostic. Use of DTC memory, Output Diagnostic Test Mode and Read Measuring Value Block facilitates the search for malfunctions. The central locking system variation can also be coded using the VAG1551 Scan Tool (ST). Central locking has two pneumatic circuits. For central locking without keyless entry, the first circuit controls only the fuel filler flap; for central locking with the keyless entry system, the first circuit controls both the fuel filler flap and the driver-side door. The second circuit controls all remaining locking points. On the safety-version of central locking, if the driver-side (or passenger-side door) is unlocked with a single command, then only that door and the first pneumatic circuit are opened. If there is another unlocking command within 5 seconds, the second pneumatic circuit is also triggered and the whole vehicle is unlocked. If the rear lock cylinder is triggered only once, all doors will remain locked. The rear lid (or tailgate) will automatically re-lock itself after about 5 seconds. Page 1of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Interior lighting will gradually increase in intensity until fully illuminated (within about 1.5 seconds) when unlocking (fades off when locking). Page 2of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-70
The control of the luggage compartment lighting proceeds from the central locking pump to the rear lid (or tailgate) contact switch. The lighting will be switched off while the rear lid is open when a certain speed threshold is surpassed (about 5 km/h) or after 10 minutes. The new remote transmitter now uses radio frequency. For vehicles using the radio frequency remote locking system, the receiver is integrated into the central locking pump. The remote locking antenna is integrated into the wiring harness. If no doors (or the rear lid) have been opened within 60 seconds after the central locking system is triggered via radio frequency, central locking automatically relocks everything. If the anti-theft alarm system is armed, central locking cannot be opened via internal buttons. All vehicles with an anti-theft system are equipped with an ultrasonic interior monitoring system. This could be an interior monitor of the 1st generation (without OBD) or of the 2nd generation (with OBD). All that is necessary is the proper coding of the central locking system page 01-91 . Confirmation can be received from central locking as to whether the alarm system has been armed while locking the doors. The confirmation can be signalled by means of a short anti-theft Page 3of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 horn signal or by a brief flashing of the emergency flashers. Central locking can also be coded to give no confirmation at all. Activation of keyless entry can be signalled by a flashing of the emergency flashers. Page 4of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-71
Central Locking On Board Diagnostic (OBD), initiating Requirements
If the display remains blank, check VAG1551 voltage supply according to wiring diagram,
The Scan Tool (ST) HELP button can provide additional operating instruction.
The button is used to advance through the program sequence.
If an incorrect entry is made, press the -C- button to escape. Page 5of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3
- Switch printer on by pressing PRINT button (indicator lamp in button lights up).
- Press button -1- to select "Rapid data transfer" operating mode 1. Rapi d data transfer HELP Insert address word XX
Indicated on display Page 6of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-72
Address word for central locking: 35
- Press buttons -3- and -5- to insert "Central Locking" address word 35. Rapi d data transfer Q 35 - Central Locking
Indicated on display - Press -Q- button to confirm input. Rapi d data transfer Scan Tool sends address word 35
After about 5 seconds, display indicates (for example): Vehicles 1998 : 8L0862257B CL-Pump, DWA, Func D04 Coding 16140 WSC 06812
After about 5 seconds, display indicates (for example): All vehicles: - Press button. Rapi d data transfer HELP Sel ect function XX
Indicated on display Page 7of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-73
Note: A list of available functions is printed out when the HELP button is pressed. On Board Diagnostic (OBD) functions The following functions are possible: 01 - Check Control Module Versions page 01- 85 . 02 - Check DTC Memory page 01-74 . 03 - Output Diagnostic Test Mode page 01- 88 . 05 - Erase DTC Memory page 01-137 . 06 - End Output page 01-139 . 07 - Code Control Module page 01-91 . 08 - Read Measuring Value Block page 01- 99 . Page 8of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-74
Check DTC Memory (scan tool function 02) Note: The DTC display information is updated only when initiating the On Board Diagnostic (OBD) program or when using the "Erase DTC Memory" function 05.
- Switch printer on by pressing PRINT button (indicator lamp in button lights up). Carrying out " Check DTC Memory" function 02 Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -2- to select "Check DTC Memory" function 02. Rapi d data transfer Q 02 - Check DTC Memory
Indicated on display - Press -Q- button to confirm input. X DTC recogni zed
The number of stored DTCs is indicated on display. The stored malfunctions are displayed and printed out in sequence. - Look up printed malfunctions in the DTC table and repair all malfunctions page 01-76 . Page 9of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-75
No DTC recogni zed
If the message "No DTC recognized" is displayed, the program can be returned to the starting point by pressing the button. Rapi d data transfer HELP Sel ect function XX
Indicated on display If something else is displayed: Scan tool operating instructions - Erase DTC Memory (function 05) page 01-137 . - End Output (function 06) page 01-139 . - Disconnect VAG1551 Scan Tool (ST) from Data Link Connector (DLC). Page 10of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-76
Diagnostic Trouble Code (DTC) table, central locking Notes:
The following table lists all the DTCs that can be recognized by the control module for central locking and printed out by the VAG1551 Scan Tool (ST). The DTCs are listed in order according to their 5-digit numbers. DTC 5-digit numbers appear only on the print-out from the scan tool.
Before replacing a component shown as malfunctioning, check wiring and connections to the component as well as the Ground (GND) connections according to the relevant wiring diagram.
When a repair has been completed, check and then erase DTC memory using the VAG1551 Scan Tool (ST). After that, the vehicle should be locked again (with key or remote control) and DTC memory checked again.
DTC memory records all static and sporadic malfunctions. When a malfunction occurs, it is first identified as a static malfunction. If it does not occur again it is registered as a sporadic malfunction, and the letters "/SP" appear at the right of the display.
When the ignition is switched on, all existing malfunctions are automatically re-classified as sporadic malfunctions and will only be registered as static malfunctions if they still occur after testing. Sporadic malfunctions which no longer occur after 50 driving cycles are erased automatically. The three digit malfunction type number appearing next to the DTC is a data code which may be disregarded. Page 11of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-77
DTC VAG 1551 scan tool display Possible cause Corrective action 00955 Key 1 Adaptation limit exceeded Key not matched
Key operated more than 200 times while out of range - Perform remote transmitter coding procedure page 01-105 00956 Key 2 Adaptation limit exceeded Key not matched
Key operated more than 200 times while out of range - Perform remote transmitter coding procedure page 01-105 00957 Key 3 Adaptation limit exceeded Key not matched
Key operated more than 200 times while out of range - Perform remote transmitter coding procedure page 01-105 00958 Key 4 Adaptation limit exceeded Key not matched
Key operated more than 200 times while out of range - Perform remote transmitter coding procedure page 01-105 00991 Interior lighting Page 12of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Short circuit to positive Short circuit to in wiring Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. Page 13of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-78
DTC VAG 1551 scan tool display Possible cause Corrective action 01360 Open ATW Switch Short circuit to Ground Short circuit to Ground in wiring 1)
Door contact switch, driver's-side - F2- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. - Check -F2- and replace if necessary. 01361 Close ATW Switch Short circuit to Ground Short circuit to Ground in wiring 1)
Door contact switch, driver's-side - F2- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. - Check -F2- and replace if necessary. 01362 Close Switch for Tailgate-F124 Short circuit to Ground Short circuit to Ground in wiring 1)
Trunk lock alarm/central locking switch -F124- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations - Repair wiring according to wiring diagram. - Check -F124- and replace if necessary. Page 14of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 1) A malfunction is stored if the Ground is connected for more than 1 min. (e.g. due to an incorrect operation of central locking). Only initiate a repair if there is a proper complaint, otherwise erase DTC memory page 01-137 . Page 15of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-79
DTC VAG 1551 scan tool display Possible cause Corrective action 01363 Switch for CL; Drivers Door-F59 Incorrect Signal
This indication can be caused by the system itself. There is no malfunction of driver's door central locking system switch -F59-. - Ignore DTC and erase DTC memory page 01-137 . 01364 Switch for CL; Passenger Door- F114 Incorrect Signal
This indication can be caused by the system itself. There is no malfunction of passenger door central locking system switch -F114-. - Ignore DTC and erase DTC memory page 01-137 . 01365 Lock/Unlock Switch/Button Int. Short circuit to Ground Short circuit to Ground in wiring 1) Switch for interior lock, driver's side -E150- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. - Check -E150- and replace if necessary. 1) A malfunction is stored if the Ground is connected for more than 1 min. (e.g. due to an incorrect operation of central locking). Only initiate a repair if there is a proper complaint, otherwise erase DTC memory page 01-137 . Page 16of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-80
DTC VAG 1551 scan tool display Possible cause Corrective action 01365 Lock/Unlock Switch/Button Int. Short circuit to B+ Short circuit Short circuit to Ground in wiring
Switch for interior lock, driver's side -E150- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. - Check -E150- and replace if necessary. 01366 Open Via Crash Signal Short circuit to Ground Open/short circuit to B+
Output Diagnostic Test Mode performed at airbag control module -J 234- Airbag control module -J 234- was triggered
Short circuit in wiring between airbag control module and central locking control module Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Erase DTC memory page 01-137 . - Repair wiring according to wiring diagram. 01367 Switch on Via CL Pump Too little pressure in pneumatic lines Central locking pump faulty - Check pneumatic lines for leaks. - Exchange central locking pump. - Check all actuators of central locking system and replace if necessary. Page 17of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-81
DTC VAG 1551 scan tool display Possible cause Corrective action 01368 Alarm Via Luggage Compartment Switch
Anti-theft system triggered by unauthorized opening of rear lid Trunk lid alarm switch -F123- faulty - Erase DTC memory. - Replace -F123-. 01369 Alarm Via Front Hood Switch
Anti-theft system triggered by unauthorized opening of hood Hood alarm switch -F120- faulty - Erase DTC memory. - Replace -F120-. 01370 Alarm Via Interior Scanning Short circuit to Ground
Anti-theft system triggered by control module for ultra-sound sensors -J 347-
Control module for ultra-sound sensors -J 347- faulty
Short circuit in wiring between control module for ultra-sound sensors and central locking control module Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Erase DTC memory. - On Board Diagnostic (OBD) ultra-sound interior monitoring page 01-108 . - Repair wiring according to wiring diagram. 01371 Alarm Via Door Contact Page 18of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Switch Driv. Side
Anti-theft system triggered by unauthorized opening of driver-side door Door contact switch, driver's side -F2- faulty - Erase DTC memory. - Replace door contact switch -F2-. Page 19of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-82
DTC VAG 1551 scan tool display Possible cause Corrective action 01372 Alarm Via Door Ctact. Switch Rear PS
Anti-theft system triggered by unauthorized opening of passenger-side and/or rear door(s) Door contact switches -F3-, -F10-, -F11- faulty - Erase DTC memory. - Replace contact switch -F3-, -F10-, -F11-. 01373 Alarm Via Radio Ground Teminal
Anti-theft system triggered by unauthorized removal of radio
Ground connection for anti-theft system has an open circuit - Erase DTC memory. - Provide Ground connection. 01374 Alarm Via Terminal 15
Anti-theft system triggered by unauthorized starting (short circuiting) Short circuit between terminal 30 and 15 Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Erase DTC memory. - Repair wiring according to wiring diagram. Page 20of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-83
DTC VAG 1551 scan tool display Possible cause Corrective action 01384 Alarm via Broken Glass Sensor (rear window)
Anti-theft alarm triggered by attempted break-in at rear window Open in rear window defroster circuit False alarm Electrical Wiring Diagrams, Troubleshooting & Component Locations binder Repair Manual, Body Exterior, Repair Group 64 - Erase DTC memory - Check and repair wiring and connectors per wiring diagram. - Replace rear window 01389 Tailgate Open Switch- F124 Short circuit to Ground Short circuit to Ground in wiring
Trunk lock alarm/central locking switch - F124- faulty Electrical Wiring Diagrams, Troubleshooting & Component Locations binder - Repair wiring according to wiring diagram. - Replace -F124- in trunk lock. Page 21of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-84
DTC VAG 1551 scan tool display Possible cause Corrective action 01403 Broken Glass Sensors
Broken glass sensor for rear left side window -G183 or Broken glass sensor for rear right side window -G184 Anti-theft alarm triggered by attempted break-in at one of the side windows Open in circuit of one of the side windows False alarm Electrical Wiring Diagrams, Troubleshooting & Component Locations binder Repair Manual, Body Exterior, Repair Group 64 - Erase DTC memory - Check and repair wiring and connectors per wiring diagram. - Replace side window as necessary 65535 Control Module Malfunctioning - Replace control module. Page 22of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-85
Check Control Module Versions (scan tool function 01) Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -1- to select "Check Control Module Versions" function 01. Rapi d data transfer Q 01 - Check Control Module Versions
Indicated on display Explanation of display 8L0862257B: Part No. of central locking control modules Central locking pump, Anti-theft system: component identification D04: software version Coding 12172: coding page 01-91 WSC 06812: dealership number - Press button Page 23of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-86
Indicated on display Explanation of display 8L0862257B: Part No. of central locking control modules Central locking pump, Anti-theft system: component identification D04: software version Coding 16140: coding page 01-91 WSC 06812: dealership number - Press button Page 24of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-87
All vehicles: If one of these messages is indicated on the display, perform On Board Diagnostic (OBD) according to OBD instructions: Rapi d data transfer HELP Control module does not answer
Indicated on display or Rapi d data transfer HELP Error in communi cation link
Indicated on display or Rapi d data transfer HELP K wire not switching to Ground
Indicated on display or Rapi d data transfer HELP K wire not switching to B+
Indicated on display Electrical Wiring Diagrams, Troubleshooting & Component Locations binder Note: If nothing appears on display: Scan tool operating instructions - Check wiring connections for Data Link Connector (DLC). Rapi d data transfer HELP
Indicated on display Page 25of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Sel ect function XX Page 26of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-88
Output Diagnostic Test Mode (scan tool function 03) Notes:
The Output Diagnostic Test Mode may only be performed with the vehicle stationary and the engine not running.
Any malfunctions identified by the Output Diagnostic Test Mode must be checked and repaired. The output DTM activates the following elements in sequence:
Emergency flashers and anti-theft horn (only for vehicles equipped with anti-theft system)
Interior monitoring (activated even if interior monitoring is not installed)
Emergency flashers and interior lights as a test of the crash signal Page 27of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-89
Carrying out " Output Diagnostic Test Mode" function 03 Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -3- to select "Output Diagnostic Test Mode" function 03. Rapi d data transfer Q 03 - Output Diagnostic Test Mode
Indicated on display - Press -Q- button to confirm input. Output Diagnostic Test Mode Create active alarm
Indicated on display (emergency flasher and anti-theft horn are activated) - Press button. Output Diagnostic Test Mode Next final ctrl : operate
Indicated on display - Press button. Output Diagnostic Test Mode Activate interior monitoring
Indicated on display (central locking control module sends a signal which activates interior monitoring system) Notes: After activating interior monitoring, a system dependant waiting time of 30 seconds must be maintained. If one alarm is activated, an entry into DTC memory of the control module for central locking will be made "1370; alarm via interior monitoring" as well as into control module for ultra-sound sensors "alarm via sensor for anti-theft warning system; fl, fr, rl, rr". Page 28of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Malfunctions must be checked and erased in DTC memory of the respective control module. Page 29of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-90
- Press button. Output Diagnostic Test Mode Next final ctrl : operate
Indicated on display - Press button. Output Diagnostic Test Mode Si mulate crash si gnal
Indicated on display (emergency flashers and interior lights are triggered) Notes: - Press button. The malfunction "1366; opening via crash-signal" is stored in DTC memory of the control module for central locking. Output Diagnostic Test Mode (DTM) must be repeated with airbag control module. After performing output Diagnostic Test Mode (DTM) of airbag control module, DTC "01366 opening via crash signal" will also be stored in control module for central locking. The malfunction must be checked in DTC memory of the control module for central locking page 01-74 and erased page 01-137 . Output Diagnostic Test Mode END
Indicated on display The program is now back at its starting point. - Press button. Rapi d data transfer HELP Sel ect function XX
Indicated on display Page 30of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-91
Code Control Module (scan tool function 07) With coding, different central locking variations can be enabled for possible function/equipment variations. Central locking variations:
Central locking with anti-theft system
Central locking with remote control and anti- theft system Notes:
The basic functions of the central locking system are listed in a standard code table page 01-93 .
Further coding variations are possible at the request of the customer page 01-94 . Carrying out " Code Control Module" function 07 Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -7- to select "Code Control Module" function 07. Page 31of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Rapi d data transfer Q 07 - Code Control Modul e
Indicated on display - Press -Q- button to confirm input. Code Control Module Enter code number XXXXX (0-32000)
Indicated on display Page 32of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-92
- Input coding of the central locking control module with keypad (e.g. 16140 for central locking with anti-theft/remote) vehicles1998 . Code Control Module Q Enter code number 16140 (0-32000)
Indicated on display - Press -Q- button to confirm input. 8L0862257N CL pump, DWA, Func D12 Coding 16140 WSC 06812
Note: Explanation of display page 01-85 . - Indicated on display (control module identification with current coding) - Press button Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -6- to select "End Output" function 06. Rapi d data transfer Q 06 - End Output
Indicated on display - Press -Q- button to confirm input. Rapi d data transfer HELP Insert address word XX
Indicated on display Page 33of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-93
Standard code table Vehicles 1997 (with Delta radio): Vehicle type Central locking variation Standard coding Audi A4 Vehicle with central locking and anti-theft system 03468
Vehicle with central locking, anti-theft system and keyless entry 12172 Vehicles 1998 (with Concert radio): Vehicle type Central locking variation Standard coding Audi A4 Vehicle with central locking and anti-theft system 03340
Vehicle with central locking, anti-theft system and keyless entry 16140 Page 34of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-94
All vehicles: In addition to basic coding, it is possible to offer customers the following option:
Vehicle automatically locks upon reaching a speed of about 15 km/h (10 mph) and unlocks when the key is removed from the ignition Optional code table Vehicles 1997 (with Delta radio): Vehicle type Central locking variation Optional coding Audi A4 Vehicle with central locking and anti-theft system 03500
Vehicle with central locking, anti-theft system and keyless entry 12204 Vehicles 1998 (with Concert radio): Vehicle type Central locking variation Optional coding Audi A4 Vehicle with central locking and anti-theft system 03372
Vehicle with central locking, anti-theft system and keyless entry 16172 Page 35of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-95
Notes: Safety central locking (SCL) has the following functions (when vehicle is unlocked):
If central locking is activated only once (with key or keyless entry), the driver-side door and the fuel filler flap are unlocked, while all other doors and the rear lid remain locked.
If central locking is immediately activated a second time, the remaining doors and the rear lid are unlocked. Page 36of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-96
Standard coding table for vehicles (tailgate with soft-touch) 1999 : Vehicle type Central locking version Standard coding Audi A4 Vehicles with central locking 00001
Vehicles with central locking and anti-theft warning system 00267
Vehicles with central locking and radio-frequency remote control 12865
Vehicles with central locking, anti-theft warning system and radio-frequency remote control 13131 Note: Coding for vehicles which have tailgates equipped with soft-touch, incorporates: During mechanical unlocking (via tailgate lock), the tailgate unlocks and opens. In this way, the tailgate can be opened without operating soft-touch. Page 37of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-97
Standard coding table for vehicles 18.00 : Vehicle type Central locking version Standard coding Audi A4 Vehicles with central locking 02049
Vehicles with central locking and anti-theft warning system 02315
Vehicles with central locking and radio-frequency remote control 14913
Vehicles with central locking, anti-theft warning system and radio-frequency remote control 15179 Notes: Coding for vehicles from cw 18.00 incorporates:
Changed door or window regulator logic. As soon as the door is opened with "terminal. 15 off" the window regulators can no longer be operated.
During mechanical unlocking (via tailgate lock), the tailgate unlocks and opens. In this way, the tailgate can be opened without operating soft-touch. Page 38of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-98
All vehicles: Beside the basic coding, it is possible to offer the customer the following additional functions: To activate the following additional functions, the following number value must be added to the respective basic coding.
Safety central locking (SCL) +4 Automatic locking of the vehicle at a speed of approx. 15 km/h +32 (with SCL +36) The value 4 for SCL and 32 for automatic locking above a speed must be added to the current coding. e.g. CL-pump with ATS/remote and SCL (15179 +4 =15183). Notes:
Safety central locking (SCL) has the following function (vehicle locked):
If the CL is only operated once (via key or remote control), the drivers door and the tank flap will be unlocked while all other doors and Page 39of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 tailgate remain locked.
If the CL is immediately operated for a second time, the remaining doors and tailgate will also be unlocked. Page 40of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-99
Read Measuring Value Block (scan tool function 08) Note: The current system condition can be determined by using "Read Measuring Value Block" function 08. Carrying out " Read Measuring Value Block" function 08 Rapi d data transfer HELP Sel ect function XX
Indicated on display - Press buttons -0- and -8- to select "Read Measuring Value Block" function 08. Rapi d data transfer Q 08 - Read Measuri ng Value Block
Indicated on display - Press -Q- button to confirm input. Read Measuring Value Bl ock Input di splay group number XXX
Indicated on display The selected measuring value block is now indicated in standard format. - Press buttons -0-, -0- and -1- to input display group number 1 (001). - Press -Q- button to confirm input. Page 41of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-100
Read Measuring Value Block, overview Display group 001
Read Measuring Value Block 1 Indicated on display
0100 100 0000 0000 X X X
X Rear lid: 1 =opened, 0 =closed Luggage compartment light:1 =light on, 0 =light off Switch for unlocking rear lid (A8 only): 1 =activated, 0 =not activated Motor for unlocking rear lid (A8 only): 1 =motor running, 0 =motor not running
XX
XX Actuator switch or internal switch at passenger-side door: 00 =not activated, 01 =lock, 10 =unlock, 11 =not permissible Actuator switch or internal switch at driver-side door: 00 =not activated, 01 =lock, 10 =unlock, 11 =not permissible
X X X
Passenger-side door and rear doors: 1 =open, 0 =closed (USA: only rear doors)
Position of key in lock cylinder Page 42of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 X X X X
Opening driver-side and passenger-side doors: 1 =key activated, 0 =key in middle position
Closing driver-side and passenger-side doors: 1 =key activated, 0 =key in middle position
Opening rear lid: 1 =key activated, 0 =key in middle position
Closing rear lid: 1 =key activated, 0 =key in middle position
Page 43of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-101
Display group 002
Read Measuring Value Block 2 Indicated on display
0100 1000 111
X X X Terminal 15: 1 =Ignition on, 0 =Ignition off S-contact: 1 =S-contact on, 0 =S-contact off Ground signal from radio: 0 =Radio installed, 1 =Radio removed
Page 45of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3
1) When you activate keyless entry, the relevant keyless entry key memory position blinks.
2) This measuring value block also shows non-coded keyless entry keys (e.g. for function control of keyless entry).
Page 46of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-103
Display group 004 (vehicles up to software version D04)
Read Measuring Value Block 4 Indicated on display
100 1011 1100 1100 X X X X Anti-theft system activated: 0 =no, 1 =yes Safety central locking: 0 =no, 1 =yes Disregard measuring value: coding always 0
X X X X Anti-theft system activated: 0 =no, 1 =yes Interior monitoring system is OBD capable: 0 =yes, 1 =no Locking vehicle above a speed: 0 =yes, 1 =no Vehicle is a convertible: 0 =no, 1 =yes
X X X X
USA-Door logic 1) activated: 0 =no, 1 =yes
Confirmation of anti-theft system via emergency flashers: 0 =no, 1 =yes
Confirmation of anti-theft system via horn: 0 =no, 1 =yes
Confirmation of keyless entry via emergency flashers: 0 =no, 1 =yes
X Remote transmitter activated: 0 =no, 1 =yes
Page 47of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 X X Activation of security central locking also possible with remote transmitter: 0 =no, 1 =yes Comfort closing also possible with remote transmitter: 0 =no, 1 =yes
1) Window regulators will not work if ignition is off and driver-side door is open.
Page 48of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-104
Display group 004 (vehicles from software version D05)
Read measuring value block 4 Indicated on display
100 1111 1000 1100 X X X
X Anti-theft warning system activated: 0 =No, 1 =Yes Safety-CL activated: 0 =No, 1 =Yes Confirmation of anti-theft warning system via emergency flashers:0 =No, 1 =Yes Tailgate opening, lock cylinder rear: 0 =No, 1 =Yes
X X X X Anti-theft warning system activated: 0 =No, 1 =Yes Interior monitoring is OBD cabable: 0 =Yes, 1 =No Locking vehicle above a speed: 0 =No, 1 =Yes Vehicle is a Cabrio: 0 =No, 1 =Yes
X X
X
USA-door logic 1) activated: 0 =No, 1 =Yes
Confirmation of radio-frequency remote control button "open" via emergency flashers: 0 =No, 1 =Yes
Confirmation of anti-theft warning system via ATS horn: 0 =No, 1 =Yes Confirmation of radio-frequency remote control button "lock" via emergency flashers:
Page 49of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 X
0 =No, 1 =Yes X X X Radio-frequency remote control activated: 0 =No, 1 =Yes For safety central locking selection, CL-function for operation via radio frequency remote, otherwise SCL- function: 0 =No, 1 =Yes Comfort locking/ -unlocking also possible via radio-frequency remote control: 0 =No, 1 =Yes
1) All window regulators are not functional, if the ignition is switched off and the drivers door is open at the same time.
Page 50of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-105
Remote transmitter, coding Two remote transmitters are supplied with the vehicle. If further transmitters are required, they must be coded to interact properly with the central locking control module. This procedure must be performed after changing the batteries in keys with remote control function, or if the scan tool displays DTCs of 00955 to 00958 Remote transmitter coding procedure
- Switch ignition on (using separate key).
- Check how many transmitters have already been coded in measuring value block 003 Read Measuring Value Block page 01-99 . Read Measuring Value Block 3 0 0001 0 0000
Indicated on display Display field 2 indicates how many remote transmitters have been coded and in which memory positions (in the example given, 1 transmitter in position 1). - Lock vehicle from outside using key to be coded via driver-side door lock. - Press "unlock" button within 5 seconds often enough to reach next memory position (in example given, twice). Page 51of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 Every press of the button is confirmed by the emergency flashers and the anti-theft system horn. - Wait 5 seconds. Page 52of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-106
- Now press "unlock" button one more time (vehicle unlocks).
- Switch ignition off and remove ignition key.
- Check function of new transmitter.
- Check display field 2 in measuring value block 003. It should now display another "1" (in example given: 1100). Note: Be sure that new transmitters are always coded into free memory positions. If occupied positions (distinguishable by a "1") are used, the transmitter previously coded to this position will no longer work. Existing remote transmitter recoding procedure This procedure must be performed after changing the batteries in keys with remote control function, or if the scan tool displays DTCs of 00955 to 00958
- Press any button on transmitter. If vehicle does not respond by locking or Page 53of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 unlocking:
- Lock and unlock vehicle within 30 seconds using driver-side lock.
- Now check function of recoded remote transmitter. Clearing memory positions Note: It is possible to clear all memory positions, e.g. if a customer loses a remote transmitter. Proceed as follows: Page 54of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3 01-107
- Switch ignition on using key.
- Then mechanically lock central locking from outside vehicle using key.
- Activate remote transmitter "unlock" button on key five times at one second intervals. A short horn signal will sound each time.
- Then, after 6 seconds, press remote transmitter "unlock" button to confirm this clearing procedure one more time.
Central locking should no longer unlock itself via remote transmitter.
- Switch ignition off. Up to four transmitters can now be coded again. Page 55of 55 Central locking On Board Diagnostic (OBD) 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD04.01.3