Professional Documents
Culture Documents
Sarmica 2
Sarmica 2
Although the terms CPL and HPL are in widespread use and the products have been applied for many years, questions are still
frequently asked concerning the differences in quality and the product possibilities offered by the two alternatives. But in the context
of laminates, there are also other frequently used terms and/or material descriptions, which are listed below.
1.
2.
2.3 OVERLAY
Overlay is bleached, transparent paper, capable of absorbing a large quantity of resin. It is used to protect the print impression on
printed decor papers and to improve the abrasion resistance.
2.4 UNDERLAY
Underlay, or barrier paper, is a layer of paper between decor paper and sodium Kraft paper, intended to prevent a chemical reaction
from taking place between the resins. It can also be used to achieve optical effects.
2.5 RESINS
Melamine-formaldehyde resins produce transparent and hard coatings and are therefore ideally suited for the surface layers of
decorative laminate sheets. Brown, relatively elastic phenol formaldehyde resins are used in the impregnation of core layers.
1/3
3.
Laminate Description
Decorative sheet laminate consists of layers of cellulose fibrous material (paper), impregnated with thermosetting resins. These are bonded
together using the manufacturing methods described below. The surface layer generally consists of a melamine resin impregnated overlay,
decor paper and a barrier paper, if applicable. The core of a laminate consists of phenol resin impregnated sodium Kraft papers. The application
of heat and pressure provides flowing and subsequent curing of the resins. Through cross-linked bonding of the resins, reinforced by the
cellulose fibres of the papers, a very homogenous material with a non-porous surface is produced.
4.
Laminate Composition
The laminate composition provides information on the number of paper layers and their construction, i.e. the laminate thickness as well
as the quality requirements are determined. Apart from the dcor paper, the number and weights of the core papers and the use of
overlay and underlay are also defined.
5.
Manufacturing Process
5.1 CPL-PROCESS
The term CPL already provides a hint with regard to the manufacturing process; CPL is produced in continuously operating
double-belt presses with a press pressure of between 25 and 50 bar and temperatures ranging from 150 C to 170 C. Depending
on the laminate thickness and the length of the pressing zone, the feed rate varies from 8 to 30 m/min.
5.2 HPL-PROCESS
HPL is produced in discontinuously operating multi daylight presses with press pressures of between 70 and 80 bar and temperatures
in excess of 120 C. In the context of the laminate production process, the pressure unit is very often also expressed in megapascal
[MPa]. For example, 50 bar is equivalent to 5 megapascal. Daylight presses can have up to 45 daylights, and each level can
accommodate up to 24 laminate sheets (ranging in thickness from approx. 0.50 to 1.90 mm). Depending on the press feed and the
maximum temperature, the entire press cycle, including re-cooling, lasts approximately 100 minutes.
6.
Both qualities, CPL and HPL, are classified and tested in accordance with EN 438:2005. The laminate composition and resins used
are comparable for both types of laminate. Effectively therefore, identical specifications in terms of laminate thickness, dcor and
surface, achieve the same test results.
The laminate characteristics are defined in EN 438:2005 and three important requirements in terms of laminate properties are achieved
by the following main criteria:
Abrasion resistance is influenced by the selection of a suitable
overlay. Impact resistance is influenced by the laminate thickness.
Scratch resistance is influenced by surface structure
2/3
EN_06/09
sted for abrasion resistance, impact resistance and scratch resistance correspond to the values required by the Standard
for kitchen worktops.
T
h
e
t
a
b
l
e
b
e
l
o
w
p
r
o
v
i
d
e
s
a
n
e
x
c
e
r
p
t
o
f
e
s
s
e
n
ti
a
l
l
a
m
i
n
a
t
e
p
r
o
p
e
rt
i
e
s
.
T
h
e
v
a
l
u
e
s
li
Target value
EN 438-1
Property
Unit
CPL
HPL
Min. thickness
mm
0,15
0,50
Max. thickness
mm
1,50
40,0
150
500
High gloss
Limited
yes
Compact laminate *
no
yes
Abrasion resistance
10
Revolutions IP
Revol. wear value
150
350
150
350
150
350
Impact resistance
20
N (min.)
20
20
20
Scratch resistance
25
Rating
Light fastness
27
4 to 5
4 to 5
4 to 5
16
Rating
30
Rating
14
Rating
3 to 5
3 to 5
Resistance to staining
26
Rating
Group 1 + 2
Group 3
5
3
5
3
5
3
7.
The information contained within this data sheet is based on practical experience as well as in-house tests and reflects our current state of knowledge. It is intended for
information only and does not constitute a guarantee in terms of product properties or their suitability for specific applications. Unless otherwise stated, our General Terms
and Conditions apply.
3/3