Professional Documents
Culture Documents
Esterification
Esterification
Chemical Equilibrium
Objective
Many chemical reactions, especially those of organic substances, do not go to completion.
Rather, they come to a point of chemical equilibrium before the reactants are fully
converted to products. At the point of equilibrium, the concentrations of all reactants
remain constant with time. The position of this equilibrium is described by a function
called the equilibrium constant, Keq, which is a ratio of the amount of product present to
the amount of reactant remaining once the dynamic equilibrium has been reached. In this
experiment, you will determine the equilibrium constant for an esterification reaction.
Introduction
Early in the study of chemical reactions, it was noted that many chemical reactions do not
produce as much product as might be expected, based on the amounts of reactants taken
originally. These reactions appeared to have stopped before the reaction was complete.
Closer examination of these systems (after the reaction had seemed to stop) indicated
that there were still significant amounts of all the original reactants present. Quite
naturally, chemists wondered why the reaction had seemed to stop, when all the necessary
ingredients for further reaction were still present.
Some reactions appear to stop because the products produced (by the original reaction)
themselves begin to react, in the reverse direction to the original process. As the
concentration of products begins to build up, product molecules will react more and more
frequently. Eventually, as the speed of the forward reaction decreases while the speed of
the reverse reaction increases, the forward and reverse processes will be going on at
exactly the same rate. Once the forward and reverse rates of reaction are identical,
there can be no further net change in the concentrations of any of the species in the
system. At this point, a dynamic state of equilibrium has been reached. The original
reaction is still taking place but is opposed by the reverse reaction.
The point of chemical equilibrium for a reaction is most commonly described numerically by
the equilibrium constant, Keq. The equilibrium constant represents a ratio of the
concentrations of all product substances present at the point of equilibrium to the
concentrations of all original reactant substances (all concentrations are raised to the
power indicated by the coefficient of each substance in the balanced chemical equation
for the reaction). For example, for the general reaction
aA + bB cC + dD
the equilibrium constant would have the form
Keq =
[C ]c [ D]d
[ A]a [ B]b
A ratio is used to describe the point of equilibrium for a particular chemical reaction
scheme because such a ratio will be independent of specific amounts of substance that
might have been used initially in a particular experiment. The equilibrium constant K eq is a
constant for a given reaction at a given temperature.
Introduction
In Part I of this experiment you will determine the equilibrium constant for the
esterification reaction between n-propyl alcohol and acetic acid.
You will set up the reaction in such a way that the initial concentrations of n-propyl alcohol
and acetic acid will be determined. The initial molarity (M) of acid present in the system
will be determined by titration with sodium hydroxide solution.
Esterification reactions are extremely slow, but can be catalyzed by the addition of a
strong mineral acid. In this experiment, a small amount of sulfuric acid will be added as a
catalyst to increase the rate of the reaction. The amount of catalyst added will have to
be determined by titration with sodium hydroxide. This catalyst will be present in the
reaction chamber even after equilibrium is achieved and therefore changes the total acid
content of the equilibrium mixture.
The reaction will then be allowed to stand for a minimum of one week to allow it to come to
equilibrium. As acetic acid reacts with n-propyl alcohol, the acidity of the mixture will
decrease, reaching a minimum once the system reaches equilibrium. Then the molarity (M)
of the acid remaining at equilibrium will be determined by titration one again .
By analysis of the amounts of each reagent used during week one, and by determining the
amount of acetic acid (HAc) that will be present after the system has reached equilibrium,
one will be able to calculate the concentration of all species present in the equilibrium
mixture. From this, the value of the equilibrium constant can be determined.
The concentration of acetic acid in the mixture is determined by the technique of
titration. Acetic acid reacts with sodium hydroxide (NaOH) on a 1:1 stoichiometric basis
HC2H3O2
NaOH
NaC2H3O2 +
H2O
A precise volume of the reaction mixture is removed with a pipet and a standard NaOH
solution is added slowly from a buret until the acetic acid has been completely neutralized
(this is signaled by an indicator, which changes color). From the volume and concentration
of the NaOH used and the volume of reaction mixture taken, the concentration of acetic
acid in the reaction mixture may be calculated.
Apparatus/Reagents Required
50-mL buret, 750 mL standard 0.10 M NaOH solution, phenolphthalein indicator solution, 1
mL pipet and rubber safety bulb, n-propyl alcohol (1-propanol), glacial acetic acid, 6 M
sulfuric acid, erylermeyer flasks (250 mL and 125 mL), rubber stopper (plastic wrap), and
other beakers and funnels as needed.
Procedure
A. First Week: Setup of the Initial Reaction Mixture
1. Clean a buret with soap and water until water does not bead up on the inside of
the buret. Rinse the buret and pipet with tap water several times to remove all
soap. Follow by rinsing with small portions of distilled water.
2. Obtain the sigma bottle with standard 0.10 M NaOH solution. Rinse the buret
several times with small portions of NaOH solution (discard the rinsings), then
fill the buret with NaOH solution. Keep the remainder of the NaOH solution
sealed for later use.
3. Clean two 250-mL titration flasks and label them as 1 and 2. Rinse the flasks
with tap water, followed with small portions of distilled water. Place
approximately 25 mL of distilled water in each flask and set aside until needed.
4. Since glacial acetic acid and n-propyl alcohol are both liquids, it is more
convenient to measure them out by volume than by mass.
5. Obtain a clean and dry a 125-mL Erlenmeyer flask from the oven. Label the
flask as reaction mixture. Cover a rubber stopper that securely fits the flask
with plastic wrap (this prevents the stopper from being attacked by the vapors
of the reaction mixture).
6. Obtain a clean and dry graduated cylinder, rinse it with the glacial acetic acid.
Then use the cylinder to measure 14 +/- 0.2 mL of glacial acetic acid (0.25 mol)
and transfer the acetic acid to the 125-mL reaction mixture Erlenmeyer flask.
7. Obtain another clean and dry graduated cylinder, rinse it with n-propyl alcohol.
Then use the cylinder to measure 19 +/- 0.2 mL of n-propyl alcohol (0.25 mol)
and add to the acetic acid in the 125-mL reaction mixture Erlenmeyer flask.
Stopper the flask and swirl the flask for several minutes to mix the reagents.
8. Obtain a clean dry 1-mL volumetric transfer pipet, use the pipet to transfer
exactly 1.00 mL of the reaction mixture to each of the two 250-mL Erlenmeyer
flasks (1 and 2). Restopper the flask containing the n-propyl alcohol/acetic acid
reaction mixture to prevent evaporation.
9. Add 3-4 drops of phenolphthalein indicator to each of the two samples to be
titrated.
10. Record the initial level of the NaOH solution in the buret. Place Erlenmeyer
flask #1 under the tip of the buret, and slowly begin adding NaOH solution to
the sample. Swirl the flask during the addition of NaOH. As NaOH is added,
red streaks will begin to appear in the sample due to the phenolphthalein, but
the red streaks will disappear as the flask is swirled. The endpoint of the
titration is when a single additional drop of NaOH causes a faint, permanent
pink color to appear. Record the level of NaOH in the buret.
11. Repeat the titration using Erlenmeyer flask #2, recording initial and final levels
of NaOH.
12. Discard the samples in flasks #1 and #2.
Calculation:
From the average volume of NaOH used to titrate 1.00 mL of the reaction and the
concentration of the NaOH, calculate the concentration (in mol/L) of acetic acid in the
reaction mixture.
moles of NaOH used = (concentration of NaOH, M) x (volume used to titrate, L)
moles of HAc = moles of NaOH at the color change of the indicator
molarity of HAc =
______________moles of Ac_____________
liters of reaction mixture taken with pipet (1.00mL)
Since the reaction was begun using equal molar amounts of acetic acid and n-propyl alcohol
(i.e., 0.25 mol of each), the concentration of acetic acid calculated also represents the
concentration of n-propyl alcohol in the original mixture.
acetic acid in the system once equilibrium has been reached. Next week, you will again
titrate 1.00 mL samples of the reaction mixture with NaOH, to determine what
concentration of acetic acid remains in the mixture at equilibrium. However, since NaOH
reacts with both the acetic acid of the reaction and also with the mineral acid catalyst
(H2SO4), some method must be found to determine the concentration of the mineral acid in
the reaction mixture. Sulfuric acid will be used as the catalyst.
13. Refill the buret (if needed) with standard NaOH and record the initial level.
Clean out Erlenmeyer flasks #1 and #2, rinse, and fill with approximately 25 mL
of distilled water. Have ready the 1-mL pipet and rubber safety bulb.
14. Add, with swirling, 10 drops of 6 M sulfuric acid catalyst to the acetic
acid/propyl alcohol reaction mixture. Immediately pipet a 1.00-mL sample of
the catalyzed reaction mixture into both flasks. Do not delay pipeting, or the
concentration of acetic acid will begin to change as the reaction occurs.
15. Recording initial and final NaOH levels in the buret, titrate the catalyzed
reaction mixture in flasks #1 and #2, using 3-4 drops of phenolphthalein
indicator to signal the endpoint.
16. Since the samples of catalyzed reaction mixture contain the same quantity of
acetic acid as the samples of uncatalyzed mixture, the increase in volume of
NaOH required to titrate the second set of 1-mL samples represents a measure
of the amount of sulfuric acid present.
17. Stopper the 125-mL flask containing the acetic acid/n-propyl alcohol mixture.
Place the reaction mixture in your lab drawer or in a safer place until next week.
Calculation:
By subtracting the average volume of standard NaOH used in Part A (acetic acid only)
from the average volume of NaOH used in Part B (acetic acid + sulfuric acid), calculate how
many mL of the standard NaOH solution are required to titrate the sulfuric acid catalyst
present in 1 mL of the reaction mixture.
This volume represents a correction that can be applied to the volume of NaOH that will
be required to titrate the samples next week, after the equilibrium has been reached.
Calculate the change in the concentration of acetic acid between the initial and the
equilibrium mixture. From the change in the concentration of acetic acid, calculate the
concentrations of the two products of the reaction (the ester and water) present in the
equilibrium mixture.
From the concentrations of each of the four components of the system at equilibrium,
calculate the equilibrium constant (Keq) for the reaction.
Calculation:
1.
Concentration of the standard NaOH solution
2.
Volume of NaOH to titrate 1 mL initial uncatalyzed mixture (1 st week)
flask # 1 & 2. Report Mean (average) volume used to titrate.
3.
Concentration of acetic acid, M, in original mixture (consider moles and volume).
4.
Volume of NaOH to titrate catalyzed reaction mixture (1 st week) flask 1 & 2.
Report Mean (average) volume used to titrate with catalyst present.
5.
Determine the volume of NaOH required to neutralize the sulfuric acid
(catalyst), this is a correction factor.
6.
Volume of NaOH to titrate 1 mL of equilibrium mixture (2nd week) flask 1 & 2.
Report Mean (average) volume used to titrate equilibrium mixture.
7.
Apply the correction volume for NaOH used to neutralize the catalyst H 2(SO4).
8.
Concentration of acetic acid, M, in equilibrium mixture. (also concentration of npropyl alcohol).
9.
Use an I (initial), C (change), E (equilibrium) diagram to show the initial
concentration, change in concentration, and final concentration of all
components in the chemical equation.
10.
Calculate the Keq for this reaction.
Finish the laboratory report by including the following:
Results Table:
Conclusion Statement:
Discussion Theory: Be sure to discuss: equilibrium, catalyst, titration, pH, indicator,
and explain esterification reactions (specifically write the molecular structure of all
of the reactants and products for this esterification reaction).
Sources of Error (2):