Professional Documents
Culture Documents
Rain Water Harvesting Project
Rain Water Harvesting Project
Rainwater harvesting is the process of collecting, filtering and storing water from roof
tops, paved and unpaved areas for multiple uses. The harvested water can also be used
for potable purposes after testing and treatment. The surplus water after usage can be
used for recharging ground water aquifer through artificial recharge techniques. This can
also result in improving the quality of the ground water e.g. lower fluoride content in
ground water. Rainwater harvesting mechanisms are designed after assessing the site
conditions such as incident rainfall, subsurface strata and their storage characteristics,
infiltration test and by building suitable structures to collect and store rainwater.
Rainwater harvesting system provides a source of soft, high quality water, reduce
dependence on wells and other sources, and, in many contexts, are cost effective.
Rainwater harvesting system can range in size from a simple PVC tank to a contractor
designed and built sump - costing thousand of rupees. Rainwater system are inherently
simple in form. Harvesting rainwater is not only water conserving, it is also energy saving
since the energy input required to operate a centralized water system can be bypassed.
A range of filters for different filtration rates have also been designed using different filter
media.
Benefit
Catchment area
Conveyance system
Filter unit
Storage
Delivery system
Usage
Recharge
Harvesting
System
From
where
to
harvest
rain
Whether
to
store
rainwater
or
use
it
for
recharge:
The decision whether to store or recharge water depends on the rainfall pattern and the potential to do
so, in a particular region. The sub-surface geology also plays an important role in making this decision.
early as the third millennium BC, farming communities in Baluchistan and Kutch
impounded rain water and used it for irrigation dams.
ARTIFICAL RECHARGE TO GROUND WATER :
Artificial recharge to ground water is a process by which the ground water reservoir is
augmented at a rate exceeding that obtaining under natural conditions or
replenishment. Any man-made scheme or facility that adds water to an aquifer may
be considered to be an artificial recharge system.
WHY RAIN WATER HARVESTING :
Rain water harvesting is essential because :Surface water is inadequate to meet our demand and we have to depend on ground
water.
Due to rapid urbanization, infiltration of rain water into the sub-soil has decreased
drastically and recharging of ground water has diminished.
As you read this guide, seriously consider conserving water by harvesting and
managing this natural resource by artificially recharging the system. The examples
covering several dozen installations successfully operating in India constructed and
maintained by CGWB, provide an excellent snapshot of current systems.
RAIN WATER HARVESTING TECHNIQUES :
There are two main techniques of rain water harvestings.
Storage of rainwater on surface for future use.
Recharge to ground water.
The storage of rain water on surface is a traditional techniques and structures used
were underground tanks, ponds, check dams, weirs etc. Recharge to ground water is
a new concept of rain water harvesting and the structures generally used are :Pits :- Recharge pits are constructed for recharging the shallow
aquifer. These are constructed 1 to 2 m, wide and to 3 m. deep which
are back filled with boulders, gravels, coarse sand.
Trenches:- These are constructed when the permeable stram is
available at shallow depth. Trench may be 0.5 to 1 m. wide, 1 to
Individual
Houses
Multistoried
building
55 cu. m
275 cu. m.
100 days
500 days
Rainwater Harvesting
The capture and storage of rainwater for subsequent utilization is called rainwater
harvesting. Rainwater harvesting is often one component of a water management
strategy in which a various water sources satisfy a spectrum of demands.
Rainwater is directly harvested for domestic (household) consumption in more than
one hundred countries, both in arid regions where water is scarce, and in humid
regions where precipitation is easily captured. Rainwater harvesting systems reflect
the diversity of Earth's many societies, climates, and regions. Systems can be
designed quite differently, use a variety of materials, satisfy an array of performance
requirements, and have different cultural impacts.
Archaeological excavations document ancient rainwater harvesting in
Mesoamerica , the Mediterranean, and the Orient. Today, rainwater is harvested by
both traditional technologies and optimally engineered facilities. Traditional rainwater
harvesting systems include a rooftop and adjacent cistern. Improved systems include
paved hillsides, airport runways, subterranean reservoirs, disinfection, and
automated monitoring. Computercontrolled systems are used in parts of Japan and
Scandinavia.
Catchments.
A rooftop is the most common rainfall catchment. A 100 square-meter (930 squarefoot) roof intercepting 1 meter (3.28 feet) of rainfall per year provides, on average,
274 liters (71.2 gallons) of water per day. This amount is roughly 75 percent of a
typical North American person's domestic consumption, 180 percent of a French
person's average, and nearly seven times the per capita average in some developing
regions. Alternatives to roof catchments include airport runways in the Pacific Islands,
paved hillsides in the Caribbean, and earthen courtyards in China.
Cisterns.
The cistern, whether a clay pot in Thailand or a reinforcedconcrete community
reservoir in Kenya, provides the rainwater system the capacity to function through
droughts. Not all storage is in tank cisterns. Hand-dug mortared subterranean vaults
are found in the Middle East. Japanese construct rock-filled containments beneath
ground to serve as artificial aquifers into which intercepted rainwater is directed for
subsequent pumping.
The less uniformly that rainfall occurs over a year, the greater the required storage
volume. It is not uncommon for cisterns to be sized to hold a 30-day water supply.
Cisterns in Australia can store a half-year's supply accumulated in the monsoon
season. Cisterns of only a week's capacity may be sufficient in the tropics. Because
droughts are unpredictable, rainfall harvesting always carries with it some degree of
risk.
Catchment-Cistern Conveyances.
Roof gutters are the most common conveyances between catchment and cistern.
Rainwater harvesting often fails to achieve its potential yield because an adequate
catchment is linked to an adequate cistern by an inadequate water trough that is
undersized or poorly maintained.
Withdrawal Methods.
Cisterns from which water is hand-drawn by a dipper are prone to human
contamination . Better systems are elevated so that water may be drawn down to
the user by gravity. Urban Singapore has systems in which rainwater is pumped into
an elevated tank for pressurized distribution.
Where drinkable water is available from another source, but in limited quantity,
rainwater can be employed as greywater . A separate rain-fed pipe network services
toilets, laundry facilities, and lawn irrigation.
Not all rainwater harvesting is for domestic supply. Traditional aridland agriculture
captures infrequent rainfall through landscape improvement. Iranian farmers
construct berms in the shape of an uphill "v" in order to funnel rainfall to individual
trees. Native Americans terrace cornfields to capture infrequent summer
thunderstorms.
Rooftop catchments: In the most basic form of this technology, rainwater is collected in simple vessels
at the edge of the roof. Variations on this basic approach include collection of rainwater in gutters which
drain to the collection vessel through down-pipes constructed for this purpose, and/or the diversion of
rainwater from the gutters to containers for settling particulates before being conveyed to the storage
container for the domestic use. As the rooftop is the main catchment area, the amount and quality of
rainwater collected depends on the area and type of roofing material. Reasonably pure rainwater can
be collected from roofs constructed with galvanized corrugated iron, aluminium or asbestos cement
sheets, tiles and slates, although thatched roofs tied with bamboo gutters and laid in proper slopes can
produce almost the same amount of runoff less expensively (Gould, 1992). However, the bamboo roofs
are least suitable because of possible health hazards. Similarly, roofs with metallic paint or other
coatings are not recommended as they may impart tastes or colour to the collected water. Roof
catchments should also be cleaned regularly to remove dust, leaves and bird droppings so as to
maintain the quality of the product water (see figure 1).
Land surface catchments: Rainwater harvesting using ground or land surface catchment areas is less
complex way of collecting rainwater. It involves improving runoff capacity of the land surface through
various techniques including collection of runoff with drain pipes and storage of collected water.
Compared to rooftop catchment techniques, ground catchment techniques provide more opportunity for
collecting water from a larger surface area. By retaining the flows (including flood flows) of small creeks
and streams in small storage reservoirs (on surface or underground) created by low cost (e.g., earthen)
dams, this technology can meet water demands during dry periods. There is a possibility of high rates
of water loss due to infiltration into the ground, and, because of the often marginal quality of the water
collected, this technique is mainly suitable for storing water for agricultural purposes. Various
techniques available for increasing the runoff within ground catchment areas involve: i) clearing or
altering vegetation cover, ii) increasing the land slope with artificial ground cover, and iii) reducing soil
permeability by the soil compaction and application of chemicals (see figure 2).
Clearing or altering vegetation cover: Clearing vegetation from the ground can increase surface runoff
but also can induce more soil erosion. Use of dense vegetation cover such as grass is usually
suggested as it helps to both maintain an high rate of runoff and minimize soil erosion.
Increasing slope: Steeper slopes can allow rapid runoff of rainfall to the collector. However, the rate of
runoff has to be controlled to minimise soil erosion from the catchment field. Use of plastic sheets,
asphalt or tiles along with slope can further increase efficiency by reducing both evaporative losses and
soil erosion. The use of flat sheets of galvanized iron with timber frames to prevent corrosion was
recommended and constructed in the State of Victoria, Australia, about 65 years ago (Kenyon, 1929;
cited in UNEP, 1982).
Soil compaction by physical means: This involves smoothing and compacting of soil surface using
equipment such as graders and rollers. To increase the surface runoff and minimize soil erosion rates,
conservation bench terraces are constructed along a slope perpendicular to runoff flow. The bench
terraces are separated by the sloping collectors and provision is made for distributing the runoff evenly
across the field strips as sheet flow. Excess flows are routed to a lower collector and stored (UNEP,
1982).
Soil compaction by chemical treatments: In addition to clearing, shaping and compacting a catchment
area, chemical applications with such soil treatments as sodium can significantly reduce the soil
permeability. Use of aqueous solutions of a silicone-water repellent is another technique for enhancing
soil compaction technologies. Though soil permeability can be reduced through chemical treatments,
soil compaction can induce greater rates of soil erosion and may be expensive. Use of sodium-based
chemicals may increase the salt content in the collected water, which may not be suitable both for
drinking and irrigation purposes.
B) Collection Devices
Storage tanks: Storage tanks for collecting rainwater harvested using guttering may be either above or
below the ground. Precautions required in the use of storage tanks include provision of an adequate
enclosure to minimise contamination from human, animal or other environmental contaminants, and a
tight cover to prevent algal growth and the breeding of mosquitos. Open containers are not
recommended for collecting water for drinking purposes. Various types of rainwater storage facilities
can be found in practice. Among them are cylindrical ferrocement tanks and mortar jars. The
ferrocement tank consists of a lightly reinforced concrete base on which is erected a circular vertical
cylinder with a 10 mm steel base. This cylinder is further wrapped in two layers of light wire mesh to
form the frame of the tank. Mortar jars are large jar shaped vessels constructed from wire reinforced
mortar. The storage capacity needed should be calculated to take into consideration the length of any
dry spells, the amount of rainfall, and the per capita water consumption rate. In most of the Asian
countries, the winter months are dry, sometimes for weeks on end, and the annual average rainfall can
occur within just a few days. In such circumstances, the storage capacity should be large enough to
cover the demands of two to three weeks. For example, a three person household should have a
minimum capacity of 3 (Persons) x 90 (l) x 20 (days) = 5 400 l.
Rainfall water containers: As an alternative to storage tanks, battery tanks (i.e., interconnected tanks)
made of pottery, ferrocement, or polyethylene may be suitable. The polyethylene tanks are compact but
have a large storage capacity (ca. 1 000 to 2 000 l), are easy to clean and have many openings which
can be fitted with fittings for connecting pipes. In Asia, jars made of earthen materials or ferrocement
tanks are commonly used. During the 1980s, the use of rainwater catchment technologies, especially
roof catchment systems, expanded rapidly in a number of regions, including Thailand where more than
ten million 2 m3 ferrocement rainwater jars were built and many tens of thousands of larger ferrocement
tanks were constructed between 1991 and 1993. Early problems with the jar design were quickly
addressed by including a metal cover using readily available, standard brass fixtures. The immense
success of the jar programme springs from the fact that the technology met a real need, was affordable,
and invited community participation. The programme also captured the imagination and support of not
only the citizens, but also of government at both local and national levels as well as community based
organizations, small-scale enterprises and donor agencies. The introduction and rapid promotion of
Bamboo reinforced tanks, however, was less successful because the bamboo was attacked by termites,
bacteria and fungus. More than 50 000 tanks were built between 1986 and 1993 (mainly in Thailand
and Indonesia) before a number started to fail, and, by the late 1980s, the bamboo reinforced tank
design, which had promised to provide an excellent low-cost alternative to ferrocement tanks, had to be
abandoned.
C) Conveyance Systems
Conveyance systems are required to transfer the rainwater collected on the rooftops to the storage tanks. This
is usually accomplished by making connections to one or more down-pipes connected to the rooftop gutters.
When selecting a conveyance system, consideration should be given to the fact that, when it first starts to rain,
dirt and debris from the rooftop and gutters will be washed into the down-pipe. Thus, the relatively clean water
will only be available some time later in the storm. There are several possible choices to selectively collect
clean water for the storage tanks. The most common is the down-pipe flap. With this flap it is possible to direct
the first flush of water flow through the down-pipe, while later rainfall is diverted into a storage tank. When it
starts to rain, the flap is left in the closed position, directing water to the down-pipe, and, later, opened when
relatively clean water can be collected. A great disadvantage of using this type of conveyance control system
is the necessity to observe the runoff quality and manually operate the flap. An alternative approach would be
to automate the opening of the flap as described below.
A funnel-shaped insert is integrated into the down-pipe system. Because the upper edge of the funnel is not in
direct contact with the sides of the down-pipe, and a small gap exists between the down-pipe walls and the
funnel, water is free to flow both around the funnel and through the funnel. When it first starts to rain, the
volume of water passing down the pipe is small, and the *dirty* water runs down the walls of the pipe, around
the funnel and is discharged to the ground as is normally the case with rainwater guttering. However, as the
rainfall continues, the volume of water increases and *clean* water fills the down-pipe. At this higher volume,
the funnel collects the clean water and redirects it to a storage tank. The pipes used for the collection of
rainwater, wherever possible, should be made of plastic, PVC or other inert substance, as the pH of rainwater
can be low (acidic) and could cause corrosion, and mobilization of metals, in metal pipes.
In order to safely fill a rainwater storage tank, it is necessary to make sure that excess water can overflow, and
that blockages in the pipes or dirt in the water do not cause damage or contamination of the water supply. The
design of the funnel system, with the drain-pipe being larger than the rainwater tank feed-pipe, helps to ensure
that the water supply is protected by allowing excess water to bypass the storage tank. A modification of this
design is shown in Figure 5, which illustrates a simple overflow/bypass system. In this system, it also is
possible to fill the tank from a municipal drinking water source, so that even during a prolonged drought the
tank can be kept full. Care should be taken, however, to ensure that rainwater does not enter the drinking
water distribution system.
Extent of Use
The history of rainwater harvesting in Asia can be traced back to about the 9th or 10th Century and the smallscale collection of rainwater from roofs and simple brush dam constructions in the rural areas of South and
South-east Asia. Rainwater collection from the eaves of roofs or via simple gutters into traditional jars and pots
has been traced back almost 2 000 years in Thailand (Prempridi and Chatuthasry, 1982). Rainwater
harvesting has long been used in the Loess Plateau regions of China. More recently, however, about 40 000
well storage tanks, in a variety of different forms, were constructed between 1970 and 1974 using a
technology which stores rainwater and stormwater runoff in ponds of various sizes. A thin layer of red clay is
generally laid on the bottom of the ponds to minimize seepage losses. Trees, planted at the edges of the
ponds, help to minimize evaporative losses from the ponds (UNEP, 1982).
Cultural Acceptability
Rainwater harvesting is an accepted freshwater augmentation technology in Asia. While the bacteriological
quality of rainwater collected from ground catchments is poor, that from properly maintained rooftop catchment
systems, equipped with storage tanks having good covers and taps, is generally suitable for drinking, and
frequently meets WHO drinking water standards. Notwithstanding, such water generally is of higher quality
than most traditional, and many of improved, water sources found in the developing world. Contrary to popular
beliefs, rather than becoming stale with extended storage, rainwater quality often improves as bacteria and
pathogens gradually die off (Wirojanagud et al., 1989). Rooftop catchment, rainwater storage tanks can
provide good quality water, clean enough for drinking, as long as the rooftop is clean, impervious, and made
from non-toxic materials (lead paints and asbestos roofing materials should be avoided), and located away
from over-hanging trees since birds and animals in the trees may defecate on the roof.
Specification
Maintenance is generally limited to the annual cleaning of the tank and regular inspection of the gutters and
down-pipes. Maintenance typically consists of the removal of dirt, leaves and other accumulated materials.
Such cleaning should take place annually before the start of the major rainfall season. However, cracks in the
storage tanks can create major problems and should be repaired immediately. In the case of ground and rock
catchments, additional care is required to avoid damage and contamination by people and animals, and
proper fencing is required.
Advantages
Rainwater harvesting technologies are simple to install and operate. Local people can be easily trained to
implement such technologies, and construction materials are also readily available. Rainwater harvesting is
convenient in the sense that it provides water at the point of consumption, and family members have full
control of their own systems, which greatly reduces operation and maintenance problems. Running costs,
also, are almost negligible. Water collected from roof catchments usually is of acceptable quality for domestic
purposes. As it is collected using existing structures not specially constructed for the purpose, rainwater
harvesting has few negative environmental impacts compared to other water supply project technologies.
Although regional or other local factors can modify the local climatic conditions, rainwater can be a continuous
source of water supply for both the rural and poor. Depending upon household capacity and needs, both the
water collection and storage capacity may be increased as needed within the available catchment area.
Disadvantages
Disadvantages of rainwater harvesting technologies are mainly due to the limited supply and uncertainty of
rainfall. Adoption of this technology requires a *bottom up* approach rather than the more usual *top down*
approach employed in other water resources development projects. This may make rainwater harvesting less
attractive to some governmental agencies tasked with providing water supplies in developing countries, but the
mobilization of local government and NGO resources can serve the same basic role in the development of
rainwater-based schemes as water resources development agencies in the larger, more traditional public
water supply schemes.
Suitability
The augmentation of municipal water supplies with harvested rainwater is suited to both urban and rural areas.
The construction of cement jars or provision of gutters does not require very highly skilled manpower.
Development Costs
The capital cost of rainwater harvesting systems is highly dependent on the type of catchment, conveyance
and storage tank materials used. However, the cost of harvested rainwater in Asia, which varies from $0.17 to
$0.37 per cubic metre of water storage, is relatively low compared to many countries in Africa (Lee and
Vissher, 1990).
Compared to deep and shallow tubewells, rainwater collection systems are more cost effective, especially if
the initial investment does not include the cost of roofing materials. The initial per unit cost of rainwater storage
tanks (jars) in Northeast Thailand is estimated to be about $1/l, and each tank can last for more than ten
years. The reported operation and maintenance costs are negligible.
Effectivness of Technology
The feasibility of rainwater harvesting in a particular locality is highly dependent upon the amount and intensity
of rainfall. Other variables, such as catchment area and type of catchment surface, usually can be adjusted
according to household needs. As rainfall is usually unevenly distributed throughout the year, rainwater
collection methods can serve as only supplementary sources of household water. The viability of rainwater
harvesting systems is also a function of: the quantity and quality of water available from other sources;
household size and per capita water requirements; and budget available. The decision maker has to balance
the total cost of the project against the available budget, including the economic benefit of conserving water
supplied from other sources. Likewise, the cost of physical and environmental degradation associated with the
development of available alternative sources should also be calculated and added to the economic analysis.
Assuming that rainwater harvesting has been determined to be feasible, two kinds of techniques--statistical
and graphical methods--have been developed to aid in determining the size of the storage tanks. These
methods are applicable for rooftop catchment systems only, and detail guidelines for design of these storage
tanks can be found in Gould (1991) and Pacey and Cullis (1986, 1989).
Accounts of serious illness linked to rainwater supplies are few, suggesting that rainwater harvesting
technologies are effective sources of water supply for many household purposes. It would appear that the
potential for slight contamination of roof runoff from occasional bird droppings does not represent a major
health risk; nevertheless, placing taps at least 10 cm above the base of the rainwater storage tanks allows any
debris entering the tank to settle on the bottom, where it will not affect the quality of the stored water, provided
it remains undisturbed. Ideally, storage tanks should cleaned annually, and sieves should fitted to the gutters
and down-pipes to further minimize particulate contamination. A coarse sieve should be fitted in the gutter
where the down-pipe is located. Such sieves are available made of plastic coated steel-wire or plastic, and
may be wedged on top and/or inside gutter and near the down-pipe. It is also possible to fit a fine sieve within
the down-pipe itself, but this must be removable for cleaning. A fine filter should also be fitted over the outlet of
the down-pipe as the coarser sieves situated higher in the system may pass small particulates such as leaf
fragments, etc. A simple and very inexpensive method is to use a small, fabric sack, which may be secured
over the feed-pipe where it enters the storage tank.
If rainwater is used to supply household appliances such as the washing machine, even the tiniest particles of
dirt may cause damage to the machine and the washing. To minimize the occurrence of such damage, it is
advisable to install a fine filter of a type which is used in drinking water systems in the supply line upstream of
the appliances. For use in wash basins or bath tubs, it is advisable to sterilise the water using a chlorine
dosage pump.
For centuries, people have relied on rainwater harvesting to supply water for
household, landscape, livestock, and agricultural uses. Before large centralized water
supply systems were developed, rainwater was collected from roofs and stored on
site in tanks known as cisterns.
With the development of large, reliable water treatment and distribution systems and
more affordable well drilling equipment, rain harvesting systems have been all but
forgotten, even though they offer a source of pure, soft, low sodium water.
collection systems
11.
We offer various facilities for rain water harvesting systems for agricultural farms. Our range
for rain water harvesting system comprises of rigid PVC pipes and water storage tanks. Our
products ensure effective rain harvesting in agricultural farms and help reducing the depleting
ground water level. Some of the advantages of our rain harvesting comprises of the following:
Rust proof
Leak proof
Less maintenance
Durable