Professional Documents
Culture Documents
PIES Catalogue
PIES Catalogue
MOTION CONTROL
P.I.E.S. Australia Pty Ltd is the leading Australasian distributor for polyurethane timing belts and
pulleys. A wholly Australian owned, family business formed in 1978, PIES is the sole
Australian agents for Synchroflex, Breco and Brecoflex polyurethane belting products. Pies
also design, manufacture, import and export timing belts and pulleys.
Contents
Page No.
Introduction
T2, M
T2.5
T5
T10
T20
11
AT3
13
AT5
14
AT10
16
AT20
18
20
22
Special Belts
23
24
29
30
32
Formulae
Components
39
Idler Pulleys
40
Slider Beds
42
Tension Plates
43
Locking devices
44
Tensioning
46
Contact Details
Belt
48
Power Range
R.P.M
Speed
M/T2/T2.5
0-0.5 kW
0-40,000 rpm
0-80 m/s
T5
0-5 kW
0-40,000 rpm
0-80 m/s
T10
0-30 kW
0-15,000 rpm
0-60 m/s
T20
0-100 kW
0-6,000 rpm
0-40 m/s
AT3
0-5 kW
0-40,000 rpm
0-80 m/s
AT5
0-15 kW
0-40,000 rpm
0-80 m/s
AT10
0-70 kW
0-15,000 rpm
0-60 m/s
AT20
0-250 kW
0-6,000 rpm
0-40 m/s
Synchroflex
Synchroflex timing belts are made from a wear resistant Contilan polyurethane with
high quality steel tension members. The excellent bond between the two creates a belt
with high load bearing properties and exceptional span rigidity which means no post
elongation. The moulding process produces close tolerance timing belts allowing them
to be run smoothly at high rotational speeds. Synchroflex belts can also be used for
indexing and conveying and can also have lugs welded to the belt back.
Properties:
Breco / Brecoflex
Breco belts come in three styles.
Breco-M: Open length belting mainly used for linear drives. Reels are extruded to 50
and 100m lengths, although shorter lengths can be cut.
Breco-V: Joined to length belting are made from lengths of Breco-M and are used
for indexing, conveying and power transmission applications particularly when long
centre distances are invloved. Profiles and backings can also be applied to these belts.
Brecoflex: Fully moulded endless timing belts used for power transmission
applications. These belts have no joint and a continuous steel tension member.
T2 (2mm pitch)
T2 TYPE
0.6
2.0
Belt No
0.5
40
0.7
T2 Single sided
M (2.032mm pitch)
0.51
0.64
2.032
40
10
M (MXL) TYPE
Length
mm
No. of
Teeth
Belt No
Length
mm
No. of
Teeth
T2/90
T2/108
T2/118
T2/120
T2/138
90
108
118
120
138
45
54
59
60
69
M 111
M 113
M 121
M 132
M 142
111.76
113.79
121.92
132.08
142.24
55
56
60
65
70
T2/140
T2/144
T2/150
T2/160
T2/180
140
144
150
160
180
70
72
75
80
90
M 144
M 162
M 182
M 197
M 203
144.27
162.56
182.88
197.10
203.20
71
80
90
97
100
T2/200
T2/220
T2/240
T2/256
T2/262
200
220
240
256
262
100
110
120
128
131
M 209
M 213
M 243
M 256
M 264
209.30
213.36
243.86
256.03
264.16
103
105
120
126
130
T2/280
T2/292
T2/320
T2/360
T2/600
280
292
320
360
600
140
146
160
180
300
M 284
M 304
M 355
M 373
M 449
284.48
304.80
355.60
373.89
449.07
140
150
175
184
221
T2/710
710
355
M 503
M 520
M 599
M 731
M 1178
503.94
520.19
599.44
731.52
1178.56
248
256
295
360
580
0.76
Belt weight
T2
0.011kg/m
0.012kg/m
10
Synchroflex
24
40
80
Type
teeth
T2
AL16T2/15-0
AL16T2/16-0
AL16T2/20-0
3
3
3
15
16
20
AL16T2/24-2
AL16T2/32-2
AL16T2/48-2
6F
6F
6F
M
AL16M/15-0
AL16M/16-0
AL16M/20-0
AL16M/24-2
AL16M/32-2
AL16M/48-2
Pcd
Od
Dm
Df
9.55
10.19
12.73
9.00
9.64
12.18
16
16
16
3
3
3
24
32
48
15.28
20.37
30.56
14.73
19.82
30.01
10
14
20
18
24
35
10
10
10
16
16
16
3
3
4
3
3
3
15
16
20
9.70
10.35
12.94
9.19
9.84
12.43
16
16
16
3
3
3
6F
6F
6F
24
32
48
15.52
20.70
31.05
15.01
20.19
30.54
10
14
20
18
24
35
10
10
10
16
16
16
3
3
4
Pcd
Od
d
4
Type 3
Weight
Length
mm
1.0
T2.5/ 55
T2.5/120
T2.5/145
T2.5/160
T2.5/177.5
55
120
145
160
177.5
22
48
58
64
71
T2.5/180
T2.5/182.5
T2.5/200
T2.5/210
T2.5/225
180
182.5
200
210
225
72
73
80
84
90
230
245
265
285
290
92
98
106
114
116
305
317.5
122
127
T2.5/230
T2.5/245
T2.5/265
T2.5/285
T2.5/290
40
Belt No
Length
mm
T2.5/330
T2.5/380
T2.5/395
330
380
395
132
152
158
T2.5/420
T2.5/480
T2.5/500
T2.5/540
T2.5/600
420
480
500
540
600
168
192
200
216
240
T2.5/620
T2.5/650
T2.5/780
T2.5/950
T2.5/1300
T2.5/1475
620
650
780
950
1300
1475
248
260
312
380
520
590
DOUBLE SIDED
T2.5/317.5-DL
T2.5/415-DL
T2.5/457.5-DL
317.5
415
457.5
T2.5
T2.5-DL
0.015kg/m
0.016kg/m
L
F
10
Synchroflex
39
65
117
Breco- M
32
55
98
Dm
Pcd
Od
d
Width (mm)
127
166
183
Belt weight
1.0
No. of
Teeth
Type 6
0.6
0.7
T2.5/305
T2.5/317.5
0.7
No. of
Teeth
Od
0.7
40
10
Pcd
0.6
2.5
Dm
Type 1F
Dm
Df
Pcd
Od
d
Type 6F
Pulley No.
Type
teeth
Pcd
Od
Dm
Df
Weight
AL16T2.5/10-2
AL16T2.5/12-2
AL16T2.5/14-2
AL16T2.5/15-2
AL16T2.5/16-2
1F
1F
1F
1F
1F
10
12
14
15
16
7.96
9.55
11.14
11.94
12.73
7.45
9.00
10.60
11.40
12.20
10
12
14
15
16
10
12
14
15
16
10
10
10
10
10
16
16
16
16
16
0.002
0.003
0.004
0.005
0.005
AL16T2.5/18-2
AL16T2.5/19-2
AL16T2.5/20-2
AL16T2.5/22-2
AL16T2.5/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
14.32
15.12
15.92
17.51
19.10
13.80
14.60
15.40
17.00
18.55
10
10
12
12
14
17.5
18
19.5
23
23
10
10
10
10
10
16
16
16
16
16
4
4
4
4
4
0.006
0.007
0.008
0.009
0.012
AL16T2.5/25-2
AL16T2.5/26-2
AL16T2.5/28-2
AL16T2.5/30-2
AL16T2.5/32-2
6F
6F
6F
6F
6F
25
26
28
30
32
19.89
20.69
22.28
23.87
25.46
19.35
20.15
21.75
23.35
24.95
14
14
14
16
16
23
25
25
28
32
10
10
10
10
10
16
16
16
16
16
4
4
4
6
6
0.013
0.014
0.016
0.018
0.020
AL16T2.5/36-2
AL16T2.5/40-2
AL16T2.5/44-0
AL16T2.5/48-0
AL16T2.5/60-0
6F
6F
6
6
6
36
40
44
48
60
28.65
31.83
35.01
38.20
47.75
28.15
31.30
34.51
37.70
47.25
20
22
24
26
34
36
38
-
10
10
10
10
10
16
16
16
16
16
6
6
6
6
8
0.026
0.032
0.040
0.048
0.073
AL16T2.5/72-0
AL16T2.5/90-0
6
6
72
90
57.30
71.62
56.80
71.10
40
50
10
10
16
16
8
8
0.087
0.137
T5 (5mm pitch)
10
16
25
Length
No. of
Belt No
Length
No. of
5.0
1.2
40
1.8
T5 Single sided
1.2
5.0
1.2
40
1.8
T5
T5-DL
0.024kg/m
0.027kg/m
20
30
33
36
37
T5/630
T5/650
T5/690
T5/700
T5/720
630
650
690
700
720
126
130
138
140
144
T5/200
T5/210
T5/215
T5/220
T5/225
200
210
215
220
225
40
42
43
44
45
T5/725
T5/750
T5/765
T5/780
T5/800
725
750
765
780
800
145
150
153
156
160
T5/245
T5/250
T5/255
T5/260
T5/270
245
250
255
260
270
49
50
51
52
54
T5/815
T5/840
T5/900
T5/920
T5/925
815
840
900
920
925
163
168
180
184
185
T5/280
T5/295
T5/305
T5/330
T5/340
280
295
305
330
340
56
59
61
66
68
T5/940
T5/990
T5/1075
T5/1100
T5/1160
940
990
1075
1100
1160
188
198
215
220
232
T5/355
T5/365
T5/390
T5/400
T5/410
355
365
390
400
410
71
73
78
80
82
T5/1215
T5/1315
T5/1380
T5/1500
1215
1315
1380
1500
243
263
276
300
T5/420
T5/455
T5/460
T5/480
T5/500
420
455
460
480
500
84
91
92
96
100
T5/150 DL
T5/260 DL
T5/300 DL
T5/410 DL
T5/460 DL
150
260
300
410
460
30
52
60
82
92
T5/505
T5/510
T5/525
T5/545
T5/550
505
510
525
545
550
101
102
105
109
110
T5/515 DL
T5/525 DL
T5/590 DL
T5/620 DL
T5/625 DL
515
525
590
620
625
103
105
118
124
125
T5/560
T5/575
T5/590
T5/610
T5/620
560
575
590
610
620
112
115
118
122
124
T5/750 DL
T5/815 DL
T5/860 DL
T5/940 DL
T5/1100 DL
T5/1325 DL
750
815
860
940
1100
1325
150
163
172
188
220
265
3.2
100
150
165
180
185
Breco-M
Breco- V
41.8
5.5
T5/100
T5/150
T5/165
T5/180
T5/185
25
Part No
10T5-Clamp
16T5-Clamp
25T5-Clamp
10
16
25
32
50
Synchroflex
180
330
570
930
1200
1920
Breco- M
180
300
540
840
1080
1680
Breco- V
90
150
270
420
540
840
Brecoflex
180
330
570
930
1200
1920
8.2
T5-Clamp Plate
Code No
270310
270316
270325
Width (mm)
PIES T5 pulleys
T5 (5mm pitch)
Dm
Df
Pcd
Od
d
Type
teeth
Pcd
Od
Dm
Df
Weight
AL21T5/10-2
AL21T5/12-2
AL21T5/14-2
AL21T5/15-2
AL21T5/16-2
6F
6F
6F
6F
6F
10
12
14
15
16
15.92
19.10
22.29
23.88
25.47
15.05
18.25
21.45
23.05
24.60
8
11
14
16
18
19.5
23.0
25.0
28.0
32.0
15
15
15
15
15
21
21
21
21
21
6
6
0.012
0.016
0.016
0.021
0.025
AL21T5/18-2
AL21T5/19-2
AL21T5/20-2
AL21T5/22-2
AL21T5/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
28.65
30.25
31.83
35.02
38.21
27.80
29.40
31.00
34.25
37.40
20
22
23
24
26
32.0
36.0
36.0
38.0
42.0
15
15
15
15
15
21
21
21
21
21
6
6
6
6
6
0.031
0.036
0.038
0.046
0.054
AL21T5/25-2
AL21T5/26-2
AL21T5/27-2
AL21T5/28-2
AL21T5/30-2
6F
6F
6F
6F
6F
25
26
27
28
30
39.80
41.39
42.98
44.58
47.76
39.00
40.60
42.20
43.75
46.95
26
26
30
32
34
44.0
44.0
48.0
48.0
51.0
15
15
15
15
15
21
21
21
21
21
6
6
8
8
8
0.058
0.062
0.064
0.071
0.075
AL21T5/32-2
AL21T5/36-2
AL21T5/40-2
AL21T5/48-0
AL21T5/60-0
6F
6F
6F
6
6
32
36
40
48
60
50.94
57.31
63.66
76.42
95.52
50.10
56.45
62.85
75.55
94.65
38
38
40
50
65
54.0
63.0
66.0
_
_
15
15
15
15
15
21
21
21
21
21
8
8
8
8
8
0.088
0.114
0.138
0.200
0.307
Type
teeth
Pcd
Od
Dm
Df
Weight
AL27T5/10-2
AL27T5/12-2
AL27T5/14-2
AL27T5/15-2
AL27T5/16-2
6F
6F
6F
6F
6F
10
12
14
15
16
15.92
19.10
22.29
23.88
25.47
15.05
18.25
21.45
23.05
24.60
8
11
14
16
18
19.5
23.0
25.0
28.0
32.0
21
21
21
21
21
27
27
27
27
27
6
6
0.016
0.022
0.026
0.029
0.035
AL27T5/18-2
AL27T5/19-2
AL27T5/20-2
AL27T5/22-2
AL27T5/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
28.65
30.25
31.83
35.02
38.21
27.80
29.40
31.00
34.25
37.40
20
22
23
24
26
32.0
36.0
36.0
38.0
42.0
21
21
21
21
21
27
27
27
27
27
6
6
6
6
6
0.043
0.049
0.053
0.054
0.076
AL27T5/25-2
AL27T5/26-2
AL27T5/27-2
AL27T5/28-2
AL27T5/30-2
6F
6F
6F
6F
6F
25
26
27
28
30
39.80
41.39
42.98
44.58
47.76
39.00
40.60
42.20
43.75
46.95
26
26
30
32
34
44.0
44.0
48.0
48.0
51.0
21
21
21
21
21
27
27
27
27
27
6
6
8
8
8
0.081
0.085
0.090
0.092
0.105
AL27T5/32-2
AL27T5/36-2
AL27T5/40-2
AL27T5/48-0
AL27T5/60-0
6F
6F
6F
6
6
32
36
40
48
60
50.94
57.31
63.66
76.42
95.52
50.10
56.45
62.85
75.55
94.65
38
38
40
50
65
54.0
63.0
66.0
_
_
21
21
21
21
21
27
27
27
27
27
8
8
8
8
8
0.123
0.160
0.193
0.280
0.430
Type 6F
Dm
Pcd
Od
d
Type 6
Type
teeth
Pcd
Od
Dm
Df
Weight
AL36T5/10-2
AL36T5/12-2
AL36T5/14-2
AL36T5/15-2
AL36T5/16-2
6F
6F
6F
6F
6F
10
12
14
15
16
15.92
19.10
22.29
23.88
25.47
15.05
18.25
21.45
23.05
24.60
8
11
14
16
18
19.5
23.0
25.0
28.0
32.0
30
30
30
30
30
36
36
36
36
36
6
6
0.023
0.031
0.037
0.041
0.050
AL36T5/18-2
AL36T5/19-2
AL36T5/20-2
AL36T5/22-2
AL36T5/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
28.65
30.25
31.83
35.02
38.21
27.80
29.40
31.00
34.25
37.40
20
22
23
24
26
32.0
36.0
36.0
38.0
42.0
30
30
30
30
30
36
36
36
36
36
6
6
6
6
6
0.061
0.070
0.076
0.080
0.109
AL36T5/25-2
AL36T5/26-2
AL36T5/27-2
AL36T5/28-2
AL36T5/30-2
6F
6F
6F
6F
6F
25
26
27
28
30
39.80
41.39
42.98
44.58
47.76
39.00
40.60
42.20
43.75
46.95
26
26
30
32
34
44.0
44.0
48.0
48.0
51.0
30
30
30
30
30
36
36
36
36
36
6
6
8
8
8
0.116
0.120
0.128
0.126
0.150
AL36T5/32-2
AL36T5/36-2
AL36T5/40-2
AL36T5/48-0
AL36T5/60-0
6F
6F
6F
6
6
32
36
40
48
60
50.94
57.31
63.66
76.42
95.52
50.10
56.45
62.85
75.55
94.65
38
38
40
50
65
54.0
63.0
66.0
_
_
30
30
30
30
30
36
36
36
36
36
8
8
8
8
8
0.176
0.230
0.276
0.400
0.614
10
2.5
40
3.5
2.5
10
2.5
40
3.5
T10
0.048kg/m
T10-DL
0.057kg/m
32
50
Length
mm
No. of
Teeth
Belt No
Length
mm
No. of
Teeth
260
350
370
410
440
26
35
37
41
44
T10/1350
T10/1390
T10/1400
T10/1420
T10/1450
1350
1390
1400
1420
1450
135
139
140
142
145
T10/450
T10/500
T10/530
T10/560
T10/600
450
500
530
560
600
45
50
53
56
60
T10/1460
T10/1500
T10/1560
T10/1610
T10/1750
1460
1500
1560
1610
1750
146
150
156
161
175
T10/610
T10/630
T10/660
T10/680
T10/690
610
630
660
680
690
61
63
66
68
69
T10/1780
T10/1880
T10/1960
T10/2250
T10/3100
1780
1880
1960
2250
3100
178
188
196
225
310
T10/700
T10/720
T10/730
T10/750
T10/760
700
720
730
750
760
70
72
73
75
76
T10/4780
4780
478
T10/780
T10/810
T10/840
T10/850
T10/880
780
810
840
850
880
78
81
84
85
88
T10/260
T10/530
T10/630
T10/660
T10/720
DL
DL
DL
DL
DL
260
530
630
660
720
26
53
63
66
72
T10/890
T10/920
T10/960
T10/970
T10/980
890
920
960
970
980
89
92
96
97
98
T10/840 DL
T10/980 DL
T10/1210DL
T10/1240DL
T10/1250DL
840
980
1210
1240
1250
84
98
121
124
125
T10/1010
T10/1080
T10/1110
T10/1140
T10/1150
1010
1080
1110
1140
1150
101
108
111
114
115
T10/1320DL
T10/1350DL
T10/1420DL
T10/1610DL
T10/1880DL
1320
1350
1420
1610
1880
132
135
142
161
188
T10/1210
T10/1240
T10/1250
T10/1300
T10/1320
1210
1240
1250
1300
1320
121
124
125
130
132
T10/4780DL
4780
478
Breco-M
Breco- V
10 5
25
T10/260
T10/350
T10/370
T10/410
T10/440
15
16
50
16
25
32
50
75
100
Synchroflex
1200
2000
2700
4300
6600
8800
Breco- M
1300
2400
2600
4200
4900
6800
Breco- V
650
1200
1300
2100
2450
3400
Brecoflex
1000
1800
2300
3800
5800
7800
15
T10-Clamp Plate
Code No
270416
270425
270432
270450
Width (mm)
Part No
Belt Width "A" Clamp Width "B"
16T10-Clamp
16mm
41mm
25T10-Clamp
25mm
50mm
32T10-Clamp
32mm
57mm
50T10-Clamp
50mm
75mm
Dm
Df
Pcd
Od
d
Type
teeth
Pcd
AL31T10/10-2
AL31T10/12-2
AL31T10/14-2
AL31T10/15-2
AL31T10/16-2
6F
6F
6F
6F
6F
10
12
14
15
16
31.83
38.20
44.56
47.75
50.93
AL31T10/18-2
AL31T10/19-2
AL31T10/20-2
AL31T10/22-2
AL31T10/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
AL31T10/25-2
AL31T10/26-2
AL31T10/27-2
AL31T10/28-2
AL31T10/30-2
6F
6F
6F
6F
6F
AL31T10/32-2
AL31T10/36-2
AL31T10/40-2
AL31T10/48-0
AL31T10/60-0
6F
6F
6F
6
6
Od
Dm
Df
Weight
29.98
36.35
42.70
45.90
49.05
20
28
32
32
35
36
42
48
51
54
21
21
21
21
21
31
31
31
31
31
6
8
8
8
8
0.060
0.076
0.104
0.116
0.134
57.29
60.48
63.66
66.84
76.39
55.45
58.60
61.80
68.15
74.55
40
44
46
52
58
60
66
66
75
83
21
21
21
21
21
31
31
31
31
31
8
8
8
8
8
0.167
0.184
0.208
0.253
0.288
25
26
27
28
30
79.58
82.76
85.95
89.12
95.49
77.70
80.90
84.10
87.25
93.65
60
60
60
60
60
83
87
91
93
97
21
21
21
21
21
31
31
31
31
31
8
8
8
8
8
0.310
0.357
0.364
0.401
0.441
32
36
40
48
60
101.86
114.59
127.32
152.78
190.98
100.00
112.75
125.45
150.95
189.10
65
70
80
95
100
106
119
131
21
21
21
21
21
31
31
31
31
31
10
10
10
16
16
0.493
0.623
0.767
1.090
1.701
Type 6F
L
F
Pulley No.
Type
teeth
Pcd
AL40T10/10-2
AL40T10/12-2
AL40T10/14-2
AL40T10/15-2
AL40T10/16-2
6F
6F
6F
6F
6F
10
12
14
15
16
31.83
38.20
44.56
47.75
50.93
AL40T10/18-2
AL40T10/19-2
AL40T10/20-2
AL40T10/22-2
AL40T10/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
AL40T10/25-2
AL40T10/26-2
AL40T10/27-2
AL40T10/28-2
AL40T10/30-2
6F
6F
6F
6F
6F
AL40T10/32-2
AL40T10/36-2
AL40T10/40-2
AL40T10/48-0
AL40T10/60-0
6F
6F
6F
6
6
Od
Dm
Df
Weight
29.98
36.35
42.70
45.90
49.05
20
28
32
32
35
36
42
48
51
54
30
30
30
30
30
40
40
40
40
40
6
8
8
8
8
0.080
0.099
0.134
0.152
0.176
57.29
60.48
63.66
66.84
76.39
55.45
58.60
61.80
68.15
74.55
40
44
46
52
58
60
66
66
75
83
30
30
30
30
30
40
40
40
40
40
8
8
8
8
8
0.224
0.247
0.276
0.337
0.392
25
26
27
28
30
79.58
82.76
85.95
89.12
95.49
77.70
80.90
84.10
87.25
93.65
60
60
60
60
60
83
87
91
93
97
30
30
30
30
30
40
40
40
40
40
8
8
8
8
8
0.422
0.477
0.536
0.540
0.640
32
36
40
48
60
101.86
114.59
127.32
152.78
190.98
100.00
112.75
125.45
150.95
189.10
65
70
80
95
100
106
119
131
30
30
30
30
30
40
40
40
40
40
10
10
10
16
16
0.693
0.873
1.067
1.516
2.339
Dm
Pcd
Od
d
Type 6
Pulley No.
Type
teeth
Pcd
AL50T10/14-2
AL50T10/15-2
AL50T10/16-2
6F
6F
6F
14
15
16
44.56
47.75
50.93
AL50T10/18-2
AL50T10/19-2
AL50T10/20-2
AL50T10/22-2
AL50T10/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
AL50T10/25-2
AL50T10/26-2
AL50T10/27-2
AL50T10/28-2
AL50T10/30-2
6F
6F
6F
6F
6F
AL50T10/32-2
AL50T10/36-2
AL50T10/40-2
AL50T10/48-0
AL50T10/60-0
6F
6F
6F
6
6
Od
Dm
Df
Weight
42.70
45.90
49.05
32
32
35
48
51
54
40
40
40
50
50
50
12
12
12
0.155
0.180
0.203
57.29
60.48
63.66
66.84
76.39
55.45
58.60
61.80
68.15
74.55
40
44
46
52
58
60
66
66
75
83
40
40
40
40
40
50
50
50
50
50
12
12
12
12
12
0.253
0.286
0.322
0.393
0.475
25
26
27
28
30
79.58
82.76
85.95
89.12
95.49
77.70
80.90
84.10
87.25
93.65
60
60
60
60
60
83
87
91
93
97
40
40
40
40
40
50
50
50
50
50
12
12
12
12
12
0.527
0.564
0.602
0.642
0.740
32
36
40
48
60
101.86
114.59
127.32
152.78
190.98
100.00
112.75
125.45
150.95
189.10
65
70
80
95
100
106
119
131
40
40
40
40
40
50
50
50
50
50
12
16
16
16
16
0.844
1.063
1.317
1.931
3.004
Dm
Df
Pcd
Od
d
Type 6F
Type
teeth
Pcd
AL66T10/14-2
AL66T10/15-2
AL66T10/16-2
6F
6F
6F
14
15
16
44.56
47.75
50.93
AL66T10/18-2
AL66T10/19-2
AL66T10/20-2
AL66T10/22-2
AL66T10/24-2
6F
6F
6F
6F
6F
18
19
20
22
24
AL66T10/25-2
AL66T10/26-2
AL66T10/27-2
AL66T10/28-2
AL66T10/30-2
6F
6F
6F
6F
6F
AL66T10/32-2
AL66T10/36-2
AL66T10/40-2
AL66T10/48-0
AL66T10/60-0
6F
6F
6F
6
6
Od
Dm
Df
Weight
42.70
45.90
49.05
32
32
35
48
51
54
56
56
56
66
66
66
8
8
8
0.250
0.270
0.350
57.29
60.48
63.66
66.84
76.39
55.45
58.60
61.80
68.15
74.55
40
44
46
52
58
60
66
66
75
83
56
56
56
56
56
66
66
66
66
66
8
8
8
8
8
0.422
0.466
0.520
0.570
0.736
25
26
27
28
30
79.58
82.76
85.95
89.12
95.49
77.70
80.90
84.10
87.25
93.65
60
60
60
60
60
83
87
91
93
97
56
56
56
56
56
66
66
66
66
66
8
8
8
8
8
0.766
0.816
0.946
0.960
1.169
32
36
40
48
60
101.86
114.59
127.32
152.78
190.98
100.00
112.75
125.45
150.95
189.10
65
70
80
95
100
106
119
131
56
56
56
56
56
66
66
66
66
66
10
10
10
16
16
1.300
1.637
1.999
2.830
4.366
10
20
32
40
6.5
50
75
100
Belt No
Length
mm
No. of
Teeth
T20/1260
T20/1460
T20/1780
T20/1880
T20/2360
1260
1460
1780
1880
2360
63
73
89
94
118
T20/2600
T20/3100
T20/3620
2600
3100
3620
130
155
181
Belt No
Length
mm
No. of
Teeth
2600
3620
130
181
20
40
6.5
T20
0.084kg/m
T20-DL
0.111kg/m
Breco-M
Breco- V
200
20
6.5
160
20
Part No
25T20-Clamp
32T20-Clamp
50T20-Clamp
75T20-Clamp
100T20-Clamp
150T20-Clamp
Belt "A"
25mm
32mm
50mm
75mm
100mm
150mm
Width (mm)
25
32
50
75
100
150
Synchroflex
3700
4750
7750
Breco- M
3500
4500
6500
Breco- V
1750
2250
3250
5000
Brecoflex
3700
4750
7750
38mm
46mm
62mm
94mm
124mm
174mm
7000
10000
11
Dm
Df
Pcd
Od
d
Type
teeth
Pcd
Od
Dm
Df
AL53T20/18-2
AL53T20/20-2
AL53T20/22-2
AL53T20/24-2
AL53T20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
38
38
38
38
38
53
53
53
53
53
15
15
15
15
15
AL53T20/30-2
AL53T20/32-2
AL53T20/36-2
AL53T20/40-2
AL53T20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
38
38
38
38
38
53
53
53
53
53
15
18
18
20
20
AL53T20/60-0
AL53T20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
38
38
53
53
20
20
Weight
L
F
Pulley No.
Type
teeth
Pcd
Od
Dm
Df
AL71T20/18-2
AL71T20/20-2
AL71T20/22-2
AL71T20/24-2
AL71T20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
56
56
56
56
56
71
71
71
71
71
18
18
18
18
18
AL71T20/30-2
AL71T20/32-2
AL71T20/36-0
AL71T20/40-0
AL71T20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
56
56
56
56
56
71
71
71
71
71
18
20
20
20
24
AL71T20/60-0
AL71T20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
56
56
71
71
24
24
Weight
Dm
Pcd
Od
d
Type 6
Pulley No.
Type
teeth
Pcd
Od
Dm
Df
AL96T20/18-2
AL96T20/20-2
AL96T20/22-2
AL96T20/24-2
AL96T20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
81
81
81
81
81
96
96
96
96
96
24
24
24
24
24
AL96T20/30-2
AL96T20/32-0
AL96T20/36-0
AL96T20/40-0
AL96T20/48-0
6F
6
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
81
81
81
81
81
96
96
96
96
96
24
32
32
32
32
AL96T20/60-0
AL96T20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
81
81
96
96
32
32
Weight
L
F
12
Dm
Pcd
Od
d
Pulley No.
Type 6W
Type
teeth
Pcd
Od
Dm
Df
AL108T20/18-2
AL108T20/20-2
AL108T20/22-2
AL108T20/24-2
AL108T20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
108
108
108
108
108
123
123
123
123
123
24
24
24
24
24
AL108T20/30-2
AL108T20/32-2
AL108T20/36-0
AL108T20/40-0
AL108T20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
108
108
108
108
108
123
123
123
123
123
24
32
32
32
32
AL108T20/60-0
AL108T20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
108
108
123
123
32
32
Weight
T20 20mm Pitch pulleys are not available from stock and can be
manufactured to your personal requirements..
3.0
0.8
1.9
50
1.5
0.023kg/m
Dm
Df
Pcd
Od
d
Type 6F
L
F
Length
mm
No. of
Teeth
Belt No
Length
mm
No. of
Teeth
150
201
252
267
270
50
67
84
89
90
AT3/450
AT3/501
AT5/549
AT3/600
AT3/639
450
501
549
600
639
150
167
183
200
213
AT3/300
AT3/351
AT3/399
AT3/417
300
351
399
417
100
117
133
139
AT3/648
AT3/816
AT3/900
AT3/1011
648
816
900
1011
216
272
300
337
Width (mm)
AT3
16
10
AT3/150
AT3/201
AT3/252
AT3/267
AT3/270
Breco-M
10
16
20
25
Synchroflex
190
280
380
646
790
1102
Breco- M
180
260
360
570
725
Breco- V
90
130
180
285
360
Pcd
Od
Dm
Df
AL16AT3/15-2
AL16AT3/16-2
AL16AT3/18-2
AL16AT3/20-2
AL16AT3/24-2
Pulley No.
Type
6F
6F
6F
6F
6F
15
16
18
20
24
14.32
15.28
17.19
19.10
22.92
14.02
14.98
16.89
18.80
22.62
10
10
12
14
14
19
20
23
24
28
10
10
10
10
10
16
16
16
16
16
4
4
4
4
6
AL16AT3/25-2
AL16AT3/30-2
AL16AT3/32-2
AL16AT3/36-2
AL16AT3/40-2
6F
6F
6F
6F
6F
25
30
32
36
40
23.87
28.65
30.56
34.38
38.20
23.57
28.35
30.26
34.08
37.90
16
20
20
22
26
30
33
36
39
43
10
10
10
10
10
16
16
16
16
16
6
6
6
6
6
AL16AT3/48-0
AL16AT3/60-0
AL16AT3/72-0
6
6
6
48
60
72
45.84
57.30
68.75
54.54
57.00
68.45
34
38
50
10
10
10
16
16
16
6
6
6
Weight
Type
teeth
Pcd
Od
Dm
Df
AL21AT3/15-2
AL21AT3/16-2
AL21AT3/18-2
AL21AT3/20-2
AL21AT3/24-2
6F
6F
6F
6F
6F
15
16
18
20
24
14.32
15.28
17.19
19.10
22.92
14.02
14.98
16.89
18.80
22.62
10
10
12
14
14
19
20
23
24
28
15
15
15
15
15
21
21
21
21
21
4
4
4
4
6
AL21AT3/25-2
AL21AT3/30-2
AL21AT3/32-2
AL21AT3/36-2
AL21AT3/40-2
6F
6F
6F
6F
6F
25
30
32
36
40
23.87
28.65
30.56
34.38
38.20
23.57
28.35
30.26
34.08
37.90
16
20
20
22
26
30
33
36
39
43
15
15
15
15
15
21
21
21
21
21
6
6
6
6
6
AL21AT3/48-0
AL21AT3/60-0
AL21AT3/72-0
6
6
6
48
60
72
45.84
57.30
68.75
54.54
57.00
68.45
34
38
50
15
15
15
21
21
21
6
6
6
Weight
Dm
Pcd
Od
d
Pulley No.
Type 6
Type
teeth
Pcd
Od
Dm
Df
AL28AT3/15-2
AL28AT3/16-2
AL28AT3/18-2
AL28AT3/20-2
AL28AT3/24-2
6F
6F
6F
6F
6F
15
16
18
20
24
14.32
15.28
17.19
19.10
22.92
14.02
14.98
16.89
18.80
22.62
10
10
12
14
14
19
20
23
24
28
22
22
22
22
22
28
28
28
28
28
4
4
4
4
6
AL28AT3/25-2
AL28AT3/30-2
AL28AT3/32-2
AL28AT3/36-2
AL28AT3/40-2
6F
6F
6F
6F
6F
25
30
32
36
40
23.87
28.65
30.56
34.38
38.20
23.57
28.35
30.26
34.08
37.90
16
20
20
22
26
30
33
36
39
43
22
22
22
22
22
28
28
28
28
28
6
6
6
6
6
AL28AT3/48-0
AL28AT3/60-0
AL28AT3/72-0
6
6
6
48
60
72
45.84
57.30
68.75
54.54
57.00
68.45
34
38
50
22
22
22
28
28
28
6
6
6
Weight
13
10
5.0
16
25
32
Length
mm
No. of
Teeth
Belt No
Length
mm
No. of
Teeth
1.5
2.7
50
2.5
AT5
0.034kg/m
45
51
52
56
60
AT5/660
AT5/710
AT5/720
AT5/750
AT5/780
660
710
720
750
780
132
142
144
150
156
AT5/330
AT5/340
AT5/375
AT5/390
AT5/420
330
340
375
390
420
66
68
75
78
84
AT5/825
AT5/860
AT5/900
AT5/920
AT5/975
825
860
900
920
975
165
172
180
184
195
AT5/450
AT5/455
AT5/480
AT5/500
AT5/525
450
455
480
500
525
90
91
96
100
105
AT5/1050
AT5/1125
AT5/1230
AT5/1500
AT5/1750
1050
1125
1230
1500
1750
210
225
246
300
350
AT5/545
AT5/600
AT5/610
AT5/620
AT5/630
545
600
610
620
630
109
120
122
124
126
AT5/2000
AT5/3350
AT5/3800
2000
3350
3800
400
670
760
3.2
225
255
260
280
300
Breco-M
Breco- V
41.8
5.5
AT5/225
AT5/255
AT5/260
AT5/280
AT5/300
25
10
16
25
32
50
Synchroflex
350
700
1260
2030
2660
4200
Breco- M
700
1120
1820
2240
3500
Breco- V
350
560
910
1120
1750
Brecoflex
700
1260
2030
2660
4200
8.2
AT5-Clamp Plate
Code No
Part No
Belt Width "A" Clamp Width "B"
270716 16AT5-Clamp
16mm
35mm
270725 25AT5-Clamp
25mm
44mm
270732 32AT5-Clamp
32mm
51mm
14
Width (mm)
Dm
Df
Pcd
Od
d
Type
teeth
AL27AT5/12-2
AL27AT5/14-2
AL27AT5/15-2
AL27AT5/16-2
AL27AT5/18-2
6F
6F
6F
6F
6F
12
14
15
16
18
AL27AT5/19-2
AL27AT5/20-2
AL27AT5/22-2
AL27AT5/24-2
AL27AT5/25-2
6F
6F
6F
6F
6F
AL27AT5/26-2
AL27AT5/27-2
AL27AT5/28-2
AL27AT5/30-2
AL27AT5/32-2
AL27AT5/36-2
AL27AT5/40-2
AL27AT5/44-0
AL27AT5/48-0
AL27AT5/60-0
Pcd
Od
Dm
Df
Weight
19.10
22.29
23.88
25.47
28.65
17.85
21.05
22.65
24.20
27.40
11
14
16
18
20
23.0
25.0
28.0
32.0
32.0
21
21
21
21
21
27
27
27
27
27
6
6
0.022
0.026
0.029
0.035
0.043
19
20
22
24
25
30.25
31.83
35.02
38.21
39.80
29.00
30.60
33.75
36.95
38.55
22
23
24
26
26
36.0
36.0
38.0
42.0
44.0
21
21
21
21
21
27
27
27
27
27
6
6
6
6
6
0.049
0.053
0.054
0.076
0.081
6F
6F
6F
6F
6F
26
27
28
30
32
41.39
42.98
44.58
47.76
50.94
40.15
41.75
43.35
46.5
49.70
26
30
32
34
38
44.0
48.0
48.0
51.0
54.0
21
21
21
21
21
27
27
27
27
27
6
6
8
8
8
0.085
0.090
0.092
0.105
0.123
6F
6F
6
6
6
36
40
44
48
60
57.31
63.66
70.05
76.42
95.52
56.05
62.45
68.80
75.15
94.25
38
40
45
50
65
63.0
66.0
-
21
21
21
21
21
27
27
27
27
27
8
8
8
8
8
0.160
0.193
0.280
0.280
0.430
Type
teeth
Od
Dm
Df
Weight
AL38AT5/12-2
AL38AT5/14-2
AL38AT5/15-2
AL38AT5/16-2
AL38AT5/18-2
6F
6F
6F
6F
6F
12
14
15
16
18
19.10
22.29
23.88
25.47
28.65
17.85
21.05
22.65
24.20
27.40
11
14
16
18
20
23.0
25.0
28.0
32.0
32.0
32
32
32
32
32
38
38
38
38
38
6
6
0.031
0.037
0.041
0.041
0.050
AL38AT5/19-2
AL38AT5/20-2
AL38AT5/22-2
AL38AT5/24-2
AL38AT5/25-2
6F
6F
6F
6F
6F
19
20
22
24
25
30.25
31.83
35.02
38.21
39.80
29.00
30.60
33.75
36.95
38.55
22
23
24
26
26
36.0
36.0
38.0
42.0
44.0
32
32
32
32
32
38
38
38
38
38
6
6
6
6
6
0.070
0.076
0.078
0.109
0.116
AL38AT5/26-2
AL38AT5/27-2
AL38AT5/28-2
AL38AT5/30-2
AL38AT5/32-2
6F
6F
6F
6F
6F
26
27
28
30
32
41.39
42.98
44.58
47.76
50.94
40.15
41.75
43.35
46.50
49.70
26
30
32
34
38
44.0
48.0
48.0
51.0
54.0
32
32
32
32
32
38
38
38
38
38
6
6
8
8
8
0.120
0.128
0.136
0.160
0.176
AL38AT5/36-2
AL38AT5/40-2
AL38AT5/44-0
AL38AT5/48-0
AL38AT5/60-0
6F
6F
6
6
6
36
40
44
48
60
57.31
63.66
70.05
76.42
95.52
56.05
62.45
68.80
75.15
94.25
38
40
45
50
65
63.0
66.0
-
32
32
32
32
32
38
38
38
38
38
8
8
8
8
8
0.230
0.276
0.349
0.400
0.624
Type 6
Pcd
Dm
Pcd
Od
d
Pulley No.
Pulley No.
Type
teeth
Od
Dm
Df
Weight
AL46AT5/12-2
AL46AT5/14-2
AL46AT5/15-2
AL46AT5/16-2
AL46AT5/18-2
6F
6F
6F
6F
6F
12
14
15
16
18
19.10
22.29
23.88
25.47
28.65
Pcd
17.85
21.05
22.65
24.20
27.40
11
14
16
18
20
23.0
25.0
28.0
32.0
32.0
40
40
40
40
40
46
46
46
46
46
6
6
0.038
0.045
0.050
0.060
0.074
AL46AT5/19-2
AL46AT5/20-2
AL46AT5/22-2
AL46AT5/24-2
AL46AT5/25-2
6F
6F
6F
6F
6F
19
20
22
24
25
30.25
31.83
35.02
38.21
39.80
29.00
30.60
33.75
36.95
38.55
22
23
24
26
26
36.0
36.0
38.0
42.0
44.0
40
40
40
40
40
46
46
46
46
46
6
6
6
6
6
0.084
0.083
0.096
0.117
0.127
AL46AT5/26-2
AL46AT5/27-2
AL46AT5/28-2
AL46AT5/30-2
AL46AT5/32-2
6F
6F
6F
6F
6F
26
27
28
30
32
41.39
42.98
44.58
47.76
50.94
40.15
41.75
43.35
46.50
49.70
26
30
32
34
38
44.0
48.0
48.0
51.0
54.0
40
40
40
40
40
46
46
46
46
46
6
6
8
8
8
0.145
0.154
0.157
0.193
0.217
AL46AT5/36-2
AL46AT5/40-2
AL46AT5/44-0
AL46AT5/48-0
AL46AT5/60-0
6F
6F
6
6
6
36
40
44
48
60
57.31
63.66
70.05
76.42
95.52
56.05
62.45
68.80
75.15
94.25
38
40
45
50
65
63.0
66.0
-
40
40
40
40
40
46
46
46
46
46
8
8
8
8
8
0.280
0.329
0.478
0.510
0.774
15
10.0
2.5
5.0
50
5.0
Belt weight
25
AT10
0.063kg/m
32
50
75
100
Length
mm
No. of
Teeth
Belt No
Length
mm
No. of
Teeth
AT10/500
AT10/560
AT10/580
AT10/600
AT10/610
500
560
580
600
610
50
56
58
60
61
AT10/1100
AT10/1150
AT10/1200
AT10/1210
AT10/1250
1100
1150
1200
1210
1250
110
115
120
121
125
AT10/660
AT10/700
AT10/730
AT10/780
AT10/800
660
700
730
780
800
66
70
73
78
80
AT10/1280
AT10/1300
AT10/1320
AT10/1350
AT10/1360
1280
1300
1320
1350
1360
128
130
132
135
136
AT10/840
AT10/880
AT10/890
AT10/920
AT10/960
840
880
890
920
960
84
88
89
92
96
AT10/1400
AT10/1480
AT10/1500
AT10/1600
AT10/1700
1400
1480
1500
1600
1700
140
148
150
160
170
AT10/980
AT10/1000
AT10/1010
AT10/1050
AT10/1080
980
1000
1010
1050
1080
98
100
101
105
108
AT10/1720
AT10/1800
AT10/1860
AT10/1940
1720
1800
1860
1940
172
180
186
194
Breco-M
Breco- V
16
Width (mm)
16
25
32
50
75
100
Synchroflex
2000
3500
4750
7750
12000 16000
Breco- M
4250
5500
8500
12750 17000
Breco- V
2125
2750
4250
6375
Brecoflex
3500
4750
7750
12000 16000
8500
L
F
Pcd
Od
Dm
Df
Weight
6F
6F
6F
6F
6F
15
16
18
19
20
47.75
50.93
57.29
60.48
63.66
45.90
49.10
55.45
58.65
61.80
32
35
40
44
46
51
54
60
66
66
32
32
32
32
32
42
42
42
42
42
8
8
8
8
8
0.152
0.176
0.224
0.247
0.276
AL42AT10/22-2
AL42AT10/24-2
AL42AT10/25-2
AL42AT10/26-2
AL42AT10/27-2
6F
6F
6F
6F
6F
22
24
25
26
27
70.03
76.39
79.58
82.76
85.95
68.20
74.55
77.75
80.90
84.10
52
58
60
60
60
75
83
83
87
91
32
32
32
32
32
42
42
42
42
42
8
8
8
8
8
0.337
0.392
0.422
0.477
0.536
AL42AT10/28-2
AL42AT10/30-2
AL42AT10/32-2
AL42AT10/36-2
AL42AT10/40-2
6F
6F
6F
6F
6F
28
30
32
36
40
89.12
95.49
101.86
114.59
127.32
87.25
93.65
100.00
112.75
125.45
60
60
65
70
80
93
97
106
119
131
32
32
32
32
32
42
42
42
42
42
8
8
10
10
10
0.540
0.640
0.693
0.873
1.067
AL42AT10/44-0
AL42AT10/48-0
AL42AT10/60-0
6
6
6
44
48
60
140.05
152.78
190.98
138.20
150.95
189.15
88
95
110
32
32
32
42
42
42
10
16
16
1.350
1.516
2.339
Type 6F
teeth
AL42AT10/15-2
AL42AT10/16-2
AL42AT10/18-2
AL42AT10/19-2
AL42AT10/20-2
Dm
Df
Pcd
Od
d
Type
Dm
Df
Weight
AL50AT10/15-2
AL50AT10/16-2
AL50AT10/18-2
AL50AT10/19-2
AL50AT10/20-2
Type
6F
6F
6F
6F
6F
teeth
15
16
18
19
20
47.75
50.93
57.29
60.48
63.66
Pcd
45.90
49.10
55.45
58.65
61.80
Od
32
35
40
44
46
51
54
60
66
66
40
40
40
40
40
50
50
50
50
50
6
8
8
8
8
0.253
0.286
0.322
AL50AT10/22-2
AL50AT10/24-2
AL50AT10/25-2
AL50AT10/26-2
AL50AT10/27-2
6F
6F
6F
6F
6F
22
24
25
26
27
70.03
76.39
79.58
82.76
85.95
68.20
74.55
77.75
80.90
84.10
52
58
60
60
60
75
83
83
87
91
40
40
40
40
40
50
50
50
50
50
8
8
8
8
8
0.393
0.475
0.527
0.564
0.602
AL50AT10/28-2
AL50AT10/30-2
AL50AT10/32-2
AL50AT10/36-2
AL50AT10/40-2
6F
6F
6F
6F
6F
28
30
32
36
40
89.12
95.49
101.86
114.59
127.32
87.25
93.65
100.00
112.75
125.45
60
60
65
70
80
93
97
106
119
131
40
40
40
40
40
50
50
50
50
50
8
8
10
10
10
0.642
0.740
0.844
1.063
1.317
AL50AT10/44-0
AL50AT10/48-0
AL50AT10/60-0
6
6
6
44
48
60
140.05
152.78
190.98
138.20
150.95
189.15
88
95
110
40
40
40
50
50
50
10
16
16
1.611
1.931
3.004
Dm
Pcd
Od
d
Type 6
Dm
Df
Weight
AL70AT10/15-2
AL70AT10/16-2
AL70AT10/18-2
AL70AT10/19-2
AL70AT10/20-2
Pulley No.
Type
6F
6F
6F
6F
6F
teeth
15
16
18
19
20
47.75
50.93
57.29
60.48
63.66
Pcd
45.90
49.10
55.45
58.65
61.80
Od
32
35
40
44
46
51
54
60
66
66
60
60
60
60
60
70
70
70
70
70
12
12
12
0.422
0.466
0.520
AL70AT10/22-2
AL70AT10/24-2
AL70AT10/25-2
AL70AT10/26-2
AL70AT10/27-2
6F
6F
6F
6F
6F
22
24
25
26
27
70.03
76.39
79.58
82.76
85.95
68.20
74.55
77.75
80.90
84.10
52
58
60
60
60
75
83
83
87
91
60
60
60
60
60
70
70
70
70
70
12
12
12
12
12
0.570
0.736
0.766
0.816
0.946
AL70AT10/28-2
AL70AT10/30-2
AL70AT10/32-2
AL70AT10/36-2
AL70AT10/40-2
6F
6F
6F
6F
6F
28
30
32
36
40
89.12
95.49
101.86
114.59
127.32
87.25
93.65
100.00
112.75
125.45
60
60
65
70
80
93
97
106
119
131
60
60
60
60
60
70
70
70
70
70
12
12
12
12
12
0.960
1.169
1.300
1.637
1.999
AL70AT10/44-0
AL70AT10/48-0
AL70AT10/60-0
6
6
6
44
48
60
140.05
152.78
190.98
138.20
150.95
189.15
88
95
110
60
60
60
70
70
70
12
16
16
2.357
2.830
4.366
17
32
50
4.0
9.0
10.0
Belt weight
AT20
0.106 kg/m
100
Belt No
Length
mm
AT20/1000
AT20/1100
AT20/1200
AT20/1260
AT20/1500
1000
1100
1200
1260
1500
50
55
60
63
75
AT20/1600
AT20/1700
AT20/1760
AT20/1800
AT20/1900
1600
1700
1760
1800
1900
80
85
88
90
95
AT20/1960
1960
98
20.0
50
75
No. of
Teeth
Breco-M
Breco- V
Width (mm)
18
32
50
75
100
150
Synchroflex
6750
11250
17550
23850
36450
Breco- M
7200
11700
18000
25000
36000
Breco- V
3600
5800
9000
12500
18000
Brecoflex
6000
10000
15600
21200
32400
Dm
Df
Pcd
Od
d
Type
teeth
Pcd
Od
Dm
Df
AL53AT20/18-2
AL53AT20/20-2
AL53AT20/22-2
AL53AT20/24-2
AL53AT20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
38
38
38
38
38
53
53
53
53
53
15
15
15
15
15
AL53AT20/30-2
AL53AT20/32-2
AL53AT20/36-0
AL53AT20/40-0
AL53AT20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
38
38
38
38
38
53
53
53
53
53
15
18
18
20
20
AL53AT20/60-0
AL53AT20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
38
38
53
53
20
20
Weight
Type 6F
L
F
Type
teeth
Pcd
Od
Dm
Df
AL71AT20/18-2
AL71AT20/20-2
AL71AT20/22-2
AL71AT20/24-2
AL71AT20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
56
56
56
56
56
71
71
71
71
71
18
18
18
18
18
AL71AT20/30-2
AL71AT20/32-2
AL71AT20/36-0
AL71AT20/40-0
AL71AT20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
56
56
56
56
56
71
71
71
71
71
18
20
20
20
24
AL71AT20/60-0
AL71AT20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
56
56
71
71
24
24
Weight
Dm
Pcd
Od
d
Pulley No.
Type 6
Type
teeth
Pcd
Od
Dm
Df
AL96AT20/18-2
AL96AT20/20-2
AL96AT20/22-2
AL96AT20/24-2
AL96AT20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
81
81
81
81
81
96
96
96
96
96
24
24
24
24
24
AL96AT20/30-2
AL96AT20/32-2
AL96AT20/36-0
AL96AT20/40-0
AL96AT20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
81
81
81
81
81
96
96
96
96
96
24
32
32
32
32
AL96AT20/60-0
AL96AT20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
81
81
96
96
32
32
Weight
Pulley No.
Type
teeth
Pcd
Od
Dm
Df
Weight
Dm
Pcd
Od
d
Type 6W
AL123AT20/18-2
AL123AT20/20-2
AL123AT20/22-2
AL123AT20/24-2
AL123AT20/25-2
6F
6F
6F
6F
6F
18
20
22
24
25
114.59
127.32
140.05
152.78
159.15
111.75
124.45
137.20
149.95
156.30
80
90
90
95
95
119
138
146
160
168
108
108
108
108
108
123
123
123
123
123
24
24
24
24
24
AL123AT20/30-2
AL123AT20/32-2
AL123AT20/36-0
AL123AT20/40-0
AL123AT20/48-0
6F
6F
6
6
6
30
32
36
40
48
190.98
203.71
229.18
254.64
305.57
188.15
200.85
226.35
251.80
302.70
110
110
110
110
130
198
216
-
108
108
108
108
108
123
123
123
123
123
24
32
32
32
32
AL123AT20/60-0
AL123AT20/72-0
6
6
60
72
381.96
451.99
379.10
455.50
130
140
108
108
123
123
32
32
AT20 20mm Pitch pulleys are not available from stock and can be
19
manufactured to your personal requirements..
Linear Table
Minimum Diameters
REVERSE BENDING
NORMAL USE
Technical Information
(1)
(2)
ATL5
Z = 25
= 60
ATL10
Z = 25
= 150
ATL20
Z = 25
= 250
(1)
(2)
ATL5
Z = 25
= 40
ATL10
Z = 25
= 80
ATL20
Z = 25
= 160
ATL5
Belt Width
Allowable tensile load (N)
16
25
1300
32
2400
6
50
2600
6
4200
6
0.33 10
0.50 10
0.65 10
1.05 106
0.059
0.090
0.119
0.187
ATL10
Belt Width
32
50
75
100
7200
11200
16800
22400
1.8 106
2.8 106
4.2 106
5.6 106
0.22
0.34
0.51
0.68
32
50
75
100
ATL20
Belt Width
Allowable tensile load (N)
20
9800
15400
6
23800
6
31500
6
2.36 10
3.71 10
5.74 10
7.59 106
0.35
0.55
0.84
1.11
Angular Drives
Angular Drives
Synchroflex, Breco, & Brecoflex belts can be used in angular drives as a crossed
(twisted) drive but not as a radially displaced drive.
With crossed timing belt applications, the outer tension members suffer greater elongation
than the middle ones.
At a ratio of IT > 20b there is no power reduction and no special design considerations
need to be made.
If a ratio of IT < 20b is necessary, please contact our technical department.
IT > 20 b
b= Belt Width
IT= Span Length
Timing belts must be guided with flanges to eliminate the wandering off effect of side loads
and as a rule this is done with flanges.The correct design of the belt guiding system
incorporating the minimum of side loads and frictional losses is of fundamental importance
for a trouble free drive. The direction of rotation and the span length are of equal importance.
It is more cost effective to have flanges on the small pulley
rather than the large one.
21
6.35
9.53
12.7
19.1
25.4
38.1
50.8
76.2
101.6
Imperial Code
025
037
050
075
100
150
200
300
400
1.22
1.32
5.08
40
XL Single sided
Belt No.
Breco-M
Breco-V
XL025-M or -V
XL037-M or -V
XL050-M or -V
XL075-M or -V
XL100-M or -V
210
330
390
630
840
105
165
195
315
420
Weight
1.7
1.85
9.525
40
L Single sided
Belt No.
Breco-M
Breco-V
L037-M or -V
L050-M or -V
L075-M or -V
L100-M or -V
L150-M or -V
L200-M or -V
630
840
1260
1680
2520
3150
315
420
630
840
1260
1570
Weight
2.0
2.18
12.7
40
H Single sided
Belt No.
H050-M or -V
H075-M or -V
H100-M or -V
H150-M or -V
H200-M or -V
H300-M or -V
H400-M or -V
Weight
2.18
2.0
2.18
Belt No.
H100-DL-M or -V
H150-DL-M or -V
H200-DL-M or -V
H300-DL-M or -V
H400-DL-M or -V
Weight
4.85
6.22
Belt No.
XH Single sided
22
1000
1600
2000
3200
4200
5200
6600
500
800
1000
1600
2100
2600
3300
Breco-M
Breco-V
2000
3200
4200
5200
6600
1000
1600
2100
2600
3300
22.225
40
Breco-V
12.7
40
Breco-M
XH100-M or -V
XH150-M or -V
XH200-M or -V
XH300-M or -V
XH400-M or -V
Weight
Breco-M
Breco-V
3500
5250
7000
10500
14000
1750
2625
3500
5250
7000
25
32
50
Breco -V
2.5
10
3.5
100
50TK10(K6) /1600-V
Belt weight
75
The combination of steel reinforced belts with moulded or welded V belts produces accurate,
linear belts. They are unparalled for:
L
38
Type
teeth
Pcd
Od
AL 30TK10K6 /20
AL 30TK10K6 /24
AL 30TK10K6 /25
AL 30TK10K6 /27
AL 30TK10K6 /30
TK
TK
TK
TK
TK
20
24
25
27
30
63.66
76.39
79.58
85.94
95.49
61.80
74.55
77.75
84.10
93.65
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
30
30
30
30
30
12
12
12
12
12
AL 30TK10K6 /32
AL 30TK10K6 /36
AL 30TK10K6 /40
AL 30TK10K6 /48
AL 30TK10K6 /60
TK
TK
TK
TK
TK
32
36
40
48
60
101.86
114.59
127.32
152.79
190.99
100.00
112.75
125.45
150.95
189.15
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
30
30
30
30
30
12
16
16
16
16
Od
Pcd
Pulley No.
TK Type
Type
teeth
Pcd
Od
AL 37TK10K6 /20
AL 37TK10K6 /24
AL 37TK10K6 /25
AL 37TK10K6 /27
AL 37TK10K6 /30
TK
TK
TK
TK
TK
20
24
25
27
30
63.66
76.39
79.58
85.94
95.49
61.80
74.55
77.75
84.10
93.65
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
37
37
37
37
37
12
12
12
12
12
AL 37TK10K6 /32
AL 37TK10K6 /36
AL 37TK10K6 /40
AL 37TK10K6 /48
AL 37TK10K6 /60
TK
TK
TK
TK
TK
32
36
40
48
60
101.86
114.59
127.32
152.79
190.99
100.00
112.75
125.45
150.95
189.15
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
37
37
37
37
37
12
16
16
16
16
teeth
Pcd
Od
AL 55TK10K6 /20
AL 55TK10K6 /24
AL 55TK10K6 /25
AL 55TK10K6 /27
AL 55TK10K6 /30
Pulley No.
TK
TK
TK
TK
TK
20
24
25
27
30
63.66
76.39
79.58
85.94
95.49
61.80
74.55
77.75
84.10
93.65
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
55
55
55
55
55
12
12
12
12
12
AL 55TK10K6 /32
AL 55TK10K6 /36
AL 55TK10K6 /40
AL 55TK10K6 /48
AL 55TK10K6 /60
TK
TK
TK
TK
TK
32
36
40
48
60
101.86
114.59
127.32
152.79
190.99
100.00
112.75
125.45
150.95
189.15
6.5
6.5
6.5
6.5
6.5
5
5
5
5
5
55
55
55
55
55
12
16
16
16
16
23
Synchroflex and Breco belts can be supplied with special profiles on the back to offer designers infinite solutions
to conveying, handling, and postioning drives.
Profiles are thermally welded to the belt back according to customer requirements.
The standard pitch tolerance of profiles is 0.5mm.
Initial Design
Drive parameters must first be determined, thus establishing the belt pitch, length, and size
of pulleys. Profiles can be welded to any pitch belt.
For transport applications it is advisable to use Breco belts with PAZ nylon coating(see page
29). This coating gives a reduced frictional coefficient, thus better running and less wear
when used with support plates.
24
Choice of Profile
The type of product to be conveyed and the method of transportation will influence the
choice of profile.
Special profiles can be made from a new mould. There will be a tooling charge for this
service.
Profile Material
Polyurethane (92 shore). The same material used for the Breco/Brecoflex belts.
Positioning of Profile
The belt flexibility relies on the tooth gap. In order to maintain the belt flexibility around the
pulleys it is advisable to position the profiles over the belt teeth.
If possible the pitch of the profiles should be a multiple of the belt pitch. If this is not possible,
ensure that the sum of the profile pitches is equal to the belt length.
The standard pitch to pitch tolerance between profiles is 0.5mm. Standard height tolerance
is -0.5mm.
Ordering Example
Flash
Flash occurs between the belt back and the profile as a result of the welding process. The
flash radius can be between 0.5 and 2mm depending on the profile size and thickness.
If the flash will impair the function of the profile, please order with flash removed
25
The belt flexibility can be affected by the profile thickness. As a rule the thickness should be
as small as possible. The following table represents the relationship between profile
thickness and the chosen pulley size.
Max. thickness in mm - profile over tooth form
Max. thickness in mm - (profile over tooth gap)
Number of teeth in pulley
20
25
30
40
50
60
100
T5
5 (2)
6 (2)
6 (3)
8 (4)
9 (6)
10 (8)
12 (10)
T10
8 (3)
9 (4)
10 (4)
12 (6)
14 (9)
15 (12)
20 (20)
T20
12 (5)
13 (5)
15 (6)
18 (8)
20 (12)
23 (20)
30 (30)
AT5
5 (2)
6 (2)
6 (3)
8 (4)
9 (6)
10 (8)
12 (10)
AT10
8 (3)
9 (4)
10 (4)
12 (6)
14 (9)
15 (12)
20 (20)
AT20
12 (5)
13 (5)
15 (6)
18 (8)
20 (12)
23 (20)
30 (30)
XL
5 (2)
6 (2)
6 (3)
8 (4)
9 (6)
10 (8)
12 (10)
6 (3)
7 (3)
8 (4)
10 (5)
12 (7)
13 (10)
16 (16)
8 (4)
9 (5)
10 (6)
12 (7)
14 (10)
15 (12)
20 (20)
Pitch
13 (5)
14 (5)
15 (6)
18 (8)
20 (12)
23 (20)
30 (30)
XH
Example for determining the profile thickness on a T10 belt running around a 20 tooth
pulley.
26
The flexibilty of the belt will not be affected if reliefs are designed into the
profile.
Profiles in pairs are preferred for transporting when positioning or depositing is required.
Standard tolerance between profile pairs 0.5mm.
A tolerance of 0.2mm is attainable using special tooling. There is a tooling charge for this
service.
Holes can be drilled into profiles to suit special applications. Standard tolerances as below.
NB. The profiles are drilled before they are welded to the belt.
For special applications profiles can be manufactured with moulded inserts. Standard inserts
can be drilled, tapped, and threaded in a wide variety of sizes.
27
28
Special Belts
Gen III
Arrangment of bifilar
steel cord tension
members
E Tension members
The thinner the individual wire the greater the flexibility of the belt. With E tension members
the reduced cross section allows more individual wires and therefore reduces the tensile
stress in the tension member. The advantage of E tension members is a reduction in
minimum pulley and idler diameters for reverse bending drives, due to the better fatigue
strength. The smallest pulley diameter can be reduced by up to 30% over standard tension
members. Belts with E tension members are recommended for multi-shaft drives with
severe reverse bending (contraflexure).
Available Pitches: AT3, AT5, AT10, AT20, T5, T10, T20
Summary.
Longer life
Drive Type
Without Contraflexure
Min. No. Teeth
Min. Idler mm
With Contraflexure
Min. No. Teeth
Min. Idler mm
Kevlar Tension
Members
T5
T10
T20
AT3
AT5
AT10
10
18
10
50
12
80
15
20
12
18
12
50
12
18
15
50
20
120
20
20
20
50
20
80
Synchroflex, Breco, and Brecoflex belts are also available with Kevlar tension members.
29
ATN Belts
Timing belts with Integrated Profile
ATN has been devised specifically for use in conveyor technology. The exchangeable profile attachment in the belt tooth allows for
a rapid assembly and changing of profiles. As such, using the same timing belts on a conveyor, equipped with different
atachments , different goods can be transported as needed.
Profiles are produced individually to suit each conveyor application.
FDA approved polyurethane also available on request.
Available Inserts
Material
Plastic
Polymide
Brass
MS 58F 36
Areas of Use
Normal temperatures
Brass
Low Temperatures
Plastic
Convincing Benefits:
Convincing Benefits:
Part No.
Standard
ATN10
ATN
ATN12.7
ATN
12.7
20
50
75
100
ATN20
ATN
20
20
50
75
100
ATN
10
25
50
75
100
ATN
12.7
20
50
75
100
ATN12.7 K6
Profile
Pitch
(mm)
10
30
V-guide
bK
-
Min. Teeth
on Pulley
25
Coating
PAR
PAZ
ATN Belts
Timing belts with Integrated Profile
Breco-V
25ATN10
50ATN10
75ATN10
100ATN10
3000
6000
9000
12000
1000
2000
3000
4000
25ATN12.7
50ATN12.7
75ATN12.7
100ATN12.7
3000
6000
9000
12000
1000
2000
3000
4000
25ATN20
50ATN20
75ATN20
100ATN20
8000
12000
16000
2700
4000
5400
100
1500
1500
-
31
The use of timing belts will always lead to static emissions being generated by the two
moving surfaces of the pulley and belt.
A special conductive coating can be applied to polyurethane belts for when static electricity is
undesirable. Problems that may arise from static discharge are:
Risks of shock to the operator from high voltages which can be generated.
Properties of Anti-static belt
Black in colour.
A nylon fabric coating extruded during manufacture, can give a reduced coefficient of friction,
facilitating easier meshing with the pulleys and a reduction in noise. This coating is ideal for
transport applications when suppport plates or guide rails are used.
Availability
Accumulation Conveyor
Any length up to 50M possible.
A: Nylon facing on belt back and teeth. PAZ-PAR
B: Support plate.
32
Haul-Off Belt
A: Nylon facing on tooth side; PAZ = Low friction
B: Back of belt with transport backing. = High friction
C: Pressure plates
Polyurethane
Transparent
85 shore A
80C
2mm
80mm
Simple oils and fats
Highest wear resistance
Transport of mechanically aggresive parts
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Polyurethane
Transparent
85 shore A
80C
4mm
120mm
Simple oils and fats
Tip contact with product to be transported
Transport with oil contact
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Polyurethane
Transparent
85 shore A
80C
4mm
120mm
Simple oils and fats
Linear contact with product to be transported
Transport with oil contact
NP385
FG 385
PUR 385
Material
Colour
Hardness
Polyurethane
Transparent
85 shore A
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
80C
3mm
4mm
5mm
6mm
80mm
120mm
150mm
180mm
Petrol, ozone, and simple oils and fats
Highest wear resistance, high coefficient of friction
Transport of parts showing a coarse surface or burrs
Material
Colour
Density (g/dm3)
FKM
Blue
220
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
80C
3 to 25
3 to 25
3 to 25
80 to 120
80 to 120
80 to 120
Some oils and fats
Good wear resistance
Transport of lightweight parts
Sylomer
Green
380
Brown
400
33
Polyurethane
Yellow
Approx. 60 shore A
60C
2mm
3mm
4mm
5mm
60mm
60mm
80mm
100mm
Simple oils and fats
Good wear resistance
Vacuum transport belts subject to high loads.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
PVC
Green or Blue
Approx. 30 shore A
60C
4mm
60mm
Green: Steadily against simple oils and fats (Blue: Not oil resistant)
High wear resistance, high coefficient of friction
Well suited to inclined conveying.
Material
Colour
Density
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Celular rubber
Black
190 g/dm3
60C
2mm
3mm
5mm
30mm
40mm
60mm
Limited against simple oils and fats
Soft foam quality
Transport of sensitive parts.
Supergrip
Porol
Celloflex
Material
Colour
Density
PU foam
Brown
350g/dm3
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
80C
2mm
3mm
5mm
40mm
40mm
40mm
Limited against simple oils and fats
Highly flexible
Transport of sensitive parts.
Material
Colour
Hardness
Polyurethane
Transparent
Approx. 80 shore A
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
80C
1mm
60mm
Some cleaning agents.
Good wear resistance
Foodstuff industry.
HV1-Film
34
Leather
Grey-blue
60C
2mm
80mm
100mm
Simple oils and fats
Good friction, good abrasiveness.
Applications
Material
Colour
Hardness
Temp. Resistance
Available Thickness
FKM mix
Black
Approx. 75 shore A
max. 200C (coating only)
2mm
80mm
High heat resistance
Simple oils and fats, high heat resistance
Short time transport of parts having high residual heat.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Gum rubber
Brown
Approx. 35 - 40 shore A
Up to Approx. 70C
6mm
10mm
80mm
120mm
Limited against oils and fats
Wear resistant, good carrying quality
General transport
3mm
Viton
Correx
Linatex
Material
Colour
Hardness
Natural rubber
Red
Approx. 40 shore A
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Up to Approx. 60C
1.6mm
2.4mm
3.2mm
4.8mm
25mm
30mm
40mm
40mm
Some oils
High wear resistance, resistant to rupture
Transport and haul-off belts subject to high friction.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Polyurethane
Transparent/yellow
70 shore A
80C
2-5mm
60mm
Simple oils and fats
Good wear resistance
General transport tasks
6.4mm
40mm
12.7mm
60mm
20mm
80mm
Polythan D44
35
PVC
White
Approx. 40 shore A
80C
2mm
3mm
4mm
5mm
60mm
60mm
80mm
80mm
Limited against oils and fats
FDA approved for contact with foodstuff.
Foodstuff industry.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
PVC
White
Approx. 40 shore A
80C
4mm
80mm
Limited against oils and fats
FDA approved for contact with foodstuff.
Foodstuff industry.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
PVC
Blue
Approx. 40 shore A
80C
1mm
2mm
30mm
30mm
Limited against oils and fats
High coefficient of friction
Transport of paper, film and, wood
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
PVC
Green
Approx. 40 shore A
80C
1mm
30mm
Limited against oils and fats
High coefficient of friction.
Transport of parts implying contact with oil.
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
6mm
120mm
PVC Herringbone
PVC Blue
PVC Minigrip
Composite Coating
36
Linatrile
Vulcanisate based on nitrile
Orange
55 shore A
-20C to + 110C
3-35mm
Depends on density selected
Oil, grease, and other chemicals
Good resistance to abrasion, ageing, and fatigue
Drawing-off bands in textile industry, transportation of matter containing parrafin
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Polyester fleece
Black
80C
2mm
120mm
Oils and grease
Electrostatic properties
Glass industry as transport belt in hot environment
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
RP 400
Rubber
Yellow
35 shore A
- 10C to + 80C
2mm
3mm
4mm
5mm
6mm
30mm
40mm
40mm
60mm
60mm
Oils and grease under most conditions
Very high wear resistance
Glass and steel industry, abrasive material to size 40mm
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Material
Colour
Hardness
Temp. Resistance
Available Thickness
Min. Pulley Dia.
Resistances
Characteristics
Applications
Composite Coating
eg. PUR/silicone
White
60/50 shore A
Depends on materials used, silicone short term +180C
2.4mm
60mm
In accordance with materials used.
Anti sticking
Light transportation, air filter, textile and wood industries
TT 60
NBR
37
Reworked Belts
Synchroflex, Breco, and Brecoflex belts can be mechanically reworked for special applications in handling and transportation.
Belts with a thicker back are especially suited for reworking. Please not that belt flexibilty is greatly reduced with a thicker backed
belt. Cross grooves can be ground into belt to help improve flexibilty.
Back Cross Milling
Back cross milling enhances belt flexibilty. Milled grooves are used to improve safe loading and secure
positioning of the products on the belts.
Back Grinding
The backs of all Brecoflex timing belts are ground. For reasons of precision or in order to obtain a
roughened surface, all other timing belts of the Synchroflex and Breco delivery range can be ground. Here
the overall thickness x must not fall below a minimum thickness, otherwise the tension members could be
damaged.
38
Formulae
Center Distance
Acceleration Torque
Acceleration Time
Bore
Density
Torque
Rpm
Outside Diameter
Power
Moment of Inertia
Belt Length
Ratio
a
MB
tB
d
r
MB
n
dK
P
J
LB
i
(mm)
(Nm)
(s)
(mm)
(kg/dm3)
(Nm)
(min-1)
(mm)
(kW)
(kgm2)
(mm)
LB
Peripheral force
Torque
2 10 3 M
dO
19 .1 10 6 P
=
n dO
10 3 P
=
v
dO FU
2 103
9.55 103 P
=
n
dO P
=
2v
(N)
(mm)
(mm)
(m/s)
(N)
(s-1)
(mm)
(Z 2 + Z 1 ) + 2 a + 1 (Z 2 Z 1 )t
2
4a
FU =
Fzul
B
t
v
Fu
w
do
z1
Z1
ZB
Ze
LB = 2a + d O
LB = 2a + z t
Power
M =
J = 98 . 2 10 15 B d K d 4
P=
M n
9.55 103
FU d O n
19.1 106
F v
= U 3
10
Angular velocity
n
30
Velocity
v=
dO n
19 .1 10 3
dO =
Z t
Rpm
v=
19.1 103 v
dO
Acceleration torque
MB =
J n
9.55 t B
Only the units listed above should be used in the formulae as they are the approved SI units. The unit of force, the Newton, is
very important: 1 N is the force required to accelerate a body with a mass of 1 kg to 1 m/s2. 1 N = kg 1 m/s2
Force
Torque
Power
Centrifugal force
39
Idler Pulleys
Idler pulleys type B run on two deep groove roller bearings. The bearings are lubricated and sealed for life. Normal operating
temperatures up to 70C without reduction in life and temporary peak temperatures up to 120C are allowable. The shafts are made
from steel and the rollers and flanges are aluminium.
Part
Type
B 34/32-0
B 34/32-2
B 40/60-0
B 40/60-2
B 64/60-0
B 64/60-2
B 40/80-0
B 40/80-2
B 64/80-0
B 64/80-2
B 70/120-0
B 70/120-2
B 114/60-0
B 114/60-2
B 114/80-0
B 114/80-2
B 117/120-0
B 117/120-2
B 117/180-0
B 117/180-2
B/E0
B/E2
B/E0
B/E2
B/E0
B/E2
B/E0
B/E2
B/E0
B/E2
B/E0
B/E2
B/F0
B/F2
B/F0
B/F2
B/F0
B/F2
B/F0
B/F2
Part
AL 34T5/22-0
AL 34AT5/22-0
AL 40T10/20-0
AL 40AT10/20-0
AL 64T10/20-0
AL 64AT10/20-0
40
Max. belt
Width (mm)
25
25
32
32
40
40
32
32
50
50
50
50
100
100
100
100
100
100
100
100
Type
B/E0
B/E0
B/E0
B/E0
B/E0
B/E0
dB
B2
SW
34
34
40
40
64
64
40
40
64
64
70
70
114
114
114
114
117
117
117
117
32
32
60
60
60
60
80
80
80
80
120
120
60
60
80
80
120
120
180
180
41.5
71
71
91
91
137
71
91
137
204
42
42
50
50
74
74
50
50
74
74
85
85
124
124
124
124
131
131
131
131
5
5
5
5
5
5
5
5
5
5
5
5
-
34
34
34
34
65
65
80
80
M6
M6
M12
M12
M12
M12
M12
M12
M12
M12
M20
M20
M8 (3x)
M8 (3x)
M8 (3x)
M8 (3x)
M12 (3x)
M12 (3x)
M20 (3x)
M20 (3x)
10
10
20
20
20
20
20
20
20
20
30
30
15
15
15
15
24
24
25
25
17
17
27
27
27
27
27
27
27
27
36
36
-
dK
B2
SW
D1
34
34
40
40
64
64
34.15
33.79
61.80
61.84
61.80
61.84
42
42
50
50
74
74
5
5
5
5
5
5
M6
M6
M12
M12
M12
M12
10
10
20
20
20
20
17
17
27
27
27
27
20
20
30
30
30
30
Max. belt
Width (mm)
25
25
32
32
50
50
D1
Load Ratings
Cdyn.
Cstat.
20
7950 3920
20
7950 3920
30 19300 13100
30 19300 13100
30 19300 13100
30 19300 13100
30 19300 13100
30 19300 13100
30 19300 13100
30 19300 13100
45 70500 48000
45 70500 48000
45 19300 13100
45 19300 13100
45 19300 13100
45 19300 13100
85 70500 48000
85 70500 48000
106 106000 76000
106 106000 76000
Load Ratings
Cdyn.
Cstat.
7950
3920
7950
3920
19300
13100
19300
13100
19300
13100
19300
13100
Max.
RPM
30000
30000
15000
15000
15000
15000
15000
15000
15000
15000
7500
7500
15000
15000
15000
15000
7500
7500
6300
6300
Max.
RPM
30000
30000
15000
15000
15000
15000
Idler Pulleys
The MULCO tension roller Type M is an innovative development. It is available in 7 standard sizes. The tension rollers are
distinguished by a rigid, vibration-resistant load bearing design. The forces acting by the belt pull are reliably absorbed by the
generously dimensioned D1 base diameter. The ball race and the load bearing structure are made of AlCuMgPb (F38). The tension
rollers are over-mounted on the machine wall. The eccentrical fitting results in an easy adjustment of the belt pre-tension force. To
ensure the swivel motion around the mounting axle, the face spanner (pictured below) can be used.
The MULCO tension rollers are fitted with high quality grooved ball bearings. The first filling of the bearings consists of a highperformance lithium saponified grease to ensure life time service. The greases are short-time temperature resistant up to 120C.
Permanent temperatures of 70C and above will lead to a reduced useful life of the grease. The stated load bearing parameters
refer to the entire tension roller on the basis of a centred belt load.
Type 1
Type 2
Weight
Part
BSR 71-100
Dimensions
Type
B1
B2
D1
Load Ratings
Max.
Cstat
(N)
1710
RPM
Recommended Applications
BSR 71100
0.06
14
16
23
28
18
Cdyn
(N)
4050
BSR 73100
0.10
27
26
40
28
18
6200
3450
15000
25
T2.5/T5
T2.5/T5/AT5
M 40/ 60-0
0.40
40
26
46
60
46
37.5
35
11
11200
5600
15000
32
AT5/T10
AT10/T10
M 60/ 60-0
0.50
60
36
66
60
46
57.5
35
11
19300
11200 15000
50
AT5/T10
AT10/T10
M 110/ 60-0
0.80
110
61
116
60
46
107
35
13
19300
11200 15000
100
AT5/T10
AT10/T10
M 60/ 120-0
2.40
60
35
70
120
94
57.5
17
70
17
51000
36600
6700
50
AT10/T20
AT20
M 110/ 120-0
3.90
110
60
120 120
94
108
17
70
17
51000
36600
6700
100
AT10/T20
AT20
M 85/ 180-0
7.00
85
45
30
70
26
100000 78000
4800
75
AT20
T20
M 160/ 180-0
10.80
160
83
30
70
26
100000 78000
4800
150
AT20
T20
Part
Kg
BSR 73-100
95
Strength
Torque
BSR 71100
M6
8.8
10
BSR 73100
M6
8.8
10
49
M 40/ 60-0
M10
8.8
M 60/ 60-0
M10
10.9
69
M 110/ 60-0
M12
12.9
145
M 60/ 120-0
M16
8.8
210
M 110/ 120-0
M16
12.9
355
M 85/ 180-0
M24
8.8
710
M 160/ 180-0
M24
12.9
1200
154
Cheese-head screws
according to DIN 6912 can be
used for machine wall mounting.
The appropriate screw length
depends on the fitting situation
and the surrounding structure.
The table shows thread sizes
and the recommended strength
of the cheese-head screws.
Max.
BeltWidth
8000
10
Minimum Idler mm
T2
M
T2.5
T5
T10
T20
AT3
AT5
AT10
AT20
On Belt
Back
T2.5/T5
On Teeth
T2.5/T5/AT5
41
Slider Beds
Slider beds are available as a standard range, matched to the timing belt width. The preferred delivery length is 2000 mm. Cuts to
length shorter than 2000 mm are available. The material ia UHMW polyethylene. This material has a low friction coefficient and is
also wear resistant. The sliding friction value between standard polyurethane and low-pressure polyethylene is ~ 0.3.
The C profile is made of zinc plated sheet steel. The cut out is intended for fastening screws. The C profile has no bore holes.
Due to the relatively large expansion of the sliding material under temperature, provide expansion gaps on the rail stucture.
Approximate formula for the linear expansion is 2mm/10C temperature difference over 1000 mm of length.
Slider Beds Without Edge Guide
Slider beds without edge guiding can be used with all our polyurethane timing belts. They
are recommended for all conveying applications with minimal side loads.
Part Numbers
Type G
G 32
G 50
G 75
G 100
B
mm
45
68
93
118
Type GC
GC 32
GC 50
GC 75
GC 100
BC
mm
50
75
100
125
K
mm
22
32
32
32
G
mm
23.5
34.5
34.5
34.5
N
T
mm mm
11
7
14
9
14
9
14
9
Recommended
ForBelt Width
32mm
50mm/2"
75mm/3"
100mm/4"
Part Numbers
F 32 x 2
F 50 x 2
F 75 x 2
F 100 x 2
F 32 x 4
F 50 x 4
F 75 x 4
F 100 x 4
F 50 x 7
F 75 x 7
F 100 x 7
FC 32 x 2
FC 50 x 2
FC 75 x 2
FC 100 x 2
FC 32 x 4
FC 50 x 4
FC 75 x 4
FC 100 x 4
FC 50 x 7
FC 75 x 7
FC 100 x 7
B
mm
45
68
93
118
45
68
93
118
68
93
118
BC
mm
50
75
100
125
50
75
100
125
75
100
125
bL
mm
33
51
76
101
33
51
76
101
51
76
101
K
mm
22
32
32
32
22
32
32
32
32
32
32
h
mm
2
2
2
2
4
4
4
4
7
7
7
G
mm
23.5
34.5
34.5
34.5
23.5
34.5
34.5
34.5
34.5
34.5
34.5
G
mm
23.5
34.5
23.5
34.5
34.5
34.5
34.5
34.5
34.5
N
mm
11
14
11
14
14
14
14
14
14
N
T
mm mm
11
7
14
9
14
9
14
9
11
7
14
9
14
9
14
9
14
9
14
9
14
9
Recommended
For Belt Width
32AT5
32T5
50AT5
50T5
75AT5
75T5
100AT5
100T5
32AT10
32T10
50AT10
50T10
75AT10
75T10
100AT10
100T10
50AT20
50T20
75AT20
75T20
100AT20
100T20
Part Numbers
42
K 32 x 4
K 50 x 4
K 32 x 4.5
K 50 x 4.5
K 75 x 4.5
K 100 x 4.5
K 50 x 2
K 75 x 2
K 100 x 2
KC 32 x 4
KC 50 x 4
KC 32 x 4.5
KC 50 x 4.5
KC 75 x 4.5
KC 100 x 4.5
KC 50 x 2
KC 75 x 2
KC 100 x 2
B
mm
45
68
45
68
93
118
68
93
118
BC
K
mm mm
50 22
75 32
50 22
75 32
100 32
125 32
75 32
100 32
125 32
h
mm
4
4
4.5
4.5
4.5
4.5
2
2
2
T
mm
7
9
7
9
9
9
9
9
9
Recommended
For Self Tracking Belts
32ATK5
32TK5
50ATK5
50TK5
32ATK10
32TK10
50ATK10
50TK10
75ATK10
75TK10
100ATK10
100TK10
50ATK20
50TK20
75ATK20
75TK20
100ATK20
100TK20
Tension Plates
Tension Plate Type L
Tension plates are used when you need to tension the belt at
the end connections. LE is the length of the belt which can be
clamped in the tension plate of length L.
Type L plates have slotted holes on top and bottom and are
made of aluminium.
Ordering Example 50 x 80 AT5 L
Order Code
50 x 80 AT5
50 x 80 T5
50 x 80 AT10
50 x 80 T10
50 x 130 AT20
50 x 130 T20
60 x 80 AT5
60 x 80 T5
60 x 80 AT10
60 x 80 T10
60 x 130 AT20
60 x 130 T20
75 x 80 AT5
75 x 80 T5
75 x 80 AT10
75 x 80 T10
75 x 130 AT20
75 x 130 T20
110 x 80 AT5
110 x 80 T5
110 x 80 AT10
110 x 80 T10
110 x 130 AT20
110 x 130 T20
140 x 80 AT5
140 x 80 T5
140 x 80 AT10
140 x 80 T10
140 x 130 AT20
140 x 130 T20
190 x 80 AT10
190 x 130 AT20
190 x 130 T20
50 x 80 T1/5 (XL)
50 x 80 T3/8 (L)
50 x 90 T1/2 (H)
63 x 80 T3/8 (L)
63 x 90 T1/2 (H)
75.5 x 80 T3/8 (L)
75.5 x 90 T1/2 (H)
101 x 90 T1/2 (H)
126 x 90 T1/2 (H)
126 x 140 T7/8 (XH)
Belt Width
LE
25
50
80
38
60
40
10
15
25
25
50
130
38
100
70
20
9.5
25
55
32
60
80
46
60
40
10
15
25
32
60
130
46
100
70
20
9.5
25
55
50
75
80
62
60
40
10
15
25
50
75
130
62
100
70
20
9.5
25
55
75
110
80
94
60
40
10
15
25
75
110
130
94
100
70
20
9.5
25
55
100
140
80
124
60
40
10
15
25
100
150
140
190
130
80
124
174
100
60
70
40
20
10
8
6
9.5
7
25
15
55
25
150
25.4
25.4
25.4
38.1
38.1
50.8
50.8
76.2
101.6
101.6
190
50
50
50
63
63
75.5
75.5
101
126
126
130
80
80
90
80
90
80
90
90
90
140
174
38
38
38
51
51
63.5
63.5
89
114
114
100
60
60
70
60
70
60
70
70
70
110
70
40
40
50
40
50
40
50
50
50
70
20
10
10
10
10
10
10
10
10
10
20
8
6
6
6
6
6
6
6
6
6
8
9.5
7
7
7
7
7
7
7
7
7
10.5
25
15
15
15
15
15
15
15
15
15
25
55
25
25
35
25
35
25
35
35
35
55
Belt Type
25AT5
25T5
25AT10
25T10
25AT20
25T20
32AT5
32T5
32AT10
32T10
32AT20
32T20
50AT5
50T5
50AT10
50T10
50AT20
50T20
75AT5
75T5
75AT10
75T10
75AT20
75T20
100AT5
100T5
100AT10
100T10
100AT20
100T20
150AT10
150AT20
150T20
XL100
L100
H100
L150
H150
L200
H200
H300
H400
XH400
43
L2
L1
RCK 70
Type
44
L3
Self centering.
RCK70 19/47
RCK70 20/47
RCK70 22/47
RCK70 24/50
RCK70 25/50
RCK70 28/55
RCK70 30/55
RCK70 32/60
RCK70 35/60
RCK70 38/65
RCK70 40/65
RCK70 42/75
RCK70 45/75
RCK70 48/80
RCK70 50/80
RCK70 55/85
RCK70 60/90
RCK70 65/95
RCK70 70/110
RCK70 75/115
RCK70 80/120
RCK70 85/125
RCK70 90/130
RCK70 95/135
RCK70 100/145
19
20
22
24
25
28
30
32
35
38
40
42
45
48
50
55
60
65
70
75
80
85
90
95
100
47
47
47
50
50
55
55
60
60
65
65
75
75
80
80
85
90
95
110
115
120
125
130
135
145
Dimensions (mm)
L1
L2
L3
26
26
26
26
26
26
26
26
26
26
26
30
30
30
30
30
30
30
40
40
40
40
40
40
46
31
31
31
31
31
31
31
31
31
31
31
36
36
36
36
36
36
36
46
46
46
46
46
46
52
39
39
39
39
39
39
39
39
39
39
39
47
47
47
47
47
47
47
57
62
62
62
62
62
77
L
45
45
45
45
45
45
45
45
45
45
45
55
55
55
55
55
55
55
67
72
72
72
72
72
89
Torque
Nm
350
390
440
519
590
700
760
930
1030
1240
1350
2170
2350
2510
2580
3200
3380
4160
6840
7500
8100
9700
10300
12100
15700
No.
4
4
4
6
6
6
6
8
8
8
8
6
6
6
6
8
8
8
8
8
8
10
10
10
8
Clamping Screws
Type
Torque
Nm
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M6x25
17
M8x30
41
M8x30
41
M8x30
41
M8x30
41
M8x30
41
M8x30
41
M8x30
41
M10x35
83
M10x35
83
M10x35
83
M10x35
83
M10x35
83
M10x35
83
M12x45
145
Pressures
Shaft
Hub
N/mm 2
N/mm 2
228
98
231
100
220
95
215
102
230
105
220
110
200
120
230
114
200
119
210
124
200
125
236
140
236
140
218
135
218
135
223
145
198
157
213
140
225
143
210
138
200
130
210
145
200
138
210
148
216
148
L
L3
L2
D1
D2
RCK 80
L1
Type
RCK80 10/16
RCK80 12/18
RCK80 14/23
RCK80 15/24
RCK80 16/24
RCK80 18/26
RCK80 19/27
RCK80 20/28
RCK80 22/32
RCK80 24/34
RCK80 25/34
RCK80 28/39
RCK80 30/41
RCK80 32/43
RCK80 35/47
RCK80 38/50
RCK80 40/53
RCK80 42/55
RCK80 45/59
RCK80 48/62
RCK80 50/65
RCK80 55/71
RCK80 60/77
RCK80 65/84
RCK80 70/90
RCK80 75/95
RCK80 80/100
RCK80 85/106
RCK80 90/112
RCK80 95/120
D1
10
12
14
15
16
18
19
20
22
24
25
28
30
32
35
38
40
42
45
48
50
55
60
65
70
75
80
85
90
95
16
18
23
24
24
26
27
28
32
34
34
39
41
43
47
50
53
55
59
62
65
71
77
84
90
95
100
106
112
120
25
28
35
40
40
42
43
44
48
50
50
55
57
59
62
66
69
71
80
81
86
92
98
105
113
119
125
131
137
142
Dimensions (mm)
D2
L1
L2
28
32
39
45
45
47
49
50
54
56
56
61
62
65
69
72
75
78
86
87
92
98
104
111
119
126
131
137
144
149
14
14
14
16
16
19
19
19
26
26
26
25.5
25.5
25.5
31.5
31.5
31.5
31.5
45
45
45
55
55
55
65
65
65
65
65
65
23.5
23.5
23.5
29.5
29.5
32.5
32.5
32.5
39.5
39.5
39.5
39.5
39.5
39.5
45.5
45.5
45.5
45.5
62.5
62.5
62.5
72.5
72.5
72.5
86.5
86.5
86.5
86.5
86.5
86.5
L3
27.5
27.5
27.5
36.5
36.5
39.5
39.5
39.5
46.5
46.5
46.5
46.5
46.5
46.5
52.5
52.5
52.5
52.5
71
71
71
81
81
81
96.5
96.5
96.5
96.5
96.5
96.5
31.5
31.5
31.5
42.5
42.5
45.5
45.5
45.5
52.5
52.5
52.5
52.5
52.5
52.5
58.5
58.5
58.5
58.5
79
79
79
89
89
89
107
107
107
107
107
107
Clamping Screws
Torque No.
Type
Torque
Nm
Nm
35
3
M4x12
5
58
4
M4x12
5
69
4
M4x12
5
170
4
M6x18
17
180
4
M6x18
17
200
4
M6x18
17
210
4
M6x18
17
220
4
M6x18
17
250
4
M6x18
17
395
6
M6x18
17
410
6
M6x18
17
465
6
M6x18
17
510
6
M6x18
17
705
8
M6x18
17
790
8
M6x18
17
860
8
M6x18
17
900
8
M6x18
17
940
8
M6x18
17
1840
8
M8x22
41
2000
8
M8x22
41
2100
8
M8x22
41
2580
9
M8x22
41
2800
9
M8x22
41
3050
9
M8x22
41
5250
9
M10x25
83
5600
9
M10x25
83
8000
12 M10x25
83
8500
12 M10x25
83
9000
12 M10x25
83
11000 12 M10x25
83
Pressures
Shaft
Hub
N/mm 2 N/mm 2
140
85
150
100
140
80
158
98
148
98
180
125
170
120
160
115
115
80
146
102
140
102
135
98
127
90
146
108
105
80
100
76
96
72
90
70
110
85
105
80
100
75
85
65
75
60
70
55
90
70
80
65
100
80
95
75
90
75
100
80
45
Pre-Tension
The purpose of pre-tension is to allow the belt to run without sagging. The pre-tension is correctly set when the slack span remains
taut under the maximum operating loads, ensuring trouble free meshing with the pulleys. Without the correct pre-tension the belt
can run up over the teeth of the driven pulley, and thus increase friction, leading to high noise, wear, and poor positional accuracy.
In order to ruduce bearing loads the pre-tension should not be set too high.
The ideal pre-tension FV is determined mathematically as a function of the maximum peripheral force FU ,as shown in the table
below.
Dive Type
ZB<60
FV=FU/3
60ZB<150
FV=FU/2
150<ZB
FV=2FU/3
FV=FU
FV>FU
All Belts
FV=FU
Influencing Factors
Belt Stiffness
The frictional forces caused by tooth meshing, especially on the non-load carrying span, cause an increase in the span load, which
in turn cause the belt to elongate in proportion to its stiffness, casuing additional wear. The stiffness and high resistance to
elongation in Synchroflex, Breco, and Brecoflex belts reduces the need for high tension.
Peripheral Force
The elongation of the load carrying side of the belt is proportional to the power and peripheral force. Too much slack can be avoided
if the peripheral force is taken into account when pre-tensioning. NB. Multiple shaft and linear drives require the pre-tension and
peripheral force to be added together to arrive at the total working load.
Belt Length
The elongation of the belt, due to the peripheral forces is proportional to the belt length, which is a factor affecting tooth jumping.
Even a short belt which is not subject to high peripheral forces will elongate to some extent. Such short belts will benefit from a
small amount of pre-tensioning to avoid tooth jumping. It should be noted that with short belts any pulley concentricity problems can
produce large variations in tension giving extreme peak values.
Span Length Ratio
In multiple shaft designs the loaded span is usually longer than the slack span, resulting in less elongation in the loaded span
coupled with reduced tension in the slack span. The pre-tension in such drives should be somewhat higher than the peripheral
force.
Transmission Accuracy
Synchroflex, Breco, and Brecoflex belts used in a reversing drives (where the loaded and slack spans alternate) can achieve high
levels of positional accuracy when the pre-tension matches the maximum peripheral force.
46
Pre-Tension
Measurement using Span Deflection
By applying the test load FP (N) in the middle of the belt span and measuring the span deflection h, it is possible to check the pretension.(a minimum of one pulley must able to turn freely)
h = 1.66 102 IT
2
FP =
P 6.48 10
I
+ f0 b T
n1 d 01
LB
5
IT = a 2
d d 01
02
FP
FW
P
n
d0
f0
b
IT
a
h
LB
k
m
Test load N
Shaft load
in kW
R.P.M
Pitch circle diameter (mm)
Elongation factor N/mm
Belt width (mm)
Span length (mm)
Centre distance (mm)
Span deflection (mm)
Belt length (mm)
Constant specific to each belt
Belt weight kg/m
Elongation Factor
K1.5, T2, M, T2.5
T5, T5-DL
T10, T10-DL
T20
T20-DL
AT5
AT10
AT20
0.200
0.285
0.514
1.210
1.820
0.470
1.210
1.820
Fpt = 4 m IT f 2
Fpt =
k b IT f
100
With the pre-tension known , the corresponding natural frequency can be found.
f =
Fpt
2
4 m IT
f =
100Fpt
2
k b IT
SM4 Tension Meter
Accuracy 5%
Range 6 - 350 Hz
can be
Type
T2-M
T2.5
AT3
T5
AT5
T10
AT10
T20
AT20
XL
L
H
XH
Constant k
Single sided Double sided
0.40
0.42
0.90
0.90
1.20
1.35
1.40
1.90
2.30
2.50
2.80
3.00
4.00
4.00
5.30
1.00
1.50
1.80
1.80
1.90
4.20
47
Distributed by
P.I.E.S.