Aceite SKF LHMF 300
Aceite SKF LHMF 300
Product identifier
Product description
N/Av
LHMF 300/5
Product use
Trade name
40 Executive Court
NL-3430 BA
M1S 4N4
Emergency tel. #
Ingredients
Paraffinic base oil
Paraffinic base oils
% (weight)
LD50
inh, rat
oral
dermal
72623-85-9
30.00 - 60.00
N/Av
>2000 mg/kg
72623-87-1
30.00 - 60.00
>5000mg/m (rat)
>2000 mg/kg
(rabbit)
(rabbit)
Routes of exposure
Inhalation
: If product is heated or mists are formed, inhalation may cause irritation to the nose, throat and respiratory
Skin
: May cause mild transient irritation. Prolonged contact, such as when trapped against the skin under clothing
tract.
or jewelry, may be more irritating. Hydrocarbons injected into the skin under pressure can cause severe
injury.
Eyes
Ingestion
: May cause mild eye irritation. Symptoms will include pain, redness and tearing.
: Low degree of toxicity. May have laxative effects. May cause nausea, vomiting, and diarrhea.
Prolonged or repeated skin contact may cause defatting and drying resulting in irritation and
possible dermatitis.
Carcinogenic status
If breathed in, move person into fresh air. If breathing has stopped, give artificial respiration.
Get medical attention/advice if you feel unwell.
Page 1 of 5
LHMF 300/5
Skin contact
In case of contact with skin, wash with mild soap and plenty of water. If irritation persists,
seek prompt medical attention. Wash contaminated clothing before re-use. Subcutaneous
injection may require surgical treatment.
Eye contact
Ingestion
Immediately flush eyes with plenty of water for at least 15 minutes. If irritation persists, seek
prompt medical attention.
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Get
medical attention.
Not flammable under normal conditions of handling. Liquid may burn upon heating to
temperatures at or above the flashpoint. Empty containers retain residue (liquid and/or
vapour) and can be dangerous. Minor contamination by hydrocarbons of higher volatility may
increase flammability. Do not pressurize, cut, heat or weld empty containers. Keep away
from heat and sources of ignition.
Flash point
>200C
ASTM D 93
Auto-ignition temperature
: >350C
N/Av
Oxidizing properties
None known.
N/Ap
: N/Av
Flashback observed
: N/Ap
Dry chemical, foam, carbon dioxide and water fog. Do not use water jet, as this may spread
burning material.
Firefighters should wear proper protective equipment and self contained breathing apparatus
with full face piece operated in positive pressure mode. Move containers from fire area if safe
to do so. Water spray may be useful in cooling equipment exposed to heat and flame. Direct
water or foam spray may cause frothing which can increase the intensity and range of the
fire.
Restrict access to area until completion of clean-up. Ensure clean-up is conducted by trained
personnel only. All persons dealing with clean-up should wear the appropriate protective
equipment including self-contained breathing apparatus. Keep all other personnel upwind
and away from the spill/release.
Environmental precautions
Spill response/cleanup
Do not flush into surface water or sanitary sewer system. For large spills, dike the area to
prevent spreading.
Ventilate area of release. Eliminate all ignition sources. Stop the spill at source if it is safe to
do so. Cover any spilled material with non-combustible absorbent material, such as
vermiculite or sand, then place absorbent material into a container for later disposal (see
Section 13). Clean contaminated floors and objects thoroughly while observing environmental
regulations. Notify the appropriate authorities as required.
Prohibited materials
None known.
Wear suitable protective equipment during handling. Use in a well ventilated area. Avoid
breathing vapours. Avoid contact with skin, eyes and clothing. Keep container tightly closed
when not in use. Keep away from heat and flame. Keep away from incompatibles. Handle
and open container with care. Wash thoroughly after handling. Warning: High pressure
greasing equipment is capable of injecting product under the skin. Such apparatus should be
handled with care. See Section 3.
Page 2 of 5
LHMF 300/5
Storage requirements
Store in a cool, dry, well ventilated area, away from heat and ignition sources. Store away
from incompatible materials. Storage area should be clearly identified, clear of obstruction
and accessible only to trained and authorized personnel. Inspect periodically for damage or
leaks.
Incompatible materials
Avoid contact with strong oxidants such as liquid chlorine, concentrated oxygen, sodium
hypochlorite or calcium hypochlorite.
Always keep in containers made of the same materials as the supply container.
Ingredients
Paraffinic base oil
OSHA PEL
PEL
STEL
N/Av
N/Av
mist, mineral')
mist, mineral')
STEL
N/Av
N/Av
mist, mineral')
mist, mineral')
Use with adequate ventilation. Local ventilation is recommended if the product is misted or
used in a confined space, or if the TLV is exceeded.
Respiratory protection
Skin protection
Depending on conditions of use, an impervious apron should be worn. Other equipment may
be required depending on workplace standards. An eyewash station and safety shower should
be made available in the immediate working area. Remove and wash contaminated clothing
and gloves, including the inside, before re-use. Wash hands before breaks and at the end of
workday.
Liquid.
Appearance
red
Odour
Mineral oil
Odour threshold
N/Av
pH
N/Av
Boiling point
200C
Specific gravity
0.882
Melting/freezing point
< - 25C
Solubility in water
N/Av
N/Av
Insoluble.
N/Ap
Volatiles (% by weight)
N/Av
Viscosity
300 cSt
N/Av
N/Av
N/Av
Stable under the recommended storage and handling conditions prescribed. Hazardous
Conditions to avoid
Keep away from excessive heat, open flames, sparks and other possible sources of ignition.
Page 3 of 5
LHMF 300/5
Irritancy of product
Carcinogenic status
Reproductive effects
Teratogenicity
Mutagenicity
Sensitization to material
Synergistic materials
There is no available data for the product itself, only for the ingredients. See Section
2.
No information available.
No data is available on the product itself. The product should not be allowed to enter drains
or water courses, or be deposited where it can affect ground or surface waters.
Ecotoxicological
Methods of disposal
Regulatory
UN Number
Information
TDG
None
TDG
None.
Shipping Name
Not regulated.
Class
not regulated
Group
Label
none
Additional
information
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the
information required by the CPR.
US federal information:
TSCA: All listed ingredients appear on the Toxic Substances Control Act (TSCA) inventory.
Page 4 of 5
LHMF 300/5
References
Prepared for:
05/10/2007
End of document
Page 5 of 5