Professional Documents
Culture Documents
FM DS 07-12 - Plantas Concentradoras PDF
FM DS 07-12 - Plantas Concentradoras PDF
7-12
17-17
September 2010
Page 1 of 120
Table of Contents
Page
1.0 SCOPE ................................................................................................................................................... 6
1.1 Changes ............................................................................................................................................ 6
2.0 LOSS PREVENTION RECOMMENDATIONS ....................................................................................... 6
2.1 General Site ..................................................................................................................................... 6
2.2 Underground Mining Operations ................................................................................................... 10
2.2.1 Critical Mine Processes and Utilities ................................................................................... 10
2.2.2 Wood Timber Sets ............................................................................................................... 12
2.2.3 Vertical Shafts and Shaft Stations ...................................................................................... 14
2.2.4 Underground Belt Conveyors .............................................................................................. 16
2.2.5 Underground Explosives and Blasting Agents .................................................................... 17
2.2.6 Underground Service and Utility Areas ............................................................................... 18
2.2.7 Underground Warehousing ................................................................................................. 18
2.2.8 Underground Handling and Storage of Flammable Liquids ............................................... 18
2.2.9 Underground Handling and Storage of Compressed Gases .............................................. 19
2.2.10 Underground Mobile Equipment ....................................................................................... 20
2.2.11 Underground Fire Water Supplies and Distribution Systems ............................................ 21
2.2.12 Combustible Ores in Underground Metal and Non-Metal Mines ...................................... 22
2.2.13 Naturally Occurring Flammable Gases in Underground Metal and Non-Metal Mines ..... 22
2.2.14 Collapse, Cave-ins, Rock Falls and Rock Bursts in Underground Metal and Non-Metal
Mines ................................................................................................................................. 23
2.2.15 Ventilation Systems for Fire Control .................................................................................. 23
2.3 Surface Mining Operations ............................................................................................................ 23
2.3.1 Mobile Equipment at Surface Mines and Ship Loading Facilities ...................................... 23
2.3.2 Explosives and Blasting Agents at Surface Mines ............................................................. 25
2.3.3 Belt Conveyors at Surface Mines ........................................................................................ 25
2.4 Surface Ore Processing ................................................................................................................ 26
2.4.1 General Site ........................................................................................................................ 27
2.4.2 Crushing Facilities ............................................................................................................... 32
2.4.3 Ore Storage Buildings and Stock Piles ............................................................................... 32
2.4.4 Ore Concentrator Plants (Mills) ........................................................................................... 33
2.4.5 Powerhouse and Utilities ..................................................................................................... 45
2.4.6 Emission and Waste Control ............................................................................................... 46
2.4.7 Mobile Equipment Garages ................................................................................................. 47
2.4.8 Hydro-metallurgical Mineral Solvent Extraction (SX) Processes ......................................... 48
2.4.9 Plastic Equipment ................................................................................................................ 55
2.4.10 Head Frames and Mine Hoists ......................................................................................... 56
2.4.11 Heap Leaching ................................................................................................................... 59
2.4.12 Electrowinning and Electro-refining ................................................................................... 60
2.4.13 Tailings Ponds ................................................................................................................... 61
2.4.14 Production Pipelines .......................................................................................................... 62
2.4.15 Cross Country Rail Lines .................................................................................................. 62
2.5 Surface Coal Preparation .............................................................................................................. 62
2.5.1 Coal Preparation Buildings General ............................................................................... 63
2.5.2 Thermal Coal Dryers ........................................................................................................... 64
2.5.3 Coal Dust Explosion Protection .......................................................................................... 66
2.5.4 Methane Explosion Protection ............................................................................................ 67
2010 Factory Mutual Insurance Company. All rights reserved. No part of this document may be reproduced,
stored in a retrieval system, or transmitted, in whole or in part, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without written permission of Factory Mutual Insurance Company.
7-12
17-17
Page 2
List of Figures
Fig. 1. Photo of typical underground timber set. This set has no lagging. ................................................. 12
Fig. 2. Photo of tunnel with timber sets backed by plank lagging. This arrangement always
creates a potential self sustaining fire. ............................................................................................. 13
Fig. 3. Sketch of shaft and shaft station fire protection system (combination water spray and smoke
detection) developed by the US Bureau of Mines. ......................................................................... 15
Fig. 4. Conveyor belt leaving underground mine portal. ............................................................................ 17
Fig. 5. Underground diesel fueling station. Station is in a rock enclosure but due to rock fall potential the
rock enclosure has been supported by wood planks on steel beams and columns. ..................... 19
Fig. 6. Photo of diesel fueled ore haulage vehicle in underground mine. ................................................. 20
Fig. 7. Drawing of diesel fueled excavator with special suppression system in engine compartment. ..... 21
Fig. 8. Self propelled 190 ton (172 tonne) ore haul truck. ......................................................................... 24
Fig. 9. Large excavating shovel loading a haul truck, in a hard rock open pit mine. ................................ 25
Fig. 10. Fire on a large self propelled front end loader. ............................................................................. 26
Fig. 11. Walking drag line in strip coal mine. .............................................................................................. 27
Fig. 12. Mobile, tracked drilling unit. ........................................................................................................... 28
Fig. 13. Rail mounted ore stacker, bauxite mine. ....................................................................................... 28
Fig. 14. Ore shiploader. .............................................................................................................................. 29
Fig. 15. Rail mounted bucket wheel reclaimer. .......................................................................................... 30
Fig. 16. Partially covered captive conveyor system feeding crushed ore from primary crusher to ore
bin, zinc mine. ................................................................................................................................ 31
Fig. 17. Core storage facility. Cores are stored in wood boxes in metal racks. ........................................ 32
Fig. 18. Outdoor ore stockpile with an open, elevated conveyor system feeding ore from a
nearby rushing facility. ................................................................................................................... 33
Fig. 19. Simplified process flow diagram of a typical metal ore concentrator plant. ................................. 34
Fig. 20. Rubber lined pipes from four separate grind circuits feeding a common rubber lined tank. ....... 35
Fig. 21. View of interior of multi-grind circuit concentrator plant. Much of equipment and piping
shown has rubber linings. .............................................................................................................. 35
Fig. 22. View of rubber lined inlet pipe into a hydrocyclone. ..................................................................... 36
Fig. 23. Hydrocyclone bank with sprinkler protection. ................................................................................ 37
Fig. 24. Warning label on rubber lined tank ............................................................................................... 38
Fig. 25. Warning label hanging on pipe located directly above an open topped rubber lined tank. ......... 38
Fig. 26. Drums of flammable cleaning solvent being used to clean gear teeth of large SAG mill in
copper concentrator. ...................................................................................................................... 42
Fig. 27. Grouped electrical cables in multi-tier trays in concentrator building. .......................................... 43
Fig. 28. Concentrator plant MCC room with high value marshalling cabinets and grouped electrical
cables at the ceiling. ...................................................................................................................... 44
Fig. 29. Diesel fueled generators providing sole source electrical power at remote gold mine.
(Courtesy Rio Tinto) ....................................................................................................................... 46
Fig. 30. Haulage truck inside high bay mobile equipment shop. ............................................................... 47
Fig. A. Close-up of mixer-settler building with protection using foam water chamber at surface of
solvent in upper view, and deluge waterspray or foam water at ceiling in lower view. .................. 50
Fig. B. Protection for building walls (external water curtain) and tank farm details ................................. 50
Fig. C. Outdoor, small-cell SX facility with deluge waterspray over and under vessels and foam inside
vessels.
......................................................................................................................................... 51
Fig. D. Indoor SX plant with deluge waterspray at ceiling, over mixer-settlers, under grating, under
vessels, and foam inside vessels. ................................................................................................... 51
7-12
17-17
Page 3
Fig. E. Pulse columns with flammable organic solvents. Used in uranium and some copper
extractions. Example of deluge fire protection. ............................................................................... 52
Fig. F. Sketch of recommended placement of UV/IR light detectors inside typical copperuranium
SX settler building and inside sub-grade trenches designed to actuate protection systems and
sound alarm ...................................................................................................................................... 53
Fig. G. Drainage to Remote Basin .............................................................................................................. 54
Fig. 33. Plastic ducts at emission control facility, copper refinery. ............................................................. 55
Fig. 34. Wire rope oiling system using sprayer enclosure and demister box. ............................................ 57
Fig. 35. Wire rope oiling system using oil tray. ............................................................................................ 58
Fig. 36a. Hoist brake assembly indicating areas of cracking. ..................................................................... 59
Fig. 36b. Typical defects found .................................................................................................................... 60
Fig. 36c. Cracks on brake shoes. ................................................................................................................ 61
Fig. 37. Private cross country rail line for transporting iron ore from an inland area of Western
Australia to a coastal port. (Courtesy of Rio Tinto) ....................................................................... 63
Fig. 38. Coal mining and processing facility ............................................................................................... 64
Fig. 39. View of thermal dryer showing constriction deck and cyclone collection system. ....................... 65
Fig. 40. Sketch of recommended placement of deluge water spray systems for constriction
deck and cyclones. ........................................................................................................................ 66
Fig. 41. Flow diagram of mining and mineral processing activities from exploration to product sales. .... 68
Fig. 42. Ventilation system using shafts for a deep metal mine. (Figure courtesy of Society of
Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) .......................................... 73
Fig. 43. Drawing of a typical underground mine operation showing chutes, grizzlies, cribs, and typical
ground support methods. (Figure courtesy of Society of Mining, Metallurgy, and
Exploration, Inc. (SME), Littleton, Colorado) ................................................................................. 74
Fig. 44. Head frame structure at modern non-metal mine. Hoist house is to the left. (Courtesy of Elf
Aquitaine, TGI Soda, Grainger WYO) ........................................................................................... 75
Fig. 45. Close up view of head frame in Figure 44, showing wire ropes from adjacent hoist room,
sheave wheel at top, and structural supports. (Courtesy of Elf Aquitaine, TGI Soda,
Grainger WYO) .............................................................................................................................. 76
Fig. 46. Multi-rope, friction-sheave hoisting system, mounted in headframe. (Figure courtesy of
Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ......................... 77
Fig. 47. Typical hoists found in mining operations. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ....................................................... 78
Fig. 48. Isometric layout of an underground mine showing levels and mining terms. (Figure
courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ...... 79
Fig. 49. Plan and cross section views of typical shafts and levels of an underground mine. (Figure
courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ...... 80
Fig. 50. Drawing of underground metal mine supported by ore pillars. Shown is a room and pillar
mining method of an inclined ore body. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 81
Fig. 51. Drawing of a hardrock mine featuring concrete pillars which temporarily support a longwall
mining zone. (Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME),
Littleton, Colorado) ......................................................................................................................... 81
Fig. 52. Examples of rock bolts for ground support. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 82
Fig. 53. Cross section view of a typical wood lined vertical shaft. (Figure courtesy of Society
of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ....................................... 83
Fig. 54. Photograph of large open pit mine. ................................................................................................ 84
Fig. 55. Ore mining of caved pit wall. (Figure courtesy of Society of Mining, Metallurgy, and
Exploration, Inc. (SME), Littleton, Colorado) .................................................................................. 84
Fig. 56. Schematic view of large open pit copper mine and mills. (Bingham Canyon Mine,
Courtesy of Rio Tinto Mining, Kennecott Copper, Utah) ................................................................ 85
Fig. 57. Photograph of surface strip mining of coal. Dragline is used for overburden removal. ................ 86
Fig. 58. Photo of a floating dredge in a placer gold mining operation. ....................................................... 86
Fig. 59. Drawing of a hydraulicking operation in a gold placer bed. (Figure courtesy of Society of
Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................... 87
Fig. 60a. Section view of a single timber set used underground for ground support. ................................ 87
Fig. 60b. Isometric view of a series of timber sets in an underground tunnel. ........................................... 88
Fig. 60c. Section view of a timber set with wood plank lagging ................................................................. 88
7-12
17-17
Page 4
Fig. 60d. Isometric view of a series of timber sets with wood plank lagging .............................................. 88
Fig. 61. Room-and-pillar mining of a flat orebody. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 89
Fig. 62. Room-and-pillar mining of an inclined orebody. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 90
Fig. 63. Sublevel stoping with large hole drilling and blasting. (Figure courtesy of Society of
Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................... 90
Fig. 64. Sublevel stoping with ring drilling as the primary means of breaking ore. (Figure courtesy of
Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) .......................... 91
Fig. 65. Shrinkage stoping in a large vertical orebody. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 91
Fig. 66. Cut-and-fill mining in a large vertical orebody. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 92
Fig. 67. General view of an open stoping mine. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................................ 92
Fig. 68. Longwall mining of coal deposit. (Figure courtesy of Society of Mining, Metallurgy, and
Exploration, Inc. (SME), Littleton, Colorado) .................................................................................. 93
Fig. 69. Sublevel caving in a large and steeply dipping orebody. (Figure courtesy of Society of
Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................................... 94
Fig. 70. Block caving in a massive orebody, showing a conventional mining layout. (Figure
courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ....... 95
Fig. 71. Photo of A-Frame building for bulk coal storage, with incline, totally enclosed conveyor belt
delivery and reclaim system. .......................................................................................................... 95
Fig. 72. Photo of gas cooling, scrubbing, and precipitation equipment associated with a typical
emission control acid plant. Most of equipment and ducting in this photo are of fiber
reinforced plastic construction. ....................................................................................................... 96
Fig. 73. Photo of a series of typical ball mills in a copper concentrator. .................................................... 97
Fig. 74. Cutaway view of the interior of a ball mill. ..................................................................................... 97
Fig. 75. Photo of a flotation circuit in a copper concentration mill. ............................................................. 98
Fig. 76. Coal preparation plant using a hillside for gravity flow of product. ............................................... 99
Fig. 77. Concentrator complex at diamond mine. (Photo courtesy of Rio Tinto) ...................................... 100
Fig. 78. Gold mine concentrating facility. Due to tropical location much of process area is located
outdoors. ...................................................................................................................................... 101
Fig. 79. In-pit crushing station at large copper mine. (Courtesy of Rio Tinto, Kennecott Copper,
Bingham Canyon Mine, Utah) ...................................................................................................... 102
Fig. 80. Drawing of a movable crusher mounted on a crawler transporter. (Figure courtesy of
Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ....................... 102
Fig. 81. Photo of a mobile crusher at open pit mining operation. (Courtesy of Alcoa) ............................ 103
Fig. 82. Drawing of a gyratory crusher inside a multistory reinforced concrete crushing facility. (Figure
courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ..... 104
Fig. 83. Drawing of in-situ solution mining (cyanide leaching) in an open pit. (Figure courtesy of
Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ........................ 105
Fig. 84. Photo of a copper electro-refining cell (tank) house. Walkways between cells are wood plank.
Cells are concrete lined with a thin polymer plastic. (Courtesy of Cominco Quebrada, Chile) .. 105
Fig. 85. Photo of plastic screen (blue) inside flotation tank. Also refer to photo of flotation circuit
under Beneficiation, above. ......................................................................................................... 106
Fig. 86. Photo of world-class size semi-autogenous (SAG) mill in copper concentrator facility.
(Courtesy of Rio Tinto) ................................................................................................................ 107
Fig. 87. Photo of large DC drive motor for this SAG mill. (Courtesy of Rio Tinto) .................................. 108
Fig. 88. Photo of parallel ball mills in a copper concentrator facility. (Courtesy of Rio Tinto) ................. 109
Fig. 89. Cutaway view drawing of a rod mill, showing internal components. .......................................... 109
Fig. 90. Process flow diagram of a grind circuit featuring multiple stages of crushing with ball and
rod mill grinding. ........................................................................................................................ 110
Fig. 91. Process flow diagram of a grind circuit featuring a single crusher with SAG and ball mill
grinding. ..................................................................................................................................... 110
Fig. 92. Photo of a cross valley gold heap leaching operation, built into a sloping mountain. (Photo courtesy of Newmont Mining Company, Yanacocha Mine, Peru) ....................................................... 111
Fig. 93. Drawing of heap leach operation showing pile and pregnant solution collection pond. ............. 111
Fig. 94. Closeup drawing of heap leach pile showing cyanide solution distribution system. .................. 112
7-12
17-17
Page 5
Fig. 95. Photo of rubber lined raffinate pond at copper heap leaching and solvent extraction mine.
(Courtesy of Cominco Quebrada, Chile) ..................................................................................... 112
Fig. 96. Photo of hydrocyclone bank (six hydrocyclones) positioned over a collection tank. These
hydrocyclones and the discharge tank are all rubber lined. ....................................................... 113
Fig. 97. Close up view of single rubber lined hydrocyclone in bank. ....................................................... 113
Fig. 98. Sketch of water injected hydrocyclone. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado) ..................................................... 114
Fig. 99. Process flow of a typical heap leaching, carbon-in-pulp, and electrowinning circuit for
hydrometallurgical recovery of gold and silver. ........................................................................... 114
Fig. 100. Typical solvent extraction process flow for copper. ................................................................... 115
Fig. 101. Photo of rubber liner inside a ball mill. ....................................................................................... 115
Fig. 102. Photo of rubber liner inside a large diameter steel pipe flange. ............................................... 116
Fig. 103. Photo of pyrometallurgical process zinc roaster. (Photo courtesy of Cominco, Peru) .............. 117
Fig. 104. Shaker screen, constructed of high density polyurethane plastic. ............................................. 118
Fig. 105. Photo of SX plant at copper mine. (Photo courtesy of Cominco Quebrada, Chile) .................. 118
Fig. 106. Tailings pond at zinc refinery. .................................................................................................... 119
Fig. 107. Thickener tanks at copper concentrator plant. (Courtesy of Rio Tinto) .................................... 119
Fig. 108. Photo of exposed plastic trommel screen at outlfow of large SAG mill. .................................. 120
List of Tables
Table 1: Example of altitude corrected flash point for a material having a flash point of
105F (41C) at mean sea level (MSL) ........................................................................................... 8
Table 2. Common flotation reagents. .......................................................................................................... 39
7-12
17-17
Page 6
1.0 SCOPE
The following mining and ore processing occupancies and hazards are included in this data sheet:
Underground and surface mining (extraction) of metal and non-metal minerals. Examples of metal minerals
are gold, silver, copper, tin, lead, tungsten, zinc, uranium, and vanadium. Non-metal minerals include sulfur,
salt, potash, marble, limestone, gypsum, gemstones and aggregate rock products.
Surface mining of fossil coal. Examples of fossil materials are anthracite and bituminous coal, lignite coal,
oil shale, tar sands, peat, liquid petroleum, and natural gas. Of the fossil materials, this data sheet covers
only surface mining and preparation of coal, which includes anthracite, bituminous, and lignite grades.
Mining and processing operations only on or under the surface of the earth or on shallow bodies of water
such as lakes or streambeds.
Metal and non-metal mineral processing and coal preparation which includes mineral or material transfer,
sizing, washing, cleaning, drying, beneficiation, and concentration. Mineral transfer includes delivery from
the mine to process plants, stockpiling, reclaim systems, and shipment by conveyor, rail, or other land
vehicles to load out facilities including remote ship loading ports.
Electrometallurgical (e.g., gold electrowinning, copper electro-refining) and hydrometallurgical (e.g., heap
leaching and solvent extraction) refining processes.
The following mine occupancies or hazards are not included in this data sheet:
Underground coal mining (extraction) (collieries)
Oil shale, petroleum, tar sands and natural gas mining, extraction and processing.
Pyrometallurgical refining processes (e.g., smelting, roasting, oxidizing, reducing, sintering or agglomerizing of metals such as copper, lead, nickel, zinc and iron) and aluminum refining and smelting (which are
covered in Data Sheet 7-64/13-28, Aluminum Industry.)
Emission control acid plants associated with smelters or ore oxidation/reduction plants
Deep-sea extraction of minerals
End use of refined or prepared minerals and coal (such as metal working facilities, fossil material power
plants, and coal gasification plants).
Habitation, institutional, transportation, industrial, agricultural, manufacturing, storage, or defense uses of
underground facilities, even if originally occupied for mineral extraction.
1.1 Changes
September 2010. Minor editorial changes were made for this revision.
2.0 LOSS PREVENTION RECOMMENDATIONS
Section 2.0 provides recommended guidance for protection of mines and ore processing plants against perils
including fires, explosions, miscellaneous exposures, and boiler and machinery exposures. Only property
damage and associated business interruption exposures are covered in this document.
The risk management goal should be to improve a mining and ore processing site to qualify as a Highly
Protected Risk (HPR). Where possible in new facilities eliminate or minimize combustibles in the construction and occupancy. Combustible materials should be substituted by less combustible materials where
possible in existing facilities. Especially avoid the use of plastics in construction and occupancy to prevent
costly fixed fire protection. Plastics represent severe fire potentials and cause liberation of dense smoke and
by product gases which can cause direct damage to sensitive electronic equipment or impede emergency
response, especially in underground mines.
2.1 General Site
2.1.1 For new facilities, construct buildings, special structures, and mine passageways and shafts of
noncombustible or fire resistive construction. The performance goal is to reduce combustible construction
loading to minimize the need for active protection systems. Plastic should be avoided, especially underground.
2.1.2 For new facilities, avoid or minimize polymeric occupancy materials such as conveyor belts, plastic
cable insulation, rubber liners, plastic equipment, wood liners, plastic insulating or corrosion resisting
materials, combustible and flammable liquids. These should be replaced by non combustible, fire safe, fire
7-12
17-17
Page 7
resistant, or fire retardant materials if possible. The performance goal is to reduce combustible occupancy
loading to minimize the need for active protection systems.
2.1.3 Process design, safety system design, off-premises utilities, plant construction, and general plant siting
should take into account local or regional exposures from the following natural, catastrophic-type exposures.
Licensed professional or appropriately certified engineers should be responsible for proper design where
these exposures exist. Where exposures cannot be completely eliminated, an emergency contingency plan
should be developed and documented outlining actions to be taken to eliminate or mitigate damage in
advance of pending or potential catastrophe type occurrences.
freezing
strong windstorm, hurricane, cyclone, typhoon, and tornado
flood
wildland fires
earthquake
volcanic activity
snow loading
surface water runoff
landslide
land subsidence
tailing pile, heap leach pad or dam failures
avalanche, glacier, mud or snow slide
abandoned or active underground workings
unusual vibration from blasting, ore processing or mobile equipment
For guidelines on these exposures refer to the following FM Global data sheets:
Data Sheet 1-0, Safeguards During Construction.
Data Sheet 1-1, Firesafe Building Construction and Materials.
Data Sheet 1-2, Earthquakes.
Data Sheet 1-28, Wind Design.
Data Sheet 1-9, Roof Anchorage.
Data Sheet 1-25, Process Tanks and Silos.
Data Sheet 1-54, Roof Loads for New Construction.
Data Sheet 1-57, Plastics in Construction
Data Sheet 1-40, Flood.
Data Sheet 9-18, Prevention of Freeze-Ups.
2.1.4 Protect process buildings, maintenance shops, parts warehouses, mobile equipment service buildings,
employee housing, change houses, utility buildings, research facilities and administration offices against fires
per appropriate FM Global data sheets, whether on the surface or underground. Generally, automatic sprinklers and hydrants backed by an adequate and reliable water supply and water distribution system should be
provided where construction and/or occupancy are combustible and values and economics warrant such protection. (Specific occupancy details and recommendations are covered in Sections 2.2, Underground Mining Operations, 2.3, Surface Mining Operations, 2.4 Surface Ore Processing, and 2.5, Surface Coal
Preparation.)
2.1.5 Protect structures supporting important equipment, piping, conveyors, tramways, and electrical
distribution systems from mobile equipment impact and other mechanical damage. Signs should be posted
and safe clearances designated.
7-12
17-17
Page 8
2.1.6 Ensure that cutting and welding and other hot work or spark producing operations follow the FM Global
Hot Work Permit System or equivalent system, both aboveground and underground.
2.1.7 Ensure that control of combustible materials and good housekeeping are of highest priority in
underground mines, in oil lubricated hoist houses, in buildings where combustible dusts are present, in mobile
equipment maintenance garages, and generally throughout the site. Housekeeping should follow
recommended good practices for the occupancy. Never discard oily rags and other combustible materials
subject to spontaneous combustion in abandoned or infrequently occupied underground workings, in gobs,
near wood timber sets, or near combustible ore bodies unless in special containers.
2.1.8 Control flammable and combustible liquids storage, transfer, and handling by following recognized
good practices and data sheets 7-29, Flammable Liquid Storage in Portable Containers; 7-32, Flammable
Liquid Operations; and 7-83, Drainage Systems for Flammable Liquids. Protect cutting oils in maintenance
garages or millwright shops using Data Sheet 7-37, Cutting Oils. Protect liquefied petroleum gases, such as
propane, using Data Sheet 7-55/12-28, Liquefied Petroleum Gas. Protect compressed gases in cylinders
using Data Sheet 7-50, Compressed Gases in Cylinders; Data Sheet 7-51, Acetylene; Data Sheet 7-52, Oxygen; and Data Sheet 7-56, MAPP Industrial Gas.
2.1.9 Protect bulk storage of diesel and other petroleum based fuels such as gasoline per Data Sheet 7-88,
Storage Tanks for Flammable and Combustible Liquids.
2.1.10 Mine occupancies may be located at high altitudes. Flash points are listed relative to mean sea level
(MSL); however, altitude can have a significant effect on flash point. Before determining fire protection
requirements, adjust flammable and combustible liquid flash points for altitude by using the following equation:
EQ 1:
where:
Fc = the flash point (F) corrected to desired altitude;
Fsl = flash point (F) at sea level;
760 mm Hg = the average barometric pressure at sea level;
P = average barometric pressure at the given altitude, expressed in mm Hg.
(Note that Equation 1 only works in the units given. There is no metric equivalent)
Representative average barometric pressures at several different altitudes are given in Table 1. Example
corrections for a 105F (41C) mean sea level (MSL) flash point combustible liquid are also given in Table 1.
Note that the example material, which is a Class II combustible liquid at MSL becomes a Class I flammable
liquid at approximately 3500 ft (1067 m) and has a major impact at 14,000 ft (4268 m). This can notably
effect the handling and protection of diesel fuel which is used in large quantities in high altitude mines.
Table 1: Example of altitude corrected flash point for a material having a flash point of
105F (41C) at mean sea level (MSL)
Altitude
ft
MSL
1000
2000
5000
8000
10000
12000
14000
m
MSL
305
610
1524
2439
3048
3658
4268
Barometric Pressure
(mm Hg)
760
732
706
632
565
523
483
446
Flash Point
F
105
103
102
97
93
91
88
86
C
41
39
39
36
34
33
31
30
2.1.11 Diesel fuels used in remote high altitude areas or areas subject to extreme temperatures may have
low flash point additives such as butane to enable easier mobile equipment function and engine starting.
When evaluating diesel fuel handling and storage fire protection requirements, use the actual flash point
tested with the mixed additive instead of the pure diesel fuel.
7-12
17-17
Page 9
2.1.12 Have administrative controls and procedures in place and backed by management to assure adequate
supervision and inspection of fire protection equipment, emergency preparedness and response, and
maintenance programs. Refer to Data Sheet 9-7/17-5, Property Conservation; Data Sheet 2-81, Fire Satefy
Inspections and Sprinkler System Maintenance; and other specific data sheets.
2.1.13 Control common ignition sources such as smoking, open flames, and cutting and welding by
administrative programs. Develop preventive maintenance and housekeeping programs to minimize ignition
sources from other sources such as conveying equipment, machinery, friction, hot surfaces, spontaneous
combustion, portable heaters, and the like.
2.1.14 Install all electrical equipment in accordance with Data Sheet 5-7, National Electrical Code (or
international equivalent) throughout mill or mining areas. Protect grouped electric cables in accordance with
Data Sheet 5-31, Cables and Bus Bars. Establish a program of electrical maintenance in accordance with
manufacturers instructions and Data Sheet 5-20, Electrical Testing. Protect electrical systems against lightning and surges as outlined in Data Sheet 5-11, Lightning Surge Protection for Electrical Systems. Underground mines may need special attention to lightning protection to assure metal pipes or wire ropes do not
channel surface lightning strikes to below-surface equipment.
2.1.15 Conduct predictive maintenance and testing, including non-destructive examinations (NDE), of
important fired, pressurized, mechanical, and electrical vessels and equipment (including mobile and semistationary mining vehicles) at intervals recommended by the equipment manufacturer, local codes, or as
outlined in FM Global data sheets for specific equipment. Generally, due to the harsh environment in mining
occupancies, especially underground, inspection and maintenance frequencies may need to be increased.
The use of a computerized reliability based maintenance tracking and control system is advised.
2.1.16 A formal process safety management (PSM) system should be adopted where chemical processes
(such as solvent extraction, ore reduction or oxidation, autoclave, acid recovery, smelting, etc.) exist. The PSM
program should feature the following minimum requirements, as published by the American Institute of
Chemical Engineers (AIChE), Center for Chemical Process Safety (CCPS), or foreign equivalents. Refer to
Data Sheet 7-43, Loss Prevention in Chemical Plants, for details and bibliography of selected reading on
development and maintenance of PSM programs.
a) Management Accountability and Responsibility
b) Process Safety Knowledge and Documentation
c) Process Risk Management
d) Process Hazard Analysis
e) Management of Change
f) Mechanical Integrity
g) Incident Investigation
h) Training and Performance
i) Human Factors
j) Emergency Response Planning
k) Audits and Corrective Actions
2.1.19 Ensure each mine site has an emergency response capability commensurate with the exposure and
the presence or lack of nearby public or mutual aid response organizations. This capability should take into
account required staffing, procedures, training, equipment, and specialized needs such as proper design
and emergency control of underground ventilation systems. To enable the emergency response team or plant
emergency organization to be effective, event scenarios should be developed for difficult fire situations,
pre-plans made, and full scale fire response simulations held at least annually. Event scenarios needing
pre-planning may include, but not be limited to, underground timber set or shaft fires; underground or aboveground (highly elevated) conveyor belt fires; concealed rubber lined equipment fires; and plastic equipment
fires. Place into effect, document, and update post incident contingency plans to assure fast restoral of
production.
7-12
17-17
Page 10
7-12
17-17
Page 11
Usually due to size there is only one hoist motor per hoist shaft and loss of this equipment will shutdown that shaft. Because most codes require at least two methods of safety egress from a mine, loss
of one will often completely stop operations. This equipment is susceptible to fire (from lubrication and
hydraulic oil systems and in some cases combustible fuels) and mechanical impact or electrical breakdown or other damage such as metal fatigue. Wire ropes can sever and cause skips and cages to fall into
the shaft. Buildings may be susceptible to ground subsidence if over shallow underground workings, or
be exposed to other natural exposures.
f) Mine Production Air Many mines use compressed air for machinery underground. Often, small
portable compressors are used for this purpose and if lost to fire or mechanical damage would not
significantly effect production. In some cases a single large compressor has been used to supply mine
production air via pipelines from the surface. Loss of this unit would disrupt mine operations. This
equipment may be housed in combustible buildings in older facilities. Loss can occur from fires in oil lubrication systems and from mechanical breakdown. The building housing the compressor may be susceptible to ground subsidence if over shallow underground workings, or be exposed to other natural exposures.
Pipeline distribution systems are susceptible to rockfall.
g) Mine Ore Production Processes Some mines have primary crushing equipment underground. The
crushed ore is then sent via conveyors or vertical hoist systems to surface secondary crushing circuits.
Crushers are high value, long lead time equipment and hydraulic and lubricating oil systems and grouped
electrical cables represent fire exposures. They are designed to withstand harsh conditions but can have
mechanical breakdown due to metal fatigue or sudden impact primarily. Large (usually electric) motors
which drive crushers can suffer mechanical or electrical breakdown. Important components of crushers
(such as cones, jaws or mantles and large unique motors) should be spared. Combustible fluids should be
protected. Conveyor systems should be protected. Pumps and machinery for in-situ solvent processing
should be evaluated for reliability, spares, and properly protected. Important production mining equipment
is covered below.
2. Reference the following FM Global data sheets for protection of these critical systems. In some cases,
due to harsh operating conditions underground, maintenance and testing to prevent mechanical of electrical
breakdown may need to exceed guidelines intended for less harsh aboveground conditions.
Data Sheet 5-4, Transformers.
Data Sheet 5-13, Synchronous Motors.
Data Sheet 5-17, Large Electric Motors.
Data Sheet 5-18, Protection of Electrical Equipment.
Data Sheet 5-19, Switchgear and Circuit Breakers.
Data Sheet 5-20, Electrical Testing.
Data Sheet 5-23, Emergency and Standby Power Systems.
Data Sheet 5-24, Miscellaneous Electrical Equipment.
Data Sheet 5-31, Cables and Bus Bars.
Data Sheet 6 Series, Industrial Heating.
Data Sheet 7-13, Mechanical Refrigeration.
Data Sheet 7-95, Compressors.
Data Sheet 7-98, Hydraulic Fluids.
Data Sheet 12-61, Mechanical Refrigeration.
Data Sheet 13-6, Flywheels and Pulleys.
Data Sheet 13-7, Gears.
Data Sheet 13-3, Steam Turbines.
Data Sheet 13-17, Gas Turbines.
Data Sheet 13-24, Fans and Blowers.
7-12
17-17
Page 12
Fig. 1. Photo of typical underground timber set. This set has no lagging.
Testing by FM Global Research under contract to the United States Bureau of Mines (USBM) on fires in timber sets, even without lagging, has demonstrated the potential for self propagating fire spread given the right
combination of timber dimensions and spacing. Conversely, if the timber sets are spaced far enough apart
and lagging is not present, testing shows that a fire will not self propagate beyond the incipient ignition zone,
even with strong ignition sources such as fuel. Refer to USBM Information Circular (IC) 8865, 1981, An
Experimental Investigation of the Fire Hazards Associated with Timber Sets in Mines, pgs 86-105.
7-12
17-17
Page 13
Fig. 2. Photo of tunnel with timber sets backed by plank lagging. This arrangement always
creates a potential self sustaining fire.
1. Preferably, remove wood timber sets and lagging from tunnels and drifts and replace with modern
noncombustible mine support systems. Options include use of concrete, aluminum, or steel sets, rock bolting,
bolted wire curtains, corrugated steel panels, or spray coating timber sets and rock surfaces with a
cementitious coating such as Shotcrete or Gunite. (Note: new products using foamed isocyanurate based
plastic have recently been introduced. They are being marketed as suitable for structural supports for mine
passageways. Claims have been made as to fire retardantcy based on small scale ASTM tunnel testing.
However, until such materials have been tested and accepted or approved by FM Global Research for specific
in-mine applications, they should be considered flame propagating and their use underground discouraged.)
2. Contact a FM Global Research Mine Occupancy Specialist if it is uneconomical or unfeasible to completely remove or reduce wood timber sets. The specialist will conduct a focussed evaluation to determine
the potential for self sustained fire spread using results from the FM Global Research tests. Where a focussed
evaluation of fire spread has not been made, it a should be assumed the timber set is self propagating until
proven otherwise. Where lagging is present, the potential for self propagating fire spread should also be
assumed.
3. When a focussed evaluation of timber sets concludes self sustaining fire propagation potential or where
continuous wood lagging is present behind timber sets, one of the following alternative fire protection
schemes should be applied:
a) Provide automatic sprinklers, backed by an adequate and reliable water supply, throughout tunnels
and interconnected rooms having wood timber sets and/or lagging. Use pendent 165F (74C) sprinklers
in the upright position and design to provide 0.15 gpm/ft2 (6 mm/min) density over 2000 ft2 (186 m2). For
wide tunnels two or more rows of sprinklers may be needed.
b) As an alternative to sprinkler protection cover the wood timber set or lagging with a sprayed on
cementitious coating such as gunnite or shotcrete.
c) As a third but less desirable alternative, break up the timbered passageway by rated fire barriers or
zones of noncombustible or protected construction every 2000 lineal feet (610 lineal meters). (Note that
barriers may restrict ventilation control and might not be possible or practical).
7-12
17-17
Page 14
i. If a fire barrier is used, it should be noncombustible, rated at two hours fire resistance, tightly seal
the passageway, and openings through the barrier should be automatic closing upon smoke detection,
or be normally maintained in the closed position.
ii. If noncombustible or protected zones are used, design the length of the defined zone to at least
50 times the hydraulic diameter* of the passageway. To assure fire propagation will be stopped by the
defined zone, the zone should not have significant combustible timber sets; lagging should not be
present; and the zone should not be used for combustible storage or temporary staging of fueled
vehicles. An alternative to eliminating combustibles is to provide automatic sprinkler protection in the
defined zone only. Use of polymeric materials (such as electrical cables in trays or rubber hose) are
permitted in designated noncombustible zones as long as concentration of such materials is not
considered significant or prone to fast fire spread through the zone.
* Hydraulic diameter (Dh ) can be calculated by the following equation:
EQ 2:
Dh = 2(W H)/(W + H)
Where W = the average width of the passageway (ft or m) and H = the average height (ft or m).
Example: Assume a mine tunnel with timber sets that produce a self sustaining fire propagation with walls
an average of 20 ft (6.1 m) wide and floor-to-back (roof) height of 10 ft (3 m). Using EQ 2, Dh = 13.3 ft (4 m).
To achieve non-propagation, the timber should be removed or protected for 50 times 13.3 ft (4 m) or 665 ft
(202 m).
2.2.3 Vertical Shafts and Shaft Stations
A vertical shaft is one with an incline between 45% and 90%.
A shaft station is an enclosure (room) at each level where the shaft exits into a working area of the mine.
The station is used for personnel ingress and egress and for delivery of supplies including fuels.
Most modern mines will have noncombustible shaft liners and steel infrastructure although wood continues
to be used in many countries. Older mines almost always have wood liners and significant wood infrastructure.
Plastic liners are rare.
Metal mines are often wet and wood shaft liners may be saturated with water. Some non-metal mines, while
drier, may have inorganic materials (such as naturally fire retardant potassium carbonate in potash mines)
that have impregnated the wood lining over time. Either of these can effect potential for fire spread. When very
wet liners (essentially saturated) are encountered and it is determined that this is normal and consistent
throughout the shaft (for approximately 10 hydraulic diameters above shaft stations), it is unlikely fixed fire
suppression is needed. (See Equation 2 in section 2.2.2 to calculate hydraulic diameter)
1. Design new mines with noncombustible shaft liners. Preferably, in existing mine shafts remove wood
timbers, wood lagging, and other combustible liners and replace with modern noncombustible liners. One
option is to spray coat rock surfaces with cement or line the shaft with noncombustible materials such as metal
panels or concrete. Another is to remove only the wood lining exposed to significant ignition sources, such
as at shaft stations. Use guidelines for sprinklers, based on 10 hydraulic diameters, outlined below, for needed
liner removal distances.
2. Do not use plastic liners for new mine shafts. Replace plastic liners with noncombustible liners. In existing
mine shafts, protection of plastic liners should be designed based on Data Sheet 1-13, Chimneys.
3. Refer to Data Sheet 1-13, Chimneys, for general protection and prevention guidelines that are similar to
lined vertical shafts.
4. If it is uneconomical or unfeasible to completely remove wood lining from inside a vertical shaft the following
should be done:
a) Determine flame spread by submitting samples of the wood lining to FM Global Research for Fire
Propagation Index (FPI) testing using the FM Global Research 50 kW-scale Flammability Apparatus.
(Some wet or ore impregnated wood liners have not supported vertical fire spread in shafts.)
b) If the FPI is greater than 7 (indicating self propagating fire spread, install a water deluge fire suppression system inside the shaft 10 times the hydraulic diameter (Dh) above each active sublevel shaft station
entrance where fueled mobile equipment or other high energy ignition sources are or may be present
for upcast ventilation shafts, or 10Dh below the station for downcast ventilation shafts. See Equation 2
7-12
17-17
Page 15
in Section 2.2.2 for a method to determine hydraulic diameter (Dh). (Note: When ventilation direction in
the vertical shaft can be reversed [such as in a fire emergency condition] water spray protection as outlined
above is needed both above and below the shaft station for 10 hydraulic diameters.)
Example: Using Equation 2 for Hydraulic Diameter (Dh) in Section 2.2.1.2, for a shaft dimension of 10 20 ft
(3 by 6 m), Dh = 13.3 ft (4 m). Therefore the special deluge protection needs to extend 133 ft (40 m) above
for upcast ventilation (or below, if ventilation is downcast) each shaft station where ignition sources are
present.
Where sprinklers are needed they should preferably be of an open nozzle type designed in rings around
the inner perimeter of the shaft and sprinklers should be spaced horizontally on lines and vertically so that
all surfaces are properly wet. A minimum density of 0.25 gpm/ft2 (6 mm/min) should be provided. Detection and
actuation should be by heat, smoke, light, or electrical resistance-type thermal wire actuated devices. Note
that smoke or particle counting type detectors may be sensitive to false alarm due to dust or fuel exhaust
fumes common in or near shaft stations and may not be suitable.
Sprinklers should also be provided within the shaft station to protect against ignition sources such as diesel
fuel and within horizontal drifts connecting into the shaft station if timber lined.
Fig. 3. Sketch of shaft and shaft station fire protection system (combination water spray and smoke detection) developed
by the US Bureau of Mines. The system was demonstrated full scale in an underground metal mine to function properly.
c) An alternative to sprinklers in the shaft is to cover the wood liner with a sprayed on cementitious coating
such as gunnite or shotcrete. The wood liner should not be covered with a foamed plastic covering.
d) If the FPI is less than 7 no special fire suppression protection is needed for the shaft based on the lining
itself, although the shaft station may still need sprinklers if used to move or stage combustible materials.
7-12
17-17
Page 16
5. Provide FM Approved small (112 in) hose stations with at least 250 ft (76 m) of hose and fed by a water
supply at each shaft station.
6. Provide FM Approved portable multi-purpose hand held extinguishers in every hoist cage that carries
personnel and/or supplies and at each shaft station.
7. Provide combustible or flammable liquid piping that extends downward via the vertical shaft (to feed, for
example, underground diesel fuel tanks) with automatic shutoff valves controllable from a central control
point and from each shaft station. Provide a shutoff valve at each shaft station and at the top of the shaft.
Consider a means of detecting pipe breakage or leakage within the shaft. If possible, do not maintain flammable liquid transfer pipes with a permanent liquid head; empty pipes after gravity transfer.
8. Provide a fire retardant coating or other protection on grouped electrical cables with combustible polymeric
insulation that enter underground mines via a vertical shaft if fuel loading and arrangement is considered
unsatisfactory based on Data Sheet 5-31, Cables and Bus Bars.
9. Provide automatic fire doors (mine stoppings) at the entrance into horizontal drifts from shaft stations,
where timber sets or timber and wood lining are present in the drifts, station, or shaft. Arrange doors to close
on heat, smoke or carbon monoxide gas (CO) detection (or a combination of these detectors) and rate doors
at two hours resistance.
2.2.4 Underground Belt Conveyors
Rubber or synthetic plastic belt conveyors underground may be required by code to be rated as fire retardant,
notably in underground coal mines but occasionally in metal/non-metal mines.
Some fire retardant rated belts have been shown by losses and FM Global Research testing to be capable
of self sustained fire spread. International belt testing protocols do not always accurately or technically measure potential for fire spread and many belts manufactured cannot be considered true non-fire propagating
under many fire conditions encountered underground.
Currently only the FM Global Research FPI test is acceptable in this document to determine conveyor belt
fire propagation potential.
Refer to Data Sheet 7-11, Belt Conveyors, for protection guidelines on conveyors and for a description of
FM Global Research FPI testing protocol and protection guidelines.
1. For best protection and where economical, provide sprinklers along the entire length of all underground
rubber or other polymeric material based belt conveyors whether fire retardant rated or not. Refer to Data
Sheet 7-11, Belt Conveyors, and use guidelines for totally enclosed systems.
2. Where sprinklers are not practical, use a non-propagating conveyor belt that has been tested for FPI and
listed as Class I by FM Global Research.
As an alternative to full sprinkler protection or use of an FM Global listed Class I belt underground use the
following minimum guidance to limit damage and control ignition sources:
3. Protect important production* belt conveyors running in narrow, inaccessible** noncombustible tunnels
per guidelines in Data Sheet 7-11, Belt Conveyors, for totally enclosed systems. This generally means full
sprinkler protection the entire length of the beltway.
* A production belt is one that is considered critical for continued ore extraction from the mine. There may
be local belt conveying systems that can be bypassed by other belt systems or by mobile equipment that
will reduce or eliminate production downtime. These non-critical belts may not need protection (other than
ignition source control) if not in an area where they expose other combustibles such as wood timber sets.
Conversely, the main belt that delivers ore to the surface can almost always be considered critical to
continued production.
** An inaccessible tunnel is a tunnel, drift or passageway which does not lend itself to ingress for fire fighting equipment or vehicles. Narrow tunnels or drifts, often only slightly larger than the belt system, may
be used to connect larger tunnels.
4. Protect important production belt conveyors running in tunnels or passageways which are accessible*
for manual fire fighting with automatic sprinklers over drive motors, end pulleys, or other known or common
friction or ignition points or sources. Extend sprinklers 50 ft (15 m) beyond in both directions and space at
7-12
17-17
Page 17
10 ft (3 m) intervals on lines. Design sprinkler activation to sound an alarm at a constantly attended location
and shutdown the conveyor system.
* An accessible tunnel is a tunnel which is large enough to permit easy entry of fire fighting equipment
and response personnel alongside the beltway and one that has manual fire fighting equipment such as
well spaced fire hose stations. It also requires that the fire response team is trained in conveyor belt fire
fighting, will respond with water hoses within 10 minutes, that the ventilation flow can be controlled, and that
the responders have appropriate emergency gear such as self contained breathing apparatus (SCBA).
5. For all other belts not considered critical to production, provide smoke or heat detection over drive motors,
pulleys, or other known friction or ignition points or sources. Extend detectors 50 ft (15 m) beyond in both
directions from the ignition source and space at 20 ft (3 m) intervals on lines. Arrange detectors to sound an
alarm at a constantly attended location and shutdown the conveyor system. Note that smoke or particle
counting type detectors may be sensitive to false alarm due to dust or fuel exhaust fumes common in or near
conveyor beltways. Electric resistance type line detectors have been effectively used underground.
6. Interlock all underground conveyors to shut down and alarm on slippage, friction, misalignment, and
mechanical ripping.
7. Follow all other guidelines for ignition control and protection as covered in Data Sheet 7-11, Belt Conveyors
8. Provide FM Approved small [112 in. (38 mm)] hose stations at 250 ft (76 m) intervals along accessible
conveyor systems. Design fire hose stations based on Data Sheet 4-4N, Standpipe and Hose Systems. Carry
fire hose and water supply on emergency response vehicles for inaccessible areas.
2.2.5 Underground Explosives and Blasting Agents
1. Protect explosives and blasting agents used for mineral removal in accordance with Data Sheet 7-28,
Energetic Materials. Protect bulk ammonium nitrate, prior to being mixed with other ingredients to produce
blasting agents (such as ANFO), in accordance with Data sheet 7-89, Ammonium Nitrate and Mixed Fertilizers
Containing Ammonium Nitrate. Also refer to local mine regulations.
7-12
17-17
Page 18
2. Certify employees or contractors who supervise or conduct blasting on a mine site for the type of blasting
agents and blasting procedures used.
2.2.6 Underground Service and Utility Areas
1. Provide safeguards for air compressors, transformers, pumps, electrical switchgear, emergency
generators, motors, cooling systems and other service and production machinery located underground per
the appropriate FM Global Data Sheet for similar aboveground operations. Increase frequency of maintenance and testing when harsh conditions underground such as dust, vibration, moisture, etc.) exist. (Refer
to Section 2.2.1, Miscellaneous Exposures to Continued Mine Production, for a more detailed description of
critical utility systems in underground mines and reference to several appropriate data sheets)
2. House important underground utility and fixed service equipment, especially electrical systems and
equipment, in environmentally tight enclosures or otherwise separate when sensitive to exposure from dust,
vibration, moisture, diesel fuel fumes, vehicle impact, etc.
3. Provide automatic sprinklers backed by an adequate water supply in underground service and utility equipment areas where concentrations of combustibles such as lubricating and hydraulic oils are used or stored
or combustible timber sets and lagging or connecting wood walkways are present. Base the need for
sprinklers on the same conditions as applied aboveground, using values, economics, manual fire fighting
ingress, and exposure to other equipment or areas as a guide.
From a purely property damage and production impact standpoint, sprinklers are generally only economical
in larger rooms with major concentrations of combustibles, high value equipment, and/or high business interruption exposure. When equipment is scattered in smaller rooms subdivided by rock or other noncombustible
partitions, sprinklers are generally not economical.
Where sprinklers are not provided nor needed, provide products of combustion detection to give early warning
for low value or limited exposure areas.
When deemed needed, conform sprinkler systems as much as practical to those recommended for
aboveground installations.
2.2.7 Underground Warehousing
There are normally no large or high piled warehousing facilities in underground mines. Spare parts and
supplies are normally stored in small storage areas up to 10 to 15 ft (3 to 4.5 m) high due to mine back height
restrictions. Storage may be in racks or solid piled. However, all types of commodities could be present,
including plastic components and packaging. Many such small storage areas may exist.
1. Protect warehouse storage of mixed commodities per guidelines in data sheets in the 8 Series, where
economics and values warrant. Generally automatic sprinklers are needed for fire control or suppression when
values or exposure warrant.
2. Provide FM Approved Small (112 in. 38 mm) fire hose stations near underground warehousing areas.
Design fire hose stations based on Data Sheet 4-4N, Standpipe and Hose Systems.
2.2.8 Underground Handling and Storage of Flammable Liquids
There is no limit to the amount or flammable or combustible liquids allowed in underground mines as long
as they are properly segregated and protected. From a risk standpoint, it is often better to store well protected
bulk quantities underground than to frequently transfer liquids from the surface. Transfer activities are
inherently more susceptible to release of liquids than storage systems due to the process of making and
breaking connections.
Flammable and combustible liquids may be delivered to the underground working by pipeline or in portable
tanks, in drums, or in smaller FM Approved containers. Bulk storage of liquids is usually confined to diesel
fuel or lube oils for mobile equipment. Much lesser quantities of solvents or paints are kept underground.
1. Protect flammable and combustible liquids in underground mines similar to surface facilities using Data
Sheet 7-29, Flammable Liquid Storage in Portable Containers; Data Sheet 7-32, Flammable Liquid
Operations; and Data Sheet 7-88, Storage Tanks for Flammable and Combustible Liquids. Apply guidelines
for piping and transfer, mixing, storage, small container transfer, and ignition source control.
7-12
17-17
Page 19
Fig. 5. Underground diesel fueling station. Station is in a rock enclosure but due to rock fall potential the rock enclosure
has been supported by wood planks on steel beams and columns. This room has a sprinkler system over the fueling area.
2. Do not permit use of Class IA flammable liquids in underground mines. Substitute Class IA flammable
liquids with less hazardous liquids. (Note: most international country codes do not allow use of Class 1A liquids
underground.)
3. Avoid use of plastic tote bins for transport or storage of combustible or flammable liquids underground.
Use FM Approved transport containers wherever possible.
4. Provide an automatic fire suppression or control system for flammable and combustible liquids storage
and transfer areas. Acceptable systems are automatic sprinklers, packaged AFFF or high expansion foam
systems, and packaged dry chemical or gaseous suppression systems if rooms are properly enclosed and
tight. Refer to data sheets 4-0, Special Protection Systems; 4-1N, Water Spray Fixed Systems; 4-7N, Low
Expansion Foam Systems; 4-10, Dry Chemical Systems; and 4-11N, Carbon Dioxide Extinguishing Systems
for guidelines for systems other than standard sprinklers.
5. Provide fire resistant partitions rated at one hour between flammable and combustible liquids storage or
handling and other occupancies or separate the areas by physical space from important occupancies. If
space separation is used, establish at least 100 ft (30 m) of open area without combustible storage or
occupancy or wood timber sets. Natural rock partitions are acceptable and often preferable.
6. Provide FM Approved small (112 in. 38 mm) fire hose stations near underground storage areas or
flammable and combustible liquids handling areas. Design fire hose stations based on Data Sheet 4-4N,
Standpipe and Hose Systems.
2.2.9 Underground Handling and Storage of Compressed Gases
1. Limit the amount of compressed gases stored underground to the minimum needed for practicality.
Measure storage limitations against the increased hazard of frequently transporting cylinder of flammable
or hazardous gas from the surface.
7-12
17-17
Page 20
2. Use the guidelines in the following FM Global data sheets for protection of compressed gas cylinder
storage and handling:
Data Sheet 7-50, Compressed Gases in Cylinders.
Data Sheet 7-51, Acetylene.
Data Sheet 7-52, Oxygen.
Data Sheet 7-56, MAPP Industrial Gas.
3. Prohibit the use of compressed liquefied petroleum gases (LPG) such as propane in underground mines.
4. Provide FM Approved small (112 in. 38 mm) fire hose stations near underground storage areas of
flammable compressed gases. Design fire hose stations based on Data Sheet 4-4N, Standpipe and Hose
Systems.
2.2.10 Underground Mobile Equipment
Mobile equipment underground may consist of loaders, haulers, jumbo drills, shotcreting units, rock bolting
machines, blast hole loaders, personnel vehicles, etc. Diesel fueled mobile equipment with rubber tires are
normally used in metal/non-metal mines. Electrically propelled equipment are commonly used in coal mines
and some non-metal mines due to similarity of mining equipment to coal. Rail mounted equipment may also
be used.
Longwall excavators, usually used in soft deposits such as coal and potash, are very large and critical pieces
of equipment. While often electric powered, they feature large hydraulic systems for supporting the mine
back during mining and caving.
Fully integrated tunnel boring machines that can bore up to 23 ft (7 m) in diameter are exceptionally high
value equipment with electrical cables and hydraulic and lubrication oil systems.
7-12
17-17
Page 21
Fig. 7. Drawing of diesel fueled excavator with special suppression system in engine compartment.
1. Protect important underground mobile or excavating equipment as it is protected on the surface, using
Data Sheet 7-40/13-27, Heavy Duty Mobile Equipment. Base protection on value and production importance.
2. Protect important equipment with hydraulic fluid systems using Data Sheet 7-98, Hydraulic Fluids.
3. Do not park or stage mobile equipment using combustible fuels or oils for hydraulics and lubrication in
areas identified as noncombustible zones for fire purposes (see section 2.2.2, Wood Timber Sets in Drifts and
Tunnels).
4. Protect underground mobile equipment maintenance facilities with automatic sprinklers and FM Approved
112-in. (38 mm) fire hose stations where values, production importance, or exposure to other important areas
warrant.
5. Follow guidelines for aboveground bucket wheel excavators, draglines, stacker-reclaimers, etc. for unique
or critical, non-spared underground equipment such tunnel boring machines and longwall excavators. Refer
to Section 2.3.1, Surface Mobile Equipment, for guidelines for large and critical production equipment and
the need for non-destructive analysis testing, maintenance, and inspections.
6. Where practical provide spares of critical long-lead time parts or components on large excavation equipment and provide a documented contingency plan to quickly obtain parts off-site (such as by participating
in a global parts-pool, for example).
2.2.11 Underground Fire Water Supplies and Distribution Systems
1. For new mines, where values and economics warrant, design fire protection water supply using appropriate
aboveground fire protection guidelines for adequacy and reliability. Refer to Data Sheet 3-2, Water Tanks
for Fire Protection and Data Sheet 3-7, Fire Protection Pumps.
2. For existing mines fire protection water supply for sprinklers or hose stations may be from dedicated fire
water systems or domestic or process water systems if nearby fire protection water is not economically
available. Generally, gravity systems are used underground fed from sump tanks.
Sometimes due to extreme elevation differences, staged tanks are used at many levels and pressure reducing
valves may be needed. Refer to Data Sheet 3-11, Pressure Reducing Valves for Fire Protection Service.
Use considerable judgement in determining equivalent reliability for water supply and distribution systems
underground.
3. Do not exceed maximum pressures feeding sprinkler systems of 175 psig (11.9 barg) to assure proper
waterspray distribution and pattern.
7-12
17-17
Page 22
4. Preferably, loop fire water distribution mains underground allowing an adequate water source from at
least two directions, in the event one feed direction is damaged due to fire induced rock fall. Provide sectional
shutoff valves approximately every 3000 ft (915 m) on main lines and at every lateral main feeding branches
to working areas or sprinklered rooms or equipment. Proper placement of divisional shutoff valves will allow
emergency responders to access systems based on ventilation flow direction. Electrically supervise all valves
on fire protection systems underground to assure proper open position.
5. Protect underground water distribution mains, where exposed in tunnels and passageways, against mobile
vehicle impact, rock fall, earthquake (where appropriate in FM Global 50-year through 500-year earthquake
zones as shown in Data Sheet 1-2, Earthquakes), and freezing.
2.2.12 Combustible Ores in Underground Metal and Non-Metal Mines
Some underground metal or non-metal mines have concentrations of high sulfide-content (HSC) ore or may
have regions of coal or other combustible fossil materials. Wet HSC ores have been known to spontaneously
ignite in pockets which are not accessible to manual fire fighting, yet creating smoke and gas levels in
working areas sufficient to interrupt production or cause mine evacuation. Explosions have also occurred
in HSC ore dust clouds liberated during blasting or drilling operations, creating severe underground damage.
Similar incidents can also occur in localized coal deposits which are incidental to the metal mining operation.
1. Identify and document the presence of HSC ores or coal deposits susceptible to spontaneous heating
or blast induced dust explosions using modern geotechnical and analytical techniques.
2. When HSC ore bodies or coal deposits have been identified as having spontaneous heating potential,
continuously monitor the deposits using carbon monoxide analyzers to give advance warning of combustion. Develop and document administrative procedures in advance to cope with a deep seated HSC ore or coal
fire. Procedures might include fire fighting techniques and emergency passageway sealing techniques.
3. When it has been identified that drilling or blasting may take place within or loosen HSC ore bodies or
nearby coal deposits, and that dust explosions might occur, implement previously developed preventive
measures. Preventive measures might include, but are not limited to, using continuous water sprays on drilling
bits to minimize dust formation and friction ignition; water mist inerting of the entire blast zone; using
powdered limestone as drill hole grout to pleghmaticize (inert) the combustible dust; and sealing off the area.
2.2.13 Naturally Occurring Flammable Gases in Underground Metal and Non-Metal Mines
Some underground metal or non-metal mines may have concentrations of naturally occurring methane or
other flammable gases such as carbon monoxide or hydrogen sulfide (caused by deep seated combustion
processes) that may be present due to nearby coal deposits or other organic materials in the geologic
structure being mined. Ignition of concentrations of such gases that are within their explosive limits can cause
underground damage even if thousands of feet (meters) distant. Even if in unmined deposits, gas can seep
into working areas. Mines with known or potential flammable gas deposits are called Gassy Mines.
1. Identify and document the potential presence of methane or other flammable gases by modern geological
and analytical techniques.
2. When methane or other flammable gases have been identified within a metal mine, continuously monitor
ventilation flow using FM Approved combustible gas detectors to give advance warning of a change in concentration that may enter the explosive range. Place detectors in ventilation systems and arrange to sound
an alarm at 10 ppm concentration in air. Concentrations over 100 ppm are considered significant trends and
should be dealt with immediately. A CO/CO2 ratio analysis can also be effectively used. Develop administrative procedures in advance to understand the mines gas liberation trends and characteristics; acceptable
limits of gas formation; and methods to respond to adverse gas buildup such as proper ventilation control
or passageway sealing techniques. Refer to Data Sheet 5-49, Gas and Vapor Detectors and Analysis
Systems.
3. Use permissive (intrinsically safe) electrical equipment in mines identified as gassy.
7-12
17-17
Page 23
2.2.14 Collapse, Cave-ins, Rock Falls and Rock Bursts in Underground Metal and Non-Metal Mines
Collapse (or cave-in) can involve localized or widespread sections of a mine. A rock fall is usually very
localized. A rock burst occurs when a hydraulically or geologically stressed section of rock essentially blows
out into the tunnel environment causing local damage and far ranging overpressure effect due to air pressure
down tunnels.
The science and technology of minimizing or preventing collapse of mines, rock bursts or localized rock falls
from mine backs is well established and dependent on the geology and structure of the mine and ore body
and external effects such as vibrations from blasting or equipment and from seismic events. Experts
determine the need for various roof and mine support systems. Roof support can vary from using mining
techniques such as room and pillar to providing localized rock bolting, shotcrete or timber sets.
1. Determine the need for and type of roof support or ore extraction methods by an expert in ground support.
2. Consider the use of rock motion detectors to determine need for and adequacy of roof support in known
unstable or highly stressed ground.
3. Protect important or critical fixed utility or production equipment from cave-in by rock bolting systems or
structures. Do not locate important equipment in areas known to be subject to stressed rock bursts.
4. Identify, document, and monitor highly stressed rock subject to sudden and violent rock bursts through
the life of the mine.
5. Avoid or significantly restrict the use of wood timber sets and wood lagging to prevent collapse or rock
falls in new mines and properly protect timber sets where installed in older mines. (Refer to Section 2.2.1.1,
Wood Timber Sets in Drifts and Tunnels)
6. Assume that polymeric structural support materials (such as expanded isocyanurate foam structural
systems), even if rated fire retardant, are combustible and capable of self sustained fire propagation unless
they have been tested and approved for the installation by FM Approvals. Remove such materials or coat
with a FM Approved fire retardant material.
2.2.15 Ventilation Systems for Fire Control
Underground ventilation systems can be effectively used for fire control as well as environmental control.
Ventilation can have an effect not only on oxygen content (and thus the potential for fire growth or suppression)
but also on the ability of emergency teams to effectively access a fire source.
1. Design underground ventilation systems as part of the overall fire response and control protocol. Preferably
retain a specialist in underground fire growth and suppression during new mine development to model
simulated fire scenarios and provide input into ventilation design and the mine emergency plan.
2. Design ventilation systems to be operable from a central control room. If the control room might be
inaccessible during a fire emergency, the ventilation system should also be controllable from aboveground.
3. Arrange ventilation to be reversible so that emergency responders may approach an underground fire
from more than one direction and from the upstream ventilation flow direction.
4. Develop, document, and update emergency response procedures at least annually based on use of
ventilation to control or suppress underground mine fires. Use of computerized mine ventilation models and
simulations is encouraged. Revise the emergency plan when changes are made that may effect ventilation
flow (such as addition of mine stoppings or new tunnels).
2.3 Surface Mining Operations
2.3.1 Mobile Equipment at Surface Mines and Ship Loading Facilities
1. Protect self propelled mobile equipment including large draglines, power shovels, haulage trucks, water
trucks, and front end loaders which use flammable or combustible fuels, hydraulic fluids, oil lubricating
systems, and combustible cabling or wiring per Data Sheet 7-40/13-27, Heavy Duty Mobile Equipment.
2. Protect large, high value stationary, mobile, or semi-mobile bulk handling equipment such as earthmovers,
cranes, draglines, stackers, reclaimers, stacker-reclaimers, tripper-stackers, scraper-reclaimers, bucket
wheel excavators, continuous loaders, and shiploaders as follows:
7-12
17-17
Page 24
Fig. 8. Self propelled 190 ton (172 tonne) ore haul truck.
a) Protect flammable or combustible fuels, hydraulic fluids, oil lubricating systems, and combustible
cabling or wiring per Data Sheet 7-40/13-27, Heavy Duty Mobile Equipment.
b) At a minimum, protect against windstorm, collapse, toppling, metal failure, improper operation and
maintenance, fire, and earthquake according to Data Sheet 1-62, Cranes.
c) Take special care in initial design and construction of this critical and high value equipment to assure:
an adequate and technically accurate design standard was used during manufacture; end use conditions
were known and conditions of potential overload or stress were determined, documented, and operators
trained; and design audits were conducted during manufacture of the machine to assure design intent is
met.
d) Conduct a risk assessment on all existing equipment to: identify potential hazards and failure modes;
analyze the overall risk; quantify and rank the risk; and provide corrective action.
e) Place key mobile or semi mobile equipment on a reliability based maintenance, non-destructive examination (NDE) schedule to detect metal fatigue and potential for premature cracking or other mechanical
failures.
f) Identify highly stressed areas on this type of equipment using working drawings or by consultation with
the manufacturer and subject to NDT (e.g., magnetic particle) in their heat affected zones to ensure they
are crack free. After initial start-up testing and examination, repeat this test at intervals not exceeding
7 years for machines less than 20 years in service. For machines with more than 20 years service and
others of suspect condition and initial design or where operation is in a corrosive environment (such as a
saltwater shiploader), conduct the NDE test every 5 years at a minimum.
g) Subject this equipment to a full visual internal and external examination by the manufacturer, an
accredited manufacturer representative, or an independent consultant proficient in this type of equipment and work at least every three years for the first 20 years, and every two years thereafter. This will
allow for trends analysis and ensure the machine is satisfactory for the duties it is intended to perform.
h) Conduct life evaluation studies (e.g., finite element analysis [FEA]) after 25 years of trouble-free service,
or sooner if significant design changes have been made which may compromise their integrity during
normal operations or in an overload condition. FEA should be comprehensive and the scope of work should
7-12
17-17
Page 25
include: machine condition; life expectancy; opportunities for increased performance if desired; balance
of machine; condition of critical structures (e.g., masts and booms); and condition of mechanical devices
(e.g., bucket wheel shafts). The report should be comprehensive, identify areas where fatigue life is
consumed, and state with confidence that potential overloading situations have not been created by
changes. Conduct FEA in conjunction with a good visual examination and measurement of operating
conditions using strain gages.
2.3.2 Explosives and Blasting Agents at Surface Mines
1. Protect explosives and blasting agents used for mineral removal in accordance with Data Sheet 7-28,
Energetic Materials. Protect bulk ammonium nitrate, prior to being mixed with other ingredients to produce
blasting agents (such as ANFO), in accordance with Data sheet 7-89, Ammonium Nitrate and Mixed Fertilizers
Containing Ammonium Nitrate.
2. Certify employees or contractors who supervise or conduct blasting on a surface mine site for the type
of blasting agents and blasting procedures used.
2.3.3 Belt Conveyors at Surface Mines
1. Protect cross country and captive conveyor systems per Data Sheet 7-11, Belt Conveyors.
Fig. 9. Large excavating shovel loading a haul truck, in a hard rock open pit mine.
7-12
17-17
Page 26
7-12
17-17
Page 27
7-12
17-17
Page 28
7-12
17-17
Page 29
3. Design sprinklers, when needed, based on the predominate occupancy hazard in accordance with Data
Sheet 3-26, Fire Protection Water Demand for Non-Storage Sprinklered Properties or occupancy-specific
data sheets, and install in accordance with the rules in Data Sheet 2-0, Installation Guidelines for Automatic Sprinklers. Use dry pipe systems in unheated areas except where discharge of air might create dust
explosion hazards, such as in dry coal areas. In these cases, preaction or deluge sprinkler systems are preferable.
4. Provide surface ore and coal processing sites with a dedicated fire protection system with an adequate
and reliable water source, a properly valved and sized underground main distribution system, and standard
fire hydrants or monitor nozzles. Space hydrants at approximately 250 to 300 ft (76 to 91 m) intervals. Base
adequacy and reliability of water supplies for fire protection on demands presented in Data Sheet 3-26, Fire
Protection Water Demand for Non-Storage Sprinklered Properties, and/or the appropriate occupancy data
sheet for the hazard being protected, and Data Sheet 2-0, Installation Guidelines for Automatic Sprinklers.
Fire water distribution mains should preferably be located underground. Exceptions include permafrost
regions where mains may be located abovegrade in steam traced boxes, or in tropical regions where they
may be located aboveground on pipe racks. In all cases fire water distribution systems should be protected
from freezing, mobile equipment impact, and other exposures (such as land subsidence, flood, etc.) where
such exposures exist.
5. Provide standpipes with hose connections at all operating levels of ore processing and storage buildings in accordance with Data Sheet 4-4N, Standpipe and Hose Systems. Assure equipment includes
FM Approved 112 (38 mm) hose with spray nozzles and connections for 212 in (635 mm) hose. In unheated
areas arrange standpipes on manual or dry pipe systems.
6. Protect general site flammable and combustible liquids storage and handling areas using:
7-12
17-17
Page 30
7-12
17-17
Page 31
Fig. 16. Partially covered captive conveyor system feeding crushed ore from primary crusher to ore bin, zinc mine.
9. Evaluate core sample storage to determine production, business or financial criticality of the samples. If
the samples are considered critical and a loss (fire, collapse, flood, landslide, etc.) could cause the cores
to become damaged or mixed (rendering them unusable), protect the sample storage or building accordingly.
7-12
17-17
Page 32
Where cores are critical and stored in wood or cardboard trays or in a combustible building provide automatic
sprinklers, relocate to a noncombustible facility, or replace combustible trays with noncombustible trays.
Fig. 17. Core storage facility. Cores are stored in wood boxes in metal racks. While the value of the boxes, rocks, and
racks have little value, the data contained in the rock cores might be critical to longterm mining operations.
7-12
17-17
Page 33
Fig. 18. Outdoor ore stockpile with an open, elevated conveyor system feeding ore from a nearby rushing facility. Ore is
reclaimed by a conveyor system located in a tunnel underneath the pile, visible at lower left.
2. Provide automatic sprinklers or (if water supplies are not available) a local automatic fire suppression
system (such as foam, carbon dioxide or other gaseous system, or dry chemical system) over hydraulic and
lubrication oil systems used for ore reclaim equipment where production impact warrants. Refer to Data Sheet
7-98, Hydraulic Fluids, for additional protection needs.
3. Provide protection for grouped electrical cables in ore storage facilities per Data Sheet 5-31, Cables and
Bus Bars.
4. Protect high sulfide content (HSC) ores stored outdoors against water penetration (that may promote
oxidation and spontaneous combustion) and rotate the pile based on coal piles outlined in Data Sheet 8-10,
Coal and Charcoal Storage.
5. Protect large ore reclaim or stacking equipment associated with ore piles and bins as outlined in detail
under Section 2.3.1 for mobile, stationary, and semi-mobile equipment at surface mining operations.
2.4.4 Ore Concentrator Plants (Mills)
Ore concentrator facilities generally have predominantly noncombustible construction, although very old mills
may have wood construction and some newer plants are using rigid plastic wall panels. Isocyanurate based
plastic foams may be used for tank freeze protection or corrosion resistance of structural steel in areas where
acids or other corrosive reagents are in use.
The combustibility of the occupancy varies by facility and process but processing areas may have extensive
internal rubber or plastic lining of equipment, plastic trommels, screens and rubber chutes, rubber conveyor
belts, rubber or plastic pipe and hose, combustible lubrication and hydraulic fluids, thermal oils, flammable
and combustible reagents and solvents, oil filled transformers, and grouped electrical cables. Thus, while the
machinery and product may be noncombustible, significant combustible loading may exist in localized areas.
Recommendations in this section on concentrating mills should also be applied to similar areas in coal
preparation plants, floating dredges, or other mineral processing facilities.
7-12
17-17
Page 34
Fig. 19. Simplified process flow diagram of a typical metal ore concentrator plant.
7-12
17-17
Page 35
Fig. 20. Rubber lined pipes from four separate grind circuits feeding a common rubber lined tank.
Fig. 21. View of interior of multi-grind circuit concentrator plant. Much of equipment and piping shown has rubber linings.
7-12
17-17
Page 36
b) Provision of manual gate valves at key places in grind circuit rubber lined piping that can be closed
during maintenance operations or that can be closed by operators during a fire emergency.
c) Provision of special mill-use or fire water connections to key RLE that may be manually opened to
flood a dry RLE system during a fire emergency
3. For existing facilities, explore opportunities to change rubber lining to noncombustible liners.
4. For existing facilities, where adjacent grind circuits have common connections of RL piping or equipment,
investigate opportunities to separate the circuits. Where separation can not be achieved, provide gate valves
at the common point (such as at a head or thickener tank) on each pipe leading back to a grind circuit. Clearly
mark these valves and close these valves during maintenance activities when the system is shut down or dry.
Assure that closure of these valve is part of any hot work permit systems and part of an emergency preplan.
Also provide normally closed, permanently fixed connections to process water systems where the exposure
and economics warrant. Generally these connections are mounted on the side of pipes or vessels such that
water flows by gravity into the system. They are intended to be opened only during a fire emergency to flood
the internal system and should be well labeled as to use and location.
5. When present, clearly identify and label rubber lined equipment by placards or stenciling on the side of
the rubber lined vessel or pipe. Assure that the label indicates that internal rubber lining is present and that
hot work such as cutting and welding be avoided.
6. When possible completely prohibit, by management policy, hot work for equipment with rubber linings.
Use an alternative form of repair. When hot work must be done, incorporate the following provisions into the
activity:
a) Provide explicit wording in the mine hot work permit system regarding RLE. Provide a check off on
the permit as to the presence of RLE within enclosed equipment or within open tanks below a hot work
operation where hot slag may fall and precautions to be taken during the work activity, such as closing gate
valves.
7-12
17-17
Page 37
7-12
17-17
Page 38
Fig. 25. Warning label hanging on pipe located directly above an open topped rubber lined tank.
7-12
17-17
Page 39
b) Assure that personnel conducting hot work on enclosed RLE or above open vessels with rubber lining
receive special hazard awareness training on rubber liner fires.
c) Cover or flood with water open tanks or openings below hot work operations and station personnel
with charged hose near the exposed vessels.
7. Ensure that the on-site fire brigade or fire department has a written pre-plan in place for emergency
response to each process area having RLE. This may include pre-planned options such as flooding the
systems with process water, shutting selective isolation valves between equipment or adjacent grinding
circuits, providing the ability to break apart piping, cooling external equipment with fire hose, etc., as well as
being prepared for excessive smoke generation and concealed fire spread. Knowledge of the extent and
location of RLE is of utmost importance in emergency response which ties closely to labeling of equipment
and knowledge of the continuity of rubber liners.
8. Where numerous side-by-side rubber lined open tanks or other open vessels are located in a discrete
area of the plant, provide automatic sprinklers at ceiling level over the tank area to prevent tank-to-tank fire
spread when tanks are dry. As an alternative to sprinklers, when rubber lined open tanks are to be temporarily
removed from process service, fill the tanks with water to prevent accidental interior ignition during
maintenance operations such as cutting and welding above the tank.
9. Assure that repair or modifications to interiors of rubber lined equipment are done using the following
precautions:
a) Use safety solvents where possible
b) Use FM Approved safety cans for flammable solvents.
c) Provide adequate safety ventilation when using flammable solvents to prevent accumulations or
pocketing of vapors inside of tanks.
d) Minimize ignition sources. Provide proper electrical equipment for hazardous locations when working
inside enclosed systems with electrical fixtures (such as lights), per Data Sheet 5-1, Electrical Equipment
for Hazardous (Classified) Locations.
e) Provide FM Approved portable fire extinguishers or charged fire hose for immediate use.
2.4.4.2 Belt Conveyors
1. Provide rubber belt conveyors located inside concentrator facilities with automatic sprinklers and
appropriate shutdown interlocks using Data Sheet 7-11, Belt Conveyors, as a guideline.
2.4.4.3 Flotation Reagents
1. Segregate and protect combustible, flammable, or reactive liquid reagents such as activators in flotation
or other ore beneficiation processes in accordance with Data Sheet 7-32, Flammable Liquid Operations.
Where quantities are sufficient, provide an automatic water or AFFF foam sprinkler system over the storage
and distribution area and provide appropriate drainage based on Data Sheet 7-83, Drainage Systems for
Flammable Liquids. See Table 2 for some common flotation reagents, trade names, and flammability
characteristics. Note that there are hundreds of reagents and only a sample is presented below. Some are
received as solids but may be dissolved in combustible or flammable liquids such as alcohols, or the powder
may be combustible or explosive.
Table 2. Common flotation reagents.
Reagent
Xanthates (Potassium Ethyl Xanthate,
Sodium Isobutyl Xanthate, Sodium
Isopropyl Xanthate, Potassium Amyl
Xanthate)
Mercaptobenzothiozole
Trade Names
Dow Z Series
AeroXanthate 300 series
Fire Hazard
Inorganic powders, No fire hazard, but
may be dissolved in flammable solvents at
plant
7-12
17-17
Page 40
Reagent
Thionocarbanilide
Trade Names
AeroCarbanilide 130
Pamak
Pamolyn
Actinol
Pamak 25
Actinol D6LR
Alamine, Armeen, Arosurf,
Amine, Alamac
Aero Promoter 800 Series
Pyronate
Aerol 100 series
Aero Depressant 600 Series
Burtonite 78
Guartec
Jaguar
Depramin Series
Lignosite
Marasperse
Orzan
Various Brands
Red Floc
Dextrin
Various
Fire Hazard
Organic combustible powder. Powder may
explode. Mixtures take on flammability
characteristics of the solvent carrier
FP > 300F (150C)
Various
FP 105F (41C)
Yarmor F
Fuel oil
GNS No. 5
Teefroth
Dowfroth 200 series
Ucon Frother
Minerec F2000 Series
Aerofroth 65
Aerofroth 70 Series
Nalco 8836
Ucon Frother
Various
Various
(Varies by grade)
FP > 300F (150C)
Combustible alcohols
FP varies by type
See MSDS Sheets
Various weights and flash points. All
weights are combustible liquids
FP > 300F (150C)
FP 100 to 150F
(38 to 66C)
None
2. Preferably, store bulk storage of combustible, flammable, or reactive reagents in properly diked and
arranged outdoor tank farms rather than inside concentrator plants. Refer to Data Sheet 7-88, Storage Tanks
for Flammable and Combustible Liquids, for spacing and other protection guidelines.
3. Where a gravity tank (usually located at a high point in the building) is used for flammable reagent transfer
to cells, provide an automatic shutoff valve (interlocked to a thermal sensor) at the outlet of the tank. Locate
the reagent tank in a dike or larger concentric tank capable of holding the entire contents. Do not use plastic
7-12
17-17
Page 41
7-12
17-17
Page 42
Fig. 26. Drums of flammable cleaning solvent being used to clean gear teeth of large SAG mill in copper concentrator.
7-12
17-17
Page 43
2. For unusually high production, monetary value, or long lead time electronic switchgear, marshalling
cabinets, Programmable Logic Controller (PLC) enclosures, or motor starter sets with solid state circuitry
and significant internal combustible polymeric components, install a packaged automatic gaseous suppression system inside the units cabinet. As an alternative to internal protection provide a spare component on
site. This latter alternative is valid only if one cabinet of important electrical component can be involved in a
single fire incident.
3. Where grouped plastic insulated electrical power or instrumentation cable concentration or arrangement
within MCC rooms, in cable spreading areas, in general plant areas, under floors of control rooms, in
subgrade tunnels, or outdoors near transformers or switchgear rooms is sufficient, provide special protection based on Data Sheet 5-33, Cables and Bus Bars. This may include such options as automatic water or
gaseous based suppression systems, fire retardant coatings or coverings, physical separation of trays, or
encapsulation of trays in noncombustible containment systems. Give special attention to locations where
cables are exposed to other combustible materials such as near oil filled transformers or flammable reagent
areas and for long vertical runs of cable tray in high bay buildings. Where cable trays are located below areas
where hot work is common, cover the cable trays with noncombustible shields.
4. Seal vertical or horizontal openings between adjacent rooms or upper levels with electrical cable trays
with a 1 hr fire barrier material to prevent room-to-room spread. Consider compartmentalization of unusually
large MCC or cable spreading areas into smaller rooms. Consider subdividing long vertical runs of cable
trays with barriers.
5. Use a less flammable insulating oil such as silicone based fluids for indoor transformers, where possible.
Preferably locate combustible oil insulated transformers outdoors in special fenced and drained areas. If
located indoors, base need for automatic sprinkler on protection guidelines in Data Sheet 5-4/14-8,
Transformers. Also follow these protection guidelines for large oil filled outdoor transformers.
6. Drain and flush indoor transformers of more than 100 gal (0.38 m3) capacity using Polychlorinated
Bi-Phenyls (PCB) insulating fluids and follow guidelines in Section 2.6 of Data Sheet 5-4, Transformers.
7-12
17-17
Page 44
Fig. 28. Concentrator plant MCC room with high value marshalling cabinets and grouped electrical cables at the ceiling.
7. Spare important large or long lead time transformers or other electrical equipment.
7-12
17-17
Page 45
8. Where dusty conditions exist, locate highly sensitive electric or electronic equipment in pressurized rooms
or enclosures. Provide proof of pressurization with alarms to warn of failure.
9. For additional protection guidelines for important electrical equipment, including electrical maintenance
and testing, refer to the following FM Global data sheets:
Data Sheet 5-18, Protection of Electrical Equipment
Data Sheet 5-19, Switchgear and Circuit Breakers
Data Sheet 5-20, Electrical Testing
Data Sheet 5-24, Miscellaneous Electrical Equipment.
Data Sheet 5-32, Electronic Data Processing Systems
Data Sheet 7-45, Instrumentation and Control in Safety Applications
2.4.4.9 Control Rooms
1. Install, protect, and maintain programmable logic controllers (PLC), computer systems, marshalling
cabinets, and associated equipment, used for control of entire concentration processes (e.g., grinding or
flotation circuits) or specific equipment (e.g., SAG mill) as recommended in Data Sheet 7-45Instrumentation
and Control in Safety Applications, and Data Sheet 5-32, Electronic Data Processing Systems. In many cases
room or equipment flooding suppression systems are needed for these critical systems. At a minimum, install
products of combustion detection in electronic control rooms and seal the rooms against dust and processing
fumes.
2.4.4.10 Fuel Fired Process Equipment
1. Protect fuel fired process equipment such as roasters, calciners, rotary kilns, ovens, and dryers using:
Data Sheet 6-7/12-7, Fluidized Bed Combustors and Boilers
Data Sheet 6-9, Industrial Ovens and Dryers
Data Sheet 6-10, Process Furnaces
Data Sheet 6-17/13-20, Rotary Kilns and Dryers
2.4.5 Powerhouse and Utilities
1. Protect powerhouse and other utility or site support systems, such as cooling towers, emergency power
systems, compressed air systems, on site oxygen production, etc. in accordance with FM Global recommended practices as applicable:
Data Sheet 1-6, Cooling Towers
Data Sheet 6-2/12-63, Pulverized Coal Fired Boilers
Data Sheet 6-4/12-69, Oil- and Gas-Fired Single-Burner Boilers
Data Sheet 6-5/12-70, Oil- or Gas-Fired Multiple Burner Boilers
Data Sheet 5-3/13-2, Hydroelectric Power Plants
Data Sheet 5-4, Transformers
Data Sheet 5-19, Switchgear and Circuit Breakers
Data Sheet 5-23, Emergency and Standby Power Systems
Data Sheet 5-13, Synchronous Motors
Data Sheet 5-17, Large Electric Motors
Data Sheet 7-35, Air Separation Processes
Data Sheet 7-95, Compressors
7-12
17-17
Page 46
Fig. 29. Diesel fueled generators providing sole source electrical power at remote gold mine. (Courtesy Rio Tinto)
2. Do not site new dams used for hydroelectric power generation above processing and mining operations
unless an engineering study demonstrates that the site cannot be impacted by water flow from a sudden
and catastrophic dam failure.
3. Study existing dams used for hydroelectric power generation, where located above processing and mining
operations, for potential flooding of the mine site should the dam or impoundment fail. Assure that this study
includes an evaluation of dam design and stability under various worst case scenarios (including earthquake,
wave action, erosion, terrorism, etc.) by a registered professional engineer or equivalent. Provide diversion
chutes below the dam if conditions warrant.
2.4.6 Emission and Waste Control
1. Protect site waste or emission control systems in accordance with FM Global recommended practices
as applicable:
Data Sheet 7-78, Industrial Exhaust Systems
Data Sheet 7-73, Dust Collectors and Collection Systems
Data Sheet 6-11, Fume Incinerators
Data Sheet 6-13/12-13, Waste Fuel-Fired Boilers
Data Sheet 1-13, Chimneys
Data Sheet 7-48, Disposal of Waste Materials
2. Provide automatic sprinkler protection for important bag houses where bags or material being collected
is combustible.
3. Provide automatic sprinklers for the interior of electrostatic precipitators where construction or materials
are combustible. Refer to Section 2.4.9 for additional guidance on plastic equipment.
7-12
17-17
Page 47
Fig. 30. Haulage truck inside high bay mobile equipment shop.
1. Where the ceiling of the bay above the mobile equipment is 60 feet (18 m) or less provide standard wet
or dry pipe automatic sprinklers on a system designed to provide 0.45 gpm/ft2 (18 mm/min) over 5000 ft2
(12 mm/min over 460 m2) (wet pipe) or 8000 ft2 (740 m2)(dry pipe) using 165F (75C) heads.
2. Where the ceiling of the bay above the mobile equipment is greater than 60 feet (18 m), tailor protection needs to the local conditions by conducting a risk analysis. Protection options might include but are not
limited to:
a) Provision of ceiling mounted zoned deluge sprinklers, one zone for each truck or locomotive bay,
actuated by optical detectors positioned underneath or near the bottom sides of the vehicle.
b) Provision of automatic foam or water deluge monitor nozzles mounted near the sides of the vehicle
designed to rapidly throw foam under the truck or locomotive. These may be mounted on nearby structural
building columns.
7-12
17-17
Page 48
3. Regardless of ceiling height, where the vehicle or locomotive has a concealed subgrade space underneath the vehicle, where fuel or lubricants are constantly present or capable of being released into the space,
and where the ceiling sprinklers will not be effective, provide water or foam sprinklers for the space and
concealed vehicle surfaces subject to BLEVE (such as fuel tanks).
4. In all cases, provide FM Approved small (112 in. 38 mm) hose stations in garages and locomotive
refueling and maintenance shops for fast incipient response.
5. Provide means to pull a burning vehicle or multiple vehicles from adjacent work bays under emergency
conditions.
6. Maintain and inspect incoming vehicles to assure tires are not overheated or other imminent ignition or
fuel release sources are not present.
7. Eliminate combustibles, especially oil soaked rags, from areas between truck bays and keep areas clean
of spillage of oils or lubricants. Rags should be stored in special receptacles and frequently disposed of to
prevent spontaneous ignition.
8. Consider prohibiting refueling of locomotives indoors. Where refueling of locomotives is done indoors,
interlock fuel delivery lines to be quickly shutoff in the event of fire. Fully explore other opportunities for
reducing amount of diesel fuel involved in a fire such as drainage, reducing pipe sizes and pump capacities,
eliminating gravity feed systems, etc.
2.4.8 Hydro-metallurgical Mineral Solvent Extraction (SX) Processes
2.4.8.1 Design new SX plants using principles of Inherent Safety. Refer to DS 7-43, Loss Prevention in
Chemical Plants.
2.4.8.1.1 Space and locate SX plant process and utility buildings, solvent areas, and storage tanks based
on a risk assessment that considers radiant heat from pool fires, solvent drainage patterns, wind effects, and
emergency response capability.
2.4.8.1.2 Design buildings, piping systems, process tanks, and other vessels using noncombustible or fireresistive construction. Use steel or concrete where possible. Where plastic tanks or piping are unavoidable, use a structural plastic, such as fiber reinforced plastic (FRP), instead of a thermoplastic, such as
polyethylene or polypropylene, which is subject to softening and premature failure under fire exposure. Do
not use glass piping systems.
2.4.8.1.3 Eliminate or reduce below-grade spaces for tank farms, piping, and process equipment. Locate
all facilities at the same grade.
2.4.8.1.4 Eliminate or reduce the use of sub-grade trenches for solvent piping systems. Locate pipes above
grade on accessible and well-ventilated pipe racks.
2.4.8.1.5 Do not use rubber flexible couplings on solvent lines and pumps. Where flexible couplings are
required, use steel.
2.4.8.1.6 Lower roofs and covers on tanks and process vessel to minimize the vapor-collection space above
liquid surfaces.
2.4.8.1.7 Use seal-less or mechanical double-sealed pumps for solvents.
2.4.8.1.8 Use methods to reduce static and organic mist generation in solvent systems, such as submerging in-feed nozzles, minimizing bends and restrictions in piping, reducing solvent flow velocities, and using
low-turbulence pumps.
2.4.8.1.9 Separate process control and safety interlock instrumentation from power cables. Route instrumentation for safety shutdown systems well away from solvent areas.
2.4.8.1.10 Use additives that lower the resistivity of the solvent to minimize or eliminate the potential for static
electricity generation.
2.4.8.2 For all new and existing SX facilities, provide fire detection and fire suppression as follows:
2.4.8.2.1 For large outdoor SX complexes (of the type and size typical to copper or uranium extraction featuring circuits of side-by-side SX buildings) provide automatic deluge water spray and/or AFFF foam-water
protection systems as indicated below:
7-12
17-17
Page 49
a) Inside under the cover or roof of mixer-settler (M-S) buildings or cells to protect the solvent pool, using
either water or foam-water systems
b) Inside solvent or organic storage tanks that are of production importance and/or that are located within
production areas and potentially expose other production equipment, using an AFFF system with foam
delivery chambers
c) Around the external perimeter of plastic or wood constructed organic solvent tanks using an automatic open head water-only deluge system
d) Over solvent or organic transfer pumps using either water or foam-water systems
e) On or under elevated pipe racks carrying flammable solvents or organics in plastic pipes using either
water or foam-water systems
f) Over launders, troughs and wiers attached to M-S cells, using either water or foam-water systems
g) Inside pipe trenches with plastic pipes carrying flammable solvents or organics, using either water or
foam-water systems
h) Inside dikes enclosing solvent storage tanks when located within process areas, using a foam chamber delivery system.
i) Around the exterior perimeter of M-S cells or buildings if spaced closer than 50 ft (15 m) from each
other, as water curtain exposure protection from nearby cells or buildings. Use standard automatic closed
head or deluge water-only sprinklers.
j) As exposure protection for other critical equipment (such as transformers) or outside along important
building walls (such as MCC rooms) that are within 50 ft (15 m) of a solvent fire area. Use standard automatic closed head or deluge water-only sprinklers as exposure protection.
k) If the roof of an M-S cell is more than 10 ft (3 m) above the solvent pool use AFFF foam-water discharge chambers along the sides of the pool to ensure faster pool fire suppression.
l) Actuate deluge or AFFF foam-water systems using a high speed detection system. In the specific case
of pipe trenches, elevated pipe racks, and cable trays, use thermal or electrical resistivity detection wire.
7-12
17-17
Page 50
Fig. A. Close-up of mixer-settler building with protection using foam water chamber at surface of solvent in upper view,
and deluge waterspray or foam water at ceiling in lower view. In both cases protection is also provided over troughs and
launders and inside trenches with plastic pipes carrying solvents.
Fig. B. Protection for building walls (external water curtain) and tank farm details
2.4.8.2.2 For smaller outdoor SX plants (with multiple banks of side-by-side small plastic cells of the type
and size typical to lithium, nickel, iodine, etc.) provide automatic water or foam-water deluge sprinklers over
the top of the entire cell bank. Provide internal water or foam-water protection for the interior of individual
cells when there is an avenue for internal fire spread from cell to cell. See Figure C, for an example of the protection layout.
7-12
17-17
Page 51
Fig. C. Outdoor, small-cell SX facility with deluge waterspray over and under vessels and foam inside vessels.
2.4.8.2.3. For indoor SX processes, provide protection at the ceiling of the building housing the process,
under large equipment such as raised solvent tanks, under grated or solid intermediate mezzanines, inside
cells or tanks that have covers common to other process cells or tanks, or where openings into closed cells
or tanks may allow the spread of an exterior fire into the tank.
Fig. D. Indoor SX plant with deluge waterspray at ceiling, over mixer-settlers, under grating, under vessels, and foam inside
vessels. Note flexible rubber couplings on pipes connecting cells.
2.4.8.2.4. Where vertical process columns (such as pulsed columns) are used for solvent extraction or recovery, protect in accordance with DS 7-14, Chemical Process Structures. Where pulsed columns are constructed of FRP or other structural plastic rather than steel, additional protection might be needed.
7-12
17-17
Page 52
Fig. E. Pulse columns with flammable organic solvents. Used in uranium and some copper extractions. Example of deluge fire protection.
2.4.8.2.5. Protect the surface of open mixer-settler ponds located outdoors using automatic foam chambers along the sides of the tank to ensure fast foam delivery. For completely open ponds that do not expose
adjacent ponds or important production processes, a manual AFFF foam delivery system is acceptable if
emergency response capability is satisfactory.
2.4.8.2.6. Design water-only sprinklers to deliver 0.25 gpm/ft2 (10 mm/min) density over an operating area
of 4000 ft2 (370 m2) using high-temperature heads or 6000 ft2 (560 m2) using low-temperature heads. Provide a minimum water supply duration of 120 minutes.
2.4.8.2.7. Design AFFF systems using conventional delivery nozzles to deliver 0.16 gpm/ft2 (6.4 mm/min).
Ensure foam supply is available for 20 minutes.
2.4.8.2.8. Design AFFF systems using foam delivery chambers to deliver 0.10 gpm/ft2 (6.4 mm/min). Ensure
foam supply is available for 20 minutes.
2.4.8.3 Provide high-speed, early warning fire detection, such as IR or UV detection systems (or a combination of both), overlooking solvent tanks and pumps, inside enclosed mixer-settler buildings and in pipe
trenches. Use thermal wire detection in piperacks or cable trays. Ensure detectors actuate fire suppression
systems where installed.
2.4.8.4 Provide standard hydrants with hoses and monitor nozzles around and within SX plants spaced per
industrial spacing guidelines and DS 3-10, Installation of Private Service Mains and their Appurtenances.
Arrange monitors in solvent areas for manual AFFF foam injection. Use a demand of 500 gpm for 100 minutes for hose streams.
2.4.8.5 Locate bulk storage tanks of flammable or combustible solvent outdoors in a diked area per guidelines for flammable liquid tanks in Data Sheet 7-88, Storage Tanks for Flammable and Combustible Liquids. Ensure they are in separate rooms or diked areas separated from process equipment or utilities.
2.4.8.6 Provide solvent extraction process areas with minimum 6 in. (150 mm) high curbing to confine and
channel solvent spills. Ensure individual curbed areas do not exceed 5000 ft2 (460 m2).
2.4.8.7 Provide emergency drainage to a remote catch basin or pond from all diked areas and pipe trenches.
Design flow and storage capacity based on guidelines in Data Sheet 7-83, Drainage Systems for Flammable Liquids.
7-12
17-17
Page 53
Fig. F. Sketch of recommended placement of UV/IR light detectors inside typical copperuranium SX settler building and
inside sub-grade trenches designed to actuate protection systems and sound alarm
2.4.8.8 Use an emergency scuttling system for large M-S cells, whereby operators can remotely open automatic valves and quickly discharge cell contents to a safe area in an emergency.
2.4.8.9 If drainage cannot economically be provided where needed, use AFFF foam-water protection systems instead of water-only suppression systems.
2.4.8.10 Ensure solvents at upper levels of a process plant cannot flow to lower levels, spreading the fire
and increasing damage.
2.4.8.11 Where trenches or plastic piping enter a lower-grade tank farm or pumping area, provide a wall or
dike to prevent spilled liquids at the higher level from flowing into the lower area. Where plastic piping passes
though this dike or wall, provide a steel spool pipe for 10 ft (3 m) in the uphill direction, and an emergency,
remotely actuated shutoff valve on the line (see Fig. G).
2.4.8.12 Provide mechanical ventilation per FM Global standards for enclosed process buildings taking suction from near floor level when required, based on solvent flammability characteristics.
2.4.8.13 Provide an automatic interlock to stop flow of solvents in the event of operation of any fire protection system. Interlock the fire detection system to shut off solvent pumps. Provide an automatic shutoff valve
on Pregnant Liquor Supply (PLS) feed lines to prevent gravity overflowing of solvent tanks when pumps stop.
Provide manual shutdown capability usable from an accessible location.
2.4.8.14 Restrict hot work in solvent areas when solvent is present or where FRP or rubber-lined tanks are
present and empty. Follow special precautions, including use of a permit system and a combustible gas
detector, whenever hot work must take place near, on, or above such installations. Take special care during plant shutdown when plastic tanks may be dry and open.
2.4.8.15 Protect against static electricity buildup and discharge.
2.4.8.15.1. Evaluate and correct solvent piping systems with high flow velocities that produce static discharge. Where non-conductive solvents are used with plastic piping systems provide a conductive internal
pipe liner (such as carbon) to dissipate static charges generated by liquid flow. Bond and ground the system, including at flanges. (A non-conductive fluid is one with a conductivity less than 250 pS/m).
7-12
17-17
Page 54
2.4.8.15.2. Bond and ground flammable solvent systems, vessels, pipes, and pumps. Ensure bonding is provided across plastic or rubber sleeves in metal piping systems.
2.4.8.15.3. Submerge or lower solvent feed pipes where they enter solvent pools (such as inside a mixersettler) to minimize static discharge from free-falling flammable liquids and to minimize solvent mist development.
2.4.8.15.4. Inspect piping for gypsum or crud (also called jarosite) buildup or other non-conductive inorganic coatings that might compromise conductive liners. Clean accumulations to ensure conductivity.
2.4.8.15.5. Refer to DS 5-8, Static Electricity, for additional guidance and protection requirements.
2.4.8.16 Provide electrically classified electrical equipment as required by DS 5-1, Electrical Equipment in
Hazardous (Classified) Locations.
2.4.8.17 Provide general area lightning protection for buildings and solvent processing areas as recommended for local conditions and per local codes. Refer to the following publications for reference:
a) NFPA 780, Standard for the Installation of Lightning Protection Systems
b) IEC 61024, Protection of Structures Against Lightning
c) IEEE Std 142, IEEE Recommended Practice for Grounding of Industrial and Commercial Systems
7-12
17-17
Page 55
2.4.8.18 Operate the plant under a process safety management (PSM) system. Refer to DS 7-43, Loss Prevention in Chemical Plants, for details on implementing an effective PSM program.
2.4.8.19 Conduct process hazard analysis (PHA), such as a Hazop, on all new and existing SX plants. Conduct a revalidation PHA every five years and during major changes.
2.4.8.20 Manage all changes using a Management of Change (MOC) protocol.
2.4.8.21 Ensure housekeeping is of the highest order in solvent areas. Promptly clean up solvent spills or
mist accumulations. Repair leaks at pumps and flanges.
2.4.8.22 Develop procedures for overseeing contractors and for preparing sites for work. Ensure vessels
are drained into safe areas. Develop procedures to safely drain lines and vessels, when required.
2.4.8.23 Label tanks having combustible construction, such as plastic or rubber linings, as to combustibility.
2.4.8.24 Refer to Data Sheet 7-32, Flammable Liquid Operations, for additional guidelines on protecting
flammable/combustible liquid pumping and piping systems.
2.4.9 Plastic Equipment
1. Wherever possible in new construction, minimize or eliminate the use of plastic for equipment and duct
systems. Where used, provide fire retardantcy using antimony trioxide or the like, including in chemical liners
inside ducts or equipment. (Note: fire retardant additives are effective in retarding ignition but are much less
effective in retarding fire spread, especially on the interior of duct systems. Sole reliance on fire retardant
additives for fire protection is generally not effective.)
2. Follow all precautions under rubber lined equipment for labeling and ignition source control for plastic
equipment.
7-12
17-17
Page 56
3. Provide automatic sprinkler protection for concentrations of important plastic equipment located inside
buildings. Design the system to provide 0.30 gpm/ft2 (12 mm/min) coverage under solid floors or intermediate
mezzanines and 0.15 gpm/ft2 (6 mm/min) under intermediate open grated mezzanines. Extend protection
20 ft (6 m) in all directions beyond the equipment. In some cases protection might also be warranted for the
interior of indoor plastic ducts or large vessels. Conduct a risk assessment based on Data Sheet 7-78,
Industrial Exhaust Systems to determine need and extent of internal protection.
4. Provide directional water spray protection for important plastic equipment and ductwork located outdoors
based on a risk assessment. Focus on concentrations where large ducts cross over each other or multiple
vessels are positioned side-by-side. Design the system to provide 0.15 gpm/ft2 (6 mm/min) density over the
exterior surface area of coverage. For very large duct and vessel systems outdoors, use of automatically
controlled monitor nozzles may provide equivalent protection to fixed waterspray systems. Protection might
also be warranted for the interior of outdoor plastic ducts or large vessels. Conduct a risk assessment based
on Data Sheet 7-78, Industrial Exhaust Systems to determine need and extent of internal protection.
5. Do not allow combustibles to be stored or combustible enclosures or buildings to be staged or constructed
under outdoor FRP exhaust or gas cleaning systems. If possible restrict fueled vehicles from being parked
or from routinely being driven under these systems. Do not allow mobile molten metal or slag movers to pass
directly under plastic duct or vessels and provide barriers against accidently spilled molten materials to
prevent them from flowing into the exposed area. Label duct clearance to avoid vehicle impact.
2.4.10 Head Frames and Mine Hoists
Exposure to unprotected hoist cables from lubricating or hydraulic oil system fires inside head frames and
wire rope fatigue or mechanical damage have caused cables to fail, allowing hoist cages or skips to drop into
deep mine shafts. Fires have also occurred around and in pits underneath hoist motors where oil has been
allowed to accumulate.
Mechanical failure of hoist drums, hubs, spokes, drive shafts, and gears have occurred. Large synchronous
electric drive motors have failed. Resultant damage and production downtime has been extensive due to
such incidents.
Note that hoist motors and head frames can be located underground as well as aboveground.
1. Preferably, build new head frames of noncombustible or of fire resistive construction.
2. In head frames of combustible construction or occupancy, provide automatic sprinkler protection at every
level. Design sprinklers based on Table 8 in Data Sheet 3-26, Fire Protection Water Demand for Non-Storage
Sprinklered Properties.
3. Limit ordinary combustibles and storage of lubricating and hydraulic oils inside head frames and hoist
houses to immediate needs. Ensure that housekeeping, especially in cable oiling areas is of the highest order.
Do not allow excess oil spillage or overspray from oil systems, especially in pits or inaccessible areas, to
accumulate.
4. Give special attention to protection of hoist cable lubricating and hydraulic (braking) oil systems. These
are commonly located at the top level of head frames but may also be located at intermediate levels or in the
hoist motor room. Provide the following protection for these systems regardless of building construction:
a. Where possible, use FM Approved less hazardous fluids for hydraulic braking systems.
b. Provide automatic sprinklers at the ceiling over and for 20 ft (6 m) beyond combustible oil systems.
Design sprinklers at the ceiling should to provide 0.25 gpm/ft2 (10 mm/min) density over the area.
c. Provide automatic sprinklers inside demisters or other enclosed oil lubricating or braking equipment
which have oil accumulations or overspray and through which cables pass.
d. As an alternative to part 3, provide a special extinguishing system inside oil demisters or other enclosed
cable oiling equipment. Use a FM Approved carbon dioxide, dry chemical, or a gaseous suppression system.
e. When an approved less hazardous fluid is used for the hydraulic braking system and the system is cutoff vertically or horizontally by at least one hour walls/floors from lubricating systems, sprinklers are not
needed unless warranted by the presence of combustible construction or ordinary combustibles.
7-12
17-17
Page 57
5. Provide an automatic interlock to stop circulation or pumping of oil or hydraulic fluids in the event of operation of any fire protection system. This can be accomplished by interlocking oil pumps, valves in key lines,
etc. Provide a manual shutdown capability, useable from an accessible location. Arrange alarms to sound in
a constantly attended location upon activation of the protection system.
Fig. 34. Wire rope oiling system using sprayer enclosure and demister box.
6. Provision should be made through administrative controls or interlocks to shut off the hoist system after
a reasonable time during a fire emergency involving the hoist cables. The most suitable time can be determined by analysis of cable overheating potential without lubrication and the time needed to allow orderly
evacuation of employees inside hoist cages.
7. Protect large synchronous motors associated with hoisting operations (usually located in nearby detached
hoist houses) per Data Sheet 5-13, Synchronous Motors. Provide sprinklers in hoist drive motor houses
when construction or occupancy such as oil lubrication systems are combustible.
8. Refer to Data Sheets 7-98, Hydraulic Fluids and 7-37, Cutting Oils for additional guidelines on combustible
oils and fluids.
9. Conduct an initial baseline non-destructive examination (NDE) on all mechanical hoist components (drums,
hubs, spokes, drive shafts, brakes, and gears, etc.).
10. Following the baseline study, where no evidence of defects (cracking, etc.) have been found, perform
subsequent NDE at least every three years.
11. Where defects are found and repairs have been made, conduct NDE annually for at least the next three
years until trends indicate the frequency can safely be restored to three years.
12. Where a cracked component is made of cast iron, do not use weld repairs. For repair of cast iron
components, use cold mechanical repairs. (Older drum hoists are commonly constructed of cast iron).
7-12
17-17
Page 58
13. To determine the existence of cracking in mine hoist brakes, perform visual inspections as indicated in
Figure 36 (areas A-D). If thick layers of paint are present on brake components, obscuring possible cracks,
use magnetic particle inspection as the best NDE option. If paint needs to be removed to inspect brakes, avoid
use of shot blasting or solvents, which can further seal or obscure cracks.
14. Following large disturbances (such as flooding, earthquake, heavy rains, unusual blasting vibration, earth
subsidence, etc.), inspect and repair hoist alignment and foundations (i.e., fastener looseness, cracking,
damaged grout, spalling, etc.) prior to start up of the hoist system.
15. Use the following frequencies for general hoist component inspections under normal operating conditions:
a) Hoist alignment every three years
b) Foundation condition daily
c) Fastener tightness- quarterly
16. Refer to the related following data sheets for additional guidance on inspections of mechanical equipment:
Data Sheet 1-62, Cranes
Data Sheet 10-3, Hot Work Management
Data Sheet 13-1, Cold Mechanical Repair
Data Sheet 17-1, Nondestructive Examinations
17. Refer to Data Sheets 5-13, Synchronous Motors and 5-17, Large Electric Motors, for guidance on
mechanical and electrical inspections of hoist drive motors.
7-12
17-17
Page 59
7-12
17-17
Page 60
9. Have experts develop strict heap leach operating procedures and assure that employees are trained in
and follow operating procedures.
2.4.12 Electrowinning and Electro-refining
1. For new facilities, construct electrowinning and electro-refining cells and tanks of noncombustible
construction such as stainless steel or concrete. Where economical, replace combustible polypropylene
plastic cells in existing plants with stainless steel or other corrosion resistant noncombustible material.
2. Where plastic, rubber lined steel, or wood cells or tanks are present provide automatic sprinkler protection at ceiling level designed to 0.20 gpm/ft2 (8 mm/min) over 3000 ft2 (320 m2) (wet pipe) or 3500 ft2 (330 m2)
(dry pipe) with high temperature rated heads.
3. Where flammable or combustible solvents are used in the electrolytic process follow recommendations
for solvent extraction plants, Section 2.4.8.
4. Label plastic, rubber lined steel, and wood cells and tanks with placards or stenciling as to construction
and combustibility.
5. Avoid hot work on or near plastic, rubber lined steel, or wood cells and tanks. When needed use a hot
work permit system and take precautions similar those recommended for rubber lined equipment,
Section 2.4.4.1.
6. Refer to Data Sheet 7-6, Heated Plastic and Plastic Lined Tanks, for additional guidelines for plastic
electrowinning and electro-refining cells.
7-12
17-17
Page 61
7. Where corrosivity of the process requires protection of building structural steel, avoid use of foamed-inplace plastic or other highly combustible corrosion coverings. When it is uneconomical to remove these
materials, cover them with a FM Approved fire retardant coating and label as to combustibility.
2.4.13 Tailings Ponds
1. For design and siting of new tailings ponds and dams use the following guidelines. Where possible and
economical (especially where high value property exposures or business interruption potentials exist), also
use these guidelines for upgrading existing tailings piles:
a) Retain a certified specialist proficient in soil mechanics to design tailings dams or evaluate existing
dams. In earthquake-prone areas, retain a registered specialist in earthquake dynamics and soils
liquefaction.
b) Conduct complete geologic and hydrologic studies, including underground water and soil analysis at
the proposed tailings dam site location.
c) Ensure that foundation and construction soils investigations include, but not be limited to, grain size
and distribution, density, permeability, shear strength, moisture content, and plasticity.
d) Do not construct a new pond or dam over or near old mine workings, water bearing geological faults,
outcrops, near major flood or surface water runoff routes or below landslide or avalanche-prone areas.
Where such siting is desired, provide special runoff diversion chutes or upstream impoundments. Do not
construct new dams at an elevation higher than ore processing, utility, or mining facilities unless a dam
failure is assured by engineering evaluation to not impact the downstream manufacturing facilities.
Construct downstream diversion chutes or impoundments as needed.
e) Do not construct foundation or starter dams with permeable clay-type materials, or where the material
is in shear and subject to saturation or ground shaking induced liquefaction.
7-12
17-17
Page 62
f) Ensure that the possibility of earth tremors and liquefaction caused by sonic or other forces is considered in new design. Investigate the possibility of foundation subsidence and the stability of surrounding
slopes. Evaluate and implement measures to prevent wave and wind erosion.
g) Design drain lines, filter blankets, and french drains from the dam for long term, maintenance-free,
non-plugging operation.
h) Design decant towers and collector lines for total saturated loading for compression, shear, and tension.
i) Do not allow piping or other structures to pass through the face of the dam or the dam foundation.
j) For unusually high dams, use cyclones to separate out coarser materials from the tailings for use as
dam and wall construction base.
k) Plant the slope of impounding embankments with vegetation to help long term stabilization. Where
vegetation cannot be sustained, use geologic cover materials, chemical agents, or dust palliatives.
2. Do not site new mining and ore processing facilities below existing tailings stacks, pads, or ponds, to
minimize the potential of flood damage should the stack or pond dam or wall fail.
3. Retain professional engineers or specialists to evaluate existing tailing stacks, pads or ponds to determine
stability and potential for failure from various natural scenarios including earthquake and sonic induced
liquefaction and unusual rain fall, surface water, or flood. Correct discovered deficiencies by engineering
design or dam/dike reinforcement.
4. Install piezometer or inclinometer devices in all tailings dams to measure ground water levels and pore
pressures and to detect stack movement and stability changes.
5. Where flood, surface water runoff, sudden ice melt (caused by volcanic or ground heating activity), or
avalanche runoff potentials present exposures to existing dams and ponds, provide permanent diversion
chutes, barriers, or interceptors such as upstream ponds or dikes.
6. Annually audit and inspect, using tailings pile specialists, the integrity of existing tailing ponds and dams.
Results should be documented and defiencies corrected in a timely fashion.
7. Have experts develop strict tailing ponds operating procedures and assure that employees are trained
in and follow operating procedures.
2.4.14 Production Pipelines
1. Protect cross country concentrated ore slurry or waste tailings pipelines against flood, avalanche, ice
flow caused by volcanic ground heating, landslide, subsidence, vehicle impact or excess weight and other
perils that may cause the pipe to break or be damaged. For very long pipelines, consider installing redundant,
well separated pipes to assure continued operation should one fail.
2.4.15 Cross Country Rail Lines
1. Protect cross country privately owned railway lines used to transport ore or concentrate to shipping ports
or remote processing plants against flood, avalanche, ice flow caused by volcanic ground heating, landslide,
subsidence, vehicle impact or excess weight and other perils that may cause the line, bridges or trestles
to break or be damaged. Consider installing two parallel rail lines in zones of severe exposure to assure
continued operation should one be damaged.
2. Inspect rail lines and bridges using third party specialists at least annually. On a monthly basis conduct
detailed line inspections using site personnel. Use a rail mounted vehicle to inspect the line for obstructions such as animals, snow, ice, or flooding, in advance of every train. Conduct non-destructive metal fatigue
analysis on samples of steel rails periodically.
3. Develop and document a post-incident contingency plan in the event the rail line is suddenly taken out
of service. Ensure that the plan includes alternate means of ore transport.
2.5 Surface Coal Preparation
The following recommendations are specific to the coal processing industry. General site and concentrator
plant recommendations in Sections 2.1 and 2.4 should also be applied where applicable.
7-12
17-17
Page 63
Fig. 37. Private cross country rail line for transporting iron ore from an inland area of Western Australia to a coastal port.
(Courtesy of Rio Tinto)
7-12
17-17
Page 64
5. Electrically classify coal processing buildings as follows under section 2.3.4.7, Ignition Source Control.
6. In areas where dry coal dust is present and a room explosion hazard exists, protect sprinkler piping, valves
and fittings against explosion damage as recommended in Data Sheet 7-14, Fire & Explosion Protection
for Flammable Liquid, Flammable Gas, & Liquefied Flammable Gas Processing Equipment and Supporting
Structures. Where sprinklers are installed in unheated areas with accumulated coal dusts, preferably design
the system to be deluge or preaction rather than dry pipe to avoid air discharge which could cause dust
liberation and subsequent explosion.
7. Follow guidelines for control rooms, plastic equipment and piping, rubber lined equipment, flammable
reagents, utilities, important equipment, etc. covered under metal concentrating plants (Section 2.4.4) for coal
preparation plants. Clearly label plastic pipes and equipment.
2.5.2 Thermal Coal Dryers
1. Install an automatic deluge water spray system inside fluidized bed and screen-type thermal dryers to
protect the constriction or screen deck against fire damage which could occur due to a hot spot or sudden
flare up. Place discharge nozzles so that they will effectively cover all portions of the top surface of the deck
7-12
17-17
Page 65
and design the system to provide a minimum density of 0.25 gpm/ft2 (10 mm/min) over the area of the deck.
Actuate the system by thermal detectors located inside the dryer set at 50F (10C) above the maximum operating temperature of the dryer.
A less desirable arrangement is to have the system arranged for manual actuation. This can be accomplished
by use of push button solenoid valves or manual control valves. Manual actuation is acceptable only if
actuators are in a constantly attended location, such as a control room, alarms are transmitted to the same
constantly attended location, and operators are trained and given the authority to activate the system.
Fig. 39. View of thermal dryer showing constriction deck and cyclone collection system.
2. For thermal dryers using heat transfer oil (e.g., thermal disc dryers):
a) Provide automatic sprinklers throughout the building and over pumps, tanks, filters, heaters, etc. where
hot oil is stored or could be released. Pay specific attention to protection of the interior of the dryer unit
which may be shielded from ceiling sprinklers. Design sprinklers to provide 0.25 gpm/ft2 (10 mm/min) over
the area of the building plus a 250 gpm (946 l/min) hose allowance.
b) Whenever possible, locate storage tanks and heaters of hot oil outside of the dryer building in specially
protected structures.
c) Provide fire or heat actuated shutoff valves at strategic points on the oil piping system to minimize
the amount of oil that could backflow in the event of breakage.
d) Refer to Data Sheet 7-99/12-19, Heat Transfer by Organic and Synthetic Fluids, for further information
and additional recommendations.
3. Provide automatic deluge water spray for the interior of collectors or cyclones into which dried coal dust
fines are discharged from the dryer. Pay special attention to internal portions of ducts which are susceptible
to accumulations of coal. Design the system to provide 0.25 gpm/ft2 (10 mm/min) density over the internal
surface area. When multiple cyclones or collectors are used, it is often preferable to have multiple small
deluge systems instead of one large system.
7-12
17-17
Page 66
Fig. 40. Sketch of recommended placement of deluge water spray systems for constriction deck and cyclones.
4. Provide combustion safeguards for all fuel fired thermal dryers per Data Sheet 6-2/12-63, Pulverized CoalFired Boilers, Data Sheet 6-9, Industrial Ovens and Dryers, or Data Sheet 6-24/13-21, Coal Pulverizers and
Pulverizing Systems, which ever is most appropriate.
5. In addition to combustion safeguards, discontinue fuel firing when:
a) High temperature exists in the dryer above the constriction or screen deck (screen and fluidized bed
dryers), in the drying chamber (flash dryers), in discharge ducts from the dryer, and in cyclones. Set
temperature sensors 50F (10C) above the normal operating temperature for the zone in question.
b) Process waterflow is lost to wet scrubbers which may be used to clean the coal dust laden air stream
prior to discharge to atmosphere. Conversely, design the system so that fuel cannot be fired prior to
scrubber water being in operation.
c) Internal fire protection water spray over the constriction deck operates.
d) Wet coal infeed into the dryer or dry coal outfeed from the dryer is suddenly stopped.
2.5.3 Coal Dust Explosion Protection
1. Preferably locate coal screening, crushing, and cleaning processes producing dry coal dust in open
structures. If not possible, provide buildings or rooms within buildings housing these type operations with
explosion venting in accordance with Data Sheet 7-76, Prevention and Mitigation of Combustible Dust
Explosions and Fires, and Data Sheet 1-44, Damage-Limiting Construction.
2. Provide thermal dryers which produce coal dust clouds as part of or incidental to the process with
emergency explosion venting, directed to outdoors. Base design Data Sheet 7-76, Prevention and Mitigation
of Combustible Dust Explosions and Fires.
7-12
17-17
Page 67
3. Air aspirate all indoor equipment handling dry coal dust (such as conveyor, housings, classifiers, etc.)
Alternatively, totally enclose and operate this equipment at a negative pressure relative to the environment
to minimize release of dust into the building.
4. Provide collection intakes at all points where dust can be liberated, such as at unloading stations, conveyor
transfer points, at classification equipment, in silo or bin galleries and tunnels, and in truck or rail loadout
stations.
5. Design and vent dust collectors in accordance with Data Sheet 7-73, Dust Collectors and Collection
Systems, and 7-76, Prevention and Mitigation of Combustible Dust Explosions and Fires. Locate dust collectors outdoors whenever possible and provide collectors with emergency explosion venting. If located
indoors, direct explosion venting to the outdoors by the shortest route possible using strong ductwork.
6. Do not reintroduce collected dust back into the coal stream within the plant except where this is an integral
part of the process, such as in a fluidized thermal dryer operation. Reintroduce captured coal fines only at
rail or truck loading stations.
7. Ensure that housekeeping and maintenance of equipment are of the highest order in coal handling areas.
Promptly remove spills of coal or accumulations of coal fines, preferably by vacuuming or water washing.
2.5.4 Methane Explosion Protection
1. For locations processing coal known (or suspected) to be high in combustible gas content, provide the
following protection for below grade or confined storage locations, such as silo interiors:
a) Combustible gas detectors designed to sound an alarm in a constantly attended location when the
concentration of methane in air exceeds 25% of the lower explosive limit.
b) Continuous mechanical ventilation designed to exhaust liberated gases to atmosphere. Design ventilation rate to keep the concentration below 25% of the lower explosive limit of the gas or gas mixture.
Arrange an alarm to sound in a constantly attended area should ventilation be shut off.
2.5.5 Ignition source control
1. Design electrical equipment in coal processing buildings for Class II, Division 1 or 2, in accordance with
Data Sheet 5-1, Electrical Equipment in Hazardous (Classified) Locations. Special electrical equipment is
not needed in the following areas:
a) Processing areas where coal is sufficiently wet to prevent airborne dust.
b) Plant areas, such as control rooms, electrical equipment rooms (i.e., motor control centers, transformer
vaults, etc.), and other rooms which are cutoff and ventilated and/or pressurized to prevent interior
accumulations of coal dust.
2. Design electrical equipment in areas prone to methane gas accumulation for Class I Division 1 in
accordance with Data Sheet 5-1, Electrical Equipment in Hazardous (Classified) Locations.
3. Monitor carbon monoxide (CO) gas formation, which is an early indicator of internal heating which could
lead to spontaneous combustion, using FM Approved combustible gas detectors inside long term coal storage silos, bins, and bunkers. Long term is defined as storage in residence more than one month.
4. Refer to Data Sheet 8-10, Coal and Charcoal Storage, for additional recommendations concerning control
of spontaneous heating of coal in storage bins.
5. Do not use space heating equipment in dry coal dust areas that have open flames or any exposed surface
at temperatures above 340F (171C).
6. Do not permit railroad locomotives or other vehicles which could ignite a dust cloud to operate within car
or truck loading/unloading buildings while a coal dust cloud is present. Provide Class II Group G front end
loaders and lift trucks routinely present in areas with coal dust clouds occupancies as described in Data Sheet
7-39, Industrial Trucks.
7. Preferably, restrict hot work from areas with coal dusts, potential methane accumulations, or near or over
plastic equipment. When needed, use a formal hot work permit system. Determine the presence of methane
or other combustible gases using a portable gas detector and eliminate the gas source or accumulation prior
to hot work.
7-12
17-17
Page 68
Fig. 41. Flow diagram of mining and mineral processing activities from exploration to product sales.
7-12
17-17
Page 69
4.0 REFERENCES
4.1 FM Global
Data Sheet 1-0, Safeguards During Construction
Data Sheet 1-1, Firesafe Building Construction and Materials
Data Sheet 1-2, Earthquakes
Data Sheet 1-6, Cooling Towers
Data Sheet 1-29, Wind Design
Data Sheet 1-9, Roof Anchorage
Data Sheet 1-13, Chimneys
Data Sheet 1-25, Process Tanks and Silos
Data Sheet 1-40, Flood
Data Sheet 1-44, Damage Limiting Construction
Data Sheet 1-54, Roof Loads for New Construction
Data Sheet 1-57, Plastics in Construction
Data Sheet 1-62, Cranes
Data Sheet 2-0, Installation of Automatic Sprinklers
Data Sheet 2-81, Fire Safety Inspections and Sprinkler System Maintenance
Data Sheet 3-2, Water Tanks for Fire Protection
Data Sheet 3-7, Fire Protection Pumps
Data Sheet 3-11, Pressure Reducing Valves for Fire Protection Service
Data Sheet 3-26, Fire Protection Water Demand for Non-Storage Sprinklered Properties
Data Sheet 4-0, Special Protection Systems
Data Sheet 4-1N, Water Spray Fixed Systems
Data Sheet 4-4N, Standpipe and Hose Systems
Data Sheet 4-7N, Low Expansion Foam Systems
Data Sheet 4-10, Dry Chemical Systems
Data Sheet 4-11N, Carbon Dioxide Extinguishing Systems
Data Sheet 5-1, Electrical Equipment for Hazardous (Classified) Locations
Data Sheet 5-3/13-2, Hydroelectric Power Plants
Data Sheet 5-4, Transformers
Data Sheet 5-7, National Electrical Code
Data Sheet 5-11, Lightning Surge Protection for Electrical Systems
Data Sheet 5-13, Synchronous Motors
Data Sheet 5-17, Large Electric Motors
Data Sheet 5-18, Protection of Electrical Equipment
Data Sheet 5-19, Switchgear and Circuit Breakers
Data Sheet 5-20, Electrical Testing
Data Sheet 5-23, Emergency and Standby Power Systems
Data Sheet 5-24, Miscellaneous Electrical Equipment
Data Sheet 5-31, Cables and Bus Bars
Data Sheet 5-32, Electronic Data Processing Systems
Data Sheet 5-49, Gas and Vapor Detectors and Analysis Systems
Data Sheet 6 Series, Boiler and Industrial Heating Equipment
Data Sheet 6-2, Pulverized Coal-Fired Furnaces
Data Sheet 6-4, Oil- and Gas-Fired Single-Burner Boilers
Data Sheet 6-5, Oil- or Gas-Fired Multiple Burner Boilers
Data Sheet 6-7, Fluidized Bed Combustors and Boilers
Data Sheet 6-9, Industrial Ovens and Dryers
Data Sheet 6-10, Process Furnaces
Data Sheet 6-11, Fume Incinerators
Data Sheet 6-13, Waste Fuel-Fired Boilers
Data Sheet 6-17, Rotary Kilns and Dryers
Data Sheet 6-24, Coal Pulverizers and Pulverizing Systems
Data Sheet 7-6, Heated Plastic and Plastic Lined Tanks
Data Sheet 7-11, Belt Conveyors
Data Sheet 7-13, Mechanical Refrigeration
Data Sheet 7-14, Fire + Explosion Protection for Flammable Liquid, Flammable Gas, + Liquefied Flammable
7-12
17-17
Page 70
7-12
17-17
Page 71
Lignite Coal: a brownish-black very soft coal in which the alteration of vegetal matter has proceeded further
than peat but not as far as sub-bituminous. Lignite coal is high in moisture and volatility and has a calorific
value less than 8,300 BTU/lb (19.3 Mj/Kg).
Concentrate: the valuable material produced from an ore by a separating or concentrating process
Dore (Pr: Door-Aay): a silver-gold alloy commonly formed at a gold mine site in bullion (bar) form. The
dore bar is sent offsite for separation and purification of the two metals. Dore is typically 70% gold and 30%
silver although these percentages can vary widely.
Footwall: wall or rock under an ore deposit
Fossil material: carbon based (organic) materials that were created in the earths crust due to fossil decay,
deposition, and pressure forces. Typical fossil materials that are exploited by mining are coal, petroleum
liquids, tar sands, natural gas and gas liquids, gilsonite, and oil shale.
Gangue: undesirable waste rock mined with valuable minerals in an ore body. Gangue is disposed of on
mine dump piles, as tailings, or used as fill for exhausted mine areas or it may be used for road building or
other construction purposes.
Gob: broken, caved, and mined-out (and often abandoned) portion of an ore deposit. Coal gobs are sources
of spontaneous heating.
Hard Rock: hard metallic ores (i.e., gold, copper, zinc, lead), non-metal aggregates (i.e., gravel), or structural
minerals (i.e., granite, marble). Hard rock mining is the extraction and processing of hard rock materials.
Coal and many non-metal materials such as salt, trona, and potash are considered soft rock materials and
their extraction soft rock mining.
High Sulfide Content (HSC) Ores: ore deposits containing high concentrations of pyritic or iron sulfide
compounds. HSC ores are subject to spontaneous heating and their dusts, when released and ignited by
conventional blasting, can explode violently. A sulfides content in excess of approximately 28% should be
considered explosive prone.
Lode: mineral deposit in solid rock.
Matrix: rock or gangue material containing ore minerals.
Metal mineral: belonging to the class of inorganic metal compounds which include gold, silver, copper,
tungsten, molybdenum, vanadium, tin, nickel, and lead. Some metals are found in pure metallic form
(e.g., gold, silver, tin, and copper) but most are found as oxide or sulfide ores in large but relatively low grade
quantities that must be further processed to recover the pure metal.
Mineral: a naturally formed inorganic substance occurring in the earths crust and having a consistent and distinctive set of physical properties and a composition that can be expressed by a chemical formula. While
the term mineral sometimes is used in reference to coal and other organic fossil based materials, mineral
in this document is used only for metal or non-metal compounds and not fossil materials.
Muck: mineral ore or waste rock that has been broken by blasting.
Non-Metal mineral: structural and industrial minerals. These non-fuel inorganic materials do not become metals by metallurgical processing. They are used as mined or are chemically processed into other non-metal
compounds. Examples of industrial non-metallics are trona, potash, asbestos, sulfur, barite, limestone,
abrasives, and salt. Examples of structural non-metallics are quarry products such as sandstone, marble,
granite and rock (sand and gravel) aggregates. Most gemstones fall in the non-metals mineral category.
Gemstones commonly occur in placer deposits.
Nugget: a small mass of native precious metal.
Ore: a mixture of valuable mineral and gangue waste rock
Orebody: natural concentration of valuable minerals that can be extracted and sold.
Overburden: undesirable, valueless material covering a valuable ore or coal deposit which has to be removed,
(usually by surface mining) to access the valuable deposits.
Pipe: vertical, narrow orebody usually formed in the throat of an ancient volcano or magma chute. Diamonds
are often found in pipes.
7-12
17-17
Page 72
Shoot: concentration of minerals; that part of a vein or zone that carries the valuable ore grades.
Vein: a well-defined tabular mineralized zone, which may or may not contain ore bodies.
Wash: barren rock or mineralized material that does not have enough value to be classified as ore
A.2 Mining Terms
Aerial ropeway/cableway/tramway: a system of cables or wire ropes suspended from towers or pylons from
which hang cages, buckets, or baskets for hoisting or transferring ore (and occasionally personnel) over
rough, steep terrain.
Adit/Drift/Entry: a horizontal entrance in a mine used to transport equipment and personnel and remove ore.
Drifts and adits are metal mine terms and entry is a coal term. An adit that is continuous through a mountain
and has two portals is a tunnel.
Afterblast: the after effects of a combustion explosion of methane underground where oxygen and steam
form as by-products of the explosion. The steam condenses to water, forming a partial vacuum which causes
an in-rush of air pressure into the mine.
Afterdamp (aftergases): mixture of gases remaining in a mine after a fire or explosion of combustible gases.
These gases, consisting primarily of hydrogen, carbon dioxide, and nitrogen inert the air and may prevent
effective emergency response.
Air blast: pressure wave of air passing down tunnels in a piston-like effect. It is caused by a sudden rock
fall (see burst or rock burst) or other disturbance such as a remote explosives discharge which pushes the
air at great force. The air burst can extend for thousands of feet (meters), causing pressure effects damage.
An air blast can also disturb combustible dusts (such as coal or HSC ores), which could ignite and cause a
secondary explosion. Air is eventually discharged from the mine.
Air Blasting: method of blasting in which compressed air at very high pressure is piped to a steel shell in a
shot hole and discharged.
Air Shaft: shaft used for ventilating mines, downcast when delivering fresh air into the mine and upcast when
exhausting air from the mine to the surface.
ANFO: mixture of explosive grade ammonium nitrate (AN) and diesel fuel oil (FO) commonly used in mining
excavation blasting due to its low cost, inherent stability, and ease of handling.
Back (Roof): interior exposed rock ceiling of an underground tunnel, slope, drift, or adit.
Bulkhead: timber or concrete dam which holds air, tailings, or water in place
Burst: sudden and violent release of energy and pressure contained in a stressed rock (see air burst and
rock burst)
Cage: personnel or equipment elevator located in a shaft.
Cap: uppermost heavy crosspiece timber in a timber set, supported on timber columns or posts. (See Timber
Sets)
Cave-in: partial or complete collapse of a mine working
Chute: opening underground through which ore can gravity flow from an active upper mining level to a lower
haulageway level, usually used to load ore into mobile equipment or conveyors for transport from the mine.
Chutes can be constructed of natural rock or be wood lined.
Collar: surface at the top of and surrounding the throat of a vertical shaft.
Colliery: underground coal mine
Crib: system of timbering in which the timbers are laid one upon the other to form a rectangular opening in
the center, often used to line ore chutes and ore passes
Cross-cut: horizontal level driven at an angle to the strike of a vein
Drift: see adit
Entry: coal mining term for adit
7-12
17-17
Page 73
Fig. 42. Ventilation system using shafts for a deep metal mine.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 74
Fig. 43. Drawing of a typical underground mine operation showing chutes, grizzlies, cribs, and typical ground support
methods. (Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
Grizzly: a rugged fixed or mobile screen or series of closely spaced parallel steel rods or rollers use to rough
size or scalp ore of a comparatively large size. Often used prior to primary crushers to separate boulders
from smaller rock. Grizzlies are often located underground below chutes ahead of ore bins. A mantle is a type
of grizzly.
Grout: a filling agent injected by pressure into loose and broken rock or ground to stabilize the area
Gunite: an air-blown mortar consisting of one part cement and three to five parts sand, used for coating
surfaces to prevent rock fall.
Hard Rock Mining: applies to mining involving very hard mineral deposits such as metal ores or non-metal
structural materials such as granite or marble, as differentiated from softer materials such as coal, trona or potash. Hard rock mining often involves frequent blasting of deposits to loosen ore and requires significantly
more downstream crushing and grinding to obtain desired particle size. Coal and soft non-metallics are
removed faster and easier by continuous grinding, scraping, water pressure, or augering devices.
Haulageway: horizontal underground passageway used primarily to move ore or waste by self propelled or
rail mounted mobile equipment.
Head Frame (a/k/a Hoist Frame or Gallows Frame): structure positioned over a vertical or near vertical shaft
for transporting materials, personnel, waste, and ore to and from an underground mine. Head frames (and
associated hoisting equipment) are usually located aboveground but can also be located underground. Older
head frames may be constructed of wood timbers. Newer head frames are usually of steel frame construction with metal cladding or are built into hard rock structures underground. Pulleys (sheave wheels) and wire
ropes are usually provided at the top of the head frame. Drive machinery and motors are usually located in
nearby hoist rooms. (See hoist).
Hoist: a machine, usually driven by one or more large, often synchronous, electric motors, which is used to
raise and lower one or more conveyances in a mine shaft using wire ropes. Mine hoists are categorized
as either drum or friction types. Drum hoists have one end of the wire rope or ropes anchored to the drum.
The wire ropes are wound and unwound from the drum to move the conveyances. Friction (aka Koepe) hoists
raise and lower the conveyance by passing the hoisting or head ropes over a wheel and driving the ropes by
means of friction. Hoisting equipment is located in buildings or rooms near hoist frames.
Inby (Inbyside): in the direction of the face of the mine or further into the mine. Opposite of outby.
7-12
17-17
Page 75
Fig. 44. Head frame structure at modern non-metal mine. Hoist house is to the left.
(Courtesy of Elf Aquitaine, TGI Soda, Grainger WYO)
In-Situ (in place) (Solution Mining): method of mining minerals that can be recovered by liquid dissolution
at the mineral source inside the mine. Also called selective chemical extraction. An example of in-situ mining
is that involving sulfur or salt deposits. Hot water is pumped into the deposit to dissolve the desired material.
The pregnant solution is pumped to the surface as a slurry where it is further processed.
Lagging: planks or timbers placed around or behind timber sets to keep rock material from falling from the
walls or the back of the tunnel. Wood lagging can significantly contribute to combustible loading and fire
spread. (See Timber Sets)
Lateral: a secondary or tertiary horizontal passageway, usually parallel to a haulageway. It is used for utilities
such as power cables, piping, or for ventilation air.
Level: horizontal underground working (usually a series of interconnected tunnels and passageways) that
is connected to a shaft. A level forms the basis for excavation of the ore above or below. A deep mine will have
several working levels.
Mantle: See Grizzly
Mining: extracting, recovering, and exploiting minerals or coal from their natural environment and transporting
them to the point of processing or final use.
Outby (Outbyside): direction away from the face of the mine or toward the outside of the mine. Opposite of
inby.
Portal: surface entrance into a horizontal mine tunnel or adit.
Pillar: unmined portion of an ore deposit which provides temporary support during mining of adjacent areas
or rooms. An ore pillar is eventually mined for valuable minerals during a retreating process during which
the mine back is allowed to collapse and fill the mined out area. Pillar is also used to describe the two vertical
supports of a timber set or other material such as concrete, used to support a mine back.
7-12
17-17
Page 76
Fig. 45. Close up view of head frame in Figure 44, showing wire ropes from adjacent hoist room, sheave wheel at
top, and structural supports. (Courtesy of Elf Aquitaine, TGI Soda, Grainger WYO)
7-12
17-17
Page 77
7-12
17-17
Page 78
Prop/Stull: single timber post used to support loose rocks or a low outcropping of the mine back. Props (coal
mine term) and stulls (metal mine term) are commonly used in stopes. Props can give early visual warning
of tunnel back failure by bending and cracking.
Raise: excavation of restricted cross section driven upward, either vertically or at a steep angle, from one
level in a mine to another.
Rock Burst: violent release of energy contained in highly stressed rock when the rock formation suddenly collapses, expelling material and pressure out into an adit or tunnel. Rock bursts can cause high pressure waves
(piston forces) through tunnels for hundreds or thousands of feet. Rock bursts can occur in coal and metal
mines. Coal bursts can be caused by methane gas pockets within coal deposits. Metal rock bursts are caused
by unstable geological structures and faults within the mine and can be initiated by earthquakes or poor mine
back support.
Rockbolt: steel bolt with an expansion wedge at one end inserted into a drill hole. One of several methods
to support mine backs where rock is unstable.
Roof: overhead of the mine tunnel (commonly called the back)
Shaft: vertical or near vertical opening into the earth used to extract waste and ore from the mine, for personnel
and equipment entry, for utility cables and pipes, and as a conduit for mine ventilation. Shafts can be many
thousands of feet (meters) deep and be lined with wood or noncombustible materials.
Shaft Station (Station): enlargement of a shaft (or a room) made for staging of equipment delivered to and
from the shaft and for personnel entry into drifts at that elevation. Several stations are normal along the vertical
length of a typical shaft.
Shotcrete: generic term used for hydraulically pressure spraying a cementitious material such as gunite on
walls and other surfaces.
Skip: self dumping bucket in which ore or waste rock is raised through a vertical shaft to the surface.
Slope: inclined or declined opening into the mine, usually passing through undesirable waste materials to
reach a valuable ore deposit.
Fig. 48. Isometric layout of an underground mine showing levels and mining terms.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 79
7-12
17-17
Page 80
Fig. 49. Plan and cross section views of typical shafts and levels of an underground mine.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 81
Fig. 50. Drawing of underground metal mine supported by ore pillars. Shown is a room and pillar mining method of an
inclined ore body. (Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
Fig. 51. Drawing of a hardrock mine featuring concrete pillars which temporarily support a longwall mining zone.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 82
Stinkdamp: term for hydrogen sulfide gas formed as a by-product of burning coal. Hydrogen sulfide is an
explosive gas.
Stope: short branch from a slope or decline tunnel where ore is mined. Stopes commonly follow ore seams
and are often on an incline to facilitate gravity flow of mined ore. Stopes are commonly layered one above
the other in a step-like formation.
Stopping: barrier installed in an underground tunnel, drift, adit, or entry to control smoke, fire, gas, water,
or ventilation. A fire door is a form of mine stopping as is a bulkhead.
Sump: lowest part of the mine where water is collected and removed by pumping, commonly at the bottom
of a vertical hoist shaft.
Surface mining: extraction of minerals or coal aboveground from the surface of the earth. Surface mining
is conducted where ore or coal reserves are close to the surface by one of the following methods:
Open Pit (Open Cut): open extraction for removing ore near the surface or where a high concentration
of minerals in a deep body are more economical to access from the surface. Bench, strip and quarry mines
are types of open pit. Large man-made open pits generally have circular benches sloping inward into
the pit for truck and heavy equipment access. The larger open pits can be miles (kilometers) across and
thousands of feet (meters) deep. Moveable primary crushers and conveying systems may be present
inside the pit. Generally, large open pits are not refilled once mining operations cease. Instead, gangue
(waste) is separated from the desired ore in concentrator mills and placed on large tailings piles or stacks.
Strip: open cut surface mining of coal. Usually an overburden of a 100 ft (30 m) or less is removed by
draglines to expose a relatively thin layer of coal which is then extracted with large front end loaders into
trucks or conveyor systems. Strip mines can extend for miles across open country. Overburden is replaced
after the coal is removed and the terrain is usually restored.
Quarry: surface mining of structural rock such as sandstone, granite, slate, and marble. Mining is done
by high pressure water or special saws that cut the desired material into blocks. Aggregate (sand and
7-12
17-17
Page 83
Fig. 53. Cross section view of a typical wood lined vertical shaft.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
gravel) extraction is also usually classified as quarry mining. This is a suitable technique for bench layered
deposits.
Placer: mining technique using panning, sluicing, hydraulic, or dredging of valuable metals such as gold
and tin or gemstones from an alluvial sand or gravel deposit. It is used where a ready supply of water
is available and where high grade ore, pure metal or gemstones are present on or near the surface.
Hydraulic methods, using high pressure water, are used to remove gravel overburden. Floating dredges
or moveable processing plants remove ore from under shallow water (such as in river or lakes) and in
some cases contain on board concentration equipment. Placer mining is environmentally disturbing and
reclaim of disturbed overburden is usually required.
Glory Hole: vertical hole accessed from the surface but with a narrow throat at the bottom which feeds
mined ore downward into an underground storage area where it is transported to the surface by other
means.
Tipple: structure used to load ore or coal into trucks or rail cars for haulage to a remote conveying or tram system or directly to a concentrator mill. Also used for dumping ore into crusher facilities. A device is used to
tip mine ore cars onto their sides. The ore falls by gravity down a chute into the crusher chute or waiting haulage vehicle, staged at a lower level. The tipping device may feature a hydraulic fluid system. Older tipples
are almost always of wood frame construction; newer ones usually feature steel or concrete construction.
Older tipples may connect to a wood frame trestle that supports a rail line for ore cars arriving from the mine.
This may create a significant continuity of combustible loading, especially if the mine has wood timber sets
near the portal.
Timber Set: Mine back support structure that is comprised of two wood timber uprights (pillars) and one wood
timber cross beam (cap). Timber sets are spaced several feet (meters) apart and may or may not have wood
lagging next to the mine back or walls as additional support or protection against falling materials. Structural
steel and reinforced concrete sets are also used. Wood timbers have historically been preferred by miners as
7-12
17-17
Page 84
they give advanced warning and long term trending of mine collapse by noise, cracking, and bending.
7-12
17-17
Page 85
Fig. 56. Schematic view of large open pit copper mine and mills.
(Bingham Canyon Mine, Courtesy of Rio Tinto Mining, Kennecott Copper, Utah)
Tunnel: a generic term for a horizontal (or nearly horizontal) opening into the earth for ore extraction, personnel
and equipment entry, or ventilation purposes. Strictly speaking, a tunnel has openings at both ends. Adits,
drifts, entries and slopes are all forms of tunnels, but they usually have only one entrance.
Underground Mining: removal of minerals from beneath the surface of the earth. Underground mining is
usually conducted where ore reserves are not close to the surface or do not lend themselves to open pit type
operations. There are many underground mining methods including the following:
Self Supported: mining method in geologically firm ground which needs no additional ground support.
Room-and-pillar: mining method where large columns (pillars) of valuable ore are purposely left in place
to support the mine back, leaving large open rooms around the supports. After a room has been mined,
the pillars are mined and the mine collapses inwardly, filling the room.
Stoping: act of excavating ore in a series of steps.
Sublevel Stoping: stoping method in which the ore is excavated in open stopes, retreating from one end
to the other. The ore is dropped into chutes to lower level haulage ways.
Shrinkage Stoping: stoping method in which the ore is removed from vertical overheads and allowed to
fall onto the floor of the stope. The buildup of ore on the floor helps support the walls.
Cut-and-fill stoping: stoping method in which the ore is excavated by successive flat or incline slices in
an upward direction from the level. It is similar to shrinkage stoping. However, after each slice is blasted
down, all broken ore is removed. The stope is filled with waste almost up to the roof (back) of the stope
before the next slice is blasted out. This leaves room on the top of the waste on which to stand and work.
Open Stope: stoping in which no regular artificial method of ground support is used except occasionally
individual stulls (props) or cribs which hold localized patches of insecure ground. The walls and back of
7-12
17-17
Page 86
Fig. 57. Photograph of surface strip mining of coal. Dragline is used for overburden removal.
7-12
17-17
Page 87
Fig. 60a. Section view of a single timber set used underground for ground support.
an open stope are self supporting. Open stopes are used where the ground is firm and stable.
Longwall: mechanized mining system used for layered deposits of coal and soft non-metallics such as
salt, potash and trona. Longwall mining features wide cuts along a long face up to 3000 ft (914 m) long
and intentional caving and hydraulic support systems. One large piece of mobile excavating equipment with
moving conveyor systems is used along a single mining face. The longwall excavator has hydraulic lifters that hold the back of the mine in place until the coal along the seam is cut and removed. As the machine
moves laterally along the seam, the back of the mine is allowed to collapse and fill the mined area as
it is released from hydraulic support.
Shortwall: similar to longwall but features multiple excavators along the longwall to avoid complete loss
of production if a single unit is out of service. It is not a commonly used process.
7-12
17-17
Page 88
Fig. 60c. Section view of a timber set with wood plank lagging
Fig. 60d. Isometric view of a series of timber sets with wood plank lagging
Sublevel caving: stoping method in which relatively thin layers of ore collapse (cave) by successively
undermining small panels. Chute raises connect a lower level haulage road to the caved area. The ore
falls down the chutes and is hauled away.
Block caving: mass mining system where the ore extraction depends on gravity. By removing a thin
horizontal layer at the mining level of the ore column, the vertical support of the ore column above is
removed and the ore caves by gravity. As broken ore is removed, the ore above continues to break and
cave. Block caving is no longer widely used.
Panel caving: systematic and safe block caving technique which features smaller areas of caving.
Walls: sides of a tunnel, drift, adit, or entry.
7-12
17-17
Page 89
Whitedamp: carbon monoxide (CO) formed by spontaneous combustion or slow oxidation of coal or other carbon based materials. Carbon monoxide is an explosive gas common to coal mines. It also can be formed
by combustion in wood timber sets or in discarded waste organic materials in metal mines.
Winze: shaft-like opening sunk from a level in a mine to develop, dewater, or ventilate an ore zone. Similar
to a raise but usually used for auxiliary utility, rather than ore extraction.
A.3 Ore Processing and Refining Terms
A-Frame: storage building for crushed or concentrated ore or coal. Usually has an overhead rubber belt gallery
to feed piles and an underpile reclaim tunnel featuring hydraulic systems and rubber belts.
Acid plant: chemical processing facility for converting sulfur oxides (created as undesirable by-product gases
in smelters and oxidation/reduction processes) to a marketable sulfuric acid and clean air that can be
discharged to the environment. Acid plants and their associated air and chemical handling systems are used
primarily as an emission control system but also usually produce acid for plant processes. Excess acid is
sold. An acid plant features upstream mist and dust precipitators, absorbers, converters, drying towers, heat
exchangers, and strippers. Acid plants often have large fibre reinforced plastic (FRP) duct systems or other
combustible construction (older facilities may have wood duct systems) that feed a high stack or chimney
which may be plastic lined. Usually a plant cannot operate if the acid plant is shutdown, although factors such
as production reliance on by-product acid, regulatory laws, prevailing winds, and emission stack height all
play a role in permission to operate a metal refinery without acid recovery.
7-12
17-17
Page 90
Fig. 63. Sublevel stoping with large hole drilling and blasting.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
Fig. 64. Sublevel stoping with ring drilling as the primary means of breaking ore.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 91
7-12
17-17
Page 92
Activator (Activity Reagent): liquid chemical, used in flotation processes, which is added to a pulp (ore slurry)
to increase the floatability of the mineral or to refloat a depressed (sunk) mineral. Also see reagent.
Aeration: introduction of air into pulp in a flotation cell in order to form air bubbles on which mineral values
can be collected.
Agglomeration: beneficiation (flotation) process based on the adhesion of pulp particles to water. Loosely
bonded associations of particles and bubbles are formed that are heavier than water; flowing film gravity separation is used to separate the agglomerated material from the nonagglomerated materials. Agglomeration
7-12
17-17
Page 93
is also used to prepare certain types of very fine oxide ores for heap leaching. In the process, fine ore is
heated in a kiln in the presence of weak sulfuric acid to form soft agglomerized pebbles. These are cooled
and layered onto the heap leach pad where they allow cyanide liquid to more easily penterate the pile
because of the voids created around the soft pebbles. Agglomeration is also a metallurgical refining process
for forming balls, briquettes, nodules, flakes, or other size shaped particles from loose, usually fine incoherent
particles.
Autogenous mill: rotating cylinder using ore impact to reduce particle size. Artificial media such as steel balls,
pebbles, or rods are not used in fully autogenous mills. A form of ore comminution. (See semi-autogenous
[SAG] mills)
Ball Mill: A rotating grinding cylinder using steel balls as the grinding media. A form of ore comminution.
Beneficiation: non-metallurgical refining (concentration or dressing) of metal ore or coal to separate waste
material from valuable minerals. The most common beneficiation process is froth flotation whereby fine ore
or coal is captured on bubbles or froth created by agitated reagents in special cells, tanks or troughs.
Bio-Leaching: process for recovering metals from low-grade ores by dissolving them in solution, aided by
bacterial action.
Carbon-In-Pulp (CIP) Process: method of recovering gold and silver from pregnant cyanide solutions (such
as from a heap leaching operation) by adsorbing the desired metals onto activated carbon. The metal is
subsequently removed from the carbon by weak cyanide solution cleansing and electrowinning.
7-12
17-17
Page 94
Fig. 70. Block caving in a massive orebody, showing a conventional mining layout.
(Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
Fig. 71. Photo of A-Frame building for bulk coal storage, with incline, totally enclosed
conveyor belt delivery and reclaim system.
7-12
17-17
Page 95
7-12
17-17
Page 96
Fig. 72. Photo of gas cooling, scrubbing, and precipitation equipment associated with a typical emission control acid plant.
Most of equipment and ducting in this photo are of fiber reinforced plastic construction.
Column Flotation: milling process in a tall cylindrical column in which valuable minerals are separated by
their wetability properties.
Comminution: ore or rock particle size reduction by breaking, crushing, and grinding.
Concentration: separating waste material (gangue) from valuable mineral to produce marketable metals. Beneficiation and various extractive metallurgical processes, such as smelting, are all forms of concentration.
Many mines use several types of concentration processes in series to produce increasingly higher grades of
concentrate or metal, until the final desired metal content is achieved.
Concentrating Mill (a/k/a Mill or Concentrator): metal/non-metal mineral processing plant used to grind
and separate ore into small particles to obtain desired mineral value for further downstream refining and to
separate undesired waste tailings. Mills may contain multiple side-by-side grind circuits. Each grind circuit
usually features one or more autogenous, semi-autogenous (SAG), and/or ball and rod mills with associated
hydrocyclones, pumps, piping, and dewatering systems. Following grinding the desired mineral is separated
from the gangue by flotation, thickeners, gravity, shaker table, magnetic, or other physical separation
process. Mill circuits feature extensive rubber lined equipment, plastic screens, rubber conveyor belts,
grouped electrical cables with plastic insulation, large hydraulic and lubrication fluid systems, and combustible or flammable liquid reagents. In cold climates, grind circuits are housed inside buildings. Newer mill buildings are of noncombustible construction, although foamed-in-place plastic insulation may be present inside
metal panel sandwich walls or used as protection in areas where corrosive materials are present. Plastic
(FRP) light panels in roofs and walls are common. Older mills are of all wood or of metal clad wood frame
construction. Concentrating facilities in warm climates are usually located outdoors.
Constriction Deck: fluidizing section of a fluidized coal dryer (in a coal preparation plant). It consists of metal
grating or parallel steel bars through which hot air is blown to dry the wet coal.
Crushing: one of several steps in comminution to obtain desired ore particle size. Crushing is achieved by
compressing the ore between two rigid surfaces or by impacting the particle against a massive surface.
Crushed rock is usually sized in inches (cm) or larger. Large mines use several levels of crushing (primary,
secondary, and even tertiary) to break the ore smaller and smaller before it is pulverized in a grinding mill.
7-12
17-17
Page 97
7-12
17-17
Page 98
Typical crushers are jaw, gyratory, Symons (a specialized form of gyratory), cone, stamp mill, and impact
(hammermill). Primary crushers may be underground, inside pits, or located at a concentrator plant.
Cyanidation: chemical extraction process which uses a weak sodium or calcium cyanide solution to dissolve
metals from low-grade ore. Used principally for highly oxidized ores and commonly used for gold, silver and
copper recovery. (Also see leaching, lixivation, and heap leaching.) Cyanidation can be carried out in leach
tanks (vats), in heap leach piles, or in-situ underground or in open pits. The metal-rich cyanide solution
(pregnant liquor) is processed to remove the desired metals, often by a carbon-in-pulp (CIP) or solvent
extraction recovery process. The separated aqueous stream (raffinate) is recovered and reused.
Dewatering: removal of water from ore concentrate or coal slurries or pulps. Concentrated ore or coal slurries
are often transported to remote metal refining plants by pumping through a slurry pipeline. Once received,
water is removed by centrifuging or by filter presses, hydrocyclones, rotacones, or hydroclassifiers. Filter
presses may be vacuum or pressure type and may feature hydraulic fluid systems.
Electrometallurgy: recovery of metal using electric current. Electrothermal and electrolytic are two types of
electrometallugy. Electrothermal processes use electric current as a heat source and usually fall under pyrometallurgical processing (which is not further covered in this document). Electrolytic processes use electric
current to transport metal ions from anodes and/or electrolytes for deposition on cathodes. Electrolytic
processes may feature acidic solutions or salt bath. Commonly used for final high purity refining after other
metallurgical processing has been completed. Electrowinning and electro-refining are common forms of
electrolytic processing.
Electro-refining: electrometallurigical process in which the desired metal in solution is deposited (by the application of a DC current) onto a cathode that is constructed of the same material as the metal being refined.
Starter sheets are used as the cathodes and the deposited metal builds up on these sheets. The undesired
impurities (slimes) accumulate at the base of the anode in the electrolytic cell or tank. Slimes contain sufficient
precious metal values to be further processed. Electro-refining is commonly used for cobalt, nickel, zinc,
7-12
17-17
Page 99
Fig. 76. Coal preparation plant using a hillside for gravity flow of product. In the photo, coal is delivered at the top into
raw coal silos, into the beneficiation and cleaning building, and then into the dryer building, center. From the dryer
it is conveyed into the clean coal silos for rail shipment.
and copper. Older cell tanks were constructed of wood. Newer tanks are usually concrete or an expoy resin
mixed with concrete. Glass fiber reinforced plastic might be used.
Electrostatic Separation: concentration using variances in electrical conductivity to recover desired materials.
Zirconium is commonly recovered by electrostatic methods.
Electrowinning: electrometallurigical process of winning a metal from a solution using DC electric current
in cells. Similar to electro-refining, the desired metal as well as the impurities are usually deposited on the
anode (a sheet or a sponge) instead of the cathode. The anode is then immersed in an acid solution where
a DC current is applied and deposited metals are dissolved into solution. Once in solution, the metal lowest
in electro-motive series (EMS) is preferentially plated onto a cathode, leaving the other metals in solution.
The solution is recycled or processed to recover other metals; alternatively, the solution is sent off site, via
effluent treatment, as waste. The desired metal is recovered from the cathode by mechanical, thermal or
chemical methods. Electrowinning is commonly used for gold and silver refining. Electrowinning cells may
be constructed of polypropylene plastic or rubber (or plastic) lined carbon steel. Non-lined stainless steel is
being used in newer plants to reduce combustibility.
Extractive Metallurgical Processing: chemically altering ore and concentrates to produce marketable-quality
metals and metallic compounds. Included are pyrometallurgical, electrometallurgical, and hydrometallurgical
processes. These types of concentration processes may be located at one large mine site in series or at
separate sites to which several mines produce feedstock concentrates.
Froth Flotation: physiochemical process using reagents and water to selectively separate (by attachment to
bubbles) desired materials from undesired materials. Flotation tanks or cells are usually constructed of steel
but may be rubber lined or of plastic construction. Flotation processes are located downstream of grinding
circuits.
7-12
17-17
Page 100
Fig. 77. Concentrator complex at diamond mine. (Photo courtesy of Rio Tinto)
Gravity Separation: separating (concentrating) solids based on different specific gravities in a fluid medium.
Sluice boxes, spiral centrifuges, shaking tables, and sink-float suspensions are examples.
Grinding: a step of comminution (size reduction) to obtain a fine particle or powder after primary or secondary
crushing is completed. Grinding involves a variety of methods. Ball, rod, autogenous, and semiautogenous (SAG) mills are most common. Grinding, which is done both wet and dry, produces ore of a talc-like consistency. The ground ore is usually transported as a water slurry or pulp.
Heap leaching: extractive metallurgical process for recovering metals from mostly weathered, low grade or
spent oxidized ores. Heap leaching is not suitable for sulfide ores. A slightly sloping pad is constructed using
an impervious liner such as plastic or compacted clay (see leach pad) and the crushed, agglomerized, or runof-mine (ROM) ore is placed on the liner in high and long piles by mobile equipment or moveable conveyors.
Piles may be as high as 200 ft (60 m) and thousands of feet (meters) long. They may be constructed across
valleys. They feature pyramid type shapes with step benches to prevent failure. A leach solution (commonly weak sodium cyanide), is sprayed over the ore pile using traditional irrigation type sprinklers, and
allowed to percolate down through the ore. Over time (weeks to months) the leach solution dissolves the
desired metal into a pregnant solution which flows by gravity and is captured in lined ponds below the pad.
The pregnant solution is pumped or transported by tanker truck to a processing plant where the metal is
extracted by chemical processes, such as Carbon-In-Pulp (CIP), or solvent extraction. The aqueous stream
(raffinate) recovered in the CIP or extraction process is returned to the process or sent off site as waste effluent. Heap leaching is commonly used for gold, copper, and silver and is very common in the Western United
States, South America, and Australia. Structural failure of a heap pile or liner leakage under a pile can cause
contamination of pregnant liquor and environmental damage. Extensive downtime can occur while the heap
leach pile is repaired or the liner exposed and patched.
Hydrocyclone: cyclone that separates fine mineral dust from a water slurry, usually downstream of wet grinding
mills, in a grind circuit. Usually multiple small hydrocyclones are mounted together in a bank over a single discharge tank recovering the output from one grind circuit. The discharge tank, hydrocyclones, and piping from
the mills are rubber lined. Some hydrocyclones are being lined with noncombustible ceramics.
7-12
17-17
Page 101
Fig. 78. Gold mine concentrating facility. Due to tropical location much of process area is located outdoors. This facility
has a single ball mill with two SAG mills, one on either side. Tanks at rear of photo are part of a vat leaching
operation.
Hydrometallurgy: selective dissolution of metals from ores and concentrates using solvents or solutions.
Examples are in-situ, heap or vat leaching and solvent, liquid-liquid, or liquid-ion exchange extraction.
Ammonia, kerosene, sodium cyanide, mineral acids (i.e., sulfuric acid), and water are used in hydrometallurigical processes. Processes may be at elevated temperatures and pressures. Two examples of
hydrometallurgical processes are shown in Figures 99 and 100.
Jig: milling equipment used to concentrate ore on a screen submerged in water, usually by a reciprocating
motion of the screen, or by the action of the flowing water. Jigs can be constructed of high density plastics and
can ignite from hot work when dry.
Launder: chute or trough for conveying pulp, water, or powdered ore in a mill. Launders can be rubber lined.
Leachate (Lixivium): mineral-in-solution product of leaching. Also called pregnant liquor.
Leaching (lixivation): separation, selective removal, or dissolving-out of soluble constituents from an ore by
the natural action of percolation water or reagent solutions. Commonly used to recover fine grain gold, silver
and zinc from low-grade ores using sodium or calcium cyanide or sulfuric acid solutions. (See cyanidation,
heap, and vat leaching)
Leach Pad (Leach Dump): impervious layer, usually of compacted clay over which rests a plastic liner, on
which a low grade ore pile is placed for solvent leaching. (See heap leaching)
Liquid-Ion Exchange: hydrometallurgical method using liquid solvents such as kerosene, ammonia, acids,
and cyanides in an electrolytic bath to dissolve, depose and recover metals. A form of solvent extraction.
Liquid-Liquid Extraction: see solvent extraction.
Liner: hard metallic alloy, ceramic, or polymeric based material used to line the interior of mills, pipes,
cyclones, pumps, pump impellers, spiral separators, troughs, flotation cells, and slurry tanks. Liners provide
abrasion resistance to interior steel surfaces. Rubber linings are prevalent, creating significant fire potentials
7-12
17-17
Page 102
7-12
17-17
Page 103
Fig. 81. Photo of a mobile crusher at open pit mining operation. (Courtesy of Alcoa)
in otherwise noncombustible occupancies. A liner is also a mining term denoting a brick, concrete, wood,
or other casing in a mine tunnel or shaft.
Magnetic Separation: concentration using magnetic fields to differentially separate ferrous materials from nonferrous materials. Iron ore compounds are commonly recovered by this method. Examples of electromagnetic
separators are drum magnet and wet high intensity magnetic separators (WHIMS).
Pebble Mill: rotating grinding cylinder using ceramic or physically formed natural rock pebbles as the grinding
media. A form of ore comminution.
Polishing Pond: final pond in a series of tailings or settling ponds through which mill waste effluents pass
before they are discharged into the natural environment.
Polymeric Materials: hydrocarbon based substances that are used in construction or found in mining and
ore processing occupancies. Examples are coal deposits, wood timber sets, plastic insulation on electric
cables, synthetic rubbers used in equipment liners, conveyor belts, etc.
Pyrometallurgy: concentrating processes using refractory-lined furnaces and high temperatures created by
electrical energy, by burning fossil fuels, or by burning ore at extremely high temperatures. Refined metals are
produced. Drying, roasting, sintering, distilling, smelting, and fire refining are all examples of pyrometallurgical
processes.
Pulp: mixture of water and ground or pulverized ore or coal capable of flowing or being pumped as a liquid
or slurry.
Reagent: liquid used in beneficiation flotation or solvent exchange process to cause bubble formation or
for selective absorption or adsorption of the desired mineral or coal. Flotation reagents fall into four general
categories: collector agents (i.e., xanthates, fatty acids and petroleum sulfonates); pH modifiers (i.e., lime,
7-12
17-17
Page 104
Fig. 82. Drawing of a gyratory crusher inside a multistory reinforced concrete crushing facility. In this facility, rail mounted
cars from an underground mine are brought to the top of the building and the ore load is delivered into the crusher
throat by a tipple. Note the spare crusher cone stored next to the tipple. Crushed ore is sent via conveyor belt
to an ore pile or surge bin from which it is further crushed or processed. (Figure courtesy of Society of Mining,
Metallurgy, and Exploration, Inc. (SME), Littleton, Colorado)
7-12
17-17
Page 105
Fig. 83. Drawing of in-situ solution mining (cyanide leaching) in an open pit. At top is a drawing of a typical heap leach
pad using cyanide leaching. (Figure courtesy of Society of Mining, Metallurgy, and Exploration, Inc. (SME),
Littleton, Colorado)
Fig. 84. Photo of a copper electro-refining cell (tank) house. Walkways between cells are wood plank. Cells are
concrete lined with a thin polymer plastic. (Courtesy of Cominco Quebrada, Chile)
7-12
17-17
Page 106
Fig. 85. Photo of plastic screen (blue) inside flotation tank. Also refer to photo of flotation circuit under Beneficiation, above.
soda ash, sodium hydroxide, and sulfuric acid); activator agents (i.e., copper sulfate, calcium chloride and
lead acetate); and frother agents (i.e., methyl isobutyl carbinol [MIBC], pine oil, kerosene, various
depressants, and sodium cyanide). MIBC is a common frother used in both mineral and coal beneficiation
and is a low flash point flammable liquid. See Table 2 for a list of common flotation reagents and their fire
hazard characteristics.
Rod Mill: rotating grinding cylinder using long steel rods as the grinding media. A form of ore comminution.
Semi-autogenous (SAG) mill: rotating grinding cylinder using a combination of steel balls and ore-to-ore contact as the grinding media. A form of ore comminution. World-class size SAG mills are 36 ft (11 m) in diameter and 18 ft (5.4 m) long, driven by 16,000 HP (11936 KW) synchronous motors. (See Grinding for photo
of a SAG mill)
Screen: flat or cylindrical device surfaced with openings to selectively size rocks or ore. Screens can shake
or rotate and be constructed of metal or high density plastic. Commonly found downstream of crushers or
mills in a grind circuit.
Sheave Wheel: large grooved wheel at the top of a headframe over which the wire hoisting rope passes.
(See Fig 5 for photo of sheave wheel on head frame)
Size Reduction (Comminution): breaking, crushing, and grinding wet or dry ore to achieve desired size for
concentration. Grizzlies, cone and jaw crushers, autogenous and semi autogenous (SAG) mills, ball and rod
mills, tumblers, and screening machinery are all examples of size reduction equipment.
Solvent (Liquid-Liquid) Extraction (SX): separation of one or more substances from a mineral mixture by treating a solution of the mixture in a solvent. The solvent is usually comprised of a carrier, an extractant, and
a phase modifier that will dissolve the desired mineral, leaving the undesirable materials for disposal or other
processing. Kerosene is commonly used as the carrier, which normally accounts for 8085% of the total solvent volume. Common extractants, which account for 1020% of the solvent, are tri-butyl phosphate and
quartenary amines. A typical phase modifier is isodecanol, which may account for 5% of the total volume of
7-12
17-17
Page 107
Fig. 86. Photo of world-class size semi-autogenous (SAG) mill in copper concentrator facility. (Courtesy of Rio Tinto)
the solvent. Tanks in newer SX processes are commonly FRP or other plastic. Older processes may feature
wood tanks. SX is commonly used for copper, nickel and uranium ores. (See Fig 100 for a typical SX process
flow diagram.)
Tailings (Tails): gangue and other refuse material resulting from the washing, concentrating, and treatment
of ground ore, which is generally too poor in mineral value to be treated further.
Tailings Pond(Stack/Pile/Dam): liquid or semi-liquid waste gangue and by-product trace reagent and other
chemicals derived from processing and concentration of ore. The waste product is delivered by pipeline to the
pond in a water slurry. The pond is usually held in place by a sloped earthen dam. Most of the water is drained
or decanted and returned to the process. Remaining water is allowed to evaporate over time, stabilizing the
stack and leaving the undesired heavy metals or toxins (such as trace cyanides) to settle and be retained. Tailings ponds can be hundreds of feet (meters) high with steep walls and thousands or feet (meters) long and
wide, if not miles (kilometers). Dam wall stability is of concern to prevent failure and downstream flooding. Liquefaction (and resultant failure) of a poorly designed earthen dam can be caused by earthquakes,
sonic vibrations, floods, heavy surface water runoff, or other unusual natural occurrences. Modern tailings
ponds have durable plastic liners and their dams are specially engineered structures featuring layers of rock
and compacted earth, designed by experts to resist worst case prevailing natural events. The most common root cause failures of tailings piles are improper filling, day-to-day operation, and maintenance.
Thickener (Thickener-Settler): open tank with a sub-surface rake for solid-liquid separation of desired mineral.
The liquid is usually an aqueous solution and overflows the top into troughs. New troughs and thickner tanks
are concrete or steel and can be rubber lined. Older plants may use wood tanks and troughs.
Trommel: large, rotating size separation screen at the outlet of a grinding mill, such as a SAG mill. The screen
is normally covered by a metal shroud. Trommel screens are often constructed of high density polyurethane
plastic. They are usually ignited by hot work operations when the enclosing shroud is open for maintenance.
7-12
17-17
Page 108
Fig. 87. Photo of large DC drive motor for this SAG mill. (Courtesy of Rio Tinto)
7-12
17-17
Page 109
Fig. 88. Photo of parallel ball mills in a copper concentrator facility. Often two small ball mills are paired with
one large SAG mill for final grinding. (Courtesy of Rio Tinto)
Fig. 89. Cutaway view drawing of a rod mill, showing internal components. Note the layered rods which are steel bars
which vary in diameter and length, depending on the size of the mill. The rods rotate with the mill, fine grinding the ore.
7-12
17-17
Page 110
Fig. 90.
Process flow diagram of a grind circuit featuring multiple stages of crushing with ball and rod mill grinding.
Fig. 91.
Process flow diagram of a grind circuit featuring a single crusher with SAG and ball mill grinding.
7-12
17-17
Page 111
Fig. 92. Photo of a cross valley gold heap leaching operation, built into a sloping mountain. Note the bench pyramid shape
and exposed rubber liner (black area at upper right). Pregnant solution pond is at lower center. Note size of ore
haulage truck at center in relationship to size of heap leach pile. (Photo courtesy of Newmont Mining Company,
Yanacocha Mine, Peru)
Fig. 93. Drawing of heap leach operation showing pile and pregnant solution collection pond.
7-12
17-17
Page 112
Fig. 94. Closeup drawing of heap leach pile showing cyanide solution distribution system.
Fig. 95. Photo of rubber lined raffinate pond at copper heap leaching and solvent extraction mine.
(Courtesy of Cominco Quebrada, Chile)
7-12
17-17
Page 113
Fig. 96. Photo of hydrocyclone bank (six hydrocyclones) positioned over a collection tank.
These hydrocyclones and the discharge tank are all rubber lined.
7-12
17-17
Page 114
Fig. 99. Process flow of a typical heap leaching, carbon-in-pulp, and electrowinning circuit for
hydrometallurgical recovery of gold and silver.
7-12
17-17
Page 115
7-12
17-17
Page 116
Fig. 102. Photo of rubber liner inside a large diameter steel pipe flange.
7-12
17-17
Page 117
7-12
17-17
Page 118
Fig. 105. Photo of SX plant at copper mine. (Photo courtesy of Cominco Quebrada, Chile)
7-12
17-17
Page 119
Fig. 107. Thickener tanks at copper concentrator plant. (Courtesy of Rio Tinto)
7-12
17-17
Page 120
Fig. 108. Photo of exposed plastic trommel screen at outlfow of large SAG mill.