Professional Documents
Culture Documents
PFR Lab Report
PFR Lab Report
ABSTRACT
The purpose of conducting this experiment were to carry out the saponification reaction
between Sodium hydroxide ( NaOH ) and Ethyl Acetate (Et(Ac)), to determine the effect of
residence time to the reactions extent of conversion and to evaluate the reaction rate constant
of this saponification reaction. SOLTEQ Plug Flow Reactor (Model: BP101) unit was used
to run this experiment or usually called as PFR, and also some common laboratory apparatus
for titration process. The NaOH and Et(Ac) solution were mix and reacted in the PFR and
the output product was analysed by using titration method. The results shows that the
conversion of NaOH solution did shows a large difference at each residence time, because the
conversion should nearly constant at each residence time. This can happen due to some
errors that occurred.
2.0
INTRODUCTION
Type of chemical reactors remains a highly discussed subject in chemical process industries
worldwide.The reactor is of course, the place where chemical reactions take place. Hence it is
arguably the single most important part of any chemical process design. The design of a
reactor must be finely tuned so that its mechanisms suit the necesseties of the process that is
to be carried. Depends on the nature of the materials in both the feed and of course the
products, the reactors may take a wide range of forms. This is why full comprehension of a
reactor of a particular design as well as its working mechanisms is very much vital to actually
conduct a particular chemical process.
In this experiment, the Plug Flow Reactor (Model: BP101) is used as it has been properly
designed for students' experiment on chemical reactions in liquid phase under isothermal and
adiabatic conditions. Included in the unit is a jacketed plug flow reactor; individual reactant
feed tanks and pumps, temperature sensors and conductivity measuring sensor. By using this
particular unit, students will be capable to conduct the typical saponification reaction between
ethyl acetate and sodium hydroxide among the others reaction.
3.0
OBJECTIVES
The objectives of this experiment were to carry out the saponification reaction between
Sodium Hydroxide ( NaOH) And Ethyl Acetate (Et(Ac)), to determine the effect of residence
time to the extent of reaction of conversion and to evaluate the reaction rate constant of this
saponification reaction.
4.0
THEORY
where A and B represent reactants while C and D represent products. In this reaction, A and B
is being diminished and C and D is being produced. Rate of reaction, concerns itself with
how fast the reactants diminish or how fast the product is formed. Rate of reaction of each
species corresponds respectively to their stoichiometric coefficient. As such :
r A r B r C r D
=
= =
a
b
c d
The negative sign indicates reactants.
A usual equation for rA is :
r A=k C A C B
where
k
rate constant
CA
concentration of A species
CB
concentration of B species
stoichiometric coefficient of A
stoichiometric coefficient of B
4.2 Conversion
Taking species A as the basis, the reaction expression can be divided through the
stoichiometric coefficient of species A, hence the reaction expression can be arranged as
follows :
b
c
d
A + B+ C + D
a
a
a
Conversion is an improved way of quantifying exactly how far has the reaction moved, or
how many moles of products are formed for every mole of A has consumed. Conversion XA is
the number of moles of A that have reacted per mole of A fed to the system. As seen below :
X A=
moles of A reacted
moles of A fed
In a plug flow reactor, the feed enters at one end of a cylindrical tube and the product stream
leaves at the other end. The long tube and the lack of provision for stirring prevent complete
mixing of the fluid in the tube. Hence the properties of the flowing stream will vary from one
point to another.
In an ideal tubular flow reactor, which is called plug flow reactor, specific assumptions are
made regarding the extent of mixing:
1. no mixing in the axial direction
2. complete mixing in the radial direction
3. a uniform velocity profile across the radius.
Tubular reactors are one type of flow reactors. It has continuous inflow and outflow of
materials. In the tubular reactor, the feed enters at one end of a cylindrical tube and the
product stream leaves at the other end. The long tube and the lack stirring prevent complete
mixing of the fluid in the tube.
5.0
LAB APPARATUS :
burette
conical flask
measuring cylinder
ph indicator
beakers
CHEMICAL USED :
6.0
De-ionised water
METHODOLOGY / PROCEDURE
6.2Experiment Procedures
1. The general starts up procedures were performed.
2. Valves V9 and V11 were opened.
3. Both the NaOH and Et(Ac) solutions were allowed to enter the plug reactor R1 and empty
into the waste tank B3.
4. P1 and P2 were adjusted to give a constant flow rate of about 300 ml/min at flow meters
FI-01 and FI-02. Both flow rates were ensured same. The flow rates were recorded.
5. The inlet (QI-01) and outlet (QI-02) were started to monitor the conductivity values until
they do not change over time. This is to ensure that the reactor has reached steady state.
6. Both inlet and outlet steady state conductivity values were recorded. The concentration of
NaOH exiting the reactor and extent of conversion from the calibration curve.
7. Optional. Sampling was opened from valve V15 and 50ml of sample was collected. A back
titration procedure was carried out manually to determine the concentration of NaOH in the
reactor and extent of conversion.
8. The experiment was repeated from step 4 to 7 for different residence times by reducing the
feed flow rates of NaOH and Et(Ac) to about 250,200,150,100 and 50 ml/min. Both flow
rates were made sure to be equal.
6.3Back Titration Procedures
1. The burette was filled up with 0.1 M NaOH solution.
2. 10 mL of 0.25 M HCl was poured in a flask.
3. 50 mL samples that were collected from the experiment at every controlled flow rate (300,
250, 200, 150, 100 and 50 mL/min) were added into the 10mL HCl to quench the
saponification reaction.
4. 3 drops of phenolphthalein were dropped into the mixture of sample and HCl.
5. The mixture then was titrated with NaOH until it turns light pink.
6. The amount of NaOH titrated was recorded.
Residence Time,
Reactor volume ( L ) ,V
L
Total flow rate
, v0
min
( )
4L
0.6 L/ min
= 6.6667 min
placed in Table 2
Other residence times were calculated by the same way, and varying the flow rates.
7.2 Conversion
For flow rates of 300 ml/min :
Moles of reacted NaOH, n1
n1
= Concentration NaOH x Volume of NaOH titrated
= 0.1 M x 0.0161 L
= 0.00161 mole
Moles of unreacted HCl, n2
Moles of unreacted HCl
n2 = n1
n2 = 0.00161 mole
Volume of unreacted HCl, V1
V1
n2
concentration HCl quenc h
0.00161
0.25
= 0.00644 L
Volume of HCl reacted, V2
V2
= Concentration HCl x V2
= 0.25 x 0.00356
= 0.00089 mole
= n3
= 0.00089 mole
n4
volume sample
0.00089
0.05
= 0.0178 M
Xunreacted
Xunreacted =
0.0178
0.1
= 0.178
Xreacted
Xreacted
= 1 - Xunreacted
= 1 - 0.178
= 0.822
placed in Table 2
Hence, at flow rate 300mL/min of NaOH in the reactor, about 50.6% of NaOH is reacted with
Et(Ac). Other conversions were calculated by the same way, and varying the flow rates.
7.3 Reaction Rate Constant,k
k=
v0
X
V TFR C AO 1X
VTFR
CAO
= 0.822 ( X- reacted)
k=
0.6
0.822
10.822
(4)(0.1)
= 6.9269L.mol/min
placed in
Table 2
Other Reaction Rate Constants were calculated by the same way, and varying the flow rates.
7.4 Rate of Reaction, -rA
placed in Table 2
Other Rate of Reactions were calculated by the same way, and varying the flow rates.
8.0
RESULT
Reactor volume
:4L
: 0.1 M
: 0.1 M
No.
Flow rate
Flow rate
Total
Residence
Outlet
Inlet
of NaOH
of Et(Ac)
flowrate
time, t
conductivit
conductivit
(mL/min)
(mL/min)
of
(ms/cm)
y (ms/cm)
y (ms/cm)
5
5
5
5
5
5
6.7
6.7
6.8
5.5
5.0
4.0
8.4
8.7
9.0
7.6
7.1
6.7
solutions.
V0
1
2
3
4
5
6
300
250
200
150
100
50
300
250
200
150
100
50
(mL/min)
600
500
400
300
200
100
Table 1
Residence Time,
Conversion, X,
Reaction Rate
, (min)
6.6667
8.0000
10.0000
13.3333
20.0000
40.0000
(%)
82.2
85.0
87.4
89.8
85.8
92.2
Constant,k (L.mol/min)
6.92690
7.08330
6.93665
6.60294
3.021126
2.955130
(mol.L/min)
0.00219472
0.00159375
0.00110126
0.00068696
0.00060918
0.00017979
Table 2
conversion, %
94
92
90
88
86
84
82
80
78
76
Residence Time,
Figure 1
9.0
DISCUSSION
Plug Flow Reactor (PFR) consists of cylindrical pipe that operate at steady state. In this type
of reactor, the feed enters at one end of cylindrical tube and the product will leaves at the
other end. The properties of the flowing stream will vary from one point to another.
In this experiment, the type of solution that used were NaOH and Et(Ac). These two
solutions will react in the PFR to undergo saponification reaction. In order to achieve the
objective of this experiment, the residence time have to be manipulated throughout the
experiment, and thus the effect of each one is studied. It can be seen that residence time is a
function of total flow rates of the feed. The flow rates of the feed solution have been varied
by 300, 250, 200, 150, 100 and 50 mL/min respectively.
In table 1, the raw data that consisting inlet flow rates, conductivity value and residence time
was tabulated. From this graph, the effect of residence time can be studied. Conversion is a
property that shows the percentage of the reaction has taken place. From figure 2, it can be
seen that the conversion values shows fairly increasing in value and it have to be almost
constant. Since the PFR is designed not to stir the solution vigorously to maximise mixing
process, the conversion by using PFR is also fairly slow.
10.0
CONCLUSION
The objective of this experiment which were to carry out the saponification process between
NaOH and Et(Ac) and the relationship was graphed in figure (1) was conducted in this
experiment. The results that were obtained was not really satisfied the theory of PFR as the
increasing of residence time, suppose the value of conversion of reaction should be almost
constant. From this experiment, the value rate of reaction this particular reaction were also
being done by doing some calculation as shown in sample calculation section.
11.0
RECOMMENDATIONS
1)
The titration should be stop as soon as the Et(Ac) solution turned pink pale colour.
2)
The flow rates of the feed should be constantly monitored so that it remain constant
throughout the reaction.
3)
4)
12.0
REFERENCES
1)
2)
3)
4)