IM32Q02B10 31E (Messages)
IM32Q02B10 31E (Messages)
Manual
Messages
IM 32Q02B10-31E
IM 32Q02B10-31E
4th Edition
Introduction
This manual describes the details of Diagnostic Information messages displayed in the Diagnostic Information Window of SCS Maintenance Support Tool or System Alarm View of HIS.
The table of the contents of this manual can be used as message number index.
This manual consists of the following chapters:
Chapter 1 : This chapter explains how to refer to the Diagnosis Information in SENG.
Chapter 2 : This chapter explains the details about SCS Messages.
Chapter 3 : This chapter explains the details about common messages of CENTUM VP or
CS 3000 and SENG.
Appendix : A list of the alarm class for the corresponding message number is provided.
IM 32Q02B10-31E
ii
To protect the system controlled by the Product and the Product itself and to ensure safe
operation, please observe the safety precautions described in this Manual. Yokogawa
Electric Corporation ("YOKOGAWA") assumes no liability for safety if users fail to observe
the safety precautions and instructions when operating the Product.
If the Product is used in a manner not specified in the User's Manuals, the protection provided by the Product may be impaired.
If any protection or safety circuit is required for the system controlled by the Product or for
the Product itself, please install it externally.
Use only spare parts that are approved by YOKOGAWA when replacing parts or consumables of the Product.
Do not use the Product and its accessories such as power cords on devices that are not
approved by YOKOGAWA. Do not use the Product and its accessories for any purpose
other than those intended by YOKOGAWA.
The following symbols are used in the Product and User's Manuals to indicate the accompanying safety precautions:
Indicates that caution is required for operation. This symbol is labeled on the Product to refer the user to the User's Manuals for necessary actions or behaviors in
order to protect the operator and the equipment against dangers such as electric
shock. In the User's Manuals, you will find the precautions necessary to prevent
physical injury or death, which may be caused by accidents, such as electric
shock resulting from operational mistakes.
Identifies a protective conductor terminal. Before using the Product, you must
ground the protective conductor terminal to avoid electric shock.
Identifies a functional grounding terminal. A terminal marked "FG" also has the
same function. This terminal is used for grounding other than protective grounding.
Before using the Product, you must ground this terminal.
Indicates an AC supply.
Indicates a DC supply.
Indicates the ON position of a power on/off switch.
Indicates the OFF position of a power on/off switch.
Hand over the User's Manuals to your end users so that they can keep the User's Manuals on hand for convenient reference.
Thoroughly read and understand the information in the User's Manuals before using the
Product.
For the avoidance of doubt, the purpose of the User's Manuals is not to warrant that the
Product is suitable for any particular purpose but to describe the functional details of the
Product.
IM 32Q02B10-31E
iii
Every effort has been made to ensure the accuracy of contents in the User's Manuals.
However, should you have any questions or find any errors, contact us or your local distributor. The User's Manuals with unordered or missing pages will be replaced.
Except as specified in the warranty terms, YOKOGAWA shall not provide any warranty for
the Product.
YOKOGAWA shall not be liable for any indirect or consequential loss incurred by either
using or not being able to use the Product.
n Notes on Software
YOKOGAWA makes no warranties, either expressed or implied, with respect to the Software Product's merchantability or suitability for any particular purpose, except as specified in the warranty terms.
Purchase the appropriate number of licenses of the Software Product according to the
number of computers to be used.
No copy of the Software Product may be made for any purpose other than backup; otherwise, it is deemed as an infringement of YOKOGAWA's Intellectual Property rights.
No reverse engineering, reverse compiling, reverse assembling, or converting the Software Product to human-readable format may be performed for the Software Product.
No part of the Software Product may be transferred, converted, or sublet for use by any
third-party, without prior written consent from YOKOGAWA.
IM 32Q02B10-31E
iv
Documentation Conventions
n Symbols
The following symbols are used in the User's Manuals.
Identifies instructions that must be observed to avoid physical
injury, electric shock, or death.
Identifies instructions that must be observed to prevent damage
to the software or hardware, or system failures of the Product.
Identifies important information required to understand operations or functions.
Identifies additional information.
n Typographical Conventions
The following typographical conventions are used throughout the User's Manuals.
Mark
Indicates that a space must be entered between character strings.
Example:
.ALPIC010-SC
IM 32Q02B10-31E
v
(RS Project Folder)\SCS0101
If the RS Project Folder is C:\MYRSPJT, the above path becomes C:
\MYRSPJTSCS0101.
n Drawing Conventions
Drawings used in the User's Manuals may be partially emphasized, simplified, or omitted for
the convenience of description.
Drawings of windows may be slightly different from the actual screenshots with different settings or fonts. The difference does not hamper the understanding of basic functionalities and
operation and monitoring tasks.
SEE
ALSO
For more information about the functions and usage of CENTUM VP components for integrating the Product
with CENTUM VP, refer to:
User's Manuals (IM), Technical Information (TI), and General Specifications (GS) of CENTUM VP
For more information about the features and usage of CENTUM CS 3000 components for integrating the
Product with CENTUM CS 3000, refer to:
User's Manuals (IM), Technical Information (TI), and General Specifications (GS) of CENTUM CS 3000
n Station Types
A safety control station (hereafter referred to as SCS) is named according to the type of the
safety control unit used in it.
Table Info-1 Names of SCS and Safety Control Unit Used
Name of SCS
SCSV1-S
SSC10S/SSC10D
SCSP1-S
SSC50S/SSC50D
SCSP2-S
SSC60S/SSC60D
SCSU1-S
SSC57S/SSC57D
IM 32Q02B10-31E
vi
In the User's Manuals, the following abbreviations may be used to describe functions of these
SCS as a whole.
IM 32Q02B10-31E
vii
n Trademark Acknowledgments
Microsoft, Windows, Windows Vista, Windows Server, Visual Basic, Visual C++, and Visual Studio are either registered trademarks or trademarks of Microsoft Corporation in the
United States and other countries.
Adobe, Acrobat, and Adobe Reader are registered trademarks of Adobe Systems Incorporated.
All other company and product names mentioned in the User's Manuals are trademarks
or registered trademarks of their respective companies.
TM or mark are not used to indicate trademarks or registered trademarks in the User's
Manuals.
Logos and logo marks are not used in the User's Manuals.
IM 32Q02B10-31E
Toc-1
Messages
IM 32Q02B10-31E 4th Edition
CONTENTS
1.
2.
1.2
1.3
Toc-2
No. 4128 Setting PASSWD FB to OFF ......................................................... 2-9
No. 4129 GPS interface unit error ...............................................................2-10
No. 4130 Recovery of GPS interface unit ................................................... 2-10
No. 4131 Communication module lock ....................................................... 2-10
No. 4132 Cancellation of Communication module lock .............................. 2-10
No. 4133 Information of a diagnosis error in the received data of SCS Link
Transmission. .............................................................................. 2-11
No. 4134 Information of a diagnosis error recovery in the received data of
SCS Link Transmission. .............................................................. 2-12
No. 4135 SCS Link Transmission data lock ................................................2-12
No. 4136 Cancellation of SCS Link Transmission data lock ....................... 2-13
No. 4137 Number of Locked Stations in SCS Link Transmission Exceeded .....
..................................................................................................... 2-13
No. 4138 Recovery from exceeded number of locked stations in SCS Link
Transmission ............................................................................... 2-13
No. 4139 Inter-SCS Safety Communication data lock ................................ 2-13
No. 4140 Cancellation of Inter-SCS Safety Communication data lock ....... 2-14
No. 4141 Number of locked stations in Inter-SCS Safety Communication
exceeded .....................................................................................2-14
No. 4142 Recovery from exceeded number of locked stations in Inter-SCS
Safety Communication ................................................................ 2-14
No. 4143 Start of automatic scan period extension .................................... 2-14
No. 4144 Cancellation of automatic scan period extension ........................ 2-15
No. 4145 Abnormal calculation occurred .................................................... 2-15
No. 4146 Recovery from abnormal calculation ........................................... 2-15
No. 4151 Information of retainable data initialization .................................. 2-16
No. 4152 Online change of scan period ......................................................2-16
No. 4153 Information of Inter-SCS Safety Communication data lock time-up ...
..................................................................................................... 2-16
No. 4154 Information of forced cancellation of Inter-SCS Safety
Communication data locks .......................................................... 2-16
No. 4155 Information of SCS Link Transmission status change. ................2-17
No. 4156 Information of SCS Link Transmission definition change ............ 2-17
No. 4157 Information of SCS Link Transmission wiring change ................. 2-17
No. 4158 Information of SCS Link Transmission lock time-up ....................2-17
No. 4159 Information of forced cancellation of SCS Link Transmission locks ...
..................................................................................................... 2-17
No. 4160 Invalid password for Manual Operation FB ................................. 2-18
No. 4161 Information of Output IOM Shutdown ..........................................2-18
No. 4162 Information of communication I/O definition change ................... 2-18
No. 4163 Information of communication I/O wiring change ........................ 2-18
No. 4164 Information of disabling security level change .............................2-18
No. 4165 Information of enabling security level change ............................. 2-19
No. 4166 Information of communication module lock time-up .................... 2-19
IM 32Q02B10-31E
Toc-3
No. 4167 Information of forced cancellation of communication module locks ...
..................................................................................................... 2-19
No. 4168 Information of tag name change by online change download ............
..................................................................................................... 2-19
No. 4169 NVRAM diagnosis error ...............................................................2-19
No. 4170 Flash memory diagnosis error .....................................................2-20
No. 4172 Information of resource change by online change download ...... 2-20
No. 4173 Completion of writing to flash memory ........................................ 2-20
No. 4174 Failed to write to flash memory ................................................... 2-21
No. 4175 Failed to update external communication data ............................2-21
No. 4177 Information of SCS security level change ................................... 2-21
No. 4178 Information of security level time-up ............................................2-22
No. 4179 Information of communication I/O module output enabled operation .
..................................................................................................... 2-22
No. 4180 Information of password change ................................................. 2-22
No. 4181 Information of output enabled operation ......................................2-22
No. 4182 Information of output module start operation ...............................2-23
No. 4183 Request to upload SOE to SENG ............................................... 2-23
No. 4184 Notification on saving SOE trip signal file in SCS ....................... 2-23
No. 4185 Information of variable value change .......................................... 2-23
No. 4186 Information of lock time-up .......................................................... 2-24
No. 4187 Information of forced cancellation of locks .................................. 2-24
No. 4188 Start of online change download ................................................. 2-24
No. 4189 Completion of online change download ...................................... 2-24
No. 4190 Online change download error .................................................... 2-24
No. 4191 Completion of I/O definition rewriting .......................................... 2-25
No. 4192 Information of override state time-up ...........................................2-25
No. 4193 Information of forced release of all overrides .............................. 2-25
No. 4194 Information of override enabled state time-up .............................2-25
No. 4195 Information of communication I/O data status change ................ 2-26
No. 4196 Invalid password for PASSWD FB ...............................................2-26
No. 4197 Information on active PASSWD FB time-up ................................ 2-26
No. 4198 Information on forced reset of PASSWD FB ................................2-26
No. 4199 Override communication error .....................................................2-27
3.
IM 32Q02B10-31E
Toc-4
No. 0015 Self-diagnosis error of clock inside CPU module .......................... 3-4
No. 0017 ROM checksum error of CPU module ...........................................3-4
No. 0021 Internal task error of safety control station .................................... 3-5
No. 0023 Mapping block fatal error ...............................................................3-5
No. 0025 Function control word error ........................................................... 3-5
No. 0027 Mapping block record information error .........................................3-5
No. 0033 Online downloading abnormal end ................................................3-5
No. 0041 Safety control station fan alarm .....................................................3-6
No. 0042 Recovery from safety control station fan alarm ............................. 3-6
No. 0043 Safety control station temperature alarm ...................................... 3-6
No. 0044 Recovery from safety control station temperature alarm ...............3-7
No. 0045 Power supply module alarm of safety control station .................... 3-7
No. 0046 Recovery from power supply module alarm of safety control station .
....................................................................................................... 3-7
No. 0047 Battery alarm of CPU module ........................................................3-7
No. 0048 Recovery from battery alarm of CPU module ................................3-8
No. 0055 Information of same frame reception in online change download
communication .............................................................................. 3-8
No. 0057 Information of online change download error ................................ 3-8
No. 0059 Information of recovery from node power failure ...........................3-8
No. 0063 ESB bus error ................................................................................3-8
No. 0064 Normal recovery of ESB bus ......................................................... 3-9
No. 0065 Failure of ESB Bus Interface module (SSB401) of node ...............3-9
No. 0066 Normal recovery of ESB Bus Interface module (SSB401) of node ....
..................................................................................................... 3-10
No. 0067 Failure of power supply module of node ..................................... 3-10
No. 0068 Normal recovery of power supply module of a node ................... 3-10
No. 0069 Error before database download to I/O module .......................... 3-10
No. 0081 Failure of I/O module ................................................................... 3-11
No. 0082 Normal recovery of I/O module ................................................... 3-13
No. 0083 I/O module database error occurred ........................................... 3-13
No. 0085 I/O module communication error occurred .................................. 3-13
No. 0086 Recovery from I/O module communication error .........................3-13
No. 0087 Node error occurred .................................................................... 3-13
No. 0088 Normal recovery of node ............................................................. 3-14
No. 0089 Subsystem communication error .................................................3-14
No. 0090 Subsystem communication recovered ........................................ 3-15
No. 0093 CPU nodes housekeeping unit error ...........................................3-15
No. 0094 Normal recovery of CPU nodes housekeeping unit ....................3-15
3.2
IM 32Q02B10-31E
Toc-5
No. 0451 Information of switching of control side of safety control station ........
..................................................................................................... 3-16
No. 0452 Information of switching of standby side of safety control station .......
..................................................................................................... 3-16
No. 0459 Information on I/O module service side .......................................3-16
No. 0460 Information of I/O module out service ......................................... 3-16
No. 0471 Normal completion of online change download ...........................3-17
No. 0474 Information of tag list duplicate error ........................................... 3-17
No. 0475 Start of database download to I/O module .................................. 3-17
No. 0476 Normal completion of database download to I/O module ............3-17
No. 0477 Database download error to I/O module ..................................... 3-17
No. 0480 Heavy load on periodical processing ...........................................3-18
3.3
IM 32Q02B10-31E
TocApp.-1
Messages
IM 32Q02B10-31E 4th Edition
CONTENTS
Appendix
Appendix 1. Alarm Class..................................................................... App.1-1
IM 32Q02B10-31E
1.
1-1
IM 32Q02B10-31E
1-2
1.1
MYRSPJT
Station
Domain:01
V net 1
V net 2
SCS Status
CPU Status
Ready
R-Fail
Ready
CPU status
Comment
Station Comment
Figure 1.1-1 SCS Status Overview Window and Diagnostic Information button
2.
IM 32Q02B10-31E
1-3
1.2
Help button
Toolbar
Alarm class
Diagnostic Information
Message
Number
Date
Class
Message
4125
5/30/2008 10:26:19.720 AM
4125
5/30/2008 10:26:19.720 AM
0082
5/30/2008 10:26:17.620 AM
0476
5/30/2008 10:26:09.131 AM
0475
5/30/2008 10:26:04.235 AM
0082
5/30/2008 10:25:55.320 AM
0459
5/30/2008 10:25:55.320 AM
0476
5/30/2008 10:25:51.931 AM
0475
5/30/2008 10:25:48.388 AM
0047
5/30/2008 10:25:36.851 AM
4129
5/30/2008 10:25:33.328 AM
0081
5/30/2008 10:25:33.320 AM
Number
Date
Class
Message
30/95
Alarm marks
Warning
Status bar
Number of currently
generated messages
SEE
ALSO
For more information about the diagnostic information window, refer to:
3.2, Displaying SCS Diagnostic Information in Utilities and Maintenance Reference (IM
32Q04B20-31E)
SEE
ALSO
1.
2.
For more information about the Help dialog box, refer to:
3.2.3, Diagnostic Information Message Help Function in Utilities and Maintenance Reference (IM
32Q04B20-31E)
IM 32Q02B10-31E
1-4
1.3
SCS0101 1.3
Format
Selection mark
page 1/1
IM 32Q02B10-31E
2-1
2.
No.xxxx
Message name
Printing example
Meaning
Meaning of a message.
Example: The security level is set to 1 for the duration exceeding the time
limit (8 hours in the above example) specified in SYS_SECURE Function
Block (hereinafter referred to as FB).
Cause
Describes the cause of occurrence. The description may be omitted depending on the message.
Example: The security level has not been reverted.
Action
Remark
Note
Error code
Describes details of the error code included in the message, if any. The description may be omitted depending on the message.
IM 32Q02B10-31E
2-2
2.1
No.4101
Message name
Printing example
Meaning
Cause
The following causes may be considered. Check the error codes for more detail.
Stop/restart on the producing side SCS
Problem in the communication path
Change in the application of inter-SCS safety communication
Remark
Error code
The first four digits are an error code, and the next four digits are a cause
code. The error detail can be found from the descriptions of the both codes.
The error codes and cause codes are listed below.
The error code represents the type of error. The following table explains each
error code and the action you can take to fix the error.
Description
Action
5040
5041
5042
5043
The cause code represents the event that caused the problem and is logical
OR of the following codes.
Table 2.1-2 Message No. 4101 - Cause Code List
Code (hexadecimal)
Errors
Description
Presumed cause
8000
No response
4000
Reset detection
IM 32Q02B10-31E
2-3
Errors
Description
Presumed cause
2000
1000
CRC mismatch
0400
0200
0100
Address error
0040
0020
0010
0004
Different FB ID information
Internal error
0001
Internal error
Temporary communication
error
Temporary communication
error
Communication was interrupted or the producer SCS is
stopped.
An application was created
incorrectly.
No.4102
Message name
Printing example
Meaning
Cause
Remark
No.4103
Message name
Printing example
Variable lock
In the case of I/O variables:
SCS0101 Variable Locked Variable=VAR001 NODE 01 SLOT 02 CH 03
In the case of internal variables:
IM 32Q02B10-31E
2-4
Remark
Note
The variable (VAR001 in the above example) was locked by operation from
the SENG. In the case of I/O variables, the channel position (node 1, slot 2
and channel 3 in the above example) corresponding to the variable is also included in the message.
Forcing function
Be sure to unlock the variables that were locked.
If an IO_BOOL type or IO_REAL type variable is locked, the member variable
v or status will be indicated in the format of [Variable=VAR001.v] at the position of the variable name in the system alarms. If the variable is not wired to
the channel, the member variable v will be always displayed. Nevertheless, in
any of the above cases, the whole IO_BOOL type or IO_REAL type variable
will be locked.
When locking an array element, the whole array will be locked. Under this circumstance, the variable name displayed in the system alarm will be attached
with the array element subscript as [Variable=VAR001[1]].
No.4104
Message name
Printing example
Meaning
Remark
Note
The lock of the variable (VAR001 in the above example) was cancelled by operation from the SENG. In the case of I/O variables, the channel position
(node 1, slot 2 and channel 3 in the above example) corresponding to the variable is also included in the message.
Forcing function
If an IO_BOOL type or IO_REAL type variable is unlocked, the member variable v or status will be indicated in the format of [Variable=VAR001.v] at the position of the variable name in the system alarms. If the variable is not wired to
the channel, the member variable v will be always displayed. Nevertheless, in
any of the above cases, the whole IO_BOOL type or IO_REAL type variable
will be unlocked.
Moreover, when unlocking an array element, the whole array will be unlocked.
Under this circumstance, the variable name displayed in the system alarm will
be attached with the array element subscript as [Variable=VAR001[1]].
No.4105
Message name
Printing example
Meaning
Remark
Note
IM 32Q02B10-31E
2-5
No.4106
Message name
Printing example
Meaning
Remark
No.4107
Message name
Printing example
Meaning
Remark
Note
No.4108
Message name
Printing example
Meaning
Remark
No.4109
Message name
Printing example
Meaning
Remark
Note
No.4110
Message name
Printing example
Meaning
Remark
No.4111
Message name
Printing example
Meaning
2-6
Remark
Note
Forcing function
Be sure to cancel the locks of the I/O modules that were locked.
No.4112
Message name
Printing example
Meaning
Remark
No.4113
Message name
Printing example
Meaning
Cause
This is an operation from the SENG. The number of locks is too many.
Action
Remark
Note
SYS_FORCE FB
Lock variables within the limit count.
No.4114
Message name
Printing example
Meaning
Cause
Remark
No.4115
Message name
Printing example
Meaning
Remark
Override setting
SCS0101 TAG001 Overridden (Instance = OVR0001)
Override operation was performed for the override FB (OVR0001 in the above
example) that corresponds to the tag name (TAG001 in the above example)
from the HIS.
OVR_B, OVR_I, OVR_R, OVR_IB, OVR_IR, GOV_B, GOV_IB FB
No.4116
Message name
Printing example
Cancellation of override
SCS0101 TAG001 Override Released (Instance = OVR0001)
IM 32Q02B10-31E
2-7
Meaning
Remark
An override was cancelled for the override FB (OVR0001 in the above example) that corresponds to the tag name (TAG001 in the above example) from
the HIS.
OVR_B, OVR_I, OVR_R, OVR_IB, OVR_IR, GOV_B, GOV_IB FB
No.4117
Message name
Printing example
Meaning
Cause
Remark
Note
No.4118
Message name
Printing example
Meaning
Cause
Remark
Note
No.4119
Message name
Printing example
Meaning
Cause
This is an operation from the HIS. There are too many overrides.
Action
Cancel overrides.
Remark
Note
SYS_OVR FB
Override within the limit count.
No.4120
Message name
Printing example
Meaning
Cause
2-8
Remark
SYS_OVR FB
No.4121
Message name
Printing example
Meaning
Action
Remark
Note
No.4122
Message name
Printing example
Meaning
Remark
No.4123
Message name
Printing example
Meaning
Cause
This is an operation from the HIS. There are too many active PASSWD FBs.
Action
Inactivate (reset to OFF) the PASSWD FBs that have exceeded the limit
count.
Remark
Note
SYS_PSWD FB
Make PASSWD FBs active within the limit count.
No.4124
Message name
Printing example
Meaning
Cause
Remark
IM 32Q02B10-31E
2-9
No.4125
Message name
Printing example
Meaning
Cause
Code
Description
TRNS+
5121
TRNS-
5122
IOP+
5123
IOP-
5124
Ovr Range
5125
5126
Ch Fail
5127
Action
Remark
Check to see if the connected devices and connecting cables are normal.
No.4126
Message name
Printing example
Meaning
No.4127
Message name
Printing example
Meaning
Setting PASSWD FB to ON
SCS0101 TAG001 PASSWD FB Set to ON (Instance = PASSWD001)
PASSWD FB (PASSWD001 in the above example) that corresponds to the tag
name (TAG001 in the above example) was set to ON (active) by operation
from the HIS.
No.4128
Message name
Printing example
Meaning
IM 32Q02B10-31E
2-10
No.4129
Message name
Printing example
Meaning
Cause
Action
Note
Problem in the cable connecting the GPS unit and the GPS interface unit.
Check to see if a cable connecting the GPS unit and the GPS interface unit is
disconnected or cut. Also, check to see if a terminator is connected to the
ends of the cable. If everything is in place, replace the GPS interface unit.
If this message is displayed while the time synchronization method is V net
time synchronization, the CPU module may be faulty.
No.4130
Message name
Printing example
Meaning
No.4131
Message name
Printing example 1
Printing example 2
Printing example 3
Meaning
Remark
Note
The communication module was locked by operation from the SENG. The
message varies depending on the locked range (inputs and outputs, inputs only or outputs only). The location of the communication module is also included
in the messages (such as node 1, slot 2).
Forcing function, subsystem communication
Be sure to cancel the lock of the communication module that was locked.
No.4132
Message name
Printing example 1
Printing example 2
Printing example 3
Meaning
The lock of the communication module was cancelled by operation from the
SENG. The message varies depending on the locked range (inputs and out-
IM 32Q02B10-31E
2-11
puts, inputs only or outputs only). The location of the communication module is
also included in the messages (such as node 1, slot 2).
Remark
No.4133
Message name
Printing example
Meaning
A diagnosis error has been found in the received data of SCS Link Transmission. The source station number (such as 05) and the station type (SCS in the
above example) that sent the Link Transmission are indicated in the message
text. The station type indicated in the message is the station type defined on
the SCS Link Transmission builder.
Cause
The following causes may be considered. Check the error codes for more detail.
Stop or restart the sender station
Problem in the communication path
The definition of the SCS Link Transmission builder may contain errors.
Remark
Error code
The first four digits are an error code, and the next four digits are a cause
code. The error detail can be found from the descriptions of the both codes.
The error codes and cause codes are listed below.
The error code represents the type of error. The following table explains each
error code and the action you can take to fix the error.
Description
Action
5041
5042
5043
The cause code represents the event that caused the problem and is logical
OR of the following codes.
Table 2.1-5 Message No. 4133 - Cause Code List
Code (hexadecimal)
Errors
Description
Presumed Cause
8000
No response
2000
Temporary communication
error
Continues on the next page
IM 32Q02B10-31E
2-12
Errors
Description
Presumed Cause
1000
Temporary communication
error, or SCS Link Transmission builder definition may
contain [Type] error.
0400
0100
Address error
0040
0020
0010
0008
Internal error
No.4134
Message name
Printing example
Meaning
Cause
Remark
No.4135
Message name
Printing example
Meaning
IM 32Q02B10-31E
2-13
Remark
Note
No.4136
Message name
Printing example
Meaning
Remark
No.4137
Message name
Printing example
SCS0101 Number of Locks about SCS Link Transmission Exceeds the Limit =
3
Meaning
The number of locked stations exceeded the limit (3 in the above example),
which is defined in SYS_FORCE_ LT FB as the number of stations allowed for
forcing.
Cause
Action
Remark
Note
No.4138
Message name
Printing example
SCS0101 Number of Locks about SCS Link Transmission Within the Limit = 3
Meaning
The number of locked stations fell within the limit (3 in the above example),
which is defined in SYS_FORCE_ LT FB as the number of stations allowed for
forcing. (This is the recovery message of No.4137.)
Cause
Remark
No.4139
Message name
Printing example
Meaning
IM 32Q02B10-31E
Remark
Note
2-14
No.4140
Message name
Printing example
Meaning
Remark
No.4141
Message name
Printing example
Meaning
Cause
Action
Remark
Note
No.4142
Message name
Printing example
Meaning
Cause
Remark
The number of locked stations fell within the limit (3 in the above example),
which is defined in SYS_FORCE_ BD FB as the number of stations allowed
for forcing. (This is the recovery message of No.4141.)
Operation from the SENG
SYS_FORCE_BD FB
No.4143
Message name
Printing example
IM 32Q02B10-31E
2-15
Meaning
Cause
Remark
Automatic extension of the scan period of the application logic execution started. (In the above example, the original scan period of 100 ms was extended
to 200 ms.)
The application caused heavy load on the SCS.
SYS_SCANEXT FB, automatic scan period extension
No.4144
Message name
Printing example
Meaning
Cause
Remark
No.4145
Message name
Printing example 1
Printing example 2
Meaning
Cast Overflow :
Overflow in casting
At Program=, the name of the program (POU name) where the abnormal calculation occurred is indicated. If the abnormal calculation occurred in a userdefined FU/FB, the POU name of that FU/FB is indicated at FU/FB=.
Cause
Remark
No.4146
Message name
Printing example 1
Printing example 2
Meaning
2-16
Cast Overflow :
Overflow in casting
At Program=, the name of the program (POU name) where the abnormal calculation occurred is indicated. If the abnormal calculation occurred in a userdefined FU/FB, the POU name of that FU/FB is indicated at FU/FB=.
Cause
Remark
No.4151
Message name
Printing example
Meaning
Cause
Action
Set the setting values of the external communication function blocks with data
retaining function again.
Remark
Data retaining function, external communication function blocks with data retaining function (ECWR_B, ECWR_I, ECWR_R), ACCUM FB, AGA_R FB
No.4152
Message name
Printing example
Meaning
Cause
Remark
No.4153
Message name
Printing example
Meaning
Inter-SCS Safety Communication lock exceeded the time limit (8 hours in the
above example) specified in SYS_FORCE_BD FB.
Action
Check whether all Inter-SCS Safety Communication locks have been cancelled and cancel unnecessary locks.
Remark
No.4154
Message name
Printing example
2-17
Meaning
Cause
Remark
Locks of all the Inter-SCS Safety Communication data (reception/transmission) in the station were forcibly cancelled.
Locks of all the Inter-SCS Safety Communication data were cancelled by using the SYS_FORCE_BD FB.
Forcing function, Inter-SCS Safety Communication, SYS_FORCE_BD FB
No.4155
Message name
Printing example
Meaning
Remark
No.4156
Message name
Printing example
Meaning
Cause
No.4157
Message name
Printing example
Meaning
Cause
No.4158
Message name
Printing example
Meaning
Action
Remark
No.4159
Message name
Printing example
2-18
Meaning
Locks of all the locked SCS Link Transmission were forcibly cancelled.
Cause
Remark
No.4160
Message name
Printing example
Meaning
Cause
The password entered from the HIS and the password set in Manual Operation FB did not match.
Action
Remark
No.4161
Message name
Printing example 1
Printing example 2
Meaning
Remark
No.4162
Message name
Printing example
Meaning
Cause
No.4163
Message name
Printing example
Meaning
Cause
No.4164
Message name
2-19
Printing example
Meaning
Remark
No.4165
Message name
Printing example
Meaning
Remark
No.4166
Message name
Printing example
Meaning
Action
Remark
No.4167
Message name
Printing example
Meaning
Cause
Remark
No.4168
Message name
Printing example
Meaning
Cause
No.4169
Message name
Printing example
2-20
Meaning
Cause
Action
No.4170
Message name
Printing example
Meaning
Cause
Part of data stored in flash memory was destroyed, or flash memory may be
faulty.
Action
If the SCS is in a single CPU module configuration, the SCS will not be able to
start when this CPU restarts next time. It is necessary to change the CPU
module right away.
If the SCS is configured with redundant CPU modules, the control will switch
to the other module after detecting this error, and the module where the error
occurs is restarted as a standby module.
If the error is caused by damage to the data in the flash memory, data in the
control side will be copied to the standby module where the error occurs, and
that module will then recover from abnormal to normal status.
If the error is caused by the physical damage of the flash memory, this system
alarm will occur even after the damaged CPU is switched to standby. Under
this circumstance, it is necessary to change the damaged CPU module.
No.4172
Message name
Printing example
Meaning
Cause
Action
Check and confirm that the total number of POU indicated in this message is
equal to the total number of POU indicated by Database Validity Check Tool.
No.4173
Message name
Printing example
Meaning
System database
Variable database
IM 32Q02B10-31E
Difference Data :
Cause
2-21
Difference data
When online change download from SENG to SCS was executed or the password was changed, data was normally written to flash memory.
No.4174
Message name
Printing example
Meaning
System database
Variable database
Difference Data :
Difference data
Cause
Action
If the SCS is in a single CPU module configuration, the CPU module continues
the operation even if this error occurs. However, the SCS will not start properly
when this CPU module restarts next time. It is necessary to change the CPU
module as soon as possible.
On a dual-redundant CPU module configuration SCS, if this writing error to
flush memory occurs on one of the CPU modules, the CPU module will be
failed and operation is continued with the other CPU module. It is necessary to
change the failed CPU module right away. If writing to the flash memories in
both CPU modules fails, the SCS will not be able to start when the CPU restarts. Under this circumstance, it is necessary to change both CPU modules
right away.
Remark
No.4175
Message name
Printing example
Meaning
Cause
The CPU processing time allocated for the external communication function
processing was not sufficient. As a result, processing to update the external
communication data is not performed.
Action
Reduce the communication load on the SCS. If this error occurs regularly, review the balance between the application logic amount and the scan period.
No.4177
Message name
2-22
Printing example
Meaning
Cause
Note
No.4178
Message name
Printing example
Meaning
Cause
Action
Remark
Note
SYS_SECURE FB
When the security level is 0, the message is not generated.
No.4179
Message name
Printing example
Meaning
Remark
Note
No.4180
Message name
Printing example
Meaning
Cause
Note
No.4181
Message name
Printing example
Meaning
Remark
2-23
No.4182
Message name
Printing example
Meaning
Remark
No.4183
Message name
Printing example
Meaning
Cause
This message is generated every time 12,000 events have occurred on the
SCS.
Action
Remark
Note
SOER function
This system alarm is generated even if SOE Viewer is started periodically.
Events can be uploaded from the SCS by starting SOE Viewer and displaying
the latest event.
No.4184
Message name
Printing example
Meaning
Action
Remark
Note
No.4185
Message name
Printing example 1
Printing example 2
Printing example 3
Printing example 4
Meaning
The value of the variable (VAR001 in the above example) was changed from
the SENG. For a communication I/O, a variable corresponds to the communication module location (as shown in example 2, node 1, slot 2) is also included
IM 32Q02B10-31E
2-24
in the message. For an I/O variable, a variable corresponds to the variable location (as shown in example 3, node 1, slot 2, channel 3) is also included in
the message.
The VAR001 in the above printing example 4 is the instance name of the function block that accesses the data of SCS Link Transmission. The related station number and bit number are also printed.
Remark
Forcing function
No.4186
Message name
Printing example
Meaning
Action
Remark
No.4187
Message name
Printing example
Meaning
Cause
Remark
No.4188
Message name
Printing example
Meaning
Remark
Download function
No.4189
Message name
Printing example
Meaning
Remark
No.4190
Message name
Printing example
Meaning
IM 32Q02B10-31E
2-25
Cause/Action
Cause
Action
5340-****
Others
Internal error
No.4191
Message name
Printing example
Meaning
No.4192
Message name
Printing example
Meaning
Action
Remark
No.4193
Message name
Printing example
Meaning
Cause
Remark
No.4194
Message name
Printing example
2-26
Meaning
Cause
Remark
The override enabled state continued exceeding the time limit (8 hours in the
above example) specified in SYS_OVR FB.
Check override FB in the override enabled state, and release unnecessary
override enabled state.
SYS_OVR FB
No.4195
Message name
Printing example
Meaning
Remark
No.4196
Message name
Printing example
Meaning
Cause
The password entered from the HIS and the password set in PASSWD FB did
not match.
Action
Remark
PASSWD FB
No.4197
Message name
Printing example
Meaning
Action
Remark
No.4198
Message name
Printing example
Meaning
Cause
Remark
IM 32Q02B10-31E
2-27
No.4199
Message name
Printing example
Meaning
Cause
A temporary communication error occurred, and the SCS detected the problem of the communication data.
Action
Remark
SYS_OVR FB
IM 32Q02B10-31E
3-1
3.
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-2
0094)>
3.1
No.0001
Message name
Printing example
Meaning
Cause
No.0003
Message name
Printing example
Meaning
Cause
No.0005
Message name
Printing example
Meaning
Cause
Note
No.0009
Message name
Printing example
Meaning
Cause
Action
The CPU module on the standby side takes over control. Replace the CPU
module that was stopped.
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-3
0094)>
No.0011
Message name
Printing example
Meaning
Cause
Causes
xxxxxxxx
SW STOP
-
V STOP
DC STOP
NSR3(*1)
CPU
module
stop
CPU
DOWN
INTSTS(*1)
ERRSTS1(*1)
ERRSTS2(*1)
SELFSTOP
UNKNOWN
(*2)
RESTART
*1:
*2:
Auto restart
Description
Stop by operation of the front switch of
the CPU module
No
No
No
Yes
No
No
Yes
If this error message is displayed, report the display contents of causes (xxxxxxxx) and code to Yokogawas service department.
Refer to the following Table 2.1-4 Error Codes and Solutions.
Error
Solution
Check to see if the application logic contains zero division or not, and correct the
application logic if it contains.
The database inconsistence is detected. It may be caused by restarting the SCS without releasing the
brake point.
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-4
0094)>
Table 3.1-2 Error Codes and Solutions (Table continued)
Code (hex; 16 digits)
Error
Solution
Other
Other
*1:
Action
No.0013
Message name
Printing example
Meaning
Cause
Note
No.0015
Message name
Printing example
Meaning
Action
No.0017
Message name
Printing example
Meaning
Action
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-5
0094)>
No.0021
Message name
Printing example
Meaning
Cause
Action
No.0023
Message name
Printing example
Meaning
Cause
There is a problem in the integration DB. Error indicates detailed error information.
Action
No.0025
Message name
Printing example
Meaning
Cause
Action
No.0027
Message name
Printing example
Meaning
Cause
The mapping block and the record block number do not match.
Action
Report the block type and record number where an error occurred to Yokogawas service department.
Note
No.0033
Message name
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-6
0094)>
Printing example
Meaning
Cause/Action
Error Contents
Cause
Action
9402
9403
9404
9405
Online change
downloading abnormal end
Others
Internal error
Internal error
No.0041
Message name
Printing example
Meaning
A cooling fan of the safety control station (station name = SCS0101) is abnormal. One of the following items is displayed in the parentheses in the above
example.
SCU N1: Left side fan
SCU N2: Right side fan
Cause
Action
Remark
HKU function
No.0042
Message name
Printing example
Meaning
Remark
No.0043
Message name
Printing example
Meaning
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-7
0094)>
AIR IN:
Air inlet
AIR OUT:
Air outlet
Cause
Action
After checking the operation of the cooling fans, report to Yokogawas service
department as necessary.
Remark
HKU function
No.0044
Message name
Printing example
Meaning
Remark
No.0045
Message name
Printing example
Meaning
Cause
Action
No.0046
Message name
Printing example
Meaning
No.0047
Message name
Printing example
Meaning
Cause
Action
Make sure that the switch of the applicable battery is ON. If the above message occurs even if the battery switch is ON, replace the battery.
Remark
HKU function
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-8
0094)>
No.0048
Message name
Printing example
Meaning
Remark
No.0055
Message name
Printing example
Meaning
Action
No.0057
Message name
Printing example
Meaning
Cause
This error occurs if error data cannot be saved on the safety control station
side.
Action
Note
No.0059
Message name
Printing example
Meaning
No.0063
Message name
Printing example
Meaning
Cause
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
0094)>
Action
3-9
Note
This message is generated if all the I/O nodes, excluding the CPU node, become abnormal.
However, if a system contains Optical ESB Bus Repeater module, when all the
I/O nodes directly connected to/from SEC402/SEC401 (i.e., the I/O nodes not
connected via Optical ESB Bus Repeater module), become abnormal, but the
I/O nodes connected via the Optical ESB Bus Repeater module are normal,
this message is not generated.
No.0064
Message name
Printing example
Meaning
No.0065
Message name
Printing example
Meaning
Cause
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-10
0094)>
For the I/O nodes that are connected via Optical ESB Bus Repeater module, the Optical ESB Bus Repeater module related hardware such as
module or Fiber-optic cable may have problem.
Action
If an I/O node routed through the Optical ESB Bus Repeater related devices
becomes abnormal, the erroneous device can be identified according to the
content of the messages or the LED status so as to replace the damaged device. If all the I/O nodes routed through the Optical ESB Bus Repeater related
devices become abnormal, the error may have occurred in the Optical ESB
Bus Repeater module related hardware such as module or Fiber-optic cable.
Moreover, if the Optical ESB Bus Repeater modules are mounted in the
SNT10D, the error may be caused by the failure of a power supply module of
SNT10D unit.
No.0066
Message name
Printing example
Meaning
No.0067
Message name
Printing example
Meaning
Cause
Action
Note
When the message shows node 1, it indicates that an error occurred in a PSU
for the CPU node.
No.0068
Message name
Printing example
Meaning
The power supply module of the I/O node indicated in the message (2 in the
above example) recovered normally. (This is a recovery message of No.
0067.)
No.0069
Message name
Printing example
Meaning
Cause/Action
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-11
0094)>
This message occurs when attempting to download to an IOM while another IOM download is still running. Only one IOM download can be performed at one time, so please wait for the other IOM download to complete before running an IOM download operation again.
A72C
Automatic IOM download to a standby side I/O module is running. This
error occurs if IOM download to the same I/O module is manually executed from the SENG or online change download is executed to make
changes in I/O parameter settings while automatic IOM download is running.
5135
This message occurs when attempting to download to an IOM even
though it is running normally.
Others
Report the error display content to Yokogawas service department.
No.0081
Message name
Printing example
Meaning
Cause
For more information about error codes, see the following table.
Action
Table 3.1-4 Error Details of Message No. 0081 - Errors of Analog Input Modules and Contact I/O Modules
Error code
Description of error
5101
The communication between CPU and I/O modules encounters a no-response error.
This error is caused either by the I/O module abnormality or by the communication
route abnormality.
5102
The type of the I/O module defined on the SENG and the type of the I/O module
mounted does not match. Check type of the I/O module.
5103
The setting information defined on the SENG and the I/O module setting information
do not match. Execute IOM download.
5104
A hardware error of the I/O module was detected. Check detailed error causes in the
IOM report.
5105
A setting error of the I/O module. Check detailed error causes in the IOM report (field
side connector disconnection, field power supply/wiring problem, etc.)
5106
The I/O module recovered from an error state. Check detailed error causes in the IOM
report.
5107
The error that actuated the output shutoff switch occurred. Check detailed error causes in the IOM report. When this error occurred, start the I/O module after recovering
from the error.
A communication data check error was detected between the CPU and the I/O module. A failure of the I/O module or a problem of the communication path up to the I/O
module may be the cause.
Continues on the next page
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-12
0094)>
Table 3.1-4 Error Details of Message No. 0081 - Errors of Analog Input Modules and Contact I/O Modules (Table continued)
Error code
Description of error
5114, 5115
An error was detected in the redundant control part of the I/O module. Replace the I/O
module.
However, when two I/O modules in single configuration are changed to dual-redundant configuration and online change download is performed, this error may be detected if a connector cable is plugged to only one of the two modules. In this case, plug
the connector cables to both modules. Recovery from this error is notified with system
alarm message No.0082 Normal recovery of I/O module, and there is no need to replace the I/O modules.
5116, 5117
5118
Table 3.1-5 Error Details of Message No.0081 Errors on ALR111/ALR121/ALE111 Modbus Slave and
ALE111 DNP3 Slave
Error Code
Cause/Action
C580
The communication between CPU and I/O modules encounters a no-response error.
This error may be caused by the I/O module abnormality, communication route abnormality or an abnormality other than C581 to C583 depicted.
C581
C582
The communication program in the communication module is not the program for
Modbus slave communication/DNP3 slave function. Run IOM download.
C583
The physically installed communication module shows a different model name from
the communication module defined in SENG. Check the model of the communication
module.
Cause/Action
A33D
No response from the communication module due to communication module abnormality. Change the communication module.
A33E
C581
C582
The communication program in the communication module is not the program for the
communication defined in SENG. Run IOM download.
C583
The physically installed communication module shows a different model name from
the communication module defined in SENG. Check the model of the communication
module.
C585
C598
The communication module is reset due to online change download or the IOM downloading.
C599
Downloading to database.
C59A
C5C1
Error found after resetting the communication module. Change the communication
module.
C5C6
Failed to download the communication program. Waiting time for shifting to the downloading mode of the communication program exceeded the time limit. Start IOM
download again.
C5C7
Failed to download the communication program. Processing time for downloading the
communication program exceeded the time limit. Start IOM download again.
C5E2
Communication module encountered an error and stopped. Change the communication module.
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-13
0094)>
No.0082
Message name
Printing example
Meaning
No.0083
Message name
Printing example
Meaning
Cause
Action
If this error occurred after replacing a module or at startup, the database might
not have been downloaded to the I/O module. Execute IOM download.
If this error occurred during I/O module operation, the I/O module may be faulty. Replace the I/O module.
No.0085
Message name
Printing example
Meaning
An error occurred in one of the SB buses (right side in the above example). An
error occurred when accessing the I/O module mounted in slot 1 of node 1 in
the safety control station (station name = SCS0101).
Cause
If this error occurred on all input modules within the same node, an I/O module
may be faulty, or the backboard bus of the node may be faulty. Or, an ESB bus
(right side in the above example) or an SSB401 (right side in the above example) may be faulty, or they may not be connected properly.
Action
No.0086
Message name
Printing example
Meaning
No.0087
Message name
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-14
0094)>
Printing example
Meaning
Cause
Action
No.0088
Message name
Printing example
Meaning
No.0089
Message name
Printing example
Meaning
Cause/Action
Table 3.1-7 Error Details of Message No.0089 - Errors that irrelevant to subsystems
Code
Error
Cause/Action
A391
Driver Busy
A392
A393
A394
A395
A397
Underrun
A398
This message occurs when the interval of characters exceeds the specified time.
Continues on the next page
IM 32Q02B10-31E
<3.1 Safety Control Station Error Occurrence and Recovery Messages (Message Numbers 0001 through
3-15
0094)>
Table 3.1-7 Error Details of Message No.0089 - Errors that irrelevant to subsystems (Table continued)
Code
Error
A399
A39A
A39B
Reception overrun
A39C
A39D
A39F
Other errors
A3B0 to
A3FF
*1:
Cause/Action
The transmission-watching timer monitors the waiting time of the transmission line become ready for transmission. When RS
is sent, and the waiting time for transmission exceeds the specified time period, the transmission becomes error. The transmission waiting time is normally set to 1000 ms.
The conditions for transmission are as follows:
CD line off (When CD check is enabled)
CS (CTS) line on
DR line on (When DR check is enabled)
Remark
Subsystem communication
No.0090
Message name
Printing example
Meaning
Remark
No.0093
Message name
Printing example
Meaning
Action
Remark
No.0094
Message name
Printing example
Meaning
Remark
IM 32Q02B10-31E
<3.2 Safety Control Station Status Change Related Messages (Message Numbers 0450 through 0480)>
3-16
3.2
No.0450
Message name
Printing example
Meaning
Cause
Copy program and database on control side of safety control station to standby side
SCS0101 Copy
The copying of the program and database on the control side of the safety
control station to the standby side has been started.
This message is displayed when the CPU module on the standby side of the
safety control station (station name = SCS0101) was started.
No.0451
Message name
Printing example
Meaning
No.0452
Message name
Printing example
Meaning
No.0459
Message name
Printing example
Meaning
No.0460
Message name
Printing example
Meaning
IM 32Q02B10-31E
<3.2 Safety Control Station Status Change Related Messages (Message Numbers 0450 through 0480)>
3-17
No.0471
Message name
Printing example
Meaning
No.0474
Message name
Printing example
Meaning
Action
No.0475
Message name
Printing example
Meaning
Database download to the I/O module indicated in the message has been started.
No.0476
Message name
Printing example
Meaning
Database download to the I/O module indicated in the message has normally
been completed.
No.0477
Message name
Printing example
Meaning
Cause/Action
An error occurred during database download to the I/O module indicated in the
message. xxxx indicates an error code.
The following lists error codes. If an error occurs, remove the cause, and execute IOM download again.
If an error other than the following occurred, replace the I/O module and execute IOM download again. If other error occurred again, report details to Yokogawas service department.
IM 32Q02B10-31E
<3.2 Safety Control Station Status Change Related Messages (Message Numbers 0450 through 0480)>
3-18
IOM error codes other than ALR111, ALR121, and ALE111.
A701: This I/O module is currently executing download.
3B1B: The I/O module is faulty.
CFxx: An error was replied from the I/O module.
CF10: The type of the I/O module is not correct.
Error codes of ALR111, ALR121, and ALE111
A33D: Communication cannot be performed with the ALR1x1 and
ALE111.
A33E: The communication path between the CPU module and the
ALR1x1 is abnormal. (Node failure, etc.)
A731: Simultaneous download attempts were made for communication
programs. In one attempt of the online change download,
ALR1x1 for subsystems, ALR1x1 for Modbus Slave, ALE111 for
Modbus/TCP Slave and ALE111 for DNP3 Slave are not allowed
to add simultaneously. If you try to add them simultaneously,
A731 error occurs when downloading is attempted for the second and subsequent modules. When an error occurs, perform
IOM download to the failed communication module on SCS State
Management Window after the online change download completes.
No.0480
Message name
Printing example
Meaning
Cause
Action
Correct the application and reduce the load on the safety control station.
IM 32Q02B10-31E
3-19
<3.3 Safety Control Station Related Messages (Message Numbers 0727 through 0787)>
3.3
No.0727
Message name
Printing example
Tag name
No.0743
Message name
Printing example
Meaning
Cause
There is a failure in the SEN-BUS in the CPU node or the CPU module mounted.
Action
No.0744
Message name
Printing example
Meaning
No.0749
Message name
Printing example
Meaning
Cause/Action
CODE = 0000511B :
IM 32Q02B10-31E
3-20
<3.3 Safety Control Station Related Messages (Message Numbers 0727 through 0787)>
A detail code of CODE = 0000511B. Y = 0 indicates an error in the right CPU module, and Y = 8
indicates an error in the left CPU module.
No.0750
Message name
Printing example
Meaning
No.0751
Message name
Printing example
Meaning
Cause
Action
No.0753
Message name
Printing example
Meaning
Communication Overload
SCS0101 Communication Overload
Communication load to safety control station exceeded the limit.
Cause
There were many communication demands from the operation and monitoring
function window or application programs to the safety control station.
Action
If the windows for the indicated safety control station are displayed on the
CENTUM HIS, the windows need to be closed. Modifying the application programs may also reduce the communication load to the safety control station.
No.0767
Message name
Printing example
Meaning
Cause
The CPU module or the backboard of the CPU node may be faulty.
Action
No.0768
Message name
Printing example
3-21
<3.3 Safety Control Station Related Messages (Message Numbers 0727 through 0787)>
Meaning
No.0787
Message name
Printing example
Meaning
Factor
0251 8000
0255 8082
xxxx0471
xxxx xxxx
xxxx0313
xxxx xxxx
*1:
IM 32Q02B10-31E
App.1-1
Message name
Alarm class
0001
0003
0005
0009
0011
0013
0015
0017
0021
0023
0025
0027
0033
0041
0042
0043
0044
0045
0046
0047
0048
0055
0057
0059
0063
1, or 2
0064
0065
1, or 2
0066
0067
1, or 2
0068
0069
1, or 2
0081
1, or 2
0082
0083
1, or 2
Continues on the next page
IM 32Q02B10-31E
App.1-2
Message name
Alarm class
0085
1, or 2
0086
0087
0088
0089
0090
0093
0094
0450
0451
0452
0459
0460
0471
0474
0475
0476
0477
0480
0727
0743
0744
0749
1, or 2
0750
0751
0753
Communication Overload
0767
0768
0787
1, or 2
4101
4102
4103
Variable lock
4104
4105
4106
4107
4108
4109
4110
4
Continues on the next page
IM 32Q02B10-31E
App.1-3
Message name
Alarm class
4111
4112
4113
4114
4115
Override setting
4116
Cancellation of override
4117
4118
4119
4120
4121
4122
4123
4124
4125
4126
4127
Setting PASSWD FB to ON
4128
4129
4130
4131
4132
4133
1, or 2
4134
4135
4136
4137
4138
4139
4140
4141
4142
4143
4144
4145
4146
4151
4
Continues on the next page
IM 32Q02B10-31E
App.1-4
Message name
Alarm class
4152
4153
4154
4155
4156
4157
4158
4159
4160
4161
4162
4163
4164
4165
4166
4167
4168
4169
4170
4172
4173
4174
4175
4177
4178
4179
4180
4181
4182
4183
4184
4185
4186
4187
4188
4189
4190
2
Continues on the next page
IM 32Q02B10-31E
App.1-5
Message name
Alarm class
4191
4192
4193
4194
4195
4196
4197
4198
4199
IM 32Q02B10-31E
Rev-1
Revision Information
Title
: Messages
No.0081, No.0477
No.4151
Appendix 1
No.4151 added.
Descriptions changed.
Appendix 1
Newly added.
IM 32Q02B10-31E