Lecture 16
Lecture 16
To explain intricacies of the problem, let us consider a radial system in the fig 16.1. Fault under
consideration is a 3 - phase fault. Relays used have Normal Inverse, IEC standard characteristics.
Coordination time interval CTI is 0.3sec. It is required that primary protection should fulfill its
responsibility within 1.0sec of the occurrence of fault.
The relays along with Circuit Breaker are labeled as R 1 , R 2 , R 3 , R 4 . The bus loads and fault currents are
tabulated in Table 1. It is obvious that pick up current settings for the relays should be above the feeder
load currents and not the bus load currents. In fact, one should consider the maximum possible loading
conditions, to decide conservatively pick-up current settings. A rule of thumb is to set the pick-up current
at 1.25 times maximum load current. Another 'rule of thumb' is to limit pick-up current to 2/3rd of the
minimum fault current. This decides the range available for setting relay pick-up.
Table 2 details the calculations associated with setting of overcurrent relays. It shows both the minimum
fault current and the maximum load current. Now ideally, one can set the pick up current of the
overcurrent relay anywhere within the maximum feeder load current (column 2) and minimum fault
current (column 3). However, as explained in the previous lecture, with electromechanical relays, we
should not allow PSM to be below 1.5. Since I p = If min/PSM, upper limit on PSM sets lower limit on I p ,
which is equal to
If min at PSM = 1.5. For example, pick up of relay R 1 can be set between 62.5 A
Maximum Load
bus A
50
250
500
bus B
50
650
1200
bus C
100
1100
2000
bus D
50
1600
3500
Now to decide the pick-up current of relay R 2 , it is not adequate to just look at the minimum fault current
of section CB. This is because, relay R 2 also has to back up the section BA in case relay R 1 or the its CB
or the associated circuitry fails. Hence, minimum fault current to be protected by relay R 2 is also 250 A.
Now one can choose pick up current of R 2 to be equal to R 1 . However, if we use same TMS setting for R 2
as R 1 then it leads to a serious conflict of interest between relays R 1 and R 2 with both of them competing
to clear the fault. If R 1 clears the fault F1 first, then there is absolutely no problem. But if R 2 clears the
fault first then, there is an unwanted loss of service to load at node B. This brings out another additional
requirement for relay R 2 viz. it should give preference to relay R 1 for faults on section BA. This can be
achieved in two ways:
1.
2.
Relay R 2 conservatively waits for a specified time for relay R 1 to act (time discrimination principle).
In the absence of the communication channel availability, alternative 2 is the only viable option.
(1)
(2)
(3)
Step 1
In this step, we will set relay R 1
Choose for relay R 1 TMS = 0.025. No intentional time delay is provided because R 1 does not have backup
responsibility.
Relay 1 (R1 )
As explained before, pickup current of R 1 = 160A.
For fault on section AB (Ifmax = 500 A):
PSM = Fault Current / Actual Pick up = 500/160 = 3.125
TMS = 0.025
Operating time using IEC SI TCC.
= 0.15sec
The corresponding point 'a' is marked on fig 16.2 (step 1). Now, the back-up protection for section AB is
given by relay 2. Setting of relay -2 is explained in the next step.
TMS
Now
PSM
with
= 0.07
for maximum fault current on section BC (1200A)
= Fault Current / Actual Pick up = 1200/167 = 7.185
TMS = 0.07 operating time of relay 2
We have emphasized earlier that CT and PT play a critical role in determining performance of relaying
system. We now evaluate their effect in performance of overcurrent relaying application.
16.3 Fault Type and CT burden
In the previous lectures on CT, we have discussed the effect of CT burden on the performance of CTs. But
in real life application, in three phase CT connection, the burden on individual CTs will vary with the type
of connection and the type of fault. This is summarized in Table 3.
Table 3 : Fault Type and Its Effects on CT burden
Type of fault
Connection
3 - Phase
Phase
or
Phase
to
Phase to Ground
Wye (connected at Z = R + R + Z
S
L
R
CT)
Z = R S+ 2RL + Z R
Z = R S+ 2RL + 2ZR
Z
RS
RL
ZR
16.4
3.
4.
Example
1.A
8
MVA,
138/13.8 KV
transformer is connected to an
infinite bus. If a bolted three
phase fault occurs at F, find out
the
fault
current.
The
impedance of the transformer
is 10% and location of the fault
is close to the bus as shown in
fig 16.4.
2.If the distribution feeder has
600/5 C 200 CT with a knee
point 100 Volt, calculate the
voltage developed across CT
and
comment
on
its
performance.
CT
secondary
resistance is 0.414 .
Assume that (1) CTs are star connected (2) Lead wire resistance is 0.411
and relay impedance is 0.259
.
If the existing 8 MVA transformer is replaced with a new 28 MVA transformer with 10% leakage
impedance, find out the
new fault current. Will this new fault current lead to CT saturation?
In case CT saturates, comment on the performance of
(a) Primary relay (b) back up relay (c) co-ordination between primary and back up relay pair.
Solution:
1.
= 3347A
16.4 Example
Solution:
2.
CT secondary current
To obtain conservative estimate of CT performance we will use this value. This amounts to assuming
bolted SLG fault current to be comparable to bolted 3 phase fault current. In comparison to three phase
fault, CT phases larger burden with S-L-G fault.
Since the secondary voltage, V S is less than knee point voltage the CT will not saturate.
3.
= 97.6
1.754 = 171.19 V
Since, the knee point is 100 V the CT will saturate at 171.19 V.
4.
a.
b.
c.
Because of CT saturation, the secondary current will be clipped. Thus, CT secondary current will reduce.
Hence, PSM will reduce and primary relay operation time will increase. This will slow down the operation of
primary overcurrent relay. But typically, the back up relays in a radial system will have higher ratio CTs
than the primary. Consequently, knee point voltage is also higher. This implies that the back up relay,
which does not saturate can act before the primary since, these CTs are generally less likely to saturate.
Hence, relay co-ordination may be lost.
This can be minimized by one of the following methods.
Additional co-ordination time can be included in the settings.
Set the instantaneous relay units below the current at which saturation begins.
Relays with less inverse time characteristics can be used upstream from the relay which has saturated
CTs. This
ensures a greater time margin at high currents when saturation is more likely.
Review Questions
1.
In a radial system if minimum fault current is less than or equal to maximum load current, can
overcurrent relay be used?
Why?
2.
3.
Calculate the burden on a delta connected CT for a three phase fault and S-L-G fault.
Recap