Professional Documents
Culture Documents
TM 11-5895-227-15 Department of The Army Technical
TM 11-5895-227-15 Department of The Army Technical
AN MSC-25
DEATH ON CONTACT
may result if safety precautions
are not observed.
EXTREMELY
DANGEROUS POTENTIALS
EXIST IN THE FOLLOWING UNITS:
POWER ENTRANCE panel 115 volts ac
Power distribution panel 115 volts ac
Teletypewriter TT-4(*)/TG 115 volts dc
Reperforator-Transmitter, Teletypewriter
TT-76 (*) /GGC 115 volts ac
Terminal, Telegraph TH-5/TG 350 volts dc
Intercommunications Station LS-147(*)/TG 270 volts de
WARNING
VENTILATION IS ESSENTIAL
To prevent asphyxiation, Operations Center, Communications AN/
MSC-25 must be ventilated at all times when occupied.
Change HEADQUARTERS
DEPARTMENT OF THE ARMY
No. 10 Washington, DC, 1 July 1989
Page 28, paragraph 18b(7). In line 2 "13through 25" is changed to read "18 through 25", and 18b(9) in line 5, "No. 13" is
changed to read "No. 18".
Add figure No. 43.2 "Operation Center Communications, AN/MSC-25 (Modified), Power Schematic Diagram" and figure
No. 43.3 "Operation Center Communications, AN/MSC-25A (Modified), Power Schematic Diagram", after figure No.
43.1.
1
TM 11-5895-227-15
C4
}
CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
No. 4 WASHINGTON, D.C., 2 December 1964
TM 11-5895-227-15, 24 April 1961, is changed as indicated so that the manual also applies to the following equipment:
1
TM 11-5895-227-15
Page 3, paragraph 6, chart. Delete this portion of the chart and substitute:
TAGO 760A
2
TM 11-5895-227-15
(d) Turn the lever on the receptacle (a) Simultaneously turn the receptacle
knurled collar counterclockwise until the collar just collar lever and the connector collar until the open
engages the cam. position is reached.
(e) Turn the knurled collar on the (b) Carefully pull the connectors apart.
connector clockwise until the sleeve just engages the (c) Replace the covers.
cam. Page 39, paragraph 27e. Delete the paragraph
(f) Simultaneously turn the receptacle heading and substitute:
collar lever and the connector collar until the closed Air Conditioner (TV-189/A1MC-2.5) (fig. 21).
position is reached.
Add paragraph e.1 after paragraph e.
(2) Disconnecting procedure. e.1. Air Conditioner (V-189A/MSC-25).
Page 41, paragraph 29d. Delete the paragraph CONTROL position if no external thermostatic switch
heading and substitute: has been installed.
Air Conditioner (V-189/MSC-25) (fig. 21). Caution: Do not leave the air
Add paragraph 29d.1 after paragraph 29d. conditioner unattended for more
d.1. Air Conditioner V-189A/MSC-25. than 1 hour in this condition.
Caution Page 42, paragraph 32b(4). Delete the heading
Open the air conditioner intake (fig. 7) and outlet and substitute:
(fig. 8) vents before operating the air conditioner. Air conditioner (V-189/MS-25).
(1) Starting for ventilation. Position the main
control knob to the VENTILATION position. Add subparagraph 32b(4.1) after subparagraph 32b(4).
(2) Starting for regulated cooling. Position (4.1) Air conditioner (V-189A/MSC-25).
the main control knob to the COOLING position. If an Turn the main control knob to OFF to stop all operations
external thermostatic switch has been installed, position of the air conditioner.
the main control knob to the EXTERNAL CONTROL Caution
position. Adjust thetemperature control knob on the Operate the main control knob to
external thermostatic switch to provide the desired OFF before operating circuit breaker
temperature in the space being cooled. switch No. 9 (AIR COND.) to off.
Note Page 44, paragraph 38, line 12. Change
At any given setting, either the "C189/MSC-2"to V-189(*) /MSC-25.
temperature control switch or the Page 55, paragraph 58a. At the end of
external thermostatic switch will subparagraphs (2) and (3), add (V-189/MSC-25 only).
automatically operate the air Page 62, paragraph 62a(1). Make the following
conditioner to maintain the van changes:
interior at the desired temperature. Line 3. Change "JS" to J1.
(3) Starting for constant unregulated cooling. Line 5. Change "J1"to J2.
Position the main control knob to the EXTERNAL,
TAGO 760A
3
TM 11-5895-227-15
Page 65, appendix I (page 7 of C3). After the Delete the WHT wire that connects DS38 and
reference "TM 9-213", add the following references: S11.
TM 5-4120-205-12 Operator and Organizational Add a wire between the right side of S11 and
Maintenance Manual: Air the left side of DS38. Indicate that the new wire
Conditioner: Floor Mtg; Air Cooled; has the same color coding and wire size as the
18,000 BTU. deleted wire.
TM 5-4120-205-20POperator and Organizational In the area of TH-5 TT-74, make the following
Maintenance Repair Parts and changes:
Special Tool Lists, Air Conditioner: Delete the BLK wire that connects DS39
Floor Mtg; Air Cooled; 18,000 BTU. and S12
Figure 43 (foldout). Make the following changes:
On the POWER ENTRANCE PANEL, change Delete the WHT wire that connects DS39
"IN POWER 115V AC OUT" to: OUT POWER 115V AC and S12.
IN. Add a wire between the right side of S12
In the center portion of the illustration, in the and the left side of DS39. Indicate that the
area of TH-5 TT-76, make the following changes: new wire has the same color coding and
wire size as the deleted wire.
Delete the BLK wire that connects DS38 and
S11.
By Order of the Secretary of the Army:
HAROLD K. JOHNSON,
General, United States Army,
Chief of Staff
Official:
J. C. LAMBERT,
Major General, United States Army,
The Adjutant General
Distribution:
Active Army:
USASA (2) Armies (2) Ft Huachuca (10)
CNFB (1) Corps (2) Army Tml (1) except
CC-E (7) USAC (3) OART (5)
CofT (1) 11th Air Astl Div (3) POE (1)
CofEngrs (1) Svc Colleges (2) Sig Fld Maint Shops (2)
TSG (1) Br Svc Sch (2) except AMS (1)
CofSptS (1) USASESCS (25) USAERDAA (2)
USAAESWBD (2) USATC AD (2) USAERDAW (13)
USARADBD (2) USATC Engr (2) Units organized under following
USAARMBD (2) USATC Inf (2) TOE's: (2 copies each unless
USAARTYBD (2) USASTC (2) otherwise indicated)
USACDC Agencies (1) USATC Armor (2) 11-16
USACDCCEA WRAMC (1) 11-32
(Monmouth Ofc) (1) Army Pic Cen (2) 11-57
USAMC (5) Army Dep (2) except 11-95
USCONARC (5) LXAD (14) SAAD (30) TOAD 11-96
ARADCOM (2) (14) FTWOAD (10) LEAD (5) 11-97
ARADCOM Rgn (2) SHAD (3) NAAD (5) CHAD 11-98
OS Maj Comd (3) (3) SVAD (5) ATAD (4) 11-117
LOGCOMD (2) GENDEP (2) 11-155
USAECOM (7) Sig Sec, GENDEP (5) 11-157
USAMICOM (4) Sig Dep (12) 11-500 (AA-AE) (4)
USASMC (2) Instl (2) except 11-557
USASCC (4) Ft Monmouth (63) 11-587
USAAVCOM (1) Ft Hancock (4) 11-592
MDW (1) Ft Gordon (5) 11-597
NG: State AG (3); units--same as active Army except allowance is one copy.
USAR: None.
For explanation of abbreviations used, see AR 320-50.
}
CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
No. 5 WASHINGTON, D.C., 23 February 1966
Note
The parenthetical reference to a previous change (example page 1 of C 4) indicates that pertinent
material was published in that change.
c. Reporting of Equipment Manual Improvements. This form will be completed using pencil, pen, or
The direct reporting by the individual user of errors, typewriter and forwarded direct to Commanding
omissions, and recommendations for improving this General, U.S. Army Electronics Command, ATTN:
manual is authorized and encouraged. DA Form 2028 AMSEL-MR-MP-P, Fort Monmouth, N. J. 07703.
(Recommended Changes to DA Publications) will be
used for reporting these improvement recommendations.
Page 65. Appendix I (page 4 of C 4). Add the following after the last reference:
SB 11-573 Painting and Preservation Supplies Available for Field Use for Electronics Command Equipment.
TB SIG 364 Field Instructions for Painting and Preserving Electronics Command Equipment.
TM 11-5935-203-15P Organizational, DS, GS, and Depot Maintenance Repair Parts and Special Tool Lists: Connectors,
Receptacle, Electrical U-186A/G and U-186B/G.
TM 11-6110-201-15P Operator, Organizational, Field and Depot Maintenance Repair Parts and Special Tool Lists and
Maintenance Allocation Chart: Distribution Boxes J-1077/U and J-1077A/U.
*This change supersedes C1, 3 April 1962, and TM 11-5895-227-25P, 22 March 1962, including C2, 21 August
1963.
TAGO 6571-A
1
TM 11-5895-227-15
APPENDIX II
Section I. INTRODUCTION
TAGO 6571-A
2
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
TS TI ILLUSTRATIONS
S IZ
FEDERAL OU TE FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
NOTE
For maintainable equipments listed below, only two each technical
manuals are authorized.
NOTE
Model column 1 refers to V-189/MSC-25 procured from St. Carl on order No.
3131-PP-59; Column 2 refers to V-189A/MSC-25 procured from North
Electric Co. on order No. 7302-PP-64.
4120-892-1989 † AIR CONDITIONER: Ellis and Watts p/n A-18 1
4210-727-8111 † † AXE, FIREMAN: Approx 2-3/4 lb, 24'' handle, Fed Spec GGG-A-926, Type 1, 1
Class 1, Design B
4210-764-2905 † † AXE, PICKHEAD: Approx 3-1/2 1 bx, 36'' handle; Fed Spec GGG-A-926, Type 1 1
Class 1, Design B
AGO 6571-A
3
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
†S †I ILLUSTRATIONS
S IZ
FEDERAL OU †E FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
AN/ASC-25 (continued)
5995-823-2620 † † CABLE ASSEMBLY, SPECIAL PURPOSE: f/headset; approx 8 ft lg; Sig dwg 2
SM-C-382135
5995-889-0923 † † CABLE ASSEMBLY, TELEPHONE: Stub for SB-22/PT; Sig dwg SM-C-353715 1
5995-823-2955 † † CABLE ASSEMBLY, TELEPHONE: Approx 6 ft lg; PJ-047B one end, other end 8
stripped and tinned; Sig dwg SM-C-377563-V
5995-823-3016 † † CABLE ASSEMBLY, TELEPHONE: 2 cond; approx 6 ft lg; PJ-055B one end; Sig 1
dwg SM-D-384145-I
5995-823-0608 † † CABLE ASSEMBLY, TELEPHONE: 2 cond; approx 6 ft lg; PJ-055R one end; Sig 1
dwg SM-D-384145-II
5995-752-2512 † † CABLE ASSEMBLY, TELEPHONE: 2 cond; approx 2 ft lg; plug each end; Sig 8
dwg SM-D-352593-II
7105-268-8214 † † CHAIR, FOLDING: Metal; w/o arms; Fed Spec AA-291a, Type 1, Class 1 2
7110-273-8798 † † CHAIR, ROTARY: Fed Spec AA-C-295, Class 1, Size 1; (NOTE: When replacing 5
remove mfg bracket f/use on new chair)
7110-281-4469 † † CHAIR, ROTARY: Drafting stool; Fed Spec AA-C-295, Class 2, Size 3; 1
(NOTE: When replacing, remove mtg bracket f/use on new chair)
TAGO 6571-A
4
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
†S †I ILLUSTRATIONS
S IZ
FEDERAL OU †E FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
AN/MSC-25 (continued)
4210-223-9912 † EXTINGUISHER, FIRE: Carbon dioxide type; MIL type MIL-E-468-CE; type .1, NX 3
class 1
6545-663-9032 † † FIRST AID KIT: Fed Spec GG-K-392, type II, size 1 1
TAGO 6571-A
5
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
†S †I ILLUSTRATIONS
S IZ
FEDERAL OU †E FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
AN/MSC-25 (continued)
5120-752-9675 † † SCREWDRIVER, FLAT TIP: Bridgeport Hwd Mfr Corp p/n 2143-6 2
TAGO 6571-A
6
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
†S †I ILLUSTRATIONS
S IZ
FEDERAL OU †E FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
AN/MSC-25 (continued)
5920-581-4144 † † FUSE, CARTRIDGE: 2 amp, 250 v: Buss type MDX-2 (2 mtd in equip) 7
6240-155-8706 † † LAMP, INCANDESCENT: 6 to 8 v, 0.15 amp; MIL Std MS1557112, type TB-14 1
TAGO 6571-A
7
SECTION II. FUNCTIONAL PARTS LIST
DESIGNATION A
BY U
MODEL QT
U UH
N AO
II NR
†S †I ILLUSTRATIONS
S IZ
FEDERAL OU †E FIGURE ITEM
STOCK NUMBER DESCRIPTION FE EXP YD NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
8
Page 72, appendix III (page 9 of C 3). Delete appendix III and substitute:
APPENDIX III
MAINTENANCE ALLOCATION
Section I. INTRODUCTION
TAGO 6571-A
9
(4) Tools required. This column indicates maintenance equipment required to
codes assigned to each individual tool perform the maintenance functions.
equipment, test equipment, and (2) Operator, organization, direct support,
maintenance equipment referenced. The general support and depot. The dagger
grouping of codes in this column of the (†) symbol indicates the categories
maintenance allocation chart indicates the normally allocated the facility.
tool, test, and maintenance equipment (3) Tool code. This column lists the tool code
required to perform the maintenance assigned.
function. 2. Maintenance by Using Organizations
(5) Remarks. Entries in this column will be When this equipment is used by signal services
utilized when necessary to clarify any of organizations organic to theater headquarters or
the data cited in the preceding column. communication zones to provide theater
c. Columns in the allocation of tools for communications, those maintenance functions allocated
maintenance functions are as follows: up to and including general support are authorized to the
(1) Tools required for maintenance functions. organization operating this equipment.
This column lists tools, test, and
TAGO 6571-A
10
Section II. MAINTENANCE ALLOCATION CHART
MAINTENANCE ECHELON TOOLS
PART OR COMPONENT FUNCTION O/C O DS GS S REQUIRED REMARKS
COMMUNICATIONS OPERATIONS CENTER AN/MSC-25 service X Van facility & exterior of components
inspect X
test X System operation using built-in facilities
X 1,4,6 Continuity checks of signal,
lighting and power circuits
except 26 pair cable
X 2,4,5,6 Test in accordance with component
maintenance allocation chart
X 2,3,4,5,6 Test in accordance with component
maintenance allocation chart
repair X Repair as determined by component
maintenance allocation chart
X 4,5,6 Repair as determined by component
maintenance allocation chart
X 4,5,6 Repair as determined by component
maintenance allocation chart
X 4,5,6 Repair as determined by component
maintenance allocation chart
overhaul X 5 Overhaul by component
SEMI-TRAILER, VAN, ELECTRICAL EQUIPMENT service X Facility & exterior of components
V-189/MSC-25 inspect X
test X 1,4,6 Continuity checks of power and
lighting circuits except 26
pair cable
X 2,3,4,5,6 All tests
repair X 4,5,6 Except door panel, gaskets, molding
strip replacement and cable
connector
X 4,5,6 Except door panel and 26 pair
connector
X 4,5,6 All repairs
CABLE ASSEMBLY CX-4566/G test X 2,3
replace X
repair X 4
CONNECTOR; PLUG, ELECTRICAL U-185A/G test X 2
repair X 4 For maintenance allowances see
TM 11-5935-212-15P
CABLE ASSEMBLIES, POWER test X 1
repair X 4
TAGO 6571-A
11
Section II. MAINTENANCE ALLOCATION CHART
MAINTENANCE ECHELON TOOLS
PART OR COMPONENT FUNCTION O/C O DS GS S REQUIRED REMARKS
AN/MSC-25 (continued)
TELETYPEWRITER SET AN/GGC-3A and REPERFORATOR repair See TM 11-2225 for maintenance
TRANSMITTERS, TELETYPEWRITER TT-76, A, B/GGC allocations
TAGO 6571-A
12
Section II. MAINTENANCE ALLOCATION CHART
ECHELON TOOLS
PART OR COMPONENT O/C O DS GS S CODE REMARKS
AN/MSC-25 (continued)
MULTIMETER AN/URM-105 † 1
MULTIMETER TS-352/U † † † 2
OHMMETER ZM-21A/U † † 3
TOOL & TEST EQUIPMENT ASSOCIATED WITH COMPONENTS OF † † † † 6 Allocation based on separate MAC'S
END EQUIPMENT
NOTE: DEPOT MAY USE ANY OTHER TYPE OF TOOL & TEST
EQUIPMENT REQUIRED TO OVERHAUL THIS EQUIPMENT
TAGO 6571-A
13
Add Appendix IV after Appendix III.
APPENDIX IV
TAGO 6571-A
14
initial stockage for use in the direct 3. Additional Repair Parts Authorization
support maintenance and in supply An asterisk (*) indicates that an item is not authorized
support to organization. The quantities for stockage but if required, may be requisitioned for
are based on 100 equipments to be immediate use only.
maintained for a 15-day period. 4. Requisitioning Information (DS, GS and Depot)
(10) General support. The numbers in this a. The allowance factors are based on 100
column indicate quantities of repair parts equipments. In order to determine the number of parts
authorized for initial stockage for use in authorized for initial stockage for the specific number of
general support maintenance. The equipments supported, the following formula will be
quantities are based on 100 equipments used and carried out to two decimal places. Specific
to be maintained for a 15-day period. number of equipments supported
(11) Depot. The numbers in this column allowance factor
indicate quantities of repair parts X 100 =
authorized for depot maintenance and for
Number of parts authorized for initial stockage.
initial stockage for maintenance, and for
supply support to lower categories. The b. Fractional values obtained from above
entries are based on the quantity required computation will be rounded to whole numbers as
for rebuild of 100 equipments. follows:
(12) Illustration. The "Item No." column lists (1) When the total number of parts authorized
the reference symbols used for is less than 0.5, the quantity authorized
identification of the items in the illustration will be zero.
or text of the manual. (2) When the total number of parts authorized
is between 0.5 and 1.0, the quantity
2. Parts for Maintenance authorized will be one.
When this equipment is used by signal service (3) For all values above one, fractional
organizations organic to the theater headquarters or values below 0.5 will revert to the next
communication zones to provide theater lower whole number and fractional value
communications, those repair parts authorized up to and 0.5 and above will advance to the next
including general support are authorized for stockage by higher whole number.
the organization operating this equipment. c. The quantities determined in accordance with
the above computation represent the initial stockage for
a 15-day period.
TAGO 6571-A
15
SECTION II. ORGANIZATIONAL FUNCTIONAL PARTS LIST
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATIONS
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
TAGO 6571-A
16
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATIONS
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
AN/MSC-25 (continued)
5995-889-0608 / / CABLE ASSEMBLY, TELEPHONE: 2 cond; approx 6 ft lg; PJ-055R one end; 1 *
Sig dwg SM-D-384145-II
5995-752-2512 / / CABLE assembly, telephone: 2 cond; approx 2 ft lg; plug each end; 8 *
Sig dwg SM-D-353593-II
5940-254-2244 / / CAP, ELECTRICAL: black, f/U-106/U; Sig dwg SC-C-76202-1 56 *
5910-880-6898 / CAPACITOR, FIXED, PAPER DIELECTRIC: 1 sect, 5 uf, ±10%, 330 vac; 1 *
1.313 in d X 3.093 in h X 2.000 in w; GE part No. 49F3319
5910-553-6096 / / CAPACITOR, FIXED, PAPER DIELECTRIC: 3 sect; ea sect 10,000 uuf ±10%; 22 *
Hopkins type No. 591A
5910-713-8313 / CAPACITOR, FIXED, PAPER DIELECTRIC: 4 uf ±10%; Aerovox part No. 1 *
P150F83
5925-752-6642 / / CIRCUIT BREAKER: air arc quenching; dpst; Square D Cat No. Q0-270 1 *
5930-734-5202 / / CIRCUIT BREAKER: air arc quenching; spst; CH part No. 10172H334A 4 *
5925-682-1061 / / CIRCUIT BREAKER: air arc quenching; spst; Square D Car No. Q0-115 8 *
5925-823-2485 / / CIRCUIT BREAKER: air arc quenching; spst; Square D Car No. Q0150 1 *
5925-523-5764 / / CIRCUIT BREAKER: air arc quenching; Square D Cat No. Q0-120 5 *
5975-705-5841 / / CLIP, RETAINING: holds cable in cradle clamps; neoprene; 1-5/8 in 110 *
lg X 1 in w X 1/8 in thk; Electrovert part N3
5340-884-9983 / / CLIP, RETAINING: secures cable to cradle clips; 3.179 in lg X 1 in 14 *
w X 0.135 in thk; electrovert part N7
6645-752-7902 / CLOCK: MIL type MIL-C-3956 AN5743 M2 1 *
6645-892-4369 / / CLOCK, WALL: MIL spec MIL-C-1194, type A 1 *
5935-429-5511 / CONNECTOR, PLUG, ELECTRICAL: 2 cont; Hubbell part No. 7102 4 *
5935-646-5908 / / CONNECTOR, PLUG, ELECTRICAL: 2 cont; Hubbell part No. 9754 1 *
5935-064-5731 / / CONNECTOR, PLUG, ELECTRICAL U-237/G: f/power cables 3 *
5935-518-9653 / CONNECTOR, PLUG, ELECTRICAL UP-120M; f/heater 4 *
TAGO 6571-A
17
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATIONS
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
AN/MSC-25 (continued)
5895-856-5179 / / GEAR, DRIVE: P/o operations board screen; Sig dwg SM-B-378535 3 *
5120-776-9918 / / GRIP, CABLE, JAW: Economy Cable part No. EQA26-S 44 *
5120-776-9917 / / GRIP, CABLE, JAW: Economy Cable part No. EQA6-8P 6 *
TAGO 6571-A
18
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATIONS
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
19
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATION S
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
AN/MSC-25 (continued)
5940-823-1806 / / POST, BINDING: Standard Electric Time part No. GJ-5M black 2 *
5945-615-7738 / / RELAY, SWITCH: dpdt; Potter and Brumfield part No. PR11AY 1 *
5410-793-2021 / / REPAIR KIT, ELECTRONIC EQUIPMENT, SHELTER MRK-680/G: to repair A/R
punctures to shelter skin; (NOTE: To be requisitioned for
immediate use only, order direct from depot stock.)
/ / RETAINER, LAMP, FLUORESCENT: retains lamps in sockets; Laduby part 44 *
P-40 (M4CW10-B226)
5975-224-5260 / / ROD, GROUND MX-148/G: 2 *
5895-856-5178 / / SCREEN, OPERATIONS BOARD: Sig dwg SM-C-378530 3 *
6210-754-8134 / / SHIELD, LIGHT: f/fluorescent; Sig dwg SM-C-349983 22 *
6250-299-2884 / / STARTER, FLUORESCENT: GE part No. FS-2 22 *
5895-885-8612 / / STRAP WEBBING: 18 in lg; Davis Aircraft part FDC-1730-57-7 2 *
/ / STRAP, WEBBING: 18 in lg; Davis Aircraft part FDC-1730-58-3 3 *
(M4CW30-A073)
STRAP, WEBBING: 36 in lg; Davis Aircraft part FDC-1730-57-10 1 *
(M4CW30-A274)
5340-823-5234 / / STRAP, WEBBING: 37 in lg; Davis Aircraft part FDC-1730-58-2 4 *
/ STRAP, WEBBING: 52 in lg; Davis Aircraft part FDC-1730-56-1 1 *
(M4CW30-A775)
/ STRAP, WEBBING: 84 in lg; Davis Aircraft part FDC-1730-57-12 1 *
(MCW30-A275)
5340-823-5232 / STRAP, WEBBING: 24 in lg X 1 in w; Davis Aircraft part No. 1 *
FDC-1730-58-1
5340-823-5261 / / STRAP, WEBBING: 24 in lg X 1 in w; Davis Aircraft part No. 1 *
FDC-1730-56-3
5340-823-5262 / / STRAP, WEBBING: 32 in lg X 1 in w; Davis Aircraft part No. 1 *
FDC-1730-57-2
TAGO 6571-A
20
DESIGNATION A O
BY U R
MODEL Q T G
U U H A
N A O N
I I N R I
T S T I Z ILLUSTRATIONS
S I Z A
FEDERAL OU T E T FIGURE ITEM
STOCK NUMBER DESCRIPTION F E EXP Y D I NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
21
SECTION III. DIRECT AND GENERAL SUPPORT AND DEPOT FUNCTIONAL PARTS LIST
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
OPERATIONS CENTER, COMMUNICATIONS AN/MSC-25
5895-021-2088 OPERATIONS CENTER, COMMUNICATIONS AN/MSC-25: NX
designed as mobile installation in Trailer
V-51/G; providing tel and interphone come
facilities; 115 v, 230 vac simultaneously,
60 cyc, single ph
SEMITRAILER, VAN, ELECTRICAL V-189/MSC-25,
V-189A/MSC-25
NOTE: Model Column 1 refers to
V-189/M)C-25; Column 2 refers to V-189A/MSC-25
O 5410-792-6335 / / ADAPTER, TIE DOWN FLOOR: Davis Aircraft 12 6.5 3.6 120.0
part No. FDC-1225W5
O 5805-856-0797 / / ADAPTER, TIE DOWN FLOOR: Davis Aircraft 13 6.5 3.6 130.0
part No. FDC-1225M8-1
O 6625-752-8464 / / Am R: 0-100 amp; MIL type MR36WOOACMAAR 1 2.6 1.3 5.0
O 6250-500-4845 / / BALLAST LAMP: GE part No. 89G-457 22 9.4 5.5 44.0
O 6350-193-2776 / / BELL, ELECTRICAL: non adj; Edwards part No. 1 1.6 0.5 2.0.
156
O 7920-291-8305 / / BROOM, UPRIGHT: Fed Spec H-B-51, class 1, 1 1.9 1.0 3.0
type C
O 7920-178-8315 / / BRUSH, DUSTING, BENCH: Fed Spec H-B-201, 1 1.9 1.0 3.0
class B
O 6145-752-2562 / / CABLE, POWER, ELECTRICAL: 2 16AWG cond; GE ft 24 * * 240.0
part No. S1-5325 type 65/.0063 (Authorized
allowances will be a minimum of or a
multiple of 6 ft.)
O 6145-985-7704 / / CABLE, POWER, ELECTRICAL: 2 16AWG cond; MIL ft 2 * * 20.0
type CO-02kiF(2/16)0338 (Authorized
allowances will be a minimum of or a
multiple of 2 ft.)
O 6145-752-2473 / / CABLE, POWER, ELECTRICAL: 3 cond; Sig dwg ft 115 * * 1150.0
SC-A-46608; (Authorized allowances will be
a minimum of or a multiple of 115 ft.)
TAGO 6571-A
22
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
23
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
O 5930-734-5202 / / CIRCUIT BREAKER: air arc quenching; spst; 4 3.7 1.2 24.0
f/heater; CH part No. 101712H334A
O 5925-682-1061 / / CIRCUIT BREAKER: air arc quenching; spst; 8 6.5 3.6 48.0 CB1 thru
Square D Cat No.Q0-115 CB8
O 5925-823-2485 / / CIRCUIT BREAKER: air arc quenching; spst; 1 1.9 1.0 6.0 CB9
Square D Cat No. Q0-150
O 5925-523-5764 / / CIRCUIT BREAKER: air arc quenching; Square 5 4.8 2.6 30.0 CB10 thru
D Cat No. Q0-120
O 5975-705-5841 / / CLIP, RETAINING: holds cable in cradle 110 16.5 10.5 1100.0
clamps; 1-5/8 in lg X 1 in w X 1/8 in thk;
Electrovert part N3
O 5340-884-9983 / / CLIP, RETAINING: secures cable to cradle 14 4.8 2.6 140.0
clips; 3.179 in lg X 1 in w X 0.135 in thk
Electrovert part N7
O 6645-752-7902 / CLOCK: MIL TYPE MIL-C-3956, AN 5743-M2
O 6645-892-4369 / CLOCK, WALL: MIL spec MIL-c-1194, type A 1 1.9 1.0 5.0
F 5935-283-2950 / / CONNECTOR, PLUG U-77/7: f/headset extension 2 2.9 0.8 10.0
cord
F 5935-283-2884 / / CONNECTOR, PLUG U-78/U; f/headset extension 2 2.9 0.8 10.0
cord
P H 5935-045-9830 / / CONNECTOR, PLUG, ELECTRICAL U-185B/G; u/w 3 2.0 15.0
CX-4566A/G and CX-4760A/U
O 5935-429-5511 / CONNECTOR, PLUG, ELECTRICAL: f/heater; 2 4 3.7 1.2 20.0
CONT; Hubbell part No. 7102
O 5935-646-5908 / / CONNECTOR, PLUG, ELECTRICAL; f/exhaust fan; 1 1.9 1.0 6.0
2 cont; Hubbell part No. 9754
O 5935-518-9653 / / CONNECTOR, PLUG, ELECTRICAL UP-120/M; 4 3.7 1.2 20.0
f/heater
O 5935-836-1417 / / CONNECTOR, PLUG, ELECTRICAL: f/SB-22/PT 1 1. 0.6 5.0
cable stub; MIL type MS3116B16-26P
TAGO 6571-A
GPO 820-078-2
24
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
O 5935-064-5732 / / CONNECTOR, RECEPTACLE, ELECTRICAL U-238/G: 2 2.9 0.8 10.0
in power entrance box
O 5935-827-1545 / / CONNECTOR, RECEPTACLE, ELECTRICAL: 2 3.9 1.5 10.0 J32,J33
f/SB-22/PT cable assy; MIL type
MS3112E16-268
H 5935-682-0381 / / CONNECTOR, RECEPTACLE, ELECTRICAL U-187/G, 1 0.6 5.0
U-187A/G; 26 PAIR
O 5935-359-6025 / / CONNECTOR, RECEPTACLE, ELECTRICAL: 2 cont; 7 5.7 3.1 35.0 J7,J8,J16
Hubbell part No. 9210 thru J20
O 5935-549-3562 / / CONNECTOR, RECEPTACLE, ELECTRICAL: duplex 11 7.3 4.2 50.0 J3,J5,J6,
Hubbell part No. 9200 J9 thru J15
O 5805-871-5703 / / DOOR, FOLDING: Holcombe and Hoke part 1 1.6 0.8 2.0
2F2385
O 5120-293-2692 / / EXTRACTOR, ELECTRON TUBE: Economy Cable 1 1.6 0.5 5.0
part No. EETP-9
O 5120-752-8862 / / EXTRACTOR, ELECTRON TUBE: Economy Cable 1 1.6 0.5 5.0
part No. ETP-7
O 6210-855-9091 / FIXTURE, LIGHT: Specialty Electronics part 10 5.7 3.1 20.0
No. 3-24BM
O / FIXTURE, LIGHT: Electrospace Corp part No. 10 5.7 3.1 20.0
EST-184 (M4CW10-B257)
O 5920-014-2630 / / FUSE, CARTRIDGE: f/relay 5 amp; MIL Std 1 25.0 9.9 200.0
MS-90080-1
O 5920-686-0021 / / FUSEHOLDER: Buss type HKL 1 1.6 0.5 2.0
O 5895-856-5179 / / GEAR, DRIVE: p/o operations board screen; 3 1.9 1.0 5.0
Sig dwg SM-B-378535
O 5120-776-9918 / / GRIP, CABLE, JAW: Economy Cable part No. 44 45.1 19.5 880.0
EQA26-S
O 5120-776-9917 / / GRIP, CABLE, JAW: Economy Cable part No. 6 11.5 4.0 120.0
EQA6-8P
O 5120-251-4489 / / HAMMER, HAND: Fed Spec GGG-H-86, type SA, 1 2.6 1.2 5.0
class II
TAGO 6571-A
25
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/SC-25 (continued)
O 4540-404-9232 / / HEATING, ELEMENT, ELECTRICAL: 110 v, 1.5 kw; 4 3.7 1.2 12.0
Electromode part No. 3954-E
O 5965-892-3201 / / HOOK, HEADSET: Tiebout part No. 5565-1 9 3.6 1.1 27.0
O 4140-855-9079 / IMPELLER, FAN, AXIAL: 5 blades; Rotron part 1 1.9 0.6 3.0
No. 12706-1
O 4520-792-8398 / / IMPELLER, FAN, AXIAL: Torrington part No. 20 4 3.7 1.2 12.0
O 5935-192-4826 / / JACK, TELEPHONE: Cont arr J1; MIL type. JJ-086 18 4.8 1.5 180.0
O 5935-228-4038 / / JACK, TELEPHONE: Cont arr J4-2B; MIL type 46 9.4 3.3 460.0
JJ-085
O 6210-665-5376 / / KNOB: for fuseholder; Adler part No. 1
6279-1/2
O 5355-614-0400 / / KNOB: MIL Std MS91531-3N2M 13 1 .9 01. 5.0
O 6240-044-6914 / / LAMP, INCANDESCENT: MIL Std M35478-10 3 7.3 2.5 150.0 DS1,DS2,
DS3
O 6250-158-8918 / / LAMPHOLDER: Dialco part No. 6-08 2 1.6 0.5 10.0 DS38,DS39
O 6250-299-6093 / / LAMPHOLDER: f/fluorescent; Hubbell part No. 22 5.7 3.1 110.0
2937
O 6250-299-6697 / / LAMPHOLDER: f/fluorescent; Hubbell part No. 22 5.7 3.1 110.0
2943
O 6250-752-1233 / / LAMPHOLDER: f/NE-45; Leecraft part No. 15 13.0 7.8 750.0
4-74-6
O 6250-892-4365 / / LAMPHOLDER: Leviton part No.9062 2 1.6 0.5 10.0 DS4,DS5
O 6230-729-9614 / / LANTERN, ELECTRIC: Justrite part No. 2106-7 2 3.7 2.0 20.0
TAGO 6571-A
26
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
O 5410-752-2525 / / LEAD, ELECTRICAL: grd strap; Sig dvg 2 5.7 1.8 20.0
SM-B-352166
O 6230-615-5384 / / LIGHT, EXTENSION: Woodhead part 1
506KXS25-18-2SJ
F 5410-897-7588 / / LOUVER, METAL: Sig dwg SM-D-383846 2 2.3 0.6 4.0
F 5935-752-6011 / / MAINTENANCE KIT, ELECTRONIC EQUIPMENT: 1 1.9 o.6 3.0
f/maint of Connector, Plug U-77/U; Sig
dwgs Nos: SC-B-68419, SC-B-68420,
SC-B-68424, SC-B-68421, SC-B-68429,
Ns-35537-78
5410-973-2936 / / MAINTENANCE KIT, ELECTRONIC EQUIPMENT A/R *
SHELTER MK-679/G: to repair punctures to
shelter skin; (NOTE: to be requisitioned
for immediate use only, order direct from
depot stock)
O 6625-841-6641 / / METER, ELECTRICAL FREQUENCY: JBT Instrument 1 2.6 1.3 5.0
part No. 31FEX type I
O 6105-560-5739 / / MOTOR, ALTERNATING CURRENT: GE part No. 4 3.7 1.2 12.0
5KSP51AL74
O 6105-792-8384 / / MOTOR, ALTERNATING CURRENT: Rotron part No. 1 2.3 0.6 3.0
23396-01
O 5940-223-5293 / / POST, BINDING: U-106/U 56 11.0 6.3 560.0
O 5940-823-1805 / / POST, BINDING: Standard Elec Time part No. 2 1.1 0.5 10.0
BJ-5M-Red
O 5940-823-1806 / / POST, BINDING: Standard Electric Time part 2 1.1 0.5 10.0
No. BJ-5M-Black
O 5945-615-7738 / / RELAY, SWITCH: dpdt; Potter and Brumfield 1 1.9 1.0 3.0
part No. PR11AY
5410-771-3354 / / REPAIR KIT, ELECTRONIC EQUIPMENT, SHELTER A/R *
MK-681/G: to repair punctures to shelter
skin; (NOTE: to be requisitioned for
immediate use only, order direct from
depot stock)'
O / / RETAINER, LAMP, FLUORESCENT: retains lamps 44 9.4 5.5 440.0
in sockets; Laduby part P-40 (M4CW10-B226)
TAGO 6571-A
27
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
28
ILLUS-
DESIGNATION UNIT EXP QTY DIRECT GENERAL TRATION
SOURCE FEDERAL BY DESCRIPTION OF IN SUPPORT SUPPORT DEPOT
CODE STOCK NO. MODEL ISSUE UNIT
FIG. ITEM
A B C D NO. NO.
AN/MSC-25 (continued)
TAGO 6571-A
29
By Order of the Secretary of the Army:
HAROLD K. JOHNSON,
General, United States Army,
Chief of Staff.
Official:
J.C. LAMBERT,
Major General, United States Army,
The Adjutant General
Distribution:
Active Army:
USASA (2) USATC Engr (2)
CNGB (1) USATC Inf (2)
OCC-E (7) USASTC (2)
Dir of Trans (1) WRAMC (1)
CofEngrs (1) Army Pic Cen (2)
TSG (1) USACDCEC (10)
CofSptS (1) Instl (2) except
USACDCEA (1) Ft Monmouth (70)
USACDCCBRA (1) Ft Hancock (4)
USACDCCEA (1) Ft Gordon (10)
USACDCCEA Ft Huachuca (10)
Ft Huachuca (1) WSMR (5)
USACDCOA (1) Ft Carson (25)
USADCQMA (1) Ft Knox (12)
USACDCTA (1) Army Dep (2) except
USACDCADA (1) LBAD (14)
USACDCARMA (1) SAAD (30)
USACDCAVNA (1) TOAD (14)
USACDCARTYA (1) FTWOAD (10)
USACDCSWA (1) LEAD (7)
USAMC (5) SHAD (3)
USCONARC (5) NAAD (5)
ARADCOM (5) SVAD (5)
ARADCOM Rgn (2) CHAD (3)
OS Maj Comd (4) except ATAD (10)
USAREUR (5) GENDEP (OS) (2)
LGOCOMD (2) Sig Sec, GENDEP (OS) (5)
USAMICOM (4) Sig Dep (OS) (12)
USASMC (2) Sig Fld Maint Shops (2)
USASCC (4) AMS (1)
USAERDAA (2)
Armies (2) USAERDAW (13)
Corps (2) USACRREL (2)
USAC (3) Units org under fol TOE:
11th Air aslt Dive (3) 11-16 (2) 11-96 (2) 11-127 (2) 11-587 (2)
Svc Colleges (2) 11-32 (2) 11-97 (2) 11-155 (2) 11-592 (2)
Br Svc Sch (2) except 11-57 (2) 11-98 (2) 11-157 (2) 11-597 (2)
USASESCS (25) 11-95 (2) 11-117 (2) 11-158 (2)
USATC AD (2) 11-500 AA-AC (2)
USATC Armor (2)
NG: State AG (3); units - same as Active Army except allowance is one copy to each unit.
USAR: None.
For explanation of abbreviations used, see AR 320-50.
TAGO 6571-A
30
TM 11-5895-227-15
C6
Changes In force: C 3, C 4, C 5, and C 6
}
CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
NO. 6 WASHINGTON, D.C., 20 February 1974
Page 2, paragraph 1.1. Delete paragraph 1.1 and and Handling Deficiencies) as prescribed in AR 700-58
substitute: (Army)/NAVSUP PUB 378 (Navy)AFR 71-4 (Air
Force)/and MCO P4030.29 (Marine Corps), and DSAR
1.1. Indexes of Publications 4145.8.
a. DA Pam 310-4. Refer to the latest issue of DA c. Discrepancy in Shipment Report (DISREP) (SF
Pam 310-4 to determine whether there are new editions, 361). Fill out and forward Discrepancy in Shipment
changes, or additional publications pertaining to the Report (DISREP) (SF 361) as prescribed in AR 55-38
equipment. (Army)/NAVSUPINST 4610.33/AFM 75-18/MCO P4610.19A
b. DA Pam 310-7. Refer to DA Pam 310-7 to (Marine Corps), and DSAR 4500.15.
determine whether there are modification work orders After paragraph 2 add:
(MWO's) pertaining to the equipment.
Paragraph 2. Delete paragraph 2 andsubstitute: 2.1. Reporting of Errors
1
4.1. Items Comprising an Operable Equipment
FSN QTY Nomenclature Usable
on code
5895-021-2088 Operations Center, Communication
AN/MSC-25 consisting of:
5815-553-6061 1 Reperforator-Transmitter, Teletypewriter, TT-76A, B/GGC,
5805-715-6171 1 Switchboard, Telephone, Manual SB-22A/PT
5805-543-0012 7 Telephone Set TA-312/PT
5805-246-8734 2 Terminal, Telegraph TH-5/TG
5805-831-6062 1 Semitrailer, Van, Electrical Equipment V-189/MSC-25,
V-189A/M SC-25 which includes:
NOTE
In the Usable on code column, number 1 refers to
V-189/MSC-25; number 2 refers to V-189/MSC-25.
NOTE
The part number is followed by the applicable 5-digit
Federal supply code for manufacturers (FSCM) identified
in SB 708-42 and used to identify manufacturer, dis-
tributor, or Government agency, etc.
4120-892-1989 1 Air Conditioner: A-18; 98437 1
4120-964-9261 1 Air Conditioner: Thermo-King model 2
7520-753-4807 4 Basket, Wastepaper: RR-B-181, Style A, Design C; 81348 1,2
6135-120-1020 8 Battery, Dry BA-30 1,2
6135-050-0916 4 Battery, Dry BA-44: f/emergency light 1,2
NOTE
Dry batteries shown are used with the equipment but are
not considered part of the equipment. They will not be
preshipped automatically but are to be requisitioned in
quantities necessary for the particular organization in
accordance with SB 11-6.
5920-291-8305 1 Broom, Upright: H-B-51, Class 1, Type C; 81348 1,2
7920-178-8315 1 Brush, Dusting, Bench: Fed Spec H-B-201, Class B 1,2
5995-889-1500 1 Cable Assembly, Power, Electrical CX-7453/U: (100 ft lg) 1,2
5995-823-2486 1 Cable Assembly, Power, Electrical: 25 ft lg; SM-D-350987; 80063 1,2
5995-752-2548 1 Cable Assembly, Power, Electrical CX-7705/U: 15 ft power 1,2
stub
5995-823-2620 2 Cable Assembly, Special Purpose: f/headset; approx 8 ft lg; 1,2
SM-C-382135, 80063
5995-889-0923 1 Cable Assembly, Telephone: Stub for SB-22/PT; SM-C-353715; 80063 1,2
5995-823-2955 8 Cable Assembly, Telephone: Approx 6 ft lg; PJ-047B one end, 1,2
other end stripped and tinned; SM-C-377563-V; 80063
5995-823-2715 1 Cable Assembly and Reel: 26 ft, 250 ft and RC-435/U 1,2
5995-889-0803 2 Cable Assembly, Telephone CX-4760A/U: (15 ft) 1,2
5995-823-3016 1 Cable Assembly, Telephone: 2 cond; approx 6 ft lg; 1,2
PJ-055B one end; SM-D-384145-I; 80063
5995-889-0608 1 Cable Assembly, Telephone: 2 cond; approx 6 ft lg; 1,2
PJ-055R one end; SM-D-384145-II; 80063
5995-823-2619 1 Cable Assembly, Telephone: 2 con; approx 3 ft 5 in. Ig 1,2
excl term; SM-C-377563-3; 80063
5995-823-2618 4 Cable Assembly, Telephone: 2 cond; approx 3 ft 1 in. Ig 1,2
excl term; SM-C-377563-2; 80063
5995-752-2512 8 Cable Assembly, Telephone: 2 cond; approx 2 ft lg; plug 1,2
each end; SM-D-352593-II; 80063
7105-268-8214 2 Chair, Folding: Metal; w/o arms; AA-291a, Type 1, 1,2
Class 1; 81348
2
FSN QTY Nomenclature, part No and mfr code Usable on
code
7110-273-8798 5 Chair, Rotary: AA-295, Class 1, Size 1; 81348 (When 1,2
replacing remove mtg bracket f/use on new chair)
7110-281-4469 1 Chair, Rotary: Drafting stool; AA{-295, Class 2, Size 3; 1,2
81348 (When replacing, remove mtg bracket f/use on new chair)
6645-892-4369 1 Clock, Wall: MIL-1194, type A; 81349 1
6645-752-7902 1 Clock: MIL-3956, M2 AN5743; 81349 2
7210-753-3043 2 Cushion, Chair: SM350214; 80063 1,2
6110-649-8146 1 Distribution Box J-1077A/U 1,2
5120-293-2692 1 Extractor, Electron Tube: ETP-9; 95344 1,2
5120-752-8862 1 Extractor, Electron Tube: ETP-7; 95344 1,2
4140-729-6001 1 Fan, Ventilating Propeller: KS802L; 82877 1
4130-965-1230 1 Filter, Air-Conditioning: 10-12 in w x 40 in. Ig 1-78 in. 2
thk RP EZ KLEEN; 810004; Type M-V; 82866
5120-776-9917 6 Grip, Cable Jaw: EQA6-8P; 95344 12
5120-776-9918 44 Grip, Cable Jaw: EQA2S; 95344 1,2
5965-682-2769 2 Handset-Headset H-144/U; H-144A, B/U 1,2
4520-224-7909 4 Heater, Space, Electric: AAT-15A; 34217 1,2
5830-752-5337 1 Intercommunication Station LS147CAFI 1,2
6230-729-9614 2 Lantern, Electric: 2106-7; 32572 1,2
5410-752-2525 2 Lead, Electrical: Grd strap; SM-B352166; 80063 1,2
6230-615-5384 1 Light, Extension: 25 ft Ig, 506KS25-18-2SJ; 79409 1,2
5935-752-6011 1 Maintenance Kit, Electronic Equipment: f/maint of 1,2
Connector, Plug U-77/U; SC-B484, SC-B8420, SC-B-
68424, SCB68421, SC-B48429, MS-35537-78; 80063
5126-293-0255 1 Pin Straightener, Electronic: Duro Speciality p/n 1,2
D-279SN
7110-551-5259 1 Safe, Filing Cabinet: Fed Spec AA-F358; 82782 1,2
5120-752-9675 2 Screwdriver, Flat Tip: 2143-6; 72368 1,2
7520-162-4178 1 Sharpener, Pencil: Boston type L 1,2
7430-823-7988 1 Typewriter: Portable; noiseless; 11; 93780 1
7430-824-1424 1 Typewriter: Portable; Remington classic model 2
7530-223-7966 1 Paper, Recording, Teletypewriter: UU-P-547C, type 1, 1,2
class 1; 81348
7510-511-6690 1 Ribbon, Printing, Teletypewriter: DDD-R-311D, type 1, 1,2
grade A, Class 1; 81348
5895-856-5178 2 Screen, Operation Board: 104108B7; 05542 1,2
7530-634-6237 4 Tape, Teletypewriter: UU-T-120; 81348 1,2
5805-503-3337 2 Telephone Circuit, Line Jack TA-222/PT 1,2
5805-715-6175 1 Telephone Circuit, Truck Jack TA-326/PT 1,2
The supplies and material listed in this table are required for operation of this equipment and are authorized to be
requisitioned by SB 700-50. The FSN for the applicable unit of issue required can be found in appropriate supply
catalogs. The FSCM is used as an element in item identification to-designate manufacturer or distributor or Government
agency, etc., and is identified in SB 708-42.
3
Item Description Ref no. And FSCM FSC
1 Paper, Recording, Teletypewriter, type 1,
class 1 UU-P-547C; 7530
81.348
2 Ribbon, Printing, Teletypewriter, type 1, grade A, class 1 DDD-R-311D; 7510
81348
3 Tape, Teletypewriter UU-T-120; 7530
81348
Page ;24, paragraph 11. Delete the last sentence of Page 69, appendix II. Delete appendix II and substitute:
paragraph 11.
APPENDIX II
BASIC ISSUE ITEMS LIST (BIIL) AND ITEMS TROOP
INSTALLED OR AUTHORIZED LIST (ITIAL)
Section I. INTRODUCTION
4
Section II. BASIC ISSUE ITEMS LIST
(1) (2) (3) (4) (5) (6) (7)
ILLUSTRATION
QTY
(A) (B) FEDERAL DESCRIPTION UNIT FURN
FIG. ITEM STOCK PART USABLE OF WITH
NO. NO. NUMBER NUMBER FSCM ON CODE MEAS EQUIP
5
By Order of the Secretary of the Army:
CREIGHTON W. ABRAMS
General, United States Army
Official: Chief of Staff
VERNE L. BOWERS
Major General. United States Army
The Adjutant General
Distribution:
Active Army:
USASA (2) Fort Gordon (10)
CNGB (1) Fort Huachuca (10)
ACSC-E (2) Fort Carson (5)
Dir of Trans (1) Ft Richardson (ECOM Ofc)(2)
COE (1) WSMR (1)
TSG (1) Army Dep (2) except
USAARENBD (1) LBAD (14)
USAMB (10) SAAD (30)
AMC (1) TOAD (14)
TRADOC (2) ATAD (10)
ARADCOM (2) USA Dep (2)
ARADCOM Rgn (2) Sig Sec USA Dep (2)
OS Maj Comd (4) Sig Dep (2)
LOGCOMDS (3) Sig FLDMS (1)
MICOM (2) USAERDAW (1)
TECOM (2) MAAG (1)
USACC (4) USARMIS (1)
MDW (1) Units org under fol TOE:
Armies (2) (1 copy each)
Corps (2) 11-16
HISA (ECOM) (18) 1135
Svc Colleges (1) 11-85
USASESS (5) 11-95
USAADS (2) 11-96
USAFAS (2) 11-97
USAARMS (2) 11-98
USAIS (2) 11-117
USAES (2) 11-127
USAINTS (3) 11-158
WRAMC (1) 11302
USACDCEC (10) 11500 AA-AC
ATS (1) 29-134
USAERDAA (1) 29136
Instl (2) except
NG: Three (3) cys to the fol States AG: AL, DE, FL, NY, and SC.
USAR: None
For explanation of abbreviations used, see AR 310-50.
6
Changes in force: C3, C4, CS, C6, C7, and C8
TM 11-5895-227-15
C8
CHANGE
No. 8
} HEADQUARTERS
DEPARTMENT OF THE ARMY
WASHINGTON, DC, 12 May 1982
TM 11-5895-227-15, 24 April 1961, is changed as .....160 watts" - add: "or AN/UGC-74A(V)3 ..........100
follows: watts".
The title is changed as shown above. Paragraph 4, line 24. Under line 24, add:
Page 3, figure 1. In the block marked "TT-4(*)/TG" add "Weight of AN/MSC-25A .......... 13,000 lb".
"or AN/UGC-74A(V)3". Paragraph 4.3 is added after 4.2.
Paragraph 4, line 12. Under "Teletypewriter TT-4(*)/TG
Usable
NSN QTY Nomenclature, part No. and mfr code on code
5895-00-021-2088 Operations Center, Communication AN/MSC-25A, consisting of
5815-00-553-6061 1 Reperforator-Transmitter, Teletypewriter, TT-76A, B/GGC
5805-00-715-6171 1 Switchboard, Telephone, Manual SB-22AIPT
5805-00-543-0012 7 Telephone Set TA-312/PT
5815-01-062-8194 1 Terminal, Communications AN/UGC-74A(V)3
5805-00-246-8734 2 Terminal, Telegraph TH-5/TG
5805-00-831-6062 1 Semitrailer, Van, Electrical Equipment V-189/MSC-25, V-189A/
MSC-25 which includes:
NOTE
In the Usable on code column, number 1
refers to V-189/MSC-25; number 2 refers to V-
189A/MSC-25.
NOTE
The part number is followed by the applicable
5-digit Federal supply code for manufacturers
(FSCM) identified in SB 708-42 and used to
identify manufacturer, distributor, or
Government agency, etc.
1 Air Conditioner: A-18; 98437 1
4120-00-964-9261 1 Air Conditioner: Thermo-King model 2
4 Basket, Wastepaper: RR-B-181, Style A, Design C; 81348 1.2
Change 8 1
TM 11-5895-227-15
Change 8 2
TM 11-5895-227-15
4.3 Items Comprising an Operable Equipment (ANIMSC-25A)-Continued
Quantity
(ea.) Item Fig. No.
1 Semitrailer, Van, Electronic Equipment V-189/MSC-25 ............................................ 7, 8
1 Switchboard, Telephone, Manual SB-22 (*)/PT including: 14
Accessory Kit MX-230/PT, MX-230A/PT, or MX-2915/PT (storage cabinet
No. 1).
2 Terminal, Telegraph TH-5/TG ................................................................................. 14
7 Telephone Set TA-312/PT (3 installed and 4 stored in storage cabinet
NO. 1). 14, 16
1 Terminal, Communications AN/UGC-74A(V)3 ......................................................... 6.1
1 Reperforator-Transmitter, Teletypewriter TT-76(*)/GGC .......................................... 14
Change 8 3
TM 11-5895-227-15
6.1. Components of Semitrailer Van, Electronic Equipment V-189(*)/MSC-25A
Quantity Fig.
(ea.) Item No. Location
1 Air conditioner (V-189/MSC-25) ................................ 21 Fig. 16.
1 Air conditioner (NSN 4120-00-289-1323 ................... Fig. 16.
(V-189A/MSC-25)
1 Axe, 2-ft ................................ ................................ .... Front compartment.
1 Axe, 3-ft ................................ ................................ .... 15
4 Battery BA-44 (for dome lights) ................................ . 14
1 Battery BA-5598/U ................................ ....................
(Backup supply for AN/UGC-74A(V)3.)
1 Broom ................................ ................................ ...... 15
1 Cable Assembly, Telephone CX-4566/G.................... 3 Fig. 18
(250 ft) with Reel RC-435/U
(V-189/MSC-25).
1 Cable Assembly, Telephone CX-4566A/G..................
(250 ft) with Reel RC-435/U
(V-189A/MSC-25).
1 Cable Assembly, Telephone CX-4760/U.................... 2 Storage cabinet No. 1.
(15 ft) (V-189/MSC-25).
1 Cable Assembly, Telephone CX-4760A/U ................. Storage cabinet No. 1.
(15 ft) (V-189A/MSC-25).
1
1 Cable Assembly, special purpose,
SC-D-960025-001 ................................ ................. Fig. 26.1
1
1 Cable Assembly, ac power,
SC-D-960027-000 ................................ ................. Fig. 26.1
1
1 Cable, signal assembly,
SC-D-983141-005 ................................ ................. Fig. 26.1
2 Chair cushion
1 Clock, 3 in ................................ ................................ 16
1 Distribution Box J-1077A/U ................................ ....... 14 Front compartment
1 Drafting stool ................................ ............................ 14
1 Droplight, 25 ft ................................ .......................... 2 Storage cabinet No. 1
4 Electric heater ................................ .......................... 20 Fig. 14, 15
1 Exhaust blower ................................ ......................... 17
3 Fire extinguisher, 5 lb ................................ ............... 14, 15
1 First aid kit ................................ ............................... 15
2 Folding chair ................................ ............................ 18
2 Ground rod................................ ................................ 15
2 Ground strap ................................ ............................ 2 Storage cabinet No. 1
1 Hand brush ................................ ............................... 15
2 Handset-Headset H-144 (*)/U ................................ ... 2 Storage cabinet No. 1
2 Handset-Headset extension cord, 8 ft ........................ 2 Storage cabinet No. 1
2 Hand lantern ................................ ............................. Fig. 15 and front compart-
................................ ................................ ................. ment.
1 Intercommunication Station LS-147(*)/FI .................. 23 Fig. 14.
1 Ladder, 12-ft ................................ ............................. 27 Fig. 7
2 Ladder ................................ ................................ ...... 29 Fig. 8
1 LINE/BATTERY LIGHTING POWER TRANSFER
relay K1 ................................ ................................ 17 Relay box
1 Line cord, 25 ft, with duplex receptacle ..................... 2 Storage cabinet No. 1
2 Message tray ................................ ............................ Storage cabinet No. 1
2 Padlock (including 2 keys) ................................ ........ Storage cabinet No. 1
8 Patch cord, 2-ft ................................ ......................... 4 Fig. 14
1 Pencil sharpener ................................ ....................... 17
1 Pioneer tool kit including ................................ ........... 5 Fig. 7
1 axe
1 hand shovel
1 pick mattock
1 pick mattock handle
Change 8 4
TM 11-5895-227-15
Quantity Fig.
(ea.) Item No. Location
1 Portable typewriter ................................ .................... 18
1 Power cable assembly, 100 ft ................................ ... 17
6 Power cable grip ................................ ....................... 2 Storage cabinet No. 1
1 Power cable stub, 15 ft ................................ ............. 2 Fig. 17
1 Rubber mat ................................ .............................. Storage drawer No. 12
1 Safe w/4 drawers ................................ ...................... 16
44 Signal cable grip ................................ ....................... 2 Storage cabinet No. 1
1 Sledge hammer ................................ ........................ 15
1 Sledge handle, spare ................................ ................ 15
1 SB-22/PT cable stub
4 Swivel chair ................................ ............................... 15
8 Telephone cord, 4 ft................................ ................... 4
1 Tool roll kit, including ................................ ................ 2 Storage cabinet No. 1
1 bag with 10 pockets
1 adjustable wrench, 8 in.
1 Allen wrench set
1 Knife TL-29
1 lineman's pliers
1 long-nosed pliers
1 screwdriver, 2 in.
1 screwdriver, 4 in.
1 screwdriver, 6 in.
1 socket wrench set
1 vise grip pliers, 7 in.
1 Tube pin straightener ................................ ................ 16
1 Tube puller, 7-pin ................................ ..................... 16
1 Tube puller, 9-pin ................................ ..................... 16
4 Wastebaskets ................................ ........................... 14, 15
1 set Running spares consisting of ................................ .... 6
1 electron tube 6AQ5
1 electron tube 6AU6
1 electron tube 6X4W
7 fluorescent lamps, 20 w, 24 in ............................ Fig. 19
12 fluorescent lamp starters FS-2 .......................... Fig. 19
5 fuses, 1-ampere ................................ ................. Storage cabinet No. 1
5 fuses, 5-ampere ................................ ................. Storage cabinet No. 1
3 glowlamps, NE-45
3 incandescent lamps, 60 w
2 incandescent lamps, 24-volt (dome light)
1 incandescent lamp (spare bulb for lantern)
1 neon lamp NE-34
3 transparent overlay rolls ................................ ..... Fig. 18
1 set Technical manuals for major components ................. Manual holder, Fig. 17
1
Part of AN/UGC-74A(V)3. These components will be packed with the AN/UGC-74A(V)3 on turn-in and stored in
storage cabinet No 1. during limited storage.
Page 9. Paragraph 7.1 is added after 7. A pair of jacks has been added to a cable raceway,
designation strips have been changed on the patch
7.1. Difference Between Models panel and signal entrance box, and power and signal
schematic plates are replaced. The AN/UGC-74A(V)3 is
The Operations Center AN/MSC-25A is similar to the not usable with COMSEC equipment as applied in plain
AN/MSC-25 (plain) with the exception that model of the AN/MSC-25. Modification of
Teletypewriter TT-4(*)/TG has been replaced by
Terminal, Communications AN/UGC-74A(V)3 (fig. 6.1).
Change 8 5
TM 11-5895-227-15
signal cable SC-D-983141-005 to adapt it to the 227-40) is not covered by this publication.
TSEC/KW-7 or to switch box assembly (MWO 11-5895- Figure 6.1 is added after Figure 6.
Change 8 6
TM 11-5895-227-15
Change 8 7
TM 11-5895-227-15
Page 17. Paragraph 8g is added after 8f. 74A(V)3. Three cables are provided to be used with
g. Terminal, Communications AN/UGC74A(V9 Terminal, Communications AN/UGC-74A(V)3: cable
(AN/MSC-25A only). The AN/UGC74A(V)3 (TM 11- assembly, special purpose SC-D-960025-001 for
5815-602-12) is mounted on the curbside tabletop (fig. connection to Battery BA-5398/U, cable assembly, ac
14.1). It is used for teletypewriter communication and power SC-D-960027-000, cable signal assembly SC-D-
for data processing, if required. 483141-005 for connecting the output of the AN/UGC-
Page 20. Paragraph 9l(9) is added after 9l(8). 74A(V)3 to the TH-5TG send and receive loop circuits.
(9) Cable assemblies for use with AN/UGC-
Change 8 8
TM 11-5895-227-15
Change 8 9
TM 11-5895-227-15
Page 24. Paragraph 10a is added after 10a. Check the contents of the AN/MSC-25 or AN/MSC-25A
a.1. . When an AN/MSC-25A is received, check it against the packing list If the pacing list is not available,
(para 11), and then perform the tests in paragraph 16.1. use the table of components (para 5 and 6 for the
When a V-189MSC25A is received, perform the AN/SC-25, para 5.1 and 6.1 for the ANSC-25A) to check
procedures in (1) through (7) below the equipment that probably was packed. Examine the
(1) Check the equipment (para 11). equipment for damage and prepare applicable forms
(2) Install and connect the SB-22(*)PT (para (para 2b)
12). Page 26. Paragraph 16.1 is added after 16.
(3) Install and connect the TA-312/PT’s (para
13). 16.1 Installation of Terminal, Communication
(4) Install and connect the TH-5/TG's (para AN/UGC_74A (V3)(AN/MSC-25A only.
14).
(5) Install and connect the TT-76(*)GGC a. Perform the appropriate service upon receipt of
(para 15). equipment procedures (TM 11-5815-602-12)
(6) Install and connect the AN/UGC-74AV)3 b. Bolt the AN/UGC-74(V)3 to teletype table, use
(para 16.1). hardware supplied
(7) Test the equipment after installation (TM c. Position the web strap across top of equipment
11-515-602-12). and secure
NOTE d. Connect ac power cable between AN/UGC-
When Multimeter TS-297/U or an 74A(V)3 receptacle and AN/UGC-74A(V)3 power
equal size meter is issued for use connector in power raceway. Connect signal cable
with the AN/MSC-25A, it can be between the TH-5/TG (AN/UGC-74A(V)3) receptacle on
stored in the TS-297/U stag box (fig raceway to AN/UGC-74A(V)3 signal jack. Connect
14). Install the canopy (para 17) as battery to BAT connectors on AN/UG-74A(V)3 with
required. battery cable.
Page 27. Figure 26.1 is added after 26.
Paragraph 11 is superseded as follows:
11. Check of Equipment received
Change 8 10
TM 11-5895-227-15
Change 8 11
TM 11-5895-227-15
.
Page 42, Paragraph 32b(3) line 2 after "TT-4" add (Red) jacks of the associated TH-5/TG.
"or AN/UGC-74A(V)3. Page 61. Paragraph 61c(3) is added after 61c(2).
Page 47. Paragraph 46.1 is added after 46. (3) The external circuit for the AN/UGC-
46.1. Removal and Replacement of Terminal, 74A(V)3 and its associated TH-5/TG connects to the
Communications ANIUGC-74A(V)3 (AN/MSC- SIGNAL CONN 1 26-pair cable receptacle (pins 13A,
25A only) 13B, 14A, 14B, 15A, and 15B) or to the AN/UGC-
a. Remove the ac power cord connector plug from 74A(V)3 TR and REC binding post pairs (16, 17, 19 and
the power duct receptacle, and the AN/U(CC-74 signal 20) in the signal entrance box. Inside the van, the
connecting plugs from the TH-5/TG. AN/UGC-74A(V)3 circuit connects through signal duct
b. Remove the bolts and washers that secure the wiring to terminals 3 through 6, on the associated TH-
AN/UGC-74(V)3 to the table top. 5/TG, and through the signal cable to the AN/UGC-
c. Replace the AN/UGC-74(V)3 (para 16.1). 74A(V)3.
NOTE Page 63. Paragraph 63. Add the following note
Use the appropriate TH-5/TG below paragraph heading:
ANIUGC-74A(V)3 receptacle on NOTE
raceway (fig. 14.1) for motor power The instructions in this paragraph
and protective ground connections. apply to both the AN/MSC-25 and the
Energize the teletypewriter ac power ANIMSC-25A.
circuit as required.
d. Insert the black plug and red plug of AN/UGC- Page 65. Appendix I is superseded as follows.
74A(V)3 signal cable into the SEND (Black) and REC
Change 8 12
TM 11-5895-227-15
APPENDIX I
REFERENCES
Change 8 13
TM 11-5895-227-15
Change 8 14
TM 11-5895-227-15
APPENDIX III
MAINTENANCE ALLOCATION
Section I. INTRODUCTION
1. General instruments, one of which is a certified standard of
This appendix provides a summary the main tenance known accuracy, to detect and adjust any discrepancy in
operations for the AN/MSC-25 and AN/MSC-25A. It the accuracy of the instrument being compared.
authorizes categories of maintenance for specific g. install The act of emplacing, seating, or fining
maintenance functions on repairable items and into position an item, part, module Component or
components and the tools and equipment required to assembly) in a manner to allow the proper functioning of
perform each function. This appendix may be used as the equipment or system.
an aid in planning maintenance operations. h. Replace. The act of substituting a serviceable
like type part, subassembly, or module (component or
2. Maintenance Function assembly) for an unserviceable counterpart.
Maintenance functions will be limited to and defined as i. Repair. The application of maintenance
follows:
services (inspect, test, service, adjust, align, calibrate,
a. Inspect. To determine the serviceability of an replace) or other maintenance actions Welding,
item by comparing its physical, mechanical and/or Minding, riveting, straightening, facing, remachining, or
electrical characteristics with established standards resurfacing) to restore serviceability to an item by
through emanation. correcting specific damage, fault, malfunction, or failure
b. Test. To verify serviceability and to detect in a part, subassembly, module [component or
incipient failure by measuring the mechanical or assembly), end item, or system.
electrical characteristics of an item and comparing those j. Overhaul. That maintenance effort
characteristics with prescribed standards. (service/action) necessary to restore an item to a
c. Service. Operations required periodically to completely serviceable/operational condition as
keep an item in proper operating condition, i.e., to clean prescribed by maintenance standards (i.e., DMWR) in
[decontaminate), to preserve, to drain, to paint, or to appropriate technical publications. Overhaul is normally
replenish fuel, lubricants, hydraulic fluids, or the highest degree of maintenance performed by the
compressed air supplies. Army. Overhaul does not normally return an item to like
d Adjust. To maintain, within prescribed limits, by new condition.
bringing into proper or exact position' or by setting the k. Rebuild. Consists of those services/actions
operating characteristics to the specified parameters. necessary for the restoration of unserviceable
e. Align To adjust specified variable elements of equipment to a like new condition in accordance with
an item to bring about optimum or desired performance. original manufacturing standards. Rebuild is the highest
f. Calibrate. To determine and cause corrections degree of materiel maintenance applied to Army
to be made or to be adjusted on instruments or test equipment. The rebuild
measuring and diagnostic equipments used in precision
measurement. Consists of comparisons of two
Change 8 15
TM 11-5895-227-15
operation includes the act of returning to zero those age e. Column 5, Tools and Equipment. Column 5
measurements (hours, miles, etc.) considered in specifies by code, those common tool sets (not
classifying Army equipments/components. individual tools) and special tools, test, and support
equipment required to perform the designated function.
3. Column Entries f. Column 6, Remarks. Column 6 contains an
a. Column 1, Group Number. Column 1 lists group alphabetic code which leads to the remark in section IV,
numbers, the purpose of which is to identify Remarks, which is pertinent to the item opposite the
components, assemblies, subassemblies, and modules particular code.
with the next higher assembly.
b. Column 2, Component/Assembly. Column 2 4. Tool and Test Equipment Requirements (Sect. III)
contains the noun names of components, assemblies, a. Tool or Test Equipment Reference Code. The
subassemblies, and modules for which maintenance is numbers in this column coincide with the numbers used
authorized. in the tools and equipment column of the MAC. The
c. Column 3, Maintenance Functions. Column 3 numbers indicate the applicable tool or test equipment
lists the functions to be performed on the item listed in for the maintenance functions.
column 2. When items are listed without maintenance b. Maintenance Category. The codes in this
functions, it is solely for purpose of having the group column indicate the maintenance category allocated the
numbers in the MAC and RPSTL coincide. tool or test equipment.
d. Column 4, Maintenance Category. Column 4 c. Nomenclature. This column lists the noun name
specifies, by the listing of a "work time" figure in the and nomenclature of the tools and test equipment
appropriate subcolumn(s), the lowest level of required to perform the maintenance functions.
maintenance authorized to perform the function listed in d. National/NATO Stock Number. This column
column 3. This figure represents the active time lists the National/NATO stock number of the specific
required to perform that maintenance function at the tool or test equipment.
indicated category of maintenance. If the number or
e. Tool Number. This column lists the
complexity of the tasks within the listed maintenance
manufacturer's part number of the tool followed by the
function vary at different maintenance categories,
Federal Supply Code for manufacturers (5digit) in
appropriate "work time" figures will be shown for each
parentheses.
category. The number of task-hours specified by the
"work time" figure represents the average time required 5. Remarks (Sect. IV)
to restore an item (assembly, subassembly, component,
module, end item or system) to a serviceable condition a. Reference Code. This code refers to the
under typical field operating conditions. This time appropriate item in section II, column 6.
includes preparation time, troubleshooting time, and b. Remarks. This column provides the required
quality assurance/quality control time in addition to the explanatory information necessary to clarify items
time required to perform the specific tasks identified for appearing in section II.
the maintenance functions authorized in the Back of Manual. Figures 14.1 and 14.2 are
maintenance allocation chart. Subcolumns of column 4 added after Figure 14; Figures 18.1 and 18.2 are added
are as follows: after Figure 18; Figure 42.1 is added after Figure 42;
C-Operator/Crew and Figure 43.1 is added after Figure 43.
O-Organizational
F-Direct Support
H-General Support
D-Depot
Change 8 16
TM 11-5895-227-15
SECTION IV. REMARKS
REFERENCE REMARKS
CODE
I REPAIR OF POWER CABLES, CONNECTORS, AND RF CABLES, EMERGENCY REPAIRS OF HOLES AND
MINOR STRUCTURAL DAMAGE (TB 750-240). ALL OTHER REPAIRS WILL BE PERFORMED BY GENERAL
SUPPORT
J FOR MAINTENANCE ALLOCATION, REFER TO TM 11-6110-201-15P.
Change 8 17
TM 11-5895-227-15
SECTION II MAINTENANCE ALLOCATION CHART
FOR
COMMUNICATIONS OPERATIONS CENTER AN/MSC-25 AND AN/MSC-25A
Change 8 18
TM 11-5895-227-15
TOOL OR TEST
EQUIPMENT MAINTENANCE NATIONAL/NATO TOOL
REF CODE CATEGORY NOMENCLATURE STOCK NUMBER NUMBER
Change 8 19
TM 11-5895-227-15
E. C. MEYER
General United States Army
Official.: Chief of Staff
ROBERT M. JOYCE
Brigadier General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-34B, requirements for TMDE/Calibration Maintenance manual.
By Order of the Secretary of the Army:
CARL E. VUONO
General, United States Army
Official: Chief of Staff
WILLIAM J. MEEHAN II
Brigadier General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-51 Unit and DS/GS requirements for AN/MSC-25,A.
Changes in force: C4, C5, C8, and C9
TM 11-5895-227-15
*C9
CHANGE
N0. 9
} HEADQUARTERS
DEPARTMENT OF THE ARMY
Washington, DC, 9 January 1984
TM 11-5895-227-15, 24 April 1961, is changed as Page 2. Paragraphs 1.1, 2, 2.1, 2.2, 2.3 and 2.4
follows: are superseded as follows:
Add the following warnings to the inside front cover:
WARNING 1.1. Consolidated Index of Army Publications and
• Never operate the generator or shelter until it Blank Forms
has been properly grounded. Electrical defects Refer to the latest issue of DA Pam 310-1 to determine
in the load lines or equipment can cause DEATH whether there are new editions, changes or additional
BY ELECTROCUTION when contact is made publications pertaining to the equipment.
with an ungrounded system.
• Adequate ventilation should be provided while 2. Maintenance Forms, Records, and Reports
using TRICHLOROTRIFLUOROETHANE.
Prolonged breathing of vapor should be a. Reports of Maintenance and Unsatisfactory
avoided. The solvent should not be used near Equipment. Department of the Army forms and
heat or open flame: the products of procedures used for equipment maintenance will be
decomposition are toxic and irritating. Since those prescribed by TM 38-750. The Army Maintenance
TRICHLOROTRIFLUOROETHANE dissolves Management System.
natural oils, prolong contact with skin should be b. Report of Packaging and Handling Deficiencies.
avoided. When necessary, use gloves which the Fill out and forward SF 364 (Report of Discrepancy
solvent cannot penetrate. If the solvent is taken (ROD)) as prescribed in AR 735-11-2/ DLAR
internally, consult a physician immediately. 4140.55/NAVMATINST 4355.73A/AFR 400-54/MCO
• Compressed air shall not be used for 4430.3F.
cleaning purposes except where reduced to less c. Discrepancy in Shipment Report (DISREP) (SF
than 29 pounds per square inch (psi) and then only 361). Fill out and forward Discrepancy in Shipment
with effective chip guarding and personnel Report (DISREP) (SF 361) as prescribed in AR 55-
protective equipment. Do not use compressed air 38/NAVSUPINST 4610.33C/ AFR 75-18/MCO
to dry parts when TRICHLOROTRIFLUOROETHANE P4610.19D/DLAR 4500.15.
has been used. Compressed air is dangerous and
can cause serious bodily harm if protective means 2.1. Reporting Errors and Recommending
or methods are not observed to prevent chip or Improvements
particle (of whatever size).from being blown into the You can help improve this manual. If you find any
eyes or unbroken skin of the operator or other mistakes or if you know of a way to improve the
personnel. procedures, please let us know. Mail your letter or DA
Form 2028 (Recommended Changes to Publications
and Blank Forms) direct to: Commander, US Army
Communications-Electronics Command and Fort
Monmouth, ATTN: DRSEL-ME-MP, Fort Monmouth,
New Jersey 07703. In either case a reply will be
furnished direct to you.
*This change supersedes C3, 24 June 1963; C7, 28 December 1981 and TM 11-5895-227-ESC dated 3 May 1976.
1
C9, TM 11-5895-227-15
2
C9, TM 11-5895-227-15
2.2. Reporting Equipment Improvement repacking do equipment for shipment or limited storage
Recommendations (EIR) are covered in chapter 6 and TM 740-90-1.
If your Communications operation center reels
improvement, let us know. Send us an EIR. You, the 2.4 Destruction of Army Electronics Materiel
user, are the only one who can tell us what you don't like Destruction of Army electronics materiel to prevent
about your .equipment Let us know why you don't like enemy use shall be in accordance with TM 750244-2.
the design. Put it on an SF 368 (Quality Deficiency Paragraph 3, add the following.
Report). Mail it to Commander, US Army
Teletypewriter circuits are adaptable to secure
Communication-electronics command and Fort
communication through the TSECIKW-7 equipment
Monmouth, AT[TN: DRSEIL-ME-MP, Fort Monmouth,
(fig. 1.1).
New Jersey 07703. We'll send you a reply.
Page 3. Add figure 11 after figure 1.
2.3. Administrative Storage After paragraph 4, add the following note:
Administrative Storage of equipment issued to and used NOTE
by Army activities will have preventive maintenance Throughout the manual, where
performed in accordance will the PMCS charts before reference is made to Reperforator-
storing. When removing the equipment from Transmitter, Teletypewriter TT-
Administrative storage the PMCS should be performed 76(*)/GGC, the (*) refers to all models
to assured operational readiness Disassembly and except the plain model.
Figure 1.1. Operations center, communications AN/MSC-25 (modified), signal circuits, block diagram.
3
C9, TM 11-5895-227-15
Useable
NSN QTY Nomenclature, part No. & mfr code on code
5815-00-198-4438 1 Teletypewriter TT-4/TG 1, 2
f. Place a piece of masking tape on the W6 cable supply and terminal unit to 60MA.
connected to terminals 6 and 8 (TD SEND) for use as NOTE
identification later. Although the TT-76(*)/GGC will be
g. Fasten the ground lugs and the original cable used in a 20-ma neutral circuit, the
clamps. SIGNAL/ BIAS switch must be set to
h. Connect the cable leads to terminal board TB-2. the 60MA position to provide the
required operational power for the
i. Connect a 27,000-ohm resistor to terminal
TT-523(*)/GGC.
board TB-1 terminals 7-8. (Remove existing lead on
terminal 8, tape the end and tuck it aside; insulate d. Insert the plug from the selector magnet cable
resistor leads.) into the SELECTOR MAGNET socket marked 20MA on
the power supply and terminal unit.
j. Add a label marked CAUTION: Modified in
accordance with paragraph 15.1, TM 11-5895227-15. e. Remove the plug P7 from its associated
receptacle J7, located at the rear of the TT-76(*)/ GGC.
f. Insert male plug P1 at the bottom of the
15.2. Installation of Low Level Signaling Device
TT523(*)/GGC into receptacle J7 of the TT-76(*)/ GGC.
TT-523A/GGC on TT-76(*)/GGC's
g. Connect plug P7 of the TT-76(*)/GGC to female
NOTE receptacle J1 on the rear of the TT-523(*)/ GGC.
TT-76(*)/GGC's must be "A" model or h. Secure the TT-523(*)/GGC ground strap to the
later. The plain model cannot be adjacent ground binding post on the dust cover of the
used. The use of the TT-523A/GGC TT-76(*)/GGC.
may require more frequent
Page 28, paragraph 18c. Add NOTE as follows:
maintenance of transmitter contacts
than normal. The low level keying NOTE
current is of insufficient value to Set switch S1 to the DUMMY BOX
perform the contact cleaning position prior to performing the
obtained when the teletypewriters following tests. Upon completion of
are used for normal (high-level tests, set switch S1 to AUX position.
power) operation. No timetable or
Page 40, paragraph 27h. After "doorbell switch", add:
schedule can be set up for the
TT-523(*)/GGC low level signaling device 60-30 ma.
frequency of cleaning the contacts.
Clean and burnish the transmitter Page 42, paragraph 32b. Add the following paragraph
contacts as required. after 32b(5).
a. On the TT-76(*)/GGC power supply and (6) TSEC/KW-7 communications security set.
terminal unit, disconnect the existing strap across the Operate the ON/OFF switch to OFF. 3ecure equipment
BIAS TEST MA terminals. after operation as prescribed h. TM 11-5895-1048-13.
b. Connect a 56,000-ohm +10 percent, 1-watt Page 43, chapter 4. Insert the following under the title
resistor across the BIAS TEST MA terminals. of chapter 4:
c. Set the SIGNAL/BIAS switch on the power
5
C9, TM 11-5895-227-15
ORGANIZATIONAL PREVENTIVE
6
C9, TM 11-5895-227-15
B - Before
7
C9, TM 11-5895-227-15
M - Monthly Q - Quarterly
8
C9, TM 11-5895-227-15
(4) Operate Switch S1 to the AUX position. are rescinded.
NOTE Page 65, Appendix I. Delete the reference DA Pam
Use plug adapter for connecting the 310-4 and title and substitute:
TSEC/ KW-7 power cord to DA Pam 310-1 Consolidated Index of Army
receptacle No. 6. Publications and Blank Forms.
Page 62, paragraph 62. Make the. following changes:
Subparagraph a(l), line 12. Add a period after"(fig. 13) Appendix I. After the reference "SB 11-6", add the
light". Delete the remainder of the paragraph as well as following reference:
the "note". TB 43-0125 Installation of Communications
Subparagraph a(2). Delete subparagraph a(2) and Electronic Equipment: Hookup
substitute: of Electrical cables to Mobile
(2) Ac power from receptacle J2 is applied Generator Sets on Fielded
through the power duct wiring to MAIN circuit breaker Equipment to meet Electrical
switch CB15 in the POWER DISTRIBUTION PANEL. Safety Standards.
LINE/BATTERY LIGHTING POWER TRANSFER relay Appendix I. After the reference "TM 11-5805246-10",
K1 disconnects the 24V DC van battery supply from add the following reference:
dome lights DS1 through DS3 and arranges the van TM 11-5805-246- Organizational Maintenance
lighting circuit for ac input through circuit breaker 20 Manual: Terminal, Telegraph
switches CB1 and CB2. (Dome lights DS1 through DS3 TH-5/TG.
may be operated after relay K1 operates, by operation Figure 42 (foldout). At the area: "P/O PATCH PANEL,
of the DOME lights switch to DOME TRACT BAT SWITCHBOARD SB-22 LINE OUT" and
(tractor still connected to van)). Circuit breaker switches "SWITCHBOARD SB-22 LINE IN", make the following
CB1 through CB14 (parallel-connected) are connected changes:
in series with CB15. Wiring to the equipment and Change all prefixes "JR1-" to: JR2-.
convenience receptacles is distributed through the Change all prefixes "JR2-" to: JR1-.
power duct from circuit breaker switches CB1 through Figure 42.1 (foldout). Change the title to read "Figure
CB14. Lamps DS4, DS5, and DS54 are connected 42.1 Operations Center AN/MSC-25 (Modified for
across the ac input lines to CB15 ((1) above). Lamps COMSEC) signal schematic-wiring diagram."
DS40 through DS53 are connected across the circuits Figure 43 (foldout). Make the following changes:
controlled by CB1 through CB14, respectively, and light Delete the two wires that connect the coil of relay K1
individually as each circuit breaker is operated to ON. across 115V AC IN lamp DS54, and add two wires to
Page 63, chapter 6. Change the title of chapter 6 from connect the coil of relay K1 across the 115-volt input
"SHIPMENT AND LIMITED STORAGE AND power on the protected side of MAIN circuit breaker
DEMOLITION TO PREVENT ENEMY USE" to CB15. Indicate that the two new wires have the same
"SHIPMENT AND LIMITED STORAGE". color coding and wire size as the deleted wires.
Page 64. Section II title and paragraphs 65 and 66 C9,
TM 11-5895-227-15
9
By Order of the Secretary of the Army:
ROBERT M. JOYCE
Major General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-51A-1, Operator Maintenance requirements for AN/MSC-25.
TM 11-895-227-15
TECHNICAL MANUAL
No. 11-5895227-15 J
} HEADQUARTERS,
DEPARTMENT OF THE ARMY
WASHINGTON 25, D. C., 24 April-19#9
Paragraph Page
CHAPTER 1 INTRODUCTION
Section I. General .................................................................................... . 1,2 2
II. Description and data .................................................................. 3-9 2-18
4. MAINTENANCE INSTRUCTIONS
Section I. Operator's maintenance............................................................. . 33-49 43-48
II. Organizational, field, and depot maintenance ............................ 50-60 48-59
INDEX ........................................................................................................ 74
AGO 5312A
CHAPTER 1
INTRODUCTION
Section I. GENERAL
1. Scope 2. Forms and Records
a. This manual describes Operations Center, a. Unsatisfactory Equipment Reports. Fill out and
Communications AN/MSC-25 (par. 7) and covers its forward DA Form 468 (Unsatisfactory Equipment
installation, operation, theory, and maintenance. It also Report) or DD Form 787-1 (Electronic Failure Report-
includes instructions for installing components not Signal Equipment) to the Commanding Officer, U.S.
provided as a part of Semitrailer, Van, Electronic Army Signal Materiel Support Agency, ATTN: SIGMS-
Equipment V-189/MSC-25 (van). Except for the van MLM, Fort Monmouth, NJ, as prescribed in AR 700-38
and its components, major components of the AN/MSC- (for DA Form 468) or AR 700-39 (for DD Form 787-1).
25 are covered in detail in their respective technical b. Report of Damaged or Improper Shipment. Fill
manuals (app. I). out and forward DD Form 6 (Report of Damaged or
b. Official nomenclature followed by (*) is used to Improper Shipment) as prescribed in AR 700-58.
indicate all models of the equipments covered in this c. Preventive Maintenance Forms. Prepare
manual. Thus, Reperforator Transmitter, Teletypewriter preventive maintenance forms for the major
TT-76 (*) /GGC represents Reperforator-Transmitters, components (par. 5) as specified in their respective
Teletypewriter TT-76/GGC, TT-76A/GGC, and TT- technical manuals (app. I).
76B/GGC; Teletypewriter TT-4 (*) /TG represents
d. Parts List Form. Forward DA Form 2028
Teletypewriters TT-4/TG, TT-4A/ TG and TT-4B/TG;
(Recommended Changes to DA Technical Manual Parts
Intercommunications. Station L.S-147 (*) /FI represents
Lists or Supply Manual 7, 8, or 9) direct to the
Intercommunication Stations LS-147A/FI, LS-147B/FI,
Commanding Officer, U.S. Army Signal Materiel
LS-147C/1FI, and LS-147D/FI; Switchboard, Telephone,
Support Agency, ATTN: SIGMS-MLM, Fort: Monmouth,
Manual SB-22 (*) /PT represents Switchboards,
NJ, with comments on the parts listing in appendix II.
Telephone, Manual SB-22/PT and S]B-22A/PT;
Handset-Headset H-144(*) /U represents Handset- e. Comments on Manual. Forward all other
Headsets H-144/U and H-144A/U. comments concerning this manual direct to the
Commanding Officer, U.S. Army Signal Materiel
Support Agency, ATTN: SIGMS-PA2d, Fort Monmouth,
N.J.
AGO 5812A 2
4. Technical Characteristics
Voltage requirements................................. .. 115 v, 60 cps,
Power consumption (maximum):.................. single-phase,
Semitrailer, Van, Electronic Equip ......... 3-wire.
ment V-189/MSC-25:
Lights ................................ ......... 1,040 watts.
Exhaust blower........................... 150 watts.
Electric heaters .......................... 6,000 watts.
Air conditioner . .......................... 3,000 watts.
Intercommunication Station
LS147(*) /FI ........................... 32 watts.
Major components:
Teletypewriter TT-4(*) /TG ......... 160 watts.
Terminals, Telegraph TH-5/TG ... 120 watts.
Reperforator-Transmitter Tele-.... 150 watts.
typewriter, TT-76 () /GGC ........ -. 150 watts.
Total ................................ ............... 10,652 -Watts.
Communication facilities:
Local telephone circuit
(TA-312/PT) . ................................ . 7 circuits.
Intercommunication circuit
(LS-147 (*) / FI) ............................. 1 circuit.
Teletypewriter ................................ ....... 2 circuits.
Switchboard ................................ ......... 12 circuits.,
Weight of AN/MSC-25................................ .. 13,000 lb.
Outside dimensions of V-189/MSC-25:
Length -. ................................ ............. 318 in.
Width . ................................ ............... 96 in.
Height . -. ................................ ............. 139 in.
Figure 1. Operations Center, Communication
AN/MSC-25, signal circuits, block diagram .
Quantity Fig.
(ea.) Item No. Location
1 Air conditioner- ................................ .............................. 21 Fig. 16
1 Axe, 2-ft. ................................ ................................ ....... 2 Front compartment .
1 Axe, 3-ft ................................. ................................ ........ 15
4 Battery BA-44 (for dome lights)................................ ....... 14
1 Broom . ................................ ................................ .......... 15
Cable Assembly, Telephone CX-566/G (250 ft) with Reel
RC-436/U ................................ ................................ . 3 Fig. 18
1 Cable Assembly, Telephone CX4760/U (15 ft) ............... 2 Storage cabinet No. 1
1 Canopy- ................................ ................................ ......... 26 External storage compart-
ment.
AGO 5812A 3
Quantity Fig.
(ea.) Item No. Location
2 Chair cushion
1 Clock, 3 in. ................................ ............................... 16
1 Distribution Box J-1077A/U ................................ ....... 14 Front compartment
1 Drafting stool ................................ ............................ 14
1 Droplight,.25 ft ................................ .......................... 2 Storage cabinet No. 1
4 Electric heater ................................ .......................... 20 Fig. 14, 15
1 Exhaust blower ................................ ......................... 17
3 Fire extinguisher, 5 lb ................................ ............... 14, 15
1 First aid kit ................................ ............................... 15
2 Folding chair ................................ ............................. 18
2 Ground rod ................................ ............................... 15
2 Ground strap ................................ ............................ 2 Storage cabinet No 1
1 Hand brush ................................ ............................... 15
2 Handset-Headset H-144 () /U ................................ .... Storage cabinet No 1
2 Handset-Headset extension cord, 8 ft ........................ 2 Storage cabinet No 1
2 Hand lantern ................................ ............................. Fig 15 and front compart
ment.
1I Intercommunication Station LS 147() /FI ................... 28 Fig 14
1 Ladder, 12ft ................................ .............................. 27 Fig 7
2 Ladder................................ ................................ ....... 29 Fig 8
1 LINE/BATTERY .LIGHTING POWER TRANSFER
relay K1 ................................ ............................... 17 Relay box
1 Line cord,'25 ft, with duplex receptacle ..................... 2 Storage cabinet No 1
2 Message tray................................ ............................. Storage cabinet No 1
2 Padlock (including 2 keys) ................................ ........ Storage cabinet No 1
8 Patch cord, 2 ft ................................ ......................... 4 Fig 14
1 Pencil sharpener ................................ ....................... 17
1 Pioneer tool kit including................................ ............ 5 Fig 7
1 axe
1 hand shovel
1 pick mattock
1 pick mattock handle,
1 Portable* typewriter ................................ .................. 18
1 Power cable assembly, 100 ft ................................ ... 17
6 Power cable grip................................ ........................ 2 Storage cabinet No 1
1 Power cable stub, 15 ft ................................ ............. 2 Fig 17
1 Rubber mat ................................ ............................... Storage drawer No 12
1 Safe w/4 drawers ................................ ...................... 16
44 Signal cable grip................................ ........................ 2 Storage cabinet No 1
1 Sledge hammer ................................ ........................ 16
1 Sledge handle, spare ................................ ................ 15
1 SB 22/PT cable stub
4 Swivel chair ................................ .............................. 15
8 Telephone cord, 4 ft ................................ .................. 4
1 Tool roll kit, including ................................ ................ 2 Storage cabinet No 1
1 bag with 10 pockets
1 adjustable wrench, 8 in.
1 Allen wrench set
1 Knife TL-29
1 lineman's pliers
1 long-nosed pliers
1 screwdriver, 2 in.
1 screwdriver, 4 in.
1 screwdriver; 6:'in.
1 socket wrench set
1 vise grip pliers, 7 in..
1 Tube pin straightener................................ ................. 16
1 Tube puller, 7 pin................................ ....................... 16
1 Tube puller, 9,pin ................................ ..................... 16
AGO 5312A 4
Quantity Fig.
(ea.) Item No. Location
AGO 5812A 5
Figure 2. Operations Center, Communications AN/MSC-25, tools and accessories.
AGO 5812A 6
Figure 3. Operations Center, Communications
AN/MSC-25, cable assemblies..
AGO 5812A 7
Figure 5. Operations Center, Communications
AN/MSC-25, pioneer kit storage.
AGO 5812A 8
7. Description PANEL (power entrance box). Alternating current (ac)
The components of Operations Center, power for the AN/MSC-25 must be obtained from a local
Communications AN/MSC-25 (para. 5 and 6) are source (para. 22). Figures 9 and 10 are interior views
housed in Semitrailer, Van, Electronic Equipment V- of the AN/MSC-25; the locations of interior components
189/MSC-25 (figs. 7 and 8). External connections to are shown- in figures 14 through 19. The major
the van are made at the SIGNAL ENTRANCE PANEL components of the AN/MSC-25 are described in
(signal entrance box) or the POWER ENTRANCE paragraph 8, and the van components in paragraph 9.
Figure 7. Operations Center, Communications AN/MSC-25, exterior front and roadside view.
AGO 5812A 9
Figure 8. Operations Center, Communications AN/MSC-25 and tractor, exterior rear
and curbside view.
AGO 5812A 10
Figure 9. Operations Center, Communications AN/MSC-25, interior rear view.
AGO 5812A 11
Figure 10. Operations Center, Communications AN/MSC-25, interior front view.
AGO 5812A 12
8. Description of Major Components of rear wall of the van (fig. 8). It contains
AN/MSC-25 receptacles for connecting ac power
a. Semitrailer, Van, Electronic Equipment V- (para. 22) to the van, and a duplex
189/MSC-25 (figs. 7 and 8). The van is the component convenience ac receptacle (115V AC)
of the AN/MSC-25 in which all other components (para. equipped with a spring-loaded watertight
5 and 6) are installed. The van is divided into front and cover. The power entrance box cover is
rear compartments by the front partition wall (figs. 14 equipped with folding side panels (not
and 15); each compartment has its own entrance door. shown) for weather protection and is
A speaking tube is provided for communication between secured with captive screw-type
compartments. The front compartment is used chiefly fasteners.
as a storage area and the air-conditioned rear (4) Signal entrance box. The signal entrance
compartment, as the work area. A safe and file cabinet, box (fig. 12) is mounted in the exterior
equipped with a combination lock, and an air conditioner rear wall of the van (fig. 8). It contains a
are mounted in the front partition wall. A lighted 26-pair cable receptacle and 29 pairs of
vestibule to the rear compartment is formed by a wall binding posts. Binding post pairs No. 1
partition and an accordion blackout door (fig. 18). through 26 are for optional use in
Lighttight vents for the air conditioner and the exhaust connecting signal circuits to the AN/MSC-
blower are on the outside wall. All equipment racks and 25 (para. 23). The SPARE POS 1
mountings, ac power receptacles, and signal wiring binding posts provide a spare signal
required for mounting and operating the AN/MSC-25 circuit to operating position 1 (fig. 15).
components are installed in the van. Storage areas and The ANT (TRANS. and REC.) and FIL
installed. mounting fixtures are provided for running POWER binding posts are provided for
spares and accessory items. The van can be moved by connecting a radio equipment circuit.
a tractor or transported by cargo aircraft and is fully Note
insulated and weatherproofed. Radio equipment is not provided as a
(1) Lighting (fig. 19). Twenty-two fluorescent component of the AN/MSC-25.
lights and 10 incandescent spotlights (5) Power distribution panel (fig. 13). The
provide lighting for the van. Three dome power distribution panel is located on the
lights, which can be powered either from rear wall of the van (fig. 17). A
the tractor battery, or from the 24V DC glowlamp, associated with each power
battery supply (fig. 14) in the van, are distribution circuit breaker switch (1
provided for emergency lighting. through 14), lights when the switch is at
(2) Power and wiring. Watertight receptacles ON.
in the power entrance box ((3) below) are (6) Signal and power entrance panel. The
provided for connecting the van to an ac signal and power entrance panel is
power source. The ac power is routed mounted on the interior rear wall (fig. 17)
through circuit breaker switches in the and is equipped with a removable cover.
power distribution panel ((5) below) to the It provides access to the rear of the power
equipment power duct receptacles (figs. entrance box and the signal entrance box.
14, 15, and 17). Signal connections are
made at the 26-pair cable RECEPTACLE
or to the binding posts in the signal
entrance box ((4) below).
(3) Power entrance box. The power entrance
box (fig. 11) is mounted in-the exterior
AGO 5812A 13
Figure 11. POWER ENTRANCE panel.
AGO 5812A 14
Figure 12. SIGNAL ENTRANCE panel.
TAGO 5812A-May 15
Figure 13. Power distribution panel.
AGO 5812A 16
b. Switchboard, Telephone, Manual SB-22(*) /PT. d. Terminal, Telegraph TH-5/TG. Two TH5/TG's
The SB-22(*)/PT (TM 11-5805-262-12) is mounted in a (TM 11-5805-246-10) are rack mounted on the top shelf
rack above the curbside tabletop (fig. 14). It is local on the curbside wall (fig. 14). The TH-5/TG's are. used
battery switchboard with facilities for switching a with the TT-76 (*)/GGC and the TT-4 (*)/TG,
maximum of 12 telephone and voice-frequency (vf) e. Reperforator-Transmitter, Teletypewriter TT-
teletypewriter circuits. 76(*)/GGC. The TT-(*)/GGC (TM 11-2225) is mounted
c. Telephone Set TA.-312/PT. Three TA-312 /PT's on the curbside tabletop (fig. 14). It is used for tape
(TM 11-2155) are mounted (less carrying cases) : one relay and manual keyboard operation in the AN/MSC-
above the tabletop (fig. 14), one on the side of storage 25.
cabinet No. 1 (figs. 9 and 14), and one on the front, f. Teletypewriter TT-4(*)/TG. The TT-4 (*)/TG
partition wall (fig. 16). Four TA-312/PT's are located in (TM 11-5815-206-12) is mounted on the curbside
storage cabinet No. 1; when required for use, they tabletop (fig. 14). It is used for teletypewriter
should be placed on the roadside tabletop (fig. 15) communication.
adjacent to the PHONE jacks at positions 1 through 4.
The TA-312/PT's are used for local telephone
communication.
AGO 5812A 17
Figure 17. Operations Center, Communications AN/MSC-25, rear wall, elevation
diagram.
9. Description of V-189/MSC-25 Components airstream. Operating controls are on top of the heater;
a. Electric Heaters. (fig. 20). The electric heaters the power cord extends through a hole in the right side
are secured in their mounting bases on the floor of the of the back cover plate.
van (figs. 14 and 15). Each heater contains a 1.5- b. Exhaust Blower. The exhaust blower, mounted
kilowatt heating element and a fan for air circulation. on the rear wall (fig. 17), is equipped with a removable
The fan operates when the heater is turned on, but may cover that muffles the sound when the blower is
also be operated independently. Horizontal louvers on operating. An exhaust blower vent is provided (para.
the front of the heater are adjustable to deflect the 8a).
AGO 5812A 18
c. Clock. An 8-day, luminous-dial, 24-hour flock is k. LINE/BATTERY LIGHTING POWER
mounted on the front wall (fig. 16). A knob on the left- TRANSFER relay. The LINE/BATTERY LIGHTING
hand side is used for winding and setting the clock. POWER TRANSFER relay K1 is contained in the relay
d. Air Conditioner (fig. 21). The air conditioner is box mounted on the rear wall (fig. 17). The relay
mounted on the floor and extends through the front transfers battery lighting power to the dome lights during
partition wall (fig. 16). It can be used for cooling or failure of the ac power supply.
ventilating (para. 29d). An air duct, connected from the l. Cords and Cables.
rear of the air conditioner to a lighttight air conditioner (1) Power cable assembly (fig. 3). The
outlet vent (fig. 8), provides condenser air discharge to power cable assembly is secured on the
the outside of the van. The air duct connected to the rear door (fig. 17). It is a 100-foot, three-
front of the air conditioner (fig. 10) distributes conductor cable, with a watertight power
conditioned air throughout the work area. connector on each end. It is used to
e. Frequency Meter. The frequency meter, located connect the AN/MSC-25 to a power
between the TT-76(*)/GGC and the TT-4 (*) /TG (fig. source (para. 22).
14), measures the frequency of the ac voltage applied to (2) Power cable stub (fig. 2). The power
the teletypewriter equipment. cable stub is secured on the rear door (fig.
f. Handset-Headset H-144(*)/U. Two H144 (*)/U's 17). It is a 15-foot, thre3conductor cable
are stored in storage cabinet No. 1. An H-144 (*)/U is with a watertight power receptacle on one
used with an 8-foot extension cord to allow greater end and red, white, and black prepared
freedom of movement at the display boards while leads on the other end. It is used to
operating a TA-312 /PT (para. 13). connect the AN/MSC-25 to a power
g. Patch Panel (fig. 22). The patch panel is shelf source (para. 22).
mounted above the SB-22 (*)/PT (fig. 14). It consists of (3) Telephone cords (fig. 4). Each telephone
two jack strips and is used for rearranging telephone, cord is a two-conductor cord with a
teletypewriter, and switchboard circuits (para. 30). telephone plug on one end and prepared
h. Display Boards. Tactical, terrain, or leads on the other; they are used to
communications maps can be fastened to the display connect the TA-312/PT's (para. 13) and
boards, and information charted with grease pencil on the LS-147(*)/FI.
transparent panels. (4) Patch cords (fig. 4). The patch cords are
(1) Status boards. The status boards (fig. secured on a hook adjacent to the patch
15) are provided with transparent sliding panel (fig. 14). They are two-conductor
panels over a tackboard surface. cords equipped with a telephone plug at
each end and are used with the patch
i. Distribution Box J-1077A/U. The J-1077A/U
panel.
(fig. 14) contains 26 pairs of binding posts connected in
parallel with two 26-pair cable receptacles and housed in (5) Handset-headset extension cord. Two 8-
a weather-resistant box. The cover of the box can be foot handset-headset extension cords (fig.
locked in the raised position when making wire and 2) are stored in storage cabinet No. 1.
cable connections. The J-1077A/U can be used to The extension cords are used to connect
connect field wire to 26-pair cables or to terminate and the H-144(*)/U's to TA-213 /PT's (para.
provide cross-connection facilities for cable circuits if 13) to allow freedom of movement at the
the patch panel becomes inadequate or inoperative display boards while operating a
(para. 25b). telephone.
j. Intercommunication Station LS-147(*)/FI (fig. (6) SB-22/PT cable stub. The SB-22/PT
23). The LS-147(*)/FI is mounted on the curbside wall cable stub is 3 feet long and is equipped
(fig. 14). It provides two-way, non-private with a 26-pin connector on one end and
communication in a system that consists of other LS- prepared leads on the other. It is used to
147 (*) /FI's or equivalent equipment. connect the SB-22/PT to its receptacle
(para. 12).
AGO 5812A 19
(7) Cable Assembly, Telephone CX-4566 /G
(250 ft.) (fig. 3). The CX-4566/G consists of
a 250-foot, 26-pair cable, equipped with a
26-pair connector on each end, and is
wound on Reel RC-435/U. The CX-4566/G
is secured to the floor of the front
compartment (fig. 18).
(8) Cable Assembly, Telephone CX-4760 /U (15
ft.) (fig. 2). The CX-4760/U (26-pair cable
stub) is stored in a storage cabinet. It is 15
feet long and is equipped with a 26-pair
connector on one end and prepared leads
on the other end. It is used to adapt a 26-
pair cable f6r connection to binding posts
(para. 25b).
AGO 5812A 20
Figure 21. Air conditioner.
AGO 5812A 21
Figure 22. Patch panel.
AGO 5812A 22
Figure 23. Intercommunication Station LS-147(*)/F1.
AGO 5812A 23
CHAPTER 2
INSTALLATION AND PREOPERATIONAL PROCEDURES
AGO 5812A 24
i. Connect the handset-headset to the SB-22 (3) Use a screwdriver to remove the flathead
(*)/PT (TM 11-5805-262-12) and place the handset- screw that secures the holding plate
headset on the hook provided (fig. 14). (inside the mounting bracket).
(4) Remove the TA-312/PT from its carrying
Note
case; store the case.
To operate the SB-22(*)/PT on the
tabletop at position No. 4 (fig. 15) (5) Insert the holding plate into the buzzer
instead of in the mounting rack at recess in the side of the TA-412/PT.
operating position 5, perform the (6) Place the TA-312/PT in the mounting
procedures in a through e, h, and i bracket and replace the flathead screw.
above and use the SB-22(*)/PT b. Connection.
receptacle at operating position 4. (1) Connect the prepared leads of a
Place the SB-22 (*)/PT on the rubber telephone cord to the LINE binding posts
mat provided (stored in storage on the TA-312/PT.
drawer No. 12). Note
13. Installation and Connection of TA-31 2/PT Install two Batteries BA-30 in the
battery compartment and operate the
Note LB-CB-CBS switch to LB.
When the TA-312/PT's are used at the
roadside tabletop locations (fig. 15), (2) Connect the telephone plug into the
they are not installed in mounting appropriate PHONE jack in the signal duct
brackets (a below). Connect each at positions No. 1 through 5 or at the MAP
1 or MAP 2 positions (figs. 14 and 15).
TA312/PT as described in b below.
Note
a. Installation in Mounting Bracket. Use the 8-foot extension cord (para.
(1) Loosen the wingnut on the side of the 9l(5)) to permit greater freedom of
mounting bracket (fig. 24). movement at the display boards by
(2) Rotate the clamping arm to obtain access connecting it between receptacle
to the flathead screw on the side of the connector U-79/U on the TA-312/PT
mounting. Tighten the wingnut. and the connector plug on the H-144
(*)/U.
AGO 5812A 25
14. Installation and Connection of TH-5/TG's c. Place the TH-5/TG in its mounting rack (fig. 14)
a. Remove the TH-5/TG front panel and chassis and tighten the captive screws on the front panel to
assembly from its case (TM 11-5805246-20). secure the TH-5/TG in position.
b. Remove the spare fuses from the cover d. Connect the wires from the signal duct at each
assembly and store them in a storage drawer. Store the mounting position to the TH-5/TG's as listed in the chart
TH-5/TG case. below.
e. Insert the power cord connector plug of the TH- 16. Installation and Connection of TT-4(*)/TG
5/TG associated with the TT-7 (*)/GGC into its power a. Perform the appropriate service upon receipt of
duct receptacle (TH-5 TT-76). equipment procedures (TM 11-5815-206-12).
f. Insert the power cord connector plug of the TH- b. Remove the wingnuts from the underside of the
5/TG associated with the TT-4(*)/TG into its power duct TT-4(*)/TG tabletop position (fig. 14) and remove the
receptacle (TH-5 TT-4). retaining bars.
c. Position the TT-4(*)/TG on the tabletop. Place
15. Installation and Connection of TT-76(*)/GGC. the retaining bars in the packboard lashing hooks on the
a. Remove the wooden shipping base and the dust TT-4(*)/TG and through the holes in the tabletop.
cover from the TT-76(*)/GGC (TM 11-2225). d. Replace and tighten the wingnuts (b above).
b. Place the TT-76 (*) /GGC in position (fig. 14). e. Perform the appropriate preliminary installation
Aline the holes in the TT-76(*)/GGC base with the holes and final installation procedures (TM 11-5815-206-12).
in the tabletop. Secure the TT-76(*)/GGC in place with Note
the nuts and bolts provided; attach the nuts at the Use the appropriate TH-5 TT-4
underside of the tabletop.
receptacle (fig. 14) and adjacent
c. Perform the appropriate preinstallation services ground for motor power and
and preparation for starting procedures (TM 11-2225). protective ground connections (TM
Note 11-5815-206-12). Energize the
Use the appropriate TH-5 TT-76 teletypewriter ac power circuit (para.
receptacle (fig.14) and adjacent 28) as required.
ground for ground and power f. Insert the black teletypewriter connecting cord
connections (TM 11-2225). Energize plug from the TT-4(*)/TG into one of the SEND jacks,
the teletypewriter ac supply circuit and the red into the REC jack of the associated TH-
(para. 28) as required. 5/TG.
d. Replace the dust cover on the TT-76(*)/GGC
and fasten the web strap across the top of the dust 17. Installation of Canopy
cover. A canopy is supplied with the van for use in shading
e. Insert the gray, black, and red teletypewriter the roof of the van from direct sunlight in hot climates,
connecting cord plugs from the TT-76(*)/GGC into the or as warranted by other climatic conditions. Follow the
SEND, SEND, and REC jacks, respectively, of the
associated TH-5/TG.
AGO 5812A 26
procedures in a through j below to install the canopy. bowhook (fig. 25).
a. Remove the tarpaulin and two lashing ropes f. Loop the lashing rope around the curved bow
from the storage compartment (fig. 7) and remove the and through each grommet on the front of the tarpaulin
canopy bows (fig. 25). and tie the other end of the lashing rope to the roadside
b. Install a curved bow at the front and rear of the bowhook.
van roof (fig. 26), and the straight bows, by positioning g. Tie the front tarpaulin center rope to the cleat on
the bow locating pins and securing the bow wingnuts. the front edge of the van roof.
Use the 12-foot ladder (para. 20d). h. Unfold the tarpaulin, working from front to rear,
c. Place the folded tarpaulin on the front of the van and tie the side tarpaulin ropes to the bowhooks.
roof with the edge marked FRONT parallel with the front i. Tie down the rear end of the tarpaulin as in e, f,
edge of the roof. and g above.
d. Unfold the tarpaulin one fold and center the j. Tighten the rear tarpaulin center rope
tarpaulin center rope. sufficiently to pull the tarpaulin securely over the bows.
e. Tie one end of a lashing rope to a curbside
AGO 5812A 27
18. Testing of Equipment After Installation as in (3) above. Continuity of the circuit
a. Preliminary Procedure. should be completed.
(1) Ground the V-189/MSC-25 (para. 21) and (6) Remove the connections to binding post
make power connections (para. 22) before pair No. 1 of the J-1077A/U ((2) above)
using the lights and convenience and connect the TA-312/PT to binding
receptacles. For test purposes, any post pairs No. 2 through 12, in turn.
satisfactory ground may be used in place Perform ringing and talking tests and
of the ground rods. patch panel jack tests at SWITCHBOARD
(2) Energize the van lighting circuits (paras. SB-22 LINE OUT ((3) above) and
28a through e). SWITCHBOARD SB-22 LINE IN ((4)
above), and continuity tests ((5) above)
Note
for each SB-22 (*)/PT line.
Refer to paragraph 27 for information (7) Connect the TA-312/PT to binding post
covering the V-189/MSC-25 controls pairs No. 13 through 25 of the J-1077A/U,
and instruments. in turn.
(3) Connect the CX-4760/U (15 ft.) (para. 24) (8) Connect another TA-312/PT (para. 13b) to
to the 26-pair cable receptacle in the the MAP 1, MAP 2, and PHONE 1
signal entrance box (fig. 12). through 5 jacks (figs. 14 and 15) in turn.
(4) Remove Distribution Box J-1077A/U from (9) Perform talking and ringing tests between
its mounting (fig. 14). the TA-312/PT's. For example, ring and
(5) Connect the prepared leads of the talk between the TA-312/ PT's connected
CX4760/U to the binding posts on the at binding post pair No. 13 ((7) above)
J1077A/U in sequence. For example, and the MAP 1 jack ((8) above).
connect the CX-4760/U pair 1 (A and B, (10) Perform jack performance tests as in (3),
wht-blu, wht-orn-blu) to binding post pair (4), and (5) above at the OUT MAP 1-IN
No. 1 on the J-1077A/U; CX-4760/U pair 2 MAP 1, OUT MAP 2-IN MAP 2, PHONE
(A and B, wht-brn-blu, wht-gy-blu) to LINE OUT 21 (through 25)-PHONE POS
binding post pair No. 2, etc. Refer to A, IN 1 (through 5) jacks.
figure 41 for CX-4760/U pin and wire color
(11) Remove the field wires from the
code identification.
TA312/PT and J-1077A/U.
b. S3B-22(*)/PT and TA-S12/PT Test Procedure.
c. TT-76(*)/GGC, TT-4(*)/TG, and THS5/TG Test
(1) Remove a TA-312/PT from storage Procedure.
cabinet No. 1.
(1) Connect jumper wires between the
(2) Use field wire to connect the TA-312/PT binding post pairs on the J-1077A/U as
to binding post pair No. 1 in the J- indicated in the chart below.
1077A/U and perform talking and ringing
tests over SB-22 (*)/PT line No. 1.
Binding post pair
(3) Insert one end of a patch cord into the connections Color code of CX4760/U
SWITCHBOARD SB-22 LINE OUT jack
From- To- leads being jumpered
No. 1 at the patch panel (fig. 22) during
14 17 Wht-blu-red to wht-brn-brn
the talking test ((2) above). Continuity of
Wht-yel-red to wht-grn-orn
the circuit should be interrupted.
15 16 Wht-red-red to wht-blk-orn
(4) Remove the patch cord from the Wht-gy-red to wht-orn-orn
SWITCHBOARD SB-22 LINE OUT jack
No. 1 ((3) above) and insert it into the
SWITCHBOARD SB-22 LINE IN jack No. (2) Operate circuit, breaker switch No. 3
1 during the talking test ((2) above). (TTY) on the power distribution panel to
Continuity of the circuit should be ON.
interrupted. (3) Operate the TH-5 TT-4 and TH-5 TT-76
(5) Connect the other end of the patch cord switches (fig. 14) to ON.
AGO 5812A 28
(4) Arrange the TT-4(*)/TG (TM 115815-206- on the TT-4(*)/TG.
12), TT-76(*)/GGC (TM 11-2225), and the (7) Operate the TH-5 TT-4 and TH-5 TT-76
TH-5/TG (TM 115805-246-10) for four- switches (fig. 14) to OFF.
wire, full-duplex operation. (8) Operate circuit breaker switch No. 3 (TTY)
(5) Send from the TT-4(*)/TG and observe to OFF.
the receive tape on the TT-76(*)/GGC for (9) Remove the jumper wires ((1) above)
correct copy. from the J-1077A/U.
(6) Send first from the keyboard and then (10) Disconnect and store the CX-4760/U and
from the transmitter-distributor of the TT- the J-1077A/U.
76(*)/GGC and observe for correct copy
AGO 5812A 29
Figure 27. Semitrailer, Van, Electronic Equipment V-189/MSC-25, landing gear and
external storage facilities.
AGO 5812A 30
b. Lowering Van Leveling Jacks. Both leveling on the leveling jack and insert clevis pin C as shown.
jacks (fig. 8) must be lowered to level the van (c below). (4) Remove the leveling jack pads from their
Lower each leveling jack as follows: storage locations (fig. 8) and position a
(1) Remove clevis pins A and B (fig. 28) pad at each leveling jack (fig. 28).
which secure the side support arm and the (5) Remove the lever bars (adjacent to the
leveling jack in the retracted position (not pintle hook, fig. 8). Insert a lever bar into
shown) on the van. Allow the leveling the hole at the base of each leveling jack
jack assembly to swing downward. (fig. 28).
(2) Position the free end of the side support (6) Rotate the lever bar until the leveling jack
arm into the leveling jack bracket (fig. 28) is seated in the leveling jack pad.
and insert clevis pins A and B as shown. Subsequent rotation may be required for
(3) Remove clevis pin C which secures the leveling the van (c below).
forward support arm to the underside of
the van. Position the forward support arm
AGO 5812A 31
Figure 28. Semitrailer, Van, Electronic Equipment V-189/MSC-25, leveling jack arrangement.
AGO 5812A 32
(b) Replace the 12-foot ladder by Note
following (a) above in reverse. Install a personnel ladder at the front
(2) Personnel ladders (figs. 8 and 29). (four-step) and rear (three-step)
(a) Remove the three-step ladder by doors of the van by inserting the
loosening the locking knobs on the eccentric cams (locking handles
personnel ladder brackets and vertical) into the holes provided and
removing the brackets. Remove turning the locking handles to the
the four-step personnel ladder by horizontal position.
loosening and rotating the fasteners (b) Replace the personnel ladders by
on the underside of the van chassis. following (a) above in reverse.
Figure 29. Semitrailer, Van, Electronic Equipment V-18D/MSC-25, personnel ladder storage.
AGO 5812A 33
d. Select a grounding site within 10 feet of the b. Obtaining Power from Adjacent Shelter or Van.
power entrance box and dig a small hole, about 6 inches The total power consumption of the AN/MSC-25 is
deep, at the site. 10,652 watts. Be sure that the output rating of the
e. Remove any paint or grease from the ground power source for the adjacent shelter or van is not
rod. exceeded when the AN/ MSC-25 is connected.
f. Drive the ground rod into the hole until the top (1) Operate the MAIN circuit breaker switch
of the ground rod is approximately 3 inches above on the power distribution panel (fig. 13) of
ground level. the AN/MSC-25 to OFF.
g. Saturate the ground around the rod with water. (2) Remove the cover from the IN POWER
h. Remove a 10-foot ground strap from storage 115V AC receptacle in the power entrance
cabinet No. 1. box (fig. 11) and connect one end of the
power cable.
i. Connect one end of the ground strap to the
ground rod. Connect the other end of the ground strap (3) Remove the cover of the OUT POWER
to the ground rod connecting post in the power entrance 115V AC receptacle in the power entrance
box (fig. 11). box of the adjacent shelter or van and
connect the other end of the power cable.
j. Replace the sledge hammer in its mounting (fig.
c. Using Commercial Power.
15).
(1) Remove power from the commercial or
central power source terminals before
22. Power Connections
making any connections.
Caution
(2) Connect the red and white leads of the
Ground the van (para. 21) before
power cable stub to the neutral bus bar,
connecting power to the AN/MSC-25.
and the black lead to one of the 120volt
Ac power for the AN/MSC-25 may be obtained by bus bars of the power source if the power
connecting to a nearby shelter or van (b below), or from source is a 50- to 60-cps, 120-240-volt,
a central or a commercial power source. single-phase, three-wire distribution
a. Preliminary Procedure. Use the dome lights, as system.
required, until ac power is connected to the AN/MSC-25. (3) Connect the red and white leads of the
Operate the DOME lights switch (fig. 15) to the TRACT power cable stub to the neutral bus bar,
BAT position if the tractor is connected to the van, and and the black lead to the phase-1, phase-
to the INT BAT after the tractor has been disconnected. 2, or phase-3 bus bar if the power source
Operate the DOME lights switch to INT BAT after the is a 50- to 60-cycle-persecond (cps), 120-
lighting circuit is energized (par. 28). 208-yolt, 3-phase, four-wire distribution
(1) Operate all circuit breaker and equipment system.
switches to OFF. (4) Remove the cover from the power cable
(2) Remove the power cable assembly (fig. stub connector. Connect the power cable
17) and power cable stub. stub to one end of the AN/ MSC-25 power
cable.
Note (5) Remove the cover from the IN POWER
Remove only the power cable 115V AC receptacle in the power entrance
assembly if the AN/MSC-25 is to be box (fig. 11) and connect the other end of
connected to a nearby shelter or van the power cable.
for power. (6) Restore power to the commercial or
(3) Unwind the power cable assembly and central power source terminals.
remove the connector covers.
23. Signal Circuit Planning SB-22 LINE binding pairs No. 1 through 12.
a. Switchboards Circuits. Line terminations for the b. Intershelter Communication Circuits. Line
SB-22 (*)/PT may be completed by connecting a 26-pair terminations for the local telephone (TA-312/PT) circuits
cable to the SIG. CONN. 1 receptacle or field wire to may be made to the SIG. CONN 1 receptacle (pins 18
AGO 5812A 34
through 25) or to the PHONE (1 through 5) MAP 1, and (1) Cover removal.
MAP 2 binding posts. Line terminations for (a) With each hand, grasp the knurled
Intercommunication Station LS-147(*)/FI may be made collar on each end of the connector
to the SIG. CONN. 1 receptacle (pin 26) or to the and turn the collars until the open
INTERCOM binding posts. position is reached (A, fig. 30).
c. Teletypewriter Circuits. Line terminations for (b) Disengage the cam on top of the
the teletypewriter circuits may be made to the SIG cover from the slot on the connector
CONN 1 receptacle (pins 13 through 15) or to binding collar. Lift and remove the cover
post pairs No. 13, 14, and 15 for the TT-76(*)/GGC (TT- (B, fig. 30).
76, TD, TR, and REC, respectively) and the SIG CONN
(2) Coupling procedure.
1 receptacle (pins 16 and 17) or to binding post pairs
No. 16 and 17 for the TT-4(*)/TG (TT-4A TR and REC, (a) Position the two 26-pair connectors
respectively). so that the cams drop into the slots
d. Optional Radio Circuit. The ANT TRANS, REC, of the knurled collars and the male
contacts are aligned with the female
and FIL POWER binding posts have been provided for
contacts (C, fig. 30).
connections to radio equipment; radio equipment is not
supplied as a component of the AN/MSC-25. (b) Carefully press the two connectors
e. Spare Circuits. Binding post pairs No. 20 together (D, fig. 30).
(SPARE) and SPARE POS 1 are provided for spare line (c) Lock the two connectors by turning
circuit terminations as required. the knurled collars until the closed
position is reached (E, fig. 30).
24. Connection Procedure for 26-Pair Cables (d) Lock the two connector covers
(figs. 30 and 31) together.
To couple connectors on 26-pair cables (Cable (3) Uncoupling procedure.
Assemblies, Telephone CX-4566/U (250 ft.) and CX- (a) Unlock the 26-pair connectors by
4760/U (15 feet), use the procedure in a below. To turning the knurled collars until the
couple a connector to the receptacle in the signal open position is reached (A, fig. 30).
entrance box (fig. 12), use the procedure inb below. (b) Carefully pull the connectors apart.
a. Coupling 26-Pair Connector. (4) Cover replacement.
Caution (a) Unlock the two connector covers.
Handle the 26-pair connectors (b) Position the cover on top of the 26-
carefully during the coupling and pair connector.
uncoupling procedures. Do not (c) Engage the cam on the top of the
force or twist the connectors during cover in the slot on the connector
installation. Do not drop or place an collar (A, fig. 30).
uncovered 26-pair connector on the (d) Lock the cover to the connector by
ground. turning the collars until the closed
position is reached.
AGO 5812A 35
(e) Turn the knurled collar on the (2) Disconnecting procedure.
connector clockwise until the sleeve (a) Simultaneously turn the receptacle
just engages the cam. collar lever and the connector collar
(f) Simultaneously turn the receptacle until the open position is reached.
collar lever and the connector collar (b) Carefully pull the connectors apart.
until the closed position is reached (c) Replace the covers (a(4) above).
(G, fig. 31).
25. Field Wire Connections (1) Remove the J-1077A/U from the front
a. Connect the field wire pairs to the binding posts compartment (fig. 14) and place it
in the signal entrance box (fig. 12). adjacent to the coupled connectors of the
(1) Loosen the captive screws and lift 26-pair cables.
the cover of the entrance box (fig. (2) Uncouple the 26-pair connectors (para.
8). 24) and connect them to the 26-pair cable
(2) Use the cover support to secure the receptacles on the J-1077A/U.
cover in the open position. (3) Release the fasteners and open the cover
(3) Press down on the binding posts on the J-1077A/U.
(fig. 12) to open the wire slots. (4) Connect the CX-4760/U prepared leads or
Place the field wire pairs in the the field wire pairs to the appropriate
appropriate slots and release the binding posts on the J1077A/U.
binding posts.
Note
b. Use Distribution Box J-1077A/U and connect
Cable Assembly, Telephone CX-4760/U (15 ft.) or field The wire colors of the CX-4760/U are
wire pairs from the signal entrance box into a 26-pair the same as the wire colors of the 26-
cable as follows: pair cable (A, fig. 41).
AGO 5812A 36
CHAPTER 3
OPERATING INSTRUCTIONS
AGO 5812A 37
b. Lighting.
Control, indicator Description and function
BLACKOUT BYPASS-NORMAL switch (fig. 15) Two-position switch. Controls lighting in the AN/MSC-25 for blackout
operation as follows:
Sw pos Permits
BLACKOUT BYPASS.............. Van lighting circuits to be controlled by
the individual light switches.
NORMAL.................................Van lighting circuits to be controlled by
door microswitch.
POWER INDICATOR NEON LAMP (2)............ Neon lamp. Lights when ac power is connected to the AN/MSC-25.
One on rear wall (fig. 17) and one in front compartment.
CURB ODD lights switch.................................. Two-position ON-OFF switch. Controls five fluorescent lights on the
curbside of the ceiling.
CURB EVEN lights switch................................ Two-position ON-OFF switch. Controls four fluorescent lights on
curbside of the ceiling.
ROAD ODD lights switch ................................. Two-position ON-OFF switch. Controls four fluorescent lights on
roadside of the ceiling.
ROAD EVEN lights switch ............................... Two-position ON-OFF switch. Controls four fluorescent lights on
roadside of the ceiling.
SPOTLIGHTS switch ....................................... Two-position ON-OFF switch. Controls application of ac power to all
spotlights. Each spotlight has a built-in ON-OFF switch.
NIGH:TLIGHT switch (fig. 19) ......................... Two-position ON-OFF switch. Controls nightlight.
Front compartment light switch ........................ Two-position ON-OFF switch. Controls three fluorescent lights in the
front compartment.
VESTIBULE lights switch (fig. 17) .................... Two-position ON-OFF switch. Controls fluorescent lights in vestibule.
Door interlock switch........................................ Microswitch. Extinguishes interior van lights when accordion door is
opened (BLACKOUT BYPASS-NORMAL switch in NORMAL
position).
Rear door interlock switch (fig. 17) .................. Microswitch. Extinguishes vestibule lights when rear door is opened.
(BLACKOUT BYPASS-NORMAL switch in NORMAL position.)
Front compartment door interlock switch.......... Microswitch. Extinguishes front compartment lights when front
compartment door is opened. (BLACKOUT BYPASS-NORMAL
switch in NORMAL position.)
DOME lights switch .......................................... Three-position switch. Controls application and selection of de power
source to dome lights.
Sw pos Function
TRACT BAT ........................... Applies dc power from tractor to dome
lights circuit.
OFF ........................................Disconnects dc power from dome lights.
INT BAT .................................Applies dc power from van, 24-V DC
battery supply (fig. 14).
AGO 5812A 38
d. Electric Heater (fig. 20).
Control or indicator Description and function
HEAT-OFF-FAN switch ................................... Three-position toggle switch.
Sw pos Function
HEAT .....................................Applies ac power to heater element and
fan motor.
OFF ........................................Disconnects ac power from heater
element and fan motor.
FAN.........................................Applies ac power to fan only.
TEMPERATURE CONTROL............................ Thermostat control. Regulates the temperature provided by the heating
element.
RESET pushbutton .......................................... Pushbutton which resets the protective circuit breaker within heater.
AGO 5812A 39
g. Signal Duct (figs. 14 and 15).
Jack Description and function
MAP 1 and MAP 2 phone jack boxes .............. One terminating jack in each box. Provide a means of connecting the
TA-312/PT's to external lines.
PHONE jacks at operating positions 1 Terminating jacks. Provide a means of connecting a TA-312/PT
through 5 (5)................................................ from any of the five operating positions to an external line.
INTERCOM jacks at operating positions 1 Parallel-connected terminating jacks. Provide a means of con -
through 5 (5)................................................ necting the LS-147(*)/FI from any of the five operating positions to
an external line.
Binding posts:
FIL PWR (1 red, 1 black) ............................ Binding posts used to connect an external source of filament power to
radio equipment (radio equipment not a component of the AN/MSC-
25).
ANT:
TR (1) ......................................................... Binding posts used to connect transmitting and receiving antenna to
REC (1) radio transmitter and receiver (radio equipment not a component of
the AN/MSC-25).
SPARE: (2) ..................................................... Binding posts used to connect AN/MSC-25 equipment to spare line as
required.
h. Miscellaneous.
Control, indicator, or instrument Description and function
TH-5 TT-4 switch (fig. 14) ................................ Two-position ON-OFF switch. Controls ac power to the TH-5 TT-4
receptacles.
TH-5 TT-76 switch (fig. 14) .............................. Two-position ON-OFF switch. Controls ac power to the TH-5 TT-76
receptacles.
Glowlamps (2) ................................................. Neon lamps adjacent to TH-5 TT-4 and TH-5 TT-76 switches (fig. 14).
Light when the associated switch is ON.
Frequency meter (fig. 14) ................................ Frequency meter with 55- to 65-cps range. Indicates the frequency of
the ac power supplied to the teletypewriter equipment.
BLOWER switch (fig. 17) ................................ Two-position ON-OFF switch. Controls ac power to exhaustblower.
Doorbell switch (fig. 8) ..................................... Pushbutton. Controls ac power to doorbell.
28. Energizing Ac Circuits f. Check to see that the voltmeter (fig. 13)
Warning indicates 115 volts ac ±10 and that the ammeter
To prevent asphyxiation, the indicates nearly 0 ampere. The frequency meter (fig.
AN/MSC-25 must be ventilated at all 14) should indicate 60 cps ±3.
times when occupied. g. Operate circuit breaker switches No. 3 through
Prepare the AN/MSC-25 for full operation as 14 to ON.
follows:
a. Connect the AN/MSC-25 to the available power 29. Operating Procedures
source (para. 22); each POWER INDICATOR NEON Note
LAMP (fig. 17) and the 115V AC IN glowlamp (fig. 13) Operate the TH-5 TT-4 and TH-5 TT-
should light. 76 switches to ON before using the
b. Operate the MAIN circuit breaker switch on the teletypewriter circuits. Refer to the
power distribution panel (fig. 13) to ON. applicable technical manuals (app. I)
c. Operate the BLACKOUT BYPASS-NORMAL for operating procedures of the
switch (fig. 15) to BLACKOUT BYPASS. When major components. Refer to
blackout conditions are required, operate the switch to paragraph 27 for descriptions and
NORMAL. functions of controls and
d. Operate circuit breaker switches No. 1 and 2 instruments of V-189/MSC-25 (van)
(LIGHTS INT. and LIGHTS VEST.) to ON. components.
e. Operate the lights switches (para. 26b) to ON as Warning
required. To prevent asphyxiation, the van
Note must be ventilated at all times when
The DOME lights switch (fig. 15) occupied.
should be operated to the INT BAT a. Electric Heaters (fig. 20). The electric heaters
position while the 40 AN/MSC-25 is in (4) may be moved (para. 41) to any location accessible
use. Operate to OFF when the to a HEATER receptacle (figs. 14, 15, and 17). Insert
AN/MSC-25 is not in use. the power cord connector plug into the appropriate
AGO 5812A 40
HEATER receptacle and operate the HEAT-OFF-FAN second, then from COOLING to OFF
switch to the desired position. for 2 seconds. Repeat until air
Note conditioner compressor starts
If the HEAT-OFF-FAN switch is quietly.
operated to HEAT, set the (2) Cooling. Set the thermostat control for
TEMPERATURE CONTROL to the AGO 5812A the desired temperature and
desired setting. operate the OFF-VENTILATING-
b. Exhaust Blower. Connect the power cord COOLING switch to the COOLING
connector plug into the blower receptacle (fig. 17) and position.
operate the BLOWER switch to ON.
Caution 30. Patching
Open the exhaust blower vent cover (fig. 22)
on the rear of the van (fig. 8) before Patching is not required during normal operation.
operating the blower. Typical patching procedures for circuit rearrangements
are given in a through d below.
c. Intercommunication Station LS-147(*)/FI (fig.
Note
23).
Patching interrupts service on the
(1) Insert the power cord connector plug into circuits being patched.
the INTERCQM power duct receptacle
(fig. 14). a. External Line to Switchboard. Use a patch cord
(para. 91(4)) to connect between either an OUT MAP 1,
(2) Insert the signal cord plug into the
OUT MAP 2, OUT SPARE, or a PHONE LINE OUT (21
INTERCOM signal duct jack below the
through 25) jack on jack strip No. 1 and the appropriate
LS-147(*)/FI.
SWITCHBOARD SB-22 LINE IN (1 through 12) jack on
(3) Operate the OFF-SEND switch to 5 jack strip No. 2.
(approximately midposition). The
b. External Line to Telephone. Use a patch
glowlamp will light.
c. Internal Telephone Circuit to Switchboard. Use
(4) Operate the PRESS TO TALK switch and
a patch cord to connect between either an IN MAP 1, IN
speak into the speaker-microphone on the
MAP 2, or a PHONE POS IN (1 through 5) jack and a
front panel; release the PRESS TO TALK
SWITCHBOARD SB-22 LINE IN (1 through 12) jack on
switch to receive.
jack strip No. 2.
Note d. Conference Circuit Arrangement. To arrange a
The OFF-SEND switch does not have conference circuit, perform the procedures in (1) through
to be operated to receive a call. (3) below.
(5) Operate the RECEIVE control to regulate (1) Use a patch cord to connect between a
the volume of an incoming call. SWITCHBOARD SB-22 LINE OUT (1
Note. The LS-147(*)/FI may be through 12) jack and a PARALLEL MULT
moved to an operating position on the jack on jack strip No. 1.
roadside tabletop (fig. 15) by removing it (2) Use a patch cord to connect between an
from its mounting (para. 43). Insert the OUT MAP 1, OUT MAP 2, or a PHONE
power cord connector plug and the signal LINE OUT (21 through 25) jack and a
cord plug into the appropriate CONVEN- PARALLEL MULT jack on jack strip No. 1.
IENCE receptacle and INTERCOM jack, (3) Use a patch cord to connect between an
respectively. IN MAP 1, IN MAP 2, or a PHONE POS
d. Air Conditioner (fig. 21). IN (1 through 5) jack on jack strip No. 2
Caution and a PARALLEL MULT jack on jack strip
Open the air conditioner intake (fig. No. 1.
7) and outlet (fig. 8) vents before
operating the air conditioner. 31. Operation Under Adverse Climatic Conditions
Operations Center, Communications AN/ MSC-25
(1) Ventilating. Operate the OFF-VENTI-
can be operated in extremely cold or hot climates.
LATING-COOLING switch to the
Install the canopy (para. 17) as required. The van offers
VENTILATING position.
complete protection from the elements for personnel
Caution and equipment; however, when the entrance boxes are
When the temperature outside the exposed to bad weather conditions, the following
van is 50°F. or less, operate the OFF precautions are necessary:
-VENTILATING-COOLING switch
from OFF to COOLING for 1
AGO 5812A 41
a. Cold Climates. Extreme cold causes the cables a. Major Components. Refer to the applicable
and wires to become hard, brittle, and difficult to handle. technical manuals (app. I) for stopping procedures for
Be careful when handling the cables and when major components (para. 5) as required.
connecting them to the AN/MSC-.25 so that kinks and b. V-189/MSC-25 Components.
unnecessary loops will not result in permanent damage. (1) Electric heaters. Operate the TEMPER-
Make sure that the binding posts and cable receptacles ATURE CONTROL to its lowest setting
on the outside of the AN/MSC-25 are kept free of frost, and the HEAT-OFF-FAN switch to OFF.
snow, and ice by replacing the covers on the
(2) Intercommunication Station LS-147(*)/FI.
receptacles and closing the covers on the entrance
Operate the OFF-SEND switch of OFF.
boxes when they are not in use. Lower the folding side
panels when the entrance box covers are open. (3) Teletypewriter ac supply circuit. Operate
Replace a connector cover as soon as the connector is the TH-5 TT-4 and the TH-5 TT-76
disconnected from the equipment; do not drag or place switches (fig. 14) to OFF.
an open connector in the snow. (4) Air conditioner. Operate the OFF-
b. Hot Climates. In hot, dry climates, the VENTILATING-COOLING switch to OFF.
connectors, receptacles, and binding post are subject to Caution
damage from dirt and dust. Lower the folding side Operate the OFF-VENTILATING-
panels when the entrance box covers are open. Close
COOLING switch to OFF before
the covers on the entrance boxes when they are not in
operating circuit breaker switch No. 9
use and replace the covers on the cable connectors. Do
(AIR COND.) to OFF.
not drag or place an open connector on the ground.
c. Warm, Damp Climates. In warm, damp (5) Blower. Operate the BLOWER switch to
climates, the equipment is subject to damage from OFF.
moisture and fungi. Wipe all moisture and fungi : from Note
the exterior of the equipment with a lint-free cloth. After the other van components have
been turned off, allow the exhaust
32. Stopping Procedures blower to remain in operation at least
10 minutes to evacuate all smoke
Note
and fumes before completing the
To turn the power off in an
stopping procedures and closing the
emergency, operate the MAIN circuit
doors of the van.
breaker switch to OFF.
c. Circuit Breaker and Light Switches. Operate all
circuit breaker and light switches to OFF.
AGO 5812A 42
CHAPTER 4
MAINTENANCE INSTRUCTIONS
AGO 5812A 43
36. Weekly Preventive Maintenance c. Lubricate all metal-to-metal moving parts.
a. Clean and tighten the components, racks,
mountings, installations, cables, and connectors.. Caution
More frequent lubrication may be
b. Inspect the components, racks, mountings,
required for items listed above in
installations, and exposed metal surfaces for rust,
excessively hoot, humid, or dusty
corrosion, and moisture.
areas. Do not overlubricate.
c. Inspect the cables and wires for cuts, breaks,
fraying, deteriorations, kinks, and strain. d. Remove the shelter air-conditioner filters and
d. Inspect for looseness of accessible items, such soak them in cleaning compound, benzine, or naphtha.
as component switches, circuit breaker switches, signal Shake loose dirt from the filters, air-dry them, and
and ac cable assemblies, and glowlamps. replace them in their mountings.
e. Clean the air filters, nameplates, meters, and e. Check the fire extinguishers (figs. 14 and 15) for
clock. broken wire seals on the trigger mechanisms. If an
f. Inspect meters and clock for damaged glass and extinguisher has been used, or if there are any signs of
cases. leakage, request that it be recharged by appropriate
personnel.
g. Wind the clock (fig. 16).
h. Inspect the van for support, installation, rust,
38. Equipment Performance Checklist
corrosion, and moisture.
The equipment performance checklist is used to
i. Check the entrance boxes, exhaust blower vent, systematically check the AN/MSC-25. Only first echelon
and air-conditioner intake and outlet vents for cracks, maintenance corrective measures are given in the
leaks, damaged gaskets, dirt, and grease. Corrective measures column. If the corrective
j. Check for normal operation. measures given do not correct the fault, request higher
echelon maintenance. When using the checklist, start
37. Monthly Preventive Maintenance and at the beginning and follow each. step consecutively. If
Lubrication a trouble is suspected in a particular area, start checking
a. Lubricate locks and latches. Use grease at that point and continue the steps sequentially. Refer
(GGA.). to the power schematic-wiring diagram (fig. 43) when
b. Lubricate the hinges on the van door and on the checking the C-189/MSC-25 ac circuits. When a fault or
trouble is located in a major component item, refer to
entrance boxes, exhaust blower vent, and air vent
the applicable technical manual (app. I). First echelon
covers. Use oil (PL special or OE-10).
repair procedures are given in paragraphs 39 through
49.
AGO 5812A 44
Item Action or Normal Corrective
No. Item condition indication measures
EQUIPMENT 2 Shelter Operate as outlined in Component functions; a. Replace fuses or
PERFORMANCE components. paragraph 29. glowlamps associated lamp (para. 40) and
with components light press RESET
as appropriate. As pushbuttons on air
components are conditioner and
operated, current electric heaters, as
indication on power required..
distribution panel
ammeter increases
(approximately 3
amperes for the exhaust
blower and 10 amperes
for each electric heater).
EQUIPMENT b. Perform appropriate
PERFORMANCE repair procedure
(paras. 39 49).
Note. Notify the
appropriate repair
personnel when repair
of the air conditioner is
required.
3 Major Operate major Communication is possible a. Check suspected
components. components, as on all signal circuits major component for
outlined in appropriate connected to the proper connections
technical AN/MSC-25. (paras. 12-16).
manuals(app. I).
Note. The installation b. Check signal
test procedures (para. 18) connections to
may be used as a check AN/MSC-25 (paras.
for normal operation. 23-25).
STOP 4 Major Perform stopping
components. procedures as
indicated in applicable
technical manuals
(app. I).-
STOP 5 Shelter Perform stopping
components procedure as outlined
in paragraph 32.
39. Replacement of Hand Lantern Batteries and (3) Snap the battery case cover shut.
Bulb b. Replacing Bulb.
(fig. 32) (1) Press the button on the bottom of the
The hand lantern requires four Batteries BA-30 reflector case and lift out the reflector.
which are not supplied with the lantern. A spare bulb is
(2) Unscrew the brass cap at the rear of the
stored inside the reflector case.
bulb and remove the bulb and spring.
a. Replacing Batteries.
(3) Remove the spare bulb from inside the
(1) Pull the battery case latch forward and reflector case. Insert the bulb and spring
raise the battery case cover. in the reflector and tighten the brass cap.
(2) Insert four batteries in the case with, the (4) Replace the reflector in the reflector case
center brass caps up. and snap it securely in position.
AGO 5812A 41
Figure 32. Hand lantern, partially disassembled.
40. Removal and Replacement of Lamps, (4) Replace the lamp and lamp shield (a(4)
Fluorescent Lamp Starters, and Fuses through (6) above).
a. Fluorescent Lamp. c. Neon and Incandescent Lamps. Remove a
(1) Pull gently to remove the light shield from defective neon or incandescent lamp by unscrewing it
the fluorescent light fixture. from its socket.
(2) Rotate the lamp in its sockets one-quarter d. Dome Lamps.
turn and remove it from the fixture. (1) Loosen the captive screw to release the
(3) Remove the spare lamp from its storage lamp panel.
brackets (fig. 19). (2) Remove the lens and unscrew the bulb.
(4) Align the lamp with the slots in the fixture (3) Replace the lens and lamp by following
sockets. the procedures in (1) and (2) above in
(5) Press in and rotate the lamp one-quarter reverse.
turn to seat the pins firmly. e. Relay Box Fuse (fig. 17).
(6) Replace the light shield on the fluorescent (1) Twist the fuse cap counterclockwise and
light fixture. remove the fuse and fuse cap.
b. Fluorescent Lamp Starter. (2) Pull the defective fuse from the fuse cap.
(1) Remove the light shield and lamp (a(1) Remove a 5-ampere fuse from storage
and (2) above) to expose the starter. cabinet No. 1.
(2) Press in and twist the starter one-quarter Caution
turn counterclockwise and withdraw it.
Use only a 5-ampere fuse to avoid
(3) Remove the spare starter from its storage
damage to the equipment.
bracket (fig. 19). Insert the new starter,
press in, and turn it clockwise until it (3) Seat the fuse in the fuseholder and twist
seats. the fuse cap clockwise.
AGO 5812A 46
41. Removal and Replacement of Electric Heater 44. Removal and Replacement of SB-22(*)/PT
(fig. 20) a. Turn the tiedown knobs underneath the SB-22
a. Removal. (*) /PT mounting rack (fig. 14) and raise the retaining
(1) Operate the HEATER-OFF-FAN switch to bar.
OFF. b. Disconnect the handset-headset from the SB-22
(2) Remove the power cord connector plug (*) /PT.
from the HEATER receptacle (figs. 14, c. Slide the SB-22 (*)/PT forward and remove it
15, and 17). from the rack mounting.
(3) Loosen the four turnlock fasteners that d. Remove the batteries from the SB-22(*)/ PT
secure the heater to the mounting base. (TM 11-5805-262-12).
(4) Remove the mounting base knob. e. Disconnect the wires from the binding posts on
(5) Slide the heater to the right until it clears the rear of the SB-22(*)/PT.
the flange on the mounting base and lift f. Replace the SB-22(*)/PT by the following
out the heater. appropriate procedures in paragraph 12.
b. Replacement.
(1) Slide the heater onto the mounting base 45. Removal and Replacement of TA-312/PT
so that it engages the flanges. (fig. .24)
(2) Tighten the four turnlock fasteners. a. Remove the telephone leads from the
(3) Replace and tighten the mounting base TA312/PT binding posts.
knob. b. Remove the flathead screw on the side of the
mounting bracket.
42. Removal and Replacement of Exhaust Blower c. Lift the TA-312/PT out of the mounting bracket
Cover and remove the holding plate from the buzzer recess on
a. Operate the BLOWER switch to OFF (fig. 17). the side of the TA-312/PT.
b. Remove the power cord connector plug from its d. Remove the batteries from the TA-312/PT (TM
receptacle. 11-2155).
c. Remove the 10 screws that secure the cover to e. Replace the TA-312/PT by following the
the front wall and lift off the cover. appropriate procedures in paragraph 13.
d. Replace the cover by following the procedures
in a through c above in the reversed order. 46. Removal and Replacement of TT-76(*)/GGC or
TT-4(*)/TG
43. Removal and Replacement of a. Remove the power cord connector plug from the
Intercommunication Station LS-147(*)/FI power duct receptacle and the teletypewriter connecting
a. Remove the power cord connector plug from the cord plugs from the TH-5/TG.
power duct INTERCOM receptacle (fig. 14). b. Remove the teletypewriter dust cover.
b. Release the case mounting clamps by loosening
the captive wingnuts. Note
On the TT-4(*) /TG only, remove the
c. Disconnect the signal cord from the binding
posts on the rear of the LS-147(*)/FI. tele-typewriter connecting cord leads
from the terminals on the terminal
d. Remove the LS-147 (*) /FI from its mounting
and switchbox.
position.
e. Replace the LS-147 (*) /FI by following the
c. Remove the nuts and bolts that secure the
procedures in a through d above in the reversed. order.
teletypewriter to the tabletop.
d. Replace the dust cover.
e. Replace the teletypewriter by following the
appropriate procedures in paragraph 15 for the TT-76 (*)
/GGC or paragraph 16 for the TT4 (*)/TG.
AGO 5812A 47
b. Remove the teletypewriter connecting cord f. Replace the overlay spool by fitting it into place
plugs from the receptacles and the wires from the and pressing in on the right side.
binding posts on the front panel of the TH-5/TG. g. Thread the overlay over the overhead bar and
c. Loosen the captive screws on the: front panel of pull it down to the clamping bar.
the TH-5/TG. h. Tighten the clamping bar.
d. Lift the equipment rack designation plate; pull i. Secure the overlay cover by tightening the
the TH-5/TG forward and lift it from the rack. knurled bolts.
e. Replace the TH-5/TG by following the
appropriate procedures in paragraph 14. 49. Removal and Replacement of Batteries for
Dome Lights
48. Removal and Replacement of Transparent a. Disconnect the wires from the battery terminals
Overlay (fig. 14) in the 24V DC battery box (fig. 14).
a. Loosen the clamping bar by loosening the b. Loosen the retaining bars by turning the locking
thumbscrews. knobs, and remove the batteries from the mounting.
b. Roll up the overlay by turning the rollup knob. c. Position the replacement batteries (Batteries,
c. Loosen the knurled bolts to open the overlay Dry BA-44) in the mounting; replace and secure the
cover. retaining bars.
d. Press in on the right side of the overlay spool d. Reconnect the wires to the replacement
and remove the spool. Remove the overlay from the batteries in a series arrangement.
spool.
e. Tape the replacement overlay to the spool and
wind the overlay on the spool.
AGO 5812A 48
52. Power Distribution Panel Repairs (fig. 33) the ac power cable at the power entrance box (fig. 11).
a. Preliminary Procedures. Operate the MAIN Remove the four screws that secure the power
circuit breaker switch to OFF. (fig. 13) and disconnect distribution panel cover and remove the cover.
Figure 33. Power distribution panel, meter panel and circuit breaker switch removed.
b. Removal and Replacement of Circuit Breaker (4) Disconnect the black wire wound around
Switch. the current transformer from the MAIN
(1) Grasp the defective circuit breaker switch circuit breaker switch and carefully unwind
and pull it straight out from the panel. the wire from the current transformer.
(2) Tag and disconnect the wires connected (5) Wind the black wire around the
to the circuit breaker switch. replacement transformer.
(3) Connect the wires ((2) above) to the
replacement circuit breaker switch and Caution
press it back into the panel. Be sure that the number of turns is
c. Removal and Replacement of Current the same as on the original
Transformer. transformer. Reconnect the black
wire to the MAIN circuit breaker
(1) Remove the four screws that hold the
meter panel to the power distribution switch (fig. 3).
panel. (6) Position the replacement transformer
inside the panel and replace and tighten
(2) Tag and disconnect the current
the bolts.
transformer leads from the ammeter.
(7) Connect the transformer leads to the
(3) Remove the two bolts that secure the
ammeter.
current transformer inside the panel and
remove the current transformer. (8) Replace the meter panel and tighten the
screws.
Note d. Removal and Replacement of Meter.
Count the number of turns of heavy
black wire around the current Note
transformer before performing the The frequency meter (fig. 14)
procedure in (4) below. removal and replacement procedures
are the same as those for power
distribution panel meters outlined in
(1) through (4) below.
AGO 5812A 49
(1) Remove the bolts that hold the meter to heater from its mounting base (par. 41) and remove the
the meter panel and lift out the meter. backplate and bottom plate as follows:
(2) Tag and disconnect the leads from the (1) Remove the four screws that secure the
meter terminals. bottom plate to the heater.
(3) Connect the leads to the replacement (2) Remove the two screws that secure the
meter. backplate to the bottom plate, and
(4) Position the meter in the panel and remove the bottom plate.
tighten the bolts. (3) Loosen the power cord clamp on the
53. Electric Heater and Repairs backplate.
(fig. 34 and 35) (4) Remove the four screws that secure the
a. Preliminary Procedures. Before performing the backplate to the heater and remove the
repair procedures in b through g below, remove the backplate.
AGO 5812A 50
Figure 35. Electric heater, schematic diagram.
AGO 5812A 51
Caution Caution
Do not alter the shape or length of Be extremely careful when removing
the bare copper wire. this lead. Do not alter the length or
(4) Position the circuit breaker and replace shape of the bare copper wire.
and tighten the screws. (3) Tag and remove the wire connections
f. Removal and Replacement of Motor and from the plug-in terminals on the heating
Impeller element.
(1) Remove the four screws that secure the (4) Remove the screws that secure the
motor bracket to the cabinet and lift out heating element to the cabinet. Be
the motor and bracket. careful not to bend the louvers on the
(2) Tag and disconnect the motor leads at the front of the cabinet during the removal
HEAT-OFF-FAN switch and at the taped procedure.
splice in the heating element cable. (5) Position the replacement element and
(3) Remove the three screws that secure the replace and tighten the screws.
motor to the bracket. (6) Connect the wires to the plug-in terminals
(4) Unscrew the metal fastener that secures of the heating element.
the impeller to the motor shaft and (7) Replace the bare wire connected from the
remove the impeller. circuit breaker ((2) above).
(5) Position and secure a replacement motor (8) Position the motor bracket in the cabinet
in the bracket. Slide the impeller onto the and replace and tighten the screws.
motor shaft and tighten the fastener.
(6) Replace the motor bracket in the cabinet 54. Exhaust Blower Repairs
and connect the motor leads ((2) above). (figs. 36 and 37)
g. Removal and Replacement of Heating Element. a. Preliminary Procedures. Before performing the
repair procedures in b through d below, remove the
(1) Remove the' four screws that secure the
exhaust blower cover (par. 42) and remove the power
motor bracket to the cabinet. Remove the
cord connector plug from its receptacle.
motor bracket.
(2) Loosen the bolt that secures the bare
copper wire from the circuit breaker to the
heating element and remove the wire.
AGO 5812A 52
Figure 36. Exhaust blower, front and rear view.
AGO 5812A 53
b. Removal and Replacement of Capacitor. (13) Replace and tighten the bolts that secure
(1) Loosen the capacitor clamp screw. the motor bracket and blade guard to the
(2) Remove the power cord clamp from the blower.
motor bracket. (14) Replace the exhaust blower by reversing
(3) Slide the capacitor out of the clamp. the procedures in (1) and (2) above.
(4) Tag and disconnect the motor leads and (15) Replace the exhaust blower cover (par.
the power cord from the capacitor 42).
terminals.
(5) Connect the motor leads and the power 55. Removal and Replacement of Switches
cord to the replacement capacitor (fig. a. Power Duct Switches.
37). (1) Operate the associated circuit breaker
(6) Slide the capacitor into the clamp and switch to OFF (fig. 13).
tighten the screw. (2) Remove the screws from the brackets at
(7) Replace the power cord clamp. each end of the switch. Remove the two
brackets and the switchplate.
c. Removal and Replacement of Power Cord.
(3) Remove the switch mounting screws and
(1) Remove the capacitor from the clamp
the switch.
(b(2) through (4) above).
(4) Tag and remove the wires from the switch
(2) Tag and disconnect the power cord leads
and connect them to the replacement
from the capacitor and motor leads.
switch (fig. 43).
(3) Connect the new power cord to the
(5) Replace the switch by following the
capacitor and motor leads (fig. 37).
procedures in (1) through (4) above in
(4) Slide the capacitor into the clamp and reversed order.
tighten the screw.
b. Door Microswitch.
(5) Replace the power cord clamp.
(1) Disconnect ac power from the AN/MSC-
d. Removal and Replacement of Motor and 25.
Impeller.
(2) Remove the switch cover plate.
(1) Remove the two screws from the bottom
(3) Tag and remove the wires from the NO
edge of the plate that holds the exhaust
and C terminals of the switch (fig. 43).
blower to the front wall.
(4) Unscrew the ringnut from the door side of
(2) Lift the exhaust blower away from the
the switch, and remove the switch.
wall.
(5) Replace the switch by following the
(3) Remove the four bolts that secure the
procedures in (1) through (4) above in
blade guard and motor brackets to the
reversed order.
blower ring.
(4) Tag and disconnect the motor leads from
56. Removal and Replacement of Fluorescent Light
the capacitor and power cord.
Fixture Components
(5) Remove the power cord clamp.
(6) Remove the. four screws that secure the Note
motor mounting bracket to the motor. The fluorescent light fixtures are
(7) Loosen the two Allen-head setscrews that fabricated as part of the power duct.
secure the impeller to the motor shaft and The radiofrequency filters are sealed
remove the impeller. units; they are not repairable and are
(8) Slide the impeller (setscrews toward the replaced as a complete unit.
motor) onto the shaft of the new motor a. Operate the associated LIGHT switch (par. 27b)
and tighten the setscrews. to OFF; remove the light shield and the fluorescent
(9) Secure the motor bracket to the new lamp (par. 40a).
motor. b. Carefully pry off the associated power duct
(10) Connect the motor leads to the capacitor cover.
and power cord (fig. 37). c. Tag and disconnect the wires from the defective
(11) Replace the power cord clamp. component (fig. 38) and remove the defective
(12) Position the motor bracket and blade component from the power duct.
guard on the blower ring.
AGO 5812A 54
d. Secure the replacement component in the g. Replace the fluorescent lamp and light shield
power duct. (par. 40a).
e. Connect the wires to the replacement
component.
f. Replace the cover on the power duct.
57. Removal and Replacement of Spotlight 58. Removal and Replacement of 26-Pair Cable
a. Operate the SPOTLIGHTS switch (fig. 15) to Receptacle
OFF. a. Removal.
b. Remove the incandescent lamp from the (1) Remove the screws that fasten the cover
spotlight. to the signal and power entrance panel
c. Remove the screws that secure the lamp socket (fig. 17) and remove the cover.
in the spotlight assembly; tag and disconnect the socket (2) Remove the screws that secure the insert
wiring (fig. 43). clips (figs. 39 and 40).
d. Tag and disconnect the wiring to the spotlight (3) Unfasten the cable clip nearest the 26pair
switch (on the spotlight assembly), and remove the cable receptacle mounting (fig. 39).
switch. (4) At the signal entrance box (fig. 12),
e. Remove the screws that secure the spotlight remove the 26-pair cable receptacle
assembly to the power duct. cover.
f. Replace the spotlight by reversing the (5) Lift the receptacle insert (fig. 40) from the
procedures in a through e above. front of the 26-pair cable receptacle
housing.
(6) Tag and unsolder the wires from the
receptacle insert.
AGO 5812A 55
Figure 39. Power and signal entrance panel, cover removed.
AGO 5812A 56
Figure 40. Cable receptacle, 26-pair, partially disassembled.
AGO 5812A 57
Figure 41. Cable connector and receptacle insert, 26-pair, wiring diagram.
AGO 5812A 58
b. Replacement. hole to be patched. Do not touch the
(1) Connect the cable wires to the cleaned area with hands or dirty cloths.
replacement receptacle insert (fig. 41). (2) If the insulation has been gouged out, fill
the hole with clean' noncombustible
Caution material, if possible. Do not use the glass
Be extremely careful when cloth for this purpose.
connecting and soldering wires. (3) Cut out a piece of glass cloth that will
Excessive heat or pressure will extend 2 inches beyond the edges of the
damage the insert. hole to be repaired.
(2) Carefully place the insert in the 26pair
cable receptacle housing (fig. 40). Warning
Resin No. 797 and curing agent No.
Caution 237 are harmful to the skin. Wash
Be careful not to damage the wires thoroughly with water any area of the
when replacing screws or when body that may have come in contact
taking up slack in the 26-paix cable. with the liquid resin or curing agent.
(4) Pour 3 ounces of resin No. 797 for each
59. Removal and Replacement of LINE/ BATTERY square foot of surface area to be covered
LIGHTING POWER TRANSFER Relay K1 into the mixing cup provided. Shake the
can thoroughly before pouring out the
Warning resin. Temperature and climate will
Disconnect the ac power from the determine the quantity of curing agent
AN/MSC-25 and use the land lantern and cold weather promoter to be added to
during replacement or repair the resin. Use the eye dropper and
procedures. prepare the mixture as follows:
a. Remove the screws that secure the relay box (a) For temperatures above 55° F., fill the
cover (fig. 17) and remove the cover. eye dropper to the redline with curing
agent No. 237. Add the curing agent to
b. Tag and disconnect the wires from relay KI (fig.
the resin and mix thoroughly.
43).
(b) For temperatures between 20°and 55°F.,
c. Remove the relay from its mounting.
fill the eye dropper to the redline with
d. Fasten the replacement relay in place. curing agent No. 237. Fill the eye
e. Resolder the wires to the relay. dropper to the halfway mark with cold
f. Replace the cover on the relay box. weather promoter No. 347. Add the cold
weather promoter to the combined curing
60. Maintenance of V-189/MSC-25 agent and resin and mix thoroughly.
a. The maintenance or replacement of the V- (c) For temperatures below 20°F., fill the eye
189/MSC--25 (van) racks, frames, brackets, and dropper to the redline with curing agent
assorted hardware is accomplished by removing and No. 237; add the curing agent to the resin
replacing screws or bolts. When any exterior and mix thoroughly. Fill the eye dropper
component of the van is replaced, be sure the gasket is to the redline with cold weather promoter
adequately sealed to the van to prevent leakage. The No. 347. Add the cold weather promoter
responsibilities for van maintenance are listed in the to the combined curing agent and resin
maintenance allocation chart (app. II). and mix thoroughly.
b. The exterior skin of the van is susceptible to (5) Use the spatula (or the brush in hard-to-
puncturing or gouging. Use Patch Kit, Shelter, Electrical reach areas or when the temperature is
Equipment (Fed. stock No. 5410783-6250) to repair the above 55°F.) and spread a liberal coating
roof or sides of the van as described in the instructions of the prepared mixture over the surface
provided with the patch kit and given below. to be patched. Place the glass cloth ((3)
(1) Use emery cloth, sandpaper, a knife, or above) over the coating and press it
scraper and remove all paint or foreign lightly with the applicator. Spread a
matter within a 3-inch radius around the second liberal
AGO 5812A 59
coating of the mixture over the glass (7) Depending on the temperature and drying
cloth; work from the center of the patch conditions, the patched surface may be
towards the edges. sanded and painted within 4 to 24 hours
(6) Examine the patch to see that the edges after application of the patch. After the
are flat and firmly embedded in the mixture in the cup and on the spatula has
mixture. Be sure the patch is completely hardened, flex the cup and the spatula to
covered by the mixture. Prepare and crack the mixture. Clean the cup and
apply an additional mixture, if necessary. spatula and store them for future use.
Note Discard the used brush; recap and store
To accelerate curing during cold the containers.
weather, heat the patch with warm, Caution
dry air or radiant heat. Do not use an Shelf-life is severely limited by heat;
open flame. recap the containers tightly and store
them in a cool dry place.
AGO 5812A 60
CHAPTER 5
THEORY
AGO 5812A 61
SPARE binding posts (E53 and E54), in the signal E64) on the signal duct at operating position No. 1 (fig.
entrance box. The spare line circuit connects through 15).
signal duct wiring to the SPARE binding posts (E63 and
AGO 5812A 62
CHAPTER 6
AGO 5812A 63
Section II. DEMOLITION OF MATERIEL TO PREVENT ENEMY USE
65. Authority for Demolition c. Burn. Burn cords and technical manuals; use
Demolition of the equipment will be accomplished gasoline, kerosene, oil, flamethrowers, or incendiary
only upon the order of the commander. The destruction grenades.
procedures in paragraph 66 will be used to prevent d. Bend. Bend panels and cabinets.
further use of the equipment.
66. Methods of Destruction Warning
Use any or all of the following methods to destroy the Be extremely careful with explosives
equipment. and incendiary devices. Use these
a. Smash. Smash the controls, tubes, coils, items only when the need is urgent.
relays, switches, capacitors, transformers, and meters;
use sledges, axes, handaxes, pickaxes, hammers, or
crowbars. e. Explode. If explosives are necessary, use
firearms, grenades, or TNT.
b. Cut. Cut all cables and cords and slash the
wiring on the components; use axes, handaxes, or f. Dispose. Bury or scatter the destroyed parts in
machetes. slit trenches or. foxholes, or throw them into streams.
AGO 5812A 64
APPENDIX I
REFERENCES
AGO 5812A 65
Special Tool Lists and TM 11-5805-262-35P Field and Depot Mainte-
Maintenance Alloca- nance Repair Parts
tion Chart for Termi- and Special Tool Lists
nal, Telegraph TH- for Switchboard, Tele-
5/TG. phone, Manual SB-
TM 11-5805-246-20 Organizational Mainte- 22/PT.
nance Manual: Termi- TM 11-5815-206-12 Operation and Organi-
nal, 'Telegraph TH- zational Maintenance:
5/TG. Teletypewriter Set
TM 11-5805-246-35 Field and Depot Mainte- AN/PGC-1 and Tele-
nance Manual, Termi- typewriters TT4A/
nal, Telegraph TH- TG and TT-4B/TG.
5/TG. TM 11-5815-206-12P Operator's and Organi-
TM 11-5805-246-35P Field and Depot Mainte- zational Maintenance
nance Repair Parts Repair Parts and Spe-
and Special Tool cial Tools List: Tele-
Lists: Terminal, Tele- typewriter Set AN/
graph TH-5/TG. PGC-1 including Tele-
TM 11-5805-257-12P Operator's and Organi- typewriters TT4A/
zational Maintenance TG and TT-4B/TG.
Repair Parts and TM 11-5815-206-35 Field and Depot Mainte-
Special Tool Lists and nance: Teletypewriter
Maintenance Alloca- Set AN/PGC-1 and
tion Chart for Gener- Teletypewriters TT-
ators, Ringing, Hand 4A/TG and TT4B/
G-42/PT and G-42A
/PT. TM 11-5815-206-35P Field and Depot Mainte.
TM 5805-257-35P Field and Depot Mainte- nance Repair Parts
nance .Repair Parts and Special Tool Lists:
and Special Tool AN/PGC-1 including
Lists for Generator, Teletypewriters TT-
TM 11-5805-262-12 Operator's and Organi- TM 11-5815-238-12P Operator's and Organi-
zational Maintenance zational Maintenance
Manual, Switch- Repair Parts and Spe-
boards, Telephone, cial Tool Lists and
Manual SB-22/PT Maintenance Alloca-
and SB-22A/PT. tion Chart: Teletype.
TM 11-5805-262-20P Organizational Mainte- writer Sets AN/GGC
nance Repair Parts -3, AN/GGC-3A, and
and Special Tool Reperforator-Trans-
Lists and Mainte- mitters, Teletype-
nance Allocation writer TT-76/GGC,
Chart for Switch- -76A/GGC, and -76B
board, Telephone, /GGC.
Manual SB-22/PT. TM 11-5815-238-35P Field and Depot Mainte-
TM 11-5805-262-35 Field and Depot Mainte- nance Repair Parts.
nance Manual, Switch- and Special Tool Lists:
boards, Telephone, Teletypewriter Sets
Manual SB-22/PT AN/GGC-3, AN/
and SB-22A/PT. GGC-3A, and Reper-
AGO 5812A 66
forator-Transmitters, cial Tool Lists and
Teletypewriter TT- Maintenance Alloca-
76/GGC, -76A/GGC, tion Chart for Hand-
and -76B/GGC. set-Headsets H-81/U
TM 11-5830-221-12 Operator's and Organi- and H-81A/U.
zational Maintenance TM 11-5965-224-12P Operator and Organiza-
Manual: Intercom- tional Maintenance
munication Station Repair Parts and Spe-
LS-147B/FI. cial Tool Lists and
TM 11-5830-221-12P Operator's and Organi- Maintenance Alloca-
zational Maintenance tion Chart: Handsets
Repair Parts and Spe- H-60/PT and H-165
cial Tool Lists: Inter- /U.
communication Sta- TM 11-5965-233-12P Operator and Organiza-
tion LS-147A/FI and tional Maintenance
LS-147B/FI. Repair Parts and Spe-
TM 11-5830-221-35 Field and Depot Mainte- cial Tool Lists and
nance Manual: Inter- Maintenance Alloca-
communication Sta- tion Chart: Headset-
tion LS-147B/FI. Microphones H-91/U
TM 11-5830-221-35P Field and Depot Mainte- and H-91A/U.
nance Repair Parts TM 11-6625-203-12 Operation and Organi-
and Special Tool Lists: zational Maintenance:
Intercommunication Multimeter AN/URM
Station LS-147A/FI -105, including Multi-
and LS-147B/FI. meter ME-77/U.
TM 11-5895-207-36P Field and Depot Mainte- TM 11-6625-203-12P Operator's and Organi-
nance Repair Parts zational Maintenance
and Special Tool Lists Repair Parts and Spe-
for Handset-Headsets cial Tool Lists for
H-81/U and H-81A Multimeter AN/URM
/U. -105.
TM 11-5935-204-15P Operator, Organization- TM 11-6625-203-35 Field and Depot Mainte-
al, Field and Depot nance: Multimeter
Maintenance Repair AN/URM-105 includ-
Parts and Special ing Multimeter ME-
Tool Lists and Mainte- 77/U.
nance Allocation TM 11-6625-203-35P Field and Depot Mainte-
Chart: Connector, nance Repair Parts
Receptacle, Electrical and Special Tool Lists
U-185A/G. for Multimeter AN/
TM 11-5935-205-15P Operator, Organization- URM-105.
al, Field and Depot TM 11-6625-274-10P Operator's Maintenance
Maintenance Repair Repair Parts and Spe-
Parts and Special cial Tool Lists for
Tool Lists and Main- Test Sets, Electron
tenance Allocation Tube TV-7/U, TV-
Chart: Connector, 7A/U, TV-7B/U, and
Receptacle, Electrical TV-7D/U.
U-187/G. TM 11-6625-274-12 Operator's and Organi-
TM 11-5965-207-12P Operator's Organiza- zational Maintenance
tional Maintenance Manual: Test Sets,
Repair Parts and Spe- Electron Tube TV-
AGO 5812A 67
7/U, TV-,7A/U, -TV- and TV-7D/U.
7B/U, and TV-7D/U. TM 11-6625-274-35P Field and Depot Mainte-
TM 11-6625-274-20P Organizational Mainte- nance Repair Parts
nance Repair Parts and Special Tool Lists
and Special Tool Lists for Test Sets, Elec-
for Test Sets, Elec- tron Tube TV-7/U,
tron, Tube TV-7/U, TV-7A/U, TV-7B/U,
TV-7A/U, TV-7B/U, and TV-7D/U.
AGO 5812A 68
APPENDIX II
MAINTENANCE ALLOCATION
Section I. INTRODUCTION
AGO 5812A 69
(2) 1st, 2d, 3d, 4th, 5th echelon. A dagger (±) communication zones to provide theater
symbol indicates the echelons allocated communications, those maintenance functions allocated
the facility. up to and including fourth echelon are authorized to the
(3) Tool code. This column lists the tool code organization operating this equipment.
assigned.
3. Mounting Hardware
(4) Remarks. Entries in this column' are used
The basic entries of this maintenance allocation chart
to clarify data in the other columns.
do not include mounting hardware such as screws, nuts,
bolts, washers, brackets, clamps, etc.
2. Maintenance by Using -Organizations
When this equipment is used by signal service
organizations organic to the theater headquarters or
AGO 5812A 70
SECTION II MAINTENANCE ALLOCATION CHART
st nd rd th th
Maintenance 1 2 3 4 5 Tool
Tools Required For Maintenance Functions Function ech. ech. ech. ech. ech. Code Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9)
AGO 5812A 71
SECTION II MAINTENANCE ALLOCATION CHART
st nd rd th th
Maintenance 1 2 3 4 5 Tool
Tools Required For Maintenance Functions Function ech. ech. ech. ech. ech. Code Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9)
AN/MSC-25
MULTIMETER, AN/URM-105 + 1
MULTIMETER, TS-352/U + + + 2
TOOL KIT, GENERAL MECHANIC + + + + 3
SOLDERING IRON, TL-117 + + + + 4
AGO 5812A 72
Figure 44. Intercommunication Station LS-147D/FI, schematic diagram
AGO 5812A 73
INDEX
Paragraph Page
Ac circuits: Paragraph Page
Connecting........................................ 22 34 Demolition............................................ 65, 66 64
Description........................................ 8a 13 Description:
Energizing......................................... 28 40 Air conditioner................................... 9d 19
Grounding......................................... 21 33 AN/MSC-25....................................... 7 9
Lighting............................................. 8a 13 Cable Assembly Telephone
Stopping ........................................... 32 42 CX4760/U...................................... 9f 19
Theory .............................................. 62 62 Clock ................................................ 9c 19
Troubleshooting................................ 50, 51 48 Cords and cables.............................. 9l 19
Air conditioner: Display board.................................... 9h 19
Controls ............................................ 27e 39 Distribution Box J-1077A/U............... 9i 19
Description........................................ 9d 19 Electric heater................................... 9a 18
Operation.......................................... 29d 41 Exhaust blower ................................. 9b 18
Stopping ........................................... 32 42 Frequency meter............................... 9e 19
Ammeter: Handset-Headset H-144 (*) / U.......... 9f 19
Description........................................ 27a 37 Intercommunication Station
Replacement..................................... 52 49 LS-147(*) /FI 9i 19
Theory .............................................. 62 62 Lighting............................................. 8a 18
Authority for demolition 65 64 LINE/BATTERY LIGHTING
Cables.................................................. 91 19 POWER TRANSFER relay ............ 9k 19
Canopy ................................................ 17 26 Patch panel....................................... 9g 19
Characteristics, AN/MSC-25 technical.. 4 3 Power distribution panel.................... 8a 13
Chart, troubleshooting references......... 51 48 Power entrance box.......................... 8a 13
Checking of equipment received.......... 11 24 Reperforator-Transmitter, Teletype-
Checklist, equipment performance....... 38 44 writer TT-76(*) /GGC 8e 16
Circuit breakers: Semitrailer, Van, Electronic
Operation.......................................... 28 40 Equipment V-189/MSC-25 ............. 8a 13
Replacement..................................... 52 49 Signal and power entrance panel...... 8a 13
Troubleshooting................................ 50, 51 48 Signal entrance box.......................... 8a 13
Circuit planning, signal......................... 23 34 Switchboard, Telephone Manual
Circuits: SB-22 (*)/PT .................................. 8b 16
Ac power........................................... 62 62 Telephone Set TA-312/PT................. 8c 16
Signal ............................................... 61 61 Teletypewriter TT-4 (*) /TG ............... 8f 16
Clock.................................................... 9c 19 Terminal, Telegraph TH-5/TG ........... 8d 16
Cold climates, operation....................... 31 41 Disassembly of equipment................... 63 63
Comments on manual.......................... 2e 2 Display boards ..................................... 9k 19
Components: Disposition of V-189/MSC-25............... 20 29
Connections...................................... 13-16 25, 26 Distribution Box J-1077A/U .................. 9i, 19, 36
Description........................................ 8, 9 13-18 25b
Installation of major components....... 13-16 25, 26 Door microswitch, replacement ............ 55b 54
Installation testing............................. 18 28 Electric heater:
List.................................................... 5, 6 3 Controls ............................................ 27d 39
Power consumption........................... 4 3 Description........................................ 9a 18
Connections: Operation.......................................... 29a 40
Field wire .......................................... 25 86 Repair............................................... 53 50
Major components ............................ 12-16 24-26 Replacement..................................... 41 47
Power ............................................... 22 34 Stopping procedures......................... 32 42
26-pair cable..................................... 24 36 Troubleshooting................................ 50, 51 48
Controls, shelter components............... 27 37 Energizing ac circuits ........................... 28 40
Cords ................................................... 9l 19 Equipment performance checklist ........ 38 44
Current transformer, replacement......... 52c 49 Exhaust blowers:
Daily preventive maintenance .............. 35 43 Control.............................................. 27h 40
Cover removal .................................. 42 47
Description........................................ 9b 18
AGO 5812A 74
Paragraph Page Paragraph Page
Power:
Operation.......................................... 29 40 Cable and reel assembly................ 9l 19
Repair............................................... 54 52 Cable stub ..................................... 9l 19
Stopping ........................................... 32 42 Connections................................... 22 34
Troubleshooting................................ 50, 51 48 Consumption.................................. 4 3
Extension cord for H-144(*)/U .............. 9l 19 Power distribution panel:
Field wire connections.......................... 25 36 Controls and instruments............... 27a 37
Fluorescent fixture repair ..................... 40, 56 46, 54 Description..................................... 8a 13
Forms and records............................... 2 2 Repairs .......................................... 52 49
General maintenance........................... 33 43 Troubleshooting instructions........... 50, 51 48
Grounding............................................ 21 33 Power duct switch, replacement........... 55a 54
Hot climates, operation 31 41 Power entrance box............................. 8a 13
Installation: Purpose and use.................................. 3 2
Canopy.......................................... 17 26 Records and forms............................... 2 2
General.......................................... 10 24 Removal and replacement:
SB-22(*)/PT ................................... 12 24 Batteries for 24 VDC supply........... 49 48
TA-312/PT ..................................... 13 25 Circuit breaker switches................. 52b 49
TH-6/TG ........................................ 14 26 Current transformer........................ 52c 49
TT-4(*)/TG ..................................... 16 26 Dome lamp .................................... 40d 46
TT-76(*)/GGC ................................ -15 26 Electric heater and parts................ 41, 53 47, 50
Installation testing ................................ 18 28 Exhaust blower cover and parts..... 42, 54 47, 52
Intercommunication Station Fluorescent light fixture parts......... 40, 56 46, 54
LS-147(*)/FI ...................................... 9j 19 Fluorescent lamp starter ................ 40 46
Lamps, replacement............................. 40 46 Fuse, relay box .............................. 40 46
Landing gear........................................ 20 29 Intercommunication Station
Lantern, hand, repairs.......................... 39 45 LS-147 (*)/FI 43 47
Leveling AN/MSC-25............................ 20 29 Lamps............................................ 40 46
Lighting: LINE/BATTERY LIGHTING
Controls ......................................... 27b 38 POWER TRANSFER relay ......... 59 59
Description..................................... 8a 13 Meters............................................... 52d 49
Droplight ........................................ 6 3 Personnel ladders............................. 20d 32
LINE/BATTERY LIGHTING POWER Reperforator-Transmitter, Teletype-
TRANSFER relay.............................. 9k, 59 19, 59 writer TT-76(*) /GGC 46 47
Lubrication ........................................... 37 44 Spotlight fixture.................................... 57 55
Maintenance: Switchboard, Telephone, Manual
Daily preventive ............................. 35 43 SB-22(*)/PT 44 47
Equipment performance checklist.. 38 44 Switches ........................................... 55 54
Forms and records......................... 2c 2 Removal and Replacement:
General.......................................... 33 43 Telephone Set TA-312/PT 45 47
Lubrication..................................... 37 44 Teletypewriter Reperforator-
Monthly preventive ........................ 37 44 Transmitter TT-76/GGC ................. 46 47
Running spares.............................. 6 3 Teletypewriter TT-4A/TG ............... 46 47
Tools and materials........................ 34 43 Terminal, Telegraph TH-5/TG ........ 47 47
Troubleshooting instructions........... 50, 51 48 Transparent overlay....................... 48 48
Weekly preventive ......................... 36 44 26-pair receptacle insert................. 58 55
Materials, maintenance ........................ 34b 43 Repair:
Meters, replacement ............................ 52d 49 Electric heater................................ 53 50
Microswitch, replacement..................... 55 54 Exhaust blower .............................. 54 52
Monthly preventive maintenance.......... 37 44 Fluorescent lamp fixtures............... 56 54
Neon lamps, removal and replacement 40 46 Hand lantern.................................. 40 46
Operation: LINE/BATTERY LIGHTING
Energizing ac circuits..................... 28 40 POWER TRANSFER relay ......... 59 60
Patching ........................................ 30 41 Power distribution panel.................... 52 49
Procedures .................................... 29 40 Semitrailer, Van, Electronic
Stopping ........................................ 32 42 Equipment V-189/MSC-25 ............. 60 60
Under adverse climatic conditions.. 31 41 Spotlight ........................................... 57 55
Patch panel.......................................... 9g, 27f 19, 39 Switches ........................................... 55 64
26-pair receptacle............................. 58 55
Reperforator-Transmitter, Teletype-
writer TT-76 (*) / GGC:
Description ................................. 8e 16
AGO 5812A 75
Paragraph Page Paragraph Page
AGO 5812A 76
BY ORDER OF THE SECRETARY OF THE ARMY:
G. H. DECKER,
General, United States Army,
Official: Chief of Staff.
R. V. LEE,
Major General, United States Army,
The Adjutant General.
Distribution:
Active Army: To be distributed in accordance with DA Form 12-7 requirements for TM 11-series (unclas); plus the
following:
USASA (8) 11-16
Def Atomic Spt Agey (5) 11-67
CNGB (1) 11-95
Tech Stf, DA (1) except 11-96
CSigO (18) 11-97
ARADCOM (2) 11-117
ARADCOM Rgn (2) 11-155
MDW (1) 11-500 (AA-AE.) (4)
Seventh US Army (2) 11-557
EUSA (2) 11-587
Units org under fol TOE: (2 copies 11-592
each except as indicated) 11-597
11-7
NG: State AG (8); units-same as Active Army except allowance is one copy to each unit.
USAR: None.
For explanation of abbreviations used, see AR 320-50.
AGO 5812A 77
TM 11-5895-227-15
Figure FO 43.2. Operation Center Communications. AN/MSC-25 (Modified) Power Schematic Diagram
Change 10
TM 11-5895-227-15
Figure FO 43.3. Operation Center Communications. AN/MSC-25A (Modified), Power Schematic Diagram
Change 10
TM 11-5895-227-15
Figure 14.1. Operations Center, Communications AN/MSC-25A, Curbside Wall Elevation Diagram.
TM 11-5895-227-15
Figure 14.2. Operations Center, Communications AN/MSC-25, Curbside Wall, Elevation Diagram,
(with secure equipment installed).
TM 11-5895-227-15
Figure 18.2. Operations Center, Communications AN/MSC-25, Floor Plan (secure equipment added).
TM 11-5895-227-15
Figure 42.1. Operations Center, Communications AN/MSC-25A, Signal Schematic Wiring Diagram.
TM 11-5895-227-15
Temperature (Exact)