Luckylight: 0.56" Triple Digit Numeric Displays Technical Data Sheet
Luckylight: 0.56" Triple Digit Numeric Displays Technical Data Sheet
Date: Nov/23/2009
Drawn: Sun
Page: 1 OF 6
http://www.luckylightled.com
Luckylight
Features:
Descriptions:
The KW3-562XXX series is a lager 14.20mm (0.56) high seven segments display
designed for viewing distances up to 7 meters.
These devices are made with White Diffused segments and gray surface.
Applications:
Audio equipment.
Instrument panels.
Chip Material
GaAlAs
Source Color
Description
Common Cathode
Common Anode
Date: Nov/23/2009
Drawn: Sun
Page: 2 OF 6
http://www.luckylightled.com
Luckylight
Package Dimension:
PIN 28
+
+
PIN 1
DIG.1
DIG.2
DIG.3
A
F
G
E
C
DP
KW3-562CSA
3,26
(COM)
19
(COM)
DIG.1
25 24 4
KW3-562ASA
G DP
18
(COM)
3,26
(COM)
DIG.2
1 27 28 5
21 20 8
G DP
19
(COM)
DIG.3
G DP
6 23 22 9 16 15 13 11 10 17 12 14
DIG.2
DIG.1
25 24 4
G DP
1 27 28 5
18
(COM)
21 20 8
G DP
DIG.3
G DP
6 23 22 9 16 15 13 11 10 17 12 14
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is 0.25 mm (.010) unless otherwise noted.
3. Specifications are subject to change without notice.
Date: Nov/23/2009
Drawn: Sun
Page: 3 OF 6
http://www.luckylightled.com
Luckylight
Absolute Maximum Ratings at Ta=25
Parameters
Symbol
Max.
Unit
PD
60
mW
IFP
100
mA
IF
25
mA
0.4
mA/
VR
Topr
-40 to +80
Tstg
-40 to +85
Soldering Temperature
Tsld
Luminous Intensity
mcd
Test Condition
Iv
2.0
4.0
---
IF=20mA (Note 1)
Iv-m
---
---
2:1
---
660
---
nm
IF=20mA
Dominant Wavelength
---
640
---
nm
IF=20mA (Note 2)
---
20
---
nm
IF=20mA
Forward Voltage
VF
---
1.80
2.40
IF=20mA
Reverse Current
IR
---
---
50
VR=5V
IF=10mA
Notes:
1. Luminous intensity is measured with a light sensor and filter combination that
approximates the CIE eye-response curve.
2. The dominant wavelength (d) is derived from the CIE chromaticity diagram and
represents the single wavelength which defines the color of the device.
Date: Nov/23/2009
Drawn: Sun
Page: 4 OF 6
http://www.luckylightled.com
Luckylight
Typical Electrical / Optical Characteristics Curves
(25 Ambient Temperature Unless Otherwise Noted)
Spectrum Distribution
Relative Luminous Intensity (%)
Ta=25
100
75
50
25
0
500
Ta=25
50
20
10
0
30
3.4
100
10
1
-60 -40 -20 0 20 40 60 80 100
Ambient Temperature Ta ()
40
30
25
20
10
0
20
40
60
80 100
Ambient Temperature Ta ()
50
40
750
Ta=25
1000
f=1KHz
Duty=1/10
100
10
1 0
10
10
10
10
Forward Current IF (mA)
Date: Nov/23/2009
Drawn: Sun
Page: 5 OF 6
http://www.luckylightled.com
Luckylight
Please read the following notes before using the datasheets:
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will
cause big current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less.
3. Soldering Condition
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260 for 5 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the
damage of the product is often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used. It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
Date: Nov/23/2009
Drawn: Sun
Page: 6 OF 6
http://www.luckylightled.com