Professional Documents
Culture Documents
La 76070 Sanyo TV Color Television
La 76070 Sanyo TV Color Television
Monolithic Linear IC
LA76070
NTSC Color Television IC
Overview
Package Dimensions
unit: mm
3128-DIP52S
[LA76070]
0.25
13.8
27
15.24
52
26
4.25
0.48
1.05
1.78
0.75
0.51min
3.8
5.1max
46.0
Functions
SANYO: DIP52S
Specifications
Maximum Ratings at Ta = 25C
Parameter
Symbol
Conditions
Rating
Unit
V4 max
9.6
V26 max
9.6
I21 max
25
mA
Ta 65C*
Pd max
1.3
Operating temperature
Topr
10 to +65
Storage temperature
Tstg
55 to +150
Rating
Units
Note: *Provided on a printed circuit board: 83.2 86.0 1.6 mm, material: Bakelite
Symbol
Conditions
V4
7.6
V26
7.6
V
V
I21
19
mA
V4 op
7.3 to 7.9
V26 op
7.3 to 7.9
V
V
121 op
16 to 25
mA
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircrafts
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
LA76070
Electrical Characteristics at Ta = 25C, VCC = V4 = V26 = 7.6 V, ICC = I21 = 19 mA
Parameter
Symbol
Conditions
Ratings
min
typ
max
Unit
HVCC
I4 (IFICC)
IF AGC: 5 V
I26 (YCVICC)
7.2
7.6
8.0
38
46
54
mA
79.5
93.5
107.5
mA
Vdc
[VIF Block]
AFT output voltage with no signal
VAFTn
2.8
3.8
4.8
VOn
4.7
4.9
5.1
fPU
1.0
fPL
1.0
VRFH
CW = 91 dB, DAC = 0
7.7
8.2
9.0
VRFL
CW = 91 dB, DAC = 63
0.2
0.4
RFAGC0
DAC = 0
RFAGC63
DAC = 63
Vdc
MHz
MHz
96
Vdc
Vdc
dB
86
dB
VAFTH
6.2
6.5
7.6
Vdc
VAFTL
0.5
0.9
1.2
Vdc
VAFTS
33
25
17
mV/kHz
VO
1.8
2.0
2.2
Vp-p
VOtip
2.4
2.6
2.8
Vdc
43
46
dB
Vi
Output at 3 dB
V/S
2.5
3.0
Differential gain
DG
2.4
10
Differential phase
DP
10
deg
S/N
CW = 93 dB
I920
55
58
dB
50
dB
AUXG
5.5
6.0
6.5
dB
AUXS
0.2
0.0
+0.2
Vdc
AUXC
INTO
0.1
0.0
+0.1
Vp-p
464
474
484
mVrms
50
dB
100 k
Hz
0.5
60
dB
[SIF Block]
FM detector output voltage
FM limiting sensitivity
FM detector output bandwidth
SOADJ
SLS
Output at 3 dB
SF
Output at 3 dB
STHD
FM = 25 kHz
AM rejection ratio
SAMR
AM = 30 %
SSN
50
40
dB
60
dB
[Audio Block]
Maximum gain
Adjustment range
Frequency characteristics
Muting
Total harmonic distortion
Signal-to-noise ratio
AGMAX
1 kHz
ARANGE
2.5
0.0
60
67
AF
20 kHz
3.0
AMUTE
20 kHz
75
ATHD
ASN
+2.5
dB
dB
+3.0
dB
dB
0.5
DIN.Audio
65
75
dB
dB
[Chroma Block]
ACC amplitude characteristics 1
ACCM1
0.8
1.0
1.2
times
ACCM2
Input: 14 dB/0 dB
0.7
1.0
1.1
times
CLRBY
100
125
140
CLRMN
Color MAX/NOM
1.6
1.8
2.1
times
CLRMM
Color MAX/MIN
33
40
50
dB
No. 5844-2/27
LA76070
Continued from preceding page.
Parameter
Symbol
Conditions
Ratings
min
typ
1
Unit
max
CLRSE
Tint center
TINCEN
TINT NOM
15
%/bit
TINMAX
TINT MAX
30
deg
45
60
TINMIN
TINT MIN
60
deg
45
30
TINSE
0.7
deg
2.0
deg/bit
RB
0.75
0.85
0.95
GB
0.28
0.33
0.38
ANGBR
92
99
107
deg
ANGGB
227
237
247
deg
42
37
30
dB
+350
Hz
350
Hz
KILL
CVCOF
PULIN+
PULIN
0 dB = 40 IRE
Deviation from 3.579545 MHz
350
350
Hz
Auto-flesh characteristic 73
AF 073
10
20
deg
AF 118
+7
deg
AF 163
20
10
deg
CONT63
10
12
14
dB
CONT32
7.5
6.0
4.5
dB
CONT0
17
14
11
dB
Yf0
6.0
3.5
0.0
dB
[Video Block]
Ctrap
DC propagation
ClampG
Y delay, f0 = 1
YDLY
20
95
100
dB
105
430
%
ns
BKSTmax
13
20
IRE
(normal)
Sharp16
dB
(max)
Sharp31
9.0
11.5
14.0
dB
(min)
Sharp0
6.0
3.5
1.0
dB
RGBBLK
1.4
1.6
1.8
FSTH
0.9
1.2
1.7
ROSDH
220
250
280
IRE
GOSDH
220
250
280
IRE
BOSDH
220
250
280
IRE
RRGB
1.5
1.9
2.3
Ratio
Linearity
LRRGB
45
50
60
GRGB
1.5
1.9
2.3
Ratio
Linearity
LGRGB
45
50
60
BRGB
1.5
1.9
2.3
Ratio
Linearity
LBRGB
45
50
60
BRT64
2.1
2.65
3.2
BRT127
15
20
25
IRE
BRT0
25
20
15
IRE
No. 5844-3/27
LA76070
Continued from preceding page.
Parameter
Cutoff control
(Bias control)
Drive adjustment
Symbol
Conditions
Ratings
min
typ
max
(minimum)
Vbias0
2.1
2.65
3.2
(maximum)
Vbias127
2.45
3.0
3.55
Resolution
Vbiassns
RBout127
2.9
Gout127
2.4
Maximum output
Output attenuation
Unit
V
V
mV/Bit
Vp-p
Vp-p
RBout0
11
dB
Ssync
13
IRE
fH
15600
15734
15850
Hz
fH PULL
400
[Deflection Block]
Sync separator sensitivity
Horizontal free-running frequency
deviation
Horizontal pull-in range
Horizontal output pulse saturation
voltage
V Hsat
HPHCEN
HPHrange
Hz
0.06
0.4
9.5
10.5
11.5
4 bits
HPHstep
VXRAY
0.54
0.64
s
530
ns
0.74
Vsize32
VSIZE: 100000
0.47
0.82
1.17
Vp-p
Vsize0
VSIZE: 000000
0.13
0.48
0.83
Vp-p
Vsize63
VSIZE: 111111
0.80
1.15
1.50
Vp-p
Vdc32
VDC: 100000
3.6
3.8
4.0
Vdc
Vdc0
VDC: 000000
3.2
3.4
3.6
Vdc
Vdc63
VDC: 111111
4.0
4.2
4.4
Vdc
No. 5844-4/27
LA76070
LA76070 BUS: Initial Conditions
Initial test conditions
Register
(continued)
Register
T Enable
0 HEX
Video SW
0 HEX
Video Mute
1 HEX
PLL Tuning
40 HEX
Sync Kill
0 HEX
Audio Mute
1 HEX
AFC Gain
0 HEX
20 HEX
Horizontal Phase
4 HEX
V CD Mode
0 HEX
IF AGC SW
0 HEX
Vertical DC
20 HEX
AFT Defeat
0 HEX
Vertical Kill
0 HEX
RF AGC Delay
20 HEX
Col Kill
0 HEX
Vertical Size
20 HEX
Red Bias
00 HEX
Green Bias
00 HEX
Blue Bias
00 HEX
Blanking Defeat
0 HEX
Red Drive
7F HEX
Blue Drive
7F HEX
0 HEX
Brightness Control
40 HEX
0 HEX
Contrast Control
40 HEX
0 HEX
Auto Flesh
0 HEX
0 HEX
Sharpness Control
10 HEX
0 HEX
Tint Control
40 HEX
0 HEX
Color Control
40 HEX
Vertical Test
0 HEX
Video Level
4 HEX
FM Level
10 HEX
BNI Enable
0 HEX
Audio SW
0 HEX
Volume Control
00 HEX
No. 5844-5/27
LA76070
LA76070 BUS: Control Register Descriptions
Control register descriptions
Register name
Bits
General descriptions
T Enable
Video Mute
Sync Kill
AFC Gain
Horizontal Phase
IF AGC SW
AFT Defeat
RF AGC Delay
Video SW
PLL Tuning
Audio Mute
Vertical DC
Vertical Kill
Color Kill
Vertical Size
Red Bias
Green Bias
Blue Bias
Blanking Defeat
Red Drive
Drive Test
Blue Drive
Brightness Control
Contrast Test
Contrast Control
Sharpness Control
Tint Test
Tint Control
Color Test
Color Control
Vertical Test
Video Level
FM Level
BNI Enable
Audio SW
Volume Control
No. 5844-6/27
LA76070
LA76070 BUS: Control Register Truth Table
Control register truth table
Register name
0 HEX
1 HEX
Test Enable
Test Disable
Audio Mute
Active
Mute
Video Mute
Active
Mute
Sync active
Sync Killed
T Enable
Sync Kill
Slow
Fast
IF AGC SW
AFC Gain
AGC active
AGC Defeat
AFT Defeat
AFT active
AFT Defeat
BNI Enable
BNI active
BNI Defeat
Standard
Non-Stand
Vertical Kill
Vrt active
Vrt Killed
F0 Select
3.58 trap
8.00 APF
AF Off
AF On
Overload Enable
Ovld Off
Ovld On
Normal
Test Mode
Normal
Test Mode
Normal
Test Mode
Normal
Test Mode
Blk Str On
Blanking
No Blank
RGB Mode
C Diff Mode
Normal
No. 5844-7/27
LA76070
LA76070 Bit Map (96.08.01)
IC address: BAH (101111010)
Sub address
MSB
DATA
LSB
D0....D7
DA0
DA1
DA2
DA3
DA4
DA5
DA6
DA7
$00
T_Enable
Vid_Mute
Sync_Kill
AFC Gain
H_Phase
IFAGC SW
AFT DEF
(tr2)
$03
VIDEO SW
(tr3)
$04
Aud_Mute
(tr0)
$01
(tr1)
$02
(tr4)
$05
$06
Ver_kill
Col_kill
(tr6)
$07
$08
(tr11)
$0C
C_Diff
(tr12)
$0D
Cot_Test
G_Bias
0
0
B_Bias
Ver_Size
BLK_DEF
Drv_Test
R_Bias
$0B
Ver_dc
(tr10)
(tr9)
$0A
(tr8)
$09
(tr5)
(tr7)
PLL TUNING
1
V CD MODE
RF_AGC_Delay
0
R_Drive
1
B_Drive
1
Bright
0
Contrast
(tr13)
$0E
A Fresh
Black ST
(tr14)
$0F
Tint_Test
Sharpness
1
0
Tint
(tr15)
$10
Col_Test
(tr16)
$11
Color
(tr17)
V_test
0
$12
VIDEO LEVEL
(tr18)
$13
N/I SW
AUDIO SW
(tr19)
FM LEVEL
0
0
VOLUME
No. 5844-8/27
LA76070
Measurement Conditions at Ta = 25C, VCC = V4 = V26 = 7.6 V, ICC = I21 = 19 mA
Parameter
Symbol
Measurement
point
Input signal
Measurement method
Bus conditions
HVCC
21
I4
(IFICC)
I26
(DEFICC)
26
No signal
Initial conditions
Initial conditions
Initial conditions
No. 5844-9/27
LA76070
VIF Block Input Signals and Measurement Conditions
1. All input signals are applied to PIF IN (pin 10) as shown in the measurement circuit diagrams.
2. The input signal voltage values are all the value of VIF IN (pin 10) as shown in the measurement circuit diagrams.
3. The table below lists the input signals and their levels.
Input signal
Waveform
Condition
SG1
45.75 MHz
SG2
42.17 MHz
SG3
41.25 MHz
SG4
Variable frequency
45.75 MHz
87.5 % video modulation
SG5
45.75 MHz
87.5 % video modulation
Sweep signal
SG6
(APL: 50 IRE
Sweep signal level: 40 IRE)
45.75 MHz
SG7
4. Perform the following D/A converter adjustments in the order listed before testing.
Item
Measurement point
Input signal
Adjustment
APC DAC
13
No signal, IF.AGC.DEF = 1
Set up the DAC value so that the pin 13 DC voltage is as close to 3.8 V as possible
PLL DAC
13
SG1, 93 dB
Set up the DAC value so that the pin 13 DC voltage is as close to 3.8 V as possible
Video
45
SG7, 93 dB
Set up the DAC value so that the pin 45 output level is as close to 2.0 V p-p as
possible
No. 5844-10/27
LA76070
Measurement
Input signal
point
Parameter
Symbol
Measurement procedure
Bus conditions
VAFTn
13
No signal
VOn
45
No signal
[VIF Block]
fPU, fPL
45
SG4
93 dB
VRFH
SG1
91 dB
Set the RF AGC DAC to 0 and measure the pin After performing the adjustments
6 DC voltage
described in section 4
VRFL
SG1
91 dB
RF AGC Delay Pt
(@DAC = 0)
RFAGC0
SG1
RF AGC Delay Pt
(@DAC = 63)
RFAGC63
SG1
VAFTH
13
SG4
93 dB
VAFTL
13
SG4
93 dBz
VAFTS
13
SG4
93 dBz
VO
45
SG7
93 dB
VOtip
45
SG1
93 dB
Input sensitivity
Vi
45
SG7
V/S
45
SG7
100 dB
Differential gain
DG
45
SG5
93 dB
Differential phase
DP
45
SG5
93 dB
SG1
93 dB
SG1
SG2
SG3
S/N
I920
45
45
No. 5844-11/27
LA76070
Video Switch Block - Input Signals and Measurement Conditions
1. Unless otherwise indicated, these measurements are to be performed with no signal applied to PIF IN (pin 10) and
with the D/A converter IF.ACG.SW set to "1".
2. The table below lists the input signals and their labels.
Input signal
Waveform
Condition
SG8
1 V p-p
4.2 MHz
SG9
1 Vp-p
Parameter
Symbol
Measurement
Input signal
point
Measurement procedure
Bus conditions
[VIF Block]
AUXG
AUXS
AUXC
INT0
Pin 1
SG8
VIDEO.SW = "1"
42
Pin 1
SG8
VIDEO.SW = "1"
42
Pin 1
SG8
VIDEO.SW = "0"
42
42
No. 5844-12/27
LA76070
SIF Block (FM Block) - Input Signals and Measurement Conditions
Unless otherwise indicated, set up the following conditions for each of the following measurements.
1. Bus control condition: IF.AGC.DEF = 1
2. SW: IF1 = off
3. Apply the input signal to pin 49 and use a 4.5 MHz carrier signal.
Parameter
FM limiting sensitivity
AM rejection ratio
Symbol
Measurement
point
Input signal
Measurement procedure
Bus conditions
SOADJ
SLS
SF
STHD
90 dB,
Determine the total harmonic distortion in the
fm = 1 kHz,
pin 7 FM detector output 1kHz component
FM = 25 kHz
SAMR
SSN
90 dB,
fm = 1 kHz,
AM = 30%
90 dB,
CW
Measurement procedure
Bus conditions
Maximum gain
Variability range
Frequency characteristics
Muting
Signal-to-noise ratio
Measurement
point
Input signal
51
1 kHz, CW
400m Vrms
VOLUME = "111111"
AUDIO.MUTE = "0"
51
1 kHz, CW
400m Vrms
VOLUME = "000001"
AUDIO.MUTE = "0"
51
20 kHz, CW
400m Vrms
VOLUME = "111111"
AUDIO.MUTE = "0"
AMUTE
51
20 kHz, CW
400m Vrms
VOLUME = "000000"
AUDIO.MUTE = "0"
ATHD
51
1 kHz, CW
400m Vrms
VOLUME = "111111"
AUDIO.MUTE = "0"
VOLUME = "111111"
AUDIO.MUTE = "0"
Symbol
AGMAX
ARANGE
AF
ASN
51
No signal
No. 5844-13/27
LA76070
Chrominance Block - Input Signals and Measurement Conditions
Unless otherwise indicated, set up the following conditions for each of the following measurements.
1. VIF and SIF blocks: No signal
2. Deflection block: Input a horizontal and vertical composite synchronizing signal, and assure that the deflection block
is locked to the synchronizing signal. (Refer to the Deflection Block - Input Signals and Measurement Conditions
section.)
3. Bus control conditions: All conditions set to the initial conditions unless otherwise specified.
4. Y input: No signal
5. C input: The C1IN input (pin 40) must be used.
6. The following describes the method for calculating the demodulation angle.
B-Y axis angle = tan-1 (B (0)/B (270) + 270
R-Y axis angle = tan-1 (R (180)/R (90) + 90
G-Y axis angle = tan-1 (G (270)/G (180) + 180
R-Y axis
B-Y axis
G-Y axis
[R-Y/B-YSin BR-Cos ]
No. 5844-14/27
LA76070
Chrominance Input Signals
C-1
C-2
C-3
(However, if a frequency is specified that frequency must be used.)
C-4
C-5
No. 5844-15/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
[Chroma Block]
Bout
ACC amplitude characteristic 1
ACCM1
ACCM2
30
C-1
0 dB
+6 dB
C-1
14 dB
Bout
30
YIN: L77
C-1:
No signal
B-Y/Y amplitude ratio
CLRBY
C-2
30
CLRMN
30
C-3
CLRMN
30
C-3
TR28:
Saturation
00000000
TR24:
Saturation
01011010
Saturation
00100110
CLRSE
30
C-3
Tint center
TINCEN
30
C-1
TR23: Tint
00111111
TINMAX
30
C-1
TR23: Tint
01111111
TINMIN
30
C-1
TR23: Tint
00000000
C-1
C-3
TR24:
Saturation
01000000
C-3
TR24:
Saturation
01000000
TINSE
30
30
RB
28
Demodulation output ratio
G-Y/B-Y
GB
29
No. 5844-16/27
LA76070
Continued from preceding page.
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
C-1
ANGBR
30
28
ANGBG
29
C-1
KILL
30
C-3
CVCOF
15
CIN
No signal
PULIN +
PULIN
30
30
C1
C1
C4
TR22:
Auto flesh:
0*******
TR22:
Auto flesh:
1*******
C4
TR22:
Auto flesh:
0*******
TR22:
Auto flesh:
1*******
C4
TR22:
Auto flesh:
0*******
TR22:
Auto flesh:
1*******
30
Auto flesh characteristic 73
AF073
28
30
Auto flesh characteristic 118
AF118
28
30
Auto flesh characteristic 163
AF163
28
No. 5844-17/27
LA76070
Video Block - Input Signals and Measurement Conditions
C IN input signal * chrominance burst signal: 40 IRE
Y IN input signal 100 IRE: 714 mV
*0 IRE signal (L-0): Standard NTSC synchronizing signal
CW signal (L-CW)
No. 5844-18/27
LA76070
Symbol
Measurement
point
Input signal
CONT127
30
L50
Contrast max
1111111
Contrast adjustment
characteristics
(normal/maximum)
CONT63
30
L50
Contrast center
0111111
Contrast adjustment
characteristics
(minimum/maximum)
CONT0
30
L50
Contrast min
0000000
L0
Brightness min
0000000
Contrast max
1111111
Brightness min
0000000
Contrast max
1111111
Parameter
Measurement procedure
[Video Block]
30
DC propagation
ClampG
30
L100
Y delay
YDLY
30
Measure the output signal 0 IRE DC level at
point A when the black stretch function is
BKST defeat on (1)
defeated (off). Record this value as BKST1 (V).
BKSTmax
30
LBK
30
Sharpness (peaking)
LCW
LCW
Horizontal/vertical blanking
output level
RGBBLK
30
L100
No. 5844-19/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
FSTH
30
L0
O2
L50
L0
O2
L50
L0
O2
L50
L0
O2
L0
O1
Measurement procedure
[OSD Block]
OSD fast switch threshold
ROSDH
28
GOSDH
29
BOSDH
30
28
Gain matching
RRGB
Linearity
LRRGB
29
L0
O1
Gain matching
GRGB
Linearity
LGRGB
30
L0
O1
Gain matching
BRGB
Linearity
LBRGB
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
28
Brightness control (normal)
BRT63
29
30
(max)
(min)
BRT127
BRT0
L0
Contrast max
1111111
Calculate BRT63 as
(BRTPCR + BRTPCG + BRTPCB)/3
Measure the output signal 0 IRE DC levels for
Brightness max
the B output (30). Record this value as BRTPHB. 1111111
30
Calculate BRT127 as
50 (BRTPHB BRTPCB)/CNTHB
Measure the output signal 0 IRE DC levels for
Brightness min
the B output (30). Record this value as BRTPLB. 0000000
Calculate BRT0 as
50 (BRTPLB BRTPCB)/CNTHB
No. 5844-20/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
Vbias0
L50
(maximum)
Vbias127
R bias max
1111111
G bias max
1111111
B bias max
1111111
Contrast max
1111111
R bias:
1010000
G bias:
1010000
B bias:
1010000
Contrast max
1111111
R bias:
0110000
G bias:
0110000
B bias:
0110000
Contrast max
1111111
28
29
30
Bias (cutoff) control resolution
Vbiassns
28
Output attenuation
RGBout0
29
30
L100
Contrast max
1111111
Brightness min
0000000
Contrast max
1111111
Measure the output signal 100 IRE amplitudes
Brightness min
for the R output (pin 28), G output (pin 29), and
0000000
B output (pin 30). Record these values as
R drive min
DRVL* (V p-p).
0000000
Here, * is R, G, and B, respectively.
B drive min
0000000
RGBout0* = 20 log (DRVH*/DRVL*)
No. 5844-21/27
LA76070
Deflection Block - Input Signals and Measurement Conditions
Unless otherwise indicated, set up the following conditions for each of the following measurements.
1. VIF and SIF blocks: No signal
2. C input: No signal
3. SYNC input: Horizontal and vertical composite synchronizing signal (40 IRE and other conditions, such as timing,
must conform to the FCC broadcast standards.)
Caution: The burst and chrominance signals must not be below the pedestal level.
4. Bus control conditions: All conditions set to the initial conditions unless otherwise specified.
5. The delay between the rise of the horizontal output (the pin 23 output) and the rise of the F.B.P IN (the pin 24 input)
must be 9 s.
6. Unless otherwise specified, pin 25 (the X-ray protection circuit input) must be connected to ground.
Caution:
Perform the following operation if horizontal pulse output has stopped.
1. The bus data T_ENABLE bit must be temporarily set to 0 and then set to 1.
(If the X-ray protection circuit operates, an IC internal latch circuit will be set. To reset that latch circuit, the
T_ENABLE bit must be temporarily set to 0, even if there is no horizontal output signal being output.)
Notes on Video Muting
If horizontal pulse output has stopped, perform the operation described in item 1. above and then set the video mute bit
set to 0.
(This is because the video mute bit is forcibly set to the mute setting when the T_ENABLE bit is set to 0 or when the Xray protection circuit operates. This also applies when power is first applied.)
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
37
SYNC IN:
horizontal and
vertical
synchronizing
signal
Bus conditions
[Deflection Block]
Horizontal free-running
frequency deviation
Ssync
fH
fH PULL
V Hsat
23
SYNC IN:
No signal
37
SYNC IN:
horizontal and
vertical
synchronizing
signal
23
SYNC IN:
horizontal and
Measure the voltage during the low-level period
vertical
in the pin 23 horizontal output pulse
synchronizing
signal
No. 5844-22/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
Bus conditions
23
Horizontal output pulse phase
HPHCEN
37
23
HPHrange
37
23
HPHstep
37
23
VXRAY
25
SYNC IN:
horizontal and
vertical
synchronizing
signal
SYNC IN:
horizontal and
vertical
synchronizing
signal
SYNC IN:
horizontal and
vertical
synchronizing
signal
SYNC IN:
horizontal and
vertical
synchronizing
signal
Hphase:
000
Hphase:
111
Hphase:
000
to
Hphase:
111
No. 5844-23/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
Bus conditions
Vsize32
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
Vsize0
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
VSIZE:
0000000
Vsize63
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
No. 5844-24/27
LA76070
Parameter
Symbol
Measurement
point
Input signal
Measurement procedure
Bus conditions
Vdc32
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
Vdc0
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
VDC: 0000000
Vdc63
17
SYNC IN:
horizontal
and
vertical
synchronizing
signal
VDC: 1111111
No. 5844-25/27
LA76070
No. 5844-26/27
LA76070
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customers
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customers products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the Delivery Specification
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of July, 1999. Specifications and information herein are subject to
change without notice.
PS No. 5844-27/27