Professional Documents
Culture Documents
Sanitec WTE MDU Tech Enviro Specs
Sanitec WTE MDU Tech Enviro Specs
MEDICAL WASTE
MICROWAVE DISINFECTION
UNIT
TECHNICAL DESCRIPTION
&
ENVIRONMENTAL
PERFORMANCE
Page 1 of 27
Table of Contents
Section
1
GENERAL INFORMATION
1.1
1.2
3
3
Introduction
Technical Data
Page
4
5
7
10
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
10
10
11
12
13
13
15
16
16
16
16
17
18
18
19
20
Introduction
System Overview
Charging System
In-Feed Hopper & Feed Arm
Extraction System
Shredder Assembly
Transfer Hopper
Microwave Section (MWS)
Steam Application
Temperature Control & Faults
Microwave Generators (MWGs)
MWS Operation
Temperature Holding Section (THS)
THS Hopper
THS Discharge Conveyor
Auxiliary Equipment
SYSTEM PERFORMANCE
23
3.1
3.2
3.3
3.4
3.5
23
25
26
26
27
Page 2 of 27
GENERAL INFORMATION
1 - 1.
INTRODUCTION
This document contains technical information for the Microwave Disinfection Unit (MDU) Model
HG-A-250S. The MDU is a product of SANITEC of Sun Valley, California.
The document is written to provide the necessary functional explanation of components and the
overall system so one can fully understand how the SANITEC MDU processing medical infectious
waste with absolute certainty.
The Sanitec Microwave Disinfection Unit (MDU) is designed to shred and disinfect biomedical
waste. When operated in accordance with all of Sanitec's written procedures and instructions,
properly operated systems will render biomedical waste disinfected, unrecognizable, and of no
greater risk to the public health than (normally associated with) residential household waste.
The disinfection process is computer controlled with an Allen-Bradley Touch Screen system.
Under normal operating conditions (automatic mode), operators need only charge the system
with biomedical waste. The Unit has a hydraulic lift mechanism to hoist waste containers and
drop waste into a hopper on top of the unit. The hopper has a sealed lid that opens and closes
automatically. Inside the hopper, the bags and boxes of waste are directed towards a shredding
device by a feed arm. The feed arm assists in forcing material into the shredder. Sensors
monitor the amount of material moving into the hopper. Shredded material falls onto an augerdriven conveyor. As the waste enters the auger-driven conveyor, 162 0C (324 0F) steam is
injected and conveyed through the microwave conveyor section. A series of microwave
generators input energy to maintain uniform heating of the waste at a minimum temperature of
95 0C (203 0F). The waste is then transported to a Temperature Holding Section.] The final
temperature and time profile is a minimum of 95 0C (203 0F) for 30 minutes. The final waste
product then falls into a dumpster or similar waste transport container that may be used to
transport the disinfected waste to a repository. Figure 1-1 shows a graphic illustration of the
MDU and its subsystems.
The SANITEC MDU exceeds the efficacy performance requirements of the State and Territorial
Association on Alternative Treatment Technologies (STAATT) achieving greater than log 4
reduction of bacterial spores. The SANITEC MDU has been approved or accepted throughout
the US and in many countries around the world.
.
1-2.
TECHNICAL DATA
The overall pertinent technical characteristics of the MDU are listed in Table 1-1. The
identification and technical characteristics of units/systems associated with the MDU are listed in
Table 1-2.
Page 3 of 27
GENERAL INFORMATION
In-feed Hopper
Door (Flap)
HEPA/ACF Extraction
System
MDU Inside
Control Panel
In-feed Hopper
Microwave
Generators (6)
Hydraulic Waste
Cart Charging
System
Temperature
Holding Section&
Discharge Screw
Outside
Operator Panel
Lift Controls
Waste Transfer
Hopper
Waste Shredder
Assembly
Microwave
Treatment Section
Page 4 of 27
GENERAL INFORMATION
TABLE 1 - 1
PARAMETER
SPECIFICATIONS
Overall Dimensions
Length
Width
Height
Height With Flap Open
Weight
Water Connection
460/480 VAC
150Amps
3 phase (with ground)
60 Hz
85 kW
400/380 VAC
200 Amps
3 phase (with ground)
50 Hz
85 kW
Page 5 of 27
GENERAL INFORMATION
SPECIFICATIONS
Hopper Door
Waste Cart
Charging System
Hydraulic Cylinder
Charging Frame
In-feed Hopper
Size
Feed Arm
Steam Connection
Water Connection
Insulation
2 in. thick
Air Capacity
Differential Pressure
Gauge
Pre-filter Cartridge
HEPA Filter
ACF
Page 6 of 27
GENERAL INFORMATION
SPECIFICATIONS
Motor
Shredding Assembly,
Reversible
Transfer Hopper
Microwave Section
Cutting Blades
Cutting Screen
Gear Reducer
TXT8
Belt
Belt
Size
Sight Glass
Photo Sensors
Capacitive type
Microwave Housing
Screw
Drive Motor
Insulation
Temperature Sensor
Page 7 of 27
GENERAL INFORMATION
Microwave
Generator
(Quantity 6)
Temperature
Holding Section
(THS)
Treated Waste
Discharge Screw
(THS Screw)
SPECIFICATIONS
HF Output Power
1.25 kW
Output frequency
2,450 MHz
Electrical Power
Requirements
Power Consumption
2.1 kW
Sight Glass
Temperature Sensor
Pipe Diameter
Screw Diameter
Flight Length
Drive Motor
Built-in Electric
Steam Generator
Steam Capacity
Steam Temperature
Electrical Power
Requirements
Power Consumption
60 KW
Page 8 of 27
GENERAL INFORMATION
SPECIFICATIONS
Oil Capacity
Hydraulic System
Enclosure
Ventilation Fan and
Automatic Louvers
Microwave Survey
Meter
Pump Pressure
Additional
Components
Supplied
Electrical Power
Requirements
Air Capacity
Size
Electrical Power
Requirements
Operating Ranges
Power
Requirements
Electrical Power
Requirements
Water Pump
Inlet/Outlet Port
Capacity
Soap Dispenser
Antibacterial, 1 Liter
OMM
Page 9 of 27
2-1
INTRODUCTION
This chapter describes the functional operation of each of the subsystems and equipment of the
MDU necessary for achieving medical waste disinfection. Descriptions are arranged in order of
operation.
2-2
SYSTEM OVERVIEW
The MDU disinfects infectious medical waste through the application of steam and microwave
radiation. The infectious material is temporarily held in a waste container(s), which in turn, are
emptied into an in-feed hopper via a charging system. The charging system is located at the
front of the MDU. The infectious waste is fed to a shredder by the feed arm where it is shredded.
The shredded material is conveyed through the microwave section and temperature holding
section, respectively for disinfection. The outlet of the temperature holding section protrudes near
the back end of the unit and is designed to transport the disinfected waste into waste disposal
containers (or compaction units). From there the material can be transported to a local municipal
landfill for disposal or to a refuse recycling plant or wherever ordinary household solid waste is
disposed.
The MDU is designed to run automatically with a minimum of operator intervention. The MDU
components are enclosed in a weather-resistant steel enclosure, and are suitable for an outdoor
operation. The MDU is comprised of the following subsystems.
a.
b.
c.
d.
e.
f.
g.
Charging System
In-feed Hopper & Feed Arm
Extraction System
Shredder Assembly
Transfer Hopper
Microwave Section
Temperature Holding Section & Discharge Screw
The aforementioned subsystems are described in subsequent paragraphs of this chapter. Please
refer to Figure 1-1 graphic illustration to find depiction of the system components and subsection
discussed herein.
Page 10 of 27
CHARGING SYSTEM
The charging system is used for loading the infectious waste into the in-feed hopper. This
operation is controlled via the Operators Control Panel.
The charging system consists of a hydraulically operated lift assembly and in-feed hopper door
(flap) through which the waste container (up to 1 cubic yard or 880 liters) is emptied. The infeed hopper flap is raised and lowered by two hydraulic cylinders mounted on the MDU roof. A
carriage assembly is attached to the hopper flap by means of a connecting rod, which runs inside
U-shaped guide rails. The rails are fitted vertically along the front end of the unit. So, as the
hopper flap is opened, the carriage raises the waste container. The carriage can be modified to
accommodate waste carts supplied by various manufacturers.
The in-feed hopper door (flap) assembly is fitted with two proximity switches, which detect the
position of the flap. The flap's position, open or closed, is fed from the respective switch to the
Programmable Logic Controller (PLC), which controls the charging operation. As the in-feed hopper
flap comes to its fully opened position, the waste container is tipped, allowing the waste to fall
into the in-feed hopper. The tipping operation is complete when the flap has reached its
maximum opening. Once the waste container has been emptied (waste container fully tipped),
the carriage assembly must be moved to its lowest position to ensure that the flap is completely
closed and the waste container is down. If the flap is not fully closed, the shredding system will
not start. After the waste has been charged into the system and the flap is fully closed, the unit
continues automatic operation and the shredding system will operate.
The operating sequence of the charging system commences when the operator acknowledges
a system charge request by momentarily pressing the LIFT UP push button switch. The system
runs through its pre-charging sequence, and starts the hydraulic power unit operating. The
operator's lift up and lift down controls are enabled allowing the operator to charge the system.
When the lift reaches the full up position, the flap-open proximity switch is activated, stopping
the lift up operation via the PLC. The action of reaching the full up position indicates to the PLC
that the waste has been transferred from the container to the hopper. When the lift reaches the
full down position, the flap closed proximity switch (30) is activated, stopping the lift down
operation via the PLC. If the lift has traveled from the full up position and then to the full down
position, the PLC will recognize that the charging operation has been completed and the
hydraulic unit will discontinue operation.
Page 11 of 27
The In-feed Hopper is fitted with a rotating feed arm, located inside the hopper. The feed arm
ensures uniform feeding of waste into the shredder blades. On the opposite side of the feed arm
motor, there is one proximity switch. The switch detects the position of the feed arm during
charging. The feed arm must be positioned so that waste entering the hopper is not restricted.
The same switch counts the revolutions of the feed arm as it turns and reverses direction.
The feed arm operating sequence is delayed after charging the MDU allowing the waste to be
gravity fed to the shredder. After the delay, the feed arm operation commences. As it turns it
encounters resistance due to waste build up. As the resistance increases, the current draw of
the motor also increases. When the current draw reaches a certain level, a current relay is
actuated signaling the PLC of the high current condition. The PLC in turn stops the feed arm
motor, waits five seconds for the motor to stop rotating, and then reverses the motor's
direction. The feed arm operates in reverse until excessive resistance is again encountered or
the feed arm has rotated in reverse to the six o'clock position. The PLC will then stop the feed
arm motor and wait five seconds for the motor to stop rotating.
The process is then repeated when the feed arm is rotating in the forward direction. When the
feed arm makes four full revolutions in the forward direction without tripping the current relay, the
PLC assumes that the hopper is empty and calls for system charging. The operator cannot feed
waste into the MDU unless the PLC determines that the hopper is empty and the MDU is
operating properly.
The in-feed hopper is also fitted with four steam injection nozzles and four water spray nozzles.
Steam and water are used to prepare the in-fed hopper to receive waste. Steam is used to
manually disinfect the in-feed hopper. The hopper walls are thermally insulated to hold in the
steam temperature.
When the hopper is empty, and ready for another charge, steam is injected during the charge
preparation to fully saturate the hopper area. After the steam is injected and held, water is sprayed
into the in-feed hopper to quench the interior and condense the steam. The extraction system then
turns on to evacuate the steam from the hopper. This sequence also accomplishes abatement of air
borne pathogen emissions from creating an unsafe working environment. This entire
decontamination sequence is automatically initiated by the PLC when the MDU is ready to receive
another charge of waste. The hydraulic waste charging system will not operate until this sequence is
completed. At that point, the operator will hear an alarm and see the LIFT-UP button lamp
illuminated, only then will the lift controls function.
Page 12 of 27
2 - 5 EXTRACTION SYSTEM
The Extraction System is used to evacuate steam from the in-feed hopper during the charging
sequence. The extraction damper opens a duct to the extraction filter assembly, which draws
(extracts) the steam and air from the in-feed hopper prior to and during the waste charging
sequence. An inlet damper on the in-feed hopper flap allows outside air to pass into the in-feed
hopper thereby evacuating the hopper volume numerous times before the hopper flap is
electronically allowed to open.
Operation of the extraction system commences after water is sprayed to quench the hopper.
After the water spray is completed, the extraction blower is started. The extraction blower extracts
steam and air through the pre-filter, high efficiency particulate air filter (HEPA) and activated carbon
filter (ACF), before discharging to atmosphere. The system is designed to achieve over 11 hopper
volume air changes before the hopper flap is allowed to open. This feature simulates criteria used in
isolation room for highly infectious airborne diseases in hospitals to ensure maximum safety.
After the steam and air has been extracted from the in-feed hopper, the operator's lift controls are
enabled, allowing the system to be charged. When the charging sequence is completed and the
in-feed hopper flap is fully closed, sensed by the flap-closed proximity switch, the extraction
blower is turned off. When the extraction blower is off, the extraction and inlet dampers close.
When the extraction system is in operation, the pressure drop across the HEPA filter is measured
by an analog type manometer located near the filter housing. The pressure drop is used to
indicate the efficiency of the filter and thereby the amount of contamination that the filter has
collected. As the filter becomes progressively more contaminated, the pressure drop across the
filter increases. A pre-filter is used to extract moisture from the air. The filters must be replaced
when the pressure drop reaches approximately 3 in of WG (0.75 Kpa).
Extraction drain line valves are located beneath the HEPA filter and carbon filter housing.
These valves are to be normally closed and only opened daily, to drain liquid from these
housings back into the front of the microwave treatment section.
2 - 6 SHREDDER ASSEMBLY
The shredder assembly is fed waste material from the in-feed hopper by the feed arm. The waste
is shredded to a size that can be easily conveyed and effectively disinfected.
Page 13 of 27
Shredding pre-conditions the to ensure that all items, such as suction canisters and other
items that can not be effectively treated by traditional autoclaves, are broken apart and all
infectious surfaces are exposed to treatment conditions
Shredded material allows for more efficient heat transfer, therefore the MDU uses
substantially less energy than traditional devices
The shredder assembly consists of a rectangular frame housing with cutter shafts employing
twin blades (cutting element) and a single speed motor, which drives the cutter shafts in opposite
directions via a spur gear. The cutting element is designed to allow the projection of one blade to
engage in the recess of the opposite blade, while cutting at the same time. In this way, shredding
over the total circumference of the blade is achieved. In order to obtain even shredding over the
entire length of the shaft, the blades are offset on the shafts.
A screen is installed beneath the shredder system to control the degree of shredding. If the
shredded material is too large to fall through the screen it is forced up, around the sides of the
shredder and recycled back through the cutter blades. The material is continually recycled this
way until it has been reduced to the size governed by the screen, allowing it to pass through to the
rest of the system for treatment.
The shredder is controlled by two different sources. They consist of the high and low photo
switches located on the transfer hopper and a current sensing relay, located in the Main Control
Cabinet. Since reversing of the shredder is an integral part of the operation, the relay is used to
control the shredder (via the PLC) by monitoring the current draw on the shredder motor. If the
current draw exceeds the factory set limit of 40 amperes, the shredder will come to a stop. The
shredder will then automatically run in reverse enabling the cutter blades to be released. After a
short time of running in reverse, the shredder will then come to a stop and resume rotating in the
forward direction. The reversing operation also occurs whenever the shredder is starting from a
stopped position. If a number of reversals occur in a programmed amount of time, the PLC will
automatically shut the shredder down and the system will go to the fault mode. As the material
is shredded to its proper size, it falls into the transfer hopper before moving on through the
systems.
Page 14 of 27
2 - 7 TRANSFER HOPPER
The transfer hopper is flange mounted between the shredder and the front end of the microwave
conveying section. The transfer hopper, which is welded to the microwave section, is used as an
intermediate storage for the shredder waste and controls the supply of material to the microwave
screw.
The shredder supplies an adequate amount of material for processing in the microwave section.
The transfer hopper is fitted with photo switch sensors that provide feedback signals to the PLC,
which controls internal timers to prevent false photo switch signaling. The PLC receives and
outputs control signals in response to the following conditions.
a.
Material below Low Level - Indicates that there is insufficient material for the
proper operation of the microwave section (indicated by the low level photo
switch). The shredder will operate but the microwave section (MWS) will stop. If the
material stays below low level for a predetermined time, the MWS MATERIAL
LEVEL will go to fault.
b.
Material between Low and High Levels - Indicates that there is a sufficient amount
of material for proper operation of the microwave segment. Both the shredder and
microwave segment operate.
c.
Material above High Level - The shredder will stop when the material remains at
high level for a predetermined time. The MWS MATERIAL LEVEL will go to fault
after predetermined time.
This control method cycles the shredder, thus the level in the transfer hopper continually
fluctuates, providing a proper flow of material to the microwave section.
The transfer hopper is also fitted with a liquid level sensor for detection of an excessive amount of
liquid. The sensor is used to ensure that the hopper does not fill up with liquid, which can cause
problems during operation. In the event excess liquid is detected, the System warns of impending
shut down by flashing the MWS LIQUID LEVEL lamp on the Touch Screen. After a delay, the
enunciator warning horn sounds and the system goes to fault.
The transfer hopper is also equipped with a sample entry point located below the shredder to
allow the insertion of microbiological test specimens for the testing of disinfection performance.
Page 15 of 27
The microwave section heats the shredded waste in a continuous operation. Heating is achieved by
steam injection and microwave radiation applied as the material passes through the MWS.
2-9
STEAM APPLICATION
At a predetermined distance from the transfer hopper, before MWG#1, steam is injected into the
MWS by four (4) steam nozzles. Steam is used to maintain the temperature of the waste and
provides the proper environment for the microwave energy to perform disinfection.
2 - 10
Microwave radiation is introduced along the length of the microwave segment by six (6)
microwave generators (MWG). A temperature sensor located between MWG #2 and MWG #3
monitors the MWS Entry Temperature. If low temperature exists for too long a period of time, the
MWS Entry Temperature will go to fault. A temperature sensor located between MWG #5 and
MWG #6, monitors the temperature of the material as it exits the MWS (MWS Exit Temperature).
During system operation the MWS screw speed is determined by the MWS Exit Temperature. If
the material temperature is below 203 0F (95 0C), the MWS screw will run at 50% full speed.
If the material temperature is 203 0F (95 0C) or above, the MWS screw will run at 100% (Full
Speed). The MWS Exit Temperature is enabled when MWG #5 is enabled. The MWS Exit
Temperature will go to fault after 5 minutes of low temperature only when enabled.
2 - 11
The MWGs input the microwave energy necessary to maintain the operating temperature above
the set-point to ensure waste disinfection. The MWGs are installed in specially designed stainless
steel housing, and (together with HF sealing) are bolted onto the wave-guides via the resonance
chamber. The control and power supply wires are fitted with plug-in connectors to facilitate
VHUYLFH 7KH 0:*V VXSSO\
1250 ZDWWV RI RXWSXW power at a frequency of 2,450 MHz. A built-in
hour meter indicates the total operating hours of the MWG preheating filament. A radial fan is
located inside each MWG housing cools the magnetron tubes. It is important therefore that the air
inlet and outlet vents are kept clean to allow proper circulation. Keeping the MDU doors closed will
help prevent dirt and dust from fouling the MWG air vents.
Page 16 of 27
An interlock switch is installed on each microwave generators mounting base. This interlock
disconnects power to the microwave generator when removed from the operational position.
Each MWG is monitored by a watchdog Timer within its stainless steel housing. If the current
draw of a generator is not within a preset range, the system will signal a fault. Should a MWG
be out of service, the MWG power and control can be manually switched off at the control
cabinet. A minimum of four MWGs must be on for the system to operate.
2 - 12
MWS OPERATION
The MWS operates independently of the charging operation and microwave generation takes
place only under the following conditions:
When the microwave screw conveyor has a sufficient amount of material and:
The transfer hopper photo switches must indicate that a sufficient level (supply) of material exists.
The MWG fan must be operating before the MWS screw can turn. The fan forces air between the
wave-guide and window of each MWG to prevent condensation and sparking.
A proximity switch located at the screw conveyor's gear motor screw shaft, counts the number of
revolutions of the screw. After the MWS screw has completed its first revolution (after start-up)
steam is pulse injected. After a total of six revolutions, the first microwave generator (MWG) will
turn on (become enabled). At this time steam injection changes to a continuous injection when the
MWS screw is turning and pulse injection when the MWS is off. After two additional revolutions,
the second MWG will become enabled. Every second revolution thereafter, the next MWG in turn
will become enabled until all selected MWG are on.
After all selected MWG units are enabled (on), the steam injection changes to a pulsed
injection, whether the MWS screw is turning or not turning.
Page 17 of 27
2 - 0:623(5$7,21&RQWG
When the system is selected to perform automatic shutdown, and the transfer hopper signals that
\t LVHPSW\VKXWGRZQRIWKH0:*VZLOOEHJLQ$IWHUILYHUHYROXWLRQVRIWKHPLFURZDYHVFUHZWKH
first MWG will shutdown (become disabled) and the MWS Entry Temperature will be disabled.
After one additional revolution, the second MWG will be disabled. After each additional
revolution, the next MWG in turn will be disabled until all VHOHFWHG0:*VDUHRII:KHQDOO0:*
units are disabled (off) the steam injection will turn off for the remainder of the shutdown
sequence and the MWS Exit Temperature will be disabled. This shutdown sequence ensures that
all waste material is treated before exiting the microwave section and entering the temperature
holding section.
The MWG operation is interlocked with the unit's door and each MWG is interlocked with a key
type safety switch as a protective measure for personnel safety. Should the door be opened
while the system is operating, the MWGs will shutdown and will not restart until the door is closed.
The rest of the system will continue to operate as long as the temperature remains at
operational levels. If the door, however, is left open for an extended period, the system
temperature will drop, causing the system to go into a fault condition and stop. The door open
switch can be over-ridden, to allow for testing and maintenance of the system by qualified
personnel.
2 - 13
The Temperature Holding Section (THS) is the final stage of the disinfection process. The THS
consists of two component areas; the hopper and the discharge conveyor.
2 - 14
THS HOPPER
The THS hopper is thermally insulated to prevent internal cooling and is flange mounted to the
exit end of the Microwave Section (MWS). As treated material exits the MWS, it falls into the
hopper of the Temperature Holding Section (THS). The material is retained in this section as part of
the disinfection process and the material, temperature is monitored as part of the control process.
The hopper is also used to compensate for variances in the flow of treated material between the
MWS and the THS discharge screw. High and Low level photo sensors mounted in the hopper
provide feedback signals to the PLC, which controls internal timers to prevent false photo switch
signaling. The PLC in turn outputs control signals in response to the following conditions:
Page 18 of 27
2 - 7+6+233(5&RQWG
a.
Material below Low Level - Indicates that there is insufficient material in the
THS hopper. Under this condition the MWS screw conveyor continues to operate
but operation of the THS discharge conveyor is temporarily disabled. After a
period of time below low level, the system goes to fault.
b.
Material between Low and High Level - Indicates that the hopper level is
satisfactory. The MWS conveyor and THS discharge screw conveyor will operate
normally.
Material above High Level - Indicates that the THS hopper is full, causing the
MWS screw conveyor to stop. If the material remains at high level for a
predetermined time, the THS MATERIAL LEVEL will go to fault. When the
material level falls below the high-level photo switch, a time delay will allow the
MWS screw conveyor to restart. This control method cycles the MWS and THS
screw conveyors so that the THS Hopper material level remains relatively
constant, during automatic operation, thereby providing a proper flow of
discharging material.
c.
2 - 15
The THS discharge screw conveyor is mounted to the bottom of the hopper and is supported by
a stand that is located outside of the unit. It is used to feed the disinfected waste into the
granulator or discharge the disinfected waste from the unit directly into a waste container, which
is positioned directly below the outlet.
A temperature sensor is located at the bottom of the THS hopper section just above the entry
area to the THS screw conveyor (THS exit temperature). This sensor monitors temperature of
the waste in the THS. The THS exit temperature sensor becomes enabled when MWG#6 is
enabled. The temperature must be 95C or greater. If the temperature stays below 95C for five
minutes, the THS exit temperature will go to fault.
The bottom portion of the THS discharge conveyor is insulated to protect personnel from bums
that can occur due to the high -internal temperatures. The upper portion is not insulated to
condense any residual steam and allow the material to cool down before it exits the conveyor.
Page 19 of 27
AUXILIARY EQUIPMENT
The MDU auxiliary equipment consists of separate items that perform specific functions in
support of the waste disinfection process. The following paragraphs describe this equipment.
2 17
STEAM GENERATOR
The PLC monitors the steam generator and determines its operating status. Upon automatic
start-up, the steam generator begins to warm up. When the steam temperature reaches 150 0C
the PLC starts the system. If this temperature is not reached within several minutes, the system
will go to fault. If the steam temperature drops below 150 0C and does not recover after a period of
time, the system goes into "sleep mode". In the "sleep mode" the system is automatically
stopped to allow the steam generator time to recover (steam generator remains ON). When the
system is in sleep mode, the PLC waits for the steam temperature to reach 150 0C before
returning the system to automatic operation. This assures that the steam generator has built up
a sufficient supply of steam. If this temperature is not reached after several minutes, the system
will go to fault.
2 18
HYDRAULIC UNIT
The hydraulic unit is used for operating the charging system. The unit is completely selfcontained consisting of a pump, reservoir and solenoid valves.
2 19
The water pump supplies water at low pressure to the spray nozzles located at the in-feed
hopper and over each viewing glass in both the transfer and THS hopper. At the in-feed hopper,
water is sprayed during the charge preparation sequence to quench the hopper's interior and
condense steam that was previously injected. At the transfer and THS hoppers, water spray is
used to wash away material so that the photo switches have an unrestricted path through the
viewing windows, thereby allowing proper operational control. The PLC engages the water
pump and spray valve under the following conditions:
a. When the viewing glass is blocked due to high level of material in the transfer
hopper.
b. At the transfer hopper, water is sprayed on the viewing glass every three
revolutions of the MWS screw. This ensures that the photo switches are always
reading the correct material level.
c. Whenever the SPRAY push button is pressed on the Main Control Cabinet. The
switch must be released and pressed a second time to produce another spray.
Page 20 of 27
VENTILATION SYSTEM
The MDU ventilation system is comprised of a thermostatically controlled fan with mechanical
louvers at the discharge end of the MDU, and a motor driven louver, located at the charging end
of the unit. Both sets of louvers, open and close, as the fan turns on and off, automatically
drawing air through the MDU.
Since power for the ventilation system is always on, it may not be unusual for the fan to turn on by
itself even though the system is not operating. The thermostat is located on the same wall as the
extraction filter and has been factory preset to operate at approximately 80 0F (26.6 0C).
2 21
INTERIOR LIGHTS
There are three types of fluorescent light fixtures attached to the ceiling of the unit. They consist
of a single 40-watt fixture located next to the in-feed hopper (man door Side), a double 96-watt
fixture located over the length of the MWS and a double 40-watt fixture located next to the infeed hopper (shredder motor side). A light switch is conveniently located at the entrance door,
inside the shelter.
2 22
The door open over-ride switch is a key-type switch located next to the interior light switch. The
over-ride switch allows trained personnel to operate the system, with the door open while the
MWGs are operating. The switch is used for maintenance purposes only and should not be used
during normal system operation. It is important that the switch be turned off to assure safety of
personnel.
2 23
OUTLET RECEPTACLES
The MDU is fitted with ground fault interrupt type, duplex outlet receptacles. They consist of the
following:
a. Three brown outlets, for space heaters (15 amps).
b. Two duplex outlets with ground fault protection, located inside the MDU for
general use
c. Two duplex outlets with Ground Fault Protection, located outside the MDU
for general use.
Page 21 of 27
The distribution panel is located to the right of the Main Control Cabinet and houses
circuit breakers for all 120VAC devices. A circuit breaker panel, located above the
distribution panel, serves as a disconnect switch and protection device for the distribution
panel.
Page 22 of 27
SYSTEM PERFOMANCE
The SANITEC MDU has been one of the most scientifically challenged and tested technologies
available on the world market. Testing has been successfully performed for many individual states
in the US and for many countries around the world,. including the UK, Japan, France, Germany and
others. The document presents a summary of information. Copies of actual test studies and reports
can be made available upon request.
3 1 MICROBIOLOIGICAL TESTING & RESULTS
The most challenging and comprehensive testing ever performed were for the New York State
Department of Health in the US. This test required the processing of microbiological samples from
all microbiological categories in order to prove successful efficacy. These particular testing
methodology ultimately become the forerunner of the first STAATT guideline published for the
evaluation of medical waste treatment technologies:
Organism
ATCC Strain
Colony Count
Results
Bacteria
Bacillus Subtilis
Pseudomonas Aeruginosa
Staphlococcus Aureus
Enterococcus Faecalis
Nocardia Asteroides
6633
27317
25923
19433
31531
6.0 Log 7
1.5 Log 8
1.2 Log 8
1.2 Log 8
1.0 Log 8
No Growth
No Growth
No Growth
No Growth
No Growth
Fungi
Candida Albicans
Aspergillus Fumigatus
14053
1022
1.2 Log 8
1.1 Log 8
No Growth
No Growth
Myco-bacteria
Mycobacterium Bovis
Mycobacterium Fortuitum
35737
35755
5.0 Log 7
5.0 Log 7
No Growth
No Growth
1.0 Log 3
No Growth
5.0 Log 7
Negative
Protozoa
Giardia Miura
Virus
Duck Hepatitis Stanford Univ.
Source: North American Laboratory / Stanford University
Page 23 of 27
SYSTEM PERFORMANCE
3 1 0,&52%,2/2,*,&$/7(67,1* 5(68/76&RQWG
The SANITEC MDU has also been tested and approved for use in treating pathogical waste
and for animal carcassess. MDUs owned and operated by SANITEC in California and North
Carolina are prcessing pathological wastes. Acceptance and approval for treatment of
pathological waste with SANITEC MDUs have been in practice in other areas such as New York
State, Texas, Oklahoma, Kansas, Brazil, the Philippines and others.
Of particular note is the testing performed by the State of North Carolina Department of
Agriculture specially for the pursoes of treating avain flu contaminated carcasses:
Page 24 of 27
SYSTEM PERFORMANCE
32
The SANITEC MDU processes infectious waste at temperatures hot enough to inactivate
microbiological organisms, but not to a level where harmful by-products are created. In devices
that operate at temperatures above the melting point of plastics, volatile organic compounds
(VOC) emissions are a concern. The MDU operates at tempertures far below this point and
therefore does not emit harmful air emissions. Actually, tests were performed on six different
SANITEC installations analysing air samples with a gas chromoatograph and mass
spectrometer for VOC and toxic organic compounds (TOC). Since the MDU is equipped with
ACF that could absorb organic emissions, the test was conducted without the ACF to prove that
the MDU does create emissions from processing. In each case, the MDUs performance was
outstanding with results reported below dectable limits (BDL) or far far below personal exposure
limits (PEL):
Page 25 of 27
SYSTEM PERFORMANCE
32
Treated waste from SANITEC MDUs has been managed and disposed as ordinary soild waste
in every location installed in the US and around the world. Following is a representative analysis
performed on treated waste exiting a MDU:
Cadmium
Lead
Barium
Silver
Chromium
Arsenic
Selenium
Mercury
1.0
5.0
100
5.0
5.0
5.0
1.0
0.2
Test Result
< 0.015
0.11
0.99
<0.03
< 0.005
< 0.0054
0.034
< 0.0002
Combustibility
Moisture
Ash & Noncombustibiles
25-94
7.7-10.0
4.9-15.0
88.01(1)
5.04-14
6.95(2)
Notes:
(1)
(2)
33
The SANITEC MDU does not discharge any liquid waste. The MDU does not have a need for a
sewer connection.
Page 26 of 27
SYSTEM PERFORMANCE
33
The microwave generators used in the SANITEC MDU have been tested for safety and leakage,
and conform to US regulations governed by the Federal Communications Commission (FCC).
The magnatrons used in the MDU are manufacturered within strict tolerances regulated by the
FCC, and UL tested in the same manner as magnatrons used for consumer household
microwave ovens.
The OSHA permissable exposure limit is 10 mW/cm2, which is magnitudes greater than any
levels measureed in an MDU. Our leakage standard is ZERO. Our manual recommeds perodic
testing using a handheld leakage detection meter. If any leakage is detected, the user must only
tighten the flange bolts on the MWG mounting to the microwave chamber. We recommend that
2
this flange tightening check be performed routinely or when a leakage of 0.4 mW/cm
is
detected. With over 15 years of operating experience, the MDU design has been proven safe.
-------------------------------------------------------------------------------------------With over 15 years of a commercial operating track record, SANITEC MDU have never
been shutdown or taken out of service for failure to meet treatment or environmental
standards and requirements. Some MDUs have been in operation for more 15 years with
the same designed and features that have been described in this document.
001-818-504-6977
[email protected]
or visit Sanitec at
www.sanitecind.com
Page 27 of 27