Diodes and Their Applications: IV.1. The PN Junction (Diode)
Diodes and Their Applications: IV.1. The PN Junction (Diode)
Chapter IV
Diodes and their Applications
An important mindset of practical engineers is to build systems from simple and reliable components while
maximizing functionality and performance with a minimal number of basic devices. Diodes are among those
building blocks that are frequently part of electrically circuits. They are simple two-terminal devices which
conditionally pass current in one direction. Despite their simplistic nature, you can find them in diverse electrical
systems where they play key roles in power conversion, temperature measurements, protection of circuits from
excessive voltages, logic operations, and radiation detection. There are many other applications for diodes,
especially for those with special properties such as laser diodes used in optical communication systems. In this
chapter, you will learn about the basic properties of conventional diodes and how to exploit those properties to
construct various circuits with different functions.
IV.1. The PN junction (diode).
A PN junction diode is manufactured as semiconductor device, in which p-type and n-type semiconductor materials
(e.g. silicon) are joined together as visualized in Figure 4.1a. Current flow across the boundary between the two
types of semiconductor materials depends on the voltage applied at the two terminals called anode and cathode by
convention. This labeling convention also applies to the diode symbol shown in Figure 4.1b. The PN diode is a
unidirectional device with two modes of operation: The first one is referred to as forward biased, which is when
current can flow through the device and its intrinsic resistance is small. The second mode of operation is called
reverse biased. Under reverse bias conditions, the current flowing through the device is extremely small (less than
0.1 nA for most of the diodes in microelectronics applications), and the diode can be regarded as an open circuit.
In the forward bias region, the current flowing through the device depends on the voltage applied across the diode
terminals. This voltage-dependent current can be determined from the following approximation:
nVvd
Vvd
th
id I S e 1 I S e th 1 ,
(4.1)
where IS is the saturation current, Vth is the thermal voltage, and n is the diode constant. Here and throughout this
chapter it is assumed that n 1, as is the case for many silicon diodes. Since n depends on the diodes material and
the fabrication procedure used by the manufacturer, it is one of numerous reasons for you to consult the datasheet
before using a specific diode in the lab. The saturation current IS is a function of diode dimensions and other
physical parameters. Its value is strongly affected by temperature variations, typically ranging in the order of 10-10 10-15 A. The value of IS usually increases by factor of two when the temperature increases by 10 degrees. The
thermal voltage Vth is also temperature-dependent as can be observed from its definition:
Vth
kT ,
q
(4.2)
where k is the Boltzmann constant (=1.3810-23 J/K); T is the temperature in Kelvin degrees (300 K = 27
centigrade), and q is the fundamental charge of the electron (=1.610-19 C). At room temperature (300 K), the
thermal voltage Vth is roughly 26 mV. A diodes typical i-v curve is plotted in Figure 4.1c.
id
10 mA
id
p-type n-type
1 A
+ vd anode
cathode
anode
cathode
-IS
0.5
0.8
vd
(a)
(b)
(c)
Fig. 4.1. (a) Physical representation of a semiconductor diode, (b) the symbol for a diode, (c) typical id-vd curve.
1
Since the i-v curve is obtained by sweeping the dc voltage across the diode at DC or very low frequencies, none of
the diodes high-frequency limitations are captured in this plot. Hence, the i-v plot is known as the diodes DC
characteristics. For negative voltages, the diode behaves like a very large resistor by allowing a current flow around
-IS (less than -1 nA in most cases). Such a small current is negligible in most practical cases. For instance, if -1 V is
applied to the diodes terminals, then the current flowing through it is around IS. If IS = 0.1 nA, the diodes
equivalent resistance is in the order of rdiode = 1V/0.1 nA=1010, which can be treated like an open circuit.
A diode can be used for the processing of AC signals as well. The example circuit shown in Figure 4.2 operates as
an AC rectifier if the amplitude of the input signal is larger than 0V in the simplified diode model discussed here. It
can be described by the following equations:
vi v0
v0 id RL I S RL e VTH 1 if
v0 I S RL 0
if
vi 0
(4.3)
vi 0
id
vi
vo
0V
0V
RL
Fig. 4.2. A signal rectifier circuit with a diode.
Notice in equation 4.3 that the resulting output voltage is non-linear and there is no closed form solution for the
circuits operation, even if we try solve it for the two separate cases vi > 0 and vi < 0. Computer-based methods are
often used for plotting the output voltage as function of the input voltage. Even if the solution can be found for this
simple case, practical circuits might contain more diodes, making the solutions for the sets of non-linear equations
quite complex. Thus, many designers use a simpler model to quickly analyze and construct more complex systems
with diodes. This basic switch model is explained next.
IV.2. Simple switch model.
In a first approximation, the diode can be considered as a switch: if current is flowing from anode to cathode, then it
can be regarded as a short circuit (vd = 0); otherwise, it is treated like an open circuit (id = 0) and current cannot flow
through it. A simple model of this idealization is depicted in Figure 4.3.
operates in on condition, leading to the equivalent circuit shown in Figure 4.4a where the output voltage is vo = vi.
Therefore, the current flowing through the diode and resistor is id = vi/RL.
vo = 0
vo = vi
vi > 0
id
vi < 0
RL
id
RL
Fig. 4.4. Equivalent circuit for the two cases: (a) vi > 0, (b) vi < 0.
For the case vi < 0, the current, if any, should flow from vo to vi to ground; that is in the diodes reverse direction.
Due to the diodes characteristic, the reverse current is very small and assumed to be zero in the ideal model. The
diode is represented as an open circuit as shown in Figure 4.4b. Since id = 0, the voltage drop across the resistor is
zero and consequently the output voltage is zero. Since only the positive output voltage appears at the output of the
circuit and the output is zero during the negative half of the sinusoidal input signal in Figure 4.2, this topology is
known as a half-wave rectifier circuit.
The negative half rectifier circuit can be obtained by flipping the diode, as shown in Figure 4.5. When the input
signal is negative, the current flows from vo to vi to ground. Hence the diode operates in forward bias when vi < 0.
The diode behaves as a short circuit, leading to vi and to vo, where vo = vi. During the positive input cycle, the current
should flow from input to output, which is in the diodes reverse direction. This very small current is neglected in
the ideal model, leading to zero output voltage since id = 0.
analysis approach with the diode assumed to be in off condition is not valid. Since it is not always possible to
predict the bias conditions of the diodes when beginning to analyze a circuit, the chances are high to make false
assumption after which you have to analyze the circuit again while changing one or more diodes from an open
circuit to a short circuit or vice versa. Fortunately the probability of making the correct assumption on the first
attempt will increase as you analyze more circuits.
If the diode is flipped in the example circuit as shown in Figure 4.6b, a good initial guess is to consider the diode to
be turned off and replacing it with an open circuit. As a result, the load consists of a simple 1k resistor, leading
to an output voltage of 10 V. Applying the same check, the cathode is connected to a 10 V node and the anode is
connected to a 0V node since the open circuit prevents current flow through R2. With the new diode orientation and
analysis in off state, its terminal voltages give vd2 = 0 V - 10 V = -10 V < 0. This verification result agrees with
the reverse bias condition, indicating that the flipped diode in this circuit is in fact in off state according to the
ideal switch model. By analyzing the circuit again, you can prove to yourself that the diode in Figure 4.6b cannot be
on because the terminal voltages would violate the condition required for forward bias.
(a)
(b)
Figure 4.6. Current driven circuit with (a) forward biased diode and (b) with reverse biased diode.
The circuits shown in Figure 4.7 are two examples of voltage driven circuits. Notice that the current flows from the
positive 10V voltage source down to the ground terminal. In Figure 4.7a, the current flows through the diode in the
forward direction, hence the ideal diodes voltage drop is zero. Furthermore, the output current is limited to iout = 0
because the voltage-drop across the resistor in parallel with the diode is zero. The voltage drop and current flowing
through the upper resistor of 1k are 10 V and 10 mA, respectively. The diodes current is also 10 mA.
10V
10V
1 k
iout
1 k
iout
1 k
1 k
(a)
(b)
Fig. 4.7. Voltage driven circuit with (a) forward biased diode and (b) with reverse biased diode.
The diode in the circuit of Fig. 4.7b is connected in the reverse biased direction. Since current cannot flow through
the diode, it can be considered as an open circuit. Therefore, the current flowing through both resistors is the same,
and it can be computed as iout = 10V / 2k = 5mA. With the diodes anode being at 0V (grounded) and its cathode at
5 V, the voltage measured across its terminals is +5 V.
IV.3. A more accurate diode model.
A rudimentary but more accurate model takes the voltage drop across the diode terminals into account. As can be
observed in Figure 4.8, the diodes voltage drop is current-dependent and has to be computed using the diode
equation. However, the forward voltage drop across the diode is usually in the range of 0.5-0.8 V. Although it is still
an approximate approach, the results are typically closer to the actual values when a voltage drop of 0.7 V is
assumed for forward-biased diodes in hand calculations. This more accurate model is depicted in Figure 4.8, in
which the red line indicates the approximate current-voltage relationship. If the diodes current is positive, then the
diode is modeled by a fixed DC voltage source of 0.7 V. Be aware that other voltage drops such as 0.65 V are often
assumed or specified in different textbooks and datasheets because this property varies among component
manufacturers. As a rule of thumb, the diode voltage drop can be approximated as 0.65 V when small DC currents
(< 1mA) flow through it, as 0.7 V when 1 mA < id < 10 mA, and as 0.8 V when id > 10 mA.
10V
ix
iout
1 k
1 k
+
0.7V
-
Fig. 4.9. Circuit with the 0.7 V constant voltage source model for the forward biased diode.
A diode characteristic that has been ignored up to this point is the breakdown that occurs under large reverse bias
voltage, which is labeled as breakdown voltage in Figure 4.10. Due to the large current in the breakdown region,
conventional semiconductor diodes typically experience permanent damage under this condition. Even though it
often takes 50-150 V for the diodes to break down, you should always refer to the manufacturers datasheet if you
anticipate reverse voltage drops in your design. A special type of diode that is applied in some voltage regulators
and reference circuits is called a Zener diode, for which the symbol in Figure 4.11 is widely used. Zener diodes have
almost identical forward bias characteristics as the previously described conventional diodes, but they are fabricated
to ensure a controlled breakdown voltage as well as safe operation in the breakdown region. For silicon Zener
diodes, the voltage drop under reverse breakdown is usually below 10V, making it possible to create stable reference
voltages for a wide range of currents in the reverse direction.
id
+ vd cathode
anode
Figure 4.11. Symbol for a Zener diode that can be operated in breakdown region.
Although useful, the previous models do not consider the fact that the diodes voltage is a function of its current. A
more accurate model should consider this fact. The simplest model that is used for this purpose is based on the
combination of the DC battery and a series resistor, as depicted in Figure 4.12. The question that arises now is how
to compute resistor value rd.
id
IDQ
id
0.7V
VDQ
vd
vd
+ 0.7V -
rd
vd
Figure 4.12. More accurate diode model with a battery and a series resistor.
To analyze the issue of the rd calculation, let us consider the diode equation (4.1) repeated below for convenience.
Vvd
id I S e th 1
(4.4)
In Figure 4.12, the non-liner diode equation is approximated by a piece-wise linear function composed of two
straight lines such that
i)
id = 0 if vd 0.7V,
ii)
id = (vd - 0.7V) / rd if vd > 0.7V.
Notice in Figure 4.12 that the actual value of the current (equation 4.4) and the one resulting from the piecewise
linear model are the same at the point Q, which is usually termed as the operating point. The Q point is defined by
IDQ and VDQ (the diodes current and voltage evaluated at the operating point), and it is selected based on the
application and the characterization conditions of your device. Since the current-voltage diode relationship is nonlinear, it can be expanded in a Taylor series around the proper operation point (Q) as follows:
Vvd
iD I S e th 1 id
id
1 2id
id
1 2id
2
2
id
i
...
id ...
d
DQ
d
2
2
vd Q
2 vd Q
vd Q
2 vd Q
(4.5a)
The first component in this series is the DC (constant) current component that defines the operating point Q. The
second component measures the variation of the current when small voltage variations are applied, since id/vd|Q
represents the slope of the curve at the operating point Q. In the previous equation, it is assumed that the diodes
current IDQ is much larger than IS. This approximation is reasonable since IS < 1nA for most of the diodes. Due to the
higher order derivatives, expression 4.5a is very accurate but difficult to manipulate in complex circuits. In many
applications the signal applied to the diode is small (vd < Vth). Hence, the higher order terms can be ignored, leading
to the approximated but linear model of the diode:
iD I DQ
id
id I DQ g mid ,
vd Q
(4.5b)
where gm is known as the small-signal transconductance of the diode. This is the most popular diode model for
small-signal modeling. Notice that small-signal diode applications imply voltage variations around a DC value of no
more than 26mV. According to equation 4.5, you should understand very well how to compute the two fundamental
parameters: given a time-invariant DC voltage VDQ, you must find IDQ (also time-invariant) using equation 4.4. If the
diode is operated around the Q-point determined by VDQ and IDQ, the slope of the curve at Q determines gm, which
you can calculate by differentiating equation 4.4, rearranging the result, and making the appropriate substitutions:
gm
id
vd
Vvd
I S e th 1 I S
I I
I
Q
1
DQ S DQ
.
Vth
Vth
Vth rd
Vvd
vd
I S e th 1
Vth
ISe
vd
Vth
(4.6)
Q
Q
Manipulating equation 4.6 leads to the following formula for the computation of diodes AC resistance:
rd
V
1
th .
g m I DQ
(4.7)
Solving circuits with diodes usually involves two or three iterations before we arrive at a reasonable result. For
instance, let us reconsider the half-wave rectifier described in the previous section. Assuming that a sinusoidal input
signal with a peak value of 10 V and a load resistor RL = 10 k are used in the circuit of Figure 4.2, the output
signal for the three discussed diode models can be computed as follows. These three cases are plotted in Figure 4.13.
i) Ideal switch model: The diode is ON during the positive half-cycle, and the output voltage follows the input;
where the outputs peak value is 10 V as depicted in the trace labeled ideal rectifier that is shown in Figure
4.11. The peak diodes current is then equal to 1 mA. During the negative half-cycle, the diode is OFF and does
not conduct current, resulting in a 0 V output voltage.
ii) Constant voltage drop model: When the input signal is greater than 0.7V, the diode is ON and the voltage drop
across it is approximately 0.7 Volts. The output peak value is therefore equal to 9.3 Volts. Under these
7
conditions, the diodes peak current is computed as 0.93 mA. The conditions and output voltage during the
negative half-cycle are identical as with the constant voltage drop model in i).
iii) Model with diode resistance and constant voltage drop: In this case, the diodes current must be computed
before the output voltage can be computed. For intuitive insights, let us first make an incorrect assumption by
ignoring that the diodes peak current is affected by the series resistor. Then, from the peak current in case ii)
and equation 4.7, the diodes resistance would be rd = 26 mV / 0.93 mA = 28. With this first order
approximation, a more accurate peak current value can be computed as Ipk = 9.3V / 10.028k = 0.927 mA,
which is relatively close to the previous value. Next, the voltage drop across the resistor can be calculated as
28 0.927mA = 26mV. Thus, the output peaks value becomes Vout-pk = 10V - 0.7V - 0.026V = 9.274 V. In
comparison to the 9.3 V obtained in ii), this result is more accurate since it contains the resistors effect.
Depending on the accuracy requirements of the application, this value could still have a significant error
because the diode voltage drop is not considered a small-signal voltage (vd > Vth 26 mV). Also notice that we
substituted the peak current into equation 4.7 instead of the quiescent current IDQ. With large voltage and
current variations, the resistance rd actually varies dynamically as a function of the diode current during the
positive half-cycle, which is not taken into account here. Nevertheless, this approximation is more accurate than
the other two cases and it is typically sufficient for hand calculations to select initial design parameters for
circuit components prior to simulations.
Fig. 4.13. Half-wave rectifier and its output voltage illustrating the differences between the three diode models.
Notice that the previous circuit is able to extract the peak value of the signal. However, if glitches are present in the
system, the peak value might not be the real information of interest. Hence, some losses can be included on purpose
to partially discharge the capacitor, providing a more robust solution at the expense of reduced accuracy. The circuit
in Figure 4.15 includes a resistor to introduce such a loss. As before, the diode is on when the value of the input
signal increases beyond the previously stored output voltage such that the output follows the input. Assuming an
ideal diode, the equation for the output voltage in Figure 4.15 is
v out v in
t1 T t t 0 .
for
(4.8)
At the time t = t0, vin = Vpeak. After this time, the input signal decreases, but the output voltage is partially sustained
by the capacitor. Hence, the diode is reverse biased and operating as an open circuit. Since the diode is off when t0 <
t < t1, the capacitor is discharged through the load resistor RL. During this time period, the output voltage is
determined by the first order differential equation iCL + iRL = CL(dVout/dt) + Vout/RL = 0, whose solution is given by
the following expression
vout V peak e
t t0
RL C L
if
t0 t t1 .
(4.9)
Important parameters to be determined are t1 - t0 and the voltage ripple Vripple = Vpeak - vout(t1), where the output
voltage ripple (Vripple) is a quality indicator for AC-to-DC converters. The smaller the ripple, the better is the
converters efficiency. Likewise, a small ripple voltage improves the accuracy when the circuit serves as a peak
detector. To facilitate the calculations, let us assume that our time scale is such that t0 = 0. The output signal reaches
the peak value at t = t0 = 0 and it decreases until the input signal increases to the point that the following condition is
met for the sinusoidal input signal and the output voltage according to equation 4.9:
Fig. 4.15. AC-to-DC converter using a half-wave rectifier. This circuit is also known as peak/envelope detector with
resistive losses, which was frequently used in old FM radio demodulators.
t
V peak cos0 t1 V peak cos 2 1 V peak e
T
t1
RL C L
(4.10)
Finding the solution of the previous equation at t = t1 is not trivial since it is a non-linear equation. One option would
be to solve it using numerical methods. A simple and useful alternative solution is obtained if we assume that the
ripple is small, hence t1 T. An easy way to find an approximate solution is by expanding the exponential function
in a Taylor series
t
1
RL C L
t 1 t
1 1 1 ....
RLCL 2 RLCL
(4.11)
If the resistor and capacitor are selected such that t1, T << 1/RLCL, the higher order terms can be neglected and the
output voltage can be approximated as
vout t V peak e
t
RL C L
t
V peak .
1
R
C
L
L
(4.12)
If t1 T, then the normalized ripple voltage (Vpeak - vout)/ Vpeak can be determined by evaluating equation 4.12 at
Vpeak = vout(t = t0 = 0) and vout(t = t1 T):
Vripple %
V peak vout t t1 T
V peak
T
T
,
RLCL
(4.13)
where T is the period of the input signal and RLCL = is the circuits time constant. To decrease the ripple, we
should increase as much as possible. Potential drawbacks are the associated increases of component size and
cost.Equation 4.13 is very simple and can give you a clear indication on how to design an AC-to-DC converter with
small ripple. Just select the resistor and capacitor component values to ensure that the T/ratio is less than the ripple
specification. For instance, a 10% ripple limit requires that T/< 0.1.
IV.5. Full-wave rectifiers.
To reduce the ripple of the rectified output voltage, a transformer is typically combined with diodes to achieve fullwave rectification. The classic full-wave rectifier without output filter is shown in Figure 4.16. A center-tapped
transformer is employed to generate fully-differential output signals that are rectified by the diodes. To understand
the operation of the circuit, let us assume that the voltage on the secondary side of the transformer is such that the
voltage at the upper terminal is positive while the voltage at the bottom terminal is negative. Under these conditions,
the upper diode is ON and the lower diode is OFF, as labeled in Figure 4.16. The positive signal is then transferred
to the output, leading to a peak output voltage equal to the peak value of the secondary terminal of the transformer
minus the 0.7V voltage drop across the forward-biased diode. The operation repeats during the following half cycle,
but now the bottom diode is ON while the top diode is OFF. If the circuit is not capacitively loaded, the output will
be a rectified version of the input signal. In AC-to-DC conversion applications, the advantage of a full-wave rectifier
is its better conversion efficiency compared to a half-wave rectifier. This is explained by the fact that both the
positive and negative half-cycles of the input are rectified with a full-wave rectifier, resulting in a higher RMS
output voltage.
ON OFF
Vpk
125V
60 Hz
Vpk - 0.7V
+
vin
-
+
v
Load out
-
Vpk
OFF ON
10
Fig. 4.17. Full-wave rectifier with a center-tapped transformer and filter capacitor CL.
Vripple %
V peak vout t t1 T / 2
V peak
T
T
.
2 RL C L 2
(4.14)
Evidently, the ripple of the output from the full-wave rectifier is half of that from the half-wave rectifier. This is a
major benefit of this circuit, and it is often a good reason to invest in a center-tapped transformer and two diodes.
However, if the transformer is not fully balanced such that the peak voltage of both outputs is the same, then the
output ripple will increase. Since it is not easy to maintain a good output balance for center-tapped transformers, the
circuit displayed in Figure 4.18 can be utilized to overcome this drawback because it includes a transformer without
center tap. This structure is a full-wave rectifier with an array of four diodes such that two diodes are ON and two
are OFF depending on the polarity of the input signal. The capacitor CL minimizes the output ripple as discussed
previously. Since this is a full-wave rectifier, the ripple should be calculated with equation 4.14.
Fig. 4.18. AC-to-DC converter based on a full-wave rectifier that is comprised of a transformer without center tap.
To get insights into the operation of the circuit, let us to remove the capacitor and analyze the simplified version of
the rectifier depicted in Figure 4.19. During the positive half-cycle, the voltage at the upper transformer terminal is
positive. Consequently, diodes D1 and D4 are ON and OFF, respectively. Since the voltage at the transformers
bottom terminal is negative, D2 and D3 are ON and OFF, respectively, which leads to the equivalent circuit depicted
in Figure 4.20.
11
D1 and D2 are ON
D4
125V
60 Hz
vin
vin
D1
D3 and D4 are ON
- vout +
RL
D2
D3
Fig. 4.20. Equivalent circuit for the full-wave rectifier during the positive half-cycle.
Figure 4.21 presents a conceptual diagram for a typical AC-to-DC converter. The actual circuit-level
implementation of the rectifier might be more complex than the architectures described in this chapter, but the
fundamental principles remain the same. Similarly, the low-pass filter and voltage regulator circuits could be very
complex for demanding applications. The design of these circuits is outside of the scope in this introductory book,
but you will encounter these types of circuits if you are going to work in the power generation or power
management fields.
12
between two bodies at different potentials. You have probably experienced such an event many times while touching
a door knob after walking on carpet. ESD incidents are very likely to occur during the manufacturing and lifetime of
a chip whose pins come into contact with equipment and sometimes humans. To protect the chip from large
damaging voltages, a pair of diodes can be inserted at input and output pins. Here, the additional protection circuitry
at the positive supply (VDD) and negative supply (VSS) pins is not included in Figure 4.22 for simplicity. If
undesirable voltage spikes from ESD events appear at the input or output pins, then the discharging current flows
through D1 and D3 when the spike is larger than VDD + 0.7V, given that the diodes have a forward voltage drop of
0.7V. Likewise, diodes D2 and D4 prevent that the discharging current flows into the internal circuits when the
spikes voltage is below VSS 0.7V. The VSS pin is grounded in this example, thus D2 and D4 will turn on if the
voltage at the respective pins falls below -0.7V. An additional consideration with protection diodes is that the signal
must now remain within VDD + 0.7V and VSS 0.7V as visualized in Figure 4.22. Otherwise, one of the diodes at the
input/output will turn on and clamp the signal, which leads to signal loss and distortion (clipped signals).
VDD
Chip
ESD
Spikes
D3
D1
Internal
Circuits
In
Out
VDD + 0.7V
safe range
D4
D2
VSS - 0.7V
Vss
(a)
(b)
Fig. 4.23. A simple voltage reference circuit: (a) without load, (b) with resistive load.
Figure 4.23a presents a voltage reference circuit consisting of two stacked diodes and one resistor. From the
equivalent circuit in the same figure, we can express the output voltage as Vo = 2 0.7V + iD (rd1 + rd2). Since the
output is not loaded by any circuit elements, we know that the current iD is equal to iR. Furthermore, iD flows
through both diodes, implying that rd = rd1 = rd2 can be substituted in the output voltage equation as well. With these
simplifications, we can write Vo = 2 ( 0.7V + iD rd ) for the unloaded case. To approximate the value of rd, we
assume that Vo is around 1.4V. It follows that iR = iD (6V 1.4V) / RD = 2.3 mA, and that rd Vth / iD = 11.3 at
room temperature (Vth 26mV). Now, the actual output voltage can be calculated as Vo = 2 ( 0.7V + 2.3mA
13
11.3 ) = 1.452 V. For a more accurate result, you could repeat the calculation of Vo with iR = (6V 1.452V) / RD =
2.274 mA and the corresponding new value of rd, but the first iteration is often sufficient in these hand calculations.
The circuit at the output of a reference generator has a finite input impedance that is high in the ideal case, but it
could be in the same order of magnitude as resistor RD. This raises an important question in practical scenarios:
What will happen to the output voltage Vo if a resistor RL of 10 k for instance is connected to the reference
generator under investigation as shown in Figure 4.23b? First of all, you can observe that iL Vo / RL = 1.45V /
10k = 0.145 mA in the first order small-signal approximation. From Kirchoffs current law you can also derive
that the new current through the diodes is iD = iR iL = 2.3mA 0.145 mA = 2.155 mA. Therefore, the diode current
change due to the loading effect is iD = 2.155 mA 2.3mA = -0.145 mA. Since the associated change of the
voltage drop across the two series diode resistances directly affects the output voltage, the loading effect of RL is
Vo 2rd iD = -3.3mV. The change in DC (average) load voltage as the load conditions vary is one important
metric to assess the quality of voltage regulates or reference circuits. This measure of quality is called load
regulation, and it is often defined as a percentage:
Vunloaded Vloaded
100% .
Vunloaded
(4.15)
When providing a load regulation specification based on equation 4.15, it is a proper practice to report the load
conditions in terms of current or impedance for the loaded case as well as the permissible load current or impedance
range. If the load range is not specified, then you should assume that the given load is the full load, i.e. the
maximum allowed current or minimum allowed resistance. Since the supply voltage VDD always has small or large
fluctuations due to noise sources in the real world, another important measure of quality for a voltage
regulator/reference is its line regulation. As an exercise, you can calculate the output voltage change for the example
circuit in Figure 4.23a by changing VDD to 6.2V for example. In general, the line regulation is typically defined as:
Vo
100% .
VDD
(4.16)
We have already identified that load and supply voltage variations cause deviations from the desired output voltage.
Other sources of variations and inaccuracies are the tolerance of the resistor RD, the effect of temperature on the
diode characteristics, and the modeling error from using a small-signal approximation for the diode resistance rd as
well as assuming a fixed 0.7V diode voltage drop. When designing circuits, you should always consult datasheets
and equipment manuals to assess the anticipated variations through hand calculations and simulations. The
appropriate design margins and circuit specifications are normally based on thorough evaluations in the design and
testing phases during the product development. For example, if you would like to estimate how much the output
voltage in the unloaded reference circuit (Figure 4.23a) can vary when you use a resistor with a 10% tolerance
specification, you can quickly do so by calculating the resulting minimum and maximum currents: iD(min) (6V
1.45V) / (1.1RD) = 2.07 mA, iD(max) (6V 1.45V) / (0.9RD) = 2.53 mA. Substituting these currents into the
equation for the output voltage without load gives: Vo(min) = 2 ( 0.7V + iD(min) rd ) = 1.447 V, Vo(min) = 2 ( 0.7V
+ iD(min) rd ) = 1.457 V. The roughly 10mV output voltage difference might be significant since voltage reference
often have to meet stringent accuracy requirements. You can repeat the calculations to find out how much the output
voltage change is reduced when a precision resistor with 0.5% is available, and to check the impact of resistor
variation in the loaded case.
14