ATC Apr 10
ATC Apr 10
PART B
1. (i) Enumerate various ATC aids.
Ans:
The following are the various ATC aids:
1. Radio and Navigation Aids
2. Airport Lighting Aids (ALS)
3. Airport Visual Aids
4. Air Navigation and Obstruction Lighting Aids
5. Airport Marking Aids and Signs
6. Fitness for Flight
7. Flight Safety
8. Emergency services
(ii) Briefly discuss the various parts of ATC services
Ans:
Air Traffic Control services: A generic term meaning area control service, approach
control service or aerodrome control service. The air traffic services comprise of three services
identified as follows:
1. Air traffic control service
Area control service
Approach control service
Aerodrome control service
2. Flight information service
3. Alerting service
Area Control Service:
The provision of air traffic control service for controlled flights, except for those parts of
such flights which are under the jurisdiction of Approach Control or Aerodrome Control to
accomplish following objectives:
a) Prevent collisions between aircraft
b) Expedite and maintain an orderly flow of air traffic
Approach control service:
The provision of air traffic control service for those parts of controlled flights associated
with arrival or departure.
Aerodrome control service:
The provision of air traffic control service for aerodrome traffic, except for those parts of
flights which are under the jurisdiction Approach Control.
Provision of air traffic control service:
The parts of air traffic control service, shall be provided by the various units as follows:
Area control service
Area control service shall be provided:
a) By an area control centre (ACC); or
b) By the unit providing approach control service in a control zone or in a control
area of limited extent which is designated primarily for the provision of approach control
service, when no ACC is established
Approach control service
Approach control service shall be provided:
a) By an aerodrome control tower or an ACC, when it is necessary or desirable to
combine under the responsibility of one unit the functions of the approach control service and
those of the aerodrome control service or the area control Service.
b) By an approach control unit, when it is established as a separate unit.
Not all airports have a radar approach or terminal control available. In this case, the en-route
center or a neighboring terminal or approach control may co-ordinate directly with the tower on the
airport and vector inbound aircraft to a position from where they can land visually. At some of
these airports, the tower may provide a non-radar procedural approach service to arriving aircraft
handed over from a radar unit before they are visual to land. Some units also have a dedicated
approach unit which can provide the procedural approach service either all the time or for any
periods of radar outage for any reason
2. Write short notes on:
(i) Area control service (6)
Ans:
Area control service: Air Traffic Control service for controlled flights in control areas.
In air traffic control, an Area Control Center (ACC), also known as a Center, is a facility
responsible for controlling instrument flight rules aircraft en route in a particular volume of
airspace (a Flight Information Region) at high altitudes between airport approaches and departures.
- A Center typically accepts traffic from, and ultimately passes traffic to, the
control of a Terminal Control Center or of another Center.
- Most Centers are operated by the national governments of the countries in
which they are located.
- The general operations of Centers worldwide, and the boundaries of the
airspace each Center controls, are governed by the ICAO
The provision of air traffic control service for controlled flights, except for those parts of
such flights which are under the jurisdiction of Approach Control or Aerodrome Control to
accomplish following objectives:
a) Prevent collisions between aircraft;
b) Expedite and maintain an orderly flow of air traffic;
Area control service shall be provided:
a) By an area control centre (ACC); or
b) By the unit providing approach control service in a control zone or in a control area of
limited extent which is designated primarily for the provision of approach control service, when no
ACC is established.
En-route air traffic controllers work in facilities called Area Control Centers, each of which
is commonly referred to as a "Center". The United States uses the equivalent term Air Route Traffic
Control Center (ARTCC). Each center is responsible for many thousands of square miles of
airspace (known as a Flight Information Region) and for the airports within that airspace. Centers
control IFR aircraft from the time they depart from an airport or terminal area's airspace to the time
they arrive at another airport or terminal area's airspace. Centers may also "pick up" VFR aircraft
that are already airborne and integrate them into the IFR system. These aircraft must, however,
remain VFR until the Center provides a clearance.
Center controllers are responsible for climbing the aircraft to their requested altitude while,
at the same time, ensuring that the aircraft is properly separated from all other aircraft in the
immediate area. Additionally, the aircraft must be placed in a flow consistent with the aircraft's
route of flight.
As an aircraft reaches the boundary of a Center's control area it is "handed off" or "handed
over" to the next Area Control Center. In some cases this "hand-off" process involves a transfer of
identification and details between controllers so that air traffic control services can be provided in a
seamless manner; in other cases local agreements may allow "silent handovers" such that the
receiving center does not require any co-ordination if traffic is presented in an agreed manner. After
the hand-off, the aircraft is given a frequency change and begins talking to the next controller. This
process continues until the aircraft is handed off to a terminal controller ("approach").
Alternate aerodrome(s)
Endurance
Persons on board
Survival equipment
Pilot in command
Other information
If a flight is to cross a Finish state border, details of the entire flight to the destination
aerodrome shall be submitted in the flight plan.
3. (i) Describe the procedure for the design of aerodrome. (8)
Ans:
Instrument approach procedures are designed to enable pilots to operate under Instrument
Flight Rules (IFR) in Instrument Meteorological Conditions (IMC). The instrument approach
procedures may direct aircraft to either descend down to circling minima and conduct a visual
circling approach, or to a runway aligned position down to the runway landing minima and conduct
a straight-in approach.
Where the instrument approach procedure does not provide a straight-in approach, the
runway is still classified as a non-instrument runway. Where the instrument procedure provides for
a straight-in approach, the runway is classified as an instrument non-precision approach (NPA)
runway.
CASA strongly recommends that, where terrain permits, NPA procedures be provided as
they enhance the safety and efficiency of aircraft operations. NPA procedures may use groundbased navigation aids, such as VOR, DME, NDB, etc. Increasingly, NPA procedures may also be
designed using GPS. The use of GPS allows NPA procedures to be provided to aerodromes which
have no access to ground-based navigation aids.
Before a GPS NPA procedure is designed and published for a particular runway, the runway
must meet the standards of a NPA runway. At some aerodromes there may be a cost involved in
meeting these aerodrome standards. Whilst it is the prerogative of an aerodrome operator to
determine whether his or her aerodrome should be upgraded, CASA strongly recommends that
aerodrome operators avail themselves of the benefit of GPS technology.
Request for NPA procedures may come from the Regional Airspace Planning and Advisory
Committee (RAPAC), airline operators, aviation organizations, or aerodrome operators.
Any proposal for, and design of, instrument approach procedures to a runway should only
be made with the knowledge that the runway meets the appropriate aerodrome standards for NPA.
Use of a runway which does not meet the appropriate aerodrome standards for NPA procedures
could result in unsafe situations.
Aerodrome standards: The standards for a NPA runway are different to the standards
applicable to a non instrument runway in several aspects. These include:
Runway strip width
`
Approach OLS area and gradient
Availability of wind direction indicator near the threshold
Runway edge light spacing
RUNWAY STRIP WIDTH:
Many existing aerodromes have runways of 30 metres width contained within runway strips
90m to 150m wide. NPA procedures may be designed for runways with strip widths down to 90m
provided the landing minima is adjusted in accordance with design requirements. The 90m strip
width for NPA procedures are limited only to runways used by code 1, code 2 and up to code 3C
aero planes. (Runways accommodating aero planes above code 3C (eg. B737) require a minimum
graded runway strip width of 150m).
At aerodromes where NPA operations are conducted, aerodrome operators should ensure
that time limited works are co-ordinated with arrival schedules to avoid risk to aircraft and persons
on the ground.
Currently, development works are being done in the global navigation satellite system
(GNSS) with local or wide area augmentation to enhance the accuracy of the system. It is likely
that in the near future Cat I precision approaches will be able to be conducted to runways with no
Instrument Landing System (ILS).
The aerodrome standards will need to be met to support these operations are more stringent,
particularly in regard to runway and approach lighting. Aerodrome operators should bear this in
mind if they are considering upgrading their aerodrome lighting systems.
GPS NPA procedures may also be provided for helicopter landing sites (HLS), either on or
off aerodromes. Currently, Australian standards do not specify NPA standards for HLS. In the
interim, HLS meeting the NPA standards specified in ICAO Annex 14 Volume II are acceptable.
(ii) How are aerodrome classified in India. (8)
Ans:
Airports Classification:
In order to provide guide to airport designers for a reasonable amount of uniformity in
airport landing facilities, design criteria have been prepared by ICAO and FAA through airport
classifications.
Aerodrome in India:
With so many airports in India, traveling has become really convenient and easy. Over all
these years, the Indian air industry has grown several folds and contributed in a big way to the
tourism industry in India. Today there are a large number of airlines in India which have made it
convenient for the travelers to reach their destinations easily. Most of the airports in India connect
the Indian cities with the International cities. These are the international airports in India. The
domestic airports in India link all the major corners of the country.
Airports Authority of India (AAI)
This Airports Authority of India which is under the control of Ministry of Civil Aviation is
in charge of managing all the airports in India. The AAI is involved in the management and
operation of 126 airports in India which include:
11 international airports
89 domestic airports
26 civil enclaves
Classification of Airports in India
India has a total of 449 airports, out of which 92 airports and 28 civil enclaves in Defence
airports offer flight services over the entire airspace of India and the neighboring oceanic areas.
However, only 61 airports out of the total are permitted to be utilized by the airlines.
The Indian airports are categorized into following classifications:
Indian airports are divided into 3 broad categories
* Domestic
* International and
*Civil enclave
There are two more categories in India
* Customs Airport
* Model Airport
International Airports in India: These are declared as international airports and are
available for scheduled international operations by Indian and foreign carriers. Presently,
Mumbai, Delhi, Chennai, Calcutta and Thiruvananthapuram are in this category.
The following airports link the major Indian cities to the international cities:
Amritsar International Airport , Indira Gandhi International Airport, New Delhi, Lokpriya
Gopinath Bordolio International Airport, Guwahati, Sardar Vallabhbhai Patel International
Airport, Ahmedabad, etc.,
Domestic Airports in India: All the Indian airports come under this category.
Custom Airports in India: Custom Airports provide immigration and customs facilities for
the international tourists. They also operate cargo charter flights. The custom airports in India
are located at: Bangalore, Hyderabad, Ahmedabad, Calicut, Cochin, Goa, Varanasi, Patna,
Agra, Jaipur, Amritsar, Tiruchirapally
Model Airports in India: Indian Model Airports are the domestic airports with following
features:
Minimum 7500 feet length of runway
Sufficient terminal capacity for handling aircraft of Airbus 320 type
If required, can also handle limited international traffic
The model airports in India are located in: Lucknow, Bhubaneshwar, Guwahati, Nagpur,
Vadodara, Coimbatore, Imphal, Indore
Civil Enclaves in Indian Defence Airports: 28 civil enclaves are included in the Defence
airfields of India.
4. Briefly discuss the various requirements of an airport lighting systems and airport
marking systems.
Ans:
Refer Question No. 14 and 16 in Part B Ques and Ans.
5. Draw the typical layout of a small domestics terminal building and typical airport layout.
Explain any two.
Ans:
The layout of an airport is determined by five basic factors:
- The direction of prevailing winds (the major runways being oriented to the
prevailing wind with a back up runway on a cross wind alignment)
- The size and number of terminal buildings
- The ground transport system, especially the position of major access roads and
railways
- Mandatory clearance dimensions between aircraft and buildings
- Topography and geology
Small airports are usually a direct reflection of these spatial and organizational
characteristics but as airports become larger a number of secondary factors come into play such as
environmental controls, the geography of the surrounding region, and the capacity of the local road
system. International airports, though their site layout is shaped primarily by wind direction, are
increasingly constrained by such factors as community disturbance. As a consequence their growth
and configuration rarely permit simple planning solution but are compromised by influences of a
regional nature.
Airport Types:
There are three main types of airport:
- International airports serving over 20 million passengers a year
- National airports serving between 2 and 20 million passengers a year
- Regional airports serving up to 2 million passengers a year
Such a classification, based upon the level of traffic flow is a useful guide but by no means
infallible. In countries such as Germany, which have a strong hub network of airports, some of the
larger regional airports have passenger movements that approach international dimensions.
Conversely in smaller countries with single national airports passenger movement below the norm
for the classification may justify the inclusion of the airport in the top rank. If the level of
passengers is a good is good general guide, other factors relevant to typological classification
include:
Fig: Typical design of a terminal building: showing the Departures (upper half of
page) and Arrivals levels. 1. Departures Lounge. 2. Gates and jet bridges. 3. Security Clearance
Gates. 4 Baggage Check-in. 5. Baggage Carousels
Terminal Building:
An airport terminal is a building at an airport where passengers transfer between ground
transportation and the facilities that allow them to board and disembark from aircraft.
Within the terminal, passengers purchase tickets, transfer their luggage, and go through
security. The buildings that provide access to the airplanes (via gates) are typically called
concourses. However, the terms "terminal" and "concourse" are sometimes used interchangeably,
depending on the configuration of the airport.
Smaller airports have one terminal while larger airports have several terminals and/or
concourses. At small airports, the single terminal building typically serves all of the functions of a
terminal and a concourse.
Some larger airports have one terminal that is connected to multiple concourses via
walkways, sky-bridges, or underground tunnels. Some larger airports have more than one terminal,
each with one or more concourses. Still other larger airports have multiple terminals each of which
incorporates the functions of a concourse.
Airport Terminal Concept:
The terminals at small airports have mostly been designed as centralized building that is
where the processing of the passengers is done in one location rather than being distributed through
several points in the terminal. The concept of the centralized terminal in combination wither piers,
fingers or satellites is also used at larger airports. It provides easy orientation for the passengers
through check in and security, optimum utilization of space and concentration of services in the
terminal building. However, as the number of stands increases, the distance to the outlying stands
exceeds the recommended walking distances and therefore it is necessary to provide transportation
for the passengers from the central processing building to the gates together with an effective
information system. A central building with a system of several parallel satellite piers
interconnected by a transportation system makes an almost ideal solution for large airports if the
space is available midfield ie., between parallel runways. It has a large capacity of both stands and
peak hour passengers. It enables transfer of passengers to and from common travel areas without
using the central building which then not required to handle these passengers. Therefore this design
is convenient for the hub and spoke type of operation. It seems that it is possible to use central
processing terminals up to about 30 mppa and 50or so gates, whether they have piers and moving
walkways or have satellites and people movers.
6. (i) What are the ATC clearance requirements for airport (8)
Ans:
ATC clearance is an authorization for an aircraft to proceed under conditions specified by
an air traffic control unit. Clearance may be prefixed by the words taxi, take off, departure,
en-route, approach or landing to indicate the particular portion of flight to which the air
traffic control clearance relates.
ATC clearances normally required to contain the following:
a. Clearance Limit: The traffic clearance issued prior to departure will normally authorize
flight to the airport of intended landing. Many airports and associated NAVAIDs are collocated
with the same name and/or identifier, so care should be exercised to ensure a clear
understanding of the clearance limit. When the clearance limit is the airport of intended landing,
the clearance should contain the airport name followed by the word airport. Under certain
conditions, a clearance limit may be a NAVAID or other fix. When the clearance limit is a
NAVAID, intersection, or waypoint and the type is known, the clearance should contain type.
Under certain conditions, at some locations a short-range clearance procedure is utilized
whereby a clearance is issued to a fix within or just outside of the terminal area and pilots is
advised of the frequency on which they will receive the long-range clearance direct from the
center controller.
b. Departure Procedure: Headings to fly and altitude restrictions may be issued to
separate a departure from other air traffic in the terminal area. Where the volume of traffic
warrants, DPs have been developed.
c. Route of Flight:
1. Clearances are normally issued for the altitude or flight level and route filed by
the pilot. However, due to traffic conditions, it is frequently necessary for ATC to specify an
altitude or flight level or route different from that requested by the pilot. In addition, flow
patterns have been established in certain congested areas or between congested areas whereby
traffic capacity is increased by routing all traffic on preferred routes. Information on these flow
patterns is available in offices where preflight briefing is furnished or where flight plans are
accepted.
2. When required, air traffic clearances include data to assist pilots in identifying
radio reporting points. It is the responsibility of pilots to notify ATC immediately if their radio
equipment cannot receive the type of signals they must utilize to comply with their clearance.
d. Altitude Data:
1. The altitude or flight level instructions in an ATC clearance normally require that
a pilot MAINTAIN the altitude or flight level at which the flight will operate when in
controlled airspace. Altitude or flight level changes while en route should be requested prior to
the time the change is desired.
2. When possible, if the altitude assigned is different from the altitude requested by
the pilot, ATC will inform the pilot when to expect climb or descent clearance or to request
altitude change from another facility. If this has not been received prior to crossing the
boundary of the ATC facility's area and assignment at a different altitude is still desired, the
pilot should reinitiate the request with the next facility.
3. The term cruise may be used instead of MAINTAIN to assign a block of
airspace to a pilot from the minimum IFR altitude up to and including the altitude specified in
the cruise clearance. The pilot may level off at any intermediate altitude within this block of
airspace. Climb/descent within the block is to be made at the discretion of the pilot. However,
once the pilot starts descent and verbally reports leaving an altitude in the block, the pilot may
not return to that altitude without additional ATC clearance.
e. Holding Instructions:
1. Whenever an aircraft has been cleared to a fix other than the destination airport
and delay is expected, it is the responsibility of the ATC controller to issue complete holding
instructions (unless the pattern is charted), an EFC time, and a best estimate of any additional
en route/terminal delay.
2. If the holding pattern is charted and the controller doesn't issue complete holding
instructions, the pilot is expected to hold as depicted on the appropriate chart. When the pattern
is charted, the controller may omit all holding instructions except the charted holding direction
and the statements ASPUBLISHED, e.g., HOLD EAST AS PUBLISHED. Controllers must
always issue complete holding instructions when pilots request them.
3. If no holding pattern is charted and holding instructions have not been issued, the
pilot should ask ATC for holding instructions prior to reaching the fix. This procedure will
eliminate the possibility of an aircraft entering a holding pattern other than that desired by ATC.
If unable to obtain holding instructions prior to reaching the fix (due to frequency congestion,
stuck microphone, etc.), hold in a standard pattern on the course on which you approached the
fix and request further clearance as soon as possible. In this event, the altitude/flight level of the
aircraft at the clearance limit will be protected so that separation will be provided as required.
4. When an aircraft is 3 minutes or less from a clearance limit and a clearance
beyond the fix has not been received, the pilot is expected to start a speed reduction so that the
aircraft will cross the fix, initially, at or below the maximum holding airspeed.
5. When no delay is expected, the controller should issue a clearance beyond the fix
as soon as possible and, whenever possible, at least 5 minutes before the aircraft reaches the
clearance limit.
6. Pilots should report to ATC the time and altitude/flight level at which the aircraft
reaches the clearance limit and report leaving the clearance limit.
(ii) Mention the approximate obstruction clearances requirements of the current airports.
(8)
Ans:
Air traffic is responsible for obstacle clearance when issuing a descend via instruction to
the pilot. The descend via is used in conjunction with STARs/RNAV STARs/FMSPs to reduce
phraseology by not requiring the controller to restate the altitude at the next waypoint/fix to
which the pilot has been cleared.
The ILS glide slope is intended to be intercepted at the published glide slope intercept
altitude. This point marks the PFAF and is depicted by the lightning bolt symbol onU.S.
Government charts. Intercepting the glide slope atthis altitude marks the beginning of the final
approachsegment and ensures required obstacle clearance during descent from the glide slope
intercept altitude to the lowest published decision altitude for theapproach.
Terminal Arrival Area (TAA): The TAA provides the pilot and air traffic controller with a
very efficient method for routing traffic into the terminal environment with little required air
traffic control interface, and with minimum altitudes depicted that provide standard obstacle
clearance compatible with the instrument procedure associated with it.
Minimum MSL altitudes are charted within each of these defined areas/subdivisions that
provide at least 1,000 feet of obstacle clearance, or more as necessary in mountainous areas.
Where lower minimum vectoring altitude (MVAs) are required in designated mountainous
areas to achieve compatibility with terminal routes or to permit vectoring to an IAP, 1,000feet
of obstacle clearance may be authorized with the use of Airport Surveillance Radar (ASR).
The minimum vectoring altitude will provide at least 300 feet above the floor of controlled
airspace.
Visual Segment of a Published Instrument Approach Procedure: Instrument procedures
designers perform a visual area obstruction evaluation off the approach end of each runway
authorized for instrument landing, straight-in, or circling. Since missed approach obstacle
clearance is assured only if the missed approach is commenced at the published MAP or above
the DA/MDA, the pilot should have preplanned climb out options based on aircraft
performance and terrain features. Obstacle clearance is the sole responsibility of the pilot when
the approach is continued beyond the MAP.
Vertical Descent Angle (VDA) on Non-precision Approaches: The pilot must determine
how to best maneuver the aircraft within the circling obstacle clearance area in order to land.
Pilot Operational Considerations When Flying Non-precision Approaches: Pilots must be
especially vigilant when descending below the MDA at locations without VDPs. This does not
necessarily prevent flying the normal angle; it only means that obstacle clearance in the visual
segment could be less and greater care should be exercised in looking for obstacles in the visual
segment.
ILS or RNAV (GPS) charts: Some RNAV (GPS) charts will also contain an ILS line of
minima to make use of the ILS precision final in conjunction with the RNAV GPS capabilities
for the portions of the procedure prior to the final approach segment and for the missed
approach. Obstacle clearance for the portions of the procedure other than the final approach
segment is still based on GPS criteria.
Obstacle clearance is provided to allow a momentary descent below Decision Altitude
(DA) while transitioning from the final approach to the missed approach. The aircraft is
expected to follow the missed instructions while continuing along the published final approach
course to at least the published runway threshold waypoint or MAP (if not at the threshold)
before executing any turns.
Descent to the procedure turn (PT) completion altitude from the PT fix altitude (when
one has been published or assigned by ATC) must not begin until crossing over the PT fix or
abeam and proceeding outbound. Some procedures contain a note in the chart profile view that
says Maintain (altitude) or above until established outbound for procedure turn. Newer
procedures will simply depict an at or above altitude at the PT fix without a chart note. Both
are there to ensure required obstacle clearance is provided in the procedure turn entry zone.
Obstacle Clearance:
Final approach obstacle clearance is provided from the start of the final segment to the
runway or missed approach point, whichever occurs last. Side-step obstacle protection is
provided by increasing the width of the final approach obstacle clearance area.
Circling approach protected areas are defined by the tangential connection of arcs drawn
from each runway end. The arc radii distance differs by aircraft approach category (see FIG 54-26). Because of obstacles near the airport, a portion of the circling area may be restricted by a
procedural note: e.g., Circling NA E of RWY 17-35. Obstacle clearance is provided at the
published minimums (MDA) for the pilot who makes a straight-in approach, side-steps, or
circles. Once below the MDA the pilot must see and avoid obstacles. Executing the missed
approach after starting to maneuver usually places the aircraft beyond the MAP. The aircraft is
clear of obstacles when at or above the MDA while inside the circling area, but simply joining
the missed approach ground track from the circling maneuver may not provide vertical obstacle
clearance once the aircraft exits the circling area. Additional climb inside the circling area may
be required before joining the missed approach track. Missed Approach, for additional
considerations when starting a missed approach at other than the MAP.
Precision Obstacle Free Zone (POFZ): A volume of airspace above an area beginning at
the runway threshold, at the threshold elevation, and centered on the extended runway
centerline. The POFZ is 200 feet (60m) long and 800 feet (240m) wide. The POFZ must be
clear when an aircraft on a vertically guided final approach is within 2 nautical miles of the
runway threshold and the reported ceiling is below 250 feet or visibility less than 3/4 statute
mile (SM) (or runway visual range below 4,000 feet). If the POFZ is not clear, the MINIMUM
authorized height above touchdown (HAT) and visibility is 250feet and 3/4 SM. The POFZ is
considered clear even if the wing of the aircraft holding on a taxiway waiting for runway
clearance penetrates the POFZ; however, neither the fuselage nor the tail may infringe on the
POFZ. The POFZ is applicable at all runway ends including displaced thresholds.
Circling Minimums: In some busy terminal areas, ATC may not allow circling and circling
minimums will not be published. Published circling minimums provide obstacle clearance when
pilots remain within the appropriate area of protection. Pilots should remain at or above the
circling altitude until the aircraft is continuously in a position from which a descent to a landing
on the intended runway can be made at a normal rate of descent using normal maneuvers.
Circling may require maneuvers at low altitude, at low airspeed, and in marginal weather
conditions. Pilots must use sound judgment, have an in-depth knowledge of their capabilities,
and fully understand the aircraft performance to determine the exact circling maneuver since
weather, unique airport design, and the aircraft position, altitude, and airspeed must all be
considered.
The published missed approach procedure provides obstacle clearance only when the
missed approach is conducted on the missed approach segment from or above the missed
approach point, and assumes a climb rate of 200 feet/NM or higher, as published.
7. (i) Explain the four elements of the RADAR control and non RADAR control with the
help of a neat sketch. (8)
Ans:
Refer Question No. 20 in Part B Ques and Ans.
(ii) An option is given either to improve an existing airport on to develop a new airport.
What will be the governing considerations?
(8)
Ans:
Increase of airport and airspace capacity
Increase of airport and airspace
capacity ACI POLICY
1. ACI believes that technical and
operational means should be
developed to improve airport and
airspace capacity at existing
facilities, as well as the building of
new capacity
ACI supports closer cooperation
with ANSPs to develop better
8. Write in detail on air transportation in India with special references to the civil aviation
department
Ans:
Aerodrome Reference Code or Special References to Civil Aviation means a code used for
planning purposes to classify an aerodrome with respect to the critical aircraft characteristics for
which the aerodrome is intended;
AERODROME FACILITY REFERENCE CODE:
1 The aerodrome facility reference code, also to be known as the aerodrome reference
code, is a two-element, alpha-numeric notation (for example 1B, 3C) derived from the critical
aeroplane for that aerodrome facility. The code number is based on the aeroplane reference field
length and the code letter is based on the aeroplane wing span and the outer main gear wheel span.
As detailed below, a single element may sometimes suffice.
2 The aerodrome reference code provides a method of grouping aeroplanes with different
characteristics (eg. wing span, outer main gear wheel span, approach speed and all-up mass) which
behave similarly when landing, taking-off or taxying. This, in turn, enables standards for aerodrome
facilities such as runways to be set in terms of a small number of aeroplane groups, rather than
individually for a large number of separate aeroplanes. The task of the standard setting authority
and of the aerodrome operator is thus simplified.
3 As the aerodrome reference code notation is derived from aeroplane and not aerodrome
characteristics, it applies to the individual aerodrome facilities (eg, runways and taxiways) and
indicate their suitability for use by specific groups of aeroplanes. Thus at the same aerodrome there
may exist, for example, a code 4E runway, a code 1A runway, a code C taxiway and a code 2
runway strip ( a single element sufficing in the latter case).
4 In many cases to determine the appropriate design standard for an aerodrome facility, it
is necessary first to identify the aeroplanes for which the facility is intended, and then to determine
the aerodrome reference code notation for the most critical of these aeroplanes. The particular
standard for the facility is then related to the more demanding of the two criteria (the number or the
letter) or to an appropriate combination of both.
5 The code number for the critical aeroplane is to be determined from Table 71 by
entering the aeroplane reference field length and reading off the corresponding code number.
6 The code letter for an aeroplane is to be obtained from Table 72 by deriving the code
letter applicable to the wing span, and separately deriving the code letter applicable to the outer
main gear wheel span. The code letter to be used is the more senior of these letters where A is the
junior.
7 The general dimensions, of a typical aeroplane, are shown in the diagrams below.
table below (sample only). For a particular aeroplane the table also provides data on the aeroplane
reference field length (ARFL), wing span and outer main gear wheel span used in determining the
aerodrome reference code. For aerodrome planning purposes, data is also provided on the overall
aeroplane length, maximum take-off weight and tyre pressure of main wheel tyres. It should be noted
that the data provided is indicative only, for instance, factors such as engine type or flap settings can
result in a different aeroplane reference field length. Exact values of a particular aeroplanes
performance characteristics should be obtained from information published by the aeroplane
manufacturer
conditions changed while flying, the ground had no way to warn them. A pilot, too, had no way of
communicating with the ground.
The Aeronautics Branch stepped up installation of four-course radio ranges, and this
technology became standard for civil air navigation through World War II.
Pilot to use only aircraft instrument guidance to take off, fly a set course, and land. He used
the four-course radio range and radio marker beacons to indicate his distance from the runway. An
altimeter displayed his altitude, and a directional gyroscope with artificial horizon helped him
control his aircraft's orientation, called attitude, without seeing the ground. These technologies
became the basis for many future developments in navigation.
First ultrahigh-frequency radio range system for scheduled airline navigation, eventually
expanding use of such equipment.
Advances in radio very high frequency (VHF) omni-directional radio range (VOR) that
allowed pilots to navigate by watching a dial on their instrument panel rather than by listening to
the radio signal.
The FAA began using distance-measuring equipment on its entire system. This equipment
allowed aircraft to determine their distance from known checkpoints in order to confirm their
position. The first Doppler radar version of the VOR system made it more accurate for longer
distances.
The FAA participated with the National Aeronautics and Space Administration in the first
public demonstration of a new system in March 1967 that would use orbiting satellites to transmit
navigation data from aircraft to ground stations. The test was followed by further development of
aircraft antennas to send and receive satellite messages.
In October 1969, 16 area navigation routes were developed. Previously, pilots had flown
directly toward or away from the ground-based radio navigation aid (a VOR or VORTAC). This
aid transmitted a course along invisible lines called radials. With area navigation, pilots could fly
any pre-selected flight path roughly within the boundaries of that local system while an onboard
computer tracked and reported the aircraft's position. Courses could be established along the
shortest path within these route segments.
Navigation aids, the computers supporting the system, and cockpit displays and instruments
to send and receive navigation data all improved steadily.
Additional navigation technologies are in partial use or development, including the Global
Positioning System both to locate and help control aircraft by satellite, the Future Air Navigation
System for remote and oceanic flights, and the Communication, Navigation and Surveillance for
Air Traffic Management system. These technologies combine the need for point-to-point
navigation and for higher quality voice and data communication with the need for air traffic
control--the safe separation of aircraft from hazards and other aircraft.
Terminal aids: an airfield equipped with control tower and hangars as well as
accommodations for passengers and cargo. An airport (terminal) is a location where aircraft such as
fixed-wing aircraft, helicopters, and blimps take off and land. Aircraft may be stored or maintained
at an airport. An airport consists of at least one surface such as a runway for a plane to take off and
land, a helipad, or water for takeoffs and landings, and often includes buildings such as control
towers, hangars and terminal buildings.
Area Control Centres (ACCs): Area Control Centres provide air traffic control,
information services and alerting services for aircraft within a designated area. ACCs normally
divide their assigned airspace into sectors that are controlled by a controller or team of controllers.
Control services are provided through a combination of radar, information technology,
voice communication and highly skilled personel applying strict and proven separation criteria and
procedures; to ensure safe, consistent separation and orderly, efficient flow of traffic from origin to
destination. NAV CANADA operates 7 Area Control Centres in Gander, Moncton, Montreal,
Toronto, Winnipeg, Edmonton, and Vancouver.
Air Traffic Control Towers (ATCs) : Air Traffic Controllers working in Control Towers
provide pilots approaching and departing busy airports with clearances and instructions to ensure
their aircraft have sufficient separation (horizontal, lateral, and vertical distance from each other).
Tower controllers also provide flight information to aircraft operating within designated
airspace around their airports. At busier airports monitoring of ground movements is enhanced
through ground surveillance radar systems. NAV CANADA operates 41 control towers across the
country.
Flight Service Stations (FSSs): Flight Service Stations (FSS) provide resources for flight
planning, access to briefings on weather and other preflight information, aeronautical information,
enroute and airport advisory services, vehicle control services, monitoring of navaids, VHF/DF
assistance and alerting of Search and Rescue centres for overdue aircraft. NAV CANADA has 58
Flight Service Stations.
Flight Information Centres (FICs): FICs centralize the provision of those flight
information services that are not location dependent, providing pilots with efficient, seamless flight
planning, enroute services and better access to flight information services. They are a one-stop shop
for flight planning and in-depth interpretive weather briefings provided by qualified specialists,
using the latest computer and communications technology. Services are offered pre-flight and en
route.
Aerodrome Radio Stations (ARS): Aerodrome Radio Stations provide aviation weather and
communications services at designated sites. These facilities are equipped with meteorological
instruments for monitoring and recording aviation surface weather, and communications equipment
for providing operational information to pilots. They are operated by observers/communicators who
are usually recruited locally.
Remote Communications Outlets (RCOs) and Remote Aerodrome Advisory Services
(RAAS): Remote Communications Outlets are remote transmitters/receivers set up to extend the
communications capabilities of FSS stations. They allow Flight Service Specialists to provide some
flight information services to remote areas and aerodromes without a staffed NAV CANADA
facility. When an RCO is used to provide airport advisory services at a remote aerodrome, the
service is referred to as a Remote Aerodrome Advisory Service (RAAS).
Landing and Navigational Aids: Landing Aids and Related Facilities directly support
aircraft and assist during departure, en-route, and arrival. The Instrument Landing System (ILS) is
the primary international precision approach system approved by ICAO. It provides navigational
guidance signals and information on a cockpit display which guides pilots to the point of landing in
reduced visibility.
Radio Navigation Facilities: Radio Navigation Facilities are installed on defined flight
tracks for use in the enroute phase of flight, or at aerodromes where they can be used to perform
non-precision approaches under IFR conditions. Normally two or more types of Navigational Aids
(NAVAIDS) are co-located at a site to provide a combination of functions and to ensure reliability.
Non-directional radio beacons (NDB) transmit on a low frequency a non-directional radiation
pattern. Distance Measuring Equipment (DME) responds to aircraft queries to provide cockpit
display of the distance to the DME facility from a suitably equipped aircraft. VHF OmniDirectional Range/Distance Measuring Equipment is a ground-based, short-distance radio aid
which provides continuous azimuth information in the form of 360 usable radials TO or FROM a
station. It serves as the basis for most of the civil airways structure. The Tactical Air Navigation
System is used to define the azimuth lines between the aircraft and the transmitter, and also the
distance from the aircraft to the transmitter. TACAN is supplied by the military and operated and
maintained.
RAMP Radar Site Equipment - The air navigation system uses radar surveillance for both
terminal and enroute control.
Airport Surface Detection Equipment (ASDE) At six airports surface aircraft and
vehicle traffic is monitored during periods of reduced visibility through the use of Airport Surface
Detection Equipment (ASDE) radar.
bar VASI installations provide one visual glide path which is normally set at 3. The 3-bar system
provides two glide paths; the lower glidepath normally set at 3 and the upper glidepath degree
above the lower glide path.
The basic principle of the VASI is that of color differentiation between red and white. Each
light unit projects a beam of light, a white segment in the upper part of the beam and a red segment
in the lower part of the beam. The lights are arranged so the pilot sees the combination of lights to
indicate below, on, or above the glide path.
Other Glide path Systems
A precision approach path indicator (PAPI) uses lights similar to the VASI system except
they are installed in a single row, normally on the left side of the runway. A tri-color system
consists of a single light unit projecting a three-color visual approach path. Below the glidepath is
indicated by red, on the glidepath is indicated by green, and above the glidepath is indicated by
amber. When descending below the glidepath, there is a small area of dark amber. Pilots should not
mistake this area for an above the glidepath indication.
Pulsating visual approach slope indicators normally consist of a single light unit projecting
a two-color visual approach path into the final approach area of the runway upon which the
indicator is installed. The on glidepath indication is a steady white light. The slightly below
glidepath indication is a steady red light. If the aircraft descends further below the glidepath, the red
light starts to pulsate. The above glidepath indication is a pulsating white light. The pulsating rate
increases as the aircraft gets further above or below the desired glide slope
Obstruction Lights
Obstructions are marked or lighted to warn pilots of their presence during daytime and
nighttime conditions. Obstruction lighting can be found both on and off an airport to identify
obstructions.
Wind Direction Indicators
It is important for a pilot to know the direction of the wind. At facilities with an operating
control tower, this information is provided by ATC. Information may also be provided by FSS
personnel located at a particular airport or by requesting information on a CTAF at airports that
have the capacity to receive and broadcast on this frequency.
Traffic Patterns
At those airports without an operating control tower, a segmented circle visual indicator
system if installed is designed to provide traffic pattern information. Usually located in a position
affording maximum visibility to pilots in the air and on the ground and providing a centralized
location for other elements of the system, the segmented circle consists of the following
components: wind direction indicators, landing direction indicators, landing strip indicators, and
traffic pattern indicators.
The use of one of the external aids (e.g., a kneepad) can reduce the demands of Air Traffic
Control (ATC) communication on pilots working memory during routine flight. The use of two
external aids that may vary in ease of coordination: a conventional knee pad and an electronic
notepad, or e-pad.
Internal Aids:
Radio Communications
Operating in and out of a towered airport, as well as in a good portion of the airspace
system, requires that an aircraft have two-way radio communication capability. For this reason, a
pilot should be knowledgeable of radio station license requirements and radio communications
equipment and procedures
ATC Radar Beacon System (ATCRBS)
The ATC radar beacon system (ATCRBS) is often referred to as secondary surveillance
radar. This system consists of three components and helps in alleviating some of the limitations
associated with primary radar. The three components are an interrogator, transponder, and
radarscope. The advantages of ATCRBS are the reinforcement of radar targets, rapid target
identification, and a unique display of selected codes.
Transponder
The transponder is the airborne portion of the secondary surveillance radar system and a system
with which a pilot should be familiar. The ATCRBS cannot display the secondary information
unless an aircraft is equipped with a transponder. A transponder is also required to operate in
certain controlled airspace as discussed in Chapter 14, Airspace.
10. Calculate the actual length of the runway from the following data:
Airport Elevation
RL 100
Airport reference temperature
28 deg C
Basic length of runway
1600 m
Highest part along the length
RL 98.2
Lowest part along the length
RL 95.2
Ans:
Refer the answer in Air Transportation and Planning by virendra kumar