GREENHOUSE CULTIVATION-english
GREENHOUSE CULTIVATION-english
GREENHOUSE CULTIVATION-english
b) Medium-tech greenhouse
Greenhouse users prefers to have manually or semiautomatic control
arrangement owing to minimum investment. This type of greenhouse is
constructed using galvanized iron (G.I) pipes. The canopy cover is attached with
structure with the help of screws. Whole structure is firmly fixed with the ground
to withstand the disturbance against wind. Exhaust fans with thermostat are
provided to control the temperature. Evaporative cooling pads and misting
arrangements are also made to maintain a favourable humidity inside the
greenhouse. As these system are semi-automatic, hence, require a lot of
attention and care, and it is very difficult and cumbersome to maintain uniform
environment throughout the cropping period. These greenhouses are suitable for
dry and composite climatic zones.
c) Hi-tech greenhouse
To overcome some of the difficulties in medium-tech greenhouse, a hi-tech
greenhouse where the entire device, controlling the environment parameters,
are supported to function automatically.
Cost involved
1.
Rs.300 to 500/m2
2.
Medium cost greenhouse with pad and fan system
Rs.1100/m2
Rs.800 to
without automation
3.
Expensive greenhouses with fully automatic
Rs.3500/m2
Rs.2000 to
control system
Other classifications
The greenhouse can also be classified based on type of structures, type of
glazing, number of spans, environmental control etc. The various types are as
follows.
Poly house
The crops grown in open field are exposed to vivid environmental conditions,
attack of insects and pests, whereas the polyhouse provides a more stable
environment. Polyhouse can be divided in to two types
a) Naturally ventilated polyhouse
These polyhouse do not have any environmental control system except for the
provision of adequate ventilation and fogger system to prevent basically the
damage from weather aberrations and other natural agents..
Shade house
Shadehouses are used for the production of plants in warm climates or during
summer months. Nurserymen use these structures for the growth of hydrangeas
and azaleas during the summer months. Apart from nursery, flowers and foliages
which require shade can also be grown in shadehouses. E.g. Orchids, These
shade structures make excellent holding areas for field-grown stock while it is
being prepared for shipping to retail outlets. Shadehouses are most often
constructed as a pole-supported structure and covered with either lath
(lathhouses) or polypropylene shade fabric. Polypropylene shadenets with
various percentages of ventilations are used. Black, green, and white coloured
nets are used, while black colours are the most preferred as it retains heat
outside.
Top
The design of greenhouse should be based upon sound scientific principles which
facilitates controlled environment for the plant growth. Controlled environment
plant production systems are used widely throughout the world to produce plant
materials and products at a time or place, or of a quality that can not be
obtained outdoors. Controlled environment agriculture requires far more capital
investment per unit area than field agriculture and thus must essentially be
correspondingly more intensive to justify investment costs. The greenhouse is a
structure covered with a transparent material for admitting natural light for plant
growth. The main components of greenhouse like structure, covering/glazing and
temperature control systems need proper design for healthy growth of plants.
Under Indian conditions, Quonset type, multispan greenhouse is most suitable,
because of its low cost and ease of fabrication. Ultra violet resistant low density
polyethylene (UVLDPE) single film cladding of 200 micron thickness is sufficient
for Naturally Ventilated ( NV) greenhouse and fan and pad (FP) greenhouses. This
should be fully tightened by stretching on the structure to avoid fluter and
tearing. It should not be nailed or screwed to the structure as it gives the chance
for tearing. The T-Lock of LLock should be used for fastening the sheet at
structure, as this does not tear the sheet and sheet replacement is easy.
Design
The structure has to carry the following loads and is to be designed accordingly.
a) Dead load: weight of all permanent construction, cladding, heating and cooling
equipment, water pipes and all fixed service equipments to the frame.
b) Live load: weights superimposed by use (include hanging baskets, shelves and
persons working on roof). The greenhouse has to be designed for a maximum of
15 kg per square meter live load. Each member of roof should be capable of
supporting 45 kg of concentrated load when applied at its centre.
c) Wind load: The structure should be able to withstand winds of 110 kilometer
per hour and at least 50 kg per square meter of wind pressure.
d) Snow load: These are to be taken as per the average snowfall of the location
The greenhouse should be able to take dead load plus live load or dead load
plus wind load plus half the live load.
The greenhouses are to be fabricated out of Galvanized Iron Pipes. The
foundation can be 60cmx60cmx60cm or 30 cm diameter and one meter depth in
PCC of 1:4:8 ratio. The vertical poles should also be covered to the height of 60
cm by PCC with a thickness of 5cm. This avoids the rusting of the poles.
Orientation
Orientation of the greenhouse is a compromise for wind direction, latitude of
location and type of temperature control. Single greenhouses with latitude above
40N should have ridge running east to west to allow low angle light to enter
from side rather than ends. Below 40N the ridge of single greenhouses should
be oriented from north to south, since the angle of sun is much higher. This
orientation permits the movement of shadow of the gutter across the green
house. The location and orientation of the greenhouse should avoid falling of
shadow on the adjacent greenhouses. To avoid the shading effect from one green
house to another greenhouse these should be oriented East to West. However,
the wind direction and latitude are also to be considered.
Wind effects
If the greenhouse is naturally ventilated, the advantage of natural wind direction
has to be taken to the maximum possible. The maximum dimension (length) of
greenhouse should be perpendicular to the wind direction especially in summer.
For fan and pad greenhouse the natural wind direction should be same as the air
blown by fan.
Height of greenhouse
The maximum height can be up to 5m for 50m x 50m green house and this can
be reduced as per the reduced size of the green house. Higher is the greenhouse
more is the wind load for structure and glazing. The side ventilation can be of 2
m width and roof ventilation is 1m in width.
Structural design
The greenhouses are to be designed for necessary safety, serviceability, general
structural integrity and suitability. The structure should be able to take all the
necessary dead, live, wind and snow loads. The foundation, columns and trusses
are to be designed accordingly. The greenhouse structures are to be designed to
take up the loads as per design loads prescribed by the National Greenhouse
Manufactures Association (NGMA of USA) standards 1994.
Top
3. Components of greenhouse
Cladding material: transparent material mounted on the walls and roof of a green
house.
Rigid cladding material: cladding material with such a degree of rigidity that any
deformation of the structure may result in damage to it. Ex. Glass
Flexible cladding material: cladding material with such a degree of flexibility that
any deformation of the structure will not result in damage to it. Ex. Plastic film
Gutter: collects and drains rain water and snow which is place at an elevated
level between two spans.
Green house length: dimension of the green house in the direction of gable
Green house width: dimension of the green house in the direction of the gutter
Cladding material
Polythene proves to be an economical cladding material. Now long lasting,
unbreakable and light roofing panels-UV stabilized clear fiber glass and
polycarbonate panels are available. Plastics are used in tropical and sub-tropical
areas compared to glass/fiberglass owing to their economical feasibility. Plastics
create enclosed ecosystems for plant growth. LDPE (low density polyethylene) /
LLDPE (linear low density polyethylene) will last for 3-4 years compared to
polythene without UV stabilizers.
Light
Heat
1.
Poly ethylene
One year
90%
70%
Very high
2.
Poly ethylene UV resistant
Two years
90%
70%
High
3.
Fiber Glass
Seven years
90%
5%
Low
4.
Tedlar coated Fiber Glass
Fifteen years
90%
5%
Low
5.
6.
Poly carbonate
Fifty years
90%
5%
Very low
Top
Clay pot
Low cost
Easy water management
Slow to work with pots and dry out fast
They are heavy to handle
Fiber block
Easy to handle
Slow root penetration
Short life
Fiber tray
Single peat
Pallet
No media preparation
Low storage requirement
Requires individual handling Limited sizes can be handled
Prespaced
Peat pallet
No media preparation
Limited to small sizes
Single peat
Good root penetration
Difficult to separate
Pot
Easy to handle in field Available (square / round) in large sizes
Protrays
Easy to handle Reusable
May be limited in sizes
Plastic pack
Easy to handle
Roots may grow out of container
Plastic pot
Reusable
Good root penetration
Requires handling as single plant
Polyurethane foam
Easy to handle Requires less medium Reusable
Requires regular fertilization
Soil band
Good root penetration
Requires extensive labour
Soil block
Excellent root penetration
Expensive machinery
Perforated
Easy to handle
Requires regular fertigation
Plastic tray
Requires less medium Available in many sizes reusable
Perforated
Less expensive
Less durable
Polyethylene
Reusable bags
Requires less storage space
Top
Plants need an optimum temperature for maximum yield and quality. The
greenhouses in plain and coastal region of India needs cooling. The greenhouses
in mild climates and coastal region can be naturally ventilated. The greenhouses
for hot summer climates of northern plains have to evaporatively cooled or with
fan and pad (FP). The greenhouses for northern plains may require both cooling
and heating depending on the crop.
Natural ventilation
The greenhouse has to be thoroughly ventilated for control of temperature. It
should be noticed that the temperature built up in the greenhouse is not
exceeding 2C throughout the year. Further during hot months the temperature
in the greenhouse was same as the ambient temperature.
Heating of greenhouse
The heating of greenhouses in cold climates like winter in North India or
Himalayan Region at high altitudes is advisable for getting better produce.
Double
covering of glazing with an air cushion of 2 cm to 10 cm reduces the heating
load
considerably.
Heating systems
These can be of the following types
a. Boiler
1. With hot water tube
2. With steam pipes
b. Unit heaters
c. Infrared heaters
d. Solar heaters
Boiler
This system is used for very big greenhouses and is a centralized system of
heating. The boiler of necessary capacity is provided in the greenhouse. The fuel
for boiler can be coal or fuel oil. The heating of the greenhouse is generally done
through hot water at 85C or steam at 102C. Water or steam pipes are installed
above the beds of crop and along the side wall. The steam system is cheaper
than hot water system. To reduce the length of pipe to be used a number of hot
water or steam pipe coils can be used and green house air circulated over them
by blower for heating.
Unit heaters
These are localized system of heating and a number of unit heaters are to be
provided in the greenhouse at a height of about 3 meter to distribute heat evenly
in the greenhouse. In a unit heater the fuel is combusted in the chamber at
bottom. Hot fumes rise inside the heat exchanger tubes, giving heat to the walls
of the tubes. Smoke exists at the top. A fan forces cool air of the greenhouse
over the outside of heat exchange tubes, where it picks up heat.
Infra-red heaters
The fuel gas (LPG) is burnt and the fumes at a temperature of about 480C are
passed in 10 cm diameter pipes kept overhead at a height of 1.5m above plants.
Reflectors are provided over the full length of pipe to radiate the infra red rays
over the plants. The plants and soil only get heated without much heating of air.
The infra red heating pipes can be provided at 6 to 10 meters interval all along
the length of greenhouse. The temperature of fume gases at exist is about 65C
and exhaust fan is provided for maintaining the flow of fumes.
Solar heating
Flat plate solar heaters are used to heat the water during day time. The hot
water is stored in the insulated tanks. The hot water is circulated in pipes
provided along the length of the greenhouse during night. Supplementary or
emergency heating systems are provided for heating the greenhouse during
cloudy or rainy days.
Environmental control
Temperature control
The thermostat can be coupled to water circulating pump or exhaust fan for
controlling the temperature inside the greenhouse. However, the lowest
achievable temperature in fan and pad greenhouse is not below the wet bulb
temperature in any case.
Quality of light
Quality of light refers to its wave-length composition. Light in the orange-red
portion of the visible spectrum from either sunlight or artificial illumination is
most effective in causing the long-day response in plants. Far-red radiation
appears to have the opposite effect. It is probable that the wave lengths activate
some hormonal mechanism within the plant which brings about the specific
effect of light on growth or flowering.
Design
The cross fluted cellulose pad is preferred. These are available mostly in 100mm
thickness. One meter of pad height is given for every 20m of pad to fan distance.
How ever, the fan to pad distance should not exceed 60m. The air flow rate
Maintenance of pad
The algae will grow and salts will deposit on pads if these are not maintained
properly. Good control of algae can be obtained without using chemicals by the
following methods.
1. By shading the pads and sumps
2. By drying the pads daily
3. By avoiding nutrient contamination
4. By draining and disinfecting the sump regularly
5. By replenishing 20% of circulating water each time to avoid scaling of
minerals.
Maintenance of fan
1. The lubrication of bearings should be done regularly
2. The v belt should be tightened as per requirement
3. The levers should be properly lubricated.
Top
Soil mixes used for greenhouse production of potted plants and cut flowers are
highly modified mixtures of soil, organic and inorganic materials. When top soil is
included as a portion of the mixture, it is generally combined with other
materials to improve the water holding capacity and aeration of the potting soil.
Many greenhouses do not use topsoil as an additive to the soil mixes, but rather
use a combination of these organic and inorganic components as an artificial soil
mix. When managed properly as to watering and fertilization practices, these
artificial mixes grow crops that are equal to those grown in top soil.
Medium which is too compact creates problems of drainage and aeration which
will lead to poor root growth and may harbour disease causing organisms.
Highly porous medium will have low water and nutrient holding capacity, affects
the plant growth and development.
The media reaction (pH of 5.0 to 7.0 and the soluble salt (EC) level of 0.4 to 1.4
dS/m is optimum for most of the greenhouse crops).
Gravel culture
Gravel culture is a general term which applies to the growing of plants with out
soil in an inert medium into which nutrient solutions are usually pumped
automatically at regular intervals. Haydite (shale and clay fused at high
temperatures), soft- or hard-coal cinders, limestone chips, calcareous gravel,
silica gravel, crushed granite and other inert and slowly decomposing materials
are included in the term gravel. The more important greenhouse flowering
crops include roses, carnations, chrysanthemums, gardenias, snapdragons, lilies,
asters, pansies, annual chrysanthemums, dahlias, bachelor buttons and others.
NO3
N
P
K
1.
Transplants
75
125
10-15
250-300
2.
Young pot & foliage plants
50
90
6-10
150-200
3.
Plants in beds
125
225
10-15
200-300
Heat
Steam
30 min at 180 F
Methyl bromide
10 ml/cu. ft. of medium
Cover with gas proof cover for 24-48 hr. Aerate for 24-28 hr before use.
Chloropicrin
(Tear gas) 3-5 ml/cu. ft. of medium
Cover for 1-3 days with gas proof cover after sprinkling with water. Aerate for 14
days or until no odour is detected before using.
Basamid
8.0 g/cu.ft. of medium
Cover for 7 days with gas proof cover and aerate for atleast a week before use.
Formalin
20 ml/l of water (37%)
Apply 2 l/cu.ft. cover for 14 to 36 hr and aerate for at least 14 days.
Captan
2 g/l of water
Pythium, Fusarium, Rhizoctonia and Phytophthora. Some extent to root and stem
rot, white mold,black rot, crown rot and damping off.
Fumigation in greenhouse
Physical propagation facilities such as the propagation room, containers, flats,
knives, working surface, benches etc. can be disinfected using one part of
formalin in fifty parts of water or one part sodium hypochlorite in nine parts of
water. An insecticide such as dichlorvos sprayed regularly will take care of the
insects present if any. Care should be taken to disinfect the seed or the planting
materials before they are moved into the greenhouse with a recommended seed
treatment chemical for seeds and a fungicide insecticide combination for
cuttings and plugs respectively. Disinfectant solution such as trisodium
phosphate or potassium permanganate placed at the entry of the greenhouse
would help to get rid off the pathogens from the personnel entering the
greenhouses.
Top
The plant is required to take up very large amounts of water and nutrients, with a
relatively small root system, and manufacture photosynthates for a large amount
of flower per unit area with a foliar system relatively small in relation to required
production.
Watering system
Micro irrigation system is the best for watering plants in a greenhouse. Micro
sprinklers or drip irrigation equipments can be used. Basically the watering
system should ensure that water does not fall on the leaves or flowers as it leads
to disease and scorching problems. In micro sprinkler system, water under high
pressure is forced through nozzles arranged on a supporting stand at about 1
feet height. This facilitates watering at the base level of the plants.
Filters: Depending upon the type of water, different kinds of filters can be used.
Gravel filter: Used for filtration of water obtained for open canals and reservoirs
that are contaminated by organic impurities, algae etc. The filtering is done by
beds of basalt or quartz.
Hydrocyclone: Used to filter well or river water that carries sand particles.
Screen filters: Stainless steel screen of 120 mesh ( 0.13mm) size. This is used for
second stage filtration of irrigation water.
Fertigation system
In fertigation system an automatic mixing and dispensing unit is installed which
consists of three systems pump and a supplying device. The fertilizers are
dissolved separately in tanks and are mixed in a given ratio and supplied to the
plants through drippers.
Fertilizers
Fertilizer dosage has to be dependent on growing media. Soilless mixes have
lower nutrient holding capacity and therefore require more frequent fertilizer
application. Essential elements are at their maximum availability in the pH range
of 5.5 to 6.5. In general Micro elements are more readily available at lower pH
ranges, while macro elements are more readily available at pH 6 and higher.
Liquid fertilizer
These are 100 per cent water soluble. These comes in powdered form. This can
be either single nutrient or complete fertilizer. They have to be dissolved in warm
water.
2. Intermittent application
Liquid fertilizer is applied in regular intervals of weekly, biweekly or even
monthly. The problem with this is wide variability in the availability of fertilizer in
the root zone. At the time of application, high concentration of fertilizer will be
available in the root zone and the plant immediately starts absorbing it. By the
time next application is made there will be low or non existent. This fluctuation
results in uneven plant growth rates, even stress and poor quality crop.
Fertilizer injectors
This device inject small amount of concentrated liquid fertilizer directly into the
water lines so that green house crops are fertilized with every watering.
Multiple injectors
Multiple injectors are necessary when incompatible fertilizers are to be used for
fertigation. Incompatible fertilizers when mixed together as concentrates form
solid precipitates. This would change nutrient content of the stock solution and
also would clog the siphon tube and injector. Multiple injectors would avoid this
problem. These injectors can be of computer controlled H.E. ANDERSON is one of
the popular multiple injector.
Fertilizer Injectors
Fertilizer injectors are of two basic types: Those that inject concentrated
fertilizer into water lines on the basis of the venturi principle and those that
inject using positive displacement
A. Venturi Principle Injectors
1.Basically these injectors work by means of a pressure difference between the
irrigation line and the fertilizer stock tank.
a) The most common example of this is the HOZON proportioner.
b) Low pressure, or a suction, is created at the faucet connection of the Hozon at
the suction tube opening. This draws up the fertilizer from the stock tank and is
blended in to the irrigation water flowing through the Hozon faucet connection.
c) The average ratio of Hozon proportioners is 1:16. However, Hozon
proportioners are not very precise as the ratio can vary widely depending on the
water pressure.
d) These injectors are inexpensive and are suitable for small areas. Large
amounts of fertilizer application would require huge stock tanks due to its narrow
ratio.
5. Dosatron feature variable ratios (1:50 to 1:500) and a plain water bypass.
6. Plus injectors also feature variable ratios (1:50 to 1:1000) and operates on
water pressure as low as 7 GPM.
7. Gewa injectors actually inject fertilizer into the irrigation lines by pressure.
a. The fertilizer is contained in a rubber bag inside the metal tank.
Water pressure forces the fertilizer out of the bag into the water
supply.
b. Care must be taken when filling the bags as they can tear.
c. Ratios are variable from 1:15 to 1:300.
8. If your injector is installed directly in a water line, be sure to install a bypass
around the injector so irrigations of plain water can be accomplished.
Phosphorous
It accumulates near emitter and P fixing capacity decides its efficiency. Low pH
near the emitter results in high fixation.
Potassium
It moves both laterally and downward and does not accumulate near emitter. Its
distribution is more uniform than N&P.
Micronutrients
Top
B. Introduction:
Give a line of introduction of the proposed business. Justification for starting the
business, scope and competition should be clearly stated.
C. Production technology:
Give detailed account of the entire production process along with the scientific
basis for each step.
9. Import of technology
10. Labour charge
11. Technical manpower
12. Pesticides, Fertilizers, preservatives
Give the costing for each of the major components and classify them into
A. Fixed cost Permanent items
B. Recurring cost planting, cultivation, maintenance, storage, packing and
transportation costs.
E. Project yield
Estimate the total production expected in different years and the realization
expected through sales.
F. Margin money
25% of the total cost that has to be invested by the entrepreneur.
G. Repayment
Principal and interest are to be repayable in seven years with a moratorium for
the first year on interest and for 2 years on principal.
Budget requirement
For a one hectare greenhouse to produce Rose cut flowers.
1.
2.
Green house
13.0
3.
Cold storage
10.0
4.
Grading and packing room
5.0
5.
Office area
2.5
6.
Refrigerated van
1.0
7.
Generator set
2.0
8.
9.
Furniture
0.5
10.
Power supply installations
1.5
11.
Water supply system, drip irrigation and misting liners
6.0
12.
Planting material and planting
30.0
1.
2.
Manures and fertilizers
1.0
3.
Plant protection
1.0
4.
Preservatives
3.0
5.
Packing material
2.0
6.
Air freight
125.0
7.
Labour charges
3.0
8.
9.
Salaries
5.0
10.
Overhead costs
0.5
11.
Maintenance cost
1.0
12.
Miscellaneous
3.7
Total investment for the project = Fixed cost + Recurring cost = 76.5 + 166.2 in
first year= 242.7.
Project yield
No. of rose plants per hectare of greenhouse = 60,000
No. of flowers expected per plant = 100 to 150
Top
The troubles which arise in the culture of crops in the greenhouse may be divided
into several groups a) failure to supply the essential factors for optimum growth
such as light, moisture, carbon dioxide and heat in amounts necessary for each
individual crop b) fertilizer deficiencies c) fertilizer excesses d) toxic gases e)
attacks by insects, animals, and allied pests and f) susceptibility to fungus,
bacteria and virus troubles.
Fertilizer deficiencies
Symptoms of deficiencies of various fertilizers have been studied over a period
of years with plants in greenhouses.
Chlorosis
This is a term used to denote the loss of normal green colour from the foliage
whether it is on the older, more mature leaves or the younger foliage. The entire
leaf may be affected, or just areas between the veins, in which case the
yellowing is most usually in irregular patches shading into the green colour.
Sometimes only the margin of the leaf or leaflets may be yellow, while the centre
of the foliage is almost a normal green.
Necrosis
This refers to the death of the area severely affected by chlorosis. Necrotic spots
or areas can also be caused by spray or aerosol damage, sunscald and other
such factors which may have no relation of fertilizer.
Nitrogen deficiency
Generally the entire plant becomes lighter green, but the effect will be most
noticeable on the older foliage. Gradually the oldest leaves loose their green
colour, and most plants become yellow. The flowers are smaller and may lack
well-developed colour.
Phosphorus deficiency
A purplish coloration developing first on the underside of the petiole, or leaf
stem, which spreads to the main veins of the leaf is characteristic of this
deficiency.
Potassium deficiency
The margins of the leaves of the older foliage become yellow, and the chlorosis
progresses toward the mid-portion of the foliage as this deficiency increases in
severity. The older leaves may drop in extreme cases of deficiency. Certain
fumigants may cause marginal burning or chlorosis, and sometimes droplets of
spray or fumigant may result in spots or blotches of chlorotic or necrotic nature.
Calcium deficiency
In sand culture, a typical symptom is the development of short clubby roots
followed in a matter of several weeks by their death. In many cases insufficient
calcium is associated with a low pH of the soil.
Iron deficiency
This is a rather common trouble although an actual lack of iron may not be the
primary cause. As iron deficiency becomes more intense, necrotic areas appear
on scattered portions of the yellow coloured leaves and the affected foliage may
drop. Iron can become deficient in soil, but often the symptoms of this deficiency
are induced by other causes from injury to the roots by over-watering or over
fertilization. Nematodes, or other soil pests interfering with root growth can also
induce iron chlorosis symptoms.
Boron deficiency
The number of cases where this is a limiting factor are few, and most of them
are with certain rose and carnation varieties. The new foliage is thick or leathery
and quickly becomes chlorotic. The rose flowers are usually very malformed. The
stem tip dies, giving rise to growth of shoots immediately below, which in turn
die at the tip, and a witches broom effect is observed. Because deficiency
Fertilizer excesses
An unfortunate belief among many growers is that when a plant does not grow
under apparently favorable conditions, the trouble can be overcome by
applications of fertilizer. This practice has resulted in untold damage or loss of
crops, as more often than not the original trouble could have been too much
fertilizer in the soil. If additional fertilizer is applied when no more is needed, the
results can be very injurious. Sometimes the difference between a high but safe
nutrient level and an injurious nutrient level is not very great and the margin of
safety may be extremely small. Therefore, it behaves the grower to test the soil
in case of doubt to determine the advisability of fertilizer application.
Nitrogen excess
The plants exhibit heavy, rank growth, with large, dark green leaves that are
often crisp and break easily. Additional nitrogen may inhibit root action, causing
typical symptoms of iron chlorosis. If the root system is killed, the plants wilt
excessively and never recover. This yellowing of the top foliage is very common
in chrysanthemums and snapdragons. Over 75 ppm of nitrates is not safe.
Phosphorus excess
Over doses of phosphorus precipitate the iron from the soil solution and make it
insoluble and unavailable, causing iron chlorosis to develop. Over 25 ppm may
cause trouble.
Potassium excess
Up to a certain point, excessive potash apparently is not injurious. Greater
amounts inhibit root action and may cause chlorosis, wilting, or immediate death
of the plant. Over 60ppm is dangerous.
Calcium excess
Usually the pH of the soil will rise when there is excessive calcium. This causes
iron chlorosis in many plants and has been called over liming injury. Over 300
ppm is high.
Iron excess
In the normal pH range of soil, there is little danger of excessive iron since
phosphorus or calcium will precipitate it from the soil solution. At ph 5.0 or lower,
iron becomes very soluble, and on hydrangeas brown dots appear on the leaves,
indicating iron is being precipitated as water vapor is lost by transpiration.
Sulfate excess
A low pH may often be characteristic of soils high in sulfates. Sometimes high
sulfates are encountered at pH 6.5. Over 600 ppm is toxic to most plants.
Boron excess
This trace elements is often found in soil to which unleached cinders have been
added or where boric acid has been applied indiscriminately. Certain water
supplies may have rather high amounts of boron. On roses, the serrations on the
margin of the leaflets of the lower leaves turn black and the remaining leaves
turn yellow and drop.
Aluminum excess
This is not troublesome except on hydrangeas that are being blued. Roots are
burnt, and the plants wilt.
Ethylene gas
This gas apparently is a by-product of metabolic processes and is given off in
very small quantities by plants or their parts. Dropping of flowers after pollination
is thought to be associated with ethylene vapors. The carnation flowers close or
may appear sleepy, that is, the ends of the petals curl inward due to ethylene
gas.
Sulphur dioxide
In very low concentrations this gas is toxic to plants. Sulphur dioxide enters the
leaf through open stomata and kills the cells nearby, thus showing patches of
dead tissues scattered over the leaf and frequently affecting the margins.
Middle-aged leaves are more susceptible than young leaves.
Damage from sulphur dioxide is commonly found in localities where coal is burnt
in large quantities. Foggy days are particularly dangerous. The common practice
of using sulphur on heating pipes in rose houses to control mildew is responsible
for leaf drop on some varieties.
Mercury damage
Many plants are quickly damaged by vapors from metallic mercury. This damage
is manifested in roses by peduncles of young buds turning yellow and later black.
The color of flowers turns dark and leaves are scorched. Breaking of mercury
thermometers or the use of bi chloride of mercury on beds as a disinfectant is
the usual way in which mercury may be released. Control measures consist of
removing all possible traces of mercury and covering the areas where mercury
was spilled or applied with a 2-inch thickness of iron filings. Paint containing
mercury as a fungicide should not be applied to rose houses.
2,4-D
The fumes of 2,4- dichlorophenoxy acetic acid and related compounds used as
weed killers cause bending, curling, and other malformations of leaves, stems,
flowers or bracts. Fumes or drift from a spray applied along the side of a
greenhouse may enter through the doors or side vents cause trouble. Therefore,
it is well to prevent trouble by keeping such sources of potential damage out of
the greenhouse, boiler room, potting shed, or any place where the fumes could
conceivably enter a greenhouse.
Phenol compounds
Many materials containing phenol or its derivatives are toxic to plants. Tar,
carbolic acid, pentachlorophenol and many others of similar nature should never
be used under glass. Treatment of wooden bench members with wood
preservatives containing phenol compounds results in severe damage to the
plants.
Top
The aim of greenhouse cultivation is to obtain high yield and good quality flower
with in a short period. Several methods for forcing flowers can be used
successfully to obtain high yield and quality.
Rose
Deshooting
Sprouting of buds just below flower, from the point between shoot and leaf lead
to smaller bud size. So these shoots should be removed regularly.
Bending
Leaf is a source of food for every plant. There should be balance between source
(assimilation ) and sink (Dissimilation).
Defoliation
The removal of leaves is known as defoliation. It is done mainly to induce certain
plant species to flower or to reduce transpiration loss during periods of stress.
Defoliation may be done by removal of leaves manually or by withholding water.
The shoots are defoliated after pruning.
Carnation
Support system (Netting)
Good support material is metal wire mesh width of 7.5 x 7.5 cm to 15 x 15 cm.
The cheapest support material is net with nylon. Minimum at every 3 meters, the
wires should be supported with poles. The poles at the beginning and the end of
each bed should be strong enough and be in cast concrete. For an optimal
support of the crop, an increasing width of meshes may be used. Eg. The bottom
net of 7.5 x 7.5 cm, then 12.5 x 12.5 cm and the upper nets 15 x 15 cm.
Pinching
Pinching refers to breaking out the tip of shoot with few leaves and encouraging
growth of side shoots. There are three types of pinching
a) single b) one and half and c) double pinches
Pinching is done at a stage when the plants are young and between of 7-15cm
height. Since very tender shoots are usually pinched, no special tool is required.
It is done by snapping the shoot tip manually. A sharp knife or blade may be used
for pinching. When the plant attains 6 nodes, the first pinch is given. This is
referred as single pinch. This would give rise to six lateral shoots. With a one
and half pinch, 2-3 of these lateral shoots are pinched again. For the double
pinch all the lateral shoots are pinched off. Other than carnation, pinching is also
practiced in marigold, Gomphrena (single pinch), and spray types of
chrysanthemum (double pinch).
Disbudding
Disbudding refers to removal of side shoots so that the central/terminal bud
receives maximum food for the full development. In standard carnations, side
buds should be removed where as in spray carnations, the terminal bud has to
be removed.
Chrysanthemum
Pinching out the apical bud
As soon as the bud stems begin to elongate in other words as soon as the buds
have just separated from one another, it is used to pinch out the central bud, this
improves the spray shape. If pinching out is done too early, damage may be
caused to the side buds, so it is carried out between 2nd and 3rd weeks before
harvesting.
Top
Rose
Blind wood
The normal flowering shoot on a greenhouse rose possesses fully expanded
sepals, petals, and reproductive parts. The failure to develop a flower on the
apical end of the stem is a common occurrence-such shoots are termed blind.
The sepals and petals are present, but the reproductive parts are absent or
aborted. Blind wood is generally short and thin, but it may attain considerable
length and thickness when it develops at the top of the plant. This may be
caused by insufficient light, chemical residues, insect, pests, fungal diseases and
other factors.
Colour fading
Off- coloured flowers present a problem with some yellow varieties in that the
petals may be green or a dirty white instead of a clear yellow. Raising the night
temperature several degrees will reduce the number of off-coloured flowers.
Occasionally the pink or red varieties develop bluish-coloured flowers. This is
very often associated with use of organic phosphate and various other kinds of
insecticides.
Limp necks
The area of the stem just below the flower wilts and will not support the head.
Sometimes this is due to insufficient water absorption; cutting off the lower 1 to
2 inches of stem and placing the cut stem in water at 37C will revive the flower.
Nutritional disorders
Iron deficiencies can cause pale foliage. Adjusting the pH of the soil may solve
this problem
Carnation
Splitting of calyx
The calyx may split down either half or completely. The petals are deprived of
their support, which results into bending down of petals. Thus, the regularity of
shape and structure of the flower destroyed. Splitting is associated with weather,
particularly where light and temperature fluctuate. Some reduction in splitting
can be obtained by keeping the night temperature at 5F. High plant density per
unit area caused more calyx splitting. Increasing doses of N reduced the number
of split calyces while increase in potassium rates enhanced it. Varieties tolerant
to calyx splitting are Epson, palmir etc.
Curly tip
This disorder affects the growing tips which curl and become distorted. Tips of
the young shoots fail to separate and continuation of growth results in a
characteristic curvature. Poor light and other adverse conditions are thought to
be the causes of the disorder. Water stress and potassium deficiency are
suspected causes for a physiological curly tip and die-back of carnation flowers.
Chrysanthemum
Blindness
It occurs when the night temperature is too low and the days are short at the
time when flower buds are forming. A rosetted type of growth is indicative of this
difficulty. Center petals that fail to develop can be due to excessive heat; or in
dark weather some varieties apparently lack enough food to open the flower.
Chlorosis, or yellowing of the upper foliage, is generally associated with over
watering, excessive fertilizer in the soil, or insects or diseases attacking the root
system. Continued growth of shoots and failure to form flower buds when short
days are started the mean night temperature was too low. Sunscald is prevalent
on standards in flower in very warm weather. The petals turn brown and dry up.
Gerbera
Bushiness
An abnormality characterized by numerous leaves, short petioles and small
laminae, which gives some cultivars of gerbera a bushy appearance known as
bushiness. Nodes are not clearly distinguished and no internode elongation is
seen.
Stem break
It is common post harvest disorder in cut gerberas. This is mainly caused by
water imbalances. It could be ethylene controlled and associated with early
senescence associated with water stress.
Anthurium
Excess light
Leaves appear bleached in the centers and may have brown tips. To control this
problem, shade should be given so as to reduce the light level to 1800-2500 footcandles.
Gladioli
Fluoride injury
Leaf scorch of gladioli due to the presence of fluorine compounds in the
atmosphere which accumulated on the tips of leaves. The injury is associated
with heavy application of super phosphate.
Top
Cut flower quality and longevity are influenced by pre and post harvest practices.
Nearly 20-40% of the cut flowers produced are lost due to faulty harvesting, post
harvest handling, storage, transportation and marketing. These losses can be
reduced by careful harvesting, post harvest handling, temperature management,
sanitation and judicious use of floral preservatives.
Harvesting
Maturity of the cut flower mainly decides its post harvest life. The flowers must
reach certain stage of development before harvesting. Most of the cut flowers
are harvested in the early morning or late in the afternoon. Flowers are
harvested with sharp knife or secature.
Rose
Harvesting is done at the tight bud stage when the colour is fully developed and
the petals have not yet started unfolding.
Gladioli
The spikes are cut in tight bud stage when colour has fully developed in the
mature unopened buds leaving 4 leaves on the plant.
Carnation
Standard carnation flowers are harvested when the outer petals unfold nearly
perpendicular to the stem. Spray types are harvested when two flowers open
and the remaining buds show colour.
Chrysanthemum
Standard flowers are cut soon after the disappearance of green colour in the
centre of the flowers and the center petals are fully expanded. Pompons are cut
when they are fully developed. Spray types should be cut when the central
flower is open and the surrounding flowers are well developed and the varieties
which shed pollen badly will have to be cut before they become unsighty. Cutting
the stem while the flowers are slightly on the green side is preferred because it
offers a better quality product for the customer. The stems are harvested by
pulling them out and breaking of the root system leaving it behind in the
bed/field be ploughed into the soil when bed/field is prepared for next crop.
Orchid
Flowers are harvested when they are fully open as the flowers cut prior to their
maturity will wilt before reaching the wholesaler.
Anthurium
Flowers are harvested when the spathe completely unfurls and the spadix is well
developed. Harvesting the blooms, when one third of the flowers on the spadix
mature, change of colour can be observed that moves from base to tip of spadix.
At this stage the flowers are harvested. Harvesting has to be done during cooler
parts of the day i.e.) early morning or late evening In general the cut blooms are
placed in water held in plastic buckets immediately after cutting from the plant.
Delay in keeping in water allows air entry into the stem and causes blockage of
the vascular vessels. Cut flowers after harvest should be shifted to pre cooling
chambers in refrigerated vehicles having 2-4C temperature as they deteriorate
most rapidly at high temperature. After reaching the cooling chamber, another
cut is given above the previous cut in roses, whereas in orchids lower 0.75 cm of
the peduncle is cut. In gladioli, 2.5 cm diagonal cut is made to expose maximum
capillary tissues for absorbing more water
Pre cooling
Pre cooling removes field heat rapidly from the freshly harvested cut flowers.
Precooling lowers respiration rate, water loss and ethylene synthesis. Most of the
time, greatest loss occurs due to delay in precooling. Generally two methods of
cooling are followed. The first one is room cooling and the other one is forced aircooling. In room cooling, the flowers are held in buckets which are placed in a
cooler. In the forced air cooling system, the flowers packed in perforated boxes
are subjected to cool air blasts for a specific period in a closed room to remove
field heat. The flowers take 20-30 minutes for cooling in forced cooling
depending on the flower type and initial temperature in the box. Proper
temperature (1.7C to 4C) and relative humidity (90-95%) maintenance are
critical to the success of precooling, otherwise the flowers will dessicate.
Rose
Roses must be placed in a bucket of water inside the polyhouse immediately
after harvesting and transported to cold storage (2-4C). The length of time
depends upon the variety and quality of the roses.The flowers are graded
according to the length. It varies from 40-70 cm depending on the variety and
packed in 10/12 per bunch
Carnation
After harvest, the flower stems have to be trimmed at the base and should be
immediately placed in a bucket of preservative solution of warm and deionized
water. A good preservative solution for carnations should be acidic (pH 4.5) with
2-5% sucrose and a biocide not phytotoxic to carnations. After keeping in
preservative solution for 2 to 4 hours, flowers should be placed in a refrigerated
room at 0-2C for 12-24 hours. The flowers can be stored for two to four weeks
before marketing. For this, the flowers have to be packed in cartons lined with
polyethylene film. These cartons should have sufficient vent holes. The full
cartons should be pre-cooled with out lid. The plastic is then loosely folded on
top of the stems and the lid is closed. These cartons are stored in cool chambers
designed to maintained 0C with good air circulation and a constant relative
humidity of 90-95%.
Chrysanthemum
After harvest, the stem have to be cut at equal length (90 cm is the standard),
bunched in five putting a rubber band at the base and sliding them into a plastic
sleeve and putting the bunches in plastic buckets filled with water. Early morning
on the day of shipment (or night before) the bunches can be packed in boxes.
Gerbera
Harvesting is done when outer 2-3 rows of disc florets are perpendicular to the
stalk. The heel for the stalk should be cut about 2-3 cm above the base and kept
in fresh chlorinated water.
Orchids
Storage
Since most orchid flowers are long-lived on the plants, they should not be
harvested until needed. If these are to be cut they should be stored at 5-7C. At
this temperature most orchid flowers can be stored for 10 to 14 days. Plastic film
storage is attractive and can be utilized.
Packaging
Packaging is another important aspect in the flower trade. An ideal package
should be airtight, water proof, strong enough to withstand handling and small in
volume. Many ways are followed to pack orchid flowers. Cymbidium spikes are
often packed 100 flowers to a box. Standard florist boxes are used for the
packing of Cattleya floors. Hawaiin Dendrobium is packed in 4 dozen sprays per
box. Keeping of a wet cotton at the cut end of the flower stem which is wrapped
with a polythene wrapper helps to maintain humidity.
Vase- life
Immediately after arrival, the lower 0.75 cm of the peduncle is cut off, and the
flower is inserted into a fresh tube of water containing preservative. In case of
spray type of orchids, the basal 2.5cm of the stem is cut upon arrival, placed in
warm water at 38C with a preservative and hardened off at 5C. Foliar
application of aluminium chloride at 500ppm, ammonium molybdate at 100 ppm
or boric acid at 1000ppm increased the vase-life of Oncidium.. Hydroxyquinoline
resulted in additional bloom opening of the flowers and also increased the vaselife.
Anthurium
Flowers can be easily stored at 13C for 2-3 weeks. The flowers, which are
harvested when 3/4th of the length of the spadix colour changes, lasts longer
than the other flowers which are harvested either early or late. The average vase
life depends upon life of flowers range between 12-24 days depending upon the
cultivars. Anthurium is packed in cartons lined with impervious polyethylene
sheeting of adequate length and width so that, when packed, the sheet can be
folded over to prevent the moisture of the dampened flowers and packing
material from dampening the box itself. Newspaper is used to line the carton,
and shredded newspaper is used to cushion spathes that are arranged in rows
facing opposite directions. Each individual spathe is wrapped and tucked with unprinted newspaper or other white paper.