Professional Documents
Culture Documents
Installation Manual Series ED104: Power Amplifier For Pressure Valves
Installation Manual Series ED104: Power Amplifier For Pressure Valves
Installation Manual
Series ED104
Contents
Installation Manual
Note
This document and other information from Parker Hannifin GmbH, its
subsidiaries, sales offices and authorized distributors provide product or
system options for further investigation by users having technical
expertise. Before you select or use any product or system it is important
that you analyse all aspects of your application and review the information
concerning the product or system in the current product catalogue. Due
to the variety of operating conditions and applications for these products
or systems, the user, through his own analysis and testing, is solely
responsible for making the final selection of the products and systems
and assuring that all performance and safety requirements of the
application are met. The products are subject to change by Parker
Hannifin GmbH at any time without notice.
IA ED104 UK A5.PM6.5 RH
Hydraulics
Home
Installation Manual
Electronic module for the control of proportional
pressure relief valves. The pressure values and
the changing sequence are determined by externally applied command signals as well as internal
limit and ramp potentiometers. The measurement
value (Volts) at the module is indirectly proportional with the pressure level, which is in turn influenced
by the volume of flow (quantity, viscosity).
Features
Characteristics
Power supply
Power required
Set value voltage
Input select voltage
Reference outputs
Solenoid output current max.
Ramp times
Ambient temperature
Connection
Shielded cable connections
Fuse
Ordering Code
ED
104
00
Electronic Module
Pressure Valves
Module
Type
Design
Series
for Valves
Code
Module Type
DSA
DWU
DWE
104
Amplifier,
adjustable
Min/Max-limits
Up/Down-ramps
IA ED104 UK A5.PM6.5 RH
Hydraulics
Home
Installation Manual
EMC
EN 50081-2
EN 50082-2
EN 55011
ENV 50140
EN 61000-4-4
ENV 50204
EN 61000-4-5
EN 61000-4-2
EN 61000-4-6
Block Diagram
Connector (Elevation B)
14
16
18
22
26
11
13
25
27
31
IA ED104 UK A5.PM6.5 RH
Hydraulics
Home
Installation Manual
Operating and Diagnostic Elements
(Elevation A)
Notes
Turn off the electrical power
to this board whenever the
hydraulic supply to the valve
is not on.
Dimensions
IA ED104 UK A5.PM6.5 RH
Hydraulics
Home
Installation Manual
( 2.5 Amp.)
( 5.0 Amp.)
(10.0 Amp.)
Relais and solenoids operating from the same supply circuit than the valve electronics has to be fitted
by surge protection elements.
Wiring Cable
The wires between the installation site of the module and the peripheral units, as power supply, valve
solenoids, position transducer, command signal source has to be shielded. The following wire sizes
must be reached: power supply AWG 16, other connections AWG 20. The capacity should not exceed
a value of approx. 130 pF/m (wire/wire). The maximum cable length is 50m. No power current lines may
be placed within the wired shielded cables to the electronic module. The cable shield has to be
connected to ground at both ends (see also chapter Grounding). Please be aware of ground loops.
Connectors
The connection of the position transducer needs a sensor connector 4pin+E featuring metal case and
integrated cable shield coupling. Parker can provide suitable connectors:
5004108
(Connector 4pin+E)
The connectors has to be installed according the connection diagram, the cable shield has to be tied
on the whole periphery to the provided coupling clamp.
Installation
The module has to be mounted within a conductive, shielded enclosure. Usable is i.e. an EMC-approved
control cabinet. A perfect grounding of the enclosure is mandatory (see also chapter "Grounding")
Grounding
The mounting plate of the valve has to be connected to the grounded metal machine frame. The cable
shields must be tied to ground at the control cabinet. A low-ohmic potential compensation wire has to
be provided between the control cabinet and the machine frame (cable wire >AWG 7 cross section) to
prevent ground loops.
IA ED104 UK A5.PM6.5 RH
Hydraulics
Home