Professional Documents
Culture Documents
Basics of Steam System Design
Basics of Steam System Design
by W. M. (Bill) Huitt
Introduction
This section is intended for people involved in the design, operation and/or maintenance of steam systems. It covers
some basic terminology, principles, steam generation in general, and the design of steam distribution and condensate
collection piping. Also covered are the sizing, specifying and installation of steam traps.
Terminology
Absolute Pressure:
The theoretical pressureless state of a perfect vacuum is "absolute zero". Absolute pressure is, therefore, the pressure
above absolute zero. At sea level, for instance, the pressure exerted by the atmosphere is 14.7 PSI absolute. Absolute
pressure, when measured as pounds per square inch, is indicated as "PSIA". It is also commonly measured in
millimeters of mercury, or "mm Hg".
Gauge Pressure:
Gauge pressure is the internal pressure, as indicated on a gauge, of a sealed system. Such as a tank or piping system.
Gauge pressure measures the pressure above atmospheric pressure where zero pounds gauge equals approximately
14.7 PSIA. Below zero pounds gauge a vacuum exists which is often expressed in either inches of mercury (Hg) or
inches of water (H20). Gauge pressure indication is shown as PSIG.
Enthalpy:
Enthalpy is the total energy, due to both pressure and temperature, of a fluid or vapor at any given time or condition.
The basic unit of measurement for all types of energy is the British Thermal Unit (BTU).
Specific Enthalpy:
A measure of the ability of a substance to absorb heat. It is the amount of energy (BTU's) required to raise 1 pound
of water 1 F. Thus specific heat capacity is expressed in BTU/lb/ F.
The specific heat capacity of water is 1 BTU/lb/ F. This means that an increase in enthalpy of 1 BTU will raise the
temperature of 1 pound of water by 1 F.
Heat:
Heat is a form of energy and as such is part of the enthalpy of a liquid or gas.
Heat Transfer:
Heat transfer is the flow of enthalpy from matter at a high temperature to matter at a lower temperature when
brought into contact.
Expressed in BTU's, this is the amount of heat required to raise the temperature of 1 pound of water from 32 F to
the boiling point of a given pressure/temperature correlation. Also referred to as Sensible Heat.
EXAMPLE
Let us assume that 50 F water is available as feedwater to a boiler at atmospheric pressure. The water will begin to
boil at 212 F. 1 BTU will be required to raise each pound of water 1 F. Therefore, for each pound of water in the
boiler, the increase in enthalpy required to raise the temperature from 50 F to 212 F is:
If the boiler holds 22000 pounds mass (2638 gallons) the increase in enthalpy to bring the total mass of water to it's
boiling point is therefore:
It must be remembered, this figure is not the sensible heat, but merely the increase in sensible heat required to raise
the temperature from 50 F to 212 F. The datum point of the steam tables is water at 32 F, which is assumed to
have a heat content of zero for our purposes. (The absolute heat content clearly would be considerable, if measured
from absolute zero at minus 459 F). The total sensible heat of water at 212 F is therefore:
Expressed in BTU's, this is the amount of heat required to change 1 pound of boiling water to 1 pound of steam.
This same amount of heat is released when a pound of steam is condensed back to a pound of water. The quantity of
latent heat will vary with the pressure and/or temperature of a closed system.
The sum of the Heat of the Liquid and Latent Heat of Evaporation, also expressed in BTU's.
Flash Steam:
When hot condensate, under pressure, is released to a lower pressure, a percentage of it is re-evaporated into flash
steam. Depending on various economics, this can certainly be a viable source of low pressure steam.
Steam
This is the oldest and most widely used form of energy in industry. Yet in most plants and engineering offices it is
still not understood to a large degree. It is neglected in an even larger degree. In a larger sense, plant operations quite
often can’t see the forest for the trees. That is, until there’s a forest fire.
What is meant by that is that steam is used in such a wide spread manner in most heavy industrial manufacturing
plants that it’s taken for granted until something fails. A good example of that is the care and maintenance of
strainers installed upstream of steam traps in order to prevent the trap from plugging up from various deposits of
pipe scale and chemical residue. That same thinking would logically conclude that if scale and residue are
anticipated then it would stand to reason that the strainers should be blown down and/or cleaned out periodically.
It is surprising the number of times a systems failure or reduction in efficiency can be attributed to something as
simple as the impacted build-up of scale in strainers; something that could have been averted with a little planned
preventative maintenance. In conjunction with that is the periodic testing of the steam traps, all too often steam
systems are installed and forgotten. Until, as mentioned earlier, a system breaks down or gradually becomes more
and more inefficient.
Inefficiency translates into additional operating costs. In older plants the savings potential is enormous. Not only
from a fiscal standpoint, but also from an environmental standpoint.
A good way to find out how current a plant is with it's steam system maintenance is to find out if there is a steam
distribution list, a location plan or any kind of a record accounting for all of the steam traps throughout the plant. If
any of these items do exist, when was the last time they were checked or updated? And, are they actually used as a
preventative maintenance tool?
In a surprising number of plants the answer is that there is no formal record of any kind for steam traps. If this is true
in your plant then this is an indication that the potential for both cost savings and increased production is a likely
possibility.
Steam is the gas phase of water. It is created when heat energy is added to the water until, at some corresponding
point of pressure and temperature, the water can no longer remain as a liquid. This is called the "Saturation" point
and any additional heat energy added to the water at this point, will cause some of the water to boil off as steam.
This action is referred to as evaporation. The energy in the evaporated state is referred to as the "Latent Heat of
Evaporation".
The amount of energy required for evaporation, at lower pressures, is significantly higher than the amount of energy
needed to bring that same water to its saturation point. The condensing process of steam takes place when the steam
is allowed to give up its latent heat content and condense back to a liquid state.
The latent heat content of the steam is the energy that is given up so readily for heat transfer. In fact the steam is so
willing to give up this heat energy that we have to take various measures, sometimes costly, just to contain it long
enough to get it to where we need to use it. Some of these measures include insulation to contain the heat, steam
traps and separators to keep condensate from accumulating in the distribution piping and proper line sizing to reduce
friction loss. These measures will be covered in more detail later.
Steam can exist in either a saturated condition or a superheated condition. The temperature of saturated steam is in
constant correlation with its pressure. If you know what the temperature of saturated steam is you then know what
the pressure is. Inversely, if you know what the pressure is you then know what the temperature is. To illustrate; if
we were to take a container with a volume of 26.8 cubic feet and pour in 1 pound of water at the temperature of
melting ice, 32 F, in all practicality the heat content, or enthalpy, would be zero. We would then begin adding heat
to the water, which is at atmospheric pressure, until it reached 212 F. The heat content of that water will then be
180.2 BTU's. By adding additional heat, or enthalpy, to the water it will begin to change state and evaporate into
steam. The heat content of this latent heat of evaporation is 970.6 BTU's. At atmospheric conditions these numbers
will always be constant. Water at it's saturation point will contain 180.2 BTU/lb and any steam that is formed will
contain 970.6 BTU/lb.
By sealing our container, and continuing to heat the water until it has been completely evaporated, that 1 pound of
water, with a volume of .016 cubic feet, has been transformed into 1 pound of steam with a volume of 26.8 cubic
feet. That is an increase in volume of 1675 times. This is indeed one of the considerations in designing for steam
distribution, mass volume.
At atmospheric pressure we now know that the constants are: 212 F at saturation point, heat content of the liquid is
180.2 BTU/lb, heat content of the steam is 970.6 BTU/lb and the specific volume of the steam is 26.8 cubic feet.
Now we will remove the seal on our container and install a vertical piston, one that doesn’t leak around the edges.
The only thing holding down the piston initially is atmospheric pressure at 14.7 P.S.I.A. or zero P.S.I.G.
Consequently the container still has a volume of 26.8 cubic feet and the steam is still at atmospheric pressure. By
adding a 10 P.S.I. weight on top of the piston, two things happen. The steam condenses back to water and the
volume in the container is reduced. However the heat of the liquid still remains at 180.2 BTU's. With 10 P.S.I. of
compression on the hot water in the container it will take more energy to release the molecules into steam. At 10
PSIG the saturation or boiling point of water is 239.4 F at which point the heat of the liquid will be 207.9 BTU/lb.
By adding an additional 27.7 BTU to the water we can bring it to it's saturation point of 239.4 F. If we continue to
add heat the water will begin to boil off to steam. If we boil off the entire pound of water under the 10 P.S.I.
pressure the latent heat of the steam will then be 952.9 BTU's and occupy 16.5 cubic ft.
Under 10 PSI pressure the constants are: 239.4 F saturation point, heat content of the liquid is 207.9 BTU/lb, heat
content of the steam is 952.9 BTU/lb and specific volume of the steam is 16.5 cubic feet.
Superheated steam, on the other hand, does not have a pressure/temperature correlation. Saturated steam and water
exist at the same pressure and temperature. If heat transfer continues into the steam after saturation and evaporation
has been accomplished, the steam temperature will continue to raise. Once it has exceeded the temperature of
saturated steam at a corresponding pressure it becomes superheated. This superheat condition can be manufactured
to achieve a certain amount of superheat for use in mechanical work such as steam turbines or for transmission over
long distances (this will be discussed later). It can also be the unneeded result at pressure reducing stations and other
cases where there is a turndown of steam pressure to effect temperature control or pressure control, the amount of
superheat depends on the turndown ratio.
All of the information just discussed has fortunately been compiled into steam tables. One table referred to is
"Properties of Saturated Steam and Saturated Water"; the other is "Properties of Superheated Steam". These tables
show us the correlation of this data for various pressures and temperatures. By referring to the steam tables we find
the constants that were discussed plus a column for "Total Heat of Steam" and "Specific Volume of Liquid". The
"Heat of the Liquid" is also referred to as "Sensible Heat". It should also be noted that in the "Properties of
Superheated Steam" there is no liquid heat content since liquid does not exist in superheat. There are also various
temperatures at any given pressure because there is no correlation in superheated steam between pressure and
temperature.
Gauge Pressure:
Indicated in Inches of Hg for vacuum below atmospheric pressure, and P.S.I.G. for pressures above atmospheric.
Absolute Pressure:
Indicated in P.S.I.A. with zero being absolute zero or 14.7 P.S.I. below atmospheric pressure.
Temperature:
The figures in this column represent the heat content, in BTU/lb, for water at the indicated pressure/ temperature.
Indicated in BTU/lb, this is the amount of heat content in every pound of steam at the indicated
pressure/temperature.
Indicated in BTU/lb, this is the sum of both the Heat of the Liquid and the Latent Heat of Evaporation or the total
heat content of the steam at the indicated pressure/temperature.
Specific Volume:
Indicated in cubic ft./lb, this is the space occupied by 1 pound of water or 1 lb of steam at the indicated
pressure/temperature.