Professional Documents
Culture Documents
Off Grid PV Systems System Install Guidelines
Off Grid PV Systems System Install Guidelines
These guidelines have been developed by the Sustainable Energy Industry Association of the Pacific Islands in
Collaboration with the Pacific Power Association
They represent latest industry BEST PRACTICE for the design and installation of PV Grid Connect Systems.
Copyright 2012
While all care has been taken to ensure this guideline is free from omission and error, no responsibility can be taken
for the use of this information in the design of any PV grid connect system.
GENERAL
The performance of a reliable installation, that fulfils a customers needs, requires both careful design
and correct installation practice and conformance to relevant standards.
AS/NZS 3000
Wiring Rules
AS/NZS 4509
Stand-alone power systems
AS 4086.2
Secondary batteries for stand-alone power supplies
AS/NZS5033
PV Array
AS 3010.1
Electrical Installations
Supply Generating set
AS 3595
Energy management programs
AS 1359.51
Noise level limits
AS 1768
Lightning Protection
In USA PV systems must be in accordance with following codes and standards:
Electrical Codes-National Electrical Code Article 690:Solar Photovoltaic Systems and NFPA 70
UL Standard 1741 , Standard for Inverter, converters, Controllers and Interconnection System
Equipment for use with Distributed Energy Resources
DOCUMENTATION
All complex systems require a user manual for the customer. Off-grid power systems are no different.
The documentation for system installation that should be provided include
Page 1
PV ARRAY
ORIENTATION AND INCLINATION
For best year round performance a fixed array should be mounted facing true north ( 10 ) in South Pacific or
True South ( 10 ) in North Pacific at an inclination equal to the latitude angle in the tropics and latitude
angle plus 5 to 15 outside of the tropics.
Between latitudes 10 South and 10North the array should be tilted at a minimum of 10 degrees.
However the correct tilt angle should be determined based on energy usage and also the local weather
conditions at different times of the year. For example if an island typically has very cloudy conditions in one
period of the year (e.g. wet season) then the array should be tilted to suit the suns altitude in the sunny period
of the year.
True NORTH
True South
PV Module
PV Module
LATITUDE ANGLE
E.g. for SUVA ( Lat 18o S )
The tilt angle should be approximately 18
Figure 1 a
LATITUDE ANGLE
E.g. for PALUA ( Lat 7o )
The tilt angle should be approximately 7. H owever
because of the cloud cover in the wet season a
tilt angle of 20 would be better. This would resul t
in a greater energy output from the array in the dry
season.
Figure 1b
.
An alternative mounting arrangement can allow seasonal adjustment of array tilt to increase the energy input.
ROOF MOUNTING
If the modules use crystalline cells then it is preferable to allow sufficient space below the array (> 50mm or
2 inches) for ventilation cooling. This will be subject to the constraints of the customer or architect.
It is important to allow sufficient clearance to facilitate self cleaning of the roof to prevent the build up of
leaves and other debris.
If fauna are a problem in the vicinity of the installation then consideration should be given to how to
prevent them gaining access under the array.(see cable protection)
All supports, brackets, screws and other metal parts should be of similar material or stainless steel to
minimise corrosion. If dissimilar metals (based on their galvanic rating) are used then the two surfaces of
the metals should be separated by using rubber washes or similar.
Where timber is used it must be suitable for long-term external use and fixed so that trapped moisture
cannot cause corrosion of the roof and/or rotting of the timber. The expected replacement time should be
stated in the system documentation.
Any roof penetrations must be suitably sealed and waterproof for the expected life of the system. If this is
not possible then this must be detailed in Maintenance Timetable
All fixings must ensure structural security when subject to the highest wind speeds for the region and local
terrain - This may require specific tests of the fixing/substrate combination on that roof.
The installer shall ensure that the array frame that they install has applicable engineering certificates
verifying that the frame meets wind loadings for that particular location.
The installer must follow the array frame suppliers/manufacturers recommendations when mounting the
array to the roof support structure to ensure that the array structure still meets wind loading certification.
All external wiring must be protected from UV and mechanical damage in such a manner that it will last the
life of the system..
Issue 1 September 2012
Page 2
BATTERY INSTALLATION
LAYOUT OF BATTERY ENCLOSURE
The main considerations for the battery enclosure are
To negate the risk of explosion there must be no opportunity for hydrogen to build up. This requires adequate
ventilation with no possibility of spark ignition.
VENTILATION (Metric Calculations)
Ventilation must be provided. The minimum area required for natural ventilation for both inlet and outlet
apertures (for wet lead acid batteries) are given by
A = 100qv cm
Where qv is the minimum exhaust ventilation rate
in litres per second = 0.006 x n x I
and
n = the number of battery cells
I = the charging rate in amperes
NOTE : The charging rate in amperes is the maximum output rating of the largest charging source or the rating of its
output fuse or circuit breaker. Where two parallel battery banks are used, the charging rate is halved.
Best practice is to provide input ventilation vents below the level of battery and the output vents on the
opposite side of the batteries, as high as possible in the enclosure to prevent hydrogen build up.
VENTILATION (Imperial Calculations)
Ventilation must be provided. . The minimum area required for natural ventilation for both inlet and outlet
apertures (for wet lead acid batteries) are given by
A = 15.5qv in
Where qv is the minimum exhaust ventilation rate
in litres per second = 0.006 x n x I
and
n = the number of battery cells
I = the charging rate in amperes
NOTE : The charging rate in amperes is the maximum output rating of the largest charging source or the rating of its
output fuse or circuit breaker. Where two parallel battery banks are used, the charging rate is halved.
Best practice is to provide input ventilation vents below the level of battery and the output vents on the
opposite side of the batteries, as high as possible in the enclosure to prevent hydrogen build up.
Page 3
battery charging equipment should be hard wired, do not use temporary connection.
battery terminals should be shrouded to prevent inadvertent short circuits.
ensure sufficient clearance between battery terminals and metal walls
( or insulate using non-metallic sheet )
Battery fusing preferably should not be in the same enclosure as the battery bank but if they are then they
should be either a minimum of 500mm away from the batteries or 100mm below the top of the batteries.
Another method to keep the fuse separate from the battery bank is to place a vertical partition between the
batteries and the fuse, thereby keeping the fuse as close to the batteries as possible but isolated from any
hydrogen build up. In any case the main battery fusing should be located below the battery vents. (Normally
below the top of the batteries).
PREVENTING EXCESSIVE CURRENT FROM BATTERIES
Battery shorts are prevented by shrouding terminals and ensuring safe separation between live terminals.
Battery shorts are controlled by using appropriate circuit protection.
Overcurrent protection is to be provided in each battery output conductor except where one side of the battery
bank is earthed (ground), in which case only the unearthed (ungrounded) conductor requires overcurrent
protection.
Normal practice is to either fuse the positive and earth (ground) the negative or fuse all conductors.
ACID LEAKAGE
Provision must be made to contain any spilled electrolyte. Battery trays should be able to hold at least the
electrolyte content of one cell of the battery bank.
ACID SPLASHES
A ready supply of water should be available and any person working on the batteries should wear rubber
gloves, safety glasses and long sleeved protective clothing. Eye wash equipment should be available, in case
of accident.
Walls near the batteries should be protected by acid resistant paint or non-metallic sheet.
SAFETY AND WARNING SIGNS
A battery explosion warning" sign must be mounted so that it is clearly visible on approach to the battery
bank. An "electrolyte safety" sign should be mounted adjacent to the battery bank.
MAIN BATTERY PROTECTION
Overcurrent protection and the ability to readily isolate a battery bank must be provided.
Issue 1 September 2012
Page 4
For each inverter power rating determine the current drawn from the battery bank using
I
NOTE : Allowance for any significant DC demand must be included when sizing the main protection
The following sizing methods (based on voltage drops) can be used for all types of currently available copper
cable.
NOTE : the rated voltage or current carrying capacity (CCC) of any cable must never be exceeded eg. some
automotive types are rated at 32V
2
15
3.2
20
5
25
7.5
45
15
70
0.09
0.18
0.27
0.37
0.46
0.55
0.73
0.92
1.37
1.83
2.75
0.06
0.11
0.17
0.23
0.29
0.34
0.46
0.57
0.86
1.14
1.72
2.29
0.04
0.07
0.11
0.15
0.18
0.22
0.29
0.37
0.55
0.73
1.10
1.46
1.83
0.02
0.05
0.07
0.10
0.12
0.15
0.20
0.24
0.37
0.49
0.73
0.98
1.22
1.46
1.95
0.01
0.02
0.04
0.05
0.06
0.07
0.10
0.12
0.18
0.24
0.37
0.49
0.61
0.73
0.98
1.22
Page 5
3. Route lengths to produce 5% voltage drop (12V systems) for twin cable ( using the above formula )
Maximum Distance in metres to produce 5% voltage drop (12V system)
2
1.5mm
2.5mm
4mm
6mm
10mm
Current (A)
1mm
16mm
16.4
24.6
41
65.6
98.4
163.9
262.3
8.2
12.3
20.5
32.8
49.2
82
131.1
5.5
8.2
13.7
21.9
32.8
54.6
87.4
4.1
6.1
10.2
16.4
24.6
41.0
65.6
3.3
4.9
8.2
13.1
19.7
32.8
52.5
2.7
4.1
6.8
10.9
16.4
27.3
43.7
2.3
3.5
5.9
9.4
14.1
23.4
37.5
2.0
3.1
5.1
8.2
12.3
20.5
32.8
1.8
2.7
4.6
7.3
10.9
18.2
29.1
10
1.6
2.5
4.1
6.6
9.8
16.4
26.2
11
1.5
2.2
3.7
6.0
8.9
14.9
23.8
12
1.4
2.0
3.4
5.5
8.2
13.7
21.9
13
1.9
3.2
5.0
7.6
12.6
20.2
14
1.8
2.9
4.7
7.0
11.7
18.7
15
1.6
2.7
4.4
6.6
10.9
17.5
16
1.5
2.6
4.1
6.1
10.2
16.4
17
2.4
3.9
5.8
9.6
15.4
18
2.3
3.6
5.5
9.1
14.6
19
2.2
3.5
5.2
8.6
13.8
20
2.0
3.3
4.9
8.2
13.1
The following sizing methods (based on voltage drops) can be used for all types of currently available copper
cable.
Page 6
3. Route lengths to produce 5% voltage drop (12V systems) for twin cable ( using the above formula )
Maximum Distance in feet to produce 5% voltage drop (12V system)
Wire Size- AWG
(mm)
Current (A)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
14
(2.08)
12
(3.31)
10
(5.26)
8
(8.36)
6
(13.29)
4
(21.14)
2
(33.61)
1
(42.39)
95.5
47.8
31.8
23.9
19.1
15.9
13.6
11.9
10.6
9.6
8.7
8.0
7.3
6.8
6.4
6.0
5.6
5.3
5.0
4.8
151.5
75.8
50.5
37.9
30.3
25.3
21.6
18.9
16.8
15.2
13.8
12.6
11.7
10.8
10.1
9.5
8.9
8.4
8.0
7.6
241.9
121.0
80.6
60.5
48.4
40.3
34.6
30.2
26.9
24.2
22.0
20.2
18.6
17.3
16.1
15.1
14.2
13.4
12.7
12.1
385.6
192.8
128.5
96.4
77.1
64.3
55.1
48.2
42.8
38.6
35.1
32.1
29.7
27.5
25.7
24.1
22.7
21.4
20.3
19.3
611.0
305.5
203.7
152.7
122.2
101.8
87.3
76.4
67.9
61.1
55.5
50.9
47.0
43.6
40.7
38.2
35.9
33.9
32.2
30.5
974.0
487.0
324.7
243.5
194.8
162.3
139.1
121.8
108.2
97.4
88.5
81.2
74.9
69.6
64.9
60.9
57.3
54.1
51.3
48.7
1546.4
773.2
515.5
386.6
309.3
257.7
220.9
193.3
171.8
154.6
140.6
128.9
119.0
110.5
103.1
96.6
91.0
85.9
81.4
77.3
1948.1
974.0
649.4
487.0
389.6
324.7
278.3
243.5
216.5
194.8
177.1
162.3
149.9
139.1
129.9
121.8
114.6
108.2
102.5
97.4
CABLE PROTECTION
All sub-circuits, including PV array and auxiliary charging circuits should be protected by HRC fuses or circuit
breakers. In addition these circuits being capable of being isolated without the use of tools. Any circuit
breaker used in DC circuits must be rated for the appropriate DC voltage and be non-polarised.
Issue 1 September 2012
Page 7
All cables used in the installation should be securely fixed in place to minimise any movement of the cable.
Any exposed cabling will be protected from UV and mechanical damage eg. run in conduit.
Crimp style termination of wiring should use the appropriate crimping tool.
LICENCING
EXTRA LOW VOLTAGE ( ELV )
All extra low voltage wiring should be performed by a 'competent' person, which is defined as
" a person who has acquired through training, qualifications, experience or a combination of these, knowledge and skill
enabling that person to correctly perform the task required."
LOW VOLTAGE ( LV )
All Low Voltage work ( > 50V AC > 60V or 120V DC ) should be undertaken in accordance with the regulatory
requirements of the country..
Page 8
INSTALLATION CHECKLIST
PV ARRAY
PV Array orientation
....
BATTERY INSTALLATION
Wiring is protected from mechanical damage
The batteries are installed in a
dedicated battery room, enclosure or
restricted access area
SAFETY
Battery warning sign
" DANGER - Risk of Battery Explosion "
is permanently fixed outside the battery room
/ enclosure in a prominent position
AUTHORISATION :
I,
Location of system
Signed ..
Date :
Page 9
Direct current
Alternating current
Australia Standard/New Zealand Standard
Underwriters Laboratory
International Code Council
National fire Protection Association
American Society of Civil Engineers
Institute of Electrical and Electronics Engineers
Watt hours
Kilowatt hours
Watts
Watts peak
hours
Volts
Amps
Volt amps
Amp hours
Photovoltaic
Peak sun hours ( kWh/m2)
Kilowatt hours/metres squared
Open circuit voltage (volts)
Maximum power point voltage (volts)
Short circuit current (amps)
Maximum power point current (amps)
Low Voltage (>=120V DC in Australian Standards)
Extra Low Voltage (<120V DC in Australian Standards)
Ultraviolet light
High Rupturing Capacity
Current Carrying Capacity
Voltage drop
Cross Sectional Area of cable (mm2)
Copper
Circuit breaker
Page 10