BMCP Unit-1
BMCP Unit-1
LECTURE NOTES ON
BUILDING MATERIALS,CONSTRUCTION PLANNING
Quarrying of Stones
Selection of
a site for quarrying
Stone quarrying tools
Methods of
quarrying
Blasting
BRICKS
building
known as
Typical Plug Drills - (Top) drill with a round blade (bottom) drill with pointed blade
The plug & feather method involves drilling a series of round holes in the rock spaced every six inches or
so apart. The typical round hole ranges for 1/2 inch to 1 inch in diameter and 3 to 4 inches deep. These
holes are drilled using either a single bladed plug drill or a star drill. The drill is struck by a hammer. The
stone dust which accumulates in the holes is removed using a simple tool called a scrapping spoon. Once
the holes are drilled, two shims called feathers or half-rounds are placed in the hole and a wedge called a
plug is placed between the two feathers.
Scrapping spoon
METHODS OF QUARRYING: The purpose of quarrying is to obtain building stones for various
engineering purposes. Depending upon the nature of rocks and the purpose for which stones are needed,
quarrying is done by adopting the following methods:
Quarrying is carried out by employing hand tools for digging / excavation, Heating, Wedging and
Blasting.
1. Digging / excavation: In this method, the stones are merely excavated with the help of suitable hand
tools such as Pick axes, Hammers, Spades, Chisels. This method is useful when soft stones occur in the
form of small blocks.
2. Heating: In this method, the surface of rock is heated by placing pieces of wood or by piling a heap of
fuel over the surface and fired for a few hours. Due to unequal expansion, the upper layer of rock
separates out. The detached portion of rock is then removed by suitable hand tools.
This method is suitable when the rock formation consists of horizontal layers of shallow depth.
Sometimes, intermediate layers are to be separated from the top and bottom layers. In such a case, the
intermediate layer is heated and the expansion separates it from the other two.
3. Wedging: This method of quarrying is usually adopted for rocks such as Sandstone, Limestone, Marble,
Slate, Laterite etc.. About 10 15 cm deep holes, at around 10 cm spacing are made vertically in the rock.
Steel Pins and Wedges or Plugs are inserted in them. These plugs are then struck simultaneously with
sledge hammer. The rock splits along the lines of least resistance through the holes.
4.Blasting:
In this method, the explosives are used to convert rocks into small
pieces of
stones and the main purpose of quarrying stones by blasting is to loosen
large masses of rocks. Explosives such as Gun powder (Blasting powder), Dynamite, (Gelatin),
Detonators, Fuse coil etc. are used.
The blasting powder and dynamite are commonly used as the explosives. The blasting powder is also
known as the Gun Powder which is a mixture of charcoal, salt petre (KNO3) and sulphur.
Fuses: It is required to ignite the explosives. It is in the form of a small rope of cotton coated with tar and
with a core of continuous thread of fine gun powder. The rate of burning of a good fuse is about 10 mm
per second.
Gun cotton: The clean cotton is saturated in a mixture of nitric acid and sulphuric acid. It is pressed into
blocks or sticks while it is wet. It is as strong as dynamite. But its shattering power is less.
Liquid Oxygen: It is oxygen in liquid state. It is stored in a special container. It is comparatively cheap and
used for blasting on a large scale for mining operations.
UNIT-1
Blasting Powder
Large blocks of stones
are obtained
Cheap
Destructive power
weak
Efficiency
Use
0.40 m3
Used for ordinary type
of quarrying work
Dynamite
Small blocks of
stones are
obtained
High cost and is about 5 times than
that of blasting powder
Very strong and 6 times than that of
blasting powder.
0.60 m3
Used for tunneling and mining
operations
PRECAUTIONS IN BLASTING:
Blasting should not be carried out in late evening or early morning hours
A siren should warn the work men and nearby public to maintain a safe distance.
The danger zone, an area of about 200 mts radius should be marked with
red flags.
First aid should be available
The number of charges exploded and the misfires should be recorded
Explosives should be stored and handled carefully.
Detonators and explosives should not
be kept together
STORAGE OF EXPLOSIVES:
BMCP NOTES
UNIT-1
UNIT-1
Porosity
1.5
%
4
%
5-10 %
20-30%
Rock
Only Gravel
Only Sand
Only Clay
Porosity
25
%
35
%
45
%
Permeability : The permeability of a rock or soil defines its ability to transmit a fluid or water .
Permeability depends on the porosity and interconnected pores character of the rock, thus more porous
rocks are more permeable too. (not always). Permeability in a rock is measured in darcies ( 1 darcy =
0.987 m2 square micrometer ).
Eg: 1.Shales are highly porous but less permeable because of fine grained nature which does not
allow water to pass through the rock due to less interconnected pores.
Eg: 2. Vesicular basalts are highly porous but less permeable because the vesicles in them are not
interconnected (i.e., the effective porosity is less).
Crushing Strength: For a good stone, the crushing strength should be greater than 100 Newtons / mm2 .
The approximate value of crushing strength of some of the stones are:
Rock type
Igneous
Sedimentary
Metamorphic
Building Stone
Basalt
Diorite
Granite
Syenite
Limestone
Sandstone
Shale
Gneiss
Slate
S No
1
2
3
4
5
6
7
8
9
BMCP NOTES
UNIT-1
UNIT-1
Appearance: The stones which are to be used for face work should be decent in appearance and capable
of preserving their color uniformly for a long time. It is desirable to prefer light colored stones as
compared to dark coloured stones because there are chances of the latter variety to be attacked easily by
weathering agents.
Durability: A good building stone should be durable. The various factors such as Chemical composition;
Resistance to atmospheric conditions etc influence the durability of a stone. Following are the
important atmospheric agencies which affect the durability of a stone.
a)
b)
c)
d)
e)
Co-efficient of Hardness: The co-efficient of hardness, as worked out in hardness test should be greater
than 17 for a stone to be used in road work. If it is between 14 and 17, and < 14, the stone is said to be
medium and poor hardness respectively and such stone should not be used in road works.
Specific gravity: For a good building stone, the specific gravity should be
greater
than 2.7 The
heavy varieties of stones with more compact and less
porous can be used
for various engineering applications such as dams, weirs,
retaining walls, docks etc.. On the other hand, the lighter varieties of stones are to be used for domes, roof
coverings etc..
Texture: A building stone should have compact, fine crystalline nature, free from cavities, cracks, loose
material, softness etc..
Toughness Index: In impact test, if the value of
toughness index comes below
13, the stone is not tough. If it comes between 13
and 19, the stone is said to
be moderately tough. If it exceeds 19, the toughness of stone is said to be high.
Water Absorption
water. It is expressed as % in weight
M1 M
V
Ww =
BMCP NOTES
UNIT-1
UNIT-1
Weathering: A building stone should be capable of with standing adverse effects of various atmospheric
and external agencies such as rain, frost, wind etc..
Density ( p) is the mass of a unit volume of homogeneous material denoted by: p= M / V ( g/cm3) where
M = mass (g) and V = volume (cm3).
Bulk density ( pb)
BMCP NOTES
UNIT-1
UNIT-1
ARTIFICIAL STONES: Where durable natural stone is not available at reasonable cost, artificial stone,
also known as CAST STONE becomes the choice. Artificial stone is made with cement and natural
aggregates (crushed stone) and sand with desired surface finish. Suitable color pigments may be added.
Following procedure is generally adopted in making an artificial stone:
A mixture of 1 parts of stones of size 36 mm; 1 parts of stones of size < 3mm and 1 part of
cement by volume is prepared.
The necessary pigment is added to produce the desired color effect to the above mixture.
Required quantity of water is added and thorough mixing is done.
The mixture thus prepared is transferred to special moulds.
The mixture is allowed to harden and its surface is kept wet.
The artificial stone is then ready in block form.
Polishing can be done if required.
FORMS OF ARTIFICIAL STONES:
Cement Concrete: This is a mixture of cement, fine aggregate, coarse aggregate and water. If steel is used
with cement concrete, it is known as the Reinforced Cement Concrete ( RCC). Concrete blocks are used in
construction of piers, steps, window sills etc
UNIT-1
Mosaic Tiles: The pre-cast concrete tiles with marble chips at top surface are known as the mosaic tiles.
Terrazzo: This is a mixture of marble chips and cement. It is used for bath rooms, residential buildings,
temples etc
Victoria Stones are granite pieces with the surfaces hardened by immersing in soda silicate for about
two months.
Ramsom Stones are prepared by mixing soda silicate with cement to provide decorative flooring. These
are also known as chemical stones. These have compressive strength of about 32 N / mm2.
BRICKS
The common brick is one of the oldest building material and it is extensively used at present as a leading
material in construction because of its durability, strength, reliability, low cost, easy availability, easy to
handle etc.. Bricks are used for building up exterior and interior walls, partitions, footings and other load
bearing structures.
The Great Wall of China (210 BC) was built with bricks. The other examples of the use of bricks in early
stage of civilization could be in Rome. A number of country farm houses still exist in Great Britain and
profess to be the monuments of the excellent hand made bricks.
A brick is rectangular in shape and of size that can be conveniently handled with one hand. Bricks may be
made of burnt clay or mixture of sand and lime (or) of Portland cement concrete.
Size of a standard brick (modular brick) should be 19 x 9 x 9 cm. However, the bricks available in most
part of the country still are 9 x 4 x 3 and are known as field bricks. Weight of such a brick is 3.0 kg.
At places where stones are not easily available but where there is plenty
of clay, brickwork becomes cheaper than stonework.
The cost of construction works out to be less in case of
brickwork than
stonework as less skilled labour is required in the construction of
brickwork.
No lifting devices are necessary to carry bricks as they
can be easily
moved by manual labour.
The bricks resist various atmospheric effects better than stones.
In case of brickwork, the mortar joints are thin and hence the structure becomes more durable.
It is easy to construct connections and openings in case of brickwork than stonework.
CHARACTERISTICS OF GOOD BRICK: The essential requirements for building bricks are
sufficient strength in crushing, regularity in size, and a pleasing appearance when exposed to view.
Size and shape: The bricks should have uniform in size, rectangular surfaces with parallel sides and sharp
straight edges.
Color: The brick should have a uniform deep red (or) cherry colour as indicative of uniformity in
chemical composition and thoroughness in the burning of the brick.
Texture and compactness: The surfaces should not be too smooth to cause slipping of mortar. The brick
should have uniform texture and should not show fissures, holes etc..
Hardness and soundness: The brick should be so hard that when scratched by
a finger nail no impression is made. When two bricks
are struck together, a
metallic sound should be produced.
Water Absorption should not exceed 20% of its dry weight
in water for 24 hours to 48 hours.
Silica
Alumina
Calcium
Mg
Ferric Oxide
Alkalis
SO3; H2O
50 60 %
20 30 %
10 %
<1%
< 7 % < 20 %
< 10 %
<2%
Silica: A good brick earth should contain about 50% to 60% of silica. The presence of silica constituent
prevents cracking, shrinking in bricks thus imparts uniform shape to the bricks. Excess of silica makes the
brick brittle and weak on burning. The durability of bricks depends on the proper proportion of silica in
brick earth.
Alumina:
A good
brick earth
should contain
about 20 to 30% of
alumina is
present
in excess,
with inadequate
quantity of sand the
shrink and it produces cracks during drying and burning and become too hard when burnt.
alumina. If
raw bricks
Lime ( calcium ) : A small quantity of lime not exceeding 10% is desirable in good brick earth. The
excess of lime causes the brick to melt and hence its shape is lost and also results in splitting of bricks into
pieces.
Magnesia if exceeds 1%, affects the color and makes the brick yellow. Excess of magnesia content leads
to the decay of bricks.
Iron oxide usually constitutes < 7% . If it exceeds 7%, the brick becomes dark blue. When excess of
oxygen is available, the bricks becomes dark brown or black color on burning.
HARMFUL SUBSTANCES IN BRICK EARTH: Following are the ingredients which are undesirable
in the brick earth:
LIME: When lime is present in lumps, it absorbs moisture, swells and causes disintegration of the bricks.
PEBBLES, GRAVELS: The presence of pebbles of any kind is undesirable in brick earth because it will
not allow the clay to be mixed uniformly and thoroughly which will result in weak and porous bricks.
Also the brick containing pebbles will not break regularly as desired.
ALKALIES: These are mainly in the form of soda and potash. When alkalies present in excess, the
bricks become unsymmetrical / loose their shape. Further, the presence of excess alkalies content absorb
moisture from the atmosphere.
Such moisture, when evaporated, leaves behind grey or white deposits on the wall surface and the
appearance of the building as a whole is then seriously spoiled.
UNIT-1
ORGANIC MATTER: The presence of organic matter in the brick earth, which is not burnt in case, the
bricks become porous and the strength is reduced.
SULPHUR & CARBON: Sulphur is usually found in clay as the sulphates of Calcium ( CaSO4);
magnesium (MgSO4); Sodium (NaSO4); Potassium (K2SO4) and iron sulphides ( FeS2). If, however,
there is carbon in the clay and insufficient time is given during burning for proper oxidation of carbon and
sulphur, the latter will cause the formation of a spongy, swollen structure in the brick.
MANUFACTURING OF BRICKS
In the process of manufacturing of bricks, the following four distinct operations are involved: 1.
Preparation of clay / Brick earth
2. Moulding
3. Drying
4. Burning
1.PREPARATION OF CLAY / BRICK EARTH consists of the following operations:
a) Un-soiling: The soil used for making building bricks should be processed and to be free from gravel,
sand ( > 2 mm ); lime and kankar particles, organic matter etc. About 200 mm of the top layer of the earth,
normally containing stones,
pebbles, gravels, plant roots
etc is
removed
after
clearing the trees and
vegetation.
b) Digging: The clay
is then
dug out from the
ground. The height of
heaps of clay on the ground is
mm. The digging operation should be done before rains.
ground and
about
is spread on the
600 mm to 1200
c)weathering: The clay/soil is left in heaps and exposed to weather for atleast one month. The soil should
be turned over at least twice and it should be ensured that the entire soil is wet throughout the period of
weathering.
In order to keep it wet, water may be sprayed as often as necessary. The plasticity and strength of the clay
are improved by exposing the clay to weather.
d) Blending: The clay / soil is then
mixed with
sand and calcareous earth in
suitable proportions to modify the
composition
of soil uniformly with spades.
Addition of water to the soil at the dumps is necessary for easy mixing and workability. However, the
excessive moisture content may affect the size and shape of the finished brick. The blending makes clay
fit for the next stage of tempering.
process of tempering,
the
The tempering
should
be
clay of uniform
character.
e) Tempering: In the
degree of hardness.
homogeneous mass of
Pug Mill
2.MOULDING: It is a process of giving a required shape to the brick from the prepared clay / soil / brick
earth. Moulding may be carried out by hand or by machines.
Hand Moulding: In this process, the bricks are moulded by hand ie manually. It is adopted where man
power is cheap and for producing a small quantity of bricks. A typical wooden mould should be prepared
from well seasoned wood for making bricks.
The longer sides are kept slightly projecting to serve as handles. The strips of brass or steel are sometimes
fixed on the edges of wooden moulds to make them more durable.
The steel mould even be prepared from steel angles and plates. The thickness of steel mould is generally 6
mm.
The bricks prepared by hand moulding are of two types:
(a) Ground - moulded bricks
the corners
edged metal
drying. The
UNIT-1
Table Moulding: the process of moulding these bricks is just similar to ground moulding. But in this
process, the clay, mould, water pots, strikes, pallet boards are placed on the table. A thin board called
pallet is placed over the mould. The bricks are moulded on the table and sent for the further process of
drying. The cost of brick moulding also increases slightly when table moulding is adopted.
Machine Moulding: The moulding may also be achieved by machines. It proves to be economical when
bricks in huge quantity are to be manufactured at the same spot in a short time. Machine moulding can be
done by either of the following process:
Plastic method ( Plastic Clay Machine ): The pugged clay is placed in the machine through a rectangular
opening by means of an auger. Clay comes out of the opening in the form of a bar. The bricks are cut from
the bar by a frame consisting of several wires at a distance of brick size and this is a quick and economical
process. This process is also known as WIRE CUT BRICKS.
Dry Press Method / Dry Clay Method: In these machines, the strong clay is first converted into powder
form. A small quantity of water is added to form a stiff plastic paste. Such paste is placed in mould and
pressed by machine to form hard and well shaped bricks. These bricks are also known as PRESSED
BRICKS. They can be sent directly for the next process of burning.
3.DRYING: For drying, the bricks are laid longitudinally in stacks. The bricks in stakes should be
arranged in such a way that sufficient air space is left between them. The bricks should be allowed to dry
till they become hard or the moisture content is brought down to about 3% under exposed conditions
within 3 to 4 days.
For the drying purpose, Drying yards should be prepared. The Drying yards should be slightly on a higher
level and it is desirable to cover it with sand. Such an arrangement would prevent the accumulation of rain
water.
4. BURNING: This is a very important operation in the manufacture of bricks. The burning of clay may
be divided into three main stages.
Dehydration stage ( 400 650oC): This is also known as water smoking stage. During dehydration :
The water which has been retained in the pores of the clay after drying is driven off;
INTERMITTENT KILN
The production
of bricks
is 2 3 lakhs and the process is
months. This process yields about 60% first class bricks.
Kiln burning:
A kiln is
a large oven which is used to burn bricks.
used for burning bricks may be underground ( Bulls Trench Kiln )
( eg: Hoffmans
Kiln). The Kilns may be rectangular, circular or oval
The Kilns are of two types: (i) Intermittent Kilns (ii) Continuous kilns.
INTERMITTENT KILNS:
The process
of burning bricks is
hence , the kiln
is known as intermittent
kiln which means that
fired, cooled and unloaded and then the next loading is done. Since the walls
BMCP NOTES
UNIT-1
completed in 6
The Kiln
or over ground
in shape.
discontinuous and
they are loaded,
CLAMP
UNIT-1
and sides get cooled during reloading and are to be heated again during next firing, there is wastage of
fuel. . They may be over ground or underground.
Fly ash Bricks: Fly ash bricks are masonry units that are used in the construction of buildings. They are
considered to be a part of good and affordable building materials. They contain Class C fly ash and water.
Fly ash bricks are made by compressing Class C fly ash and water at 4000psi and then curing is carried on
for 24 hours at a temperature of 66 degrees Celsius steam bath. Air entrainment agent is used to toughen
the bricks.
GREEN BRICKS: The bricks are used like conventional clay bricks for building things from houses to
factories. Theyre called green because they are built from a toxic byproduct produced from coal-burning
power plants. Instead of these toxins being released into the environment, or disposed of through costly
means, theyre pumped into the bricks.
The waste product is called fly ash. Its loaded with mercury, lead, and other toxic chemicals. Coalburning power plants spend millions of dollars to dispose of the powdery byproduct. Until now, the
estimated 70 million tons of byproduct has been buried in specially designed ponds and waste centers.
GREEN BRICKS
UNIT-1
HOFFMANS KILN
TUNNEL KILN: A tunnel kiln useful for burning vertically perforated green bricks, includes a furnace
chamber; tubular burners for heating the furnace chamber and a transport device for transporting green
bricks in raster-like spaced-apart relationship in a travel direction through the furnace chamber that the
perforations of the green bricks are oriented in a common direction.
TUNNEL KILN
Bull's Trench Kilns: In India, brick making is typically a manual process. The most common type of
brick kiln in use there are Bull's Trench Kiln (BTK), based on a design developed by British engineer W.
Bull in the late 19th century. An oval or circular trench, 69 meters wide, 2-2.5 meters deep, and 100150
meters in circumference, is dug. A tall exhaust chimney is constructed in the centre. Half or more of the
trench is filled with "green" (unfired) bricks which are stacked in an open lattice pattern to allow airflow.
The lattice is capped with a roofing layer of finished brick.
BMCP NOTES
UNIT-1
UNIT-1
In operation, new green bricks, along with roofing bricks, are stacked at one end of the brick pile; cooled
finished bricks are removed from the other end for transport. In the middle the brick workers create a
firing zone by dropping fuel (coal, wood, oil, debris, and so on.) through access holes in the roof above
the trench.
The advantage of the BTK design is a much greater energy efficiency compared with clamp or scove
kilns. Sheet metal or boards are used to route the airflow through the brick lattice so that fresh air flows
first through the recently burned bricks, heating the air, then through the active burning zone. The air
continues through the green brick zone (pre-heating and drying them), and finally out the chimney where
the rising gases create suction which pulls air through the system. The reuse of heated air yields savings in
fuel cost.
A half dozen laborers working around the clock can fire approximately 15,000-25,000 bricks a day. In the
BTK process the bricks do not move. Instead, the locations at which the bricks are loaded, fired, and
unloaded gradually rotate through the trench.
TESTS FOR BRICKS: A brick is generally subjected to the following tests to find out its suitability for
the construction work:
Water Absorption Test ( US 3495):: A brick is taken and it is weighed dry. It is then immersed in water
for a period of 24 to 48 hours. It is weighed again and the difference in weight indicates the amount of
water absorbed by the brick. It should not, in any case, exceed 5%-20% of weight of dry brick.
Compressive Strength Test ( IS: 3495): The crushing strength of a brick is find out by placing in a
compression testing machine. It is pressed till it breaks. The minimum crushing or compressive strength
of bricks is 3.50 N / mm2.
Efflorescence Test: The brick is immersed in water
for 24 hours. It is then
taken out and allowed to dry in shade.
The absence of grey or
white deposits
on its surface indicates the absence of
soluble salts. If
the white
deposits cover
about 10% surface, the efflorescence is said to be slight and it is considered as moderate when the white
deposits cover about 50 % of surface. If grey or white deposits are found on more than 50 % of surface,
the efflorescence becomes heavy and it is treated as serious.
In this
bricks
Soundness:
other. The
produced.
BMCP NOTES
UNIT-1
UNIT-1
DIFFERENT FORMS OF BRICKS: Various forms of bricks are used depending upon the places of
use. For eg:
Used to construct open drains
A brick moulded with a rounded
angle. A connection which is
formed when a wall takes a turn is
known as Quoin.
Cornice brick
Used
view
It is
used in
lining
furnaces,
kilns, fireboxes,
and fireplaces.
A
refractory brick is
built primarily
to
withstand high temperature.
Coping bricks
Perforated bricks
Hollow bricks
BMCP NOTES
for architectural
point
of
frog
Gun powder
Magazine
Masonry
Metamorphism
Mortar
Pallet
Pugging
Strike
Weathering
providing
frog is to form
a key for
the bricks
A mixture of
charcoal,
salt petre (KNO3) and sulphur and
the proportions by weight
are 15, 75 and 10 respectively.
A special
type of
building meant for storing the explosives.
Masonry may be defined as the construction of building
units (such as
stones, bricks / precast blocks of
concrete)
bonded together with mortar.
The process
by which the changes
are brought in
solid
rocks by the agencies of temperature, pressure and
chemical
active
solutions which in
turn establish a
new
equilibrium.
Mortar is a homogeneous mixture produced by uniform
mixing of cement or lime or combination of these two in
addition to sand and water to make a paste of required
consistency.
A thin board called pallet is placed over the mould
the process of grinding clay with
water
and making it
plastic is known as the Pugging.
The extra or surplus clay is removed with a sharp edged
metal plate called STRIKE
which is
a
natural
process
of disintegration
and
decomposition
1
Babylonians were perhaps the first to use clay as cementing material. In ancient times stones have
been invariably used as a construction material with lime as
the binder for construction of forts and
defense
used lime and gypsum
as cementing materials in
structures.
Egyptians have
the famous Pyramids.
cement is
Page
Ingredient
Range
Lime
Oxide /
composition
CaO
62
60 65
Silica
Alumina
SiO2
Al2O3
22
5
17 25
38
Calcium
sulphate
CaSO4
34
Iron oxide
Fe2O3
0.5 6
Magnesia
MgO
0.5 4
Alkalies
(Na2O+K2O )
0.1 0.4
Function
Controls strength and soundness. Its
deficiency reduces strength & setting time
Imparts strength. Excess cause slow setting
Responsible for quick setting,
if in excess,
it lowers the strength / weakness the cement
A small amount of sulphur is useful in
making sound cement. If it is in excess ,
it causes cement to become unsound.
Gives colour, hardness & strength to the
cement
Gives color, hardness. If in excess, it
causes cracks in mortar.
These are residues and if
cause efflorescence and cracking
in excess
Cement
Cement Concrete for laying floors, roofs, lintels, beams, stairs, pillars etc
Construction of important engineering structures such as Bridges, Culverts, Dams,
Tunnels, storage Reservoirs; Docks etc
Making Cement Pipes
Manufacture of precast pipes, dust bins, fencing posts etc..
22
33
33
43
37
53
Page
clay
are first
passed over
fine
powder
mixed
Bins
The product
obtained after calcination at a temperature of about 1400 1500o C
in rotary kiln is called
CLINKER.
The clinker is cooled rapidly to preserve the metastable compounds and then ground in Tube Mills
where 2 3 % of gypsum is added. The purpose of adding gypsum is to retard the setting of cement.
Generally, cement is stored in bags of 50 kg.
Page
BMCP NOTES
1
1
The crushed raw materials are fed into ball mill and
to make
a thick paste. This paste, usually contain about
dried and
made ready for the feed of rotary kiln where it
BMCP NOTES
composition
fuel.
the
the
Page
During
the operation of
ball mill;
the
steel balls
in it
pulverize the
raw
materials which form
a slurry with water. This slurry is passed to silos (storage
tanks), where the proportioning of the compounds is adjusted to ensure desired chemical composition.
Type of
no
cement
1
2
3
4
5
6
7
8
9
Soundness by
Compressive strength
(MPa) or N/mm2
Grade
OPC
OPC
OPC
SRC
PPC
RHC
HAC
SSC
LHC
33
43
53
Le Chatelier (mm)
10
10
10
10
10
10
5
5
10
Autoclave (%)
0.8
0.8
0.8
0.8
0.8
0.8
NS
NS
0.8
3 days
16
23
27
10
16
27
35
15
10
7 days
22
33
37
16
22
NS
NS
22
16
28 days
33
43
53
33
33
NS
NS
30
35
Fineness
(m2/Kg)
225
225
225
225
225
300
325
225
400
320
Page
POP powder is mixed with water to form a paste which releases heat and then hardens once dried
under normal temperature. Unlike mortar and cement, plaster remains quite soft after drying, and can
be easily rubbed or scratched with metal tools or even sandpaper. On heating, further upto a
temperature of about 20oC, the entire water is driven off and the resulting product is known as the
Gypsum Anhydrite.
BMCP NOTES
Soundness
Strength:
Consistency Test and
Fineness.
SOUNDNESS: Soundness refers to the ability of a hardened cement paste to retain its volume after
setting without delayed destructive expansion. This destructive expansion is caused by excessive
amount of CaO or MgO. In other words, the purpose of this test is to detect the presence of
uncombined lime in cement. This may happen due to over burning of ingredients of cement in kilns.
So it is an important test to assure the quality of cement since an unsound cement produces cracks,
disintegration and leading to failure finally.
Soundness of cement may be tested by Le-Chatelier method or by authoclave method.
STRENGTH: Cement is tested for Compressive and Tensile strength because the cement hydrates
when water is added to it. So, the strength of mortar and concrete depends upon the type and nature of
cement.
Page
Hydration of cement: The chemi ca l r eact i on bet ween c ement and wat er i s known as hydration
of cement
BMCP NOTES
1
Compressive Strength.: Compressive Strength is the basic data required for mix design. By this test,
the quality and quantity of concrete can be controlled and the degree of adulteration is checked.
The compressive strength at the end of 3 days, 7 days and 28 days are given in table and the results are
expressed in N/mm2
Tensile Strength: Tensile Strength may be determined by Briquette Test method or by Split Tensile
Strength Test.
The Tensile strength of cement affords quicker indications of defects in the cement. However, the test
is also used for the determination of rapid hardening cement. The tensile strength at the end of 3 days
and 7 days for OPC is 2.0 N / mm2 and 2.5 N/ mm2 respectively.
( 2.0 N / mm2 = 20 kg / cm2 ) ( 2.5 N/ mm2 = 25 Kg / cm2 )
Consistency Test: This is a test to estimate the quantity of mixing water to form a paste of normal
consistency.
Page
BMCP NOTES
1
FINENESS: This test is carried out to check proper grinding of cement. In other words, the degree of
fineness of cement is the measure of the mean size of the grains in it.
There are 3 methods for testing fineness:
SIEVE METHOD: 100 gms of cement sample is taken and air set lumps if any, in the sample are
broken with fingers. The sample is placed on a 90 micron sieve and continuously sieved for 15
minitues. The residue should not exceed the limits specified below:
OPC
10% of residue by weight
RHC
5% of residue by weight
PPC
5% of residue by weight
Air Permeability method: In this process, a cement sample of 20 mm height is placed in the Lea and
Nurse apparatus and air pressure is applied. A manometer is connected to the top and bottom of the
permeability apparatus and the pressure is so adjusted.
The specific surface (Surface area is the measure of how much exposed area a solid object has,
expressed in square units ) for various cements should be as specified in table:
Type
of
cement
OPC
RHC
LHC
PPC
HAC
SSC
Specific
surface not
less than
cm2/gms
2250
3250
3250
3000
2250
4000
Page
BMCP NOTES
1
Wagner Turbidimetre method: This method is to be adopted to estimate the surface area of one gram
of cement. The cement is dispersed uniformly in a
rectangular glass tank
filled with kerosene.
Then,
parallel light rays
are
passed through the
solution which strike
the
sensitivity plate of
a
photoelectric cell. The turbidity of the solution at a given instant is measured by taking readings of the
current generated by the cell.
By recording the readings at regular intervals while the particles are falling in the solution, it is
possible to secure information regarding the grading in surface area and in size of particle. Readings
are expressed in sq cm per gms.
ADMIXTURES: Admixture is defined as a material, other than water, aggregates, cement, that is
added to the concrete immediately before or during mixing. Admixtures change properties of the
concrete in colour, curing time, temperature range and setting time.
Concrete is being used for wide varieties of purposes to make it suitable in different conditions.
Ordinary concrete may fail to exhibit the required quality performance or durability under different
conditions. In such cases, admixture is used to modify the properties of ordinary concrete so as to
make it more suitable for any situation.
Plasticizers and Superplasticizers specifically developed in Japan and Germany around 1950 and later
on they were made popular in USA, Europe and Middle East. Unfortunately, the use of plasticizers
and Superplasticizers have not become popular in India till recently ( 1985).
Plasticizers (Water Reducers): Concrete in different situations requires different degree of
workability. A high degree of workability is required in case of beams, columns, beam junctions,
pumping of concrete for considerable distances. One must remember that addition of excess water,
will only improve the fluidity or the consistency but not the workability of concrete.
The easy method generally
followed at the site in most of the conditions
is
to use extra water
to overcome different
situations which
is unengineering
practice.
Today, the
use of plasticizers
help the difficult
conditions
for
obtaining higher workability without using excess of water.
Page
BMCP NOTES
Superplasticizers constitute
Superplasticizers (High Range Water Reducers ):
a relatively new category and improved
version of
plasticizer, the use of which
was developed in Japan and Germany
during 1960 and 1970 respectively.
Use of Superplasticizers permit the reduction of water to the extent upto 30% without reducing the
workability. The use of superplasticizer is practiced for the production of high strength and high
performance concrete. Superplasticizers can produce same w/c (water cement ratio); same
workability; increased strength, homogeneous character etc.
Retarders: A retarder is an admixture that slows down the chemical process of hydration so that
concrete remains plasticity and workable for a longer time. The retarders are used in casting purposes.
These are also used in grouting
oil wells. Oil wells are
sometimes taken upto
a
depth of about 6000 meter
o
deep where the temperature may be about 200 C.
The spacing
between the
steel tube and the wall
of the
well are to be sealed with cement
grout and
to prevent the entry of
gas or
oil into other
rock formations.
For
all these
works cement grout is required to be in mobile condition for about 3 to 4 hours even at that high
temperature without getting set.
Accelerators: These admixtures are added to increase the rate of strength of concrete and to reduce
the required period of curing. In the past one of the commonly used materials as an accelerator was
calcium chloride. The recent studies have shown that calcium chloride is harmful for reinforce
concrete.
Air entraining Admixtures: Air entrained concrete is made by mixing a small quantity of air
entraining agents. These agents modify the properties of concrete regarding workability, segregation,
finishing quality of concrete. Air entraining admixture is used to prevent frost scaling in concrete.
The following types of air entraining agents are used for making concrete:
Natural wood resins
Animal or vegetable fats and oils such as olive oil, stearic acid; oleic acid.
Various wetting agents such as alkali salts
Miscellaneous materials such as the sodium salts of petroleum sulphonic acids, hydrogen
peroxide and aluminium powder
The common air entraining agents are
Teepol, Petrosan, Cheecol etc.. Air entrained
construction of Hirakud dam, Koyna dam,
Vinsol
Orvus,
in the
etc.
Page
Chemical admixtures: Chemical admixtures are added to concrete in very small amounts mainly for
reduction of water content or control of setting time.
BMCP NOTES
1
Mineral admixtures: Mineral admixtures (puzzolanic materials) are usually added to concrete in
larger amounts to enhance the workability of fresh concrete; to improve resistance of concrete.
The term Puzzolana is derived from Pozzuoli, a town in Italy. The sand (volcanic dust) around this
town, when mixed with hydrated lime was found to possess cementious properties. Puzzolanic
materials can be divided into two groups such as:
Natural Puzzolanas viz clay, shales, cherts, volcanic tuff which needs further grinding and sometimes
needs calcining to activate them to show puzzolanic properties.
Artificial Puzzolanas include Fly ash, Blast Furnace Slag, Silica fumes.
USES: A proper use of admixtures offers certain beneficial effects to concrete, including improved
quality, acceleration or retardation of setting time, enhanced frost and sulfate resistance, control of
strength development, improved workability, and enhanced finishability.
Blast Furnace Slag consisting essentially of silicates and aluminates of calcium. The granulated
material when further ground to less than 45 microns will have specific surface of about 400-600
m2/kg. The chemical composition of BFS is similar to that of cement clinker.
1
1
FORMWORK MATERIALS:
Timber is the most common material used for form work. When the form work is to be used for
small works only a few times, then timber proves to be more economical than steel or aluminium.
Advantages: Formwork material of timber is
easily available
formwork material can be made to desired shape
can be made to required size
easy to carry
economically viable and cheap
convenient for small works
Disadvantages:
possibility of warping, swelling and shrinkage of timber. However, those effects can be
overcome by applying shuttering oil as coating. This coating prevents the material from
adhering to concrete and hence the stripping (removing of formwork material) makes
easier.
1
1
Steel/Aluminium formwork: If the formwork is desired to be re-used several times, then the use
of steel or aluminium is preferred. Though the initial cost of steel is very high but for large works
with many repetitions, the steel form work proves to be economical. In case of specific structures,
such as round columns, curved surfaces, tunnels etc the use of steel form work should be made.
Steel form work has many advantages such as
Requirements for a Form work: A good form work should satisfy the following requirements:
The material of the formwork should be cheap and it should be suitable for re-use several
times.
It should be water proof so that it doesnt absorb water from concrete.
Shrinkage and swelling of material should be minimum.
It should be strong enough to withstand all loads coming on it such as dead load of
concrete, live load of concrete during its pouring, compaction and curing of concrete.
The surface of the form work material should be smooth and should afford easy stripping.
All joints of the form work should be stiff so that lateral deformation under loads is
minimized.
Column boxes
1
1
SCAFFOLDING
The Scaffolding is a temporary frame work of timber or steel components having platforms at
different levels, to enable the masons to work at different heights of a buildings. When the height
of wall or column or other structure of a building exceeds about 1.5 mts (4), temporary structures
are used to support the platform over which the work men can sit and carry the activities. These
temporary structures constructed are very close to the wall, is in the form of timber or steel frame
work, commonly called scaffolding.
Scaffolding materials is needed for the repairs or even demolition of a building. In addition,
surface finishing such as plastering, pointing, white washing or distempering of walls, columns
etc at higher levels can also be carried out. The scaffolding should be stable and be strong enough
to support work men and other construction material placed on the platform. The height of the
scaffolding goes on increasing as the height of construction increases.
Components of Scaffolding:
Standards: These are the vertical members of the frame work supported on the ground or
embedded into the ground.
Ledgers: These are horizontal members, running parallel to the wall,
Braces: These are diagonal members fixed on standards.
Putlogs: These are transverse members, placed at right angles to the wall with one end supported
on ledgers and other end on the wall.
Transoms: These are those putlogs whose both ends are supported on ledgers.
Boardings: These are horizontal platform to support workmen and material and are supported on
the putlogs.
Various components or members of the scaffolding are secured by means of rope lashings, nails,
bolts etc
1
1
Standards / verticals
Ledgers
Braces to standards
Transoms
Cuplock material
Flathead pin
Shoring frame
H frame
Props
1
1
Boarding
Braces
Adj stirupps
TYPES OF SCAFFODING:
Double scaffolding/ Masons Scaffolding: This type of scaffolding is stronger than the
single scaffolding and is used in the constructions of stone work. The form work is similar to the
single scaffolding except two rows of standards are used, one row close to the wall within 15 cm
and the other at 1.2 to 1.5 m away from the face of the wall. The put logs are supported at both
ends on ledgers. Sometimes, in addition to the diagonal braces, inclined supports called Racking
shores are provided to prevent the slipping of scaffold away from the wall.
Double/Masons
Double/Masons
scaffolding (wood)
scaffolding (steel)
3.
Cantilever Scaffolding / Needle Scaffolding: This type of scaffolding is
needed under the following circumstances:
In this work, single scaffolding or double scaffolding components are supported by a series of
cantilevers or needle beams (timber beams projecting from wall) passing through window
openings or through holes in the wall.
1
1
4. Suspended scaffolding: This type of scaffolding is suitable for maintenance works such as
painting, pointing, distempering etc. The working platform is suspended from the roofs by means
of wire ropes or chains.. The mechanical arrangements are provided to raise or lower the platform
to attain the optimum level for working.
Cantilever Scaffolding
Trestle scaffolding: The working platform is supported on the top of mobile devices
such as tripods, ladders etc mounted on wheels. Trestle scaffolding is suitable for minor repairs or
painting work upto a maximum height of 5 mts from the supporting level.
Trestle scaffolding
Steel scaffolding
1
1
Patented scaffolding
SHORING
The temporary support provided to an unsafe structure or to a structure under-going alterations is
called a shore, and the method of its construction is called shoring. Shoring can be used in case of
When a wall shows signs of bulging due to improper workmanship which needs
rectification.
Types of shores:
Raking Shores: Rakers of inclined members are used to give lateral support to the wall. Usually
a raking shore consists of the following components:
Wall plates
Needles
Cleats
Bracings
Sole plates
Raking shore
The sole plate should be properly embedded into the ground at an inclination and the sole plate
should be accommodating all the rakers and a cleat provided along the outer edge. However the
rakers should be inclined to the ground by 45 to make them move effective.
Flying or Horizontal Shores: These are used to give horizontal support to two adjacent walls in
which the shores do not reach the ground. If the walls are quite near to each other (distance upto 9
mts), single flying shore can be constructed. It consists of wall plates, needles, cleats, struts,
horizontal / flying shore, folding wedges etc. When the distance between the walls is more, a
composed or double flying shore may be provided.
Flying shores have the advantage that building operations of the ground are not obstructed. Flying
shores are inserted when the old building is being removed, and should be kept in position till the
new unit constructed.
1
Dead or Vertical Shores: These consist of vertical members who support the horizontal
members (needles). The horizontal members transfer the load of the wall to the vertical shores
(vertical members). Such vertical shoring is provided to serve the following purposes.
Holes are made in the wall at suitable heights and the horizontal members, which are made of
thick wooded sections or of steel are inserted in the steel. Each horizontal is supported at its two
ends by vertical ports / dead shores.
The horizontal members are spaced at 1 to 2 mts. A minimum of 3 horizontal shores should be
used for an opening. If the external wall is weak, raking shores may be provided in addition to
vertical shores.
Shores should be removed only when the mew work has gained sufficient strength, but in no case
earlier than 7 days of the completion of new work. An interval of two days should be allowed
between each one of these removal operations.
Flying shore
Dead shoring
1
1
UNDER PINNING: The method of supporting a structure, while strengthening its existing
foundation to take the increased load is called underpinning. Before under pinning shoring may
be done according to the conditions of the structure for its stability. The use of underpinning
becomes essential to meet the following requirements under different situations:
To strengthen the shallow footing of the existing building, when a building with deep
foundation is to be constructed adjoining to it.
Page10
The pit is now excavated upto the desired level of the proposed new foundation . The old
foundation may be extended upto level of new foundation directly or by cutting the lower part of
old footing as desired.
1
1
Pile method: The foundation of piers and columns may be strengthened by providing
underpinning by the Pile method. In this method, the piles are driven along both the sides of the
existing wall and then needles in the form of pipe caps are provided through the existing wall.
Thus existing wall is relieved of the loads coming on it. This method is useful in clayey soils and
for water-logged areas and for walls carrying heavy loads.
In this method, under pining is carried out in two stages.
In stage I, a precast RCC pile is installed by digging an approach pit under the existing wall
foundation. A jack arrangement is set up below the foundation to assess the overload capacity.
All the material surrounding the pile is removed by means of earth augers, water jets. The gap so
formed is filled up with cement concrete to provide firm bearing ground. In stage II, a steel Ibeam is set on and the jacks are then removed.
1
1
Plinth level
at
a
2. Grillage foundations: Grillage foundation is used when heavy structural loads from columns,
piers or stanchions are required to be transferred to a soil of low bearing capacity. Grillage
foundation is often found to be lighter and more economical. This avoids deep excavation.
Depending upon the material used in construction of grillage foundation can be broadly divided
in the following two categories.
Page
4.Stepped foundations:
A foundation constructed in a series of
steps that approximate
the slope of the bearing
stratum.
The
purpose
is
to
avoid horizontal force vectors that might
cause sliding.
5.Inverted arch foundations/ Footing .
It is used to be provided for multi-storeyed
buildings in olden times. However, with the
advent of reinforced cement concrete
construction practice, inverted arch foooting
is rarely done these days. One of the
drawbacks in this type of construction is that
the end piles have to be specially
strengthened by buttresses to avoid the arch
thrust tending to rapture the pier junction.
However, the advantage of inverted arch
construction is that in soft soils the depth of
foundation is greatly reduced
Structural plan of a typical floor: A structural plan of a typical floor contains location,
nomenclature and details of various structural elements at that floor level.
Terrace plan. The terrace plan is the plan at the roof level showing the stair cabin, lift cabin,
overhead water tanks alongwith roof drainage pattern, parapet walls etc.
Classification of buildings: According to National Building code of India 1970, different
classification of buildings on the basis of occupancy are:
Group A Residential Buildings: All those buildings in which sleeping accommodation is
provided for residing permanently or temporarily with or without cooking or dining or both
facilities are termed as residential buildings, for example Apartments, Flats, Bungalows,
Dormitories, Private Houses, Hotels,
Hostels, Cottages, Holiday Campus, Clubs, outhouses, Inns, etc., These buildings are further subdivided in to 5 groups, namely; A- 1 Lodging Houses; A- 2 Family Private Dwellings; A- 3
Dormitories; A- 4 Flats; and A- 5 Hotels.
Page
Group B Educational Buildings: All those buildings which are meant for education from a
nursery to the university, are included in this group, for example, schools, colleges, Universities,
Training Institutes, etc. These buildings provide facilities like class rooms, staff cabins, drawing
rooms, laboratories, admin blocks, seminar halls; recreation halls, library, playfields, gymnasium
etc.
Group C Institutional Buildings: This group includes any building which is used for the
purposes such as medical, health, physical or mental disease, care of infants or aged persons, etc.
These buildings normally meant for healthcare for the occupants.
These buildings are further subdivided into three groups viz, C1 Hospitals; C-2 Custodian
Institutions (a financial institution that has the legal responsibility for a customer's securities) and
C-3 panel Institutions (a group of persons selected for some services).
Group D Assembly Buildings: This group includes any building where groups of people
assemble or gather for amusement / entertainment. For eg: theatres, cinema halls, assembly halls,
auditoriums, exhibition halls, museums, restaurants, places of worship (temple, mosque, church,
etc.), club rooms, passenger stations, public transportation services; open air theatres, sports
pavilions( i.e., stadium), swimming pools, etc.
Group E Business Buildings : A commercial building is a building that is used for
commercial use. Types can include office buildings, warehouses, shopping malls, etc
Group F Mercantile Buildings: This group includes any building or part of a building which
is used as shops, stores, market for sale and display of products or wares either wholesale or
retail.
Group G Industrial Buildings: This group includes any building in which products of
different kinds and properties, are fabricated, assembled or processed. For example, laboratories,
assembling plants, laundries, gas plants, power plants, refineries, diaries
Group H Storage Buildings: This group includes to store materials such as cement, iron/steel;
home appliances etc. eg: godowns
Group I Hazardous Buildings: This group includes those building structures which are used
for the storage, handling, manufacture/ processing of materials which are liable to burn and prove
hazardous to building contents. Hazards may be due to fire, poisonous fumes or gases ,
explosions, ignition, etc., from materials subjected to various operations. Buildings used for
storage of explosive materials, manufacture of synthetic leather, explosives, fire works, etc., .
Page
is different for
Area
Scheme
City area
City are
FSI
1
4
3
Remarks
Only Ground floor is allowed.
Facing street
of > 12 mts width
Facing street
of < 12 mts width
Roads (mts.)
Road up to 9mts. and less.
More than 9 mts and upto 12
mts.
More than 12 mts and upto 18
mts.
More than 18 mts and upto 40
mts.
More than 40 mts.
Minimum Road
Remarks
Page
Width of Proposed
1
(4 ) THE AREA OF ROOMS:
Bed rooms, living rooms, drawing room, dining room (min) .9.4 sq mts
Kitchen and store rooms (min)
5.45 sq mts
Bathrooms and dressing rooms
1.85 4.5 sq mts
Water Closet ( WC ); Urinal rooms .
0.89 1.1 sq mts
( 5 ) HEIGHT OF ROOF: Roof height on each floor is 2.7 mts ( min ) and for bath room and WC
is 2.1 mts ( min)
(6) AREA OF DOORS, WINDOWS & VENTILATORS: This shall be 1/6 th to 1/10th of the
floor area of the room. In addition, every room should have ventilator .
(7) STAIR CASE: The stair case shall have area not more than 12 sq
mts. The pitch shall be in the range of 30o to 45o and flight shall have steps neither < 3 nor > 12.
Minimum width of stair shall be 900 mm.
(8) LIFT: This shall be provided for buildings having more than 3 floors excluding the ground
floor.
(9) SEPTIC TANK: shall be provided as per number of floors / rooms .
(10) HEIGHT OF COMPOUND WALL: The maximum height of compound
wall on road
side shall not be more than
1.5 mts
and
the gates shall
open inwards.
On other sides, the height of
compound
was shall
be 1.8
mts.
(11) OPEN SPACE: The open space width shall be
mts
( max) for front, rear and sides .
and 3
(12) PARKING SPACE: Parking spaces for cars required for cinemas, shopping areas and offices
located in central areas are to be allocated as per National Building Code.
BUILDING BYE-LAWS: Every locality has its own peculiarities in respect of weather
conditions, availability of material and labour and thus adopts its own method of construction. In
addition, every locality has certain rules and regulations which help in controlling the
development of locality. The rules and regulations covering the requirements and ensure the
safety of the public, minimum use of rooms , area limitations are known as Building bye-laws.
importance of
A sudden movement
of
the
EARTHQUAKE RESISTANT
BUILDINGS:
Earths surface often causing
a
damage is called as
Earthquake.
So,
Earthquake
causes vibrations /motions
in ground in
random fashion,
both
horizontally and
vertically and also in
all directions
radiating
from
the
epicenter.
The intensity and
duration of seismic vibrations
depends upon
magnitude of the earthquake ,
its depth
of focus, distance from
epicenter
etc It is therefore essential to ensure
(i) stability, (ii) strength (iii)
serviceability by means of design of the building.
Earthquake
causes shaking
of the ground so that
a building resting
on it
will experience motion at its
base and
leads
to collapse finally due to the
resulting inertia
forces.
From Newtons first law of motion even though the base of the building moves with the ground,
the roof has of tendency to stay in its original position. But since the walls and columns are
connected to it, they drag
along with
inertia forces
on
the roof
Structural
elements
such as
floor slabs, walls, columns and
foundations
and the
connections
between
them must be designed to safely
transfer
these inertia forces through them. Walls or columns are the critical elements in transferring the
inertia forces. But , in traditional construction, slabs and beams receive more care and attention
during design and construction than walls and columns. Failure of masonry walls have been
observed because of their thin and materials used for it , in the past due to
1
Page
the roof
element. .
earthquake effect.
Hence,
importance also is to be
columns.
Twist in buildings due
to earthquake induces more
frames
and walls.
It is best to
minimize this
buildings have symmetry in plan.
Indian Seismic
has provisions to come certain issues.
given
damage
twist by
Code (
for
walls and
of window
ensuring that
IS 1893: 2002)
An earthquake
(i)Good structural configuration: Its size, shape and structural system carrying loads are such that
they ensure a direct and smooth flow of inertia forces to the ground.
(ii) Adequate stiffness: Load resistant system is to be followed so that the earthquake induced
deformations in it do not damage under low to moderate shaking.
(iii) Lateral strength : The maximum lateral ( horizontal ) force
the damage induced by an earthquake.
(iv) Good ductility: Favourable design and detailing strategies
building from the earthquakes.
can resist
resist the
is best
Page
A
building
consists
of a invariably
number
of as
rooms
including material
toilets
/ bath
times
stones
have been
used
a construction
with
limerooms,
as
kitchen, Hall, bed rooms
etc interconnected through corridors, passages
the binder for construction of forts and
defense structures. Egyptians have
and each room may contain
a number of
doors, windows, almirahs, cup
used not
limeexceed
and gypsum
as cementing
materials
inbe used
the in
famous
Pyramids.
Wall thickness should
450
mm.
Round
stone
boulders
should
not
the construction.
boards whereas building
drawing reveals
the details
of all building
Since the earthquake
is such
a function
of
mass, the building
shallwindows,
be as light aslintels,
elements
as
foundations,
doors,
floors, of
The force
calcareous
rocks
used by
the
Romans possible.
were arches,
either roofs,
composed
sanitary
and
electrical
represent
The
limestones
burned
in fittings.
Kilns or Usually
mixturesthese
of fittings
limestones
and symbolically.
puzzolanic materials
As far as
possible,
the
parts
of
the
building
should
be
tied
together
in
graphical ash,
symbols
the shortest
forms
the concrete.
objects and
components.
Hence, is
(volcanic
tuff) are combining
into
a ofhard
The
natural cement
such a manner that
the
building
acts
as
one
unit.
obtainedisbythe
burning
and of
crushing
the and
stones
containing clay, carbonate of lime
drawing
language
Engineers
Architects.
(CaCO3) and a little
Projecting
parts shall be avoided as far as
possible.
If the projecting
brown in color and is also known as Roman cement.
BUILDING
A planreinforced
is the graphical
someand
scale
parts cannot be avoided
, theyPLANS:
shall be properly
and firmlyrepresentation
tied to the main to
structure
theiron
design shall be inthe
accordance
with
ISof
1893:
surface
the 2002.
earthwas
as projected
anda represented
on the
paperinon
which in
The
artificial
cement
invented by
mason Joseph
Aspdin
England
the
drawn.
to for this
represent
a plan, cement
the
1824.plan
He is took
out In order
a patent
cementthese
andelements
called it on
Portland
plan
is conventionally
prepare at inthe
window
level (The
member
at
because
it had resemblance
its color
aftersillsetting,
to ahorizontal
variety of
sandstone
Buildings havingthe
plans
with
shapes
like
L
Y
shall
preferably
be
separated
into
rectangular
parts
which
in Portland
England.
baseisoffound
a window
opening) in
rather
than
at the plinth level ( Within the context of
by providing separation
sections
at
appropriate
places.
construction, it is the top of the foundation walls).
The manufacture of Portland cement was started in England around 1825. Belgium
Structures shall not
founded onstarted
loose soils
will
an earthquake.
andbeGermany
thewhich
same
insubside
1855. during
America
started the same in 1872 and India
was installed in Tamil Nadu in 1904.
PROPERTIES OF CEMENT:
It gives strength to the masonry works.
It is an excellent binding material.
It is easily workable
It offers good resistance to the moisture
It possesses a good plasticity.
It hardens
early. sill level
Window
Plinth level
1BMCP NOTES
1
1