HAT300 V1.3 en PDF
HAT300 V1.3 en PDF
OPERATING MANUAL
Smartgen Electronics
http://www.smartgen.com.cn/
CONTENT
1.
DESCRIPTION ...............................................................................3
2.
FEATURES ...................................................................................3
3.
OPERATION
.................................................................................4
4.
6.
.......................................14
SPECIFICATION ...........................................................................16
8.
........................................17
........................................18
9.
.............................................................................18
10.
LINK TO PC
11.
Version1.3
Page 2 of 20
1. DESCRIPTION
The HAT300 is an Automatic Transfer System Control Module. It precisely
measure/display two source 3-phase AC voltage and output free voltage
controlling switch signal. This module is suitable for a variety of ATS system
and can be widely used to electric devices in many fields such as electric
power, communication, petroleum, coaling, metallurgy, rail, municipal business,
smart mansion etc.
2. FEATURES
Measure two source multi-parameters include over voltage, under voltage,
over frequency, under frequency, miss phase.
Compatible to multi-type of automatic transfer switches(ATS):
no OFF position(two segments kind), such as SOCOMEC VS switch;
one OFF position(three segments kind), such as SOCOMEC VE switch.
two OFF position, such as the ATS composed of two circuit breakers or two
contacts;
Compatible to automatic switching of two utility source, two generating
power or between one utility source and one generating power;
Microprocessor based design, LED display, tactile key operation;
Measure and display two source 3-phase AC voltage precisely;
ATS power switching circuits that supply for ATS;
Configurable priority of supply able to set I# supply priority or II# supply
priority or NONE supply priority;
Function of start generator;
Function of auto transfer when one switch closing failures and another
works well;
Auto/Manual button available, mandatory opening or closing switch in
manual mode;
Password to prevent the miss operation of non-professionals;
Function of re-closing to prevent instantaneous power off aiming at switch
which opening as voltage being low;
HAT300 Automatic Control Module ISSUE 2006-11-10
Version1.3
Page 3 of 20
3. OPERATION
3.1 OPERATION PANEL
LED display screen can display multi -parameters of two power sources such
as voltage, delay value, and setting value etc.
HAT300 Automatic Control Module ISSUE 2006-11-10
Version1.3
Page 4 of 20
push-button. The
push-button. The
function is used to
function is used to
push-button. The
manual mode.
push-button. The
manual mode.
push-button. The
Version1.3
Page 5 of 20
no power.
#1 closed lamp: The lamp will illuminate when #1 power is connected with
the load.
#2 closed lamp: The lamp will illuminate when #2 power is connected with
the load.
3.2 DISPLAY
Press the
The first screen (display of the line voltage Uab or the delay time of the
normality or the abnormality of the #1#2 power counted down)
or
Display priority: (#1 power normal delay>#2 power normal delay>#1 power
abnormal delay>#2 power abnormal delay>display of Uab line voltage) #1
power Uab line voltage will be displayed after all the display of delay is done.
The second screen (Ubc: #1 line voltage)
Version1.3
Page 6 of 20
The screen will display the alarm state if there is alarm of #1 or #2 power.
#1 closing failure
#2 closing failure
#1 opening failure
#2 opening failure
#1 power serious failure
#2 power serious failure
Both #1 and #2 power are closed at same time.
Note: if there is alarm of #1 power or # II power, pressing the
button, the
module will transfer to the manual mode, and the alarm state will be reset.
4. SETTING OPERATION
4.1 MANUAL/AUTO MODE SETTINGS
Press the
Version1.3
Page 7 of 20
mode.
l When the controlling module is set into Auto mode, the Auto lamp will
be turned on. The controlling module will estimate the quality of both
the power and close or open the switches automatically. If both the
powers work well, the switches will be turned on according to the
priority of them. If both the powers are normal at the same time, the
switch that first close will supply for load. It will not be switched to
another power until abnormality occurs in the power.
l
When the controlling module is set into the manual mode, the manual
lamp will be turned on. Press the
button, the
button or the
switch.
be displayed as follows:
000
Default password: 123. Press the
button
to circulate the number from 0 to 9. The parameters can not be set until the
password is confirmed. The parameters are displayed as follows:
The first screen: setting the normal delay time of the
(0-999s)
P
- 01
Press the
#1 power, range:
The second screen: setting the normal delay time of the #2 power, range:
(0-999s)
P
- 02
Press the
The third screen: setting the abnormal delay time of the #1 and #2 power,
range: (0-999s)
P
- 03
Press the
Version1.3
Page 8 of 20
The fourth screen: setting the delay time of the start generator, range:
(0-999s)
P
- 04
Press the
The fifth screen: setting the delay time of the stop generator, range:
(0-999s)
P
- 05
Press the
000: no priority
001: #1 power prior to transfer
002: #2 power prior to transfer
The eighth screen: setting ATS shut delay, range: (0-20s)
P
- 08
Press the
Version1.3
Page 9 of 20
Press the
Press the
Version1.3
Page 10 of 20
8.
9.
10.
11.
12.
13.
0-5.0S(0)
0-10.0S(0)
0-10.0S(0)
1# ATS Abnormal Input
2# ATS Abnormal Input
Gen Start Output(normal open)
Note:
The below table is the detail information for the above settings.
Item
Description
It is the delay of #1 power from voltage
Normal delay time of the #1 power
abnormal to voltage normal.
It is the delay of #2 power from voltage
Normal delay time of the #2 power
abnormal to voltage normal.
Abnormal delay time of the #1 and It is the delay of #1 or #2 power from
#2 power
voltage normal to voltage abnormal.
It is the delay form #1 power is
Delay time of the start generator
abnormal to start generator.
When #1 power is set to priority
transfer, if #1 and #2 is normal at the
same time, the switch will transfer load
to #1 power source.
When #2 power is set to priority
transfer, if #1 and #2 is normal at the
same time, the switch will transfer load
to #2 power source.
the transfer priority of #1 and #2
When setting for no priority, if #1, 2
power
power is normal at the same time and
#1,2 take no load, the switch will first
transfer load to #1 power source.
ONLY when #1 power is abnormal, the
#2 power will supply for load; if the
switch have been taken load, it will not
switched to another power until
abnormality occurs in the power.
Setting the Modbus Slave ID of the
Communication address
controller you wish to communicate
with.
It is the delay from #1 power breaker
opened to #2 power breaker start to
Transfer rest time
close or from #2 power breaker
opened to #1 power breaker start to
close.
Version1.3
Page 11 of 20
Item
Start generator delay time
Stop generator delay time
Over voltage
Under voltage
Description
It is the delay from #1 power is
abnormal to send out start generator
signal.
It is the delay from #1 power is normal
to send out stop generator signal.
The setting are used to configure the
#1 and #2 power over voltage point in
the event of the #1 or #2 voltage rising
above the setting value. This value can
be adjusted to suit user requirements.
The setting are used to configure the
#1 and #2 power under voltage point in
the event of the #1 or #2 voltage falling
below the setting value. This value can
be adjusted to suit user requirements.
Breaker close pulse. If it is set to zero,
it will held.
Breaker open pulse.
After the module has received a close
state input, the breaker close output
continue to held until the delay is
expended.
When the breaker fail to close for the
first time, the module will open
breaker, and then attempt to close for
the second time, if the second time
closing breaker is still failure, the
module will send out closing breaker
failure signal.
When the breaker fail to open for the
first time, the module will close
breaker, and then attempt to open for
the second time, if the second time
opening breaker is still failure, the
module will send out opening breaker
failure signal.
Description
It is the input of #1 breaker fault such
as the circuit breaker is short-circuit.
It is the input of #2 breaker fault such
as the circuit breaker is short-circuit.
Version1.3
Page 12 of 20
Transfer to Off-Position
Not used
1# ATS Abnormal Input
IN2
Same as above
2# ATS Abnormal Input
Transfer to Off-Position
NOTE: The above two Auxiliary digit inputs dont permitted the same selection
choices.
Configurable digit output(Relay K5) define
Item
Description
Not used
Reserve1
Factory used
It include closing failure, opening failure
Fault Output
and breaker fault of #1, 2 source.
It include #1 closing failure, opening
Transition Failure Output
failure and #2 closing failure, opening
failure.
1# Volt Normal Output
It is active when #1 voltage is normal.
1# Volt Abnormal Output
It is active when #1 voltage is abnormal.
2# Volt Normal Output
It is active when #2 voltage is normal.
2# Volt Abnormal Output
It is active when #2 voltage is abnormal.
Auto Position(mode) Output
It is active in auto mode.
Manual Position(mode) Output
It is active in manual mode.
1# Shut Up Output
#1 closing breaker output.
1# Shut Off Output
#1 opening breaker output.
2# Shut Up Output
#2 closing breaker output.
2# Shut Off Output
#2 opening breaker output.
When the start generator signal is
active, the output relay energized. When
Gens Start Output(normal open)
the start generator signal is inactive, the
output relay de-energized. Here the DC
supply is necessary.
When the start generator signal is
inactive, the output relay energized.
Gens Start Output(normal close)
When the start generator signal is
active, the output relay de-energized.
Version1.3
Page 13 of 20
Terminal
Diameter
of Wire
Vin(9-35VDC)
1.0mm
GND
1.0mm
A1
1.5mm
B1,C1,N1
1.0mm
A2
1.5mm
B2,C2,N2
1.0mm
Description
Engine-generator battery positive
input. It is not necessary. Fuse of Max.
1A Is Recommended.
Engine-generator battery negative
input. It is common earth terminal of all
switch inputs.
Connect to #1 power
L1 output.
(Fuse of 10A is Recommended)
Connect to #1 power
L2, L3, N
output. (Fuse of 1A is Recommended)
Connect to #2 power L1 output. (Fuse
of 10A is Recommended)
Connect to #2 power L2, L3, N output.
(Fuse of 1A is Recommended)
Version1.3
Page 14 of 20
Terminal
Diameter
of Wire
POS1
1.0mm
POS2
1.0mm
IN1
1.0mm
IN2
1.0mm
K1
K2
K3
K4
K5
1.5mm
1.5mm
1.5mm
1.5mm
1.0mm
LO
1.5mm
NO
1.5mm
Description
It is the input of #1 breaker closing
auxiliary contact. It is active to be
connect to GND.
It is the input of #2 breaker closing
auxiliary contact. It is active to be
connect to GND.
Configurable digit input1. It is active to
be connect to GND.
Configurable digit input2. It is active to
be connect to GND.
#1 breaker closed output.
#1 breaker opened output.
#2 breaker closed output.
#2 breaker opened output.
Configurable digit output.
It is used to supply for ATS. It come
from #1 and #2 power phase A. Any of
#1 and #2 phase A voltage is normal it
will output.
It is used to supply for ATS. It come
from #1 and #2 power phase N. Any of
#1 and #2 phase A voltage is normal it
will output.
Version1.3
Page 15 of 20
7. SPECIFICATION
Power supply:
DC: 9-35V come from engine-generator battery.
AC: come from phase A and N of two source, voltage>140V
Input voltage: 220V+30% 50Hz single-phase or 380V+30% 50/60Hz
3-phase 4 wires
Power consumption: Less than 2VA in normal voltage
Relay output: 10A 250VAC
LO, NO output: 10A 250VAC
Dimensions: 144x96x116mm
Panel cutout: 138x92mm
Weight: 0.83kg
Operation condition:
Temperature: -30 - +70Celsiur degree
Humidity: 20 - 95% no concreting
Version1.3
Page 16 of 20
Version1.3
Page 17 of 20
Default
Please download the HAT300 configuration software from the below web site.
http://www.smartgen.com.cn/
10.LINK TO PC
This below figure show the link from PC to HAT300 module.
HAT300 Automatic Control Module ISSUE 2006-11-10
Version1.3
Page 18 of 20
Defined
1# ATS Abnormal Input
2# ATS Abnormal Input
Defined
Gen Start Output(normal open)
Range
Default
0-999s
10s
0-999s
10s
0-999s
5s
0-999s
60s
0-999s
90s
0-999s
0-20.0s
5s
5.0s
Version1.3
Page 19 of 20
Item
ATS break delay
Delay for transfer over
Again shut delay
Again break delay
Over voltage
Under voltage
Range
1-20.0
0-5.0s
0-10.0s
0-10.0s
50-360V
50-360V
Others
Item
Transfer priority
ATS type
Module address
Content
#1 transfer is prior
Three segment(one OFF position)
1
Default
5.0s
0.0s
0.0s
0.0s
264V
160V
Version1.3
Page 20 of 20