Professional Documents
Culture Documents
Chemistry Notes For Class 12 Chapter 15 Polymers
Chemistry Notes For Class 12 Chapter 15 Polymers
Polymerisation
The process by which the monomers get combined and transformed into polymers. is known as
polymerisation.
n [Monomer] Polymer
Difference between Polymers and Macromolecules
Polymers are also called macromolecules due to their large size but converse is not always true.
A macromolecule mayor may not contain monomer units, e.g., chlorophyll (C55H72O5N4Mg) is
a macromolecule but not a polymer since there are no monomer units present so we can
conclude that all polymers are macromolecules while all macromolecules may not be polymers
in nature.
Classification of Polymers Based on Source of Origin
(i) Natural polymers Those polymers which occur in nature. i.e., in plants or animals. are called
natural polymers.
(ii) Synthetic polymers The polymers which are prepared in the laboratory are known as
synthetic polymers or man-made polymers, e.g., polythene, synthetic rubber, PVC, nylon-66,
teflon, orlon etc.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
2|Page
(i) Linear polymers These are the polymers in which the monomer units are linked to one
another to form long linear chains. These linear chains are closely packed in space. The close
packing results in high densities, tensile strength and high melting and boiling points. e.g., high
density polyethene, nylon and polyesters are linear polymers.
(ii) Branched chain polymers In such polymers, the monomer units are linked to form long
chains with some branched chains of different lengths with source. As a result of branching,
these polymers are not closely packed in space. Thus, they have low densities, low tensile
strength as well as low melting and boiling points. Some common examples of such polymers
are low density polyethene, starch, glycogen etc.
(iii) Cross-linked polymers or network polymers In such polymers, the monomer units are
linked together to form three dimensional network. These are expected to be quite hard, rigid
and brittle. Examples of cross linked polymers are bakelite, glyptal, melamine-formaldehyde
polymer etc.
Classification of Polymers Based on Mode of Polymerisation
(i) Addition polymers The polymers formed by the polymerisation of monomers containing
double or triple bonds (unsaturated compounds) are called addition polymers. Addition
polymers have the same empirical formula as their monomers.
Addition polymers can further be classified on the basis of the types
of monomers into the following two classes:
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
3|Page
Homopolymers The polymers which are obtained by the polymerisation of a single type of
monomer are called homopolymers.
Copolymers The polymers which are obtained by the polymerisation of two or more
monomers are called copolymers
(ii) Condensation polymers The polymers which are formed by the combination of monomers
with the elimination of small molecules such as water, alcohol, hydrogen chloride etc., are
known as condensation polymers, e.g., nylon 6,6 is formed by the condensation of
hexamethylene diamine with adipic acid.
4|Page
3. Thermoplastics These are linear polymers and have weak van der Waals forces acting
in the various chains. These forces are intermediate of the forces present in the
elastomers and in the fibres. When heated, they melt and form a fluid which sets into a
hard mass on cooling. Thus, they can be cast into different shapes by using suitable
moulds, e.g., polyethene and polystyrene.
(Plasticizers are high boiling esters or haloalkanes. These are added to I plastics to make
them soft rubber like. J
4. Thermosetting plastics These are normally semifluid substances with low molecular
masses. When heated, they become hard and infusible due to the cross-linking between
the polymer chains. As a result, they also become three dimensional in nature. A few
common thermosetting polymers are bakelite, melamine-formaldehyde resin and urea
formaldehyde resin.
Types of Polymerisation
1. Chain Growth Polymerisation or Addition Polymerisation
It involves formation of reactive intermediate such as free radical, a carbocation or a carbanion.
For this polymerisation monomers used are unsaturated compounds like alkenes; alkadienes
and their derivatives. Depending upon the nature of the reactive species involved. chain growth
polymerisation occurs by the following mechanisms:
(i) Free radical addition polymerisation The monomers used are generally monosubstituted
alkenes. The most commonly used catalysts are benzoyl peroxide, hydrogen peroxide or t-butyl
peroxide etc.
Mechanism The reaction involves the following steps
Step I Chain initiation step In this step, peroxide undergoes homolytic fission, e.g., benzoyl
peroxide on heating produces phenyl initiator free radical.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
5|Page
Step II Chain propagation step The new free radical adds to another molecules of monomer
to form a larger free radical.
Step III Chain termination step There are three ways of chain termination: Coupling
reaction, disproportionation reaction, chain transfer reaction. One mode of termination of chain
is shown as under:
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
6|Page
7|Page
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
8|Page
It is tough, flexible, transparent, chemically inert as well as poor conductor pf electricity. It has
moderate tensile strength but good tearing strength.
It is used in the insulation of electricity carrying wires and manufacture of queeze bottles, toyes
and flexible pipes.
(ii) High density polyethylene (HOP)
It has high density due to close packing. It is also chemically inert and more tougher and
harder.
It is used for making containers, house wares, bottles, toyes, electric insulation etc.
2. Polystyrene (Styrone)
The monomers are styrene molecules. It is thermoplastic. It is used for making toys, radio and
TV cabinets
3. Polyvinylchloride (PVC)
It is used for making rain coats, toys, electrical insulation. It is hard and resistant to heat and
chemicals.
4. Polypropylene (PP)
It is obtained by polymerising propylene in the presence of Ziegler-Natta catalyst.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
9|Page
It is chemically inert and resistant to attack by corrosive reagent. It is used in making oil seals,
gaskets and also for non-stick surface coated utensils.
6. Polyacrylonitrile
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
10 | P a g e
The polyamides are identified by numbers. These numbers refer to the number of carbon atoms
in diamine and in the dibasic acid. As in the above case, the carbon atoms are 6 in each case,
therefore the product is described as _nylon-66.
Properties and uses
Nylon-66 is a linear polymer and has very high tensile strength. It shows good resistance to
abrasion. Nylon-66 is usually fabricated into sheets. It is used in bristles for brushes and in
textile
2. Nylon-6
Nylon-6 is obtained by heating caprolactam with water at a high temperature.
Resins
1. Phenol-Formaldehyde Polymer
(Bakelite and Related Polymers)
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
11 | P a g e
These polymers are obtained by the condensation reaction of phenol with formaldehyde in the
presence of either acid or a base catalyst. The reaction involves the formation of methylene
bridge at ortho, para or both ortho and para positions. A linear or cross linked material is
obtained depending upon the condition of reaction.
Uses
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
12 | P a g e
Bakelite is used for making combs, photograph records, electrical switches etc. Soft bakelites
with low degree of polymerisation are used as binding glue for laminated wooden plants, in
varnishes and lacquers.
2. Melamine-formaldehyde Resin
It is a copolymer formed by the polymerisation of melamine (which is a heterocyclic triamine)
and formaldehyde as follows :
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
13 | P a g e
4. Natural Rubber
Natural.rubber is a coiled linear 1, 4-polymer of isoprene.
In the polymer chain of natural rubber, the residual double bonds are located between C2 and
C3 of the isoprene unit. All these double bonds have cis configuration, and thus natural rubber
is cis-l,4-polyisoprene.
In the natural rubber, there is no polar substituent. The only intermolecular forces are van der
Waals type. The cis-configuration gives the polymeric chain of natural rubber a coiled
structure. As a result, it can be stretched by the application of a force. When the force is
removed, the chain returns back to its original coiled shape.
Natural rubber is soft and sticky. It can be used only in the temperature range 10C-50C. At
higher temperature, it becomes soft and at low temperature, it becomes brittle. It has higb water
absorption capacity. It is attacked by oxidising agents and organic solvents. As such, it cannot
be used very extensively for commercial puposes.
Vulcanisation of Rubber
The properties of natural rubber can be modified by introducing -S-S- polysulphide crosslinks
in its structure. This process of introducing -S-S- crosslnks in the structure of natural rubber by
heating with sulphur at 11OC is called vulcanlsation of rubber.
Vulcanisatlon is carried out by adding sulphur (3-5%) and zinc oxide to the rubber, and then
heating the object at about 110Cfor about 20-30 minutes. Zinc oxide accelerates the rate of
vulcanisation. Vulcanisation introduces polysulphide (-S-S-) bonds between the adjacent
chains. These crosslinks tend to limit the motion of chains relative to each other.
5. Neoprene
Polymer formed by polymerisation of chloroprene is neoprene or synthetic rubber.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
14 | P a g e
The polymer is known by several commercial names such as lucite, acrylite, plexiglass and
perspex.
Properties and uses
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
15 | P a g e
It is a hard and transparent polymer and is quite resistant to the effect of light, heat and ageing.
It is used, in the manufacture of unbreakable lights, protective coatings, dentures, and in
making windows for aircrafts.
2. Glyptal
It is a polyester having crosslinks. It is a thermosetting plastic. It is obtained by condensation of
ethylene glycol and phthalic acid or glycerol and phthalic acid.
When its solution in a suitable solvent is evaporated, it leaves a tough but non-flexible film. It
is, therefore, used in the manufacture of paints and lacquers.
3. Terylene (Dacron)
It is a condensation product of ethylene glycol and terephthalic acid.
Polymerisation is carried out at 420 to 460 K in the presence of catalyst mixture of zinc acetate
and antimony trioxide.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
16 | P a g e
2. Nylon-2-Nylon-6
It is an alternating polyamide copolymer of glycine (H2N-CH2-COOH) and amino caproic acid
[H2N(CH2) 5COOH] and is biodegradable.
Some More Impotant Polymers
1. Saran is a copolymer of vinyl chloride and Isused for wrapping food materials.
2. ASS rubber is a copolymer of acrylonitrile, buta-1, 3-diene and styrene.
3. Bubble gum contains styrene butadiene rubber.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)
17 | P a g e
4. Epoxy resins are used In making adhesives such as araldite, etc. These are the copolymer
of epichlorohydrin and bisphenol-A.
5. Thikol is another variety of synthetic rubber which is a copolymer of ethylene chloride
and sodium tetrasulphide (Na2S4).
6. Dynells a copolymer of vinyl chloride and acrylonitrile and is used for making human
hair wigs.
7. Silk Is a thread like natural polymer which is obtained from cocoons of sllk worms. It is
a natural polyamide fibre.
8. Thermocol Is a foamed plastic obtained by blowing air through molter polystyrene or
polyurethane.
9. Superglue is a polymer of methyl -cyanoacrylate and is obtained by anionic
polymerisation of monomer.
www.ncerthelp.com (Visit for all ncert solutions in text and videos, CBSE syllabus, note and many more)