Professional Documents
Culture Documents
m3l13 PDF
m3l13 PDF
3
Quantization and
Coding
Principles of DPCM;
DPCM modulation and de-modulation;
Calculation of SQNR;
One tap predictor;
The standard sampling rate for pulse code modulation (PCM) of telephone grade
speech signal is fs = 8 Kilo samples per sec with a sampling interval of 125 sec.
Samples of this band limited speech signal are usually correlated as amplitude of speech
signal does not change much within 125 sec. A typical auto correlation function R ( )
for speech samples at the rate 8 Kilo samples per sec is shown in Fig 3.13.1. R ( = 125
sec) is usually between 0.79 and 0.87. This aspect of speech signal is exploited in
differential pulse code modulation (DPCM) technique. A schematic diagram for the basic
DPCM modulator is shown in Fig 3.13.2. Note that a predictor block, a summing unit
and a subtraction unit have been strategically added to the chain of blocks of PCM coder
instead of feeding the sampler output x (kTs) directly to a linear quantizer. An error
sample ep (kTs) is fed.
0 Ts 3 Ts
+
+
x (nTs )
u(nTs)
Predictor
There is another possibility of decreasing the coded bit rate compared to a PCM
system if an SQNR as achievable by a PCM codec with linear equalizer is sufficient. If
( ) (
the predictor output x kT s can be ensured sufficiently close to x kT s then we can)
simply encode the quantizer output sample v(kTs) in less than 8 bits. For example, if we
choose to encode each of v(kTs) by 6 bits, we achieve a serial bit rate of 48 kbps, which is
considerably less than 64 Kbps. This is an important feature of DPCM, especially when
the coded speech signal will be transmitted through wireless propagation channels.
We will now develop a simple analytical structure for a DPCM encoding scheme
to bring out the role that nay be played by the prediction unit.
As noted earlier,
= x ( kT s ) + q ( kT s ) 3.13.3
Demodulator output
b(nTs ) v(nTs ) + u (nTs ) x (t ) o/p
Decoder Low pass
i/p filter Analog
+ Output
Fig. 3.13.3 Schematic diagram of a DPCM demodulator; note that the demodulator is
very similar to a portion of the modulator
As in PCM coding, we are assuming instantaneous sampling and ideal low pass filtering.
The first term in the above expression is the predictor gain (Gp). This gain visibly
increases for better prediction, i.e., smaller variance of ep(kTs). The second term, SNRp is
a property of the quantizer. Usually, a linear or uniform quantizer is used for simplicity
in a DPCM codec. Good and efficient design of the predictor plays a crucial role in
enhancing quality of signal or effectively reducing the necessary bit rate for transmission.
In the following we shall briefly take up the example of a single-tap predictor.
Single-Tap Prediction
A single-tap predictor predicts the next input example x(kTs) from the immediate
previous input sample x([k-1]Ts).
Let, x (kTs ) = x (k k 1) = the k-th predicted sample, given the (k-1)th input sample
= a.u (k 1 k 1)
Here, a is known as the prediction co-efficient and u (k 1 k 1) is the (k-1)-th input to
the predictor given the (k-1)-th input speech sample, i.e., x(k-1).
Now the k-th prediction error sample at the input of the quantizer may be expressed as
e p (kTs ) e p (k )
= x(k ) x (k k 1)
= x(k ) a.u (k 1 k 1) 3.13.4
The mean square error or variance of this prediction error samples is the statistical
expectation of e2p(k).
Now,
E[e2 p (k )] = E[{x(k ) a.u (k 1 k 1)}2 ]
The above expression shows that the mean square error or variance of the prediction error
can be minimized if a = R(1)/R(0).
Problems
Q3.13.1) Is there any justification for DPCM, if the samples of a signal are known to be
uncorrelated with each other?
Q3.13.2) Determine the value of prediction co-efficient for one tap prediction unit if
R(0) = 1.0 and R(1) = 0.9.