Aeb 1F
Aeb 1F
Aeb 1F
ALL-OPTIFLOW
Design IE
in Block Design
Application The stuffing box or mechanical seal housings of the various shaft
For handling liquid to highly viscous, neutral or aggressive, sealing types are interchangeable within one size. The various
uncontaminated or abrasive liquids, liquids containing gases or mechanical seal housing parts form a modular construction system
which tend to froth, also containing fibers and solid matter and, in case of conversion to a different mechanical seal design, can
be easily combined with one another.
In waste water and waste water treatment engineering, chemical
and petrochemical industry, paper and cellulose industry, soap Installation spaces for mechanical seals according to DIN EN 12 756
and fats industry, paint and lacquer industry, food and beverage (except for double mechanical seal).
industry, plastics industry, ceramics industry, agriculture, sugar
industry and in shipbuilding. For further information refer to pages 4, 5, 6 and 7.
Operating
Self-priming, single-stage, rotary positive displacement pump.
Technical data
Conveying elements are the rotating eccentric screw (rotor) and
Deliveries, admissible speed ranges and required drive powers
the fixed stator. In the cross-sectional plane, both are in contact
are to be taken from the performance graph on page 3 and/or
with one another at two points forming two sealing lines along
the separate individual characteristic curves.
the length of the conveying elements. The contents of the sealed
chambers which are formed as the rotor turns, are displaced AEB1F
axially and with complete continuity from the suction to the Delivery Q l/min up to 3800
discharge end of the pump. Despite rotor rotation, there is no Temperature of fluid pumped t C up to 100
turbulence. The constant chamber volume excludes squeezing, Delivery pressure
thus ensuring an extremely gentle low-pulsating delivery. single-stage p bar up to 6
Pump outlet pressure pd bar up to 16
Design features
The pump and drive are held together by the bearing bracket to Attainable underpressure ps bar up to 0,95
form a modular unit. Viscosity mPas up to 300.000
Admissible solids content vol % up to 60
By means of external casing connecting screws (clamping
screws), the discharge casing, stator and suction casing are
interconnected. The suction casings are designed particularly The stated performance information serves only as an outline of
favorable to flow. The pump sizes 403 to 5503 are supplied in performance of our products. For exact limits of application please
cast iron and are provided with staggered holes for cleaning. refer to the quotation and acceptance of order.
The stator vulcanized into a tube is provided with external collars
vulcanized to it on both sides, reliably sealing towards the Max. admissible grain sizes and fiber lengths
suction casing and discharge casing and protecting the stator
Size 103 203 403 553 703
shell from corrosion.
max. grain size mm 3 3,8 5 6,8 6,8
The exchangeable shaft sealing housing or mechanical seal
max. fiber length mm 42 48 60 79 79
housing (subsequent conversion to another sealing variant is
possible) are arranged between the suction casing and bearing 1003
Size 1603 3003 5503
bracket.
max. grain size mm 9,5 9,5 14 20
The torque of the drive is transmitted over the driving shaft and the 98
max. fiber length mm 98 130 210
joint shaft onto the rotor. On both sides, the joint shaft ends in
liquid-tight encapsulated bolt joints, which are of particularly Increasing solids content and increasing grain size require a reduction of
simple and sturdy design and easily absorb the eccentric move- the pump speed:
ment of the rotor.
depending upon the fluid to be pumped and the elastomers employed
Shaft seal depending on the pump size/design, speed and fluid to be pumped
By uncooled, cooled or heated stuffing box or by uncooled or cooled depending on the direction of rotation, inlet pressure
maintenance-free unbalanced, single or double-acting mechanical 5 bar at sizes 3003, 5503
seal.
Drive
The drive can be provided by non-explosion-proof or explosion-
proof three-phase motors, gear motors or control gear. For drive
options see page 10. For technical data and dimensions, please
refer to the separate sales documentation, data sheet
19-00-0000-111-3.
Installation
AEB pumps may be installed horizontally or vertically, depending
on the shaft seal. In case of vertical arrangement, shaft shank
downwards is not admissible.
Exchangeability of components
The components of all eccentric screw pumps are of a modular
design. This allows a simple and cost-effective spare parts
management even if different series and designs of pumps are
used.
Sizes of the series AEB1F Data on the performance range not covered by AEB1F series are to be taken from the last page of this
brochure and/or the individual brochures of the other series.
For exact performance data, please refer to the individual characteristics.
The numbers indicate the theoretic delivery in l/min with n = 400 1/min and p = 0 bar
Design
IE = Industrial design with external bearing
Bearing design
0 = external bearing in drive unit
Suction and 1 = DIN-flanges
according to dimensional sheet, pages 8 and 9
discharge 3 = ANSI-flanges
branch design X = Suction and/or discharge branch of special design
Branch 1, 2, 3, 4 For arrangement please refer to the representation, page 8.
design P01 = Stuffing box of normal design (without sealing chamber ring / without flushing ring)
P02 = Stuffing box with flushing ring
P03 = Stuffing box with internal sealing chamber ring
P04 = Stuffing box with external sealing chamber ring
P0X = Non-mechanical shaft seal of special design
design For pump sizes 103 203 403 553 703 1003 1603 3003 5503
(continued) Shaft diameter at location of shaft seal 25 30 35 43 43 53 53 60 75
X=design G0K = individual mechanical seal,
possible X X X X X X X X X
DIN EN 12 756, design K, shape U
G0N = as above, however design N X X X X X X X X X
G0S = individual mechanical seal,
DIN EN 12 756, design K, shape U,
X X X X X X X X X
rotating part with integrated locking
device and pump-sided throttling ring
G0T = as above, however design N X X X X X - - X X
G0Q = individual mechanical seal,
DIN EN 12 756, design K, shape U with X X X X X X X X X
quench
G0D = double mechanical seal
G0X = mechanical seal of special design
design available on request
Double shell D = Double shell for heating/cooling, available in stainless steel only.
Connections as threaded nipples for liquid media. Maximum heating/cooling pressure 6 bar,
maximum heating temperature + 100C, maximum cooling temperature -40C
Double shell 1 = Suction case with double shell
(all qualities)
N Rotor with temperature play
M as a function of the temperature
H of the fluid pumped
T
Y = Rotor ductile hard chromium-plated W = Winding protection on joint shaft
Z = Rotor metallically coated X = Other designs
S = Worm on joint shaft
Suction and 1 = gray cast iron EN-GJL-250
Part 304
secured
1 center
punch mark
P02 Stuffing box with P03 Stuffing box with P04 Stuffing box with
flushing ring internal sealing external sealing
chamber ring. chamber ring.
To be employed for very abrasive To be employed for pure fluids with To be employed in case of
fluids pumped with external internal sealing or for abrasive incompatibility of the external
flushing. fluids with external sealing. sealing liquid with the fluid pumped
p = -0,7 to 12 bar p = -0,8 to 6,0 bar or if air inlet is to be avoided.
p = -0,9 to 12 bar
122 Bearing bracket 215 Mechanical seal cover 304 Joint sleeve
123 Tensioning set 218 O-ring 305 Joint lubricant
125 Driving shaft 219 Mechanical seal 306 Joint clamp
201 Stud bolt 220 Locking pin 307 Joint shaft
202 Self-locking nut 232 Shaft seal ring 308 Joint collar
203 Gland half 234 Throttling ring 401 Rotor
204 Shaft sealing housing 235 O-ring 402 Stator
207 Stuffing box 236 Locking pin 403 Stator gasket delivery-side
208 Flushing ring 245 Hexagon screw 404 Stator gasket suction-side
209 Sealing chamber ring 251 Sealing compound 501 Gasket for suction casing
212 Screw plug 301 Joint bolt 502 Screw plug
213 Joint tape 302 Joint bush 503 Joint tape
214 Mechanical seal housing 303 Bush for joint bolt 504 Delivery casing
Arrangement
4 holes_____
z = number of
holes __________
Arrangement
8 holes_____
Dimensions in mm, nominal width of ANSI- Sense of rotation: Normally counter-clockwiseas seen from the
llanges (DN) in inches. driving side with DN1 = discharge branch,
Subject to alteration. DN2 = suction branch, change of rotation
possible, then DN1 = suction branch,
DN2 = discharge branch
DN1/DN2 k1 d1 z DN1/DN2 k1 d1 z
50 125 18 4 2 120,6 19 4
65 145 18 4 2 139,7 19 4
80 160 18 8 3 152,4 19 4
100 180 18 8 4 190,5 19 8
125 210 18 8 5 215,9 22,2 8
150 240 22 8 6 241,3 22,2 8
200 295 22 12 8 298,4 22,2 8
with internal
P03 with
P03 internal sealing
sealing chamber
chamber ring
ring G0S/G0Twith
G0S/G0T withflushing
flushingconnection
connection
P04with
P04 withexternal
externalsealing
sealingchamber
chamberring
ring G0D with
G0D with sealing
sealing connection
connection
G0D with sealing connection
Standard supply
Drive options
AEB-IE with electric motor AEB-IE with gear motor AEB-IE with infinitely
variable gear
ALLWEILER GmbH
Postfach 200123 46223 Bottrop
Kirchhellener Ring 7779 46244 Bottrop
Germany
Tel. +49 (0)2045 966-60
Fax +49 (0)2045 966-679
E-mail: [email protected]
Internet: http://www.allweiler.com
GB/2017.03 Ident-No. 228493