GA-F2A68HM-H: User's Manual
GA-F2A68HM-H: User's Manual
GA-F2A68HM-H: User's Manual
User's Manual
Rev. 1001
Motherboard
GA-F2A68HM-H
Motherboard
GA-F2A68HM-H
Copyright
2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by
any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the
revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,
drivers, or when looking for technical information.
Example:
Table of Contents
Chapter 3 Appendix.......................................................................................................30
3-1 Configuring SATA Hard Drive(s)...................................................................... 30
3-2 Drivers Installation........................................................................................... 33
Regulatory Statements............................................................................................... 34
Contact Us................................................................................................................. 35
-3-
GA-F2A68HM-H Motherboard Layout
KB_MS_USB
ATX_12V
VGA
FM2+
ATX
HDMI
R_USB30
CPU_FAN
USB_LAN CI
DDR3_2
DDR3_1
SYS_FAN1
3 2
AUDIO Realtek BAT
GbE LAN
GA-F2A68HM-H
PCIEX16 SATA3
M_BIOS
PCIEX1
iTE
Super I/O AMD A68H
PCI
CODEC
SYS_FAN2
SPDIF_O CLR_CMOS SATA3 0 1
Box Contents
55 GA-F2A68HM-H motherboard
55 Motherboard driver disk 55 Two SATA cables
55 User's Manual 55 I/O Shield
The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
-4-
GA-F2A68HM-H Motherboard Block Diagram
x16 x1 D-Sub
BIOS
4 SATA 6Gb/s
1 PCI Express x1
8 USB 2.0/1.1
CODEC
1 PCI
MIC (Center/Subwoofer
Speaker Out)
Line Out (Front Speaker Out)
Line In (Rear Speaker Out)
S/PDIF Out
-5-
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
Prior to installation, make sure the chassis is suitable for the motherboard.
Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
When handling the motherboard, avoid touching any metal leads or connectors.
It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
Before unplugging the power supply cable from the motherboard, make sure the power supply
has been turned off.
Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
Do not place the computer system on an uneven surface.
Do not place the computer system in a high-temperature environment.
Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
-6-
1-2 Product Specifications
APU FM2+ Socket:
- AMD A series processors
- AMD Athlon series processors
(Go to GIGABYTE's website for the latest CPU support list.)
Chipset AMD A68H
Memory 2 x DDR3 DIMM sockets supporting up to 64 GB of system memory
* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical
memory is installed, the actual memory size displayed will be less than the size of
the physical memory installed.
* The maximum 64 GB of system memory can be supported using 16 GB (or above)
memory modules. GIGABYTE will update the memory support list on the official
website when the memory modules are available on the market.
Dual channel memory architecture
Support for DDR3 2133/1866/1600/1333 MHz memory modules
Support for AMD Memory Profile (AMP)/Extreme Memory Profile (XMP) memory
modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)
Onboard Integrated Graphics Processor:
Graphics - 1 x D-Sub port, supporting a maximum resolution of 1920x1200
- 1 x HDMI port, supporting a maximum resolution of 4096x2160
* The resolution of 4096x2160 can be supported when using an FM2+ APU; the
maximum resolution supported is 1920x1200 when using an FM2 APU.
* Support for HDMI 1.4a version.
- Maximum shared memory of 2 GB
Audio Realtek ALC887 codec
High Definition Audio
2/4/5.1/7.1-channel
* To configure 7.1-channel audio, you have to use an HD front panel audio module
and enable the multi-channel audio feature through the audio driver.
Support for S/PDIF Out
LAN Realtek GbE LAN chip (10/100/1000 Mbit)
Expansion Slots 1 x PCI Express x16 slot, running at x16
(The PCI Express x16 slot conforms to PCI Express 3.0 standard.)
* To support PCI Express 3.0, you must install an FM2+ APU.
1 x PCI Express x1 slot
(The PCI Express x1 slot conforms to PCI Express 2.0 standard.)
1 x PCI slot
Multi-Graphics Support for AMD Dual Graphics technology
Technology * Only A series APUs support AMD Dual Graphics.
Support for AMD Eyefinity technology
Storage Interface Chipset:
- 4 x SATA 6Gb/s connectors
- Support for RAID 0, RAID 1, RAID 10, and JBOD
USB Chipset:
- 2 x USB 3.0/2.0 ports on the back panel
- 8 x USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through
the internal USB header)
-7-
Internal 1 x 24-pin ATX main power connector
Connectors 1 x 4-pin ATX 12V power connector
4 x SATA 6Gb/s connectors
1 x APU fan header
2 x system fan headers
1 x front panel header
1 x front panel audio header
1 x S/PDIF Out header
2 x USB 2.0/1.1 headers
1 x speaker header
1 x Clear CMOS jumper
1 x chassis intrusion header
Back Panel 1 x PS/2 keyboard/mouse port
Connectors 1 x D-Sub port
1 x HDMI port
2 x USB 3.0/2.0 ports
4 x USB 2.0/1.1 ports
1 x RJ-45 port
3 x audio jacks (Line In, Line Out, Mic In)
I/O Controller iTE I/O Controller Chip
Hardware System voltage detection
Monitor APU/System temperature detection
APU/System fan speed detection
APU overheating warning
APU/System fan fail warning
APU/System fan speed control
* Whether the fan speed control function is supported will depend on the cooler you
install.
BIOS 1 x 64 Mbit flash
Use of licensed AMI UEFI BIOS
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
Unique Features Support for @BIOS
Support for Q-Flash
Support for Xpress Install
Support for EasyTune
* Available functions in EasyTune may differ by motherboard model.
Support for Smart Recovery2
Support for ON/OFF Charge
Bundled
Norton Internet Security (OEM version)
Software
Operating Support for Windows 8.1/7 32-bit/64-bit
System Support for Windows XP 32-bit
* To support Windows XP 32-bit, you must install an AMD FM2+ Kaveri APU.
-9-
1-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.
(Note) Make sure the drivers for the Chipset, onboard graphics, and external graphics card are properly
installed.
- 10 -
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
D-Sub connection to this port.
HDMI Port
The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM
audio output. You can use this port to connect your HDMI-supported monitor.
The maximum supported resolution is 4096x2160 (Note), but the actual resolutions supported are
dependent on the monitor being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI.
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the
multi-channel audio feature through the audio driver.
When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent
an electrical short inside the cable connector.
(Note) The resolution of 4096x2160 can be supported when using an FM2+ APU; the maximum resolution
supported is 1920x1200 when using an FM2 APU.
- 11 -
1-8 Internal Connectors
1 4
2
3
13
5
6
11
9 12 7 8 10 4 5
1) ATX_12V 8) F_PANEL
2) ATX 9) F_AUDIO
3) CPU_FAN 10) SPEAKER
4) SYS_FAN1/2 11) SPDIF_O
5) SATA3 0/1/2/3 12) F_USB1/F_USB2
6) BAT 13) CI
7) CLR_CMOS
ATX:
12 24 Pin No. Definition Pin No. Definition
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 -5V
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
1 13 ATX)
12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX)
ATX ATX)
Be sure to connect fan cables to the fan headers to prevent your APU and system from overheating. Overheating
may result in damage to the APU or the system may hang.
These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
- 13 -
DEBUG
PORT
A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be
used, the total number of hard drives must be an even number.
A RAID 10 configuration requires four hard drives.
To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA Configuration,"
for more information.
6) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal
object like a screwdriver to touch the positive and negative terminals of the battery holder,
making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
Always turn off your computer and unplug the power cord before replacing the battery.
Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.
Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain
about the battery model.
When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery
(the positive side should face up).
Used batteries must be handled in accordance with local environmental regulations.
Open: Normal
Always turn off your computer before clearing the CMOS values.
After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually
configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).
- 14 -
8) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
Power LED Power Switch
PLED (Power LED):
System Status LED Connects to the power status indicator on the
PLED-
S0 On chassis front panel. The LED is on when the
PW- system is operating. The LED is off when the
PLED+
S3/S4/S5 Off
PW+
the way to turn off your system using the power switch (refer to Chapter
HD-
RES+
- 15 -
10) SPEAKER (Speaker Header)
Connects to the speaker on the chassis front panel. The system reports system startup status by issuing
a beep code. One single short beep will be heard if no problem is detected at system startup.
Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.
Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power
outlet to prevent damage to the USB bracket.
- 16 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.
Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS,
it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing
may result in system malfunction.
It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other
unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to
clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in
this chapter or introductions of the battery/clear CMOS jumper in Chapter 1 for how to clear the CMOS values.)
Function Keys
On the main menu of the BIOS Setup program, press arrow keys to move among the items and press <Enter>
to accept or enter a sub-menu. Or you can use your mouse to select the item you want.
When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.
The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.
- 17 -
2-2 M.I.T.
This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,
total memory size, CPU temperature, Vcore, and memory voltage.
Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall
system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory
and reduce the useful life of these components. This page is for advanced users only and we recommend you not to
alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings
may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)
`` M.I.T. Current Status
This screen provides information on CPU/memory frequencies/parameters.
- 18 -
`` Advanced CPU Core Settings
&& CPU Clock Ratio, CPU Frequency
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&& Core Performance Boost (Note 1)
Allows you to determine whether to enable the Core Performance Boost (CPB) technology, a CPU
performance-boost technology. (Default: Auto)
&& Turbo Performance Boost Ratio (Note 1)
Allows you to determine whether to improve CPU performance. (Default: Disabled)
&& Core Performance Boost Ratio (Note 1)
Allows you alter the ratio for the CPB. The adjustable range is dependent on the CPU being installed.
(Default: Auto)
&& AMD Cool&Quiet function
Enabled Lets the AMD Cool'n'Quiet driver dynamically adjust the CPU clock and VID to reduce
heat output from your computer and its power consumption. (Default)
Disabled Disables this function.
&& cTDP function
Allows you to set the TDP consumption. Options are Disabled, 45W, 60W. (Default: Disabled)
&& SVM Mode
Virtualization enhanced by Virtualization Technology will allow a platform to run multiple operating systems
and applications in independent partitions. With virtualization, one computer system can function as multiple
virtual systems. (Default: Enabled)
&& C6 Mode
Allows you to determine whether to let the CPU enter C6 mode in system halt state. When enabled, the
CPU core frequency will be reduced during system halt state to decrease power consumption. The C6
state is a more enhanced power-saving state than C1. (Default: Enabled)
&& CPU core Control
Allows you to determine whether to manually enable/disable CPU cores. Automatic mode allows the BIOS
to enable all CPU cores (number of cores available depends on the CPU being used). (Default: Automatic
mode)
&& APM
Enables or disables Application Power Management. (Default: Enabled)
(Note 1) This item is present only when you install a CPU that supports this feature.
(Note 2) This item is present only when you install a CPU and a memory module that support this feature.
- 19 -
&& Memory Frequency (MHz)
This value is automatically adjusted according to the CPU Clock Control and System Memory Multiplier
settings.
`` PC Health Status
&& Reset Case Open Status
Disabled Keeps or clears the record of previous chassis intrusion status. (Default)
Enabled Clears the record of previous chassis intrusion status and the Case Open field will
show "No" at next boot.
&& Case Open
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI
header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To
clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to
the CMOS, and then restart your system.
&& CPU Vcore/DRAM Voltage/+3.3V/+5V/+12V
Displays the current system voltages.
&& CPU/System Temperature
Displays current CPU/system temperature.
- 20 -
&& CPU/System Fan Speed
Displays current CPU/system fan speeds.
&& CPU Warning Temperature
Sets the warning threshold for CPU temperature. When temperature exceeds the threshold, BIOS will emit
warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF.
&& CPU/System Fan Fail Warning
Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or
fan connection when this occurs. (Default: Disabled)
&& CPU Fan Speed Control
Allows you to determine whether to enable the fan speed control function and adjust the fan speed.
Normal Allows the fan to run at different speeds according to the CPU temperature. You can
adjust the fan speed with EasyTune based on your system requirements. (Default)
Silent Allows the fan to run at slow speeds.
Manual Allows you to control the fan speed under the Fan Speed Percentage item.
Speed
Full Allows the fan to run at full speeds.
&& Fan Speed Percentage
Allows you to control the fan speed. This item is configurable only when CPU Fan Speed Control is set
to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.
&& 1st System Fan Speed Control (SYS_FAN1 Connector)
Allows you to determine whether to enable the fan speed control function and adjust the fan speed.
Normal Allows the fan to run at different speeds according to the system temperature. You can
adjust the fan speed with EasyTune based on your system requirements. (Default)
Silent Allows the fan to run at slow speeds.
Manual Allows you to control the fan speed under the Fan Speed Percentage item.
Speed
Full Allows the fan to run at full speeds.
&& Fan Speed Percentage
Allows you to control the fan speed. This item is configurable only when 1st System Fan Speed Control
is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.
&& 2nd System Fan Speed Control (SYS_FAN2 Connector)
Allows you to determine whether to enable the fan speed control function and adjust the fan speed.
Normal Allows the fan to run at different speeds according to the system temperature. You can
adjust the fan speed with EasyTune based on your system requirements. (Default)
Silent Allows the fan to run at slow speeds.
Manual Allows you to control the fan speed under the Fan Speed Percentage item.
Speed
Full Allows the fan to run at full speeds.
&& Fan Speed Percentage
Allows you to control the fan speed. This item is configurable only when 2nd System Fan Speed Control
is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.
`` Miscellaneous Settings
&& PCIe Slot Configuration
Allows you to set the operation mode of the PCI Express slots to Gen 1, Gen 2, or Gen 3. Actual operation
mode is subject to the hardware specification of each slot. Auto lets the BIOS automatically configure this
setting. (Default: Auto)
&& 3DMark01 Boost
Allows you to determine whether to enhance some legacy benchmark performance. (Default: Disabled)
- 21 -
2-3 System Information
This section provides information on your motherboard model and BIOS version. You can also select the default
language used by the BIOS and manually set the system time.
- 22 -
2-4 BIOS Features
- 23 -
&& Fast Boot
Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup
speed. (Default: Disabled)
&& VGA Support
Allows you to select which type of operating system to boot.
Auto Enables legacy option ROM only.
Driver
EFI Enables EFI option ROM. (Default)
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
&& USB Support
Disabled All USB devices are disabled before the OS boot process completes.
Initial All USB devices are functional in the operating system and during the POST.
Full
(Default)
Partial Initial Part of the USB devices are disabled before the OS boot process completes.
This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot
is set to Ultra Fast.
&& PS2 Devices Support
Disabled All PS/2 devices are disabled before the OS boot process completes.
Enabled All PS/2 devices are functional in the operating system and during the POST.
(Default)
This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot
is set to Ultra Fast.
&& NetWork Stack Driver Support
Disabled Disables booting from the network. (Default)
Enabled Enables booting from the network.
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
To cancel the password, press <Enter> on the password item and when requested for the password, enter
the correct one first. When prompted for a new password, press <Enter> without entering any password.
Press <Enter> again when prompted to confirm.
NOTE: Before setting the User Password, be sure to set the Administrator Password first.
- 25 -
2-5 Peripherals
&& IOMMU
Enables or disables AMD IOMMU support. (Default: Disabled)
&& OnChip USB Controller
Enables or disables the integrated USB controller. (Default: Enabled)
&& HD Audio Azalia Device
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
&& Legacy USB Support
Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)
&& XHCI Hand-off
Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off
support. (Default: Enabled)
&& EHCI Hand-off
Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off
support. (Default: Disabled)
&& Port 60/64 Emulation
Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support
for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices.
(Default: Disabled)
&& USB Storage Devices
Displays a list of connected USB mass storage devices. This item appears only when a USB storage device
is installed.
&& Onboard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
- 26 -
`` GFX Configuration
&& Primary Video Device
Specifies the first initiation of the monitor display from the installed PCI graphics card, PCI Express graphics
card or the onboard graphics.
IGD Video Sets the onboard graphics as the first display.
PCIe Slot Video Sets the PCI Express graphics card on the PCI Express slot controlled by the
NB
North Bridge as the first display. (Default)
Slot
PCI Sets the graphics card on the PCI Slot as the first display.
&& Integrated Graphics
Enables or disables the onboard graphics function.
Auto The BIOS will automatically enable or disable the onboard graphics depending on
the graphics card being installed. (Default)
Disabled Disables the onboard graphics.
Force Always activates the onboard graphics, whether or not a PCI Express card is
installed.
&& UMA Frame Buffer Size
This item is configurable only when Integrated Graphics is set to Force. Frame buffer size is the total
amount of system memory allocated solely for the onboard graphics controller. MS-DOS, for example, will
use only this memory for display.
Options are: Auto (default), 256M, 512M, 1G, 2G.
`` SATA Configuration
&& OnChip SATA Channel
Enables or disables the integrated SATA controllers. (Default: Enabled)
&& OnChip SATA Type
Enables or disables RAID for the SATA controllers integrated in the Chipset or configures the SATA controllers
to AHCI mode.
Native IDE Configures the SATA controller to IDE mode. (Default)
RAID Enables RAID for the SATA controller.
AHCI Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specification that allows the storage driver to enable
advanced Serial ATA features such as Native Command Queuing and hot plug.
&& PORT0 Hot Plug~PORT3 Hot Plug
Enables or disable the hot plug capability for each SATA port. (Default: Disabled)
&& SATA Power on PORT0~SATA Power on PORT3
Enables or disables each SATA port. (Default: Enabled)
- 27 -
2-6 Power Management
- 28 -
&& Power On Password
Set the password when Power On By Keyboard is set to Password.
Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept.
To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter>
again without entering the password to clear the password settings.
&& Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
Disabled Disables this function. (Default)
Move Move the mouse to turn on the system.
Double Click Double click on left button on the mouse to turn on the system.
&& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,
PME event wake up, power on by mouse, power on by keyboard, and wake on LAN.
- 29 -
&& Boot Override
Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yes
to confirm. Your system will restart automatically and boot from that device.
&& Save Profiles
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and
save as Setup Profile 1~ Setup Profile 8. Press <Enter> to complete. Or you can select Select File in
HDD/USB/FDD to save the profile to your storage device.
&& Load Profiles
If your system becomes unstable and you have loaded the BIOS default settings, you can use this function
to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS
settings. First select the profile you wish to load and then press <Enter> to complete. You can select Select
File in HDD/USB/FDD to input the profile previously created from your storage device or load the profile
automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked
properly (last known good record).
Chapter 3 Appendix
3-1 Configuring SATA Hard Drive(s)
Before you begin, please prepare the following items:
At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives
with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive.
Windows setup disk.
Motherboard driver disk.
A USB flash drive.
A USB floppy disk drive (needed during Windows XP installation).
An empty formatted floppy disk (needed during Windows XP installation)
Steps:
1. Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Ensure
OnChip SATA Channel is enabled under Peripherals\SATA Configuration. Set OnChip SATA Type to RAID.
2. If you want to configure UEFI RAID, follow the steps in "C-1." To enter the legacy RAID ROM, save the
settings and exit BIOS Setup. Refer to "C-2" for more information.
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
- 30 -
C-1. UEFI RAID Configuration
This mode supports Windows 8.1 64-bit installation only.
To configure UEFI RAID, you need to prepare a USB flash drive using FAT 32 file format and copy all files
(including the UEFI RAID utility rcadm.efi) in the \BootDrv\UEFI RAID Utility folder in your motherboard driver
disk to the flash drive. Then follow the steps below.
Steps:
In BIOS Setup, go to BIOS Features and set Windows 8 Features to Windows 8 and CSM Support to Never.
Save the changes and exit BIOS Setup.
Running the UEFI RAID Utility
Restart your computer and press <F12> to enter the boot device configuration menu. Use the up or down arrow
key to select your USB flash drive which is prefixed with "UEFI:" string. Then press <Enter> to access the screen
as shown in Figure 3. To run the UEFI RAID utility, enter the following commands.
You can enter the commands at Shell or fsx: level (x represents the disk number for your USB flash drive).
Checking Disk Information
To see the hard drive information, enter the following commands and press <Enter>. You will see CONTROLLER
LIST and DISK LIST displayed on the screen.
rcadm -M -qa
Creating a RAID Array
To create a RAID array, refer to the following examples to enter the commands and press <Enter>. When
succeeded, the message which says "created successfully" will appear.
Example 1: Create a RAID 0 array with Drive 0 and Drive 1 and the array size is 40 GB.
rcadm -C -r0 -d 0 1 -s 40000
("C"=Create a array, "r0"=RAID 0, d 0 1=Drive 0 and Drive 1, "s 40000"=Size of 40 GB; to use the maximum
size allowed, do not enter "s x0000")
Example 2: Create a RAID 5 array with Drive 1~4 and the array size is 75 GB.
rcadm -C -r5 -d 1 2 3 4 -s 75000
("C"=Create a array, "r5"=RAID 5, d 1 2 3 4=Drive 1~4, "s 75000"=Size of 75 GB)
After you create the array, you can enter the "rcadm -M -qa" commands to see the array information. In addition
to the CONTROLLER LIST and DISK LIST information, you will see ARRAY LIST information displayed on
the screen, too.
Deleting an Array
To delete an array, enter the following commands and press <Enter>.
rcadm -D -a 1
("D"=Delete a array, "a 1"=Array 1, to delete all arrays, enter "a *")
When prompted to confirm, enter YES to delete or NO to cancel, and then press <Enter>.
To exit the UEFI RAID utility, enter "exit" and press <Enter>.
- 31 -
2. The selection bar will move to the Disks section on the right of the screen. Select the hard drives to be included
in the RAID array. Use the up or down arrow key to select a hard drive and press <Insert>. The selected
hard drive will be shown in green. To use all of the hard drives, simply press <A> to select all. Then press
<Enter> and the selection bar will move to the User Input section on the left bottom of the screen. (Figure 10)
3. First, select a RAID mode and press <Enter>. The selections available depend on the number of the hard drives
being installed. Then follow the on-screen instructions to specify the array size. You can select All available
space to use the maximum size allowed or use the up or down arrow key to adjust the size and press <Enter>.
4. Select a caching mode. Options include Read/Write, Read Only, and None. Then press <Enter> to proceed.
5. Finally, a message which says "Confirm Creation of Array" will appear. Press <C> to confirm or <Esc> to
return to the previous screen. To exit the RAID BIOS utility, press <Esc> and then press <C> to confirm.
Deleting an Array
The Delete Array(s) menu option allows for deletion of disk array assignments.
1. Select Delete Array(s) in the Main Menu and press <Enter>.
2. In the Arrays section, press the <Insert> key on the array you want to delete and then press <Enter> to proceed.
3. When prompted to confirm, press <C> to continue the deletion or <Esc> to cancel.
Deleting an existing disk array could result in loss of data. Record all array information including the
array type, the disk members, and stripe block size in case you wish to undo a deletion.
- 32 -
2: From your optical drive folder, double click the Menu.exe file in the BootDrv folder. A Command Prompt
window will open.
3: 3: Insert the blank formatted disk (if you're using a USB floppy disk drive, make sure it is designated as drive
A). Select the controller driver by pressing the corresponding letter from the menu and press <Enter>. For
the AMD A68H, select 6) hseries AHCI/RAID<A85>for XP.
Your system will then automatically copy the driver files to the floppy disk. Press any key to exit when finished.
Refer to the following for installing the driver during the Windows setup process.
Step 1:
Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message
"Press F6 if you need to install a 3rd party SCSI or RAID driver." A screen will then appear asking you to specify
an additional SCSI adapter. Press <S>.
Step 2:
Insert the floppy disk containing the SATA RAID/AHCI driver and press <Enter>. Then a controller menu similar
will appear. Select AMD AHCI Compatible RAID Controller-x86 platform and press <Enter>.
Step 3:
On the next screen, press <Enter> to continue the driver installation. After the driver installation, you can proceed
with the Windows XP installation.
- 33 -
Regulatory Statements
Regulatory Notices
This document must not be copied without our written permission, and the contents there of must not be imparted
to a third party nor be used for any unauthorized purpose.
Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects
at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text.
Also note that the information in this document is subject to change without notice and should not be construed
as a commitment by GIGABYTE.
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the
energy-saving features of this product (where applicable), recycling the inner and outer packaging (including
shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic
equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our
quality of life by ensuring that potentially hazardous substances are not released into the environment and are
disposed of properly.
- 34 -
Contact Us
You may go to the GIGABYTE website, select your language in the language list on the top right corner of the website.
GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to:
http://esupport.gigabyte.com
- 35 -