SADP User Manual (V2.0)

User Manual of SADP Software
Search Active Device Protocol

V2.0
User Manual of SADP Software 1
Table of Contents
Chapter 1 Overview .................................................................................................................... 1
1.1 Description ............................................................................................................................... 1

1.2 System Requirements .............................................................................................................. 1
Chapter 2 Running the SADP Software ....................................................................................... 2
2.1 Running SADP with Administrator Account ............................................................................. 2

2.2 Running SADP with other Admin Accounts .............................................................................. 2
2.3 Running SADP with Non-admin Accounts ................................................................................ 3
Chapter 3 Operating the SADP Software..................................................................................... 6
3.1 Searching Active Devices Online .............................................................................................. 6

3.2 Modifying Network Parameters ............................................................................................... 7
3.3 Restoring Default Password ..................................................................................................... 7
Chapter 1 Overview
1.1 Description
Search Active Devices Protocol software is a kind of user-friendly and installation-free
online device search tool. It searches the active online devices within your subnet
and displays the information of the devices. You can also modify the basic network
information of the devices using this software.
Note: Online intelligent devices search is not supported by SADP v2.0.
1.2 System Requirements

Operating System: Microsoft Windows XP/ Server2000/ Server 2003 32bits,
Windows 7 / Server 2008 32/64 bits;
CPU: Intel Pentium4 3.0 @3.00GHz or higher;
RAM: 1GB or higher;
Display: RADEON X700 series;
Minimum Resolution: 1024*768.
Chapter 2 Running the SADP Software

2.1 Running SADP with Administrator Account
Log in the computer as the administrator, and double-click to enter

the SADP software main interface as shown in Figure 2-1.
Figure 2-1 SADP Interface
2.2 Running SADP with other Admin Accounts

You can also run the SADP software with other accounts of the admin group.
For Windows 2000/XP/2003
Refer to Section 2.1 Running SADP with Administrator Account.
For Windows Vista/Win7/2008

Steps:
1. Right-click and click Run as administrator.

Figure 2-2 Run as Administrator
2. Click on the pop-up User Account Control dialog box to allow the
program and enter the main interface of SADP software.
Figure 2-3 User Account Control Dialog Box
2.3 Running SADP with Non-admin Accounts

If you log in the operating system with the non-admin accounts (e.g. users or guests),
you need to run the software as administrator or as other accounts of the admin
group.
For Windows 2000/XP/2003

Steps:
1. Right-click and click Run as.

2. Input the username and password of the administrator or other accounts of the
admin group and click to enter the main interface of SADP software.
Figure 2-5 Input Username and Password
For Windows Vista/Win7/2008
1. Right-click and click Run as administrator.

2. Input the password of administrator and click to enter SADP.
Figure 2-7 Input Administrator Password

Chapter 3 Operating the SADP

Software
3.1 Searching Active Devices Online
Search online devices automatically
After launch the SADP software, it automatically searches the online devices every 15
minutes from the subnet where your computer locates. It displays the total number
and information of the searched devices in the Online Devices interface. Device
information including the device type, IP address, port number, gateway, etc. will be
displayed.
Figure 3-1 Searching Online Devices
Note: Device can be searched and displayed in the list in 15 seconds after it went
online; it will be removed from the list in 45 seconds after it went offline.
Search online devices manually
You can also click to refresh the online device list manually. The newly
searched devices will be added to the list.
Note: You can click or on each column heading to order the information;
you can click to expand the device table and hide the network parameter panel
on the right side, or click to show the network parameter panel.
3.2 Modifying Network Parameters

Steps:
1. Select the device to be modified in the device list and the network parameters of
the device will be displayed in the Modify Network Parameters panel on the
right side.
2. Edit the modifiable network parameters, e.g., IP address and port number.
3. Enter the password of the admin account of the device in the Password field and
click to save the changes.
Figure 3-2 Modify Network Parameters
3.3 Restoring Default Password

Steps:
1. Contact our technical engineers to get the serial code.

Note: Serial code is a series of characters combined by the start time and the serial
number of the device.
2. Input the code in the Serial code field and click to restore the
default password.

SADP User Manual (V2.0)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SADP User Manual (V2.0)

Uploaded by

Copyright:

Available Formats

User Manual of SADP Software

Search Active Device Protocol

1.1 Description ............................................................................................................................... 1

Chapter 2 Running the SADP Software ....................................................................................... 2

2.1 Running SADP with Administrator Account ............................................................................. 2

Chapter 3 Operating the SADP Software..................................................................................... 6

3.1 Searching Active Devices Online .............................................................................................. 6

1.2 System Requirements

Chapter 2 Running the SADP Software

Log in the computer as the administrator, and double-click to enter

Figure 2-1 SADP Interface

2.2 Running SADP with other Admin Accounts

For Windows Vista/Win7/2008

1. Right-click and click Run as administrator.

Figure 2-2 Run as Administrator

Figure 2-3 User Account Control Dialog Box

2.3 Running SADP with Non-admin Accounts

For Windows 2000/XP/2003

1. Right-click and click Run as.

Figure 2-4 Run as Administrator

Figure 2-5 Input Username and Password

For Windows Vista/Win7/2008

1. Right-click and click Run as administrator.

Figure 2-6 Run as Administrator

2. Input the password of administrator and click to enter SADP.

Figure 2-7 Input Administrator Password

Chapter 3 Operating the SADP

Figure 3-1 Searching Online Devices

on the right side, or click to show the network parameter panel.

3.2 Modifying Network Parameters

click to save the changes.

Figure 3-2 Modify Network Parameters

3.3 Restoring Default Password

1. Contact our technical engineers to get the serial code.

You might also like