Professional Documents
Culture Documents
SDS Mounted Points and Wheels
SDS Mounted Points and Wheels
Product Name: Grinding and Cutting Wheels, Cup Wheels, Plugs & Cones, Mounted Point Wheels, Bench
Grinding Wheels
Forney SKUs: 60025, 60026, 60027, 60028, 60029, 60030, 60031, 60032, 60033, 60034, 60035, 60036,
60050, 60051, 60052, 60053, 60054, 60055, 72397, 72398, 72400, 72401, 72402, 72403,
72404, 72405, 72406, 72407, 72408, 72412, 72413, 72414, 72415, 72416, 72417, 72461,
72462, 72463, 72464, 72465, 72466, 72467, 72468, 72469, 72470, 72471, 72472
Manufacturer Name: Forney Industries, Inc.
Address: 2057 Vermont Drive, Fort Collins, CO 80525
Website: www. forneyind.com
Email: [email protected]
Phone Number: 714-554-6770
Fax Number: 714-554-6772
SDS Creation Date: April 1st. 2014 Revised 12/15/2016 Rev. 2.1
Inhalation, Acute: Dust Inhalation may cause coughing, shortness of breath or irritation.
Inhalation, Chronic: Dust Inhalation may affect breathing capacity.
Ingestion: No known adverse effects, but ingestion not recommended.
Skin: Not absorbed through skin. Dust may cause irritation/rash to some.
Eye: Dust may irritate eyes.
Other Potential Risks: Grinding may create elevated sound levels, which may affect
hearing and may aggravate pre-existing respiratory condition.
INGREDIENTS &
CHEMICAL IDENTITY CAS # %
(COMMON NAME):
1 * Aluminum Oxide (Alumina) 1344-28-1 0% - 95%
2 * Silicon Carbide (Crystolon) 409-21-2 0% - 90%
3 * Phenol Formaldehyde
Non-established 1% - 30%
(Phenolic Resin)
4 * Sodium Fluoaluminate
15096-52-3 0% - 20%
(Cryolite)
5 * Fiborous Glass (Fiberglass) N/A 0% - 20%
6 * Zirconium Oxide 1314-23-4 0%-80%
7 * Iron Pyrite 12068-85-8 0%-20%
8 * Sulfur 7704-34-9 0%-15%
9 * Calcium Oxide 1305-78-8 0% - 10%
10 * Iron Oxide 1309-37-1 0%-5%
11 * Graphite 7782-42-5 0%-5%
12 * Potassium Flouroborate 14075-53-7 0%-5%
Eye Contact: Immediately flush eyes with water for at least 15 to 20 minutes.
Make sure the dust is completely washed off.
Get medical attention, if irritation symptoms develop or persist.
Skin Contact: Wash skin with soap and rinse plenty of water. Get medical attention if
irritation symptoms develop or persist.
Inhalation: Remove affected person to fresh air. Apply artificial respiration if necessary.
Seek medical assistant if affected person is still having trouble breathing.
Ingestion: If accidentally ingested, contact physician for medical attention.
Waste disposal method: Dispose-of in a secured sanitary landfill consistent with applicable
Federal, State and Local Laws and Regulations
Handling: Handle with adequate ventilation (See OSHA 29CFR 1910.94 Ventilation)
and 29CFR 1910.1000 (Air Contaminates)
Storage: Store in dry area, away from heat source.
Ideal storage temperature 65-70F (18-24C), 50-60% RM
General Hygiene Practices: Wear proper gloves, eye and face protection.
3 * Phenol Formaldehyde
Non-establised Non-establised
(Phenolic Resin)
4 * Sodium Fluoaluminate
2.5 mg/m3 2.5 mg/m3
(Cryolite)
5 * Fiborous Glass 15mg/m3 total dust, 10mg/cu.m total
(Fiberglass) 5mg/m3 respirable dust, 5mg/m3
fraction respirable fraction
Hazardous Polymerization: Hazardous polymerization does not occur under normal condition and usage.
Stability: Stable under normal condition.
Condition to avoid: Unspecified.
Hazarous decompositon: Dust from grinding could contain ingredients listed in seciton 3 and other,
potentially more hazardous components of the base material being ground
or coatings applied to the base material.
Acute Toxicity: This product has not been tested for its toxicity.
Ingestion: If accidentally ingested, contact physician for medical attention.
Inhalation: Dust inhalation may cause coughing, shortness of breath or irritation.
Skin: Not absorbed through skin. Dust may cause irritation/rash to some.
Eye: Dust may irritate eyes.
Other Potential Risks: Grinding may create elevated sound levels, which may affect.
hearing and may aggravate pre-existing respiratory condition.
Carcinogenicity: Silica, Amorphous, Fused - IARC-3, NIOSE-X LD50/LC50
Values are not appropriate or available.
Waste Disposal Method: Dispose-of in a secured sanitary landfill consistent with applicable
Federal, State and Local Laws and Regulations.
HCS Classification: This product is Exempted from the regulatory requirement HCS
California Proposition 65: WARNING: Dust generated from cut, sand, drill
or grind materials such as wood, paint, cement, masonry or metal when using
this product offen contains chemicals known to cause cancer, birth defects,
or other reproductive harm.
Canadian CEPA: None toxic substances. All of the ingredients are listed on
the Canadian DSL.
Label Requirement: Not controlled under O.S.H.A and under W.H.M.S. when used according to
Industry safety standard.
Hazard Ratings
Hazadous Material 4- Extreme
Information System (USA) 3- Serious
2- Moderate
1- Slight
0- Minimal
Notice to reader
The information and recommendations set forth herein are taken from sources believed to be
accurate. However, Griton Industries, Inc. makes No Warranty with respect to accuracy of the
information or the suitability of the recommendations, and assumes No Liability to any user thereof.