Professional Documents
Culture Documents
Microondas Daewoo Kog-261m 262m 281m 282m
Microondas Daewoo Kog-261m 262m 281m 282m
Microwave Oven
KOG-261M, KOG-262M
KOG-281M, KOG-282M
TABLE OF CONTENTS
PROPER USE AND SERVICE PRECAUTIONS ................................................................................. 2
SPECIFICATIONS ................................................................................................................................ 3
FEATURES DIAGRAM ......................................................................................................................... 4
EARTHING INSTRUCTIONS ............................................................................................................... 5
INSTALLATION..................................................................................................................................... 5
OPERATION PROCEDURE................................................................................................................. 6
CONTROLS .......................................................................................................................................... 7
INTERLOCK MECHINISM FUNCTIONS AND ADJUSTMENTS ........................................................ 18
SAFETY PRECAUTIONS FOR DISASSEMBLY AND REPAIR.......................................................... 20
DISASSEMBLY AND ASSEMBLY ....................................................................................................... 21
TROUBLE SHOOTING GUIDE ............................................................................................................ 27
MEASUREMENT OF THE MICROWAVE OUTPUT POWER ............................................................ 34
MICROWAVE RADIATION TEST ........................................................................................................ 34
WIRING DIAGRAM ............................................................................................................................... 36
CIRCUIT DESCRIPTION...................................................................................................................... 37
COMPONENT TEST PROCEDURE.................................................................................................... 40
SAFETY INTERLOCK CONTINUITY TEST......................................................................................... 41
PRINTED CIRCUIT BOARD................................................................................................................. 42
CIRCUIT CHECK PROCEDURE...................................................................................................... 42
COMPONENT INFORMATION ........................................................................................................ 47
PRINTED CIRCUITS BOARD .......................................................................................................... 48
P.C.B. CIRCUIT DIAGRAM .............................................................................................................. 49
P.C.B. LOCATION NO ...................................................................................................................... 50
EXPLODED AND PARTS LIST ............................................................................................................ 51
1
CAUTION : This Device is to be Serviced Only by Properly Qualified Service Personnel. Consult
the Service Manual for Proper Service Procedures to Assure Continued Safety
Operation and for Precautions to be Taken to Avoid Possible Exposure to Excessive
Microwave Energy.
CAUTIOU
MICROWAVE RADIATION
2
SPECIFICATIONS
KOG-261M / 262M KOG-281M / 282M
POWER SUPPLY 120V~60Hz, SINGLE PHASE WITH EARTHING
MICROWAVE 920W 1200W
POWER CONSUMPTION
GRILL 1050W 1050W
MICROWAVE ENERGY OUTPUT 600W 800W
MICROWAVE FREQUENCY 2450MHz
OUTSIDE DIMENSIONS (W x D x H) 465 x 360 x 274 mm 495 x 382 x 289 mm
CAVITY DIMENSIONS (W x D x H) 290 x 290 x 200 mm 320 x 330 x 225 mm
NET WEIGHT 14kg 15kg
TIMER 59 min. 99 sec.
FUNCTION SELECTIONS MICROWAVE / GRILL
MICROWAVE POWER LEVELS 10 LEVELS
( ) : For KOG-281M/282M
3
FEATURES DIAGRAM
4
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of
electric shock by providing an escape, wire for the electric current. This appliance is equipped with a
cord having a earthing wire with a earthing plug. The ploug must be plugged into an outlet that is
properly installed and earthed.
WARNING : Improper use of the earthing plug can result in a risk of electric shock. consult a
qualified electrician or serviceman if the earthing instructions are not completely
understood, or if doubt extension to whether the appliance is properly earthed. If it
necessary to use an extension cord, use only a 3-wire extension cord that has a 3-
blade earthing plug, and a 3-slot receptacle that will accept the plug on the appli-
ance. The marked rating of the extension cord should be equal to or greater than
the electrical rating of the appliance.
INSTALLATION
Steady, flat location
1 This oven should be set on a steady, flat surface.
This oven is designed for counter top use only.
Leave space behind and side
2 All air vents should be kept a clearance. lf all vents are covered during operation, the oven may
overheat and, eventually, oven failure.
Away from Radio and TV sets
3 Poor television reception and radio interference may result if the oven is located close to a TV,
Radio, or antenna, feeder and so on.
Position the oven as far from them as possible.
Away from heating appliances and water taps
4 Keep the oven away from hot air, steam or splash when choosing a place to position it, or the
insulation might be adversely affected and breakdowns occur.
Power supply
5 Check uour local power source. This oven requires a current of approximately 10 amperes.
120V 60Hz.
Power supply cord is about 1.1 meters long.
The voltage used must be the same as specified on this oven. Using a higher voltage may
result in a fire or other accident causing oven damage. Using low voltage will cause slow cook-
ing. We are not responsible for damage resulting from use of this oven with a voltage of
ampere fuse other than those specified.
This appliance is supplied with cable of special thpe, which, if damaged, must be repaired with
cable of same type. such a cable can be purchased from DAEWOO and must be installed by a
Qualified Person.
6 Examine the oven after unpacking for any damage such as:
QA misaligned door, broken door, A dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
5
OPERATION PROCEDURE
This section includes useful information about oven operation.
8 Ifdoes
the START pad is touched and the oven
4 The oven automatically cook on full power
unless set to a lower power level.
not operate, check the area between
the door and door is closed securely. The
oven will not start cooking until the door is
5 The display will show : 0 when the oven
is plugged in.
completely closed or the program has
been reset.
6
CONTROLS
1. Touch CLOCK/
A.START pad.
The display will stop blinking and the colon starts blinking.
CLOCK/ If you selected 12 hour clock system this digital clock allows you to set
A.START from 1:00 to 12:59.
If you selected 24 hour clock system, this digital clock allows you to
4. Touch CLOCK/ set from 0:00 to 23:59
A.START pad.
NOTE : If you attempt to enter an incorrect time, the time will not be set and a error signal tone will
sound. Touch the CLOCK/A.START pad re-enter the time.
7
WEIGHT DEFROSTING
WEIGHT DEFROST lets you easily defrost food by eliminating guesswork in determining defrosting
time. The minimum weight for WEIGHT DEFROST is 200 grams. The maximum weight for WEIGHT
DEFROST is 3000 grams. Follow the steps below for easy defrosting.
DO THIS THIS HAPPENS...
The WEIGHT DEFROST indica-
AUTO tor lights and 0 is displayed.
DEFROST And the g indicator starts blink-
ing.
1. Touch AUTO
DEFROST pad.
NOTE : To prevent over defrosting thin areas or edges can be shielded with strips of aluminum foil.
8
TIME DEFROSTING
When TIME DEFROST is selected, the automatic cycle divides the defrosting time into periods of
alternating defrost and stand times by cycling on and off.
DO THIS THIS HAPPENS...
The WEIGHT DEFROST indica-
AUTO tor lights and 0 is displayed.
DEFROST And the g indicator starts blink-
ing.
1. Touch AUTO
DEFROST pad.
2. Touch AUTO
DEFROST pad once
more.
When you touch START pad, the TIME DEFROST indicator starts
START
blinking to show the oven is in the TIME DEFROST mode. The dis-
play counts down the time to show you how much defrosting time is
4. Touch START pad. left in the TIME DEFROST mode. The oven beeps during the defrost-
ing cycle to signal that the food needs to be turned or rearranged.
When the defrosting time ends, you will hear 3 beeps.
NOTE : To prevent over defrosting, thin areas or edges can be shielded with strips of aluminum foil.
9
COOKING IN ONE STAGE
START When you touch START pad, the M/W indicator starts blinking to
show the oven is cooking.
The display counts down the time to show how much cooking time is
4. Touch START pad. left. When the cooking time ends, you will hear 3 beeps.
NOTE: Using lower power levels increase the cooking time which is recommended for foods such as
cheese, milk and slow cooking of meats.
10
GRILL COOKING
This function allows you to brown food quickly.
The heating element is located in the top of the oven.
There is no pre-heating the oven for grill cooking. Place food inside the oven when setting the con-
trols.
DO THIS... THIS HAPPENS...
START When you touch START pad, the GRILL indicator starts blinking to
show the oven is cooking.
The display count down the time to show how much cooking time is
3. Touch START pad. left. When the cooking time ends, you will hear 3 beeps.
11
AUTO START
Allows you to program cooking to start at a time you select.
The food will automatically start cooking at the desired time.
2. Touch CLOCK/
A.START pad.
START When you touch START pad, the present time appears in the display
and the cooking program indicators come on.
The AUTO START indicator and the colon start blinking.
4. Touch START pad. When the selected start time arrives the oven bigins. Operating and
the oven light turns on. The AUTO START indicator goes off and the
next stage indicator begins to blink.
When the cooking is completed you will hear 3 beeps. The oven turns
off and the present time appears in the display.
NOTE: AUTO START can be used for time cooking, if clock is set. If the oven door is opened
after programming AUTO START, it is necessary to touch the START pad for the time of
day to appear in the readout so that the oven will automatically begin programmed cook-
ing at the chosen AUTO START time. Before setting, check to make sure the clock is
showing the correct time of day.
12
TO CHECK AUTO START TIME
Once you have correctly programmed the oven for AUTO START, the present time will appear on the
display.
SPEEDY COOK
SPEEDY COOK allows you to reheat for 30 seconds at 100% (full power) by simply touching the
SPEEDY COOK pad.
By repeatedly touching the SPEEDY COOK pad, you can also extend reheating time to 5 minutes by
30 seconds.
13
ONE TOUCH COOKING
One touch cook allows you to cook or reheat many of your favorite foods by touching just one pad. To
increase quantity, touch chosen pad until number in display is same as desired quantity to cook.
(except for DINNER PLATE)
* FORZEN PIZZA *
200g: Touch FROZEN PIZZA once.
300g: Touch FROZEN PIZZA twice within 1.5 seconds.
14
* BEVERAGE * (250ml/cup)
1 cup (mug): Touch BEVERAGE once.
2 cups (mugs): Touch BEVERAGE twice within 1.5 seconds.
3 cups (mugs): Touch BEVERAGEthree times within 1.5 seconds.
NOTE: 1. This setting is good for restoring cooled beverage to a better drinking temperature.
2. Stir after cooking.
15
AUTO COOK (MENU & WEIGHT)
Auto cook allows you to cook or reheat many of your favorite foods by repeatedly touching menu pad.
After the menu selection, touch chosen pad until number in display is same as desired quantity to
cook.
DO THIS THIS HAPPENS
WEIGHT 1 is displayed.
After the 1.5 seconds, the dis-
1. Touch WEIGHT pad. play changed into cooking time
of quantity and the oven starts
cooking.
16
FEEDING BOTTLE
This key is for feeding bottle disinfection effect.
At first, detach the nipple from the bottle and pour the 30cc water into each bottle, arrange the bottle
symmetrically on the glass tray and operate.
* FEEDING BOTTLE *
2 NO (ea.): Touch FEEDING BOTTLE once.
4 NO (ea.): Touch FEEDING BOTTLE twice within 1.5 seconds.
6 NO (ea.): Touch FEEDING BOTTLE three times within 1.5 seconds.
MORE, LESS
MORE pad: adds for 10 seconds to 20 seconds.
LESS pad: remove for 10 seconds to 20 seconds.
These pad only work one touch cooking and feeding bottle mode. And always input previously.
17
INTERLOCK MECHANISM FUNCTIONS AND ADJUSTMENTS
The door lock mechamism is a device has been specially designed to completely eliminate
microwave radiation when the door is opened during operation, and thus to perfectly prevent the dan-
ger resulting from the leakage of microwave.
Adjustment 1.
When the door is closed, the switch button is
pushed by the hook.
The movement of the switch button should exceed
1.2mm measured at the top of the button.
18
(2) Secondary interlock switch and interlock monitor switch
When the door is closed, the hook pushes the push lever down ward, and push lever presses the
button of the interlock monitor swich to bring it under off, condition and presses the button of the
secondary interlock switch to bring it under on, condition.
Adjustment 2.
Interock monitor switch
When the door is closed, the interlock monitor switch should be opend before other switches close.
When the door is closed, the interlock monitor switch should be closed after other switches open.
Secondary interlock switch
The movent of the switch button should exceed 1.2mm measured at the top of the button.
NOTE: Microwave emission test should be performed after adjusting interlock machanism. If the
microwave emission exceed 4mW/cm2, readjust interlock mechanism.
SYMBOL COLOR
RD RED
BL BLUE
BK BLACK
WH WHITE
GN GREEN
19
Cautions to be observed when trouble shooting.
Unlike many other appliances, the microwave oven is a high-voltage, high-current equipment. It is
com pletely safety during normal operation. However, carelessness in servicing the oven can result
in an electeric shock or possible danger from a short circuit.
You are asked to observe the following precautions carefully.
(1) Always remove the power plug from the outlet before servicing.
(2) Use an insulated screwdriver which is attached to iron plate, and wear rubber gloves when servic-
ing the high voltage side.
(3) Warning about the electric charge in the high voltage capacitor. When inspecting and repairing the
high voltage side, always short the capacitor terminals and make sure of discharge.
(4) When the 12 Amp. fuse is blown out to operation of the monitor switch; replace primary, and moni-
tor switch.
Refer to 19 page for the necessary adjustment.
(5) After repair or replacement of parts, make sure that the screws are properly tightened, and all
electrical connections are tightened.
CAUTION: Service personnel should remove their watches whenever working close to or repair-
WARNING: When servicing the appliance, need a care of touching or replacing high potential
parts because of electrical shock of exposing microwave. These parts are as fol-
lowsH.V. Thansformer, Magnetron, H.V. Capacitor, H.V. Diode.
20
1. To remove cabinet.
Remove three screws (F02) on cabinet back.
21
(1) Remove the gasket door (A06) from door plate (A04).
(2) Remove the barrier screen inner (A05) from door plate (A04).
(3) Remove the door frame (A02) from door plate (A04).
(4) Remove the top hinge stopper (A03) from door plate (A04).
(5) Remove the spring (A08) and the hook (A07).
(6) Remove the barrier screem outer (A01) from door frame (A02).
(7) Remove the above steps for reassenbly.
2
NOTE: A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm .
22
23
6. To remove high voltage capacitor.
(1) Remove the screw (F13) which secure the
grounding ring terminal of diode (F16) and
capacitor holder (F14).
(2) Remove the capacitor holder (F14) with
capacitor (F15).
(3) Reverse the above steps for reassembly.
7. To remove magnetron.
(1) Remove three screws (F07) which secure
magnetron (F06).
(2) Pull out the magntron (F06) from the wave
guide.
(3) Reverse the above steps for reassembly.
24
CAUTION: Never install the magnetron without the metallic gasket plate which is packed with
each magnetron to prevent microwave.
Whenever repair work is carried out on magnetron, check the microwave leakage.
9. To remove thransformer.
(1) Remove the four screws (F21) holding the
H.V. tramsformer (F20).
(2) Remove the transformer (F20).
(3) Reverse the above steps for reassembly.
25
10. To remove insulator Heater assembly.
(1) Remove the four HEX NUTS 1.
(2) Remove the insulator Heater assembly 2.
(3) Reverse the above steps for reassembly.
26
TROUBLE SHOOTING GUIDE
Following the procedures below to check if the oven is defective or not.
1. Check grounding before checking trouble.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor. (see page 20)
4. When checking the continuity of switches or of the high voltage transformer, disconnect one lead
wire from these parts and then check cintinuity with the AC plug removed. To do otherwise may
result in false reading ir damage to your meter.
5. Do not touch any part of the circuity on the touch control circuit since static electric discharge may
damage this control panel.
Always touch yourself to ground while working on this panel to discharge any static charge built up
in your body.
First of all operate the microwave oven following the correct operation described in pages 6~20 by
time cooking, in order to find the exact cause if any trouble.
(TROUBLE 1) The following visual conditions indicate a probable defective touch con-
trol circuit or membrane switch assembly.
27
(TROUBLE 2) Digital readout display does not show programming, even if the mem-
brane keyboard is programmed by touching proper pads.
Display does not Check each pad for Normal Malfunction Replace
show programming continuity of the of touch control
at all, even if membrane keyboard control box sub-
keyboard is for the following circuitry of assembly
touched keyboard check control box
NOTE: Before following the particular steps listed above in the trouble shooting guide for the
membrane keyboard, failure, please check for the continuity of each wire-harness
between the membrane keyboard and control box assembly.
Fig. 4
28
2. Type of encoding and pad names.
The membrane keyboard consists of 25 keys whose configurations are described above and provide
11 pad terminations to be connected to the touch control circuit as Fig. 7.
To determine if the membrane keyboard is defective or not, check the continuity of each pad (KEY)
contacts with a multimeter.
29
(TROUBLE3) The oven not operate at all; Display window does not display any figures
and any inputs can not be accepted.
NOTE 1
No
continuity
Approx
80~100
(normal)
NOTE 1: All these switches must be replaced at the same time, please refer to page 18 and 19
for adjustment instructions.
30
Condition Check Result Cause Cause
Defective touch
Normal Replace
control circuit
Malfunction of
Display do not secondary Replace
shown countdown interlock switch
(TROUBLE 4) Display shows all figures selected, but oven does not start cooking,
even though desired program and time are and start pad is taped.
31
Condition Check Result Cause Cause
Turn table
Check continuity No Open winding Replace
motor,
of primary wind- Conntinuity
fan motor and
ing
oven lamp turn
of high voltage
on for a Defective touch
transformer and Replace
second when Normal control circuit
No Check continuity
microwave of connecting wire Continuity
of magnetron.
No
Continuity
Continuity
Continuity
32
(TROUBLE 6) Micrwave Output power is low .
First of all, check if output power is really low following measurement
of the microwave output power on page 34.
Normal
NOTE 2: The following chart shows the timing periods of the RELAY 1.
NOTE 3: Interlock monitor switch must be replaced when fuse is blown out.
33
MEASUREMENT OF THE MICROWAVE OUTPUT POWER
Microwave output power can be checked by indirectly measuring the temperature rise of a certain
amount of water exposed to the microwave as directed below.
Proedure
1. Microwave power output measurement is made with the microwave oven supplied at rated Voltage
and operated at its maximum microwave power setting with a load of 1,0005cc of potable water.
2. The water is contained in a cylindrical borosilicate glass vessel having a maximum material thick-
ness of 3 mm and an outside diameter of approximately 190 mm.
3. The oven and the empty vessel are at ambient temperature prior to the start of the test.
The initial temperature of the water is 102C (503.6F).
It is measured immediately before the water is added to the vessel. After addition of the water to
the vessel, the vessel, the Ioad is immediately placed on the center of the shelf which is in the
Iowest normal position.
4. Microwave power is switched on.
5. Heating time should be exactly 70(KOG-
26XX) or 52(KOG-28XX)seconds.
Heating time is measured while the
microwave generator is operatng at full
power.
The filament heat-up time for magnetrons is
not included.
6. The initial and final water temperatures are
selected so that the maximum difference
betwen the ambient and final water tempera-
tures is 5K.
7. The microwave power output P in watts is calculated from the following formula:
T.t
P=4187X
CAUTION:
1. Water load should be measured exactly to 1 liters.
2. Input power voltage should be exactly 120 volts as specified.
3. Ambient temperature should be 202C (683.6F)
WARNING
Make sure to check the microwave leakage before and after repair or adjustment.
Always, start measuring of an unknown field to assure. Safety for operating personnel from
microwave energy.
Do not place you hands into any suspected microwave radiation field unless the safe density level is
known.
Care should be taken not to place the eyes in direct line with the source of microwave energy.
Slowly approach the unit under test until the radiometer reads an apperaciable microwave leakage
from the unit under the test.
34
Procedure
A) Prepare Microwave Energy Survey Meter, 600cc glass breaker, glass thermometer100C or
212F.
B) Pour 275cc15cc of tap water initially at 205C (689F) in the 600cc beaker with an inside diam-
eter of approx. 8.5 cm (3.5 in).
C) Place it at the center of the tray and set it in a cavity.
D) Close the door and operate the oven.
E) Measure the leakage by using microwave energy survery meter with dual ranges, set to 2,450
MHz.
Measured radiation leakage must not exceed the values prescribed below.
Leakage for a fully assembled oven with door normally closed must be less than 4mW/cm2.
When measuring the leakage, always use the 5cm space cone with probe. Hold the probe per-
pendicular to the cabinet, door. place the
space cone of the probe on the door, cabi-
net, door seam,along the seam, the door
viewing window, the exhaust air vents, the
suction air vents.
Measuring should be in a counter-clock-
wise direction at a rate of 1 inch/sec. If the
leakage of the cabinet door seam is
unknow, move the probe more slowly.
When measuring near a corner of the door, keep the probe perpendicular to the areas making
sure the probe end at the base of the cone does not get closet than 2 inches from any metal.
If it does, erroneous reading may result.
35
WIRING DIAGRAM
36
CIRCUIT DESCRIPTION
Refer to the WIRING DIAGRAM on page 36.
MICROWAVE COOKING
TIME COOKING
1. When the food is placed inside the oven and door is closed.
1) The low voltage transformer supplies the necessary voltage to the touch control circuit when the
power cord is plugged in.
2) The contacts of the interlock monitor switch open.
This switch creates short circuit to blow 12A fuse and stop magnetron oscillation when door is
opened during operation under abnormal condition (i.e. the contacts of primary interlock switch
do not open the circuit).
3) The contacts of primary interlock switch close the primary circuit.
2. When cooking cycle, power and time are set by touching the function pads and the desired
numerical pads.
1) The function indicating bars are located on the digitron light to indicate that function have been
set.
2) The time you set appears in the display window.
3) The touch control circuit memorizes the cooking program you set.
38
Fig. 2
The touch control circuit controls the ON-OFF time of RELAY 1 in order to vary the output power of
the microwave oven from power level 1 to HI (100%) power.
One complete ON and OFF cycle of the RELAY 1 is 29 seconds. The relation between indications
on the control panel and the output of the microwave oven is as shown in Fig. 3
39
OUTPUT POWER
POWER LEVEL RELAY 1 TURN ON, OFF TIME
AGAINST FULL POWER
0 0/29 (0%)
1 3/29 (10%)
2 5/29 (17%)
3 8/29 (28%)
4 11/29 (38%)
5 14/29 (48%)
6 17/29 (59%)
7 20/29 (69%)
8 23/29 (79%)
9 26/29 (90%)
HI 29/29 (100%)
Fig. 3
40
COMPONENT TEST PROCEDURE
1. High voltage is present at the high voltage terminal of the high voltage transformer during any cook-
ing cycle.
3. Before touching any oven components or wiring, always unplug the oven from its power source and
discharge the capacitor (see page 20).
1. High voltage transformer (B) With the ohmmeter set on the highest resis-
(A) Remove connections from the transformer tance scale, measure the resistance across
terminals and check continuity. the diode terminals.
(B) Normal readings should be as follows: Reverse the meter leads and again observe
Secondary winding ..........Approx. 9010% the resistance reading. meter with 6V, 9V or
Filament winding.........................Approx. 0 higher voltage batteries should be used to
Primary winding ..........................Approx. 0 check the front-back resistance of the diode,
otherwise an infinite resistance may be read
2. High voltage capacitor in both directions. A normal diodes resis-
(A) Check continuity of capacitor with meter on tance will be infinite in one direction and sev-
the highest OHM scale. eral hundred K in the other direction.
(B) A normal capacitor will show continuity for a
short time, and then indicate 9M once the 4. Magnetron
capacitor is charged. For complete magnetron diagnosis, refer to
(C) A shorted capacitor will show continuous Measurement of the Microwave Output
continuity. Power. (Page 34) Continuity checks can
(D) An open capacitor will show constant 9M. only indicate and open filament or a shorted
(E) Resistance between each terminal and magnetron. To diagnose for an open fila-
chassis should be infinite. ment or shorted magnetron.
(A) Isolate magnetron from the circuit by dis-
3. High voltage diode conecting the leads.
(A) Isolate the diode from the circuit by discon- (B) A continuity check across magnetron fila-
necting the leads. ment terminals should indicate ohm or less.
(C) A continuity check between each filament
terminal and magnetron case should read
41
SAFETY INTERLOCK CONTINUITY TEST
Disconnect the oven from the power supply.
You can test continuity of safety interlocks and monitor switch by using switch tester or ohmmeter.
The switch operation is checked by the lamp on/off of resistance zero/unlimited.
The sequence of check is interlock monitor switch; primary and secondary interlock switches check.
Make circuits like Fig. a, Fig. b, tests.
(ohmmeter) (ohmmeter)
Fig. a Fig. b
42
PRINTED CIRCUIT BOARD
1. CIRCUIT CHECK PROCEDURE
1) Low Voltage Transformer (DMR-604P) Check.
The low voltage transformer is located on the P.C.B.
NOTE 1: Secondary side voltage of the low voltage transformer changes in proportion to fluctua-
tion of power source voltage.
NOTE 2: The allowable tolerance of the secondary voltage is within 5% of norminal voltage.
2) Voltage Check
Key check point
NO. CHECK POINT REMARK
1 IC1 PIN 6, 10, 11 -5VDC
2 IC1 PIN 1 -20VDC
4 IC1 PIN 8 OR 9
CHECK METHOD
MEASURE POINT
NO. WAVE FORM REMEDY REMARK
Fig. 6
1 MP1 DC -5V0.25 Replace ZD2, EC1, EC2 NO LOAD
2 MP2 DC -30V1.0 Replace R21, ZD3 NO LOAD
3 MP3 DC -27V1.0 Replace R21, R22, EC5 NO LOAD
43
3) Display problems
NO. CAUSE MEASUREMENT RESULT REMEDY
1 Poor contact between Check the voltage Fix the PIN 1 & 25
P.C.B. and display of PIN 1 & PIN 25. 2.4 VAC on the P.C.B.
filament.
44
Fig. 6 Measurement Point
45
CHECK METHOD
POINT A
STAGE
RELAY 2 ON 24VDC
RELAY 2 OFF GND
CHECK METHOD
POINT A B
STAGE
RELAY 1 ON 5VDC 24VDC
RELAY 1 OFF GND GND
5) When the door is opened during operation, the Count down timer does not stop.
CHECK METHOD
POINT A B
STAGE
1) DOOR OPEN OPEN 5VDC
2) DOOR CLOSED CLOSE GND
CHECK
METHOD REMEDY
NO.
46
5) When the digital clock does not operate properly.
POINT WAVEFORM
If clock does not keep exact time, you must check resistor R11, R17.
CHECK METHOD
POINT
A B
STAGE
RELAY 4 ON 5VDC 24VDC
RELAY 4 OFF GND GND
47
2. COMPONENT INFORMATION
1) Transistor
48
3. PRINTED CIRCUITS BOARD
49
4. P.C.B. CIRCUIT DIAGRAM
50
5. P.C.B. LOCATION No.
REF No. PART CODE PART NAME DESCRIPTION REMARK
R10, 13, 18, 26 RD-AZ472J- RESISTOR 4.7 Kohm, 1/6W, 5%
R3 RD-AZ201J- RESISTOR 200 ohm, 1/6W, 5%
R5, 8 RD-AZ203J- RESISTOR 20 Kohm, 1/6W, 5%
R1 RD-AZ105J- RESISTOR 1 Mohm, 1//6W, 5%
R2, 4, 6, 9, 15, 20 RD-AZ102J- RESISTOR 1 Kohm, 1/6W, 5%
R24 RD-4Z510J- RESISTOR 51 ohm, 1/4vW, 5%
R11, 17 RD-AZ473J- RESISTOR 47 Kohm, 1/6w, 5%
R22, 25 RD-2Z560JS RESISTOR 56 ohm, 1/2W, 5%
R23, 14, 19 RD-2Z210JS RESISTOR 150 ohm, 1/2W, 5%
R21 RD-2Z122JS RESISTOR 1.2 Kohm, 1/2W, 5%
D1~7 DZN4148M-- DIODE SWITCHING 1N4148M
D9~15 DZN4002A-- DIODE RECTIFY 1N4002A
ZD1 DZTZ3R9B-- DIODE ZENER 3.9VB, 1/2W
ZD2 DZTZ5R1B-- DIODE ZENER 5.1VB, 1/2W
ZD3 DZTZ20B--- DIODE ZENER 20VB, 1/2W
Q5 TZTC3198GR TRANSISTOR KTC3198GR (1815GR)
Q1, 3, 4, 6 TZTA1270Y- TRANSISTOR KTA1270Y (562Y)
RA1 RA-87X104J RESISTOR ARRAY RGLD6X104J
C4 CCXF1H103Z CAPACITOR CERAMIC HIKF 50V 0.01uF Z
C1~3 CBXF1H104Z CAPACITOR CERAMIC HIKF 50V 0.1uF Z
EC5 CEXF1H471V CAPACITOR ELECTROLYTIC 470uF, 50V, RSS
EC1~2 CEXE1C470A CAPACITOR ELECTROLYTIC 47uF, 16V, RS
EC3 CEXE1H108A CAPACITOR ELECTROLYTIC 0.1uF, 50V, RS
EC4 CEXE1H229A CAPACITOR ELECTROLYTIC 2.2uF, 50V, RS
CA1 CN6XB-102M CAPACITOR ARRAY 1000pF, 2.54MM, M50V
BZ1 3515600100 BUZZER BM-20K
CR1 5PCST400MG RESONATOR CERA CST4.00MGW
CN2 441M36716 CONNECTOR FILM FCZ254-11
CN3 3519150510 CONNECTOR WAFER YW396-05VA
CN1 3519150520 CONNECTOR WAFER YW396-02V
DP1 DSVM5MS06- DIGITRON SVM-5MS06
DPH 3513000500 HOLDER VFD NYLON66
J1~7, 9~12,R16 85801052GY WIRE COPPER 1/0.52 TIN COATING
M145-1 3514311351 PCB MAIN 159.5X82
LVT 5EPV041304 TRANS POWER DMR-604FS
RY1, 4 5SC0101107 RELAY G5J-1-TP-M24V
RY2 5SC0101109 RELAY SW G5B-1 (DC24V) IC IP
IC1 147S811Q00 IC MICOM HD404314B09S
51
EXPLODED AND PARTS LIST
1. Door Assembly
KOG-26XX
REF No. PART CODE PART NAME DESCRIPTION QTY REMARK
3511707300 KOG-3615OS ONLY KOG-261M
DOOR ASSEMBLY 1
3511707310 KOG-3625OS ONLY KOG-262M
3517003000 ONLY KOG-261M
A01 BARRIER-SCREEN *O PMMA 1
3517003020 ONLY KOG-262M
3512202000 ONLY KOG-261M
A02 FARME DOOR ABS 1
3512202010 ONLY KOG-262M
A03 3515201000 STOPPER HINGE *T SCP-1 T2.5 1
A04 3511705510 DOOR WELD AS KOR-64150A 1
A05 3517002810 BARRIER-SCREEN *I PE T0.1 1
A06 3512300200 GASKET DOOR PP 1
A07 3513100700 HOOK POM 1
A08 3515101300 SPRING HOOK PW1 1
KOG-28XX
REF No. PART CODE PART NAME DESCRIPTION QTY REMARK
3511706402 KOR-81150S ONLY KOG-281M
DOOR ASSEMBLY 1
3511706422 KOG-81250S ONLY KOG-282M
3517003100 ONLY KOG-281M
A01 BARRIER-SCREEN *O PMMA T1.5 1
3517003120 ONLY KOG-282M
3512202200 ONLY KOG-281M
A02 FARME DOOR ABS 1
3512202210 ONLY KOG-282M
A03 3515201500 STOPPER HINGE *T SCP-1 T2.5 1
A04 3511705600 KOR-814Q0A ONLY KOG-281M
DOOR WELD AS 1
3511705620 KOR-81250S ONLY KOG-282M
A05 3517002900 BARRIER-SCREEN *I PE T0.1 1
A06 3512300400 GASKET DOOR PP 1
A07 3513100700 HOOK POM 1
A08 3515101300 SPRING HOOK PW1 1
52
2. Control Panel Assembly
KOG-26XX
REF NO. PART CODE PART NAME DESCRIPTION QTY REMARK
CONTROL PANEL AS 1 ONLY KOG-261M
3518514000 KOG-261MOS ONLY KOG-261M
B01 SWITCH MEMBRANE 1
3518514800 KOG-262MOS ONLY KOG-261M
3516710900 KOG-361QOS ABS ONLY KOG-261M
B02 CONTROL PANEL 1
3516710710 KOG-262QOS ABS ONLY KOG-262M
B03 PKMPMSSA00 PCB MAIN AS KOG-261QOS 1
B04 7621401211 SCREW TAPPING T2S PAN 4X12 PW MFZN 3
B05 3513701400 LEVERL DOOR OPEN POM 1
B06 441B655072 SPRING DOOR BUTTON HSWR 1
3516903600 ONLY KOG-261M
B07 BUTTON DOOR OPEN ABS 1
3516903620 ONLY KOG-262M
KOG-28XX
REF No. PART CODE PART NAME DESCRIPTION QTY REMARK
PKCPSWTT00 KOG-281MOA ONLY KOG-281M
CONTROL PANEL AS 1
ONLY KOG-282M
ONLY KOG-281M
B01 3518514100 SWITCH MEMBRANE KOG-281MOS 1
ONLY KOG-282M
3516710900 KOG-281MOS ONLY KOG-281M
B02 CONTROL PANEL 1
3516710910 KOG-282MOS ONLY KOG-282M
B03 PKMPMSTA00 PCB MAIN AS KOG-281MOS 1
B04 7821401211 SCREW TAPPING T2SPAN 4X12 PW MFZN 3
B05 3513701400 LEVERL DOOR OPEN POM 1
B06 441B655072 SPRING DOOR BUTTON HSWR 1
3518903600 ONLY KOG-281M
B07 BUTTON DOOR OPEN ABS 1
3516903620 ONLY KOG-282M
53
54
REF No. PART CODE PART NAME DESCRIPTION QTY REMARK
3510801300 ONLY KOG-26XX
F01 CABINET PCM T0.6 1
3510801400 ONLY KOG-26XX
F02 7S312X4081 SCREW TAPPING T1 TRS 4X8 SE MFZN 3
3516105010 KOG-381QOS 1 ONLY KOG-26XX
F03 CAVITY WELD AS
3516104910 KOG-361QPS 1 ONLY KOG-26XX
F04 7S342X40B1 SCREW SPECIAL T2S TRS 4X12 SE MFZN 2
F05 7X342X40B1 SCREW SPECIAL T2S TRS 4X12 SE MFZN 1
F06 4413A90012 CLAMP POWER CORD 66 NYLON 1
F07 7112400811 SCREW TAPPING T1 TRS 4X8 MFZN 3
F08 35113NBND5 CORD POWER AS 3X0.75 60X60X200 RTML 1
F09 3518002200 MAGNETRON 2M218H(MF)I 1
F10 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 3
F11 7112400811 SCREW TAPPING T1 TRS 4X8 MFZN 2
F12 7172400811 SCREW TAPTITE TT1 TRS 4X8 MFZN 2
F13 3511402500 COVER*B SBHG T0.8 1
F14 3963820110 MOTOR SHADED POLE 120V 17W MW10XA-R01 1
F15 3511800300 FAN PP+30% GLASS 1
F16 7172400811 SCREW TAPTITE TT2 TRS 4X8 MFZN 1
F17 3513001900 HOLDER HV CAPACITOR SECC T0.8 1
44IL267010 2100VAC 0.7F 1 ONLY KOG-26XX
F18 CAPACITOR HV
3518300800 2100VAC 0.82F 1 ONLY KOG-26XX
F19 4416V24000 DIODE HV HVR-1X-32B(D5.3) 1
3518106640 JY-N60A0-61T ONLY KOG-26XX
F20 TRANS HV 1
518106910 DH-N80A0-81T ONLY KOG-28XX
F21 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 4
F22 3512100900 FOOT PP DASF-130 2
3510308700 ONLY KOG-26XX
F23 BASE SBHG T0.8 1
3510308900 ONLY KOG-26XX
F24 7172400811 SCREW TAPTITE TT2 TRS 4X8 MFZN 2
F25 7112401011 SCREW TAPPING T1 TRS 4X10 FMZN 6
F26 3515201100 STOPPER HINGE *U SCP-1 T2.5 1
F27 5S762S10G0 SW MICRO V16-FA-63 SPNO #187 1
F28 5S762M10G0 SW MICRO V16-FA-62 SPNC #187 1
F29 5S762S10G0 SW MICRO V16-FA-63 SPNO #187 1
F30 3513701300 LEVER LOCK POM 1
55
REF No. PART CODE PART NAME DESCRIPTION QTY REMARK
F31 3513805700 LOCK POM BLACK 1
F32 3513601500 LAMP BL 125V 25W T25 C7A H1 1
F33 7121400811 SCREW TAPPING T2S PAN 4X8 MFZN 2
F34 3966820200 MOTOR SYNCRO 120V 2W GM-16-12F17 1
F35 3515201500 STOPPER HINGE *T AS KOR-61150OS 1
F36 3517400600 COUPLER PPS 1
F37 3511403500 COVER WAVEGUIDE MICA 1
F38 4078502031 BUTTOM LOCKING PP HONAM A 353 2
3513301450 KOG-261QOA 1 ONLY KOG-26XX
F39 INSULATOR HEATER AS
3513301430 KOG-281Q0A 1 ONLY KOG-28XX
F39-1 3512802300 HEATER 1000W 120V 1
F39-2 3513301100 INSULATOR HEATER SPP T0.8 1
F40 3514700900 ROLLER TEFLON 3
F41 3512509200 GUIDE ROLLER PP 1
3517203600 GLASS 1 ONLY KOG-28XX
F42 TRAY
3517203500 GLASS 1 ONLY KOG-28XX
F43 7172400811 SCREW TAPTITE TT2 TRS 4X8 MFZN 2
3517204410 KOG-361QOS 100 MM 1 ONLY KOG-28XX
F44 TRAY RACK AS
3517201800 KOR-1825OS 120MM 1 ONLY KOG-28XX
F45 7292500411 NUT SUS M5 2
F46 7279300611 SCREW TAPTITE TT2 TRS 3X6 MFZN 1
F47 3518902200 THERMOSTAT OFF:130 ON:115 1
F48 7S627W50X1 NUT HEX M5 FLANGE 2
F49 3512711310 HARNESS MAIN KOG-281QOA 1
F50 7172400811 SCREW TAPTITE TT2 TRS 4X8 MFZN 1
B00 CONTROL PANEL AS REFER TO EXPLODED VIEW page 54
A00 DOOR AS REFER TO EXPLODED VIEW page 53
56
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG, MAPO-GU,
SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: DAEWOOELEC
FAX: 02) 364-5588/5305
TEL: 02) 360-7114/7315~7