Professional Documents
Culture Documents
F0354856 PDF
F0354856 PDF
Abstract : - Solar energy has experienced phenomenal growth in recent years due to both technological
improvements resulting in cost reductions and government policies supportive of renewable energy
development and utilization. This study analyzes the technical, economic and policy aspects of solar energy
development and deployment. While the cost of solar energy has declined rapidly in the recent past, it still
remains much higher than the cost of conventional energy technologies. Like other renewable energy
technologies, solar energy benefits from fiscal and regulatory incentives and mandates, including tax credits and
exemptions, feed-in-tariff, preferential interest rates, renewable portfolio standards and voluntary green power
programs in many countries. Potential expansion of carbon credit markets also would provide additional
incentives to solar energy deployment; however, the scale of incentives provided by the existing carbon market
instruments, such as the Clean Development Mechanism of the Kyoto Protocol, is limited. Despite the huge
technical potential, development and large-scale, market-driven deployment of solar energy technologies world-
wide still has to overcome a number of technical and financial barriers. Unless these barriers are overcome,
maintaining and increasing electricity supplies from solar energy will require continuation of potentially costly
policy support.
Indexing terms/
Keywords: - solar energy; renewable energy economics and policies; climate change EARTH, gion, energy
efficiency,green communications,femtocells, interference,radio resource management.
I. INTRODUCTION
Solar energy has experienced an impressive technological shift. While early solar technologies
consisted of small-scale photovoltaic (PV) cells, recent technologies are represented by solar concentrated
power (CSP) and also by large-scale PV systems that feed into electricity grids. The costs of solar energy
technologies have dropped substantially over the last 30 years. For example, the cost of high power band solar
modules has decreased from about $27,000/kW in 1982 to about $4,000/kW in 2006; the installed cost of a PV
system declined from $16,000/kW in 1992 to around $6,000/kW in 2008 (IEA-PVPS, 2007; Solarbuzz, 2006,
Lazard 2009). The rapid expansion of the solar energy market can be attributed to a number of supportive policy
instruments, the increased volatility of fossil fuel prices and the environmental externalities of fossil fuels,
particularly greenhouse gas (GHG) emissions.
Theoretically, solar energy has resource potential that far exceeds the entire global energy demand
(Kurokawa et al. 2007; EPIA, 2007). Despite this technical potential and the recent growth of the market, the
contribution of solar energy to the global energy supply mix is still negligible (IEA, 2009). This study attempts
to address why the role of solar energy in meeting the global energy supply mix continues to be so a small.
What are the key barriers that prevented large-scale deployment of solar energy in the national energy systems?
What types of policy instruments have been introduced to boost the solar energy markets? Have these policies
produced desired results? If not, what type of new policy instruments would be needed?
A number of studies, including Arvizu et al. (2011), have addressed various issues related to solar
energy. This study presents a synthesis review of existing literature as well as presents economic analysis to
examine competitiveness solar energy with fossil energy counterparts. Our study shows that despite a large drop
in capital costs and an increase in fossil fuel prices, solar energy technologies are not yet competitive with
www.ajer.org Page 48
American Journal of Engineering Research (AJER) 2014
conventional technologies for electricity production. The economic competitiveness of these technologies does
not improve much even when the environmental externalities of fossil fuels are taken into consideration.
Besides the economic disadvantage, solar energy technologies face a number of technological, financial and
institutional barriers that further constrain their large-scale deployment. Policy instruments introduced to address
these barriers include feed in tariffs (FIT), tax credits, capital subsidies and grants, renewable energy portfolio
standards (RPS) with specified standards for solar energy, public investments and other financial incentives.
While FIT played an instrumental role in 3
Solar energy represents our largest source of renewable energy supply. Effective solar irradiance reaching the
earths surface ranges from about 0.06kW/m2 at the highest latitudes to 0.25kW/m2 at low latitudes. Figure 1
compares the technically feasible potential of different renewable energy options using the present conversion
efficiencies of available technologies. Even when evaluated on a regional basis, the technical potential of solar
energy in most regions of the world is many times greater than current total primary energy consumption in
those regions (de Vries et al. 2007).
www.ajer.org Page 49
American Journal of Engineering Research (AJER) 2014
photovoltaic (PV) and (ii) solar thermal. The PV technology converts radiant energy contained in light
quanta into electrical energy when light falls upon a semiconductor material, causing electron excitation and
strongly enhancing conductivity (Sorensen, 2000). Two types of PV technology are currently available in the
market: (a) crystalline silicon-based PV cells and (b) thin film technologies made out of a range of different
semi-conductor materials, including amorphous silicon, cadmium-telluride and copper indium gallium
diselenide1. Solar thermal technology uses solar heat, which can be used directly for either thermal or heating
application or electricity generation. Accordingly, it can be divided into two categories: (i) solar thermal non-
electric and (ii) solar thermal electric. The former includes applications as agricultural drying, solar water
heaters, solar air heaters, solar cooling systems and solar cookers2 (e.g. Weiss et al., 2007); the latter refers to
use of solar heat to produce steam for electricity generation, also known as concentrated solar power (CSP).
Four types of CSP technologies are currently available in the market: Parabolic Trough, Fresnel Mirror, Power
Tower and Solar Dish Collector (Muller-Steinhagen and Trieb, 2004; Taggart 2008a and b; Wolff et al., 2008).
Solar energy technologies have a long history. Between 1860 and the First World War, a range of technologies
were developed to generate steam, by capturing the suns heat, to run engines and irrigation pumps (Smith,
1995). Solar PV cells were invented at Bell Labs in the United States in 1954, and they have been used in space
satellites for electricity generation since the late 1950s (Hoogwijk, 2004). The years immediately following the
oil-shock in the seventies saw much interest in the development and commercialization of solar energy
technologies. However, this incipient solar energy industry of the 1970s and early 80s collapsed due to the sharp
decline in oil prices and a lack of sustained policy support (Bradford, 2006). Solar energy markets have regained
momentum since early 2000, exhibiting phenomenal growth recently. The total installed capacity of solar based
electricity generation capacity has increased to more than 40 GW by the end of 2010 from almost negligible
capacity in the early nineties (REN21, 2011).Germany and Spain, a mix of policy portfolios that includes federal
tax credits, subsidies and rebates, RPS, net metering and renewable energy certificates (REC) facilitated solar
energy market growth in the United States. Although the clean development mechanism (CDM) of the Kyoto
Protocol has helped the implementation of some solar energy projects, its role in promoting solar energy is very
small as compared to that for other renewable energy technologies because of cost competitiveness. Existing
studies we reviewed indicate that the share of solar energy in global energy supply mix could exceed 10% by
2050. This would still be a small share of total energy supply and a small share of renewable supply if the
carbon intensity of the global energy system were reduced by something on the order of 75%, as many have
argued is necessary to stem the threat of global warming.
The paper is organized as follows. Section 2 presents the current status of solar energy technologies,
resource potential and market development. This is followed by economic analysis of solar energy technologies,
including sensitivities on capital cost reductions and environmental benefits in Section 3. Section 4 identifies the
technical, economic, and institutional barriers to the development and utilization of solar energy technologies,
followed by a review of existing fiscal and regulatory policy approaches to increase solar energy development in
Sections 5 and 6, including potential impacts of greenhouse gas mitigation policies on the deployment of solar
energy technologies.
In green radio communications, a main network design objective is to reduce the amount of energy
consumption while maintaining satisfactory quality of service (QoS). Two motivations are behind this design
criterion. One is the service providers financial considerations. Almost half of a mobile service providers
annual operating expenses are energy costs [1]. Each base station(BS) in a cellular network consumes roughly
upto 2.7 kWh of electrical power [2]. With densely deployed BSs to achieve wide area coverage, high energy is
consumed per annum. Such high energy consumption of green radio communications network
design:environmental considerations. Currently, the telecommunication industry is responsible for about 2
percent of CO2 emissions, and given the industrys growth it could increase to 4 percent by 2020 [3]. As a
result, political initiatives start to put requirements on ope CO2 emissions of communication networks [4].In
Europe, companies such as Orange (France),Ericson (Sweden), and Vodafone (United Kingdom)aim to reduce
their CO2 emissions by 5080 percent by 2020 [5]. Hence, the reduction of energy consumption in the
telecommunication
industry sector will result in a positive impact on both the environment and operators profits [1].In the
literature, there have been several proposals for designing an energy-aware infrastructure in wireless
communications networks.In the following, energy saving techniques at the network level are discussed. The
limitations of the existing techniques are pointed out. We investigate network cooperation as a means of energy
saving in green radio communications.
The objective is to develop a framework that enables networks with overlapped coverage in a given
geographical region to cooperate with each other to achieve energy saving.
www.ajer.org Page 50
American Journal of Engineering Research (AJER) 2014
II. RENEWABLE ENERGY SOURCES
From an environmental perspective, the objective of green radio communications is to reduce CO2
emissions [6]. This can be achieved by using renewable energy sources at the BSs, such as locally generated
wind and solar power. This can reduce the amount of electrical power consumption taken from the grid. Also, it
can complement the fossil fuel power generators in off-grid sites. Moreover,air cooling and cold climates can be
used to cool the electronic devices in the BSs [6]. However, the renewable energy sources cannot replace the
traditional energy sources in the BSs due to their
required high reliability, since any power shortage will disturb the wireless networks service provision.
Green Manufacturing
The greening process would involve using eco-friendly components, energy efficient manufacturing
equipment, electronic and mechanical waste recycling and disposal, reduction in use of hazardous substances
like chromium, lead and mercury and reduction of harmful radio emission.
Waste Disposal
Disposal of mobile phones, network equipment etc., in an environment-friendly manner so that any toxic
material used during production does not get channelized into the atmosphere or underground water
www.ajer.org Page 51
American Journal of Engineering Research (AJER) 2014
1. Proper radio planning to reduce number of Base transceiver stations
2. Sharing of backhaul network
3. Sharing of passive and active infrastructure
4. Replacing air-conditioners with forced air cooling
5. HFC free cooling systems
6. Installing outdoor base-stations
7. Using energy efficient technology and renewable energy resources
www.ajer.org Page 52
American Journal of Engineering Research (AJER) 2014
mean the chosen BS is the one which receives the mobile at best quality. In other words, it is not necessarily the
one which requires minimal UL transmission power and respective exposure to radiation. This is especially true
in case the base stations employ multiple antennas. With multiple antennas, a large variety of transmission and
reception schemes is available. Each scheme exploits the MIMO channel differently which often results in
significantly different link quality.
Green charger
Figure 5 shows a green charger using solar cells. Each set of three solar cells develops about 2.0 volts
across itself when in full sunlight. The string of 6 solar cells puts out around 4V with no load. When the solar
cells are connected to the battery (a 3.7V), a current will flow which will charge the battery.
The 6 solar cell panel with diode is the recommended circuit. The diode prevents the battery from discharging
through the cells at night and the 6th cell boosts the voltage up enough to compensate for the voltage drop
across the diode. For a 6 solar cell panel, connect jumper J2 and disconnect J1.
www.ajer.org Page 53
American Journal of Engineering Research (AJER) 2014
are going on to explore specific applications of these technologies in smart grid environment. Figure 6 shows
the Smart Grid Technology for wireless communication.
Various smart grid applications can be achieved through standardized wireless communication technologies, e.g.
IEEE 802.11 based wireless LAN, IEEE 802.16 based WiMAX, 3G/4G cellular, ZigBee based on IEEE 802.15,
IEEE 802.20 based MobileFi, etc.
Smart grid will be characterized by two-way flow of power in electrical network, and information in
communication network. In the recent report on National Institute of Standard and Technology framework and
roadmap for smart grid interoperability standards, several wired and wireless communication technologies are
identified for smart grid. Advanced wireless systems offer the benefits of inexpensive products, fast deployment,
low cost installations, widespread access, and mobile communications which wired and even the older wireless
technologies often cannot provide. However, in the past, wireless technologies had comparatively slow
www.ajer.org Page 54
American Journal of Engineering Research (AJER) 2014
acceptance in power industries due to low data rates, interference related issues, security concerns, limited
product availability, etc. Several activities have already been initiated to address the wireless technical issues,
and identify suitable wireless technologies particularly for smart grid. In the latest Electric Power Research
Institute report to NIST on the smart grid interoperability standards roadmap, one of the suggested prioritized
actions is to address the Communications Interference in Unlicensed Radio Spectrum. The success of this
action would alleviate many issues related to wireless communication in unlicensed radio spectrum by providing
a dedicated communication channels for the mission-critical inter-operations of the smart grid. With these
motivations from recent developments and ongoing activities, the efforts have been carried out in this work to
present the various smart applications using standardized wireless communication technologies, e.g. IEEE
802.11 based wireless LAN, IEEE 802.16 based WiMAX, 3G/4G cellular, ZigBee based on IEEE 802.15, IEEE
802.20 based MobileFi, etc. Different applications of these wireless technologies have been identified
considering the latest available data rates, distance coverage, and other important technology features in smart
grid environment
IV. CONCLUSION
The need to develop green wireless communication systems turns out to be more and more vital as
wireless networks are becoming ubiquitous. Green Wireless Communication will provide energy efficient
communication. It will result into less radiation from devices as well as more economic solutions for service
providers and subscriber. Green wireless communication is the part of Corporate Social Responsibility which
strives to reduce carbon footprint and Green house gases to provide Green ICT services to customers.
Governmentshould also form rules and regulations to certify a service provider as Green service provider. The
integration of different energy efficient technologies like Green BTS, Green manufacturing, Green Handover,
Green antennas, Green electronics and Smart Grid solution will create accord between human being and nature
V. REFERENCES
[1]. Vikram Chandrasekhar and Jeffrey G. Andrews, Alan Gatherer, Texas Instruments Femtocell Networks:
A Surveycommunication magazine,IEEE,vol.46,pp.59-67,sept 2012
[2]. Shuguang Cui, Andrea J. Goldsmith, and Ahmad Bahai, Energy-constrained Modulation
OptimizationIEEE Trans.wireless commun.,vol.4,no.5,pp.2349-2360,sept.,2011
[3]. Qing Chen and Mustafa Cenk Gursoy Energy Efficiency Analysis in Amplify-and-Forward and Decode-
and-Forward Cooperative Networksinformation sceinse and systems.53rd annual conference on
,vol.no.pp.811-816
[4]. Qing Chen and Mustafa Cenk GursoEnergy-Efficient Modulation Design for Reliable Communication
in Wireless NetworksWCNC,2011 IEEE.,vol.no.,pp.1-6,18-21 april 2011
[5]. Albrecht J. Fehske, Fred Richter, and Gerhard P. Fettweis Energy Efficiency Improvements through
Micro Sites in Cellular Mobile Radio NetworksPIMPRC 2011 IEEE 46 TH INTERNATIONAL
SYNOPSYM on,vol.,no.pp1-6,april 2010
[6]. Muhammad Ismail and Weihua Zhuang Network Cooperation for Energy Saving in Green Radio
Communicationswireless communication,IEEE vol no.48.,no.11,pp.no.66-72,nov.2011
[7]. Aria nosratinia, dallas, todd E. Hunter Green technology in cooperative communication network using
coded cooperative method IEEE communication magazine vol.no.4,october 2013
[8] India: Greenhouse Gas Emissions 2007. (2010) Ministry of Environment and Forests, Govt. of India
Sanjay kumar was born on 2nd may 1989 in India . He received B.E degree in
Electronics Engineering from Madhav institute of technology and science(MITS)
Gwalior,India in 2011. He is currently studying M.E Degree in Electronics and
Telecommunication Engineering from S.G.S.I.T.S indore, India his research interest in
wireless communication
www.ajer.org Page 55
American Journal of Engineering Research (AJER) 2014
Mrs. S.V Charhate was born on 14th may 1958 in India. She received B. E degree in
Electronics and Telecommunication Engineering from college of engineering pune and
M.E degree in computer science engineering from Shri G. S. institute of technology and
science, indore . she has teaching experience of 26 years and currently Professor in the
Department of Electronics and Telecommunicatio and Dean of Admn. In Shri G.S
institute of technology and science indore, india . she has published papers in Nationa and
International journals. Conferences and workshops organizsd by IEEE ,IETE and ISTE.
Her research interest area in wireless communication.
Mrs. Jaya diptilal was born on 1st march 1977 in India. She received B.E degree(2002)
in Electronics and Telecommunication from Jabalpur engineering college ,Jabalpur. And
M.E degree(2005) from Jabalpur engineering college, Jabalpur . she has teaching
experience of 7 years . she has published many papers in National and International
Conferences, journals . her research interest area in cooperative communication ,and
green communication in cooperative radio network.
www.ajer.org Page 56