Professional Documents
Culture Documents
Micro Wave Oven Repair Guide PDF
Micro Wave Oven Repair Guide PDF
com
e-mail http://www.lgeservice.com/techsup.html
MICROWAVE OVEN
SERVICE MANUAL
MODEL: MV1526W
MV1526B
CAUTION
BEFORE SERVICING THE UNIT, READ THE
SAFETY PRECAUTIONS IN THIS MANUAL.
CAUTION
SAFETY PRECAUTIONS
a. Do not operate or allow the oven to be operated with the door open.
b. Make the following safety checks on all ovens to be serviced before activating the
magnetron or other microwave source, and make repairs as necessary; (1) Interlock
operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and
other damage), (4) damage to or loosening of hinges and latches, (5) evidence of
dropping or abuse.
c. Before turning on microwave power for any service test or inspection within the
microwave generating compartments, check the magnetron, wave guide or
transmission line, and cavity for proper alignment, integrity, and connections.
d. Any defective or misadjusted components in the interlock, monitor, door seal, and
microwave generation and transmission systems shall be repaired, replaced, or
adjusted by procedures described in this manual before the oven is released to the
owner.
e. A Microwave leakage check to verify compliance with the CSA Standard should be
performed on each oven prior to release to the owner.
Proper
operation of the microwave ovens requires that the magnetron be assembled to the
wave guide and cavity. Never operate the magnetron unless it is properly installed.
Be sure that the magnetron gasket is properly installed around the dome of the tube whenever
installing the magnetron.
Untrained
personnel should not attempt service without a thorough review of the test
procedures and safety information contained in this manual.
FOREWORD
Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing
yourself to the Microwave Energy normally contained within the oven cavity.
TABLE OF CONTENTS
(Page)
SAFETY PRECAUTIONS ......................................................................................................... Inside front page
SPECIFICATIONS.......................................................................................................................................... 1-1
CAUTIONS ..................................................................................................................................................... 2-1
INSTALLATION .............................................................................................................................................. 3-1
OPERATING INSTRUCTIONS....................................................................................................................... 4-1
CONTROL PANEL ................................................................................................................................. 4-1
CONTROL PANEL INSTRUCTIONS ..................................................................................................... 4-2
OVERALL CIRCUIT DIAGRAM...................................................................................................................... 5-1
SCHEMATIC DIAGRAM......................................................................................................................... 5-1
MATRIX CIRCUIT FOR TOUCH KEY BOARD ...................................................................................... 5-2
GENERAL INFORMATION FOR SERVICE ................................................................................................... 6-1
GENERAL PRECAUTIONS IN USE ...................................................................................................... 6-1
TRIAL OPERATION ............................................................................................................................... 6-1
FEATURES AND SPECIFICATIONS FEATURES................................................................................. 6-1
SERVICE INFORMATION ............................................................................................................................. 7-1
PRECAUTIONS AND REPAIR SERVICE TIPS ..................................................................................... 7-1
MICROWAVE LEAKAGE TEST ............................................................................................................. 7-2
POWER OUTPUT MEASUREMENT ..................................................................................................... 7-3
DISASSEMBLY INSTRUCTIONS .......................................................................................................... 7-4
INTERLOCK SYSTEM .......................................................................................................................... 7-12
INTERLOCK CONTINUITY TEST .......................................................................................................... 7-14
TEST AND CHECKOUT PROCEDURES AND TROUBLE SHOOTING................................................ 7-15
A. TEST PROCEDURES................................................................................................................ 7-15
B. CHECKOUT PROCEDURES..................................................................................................... 7-18
C. TROUBLE SHOOTING .............................................................................................................. 7-21
EXPLODED VIEW .......................................................................................................................................... 8-1
REPLACEMENT PARTS LIST ............................................................................................................... 8-8
SCHEMATIC DIAGRAM OF PCB .......................................................................................................... 8-12
PRINTED CIRCUIT BOARD .................................................................................................................. 8-13
PCB PARTS LIST................................................................................................................................... 8-14
SPECIFICATIONS
Rated Power Consumption..................................................1,500W maximum (Microwave oven+Cook top lamps+Ventilation fan)
Microwave Output.................................................................1,000W (IEC 60705)
Adjustable 100W through 1000W, 10 steps
Frequency .............................................................................2,450 MHz 50 MHz
Power Supply........................................................................120 VAC, 60 Hz
Rated Current .......................................................................13 Amp. (Microwave oven+Cook top lamps+Ventilation fan)
Magnetron Cooling ...............................................................Forced Air Cooling
Rectification...........................................................................Rectification Voltage Double Half-Wave
Door Sealing .........................................................................Choke System
Safety Devices......................................................................Oven Cavity Thermostat:
Open at 90C 5C
Fuse(20A)
Primary Interlock Switch
Secondary Interlock Switch
Interlock Monitor
Magnetron.............................................................................2M214-39F
High Voltage Capacitor ........................................................Capacitor: 1.0F, 2.1 KV AC
High Voltage Diode...............................................................Diode; 350mA, 9.0 KV
Cook top Lamp .....................................................................125 V, 30 W
Cavity Lamp..........................................................................125 V, 30 W
Timer .....................................................................................Digital, up to 99 mim. 99 sec. (in each cooking stage)
Tray .......................................................................................Tempered Safety Glass
Overall Dimensions ..............................................................2915/16(W)x167/16(D)x153/8(H)
Oven Cavity Size .................................................................197/8(W)x143/16(D)x815/16(H)
Effective Capacity of Oven Cavity .......................................1.5 Cu.ft.
Accessories...........................................................................Owners Manual & Cooking Guide, Installation Manual,
Exhaust Adapter, Exhaust Damper, Mounting Kit and Two Filters,
Rotating Ring Assembly.
1-1
CAUTIONS
Unlike other appliances, the microwave oven is
high-voltage and high-current equipment.
MICROWAVE RADIATION
Though it is free from danger in ordinary use, Personnel should not be exposed to the
extreme care should be taken during repair. microwave energy which may radiate from the
magnetron or other microwave generating
device if it is improperly used or connection.
DO NOT operate on a 2-wire extension cord during All input and output microwave connections,
repair and use. waveguide, flange, and gasket must be secure.
NEVER TOUCH any oven components or wiring during Never operate the device without a microwave
operation. energy absorbing load attached.
BEFORE TOUCHING any parts of the oven, always Never look into an open waveguide or antenna
remove the power plug from the outlet. while the device is energized.
For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must discharge the high Proper operation of the microwave oven requires that
voltage capacitor by shorting across the two terminals the magnetron be assembled to the waveguide and
with an insulated screwdriver. cavity. Never operate the magnetron unless it is
properly installed.
Be sure that the magnetron gasket is properly
installed around the dome of the tube whenever
installing the magnetron.
ANTENNA
Gasket
COOLING FIN
FILAMENT
TERMINALS
MAGNETRON
CHASSIS GROUND
Remove your watch whenever working close to or MAGNETRON
replacing the Magnetron.
DO NOT touch any parts of the control panel circuit. A
resulting static electric discharge may damage this
P.C.B.
NEVER operate the oven with no load. THE OVEN IS TO BE SERVICED ONLY
NEVER injure the door seal and front plate of the oven BY PROPERLY QUALIFIED SERVICE
cavity.
PERSONNEL.
NEVER put iron tools on the magnetron.
NEVER put anything into the latch hole and the interlock
switches area.
2-1
INSTALLATION
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
PRECAUTIONS ON INSTALLATION
A. Plug the power supply cord into a 120V AC, 60Hz,
single-phase power source with a capacity of 15A
or 20A.
B. Avoid placing the unit in a location where there is
direct heat or splashing water.
C. Install the unit on the mounting plate firmly.
D. Place the unit as far away as possible from TV,
radio, etc. to prevent interference.
GROUNDING INSTRUCTIONS
For personal safety, this appliance must be fully
grounded at all times.
In the event of an electrical short circuit, grounding
reduces the risk of electrical shock.
The plug must be plugged into an outlet that is
properly installed and grounded.
CAUTION
This unit is equipped with a 3-prong plug for your
safety. If the wall outlet is a grounded 3-hole type,
the unit will be grounded automatically.
Properly Polarized
and Grounded
Outlet
WARNING
Improper use of the grounding plug can result in a
risk of electric shock.
Do not, under any circumstances, cut or remove the
third ground prong from the power cord plug.
3-1
OPERATING INSTRUCTIONS
CONTROL PANEL
4
3
5 7
8 10
11
12 13
14 16
15 18
17
21
19
20
4-1
CONTROL PANEL INSTRUCTIONS
1. DISPLAY: The Display includes a clock and indicators to 12. TIME COOK: Touch this pad to set a cooking time.
tell you time of day, cooking time settings and cooking
functions selected. 13. POWER LEVEL: Touch this pad to select a cooking
power level.
2. POPCORN: Touch this pad when popping popcorn in
your microwave oven. 14. CUSTOM SET: Touch this pad to change the ovens
default settings for sound, clock, display speed, defrost
3. POTATO: Touch this pad to cook potatoes from 1 to 4. weight, and demo mode operations.
4. BEVERAGE: Touch this pad to reheat one cup or two 15. KITCHEN TIMER: Touch this pad to set the kitchen
cups a beverage. timer.
5. PIZZA: Touch this pad to reheat 1 to 3 slices. 16. CLOCK: Touch this pad to enter the time of day.
6. TIME DEFROST: Touch this pad to defrost most other 17. FAN HI/LO/OFF: Touch this pad to turn the fan on or off.
frozen foods.
18. LIGHT HI/LO/OFF: Touch this pad to turn on the
7. FROZEN ENTREE: Touch this pad to cook frozen entrees cooktop/countertop light.
by choosing a preset weight.
19. STOP/CLEAR: Touch this pad to stop the oven or clear
8. AUTO COOK: Touch this pad to cook vegetables, rice, or all entries.
casseroles.
20. EZ ON: Touch this pad to set and start quickly at 100%
9. AUTO REHEAT: Touch this pad to reheat dinner plate, power level.
soup/sauce, casserole, roll/muffin.
21. START: Touch this pad to start a function. If you open
10. AUTO DEFROST: Meat, poultry, fish. Touch on pad to the door after oven begins to cook, retouch START.
select food type and defrost food by weight.
4-2
OVERALL CIRCUIT DIAGRAM
SCHEMATIC DIAGRAM
5-1
MATRIX CIRCUIT FOR TOUCH KEY BOARD
AUTO TIME
COOK COOK
KITCHEN
CLOCK Ez On
TIMER
TIME POWER
N.C
DEFROST LEVEL
STOP/ N.C
CLEAR
5-2
GENERAL INFORMATION FOR SERVICE
GENERAL PRECAUTIONS IN USE FEATURES AND SPECIFICATIONS
A. Never operate the unit when it is empty.
FEATURES
Operating the oven with no load may shorten the A. The safety systems incorporated in this model are:
life of the magnetron. Whenever cooking dry foods (1) Primary interlock switch
(dried fish, bread, etc.) or a small amount of food, (2) Secondary interlock switch
be sure to put a glass of water into the cooking (3) Interlock monitor switch
compartment. The glass turntable may become hot (4) Choke system
after operating, be careful when touching it. (5) Magnetron thermal fuse
B. Aluminum foil should be avoided because it will (6) Oven cavity thermostat
disrupt cooking and may cause arcing. However, (Note: This thermostat located on the oven
small pieces may be used to cover some parts of cavity will open and stop the unit from operation
food to slow the cooking. Any aluminum foil used only if a high temperature is reached, such as,
should never be closer than 2.5 cm to any side wall a fire created by overcooking food.)
of the oven. B. Any one of 10 power output levels ranging 100W to
1000W can be selected by the touch control and
TRIAL OPERATION electronic computer system.
After installation, the following sequences and results
should be checked carefully.
6-1
SERVICE INFORMATION
PRECAUTIONS AND REPAIR SERVICE TIPS
PRELIMINARY
A. SINCE NEARLY 2,100 VOLTS EXISTS IN SOME (3) Do not operate the unit until it is completely
CIRCUITS OF THIS UNIT REPAIRS SHOULD BE repaired, if any of the following conditions exist.
CARRIED OUT WITH GREAT CARE. The unit must not be operated.
The filament leads of magnetron carry High (a) The door does not close firmly.
Voltage with respect to ground. Extreme caution (b) The hinge is broken.
must be exercised. Never plug the unit into a (c) The door seal is damaged.
power source to determine which component is (d) The door is bent or warped, or there is any
defective in high voltage section. other visible damage on the unit that may
cause microwave energy leakage.
B. TO AVOID POSSIBLE EXPOSURE TO NOTE: Always keep the seal clean.
MICROWAVE ENERGY LEAKAGE, THE (e) Make sure that there are no defective parts
FOLLOWING PRECAUTIONS MUST BE TAKEN in the interlock mechanism.
BEFORE SERVICING. (f) Make sure that there are no detective parts
(1) Before the power is applied: in the microwave generating and transmission
(a) Make sure the primary interlock switch, the assembly (especially waveguide).
secondary interlock switch and the interlock
monitor switch operate properly by opening (4) The following items should be checked after the
and closing the door several by opening and unit is repaired:
closing the door several times. (a) The interlock monitor switch is connected
(b) Make sure the perforated screen and the correctly and firmly.
dielectric choke of the door are correctly and (b) The magnetron gasket is properly positioned
firmly mounted. and mounted.
(c) The waveguide and the oven cavity are intact.
(2) After power is applied: (no microwave energy leakage)
(a) Make sure the interlock switch mechanism (d) The door can be properly closed and the
is operating properly by opening and closing safety switches work properly.
the door. (e) The unit must stop when the door is opened or
the time is up.
(b) Check microwave energy leakage must bebelow
the limit of 5 mW/cm2. The unit must not be operated with any of the above
(All service adjustments should be made for components removed or by-passed.
minimum microwave energy leakage
readings).
7-1
MICROWAVE LEAKAGE TEST
CAUTIONS MEASURING MICROWAVE ENERGY
LEAKAGE
Be sure to check microwave leakage prior to
servicing the oven if the oven is operative prior to Pour 27515cc of 205C(689F) water in a beaker
servicing. which is graduated to 600 cc, and place the beaker
The service personnel should inform the
on the center of the turntable.
manufacture importer, or assembler of any certified
oven unit found to have a microwave emission level Set the energy leakage monitor to 2,450 MHz and
in excess of 5 mW/cm2 and should repair any unit use it following the manufacturer's recommended
found to have excessive emission levels, at no cost to test procedure to assure correct result.
the owner, and should ascertain the cause of the When measuring the leakage, always use the 2-inch
excessive leakage. The service personnel should (5cm) spacer supplied with the probe.
instruct the owner not to use the unit until the oven has Operate the oven at its maximum output.
been brought into compliance. Measure the microwave radiation using an
If the oven operates with the door open, the service electromagnetic radiation monitor by holding the
personnel should: probe perpendicular to the surface being measured.
- Tell the user not to operate the oven.
The service personnel should check all surface and Move probe along shaded area.
vent openings for microwave leakage.
Check for microwave leakage after every servicing. The
power density of the microwave radiation leakage
emitted by the microwave oven should not exceed Probe scanning speed
4 mW/cm2. Always start measuring of an unknown field Less than 2.5 cm/sec. ( 1 in/sec)
to assure safety for operating personnel from radiation
leakage.
EQUIPMENT
TESTER (VOLTS-DC, AC, Ohmmeter)
Microwave survey meter
- Holaday HI-1500
HI-1501
- Narda 8100
8200
600 cc non conductive material beaker (glass or
plastic), inside diameter: approx. 8.5 cm (31/2 in.)
Glass thermometer: 100C or 212F (1 deg scale)
7-2
MEASUREMENT WITH THE OUTER CASE NOTE WHEN MEASURING
REMOVED (1) Do not exceed meter full scale deflection.
(1) When you replace the magnetron, measure for (2) The test probe must be moved no faster than
microwave energy leakage before the outer case 1 inch/sec (2.5cm/sec) along the shaded area,
is installed and after all necessary components otherwise a false reading may result.
are replaced or adjusted. Special care should be (3) The test probe must be held by the grip portion of
taken in measuring the following parts. the handle. A false reading may result if the
- Around the magnetron operators hand is between the handle and the
- The waveguide probe.
(4) When testing near a corner of the door, keep
WARNING: AVOID CONTACTING ANY HIGH the probe perpendicular to the surface being
VOLTAGE PARTS. tested. (Hold vertically when testing the top and
bottom, and horizontally along the side.)
MEASUREMENT WITH A FULLY
RECORD KEEPING AND NOTIFICATION
ASSEMBLED OVEN
(1) After all components, including the outer
AFTER MEASUREMENT
panels, are fully assembled, measure for (1) After adjustment and repair of any microwave
microwave energy leakage around the door energy interruption or microwave energy blocking
viewing window, the exhaust opening and air device, record the measured values for future
inlet openings. reference. Also enter the information on the
(2) Microwave energy leakage must not exceed the service invoice.
values prescribed below. (2) Should the microwave energy leakage not be
NOTES: more than 2 mW/cm2 after determining that all
Leakage with the outer panels removed less than parts are in good condition, functioning properly
5 mW/cm2. Leakage for a fully assembled oven and genuine replacement parts which are listed in
(Before the latch switch (primary) is interrupted) this manual have been used.
with the door in a slightly opened position - less (3) At least once a year, have the electromagnetic
than 2 mW/cm2. energy leakage monitor checked for calibration
by its manufacturer.
7-3
DISASSEMBLY INSTRUCTIONS
IMPORTANT NOTES: (4) Remove 3 screws securing the circuit board.
Control Bracket
FPC Connector(S1)
Power Transformer
Relay 7
(CN1)
Figure 1
Figure 3
7-4
HOW TO REMOVE THE F.P.C. CONNECTOR HOW TO INSERT THE F.P.C. CONNECTOR
Follow the steps below as illustrated in Figures 4 Follow the steps below as illustrated in Figures 6
and 5 to remove the F.P.C. connector. and 7 to insert the F.P.C. connector.
(1) Insert the F.P.C. connector into the terminal
(1) Hold the edges of the plastic fastener with socket securely with the fingers.
thumb and forefinger. (2) Hold the plastic fastener with thumb and
(Figure 4) forefinger of the other hand, and push it
(2) Lift up the lever of the plastic fastener from slowly into the terminal socket. (Figure 6)
the terminal socket by lightly pressing the NOTE: When reconnecting the F.P.C
lever end with forefinger. connector make sure that the holes
(Figure 5) on the F.P.C. connector are properly
(3) Remove the F.P.C. connector from the engaged with the hooks on the plastic
terminal socket. fastener
(3) Lock the level of the plastic fastener into the
hook of the terminal socket securely by
releasing the fingers.
Plastic fastener (Figure 7)
Plastic fastener
Hook
Holes
F.P.C.
Connector
Terminal
socket
F.P.C.
Connector
Figure 4
Terminal
socket
Plastic fastener Figure 6
Hook
Plastic
Holes fastener
F.P.C.
Connector
Terminal F.P.C.
socket Connector
Figure 5 Terminal
socket
Figure 7
7-5
B. REMOVING THE OUT CASE(Figure 8)
(1) Remove the vent grille by removing two screws (6) Remove the power cord cover from outcase by
securing it to the out case. removing a screw.
(2) Remove two screws securing it to the front bracket. (7) Remove the power cord to the inner of the out c
(3) Remove two screws securing it to the air duct. ase with turning power cord and remove the out
(4) Remove the mounting plate by turning the two case with pushing it back.
screws securing it to the out case.
(5) Remove the base plate by removing six screws
securing it to the out case. Remove the Mount, All
from the out case by removing two screws securing
it to the out case and one screw securing it to the
ventilation motor ASS'Y and cavity.
Mount, All
Power code
Door
Mounting
Plate
Out Case
Vent Grille
Controller
Figure 8
7-6
C REMOVING THE DOOR INTERLOCK
SWITCHES (Figures 9,10)
(1) Disconnect the wire leads from the interlock
switches.
(2) Remove two screws securing the Latch Board.
(3) Make necessary replacements and check
microwave energy leakage according to
ADJUSTMENT PROCEDURE on page 7-12. Latch Board
Secondary
Interlock Switch
Latch Board
WH(from H.V.Transformer)
WH(from Monitor S/W)
WH(from Oven Thermostat)
WH(from Cooktop lamp
Interlock
Monitor Switch
Primary
Interlock Switch
Monitor Interlock Switch
Figure 10
RD(from Ry 7)
7-7
D. REMOVING MAGNETRON NOTES:
(Figures 11 Through 13) When removing the magnetron, make sure that its
(1) Remove vertgrille. dome does not hit any adjacent parts, or it may be
(2) Remove mount all. damaged.
(3) Remove outcase.
(4) Discinnect the wireleads. When replacing the magnetron, be sure to install the
(5) Remove the 3 screws and Magnetron very magnetron gasket in the correct position and be sure
carefully. that the gasket is in good condition.
mount all
outcase
vertgrille
Figure 13
7-8
E. REMOVING DOOR (Figure 14)
(1) Remove the vent grille by two screws securing it to
the outcase loosening.
(2) Lift up and draw the door.
NOTES:
After replacing the door, be sure to check that the
primary interlock switch, the secondary interlock
switch and the interlock monitor switch is in good
operating normally.
After replacing the door, check for microwave energy
leakage with a survey meter. Microwave energy
leakage must be below the limit of 5mW/cm2. (With a
275 ml water load)
Figure 14
Door Screen
Figure 15
7-9
G. ASSEMBLING DOOR
(1) When mounting the door assembly to the oven (3) Carefully pull the ventilation motor ASS'Y out of the
assembly, be sure to adjust the door assembly microwave oven. (See Figure18)
parallel to the chassis. Also adjust so the door has no
play between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.
Space
Figure 18
Figure 16
MOUNT, ALL
Figure 17
7-10
I. REMOVING THE TURNTABLE MOTOR
(1) Remove the turntable.
(2) Remove the turntable shaft VERY CAREFULLY
with a slotted screwdriver. (Figure 19)
(3) Remove the base plate by removing 6 screws
securing it to the oven cavity. (Figure 20)
(4) Disconnect the leadwire from the turntable motor
terminals.
(5) Remove the 2 screws securing the turntable motor
to the oven cavity ASS'Y. (Figure 21)
NOTES:
Remove the leadwire from the turntable motor VERY
CAREFULLY.
Be sure to grasp the connector not the wires when
removing.
Figure 19
Figure 20
Wire Leads
Turntable Motor
Figure 21
7-11
INTERLOCK SYSTEM
INTERLOCK MECHANISM
The door lock mechanism is a device which has been specially designed to eliminate completely microwave
activity when the door is opened during cooking and thus to prevent the danger resulting from the microwave
leakage.
ADJUSTMENT PROCEDURES
To avoid possible exposure to microwave energy CHECK THE DOOR LATCH AND SWITCH
leakage, adjust the door latches and interlock CLOSING.
switches, using the following procedure.
NOTE:
The Interlock Monitor and Primary Interlock Switch act The outer cover of the microwave oven is
as the final safety switch protecting the user from removed.
microwave energy. The terminals between COM and
NC of the Interlock Monitor must close when the door (1) Set the microwave oven on its side so that you can
is opened. After adjusting the Interlock Monitor Switch, see the latch board and the switches, as shown in
make sure that it is correctly connected. Figure 22.
Mounting of the primary/monitor/secondary switches to
the latch board. (2) Close the door tightly and check gaps A and B to
be sure they are no more than 1/64 (0.5 mm).
See Figure 23 for close-up view of gaps A and B
(door latches). If all gaps are less than 1/64
(0.5 mm), adjustment of the latch board may not
be necessary. Go to Steps 5 and 6 to check the
Latch Board
sequence of the switches.
Secondary NOTE:
Interlock Switch
To correct sequence of the Primary Interlock
Switch, Secondary Interlock Switch and the
Interlock Monitor Switch is very important.
If any gap is larger than 1/64 (0.5 mm), you will
need to adjust the latch board. Go to step 3
and follow all steps in order.
Primary (4) With the oven door closed tightly, move the latch
Interlock Switch
board upward toward the top of the oven and/or
Figure 22 away from the door latch until the gaps are less
than 1/64 (0.5 mm).
Hold the latch board tightly in this position until you
LATCH check the sequence of the switches in steps 5
and 6.
0-1/64"
Figure 23
LATCH BOARD
0-1/64"
7-12
TEST THE LATCH AND SWITCH SEQUENCE
(5) Open the oven door slowly. Watch the door latch, (7) When you achieve the proper sequence of
the Secondary Switch. Release Rod and Lever switches in Steps 5 and 6, tighten the latch board
on the switches to make sure they are zero to the screws at that point.
body of the switches in the following sequence:
TEST THE MICROWAVE ENERGY LEAKAGE
- Primary Interlock Switch
- Secondary Interlock Switch Make sure the microwave energy leakage is below the
- Interlock Monitor Switch limit of 1mW/cm2 (with a 275 ml water load) and
5mW/cm2 (with a 275 ml water load without the
Adjust the latch board until the switches operate in cabinet) when measured with a survey meter.
this sequence. See Steps 3 and 4.
7-13
INTERLOCK CONTINUITY TEST
A. PRIMARY INTERLOCK SWITCH TEST B. SECONDARY INTERLOCK SWITCH TEST
When the door is opened slowly, an audible click Disconnect the wire lead from the secondary
should be heard at the same time or successively switch.
at intervals and the latches should activate the Connect the ohmmeter leads to the common
switches with an audible click. (COM) and normally open (NO) terminals of the
If the latches do not activate the switches when the switch. The meter should indicate an open circuit
door is closed, the switches should be adjusted in in the door open condition. When the door is
accordance with the adjustment procedure. closed, the meter should indicate a closed circuit.
Disconnect the wire lead from the primary switch. When the secondary switch operation is abnormal,
Connect the ohmmeter leads to the common make the necessary adjustment or replace the
(COM) and normally open (NO) terminal of the switch only with the same type of switch.
switch. The meter should indicate an open circuit
in the door open condition. C. MONITOR SWITCH TEST
When the door is closed, the meter should indicate Disconnect the wire lead from the monitor switch.
a closed circuit. Connect the ohmmeter leads to the common
When the primary switch operation is abnormal, (COM) and normally closed (NC) terminals of the
make the necessary adjustment or replace the switch. The meter should indicate a closed circuit
switch with the same type of switch. in the door open condition. When the door is
closed, the meter should indicate an open circuit.
When the monitor switch operation is abnormal,
replace with the same type of switch.
NOTE: After repairing the door or the interlock
system, it is necessary to do this continuity
test before operating the oven.
Primary NO
COM
Switch
Monitor NC
COM
Switch
Secondary
Switch COM
NO
NOTE : After checking for the continuity of switches, make sure that they are
connected correctly.
7-14
TEST AND CHECKOUT PROCEDURES, AND TROUBLE SHOOTING
- CAUTIONS -
Primary
Winding
Figure 24
A. TEST PROCEDURES
COMPONENTS TEST PROCEDURES RESULTS
NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
7-15
COMPONENTS TEST PROCEDURES RESULTS
Abnormal reading:
Ohm-
Indicates continuity or infinite ohms
meter
from the beginning.
Abnormal reading:
Ohm- Indicates continuity.
meter
Figure 25-b
Abnormal reading:
Infinite.
Ohm-
meter
Abnormal reading:
Ohm- continuity.
meter
Figure 26-b
7-16
COMPONENTS TEST PROCEDURES RESULTS
Measure the resistance between terminal
When When not
pins of connector KEY CONNECTOR.
Resistance touched touched
NOTE:
value
When reconnecting the FPC connector, Less than More than
make sure that the holes on the FPC 400 ohms 1 mega ohm
connector are properly engaged with hooks
on the plastic fastener.
FPC CONNECTOR
MATRIX CIRCUIT FOR Top
TOUCH KEY BOARD
TOUCH KEY CONNECTOR(KEY CON) 1
2
BOARD (For detail matrix circuit of each model, 3
refer to page 5-2.) 4
5
6
7
AUTO TIME 8
COOK COOK 9
AUTO AUTO
10
CUSTOM
SET REHEAT DEFROST 11
12
CLOCK Ez On
KITCHEN 13
TIMER
TIME POWER
N.C
DEFROST LEVEL Figure 28
STOP/ N.C
CLEAR
Figure 27
7-17
COMPONENTS TEST PROCEDURES RESULTS
NOTES:
A MICROWAVE ENERGY TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR
ANY REASON.
MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT
THE WIRES.
B. CHECKOUT PROCEDURES
(1) CHECKOUT PROCEDURES FOR FUSE BLOWING
PROBLEMS CAUSES
Fuse blows when the door is closed and START Malfunction of the high voltage transformer; the high
key is touched. voltage capacitor including the diode, the magnetron,
the blower motor or the circuit board.
NOTES:
If the fuse is blown by an improper switch operation, replace the all Interlock switches, PCB Assy and the fuse at
the same time. After replacing the the all Interlock switches, PCB Assy,Fuse with new ones, make sure that they
are correctly connected.
Check for microwave energy leakage according to INTERLOCK ADJUSTMENT PROCEDURES on page 7-12
when the primary interlock, secondary interlock switches and/or the interlock monitor switches are adjusted or
replaced.
7-18
(2) CHECKOUT PROCEDURES FOR RELAY.
- PROBLEM (A) -
T.T. motor and oven lamp turn on without touching
START key when the door is closed.
NO YES
NO YES
Replace
RELAY3
- PROBLEM (B) -
T.T. motor and oven lamp turn on When the door is
closed and START key is touched.
YES NO
NO YES
Defective
Replace the RELAY3 or poor
circuit board connection of
RELAY3
Replace
RELAY3 or correct
the connection.
7-19
(3) CHECKOUT PROCEDURES FOR CIRCUIT
BOARD
The following symptoms indicate a defective circuit 6) Wrong figures appear.
board. 7) The figures of all digits.
1) The start function fails to operate but the high 8) Some of the indicators do no flicker light up.
voltage Systems, the interlock switches, the door 9) The clock does not keep time properly.
sensing and the relay check good.
2) The unit with a normal relay continuously operates.
3) Proper temperature measurement is not obtained.
4) The buzzer does not sound or continues to sound.
5) Some segments of one or more digits do not light
up, or they continue to light up, or segments light
when they should not.
NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
7-20
C. TROUBLE SHOOTING
Before following this troubleshooting read TRIAL OPERATION on page 6-1.
DISPLAY Problems, A thru C
HELP UP Problems, D thru E BUZZER Problems, F
PROBLEM - A: PLEASE SET TIME OF DAY does not appear in display window when power supply cord is
plugged into wall outlet.
0 120
0 120
Measure voltage between pin 1
and pin 3 of connector CN1.
Voltage Correct Normal Runs
incorrect connections resistance
7-21
1
Runs
Contact Replace Normal
ok circuit board circuit board
Runs
Poor Correct Normal
contact seating contact
Measure resistance of touch
key board after removing
connector S1.
(See page 7-4 and 7-17)
Runs
Resistance Replace touch Normal touch
incorrect key board. key board
PROBLEM - C: Unit does not heat up even if display counts down when
START key is touched for "HIGH POWER" cooking.
NO Replace Runs
Normal
continuity circuit board circuit board
7-22
Normal H.V.T.
incorrect
7-23
PROBLEM - E : Ventilation fan does not operate when FAN HIGH/LOW key is touched.
NO Replace Runs
contact oven thermostat
7-24
ventilation ventilation
motor ASSY motor ASSY
EXPLODED VIEW
DOOR
13581A
13552A
13536A
13213A
13720D
WTT028
14890A
14026A
14970A
13650A
8-1
CONTROL PANEL
268711
24781M
24810P
WTP018
23572A
WTT029
*07
23506A
8-2
OVEN CAVITY
WTT021
WTT028 34960A
WTT029
WTT029
33530A
34810Q
33112U
*01
*05 *02
*04
368771
535501
63302A 63303A
36912C
34890C
34810T
WTT022
35230A WTT022
8-3
LATCH BOARD
43500A
466001
WSZ084
43501A
466003
466001
44510A
8-4
INTERIOR (I)
WSZ002
33390G
56324A
34370T
53300A
35889A
WTT021
WTT021
WSZ098
56170D
33740A
33052A
WTT021
WTT021
36549S
WTP013
WSZ002 53300B
56851D
WSZ002
54810C
50CZZH
8-5
INTERIOR (II)
56912B
55231C
53550L
36549V
56804A
WTT028
56411A
55262A
50FZZA
56930V
55006F
568771
WSZ002
8-6
INSTALLATION
44360A WSZ098
WSZ133
WBZZ02
WWZ068 WWZ068
WBZZ01 63300M
65862D
WSZ136
65862B
63861A
8-7
SCHEMATIC DIAGRAM OF P.C.B
8-12
CUSTOM
SET
CLOCK EZOn KITCHEN
N.C
N.C
LEVEL
N.C
N.C
PRINTED CIRCUIT BOARD
8-13
July, 2002
P/NO : 3828W5S2380 Printed in Korea