MN 202002 en
MN 202002 en
ii Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Contents
Product information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Acceptance and initial inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quality standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Final inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Liquid level gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Liquid temperature gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pressure-vacuum gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pressure relief device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Winding temperature gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Transformer cooling fans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
High voltage bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Low voltage bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
De-energized tap-changer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Insulating liquid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Vacuum fault interrupter (VFI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Periodic inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Removing and replacing bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Removing and replacing draw lead type bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Removing and replacing fixed stud or spade type bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cover removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Insulating liquid maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Applicable standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
R-Temp fluid-filled transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Dielectric strength. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 iii
! !
SAFETY
FOR LIFE Safety for life SAFETY
FOR LIFE
Eaton meets or exceeds all applicable industry standards relating to product safety in its Cooper Power series products.
We actively promote safe practices in the use and maintenance of our products through our service literature, instructional
training programs, and the continuous efforts of all Eaton employees involved in product design, manufacture, marketing,
and service.
We strongly urge that you always follow all locally approved safety procedures and safety instructions when working around
high voltage lines and equipment, and support our Safety For Life mission.
Safety information
The instructions in this manual are not intended as a Safety instructions
substitute for proper training or adequate experience in the Following are general caution and warning statements that
safe operation of the equipment described. Only competent apply to this equipment. Additional statements, related to
technicians who are familiar with this equipment should specific tasks and procedures, are located throughout the
install, operate, and service it. manual.
A competent technician has these qualifications:
Is thoroughly familiar with these instructions. DANGER
Is trained in industry-accepted high and low-voltage safe Hazardous voltage. Contact with hazardous voltage will
operating practices and procedures. cause death or severe personal injury. Follow all locally
approved safety procedures when working around high-
Is trained and authorized to energize, de-energize, clear,
and low-voltage lines and equipment. G103.3
and ground power distribution equipment.
Is trained in the care and use of protective equipment
such as arc flash clothing, safety glasses, face shield, hard
hat, rubber gloves, clampstick, hotstick, etc. WARNING
Following is important safety information. For safe installa- Before installing, operating, maintaining, or testing this
tion and operation of this equipment, be sure to read and equipment, carefully read and understand the contents
understand all cautions and warnings. of this manual. Improper operation, handling or
maintenance can result in death, severe personal injury,
and equipment damage. G101.0
WARNING
Indicates a potentially hazardous situation which, if not WARNING
avoided, could result in death or serious injury. Power distribution and transmission equipment must
be properly selected for the intended application. It
CAUTION must be installed and serviced by competent personnel
who have been trained and understand proper safety
Indicates a potentially hazardous situation which, if not procedures. These instructions are written for such
avoided, may result in minor or moderate injury. personnel and are not a substitute for adequate training
and experience in safety procedures. Failure to properly
CAUTION select, install or maintain power distribution and
transmission equipment can result in death, severe
Indicates a potentially hazardous situation which, if not personal injury, and equipment damage. G122.3
avoided, may result in equipment damage only.
iv Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Product information 2. Before unloading the transformer, make an inspection to
detect any signs of damage or mishandling. Locate any
accessory parts that may have been shipped separately.
CAUTION 3. If any damage is detected or shortages are noticed,
Do not Exceed Transformer Ratings. Transformers write a brief description on the freight bill. Normally, the
should be operated only at the ratings specified on the transformer is shipped FOB point of manufacture, and
transformer nameplate. Prolonged overload operation it is the customer's responsibility to file a claim against
will measurably shorten the projected service life of a the carrier. If the transformer was shipped FOB destina-
mineral oil-filled transformer. Eatons Cooper Power tion, notify your factory representative. He or she will,
series PEAK transformers may help to extend with the inspector's report, take the necessary steps to
insulation life and can be operated at higher capacities file a claim against the carrier.
than traditional units while still exceeding ANSI
standard insulation life.
Handling
For unloading, lifting hooks are provided near the top of the
Introduction transformer tank. Cable pull angles should not be over 30
This manual has been prepared to assist competent techni- from vertical. Otherwise, spreaders should be used to hold
cians in the installation, operation and service of primary or the lifting cables apart to avoid any bending of the structure
secondary unit- or open-type substation trans-formers. or lifting hooks.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 1
Installation Transformers equipped with an internal terminal board are
normally shipped with the higher voltage connected, unless
otherwise specified by the customer.
Installation location A secure and effective low resistance ground is essential
The transformer should be located on a concrete pad of for protection. The transformer must be grounded perma-
sufficient strength to support the weight of the unit. The nently by connecting a heavy ground cable to the ground
pad must be level. The location of the transformer, whether pad located at the bottom of the tank. If the transformer is
indoor or outdoor, should provide for adequate accessibility, designed for operation in a solidly grounded neutral system,
ventilation and ease of inspection. The transformer should the neutral connection should be solidly and permanently
be at least 24 inches from any obstruction. These are grounded with minimum resistance.
the recommendations of the manufacturer for operation
purposes; see your local codes for additional guidelines. Warning
Location in areas of corrosive chemicals should be avoided.
Improper grounding may result in personal injury or
These substation transformers are built to operate at damage to the equipment.
altitudes up to 3300 feet at 30C average and 40C
maximum ambient, unless otherwise specified. Before Lightning arresters are recommended for every trans-former
operating a standard transformer at higher altitudes, contact installation. Arresters of proper rating should be located as
your factory representative. close as possible to the transformer terminations.
Adequate ventilation must be provided. For indoor When alarm contacts or controls are supplied with the
installations, room air inlets should be located at floor level; transformer accessories, a connection box may be provided
the air outlets should be located as high as the room will to facilitate termination of the customer's cable or conduit.
permit. The number and size of the air inlets depends upon
the rating of the transformer. In general, about 20 square
feet each of inlet and outlet area should be provided for Final inspection
each 1000 kVA of transformer capacity. If the ventilation The final inspection can be done in three major steps:
system is adjustable, it should be locked permanently open Electrical, Internal and External.
to avoid overheating of the transformer in case of operator
error. Warning
Do not tamper with interlocks, alarm or control circuits.
Connections Doing so can produce unsafe conditions for operators or
Connections must be made without placing undue stress result in damage to the equipment.
on the bushing terminals. Conductors should be securely Electrical inspection should determine that:
fastened in place and supported properly, with allowance
for expansion and contraction. Make sure that the tap 1. All external connections have been made properly
connection is proper for the required voltage. Changes in (phasing of connections to terminal bushings, etc.).
tap connections must be done ONLY with the transformer
2. All connections are tight and secure.
high voltage and low voltage circuits completely
"DE-ENERGIZED". Safely verify that there is no voltage 3. All accessory contact circuits are operational.
present at the terminals.
4. Current transformer circuits, if supplied, have secondar-
ies either shorted or connected through their load.
Warning
5. Tap changer is operative and properly positioned.
Do not change connections on a transformer that is
energized. Ground all circuits before making any trans- 6. The correct transformer ratio exists for units furnished
former connection. Failure to observe precautions when with internal terminal board.
making connections can result in exposure to high volt-
ages, which can cause death, severe personal injury or 7. There is no grounding of windings that are not
damage to the equipment. intended to be grounded. A 1000-volt megger test is
recommended.
Do not make any connections, except as authorized by 9. The dielectric strength of the insulating liquid is
the nameplate or schematic. Improper connections 30 kV minimum when new. (Refer to section for
can result in severe personal injury and damage to the "Testing Insulating Liquid" in this manual.)
equipment. 10. The neutral and ground connections have been properly
made.
2 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
If an internal inspection is required, assure that:
1. There is no evidence of moisture.
2. All available bolted connections are tight.
3. There has been no shifting of any parts or any other
damage.
The external inspection should determine that:
1. All scratches have been painted.
2. The bushings are clean.
3. The accessories are operative.
4. There are no tools, or other objects, left on top of the
transformer or inside any enclosure.
5. The liquid level is correct.
6. The transformer holds positive pressure.
7. The manhole covers are tightly bolted.
8. All protective covers are closed and bolted tight.
9. The mechanical pressure relief device is reset.
caution
Whenever it is necessary to open a liquid-filled trans-
former, insure that the liquid temperature is higher
than the outside air temperature. Otherwise, internal
moisture condensation may occur, which could lead to
failure of the transformer.
caution
Before breaking the seal of any handhole, manhole or
bushing hole, bleed internal pressure to zero. Seals
should not be broken in the presence of fog, rain or
snow, or if there is any evidence of condensation on the
transformer tank. If even a very slight amount of such
moisture enters the transformer tank, it can decrease
the dielectric strength of the cooling liquid to danger-
ously low levels, which can result in damage to the
equipment.
caution
Only authorized personnel should be permitted on top
of the transformer and every precaution should be taken
to avoid dropping objects into the transformer. Workers
should not have anything in their pockets (such as pens,
pencils, coins, etc.) and their clothing should not have
loose metal buttons, badges, buckles, etc. Wristwatches
should also be removed. When dropped into the
transformer tank, such objects can cause equipment
malfunction and damage.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 3
Accessories Liquid temperature gauge
4 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Pressure-vacuum gauge Pressure relief device
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 5
Winding temperature gauge Transformer cooling fans
Transformers may be furnished with a winding temperature In order to increase the transformer load without
gauge as optional equipment. A temperature sensitive overheating the windings, a set of fans can be furnished as
stem is mounted in a leakproof well, permitting removal of an optional item. Fan control consists of a contact on either
both the instrument and stem without lowering the liquid the liquid temperature gauge or the winding temperature
level. The well is heated by both the surrounding liquid gauge (when furnished), and "Manual-Auto" control switch.
and a heater element which is energized from a current
transformer mounted inside the tank to simulate the hot For continuous run, the switch is turned to the "Manual"
spot winding temperature gradient. The combination of the position. In the "Auto" position, the fans are controlled by
two temperatures is indicated on the gauge. An additional the contacts on the temperature gauge. For contact and
red pointer is furnished to show the highest temperature temperature settings, refer to the schematic furnished with
attained since the last reset. The maximum indicator is the transformer.
resettable by means of a pushbutton through the bottom of
the dial bezel. warning
The gauge has three separate SPDT switches for fan control Fan guards are furnished and installed for your
and alarm circuits. For wiring the contact settings, refer to protection. Do not remove fan guards or probe into
the schematic furnished with the transformer. the fan with long objects. Doing so can result in severe
personal injury and equipment damage.
The equipment is calibrated to indicate the hottest spot
Refer to wiring schematic for control equipment supplied.
of the transformer windings. All contacts are factory set
to operate at the temperatures shown in the connection
diagram.
If readjustment of the contacts is desired, consult the
factory for detailed instruction.
6 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
High voltage bushings Low voltage bushings
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 7
De-energized tap-changer Insulating liquid
The insulating liquid in substation transformers is
either conventional transformer oil, R-Temp fluid or
Envirotemp FR3 fluid. When makeup liquid is required,
use only approved fluid of the same type that is in the
transformer. It is important to check the proper liquid level
in the transformer at all times by periodically observing the
liquid level gauge. In addition, the dielectric strength of the
insulating liquid must be maintained at a high value.
It is recommended that a sample be taken of the liquid and
tested within one week after energization, and annually
thereafter.
warning
Do not operate the tap-changer while the transformer is
energized. Doing so can result in severe personal injury
and equipment damage.
The tap-changer provides a means of changing the voltage
ratio of a de-energized transformer without breaking the
transformer seal. It is operated by means of a rotatable
handle located on the side of the transformer. The tap-
changer is normally provided with five or seven positions,
as indicated on the tap-changer dial plate and transformer
instruction nameplate.
8 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Vacuum fault interrupter (VFI)
IMPORTANT
warning For 75C AWR transformers, applications with
maximum ambient temperatures exceeding 30C or
Hazardous voltage. Can cause severe injury, death, or
loading in excess of nameplate rating, contact your
damage to equipment.
Eaton representative.
D
o not operate loadbreak equipment if a fault Eatons Cooper Power series VFI transformers utilize
condition is suspected. Doing so can cause an vacuum interrupters to provide fault current interruption and
explosion or fire. load make/break switching capabilities. The VFI transformer
uses the same technology used in Eatons Cooper Power
U
se a hotstick to operate transformer loadbreak series VFI pad-mounted switchgear.
equipment.
VFI transformers can be specified for either transformer
protection or loop protection. A VFI transformer with
After operating transformer loadbreak equipment,
transformer protection protects the transformer and
check that voltages at transformer terminals are
provides proper coordination with upstream protective
the expected values. Checking voltages verifies that
devices. A VFI transformer with loop protection protects
loadbreak equipment operated properly and that
the loop or downstream section of a feeder. Consequently,
electrical circuit conditions are as expected.
when a fault occurs downstream, the VFI breaker trips and
isolates the fault, leaving the transformer load uninterrupted.
B
efore servicing transformer secondary connected
equipment, verify that all transformer secondary The VFI interrupter mechanism in a VFI transformer has a
terminals have zero voltage and ground the hotstick-operable handle located on the faceplate of the
transformer secondary terminals following industry transformer, with the operating mechanisms configured
accepted safe grounding practices. Grounding for ganged three-phase operation (see Figure 24). The VFI
secondary terminals protects against situations such interrupter mechanism is opened by pulling the operation
as a standby generator energizing transformer from handle down to the open position. The VFI interrupter
the secondary circuit. mechanism is closed by briskly pushing the handle up,
into the closed position. If the VFI interrupter mechanism
B
efore servicing transformer, ALWAYS de-energize has tripped as the result of a fault or overload condition,
the transformer from a remote upstream source and the mechanism must be reset before it can be closed. To
then proceed to ground all primary and secondary reset the mechanism, firmly pull the operation handle down
transformer terminals following industry accepted toward the ground until the latch resets. After the latch has
safe grounding practices. Grounding secondary been successfully re-set, the VFI interrupter mechanism can
terminals protects against situations such as a be closed normally.
standby generator energizing transformer from the
secondary circuit.
F
ollow industry accepted safety practices. Utilize
protective clothing and equipment when working
with loadbreak equipment.
warning
Three-phase pad-mounted transformers use
conventional transformer oil, R-Temp fluid, or
Envirotemp FR3 fluid for an insulating liquid. When
the insulating liquid temperature is less than -20C
(-4F) for conventional transformer oil, less than 0C
(32F) for R-Temp fluid or less than -10C (14F) for
Envirotemp FR3 fluid, viscosity is reduced, which
may reduce make and break capabilities of loadbreak
devices. Below these temperatures, under-oil loadbreak
accessories should not be used to make or break a
load. Instead, de-energize transformer from a remote
upstream source before operating under-oil loadbreak
devices.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 9
Current-sensing transformers (CTs) located inside the
VFI transformer provide line current information to the
electronic control. When line current exceeds the minimum
trip setting, the control initiates a signal which causes the
VFI interrupter mechanism to trip and then interrupt the
circuit. All three phases will open when the VFI interrupter
mechanism is tripped, regardless of whether the trip was
single-phase or three-phase initiated.
Refer to Service Information S285-75-1, Tri-Phase, TPG,
and TPG with SCADA Electronic Control Installation and
Operation Instructions for electronic control operation
instructions.
Standard electrical ratings for Eaton VFI transformers are as
follows:
Continuous Current (max) . . . . . . . . . . . . . . . . . . . . . 600 A
Interrupting Current (sym./asym.) . . . . . . . . . . 12 kA/20 kA
Momentary Current 10 cycles (asym.) . . . . . . . . . . . . 20 kA
1-Second Withstand Current (sym.). . . . . . . . . . . . . . . 12 kA
Making Current (sym.) . . . . . . . . . . . . . . . . . . . . . . . . . 12 kA
For further information on Eaton VFI transformers including
additional ratings, contact your Eaton representative.
10 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Maintenance Removing and replacing draw lead type bushings
Removing
Periodic inspection 1. Unscrew and remove the top terminal cap, exposing
1. External: Periodically check the condition of the paint the threaded stud end of the draw lead cable. In some
and finish, especially when the transformer is exposed cases, the threaded stud will be held by a pin that must
to inclement atmospheric conditions. If weathering also be removed.
takes place, clean the tank thoroughly, wipe off any
insulating liquid that might have been spilled on the 2. Fasten a pull wire, cord or rod to the stud in order to
surface and repaint with a factory approved paint. guide the lead through the bushings bore and prevent
Occasionally, inspect and tighten all bolted joints and it from falling into the opening when the bushing is
check for leaks. removed. (In some cases, the lead will be of sufficient
thickness to be self-supporting; if so, this part of the
2. Regularly inspect all gauges. The liquid level must procedure can be omitted).
remain normal, considering the temperature effect.
Refill when samples have been taken. Prolonged 3. Remove the bushing mounting clamp nuts at the tank
periods of zero pressure could indicate a gas leak and to release the mounting clamp plate and free the
should be checked out. The liquid temperature should bushing for removal.
not rise higher than the design value on the nameplate, 4. Remove the bushing, guiding the draw lead conductor
plus ambient temperature. and terminal stud through the base of the bushing.
3. Liquid samples should be taken periodically and
analyzed as indicated under "Sampling". It is recom-
mended that you keep a log of the test values to
determine when reconditioning or replenishing service
is required.
warning
Before working with bushings, make sure that the Figure 11. Draw lead type bushing.
transformer is de-energized and that all circuits to
and from the transformer are grounded in order to
discharge any stored energy and prevent accidental
re-energization. Failure to do so may result in death,
severe personal injury and equipment damage.
Additional precautions include the following:
Lock in the open position disconnect switches in the
supply lines to and from the transformer.
If the transformer is under vacuum or pressure, bring the
tank to ambient pressure.
If the bushing to be removed is below the liquid level,
lower the level sufficiently to prevent fluid loss.
To protect from the atmosphere and contaminants, store
in clean, dry, sealed containers any removed liquid that
will be returned to the transformer.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 11
Replacing Replacing
Replacement draw lead type bushings can be installed by Replacement bushings can be installed by following the
following the removal procedure in reverse order. Clamp removal procedure in reverse order. Clamp bolts should be
bolts should be tightened as specified in Table 1. tightened as specified in Table 1.
The gasket under the bushing mounting flange and the The gasket under the bushing mounting flange should be
top gasket should be new or in good condition to ensure a new or in good condition, and the gasket mating surfaces
positive seal. The gasket mating surfaces must be clean and must be clean and smooth.
smooth.
After installing and connecting the new bushing, replace
The threaded stud is keyed to the inside of the bushing to the inspection opening cover, making certain the gasket is
prevent rotation while the terminal cap is being tightened. It in good condition and the gasket mating surfaces are clean
is important to have the threaded stud correctly seated. This and smooth.
can be accomplished by pulling the stud up and turning it
until it is aligned and seated. Return to the transformer any liquid removed and check for
the correct level.
A brief pressure test of the transformer at 5 psig to confirm
Removing and replacing fixed stud or spade type the integrity of the seals around all openings above the
bushings liquid level is recommended. A solution of soap and water
will give indication of a leak by the presence of bubbles.
Removing
1. Remove inspection cover (manhole) nearest to bushing,
only after all precautions outlined under "Removing and
Replacing Bushings" have been taken. TABLE 1 Torque Values
2. To remove the inspection cover: Bushing Clamps
A. Thoroughly clean the cover. Remove all dirt, grease 4-hole Aluminum Cast Bushing Clamps 70-80 in.-lbs.
and moisture. Molded Tri-Clamp Bushing 40-60 in.-lbs.
B. Release and remove cover bolts. All other 3- & 4-hole Bushing Clamps 40-60 in.-lbs.
C. Remove the cover. Lift vertically to prevent damage 2-hole Bushing Clamps 55-65 in.-lbs.
to bolt or cover gaskets.
Internal Spade Bushings
3. Unbolt the connectionsusually flexible strapsfrom the
bottom end of the bushing stud. 1/2" Steel (Grade 8) 50 ft.-lbs.
4. Remove the bushing mounting clamp nuts at the tank 3/8" Steel (Grade 8) 50 ft.-lbs.
to release the mounting clamp plate and free the
bushing for removal. Internal Stud Bushings
3/8"-16 Brass Nuts 16 ft.-lbs.
5. Remove the bushing.
5/8"-11 Aluminum Nuts 60 ft.-lbs.
5/8"-11 Brass Nuts 75 ft.-lbs.
1"-14 Brass Nuts 121 ft.-lbs.
Bushing Lead Block, Steel Hardware 110 ft.-lbs.
12 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Cover removal To reinstall the bolt-on main tank cover
(For Envirotemp FR3 fluid-filled units, see Insulating 1. Return the gasket sections to their original positions
Liquid Maintenance Section before continuing.) and orientation.
Transformers that have been system connected should be 2. Reinstall the cover, using 25 ft-lbs. torque to tighten the
de-energized, grounded, and disconnected before being cover hardware. After installing all the nuts, re-torque
opened for inspection. each nut to insure the proper torque is achieved.
Substation transformers may have either bolt-on or weld- 3. Remove the pressure relief valve and pressurize the
in-place main tank covers. Access to the interior of a trans- headspace to insure that there are no leaks. The pres-
former with a bolt-on main tank cover without handholes sure should not exceed 7 psig. The established pres-
requires removal of the entire cover. Access to the interior sure should be maintained for at least four hours to
of the welded-in-place main tank cover design is typically insure that all the seals are proper.
through manhole or handholes.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 13
Insulating liquid maintenance Filtration should be continued until the dielectric test of the
insulating liquid is 26 kV or better.
Sampling insulating liquid
NNote: A sample of the liquid should be taken when the unit
caution
is warmer than the surrounding air to avoid conden- When filtering any insulating fluid, the filtering
sation of moisture on the liquid. Liquid samples must equipment must be free of contaminants and other
be drawn from the sampling valve located at the liquids. The presence of other liquids may alter the
physical and electrical characteristics of the fluid.
bottom of the transformer tank.
Containers used for sampling liquid should be clean and dry
large mouth glass bottles. Applicable standards
Do not permit the fluid to splash into the receiving
container. Splashing can introduce air and moisture into 1. IEEE Std C57.91-2011 standard, "Guide for Loading
the fluid. Rinse the bottle three times with the liquid being Mineral Oil Immersed Transformers."
sampled. Make sure the liquid being sampled is representa- 2. IEEE Std C57.93-2007 standard "Guide for Installation
tive of the liquid in the unit. and Maintenance of Liquid Immersed Power
Test samples should be taken only after the liquid has Transformers."
settled for some time eight hours for a barrel, up to 3. IEEE Std C57.106-2006 standard, "Guide for
several days for a large transformer. Cold insulating liquid Acceptance and Maintenance of Insulating Oil in
is much slower in settling. Liquid samples from the trans- Equipment."
former should be taken from the sampling valve at the
bottom of the tank. 4. ASTM Specification #D 877, "The Standard Method of
Testing Electrical Insulating Oils."
warning 5. IEEE Std C57.121-1998 standard, Guide for
Do not lower fluid in tank to a level below the top Acceptance and Maintenance of Less Flammable
of the core clamp. Insufficient fluid risks unit failure, Hydrocarbon Fluid in Transformers.
which could result in severe personal injury or death to
exposed personnel.
When sampling, a metal or non rubber hose must be used
R-Temp fluid-filled transformers
because oil leaches the sulfur found in rubber. The presence
of sulfur can prove harmful to transformer components. Periodic maintenance tests for R-Temp fluid-filled
transformers should be performed on essentially the same
When drawing samples from the bottom of the transformer schedule as would be used for conventional mineral oil-filled
or large tank, sufficient liquid must first be drawn off to transformers of similar application. The same type of
ensure that the sample will be from the bottom of the tank, sampling techniques should be used. Basic recommended
and not the liquid stored in the sampling pipe. tests for R-Temp fluid-filled transformers are dielectric
strength, moisture content, and flash and fire point.
Testing insulating liquid
For testing the dielectric strength of insulating liquids, Dielectric strength
follow the procedure specified by the American Society Although the transformer should operate satisfactorily
for Testing Materials in ASTM D-877, "Standard Method for with a fluid dielectric strength of 22 kV, an R-Temp fluid
Testing Electrical Insulating Oils." dielectric strength below 25 kV is an indication of excessive
contamination. In this case, the R-Temp fluid should be
If, at any time, the dielectric strength of the liquid drops replaced or filtered to remove the moisture or particulate
below 26 kV, it should be filtered until it tests at 26 kV or contamination.
better.
The dielectric strength of R-Temp fluid should be tested in
accordance with ASTM D 877.
Filtering insulating liquid
Transformer oil, R-Temp fluid or Envirotemp FR3 fluid
can be filtered by means of a filter press. The filter press is
effective for removing all types of foreign matter, including
finely divided carbon and small amounts of moisture. The
purifier equipment consists of a specifically proportioned
filter press, a positive volume gear pump, driving motor,
combined drip pan and mixing tank, necessary piping,
valves, strainer, gauges and a drying oven.
14 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Flash and fire points If the transformer cover or manhole must be removed
for internal service, exposure time to ambient air should
Relatively small percentages (2-3%) of transformer oil or
be minimal. Avoid exposure times greater than 24 hours.
contaminants may substantially reduce the flash and fire
Immediately after service is completed, replace the cover or
point of R-Temp fluid. If it is suspected that the fluid may
manhole. Then, purge and recharge the headspace with dry
have been exposed to contamination, the flash and fire
nitrogen.
point should be measured in accordance with ASTM D-92.
A fire point lower than 300C probably indicates some The procedure for recharging the headspace with nitrogen
contamination by lower fire point material. If flash or fire should include the following steps:
points fall below the minimum values required, retrofilling
may be required. 1. Fill headspace with dry nitrogen to a pressure of 2-3
psig.
2. Vent headspace to atmospheric pressure.
Drain and refill
If it is necessary to drain and refill the transformer, special 3. Refill headspace with nitrogen to 2-3 psig.
care should be taken to avoid the entrapment of gas 4. Verify that the unit is hermetically sealed.
bubbles in the system. Sufficient time should be allowed
between refilling and energization of the transformer to be If the manhole cover or non-flapper style Bay-O-Net fuses
sure that any gas bubbles created during the process have are removed for more than 24 hours, any oxygen absorber
dissipated. packet(s) should be replaced.
Contact your Eaton representative for additional handling
guidelines. Transformer oil contamination
Envirotemp FR3 fluid is fully miscible with oil. There
is no known detrimental performance impact when
PEAK and Envirotemp FR3 fluid-filled Envirotemp FR3 fluid is mixed with mineral oil.
transformers Conversely, except for some reduction in flash and fire
points, the same is true for oil mixed in with Envirotemp
Periodic maintenance should be performed on the FR3 fluid. More than 7% mineral oil in Envirotemp
same schedule as would be used for units of similar FR3 fluid is required to drop the fire point to below
application filled with transformer oil. The same type of 300C. To maintain its exceptional environmental
sampling techniques should be used (ASTM-D923). Basic classification, contamination of Envirotemp FR3
recommended tests for Envirotemp FR3 fluid are dielectric coolant by any other fluids should be avoided.
dielectric strength, moisture content and flash and fire Contact your Eaton representative for additional handling
points. guidelines.
Acceptance values should meet or exceed those shown in
IEC 61203, "Guide for Maintenance of Transformer Esters in
Equipment". Spare parts and service
We suggest that you keep one spare set of gaskets for
the manhole and any gasket-type bushings used. Other
caution renewal parts may be ordered through your local factory
When the insulating fluid temperature is less than 10C representative. When replacing components, including
(14F), no-load tap changers and energized loadbreak gaskets, on a PEAK transformer ensure they are rated for
switches should not be operated and the Bay-O-Net PEAK level operating temperatures. When ordering parts or
fuses should not be used to make or break a load. requesting service, provide a complete description of the
(Operations at lower temperatures may be possible part or the problem and the complete transformer serial
provided it is certified by the switching device number as listed on the nameplate.
manufacturer for loadbreak operation in Envirotemp
FR3 fluid at lower temperatures.)
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 15
Preventative maintenance instructions If any issues are found regarding the below, contact PS-WarrantyServices@
Eaton.com for assistance on transformers under warranty. Additionally, these
reports must be available upon request to maintain warranty period.
warning
Hazardous voltage. Can cause severe injury, death, or
damage to equipment. De-energize transformer from
a remote upstream source before opening cabinet
and doing cabinet interior inspection or maintenance.
Check that all transformer terminals and bushings have
zero voltage. Ground transformer following industry
accepted safe grounding practices.
16 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
Items to Inspect Points to be checked Remedial Action Frequency
Dielectric Fluid Level Check dielectric fluid level gauge. Note that the If the dielectric fluid level is below the nominal Annual
fluid level gauge has a notation as to the expected level, check transformer for signs of a leak. If a
level when the unit has an average internal fluid leak is observed, repair immediately. If no leak
temperature of 25C. A reading above this zone is observed, add oil to bring level to nominal
is normal when at full operating temperature and operating level.
does not indicate that the transformer is operating
at a temperature higher than the nameplate rating.
Fluid Temperature Check liquid temperature gauge for elevated If temperature is elevated compared to other Annual
temperature. Reset the drag hand if one exists. similar transformers, have unit serviced
Compare temperature to that of similar units. Note immediately to determine source of elevation.
that the maximum top fluid temperature as noted
by the draghand is a function of the maximum
loading on the hottest day. A rule of thumb for a
typical maximum reading would be nameplate rated
temperature rise minus 10C plus the maximum
ambient peak experienced in the area.
Example: 65C - 10C + 40C = 95C. Similar units
should be within 3C of each other at the same
location.
Fusing If bayonet fuses have been extracted, fluid might be Annual
present from that activity and may not be indicative
of a leak.
Cable Connections If there are signs of overheating, check for loose Tighten any loose connections immediately. Annual
connections or discolored spades (paddles). Any damage or discoloration that is observed
The tin plating will achieve a rainbow coloring should be addressed immediately by a qualified
if a particular terminal is experiencing an over technician.
temperature condition.
Bushings Check condition of the HV and LV bushings. If the bushings are dirty, clean them Annual
Observe for any indication of dirt, breakage, general immediately. Any damage that is observed
damage, heat damage or flashover. Note that should be addressed immediately by a qualified
excess dielectric grease from the separable dead technician.
front connectors can liquefy from the heat and
appear like an internal fluid leak.
Cubicle Padlock Check that all cubicles are locked. Replace any missing locks immediately. Annual
LV Bushing Cantilever Check for excessive cable weight or stiff cable Immediately adjust cable/conductor position to Annual
conductors putting upward or downward pressure eliminate pressure.
on the bushings due to pad settling.
Pressure Relief Valve Check for dirt, debris and operation. Replace immediately if damage. Clean if dirty or Annual
clogged with debris.
Lightning Arresters Check for damage or breakage and an intact and Replace damaged arresters and tighten or Annual
tight ground connection. secure any lose ground connections.
Dissolved Gas Analysis
Items to Inspect Points to be checked Remedial Action Frequency
Oil Sample Take an oil sample and send it to a third party Compare dissolved gas analysis results to the Annual
tester to check dissolved gas levels. baseline result. Look for abrupt changes in
dissolved gas levels. Any abrupt changes should
be investigated immediately.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 17
This page is intentionally left blank.
18 Substation transformer installation and parts replacement information MN202002EN JUNE 2016
This page is intentionally left blank.
Substation transformer installation and parts replacement information MN202002EN JUNE 2016 19
!
SAFETY
FOR LIFE
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
2016 Eaton
All Rights Reserved Eaton is a registered trademark.
Printed in USA For Eaton's Cooper Power series product
Publication No. MN202002EN All trademarks are property information call 1-877-277-4636 or visit:
June 2016 of their respective owners. www.eaton.com/cooperpowerseries.